Memorex MMG-CR3810 Operating instructions

MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 21
UNDERCABINET CD CLOCK RADIO
MODEL: MMG-CR3810
BEFORE OPERATING THIS PRODUCT,
PLEASE READ THESE INSTRUCTIONS COMPLETELY.
OPERATING INSTRUCTIONS
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 1
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle is intended to alert the user to the
presence of uninsulated ‘dangerous voltage’ within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
DANGER:
Invisible and hazardous laser radiation when open and
interlock failed or defeated. Avoid direct exposure to beam.
FCC WARNING:
This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the
modifications are expressly approved in the instruction manual. The user
could lose the authority to operate this equipment if an unauthorized
change or modification is made.
LASER SAFETY: This unit employs a laser. Only qualified service personnel
should attempt to service this device due to possible eye injury.
CAUTION: USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE PROCEDURE HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
SURGE PROTECTORS:
It is recommended to use a surge protector for AC connection. Lightning
and power surges ARE NOT covered under warranty for this product.
1
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 2
INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT SAFETY INSTRUCTIONS
Before using the unit, be sure to read all operating
instructions carefully. Please note that these are
general precautions and may not pertain to your
unit. For example, this unit may not have the
capability to be connected to an outdoor antenna.
1. READ INSTRUCTIONS
All the safety and operating instructions should be
read before the product is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be
retained for future reference.
3. HEED WARNINGS
All warnings on the product and in the operating
instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be
followed.
5. CLEANING
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. ATTACHMENTS
Do not use attachments not recommended by the
product's manufacturer as they may cause
hazards.
7. WATER AND MOISTURE
Do not use this product near water- for example,
near a bathtub, washbowl, kitchen sink, or
laundry tub, in a wet basement, or near a
swimming pool.
8.
ACCESSORIES
Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may
fall, causing serious injury and serious damage to
the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the
manufacturer or sold with the product. Any
mounting of the product should follow the
manufacturer’s instructions, and should use a
mounting accessory recommended by the
manufacturer.
8A. An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance
and cart combination to overturn.
9. VENTILATION
Slots and openings in the cabinet and in the back
or bottom are provided for ventilation and to
ensure reliable operation of the product and to
protect it from overheating. These openings must
not be blocked or covered. The openings should
never be blocked by placing the product on a
bed, sofa, rug, or other similar surface. This
product should never be placed near or over a
radiator or heat source. This product should not
be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is
provided or the manufacturer's instructions have
been adhered to.
PORTABLE CART WARNING
(symbol provided by RETAC)
2
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 3
IMPORTANT SAFETY INSTRUCTIONS (CONTINUED)
10. POWER SOURCES
This product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply to your home, consult your appliance
dealer or local power company. For products
intended to operate from battery power, or other
sources, refer to the operating instructions.
11. GROUNDING OR POLARIZATION
This product is equipped with a polarized
alternating-current line plug (a plug having one
blade wider than the other). This plug will fit into
the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully
into the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles,
and the point where they exit from the appliance.
13. LIGHTNING
To protect your product from a lightning storm, or
when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will
prevent damage to the product due to lightning
and power-line surges.
14. POWER LINES
An outside antenna system should not be located
in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall
into such power lines or circuits. When installing
an outside antenna system, extreme care should
be taken to keep from touching such power lines
or circuits as contact with them might be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords
as this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short out parts that could result in
fire or electric shock. Never spill or spray any type
of liquid on the product.
17. SERVICING
Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
18. REPLACEMENT PARTS
When replacement parts are required, be sure
the service technician uses replacement parts
specified by the manufacturer or those that have
the same characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock or other hazards.
19. SAFETY CHECK
Upon completion of any service or repairs to this
product, ask the service technician to perform
safety checks to determine that the product is in
proper operating condition.
20. WALL OR CEILING MOUNTING
The product should be mounted to a wall or
ceiling only as recommended by the
manufacturer.
21. DAMAGE REQUIRING SERVICE
Unplug the product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as an adjustment of other controls
may result in damage and will often require
extensive work by a qualified technician to restore
the product to its normal operation.
e. If the product has been dropped or the cabinet
has been damaged.
f. When the product exhibits a distinct change in
performance - this indicates a need for service.
22. HEAT
The product should be situated away from heat
sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that
produce heat.
23. NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV
system installer's attention to Article 820-40 of the
NEC that provides guidelines for proper
grounding and, in particular, specifies that the
cable ground shall be connected to the grounding
system of the building, as close to the point of
cable entry as practical.
24. NONUSE PERIODS
The power cord of the appliance should be
unplugged from the outlet when left unused for a
long period of time.
3
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 4
Dear Customer:
Selecting fine audio equipment such as the unit you’ve just purchased is only the start of your
musical enjoyment. Now it’s time to consider how you can maximize the fun and excitement
your equipment offers. This manufacturer and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of your equipment by playing it at a
safe level. One that lets the sound come through loud and clear without annoying blaring or
distortion and, most importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes of
sound. So what sounds “normal” can actually be loud and harmful to your hearing. Guard
against this by setting your equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, and without
distortion.
Once you have established a comfortable sound level:
• Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future. After
all, we want you listening for a lifetime.
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often undetectable until it is too late, this manufacturer and
the Electronic Industries Association’s Consumer Electronics Group recommend you avoid
prolonged exposure to excessive noise. This list of sound levels is included for your protection.
30
40
50
60
70
80
Decibel
Example
Level
Quiet library, soft whispers
Living room, refrigerator, bedroom away from traffic
Light traffic, normal conversation, quiet office
Air conditioner at 20 feet, sewing machine
Vacuum cleaner, hair dryer, noisy restaurant
Average city traffic, garbage disposals, alarm clock at two feet
THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT EXPOSURE:
Subway, motorcycle, truck traffic, lawn mower
Garbage truck, chain saw, pneumatic drill
Rock band concert in front of speakers, thunderclap
Gunshot blast, jet engine
Rocket launching pad
Information courtesy of the Deafness Research Foundation.
E L E CT
I N
D
U
EIA
EST. 1924
S
S
O
C I A T
R I E S
4
I C
T
LISTENING
For A Lifetime
A
We
Want You
N
S
R
O
N
90
100
120
140
180
I
O
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 5
POWER SOURCE
Unravel the AC cord and connect it to a
conveniently located AC outlet having 120V and
60Hz only. The Clock Display will blink.
AC Outlet
NOTE: The AC plug supplied with the unit is
polarized to help minimize the possibility of
AC Plug
electric shock. If the AC plug does not fit into a
nonpolarized AC outlet, do not file or cut the wide blade. It is the user’s
responsibility to have an electrician replace the obsolete outlet.
LOCATION OF CONTROLS
1
2 34
5 6 7
8
9 1011 12
4.
5.
6.
7.
8.
13 14 151617 18 19
AC Cord (Rear of Unit)
10. STOP (■) Button
Remote Sensor
11. SKIP/TUNING
/
Buttons
Mounting Screw Holes (Top of 12. OPEN/CLOSE Button
Unit)
13. POWER Button
RADIO/BAND Button
14. DISPLAY Button
CD Button
15. MEMORY/CLOCK SET Button
CD Compartment Door
16. Remote Stand
Display
17. MEMORY DOWN/RANDOM
TIMER Button
Button
9.
PLAY/PAUSE (
1.
2.
3.
) Button
18. MEMORY UP/REPEAT Button
19. VOLUME +/– Buttons
5
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 6
LOCATION OF CONTROLS (CONTINUED)
1
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
12
2
3
4
5
6
7
8
9
10
11
13
14
15
16
17
18
OPEN/CLOSE Button
Number Buttons
OVER Button
STOP (■) Button
PLAY/PAUSE (
) Button
SKIP/TUNING
Button
SKIP/TUNING
Button
MEM DOWN/ RANDOM Button
MEM UP/REPEAT Button
TUNER/BAND Button
CD Button
POWER Button
MUTE Button
VOLUME +/– Buttons
MEM/CLOCK SET Button
TIMER Button
DISPLAY Button
Battery Compartment (Rear)
BATTERY INSTALLATION
-
+
+
-
BATTERY INSTALLATION
The remote control transmitter is designed to operate
with two (2) “AAA” size batteries (not included). To install
the batteries, slide the battery compartment cover open
on the back of the remote control and insert two (2)
“AAA” size batteries observing the polarity (see figure to
the right). Replace the battery compartment cover.
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the
battery compartment. Reversed batteries may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old
batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent
damage or injury from possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and
rupture. (Follow battery manufacturer’s directions.)
6
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 7
MOUNTING
This under the cabinet CD clock radio has been designed to be installed
underneath a wooden cabinet by using the Mounting Template, four (4) Screws,
four (4) Washers and four (4) Spacers (see Figure 1).
Mounting Template
Screws (4 of each size)
2-3/4" and 1-5/8"
Spacers (4 of each size)
1"
1/2"
4 Washers
1/4"
Figure 1
MOUNTING THE UNIT
Locate a desired space for the CD clock radio (it is recommended to mount the
unit at the front edge of the cabinet) and follow the instructions below and on the
next few pages to mount.
1. Empty the contents of the cabinet where the unit will be mounted. Clean
under the cabinet before mounting.
NOTE: For optimal mounting, the screws must go into the unit to a depth of at
least 3/8”. If the overall length from the bottom of the cabinet shelf to the bottom
of the overhang is more than 1-3/4”, a wood shim must be used. A shim can be
made from a small sheet of plywood, using the template to locate the central lines
for drilling 1/4” mounting holes. The shim can be located between the cabinet
shelf bottom and spacers. Make sure the shim is at least as thick as the excess
over 1-3/4”. If a shim is necessary, longer screws are required. Longer screws
(type #10-32) are available at most hardware stores.
2. Cut out the template on the line indicated on the template. The template size
and screw hole positions are identical to the top of the unit.
3a. IF YOUR CABINET DOES NOT HAVE AN OVERHANG:
Position the template
in the desired location
underneath the
cabinet, flush with the
front edge. Then, tape
the template in place
(see Figure 2), and
continue to step 4.
Template
Figure 2
7
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 8
MOUNTING (CONTINUED)
3b. IF YOUR CABINET HAS AN OVERHANG:
Measure the thickness of
the overhang (see Figure
3). Fold the front of the
template down along the
printed guideline that is
closest to the thickness of
your cabinet. Tape the
Measure Thickness
folded portion to the
of Cabinet Overhang
backside of the overhang,
Figure
3
then tape the template
underneath the cabinet (see
Figure 4).
NOTE: If the cabinet has glue
blocks or other obstructions, cut
out corresponding areas on the
template to clear them. Do not
cut through the screw holes
Template
Fold at
indicated on the template.
Dotted Line
4. Drill 1/4” diameter holes
Figure 4
underneath the cabinet
using the four points marked on the template.
TIPS:
• On a wooden cabinet, you may want to mark and start the drill holes with a nail
or an awl.
• Make sure to hold the drill very firmly against the cabinet to reduce “walking” of
the drill bit from the markers.
• Use masking tape above the hole locations on the inside of the cabinet to
reduce splintering.
• If installing the unit under a wood cabinet, you may wish to countersink the
drilled holes from the inside. This will eliminate the use of washers and allow
the screwheads to be flush with the floor of the cabinet. If you cannot
countersink the holes, use the supplied washers.
• Always wear goggles.
• DO NOT mount above a sink or stove.
5. Remove the template and clean the drill shavings from inside and
underneath the cabinet.
6. If your cabinet does not have an overhang, skip this step.
If your cabinet has an overhang, select the spacer or combination of
spacers that is equal to or longer than the cabinet overhang (see Figure 5 on
the next page).
8
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 9
MOUNTING (CONTINUED)
7.
Insert screws from the
INSIDE of the cabinet. The
washers must be used on
metal cabinets and wood
cabinets if the drilled holes
were not countersunk.
Position the washers, flatside down, and insert the
screws into the holes.
8.
If your cabinet does not
have an overhang, skip
this step.
If your cabinet has an
overhang, hold the
SELECT SCREWS WHICH MEET MINIMUM, BUT DO NOT
EXCEED MAXIMUM LENGTH
Figure 5
Mounting Screws
screwheads down while you
push the selected spacers
upward onto the screws
under the cabinet. Make
sure to push up spacers
until they are firmly against
the cabinet bottom and/or
fully nested (if more than
one are used).
9. Align the unit under the
screws. Hold the unit so its
mounting screw holes (on
the top of the unit) are
against the mounting
screws (see Figure 6) , then
partially tighten the screws.
NOTE: Do not fully tighten until
all 4 screws have been started.
Figure 6
The top edge of the unit should
clear the overhang.
10. Extend the cord towards the AC outlet (see page 5) and secure it by using
cord hooks (not supplied) to keep the cord out of the way. For more attractive
appearance, place the cord hooks at the back edge of the cabinet, directly
over the AC outlet. It is recommended that the line cord be fully extended for
best FM reception.
11. Connect the Remote Stand to the bottom of the unit by sliding it towards the
rear of the unit.
9
Washers
Spacers
or or
or or
or or
Spacers
or or
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 10
OPERATION
TO SET OR RESET THE ACTUAL TIME
1
2
1
2
When the unit is off, press the
MEMORY/CLOCK SET button.
1
Press the SKIP/TUNING
/
buttons ❶ to set the hour, then press the
MEMORY/CLOCK SET button ❷. Press
the SKIP/TUNING
/
buttons ❶
to set the minutes, then press the
MEMORY/CLOCK SET button ❷ again.
TO SET THE COUNTDOWN TIMER
1
2
1
2
2
1
2
2
Press the TIMER button ❶ again and
the minute digits will blink. Use the
SKIP/TUNING
/
buttons ❷ to
select the amount of minutes in the
countdown. Press the TIMER button ❶
to return to the actual time.
Press and hold the TIMER button ❶;
the display will show “00:00” and the
hour digits will blink. Use the
SKIP/TUNING
/
buttons ❷ to
select the amount of hours in the
countdown.
IMPORTANT NOTE ON THE COUNTDOWN TIMER:
The above procedure will set the amount of time that the timer will countdown
EVERY TIME THE TIMER IS PRESSED. To activate the countdown timer, or to
change the countdown timer, see the following page.
10
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 11
OPERATION (CONTINUED)
TO START THE COUNTDOWN TIMER
1
2
Once the countdown time has been
entered (see previous page), press
the TIMER button and the display will
start counting down the preset
countdown time.
When the countdown timer reaches
“00:00:oo”, the unit will beep. Press
the TIMER button again to turn off the
beeps.
NOTES:
• During the countdown, if you press the TIMER button again, the countdown
timer will revert back to the original timer.
• If no countdown time has been set as shown on the previous page, and the
TIMER button is pressed and released, the unit will turn on and beep.
• After the countdown timer has gone off, each subsequent press of the
TIMER button will set the countdown timer for the time as previously set. To
change the countdown timer time to a different time, simply repeat the
instructions on the previous page (“TO SET THE COUNTDOWN TIMER”).
• When the countdown timer is counting down, press the DISPLAY button to
cycle from the clock to the timer.
11
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 12
OPERATION (CONTINUED)
TO LISTEN TO THE RADIO
1
2
1
2
1
2
Press the POWER button ❶ to turn
the unit on. Press the RADIO/BAND
button once ❷ to select radio.
Repeatedly press to select the desired
band (AM, FM).
1
2
Tune a station by pressing the
SKIP/TUNING
or
button ❶.
To scan for strong station(s), press
and hold the the SKIP/TUNING
or
button ❶; the unit will then scan
and stop on the next strong station.
Adjust the volume using the VOLUME
+/– buttons ❷ .
Antennas
FM: Extend the AC cord for better FM reception.
AM: Turn the unit for better AM reception.
SETTING RADIO PRESETS (UP TO 20 PRESETS)
1
2
1
2
3
2
2
1
Turn the unit on and press the
RADIO/BAND button ❶ to select radio
and band. Press the SKIP/TUNING
or
button ❷ to find the
desired station.
Press the MEM/CLOCK SET button ❶
to confirm. Then select the Memory
Preset (up to 20) using the Number
buttons ❷. Simply press the Number
buttons ❷ to directly enter the Memory
Preset. For Memory Presets over 9,
press the OVER button ❸, followed by
the Number buttons ❷ (i.e. to select
12, press the OVER button, followed
by “1” then “2”).
12
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 13
OPERATION (CONTINUED)
TO RECALL MEMORY PRESETS
1
MUTE
1
3
4
2
2
1
1
2
To recall the Memory Presets, simply
press the MEMORY UP/REPEAT
button ❶ or MEMORY DOWN/
RANDOM button ❷, or directly select
them using the Number buttons ❸. For
Memory Presets over 9, press the
OVER button ❹ , followed by the
Number buttons ❸ (i.e. to select 12,
press the OVER button, followed by
“1” then “2”).
To temporarily mute the sound, press
the MUTE button ❶ on the remote, the
sound will be muted. Press the MUTE
button ❶ again or one of the VOLUME
+/– buttons ❷ to restore the sound.
DISPLAY
TO INSERT A CD
1
1
Pressing the DISPLAY button will
cycle the display as follows:
1st press: Clock
2nd press: Timer
3rd press: CD or Radio display
Open the CD compartment door by
pressing the OPEN/CLOSE button.
Insert a disc, label side up, onto the
spindle and close the CD
compartment door.
13
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 14
OPERATION (CONTINUED)
TO PLAY A CD
1
2
1
2
Insert a CD as described on the
previous page. Press the POWER
button ❶ to turn the unit on and press
the CD button ❷. The total playing
time and number of tracks will appear
in the display.
Press the PLAY/PAUSE (
) button
to start playback; the Play indicator
will appear. TO PAUSE PLAYBACK,
press the PLAY/PAUSE (
) button
again; the display will blink and the
Pause indicator will appear. Press
again to resume playback.
3
4
2
1
To skip forward or backward through
the tracks on the disc, press the CD
SKIP/TUNING
or
button. To
search forward or backward through
the tracks on the disc, press and hold
the SKIP/TUNING
or
button.
1
Adjust the volume using the VOLUME
+/– buttons ❶ as desired. When the
disc is through playing, it will stop.
Press the STOP (■) button ❷ to stop
the disc before it is finished.
FAQS: Do I need an adapter to play 3” singles?
No, simply insert the 3” single into the groove.
What is the maximum time for a CD in this unit?
The maximum time is 74 minutes.
NOTES:
• If a disc is inserted incorrectly, dirty, damaged or not present at all, the
display will show “no dISC”
• To remove the CD, press the OPEN/CLOSE button and remove the CD.
• Most buttons are both on the main unit and the remote control.
14
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 15
OPERATION (CONTINUED)
DIRECT TRACK ACCESS
1
When a CD is playing, simply press
the Number buttons ❶ to directly
select a track. For tracks over 9, press
the OVER button ❷, followed by the
Number buttons ❶ (i.e. to select track
12, press the OVER button, followed
by “1” then “2”.
1
2
TO REPEATEDLY PLAY BACK ONE TRACK
1
2
1
2
2
1
3
Press the POWER button ❶ to turn
the unit on and press the CD button ❷.
Press the MEMORY UP/REPEAT
button ❸ twice; Repeat ONE will
appear in the display.
3
1
Press the SKIP/TUNING
or
button ❶ to select a track. Press the
PLAY/PAUSE (
) button ❷ to start
playback and the unit will play the
same track over and over until the
STOP ( ) button ❸ is pressed.
TO REPEATEDLY PLAY BACK ALL TRACKS ON A CD
1
2
1
2
1
3
Press the POWER button ❶ to turn
the unit on and press the CD button ❷.
Press the MEMORY UP/REPEAT
button ❸ once; Repeat ALL will appear
in the display.
2
Press the PLAY/PAUSE (
) button
❶ to start playback and the unit will
then play all the tracks on the CD over
and over until the STOP ( ) button ❷
is pressed.
15
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 16
OPERATION (CONTINUED)
TO RANDOMLY PLAY BACK TRACKS ON A CD
1
2
1
2
1
3
2
Press the POWER button ❶ to turn
the unit on and press the CD button ❷.
Press the MEMORY DOWN/RANDOM
button ❸; “RANDOM” will appear in the
display.
2
Press the PLAY/PAUSE (
) button
❶ to begin playback. The unit will play
all the tracks in random order. Adjust
the volume using the VOLUME +/–
buttons ❷ as desired. When all the
tracks have been played, the unit will
stop.
TO PROGRAM THE MEMORY (UP TO 30 TRACKS)
1
2
1
2
1
2
3
Press the POWER button ❶ to turn
the unit on and press the CD button ❷.
Press the MEMORY/CLOCK SET
button ❸; “P-01” will appear indicating
the program number, “00” will appear
indicating the track number and and
“MEMORY” will blink in the display.
1
Select the first track to be played back
using the SKIP/TUNING
or
button
❶,
then
press
the
MEMORY/CLOCK SET button ❷
again. Repeat this step to program
additional tracks up to a maximum of
30 tracks.
Programming continued on the next page.
16
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 17
OPERATION (CONTINUED)
3
4
2
1
1
Adjust the volume using the VOLUME
+/– buttons ❶ as desired. When the
disc is through playing, it will stop.
Press the STOP (■) button ❷ to stop
the disc before it is finished.
Press the PLAY/PAUSE (
) button
to begin playback. The unit will play all
the tracks in the order you
programmed them.
5
NOTES:
• Press the STOP ( ) button to stop
the disc before it is finished.
• Programming is the ability to
preselect the order in which a
series of tracks will be played.
• If you attempt to program more
than 30 tracks, “FULL” will appear
in the display.
To skip forward or backward through
the programs, press the SKIP/TUNING
or
button. When the disc is
through playing, it will stop.
FAQ:
Can I program a track more than once?
Each track may be stored in the program memory as many times as desired
(up to 30 tracks).
17
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 18
CARE AND MAINTENANCE
Caring for Compact Discs
• Treat the disc carefully. Handle the compact
disc only by its edges. Never allow your
fingers to come in contact with the shiny,
unprinted side of the disc.
• Do not attach adhesive tape, stickers, etc.
to the compact disc label.
• Clean the compact disc periodically with a soft, lint-free, dry cloth. Never use
detergents or abrasive cleaners to clean the disc. If necessary, use a CD cleaning kit.
• If a compact disc skips or gets stuck on a section of the compact disc, it is
probably dirty or damaged (scratched).
• When cleaning the compact disc, wipe in straight lines from the center of the
compact disc to the outer edge of the compact disc. Never wipe in circular motions.
B ENZEN E
C LE A N E R
• This unit is designed to play only compact discs bearing the
COMPACT
identification logo as shown here. Other discs may not conform to
the CD standard and may not play properly.
DIGITAL AUDIO
• Compact Discs should be stored in their cases after each use to
avoid damage.
• Do not expose compact discs to direct sunlight, high humidity, high
temperatures, or dust, etc. Prolonged exposure or extreme temperatures can
warp the disc.
• Do not stick or write anything on either side of the disc. Sharp writing
instruments, or the ink may damage the surface.
Cleaning the unit
• To prevent fire or shock hazard, disconnect your unit from the AC power
source when cleaning.
• The finish on your unit may be cleaned with a dust cloth and cared for as other
furniture. Use caution when cleaning and wiping the plastic parts.
• Mild soap and a damp cloth may be used on the front panel.
18
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 19
TROUBLESHOOTING GUIDE
If you experience a problem with this unit, check the chart below before
calling for service.
SYMPTOM
Unit will not
turn on.
Disc will not play.
CAUSE
AC cord not
connected.
CD compartment
not closed.
Disc inserted
incorrectly.
Dirty or defective disc.
Moisture
condensation on disc.
No sound.
Volume is set to
minimum.
Defective disc.
Erratic playback.
Dirty or defective
disc.
Time display blinks. Clock not set.
AM or FM, no sound. Power is not on.
Volume is set to
minimum.
SOLUTION
Check AC cord
connection.
Close CD compartment
door.
Reinsert disc correctly.
Try another disc.
Wipe disc with soft cloth.
Increase volume.
Try another disc.
Clean or replace disc.
Set the clock.
Press the POWER
button to turn the unit on.
Increase volume.
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE VISIT
OUR WEBSITE AT
WWW.MEMCORPINC.COM
OR CONTACT CUSTOMER SERVICE AT 1-800-919-3647.
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN
CASE YOU NEED TO RETURN THIS PRODUCT TO YOUR PLACE OF
PURCHASE OR MEMOREX.
FOR PARTS AND ACCESSORIES, CONTACT FOX INT’L AT 1-800-321-6993.
19
MMG-CR3810.OM.QXD
7/15/02
7:09 AM
Page 20
Memcorp, Inc.
Weston, Fl
Printed in Hong Kong
Visit our website at www.memcorpinc.com