Siemens Advance Network Gateway User`s manual

Siemens Applied Automation
Advance Network
Gateway with DataNET (ANG_DN)
February 2002
User’s Manual
2000591-001
Copyright Notice
 2000 by Siemens Applied Automation
Bartlesville, Oklahoma, 74003, U.S.A.
All rights reserved.
This publication is for information only. The contents are subject to change without notice and should not
be construed as a commitment, representation, warranty, or guarantee of any method, product, or device
by Siemens Applied Automation.
Reproduction or translation of any part of this publication beyond that permitted by Sections 107 and 109
of the United States Copyright Act without the written consent of the copyright owner is unlawful.
Inquiries regarding this manual should be addressed to:
Siemens Applied Automation
Technical Communications
500 West Highway 60
Bartlesville, Oklahoma, 74003, U.S.A.
Table of Contents
Chapter 1:
Preface
Technical Support
Safety Practices and Precautions
iii
iv
v
Introduction
1
1
4
Overview
ANG_DN Specifications
Chapter 2:
Installation
Overview
Unpacking and Inspection
Pre Installation Planning
Wall or Rack Mounting Installation
Site Wiring Requirements
CE Installations
Wiring Connections
AC Power (Mains) Connections
Data Hiway Connections
DataNET Connections
DataNET Copper Connections
DataNET Fiber Optic Connections
Chapter 3:
Chapter 4:
2000591-001
Data Communications Setup
13
13
14
15
16
18
22
24
25
28
31
32
34
Configuring Your PC
Establishing a Connection
Setting Network Address & Loop and Unit Numbers
Assigning an IP Address
Editing the Address Translation Table
Firmware Updates
39
40
44
47
50
51
56
Command Summary
59
Table of Contents • i
Table of Contents, Continued
Chapter 5:
Chapter 6:
Troubleshooting
73
ANCB Description
ANCB LEDs Description & Operation
DataNET Troubleshooting Guide
Obtaining Diagnostic Information
74
76
79
82
Parts Catalog
85
Introduction
Available Parts
85
86
Appendix
Data Hiway Testing
87
Glossary
Definitions of Important Terms
89
ii • Table of Contents
2000591-001
Preface
Audience & Purpose
This manual is intended to introduce users to the Advance Network
Gateway unit with the DataNET (ANG_DN) option. It includes instructions for safe and proper installation of the ANG_DN) by installation personnel.
Chapter Contents
The manual provides the following information:
Topic
2000585-001
Page
Chapter 1. Introduction
1
Chapter 2. Installation
13
Chapter 3. Data Communications Setup
39
Chapter 4.Command Summary
59
Chapter 5. Troubleshooting
73
Chapter 6. Parts Catalog
85
Appendix. Data Hiway Testing
87
Glossary
89
Preface • iii
Technical Support
Getting Help
At Siemens Applied Automation we take pride in the on going support we
provide our customers. When you purchase a product, you receive a
detailed manual, which should answer your questions; however, our
technical support service provides a special “hot” line as an added
source of information.
If you require assistance call:
Inside Oklahoma: (918) 662-7430
Outside Oklahoma: (800) 448-8224
Internationally: 001-918-662-7430
Before You Call
Before you call one of our technical support lines. Please have the following information available to help our representative answer your
questions:
1. Unit Serial Number and Date of Installation
2. Description of problem
3. LEDs status on Communication Boards
iv • Preface
2000591-001
Safety Practices and Precautions
Safety First
This product has been designed and tested in accordance with IEC Publication 1010-1, Safety Requirements for Electronic Measuring Apparatus, and has been supplied in a safe condition. This manual contains information and warnings, which have to be followed by the user to ensure
safe operation and to retain the product in a safe condition.
Terms in This Manual
WARNING statements identify conditions or practices that could result in
personal injury or loss of life.
CAUTION statements identify conditions or practices that could result in
damage to the equipment or other property.
Terms as Marked on
Equipment
DANGER indicates a personal injury hazard immediately accessible as
one reads the markings.
CAUTION indicates a personal injury hazard not immediately accessible
as one reads the markings, or a hazard to property, including the equipment itself.
Symbols in This
Manual
This symbol indicates where applicable cautionary or other
information is to be found.
Symbols Marked on
Equipment
DANGER - High voltage
Protective ground (earth) terminal
ATTENTION - Refer to Manual
Grounding the
Product
2000591-001
A grounding conductor should be connected to the grounding terminal
before any other connections are made.
Safety Practices and Precautions • v
Safety Practices and Precautions, Continued
Correct Operating
Voltage
Before switching on the power, check that the operating voltage listed on
the equipment nameplate agrees with the available line voltage.
DANGER Arising
from Loss of Ground
Any interruption of the grounding conductor inside or outside the equipment or loose connection of the grounding conductor can result in a dangerous unit. Intentional interruption of the grounding conductor is not
permitted.
Safe Equipment
If it is determined that the equipment cannot be operated safely, it should
be taken out of operation and secured against unintentional usage.
Use the Proper Fuse
To avoid fire hazard, use only a fuse of the correct type, voltage rating
and current rating as specified in the parts list for your product. Use of
repaired fuses or short-circuiting of the fuse switch is not permitted.
Safety Guidelines
DO NOT open the equipment to perform any adjustments, measurements, maintenance, parts replacement or repairs until all power supplies have been disconnected.
Only a properly trained technician should work on any equipment with
power still applied.
When opening covers or removing parts, exercise extreme care since
"live parts or connections can be exposed".
Capacitors in the equipment can retain their charge even after the unit
has been disconnected from all power supplies.
vi • Safety Practices and Precautions
2000591-001
Chapter 1
Introduction
Overview
Description
The Advance Network Gateway unit with the DataNET (ANG_DN) option
connects equipment residing on an Advance Data Hiway to the Advance
Communication System (ACS) via a DataNET link. The unit functions as a
translator for converting signals and communication protocols. This conversion allows Advance Maxum GC’s and Advance GC’s to communicate with
each other in addition to using each other’s Distributed Control System
(DCS) I/O links.
The DataNET link can use either copper and/or fiber optic cables. In an existing Data Hiway installation the Data Hiway cable can be used.
What is DataNET
DataNET is a Siemens Applied Automation communications protocol that
can be used in place of Ethernet for connecting all installed Maxum and Advance GC’s. As compared to Ethernet, DataNET provides a higher speed
network and minimizes installation of new field wiring.
Redundancy
The Advance Network DataNET Gateway is fully redundant with two Advance Network Communications Boards (ANCB) and power supplies. Each
ANCB provides either a channel A or channel B network interface for one
Data Hiway channel and one DataNET channel.
An internal Ethernet cross-link connection via the Ethernet 10Base2 (BNC)
port provides the communication link between the two advance network
communications boards (ANCB).
Cross Link Cable
Advance Network
Communications Board
(ANCB)
Channel A Channel B
2000591-001
Introduction • 1
Overview, Continued
Available
Configurations
The Advance Network DataNET Gateway is available in the following optional configurations:
Description
Advance Communications System
2 • Introduction
SAA Part Number
CSA/NRTL, Div 2, ADH to DataNET, Wall Mount, CE
(Copper)
2015841-001
CSA/NRTL, Div 2, ADH to DataNET, Wall Mount, CE
(Fiber Optic)
2015841-002
CSA/NRTL, Div 2, ADH to DataNET, Rack Mount, CE
(Copper)
2015839-001
CSA/NRTL, Div 2, ADH to DataNET, Rack Mount, CE
(Fiber Optic)
2015839-002
CENELEC, ZONE 1, ADH to DataNET, Wall Mount, CE
(Copper)
2015852-001
CENELEC, ZONE 1, ADH to DataNET, Wall Mount, CE
(Fiber Optics)
2015852-002
The Advance Communication System (ACS) is a high-speed communications system that uses TCP protocols and IP addressing to interconnect
chromatographs and other process analyzers in a common network. Figure
1-1 shows the Advance DataNET Hub (DNH), Advance Network Access Unit
(NAU) and Advance Network Gateway (ANG) connected to the ACS. The
NAU connects to the ACS and provides a method to access information
coming from Advance process analyzers including Advance Maxum and Advance Optichrom GC’s. The ANG is used to connect Siemens Applied Automation’s equipment residing on an Advance Data Hiway to the ACS.
2000591-001
Overview, Continued
Figure 1-1. Advance
Communication System
(ACS)
NAU
Advance Network
Access Unit
AA
Applied Automation
Workstation
DNH
Advance DataNET
Hub
AA
Applied Automation
APC
Advance Personal
Computer
PCI
AA Applied Automation
AA
AA
ANG
Advance Network
Gateway
Advance Maxum
AA Applied Automation
Advance Maxum
IOU(s)
Advance Optichrom
GC’s
Advance Optichrom Service Panels and older APC workstations can display
Advance Maxum GC information over the Gateway link. They are, however,
limited to only accessing and changing basic operational status. This data
includes alarms, run/hold/calibrate, view, analysis results etc.
Important
The Advance DataNET Hub (DNH) unit must have a software version greater
than 2.11 when interfacing with an Advance Network Gateway DataNET unit.
To update the DNH software please call Siemens AAI technical support:
Inside Oklahoma: (918) 662-7430
Outside Oklahoma: (800) 448-8224
Internationally: 001-918-662-7430
2000591-001
Introduction • 3
ANG_DN Specifications
Dimensions
Rack Mounted Package Configuration
See Figure 1-2 for Outline Drawing and Dimensions
Wall-Mounted Package Configuration
See Figure 1-3 for Outline Drawing and Dimensions
Zone 1 - Wall-Mounted Package Configuration
See Figure 1-4 for Outline Drawing and Dimension
Housing, Explosion Protection,
Ratings and Certifications
Wall Mounted Configuration
NEMA 3 (IP-54)
CSA Certified for Class I, Division 2, Group A,B,C,D
CENELEC non-Ex
(Air purge is not required for fire protection as indicated; however, the
unit may be air purged, if desired, for additional protection from environmental elements.)
Rack Mounted Configuration
NEMA 2 (IP-20)
CSA Certified for Class I, Division 2, Group A,B,C,D
CENELEC non-Ex
Zone 1 Configurations
CENELEC approved EEx d IIC T6 Cortem CCA-04 enclosure
Electromagnetic and Radio Frequency Compatibility and Electrical
Safety
CE Compliance; certified to 89/336/ECC (EMC directive)
CE Compliance; certified to 73/23/EEC (Low Voltage directive)
Tested per EN 61010-1 / IEC 1010-1
Housing Materials and Colors
Stainless steel (1.4016); Front and top are commercial gray B
(RAL 7043), housing is light gray (RAL 7035)
Weight
Rack/Wall:
Zone 1:
Electronics
4 • Introduction
15 kg (35 pounds) approximately
33 kg (73 pounds)
The electronics are certified for use in NEC Division 2 and IEC
(Cenelec) Zone 2 hazardous locations.
2000591-001
ANG_DN Specifications, Continued
Ambient Installation
Conditions
Operation: -18° to +50°C (0° to 122°F)
0-99% relative humidity (non-condensing) maximum
0-75% relative humidity year-round average
(Purge with dry air or nitrogen if required in tropical conditions.)
Must not be exposed to direct sunlight.
Must be protected from rain.
Storage and Transport: -25° to +65°C
Power
Nominal:
Tolerance:
115 Vac / 230 Vac (universal input)
85-140 Vac or 185-250 Vac; 47-63 Hz
300 watts
Power line protection: G fuse element per IEC 127-2, 4 A rating, slowblow
Power wiring in field made to screw terminals on two part connectors;
16 AWG (1.5 mm) or smaller power wiring is accepted; must conform
to local installation codes and requirements. If conformance to CE
certified installation requirements is required, power cable must be
shielded or installed in conduit.
Dual Communication
Modules
Redundant system consisting of two identical modules. Each module
consists of universal power supply and Advance Communications
Board (ANCB).
Protocol and Addressing
Open Systems standard TCP/IP protocol and addressing (Transmission Control Protocol/Internet Protocol); Full Class A, B and C addresses and subnet masking supported
Wiring Connections
•
•
•
2000591-001
Two part connectors with screw-terminals provided for AC power
connection
Two part connectors with screw-terminals provided for cable connection
Fiber Optic Coupler for Fiber Optic Connections
Introduction • 5
ANG_DN Specifications, Continued
•
DataNET Option, Standard
Cable
•
•
•
DataNET Option, Fiber Optic
Cable
Cable connection by Belden 9182 (single pair) or Belden
SSD1743 (two pairs) or equivalent; two pairs of wires are required to support redundancy
Shielded cable or unshielded cable in conduit is required for
conformance to CE certified installation
Two part connectors with screw-terminals provided for field connection
•
Fiber optics connection by 62.5 multi-mode cable corresponding
to 10BaseFL Ethernet specification
Two pairs of fibers are required to support redundancy
Type ST mating connectors provided for field connection
Approximately 3 mbps base transmission rate; uses dedicated
transmission technique that does not require collision detection to
achieve high data throughput efficiency
Maximum Length 5000 feet ( 1.7km)
Fiber Optic Coupler
•
Two (Tx, Rx) ST-Style Connectors (Amp type 2.5mm Bayonet)
Ethernet Option
•
The ANG DataNET unit does not support Ethernert.
Serial Port
•
Standard RS-232 port for attachment of a laptop computer used
for configuration and diagnostic purposes.
•
•
•
Communication
Comparisons
The Table below compares key communication features between using Advance Data Hiway, Ethernet, or DataNET.
Feature
6 • Introduction
Advance Data Hiway
Ethernet
DataNET
Speed
14.2 KB/Sec
10 M baud
2. 048 M baud
Redundant
Yes
No
Yes
Number of Units in
Maxum System
248
1200
1200
2000591-001
ANG_DN Specifications, Continued
ANG Cable Types
The following Table should be used when evaluating or selecting cable for an
existing or new installation.
Cable Type
Vendors & P/N
Installation Notes
Fiber Optic
SAA P/N 1270002-002
MM 62.5/125; 4 Fiber Conductors
Required for TX/RX Redundancy
Industry Available from
Multiple Vendors
New Installation as an alternative to copper cable
2- Conductor Copper Wire
SAA P/N 1686002-001
Belden P/N 9182
For
Belden Armored Cable
Order
SAA P/N 1680000-002
4-Conductor Copper Wire
SAA P/N 1681000-003
Belden P/N SSD1743
Max distance from Analyzer
to Hub or between Hubs
1520 meters (5000 ft)
Recommended for Single
Channel
Max distance from Analyzer
to Hub or between Hubs
1520 meters (5000 ft)
Recommended for Dual
Channel
Max distance from Analyzer
to Hub or between Hubs
1520 meters (5000 ft)
Ethernet Cat 5 STP Shielded
Twisted pair or Cat. 5 UTP in Conduit
2000591-001
SAA P/N 1681003-006
Industry Available from
Multiple Vendors
Recommended for short
distances or within shelters.
Max distance from analyzer
to hub or between hubs 600
meters (2000 ft)
Introduction • 7
ANG_DN Specifications, Continued
Figure 1-2. Rack Mount
Dimensions
A
A
D
C
F
E
B
Rack Mount, Front View
Rack Mount, Side View
L
M
M
Rack Mount, Rear View
Dimension Table
8 • Introduction
Figure 1-2
Description
U.S.
Inches
Metric
mm
A
Rack Height
6 15/16
177
B
Rack Total Width
19
483
C
Rack Mounting Holes Spacing
18 1/4
464
D
Rack Depth of Case Only
16 1/4
413
E
Rack Depth Including Cable Housing
22 1/8
563
F
Handle Depth in Front of Rack
1 3/8
35
L
Height of Rear Access Panels
5
127
M
Width of Rear Access Panels
7½
190
2000591-001
ANG_DN Specifications, Continued
Figure 1-3. Wall Mount
Dimensions
G
H
K
I
A
J
D
E
Bell housing shields
to provide for
hazardous area
connection of field
wiring.
Wall Mount, Front View
Wall Mount, Left Side View
Dimension Table
2000591-001
Figure 1-3
Description
U.S.
Inches
Metric
mm
G
Wall Depth
7 13/16
199
H
Wall Width
17 1/2
444
I
Wall Mount Holes Horizontal Spacing
15 9/16
396
D
Wall Height of Case Only
16 1/4
413
E
Wall Height Including Cable Housing
22 1/8
563
J
Wall Mount Holes Vertical Spacing
17 11/16
450
K
Left Side Wall Clearance for Door
Opening
2 3/8
60
Introduction • 9
ANG_DN Specifications, Continued
Figure 1-4. Zone 1 – Wall
Mount
R
c/l
K
0
P
BOTTOM
B
C
E
Q
D
c/l
A
J
I
H
FRONT
F
G
RIGHT
O
N
Q
LEFT
P
M
c/l
K
L
S
T
TOP
Dimension Table
Figure 1-4
A
B
C
D
E
F
G
H
I
J
K
Description
Overall enclosure height
Overall enclosure width
Overall enclosure depth from wall mounting
Vertical distance between wall mounting holes
Horizontal distance between wall mounting holes
Clearance of wall mounting holes
Distance from wall to front cable entry hole (left and right)
Distance from wall to back cable entry hole (left and right)
Spacing between holes on sides (left and right)
Spacing from center line to outer hole on side (left and right)
Spacing from wall to back cable entry hole (top and bottom)
10 • Introduction
Metric
(mm)
523
431
271
481
390
20
120
76
76
153
76
U.S. (inches)
20 9/16
16 15/16
10 11/16
19
15 3/8
13/16
4 3/4
3
3
6
3
2000591-001
ANG_DN Specifications, Continued
Figure 1-4. Zone 1 – Wall
Mount Dimension Table,
continued
Figure 1-4
L
M
N
O
P
Q
R
S
T
2000591-001
Description
Spacing from wall to front cable entry hole (top and bottom)
Spacing between front cable entry holes (top)
Spacing between center line and outer cable entry hole (top)
Spacing between center line and outer cable entry hole (top
and bottom)
Spacing between rear cable entry holes (top and bottom)
9 threaded cable entry holes each on left and right sides
2 threaded cable entry holes on bottom
2 threaded cable entry holes on top
2 threaded cable entry holes on top
Metric
(mm)
127
102
102
51
102
M25 x 1.5
M25 x 1.5
U.S. (inches)
5
4
4
2
4
1-1/4 x 11 NPT
3/4 x 14 NPT
Introduction • 11
Chapter 2
Installation
Overview
Introduction
This chapter is intended for installation personnel. After completing the
procedures in this chapter the Advance Network Gateway (ANG) will be
ready for operation. To ensure a safe and trouble free installation, follow
all procedures and associated advisory information.
WARNING
Ensure that all AC Power (Mains) Specification requirements and advisories are met. Failure to do so, and operating the equipment in a manner
not specified, may impair the safety protection provided by the equipment.
Installation Overview
Before beginning the installation process read through this Chapter to
familiarize yourself with the installations requirements. This will aid you to
ensure a safe and trouble free installation.
Topic
2000591-001
See Page
Unpacking and Inspection
14
Pre Installation Planning
15
Wall or Rack Mounting Installation
16
Site Wiring Requirements
18
CE Installations
22
Wiring Connections
24
AC Power (Mains) Connections
25
Data Hiway Connections
28
DataNET Connections
31
DataNET Copper Connections
32
DataNET Fiber Optic Connections
34
Installation • 13
Unpacking and Inspection
Description
This section provides the steps to follow when receiving and unpacking
the Advance Network Gateway (ANG).
Shipping Damage
When the unit is received, examine the shipping container for evidence
of external damage. Record any external damage.
Unpacking
Open the carton containing the ANG and remove all packing material.
Carefully remove the unit from the carton and inspect it for damage that
may have occurred during transportation. Carefully examine shipped
contents with those listed on the packing slip. All items should match
those on packing slip.
Perform the following inspections:
•
•
•
•
•
Reporting Damage
Inspect ANG exterior for dents, chipped paint, scratches etc.
Open ANG hinged top cover and visually inspect interior mounted
assemblies, and connectors.
If ANG is to be rack or wall mounted, be certain the proper mounting
hardware is provided.
Inspect all field wiring connectors and switches. There must not be
any damage to these connectors or switches.
Check internal power supply(s) for damage.
If there is any evidence of damage to the shipping carton or the ANG
notify the carrier and your local Siemens Applied Automation representative. Keep all shipping materials as evidence of damage for carriers inspection. Immediately contact your Siemens Applied Automation representative who will arrange for immediate repair or replacement. The
Siemens Applied Automation Customer Service department can be
contacted as follows:
Inside Oklahoma: 918-662-7430
Outside Oklahoma: 800-448-8224 (toll free)
Internationally: 001-918-662-7430
14 • Installation
2000591-001
Pre Installation Planning
Description
This section provides information that can help you in preplanning your
installation.
CAUTION
Before installing the Advance Network Gateway (ANG) within an existing
LAN consult with your LAN administrator.
Figure 2-1. Wall Mounted
ANG
The ANG is designed for wall or 19-inch rack mounting. Figure 2-1
shows the ANG wall mounted in an analyzer house. Note that the AC
Power (Mains) breaker is located in close proximity of the ANG. Also
note the I/O connections to the ANG_DN.
AC BREAKER
PROTECTION
POWER & CABLE
CONNECTIONS
Figure 2-2. ANG_DN
Installation
Figure 2-2 illustrates how a ANG can be used to physically extend a single loop of the Advance Data Hiway (ADH) by providing a conversion
from the ADH media to Ethernet, or DataNET and back to the ADH media.
All segments of the system labeled “Advance Data Hiway” are according
to standard installation practices (9182 Belden cable or equivalent); see
Chapter 1. ANG_DN Specifications; page 4.
Analyzer House
I/O Unit
Advance
Data Hiway
ANG
APC
Distant Analyzer House
Advance
Network
Advance Data Hiway
2000591-001
GC
GC
GC
or STP
Hub
GC
GC
Control
ANG
Analyzer House
Advance Data Hiway
ANG
GC
GC
Installation • 15
Wall or Rack Mounting Installation
Instructions
The Advance Network Gateway (ANG) should be:
•
•
•
Installed in a location that is free from shock and vibration.
Protected from direct sunlight and extremes of temperature.
It is recommended that the unit be mounted within a shelter. This
prevents it from being exposed to outside environmental conditions.
Package
Configurations
The unit is designed for standard wall or Zone 1 wall installations, or 19inch rack installations; see Chapter 1. Figures 1-2, 1-3, and 1-4. Shown
below is a typical wall mount installation for NEC Division 2 or non-rated
areas.
Wall Mounting
The mounting wall must be capable of supporting the weight of the unit;
see Chapter 1., ANG_DN Specifications and Figures 1-3 and 1-4.
Wall Mount Installation: Use four, 5/16-inch (M8) or 3/8-inch (M10) lag
bolts to mount the unit to the wall. Mounting bolts must be secured to
solid wall construction members such as studs and into the wall only.
Allow adequate clearance on the left side to allow the door to swing
open.
Zone 1 Wall Mount Installation: Use four, ¾-inch (M20) lag bolts to
mount the NAU to the wall. Mounting bolts must be secured to solid wall
construction members such as studs and into the wall only.
16 • Installation
2000591-001
Wall or Rack Mounting Installation, Continued
Rack Mounting
The ANG rack mount configuration is designed for a standard 19-inch
cabinet. The cabinet should have at least seven inches of vertical space
for mounting the unit. See Figure 1-2 for minimum width and depth
mounting dimensions.
CE Installations
For installation sites that must conform to CE (Conformite Europeene)
Certification see page 22, CE Installations.
Wiring Requirements
The wiring routing and entry requirements for the ANG are dependent
upon the site requirements; see page 18, Site Wiring Requirements:
2000591-001
•
CE (Conformite Europeene) Certified Area; see Page 22
•
NEC Division 2 or Non-Hazardous Areas
•
Cenelec Zone 1 or Zone 2 Areas
•
Rack Mounting Non-Hazardous Area.
Installation • 17
Site Wiring Requirements
Description
AC Mains Wiring
The type of wiring is dependent upon the site requirements:
•
CE (Conformite Europeene) Certified Areas
•
NEC Division 2 or Non-Hazardous Areas
•
Cenelec Zone 1 or Zone 2 Areas
•
Rack Mounting Non-Hazardous Area
The installation should have a power disconnect external to the enclosure.
No voltage dependent selections need to be made on the power supply,
as it has a universal input.
CE Installations
See Page 22, CE Installations.
NEC Div 1, Div 2 or Non
Rated Areas
Use Metal Conduit wiring method.
Conductor type: Power cable sized for circuit protection chosen.
Cenelec Zone 1 or Zone 2
Rated Areas
Use Cable Gland wiring method:
Conductor type: Power cable sized for circuit protection chosen, and
must be shielded.
Non Rated Areas or Rack
Mounting
Use Metal Conduit wiring method.
Conductor type: Power cable sized for circuit protection chosen.
18 • Installation
2000591-001
Site Wiring Requirements, Continued
DataNET Channels
The DataNET channel connections can be either copper wire or fiber
optic cable. The wiring method and cable type for DataNET is dependent
upon the site requirements. For cable requirements see Table 2-1.
Table 2-1.
Recommended DataNET
Cable
The following Table should be used when evaluating or selecting cable
for an existing or new DataNET installation.
Cable Type
Vendors & P/N
Installation Notes
Fiber Optic
SAA P/N 1270002-002
MM 62.5/125; 4 Fiber
Conductors Required
for TX/RX Redundancy
Industry Available from
Multiple Vendors
New Installation as
an alternative to
copper cable
2- Conductor Copper
Wire
SAA P/N 1686002-001
Max distance from
Analyzer to ANG or
between Hubs
1520 meters (5000
ft)
Belden P/N 9182
For
Belden Armored Cable
order
SAA P/N 1680000-002
4-Conductor Copper
Wire
SAA P/N 1681000-003
Belden P/N SSD1743
Recommended for
Single Channel
Max distance from
Analyzer to ANG or
between Hubs
1520 meters (5000
ft)
Recommended for
Dual Channel
Max distance from
Analyzer to ANG or
between Hubs
1520 meters (5000
ft)
2000591-001
Installation • 19
Site Wiring Requirements, Continued
Table 2-1. Recommended
DataNET Cable,
Continued
Cable Type
Vendors & P/N
Installation Notes
Twisted Pair Copper
Wire used in SAA
2100 Installations
SAA P/N C00128
Not Recommended
for New Installations
Belden P/N 9462
Nominal capacitance 155 pF/m (50
pF/ft.)
Max distance from
analyzer to ANG or
between hubs 225
meters (750 ft)
All other Copper Wire
Not Recommended
Customer Responsibility for testing
and conformity requirements
Copper Wire Site
Requirements
The following information pertains when using copper wire
CE Installations
See Page 22, CE Installations.
NEC Div 2 or NonHazardous Rated Areas
Use approved Conduit wiring method. Conduit may contain multiple cables. Adhere to all Federal and local electrical code requirements.
Cable Type: Refer to Table 2-1.
Cenelec Zone 1 or Zone 2
Rated Areas
Use Cable Gland wiring method. Each cable gland allows entry of one
cable.
Cable Type: Recommend Belden 9182 or armored Belden 9182 or
equivalent. The proper cable gland must be used to connect the armor or
shield to the enclosure. Other cables with individually shielded pairs can
be used, but decreased distance is allowed (typically ~800-1000 feet for
22 to 26 AWG low capacitance communication cable ~ 50 to 500 is allowed.
20 • Installation
2000591-001
Site Wiring Requirements, Continued
Non-Hazardous Areas or
Rack Mounting
Use approved flexible non-metallic conduit wiring method. Conduit may
contain multiple cables. For CE installations use only cable gland wiring
method.
Cable Type: Recommend Belden 9182 or equivalent. Other cables with
individually shielded pairs can be used, but decreased distance is allowed
DataNET Channel
Connections
The DataNET channel connections can be either copper wire or fiber
optic cable. The wiring method and cable type for DataNET is dependent
upon the site requirements.
CE Installations
See Page 22, CE Installations
NEC Div 2 or NonHazardous Areas
Use approved Conduit wiring method. Conduit may contain multiple cables. Adhere to all Federal and local electrical code requirements.
Cable Type: Duplex fiber, 62.5/125 micron; see Table 2-1.
Connection: Type ST fiber connectors. Connect these to the appropriate
transmitter and receiver ports for the respective channel.
Cenelec Zone 1 or Zone 2
Rated Areas
Use Cable Gland wiring method. Each cable gland allows entry of one
duplex fiber cable.
Cable Type: Duplex fiber, 62.5/125 micron.
Connections: Type ST fiber connectors. Connect these to the appropriate transmitter and receiver ports for the respective channel.
Non-Hazardous Areas or
Rack Mounting
Use approved flexible non-metallic conduit. Conduit may contain multiple
cables. Conduit may contain multiple. This method is suitable for CE installations.
Cable Type: Duplex fiber, 62.5/125 micron.
Connection: Type ST fiber connectors. Connect these to the appropriate
transmitter and receiver ports for the respective channel.
2000591-001
Installation • 21
CE Installations
Description
This section should be used for installation sites that must conform to CE
(Conformite Europeene) Certification. Typically, this does not apply to
installations outside the EC unless the equipment was purchased with
the explicit requirements and expectations that it shall conform to EC
Electromagnetic and Radio Frequency Interference (EMI/RFI) rejection
specifications.
CE Installation Kit
Available from Siemens Applied Automation CE Installation Kit P/N
2020264-001. This kit has all the parts for all the installations referenced
in this section.
Instructions
The following information pertains to CE Installation of General Purpose,
Zone 1 and Division 2 Equipment. For Zone 1 Installations, all cabling is
terminated in the ANG Zone 1 Enclosure.
Installation with Metallic
Conduit
The preferred method is to route the field wiring in metallic conduit. If
metallic conduit is used, unshielded power and the signal wires can be
used. The power and signal wires (DataNET or Ethernet) must be routed
in separate conduit.
Using flexible conduit and/or armored cable is equivalent to using “steel
conduit”. Flexible conduit or armored cable must have its flexible conduit
and/or armoring conductivity 360-degree terminated at its entry to the
enclosure (or bulkhead).
Installation without
Metallic Conduit
If conduit is not used, the following installation practices must be used to
ensure that the CE certification remains valid:
1. A shielded power cord or cable must be used for the input power
wiring. The shield must be terminated at the unit in a 360-degree
termination at the enclosure (bulkhead); use Siemens Applied Automation P/N 2015729-001 contained in the CE Installation Kit or an
equivalent part. For Zone 1 Installation use Siemens Applied Automation P/N 1311001-014 Installation Kit.
2. The DataNET copper cables shields must be terminated in a 360degree termination at the enclosure (or bulkhead; use Siemens Applied Automation P/N 2015729-001 contained in the CE Installation
Kit or an equivalent part). For Zone 1 Installation, use Siemens Applied Automation P/N 13111001-014 Installation Kit.
22 • Installation
2000591-001
CE Installations, Continued
3. A split ferrite filter must be clamped to DataNET copper wire and
fixed immediately to the outside of the unit; use Siemens Applied
Automation part number 1173000-013 ferrite contained in the CE Installation Kit. This is required to meet the Conducted Immunity requirement for CE/EMC Heavy Industrial. All other CE/EMC Heavy
Industrial requirements are met without the use of a ferrite clamp.
4. Shielded Ethernet cable must be used for all Ethernet connections,
in and outside the GC, and coupled through the enclosure using a
shielded RJ-45 coupler; use Siemens Applied Automation part number 1183200-003 contained in the CE Installation Kit. A mounting
plate (Siemens Applied Automation part number 2020261-001) is
also available to accomplish this. If needed for Zone 1 installation,
Siemens Applied Automation part numbers 2017984-001 and
2017985-001 is available to maintain purge. If a PG gland is used to
make the 360-degree termination of the Ethernet shield at the enclosure, the Installation Kit and other parts are not required.
2000591-001
Installation • 23
Wiring Connections
Description
All input ac power and communications connections are made to connectors located on each of the ANCB modules. To gain access to the
modules, open the front panel of the ANG. For Zone 1 units refer to the
Figure 1-4, Zone 1 Outline Drawing
Figure 2-4. ANCB Module
Advance Data Hiway Port 1 &
DataNET Port 2 Connector
AC Power
Connector
ANCB (Advance
Network
Communications
Board)
I/O Wiring
Power
ON/OFF
Switch
Two removable wiring access plates permit all the wiring to be made
through the bottom section (wall units) or rear section (rack units) of the
ANG. The plates can be punched to accommodate conduit or cable
gland connectors. For Zone 1 units refer to the Figure 1-4, Zone 1 Outline Drawing.
Figure 2-5. Wiring Access
Plate
ACCESS PLATES
Instructions
24 • Installation
IF you are wiring …
AC Power (Mains) Connections
Data Hiway Cable Connections
DataNET Connections
THEN go to …
Page 25
Page 28
Page 31
2000591-001
AC Power (Mains) Connections
ANG Power Supply
Each of the ANCB modules has a power supply assembly. The power
supply can accept inputs from 85-264 VAC, 47-63 Hz without the need
for setting switches or jumpers.
ANCB Module
Advance Data Hiway Port 1 &
DataNET Port 2 Connector
AC Power
Connector
ANCB (Advance
Network
Communications
Board)
Power
ON/OFF
Switch
Installation Note
Depending upon the user configuration the power supplies can be connected in parallel and powered from a single power source or they can
be powered from two independent power sources. In either case disconnects must be provided for each input power source.
Before You Begin
The ANG should be installed in a rack or wall mount; see Wall or Rack
Mounting Installation; page 16. How you route the cable and wire to the
unit is dependent upon the site requirements. See Site Wiring Requirements (page 18) to determine the requirements for your site.
All wiring shall conform to the National Electrical Code (NEC) and/or
other national or local code requirements.
Instructions
2000591-001
Step
Action
1.
Shut off the primary AC Power Supply lines to this location.
2.
Open the door of the ANG by loosening the four captive
screws located on each corner; use a 4mm Allen wrench.
Installation • 25
AC Power (Mains) Connections, Continued
Step
3.
Action
Install 15-Ampere circuit breakers; disconnect switches or
receptacles in the incoming power supply lines or two
switched receptacles near the unit. This will ensure the
power supplies will be completely separated from each of
the power sources. Label the breakers or receptacle boxes
to make sure that the circuits are clearly identifiable.
Note: For one input power sources only a single breaker
box or switch receptacle is required.
4.
Remove the wiring access plates from ANG. Punch holes
as required for either conduit or cable gland connectors for
both power and I/O lines. Install connectors and replace the
plates. For Zone 1 units (Figure 1-4) use one of the pre
tapped holes
Important
If you are going to install a Fiber Optic Coupler Assembly
select the egress locations and punch required holes.
5.
Route input power, in accordance with pertinent electrical
codes and regulations, to ANG. Use entry holes provided in
step (4).
6.
Locate the AC Power Input connector. To make the AC
connections easier the Power Input Connector comes apart.
Simply loosen the two recessed captive screws, grasp the
top portion of the connector and pull it straight out from the
base connector.
Loosen the top wire retaining screws from the removed
connector. Strip the insulation ¼ -inch back from each of the
input power leads. Insert each lead in the correct location,
and tighten down the retaining screws.
26 • Installation
2000591-001
AC Power (Mains) Connections, Continued
Step
7.
Plug the connector back into its base and secure down with
the two recessed captive screws.
8.
If using redundant power supplies repeat steps 6 and 7. If
not, use connecting wires to parallel connect to the other
power supply.
9.
2000591-001
Action
Locate the ANG chassis ground lug
and connect wire
from it to the building’s ground connection.
10.
Inspect all connections for shorts or loose connections.
11.
You are now ready to connect the ADH and DataNET
channels; go to page 31.
Installation • 27
Data Hiway Connections
Description
This section provides instructions for connecting the ANG_DN to an existing Data Hiway.
Figure 2-6. Data
Hiway Connector
The DataNET Gateway unit consists of two ANCB boards. One ANCB
board is configured as the channel A board and the other as the Channel
B board. The ADH Channel is connected to Port 1 while the DataNET
Channel is connected to port 2, see page 48, step 2.
Pin 1
Data Hiway
Port 1 Connections
Pin 1-ADH-A+
Pin 2-ADH-APin 3- Ground
Data Hiway Cable
28 • Installation
The Advance Data Hiway requires a low capacitance, twin axial, 150ohm cable. The cable can be purchased from Siemens Applied Automation. See the table below for ordering the correct cable:
Dual Channel Installation
Standard Oval Cable
Siemens Applied Automation
P/N 1681000-003
(Belden P/N SSD1743)
Dual Channel Installation
Used for larger radius bends
Siemens Applied Automation
P/N 1686002-002
(Alpha P/N 516689)
Single Channel Installation
Siemens Applied Automation
P/N 1686002-001
(Belden 9182, Alpha P/N 9283,
Manhattan P/N 39240)
2000591-001
Data Hiway Connections, Continued
More Information
Instructions
For technical information on the Data Hiway refer to Appendix A in the
Optichrom Advance Library Set, Volume 2, Board Installation and Strapping Manual.
Step
Action
1.
Turn off AC Power (Mains) to the ANG. Turn off AC Power
(Mains) to the ANG.
WARNING
Placing the Power Supply Assembly toggle ON/OFF switch
to OFF does not remove the main voltage to the unit. To
remove all input power to the unit, the external AC Power
(Mains) to the unit needs to be shut off.
2.
Route the Data Hiway cable to the ANG_DN in accordance
with national or local electrical codes and regulations via
the holes drilled in the access plate; see Figure 2-1.
Installation Note
To make the Data Hiway connections easier we have made the Data
Hiway port connector a removable connector. Simply grasp the top portion of the connector and pull it straight out from the base connector.
CAUTION
Do not plug-in the wired Data Hiway connector until you have set the
loop and unit number; see Chapter 3. Data Communications Setup.
2000591-001
3.
Designate which ANCB will be Channel A and which will be
Channel B. We suggest the right module be channel A.
4.
Locate the Channel A, Port 1 connector. To make the connections easier the connector comes apart. Simply loosen
the two recessed captive screws, grasp the top portion of
the connector and pull it straight out from the base connector.
5.
Loosen the top wire retaining screws from the removed
connector. Strip the insulation ¼ -inch back from each of
the connector leads.
Installation • 29
Data Hiway Connections, Continued
Instructions,
continued
Step
Action
6.
Connect the ADH Channel cable to channel A port 1, ADH
+ and - terminals. Connect the ADH Channel B to Port 1 on
the Channel B designated board. Tighten down all the retaining screws.
Pin 1
Data Hiway Port 1
Connections
Pin 1-ADH-A+
Pin 2-ADH-APin 3- Ground
ADH cable shields are grounded at one end only. If ground
is at ANG end, use GND terminal.
30 • Installation
7.
Repeat steps 6 and 7 for Channel B, Port 1 connector.
8.
Perform Data Hiway Post Installation Test; refer to Appendix A. How to Test the Data Hiway.
9.
Remove the ADH plug connector from each ANCB. Do Not
make final connections until you have set the loop and unit
number; see page 47 Setting Network Address & Loop and
Unit Numbers.
10.
You are now ready to make the DataNET connections; go
to page 31.
2000591-001
DataNET Connections
Description
The DataNET ports can accept copper or fiber optic cables. All connections are made to connectors located on each ANCB module.
If the unit is to be installed in an existing Data Hiway installation the existing Data Hiway wiring can be used.
Channel Designation
and IP Address
The ANG enclosure houses two identical ANCB modules. Each ANCB
provides either a channel A or B channel network interface for one Data
Hiway channel and one DataNET channel.
An internal Ethernet cross-link connection via the Ethernet 10Base2
(BNC) port provides the communication link between the two modules.
Cross Link Cable
ANCB
PC COM
Ports
Each module to be configured as Channel A or Channel B
and with different IP Addresses
Instructions
2000591-001
IF you are wiring for …
THEN go to …
DataNET Copper Connections
32
DataNET Fiber Optic Cable Connections
34
Installation • 31
DataNET Copper Connections
Before You Begin
The wiring method (conduit or cable glands) and which cable type you
use is dependent upon the site requirements. Review the Site Wiring
Requirements page 19 to ensure that you are using the correct cable
and wiring method.
Figure 2-7. ANCB Board
Jumper Settings
Refer to ANCB Description page 74.
J 10 Port 1
For ADH: Jumpers on
Top 3 Positions
J11 Port 2
For DataNET:Jumpers on
Bottom 3 positions
Operation LEDS
Config Port
RS232
57.6 KB
Board
RESET
J12
J14
10Base2
10BaseT
J5
Default on Pins 1 &2
•
•
•
•
•
•
J2 Jumper Connections
• 150 Ohm
• 120 Ohm Port 2 (DN)
• 100 Ohm
• 150 Ohm
• 120 Ohm Port 1(DN)
• 100 Ohm
J2 not used for ANG-EN
Instructions
Step
1.
Action
Turn off AC Power (Mains) to the ANG.
WARNING
Placing the Power Supply Assembly toggle ON/OFF switch
to OFF does not remove the main voltage to the unit. To
remove all input power to the unit, the external AC Power
(Mains) to the unit needs to be shut off.
2.
32 • Installation
Route the DataNET copper cable to the ANG in accordance with national or local electrical codes and regulations
via the holes drilled in the access plate; see Figure 2-1.
2000591-001
DataNET Copper Connections, Continued
Installation Note
Instructions,
continued
To make the connections easier we have made the port connector a removable connector. Simply grasp the top portion of the connector and
pull it straight out from the base connector.
Step
Action
3.
Designate which ANCB module will be Channel A and
which will be Channel B. We suggest the right module be
channel A.
4.
Locate the Port 2 connector. To make the connections
easier the connector comes apart. Simply loosen the two
recessed captive screws, grasp the top portion of the connector and pull it straight out from the base connector
Port 2 Pin 1 (+)
DataNET
Port 2 Connections
Pin 4 = +
Pin 5 = Pin 6 = Ground
Important
All DataNET copper connections are made to Port 2. Do
Not make any DataNET copper connections to Port 1.
2000591-001
5.
Loosen the top wire retaining screws from the removed
connector. Strip the insulation ¼ -inch back from each of
the connector leads.
6.
Connect the Channel A, DataNET wires to port 2 terminals.
Repeat for Channel B, DataNET connections. Tighten
down the retaining screws
7.
Plug DataNET cable connectors into their base connectors.
Installation • 33
DataNET Fiber Optic Connections
Description
Required Parts
Fiber Optic Coupler
The Fiber Optic Coupler is mounted in a threaded, potted, gas tight fitting
assembly designed for use in hazadrous areas when properly installed in
a approved enclosure. The ANG_DN uses two Fiber Optic Couplers, one
for Channel A, Port 2 (DataNET Channel A) and one for Channel B, Port
2 (DataNET Channel B).
All mounting hardware is supplied with the DataNET Fiber Optic ANG
parts kit. These parts are also available as spares and can be ordered
from us.
Description
Part Number
Fiber Optic Coupler Assembly
2015828-001
Fiber Optics Coupler Seal Nut
N8005
Fiber Optic Coupler Cable
2020947-001
The DataNET Fiber Optic Coupler performs translation of signals
between a DataNET Hub and a ANG_DN gateway. The Fiber Optic
Coupler converts between electrical signals and optical signals. The
conversion is transparent to the network. Fiber Optic signals are
impervious to distubances caused by electrical interference from nearby
equipment, ground loops, power surges, or nearby lightning strikes.
DataNET Fiber Optics Couplers can drive up to 5000 feet of fiber optic
cable.
34 • Installation
2000591-001
DataNET Fiber Optic Connections, Continued
Figure 2-8. Fiber Optic
Coupler
The DataNET Fiber Optic Couplers use ST-style connectors (twist &
lock). Always insure that the TX (Transmit) on one end of the link is
connected to the RX (Receive) at the other end of the link. Some duplex
fiber optic cables are coded to help monitor the direction of data travel. If
the fibers are not coded, special attention must be paid to insure a
proper connection.
Receive
Darker Gray Color
Pin 5 GND
Transmit
Pin 3 Receive
Pin1 +5V
Pin 2 GND
Pin 4 XMIT
Ping 6 GND
Connector End View
2000591-001
Fiber End View
Installation • 35
DataNET Fiber Optic Connections, Continued
Instructions
Since there is a Fiber Optic Coupler for each channel the following
procedure should be repeated for each channel.
Step
1.
Action
Turn off AC Power (Mains) to the ANG.
WARNING
Placing the Power Supply Assembly toggle ON/OFF switch
to OFF does not remove the main voltage to the unit. To
remove all input power to the unit, the external AC Power
(Mains) to the unit needs to be shut off.
2.
Connect the Fiber Optic cable, 10-pin connector to J12 on
the ANCB.
J12
3.
36 • Installation
Since the DataNET is connected to Port 2 on each ANCB
only the Channel B pair of fiber optic cable is connected to
the Fiber Optic Coupler. Tieback to the cable the 6-pin
connector labeled Channel A. Connect the Channel B cable to the Fiber Optic Coupler.
2000591-001
DataNET Fiber Optic Connections, Continued
Instructions,
continued
Step
Action
4.
Route the other 6-pin connector through the holes drilled in
the access plate and connect to the Fiber Optic Coupler
Assembly.
5.
Through the access plate holes mount the Fiber Optic
Coupler Assembly using the hardware that came with it.
For Zone 1 units (Figure 1-4) mount the assembly through
one of the pre tapped holes.
6.
Connect the Fiber Optic cable transmit and receive lines to
the ST connectors on the assembly; see figure 2-8.
The DataNET Fiber Optic Couplers use ST-style
connectors (twist & lock). Always insure that the TX on one
end of the link is connected to the RX at the other end of
the link. Some duplex fiber optic cables are coded to help
monitor the direction of data travel. If the fibers are not
coded, special attention must be paid to insure a proper
connection.
2000591-001
Installation • 37
Chapter 3
Data Communications Setup
Introduction
Overview
This chapter provides maintenance personnel instructions for configuring
the Advance Network Gateway with DataNET (ANG_DN). Once the operational settings are made the unit will function as a communication
router on an Advance Communication System (ACS) network.
Command Line
Definitions
Review Chapter 4, Command Line Summary. Chapter 4 provides definitions for all of the commands you will be using in this chapter.
Chapter Preview
This chapter provides the following information:
Topic
2000591-001
Page
Configuring Your PC
40
Establishing a Connection
44
Setting Network Address & Loop and Unit Numbers
47
Assigning an IP Address
50
Editing the Address Translation Table
51
Firmware Updates
56
Data Communications Setup • 39
Configuring Your PC
Description
The Advance Network Gateway (ANG) provides a user interface called
CLI (Command Line Interface). Any communication program capable of
VT100 terminal emulation can be used to communicate with the CLI interface. The Windows Hyper Terminal is the recommended communication program.
Baud rate:
Data bits:
Parity:
Stop bits:
Flow control:
Instructions
57.6k baud
8
none
1
none
The following procedure uses the Windows HyperTerminal program, to
connect to the ANG.
1. Click the Start button, and then click on Programs.
2. Click the HyperTerminal icon to start the Program.
Connection Description dialog box will open.
3. In the Name field, type in a Connection Name. Example: Advance
DataNET Gateway.
4. In the Icon field select an Icon to represent the name selected.
40 • Data Communications Setup
2000591-001
Configuring Your PC, Continued
5. Click OK.
The Connect To dialog box opens.
6. From the Connect using scroll list choose the COM port number
you will be using on the PC to connect to the ANG configuration port.
7. Click OK to save the selection.
The COM Properties box opens.
2000591-001
Data Communications Setup • 41
Configuring Your PC, Continued
8. Scroll each field and select the following Port Settings:
Bits per second: 57600
Data Bits: 8
Parity: None
Stop bits: 1
Flow Control: None
9. Click OK.
The Main Menu will appear.
10. Click File and choose Properties from the drop-down menu.
The Advance DataNET Gateway Properties box will appear.
42 • Data Communications Setup
2000591-001
Configuring Your PC, Continued
11. Click Settings tab.
12. From the Emulation scroll list select VT100. Do not change the default settings for the other parameters.
13. Click Terminal Settings button.
The Terminal Settings dialog box will appear.
14. Click OK to accept the default settings.
The Advance Network Gateway Properties box will appear.
15. Click ASCII Setup button.
The ASCII Setup dialog box will appear.
16. Click OK to accept the default settings and return to the Settings
tab.
17. Click OK to return to main menu.
18. Enter the short cut name. Click Save to complete the setup.
Your PC is now setup to connect to and configure the ANG.
To create a shortcut to the new connection you just entered and place it
on your Desktop, select the file name you entered in step 18 and click
the right mouse button. From the pop-up menu select Create Shortcut.
Once the shortcut is created it can be moved to the Desktop. Simply click
the shortcut icon and drag the icon while holding down the left mouse
button. Release the mouse button to place the icon.
2000591-001
Data Communications Setup • 43
Establishing a Connection
Description
Once your PC is set up, as described in Configuring Your PC, you are
ready to connect to and configure the ANG_DN.
Getting Started
… read through this Chapter prior to performing any procedures.
Dual System
The unit is a fully redundant unit with dual advance network communications boards (ANCB) and power supplies. Each half is assigned a channel designation (A or B) and an IP Address.
Cross Link Cable
ANCB
PC COM
Ports
Each half to be configured as Channel A or Channel B
Before You Begin
1. Connect a standard 9-pin COM cable from the designated PC COM
port (Figure 2-7) to RS232 Configuration Port located on etiher
ANCB.
2. Turn on the AC power to the ANG.
Password Protection
The user interface program is password protected. This insures the data
integrity of all configuration data and limits unwanted access of the
User’s network. To access any of the programs you must logon with the
correct password.
44 • Data Communications Setup
2000591-001
Establishing a Connection, Continued
Password Format
A password name can consist of any combination of alphanumeric characters. The alphanumeric name must have a minimum of five and a
maximum of twenty characters. The ANCB is shipped from the factory
with the word “password” entered as the default password name.
How to Change
Password
The user can change the password name at any time. To do this login
using the current password then type: “password stand stand”. Where
the word stand is your new password entered twice to verify that it was
properly entered.
How to Log Out
You may log out or close the Configuration and Diagnostic program at
any time by typing logout. However, the Configuration and Diagnostic
program will automatically log you out after five minutes.
How to Log On
The following procedure assumes that the HyperTerminal program, residing on your PC has been configured to communicate with the ANG
and the PC is connected to the ANCB Configuration Port.
1. Open Windows HyperTerminal program.
2. Press ↵ Enter twice
The following dialog box appears:
2000591-001
Data Communications Setup • 45
Establishing a Connection, Continued
3. At the > prompt type: login password and press ↵ Enter.
The Connect Screen will appear with the login information and the
local prompt. The local prompt indicates that you are communicating
with the ANG connected directly to the PC.
You are now ready to configure the ANG, go to page 47.
Remote Connection
Log On
If your PC is connected to one of the ANG configuration ports you can
connect to any other hub on the same network if you know the IP address of the ANG.
1. Open Windows HyperTerminal program on your PC.
2. Press ↵ Enter twice, the Command Request dialog box will appear.
3. At the > prompt type: login password [IP Address].
Once the password is verified the system responds with the login information and displays the remote prompt which includes the IP address of
the connected ANG.
46 • Data Communications Setup
2000591-001
Setting Network Address & Loop and Unit Numbers
Description
This section provides instructions to configure an Advance Network
Gateway DataNET (ANG) with a network address. There are 4 levels of
addressing that must be set on each ANCB:
1. A factory set Ethernet address.
2. An assigned IP address for each ANCB board using a common Subnet-mask.
3. An assigned DataNET address that must be the same for both
ANCB board half.
4. An assigned Advance Data Hiway loop and unit address that must
be the same for both ANCB board half.
Before You Begin
1. Connect a standard 9-pin COM cable from the designated PC COM
(see Figure 2-7) to one of the ANCB Configuration Ports.
2. Open Windows HyperTerminal program on your PC; reference Configuring Your PC, page 40.
3. Connect and Log on to DNH; reference Establishing a Connection,
page 44.
Command Line
Definitions
Chapter 4, Command Line Summary, provides definitions for all of the
commands you will be using in this chapter.
Instructions
1. Log on locally to the ANG.
The Connect Screen will appear with the login information and the
local prompt. The local prompt indicates that your are communicating
with the ANG connected directly to the PC.
2000591-001
Data Communications Setup • 47
Setting Network Address & Loop and Unit Numbers, Continued
Learning Hint
Parameters are temporarily saved in RAM after being entered. However,
parameters are not saved into long term storage (Flash) until you type
‘reset’.
2. Designate the ANCB you are connected to as Channel A, at the Local > prompt type: config channel
3. To configure the ANG_DN IP address, at the Local > prompt type:
config address ip xxx.xxx.xxx.xxx
Where xxx.xxx.xxx.xxx should be replaced with the 12 digit unique
network address. See Assigning an IP (Internet Protocol) Address
page 50.
4. Press ↵ Enter.
5. To save your entry, at the Local > prompt type: reset
6. To configure the ANG_DN subnetmask, at the local > prompt type:
config netmask xxx.xxx.xxx.xxx
Where xxx.xxx.xxx.xxx is the subnet mask for your network. Typically, this would be 255.255.0.0 or 255.255.255.0.
7. To configure the device id, at the Local > prompt type: config device
id xxx.xxx.xxx.xxx
8. Where xxx.xxx.xxx.xxx is typically the IP Address of Hub ‘A’.
9. Press ↵ Enter.
10. Press ↵ Enter, and save your entry by typing at the local > prompt:
reset.
11. To configure the ANG_DN Loop number, at the local > prompt type:
config loop x
12. Where x is a number in the range from 1 - 8 depending on the ADH
Loop number of the Units to be connected directly to the ANG_EN
ADH bus.
13. Press ↵ Enter, and save your entry by typing at the local > prompt:
reset
48 • Data Communications Setup
2000591-001
Setting Network Address & Loop and Unit Numbers, Continued
Learning Hint
Parameters are temporarily saved in RAM after being entered. However,
parameters are not saved into long term storage (Flash) until you type
‘reset’.
2. Designate the ANCB you are connected to as Channel A, at the Local > prompt type: config channel
3. To configure the ANG_DN IP address, at the Local > prompt type:
config address ip xxx.xxx.xxx.xxx
Where xxx.xxx.xxx.xxx should be replaced with the 12 digit unique
network address. See Assigning an IP (Internet Protocol) Address
page 50.
4. Press ↵ Enter.
5. To save your entry, at the Local > prompt type: reset
6. To configure the ANG_DN subnetmask, at the local > prompt type:
config netmask xxx.xxx.xxx.xxx
Where xxx.xxx.xxx.xxx is the subnet mask for your network. Typically, this would be 255.255.0.0 or 255.255.255.0.
7. To configure the device id, at the Local > prompt type: config device
id xxx.xxx.xxx.xxx
8. Where xxx.xxx.xxx.xxx is typically the IP Address of Hub ‘A’.
9. Press ↵ Enter.
10. Press ↵ Enter, and save your entry by typing at the local > prompt:
reset.
11. To configure the ANG_DN Loop number, at the local > prompt type:
config loop x
12. Where x is a number in the range from 1 - 8 depending on the ADH
Loop number of the Units to be connected directly to the ANG_EN
ADH bus.
13. Press ↵ Enter, and save your entry by typing at the local > prompt:
reset
48 • Data Communications Setup
2000591-001
Assigning an IP Address
Overview
Each Advance Network Gateway (ANG) unit on a network must be assigned an IP address. This 32-bit number defines each unit’s network ID
and host ID. The user assigns the IP address before the unit is physically
connected to a network.
See Setting Network Address & Loop and Unit Numbers, for instructions
on how to enter the IP address.
IP Address
The IP Address consists of a 32-bit number divided into four 8-bit fields.
Each field is expressed as a decimal number from 1 to 255 with each
field separated by periods. This is referred to as “dotted decimal” notation. For example, 192.16.9.52 is an IP address.
How to Assign an IP
Address
Ask your network administrator to assign you an IP Address, or if the
ANG will be in a closed plant area and not connected to the Internet
(World Wide Web) you can select an address from Table 3-1.
See Setting Network Address & Loop and Unit Numbers, for instructions
on how to enter the IP address.
Table 3-1. Available IP
Addresses
192.165.0.1
192.165.0.2
192.165.0.3
192.165.0.4
192.165.0.5
192.165.0.6
192.165.0.7
192.165.0.8
192.165.0.9
192.165.0.10
192.165.0.11
192.165.0.12
192.165.0.13
192.165.0.14
50 • Data Communications Setup
192.165.0.15
192.165.0.16
192.165.0.17
192.165.0.18
192.165.0.19
- 192.165.0.254
- 192.165.1.254
- 192.165.2.254
192.165.3.1 - 192.165.3.254
2000591-001
Editing the Address Translation Table
Overview
The Advance Network Gateway (ANG) monitors the “local” ADH bus for
messages with a “remote” destination address. The ANG determines if
the message destination is “remote” by searching it’s Address
Translation Table (ATT). If the destination address is located remotely,
the ANG_DN encapsulates the ADH message within the data portion of
an IP packet and sends the message out the Ethernet port.
Table Description
The Address Translation Table (ATT) records all known units that reside
on the Advance Data Hiway (ADH). Each record within the ATT contains
an ADH Loop / Unit number and the IP address of the ANG the unit is
directly connected to. The ATT records are automatically added or
updated each time an ADH broadcast is received. Each ANG broadcasts
it’s ATT every 10 minutes. This insures the data intgerity of all ATT
tables. An uninitalized ATT is automatically updated after 10 minutes by
receiving ADH broadcasts and ANG_DN ATT broadcasts.
Important
Only Advance analyzer units broadcast on a periodic basis so it may be
necessary to add other type units when a new ANG is added. An
alternate method of updating the ATT is to force all ADH units to send a
power-up broadcast by pressing the reset button or cycling the power.
Before You Begin
The following procedure assumes that the Windows Hyper Terminal program residing on your PC has been configured, the ANG_DN is operational and the PC is connected to the ANG_DN.
Important DataNET
Gateway Users
If you are editing the translation tables for an Advance Network Gateway
DataNET always disconnect the crossover link cable that connects the
two ANCB's before editing any tables. Remember that if you edit the
channel A designated ANCB, you must also edit the assigned channel B
ANCB.
2000591-001
Data Communications Setup • 51
Editing the Address Translation Table, Continued
Displaying the ATT
The Address Translation Table (ATT) can be displayed using the
Configuration Management routines.
1. Connect a standard 9-pin COM cable from the designated PC COM
(see Figure 2-7) to the Channel A ANCB Configuration Ports.
2. Open Windows HyperTerminal program on your PC; reference Configuring Your PC, page 40.
3. Connect and Log on to ANG; reference Establishing a Connection,
page 44.
4. To display the entire ATT type at the Local > prompt: display all
52 • Data Communications Setup
2000591-001
Editing the Address Translation Table, Continued
5. To display a single Loop only type: display adh x
Where x is the ADH Loop number. Allowable values are 1 - 8. If you
leave off the x value then the Loop number will default to the Loop
number of the local ANG_EN.
6. To display the ATT by IP number type: display ip xxx.xxx.xxx.xxx
Where xxx.xxx.xxx.xxx is the IP address. If you leave off the IP address, the IP portion will default to the value of the local ANG_DN.
Note: 255.255.255.255 and 0.0.0.0 are not allowed.
2000591-001
Data Communications Setup • 53
Editing the Address Translation Table, Continued
Editing the ATT
1. To delete a single entry from the ATT type: del adh loop unit
Where loop is the ADH loop number (1 - 8) and unit is the ADH unit
number (1-31).
All parameters must be specified.
2. To delete all ATT entries associated with a single IP address type:
del ip xxx.xxx.xxx.xxx
Where xxx.xxx.xxx.xxx is the IP address in dotted decimal notation.
Note: 255.255.255.255 and 0.0.0.0 are not allowed.
54 • Data Communications Setup
2000591-001
Editing the Address Translation Table, Continued
3. To delete all entries in the ATT type: delete all
4. To add entries to the ATT type: add adh loop unit
Where loop is the ADH loop number (1 - 8) and unit is the ADH unit
number (1-31).
All parameters must be specified.
You can only add entries that are local to the ANG_DN. If it is not directly connected to the ADH terminals you cannot edit it.
2000591-001
Data Communications Setup • 55
Firmware Updates
Description
Periodically we will provide our ANG users with firmware upgrades. Perform the following instructions to download a new ANG firmware upgrade
to the ANCB board. A firmware upgrade will take approximately 5 minutes depending upon the speed of your PC hardware.
Instructions
The following procedure assumes that the Windows Hyper Terminal program residing on your PC has been configured, the ANG is operational
and the PC is connected to the ANG.
1. Log on to the ANG.
2. At the > prompt type: download
You should see the following response on the screen. At this point
the ANCB is ready to receive the new firmware version.
3. From the Main Menu bar click on Transfer.
56 • Data Communications Setup
2000591-001
Firmware Updates, Continued
4. Click on Send Text File.
The Send Text File dialog box will appear.
5. Under Files of type select All files (*.*).
6. Under File name type in the upgrade version file name
(ANG_DNCP.MOT).
This will start the down loading of the files. Once the download has
begun the block numbers will be displayed as they are transmitted.
The upload will take approximately 45 minutes to complete.
2000591-001
Data Communications Setup • 57
Chapter 4
Command Summary
Introduction
Overview
This chapter is intended for maintenance personnel.
This chapter provides a description of the commands used for setting up
the data communications and for performing diagnostic tests. Refer to
Chapter 3. Data Communications Setup
2000591-001
Config address ip ipaddr
Set the ANG_DN IP address.
config address ethernet eaddr
Set the ANG_DN Ethernet hardware address.
config channel (A or B)
Set the ANG_DN channel number.
config device id
xxx.xxx.xxx.xxx
Set the ANG_DN device id.
config display
Display the current ANCB non-volatile
parameters.
config loop
Set the ADH Loop number.
config netmask
xxx.xxx.xxx.xxx
Set the ANG/DN IP subnetwork mask.
config iproute routeaddr
Set the default router IP address.
config time server ip
xxx.xxx.xxx.xxx
Set the time server IP address.
config unit
Set the ADH Unit number.
date
Display time and date.
date yyyymmddhhmm
Set time and date.
display links
Display link state table.
dn setuptime
Display and/or change the DN setuptime
in microseconds.
dn window
Display and/or change the DN window.
download
Download new software via Configuration port.
LIST
List next 22 log events.
list nnn
List 22 events, starting with number nnn.
list nnn, xxx
List xxx events, starting with number
nnn.
list on
Continuously list events from the log
buffer, as they are added (terminate by
pressing any key).
Command Summary • 59
Command Summary, Continued
60 • Command Summary
list clear
Clear all events from log buffer.
login password
Log in to device via Configuration port.
login password remoteaddr
Log in to remote device (ANCB or HUB).
logout
Log out of device.
netstat dn
Display DataNET link statistics for all ports.
netstat dn clear
Display and clear all DataNET link statistics
for all ports.
netstat dn port# clear
Display and clear DataNET link statistics for
the specified port (1 or 2).
netstat dn port#
Display DataNET link statistics for the
specified port (1 or 2).
netstat net
Display network statistics for Ethernet port.
netstat clear
Clears the Ethernet statistics counters.
netstat pna
Display OS memory buffer statistics.
password newword newword
Change login password for ANCB.
port start port#
Enable specified DataNET port (2).
port stop port#
Disable (stop all activity) on specified DataNET port (2).
reset
Reset and Save Configuration data.
test port#
Put a port into hardware test mode.
test off
Take a port out of test mode.
timeout on
Enable user login timeout.
timeout off
Disable user login timeout.
Validation
Display the current link validation timeout
value.
Validation timeout
Set a new link validation timeout value.
2000591-001
Command Summary, Continued
add adh
This command adds a “local” ADH device to the Address Translation
Table. The Address Translation Table translates ADH addresses (Loop
& Unit) into IP addresses. “Local” indicates the ADH device is connected
directly to the Gateway’s ADH data bus.
add adh 1 5
This command adds ADH device Loop#1, Unit#5 to the Address Translation Table under the IP address of the Gateway.
config address ip
This command sets the device IP address. Each device in the system
must have a unique IP address. Your TCP/IP network administrator can
help you choose appropriate addresses for your network. IP addresses
are entered in “dotted-decimal” notation. For example:
config address ip 192.10.6.123
The IP address is not automatically stored in non-volatile memory until
the reset command is entered. You can display the current IP address
with the config display command.
config display
This command displays the configuration parameters for the device.
config netmask
This command sets the IP subnet mask for the device. Your TCP/IP network administrator can help you choose appropriate subnet mask for
your network. Subnet masks are entered in “dotted-decimal” notation.
For example:
config netmask 255.255.192.0
The subnet mask is not automatically stored in non-volatile memory until
the reset command is entered. You can display the current subnet mask
with the config display command.
2000591-001
Command Summary • 61
Command Summary, Continued
config iproute
This command sets the address of the IP router to which the device
should send TCP/IP messages whose destinations do not reside on the
devices’ own network. Your TCP/IP network administrator can help you
choose appropriate router addresses for your DataNET hubs (a router
address is not required). Addresses are entered in “dotted-decimal” notation. For example:
config iproute 192.10.6.1
or to disable the router
config iproute 0.0.00
config time server ip
This command sets the IP address of the device used as a time server.
The ANCB date and time is NOT battery backed up and requires resetting each time the power is lost or the board is reset. If a time server is
specified the ANCB will request the time at powerup and periodically
every 24 hours. The ANCB requests the time from the time server IP on
TCP port #13. The returned value must be in the form “Mon Sep 21
13:24:11 1999”. A MAXUM analyzer or NAU can be configured to provide the time server function. Addresses are entered in “dotted-decimal”
notation. Example:
time server ip 127.3.14.12
Entering all zeroes for the timer server address will disable the time
server function.
time server ip 0.0.0.0
date
Without an input argument, date displays the current date and time, as
known by the ANCB. Otherwise, date sets the ANCB’s current date and
time according to the input argument. The date command has the following form:
date yyyymmddhhmm
The argument part yyyy is the four digits of the year; the first mm is the
month number; dd is the day number in the month; hh is the hour number (24 hour system); the second mm is the minute number; and .ss
(optional) specifies seconds.
For example, to set the date to Oct 8, 2001 12:45 AM, type
date 200110080045
62 • Command Summary
2000591-001
Command Summary, Continued
The ANCB clock is not battery backed up. This means the date must be
set every time the ANCB is reset or the power is removed. If the ANCB is
connected to a network with a timeserver the ANCB can be configured to
request the time at power up and every 24 hours thereafter. Refer to the
config timeserver ip command.
Note
A MAXUM analyzer or NAU can be configured to provide the time server
function.
display links
This command displays the ANG_DN link state table. The link state table
indicates, for each link, whether or not the link is currently “up,” “down,”
or undergoing link validation (“check”). For DataNET links, the table also
gives the device to which the link connects. Devices are identified by IP
address. For example:
local> display links
Port:
Medium:
1
ADH Copper
2
DN Copper
Ethernet
“dn” Command
Status:
Connected
Connected
Offline
Connected to:
ADH Channel B
DN Channel B
This command may be used to override default values for several parameters related to the DataNET protocol. Specific forms of the command are:
dn setuptime
Displays the current “setup time” value, in
microseconds. This is the time that the
ANCB_DN board will transmit a “preamble” pattern on a DataNET link before
starting the actual data frame. The preamble allows time for the receiver circuitry
at the far end of the link to adjust to the
incoming signal’s amplitude, phase, and
frequency. The default setup time is 3.5
milliseconds.
dn setuptime time
Sets the DataNET setup time to the value
given, in microseconds. The new setup
time value is saved in non-volatile memory.
Time is entered in microseconds. Example: 3.5 milliseconds is entered as 35000.
2000591-001
Command Summary • 63
Command Summary, Continued
download
dn window
Displays the transmit “window” size used
by DataNET. This is the number of Iframes (Information frame) that a station
may send before it must receive a low-level
acknowledgment from the receiving station.
dn window num
Sets the transmit window used by ports 1
and 2 on the ANCB. The parameter “num”
must be a number 1 through 7. The default
window size is 7.
Use this command to load new software into the device via the RS-232
Configuration port. The procedure for software download is:
1. Make sure you have a “ANG_DNCP.mot” file available for download.
2. Log into the target ANG_DN board through the RS-232 port, using
HyperTerm.
3. Type “download” at the prompt (“>”). The device will print some messages and then prompt to begin transmitting the download file.
4. Transmit the download file. Use the HyperTerm “Transfer --> Send
Text File…” command. Find the “ANG_DNCP.MOT” file using the
browser window. You will have to select “Show all files” in the “Files
of type” window to see the “ANG_DNCP.MOT” file.
5. After you have selected the “ANG_DNCP.MOT” file and click on
“OK,” HyperTerm will begin transmitting records to the Hub. The Hub
will respond by periodically displaying addresses as the file downloads.
6. After about 4 minutes 30 seconds, the download will be complete.
The hub will then display messages indicating that the download has
completed, and it is erasing and programming the FLASH memory.
7. Finally, the Hub will reset, and display a new login prompt.
64 • Command Summary
2000591-001
Command Summary, Continued
Enter the list command at any time from the Configuration Management
interface to see event buffer messages. The list command has an internal current sequence number that is set to 1 each time a Configuration
Management login occurs. The list command will show 10 messages
each time it is entered, beginning with the current sequence number. The
current sequence number is updated each time list is used. A new current sequence number can be entered with the list command:
list
local>
msg |
155 |
156 |
157 |
158 |
159 |
160 |
161 |
list 155
source
|
destination
Trace enabled
IP-172.16.9.211
| IP-172.16.9.210
IP-172.16.9.211
| IP-172.16.9.210
IP-172.16.9.210
| IP-172.16.9.211
IP-172.16.9.211
| IP-172.16.9.210
Station detected IP-172.16.9.014
IP-172.16.9.014
| IP-172.16.9.210
162 | IP-172.16.9.211
163 | IP-172.16.9.210
164 | IP-172.16.9.211
| IP-172.16.9.210
| IP-172.16.9.211
| IP-172.16.9.210
| size | source port |
|
|
64 | 2
|
|
64 | 2
|
|
64 | Ethernet
|
|
64 | 2
|
|
| 1536 | 5
|
| 1536 | 2
| 1132 | Ethernet
|
64 | 2
time stamp
00:01:48.23
00:01:48.29
00:01:49.00
00:01:49.75
00:01:50.11
00:02:00.00
00:02:18.29
| 00:02:18.00
| 00:02:19.75
| 00:02:20.11
The event display gives a time-stamp, and an event description. All
events other than frame-capture events are always shown as single
lines. Captured frames may be summarized as single lines, or expanded
into a multi-line display.
Time stamps are shown as elapsed time from the last board reset or
power-on.
The user can view more than 22 messages by supplying a sequence
number and list length:
list 1, 300
List message numbers 1 – 300.
The list length may appear by itself:
list , 32
This lists the next 32 trace buffer entries, and increments the current
message number by 32.
All the messages in the internal trace buffer can be viewed by listing sequence number one then entering the list command until the last message is displayed. When the current message number is incremented to
the last message in the internal buffer, it is automatically set to 1.
2000591-001
Command Summary • 65
Command Summary, Continued
There is a continuous listing mode for monitoring all the messages in the
internal trace buffer. It is set by entering list on. All the messages in the
internal buffer will be displayed and any new messages will be listed as
soon as they are collected into the buffer. The continuous listing mode is
terminated by pressing any key.
To clear all events from the event buffer, use
list clear
login
The login command allows the user to access all the ANCB parameters
and diagnostic information. The format is:
login password
Where password is the user password.
A password can contain any alphanumeric character and must be between 5 and 20 characters in length. See the password command for
information on how to change the user password.
Users can login to a remote ANCB or DataNET HUB by first logging out
of the local device and then typing:
login password xxx.xxx.xxx.xxx
logout
66 • Command Summary
Where xxx.xxx.xxx.xxx is the IP
address of the remote device.
The logout command is used to log the user out of either the local or remote device. Note: User’s will be automatically logged out after five minutes of non-activity unless the user has issued the timeout off command. Also the user must be logout of the local device before logging
into a remote device. See the login command.
2000591-001
Command Summary, Continued
netstat
This command is used to display statistics for the DataNET, Ethernet, or
OS memory buffers.
The command netstat dn displays the total statistics for all DataNET
ports.
The command netstat dn 1 displays the statistics for DataNET port one
only.
Example:
local> netstat dn 1
DataNET Statistics for DN link 1
Frames Sent
Frames Sent/Retried
Frames Sent/Redirected
Frames Sent w/ Errors
Frames Sent UnACKnowledged
Frames Received
Frames Receiver Not Ready
Frames Received w/ Errors
Link down
855
0
0
0
0
859
0
0
2
The command netstat dn clear resets all DataNET statistics counters.
The command netstat dn 2 clear resets only the port 2 statistics counters.
The command netstat net displays the Ethernet statistics for TCP, UDP,
and the Ethernet Interface.
TCP Statistics
Segments Received
Segments Sent
Current Connections
Connections Reset
Failed Connections
Segments Retransmitted
UDP Statistics
Datagrams Received
Datagrams Sent
Receive Errors
Unknown Ports
2000591-001
12
12
0
0
0
0
991
991
0
0
Command Summary • 67
Command Summary, Continued
Interface Statistics
Bytes
Unicast packets
Non-unicast packets
Discards
Errors
Unknown protocols
Received
1040
0
10
0
0
0
Sent
980568
31
5
0
0
The command netstat clear resets the Ethernet statistics counters.
password
The password command is used to change the user assigned password.
The password can be any alphanumeric character and it must be between five and twenty characters in length. Example:
password newpassword newpassword
Note the newpassword is entered twice to verify that the password was
entered correctly.
“port” Command
This command will enable or disable normal DataNET communication on
individual ports. Before placing a port into “test” mode (see test command below), the port must first be taken offline with:
port stop num
where num is a port number, 1 through 2.
port start num
Will re-start normal DataNET communications on a port.
reset
68 • Command Summary
This command resets and saves the configuration parameters in nonvolatile memory.
2000591-001
Command Summary, Continued
test
This command places a selected port into a hardware diagnostic mode.
The test mode can be used to verify cable continuity and DataNET signal
levels when used in conjunction with an Oscilloscope or other test device.
The command:
test 1
places port 1 into test mode. The device will generate poll messages on
port 1 every 50 milliseconds. The other port continues to operate normally. The command:
test off
turns off test mode. Only one port at a time may be in test mode.
timeout
2000591-001
This command may be used to disable the user login timeout. Normally,
if a user has not issued a CLI command for five minutes, the device will
automatically shut down the user’s login session. This command may be
used to defeat (and re-enable) this timeout:
timeout off
Disables timeout. The device will not automatically
log out the user, regardless of the time elapsed since
the user last issued a CLI command.
timeout on
Re-enables the five-minute CLI timer.
Command Summary • 69
Command Summary, Continued
trace
The trace command controls the device’s frame tracing function. This
feature captures network messages sent and received by the ANCB’s
event buffer. The trace command controls which messages are captured
in the event buffer.
Trace messages may be collected for the Ethernet port or either DataNET port. Trace data may be filtered to collect only input frames, output
frames, or data frames (excluding protocol-only frames such as
poll/acknowledge). The device will not capture any frames until the “trace
on” command is given. Before issuing “trace on,” the user can set up
trace filtering as described below. By default, tracing is set up for all
frames on the Ethernet port.
To set up tracing, the trace command is followed by a list of ports and a
filter mode. The port list is a comma separated list, which may include
any of the following ports:
“1” or “2”
Specifies DataNET port 1 or 2
Port 1 is DataNET Channel A
Port 2 is DataNET Channel B
ethernet
Specifies the Ethernet port
The filter specification may be one of:
data
input
output
all
Trace all data frames (i.e., exclude frames
that do not carry encapsulated Ethernet data).
Trace only input data frames.
Trace only output data frames
Trace all frames, including “protocol-only”
frames on DataNET links.
The port and filter options may be commanded separately or combined
into a single command. The following command sets up tracing for all
frames on the Ethernet link:
trace ethernet all
The following command sets up tracing on port 2, Channel B, for input
data only.
trace 2 input
70 • Command Summary
2000591-001
Command Summary, Continued
The filter may also specify frames for a specific device by declaring the
device IP address. The device filter cannot be combined with the port
specification in a single command. To collect data from or to a device the
commands would look like:
trace 1
trace 172.16.9.201
trace on
- Trace port # 1
- Show messages from device 172.16.9.201
only
- Enable tracing
The first command specifies the port #1 for trace data. The second
command filters the trace data to a single device’s frames, and the third
command enables tracing.
Finally, the trace parameters may be reset to their default values (tracing
all frames on the Ethernet port, without any address filtering) with:
trace reset
Validation timeout
This command sets the time, in seconds, that the device will wait for the
“link validation” diagnostics to complete.
Validation timeout
Validation timeout 10
2000591-001
With no parameters, the command displays the current link validation timeout
setting.
Allows 10 seconds for the link diagnostics to complete.
Command Summary • 71
Chapter 5
Troubleshooting
Introduction
Overview
This chapter provides installation personnel with troubleshooting information to solve problems associated in the setup of the Advance Network Gateway.
Chapter Highlights
Before beginning the installation process read through this Chapter to
familiarize yourself with the information provides.
Topic
2000591-001
See Page
ANCB Description
74
ANCB’s Leds Description and Operation
76
DataNET Troubleshooting Guide
79
Obtaining Diagnostic Information
82
Troubleshooting • 73
ANCB Description
Description
Figure 3-1. ANCB Board
The ANCB (Advance Network Communication Board) is the communications electronics for the unit. The ANCB plugs into the PCI slot located
on the power supply assembly. A bracket fastens it to the chassis. See
Figure 2-4 Power Supply/ANCB Assembly.
J 10 Port 1
For ADH: Jumpers on
Top 3 Positions
J11 Port 2
For DataNET:Jumpers on
Bottom 3 positions
Operation LEDS
Config Port
RS232
57.6 KB
Board
RESET
J12
J4
10Base2
10BaseT
J5
Default on Pins 1 &2
•
•
•
•
•
•
J2 Jumper Connections
• 150 Ohm
• 120 Ohm Port 2 (DN)
• 100 Ohm
• 150 Ohm
• 120 Ohm Port 1(DN)
• 100 Ohm
J2 not used for ANG-EN
J10 &J11
Connections
Jumpers J10 & J11 select the ANG_DN network interface provided to
connector J4.
J10 connects Port1 (pins 1-3) on J4 to one of the Optichrom Data Hiway
(DH) Channels. or Advance DataNET Channel A interface. J11 connects
Port 2 (pins 4-6) on J4 to one of the Advance DataNET Channels.
74 • Troubleshooting
2000591-001
ANCB Description, Continued
Jumper J2 Settings
Jumper J2 is a six-position header used to select the proper cable impedance matching circuit for each ANCB DataNET port. Jumper J2 is
logically partitioned into two groups of three positions, see Figure 3-1.
There are two jumpers provided on J2. The lower jumper configures
Port1 and the upper configures Port2. Each jumper can be placed in one
of three positions, see Figure 3-1. The three positions match cable impedance of 100, 120, and 150 ohms. If the characteristics of the cable
you are using are unknown check with the cable manufacturer for the
resistance setting. The manufacturer’s name is usually printed on the
cable cover. The Optichrom Data Hiway cable requires the 150-ohm setting.
Jumper J5 Setting
The ANG/DN consists of two ANCB boards. Each board provides either
the A or B channel network interface for one Data Hiway and one DataNET channel. Communications between the two boards is via the
Ethernet 10Base2(BNC) port. Jumper J5 selects the termination resistor
used for the 10Base2 port. Place the jumper on J5 between pins 1&2.
The pins farthest away from the 10Base2 connector (see Figure 3-1).
This selects the 50-Ohm termination resistor. The termination resistor
provides the proper end point termination resistance so that an external
termination resistor is not required.
More Information
See ANCB LEDs Description and Operation, page 76.
2000591-001
Troubleshooting • 75
ANCB LEDs Description and Operation
Description
This section provides maintenance personnel with information on how to
use the ANCB LEDs for troubleshooting the Advance Network Gateway
(ANG_DN).
Communications
Board LEDs
Refer to Figure 3-2 for LED position and labeling.
Power-UP
At power-up the top row of LED indicators will blink on briefly as the
board passes it’s various power-up sequence tests. The ADHA green
light indicates that the initial program parameters were successfully
moved from FLASH to RAM memory. The ADHA yellow LED indicates
that the board has passed it’s power-up RAM test, the ADHA red LED
indicates that the board has passed it’s power-up FLASH integrity test,
and the ADHB green LED indicates the board has begun it’s normal program execution. After approximately 5 seconds the indicators will go off
depending upon the current board conditions.
Normal Operation
In normal board operation the ADHA LED’s are used to indicate the
status of the Data Hiway channel and the DNETB LED’s indicate the
status of the DataNET channel. In normal operation the ADHA green
LED blinks to indicate either transmit or receive activity has occurred on
the Data Hiway channel. The yellow LED will blink to indicate any transmit or receive errors that have occurred.
The DNETB LED’s provide a link status indication for the DataNET
channel. If the DataNET link is up and communicating the DNETB green
LED will be lit. If the link is down or in the process of establishing a connection the DNETB red LED will be lit.
The ANG_DN uses the Ethernet 10Base2 port as a cross-link for interboard communications between the two data channels (A&B).
Whenever a communication failure is detected on the cross-link the
ADHB yellow and red LED’s are ON. If the communication link is working
properly the ADHB yellow and red LED’s are OFF.
Board Fault Indicators
76 • Troubleshooting
If the ANG/DN board has a power-up failure or other catastrophic failure
during normal operation the red Fault LED will light to indicate that a fault
has occurred and the yellow LED will blink an error code, see Table 3-1
Error Codes.
2000591-001
ANCB LEDs Description and Operations, Continued
Figure 3-2. ANG_DN LED
Indicators
Figure 3-2 shows the edge visible LEDs on the ANCB. The LED labels
are silk screened adjacent to each LED on the ANCB.
CL
Table 3-1. Error Codes -
Use the following Table 3-1 to determine the error condition. FAULT errors can only be cleared with a board reset.
NUMBER
of Blinks
2000591-001
Type of Error
Corrective Action
1
RAM FAILURE
Replace Board
2
FLASH FAILURE
Reload Firmware or Replace Board
3
ETHERNET FAILURE
Replace Board
4
DataNET FAILURE
Replace Board
6
DUPLICATE IP
Change Board IP address
8
WRONG LOOP
Change Loop Number
9
WRONG JUMPER
CONFIGURATION
Check J10 and J11 Connections
10
DUPLICATE UNIT NUMBER
Change Unit Number
11
INVALID or INCORRECT
CONFIGURATION
Verify and Edit the Configuration parameters for
ANG_DN
Troubleshooting • 77
ANCB LEDs Description and Operations, Continued
ANCB Ethernet
Controller LEDs
Each ANCB provides two Ethernet ports a 10BaseT and 10Base2. Each
port is connected directly to an onboard Ethernet hub. The three LED’s
labeled HUB in figure 3-2 (CL, BNC,TP) are the status indicators for this
internal hub. The Hub LED’s are bi-colored LED’s and require careful
observation of both the color and blink rate to determine the device
status. Table 3-1 describes the color and blink rate to determine device
and port status.
The on-board Ethernet controller provides four status LED’s in Figure
3-2. (Tx, Rx, CL, JAB) The Green TX LED blinks whenever a message is
transmitted on the Ethernet channel. The Green RX LED blinks whenever a message is received on the Ethernet channel. The Red CL LED
indicates there was a collision on the Ethernet. Note: collisions are a
normal occurrence on an Ethernet network. However, excessive collision’s can be indication of a potential problem on the Ethernet. The Red
JAB LED indicates that the Ethernet controller has determined that the
transmitter has remained on for longer than allowed and indicates a possible hardware failure.
10BaseT/10Base2
Ethernet LED
78 • Troubleshooting
CL
Steady Green indicates a FIFO error
Steady Red indicates a Collision on the HUB ports
(Receiving on one port while transmitting another)
BNC
Blinking Red indicates a packet is being transmitted.
Blinking Green indicates a packet is being received.
Alternating Red/Green indicates the 10Base2 port is
Partitioned Out (Disabled).
TP
Steady Green indicates the 10BaseT port is receiving the Link
Integrity Pulse (Keep Alive signal)
Blinking Red indicates a packet is being transmitted.
Blinking Green indicates a packet is being received.
Steady Red indicates the Polarity is reversed on the 10BaseT
port.
Alternating Red/Green indicates the 10BaseT port is
Partitioned Out (Disabled).
2000591-001
DataNET Troubleshooting Guide
Instructions
If an ANG-DN and a DataNET Hub fail to establish a link, this may be
due to one of two situations:
•
a configuration conflict,
•
a link signal quality problem.
Configuration
Conflicts
If after connecting an ANG_DN port the DNETB Green LED never
comes on, or intermittently flashes between green and red, there may be
a configuration conflict. Configuration conflicts can be caused by cabling
or improper software configuration parameters.
Cable Connected to
Wrong Hub or Port
Verify that the Channel A DataNET link is connected to the A Hub half
and that the Channel B DataNET link is connected to the B Hub half.
Verify that both Channels A & B utilize the same port number on their
respective Hub half. Then display the Port Status screen by connecting a
PC to the Configuration Port, logging in, and typing display links. Verify
that the two Ports are connected as expected.
Example
The following example shows that port #1 (ANG_DN Channel A board) is
connected to the ADH Channel. Port#2 (ANG_DN Channel A board) is
also connected to the DataNET Channel A Hub. Note that the Ethernet
cross-link status is Online.
local> display links
Port:
Medium:
Status:
Connected to:
1
ADH Copper Connected
ADH Channel A
2
DN
DN Channel A
Ethernet
Copper Connected
Online
Cable Impedance
Matching
Improper cable impedance matching. Verify that the impedance jumpers
located on J2 are set to match the attached cable impedance. The available selections are for 100, 120, and 150 Ohms.
Cable Shielding
Cable Shielding problems. Make sure the cable is of the recommended
type and that the twisted-pair shield is grounded at one end only. (Hub
end recommended.)
2000591-001
Troubleshooting • 79
DataNET Troubleshooting Guide, Continued
Configuration
Parameter Errors
Verify the configuration parameters by connecting a PC serial port to the
ANG_DN Configuration Port, logging in, and typing config display.
local> config display
Config:
device
ANG_DN
address ip
161.218.54.56
netmask
255.255.255.0
iproute
0.0.0.0
time server ip
0.0.0.0
address ethernet 00.c0.c9.00.d2.3b
device id
More Checks
161.218.54.55
channel
B
loop
1
unit
0
port1
Advance Data Hiway
port2
DataNet Copper
Verify the following:
1. That each ANG_DN board (ANCB) has a unique IP address.
2. That each ANG_DN board (ANCB) uses the same netmask.
3. That the iproute is either not used (0.0.0.0) or points to the address
of your network default router (see your network administrator).
4. That the device id is unique per DataNET device and the same for
both ANCB boards. The Device ID is the DataNET address of the
ANG_DN itself. Therefore both sides must use the same address.
Typically the Device ID is set to the same address as the Channel A
IP address.
5. The channel entry must be unique to each ANG_DN board (ANCB)
and must be either a or b.
6. The DH Loop must be the same on both ANG_DN boards (ANCB)
and the allowable range is Loop # (1-8).
7. The DH Unit must be the same on both ANG_DN boards (ANCB).
The allowable ANG_DN unit range is Unit # (0-31).
80 • Troubleshooting
2000591-001
DataNET Troubleshooting Guiding, Continued
Signal Quality
Problems
If the ANG_DN port LED never goes to green, or intermittently flashes
between green and red, there may be a signal quality problem. Signal
levels should be examined to determine if a particular port has a signal
too large or too small relative to the other ports on the HUB. If a link fails
to connect at all, place the port in a test mode which will cause activity to
occur every ~50 milliseconds instead of every ~5 seconds as on an unconnected link.
Placing Unit in Test Mode
To place the unit in a test mode use the CLI commands to take the link
offline (port stop n) and initiate the test mode (test n). At this time, an
oscilloscope may be taken to the site of the slave device and connected
to monitor the signal. The signal received at the slave should be between
~0.75 v p-p and 5 v p-p. A signal smaller than ~0.75 v p-p is generally
not adequate. The impedance matching jumpers can be changed to correct some signal level issues.
If the condition of excessive signal loss can not be corrected by jumper
settings, it may indicate inadequate cable properties (i.e. too long or
wrong type of cable).
The port can be taken off test mode and put back to normal operation
with the “test off” and “port start n” commands.
2000591-001
Troubleshooting • 81
Obtaining Diagnostics Information
Description
You can access the following Diagnostic information from an Advance
Network Gateway (ANG_DN).
•
•
ADH Channels Status
Error Log
Before You Begin
The following procedure assumes that the Windows Hyper Terminal program residing on your PC has been configured, the ANG_DN is operational, the PC is connected to the ANG_DN and you have logged on.
Ethernet Network
Information
To display current Ethernet network diagnostic information:
1. Log on to the ANG_DN.
2. At the > prompt type: netstat net
The UDP and Interface Statistics screen will appear. The display
shows the number of packets received and transmitted and the
number of errors detected.
82 • Troubleshooting
2000591-001
Obtaining Diagnostic Information, Continued
ADH Channel
Information
To display the current diagnostic information for the ADH channels:
1. Log on to the ANG_DN.
2. At the > prompt type: netstat adh (a or b).
The display shows the number of packets received, transmitted and
the number of errors detected for each of the 31 units on the assigned loop.
Error Log
To display an error log specific to each ANG_DN:
1. Log on to the ANG_DN.
2. At the > prompt type: errorlog
The Most Recent Error log screen appears.
2000591-001
Troubleshooting • 83
Chapter 6
Parts Catalog
Introduction
Overview
This chapter is intended for maintenance personnel.
The Chapter provides a list of replaceable parts and assemblies for the
Advance Network Gateway with DataNET option. Subsequent information includes how to remove and replace the replacement part or assemblies.
How to Place an
Order
Parts can be ordered from:
Siemens Applied Automation
Customer Service Order Entry
500 West Highway 60
Bartlesville, Oklahoma 74003
Inside Oklahoma: 918-662-7370
Outside Oklahoma: 800-448-8224 (toll free)
Internationally: 001-918-662-7370
To ensure an immediate response to your request, you should provide
the following:
2000591-001
•
Purchase order number. If ordering by phone, a confirming P.O.
should be sent.
•
Address where the parts are to be shipped.
•
Address where the invoice is to be sent.
•
Siemens Applied Automation part numbers as listed.
•
Quantity needed of each part.
•
Equipment Serial number or project number of the system (especially for warranty related orders).
•
Preferred method of shipment.
Parts Catalog • 85
Available Parts
Description
86 • Parts Catalog
The available Advance Network Gateway with DataNET spare parts and
applicable part numbers are shown below.
Part Description
Ordering Number
Power Supply, Base Assembly
2015849-802
ANCB Communication Board; Ethernet to Data
Hiway Gateway
2020951-805
Debug Port Extension Cable
2020914-001
Power Supply to Circuit Board Cable
2020276-001
Advance Data Hiway Connector
1221007-014
AC Power Connector
1222010-017
Module to Module Interconnect Cable
1681011-014
Fiber Optics Coupler Assembly
2015828-801
Fiber Optics Coupler Seal Nut
N8005
Fiber Optics Coupler Cable
2020947-001
2000591-001
Appendix
Data Hiway Testing
How to Test the Data Hiway
Post Installation Test
The following test procedure tests the Channel A and Channel B Data
Hiway cable connections. These test procedures insures that the signal
lines are correctly installed.
Referenced testing points are CH A and CH B (+) and negative (-) and
shield ground termination's.
Test Equipment
The following test equipment is required to test continuity of installed
Data Hiway Channel A and Channel B signal lines:
•
•
•
Measuring Signal
Line Continuity
9 Vdc battery, with connector leads and clips
Digital Volt Ohm Meter (DVM) or equivalent
10K ohm resistor, with leads and clips
Data Hiway channel A and channel B + and - signal line continuity can
be checked by performing the following procedures. Devices can be operating on the Data Hiway when making continuity checks. Perform the
check for each device connected to the Data Hiway.
Do not skip testing any devices connected to the Data Hiway. Check at
the incoming termination's on the I/O chassis, the Termination Boards in
the Analyzer Electronics enclosures, LINC units, and any other Data
Hiway devices. Typical problems are reverse polarity; poor contacts on
wiring terminals, opens, and shorts and cross channel wiring. Every point
in the Data Hiway wiring should be carefully checked to ensure correct
wiring.
Step
2000591-001
Procedure
1.
Connect the positive lead of the 9-volt battery through the 10K
ohm resistor to Channel A (+) terminal and connect the negative
lead of the battery to the Channel A (-) terminal at any connection point on the Data Hiway.
2.
Using DVM measure for 9.0 Vdc across Channel A (+) and
Channel A (-).
3.
Repeat steps 1 and 2 for Channel B.
Data Hiway Testing • 87
How to Test the Data Hiway, Continued
Measuring Shield
Continuity
Data Hiway shield lead continuity can be checked by performing the following procedures:
Ground Data Hiway cable shields at only one end of each segment. This
practice reduces ground loop noise.
Step
88 • Data Hiway Testing
Procedure
1.
With Data Hiway communicating with connected Nodes,
temporarily disconnect Channel A shield lead from ground.
2.
Connect 10K ohm resistor to disconnected shield and connect battery positive (+) lead to resistor. Resistor should be
in series with the battery. Connect battery negative (-) lead
to unit ground.
3.
Connect DVM positive (+) lead to channel A and connect
shield and negative (-) to unit ground. Measured voltage
potential should be 9 Vdc.
4.
If 9 Vdc is not measured, the channel A shield line is
grounded at another point; correct problem.
5.
Reconnect channel A and shield lead.
6.
Repeat steps 1 through 5 for Channel B.
7.
Repeat steps 1 through 6 for each shield ground point on
the Data Hiway cable.
2000591-001
Glossary
Definitions
Overview
This section defines important Terms.
Advance Network
Gateway Ethernet
The Advance Network Gateway Ethernet (ANG_EN) is a wall- (or rack-)
mounted unit that is self-contained with power supply and all electronics.
It provides internal field termination points to connect standard Advance
Data Hiway cable “on one side” and Ethernet 10BaseT cabling (Unshielded Twisted Pair) “on the other side”. The Gateway unit requires
120 VAC power wired directly to it.
Ethernet
A data link level protocol comprising the OSI model’s bottom two layers.
It is a broadcast networking technology that can use several different
physical media, including twisted-pair cable and coaxial cable. Ethernet
usually used CSMA/CD. TCP/IP is commonly used with Ethernet networks.
Collisions
The result of two or more LAN stations attempting to use the same
transmission medium at the same time. Collisions are a normal occurrence on Ethernet. A properly functioning Ethernet will experience a relative small percentage of collisions. Typically the collision rate should be
less than 5% of the available bandwidth. Most collisions occur during the
preamble portion of the frame. Most Ethernet controllers automatically
retry, up to 15 times, any packet that has a collision during transmission.
(Except for Late Collisions)
CRC - Cyclic
Redundancy Check
CRC is a method to detect errors. A number is derived from the data that
will be transmitted. By recalculating the CRC at the remote end and
comparing it to the value originally transmitted, the receiving node can
detect errors.
DataNET
The name “DataNET” is used by Siemens Applied Automation to mean
the high-speed communication system inclusive of our application software.
Data Hiway
The term “Data Hiway” refers to the Advance Optichrom Network. The
Advance Network Gateway and DataNET Gateway are used to bridge
the Advance Optichrom network and the Advance DataNET network.
2000591-001
Glossary • 89
Definitions, Continued
Late Collision
A Late Collision is one that occurs after the first 64 bytes in a frame or
packet. Since the smallest Ethernet frame (packet) is 64 bytes in length,
late collisions will not be detected on small packets. Ethernet controllers
do not retransmit packets with late collisions resulting in lost packets.
Late Collisions usually appear as a bad FCS frame. The only time a late
collision can be detected on a 10BaseT network is when the detecting
device is transmitting at the same time.
FCS - Frame Check
Sequence Error
The CRC (Cycle Redundancy Check) remainder transmitted at the end
of a frame. A FCS error is a legal sized Ethernet frame with a bad frame
check sequence.
Ghosts
Ghosts are energy on the cable that appears to be a frame, but does not
have a valid beginning of frame pattern (start delimiter 10101011).
Ground loops and other wiring problems cause some repeaters to believe that a frame is being received. Since the repeater is only reacting to
an AC voltage riding on the cable, there is not a valid frame to pass
along. The repeater, however, transmits this energy along the network.
This may be a jam pattern or a very long preamble. Ghosts events consume bandwidth and can slow down a network. Ghosts are the result of
network elements reacting to noise. The effect of noise on network wiring
is indeterminate. Some network devices will react while others will not.
Ghosts cause random events and can be hard to correct.
Jabber
The term Jabber refers to an Ethernet frame that is greater than the
maximum legal size (Greater than 1518 bytes). Many 10BaseT HUBS
will partition a port that is jabbering.
90 • Glossary
2000591-001
Siemens Applied Automation
500 West Highway 60, Bartlesville, OK 74003
Phone 918-662-7000, Fax 918-662-7052