Sharp CD G14000 Operating instructions

MINI COMPONENT SYSTEM
MODEL
CD-G14000
OPERATION MANUAL
Thank you for purchasing this SHARP product.
To obtain the best performance from this product, please read this
manual carefully. It will guide you in operating your SHARP product.
Accessories
Please confirm that the following accessories are included.
CD-G14000 Mini Component System consisting of CD-G14000
(main unit), CP-G14000 (consisting of 1 set of front speaker) and
1 unit of CP-SW14000 (active subwoofer).
Remote control 1
(RRMCGA159AWSA)
AM loop antenna 1
(QANTL0010AWZZ)
FM antenna 1
(92LFANT1535A)
Red
Black
Wires for front speaker
08/1/15
2
Subwoofer cable
CD-G14000_FRONT.fm
1
TINSZA128AWZZ
CD-G14000
SPECIAL NOTES
NOTE
This
has been tested
to
Class B digital
pursuant to Part
the
the limits for a
These
terference in a residential installation. This equipment generates, uses,
Important Instruction
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols:
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
This product is classified as a CLASS 1 LASER PRODUCT.
Caution - Use of any controls, adjustments or procedures
other than those specified herein may result in hazardous
radiation exposure.
2
Note to CATV system installer:
This reminder is provided to call the CATV system installer's
attention to Article 820-40 of the National Electrical Code that
provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of
cable entry as practical.
accordance with the instructions, may cause harmful interference to radio
However, there is no guarantee that interference
will not occur in a
If this
does cause
harmful
to radio or
can be determined
turning
f
the
to try
.
Connect the equipment into an outlet on a circuit different from that to
Consult the dealer or an experienced radio/TV technician for help.
W
WARNING
to this equipment not expressly approved by the manufacturer could void
NOTE
It is the intent of Sharp that this product be used in full compliance with
the copyright laws of the United States and that prior permission be obtained from copyright owners whenever necessary.
Licensed under one or more of U.S. Pat. 4,972, 484, 5,214,678,
5,323,396, 5,530,655, 5,539,829, 5,544,247, 5,606,618, 5,610,985,
5,740,317, 5,777,992, 5,878,080 or 5,960,037.
FOR YOUR RECORDS
For your assistance in reporting this unit in case of loss or theft,
please record below the model number and serial number which
are located on the rear of the unit.
Please retain this information.
Model number
.......................................................
Serial number
.......................................................
Date of purchase .......................................................
Place of purchase .......................................................
0202
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
IMPORTANT SAFETY INSTRUCTIONS
10) Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from
the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
1) Read these instructions.
2) Keep these instructions.
13) Unplug this apparatus during lightning storms or when unused for
long periods of time.
5) Do not use this apparatus near water.
14) Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
6) Clean only with dry cloth.
Additional Safety Information
3) Heed all warnings.
4) Follow all instructions.
15) Power Sources - This product should be operated only from the
type of power source indicated on the marking label. If you are
not sure of the type of power supply to your home, consult your
product dealer or local power company. For product intended
8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
to operate from battery power, or other sources, refer to the
operating instructions.
9) Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other.
16) Overloading - Do not overload wall outlets, extension cords, or
A grounding type plug has two blades and a third grounding prong.
integral convenience receptacles as this can result in a risk of
The wide blade or the third prong are provided for your safety. If
fire or electric shock.
the provided plug does not fit into your outlet, consult an electrician
for replacement of the obsolete outlet.
17) Object and Liquid Entry - Never push objects of any kind into
this product through openings as they may touch dangerous
voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
7) Do not block any ventilation openings. Install in accordance with
the manufacturer's instructions.
Important Instruction
Electricity is used to perform many useful functions, but it can also
cause personal injuries and property damage if improperly handled.
This product has been engineered and manufactured with the
highest priority on safety. However, improper use can result in
electric shock and/or fire. In order to prevent potential danger, please
observe the following instructions when installing, operating and
cleaning the product. To ensure your safety and prolong the service
life of this product, please read the following precautions carefully
before use.
CD-G14000
3
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
Important Instruction
CD-G14000
IMPORTANT SAFETY INSTRUCTIONS (continued)
18) Damage Requiring Service - Unplug this product from the wall
outlet and refer servicing to qualified service personnel under
the following conditions :
a) When the AC cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,
e) If the product has been dropped or damaged in
any way, and
f) When the product exhibits a distinct change in
performance - this indicates a need for service.
19) Replacement Parts - When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same characteristics
as the original part. Unauthorized substitutions may result in
fire, electric shock, or other hazards.
20) Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
23) Outdoor Antenna Grounding - If an outside antenna or cable system
is connected to the product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges
and built-up static charges. Article810 of the National Electrical Code,
ANSI/NFPA 70, provides information with regards to proper grounding
of the mast and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
Example of antenna grounding as per
National Electrical Code, ANSI/NFPA 70
ANTENNA LEAD IN WIRE
GROUND
CLAMP
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERV ICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELECTRICAL CODE
S2898A
P OWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
24) Protective Attachment Plug - The product is equipped with an attachment
plug having overload protection. This is a safety feature. See Instruction
Manual for replacement or resetting of protective device. If replacement
of the plug is required, be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload
protection as the original plug.
21) Wall or ceiling mounting - When mounting the product on a wall
or ceiling, be sure to install the product according to the method
recommended by the manufacturer.
25) Stand - Do not place the product on an unstable cart, stand, tripod or
table. Placing the product on an unstable base can cause the product to
fall, resulting in serious personal injuries as well as damage to the product.
Use only a cart, stand, tripod, bracket or table recommended by the
22) Power Lines - An outside antenna system should not be located
manufacturer or sold with the product. When mounting the product on a
in the vicinity of overhead power lines or other electric light or
wall, be sure to follow the manufacturer's intructions. Use only the mounting
power circuits, or where it can fall into such power lines or circuits.
hardware recommended by the manufacturer.
When installing an outside antenna system, extreme care should
be taken to keep from touching such power lines or circuits as
contact with them might be fatal.
4
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
Contents
Products that have earned
the ENERGY STAR® are
designed to protect the
environment through
superior energy efficiency.
General Information
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Controls and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 - 10
Preparation for Use
System connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 - 15
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Subwoofer control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Basic Operation
General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setting the clock (Remote Control only) . . . . . . . . . . . . . . . . . 19
CD or MP3/WMA disc Playback
To comply with the ENERGY STAR® standards mentioned above,
please cancel the demonstration mode, as described on page 15.
ENERGY STAR® is a U.S. registered mark.
Special Note
Supply of this product does not convey a license nor imply any right
to distribute content created with this product in revenue-generating
broadcast systems (terrestrial, satellite, cable and/or other
distribution channels), revenue-generating streaming applications
(via Internet, intranets and/or other networks), other revenuegenerating content distribution systems (pay-audio or audio-ondemand applications and the like) or on revenue-generating physical
media (compact discs, digital versatile discs, semiconductor chips,
hard drives, memory cards and the like). An independent license for
such use is required. For details, please visit http://mp3licensing.com
MPEG Layer-3 audio coding technology licensed from Fraunhofer
IIS and Thomson.
Listening to a CD or MP3/WMA disc . . . . . . . . . . . . . . . . .20 - 22
Advanced CD or MP3/WMA disc playback . . . . . . . . . . . .23 - 25
MP3/WMA navigation (only for MP3/WMA files) . . . . . . . .26 - 29
Radio
Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 - 31
Tape Playback
Listening to a cassette tape (TAPE 1 or TAPE 2) . . . . . . .32 - 33
Tape Recording
General Information
ENERGY STAR® Program Information
CD-G14000
Page
Recording on a cassette tape . . . . . . . . . . . . . . . . . . . . . . .33 - 35
Advanced Features
Timer and sleep operation (Remote Control only) . . . . . .36 - 39
Enhancing your system . . . . . . . . . . . . . . . . . . . . . . . . . . .40 - 41
References
Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 - 43
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 - 46
CONSUMER LIMITED WARRANTY . . . . . . . . . . . . . .Back cover
5
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
Precautions
General
Please ensure that the system is positioned in a well-ventilated
area and ensure that there is at least 4" (10 cm) of free space
along the sides, top and back of the equipment.
4" (10 cm)
4" (10 cm)
4" (10 cm)
5
4
3
2
1
REMOTE
SENSOR
TIMER
POWER
ON/ STAND-B Y
c
OPEN/
CLOSE
CD
5
TAPE
(1
2)
4
TUNER
(BAND)
3
PRESET
PRESET
2
AUDIO
IN
1
TUNING
TUNING
VOL.
PLAYBACK (PLAY & STOP)
General Information
PHONES
VOL.
RECORD/ PLAYBACK
AUDIO IN
4" (10 cm)
Do not place active subwoofer system on
the same surface as main unit to prevent
sound interruption during playback.
In case of an electrical storm, unplug the
system for safety.
Hold the AC power plug by the head when
removing it from the AC outlet, as pulling
the cord can damage internal wires.
The AC power plug is used as a disconnect
device and shall always remain readily
operable.
Do not remove the outer cover, as this
may result in electric shock. Refer
internal service to your local SHARP
service facility.
Floor
Use the unit on a firm, level surface free from
vibration.
Keep the unit away from direct sunlight,
strong magnetic fields, excessive dust,
humidity
and
electronic/electrical
equipment
(home
computers,
facsimiles,
etc.)
which
generate
electrical noise.
Do not place anything on top of the unit and subwoofer.
Do not expose the system to moisture, to temperatures higher
than 140˚F (60˚C) or to extremely low temperatures.
If your system does not work properly, disconnect the AC power
cord from the AC outlet. Plug the AC power cord back in, and then
turn on your system.
This unit should only be used within the range of 41˚F - 95˚F
(5˚C - 35˚C).
Warning:
The voltage used must be the same as that specified on this unit.
Using this product with a higher voltage other than that which is
specified is dangerous and may result in a fire or other type of
accident causing damage. SHARP will not be held responsible for
any damage resulting from use of this unit with a voltage other than
that which is specified.
Volume control
The sound level at a given volume setting depends on speaker
efficiency, location and various other factors. It is advisable to avoid
exposure to high volume levels, which occurs while turning the unit
on with the volume control setting up high, or while continually
listening at high volumes. Excessive sound pressure from earphones
and headphones can cause hearing loss.
6
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
Controls and indicators
CD-G14000
5
4
3
2
1
REMOTE
SENSOR
TIMER
POWER
ON/ STAND-BY
c
OPEN/
CLOSE
CD
5
TAPE
(1
2)
4
TUNER
(BAND)
3
PRESET
PRESET
TUNING
TUNING
2
AUDIO
IN
1
VOL.
PLAYBACK (PLAY & STOP)
PHONES
VOL.
Reference page
1. Disc Trays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2. Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3. Power On/Stand-by Button . . . . . . . . . . . . . 18, 20, 30, 32, 36
4. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5. Tape (1
2) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
7. Audio In Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
8. CD or Tape Stop Button . . . . . . . . . . . . . . . . . . . . . . . . 22, 33
9. CD Track Down or Fast Reverse, Tape 2 Rewind,
Tuner Preset Down, Time Down Button . . . . . . . . 22, 31, 33
10. Tape 1 Cassette Compartment . . . . . . . . . . . . . . . . . . . . . . 32
11. Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
12. Audio In Jack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
13. Remote Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
14. Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
15. CD Play or Repeat, Tape Play Button . . . . . . . . . . . . . 20, 23
16. Disc Tray Open/Close Button . . . . . . . . . . . . . . . . . . . . . . . 20
17. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 20
18. CD Track Up or Fast Forward, Tape 2 Fast Forward,
Tuner Preset Up, Time Up Button . . . . . . . . . . . . . 22, 31, 33
19. Tape 2 Cassette Compartment . . . . . . . . . . . . . . . . . . . . . . 32
RECORD/PLAYBACK
General Information
Front panel
AUDIO IN
7
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
Controls and indicators (continued)
Display
General Information
Reference page
1. Disc Number Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2. MP3/WMA Folder Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . 26
3. MP3/WMA Title Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4. MP3 Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5. WMA Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6. Sleep Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
7. Timer Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
8. Timer Recording Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 37
9. Tape 2 Record Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
10. MP3/WMA Total Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
11. Daily Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
12. FM Stereo Mode Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 30
13. FM Stereo Receiving Indicator. . . . . . . . . . . . . . . . . . . . . . . 30
14. Tape Forward Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . 32
15. Memory Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 25, 29, 31
16. Extra Bass Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
17. Disc Repeat Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 24
18. Disc Pause Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
19. Disc Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Rear panel
FMFM
Reference page
1. Cooling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2. Subwoofer Pre-output Jack (Active Subwoofer) . . . . . . . . 14
3. AC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4. FM 75 Ohms Antenna Jack . . . . . . . . . . . . . . . . . . . . . . . . . 12
5. AM Antenna Ground Terminal . . . . . . . . . . . . . . . . . . . . . . 12
6. AM Loop Antenna Terminal . . . . . . . . . . . . . . . . . . . . . . . . . 12
7. Front Speaker Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ANTENNA
ANTENNA
GND
GND AM
AM
OHMS
75 75
OHMS
REAR SPEAKERS
RIGHT
RATED SPEAKER IMPEDANCE : 6 OHMS MIN.
VIDEO
OUT
LEFT
RATED SPEAKER IMPEDANCE : 16 OHMS MIN.
8
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
Front speaker
2
3
1. Woofer
2. Tweeter
3. Bass Reflex Duct
4. Speaker Terminals
4
3
4
5
6
1
2
7
8
Active subwoofer
Reference page
1. Subwoofer
2. Bass Reflex Duct
3. Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4. Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5. Crossover Frequency Control . . . . . . . . . . . . . . . . . . . . . . 17
6. Cooling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7. Subwoofer Input jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8. AC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
General Information
1
9
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
Controls and indicators (continued)
Remote control
1
9
General Information
2
3
4
10
11
12
13
21
18
22
19
23
24
20
25
14
15
5
26 27 28 29
6
7
8
17
16
Reference page
1. Remote Control Transmitter . . . . . . . . . . . . . . . . . . . . . . . . 16
2. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 20
3. Tuning Up, Cursor Up Button . . . . . . . . . . . . . . . . . . . . . . . 26
4. Disc Track Down or Fast Reverse, Tape 2 Rewind,
Tuner Preset Down, Time Down, Cursor Left Button
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 22, 26, 31, 32, 36
5. Clock/Timer Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6. Character Input/Disc Direct Search Buttons . . . . . . . . 23, 28
7. Equalizer Mode Select Button . . . . . . . . . . . . . . . . . . . . . . . 18
8. Extra Bass Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 18
9. On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
10. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
11. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
12. Tape (1
2) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
13. Audio In Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
14. Disc Track Up or Fast Forward, Tape 2 Fast Forward,
Tuner Preset Up, Time Up, Cursor Right Button
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 22, 26, 31, 32, 36
15. Tuning Down, Cursor Down Button . . . . . . . . . . . . . . . . . . 26
16. Volume Up and Down Buttons . . . . . . . . . . . . . . . . . . . . . . 18
17. Clear/Dimmer Button . . . . . . . . . . . . . . . . . . . . . . . . . . . 18, 25
18. Disc Random Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
19. Disc Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
20. Tape Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
21. Memory Button . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 25, 31, 36
22. Disc Pause Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
23. Disc Play or Repeat Button . . . . . . . . . . . . . . . . . . . . . . . . . 24
24. Tape Play Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32, 33
25. Tape 2 Record Pause Button . . . . . . . . . . . . . . . . . . . . . . . 34
26. MP3/WMA Navigation Mode Select Button . . . . . . . . . . . . 26
27. Character Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
28. MP3/WMA Display Button . . . . . . . . . . . . . . . . . . . . . . . . . . 22
29. Enter Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
10
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
System connections
CD-G14000
Make sure to unplug the AC power cord before making any connections.
Front
speaker
(right)
FM
antenna
AM loop
antenna
Front
speaker
(left)
Active subwoofer
Subwoofer
connection
(see page 14)
FM
ANTENNA
GND AM
RATED SPEAKER IMPEDANCE : 6 OHMS MIN.
75 OHMS
Preparation for Use
Antenna connection (see page 12)
Speaker connection
(see page 12)
To AC outlet
To AC outlet (AC 120 V ~ 60 Hz)
AC power connection (see page 14)
11
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
System connections (continued)
Antenna connection
Speaker connection
Supplied FM antenna:
Connect the FM antenna wire to the
FM
FM 75 OHMS jack and position the FM
antenna wire in the direction where the antenna
strongest signal can be received.
Front speakers:
Connect the black wire to the FRONT SPEAKERS (–) terminal, and
the red wire to the FRONT SPEAKERS (+) terminal.
Supplied AM loop antenna:
Connect the AM loop antenna to the
AM and GND terminals. Position the
AM loop antenna for optimum
reception. Place the AM loop antenna
on a shelf, etc., or attach it to a stand
or a wall with screws (not supplied).
AM loop
antenna
Front speaker (right)
ANTENNA
FM
GND
Front speaker (left)
RATED SPEAKER IMPEDANCE : 6 OHMS MIN.
Preparation for Use
CD-G14000
AM
75 OHMS
Note:
Placing the antenna on the unit or near the AC power cord may
cause noise pickup. Place the antenna away from the unit for better
reception.
Installing the AM loop antenna:
< Assembling >
< Attaching to the wall >
Wall
Screws (not supplied)
Front speaker (right)
Front speaker (left)
Red
Black
Caution:
Connect the speaker wires to the speakers first, then to the unit.
If you use other speakers with impedance lower
than that specified, the unit may be damaged.
Front speakers: 6 ohms
Do not mistake the right and the left channels. The
right speaker is the one on the right side when you
face the unit.
Incorrect
Do not let the bare speaker wires touch each other.
Do not allow any objects to fall into or to be placed
in the bass reflex ducts.
Do not stand or sit on the speakers. You may be
injured.
Incorrect
12
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
Placing the speaker system
Outdoor FM antenna
To enjoy the surround effect, we recommend that you place each
speaker as shown to the below.
Use an outdoor FM antenna if you require better reception.
Consult your dealer.
Active
subwoofer
Front
speaker
(left)
ANTENNA
FM
Front
speaker
(right)
Main unit
GND
AM
Outdoor
FM antenna
75 OHMS
75 ohms
coaxial cable
Note:
When an outdoor FM antenna is used, disconnect the supplied FM
antenna wire.
Notes:
Front speakers are not magnetically shielded and must not be
placed near the TV.
The active subwoofer is magnetically shielded and does not affect
the display even if it is placed near the TV.
However, some color variation may occur, depending on the type
of TV used.
Preparation for Use
TV
If color variation occurs:
Turn off the TV (from the power switch).
After 15 - 30 minutes, turn the TV on again.
If the color variation is still present:
Move the speakers further away from the TV.
If any kind of magnet or an electromagnet is placed too close to
the TV and the system, irregular colors may appear on the TV
screen.
Note:
The speaker grilles are not removable.
13
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
System connections (continued)
Make sure to unplug the AC power cord of the main unit before
making any connections.
Connecting the subwoofer
Use the subwoofer cable to connect the SUBWOOFER PRE-OUT
jack on the main unit and the SUBWOOFER IN jack on the active
subwoofer.
AC power connection
After checking all the connections have been made correctly, plug
the AC power cord of this unit into the AC outlet. If you plug in the unit
first, the unit will enter the demonstration mode.
Main unit
FM
ANTENNA
GND AM
75 OHMS
RATED SPEAKER IMPEDANCE : 6 OHMS MIN.
FM
ANTENNA
GND AM
75 OHMS
AC outlet
(AC 120 V ~ 60 Hz)
RATED SPEAKER IMPEDANCE : 6 OHMS MIN.
Preparation for Use
Main unit
To subwoofer
output jack
Active subwoofer
Subwoofer cable
Active subwoofer
To subwoofer
input jack
AC outlet
(AC 120 V ~ 60 Hz)
14
Notes:
The unit will start the tape initialization when plugged in to the AC
outlet. During this process, an initializing sound will be heard and
the unit cannot be turned on. Wait until the process is finished.
Unplug the AC power cord from the AC outlet if the unit will not be
in use for a prolonged period of time.
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
Cooling fan:
The main unit and the active subwoofer are built with a cooling fan at
the rear of the units for improved cooling. Please do not cover the
opening of the fan with any obstacles, as this will block proper
ventilation.
Demonstration mode
When you plug the unit in for the first time, the unit will enter the
demonstration mode. You will see words scroll.
FM
To cancel the demonstration mode:
When the unit is in the power stand-by mode (demonstration mode),
press the X-BASS/DEMO button. The unit will enter the low power
consumption mode.
ANTENNA
GND AM
RATED SPEAKER IMPEDANCE : 6 OHMS MIN.
75 OHMS
Active subwoofer
Preparation for Use
Main unit
To return to the demonstration mode:
When the unit is in the power stand-by mode, press the
X-BASS/DEMO button again.
Note:
When the power is on, the X-BASS/DEMO button can be used to
select the extra bass mode.
15
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
Remote control
Battery installation
Use 2 “AA” size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.
1
2
Preparation for Use
3
Open the battery cover.
Insert the batteries according to the direction indicated in
the battery compartment.
When inserting or removing the batteries, push them toward the
battery terminals.
Close the cover.
Notes concerning use:
Replace the batteries if the operating distance is reduced or if the
operation becomes erratic.
Periodically clean the transmitter on the remote control and the
sensor on the unit with a soft cloth.
Exposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit.
Keep the remote control away from moisture, heat, shock, and
vibrations.
Test of the remote control
Check the remote control after checking all the connections (see
pages 11 - 15).
Point the remote control directly at the remote sensor on the unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you
can enjoy music.
Precautions for battery use:
Replace all old batteries with new ones at the same time.
Do not mix old and new batteries.
Remove the batteries if the unit will not be used for long periods
of time. This will prevent potential damage due to battery leakage.
Remote sensor
5
4
3
2
1
REMOTE
SENSOR
TIMER
POWER
ON/ STAND-BY
c
OPEN/
CLOSE
CD
5
TAPE
(1
2)
4
Caution:
Do not use rechargeable batteries (nickel-cadmium battery, etc.).
Installing the batteries incorrectly may cause the unit to
malfunction.
Batteries (battery pack or batteries installed) shall not be exposed
to excessive heat such as sunshine, fire or the like.
TUNER
(BAND)
3
PRESET
PRESET
2
AUDIO
IN
1
TUNING
TUNING
VOL.
PLAYBACK (PLAY & STOP)
PHONES
VOL.
RECORD/PLAYBACK
AUDIO IN
Battery removal:
Open the battery cover and pull up the battery to take out.
16
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
Subwoofer control
CD-G14000
Before you turn the system on/off on the main unit, minimize the
speaker volume on the main unit and turn the VOLUME control of
the subwoofer to “–”.
Subwoofer light up
The subwoofer unit surface will light up and blink according to BASS
SOUND LEVEL.
During STAND-BY MODE (low power consumption mode):
When subwoofer is turned ON, no light will be emitted from the
subwoofer unit.
Notes:
Observe the following to avoid malfunction and sound distortion.
Do not set the volume too high on the main unit. The subwoofer
may be damaged.
Before you switch on/off on the main unit, minimize the volume on
the main unit.
Unplug the AC power cord when connecting the subwoofer cable.
Power switch
Preparation for Use
During STAND-BY MODE (demo mode):
When subwoofer is turned ON, the subwoofer unit will emit blinking
light.
Press the POWER ON/OFF button to turn ON the Active subwoofer.
Volume control
Turn the VOLUME control clockwise to increase the volume, and turn
it counterclockwise to decrease the volume.
Crossover frequency control
Adjust the high frequency cut-off point. Frequencies higher than the
set frequency are removed.
To emphasize the bass, turn this control toward 35 Hz and increase
the volume.
17
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
General control
Volume control
Main unit operation:
When the VOLUME control is turned
clockwise, the volume will increase. When
it is turned counterclockwise, the volume
will decrease.
Remote control operation:
Press the VOLUME (+ or –) button to
increase or decrease the volume.
5
4
3
2
1
POWER
ON/ STAND-BY
REMOTE
SENSOR
TIMER
POWER
ON/ STAND-BY
c
OPEN/
CLOSE
CD
5
TAPE
(1
2)
4
TUNER
(BAND)
3
PRESET
PRESET
2
AUDIO
IN
1
TUNING
TUNING
VOL.
0 ..... 30 MAXIMUM
VOL.
— VOL.
VOL.
Bass control (X-BASS)
Basic Operation
When the power is first turned on, the unit
will enter the extra bass mode which
emphasizes the bass frequencies, and “XBASS” will appear. To cancel the extra
bass mode, press the X-BASS/DEMO
button.
Equalizer
When the EQUALIZER MODE button is pressed, the current mode
setting will be displayed. To change to a different mode, press the
EQUALIZER MODE button repeatedly until the desired sound mode
appears.
To turn the power on
Press the ON/STAND-BY button to turn the power on.
After use:
Press the ON/STAND-BY button to enter the power stand-by mode.
No equalization.
ROCK
For rock music.
CLASSIC For classical music.
Display brightness control
POPS
To dim the display brightness, hold down the CLEAR/DIMMER
button on the remote control for 2 seconds or more.
For pop music.
VOCAL Vocals are
enchanced.
JAZZ
Volume auto fade-in
If you turn off and on the main unit with the volume set to 27 or
higher, the volume starts at 16 and fades in to the last set level.
FLAT
For jazz.
Note:
The extra bass mode is canceled when the EQUALIZER MODE
button is pressed.
18
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
Setting the clock (Remote Control only)
5
CD-G14000
Press the
or
button to adjust the hour and then
press the MEMORY button.
or
button once to advance the time by
Press the
1 hour. Hold it down to advance continuously.
Press the
or
button to adjust the minutes and
then press the MEMORY button.
In this example, the clock is set for the 12-hour (AM 12:00) display.
1
2
3
Press the ON/STAND-BY button to turn the power on.
4
Press the
or
button to select 12-hour or 24-hour
display and then press the MEMORY button.
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to
select “CLOCK”, and press the MEMORY button.
“AM 12:00”
“AM 0:00”
“0:00”
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
The 24-hour display will appear.
(0:00 - 23:59)
or
button once to advance the time by
Press the
1 minute. Hold it down to change the time in 5-minute intervals.
To confirm the time display:
[When the unit is in the stand-by mode]
Press the CLOCK/TIMER button.
The time display will appear for about 10 seconds.
[When the power is on]
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to display the
time. The time display will appear for about 10 seconds.
Note:
The “CLOCK” will appear or time will flash to confirm the time
display when the AC power supply is restored after a power failure
or unplugging the unit. If incorrect, readjust the clock as follows.
To readjust the clock:
Perform “Setting the clock” from step 1. If the “CLOCK” does not
appear in step 3, step 4 (for selecting the 12-hour or 24-hour
display) will be skipped.
To change the 12-hour or 24-hour display:
1 Clear all the programmed contents. [Refer to “Clearing all the
memory (reset)” on page 43 for details.]
2 Perform “Setting the clock” from step 1.
Basic Operation
6
19
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
Listening to a CD or MP3/WMA disc
This system can play back a standard CD, CD-R/RW in the CD format
and CD-R/RW with MP3 or WMA files, but cannot record on them.
Some audio CD-R and CD-RW discs may not be playable due to the
state of the disc or the device that was used for recording.
POWER
ON/ STAND-BY
5
4
3
2
CD or MP3/WMA disc Playback
1
MP3:
MP3 is a form of compression. It is an acronym which stands
for MPEG Audio Layer 3.
MP3 is a type of audio code which is processed by significant
compression from the original audio source with very little loss
in sound quality.
This system supports MPEG 1 Layer 3, MPEG 2 Layer 3, and
VBR files.
During VBR file playback, time counter in the display may differ
from its actual playback time.
Bitrate which is supported by MP3 is 32 ~ 320 kbps.
c
REMOTE
SENSOR
TIMER
OPEN/
CLOSE
POWER
ON/ STAND-BY
c
OPEN/
CLOSE
CD
5
CD
TAPE
TAPE
(1 (1 2) 2)
4
TUNER
(BAND)
5
3
PRESET
PRESET
TUNING
TUNING
2
AUDIO
IN
1
VOL.
VOL.
4
3
PLAYBACK (PLAY & STOP)
RECORD/PLAYBACK
2
PHONES
AUDIO IN
1
WMA:
WMA files are Advanced System Format files that include
audio files which are compressed with Windows Media Audio
codec. WMA is developed by Microsoft as an audio format file
for Windows Media Player.
“MP3” or “WMA” indicator will light up after the unit reads
information on an MP3 or WMA disc.
Bitrate which is supported by WMA is 64 ~ 160 kbps.
Auto power on function:
When you press any of the following buttons, the unit turns on.
CD button (main unit and remote control): The unit turns on and
the “CD” function is activated.
CD / button on the remote control: The unit turns on and CD
playback starts (regardless of the last function).
/ button on the main unit: The unit turns on and playback of
the last function starts (CD, TAPE, TUNER, AUDIO IN).
Auto power off function:
In the stop mode of CD, MP3 or WMA operation, the main unit enters
the stand-by mode after 15 minutes of inactivity.
20
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
1
Press the POWER ON/STAND-BY button to turn the power
on.
2
3
Press the CD button.
4
Place the disc on the disc tray 1, label side up.
Be sure to place 3" (8 cm) disc in the middle of the disc trays.
Press the
1 button and within 5 seconds, press the
OPEN/CLOSE button to open the disc tray 1.
5" (12 cm)
5
3" (8 cm)
Press the OPEN/CLOSE button to close the disc tray 1.
MP3 indicator
WMA indicator
[CD]
[MP3/WMA]
Total number of
tracks on the disc
Total playing
time of the disc
Total number Total number
of folders
of files
Due to the structure of the disc information, it takes longer to
read an MP3/WMA disc than a normal CD (approximately 20
to 90 seconds).
6
You can place discs on the trays 2 - 5 by following steps
3 - 5.
7
Press the
/
Playback will begin from track 1 on disc 1. After that disc finishes
playing, the next disc will automatically play.
After the last track on the fifth disc is played, the unit will stop
automatically.
When there is no disc in one of the disc trays (1 - 5), the empty
tray will be skipped to the next tray with a disc.
To exchange other discs while playing a disc:
Press one of the 1 - 5 buttons for the stopped disc and within 5
seconds, press the button and exchange discs.
To remove the discs:
In the stop mode, press the
press the button.
1-
5 buttons and within 5 seconds,
Caution:
Do not place two discs in one disc tray.
Do not play discs of special shapes (heart, octagon, etc.) as it
may cause malfunctions.
Do not push the disc tray while it is moving.
If the power fails while the tray is open, wait until the power is
restored.
If the disc tray is stopped with force,“ER-CD20” will appear on the
display for 3 seconds and the unit will not function. If this occurs,
press the ON/STAND-BY button to enter the power stand-by
mode and then turn the power on again.
If TV or radio interference occurs during CD operation, move the
unit away from the TV or radio.
If a disc is damaged, dirty, or loaded upside down, the disc will
skip or not play.
CD or MP3/WMA disc Playback
Playback
button to start playback.
Disc play indicator
21
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
Listening to a CD or MP3/WMA disc (continued)
Various disc functions
CD or MP3/WMA disc Playback
Function
Main unit
Remote
control
Operation
Play
Press in
mode.
Stop
Press in the playback
mode.
Pause
Press in the playback
mode. Press the /
button
to
resume
playback from the
paused point.
Press in the playback
or stop mode.
If you press the button
in the stop mode,
press the / button
to start the desired
track.
Track up/
Track down
PRESET
PRESET
Fast
forward/
Fast
reverse
the
stop
Notes for CD:
Track up/track down is possible only within individual discs.
Fast forward/fast reverse is possible only within individual discs.
When the end of the last track is reached during fast forward,
“END” will appear on the display and CD operation will be paused.
When the beginning of the first track is reached during fast
reverse, the unit will enter the playback mode.
Notes for MP3/WMA discs:
Track up/track down is possible only within individual discs.
The sound is heard during fast forward/fast reverse with a CD, but
not with an MP3/WMA disc. For fast forward or fast reverse of an
MP3/WMA disc, refer to playback time on the display.
Fast forward/fast reverse is possible only within individual tracks.
When the end of the track is reached during fast forward, the next
track will be played. Playback of the track will begin when its
beginning is reached during fast reverse.
To change the display (MP3/WMA discs only)
While a disc is playing, press the DISPLAY
button.
Each time the button is pressed, the display
will change as follows.
Press and hold down
in the playback mode.
Release the button to
resume playback.
PRESET
PRESET
Track number Elapsed
playback time
Folder name
File name
22
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
Advanced CD or MP3/WMA disc playback
To specify a disc to play
Direct track search
You can play a disc by specifying the disc number.
By using the direct search buttons, the desired tracks on the current
disc can be played.
1
Press one of the
1-
5 buttons to select the desired disc.
Use the direct search buttons on
the remote control to select the
desired track while playing the
selected disc.
Selected track number
Selected disc number
2
Within 5 seconds, press the
/
button on the main unit.
The direct search buttons allow you to select up to number 9.
When selecting number 10 or more, use the “+10” button.
A. For example, to choose 13
1 Press the “+10” button once.
2 Press the “3” button.
5
4
3
2
1
REMOTE
SENSOR
TIMER
POWER
ON/ STAND-BY
c
OPEN/
CLOSE
CD
5
TAPE
(1 (12)
TAPE
2)
4
TUNER
(BAND)
3
PRESET
PRESET
2
Playback will begin from track 1 on the chosen disc.
After the last track on the last disc is played, the unit stops
automatically.
Note:
If the disc tray with no disc is selected, playback will not start and the
disc indicator will disappear.
To stop playback:
Press the (CD ) button.
B. For example, to choose 30
1 Press the “+10” button three times.
2 Press the “0” button.
CD or MP3/WMA disc Playback
CD-G14000
If the direct search buttons are pressed while the disc is stopped,
press the / button to start the desired track on the current disc.
Notes:
A track number higher than the number of tracks on the disc
cannot be selected.
During random play, direct search is not possible.
23
08/1/16
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
Advanced CD or MP3/WMA disc playback (continued)
Repeat play
Random play
Repeat play can play all 5 discs, all tracks on a chosen disc, or a
programmed sequence continuously.
The tracks on the disc(s) can be played in random order automatically.
CD or MP3/WMA disc Playback
To repeat one disc:
Press the / button twice.
To random play all tracks on up to 5 discs:
Press the RANDOM button on the remote control.
To repeat all tracks on up to 5 discs:
Press the / button three times.
To repeat desired tracks:
Perform steps 1 - 6 in “Programmed play” section on page 25 and
then press the / button twice.
To cancel repeat play:
Press the / button again.
“ ” will disappear.
To cancel random play:
Press the / button.
“R” will disappear.
Notes:
If you press the
button during random play, you can move to
the next track by the random operation. On the other hand, the
button does not allow you to move to the previous track. The
beginning of the track being played will be located.
In random play, the unit will select and play tracks automatically.
(You cannot select the order of the tracks.)
Caution:
After performing repeat or random play, be sure to press the
(CD ) button. Otherwise, the disc(s) will play continuously.
24
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
You can choose up to 32 selections for playback in the order you like.
1
2
While in the stop mode, press the
MEMORY button to enter the
programming save mode.
To cancel the programmed play mode:
While in the stop mode and the “MEMORY” indicator is lit, press the
CLEAR/DIMMER button on the remote control. The “MEMORY”
indicator will disappear and all the programmed contents will be
cleared.
Press one of the 1 - 5 buttons
to select the desired disc.
Selected disc number
3
Press the direct search buttons
on the remote control to select
the desired track.
Selected track number
You can also select a track by pressing the
or
button.
4
Press the MEMORY button to save
the track number.
5
Repeat steps 2 - 4 for other tracks. Up to 32 tracks can be
programmed.
If you make a mistake, the programmed tracks can be cleared
by pressing the CLEAR/DIMMER button.
6
Press the (CD ) button.
The total number in memory will
appear.
7
Press the
/
To clear the programmed selections:
Press the CLEAR/DIMMER button on the
remote control while the “MEMORY” indicator
is flashing.
Each time the button is pressed, one track will
be cleared, beginning with the last track
programmed.
Adding tracks to the program:
If a program has been previously stored, the “MEMORY” indicator
will be displayed. Then follow steps 1 - 6 to add tracks. The new
tracks will be stored after the last track of the original program.
To check which tracks are programmed:
While the unit is stopped in the programmed play mode, press the
or
button.
Notes:
When a disc with programmed tracks is ejected, the program is
automatically canceled.
Even if you press the ON/STAND-BY button to enter the stand-by
mode or change the function from CD to another, the programmed
selections will not be cleared.
During the program operation, random play is not possible.
CD or MP3/WMA disc Playback
Programmed play
button to start playback.
25
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD or MP3/WMA disc Playback
CD-G14000
MP3/WMA navigation (only for MP3/WMA files)
MP3/WMA navigation:
You can search and play files by folder or title. For example, when
you assign three titles to a file, enter genre (such as jazz) as title 1,
album name as title 2, and music title as title 3 to search the file by
any title.
You can search and play files by folder or title 1/2/3 within one
MP3/WMA disc (see page 27).
By entering a name, you can search files by folder or title 1/2/3
within one MP3/WMA disc (see page 28).
Folders or titles can be programmed within one MP3/WMA disc
(see page 29).
When you enter file names on your PC, connect words with hyphens.
This product recognizes the first word as title 1, second one as title
2, and third one as title 3. Up to three words can be recognized.
Example:
Folder
Title 1
Title 2
Title 3
(File name)
Folder
Title 1
Title 2
Title 3
AAA
(POPULAR-HITS 1-A MUSIC.mp3)
(POPULAR-HITS 2-B MUSIC.mp3)
BBB
(JAZZ-HITS 1-A MUSIC.mp3)
(JAZZ-HITS 2-B MUSIC.mp3)
CCC
(ROCK-HITS 1-A MUSIC.mp3)
(ROCK-HITS 2-B MUSIC.mp3)
(ROCK-HITS 3-C MUSIC.mp3)
(ROCK-HITS 4-D MUSIC.mp3)
Notes:
MP3 files must have the extension “.mp3”.
WMA files must have the extension “.wma”.
Up to 100 folders or 300 files can be read on the unit. If either limit
is exceeded, no more folders/files are displayed.
This unit recognizes and displays up to 48 characters for folder
names, and up to 32 characters for title 1/2/3.
All file/folder names appear in uppercase.
26
08/1/16
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
File search (by folder or title 1/2/3)
You can search and play files by folder or title 1/2/3 within one MP3/
WMA disc.
1
Press one of the
1 5 buttons to select a disc tray
containing an MP3/WMA disc.
2
Press the
disc.
3
Press the CD button to stop playback.
“NAVI READ” appears and the display shows the total number
of folders and files on the selected disc.
Use the
or
cursor button to scroll and select a folder
(or title), and then press the ENTER button.
Folder name
button, and the unit starts to read the MP3
If you press the / button instead of the ENTER button, all
files in the selected folder (or title) are played.
8
Use the
4
5
9
Press the NAVIGATION button.
Press the , ,
or
cursor
button on the remote control to
select “FOL”, “T-1”, “T-2” or “T-3”.
To search files by folder name,
select “FOL” (will flash).
Folder
Title 1
MP3
Title 2
Title 3
The following steps describe file search by folder:
6
Press the ENTER button.
The total number of folders (or titles) appears for 2 seconds,
and names of the first 2 folders (or titles) are displayed.
Folder name
The NAVIGATION button allows you to go one step back.
Press the DISPLAY button to
check the number of files.
cursor button to scroll and select a file.
File name
MP3 indicator
WMA indicator
Total number Total number
of folders
of files
or
Press the / button to start playback.
The unit plays from the selected file to the last file in the
selected folder (or title), and the previous display returns.
File search by title 1/2/3:
In step 5, select “T-1”, “T-2” or “T-3” and follow the same steps as
file search by folder.
The unit searches all files on the disc, regardless of the folder.
To stop playback:
Press the CD button.
To exit the MP3/WMA navigation mode:
In the stop mode, press the CD button.
CD or MP3/WMA disc Playback
/
7
Notes:
In the MP3/WMA navigation mode, direct play and direct search
functions are disabled.
If a folder, title or file name does not appear, or appears
incorrectly, remove and reinsert the disc and try again.
If you press the RANDOM button in the stop mode, the MP3/WMA
navigation mode will be canceled.
27
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
MP3/WMA navigation (only for MP3/WMA files) (continued)
Character search (for folder or title 1/2/3)
CD or MP3/WMA disc Playback
By entering a name, you can search files by folder or title 1/2/3 within
one MP3/WMA disc.
1
Perform steps 1 - 3 in “File search (by folder or title 1/2/3)”
on page 27.
2
3
Press the NAVIGATION button.
4
5
6
Press the , ,
or
cursor
button on the remote control to
select “FOL”, “T-1”, “T-2” or
“T-3”. To search files by folder
name, select “FOL” (will flash).
or
or
When finished, press the ENTER button. The unit searches
for the same name within folders (or titles).
If the search word is not in the folder (or title) name, “NOT
FOUND” appears and the menu returns.
Folder
Title 1
Title 2
Title 3
Press the CHARACTER button for 2 seconds.
The display will be ready for editing characters.
1st row: String table
2nd row: Input editor (8 digits)
Press the
alphabet.
Press the
display.
8
cursor button to select the desired
button to go to the next page of character
Press the CHARACTER button and the active character will
be entered in the 2nd row of the display.
9
Use the or
(or title).
10
Press the / button to start playback.
All files in the selected folder (or title) are played, and the
previous display returns.
cursor button to scroll and select a folder
To exit the MP3/WMA navigation mode:
In the stop mode, press the CD button.
Notes:
The unit searches regardless of the case, and names found will
appear in uppercase.
Some symbols do not appear properly.
Character entry with direct buttons:
The direct buttons on the remote
control can also be used for
character entry.
In step 5 on the left, use buttons 0 9 to enter alphabets.
Alphabet types change as you
press a button.
For example, press “2” four times to enter “C”.
To delete an entered character, move the cursor to the
character with the
or
button and press the CLEAR/
DIMMER button on the remote control.
7
Repeat steps 5 and 6 to enter characters.
In the folder (or title) name search, you do not have to enter the
full name. The unit searches for names beginning with the
entered characters.
2
A
B
C
Characters:
1
2 ABC
3 DEF
4 GHI
5 JKL 6 MNO 7 PQRS 8 TUV 9 WXYZ
0
: indicates a space.
28
08/1/16
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
Folders or titles can be programmed within one MP3/WMA disc.
Folder, title 1, title 2 and title 3 cannot be programmed together
simultaneously.
1
2
3
4
Perform steps 1 - 3 in “File search (by folder or title 1/2/3)”
on page 27.
Press the , , or cursor button on the remote control
to select “FOL”, “T-1”, “T-2” or “T-3” and then press the
ENTER button.
The total number of folders (or titles) appears for 2 seconds,
and names of the first 2 folders (or titles) are displayed.
Press the or cursor button to select the desired folder
(or title) and then press the MEMORY button.
Repeat step 4 for other folders (or titles).
Up to 10 folders (or 10 titles) can be programmed.
6
Flashes if the folder (or title)
is programmed
Press the NAVIGATION button.
The folder (or title) is memorized with all the files.
5
To check, add or delete programmed contents:
In the stop mode, select a folder (or title) with the
or
cursor
button. If the folder (or title) is programmed, “MEMORY” flashes.
Press the
/
button to start playback.
Programmed play will always start from the smallest folder (or
title) number.
When you press the MEMORY button with “MEMORY” flashing,
the folder (or title) is removed from the program.
If you press the MEMORY button with “MEMORY” off, the folder
(or title) is added to the program.
To clear all programs, press the CLEAR/DIMMER button in the
stop mode.
To exit the MP3/WMA navigation mode:
In the stop mode, press the CD button.
The programmed contents are cleared.
Notes:
The programmed contents are cleared when you eject a disc,
play another disc, switch the function, or enter the stand-by mode
with the ON/STAND-BY button.
If you press the RANDOM button in the stop mode, the MP3/
WMA navigation mode will be canceled.
If tracks are programmed using track numbers (see
“Programmed play” on page 25):
In the MP3/WMA navigation mode, only program by folder (or title)
name are played. When you exit the mode, the program by folder (or
title) name are cleared.
When you exit the MP3/WMA navigation mode, program by track
number are canceled.
(Program by track number are cleared when you remove the disc.)
CD or MP3/WMA disc Playback
Programmed play (for folder, title 1/2/3)
To stop playback:
Press the CD button.
The programmed contents are not cleared.
29
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
Listening to the radio
Tuning
5
4
3
2
1
POWER
ON/ STAND-BY
1
2
Press the ON/STAND-BY button to turn the power on.
3
Press the TUNING (
station.
REMOTE
SENSOR
TIMER
POWER
ON/ STAND-BY
c
OPEN/
CLOSE
CD
5
Press the TUNER (BAND) button repeatedly to select the
desired frequency band (FM or AM).
or
) button to tune in to the desired
TAPE
(1
2)
4
TUNER
(BAND)
3
PRESET
PRESET
2
AUDIO
IN
1
TUNING
TUNING
VOL.
VOL.
TUNER
(BAND)
PLAYBACK (PLAY & STOP)
RECORD/PLAYBACK
AUDIO IN
Radio
PHONES
Manual tuning:
Press the TUNING ( or ) button as many times as required
to tune in to the desired station.
Auto tuning:
When the TUNING ( or ) button is pressed for more than 0.5
seconds, scanning will start automatically and the tuner will
stop at the first receivable broadcast station.
Notes:
When radio interference occurs, auto scan tuning may stop
automatically at that point.
Auto scan tuning will skip weak signal stations.
To stop the auto tuning, press the TUNING ( or ) button
again.
Auto power on function:
When you press any of the following buttons, the unit turns on.
TUNER (BAND) button (main unit and remote control): The unit
turns on and the “TUNER” function is activated.
/ button on the main unit: The unit turns on and playback of
the last function starts (CD, TAPE, TUNER, AUDIO IN).
To receive an FM stereo transmission:
Press the TUNER (BAND) button to display the “ST” indicator.
“ ” will appear when an FM broadcast is in stereo.
If the FM reception is weak, press the TUNER (BAND) button to
extinguish the “ST” indicator. The reception changes to monaural,
and the sound becomes clearer.
FM stereo mode indicator
FM stereo receiving indicator
30
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
Memorizing a station
To recall a memorized station
You can store 40 AM and FM stations in memory and recall them at
the push of a button. (Preset tuning)
Press the PRESET ( or
select the desired station.
Perform steps 1 - 3 in “Tuning” on page 30.
To scan the preset stations
Press the MEMORY button to enter the preset tuning
saving mode.
The stations saved in memory can be scanned automatically.
(Preset memory scan)
1
2
3
4
Within 30 seconds, press the PRESET ( or ) button to
select the preset channel number.
Store the stations in memory, in order, starting with preset
channel 1.
Press the PRESET ( or ) button for more than 0.5 seconds.
The preset number will flash and the programmed stations will be
tuned in sequentially, for 5 seconds each.
Press the PRESET ( or ) button again when the desired
station is located.
5
4
3
2
1
Radio
1
2
) button for less than 0.5 seconds to
REMOTE
SENSOR
TIMER
POWER
ON/ STAND-BY
Within 30 seconds, press the MEMORY button to store that
station in memory.
c
OPEN/
CLOSE
CD
5
TAPE
(1
2)
4
TUNER
(BAND)
3
PRESET
PRESET
2
AUDIO
IN
PRESET
1
PRESET
TUNING
TUNING
VOL.
VOL.
If the “MEMORY” and preset number indicators disappear
before the station is memorized, repeat the operation from step
2.
5
Repeat steps 1 - 4 to set other stations, or to change a
preset station.
When a new station is stored in memory, the station previously
memorized for that preset channel number will be erased.
Note:
The backup function protects the memorized stations for a few hours
should there be a power failure or the AC power cord become
disconnected.
To erase entire preset memory
1
2
Press the ON/STAND-BY button to enter the power stand-by
mode.
While pressing down the button and the
button, press
the TUNER(BAND) button until “TUNER CL” appears.
TUNER
(BAND)
PRESET
08/1/15
CD-G14000_EN.fm
31
TINSEA128AWZZ
CD-G14000
Listening to a cassette tape (TAPE 1 or TAPE 2)
Before playback:
For playback, use normal or low-noise tapes for the
best sound. (Metal or CrO tapes are not
recommended.)
Do not use C-120 tapes or poor-quality tapes, as
they may cause malfunctions.
Before loading a tape into the cassette compartment,
tighten the slack with a pen or a pencil.
Tape playback
1
2
Open
the
cassette
compartment by pushing
the area marked “ ”.
5
5
CD
CD
4
4
TAPE 1/2
3
PRESET
3
2
PRESET
TUNER(BAND)
PRESET
2
PRESET
1
1
AUDIO IN
TUNING
TUNING
VOL.
TUNING
VOL.
TUNING
— VOL.
— VOL.
PUSH EJECT
PUSH EJECT
RECORD/PLAYBACK
RECORD/PLAYBACK
& STOP)
PLAYBACK (PLAY
PHONES
3
Tape Playback
Press the ON/STAND-BY button to turn the power on.
& STOP)
PLAYBACK (PLAY
MUSIC PORT
Load a cassette into the
TAPE 1 compartment or
TAPE 2 compartment
with the side to be played
facing toward you.
PHONES
MUSIC PORT
5
CD
4
3
PRESET
2
PRESET
1
TUNING
VOL.
TUNING
— VOL.
RECORD/PLAYBACK
PLAYBACK
(PLAY & STOP)
5
PHONES
4
AUDIO IN
3
2
1
TAPE 1
REMOTE
SENSOR
TIMER
POWER
ON/ STAND-BY
c
OPEN/
CLOSE
CD
5
4
Press the TAPE (1
want to listen to.
5
Press the / (TAPE
to start playback.
TAPE
(1
2)
4
TUNER
(BAND)
3
PRESET
TAPE 2
2) button to select the cassette you
PRESET
2
AUDIO
IN
1
TUNING
TUNING
VOL.
PLAYBACK (PLAY & STOP)
PHONES
AUDIO IN
VOL.
RECORD/PLAYBACK
)
Tape play indicator
Auto power on function:
When you press any of the following buttons, the unit turns on.
TAPE (1 2) button (main unit and remote control): The unit
turns on and the “TAPE” function is activated.
TAPE
button on the remote control: The unit turns on and the
“TAPE” function is activated.
/ button on the main unit: The unit turns on and playback of
the last function starts (CD, TAPE, TUNER, AUDIO IN).
Auto power off function:
In the stop mode of tape operation, the main unit enters the standby mode after 15 minutes of inactivity.
32
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
Various tape functions
Function
Main unit
Remote
control
Operation
Play
Press in the stop
mode.
Stop
Press in the playback,
fast forward or rewind
mode.
Fast
forward/
Fast rewind
(TAPE 2
only)
Press in the playback
or stop mode.
PRESET
PRESET
Caution:
To remove the cassette, press the button, and then open the
compartment.
Before changing from one tape operation to another, press the
button.
If a power failure occurs during tape operation, the tape head will
remain engaged with the tape and the cassette door will not open.
In this case, wait until the power is restored.
Before recording:
When recording important selections, make a preliminary test to
ensure that the desired material is properly recorded.
SHARP is not liable for damage or loss of your recording arising
from malfunction of this unit.
The volume and sound controls can be adjusted with no effect
on the recorded signal (Variable Sound Monitor).
For recording, use only normal tapes. Do not use metal or
CrO tapes.
Recording can be operated in the TAPE 2 compartment only.
The TAPE 1 is for playback only.
Erase-prevention tab of cassette tapes:
When recording on a cassette tape, make sure that the eraseprevention tabs are not removed. Cassettes have removable
tabs that prevent accidental recording or erasing.
To protect the recorded sound, remove the tab after recording.
Cover the tab hole with adhesive tape to record on the tape
without the tab.
CD-G14000
Tape Recording
Recording on a cassette tape
Side A
Tab for side B
Tab for side A
33
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
Recording on a cassette tape (continued)
Recording from a CD (or MP3 disc)
POWER
ON/ STAND-BY
1
2
3
5
4
3
2
1
c
CD
OPEN/
CLOSE
REMOTE
SENSOR
TIMER
POWER
ON/ STAND-BY
c
OPEN/
CLOSE
CD
5
TAPE
(1
2)
5
4
Press the ON/STAND-BY button to turn the power on.
Press the CD button.
Load a cassette into the TAPE 2 cassette compartment
with the side to be recorded on facing you.
Wind past the leader of the tape, on which recording cannot be
performed.
Press the
button.
4
TUNER
(BAND)
PRESET
Tape Recording
Recording will be paused.
3
PRESET
2
AUDIO
IN
1
TUNING
TUNING
VOL.
4
VOL.
3
PLAYBACK (PLAY & STOP)
PHONES
RECORD/PLAYBACK
2
AUDIO IN
1
5
Press one of the
disc.
6
Within 5 seconds, press the
1-
5 buttons to select the desired
/
button to start recording.
Recording is started from the selected CD. When the
playback of the last track is finished or the end of the tape is
reached, the CD and the cassette will stop automatically.
Playback of the disc will start approximately 7 seconds after
the tape starts.
To stop recording:
Press the button.
The CD and tape will stop.
34
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
To stop recording:
Press the button.
The disc and tape will stop.
Dubbing from tape to tape
You can record from TAPE 1 to TAPE 2.
1
2
Recording from the radio
1
2
3
Load a prerecorded
into the TAPE 1
compartment. Insert
tape into the TAPE 2
compartment.
cassette
cassette
a blank
cassette
Tune in to the desired station. (See page 30)
Press the TAPE (1
the display.
Press the
4
Press the
button.
Recording will be paused.
5
Press the
button.
button to start recording.
To interrupt recording:
Press the
button.
To resume recording, press the
/
3
button.
To stop recording:
Press the button.
Note:
If you hear a whistling noise while recording an AM station, move the
AM loop antenna.
2
1
TUNING
VOL.
TUNING
— VOL.
RECORD/PLAYBACK
PLAYBACK
(PLAY & STOP)
AUDIO IN
TAPE 1
3
/
4
PRESET
PRESET
TAPE 2
It is recommended that the recording tape is the same length as
the master tape.
Load a cassette into the TAPE 2 cassette compartment
with the side to be recorded on facing you.
Wind past the leader of the tape, on which recording cannot be
performed.
Press the
5
CD
PHONES
Recording will be paused.
4
Press the ON/STAND-BY button to turn the power on.
/
2) button until “TAPE 1” appears on
button to start dubbing.
To stop dubbing:
Press the button.
TAPE 1 and TAPE 2 will simultaneously stop.
Tape Recording
To perform programmed recording:
1 Program discs and tracks. (See page 25.)
2 Press the
button.
3 Press the / button.
Erasing recorded tapes
1
2
3
4
Load the tape to be erased into the TAPE 2 cassette
compartment with the side to be erased facing toward you.
Press the TAPE (1 2) button until “TAPE 2” appears on the
display.
Press the
button.
Press the / button to start erasing.
Note:
Make sure that the TAPE 1 is not in use.
35
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
Timer and sleep operation (Remote Control only)
Timer playback:
The unit turns on and plays the desired source (CD, MP3 disc, tuner,
tape) at the preset time.
Timer recording:
The unit turns on and starts recording from the tuner at the preset
time.
Advanced Features
This unit has 2 types of timer: ONCE TIMER and DAILY TIMER.
Once timer:
Once timer play and once timer recording works for
one time only at a preset time.
For example, if you are away but want to record a program on a
radio station.
Timer playback or timer recording
Before setting timer:
Daily timer:
Daily timer play and daily timer recording works at
the same preset time everyday.
For example, set the timer as a wake up call every morning.
Using the once timer and daily timer in combination:
For example, use the once timer to record a radio program, and use
the daily timer to wake up.
1 Set the daily timer (pages 36 - 38).
2 Set the once timer (pages 36 - 38).
1 minute or more
1
2
3
Press the ON/STAND-BY button to turn the power on.
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to select
“ONCE” or “DAILY”, and press the MEMORY button.
Once timer
Daily timer
Start
1 Check that the clock is set to the correct time (refer to page 19).
If it is not set, you cannot use the timer function.
2 For timer playback: Load a cassette or discs to be played.
For timer recording: Load a cassette for recording in the TAPE
2 cassette compartment.
Stop
Start
Stop
Note:
When the setting times for the daily timer and once timer overlap,
the once timer takes priority. Allow an interval of at least 1 minute
between operations.
Set the clock to the correct time if “ONCE” or “DAILY” does not
appear.
36
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
4
Within 10 seconds, press the
or
button to
select “ONCE SET” or “DAILY SET”, and press the
MEMORY button.
5
Press the
or
button to select “PLAY” or
“REC”, and press the MEMORY button.
White
9
Switch input with the
or
button, and then
press the MEMORY button.
To select the timer playback source: CD, TUNER, TAPE 1 or
TAPE 2.
To select the timer recording source: TUNER.
When you select the tuner, select a station by pressing the
or
button, and then press the MEMORY
button.
If a station has not been programmed, “NO PRESET” will
be displayed and timer setting will be canceled.
10
Adjust the volume using the VOLUME control, and then
press the MEMORY button.
Do not turn the volume up too high.
11
Press the ON/STAND-BY button to enter the power standby mode.
The “TIMER” indicator lights up and the unit is ready for timer
playback or timer recording.
Red
The illustrations show the daily timer setting.
6
Press the
or
button to adjust the hour and
then press the MEMORY button.
The illustrations show the timer playback setting in the daily
timer mode.
7
5
4
3
2
Advanced Features
CD-G14000
1
Press the
or
button to adjust the minutes and
then press the MEMORY button.
REMOTE
SENSOR
TIMER
POWER
ON/ STAND-BY
c
OPEN/
CLOSE
CD
5
TAPE
(1
2)
4
TUNER
(BAND)
3
PRESET
PRESET
2
AUDIO
IN
1
TUNING
TUNING
VOL.
8
VOL.
Set the time to finish as in steps 6 and 7 above.
Continued
to the next
continued
next page
page
37
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
Advanced Features
CD-G14000
Timer and sleep operation (Remote Control only) (continued)
12
When the preset time is reached, playback or recording
will start.
The volume will increase gradually until it reaches the preset
volume.
13
When the timer end time is reached, the system will enter
the power stand-by mode automatically.
Once timer:
The timer will be canceled.
Daily timer:
The timer will operate at the same time every day. It will
continue until the daily timer setting is canceled. Cancel the
daily timer when it is not used.
Note:
When performing timer playback or recording using another unit
connected to the AUDIO IN jacks, select “AUDIO IN” in step 9.
This unit will turn on or enter the power stand-by mode automatically,
however, the connected unit will not turn on or off.
Checking the timer setting in the timer stand-by mode:
1 Press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
“ONCE” or “DAILY”, and press the MEMORY button.
3 Within 10 seconds, press the
or
button to select
“ONCE CALL” or “DAILY CALL”, and press the MEMORY button.
The unit returns to the timer stand-by mode after displaying the
settings in order.
Canceling the timer setting in the timer stand-by mode:
1 Press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
“ONCE” or “DAILY”, and press the MEMORY button.
3 Within 10 seconds, press the
or
button to select
“ONCE OFF” or “DAILY OFF”, and press the MEMORY button.
Timer will be canceled (the setting will not be canceled).
Reusing the memorized timer setting:
The timer setting will be memorized once it is entered. To reuse the
same setting, perform the following operations.
1 Turn the power on and press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
“ONCE” or “DAILY”, and press the MEMORY button.
3 Within 10 seconds, press the
or
button to select
“ONCE ON” or “DAILY ON”, and press the MEMORY button.
4 Press the ON/STAND-BY button to enter the power stand-by
mode.
38
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
The radio, CD, MP3 disc and cassette tape can all be turned off
automatically.
1
2
3
4
Play back the desired sound source.
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to select
“SLEEP”, and press the
MEMORY button.
Press the
or
button to select the time.
(Maximum: 3 hours - Minimum: 1 minute)
3 hours - 5 minutes 5-minute intervals
5 minutes - 1 minute 1-minute intervals
5
Press the MEMORY button.
“SLEEP” will appear.
6
The unit will enter the power stand-by mode automatically
after the preset time has elapsed.
The volume will be turned down 1 minute before the sleep
operation finishes.
To confirm the remaining sleep time:
1 While “SLEEP” is indicated, press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
“SLEEP X : XX”.
“X : XX” is sleep remaining time.
The remaining sleep time is displayed for about 10 seconds.
You can change the remaining sleep time while it is displayed by
pressing the MEMORY button (steps 4 - 5).
To cancel the sleep operation:
Press the ON/STAND-BY button while “SLEEP” is indicated.
To cancel the sleep operation without setting the system to the
stand-by mode, proceed as follows.
1 While “SLEEP” is indicated, press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
“SLEEP OFF”, and press the MEMORY button.
To use timer and sleep operation together
Sleep and timer playback:
For example, you can fall asleep listening to the radio and wake up
to CD in the next morning.
Sleep and timer recording:
For example, you can fall asleep listening to the CD and record radio
programs while sleeping.
1
2
Set the sleep time (see left, steps 1 - 5).
While the sleep timer is set, set the timer playback or recording
(steps 2 - 10, pages 36 - 37).
Sleep timer setting
Timer playback or
recording setting
1 minute - 3 hours
Sleep operation will
automatically stop.
Advanced Features
Sleep operation
End time
Desired time
Timer playback or recording
start time
Caution:
When using the cassette deck, be sure the tape length is long
enough to perform both functions. If you want to sleep and wake up
listening to a tape, and the length of the tape is shorter than the sleep
timer setting, timer playback or recording will not be possible.
39
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
Enhancing your system
The connection cord is not included. Purchase a commercially
available cord as shown below.
Portable audio
player, etc.
5
4
3
2
1
AUDIO IN
To the line output jack
REMOTE
SENSOR
TIMER
POWER
ON/ STAND-BY
c
OPEN/
CLOSE
CD
Listening to sounds of Portable Audio Player,
etc.
1
Connect a Portable Audio Player etc. to the front AUDIO IN
jack.
2
3
4
Press the ON/STAND-BY button to turn the power on.
Press the AUDIO IN button.
Play the connected equipment.
5
TAPE
TAPE
(1 (12) 2)
Advanced Features
4
TUNER
(BAND)
You can enjoy sounds from the supplied speakers.
3
PRESET
PRESET
2
AUDIO
IN
1
TUNING
TUNING
VOL.
VOL.
Note:
To prevent noise interference, place the unit away from the television.
PLAYBACK (PLAY & STOP)
PHONES
AUDIO IN
Audio cable
(not supplied)
RECORD/PLAYBACK
Auto power on function:
When you press any of the following buttons, the unit turns on.
AUDIO IN button (main unit and remote control): The unit turns
on and the “AUDIO IN” function is activated.
/ button on the main unit: The unit turns on and playback of
the last function starts (CD, TAPE, TUNER, AUDIO IN).
To record sounds of Portable Audio Player, etc.
1
Insert a cassette in the TAPE 2 cassette compartment.
2
Press the AUDIO IN button.
3
Press the
4
Press the
5
Play the Portable Audio Player, etc.
button.
/
button.
40
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
Troubleshooting chart
Before plugging in or unplugging the headphones, reduce the
volume.
Be sure your headphones have a 1/8" (3.5 mm) diameter plug and
impedance between 16 and 50 ohms. The recommended
impedance is 32 ohms.
Plugging in the headphones disconnects the speakers
automatically. Adjust the volume using the VOLUME control.
5
4
3
2
1
REMOTE
SENSOR
TIMER
POWER
ON/ STAND-BY
c
OPEN/
CLOSE
CD
5
TAPE
(1
2)
4
TUNER
(BAND)
3
PRESET
PRESET
2
AUDIO
IN
1
TUNING
TUNING
VOL.
PLAYBACK (PLAY & STOP)
PHONES
AUDIO IN
VOL.
Many potential problems can be resolved by the owner without
calling a service technician.
If something is wrong with this product, check the following before
calling your authorized SHARP dealer or service center.
General
Symptom
Possible cause
The clock is not set to the Did a power failure occur? Reset
correct time.
the clock. (Refer to page 19.)
When a button is pressed, Set the unit to the power stand-by
the unit does not respond.
mode and then turn it back on.
If the unit still malfunctions, reset
it. (Refer to page 43.)
No sound is heard.
Is the volume level set to “0”?
Are the headphones connected?
Are the speaker wires
disconnected?
RECORD/PLAYBACK
CD player
References
Headphones
CD-G14000
Symptom
Possible cause
Playback does not start.
Is the disc loaded upside down?
Playback stops in the
Does the disc satisfy the
middle or is not performed
standards?
properly.
Is the disc distorted or
scratched?
Playback sounds are
Is the unit located near excessive
skipped, or stopped in the
vibrations?
middle of a track.
Is the disc very dirty?
Has condensation formed inside
the unit?
41
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
Troubleshooting chart (continued)
Tuner
Cassette deck
Symptom
Cannot record.
References
Possible cause
Is the erase-prevention tab
removed?
Cannot record tracks with Is it a normal tape? (You cannot
proper sound quality.
record on a metal or CrO tape.)
Cannot erase completely.
Sound skipping.
Is there slack in the tape?
Cannot hear treble.
Is the tape stretched?
Sound fluctuation.
Are the capstans, pinch rollers, or
heads dirty?
Cannot remove the tape. If a power failure occurs during
playback, the heads remain
engaged with the tape. Do not
open the compartment with great
force.
Symptom
The radio makes unusual
noises continuously.
Possible cause
Is the unit placed near the TV or
computer?
Is the FM antenna or AM loop
antenna placed properly? Move
the antenna away from the AC
power cord if it's located nearby.
Condensation
Sudden temperature changes, storage or operation in an extremely
humid environment may cause condensation inside the cabinet (CD
pickup, tape heads, etc.) or on the transmitter on the remote control.
Condensation can cause the unit to malfunction. If this happens,
leave the power on with no disc (or cassette) in the unit until normal
playback is possible (about 1 hour). Wipe off any condensation on
the transmitter with a soft cloth before operating the unit.
Remote control
Symptom
The remote control does
not operate.
Possible cause
Is the AC power cord of the unit
plugged in?
Is the battery polarity correct?
Are the batteries dead?
Is the distance or angle
incorrect?
Does the remote control sensor
receive strong light?
42
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
If trouble occurs
Before transporting the unit
When this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal supply
voltage due to lightning, etc.) or if it is operated incorrectly, it may
malfunction.
Remove all CDs from the unit. Make sure there is no CD in the disc
tray. Then, set the unit to the power stand-by mode. Carrying the unit
with discs left inside can damage the unit.
Note:
If neither operation above restores the unit, clear all the memory by
resetting it.
Clearing all the memory (reset)
1
2
Press the ON/STAND-BY button to enter the power stand-by
mode.
While pressing down the button and the button, press the CD
button until “CLEAR ALL” appears.
CD
Care of compact discs
Compact discs are fairly resistant to damage, however mistracking
can occur due to an accumulation of dirt on the disc surface. Follow
the guidelines below for maximum enjoyment from your CD
collection and player.
Do not write on either side of the disc, particularly the non-label
side from which signals are read. Do not mark this surface.
Keep your discs away from direct sunlight, heat, and excessive
moisture.
Always hold the CDs by the edges. Fingerprints, dirt, or water on
the CDs can cause noise or mistracking. If a CD is dirty or does
not play properly, clean it with a soft, dry cloth, wiping straight out
from the center, along the radius.
NO
YES
Correct
References
If such a problem occurs, do the following:
1 Set the unit to the stand-by mode and turn the power on again.
2 If the unit is not restored in the previous operation, unplug and
plug in the unit, and then turn the power on.
Caution:
This operation will erase all data stored in memory including clock,
timer settings, tuner preset, and CD program.
43
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
Maintenance
Cleaning the tape-handling parts
Dirty heads, capstans or pinch rollers can cause poor sound and
tape jams. Clean these parts with a cotton swab moistened with
commercial head/pinch roller cleaner or isopropyl alcohol.
When cleaning the heads, pinch rollers, etc., unplug the unit which
contains high voltages.
A
TAPE 1
B
C
Cleaning the CD pickup lens
In order to ensure proper operation of the CD player, preventative
maintenance (cleaning of the laser pickup lens) should be
performed periodically. Lens cleaners are commercially available.
Contact your local CD software dealer for options.
Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth and a diluted soap
solution, then with a dry cloth.
5
4
3
2
1
REMOTE
SENSOR
TIMER
POWER
ON/ STAND-BY
5
CD
4
3
PRESET
PRESET
References
D
2
1
TUNING
VOL.
TUNING
VOL.
E B
C
TAPE 2
Caution:
Do not use chemicals for cleaning (gasoline, paint thinner, etc.). It
may damage the cabinet finish.
Do not apply oil to the inside of the unit. It may cause malfunctions.
RECORD/PLAYBACK
PLAYBACK
(PLAY & STOP)
AUDIO IN
PHONES
Playback head
Capstan
Pinch roller
Erase head
Recording/Playback head
After long use, the deck's heads and capstans may become
magnetized, causing poor sound. Demagnetize these parts once
every 30 hours of playing/recording time by using a commercial
tape head demagnetizer. Read the demagnetizer's instructions
carefully before use.
44
08/1/15
CD-G14000_EN.fm
TINSEA128AWZZ
Specifications
Amplifier
Output power
Front speakers
General
Power source
AC 120 V ~ 60 Hz
Power consumption
98 W
Dimensions
Width: 10-1/4" (260 mm)
Height: 13" (332 mm)
Depth: 12-7/8" (324 mm)
Weight
Output terminals
16 lbs. (7.3 kg)
CD player
Input terminals
Type
5-disc multi-play compact disc player
Signal readout
Non-contact, 3-beam semiconductor laser
pickup
D/A converter
Multi bit D/A converter
FTC: 115 watts minimum RMS per
channel into 6 ohms from 100 Hz to
20 kHz, 10% total harmonic
distortion
Front speakers: 6 ohms
Headphones: 16 - 50 ohms
(recommended: 32 ohms)
Subwoofer pre-out (audio signal):
200 mV/10 k ohms at 70 Hz
AUDIO IN:
250 mV/47 k ohms
Tuner
Frequency range
Frequency response 20 - 20,000 Hz
Dynamic range
RMS: Total 280 watts
(140 watts per channel into 6 ohms
at 1 kHz, 10% total harmonic
distortion)
References
As part of our policy of continuous improvement, SHARP reserves
the right to make design and specification changes for product
improvement without prior notice. The performance specification
figures indicated are nominal values of production units. There may
be some deviations from these values in individual units.
CD-G14000
FM: 87.5 - 108.0 MHz
AM: 530 - 1,720 kHz
90 dB (1 kHz)
45
08/1/17
CD-G14000_EN.fm
TINSEA128AWZZ
CD-G14000
Specifications (continued)
Cassette deck
Active subwoofer
Frequency response 50 - 14,000 Hz (normal tape)
Signal/noise ratio
55 dB (TAPE-1 playback)
50 dB (TAPE-2 recording/playback)
Wow and flutter
0.3 % (WRMS)
Power source
Power
consumption
Output power
Front speaker
References
Type
Maximum input
power
Rated input power
Impedance
Dimensions
Weight
2-way type speaker system
2" (5 cm) tweeter x 1
6-5/16" (16 cm) woofer x 1
230 W
115 W
6 ohms
Width: 7-7/8" (200 mm)
Height: 15-3/4" (400 mm)
Depth: 8-11/16" (221 mm)
18.17 lbs. (8.24 kg)
Input terminals
Speaker type
Impedance
Dimensions
Weight
AC 120 V ~ 60 Hz
105 W
RMS: 320 watts into 6 ohms at 70 Hz,
10% total harmonic distortion
FTC: 300 watts minimum RMS into 6 ohms
from 50 Hz to 120 Hz, 10% total
harmonic distortion
Subwoofer input (audio signal):
200mV / 10 k ohms at 70 Hz
10" (25 cm) woofer
6 ohms
Width: 18-1/8" (460 mm)
Height: 15-3/4" (400 mm)
Depth: 15-1/8" (384 mm)
42.2 lbs. (19.14 kg)
46
08/1/17
CD-G14000_EN.fm
TINSEA128AWZZ
MEMO
z
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof
with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has
been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in
design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING
THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any
warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser.
Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the
purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event
shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone
other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states
do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
Model Specific Section
Your Product Model Number & Description:
CD-G14000 Mini Component System
(Be sure to have this information available when you need service for your Product.)
Warranty Period for this Product:
One (1) year parts and labor from the date of purchase.
Additional Item(s) Excluded from Warranty Coverage (if any): Non-functional accessories, supplies, and consumable items.
Where to Obtain Service:
At a Sharp Authorized Servicer located in the United States.
To find a location of the nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-BE-SHARP.
What to do to Obtain Service:
Ship prepaid or carry in your Product to a Sharp Authorized Servicer.
Be sure to have Proof of Purchase available. If you ship the Product, be sure it is insured and
packaged securely.
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP.
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430
08/1/28
CD-G14000_BACK.fm
Printed in Malaysia
TINSEA219AWZZ
08B R MW 1
TINSEA128AWZZ