Craftsman 172.10721 Owner`s manual

Owner's Manual
®
7-in.
Buffer / Polisher
Model No.
172.10721
CAUTION: Read, understand and follow
all Safety Rules and Operating Instructions
in this manual before using this product.
Sears, Roebuck and Co.,
Hoffman Estates, IL 60179 U.S.A.
Visit our Craftsman® website:
www.sears.com /craftsman
• WARRANTY
• SAFETY
• UNPACKING
• DESCRIPTION
• OPERATION
• MAINTENANCE
• ACCESSORIES
TABLE OF CONTENTS
SAFETY SYMBOLS
Warranty.........................................................................Page
Safety Symbols...............………….................................Page
Safety Instructions...............…………............................Pages
Unpacking......................................................................Page
Description.....................................................................Page
Operation...................…………………...........................Pages
Maintenance.................................................................. Page
Accessories..................................................................Page
2
3
4-8
9
10
11-15
15
16
The purpose of safety symbols is to attract your attention to possible dangers.
The safety symbols, and the explanations with them, deserve your careful
attention and understanding. The symbol warnings DO NOT by themselves
eliminate any danger. The instructions and warnings they give are no substitutes
for proper accident prevention measures.
! WARNING: BE SURE to read and understand all safety instructions in
this manual, including all safety alert symbols such as “DANGER”, “WARNING”
and “CAUTION”, BEFORE using this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or serious personal injury.
SYMBOL MEANING
!
ONE YEAR FULL WARRANTY ON CRAFTSMAN® TOOL
If this Craftsman tool fails due to a defect in material or workmanship
within one year from the date of purchase, RETURN IT TO THE NEAREST
SEARS STORE OR OTHER CRAFTSMAN OUTLET IN THE UNITED
STATES FOR FREE REPLACEMENT.
This warranty does not include expendable parts such as lamps, batteries,
bits or blades or bonnets.
If this Craftsman product is used for commercial or rental purposes, this
warranty applies for only 90 days from the date of purchase.
This warranty gives you specific legal rights, and you may also have other
rights, which vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
SAVE THESE INSTRUCTIONS!
READ ALL INSTRUCTIONS!
! WARNING: Some dust created by using power tools contains
chemicals known to the State of California to cause cancer and birth defects
or other reproductive harm.
2
SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, OR
CAUTION. May be used in conjunction with other symbols or pictographs.
!
DANGER
!
WARNING
!
CAUTION
Failure to obey this safety warning WILL result in death or
serious injury to yourself or to others. Always follow the
safety precautions to reduce the risk of fire, electric shock
and personal injury.
Failure to obey this safety warning CAN result in death or
serious injury to yourself or to others. Always follow the
safety precautions to reduce the risk of fire, electric shock
and personal injury.
Failure to obey this safety warning MAY result in personal
injury to yourself or others or property damage. Always
follow the safety precautions to reduce the risk of fire,
electric shock and personal injury.
DAMAGE PREVENTION AND INFORMATION MESSAGES
These inform user of important information and /or instructions that could lead to
equipment or other property damage if not followed. Each message is preceded by the
word “NOTE:” as in the example below:
NOTE: Equipment and/or property damage may result if these instructions
are not followed.
! WARNING: The operation of any power tool can
result in foreign objects being thrown into your eyes,
which can result in severe eye damage. Before beginning
power tool operation, ALWAYS wear safety goggles or
safety glasses with side shield and a full-face shield
when needed. We recommend a Wide Vision Safety
Mask for use over eyeglasses or standard safety glasses
with side shield, available at Sears Stores or other
Craftsman Outlets.
3
SAFETY INSTRUCTIONS
!
SAFETY INSTRUCTIONS cont.
WARNING: BE SURE to read and understand all instructions in this
manual before using this power tool. Failure to follow all instructions may result in
electric shock, fire and / or serious personal injury.
WORK AREA SAFETY
TOOL USE AND CARE SAFETY
! WARNING: BE SURE to read and understand all instructions before
operating this tool. Failure to follow all instructions listed below may result
in electric shock, fire and/or serious personal injury.
1. Keep your work area clean and well lit. Cluttered and dark areas invite accidents.
1. DO NOT use the tool if switch does not turn it “On” or “Off”. Any tool that
cannot be controlled with the switch is dangerous and must be repaired.
2. DO NOT operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases, or dust. Power tools create sparks which may ignite the
dust or fumes.
2. DISCONNECT the plug from the power source before making any
adjustments, changing accessories or storing the tool. Such preventive
safety measures reduce the risk of starting the tool accidentally.
3. Keep bystanders, children and visitors away while operating a power tool.
Distractions can cause you to lose control.
3. STORE idle tools out of the reach of children and other untrained persons.
Tools are dangerous in the hands of untrained users.
4. MAKE SURE the work area has ample lighting so you can see the work and that
there are no obstructions that will interfere with safe operation BEFORE using your
buffer / polisher.
4. CHECK for misalignment or binding of moving parts, breakage of parts, and
any other condition that may affect the tool’s operation. If damaged, have the
tool serviced before using. Many accidents are caused by poorly maintained tools.
5. USE ONLY accessories that are recommended for this tool. Accessories that
may be suitable for one tool may become hazardous when used on another tool.
PERSONAL SAFETY
1. KNOW your power tool. Read the operator’s manual carefully. Learn the tool’s
applications and limitations, as well as the specific potential hazards related to
this tool.
2. STAY ALERT, watch what you are doing and use common sense when operating a
power tool.
3. DO NOT use tool while tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in serious personal
injury.
4. DRESS properly. DO NOT wear loose clothing or jewelry. Pull back long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose clothing, or long
hair can be caught in moving parts. Air vents often cover moving parts and should also
be avoided.
5. AVOID accidental starting. Be sure switch is in “OFF” position before plugging in.
DO NOT carry tools with your finger on the switch. Carrying tools with your finger on
the switch or plugging in tools that have the switch in the “ON” position invites
accidents.
6. Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control of the tool in unexpected situations.
7. USE SAFETY EQUIPMENT. Always wear eye protection.
4
ELECTRICAL SAFETY
1. Double insulated tools are equipped
with a polarized plug (one blade is wider
than the other). This plug will fit in a
polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified
electrician to install a polarized outlet. Do
not change the plug in any way.
2. Double insulation eliminates the need
for the three-wire grounded power cord and
grounded power supply system. Applicable
only to Class II (double-insulated) tools.
This tool is a double insulated tool.
3. BEFORE plugging in the tool, BE SURE that
the outlet voltage supplied is within the
voltage marked on the tool’s data plate.
DO NOT use “AC only” rated tools with a
DC power supply.
5
Cover of
Grounded
Outlet Box
SAFETY INSTRUCTIONS cont.
SAFETY INSTRUCTIONS cont.
ELECTRICAL SAFETY cont.
SAFETY SYMBOLS FOR YOUR TOOL
4. AVOID body contact with grounded surfaces, such as pipes, radiators, ranges
and refrigerators. There is an increased risk of electric shock if your body is
grounded.
The label on your tool may include the following symbols.
5. DO NOT expose power tools to rain or wet conditions or use power tools in
wet or damp locations. Water entering a power tool will increase the risk of
electric shock.
6. INSPECT tool cords for damage. Have damaged tool cords repaired at a Sears
Service Center. BE SURE to stay constantly aware of the cord location and keep
it well away from the moving blade.
7. DO NOT abuse the cord. NEVER use the cord to carry the tool by or to pull
the plug from the outlet. Keep cord away from heat, oil, sharp edges or moving
parts. Replace damaged cords immediately. Damaged cords increase the risk of
electric shock.
V.......................................................................Volts
A...................................................................... Amps
Hz.................................................................... Hertz
W..................................................................... Watts
min..................................................................Minutes
....................................................................Alternating current
..................................................................Direct current
no ....................................................................No-load speed
....................................................................Class II construction, Double Insulated
RPM………………………............................. . .Revolutions per minute
SPM…...........................…………………….....Strokes per minute
OPM………………..........................………..... Orbits per minute
! ....................................................................Indicates danger, warning or caution.
It means attention! Your safety is involved.
SERVICE SAFETY
EXTENSION CORDS
Use a proper extension cord. ONLY use cords listed by Underwriters Laboratories
(UL). Other extension cords can cause a drop in line voltage, resulting in a loss of
power and overheating of tool. For this tool an AWG (American Wire Gauge) size of a
least 14-gauge is recommended for an extension cord of 25 - ft. or less in length. Use
12 - gauge for an extension cord of 50 - ft. Extension cords 100-ft. or longer are not
recommended. Remember, a smaller wire gauge size has greater capacity than
a larger number (14 - gauge wire has more capacity than 16-gauge wire; 12-gauge
wire has more capacity than 14 - gauge). When in doubt use the smaller number.
When operating a power tool outdoors, use an outdoor extension cord marked
“W-A” or “W”. These cords are rated for outdoor use and reduce the risk of electric
shock.
! CAUTION: Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on lumber, tools, parts of the
vehicle or other obstructions while you are working with a power tool.
! WARNING: Check extension cords before each use. If damaged
replace immediately. Never use tool with a damaged cord since touching
the damaged area could cause electrical shock, resulting in serious injury.
6
1. If any part of this tool is missing or should break, bend, or fail in any way;
or should any electrical component fail to perform properly: SHUT OFF the
power switch and remove the tool’s plug from the power source and have the
missing, damaged or failed parts replaced BEFORE resuming operation.
2. Tool service must be performed only at a Sears Service Center. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
3. When servicing a tool, use only identical replacement parts. Follow
instructions in the maintenance section of this manual. Use of unauthorized
parts or failure to follow maintenance instructions may create a risk of
electric shock or injury.
SAFETY RULES FOR BUFFER / POLISHERS
! WARNING: USE OF ACCESSORIES THAT ARE NOT RECOMMENDED
FOR USE WITH THIS TOOL MAY CREATE A HAZARDOUS CONDITION.
1. Read, understand and follow all safety rules and user instructions in this manual
and all directions and warnings on polishes and waxes BEFORE using this
buffer / polisher.
2. Vehicle should be clean and dry before using your buffer polisher. Remove all road
tar, excess grease spots and bug stains.
3. ALWAYS make sure the vehicle’s surface is cool before washing and using the
buffer / polisher.
4. When changing accessories, BE SURE that the switch is in the OFF position and
the cord is unplugged.
5. DO NOT apply wax directly on car.
7
SAFETY INSTRUCTIONS cont.
SAFETY RULES FOR BUFFER / POLISHERS cont.
6. To avoid splashing wax, ALWAYS start and stop the buffer / polisher on or against
the surface to be polished.
7. After plugging in extension cord, loop extension cord over tool’s stub length plug.
Then wrap hook and loop strip around extension cord to secure it in place.
8. Place extension cord over your shoulder to keep it safely out of your way.
9. DO NOT apply excessive pressure against the work surface with this tool. The
random orbital motion feature on this tool will perform better when less pressure
is applied. Applying excessive pressure will slow the random orbital motion and
reduce the effectiveness of the tool.
10. To prolong the life of the pad on the buffer / polisher, ALWAYS store the
buffer / polisher with the pad face up.
11. DO NOT USE ABRASIVE COMPOUNDS WITH THIS TOOL.
12. DO NOT immerse any part of the buffer / polisher in liquid.
! WARNING: Some dust created by using power tools contains
chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonryproducts.
• Arsenic and chromium, from chemically treated lumber.
SAFETY INSTRUCTIONS cont.
ADDITIONAL RULES FOR SAFE OPERATION
! WARNING: BE SURE to read and understand all instructions.
Failure to follow all instructions listed below may result in electric shock,
fire and /or serious personal injury.
1. Know your power tool. Read operator’s manual carefully. Learn the applications
and limitations, as well as the specific potential hazards related to this tool. Following
this rule will reduce the risk of electric shock, fire or serious injury.
2. ALWAYS wear eye protection when using this tool.
3. PROTECT your lungs. Wear a face mask or dust mask if the operation is dusty.
4. INSPECT the tool cords periodically and if damaged have them repaired
at your nearest Sears Service Center. ALWAYS BE AWARE of the cord location
when operating your tool.
5. ALWAYS check the tool for damaged parts. Before further use of the tool,
a guard or other part that is damaged should be carefully checked to determine if
it will operate properly and perform its intended function. Check for misalignment
or binding of moving parts, breakage of parts, and any other condition that may
affect the tool’s operation. A guard or other part that is damaged should be
properly repaired or replaced at a Sears Service center.
6. SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to
instruct others who may use this tool. If someone borrows this tool, make
sure they have these instructions also.
Your risk from these exposures varies, depending upon how often you do
this type of work. To reduce your exposure to these chemicals:
• Work in a well-ventilated area.
• Work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
Avoid prolonged contact with dust from power sanding, sawing, grinding,
drilling and other construction activities. Wear protective clothing and wash
exposed areas with soap and water. Allowing dust to get into your mouth,
eyes, or lay on the skin may promote absorption of harmful chemicals.
! WARNING: Use of this tool can generate and/or disburse dust, which
may cause serious and permanent respiratory or other injury. Always use
NIOSH/OSHA approved respiratory protection appropriate for the dust
exposure. Direct particles away from face and body.
8
9
DESCRIPTION
UNPACKING
!
WARNING: Your tool should NEVER be connected to the power
source when you are assembling parts, making adjustments, installing or
removing bonnets, cleaning or when it is not in use. Disconnecting the tool
will prevent accidental starting, which could cause serious personal injury.
1. Remove the buffer / polisher from the carton and inspect it carefully to make sure
that no breakage or damage has occurred during shipping.
2. Do not discard any of the packing materials until all parts are accounted for.
3. Two bonnets are included: wax applicator bonnet for applying waxes, and a
reusable terry cloth bonnet for removing waxes and polishing.
4. If any of the parts are damaged or missing (refer to PARTS LIST below), return the
buffer / polisher to your nearest Sears store or Craftsman outlet to have the tool
replaced.
!
WARNING: If any parts are missing, DO NOT operate this
buffer / polisher until the missing parts are replaced. Failure to do so could
result in possible serious personal injury.
PARTS LIST (Fig. 1)
KNOW YOUR BUFFER / POLISHER
NOTE: Before attempting to use your buffer / polisher, familiarize yourself
with all of the operating features and safety requirements.
Your Craftsman buffer / polisher has a precision-built electric motor and it should be
connected to a 120-volt, 60-Hz AC ONLY power supply (normal household current).
DO NOT operate on direct current (DC). The large voltage drop will cause a loss of
power and the motor will overheat. If the tool does not operate when plugged into
correct 120-volt, 60-Hz AC ONLY outlet, check the power supply. This buffer / polisher
has a stub length, 2-wire power cord (no adapter needed).
This Craftsman Buffer / Polisher has the following features:
1. Powerful 1.0 Amp permanent magnet Motor with 3800 Orbits per Minute
provides the power needed for quality waxing, buffing and polishing.
2. Precision tuned Counterweight system reduces vibration for smooth,
comfortable operation with less operator fatigue
3. Precision tuned Counterweight System matched with Orbital Motion provides
a “swirl-free” shine.
4. Ergonomically designed Perimeter Handle System provides maximum balance,
control and gripping comfort on any horizontal or vertical surface.
5. Hook and Loop Strip helps keep extension cord securely plugged into
buffer / polisher.
6. On / Off Slide Switch conveniently located for ease in control.
7. 7-in. diameter Foam Pad follows surface contours for efficient buffing / polishing.
Chemical resistant for long life.
Buffer / Polisher
8. One Wax Applicator Bonnet for applying wax.
9. One Reusable Terry Cloth Bonnet for removing wax and polishing.
10. Non-marring Flat Top of buffer / polisher provides a stable base when applying
wax to bonnets and changing bonnets.
11. Permanently lubricated Ball Bearings for smooth, efficient operation.
12. Lightweight, High-impact Resistant Housing reduces weight, helps protect
tool from damage.
Wax
Applicator
Bonnet
Reusable Terry
Cloth Bonnet
Operator’s Manual
10
11
OPERATION cont.
DESCRIPTION cont.
KNOW YOUR BUFFER / POLISHER cont.
Perimeter
Handle System
Non-marring Flat Top Cap
On/Off
Slide Switch
Fig. 2
BEFORE YOU BEGIN TO WAX, BUFF AND POLISH YOUR CAR:
1. Remove all road tar, excess grease spots and bug stains with a general-purpose
cleaner.
2. Wash, clean and dry your vehicle.
3. Make sure the work area is dry.
ATTACHING THE WAX APPLICATOR BONNET TO THE FOAM PAD
(See Figure 3)
Stub Lengh
Cord
Hook and
Loop Strip
Foam Pad Base
PRODUCT SPECIFICATIONS
Pad Diameter
7-in.
Motor OPM
3800
Rating
120 volts, 60 Hz AC
Amps
1.0
OPERATION
Before attempting to use your tool, familiarize yourself with all of the operating
features and safety requirements.
! WARNING: IF ANY PARTS ARE MISSING, DO NOT OPERATE THIS
BUFFER / POLISHER UNTIL THE MISSING PARTS ARE REPLACED.
FAILURE TO DO SO COULD RESULT IN POSSIBLE SERIOUS PERSONAL
INJURY.
!
1. Place wax applicator bonnet on foam pad
as shown in Fig. 3.
2. ALWAYS make sure that the elastic strip
on the bottom of the bonnet is securely
tucked on the underside of the foam pad.
APPLYING WAX TO BONNET (See Figures 4 and 5)
IMPORTANT: DO NOT APPLY WAX DIRECTLY
Fig. 4
ON CAR!
Applying Paste Wax to Bonnet (See Figure 4)
1. Spread a heaping teaspoon of wax evenly over
entire surface of applicator bonnet using a
putty knife or any other flat object (See Fig. 4).
Applying Liquid Wax to Bonnet (See Figure 5)
1. Apply three swirls of wax over applicator
bonnet (See Fig. 5).
2. This should be enough to cover 1/4 of car
surface.
3. For the second and third and fourth applications,
only use about one half as much as on first
application. The bonnet will not absorb as
much wax on these applications.
CAUTION: ALWAYS wear eye protection while operating this power
tool.
12
Fig. 3
! WARNING: When changing
accessories, BE SURE that the switch is
in the OFF position and the cord is
unplugged.
13
Fig. 5
OPERATION cont.
OPERATION cont.
RUNNING YOUR BUFFER / POLISHER AND WAXING VEHICLE
1. After plugging tool into extension cord, loop
Fig. 6
extension cord over tool’s stub length plug.
Then wrap hook and loop strip around
extension cord to secure it in place.
2. To avoid splashing wax, ALWAYS start and
stop the buffer / polisher against the surface
to be polished.
3. Place the extension cord over your shoulder
to keep it safely out of your way (see Fig. 6).
4. Place buffer / polisher against vehicle and
turn buffer / polisher ON by sliding switch
to On position.
5. Apply wax in a straight line with either a
side-to-side or back and forth motion.
ALWAYS use broad, even strokes when
applying wax (See Fig. 7).
Fig. 7
6. Start applying wax to the flat surfaces (hood,
trunk and roof) first. Wax one section at a
time (see Fig. 8).
7. After flat surfaces are covered with wax,
do the sides. The perimeter handle system
allows easy polishing of horizontal and
vertical surfaces. Hold tool with the cord
hanging free (see Fig. 9).
Fig. 8
8. Apply wax in a thin, even coat. Too much wax
1
does not add any more protection and only
makes the wax removal more difficult.
LEFT
9. The random orbit motion of the buffer /
polisher provides was application that cannot
2
be duplicated, not even “by hand”.
IMPORTANT: DO NOT apply excessive
pressure against the work surface with this tool.
The random orbital motion feature on this tool
will perform better when less pressure is
applied. Applying excessive pressure will slow
the random orbital motion and reduce the
effectiveness of the tool.
10. It is easiest to apply the wax to the entire
surface before starting the removal phase;
however, follow the specific
recommendations of the wax or polish
being used.
14
RUNNING YOUR BUFFER / POLISHER AND WAXING VEHICLE cont.
11. When you have finished applying wax with
Fig. 10
the applicator, bonnet, SHUT OFF the
buffer / polisher before removing from the
car’s surface.
12. Remove the wax applicator bonnet and use
it to hand polish all the hard-to-reach
surfaces (under bumpers, around door
handles, etc.) (see Fig. 10).
13. Properly dispose of wax applicator bonnet.
ATTACHING THE POLISHING BONNET TO THE FOAM PAD (Fig. 11)
! WARNING: When changing
accessories, BE SURE that the switch is
in the OFF position and the cord is
unplugged.
Fig. 11
1. Place the terry bonnet on foam pad as
shown in Fig. 11.
2. ALWAYS make sure that the elastic strip
on the bottom of the bonnet is securely
tucked on the underside of the foam pad.
3
RIGHT
4
Fig. 9
BUFFING AND POLISHING - REMOVING THE WAX FROM THE SURFACE
(See Fig. 12)
Fig. 12
NOTE: Remove wax in the same order in which
it was applied.
1. Wait until wax has dried to an even haze
on vehicle.
2. Place extension cord over your shoulder.
3. Turn buffer / polisher ON.
IMPORTANT: DO NOT apply excessive
pressure against the work surface with this tool.
The random orbital motion feature on this tool
will perform better when less pressure is applied. Appling excessive pressure will
slow the random orbital motion and reduce the effectiveness of the tool.
NOTE: For best results, use long, sweeping strokes in a criss-cross pattern when
removing wax.
4. Buff and polish the entire surface until all dried wax is removed. Remove the
bonnet from time to time and shake out the dried wax residue. A bonnet with
excess residue will cause streaking. You may need to replace the bonnet with a
new one if you can’t get it clean enough to avoid streaking.
5. Use a clean terry cloth bonnet for final buffing and polishing. Or use a foam
polishing bonnet (sold separately) for the ultimate “showroom” shine.
15
OPERATION cont.
ACCESSORIES
CAR CARE TIPS
1. Wash and polish the car 3 to 4 times a year to help ensure paint protection.
2. Wash the car at least every 2 weeks with a car wash solution which will not harm
the finish or strip the wax. AVOID washing with household detergents.
3. Wash with a clean sponge and dry with a terry cloth towel to help prevent dirt from
scratching the paint. Start on the top and work down.
4. Remove bugs, bird droppings, tree sap and tar from the car’s surface on a daily
basis.
5. ALWAYS make sure that the car’s surface is cool before washing.
6. Avoid parking near sprinklers, because water spots are difficult to remove.
7. ALWAYS keep glass cleaner chemicals away from painted surfaces. Spray the
cleaner onto a towel, NOT directly on the windows.
! WARNING: The use of attachments or accessories that are not
recommended for this tool might be dangerous and could result in serious
injury.
Sears and other Craftsman® outlets offer a large selection of Craftsman
buffer / polisher accessories designed for all your buffing and polishing
applications.
Look for these Craftsman accessories. They are specially designed to make
your 7-in. Buffer / Polisher more efficient to use.
Wax Applicator Bonnets for applying waxes and polishes.
Terry Cloth Bonnets use for removing wax and for buffing and polishing.
MAINTENANCE
Polishing Bonnets for final buffing and polishing to a “showroom” shine.
1. Terry cloth bonnets can be machine washed in cold water, using a small amount
of detergent. Machine dry at medium temperature. HOWEVER, we recommend
hand washing and air drying for longer bonnet life.
2. Wax applicator bonnets should only be used once, then disposed of properly.
3. Remove the bonnet from the foam pad when the buffer / polisher is not is use,
so the pad can dry out and retain its original shape.
4. To prolong the life of the foam pad, ALWAYS store the buffer / polisher with the
pad face up.
5. NEVER USE ABRASIVE COMPOUNDS WITH THIS TOOL.
6. DO NOT apply too much wax to the bonnet. Applying too much wax causes the
bonnet to become saturated and it will not last as long. THIS MAKES
POLISHING MORE DIFFICULT AND IT TAKES LONGER.
7. If the bonnet is continually coming off the pad, you may be using too much wax.
8. If buffing seems difficult, you have used too much wax.
9. ONLY USE a mild soap solution and a damp sponge to clean the buffer / polisher.
10. DO NOT immerse ay part of the buffer / polisher in liquid.
16
Quality Waxes for the finest protection and appearance.
Visit your local Sears store or other Craftsman outlets or shop
sears.com/craftsman for all of the accessories for your buffer / polisher.