Qlogic QLogic 12000 Series Installation guide

QLogic 12000 Series
InfiniBand Switches and Directors
Hardware Installation Guide
Version 6.0
D000140-001 D
QLogic 12000 Series InfiniBand Switches and Directors
Hardware Installation Guide
Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no
responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its
use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications
described in this document for any of these products are for illustrative purposes only. QLogic Corporation makes no
representation nor warranty that such applications are suitable for the specified use without further testing or
modification. QLogic Corporation assumes no responsibility for any errors that may appear in this document.
Document Revision History
Revision D, August 10, 2010
Changes
Sections Affected
Added procedures for the 12800-Series management module protective label.
“12800-Series Management Module Protective
Label Guidelines” on page 1-49
Added information for the 12800-series DC
ON/OFF switch.
“Connecting Power” on page 1-47
Added a note in Appendix A: 12800 management
modules should be replaced one at a time.
“Management Module Replacement” on
page D-10
Page ii
D000140-001 D
Table of Contents
Preface
Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
License Agreements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1-1
1-1
1-2
1-2
1-2
Installation
Planning the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable Distances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable Handling and Bend Radius . . . . . . . . . . . . . . . . . . . . . . .
Uninterruptible Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Tasks Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools and Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Check the Installation Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mark the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12200/12300 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Four Post Standard-Depth Rack Installation . . . . . . . . . . . . . . . . . . . .
Mounting Hardware Kit Contents:. . . . . . . . . . . . . . . . . . . . . . . .
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12200 Four Post Shallow-Depth Rack Installation . . . . . . . . . . . . . . .
Mounting Hardware Kit Contents:. . . . . . . . . . . . . . . . . . . . . . . .
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12800-040 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting Hardware Kit Contents: . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12800-120 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting Hardware Kit Contents: . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12800-180 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting Hardware Kit Contents: . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D000140-001 D
1-1
1-2
1-2
1-2
1-3
1-4
1-5
1-5
1-5
1-6
1-7
1-7
1-7
1-7
1-9
1-9
1-10
1-12
1-12
1-13
1-16
1-16
1-17
1-24
1-24
iii
QLogic 12000 Series InfiniBand Switches and Directors
Hardware Installation Guide
Selecting a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12800-360 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting Hardware Kit Contents: . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Locating Rack Mounting Posts for Front and Back Cable Routing
Installation Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connect Equipment to the Ports and Power On the System . . . . . . . . . . . .
Connecting Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bringing Up the System For the First Time . . . . . . . . . . . . . . . . . . . . . . . . .
12800-Series Management Module Protective Label Guidelines . . . .
Staging Area Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Site Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Start-up Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the Switch IP Address and Default Gateway via the CLI . .
Updating the Management Module IP Addresses in a Redundant
Management Configuration (12800-040, 12800-120, 12800-180 and
12800-360) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enabling 8X Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Creating an 8x Port: 12200/12300 . . . . . . . . . . . . . . . . . . . . . . .
Creating an 8x Port: 12800 Series . . . . . . . . . . . . . . . . . . . . . . .
Component LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Module Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Module Attention. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chassis Status and Attention . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fault Tolerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Master. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MRL Active . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Leaf Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IB Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Module Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Module Attention. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spine Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Module Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Module Attention. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SEEB Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RJ45 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MRL Active . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iv
1-24
1-24
1-33
1-33
1-33
1-35
1-36
1-47
1-48
1-50
1-50
1-50
1-51
1-52
1-53
1-55
1-56
1-57
1-59
1-62
1-62
1-62
1-62
1-63
1-63
1-63
1-63
1-64
1-65
1-65
1-65
1-65
1-66
1-66
1-66
1-67
1-67
1-67
D000140-001 D
QLogic 12000 Series InfiniBand Switches and Directors
Hardware Installation Guide
12200 and 12300. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IB Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RJ45 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12800 Fans and Power Supplies. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fan LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switch-Based QLogic Fabric Manager License Key . . . . . . . . . . . . . . . . . .
Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
QLogic 12000 Six-Port Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A
QLogic 12000 Series Product Specifications
Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12200 and 12300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cooling and Thermal Management: . . . . . . . . . . . . . . . . . . . . . . . . . .
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12800 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Distribution Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B
1-68
1-68
1-68
1-68
1-69
1-69
1-69
1-70
1-71
1-72
1-79
1-80
A-1
A-2
A-2
A-2
A-2
A-3
A-4
A-6
Safety and Regulatory Compliance Information
Safety Information
Statement 1:
Statement 2:
Statement 3:
Statement 4:
Statement 5:
Statement 6:
Statement 7:
............................................
............................................
............................................
............................................
............................................
............................................
............................................
............................................
C
Serial Port Pinouts
D
FRU Replacement
QLogic 12200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chassis Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D000140-001 D
B-1
B-1
B-3
B-6
B-8
B-10
B-12
B-14
D-1
D-1
D-1
D-1
v
QLogic 12000 Series InfiniBand Switches and Directors
Hardware Installation Guide
QLogic 12300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chassis Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fan/Power Supply Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
QLogic 12800 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fan Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Leaf Module Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spine Module Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management Module Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
vi
D-2
D-2
D-2
D-2
D-2
D-3
D-3
D-4
D-4
D-4
D-5
D-6
D-6
D-6
D-7
D-7
D-8
D-9
D-9
D-9
D-10
D-10
D-10
D000140-001 D
Preface
This manual describes the hardware installation and initial configuration tasks for
the QLogic 12000 series that includes:
„
The QLogic 12200 36-port fixed-configuration InfiniBand switch
„
The QLogic 12300 36-port configurable InfiniBand switch
„
The QLogic 12300 18-port configurable InfiniBand switch
„
The QLogic 12800 series:
‰
12800-040
‰
12800-120
‰
12800-180
‰
12800-360
This manual is organized as follows:
Preface describes the intended audience and technical support.
Section 1 describes the hardware installation and initial configuration tasks.
Appendix A provides product specification information.
Appendix B provides product safety and regulatory information.
Appendix C provides serial port pinout information.
Appendix D provides FRU replacement information.
Intended Audience
This manual is intended to provide network administrators and other qualified
personnel a reference for hardware installation and initial configuration for the
switches.
Documentation Conventions
This guide uses the following documentation conventions:
„
D000140-001 D
NOTE: provides additional information.
vii
Preface
Documentation Conventions
„
CAUTION! indicates the presence of a hazard that has the potential of
causing damage to data or equipment.
„
WARNING!! indicates the presence of a hazard that has the potential of
causing personal injury.
„
Text in blue font indicates a hyperlink (jump) to a figure, table, or section in
this guide, and links to Web sites are shown in underlined blue. For
example:
„
„
„
„
„
viii
‰
Table 9-2 lists problems related to the user interface and remote agent.
‰
See “Installation Checklist” on page 3-6.
‰
For more information, visit www.qlogic.com.
Text in bold font indicates user interface elements such as a menu items,
buttons, check boxes, or column headings. For example:
‰
Click the Start button, point to Programs, point to Accessories, and
then click Command Prompt.
‰
Under Notification Options, select the Warning Alarms check box.
Text in Courier font indicates a file name, directory path, or command line
text. For example:
‰
To return to the root directory from anywhere in the file structure:
Type cd /root and press ENTER.
‰
Enter the following command: sh ./install.bin
Key names and key strokes are indicated with UPPERCASE:
‰
Press CTRL+P.
‰
Press the UP ARROW key.
Text in italics indicates terms, emphasis, variables, or document titles. For
example:
‰
For a complete listing of license agreements, refer to the QLogic
Software End User License Agreement.
‰
What are shortcut keys?
‰
To enter the date type mm/dd/yyyy (where mm is the month, dd is the
day, and yyyy is the year).
Topic titles between quotation marks identify related topics either within this
manual or in the online help, which is also referred to as the help system
throughout this document.
D000140-001 D
Preface
License Agreements
License Agreements
Refer to the QLogic Software End User License Agreement for a complete listing
of all license agreements affecting this product.
Technical Support
Customers should contact their authorized maintenance provider for technical
support of their QLogic products. QLogic-direct customers may contact QLogic
Technical Support; others will be redirected to their authorized maintenance
provider.
Visit the QLogic support Web site listed in Contact Information for the latest
firmware and software updates.
Availability
QLogic Technical Support for products under warranty is available during local
standard working hours excluding QLogic Observed Holidays.
Training
QLogic offers training for technical professionals for all iSCSI, InfiniBand, and
Fibre Channel products. From the main QLogic web page at www.qlogic.com,
click the Education and Resources tab at the top, then click the Education &
Training tab on the left. The QLogic Global Training Portal offers online courses,
certification exams, and scheduling of in-person training.
Technical Certification courses include installation, maintenance and
troubleshooting QLogic products. Upon demonstrating knowledge using live
equipment, QLogic awards a certificate identifying the student as a Certified
Professional. The training professionals at QLogic may be reached by e-mail at
training@qlogic.com.
Contact Information
Please feel free to contact your QLogic approved reseller or QLogic Technical
Support at any phase of integration for assistance. QLogic Technical Support can
be reached by the following methods:
D000140-001 D
Web
http://support.qlogic.com
Email
support@qlogic.com
ix
Preface
Technical Support
Knowledge Database
The QLogic knowledge database is an extensive collection of QLogic product
information that you can search for specific solutions. We are constantly adding to
the collection of information in our database to provide answers to your most
urgent questions. Access the database from the QLogic Support Center:
http://support.qlogic.com.
x
D000140-001 D
1
Installation
This section describes how to install and configure for first-time use:
„
The QLogic 12000 switches in a network environment.
Planning the Installation
The 12000 is designed to be installed in an existing 19-inch equipment rack or
server rack.
NOTE:
These switches are designed for a four-post server cabinet. Do not mount in
a two-post telco cabinet.
Racks should conform to conventional standards. Use the American National
Standards Institute (ANSI)/Electronic Industries Association (EIA) standard
ANSI/EIA-310-D-92 and International Electrotechnical Commission (IEC) 297
Racks should meet the following mechanical recommendations:
„
Four-post, 19" rack to facilitate easy maintenance
„
Universal mounting rail hole pattern identified in IEC Standard 297
„
Mounting holes flush with the rails to accommodate the chassis
NOTE:
Operation is subject to the following conditions:
Use a rack grounding kit and a ground conductor that is carried back to earth
or to another suitable building ground. Ground the equipment rack to earth
ground.
Provide enough room to work on the equipment. Clear the work site of any
unnecessary materials. Make sure the equipment will have enough
clearance for front and rear access.
D000140-001 D
1-1
1–Installation
Planning the Installation
Cable Requirements
Cable Distances
When planning the location of the switches, consider the distance limitations for
signaling, EMI, and connector compatibility. It is recommended that the user does
not exceed specified transmission rate and distance limits.
Cable Guidelines
NOTE:
Building and electrical codes vary depending on the location. Comply with all
code specifications when planning the site and installing cable.
When running cable to the equipment, consider the following:
1-2
„
Do not run cables where they can be stepped on or rolled over.
„
Be sure cables are intact with no cuts, bends, or nicks.
„
If the user is making a cable, ensure that the cable is properly crimped.
„
Provide proper strain relief for IB cables.
„
Support cables using a cable manager mounted above connectors to avoid
unnecessary weight on the cable bundles.
„
Bundle cable using velcro straps to avoid injuring cables.
„
Keep all ports and connectors free of dust.
„
Untwisted Pair (UTP) cables can build up Electrostatic Discharge (ESD)
charges when being placed into a new installation. Before installing category
5 UTP cables, discharge ESD from the cable by plugging it into a port on a
system that is not powered on.
„
When required for safety and fire rating requirements, plenum-rated cable
can be used. Check the local building codes to determine when it is
appropriate to use plenum-rated cable, or refer to IEC standard 850.
D000140-001 D
1–Installation
Planning the Installation
Cable Handling and Bend Radius
Provide proper strain relief by adhering to the following guidelines:
Table 1-1. IB Copper Cable Guidelines
IB Copper Cable Bend Radii
American Wire Gauge (AWG)
Size Cable
Bend Radius
26
2.43 inches
28
2.28 inches
30
1.98 inches
For copper cable, the temporary 90-degree bend can never be more than 0.5
inches tighter than the values listed above for any assembly. This is the absolute
minimum sustained bend radius for each cable AWG size. This measurement is
the distance from the switch panel to the point where the cable makes a
90-degree bend. In other words, this number includes the distance from the
connector stand-off from the panel surface.
Figure 1-1. Copper Cable Bend Radius
D000140-001 D
1-3
1–Installation
Planning the Installation
Table 1-2. IB Fiber Optic Cable Guidelines
IB Fiber Optic Cable Bend Radii
Cable Type
Fiber Optic Standard Cable
Bend Radius
25 millimeters
NOTE: A 50mm diameter is the smallest circle limit
Figure 1-2. Fiber Optic Bend Radius
Uninterruptible Power Supply
Consider the following when selecting Uninterruptible Power Supply (UPS)
equipment:
„
1-4
The minimum amperage requirements for a UPS:
‰
Calculate VA (Volt-Amps): Locate the voltage and amperage
requirements for each piece of equipment (usually located on a sticker
on the back or bottom of the equipment). Multiply the numbers
together to get VA.
‰
Add the VA from each piece of equipment together to find the total VA
requirement. Then add 30% to determine the minimum amperage
requirements for the UPS.
„
Transition time (the time necessary for the UPS to transfer from utility power
to full-load battery power).
„
The longest potential time period the UPS might be required to supply
backup power.
D000140-001 D
1–Installation
Installation Tasks Checklist
„
Whether or not the UPS unit also provides online protection.
Installation Tasks Checklist
To perform the actual switch installation, the site implementation engineer must
perform the following tasks, which are detailed in this section.
CAUTION!
Be sure to review the safety information before starting the installation and during the
installation process (refer to Appendix B.
1.
Check the installation site to verify the installation of cabinet power feeds,
rails, and grounding.
2.
Unpack the equipment and inspect for any shipping damage. Any shipping
damage should be reported to the shipping company.
3.
Verify that the equipment shipped matches the packing list.
4.
Mark the rack and install the mounting rails.
5.
Physically install the switch in the rack.
Tools and Equipment Required
„
An ESD wrist strap
„
A #2 Phillips screwdriver
„
An M6 HEX nut wrench
„
Pen (felt-tip) to mark the mounting holes
„
Lifting device (e.g., pallet jack) for the 12800-360 and 12800-180
Check the Installation Site
The switches are designed to be installed in an existing server cabinet (not a telco
cabinet), where it can be mounted in a standard equipment rack.
Be sure of the following:
„
The cabinet has a full earth ground to provide reliable grounding.
„
There is enough room to work on the equipment.
„
The equipment will have enough clearance for front and rear access.
„
The IB cables can be accessed easily.
„
Water or moisture cannot enter the switch.
D000140-001 D
1-5
1–Installation
Installation Tasks Checklist
„
The ambient temperature stays between 50° - 113°F (5° - 40° C).
„
Cabinet doors do not interfere with front-to-back air flow.
The cabinet should have its own switchable power distribution. If the switch has
two power supplies, it is suggested that a cabinet with dual power distribution
units is used.
It is recommended that cabinet anti-tip devices are used. This is especially true if
installing or removing a switch in the upper half of the cabinet when the lower half
is empty.
Mark the Rack
Allow enough vertical space in the rack for each specific switch installation.
1-6
1.
Determine the location in the rack of the bottom of the switch.
2.
Mark the upper (if applicable) and lower mounting positions on the vertical
rails on the front of the rack.
3.
Mark the upper (if applicable) and lower mounting positions on the vertical
rails on the back of the rack.
D000140-001 D
1–Installation
12200/12300 Installation
12200/12300 Installation
This section describes the rack mounting instructions for the 12200 and 12300:
Four Post Standard-Depth Rack Installation
In a standard-depth rack, the distance between the front and back mounting posts
is ~28" (700mm). Mounting rails for the 12200 and 12300 are adjustable to
accommodate racks with 26"-33" between mounting posts.
Mounting Hardware Kit Contents:
„
One pair of mounting rails adjustable for 26"-33" installation range
„
One pair of hat rails, left and right
„
#6-32 screws
„
M6 cage nuts
„
M6 screws
1.
Install the hat rails on each side of the switch using three (3) #6-32 screws
per rail. Torque screws to 8in-lb. A typical installation is shown in Figure 1-3..
On the 12300, hat rails are installed with mounting ears towards the power
supply side of the switch. On the 12200, hat rails are installed with mounting
ears towards the port side of the switch. Additionally, 12200 switches can be
installed recessed within a rack. There are four sets of mounting holes on
hat rails, for recess installations of 0, 2, 3 or 4 inches. Use the appropriate
mounting holes to achieve the desired recess.
Installation
Figure 1-3. 12200 and 12300 Hat Rails
D000140-001 D
1-7
1–Installation
12200/12300 Installation
2.
Install eight (8) cage nuts into rack posts, two (2) cage nuts per post. Install
the mounting rails and fasten to cage nuts using six (6) M6 screws. Torque
screws to 30in-lb. Do not install two (2) screws in lower locations on
equipment installation side of the rack until the switch is installed in the rack.
Note the orientation of mounting rails in Figure 1-4.. The rails are shown
from the front side of the rack for 12300 or from the port side of the rack for
12200.
Figure 1-4. Installing the Rack Rails
3.
1-8
Slide the switch into the mounting rails and fasten with M6 screws, one (1)
per side. Torque screws to 30in-lb.
D000140-001 D
1–Installation
12200/12300 Installation
Figure 1-5. 12200 and 12300 Four Post Standard Rack Mounting
12200 Four Post Shallow-Depth Rack Installation
In a shallow-depth rack, the distance between the front and back mounting posts
is ~16" (400mm). Mounting rails for the 12200 are adjustable to accommodate
racks with 14"-20" between mounting posts.
Mounting Hardware Kit Contents:
„
One pair of C-brackets
„
One pair of hat rails, left and right
„
#6-32 screws
„
M6 cage nuts
„
M6 screws
D000140-001 D
1-9
1–Installation
12200/12300 Installation
Installation
1.
Install the hat rails with mounting ears towards the port side of the switch.
Fasten with three (3) #6-32 screws per rail. Torque screws to 8in-lb.
Figure 1-6. 12200 Hat Rails
1-10
2.
Install six (6) cage nuts into the rack posts. Two cage nuts into posts on the
front side of the rack and four cage nuts into posts in the rear of the rack.
Note that the front of the rack is where the switch is installed.
3.
Install two C-brackets in the rear of the rack. Fasten to the rack posts with
four (4) M6 screws. Slide the switch from the front of the rack into the
C-brackets and fasten to the front posts with two (2) M6 screws. Torque to
30in-lb.
D000140-001 D
1–Installation
12200/12300 Installation
Figure 1-7. 12200 Four Post Shallow Rack Mounting
D000140-001 D
1-11
1–Installation
12800-040 Installation
12800-040 Installation
NOTE:
The following procedures are for installing the switch using variable
distances between the front and rear rack posts.
Mounting Hardware Kit Contents
NOTE:
The mounting kit contains all of the necessary parts for installing and
mounting the switch into a 19" 4-post server rack, with a distance between
front and rear rack posts ranging from 28" - 33" (711mm - 838mm).
1-12
„
Support Rails
„
HAT Brackets
„
C-Brackets
„
#8-32 Flat Head Screws
„
M6 Mounting Screws
„
M6 Clip Nuts
D000140-001 D
1–Installation
12800-040 Installation
Installation Tasks
1.
Install the clip nuts. Install M6 clip nuts in the following locations on EIA rails:
Figure 1-8. Clip Nut Installation Locations
For improved stability, orient the clip nuts as shown (that is, orient the
flanges horizontally):
Figure 1-9. Clip Nut Orientation
2.
D000140-001 D
Install support rails in the rack. Fasten with two (2) M6 screws per EIA rail to
pre-installed clip nuts and torque to 30 in-lb.
1-13
1–Installation
12800-040 Installation
Figure 1-10. Support Rail Installation
3.
Orient the chassis such that mounting flanges are in the front of the rack.
Install the chassis in the rack. Fasten chassis to the rack with four (4) M6
screws. Torque to 30in-lb.
WARNING!!
To avoid injury, use a team of people appropriate to the weight of the product
and in conjunction with applicable laws and guidelines.
4.
1-14
Fasten chassis to the rack with four (4) M6 screws. Torque to 30in-lb.
D000140-001 D
1–Installation
12800-040 Installation
Figure 1-11. Rack Installation
5.
D000140-001 D
If applicable, replace the door(s) on the rack.
1-15
1–Installation
12800-120 Installation
12800-120 Installation
NOTE:
The mounting kit contains all of the necessary parts for installing and
mounting the switch into a 19" 4-post server rack, with a distance between
front and rear rack posts ranging from 28" - 33" (711mm - 838mm).
Mounting Hardware Kit Contents:
NOTE:
The mounting kit contains all of the necessary parts for installing and
mounting the switch into a 19" 4-post server rack, with a distance between
front and rear rack posts ranging from 28" - 33" (711mm - 838mm).
„
Support Rails
„
HAT Brackets
„
C-Brackets
„
#8-32 Flat Head Screws
„
M6 Mounting Screws
„
M6 Clip Nuts
Installation Tasks
1-16
1.
If applicable, remove the doors of the rack.
2.
Install the clip nuts Install M6 clip nuts in the following locations on EIA rails:
D000140-001 D
1–Installation
12800-120 Installation
Figure 1-12. Clip Nut Installation Locations
For improved stability, orient the clip nuts as shown (i.e., orient the flanges
horizontally):
Figure 1-13. Clip Nut Orientation
NOTE:
It is recommended that 12800-120 is installed into the rack at 5U or 6U
location. This locates the chassis approximately 12" from the floor and
allows the chassis to be moved onto the support rails by sliding off of the
pallet.
D000140-001 D
1-17
1–Installation
12800-120 Installation
3.
Install support rails in the rack. Fasten with two (2) M6 screws per EIA rail to
pre-installed clip nuts and torque to 30 in-lb.
Figure 1-14. Support Rail Installation
4.
1-18
Install two (2) rear mounting Hat Brackets on the chassis and fasten with
#8-32 screws. There are four (4) screws per bracket. Torque to 30in-lb.
D000140-001 D
1–Installation
12800-120 Installation
Figure 1-15. Hat Bracket Installation
5.
Orient the chassis such that mounting flanges are in the front of the rack.
Install the chassis in the rack.
WARNING!!
To avoid injury, do not manually lift the chassis when fully loaded. Use a
mechanized lift whenever possible. For a manual lift, unload the product
FRUs to minimize the weight. Use a team of people appropriate to the
weight of the product, and in conjunction with applicable laws and
guidelines.
D000140-001 D
1-19
1–Installation
12800-120 Installation
Figure 1-16. Mounting Flange Installation
6.
1-20
Fasten the chassis to the rack with eight (8) M6 screws. Torque to 30in-lb.
D000140-001 D
1–Installation
12800-120 Installation
Figure 1-17. Chassis Installation
7.
D000140-001 D
Slide two (2) C-brackets over the Hat brackets that are pre-installed on the
chassis.
1-21
1–Installation
12800-120 Installation
Figure 1-18. C Bracket Installation
8.
1-22
If applicable, install the optional cable management guides. Fasten to the
EIA rails with M6 screws. Torque all screws to 30in-lb.
D000140-001 D
1–Installation
12800-120 Installation
Figure 1-19. Cable Management Installation
9.
D000140-001 D
If applicable, replace the door(s) on the rack.
1-23
1–Installation
12800-180 Installation
12800-180 Installation
Mounting Hardware Kit Contents:
NOTE:
The mounting kit contains all of the necessary parts for installing and
mounting the switch into a 19" 4-post server rack, with a distance between
front and rear rack posts ranging from 28" - 33" (711mm - 838mm).
„
Support Rails
„
HAT Brackets
„
C-Brackets
„
#8-32 Flat Head Screws
„
M6 Mounting Screws
„
M6 Clip Nuts
Selecting a Rack
The 12800-180 is a large InfiniBand switch capable of supporting up to 432
InfiniBand ports operating at QDR speed. It is designed for installations in
standard-width, 19"-mount server racks (total width of a rack is typically 24").
However, to effectively route and manage such a large number of cables, it is
recommended that a wide server rack is used for installation of 12800-180
switches. Wide 19"-mount server racks are typically 30-32" in total width.
Installation Tasks
NOTE:
It is recommended that 12800-180 is installed into the rack at 5U or 6U
location. This locates the chassis approximately 12" from the floor and
allows the chassis to be moved onto the support rails by sliding off of the
pallet.
1-24
1.
If applicable, remove the doors of the rack.
2.
Install M6 clip nuts in the following locations on EIA rails for U5 installation.
For U6 installation, increment clip nut locations by one U.
D000140-001 D
1–Installation
12800-180 Installation
Figure 1-20. Clip Nut Locations
For improved stability, orient the clip nuts as shown (i.e., orient the flanges
horizontally):
Figure 1-21. Clip Nut Orientation
D000140-001 D
1-25
1–Installation
12800-180 Installation
3.
Install support rails in the rack. Fasten with two (2) M6 screws per EIA rail to
pre-installed clip nuts and torque to 30 in-lb.
Figure 1-22. Support Rail Installation
4.
1-26
Install four (4) rear mounting brackets to the chassis and fasten with #8-32
screws. There are four (4) screws per bracket. Torque to 30in-lb.
D000140-001 D
1–Installation
12800-180 Installation
Figure 1-23. Flat Bracket Installation
5.
D000140-001 D
Orient the chassis such that mounting flanges are in the front of the rack.
Install the chassis in the rack.
1-27
1–Installation
12800-180 Installation
WARNING!!
To avoid injury, when fully loaded do not lift manually. Use a mechanized lift
only. If a manual lift is necessary, first unload all field replaceable units
(FRUs) to minimize weight. Use a team of people appropriate to the weight
of the product and in conjunction with applicable laws and guidelines.
6.
1-28
Fasten the mounting flanges using M6 screws to the clip nuts that are
pre-installed in the rack. There are six (6) screws per mounting flange.
Torque to 30in-lb.
D000140-001 D
1–Installation
12800-180 Installation
Figure 1-24. Mounting Flange Installation
7.
D000140-001 D
Slide four (4) C-brackets over the HAT brackets that are pre-installed on the
chassis.
1-29
1–Installation
12800-180 Installation
Figure 1-25. U Bracket Installation
8.
1-30
If applicable, install the optional cable management guides. Fasten to the
EIA rails with M6 screws. Torque all screws to 30in-lb.
D000140-001 D
1–Installation
12800-180 Installation
Figure 1-26. Cable Management Guide Installation
9.
D000140-001 D
If applicable, replace the door(s) on the rack.
1-31
1–Installation
12800-360 Installation
12800-360 Installation
Mounting Hardware Kit Contents:
NOTE:
The following procedures are for installing the switch using variable
distances between the front and rear rack posts.
„
Mounting Kit containing:
‰
Support Shelf
‰
HAT Brackets
‰
C-Brackets
‰
#10 Mounting screws
‰
M6 Mounting Screws
‰
M6 Clip Nuts
Selecting a Rack
12800-360 is the largest in the 12800-series of switches, capable of supporting up
to 864 InfiniBand ports operating at QDR speed. To facilitate installation and
management of such a large number of cables, the 12800-360 switch was
designed with cables in the front and the rear of the chassis. This reduces cable
density and improves cable management and accessibility.
To effectively route and manage cables, it is recommended that a wide server rack
is used for installation of the 12800-360 switch. These instructions are for
installation in a typical wide server rack 797mm wide x 1021mm deep, or similar,
with adjustable vertical EIA rails.
1-32
D000140-001 D
1–Installation
12800-360 Installation
Figure 1-27. 12800-360 Front and Rear Cabling
D000140-001 D
1-33
1–Installation
12800-360 Installation
Locating Rack Mounting Posts for Front and Back Cable Routing
In a typical rack, front EIA rails are positioned approximately 50mm from the front
face of a rack. With a chassis mounted flush with the front rails, space available in
the front the rack is insufficient for cable routing. To allocate enough space in the
front of the rack to route 300+ cables, the two front rails should be recessed
135mm from the front of the rack. The rear EIA rails should be positioned such
that the distance between mounting surfaces of front and rear EIA rails is 642mm.
Additionally, airflow recirculation control panels should be installed in a rack to
minimize airflow recirculation between the hot and cold isles. Recirculation
control panels for wide racks and installation instructions are available from rack
suppliers.
Figure 1-28. Locating Mounting Posts
1-34
D000140-001 D
1–Installation
12800-360 Installation
Installation Tasks
NOTE:
It is recommended that 12800-360 is installed into the rack at 5U or 6U
location. This will locate the chassis approximately 12" from the floor and will
allow the chassis to be moved onto the support rails by sliding off the pallet.
1.
Install clip nuts: If applicable, remove the doors of the rack. Install M6 clip
nuts in the following locations on EIA rails for U5 installation. For U6
installation, increment clip nut locations by one U (1.75”).
Figure 1-29. Clip Nut Installation
For improved stability, orient the clip nuts as shown (i.e., orient the flanges
horizontally):
D000140-001 D
1-35
1–Installation
12800-360 Installation
Figure 1-30. Clip Nut Orientation
1-36
2.
Attach four (4) mounting brackets to the support shelf as shown in
Figure 1-31. Align the brackets with "B" marks on a support shelf and fasten
with six (6) M6 HEX screws per bracket. Use a HEX socket wrench to
tighten the screws. Torque the screws to 120in-lb.
3.
Attach the support bracket to the support shelf and fasten with seven (7)
#10-32 flat head screws. Torque screws to 30in-lb.
D000140-001 D
1–Installation
12800-360 Installation
Figure 1-31. Support Shelf Assembly
4.
D000140-001 D
Install the support shelf into the rack. Fasten the M6 screws to pre-installed
clip nuts and torque to 30 in-lb. There are three (3) screws per mounting
bracket.
1-37
1–Installation
12800-360 Installation
Figure 1-32. Attaching the Support Shelf to the Rack
5.
1-38
Orient and position the chassis for installation in the rack.
D000140-001 D
1–Installation
12800-360 Installation
WARNING!!
To avoid injury, when fully loaded do not lift the 12800-260 manually. Use a
mechanized lift only. If a manual lift is necessary, first unload all field
replaceable units (FRUs) to minimize weight. Use a team of people
appropriate to the weight of the product and in conjunction with applicable
laws and guidelines.
6.
D000140-001 D
Orientation of the chassis on a pallet: The chassis has been packaged on
sliding surfaces to facilitate installation in a rack by sliding off of the pallet
and on the support shelf. Remove the rear foam block to expose sliding
surfaces. The rear of the chassis is oriented towards a cutout in the bottom
tray.
1-39
1–Installation
12800-360 Installation
Figure 1-33. Loading from the Pallet
7.
1-40
Position the chassis on front on the rack. Use pallet jack to move the
chassis. Orient the chassis on a pallet in front of the rack as shown. Chassis
rear should be facing front of the rack. For installations in racks arranged in
rows, distance between adjacent rows of racks (width on a cold isle) should
be greater than 36" to be able to move the chassis on a pallet through a cold
isle.
D000140-001 D
1–Installation
12800-360 Installation
Figure 1-34. Positioning the Switch
8.
D000140-001 D
Installing the chassis in the rack: Align the chassis with the rack. Raise the
chassis using a pallet jack such that the bottom of the chassis is at or slightly
higher than the top surface of the support shelf pre-installed in the rack. Lock
the pallet jack wheels. Use a group of people to push the chassis from the
front to slide it off the pallet and on the support shelf. The chassis should be
inserted into the rack until the rear of the chassis base is against the rear
support bracket.
1-41
1–Installation
12800-360 Installation
Figure 1-35. Sliding the Switch off the Pallet
9.
1-42
Fasten the front of the chassis to the rack by installing the front support
bracket and fasten to the base of the chassis with five (5) M6 screws. Fasten
to the support shelf with seven (7) #10-32 screws. Torque to 30 in-lb.
D000140-001 D
1–Installation
12800-360 Installation
Figure 1-36. Fasten the Chassis to the Front of the Rack
10.
Fasten the rear of the chassis to the rack: Fasten the rear support bracket to
the base of the chassis with five (5) M6 screws. Torque to 30 in-lb.
11.
Install two (2) C-brackets by sliding over the H-brackets that are pre-installed
on the chassis.
D000140-001 D
1-43
1–Installation
12800-360 Installation
Figure 1-37. Fasten the Chassis to the Back of the Rack
1-44
D000140-001 D
1–Installation
12800-360 Installation
12.
Attach the cable management guides.
If applicable, attach the cable management guides to the front and rear EIA
mounting rails, and fasten with M6 screws to the pre-installed clip nuts. The
guides should be installed such that the wireframe supports line up with the
chassis leaf module slots. There are four (4) guides in the front of a rack and
four (4) in the rear of a rack.
Figure 1-38. Attaching Cable Management Guides
13.
D000140-001 D
If applicable, replace the door(s) on the rack.
1-45
1–Installation
Connect Equipment to the Ports and Power On the System
Connect Equipment to the Ports and Power On
the System
NOTE:
Before connecting equipment, it is important to understand the locations of
the serial and Ethernet ports on the 12200, 12300 and 12800 series. For the
12200 and 12300, these are located on the switch IB port side. For the
12800 series, these are located on the Serial, Ethernet, Chassis EEPROM
Board (SEEB) modules. Each SEEB module communicates with a
Management Module (MM) on the opposite side of a 12800 chassis.
Figure 1-39. 12200 and 12300 Serial and Ethernet Ports
Figure 1-40. 12800 Series Serial and Ethernet Ports (SEEB Module)
1-46
D000140-001 D
1–Installation
Connect Equipment to the Ports and Power On the System
1.
Connect a Category 5 or 6 (Cat 5/6) Ethernet cable to the RJ-45
connector(s) on the switch. Connect the other end of the Cat 5/6 to an OOB
LAN workstation, another switch or a hub.
2.
Connect the switch to IB-enabled host(s)/switch(es) using QDR QSFP IB
cables, or to DDR host(s)/switch(es) using a QSFP-CX4 cable.
NOTE:
Make sure all cables latch securely into the corresponding port connectors.
If the IB cable connector is not properly oriented to fit onto the port
receptacle (i.e., while attempting to insert the cable in the port), do not twist
the connector to achieve the correct orientation. Instead, reach back a few
feet on the cable, and twist the bulk cable to allow the connector to rotate to
the proper orientation. Doing this prevents all of the rotational forces from
acting right at the connector terminations.
CAUTION!
It is important to provide strain relief for the IB cable connector.
Connecting Power
NOTE:
For each power supply installed, a power cord must be installed in
corresponding power inlet.
1.
Provide strain relief for the power cable(s).
2.
If necessary, replace the fascia(s) over the switch fans.
3.
Connect the power cables to a power distribution unit (PDU) or a proper AC
power outlet.
4.
When the switch is plugged into an AC power outlet:
D000140-001 D
a.
The system powers up.
b.
The fans start.
c.
The system performs a power-on self test (POST).
1-47
1–Installation
Connect Equipment to the Ports and Power On the System
NOTE:
For the 12800 switches, make certain the DC ON/OFF switch is illuminated.
If it is not, press the button to supply power. The switch is located:
„ 12800-360: Next to the AC power inlets on the top of the chassis.
„ 12800-040: Next to the AC power inlets.
„ 12800-180 and 12800-120: Next to the power supplies. If applicable, the
user needs to remove the fascia covering the supplies to access the DC
ON/OFF switch.
Figure 1-41. DC ON/OFF Switch
5.
1-48
The switch, power supply, and fan LEDs light up.
D000140-001 D
1–Installation
Bringing Up the System For the First Time
Bringing Up the System For the First Time
12800-Series Management Module Protective Label
Guidelines
A management module installed in a 12800 system may have a protective label
installed, as shown in Figure 1-42. This label protects the mechanical release
latch (MRL) switch inside the management module from shock and vibration
during shipping.
Figure 1-42. MRL Protective Label 1
Staging Area Testing
If a MM requires testing prior to final installation at an end-user site (for example,
testing at a staging area), do the following:
1.
Disengage the thumb screw and partially rotate the lever as shown in
Figure 1-43.
Figure 1-43. MRL Protective Label 2
2.
D000140-001 D
Fold back the label from the thumb screw hole. Re-engage the lever and
tighten the thumb screw as shown in Figure 1-44.
1-49
1–Installation
Bringing Up the System For the First Time
Figure 1-44. MRL Protective Label 3
3.
After testing is complete at the staging area, reverse Steps 1 and 2 to
prepare the system for shipment to the end-user site (see Figure 1-45).
Figure 1-45. MRL Protective Label 4
User Site Installation
After final installation of a 12800-series switch is completed at the end user site:
1.
Disengage the thumb screw and partially rotate the lever as shown in
Figure 1-46.
Figure 1-46. MRL Protective Label 5
1-50
D000140-001 D
1–Installation
Bringing Up the System For the First Time
2.
Peel off the protective label. Re-engage the lever and tighten the thumb
screw as shown in Figure 1-47.
Figure 1-47. MRL Protective Label 6
Start-up Procedures
1.
Power up the switch.
2.
From its flash image on the management module, the switch begins its boot
process.
NOTE:
If the DB9 port of the SEEB module or the RS232 port on the 12200/12300
is connected to a terminal emulation program, the user will be able to view
the switch boot process. Be certain to use a null-modem/crossover serial
cable for the console port. For users assembling their own cable, refer to
Appendix C for serial port pinout information. The settings for the terminal
emulation device should be:
„ 8 data bits
„ no parity bits
„ 1 stop bit
„ 57.6K baud
„ Use VT100 emulation.
„ Flow control = XON/XOFF
3.
Verify the IP address with the command line interface (CLI) command
showChassisIpAddr command. The system returns information similar to
the following:
Chassis IP Address: 192.168.100.9 Net mask:
255.255.240.0
D000140-001 D
1-51
1–Installation
Bringing Up the System For the First Time
Changing the Switch IP Address and Default Gateway via the
CLI
The command line interface (CLI) can be accessed via Telnet, SSH, the SEEB
module DB-9 or 12200/12300 RS-232 serial port(s).
1.
Determine the CLI access method (that is, Telnet, SSH, or Serial).
NOTE:
If using a serial port, skip to Step 6. Steps 2 through 5 are for those users
accessing the switch via Telnet or SSH. For the 12800 series, make certain
to connect to the SEEB serial port associated witht the Master Management
Module (MM). These are:
„ 12800-040: MM 201
„ 12800-120: MM 207
„ 12800-180: MM 211
„ 12800-360: MM 227
2.
3.
Connect appicable serial cables to the RS-232/DB-9 ports of the switch.
Connect the other end to a workstation. If using a terminal emulation device,
the settings should be:
„
8 data bits
„
no parity bits
„
1 stop bit
„
57.6K baud
„
Use VT100 emulation.
„
Flow control = XON/XOFF
If using Telnet or SSH, access the switch with the following command:
open 192.168.100.9
4.
The system prompts for a user name. In order to change the IP address and
default gateway, the user must be logged in as the administrator. At the
prompt enter:
admin
5.
The system prompts for a password. At the prompt enter:
adminpass
The system responds with:
1-52
D000140-001 D
1–Installation
Bringing Up the System For the First Time
Welcome to the <SWITCH> CLI. Type 'list' for the list of
commands.
6.
To change the switch IP address enter:
setChassisIpAddr -h ipaddress -m netMask
where -h ipaddress is the new IP address in dotted decimal (i.e.,
xxx.xxx.xxx.xxx) format, and -m netMask is the new subnet mask in dotted
decimal (i.e., xxx.xxx.xxx.xxx) format.
7.
To change the switch default gateway IP address enter:
setDefaultRoute -h ipaddress
where -h ipaddress is the new default gateway IP address in dotted
decimal (i.e., xxx.xxx.xxx.xxx) format.
8.
To to exit the CLI enter:
logout
Updating the Management Module IP Addresses in a
Redundant Management Configuration (12800-040,
12800-120, 12800-180 and 12800-360)
Each management module must have a unique IP address that is different than
the chassis IP address of the switch. Therefore, a redundantly-managed switch
will have multiple unique IP addresses.The default IP addresses are:
12800-040
„
Chassis: 192.168.100.9
„
Management Module 201: 192.168.100.10
„
Management Module 202: 192.168.100.11
12800-120
„
Chassis: 192.168.100.9
„
Management Module 207: 192.168.100.10
„
Management Module 208: 192.168.100.11
12800-180
„
Chassis: 192.168.100.9
„
Management Module 211: 192.168.100.10
„
Management Module 212: 192.168.100.11
12800-360
„
D000140-001 D
Chassis: 192.168.100.9
1-53
1–Installation
Bringing Up the System For the First Time
„
Management Module 227: 192.168.100.10
„
Management Module 228: 192.168.100.11
It is necessary for each management module to have a unique IP address for the
following reasons:
„
Unique IP addresses are used when sending syslog messages from a
managed spine to a syslog server.
„
Gives the user the ability to ping each management spine separately.
„
If the IP addresses are not unique, collisions will occur, causing IP
operations to fail.
To update the IP address on a management module, do the following:
1.
Ensure that the module is connected to a COM port on a serial terminal
device via the RS-232 port (12200/12300) or DB-9 port (12800 series).
2.
Get to a [boot]: prompt by following Step a or b.
a.
If the management module is running and displays the -> prompt, enter
the following command at the console:
reboot now
Then press Enter.
b.
If the module is not running, power on the switch.
3.
When the system displays image1 or image2, press the Spacebar to
interrupt the auto load sequence before the counter expires (within 5
seconds).
4.
At the [boot]: prompt type the following:
moduleip <NEW IP ADDRESS>
Then press Enter.
NOTE:
For versions previous to 5.0.2, use the command spineip.
NOTE:
This command changes the IP address for image1 and image2 on each
module.
5.
1-54
At the [boot]: prompt enter reboot, and press Enter. Upon reboot the IP
address is changed. Repeat for the second Management Module.
D000140-001 D
1–Installation
Bringing Up the System For the First Time
Enabling 8X Ports
Users can enable 8X (10 Gbps) ports by combining two (2) 4X ports together (also
known as a “DUO”). The first port in a DUO is known as the master port; the
second port is the partner or slave port. The following CLI commands can enable
8x ports:
„
ismPortSetWidth: sets the supported link width for an individual IB port.
„
ismChassisSetWidth: sets the supported link width for all chassis IB
ports.
„
ismIslSetWidth: sets the supported link width for all interswitch link (ISL)
IB ports. This command is only available 12800-series switches.
NOTE:
This section focuses on enabling 8x external cable ports. For details on each
command, refer the QLogic 12000 CLI Reference Guide.
Creating an 8x Port: 12200/12300
For the 12200 and 12300 switches, 8x DUOs are set up by combining the 4X port
on the bottom row with the 4X port directly above it (for example, port 1 with port
19, port 2 with 20, port 3 with port 21, etc.):
Figure 1-48. 12200/12300 8x DUOs
For example, to combine ports 2 and 20:
1.
Log into the switch CLI with the login admin and password adminpass.
2.
Enable port 2 with a command similar to:
ismPortSetWidth Cable02 7 -bounce.
and press Enter.
3.
D000140-001 D
Enable port 20 using same command as above, changing the port number
(that is, Cable20).
1-55
1–Installation
Bringing Up the System For the First Time
4.
At the switch, unplug and reinsert the cables to the physical ports. After
reinserting the first cable, the user has four (4) seconds to reinsert the
second cable associated with the 8x connection before the link begins
training.
NOTE:
For proper 8x functionality, it is required that both QSFP cables for a DUO
are from the same manufacturer, as well as the same length.
5.
After reinserting the cables, bring up Chassis Viewer. The 8X ports are
displayed as shown in Figure 1-49 where both ports of the DUO have LEDs
on (that is, they are green).
Figure 1-49. 8X Ports Enabled
6.
1-56
From the Chassis Viewer main menu, click on Port Stats then IB Port Stats
to display the IB Port Statistics screen. The 8X port (for DUO of cable ports
10 and 28) is displayed as shown in Figure 1-50.:
D000140-001 D
1–Installation
Bringing Up the System For the First Time
Figure 1-50. 8X Port Statistics
The first port of the group (port 10) is shown as active and Up, while the other port
in the DUO (port 28) is displayed as down and Disabled.
D000140-001 D
1-57
1–Installation
Bringing Up the System For the First Time
Creating an 8x Port: 12800 Series
For the 12800 switches, 8x DUOs are set up on the leaf modules as follows:
UHP Leaf (18 4x QDR ports): combine the 4X port on the bottom row with the 4X
port directly above it (for example, port 1 with port 10, port 2 with 11, port 3 with
port 12, etc.).
UHD Leaf (24 4x QDR ports): for ports 1 through 18, combine the 4X port on the
bottom row with the 4X port directly above it (for example, port 1 with port 10, port
2 with 11, port 3 with port 12, etc.). For ports 19 through 24 DUOs are made by
combing the ports sequentially (that is, port 19 and port 20, port 21 and port 22,
and port 23 and port 24).
Figure 1-51. 12800 Leaf Module 8x DUOs
For example, to combine ports 8 and 17 on UHP leaf 111 in a 12800-180 switch:
1.
Log into the switch CLI with the login admin and password adminpass.
2.
Enable port 8 with a command similar to:
ismPortSetWidth L111P08 7 -bounce.
and press Enter.
1-58
3.
Enable port 17 using same command as above, changing the port number
(that is., L111P17).
4.
At the switch, unplug and reinsert the cables to the physical ports. After
reinserting the first cable, the user has four (4) seconds to reinsert the
second cable associated with the 8x connection before the link begins
training.
D000140-001 D
1–Installation
Bringing Up the System For the First Time
NOTE:
For proper 8x functionality, it is required that both QSFP cables for a DUO
are from the same manufacturer and the same length.
5.
After reinserting the cables, bring up Chassis Viewer. The 8X ports are
displayed as shown in Figure 1-52 where both ports of the DUO have LEDs
on.
Figure 1-52. 8X Ports Enabled
6.
D000140-001 D
From the Chassis Viewer main menu, click on Port Stats then IB Port Stats
to display the IB Port Statistics screen. The 8X port (for DUO of cable ports 8
and 17) is displayed as shown in Figure 1-53.:
1-59
1–Installation
Bringing Up the System For the First Time
Figure 1-53. 8X Port Statistics
The first port of the group (port 8) is shown as active and Up, while the other
port in the DUO (port 17) is displayed as down and Disabled.
1-60
D000140-001 D
1–Installation
Component LEDs
Component LEDs
Management Module
Figure 1-54. Management Module LEDs
Module Status
The status LED indicates one of the following conditions:
„
Steady Green - the module is operating normally.
„
Blinking Green - LED test state.
„
Off - module is in the removable state.
Module Attention
The Attention LED indicates one of the following conditions:
„
Off - the system is functioning normally.
„
Steady Amber - the system requires some attention, which could indicate
one of the following conditions:
„
D000140-001 D
‰
The switch temperature is at a warning level on the module.
‰
The switch silicon temperature is at a warning level (approximately 90
degrees C).
‰
DC voltages on the board are slightly out of tolerance (12V Bulk, 5V,
3.3V and 1.8V are all monitored).
‰
The module can no longer function properly. The system will take the
appropriate actions to ensure that no damage is done to its
components.
Blinking Amber (once every four seconds) - LED test state, which could
indicate one of the following conditions:
‰
Bulk power is stable.
‰
The module DC-to-DC converter is enabled.
1-61
1–Installation
Component LEDs
‰
The module is not removable.
Chassis Status and Attention
The chassis status LED is Green when the system is functioning normally.
The chassis status LED is Amber when one of the following conditions exists:
„
Any Fan Alarm is amber.
„
Any power supply AC OK LED is off.
„
Any power supply DC OK LED is off
„
Any spine module Attention LED is on, or it has been determined that a
spine is not functioning (even if it is unable to turn on the LED).
„
Any leaf module Attention LED is on, or it has been determined that a leaf is
not functioning (even if it is unable to turn on the LED).
The chassis status LED is Amber when the system can no longer function
properly and indicates one of the following conditions:
„
No functional fan trays are present.
„
No functional spines are present.
„
No functional leaves are present.
The chassis status LED is off when:
„
There are no functional power supplies present.
„
There are no management cards in the system
„
AC power has been removed from the system.
Fault Tolerant
The Chassis Fault Tolerant (FT) LED indicates the following condition:
„
Steady Green - the chassis is populated with a full complement of fans as
well as N+1 power.
Service Required
The chassis service required (SVC) LED is not currently implemented.
Master
The Master LED is Green when module is acting as the master Management
Module (i.e., it is the master MM).
MRL Active
The MRL Active LED is Green when mechanical release latch (MRL) thumbscrew
is secured to the Serial, Ethernet, Chassis EEPROM Board (SEEB).
1-62
D000140-001 D
1–Installation
Component LEDs
Figure 1-55. MRL Active LED
D000140-001 D
1-63
1–Installation
Component LEDs
Leaf Module
Figure 1-56. Leaf Module LEDs
IB Port LEDs
Each module IB port has a Green IB link status LED that provide the following
indications:
„
On - the logical link is up (port is in the Active state).
„
Off - the physical link is down (port is in the Down state).
Module Status
The status LED indicates one of the following conditions:
„
Steady Green - the module is operating normally.
„
Blinking Green - LED test state.
„
Off - module is in the removable state.
Module Attention
The Attention LED indicates one of the following conditions:
1-64
D000140-001 D
1–Installation
Component LEDs
„
Off - the system functioning normally.
„
Steady Amber - the system requires some attention, which could indicate
one of the following conditions:
„
‰
The switch temperature is at a warning level on the module.
‰
The switch silicon temperature is at a warning level (approximately 90
degrees C).
‰
DC voltages on the board are slightly out of tolerance (12V Bulk, 5V,
3.3V and 1.8V are all monitored).
‰
The module can no longer function properly. The system will take the
appropriate actions to ensure that no damage is done to its
components.
Blinking Amber (once every four seconds) - LED test state.
Spine Module
Figure 1-57. Spine Module LEDs (Double Spine Shown)
Module Status
The status LED indicates one of the following conditions:
„
Steady Green - the module is operating normally.
„
Blinking Green - LED test state.
„
Off - module is in the removable state.
Module Attention
The Attention LED indicates one of the following conditions:
„
Off - the system functioning normally.
„
Steady Amber - the system requires some attention, which could indicate
one of the following conditions:
D000140-001 D
1-65
1–Installation
Component LEDs
„
„
The switch temperature is at a warning level on the module.
„
The switch silicon temperature is at a warning level (approximately 90
degrees C).
„
DC voltages on the board are slightly out of tolerance (12V Bulk, 5V,
3.3V and 1.8V are all monitored).
„
The module can no longer function properly. The system will take the
appropriate actions to ensure that no damage is done to its
components.
Blinking Amber (once every four seconds) - LED test state.
SEEB Module
Figure 1-58. SEEB Module LEDs
RJ45 LEDs
The RJ45 connectors have two LEDs, Act and 100. The 100 LED is Green when
a 100Mbps link is connected. The Act LED is Amber when an Ethernet link has
been established, and blinking when the link is active.
MRL Active
The MRL Active LED is Green when the mechanical release latch (MRL)
thumbsrew is secured to the Serial, Ethernet, Chassis EEPROM Board (SEEB)
and a Management Module is installed in the front of the chassis.
1-66
D000140-001 D
1–Installation
Component LEDs
12200 and 12300
Figure 1-59. 12200 and 12300LEDs
IB Port LEDs
Each module IB port has a Green IB link status LED that provide the following
indications:
„
On - the logical link is up (port is in the Active state).
„
Off - the physical link is down (port is in the Down state).
Status
The status LED indicates one of the following conditions:
„
Steady Green - the module is operating normally.
„
Blinking Green - LED test state.
„
Off - module is in the removable state.
Attention
The Attention LED indicates one of the following conditions:
„
Off - the system functioning normally.
„
Steady Amber - the system requires some attention, which could indicate
one of the following conditions:
D000140-001 D
‰
The switch temperature is at a warning level on the module.
‰
The switch silicon temperature is at a warning level (approximately 90
degrees C).
1-67
1–Installation
Component LEDs
„
‰
DC voltages on the board are slightly out of tolerance (12V Bulk, 5V,
3.3V and 1.8V are all monitored).
‰
The module can no longer function properly. The system will take the
appropriate actions to ensure that no damage is done to its
components.
Blinking Amber (once every four seconds) - LED test state.
RJ45 LEDs
The RJ45 connectors have two LEDs, Act and 100. The 100 LED is Green when
a 100Mbps link is connected. The Act LED is Green when an Ethernet link has
been established, and blinking when the link is active.
12800 Fans and Power Supplies
Fan LEDs
Figure 1-60. 12800 Fan LEDs
Fan LEDs indicate the following status(es):
1-68
„
Green indicates that the fan is functioning properly.
„
Amber indicates that the following warning condition exists:
D000140-001 D
1–Installation
Component LEDs
‰
„
A single fan failure when the rotation speed is less than 4000 RPM or
greater than 10950 RPM.
Green and Amber on indicates a possible problem, including:
‰
The fan tray is not responding to commands for configuration and
temperature-related operations.
‰
A fan is not responding to commands for temperature and speed
related operations.
‰
The fan speed has fallen below the minimum allowed RPM for a fan.
Power Supply LEDs
Figure 1-61. 12800 Power Supply LEDs
Each power supply has three LEDs: DC OK, AC OK and Alarm. Following are the
status definitions for each.
DC OK
„
Green indicates that DC power is normal.
„
Off indicates a DC power failure or no DC power is present.
„
AC OK
„
Green indicates that AC power is normal.
„
Off indicates a AC power failure or no AC power is present.
Alarm
„
D000140-001 D
Amber indicates a fault condition, failed fan, over temperature condition.
1-69
1–Installation
Switch-Based QLogic Fabric Manager License Key
Switch-Based QLogic Fabric Manager License
Key
If purchased, certain packages of the InfiniBand Fabric Suite entitle the user to the
switch-based QLogic Fabric Manager. Refer to the licensing documentation that
comes with the InfiniBand Fabric Suite for instructions on generating the license
key.
Figure 1-62. InfiniBand Fabric Suite Licensing Information
1-70
D000140-001 D
1–Installation
Switch-Based QLogic Fabric Manager License Key
Procedures
1.
Record the IFS serial number.
2.
Go to the QLogic Feature Activation/License Key web site
http://lk.qlogic.com.
Figure 1-63. License Key Activation Center 1
3.
Enter the InfiniBand Fabric Suite serial number. Click Continue. The system
validates the serial number and displays the following screen:
Figure 1-64. License Key Activation Center 2
D000140-001 D
1-71
1–Installation
Switch-Based QLogic Fabric Manager License Key
4.
Click Activate License Key and click Continue. The following screen is
displayed:
Figure 1-65. License Key Activation Center 3
5.
1-72
Enter your email address in the Email: and Confirm Email: text boxes.
Click Continue. The following screen is displayed:
D000140-001 D
1–Installation
Switch-Based QLogic Fabric Manager License Key
Figure 1-66. License Key Activation Center 4
6.
D000140-001 D
Enter all applicable information. For the City: and/or the Zip/Postal Code
entries, click on the flashlight hyperlinks. The following is displayed:
1-73
1–Installation
Switch-Based QLogic Fabric Manager License Key
Figure 1-67. License Key Activation Center 5
7.
In the City: and Zip: text boxes, enter the applicable information and click
Search. Alternatively, search through the list of cities, click the applicable
radio button, then click Search. The following is displayed:
Figure 1-68. License Key Activation Center 6
8.
1-74
If the information is correct, click Close. The following screen is displayed:
D000140-001 D
1–Installation
Switch-Based QLogic Fabric Manager License Key
Figure 1-69. License Key Activation Center 7
9.
D000140-001 D
Click Continue. The following screen is displayed:
1-75
1–Installation
Switch-Based QLogic Fabric Manager License Key
Figure 1-70. License Key Activation Center 8
10.
In the GUID: text box, enter the FRU GUID of the following applicable
components:
„
QLogic 12300 chassis
„
QLogic 12800 series Management Module to be used as the master
subnet manager
‰
Master and redundant switch-based QLogic Fabric Manager
license keys can be generated by entering the GUID of the
primary and redundant management modules in the GUID: text
boxes.
Click Continue. A license key will be emailed.
1-76
D000140-001 D
1–Installation
Switch-Based QLogic Fabric Manager License Key
NOTE:
The FRU GUID can be found:
„ On the label of each FRU.
„ Using the Chassis Viewer, the View FRU button for each applicable
chassis or module FRU.
„ For the12300 via the switch Command Line Interface (CLI), using the
command showIBNodeDesc.
„ For the 12800 series via the switch Command Line Interface (CLI), using
the command ShowInventory. From the system output, locate the GUID
of the Management Module that will be used to apply the license key.
D000140-001 D
1-77
1–Installation
QLogic 12000 Six-Port Upgrade
QLogic 12000 Six-Port Upgrade
Users can order a six-port License Key upgrade for the QLogic 12300-BS18
advanced 40Gb/s QDR InfiniBand switch. Refer to the licensing documentation
that comes with the QLogic 12300-BS18 switch for instructions on generating the
license key.
Figure 1-71. InfiniBand Fabric Suite Licensing Information
1-78
D000140-001 D
1–Installation
QLogic 12000 Six-Port Upgrade
Procedures
1.
Record the 12300-BS18 serial number.
2.
Go to the QLogic Feature Activation/License Key web site
http://lk.qlogic.com.
Figure 1-72. License Key Activation Center
3.
Enter the 12300-BS18 serial number. Click Continue. The system validates
the serial number and moves to the next screen.
4.
Click Activate License Key and click Continue.
5.
Enter your email address in the Email: and Confirm Email: text boxes.
Click Continue.
6.
Enter all applicable contact information. Click Continue.
7.
Enter the transaction code and switch GUID, then click Continue.
NOTE:
The FRU GUID can be found:
„ On the label of each 12300-BS18 switch.
„ Using the Chassis Viewer, the View FRU button for each
applicable chassis.
„ For the12300-BS18 via the switch Command Line Interface (CLI),
using the command showIBNodeDesc.
8.
If the information displayed is correct, click Yes.
9.
Review the end-user license agreement, then click Agree.
10.
The screen displays the generated license key, along with the updated port
count status. To send this information to another user, enter an email
address and click Send. When finished, click Done.
D000140-001 D
1-79
1–Installation
QLogic 12000 Six-Port Upgrade
1-80
D000140-001 D
A
QLogic 12000 Series
Product Specifications
Physical Specifications
All products within the 12200, 12300 and 12800 Director series are designed to be
installed in industry-standard 19-inch four-post server racks.
Racks should conform to conventional standards. Use the American National
Standards Institute (ANSI)/Electronic Industries Association (EIA) standard
ANSI/EIA-310-D-92 and International Electrotechnical Commission (IEC) 297.
These racks are commercially available in various depths. It is recommended to
use rack with minimum of 36" depth to facilitate cable installation and routing.
Other physical attributes are shown in the table below.
NOTE:
The 12000 series products should not be installed in two-post
telecommunication racks.
Table A-1. 12000 Physical Attributes
Model #
12200
12300
12800-0
40
12800-12
0
12800-18
0
12800-36
0
Height (rack
units/inches)
1U/1.75"
1U/1.75"
5U/8.75”
10U/17.5"
14U/24.5"
29U/50.7”
Depth (without cables)
24”
25 3/4" (654mm)
Width
Max weight
(lb./kg.)
D000140-001 D
17.32" (440mm)
15/6.8
26/11.8
100/45.5
155/70.5
285/129.3
536/243.1
A-1
A–QLogic 12000 Series Product Specifications
Environmental Specifications
Environmental Specifications
„
Operating temperature:
‰
„
Non-operating temperature:
‰
„
5°–40°C at sea level, altitude derating 1°C per 300m to 2,400m
-40°C to 65°C
Relative humidity (non-condensing):
‰
Operating 5% - 85%; Non-operating 5% - 90%
12200 and 12300
Cooling and Thermal Management:
„
Cooling:
‰
Air cooled with a hot plug fan/power tray, three fans per tray, 40mm,
12VDC (12300)
‰
Four fans, no fan trays (12200)
‰
Front-to-back airflow
NOTE:
The 12200 also offers a reversed airflow model
Power
„
A-2
Power Supply:
‰
Two redundant, hot plug fan/power supplies (12300)
‰
90/264 VAC operation
‰
275W max power per supply
‰
Input: 90–264V AC, 47–63Hz, 1 Phase, 3.6A max current at 100VAC
‰
Inrush Current: 13A @ 115VAC, 6.5A @ 230VAC
‰
Power Factor: 95% @ 230VAC, 50% load
‰
Power Inlet Plug: two IEC 320-c14 connectors for independent AC
inputs (12300)
D000140-001 D
A–QLogic 12000 Series Product Specifications
12800 Series
12800 Series
All 12800 series switches use the same fan tray modules -- intake and exhaust -and share the same thermal management attributes listed below. The quantity of
fan tray modules used in each system is defined in the following table:
Table A-2. 12800 Product Configurations
Maximum
360
180
120
040
Maximum
InfiniBand
Ports
864
432
288
96
Maximum
Leaf Modules
36
18
12
4
9 Double
4 Double,
1 Single
2 Double,
1 Single
1 Double
2
2
2
2
10/10
5/3
5/3
4/0
12
6
4
4
Maximum
Spine Modules
Management
Modules
Fan Trays
(Intake/
Exhaust)
Power Supplies
„
Fan Tray:
‰
„
Chassis airflow:
‰
„
Hot plug with one axial, brushless, 12V fans per Fan Tray
Front-to-back
Power supply airflow:
‰
Front to back
NOTE:
It is recommended that the 120, 180 and 360 be installed as follows:
„ Intake fan side towards the cold aisle
„ Exhaust fan side towards the hot aisle
„
D000140-001 D
Thermal management:
A-3
A–QLogic 12000 Series Product Specifications
12800 Series
‰
Temperatures of all major heat producing components are
continuously monitored by system management modules. Fan speed
is monitored and automatically adjusted by system management
modules to maintain appropriate temperatures of major heat producing
components. Monitoring is performed via a two wire I2C interface to
each Fan Tray.
Power Specifications
All products within the 12800 series use a common switching power supply.
System power attributes are shown in the table below. Power supplies are are
N+1 redundant and hot pluggable.
NOTE:
An AC power cord is required for each power supply. Refer to the table
below.
Table A-3. System Power Attributes
Model #
A-4
12800-360
12800-180
12800-120
12800-040
Maximum #
of Power
Supplies
12
6
4
4
Maximum
wattage, fully
configured
7,455
3,654
2,735
922
Minimum
required
power
supplies
6
3
3
2
Power
supplies
required for
DC (N+1)
redundancy
7
4
3
2
Power
supplies
required for
AC
redundancy
12
6
4
2
D000140-001 D
A–QLogic 12000 Series Product Specifications
12800 Series
Table A-3. System Power Attributes (Continued)
Model #
12800-360
12800-180
Maximum
output per
supply
90-264 VAC autoranging
Input
frequency
and phase
47-63 Hz
Maximum
current per
supply
100Amps
Inrush
Current
30Amps Max
Power Factor
efficiency
99% @ 230V, full load
Power Inlet
connector
# of Power
Inlets
Power Cord
connector
12800-040
1200 Watts
Input voltage
D000140-001 D
12800-120
IEC320-C20
12
6
4
4
IEC320-C19
A-5
A–QLogic 12000 Series Product Specifications
12800 Series
Power Distribution Guidelines
The following section details power distribution guidelines and recommendations
for the QLogic 12800 series.
„
The power supplies for the 12800 series has a maximum inlet current of
15amps @ 110volts and 6amps @ 220volts. Please observe power outlet,
power strip and extension cable ratings.
„
Do not exceed 80% of the ampere rating limit of the power outlet, power
strip or an extension cable that the equipment is plugged into. As such, the
power delivery system must be that the power supplies do not overpower
the maximum amperage of any given system. For the 12800-360 and
12800-180 it is recommended to power the systems over 220 volts.
CAUTION!
High-powered systems, such as the 12800-180 and 12800-360 can place
significant loads on power distribution units (PDUs) and uninterupable power
supplies (UPSs). It is recommended to measure the total amperage and
power that a PDU or UPS needs to handle
A-6
D000140-001 D
A–QLogic 12000 Series Product Specifications
12800 Series
Figure A-1. 12800-Series Power Distribution
Table A-4. AC Plug Types
D000140-001 D
Region/Countr
y
Voltage
Rating
North America
100-127
NEMA
5-20P
North America
200-240
NEMA
L6-20P
North America
200-240
NEMA
L15-30P
Plug Type
Misc/Notes
Three phase AC
A-7
A–QLogic 12000 Series Product Specifications
12800 Series
Table A-4. AC Plug Types
A-8
Region/Countr
y
Voltage
Rating
Plug Type
Misc/Notes
Europe (Schuko)
200-240
CEE 7/7
Used in Austria, Belgium,
Finland, France, Germany,
Greece, Hungary, Indonesia,
The Netherlands, Norway,
Poland, Portugal, Russia,
Spain, Sweden.
International
200-240
IEC 309
3-wire (two-phase & earth).
Connector size and color
variations are used to indicate
amperage rating. This is
utilized in Switzerland for 16A
applications.
Internationalt
200-240
IEC 309
4-wire (three-phase & earth).
Connector size and color
variations are used to indicate
amperage rating.
International
200-240
IEC 309
5-wire (three-phase, earth &
neutral). Connector size and
color variations are used to
indicate amperage rating.
D000140-001 D
A–QLogic 12000 Series Product Specifications
12800 Series
D000140-001 D
A-9
A–QLogic 12000 Series Product Specifications
12800 Series
Notes
A-10
D000140-001 D
B
Safety and Regulatory
Compliance Information
This section provides regulatory compliance, safety and electromagnetic
compatibility (EMC) information for the QLogic 12000 series products.
Safety Information
Statement 1:
Disconnect Device - This unit may have more than one power cord. To reduce the
risk of electrical shock, disconnect all power cords before servicing unit.
Verklaring 1:
Apparaat loskoppelen - Deze eenheid heeft mogelijk meer dan een stroomkabel.
Verminder het risico op een elektrische schok door alle stroomkabels los te
koppelen voordat u onderhoud pleegt aan de eenheid.
Varoitus 1:
Irrota laite. Yksikössä saattaa olla useampia kuin yksi virtajohto. Irrota kaikki
virtajohdot ennen yksikön huoltamista, niin sähköiskun vaara pienenee.
Déclaration 1 :
Déconnecter l'appareil - Cette unité peut disposer de plusieurs cordons
d'alimentation. Déconnectez tous les cordons d'alimentation avant son entretien
pour réduire le risque d'électrocution.
Anweisung 1:
Gerät trennen - Diese Komponente verfügt möglicherweise über mehrere
Netzkabel. Trennen Sie alle Netzkabel bevor Sie die Komponente warten, um die
Gefahr eines elektrischen Schlags zu vermeiden.
D000140-001 D
B-1
Safety and Regulatory Compliance Information
Safety Information
Dichiarazione 1:
Scollegare il dispositivo - L'unità potrebbe avere più di un cavo di alimentazione.
Per ridurre il rischio di scosse elettriche, scollegare tutti i cavi di alimentazione
prima di intervenire sull'unità.
Erklæring 1:
Frakobling av enheten - denne enheten kan ha mer enn én strømledning. For å
redusere faren for elektrisk sjokk, må alle strømkablene trekkes ut før enheten
vedlikeholdes.
Declaração 1:
Desligar dispositivo - Esta unidade pode ter mais de um cabo de alimentação.
Para reduzir o risco de choque eléctrico, desligue todos os cabos de alimentação
antes de fazer a manutenção da unidade.
Declaración 1:
Desconexión de dispositivo - Esta unidad puede tener más de un cable de
alimentación eléctrica. Para reducir el riesgo de electrocución, desconecte todos
los cables antes de realizar cualquier servicio técnico en la unidad.
Uttalande 1:
Koppla bort enhet. Den här enheten kan ha mer än en strömsladd. Reducera
risken för elektrisk stöt genom att koppla bort alla strömsladdar innan enheten
underhålls.
Kijelentés 1:
Szüntesse meg az eszköz tápellátását – Ez az egység egynél több tápvezetékkel
rendelkezhet. Az áramütés kockázatának csökkentése érdekében minden
tápvezetéket húzzon ki az egység szervizelése elott.
Инструкция 1:
Отключите устройство – В данном устройстве может быть более одного
сетевого шнура. Во избежание поражения электрическим током отсоедините
все сетевые шнуры до проведения технического обслуживания устройства.
声明 1:
断开装置 - 此装置可能有一个以上电源电缆。为了减少电击风险,请在维修该装置
前断开所有电源电缆。
ステートメント 1:
デバイスを外してください - このユニットには複数の電源ユニットが接続され
ている可能性があります。感電のリスクを軽減するため、ユニットを修理する前
にすべての電源コードを外してください。
B-2
D000140-001 D
Safety and Regulatory Compliance Information
Safety Information
Statement 2:
Chassis Lifting - Use safe practices when lifting.
NOTE:
Use a team of people appropriate to the weight of each specified product
and in conjunction with applicable guidelines. Whenever possible, use a
mechanical lift.
Verklaring 2:
Chassis optillen - Volg de veiligheidsinstructies bij het optillen.
ANMERKUNG: Gebruik genoeg mensen voor het gewicht van elk gespecificeerd
product en hanteer de toepasselijke richtlijnen. Gebruik waar
mogelijk een mechanisch tilapparaat.
Varoitus 2:
Kotelon nostaminen. Noudata nostaessasi turvaohjeita.
HUOMAUTUS: Varaa nostamista varten laitteen painoon nähden sopiva ja
sovellettavien ohjeiden mukainen määrä henkilöitä. Käytä
mekaanista nosturia aina, kun se on mahdollista.
Déclaration 2 :
Soulever le châssis - Employez des mesures de sécurité pour soulever.
REMARQUE :
Faites appel au nombre de personnes approprié en fonction du
poids de chaque produit spécifique et en conjonction avec les
directives applicables. Utilisez un relevage mécanique, si possible.
Anweisung 2:
Anheben des Gehäuses - Lassen Sie Sicherheit beim Anheben des Gehäuses
walten.
ANMERKUNG: Setzen Sie jeweils dem Gewicht jedes angegebenen Produkts und
den Richtlinien entsprechend genügend Leute ein. Verwenden Sie,
wenn möglich, einen mechanischen Aufzug.
Dichiarazione 2:
Sollevamento del telaio - Durante il sollevamento, seguire le procedure di
sicurezza.
D000140-001 D
B-3
Safety and Regulatory Compliance Information
Safety Information
NOTA:
utilizzare un gruppo di persone adeguato al peso di ogni prodotto
specifico e insieme alle indicazioni applicabili. Se possibile, usare
un sollevatore meccanico.
Erklæring 2:
Løfting av kabinettet - utvis varsomhet ved løfting.
MERK:
Bruk flere personer til bæring, avhengig av vekten til hvert enkelt
produkt og i samsvar med gjeldende retningslinjer. Bruk mekaniske
løftemekanismer når mulig.
Declaração 2:
Levantar o chassi - Utilize práticas seguras ao levantar o chassi.
AVISO:
Utilize um grupo de pessoas adequado ao peso de cada produto
especificado, em conjunto com as directivas aplicáveis. Sempre
que possível, utilize um dispositivo mecânico de levantamento.
Declaración 2:
Elevación del chasis - Observe las prácticas de seguridad cuando quiera elevar el
chasis.
NOTA:
utilice un grupo de gente apropiado al peso de cada producto
especificado junto con las pautas que correspondan. Siempre que
sea posible, utilice un elevador mecánico.
Uttalande 2:
Lyftning av chassi. Iakttag säkerhetsanvisningar vid lyft.
OBS!
Använd ett team personer lämpade för vikten på varje specificerad
produkt och i samband med gällande riktlinjer. Använd en
mekanisk lyftanordning närhelst det är möjligt.
Kijelentés 2:
A burkolat emelése – Biztonságos eljárásokat alkalmazzon az emelés során.
MEGJEGYZÉS: Az egyes termékek súlyának megfelelo fobol álló csoportot
alkalmazzon, a vonatkozó irányelvek betartása mellett. Lehetoség
szerint mindig használjon mechanikus emeloszerkezetet.
Инструкция 2:
Подъем корпуса – Соблюдайте технику безопасности при подъеме.
ПРИМЕЧАНИЕ:Подъем каждого конкретного устройства исходя из его веса
должен осуществляться несколькими лицами и в соответствии
с надлежащим инструкциям. Везде, где это возможно, следует
применять механические грузоподъемные устройства.
B-4
D000140-001 D
Safety and Regulatory Compliance Information
Safety Information
声明 2:
提起机箱 - 提起机箱时请采取安全措施。
注:
请按照每个具体产品的重量来使用一定的人数,并遵照适当的说
明。可能的话,使用机械起重器。
ステートメント 2:
シャーシの持ち上げ - シャーシを持ち上げる際は安全に配慮してください。
メモ :
D000140-001 D
各製品の重量に見合った人数で、適切なガイドラインに従って
持ち上げてください。可能な場合は、リフト機を使用してくだ
さい。
B-5
Safety and Regulatory Compliance Information
Safety Information
Statement 3:
Energy Hazard - To reduce risk of electric shock, keep hands and fingers out of
the power supply bays and backplane areas.
Verklaring 3:
Stroomgevaar - Reduceer het risico op een elektrische schok door handen en
vingers weg te houden bij de voedingscompartimenten en de gebieden rond de
centrale printplaat.
Varoitus 3:
Sähköiskun vaara. Voit vähentää sähköiskuille altistumista, kun vältät
koskettamasta virtalähdepaikkoja ja keskuspiirilevyä.
Déclaration 3 :
Danger électrique - Pour réduire le risque d'électrocution, gardez vos mains hors
des baies d'alimentation et des zones destinées aux cartes de circuits imprimés.
Anweisung 3:
Gefahr vor elektrischem Schock - Um der Gefahr vor elektrischem Schock
vorzubeugen, halten Sie Hände und Finger den Netzteilschächten und der
Rückwand fern.
Dichiarazione 3:
Pericolo di scosse - Per ridurre il rischio di scosse elettriche, allontanare le mani e
le dita dagli alloggiamenti degli alimentatori e dalle aree della piastra base.
Erklæring 3:
Strømfare - hold fingre og hender unna strømforsyningsrom og kretskort for å
unngå elektrisk sjokk.
Declaração 3:
Risco de choque eléctrico - Para reduzir o risco de choque eléctrico, mantenha as
mãos e os dedos fora dos compartimentos da fonte de alimentação e das áreas
de backplane.
Declaración 3:
Peligro de energía - Para reducir el riesgo de electrocución, mantenga las manos
y los dedos alejados de los compartimentos de la fuente de alimentación eléctrica
y del circuito impreso central.
B-6
D000140-001 D
Safety and Regulatory Compliance Information
Safety Information
Uttalande 3:
Risk för elektrisk stöt. Reducera risken för elektrisk stöt genom att hålla händer
och fingrar borta från strömförsörjningsfack och bakpanelsområden.
Kijelentés 3:
Áramütés veszélye – Az áramütés kockázatának csökkentése érdekében kezeit
és ujjait tartsa távol a tápcsatlakozóktól és a hátsó területektol.
Инструкция 3:
Опасное напряжение – Во избежание поражения электрическим током, не
прикасайтесь к клеммам электропитания и к центральнoй электроннoй
плате.
声明 3:
电能危害 - 为了减少电击风险,手和指应远离电源架和印刷电路板区域。
ステートメント 3:
エネルギーの危険 - 感電のリスクを軽減するため、電源装置ベイおよびバック
プレーン周辺に手や指を近づけないでください。
D000140-001 D
B-7
Safety and Regulatory Compliance Information
Safety Information
Statement 4:
Laser Radiation - certain optical products may emit laser radiation. Removing
covers could result in exposure to hazardous laser radiation. Radiation may be
emitted from connectors or fiber optic cables.
Verklaring 4:
Laserstraling - bepaalde optische producten kunnen laserstraling verspreiden.
Het verwijderen van dekplaten kan resulteren in blootstelling aan schadelijke
laserstraling. Straling kan worden afgegeven door connectoren of
glasvezelkabels.
Varoitus 4:
Lasersäteily. Jotkut optiset laitteet saattavat päästää lasersäteilyä. Niiden
suojusten poistaminen saattaa altistaa vaaralliselle lasersäteilylle. Säteily voi tulla
liittimistä tai optisista kuitukaapeleista.
Déclaration 4 :
Rayonnement laser - Certains produits optiques peuvent produire un
rayonnement laser. Le retrait de capots peut engendrer une exposition à un
rayonnement laser dangereux. Ce rayonnement peut provenir des connecteurs
ou des câbles en fibre optique.
Anweisung 4:
Laserstrahlung - manche optischen Produkte geben Laserstrahlung ab. Beim
Entfernen der Abdeckungen können Sie möglicherweise gefährlicher
Laserstrahlung ausgesetzt werden. Laserstrahlung kann von Anschlüssen oder
Faseroptikkabeln abgegeben werden.
Dichiarazione 4:
Radiazione laser - Alcuni prodotti ottici potrebbero emettere la radiazione laser.
La rimozione delle coperture potrebbe causare l'esposizione alla radiazione laser
pericolosa. I connettori o i cavi in fibra ottica potrebbero emettere radiazioni.
Erklæring 4:
Laserstråling - visse optiske produkter kan gi fra seg laserstråling. Dersom
dekslene tas av, kan dette medføre utsettelse for farlig laserstråling. Strålingen
kan komme fra kontakter eller fiberoptiske kabler.
B-8
D000140-001 D
Safety and Regulatory Compliance Information
Safety Information
Declaração 4:
Radiação laser - Certos produtos ópticos podem emitir radiação laser. A remoção
de tampas pode resultar na exposição a níveis perigosos de radiação laser. A
radiação pode ser emitida de conectores ou de cabos de fibra óptica.
Declaración 4:
Radiación de láser - Ciertos productos ópticos pueden emitir radiación de láser.
Quitar las cubiertas podría resultar en la exposición peligrosa a radiación de láser.
La radiación se puede emitir de conectores o cables de fibra óptica.
Uttalande 4:
Laserstrålning. Vissa optiska produkter kan utsända laserstrålning. Borttagning av
skydd kan resultera i exponering för riskfylld laserstrålning. Strålning kan
utsändas från kopplingsdetaljer eller fiberoptiska kablar.
Kijelentés 4:
Lézersugárzás – Bizonyos optikai termékek lézersugárzást bocsátanak ki. A
burkolatok eltávolításával veszélyes lézersugárzásnak tehetik ki magukat.
Sugárzást csatlakozók vagy üvegszálas optikai kábelek bocsáthatnak ki.
Инструкция 4:
Лазерное излучение! – некоторые оптические устройства являются
источником лазерного излучения. При снятии крышки существует опасность
воздействия лазерного излучения на персонал. Лазерное излучение может
испускаться соединительными гнездами волоконно-оптических кабелей.
声明 4:
激光辐射 - 某些光学产品会发出激光辐射。移开盖板时会使人暴露于有害激光辐
射。连接器或光纤电缆都可能发出辐射。
ステートメント 4:
レーザー光線 - 特定の光学製品からレーザー光線が放射される可能性がありま
す。カバーを取り除くと、危険なレーザー光線を被爆する場合があります。光線
はコネクタまたは光ファイバーケーブルから放射されることがあります。
D000140-001 D
B-9
Safety and Regulatory Compliance Information
Safety Information
Statement 5:
No User Serviceable parts - Hazardous energy levels may be present inside
power supplies and circuit card modules. Do not remove covers.
Verklaring 5:
Onderdelen die niet door de gebruiker mogen worden onderhouden - Er kunnen
gevaarlijke energieniveaus aanwezig zijn binnen voedingen en printplaten.
Verwijder in geen geval dekplaten.
Varoitus 5:
Ei osia, jotka käyttäjä voisi vaihtaa. Virtalähteiden ja piirikorttimoduulien sisällä
saattaa olla vaarallisen suuri virta tai jännite. Älä poista niiden suojuksia.
Déclaration 5 :
Pièces non entretenues par l'utilisateur - Des niveaux d'électricité dangereux
peuvent résider à l'intérieur des sources d'alimentation et des modules de carte
de circuits imprimés. Ne retirez pas les capots.
Anweisung 5:
Wartung nur durch Fachmann möglich - Gefährlich hohe Stromstärken sind in
Netzteilen und in den Modulen der Busleiterplatte vorhanden. Entfernen Sie die
Abdeckungen nicht.
Dichiarazione 5:
Non sono presenti componenti riparabili dall'utente - Livelli pericolosi di energia
potrebbero essere presenti all'interno degli alimentatori e dei moduli delle schede
dei circuiti. Non rimuovere le coperture.
Erklæring 5:
Ingen deler som kan vedlikeholdes av brukeren - farlig strømmengde kan finnes
inni strømforsynings- og kretskortmoduler. Fjern ikke dekslene.
Declaração 5:
Não há peças a serem consertadas pelo utilizador - Níveis perigosos de energia
podem estar presentes em fontes de alimentação e em módulos de placas de
circuito. Não remova as tampas.
Declaración 5:
No hay piezas técnicas - Niveles peligrosos de energía pueden hacerse
presentes en las fuentes de alimentación eléctrica. No quite las cubiertas.
B-10
D000140-001 D
Safety and Regulatory Compliance Information
Safety Information
Uttalande 5:
Inga delar kan underhållas av användaren. Farliga energinivåer kan finnas i
strömförsörjningsenheter kretskortmoduler. Ta inte bort skydd.
Kijelentés 5:
A berendezés nem tartalmaz felhasználó által javítható alkatrészeket – Veszélyes
energiaszint lehet a tápegységeken és az áramköri kártyamodulokon belül. Ne
távolítsa el a burkolatokat.
Инструкция 5:
Устройство не содержит деталей, предназначенных для обслуживания
пользователем – Блоки питания и электрические платы устройства являются
источником опасного электрического напряжения. Снимать крышки
запрещено.
声明 5:
禁止用户维修部件 - 电源和电路卡模块内部可能存在一定水平的有害能。切勿移除
盖板。
ステートメント 5:
ユーザー修理可能部品なし - 電源装置および回路カードモジュール内のエネル
ギーが危険なレベルに達している場合があります。カバーを外さないでくださ
い。
D000140-001 D
B-11
Safety and Regulatory Compliance Information
Safety Information
Statement 6:
Equipment Installation - Only qualified personnel should be allowed to install,
remove or replace chassis or modules.
Verklaring 6:
Installatie apparatuur - Voor het installeren, verwijderen of vervangen van chassis
of modules mag alleen gekwalificeerd personeel worden gebruikt.
Varoitus 6:
Laitteiston asentaminen. Vain pätevä asentaja saa asentaa, poistaa ja vaihtaa
koteloita tai moduuleja.
Déclaration 6 :
Installation de l'équipement - Seul un personnel qualifié est autorisé à installer,
retirer ou remplacer des châssis ou modules.
Anweisung 6:
Geräteinstallation - Die Installation, Entfernung oder Erneuerung von Gehäuse
und Modulen sollte nur durch Fachpersonal erfolgen.
Dichiarazione 6:
Installazione dell'apparecchiatura - Solo il personale qualificato è autorizzato ad
installare, rimuovere o ricollocare il telaio o i moduli.
Erklæring 6:
Utstyrsinstallasjon - kun kvalifisert personell kan installere, fjerne eller skifte ut
kabinetter eller moduler.
Declaração 6:
Instalação do equipamento - A instalação, troca ou remoção de chassis ou
módulos só deve ser feita por técnicos qualificados.
Declaración 6:
Instalación del equipo - Solamente se permite personal cualificado para realizar
la instalación, quitar o sustituir módulos o chasis.
Uttalande 6:
Installation av utrustning. Enbart kvalificerad personal får installera, ta bort eller
byta ut chassin eller moduler.
B-12
D000140-001 D
Safety and Regulatory Compliance Information
Safety Information
Kijelentés 6:
Berendezés telepítése – Kizárólag szakképzett személyzet számára
megengedett a burkolat vagy a modulok telepítése, eltávolítása vagy cseréje.
Инструкция 6:
Установка оборудования – Установка, удаление и замена корпуса или
модулей устройства должна производиться только квалифицированным
техническим персоналом.
声明 6:
设备安装 - 只有有资格的技术人员才允许安装、卸下或装回机箱或模块。
ステートメント 6:
装置の取り付け - シャーシまたはモジュールの取り付け、取り外しまたは取替
えは、有資格者のみが行うようにしてください。
D000140-001 D
B-13
Safety and Regulatory Compliance Information
Safety Information
Statement 7:
Adding or Replacing Modules - These modules are intended only for installation in
QLogic 12000 base units. Always install blanks when removing an active module.
They prevent exposure to energy hazards inside the unit, contain EMI, and
maintain cooling air balance in the chassis.
Verklaring 7:
Toevoegen of vervangen van modules - deze modules zijn alleen bedoeld voor
installatie in basiseenheden uit de QLogic 12000-reeks. Installeer altijd
plaatshouders wanneer u een actieve module verwijdert. Deze voorkomen
blootstelling aan energierisico's binnen de eenheid, bevatten EMI en handhaven
de koelluchtbalans in het chassis.
Varoitus 7:
Moduulien lisääminen ja vaihtaminen. Moduulit on tarkoitettu asennettavaksi vain
QLogic 12000 -sarjan perusyksikköihin. Kun olet poistanut aktiivisen moduulin,
muista aina asentaa tyhjä kappale sen paikalle. Ne estävät sähköiskuille
altistumista yksikön sisällä, hillitsevät sähkömagneettisia häiriöitä (EMI) ja pitävät
yllä jäähdytysilman tasaista jakautumista koteloon.
Déclaration 7 :
Ajouter ou remplacer des modules - Ces modules sont conçus exclusivement
pour une installation avec des unités de base QLogic 12000 Series. Installez
toujours des caches de protection lors du retrait d'un module actif. Ils protègent
contre les dangers électriques à l'intérieur de l'unité, limitent l'interférence
électromagnétique et maintiennent un volume d’air refroidissant approprié au sein
du châssis.
Anweisung 7:
Hinzufügen oder Austauschen von Modulen - Diese Module sind für die
Installation in Grundeinheiten der QLogic 12000 Serie vorgesehen. Installieren
Sie stets leere Module, wenn Sie ein aktives Modul entfernen. Diese verhindern,
dass Stromgefahr im Innern der Einheit entsteht, enthalten Störstrahlung und
sorgen für den Kühlungsausgleich im Gehäuse.
Dichiarazione 7:
Aggiunta o sostituzione dei moduli - I moduli sono concepiti solo per l'installazione
nelle unità di base QLogic 12000 Serie. Quando si rimuove un modulo attivo,
installare sempre le protezioni, poiché impediscono l'esposizione ai pericoli di
scosse all'interno dell'unità, contengono le IEM e mantengono un equilibrio
dell'aria di raffreddamento nel telaio.
B-14
D000140-001 D
Safety and Regulatory Compliance Information
Safety Information
Erklæring 7:
Tillegging eller utskifting av moduler - disse modulene skal kun installeres i
baseenhetene på QLogic 12000-serien. Installer alltid tomme enheter når en aktiv
modul fjernes. De forhindrer utsettelse for strømfare inni enheten, inneholder EMI
og opprettholder kjølebalansen i kabinettet.
Declaração 7:
Adição ou troca de módulos - Estes módulos foram projectados para serem
instalados apenas nas unidades de base QLogic 12000 série. Instale sempre
módulos de preenchimento ("blanks") ao remover módulos activos. Eles
diminuem os riscos de choque eléctrico no interior da unidade, contêm
dispositivos de protecção contra interferência eletromagnética e mantêm o
equilíbrio de resfriamento por ar no interior do chassi.
Declaración 7:
Agregar o sustituir módulos - Estos módulos solamente se pueden instalar en
unidades de base de la serie QLogic 12000. Siempre instale protectores al retirar
un módulo activo. Los protectores previenen la exposición a peligros de energía
dentro de la unidad, contienen EMI y mantienen el balance de enfriamiento de
aire en el chasis.
Uttalande 7:
Lägga till eller byta ut moduler. De här modulerna är enbart avsedda för
installation i QLogic 12000-seriens basenheter. Installera alltid tomenheter vid
borttagning av en aktiv modul. De förhindrar exponering för energirisker på
enhetens insida, hindrar EMI och upprätthåller kylluftbalansen i chassin.
Kijelentés 7:
Modulok hozzáadása vagy cseréje – Ezek a modulok kizárólag QLogic 12000-es
sorozatú bázisegységekbe építhetoek be. Aktív modul cseréjekor mindig
szereljen be üres helyeket. Ezek megakadályozzák az egységen belüli
energiaveszélyek kialakulását, tartalmaznak EMI-t, és fenntartják a hutolevego
egyensúlyát a borításon belül.
Инструкция 7:
Установка и замена модулей – Модули предназначены только для установки
внутрь базовых блоков QLogic серии 12000. После замены действующих
модулей следует всегда устанавливать заглушки с крышками. Это
обеспечивает защиту от опасного напряжения, электромагнитного излучения
и надлежащий тепловой баланс внутри корпуса.
声明 7:
添加或装回模块 - 这些模块仅用于安装在 QLogic 12000 Series 基座装置。请在移
除活动模块时安装空白的。它们能预防装置内部的有害能的暴露,包含 EMI, 并在
机箱内保持冷却空气平衡。
D000140-001 D
B-15
Safety and Regulatory Compliance Information
Safety Information
ステートメント 7:
モジュールの追加または取替え - これらのモジュールは QLogic 12000 シリーズ
MPFD ベースユニットへの取り付け専用です。アクティブなモジュールを取り除
く際は、常にダミーを取り付けてください。これはユニット内の危険なエネル
ギーの露出を防止し、EMI を阻止、およびシャーシ内の空冷バランスを維持しま
す。
B-16
D000140-001 D
Safety and Regulatory Compliance Information
Safety Information
D000140-001 D
B-17
Safety and Regulatory Compliance Information
Safety Information
Notes
B-18
D000140-001 D
C
Serial Port Pinouts
For those users making their own serial cables, follow the guidelines below.
Figure C-1 Serial Port Pinouts
D000140-001 D
C-1
Serial Port Pinouts
Figure C-1 represents the RJ-11 connector located on the QLogic 12200
and12300.
The only serial port signals required are: Tx, Rx and Ground. All other serial
port signals are NOT used.
Please see Table C-1 for a list of RJ45 (on Digi) to RJ11 cross-references. The
cable should connect the three RJ45 signals (on the Digi) to the RJ11 connector.
The signals for the T3 card located inside the switch and spine are included for
reference only.
„
Table C-1. Pinout Cross Reference
RJ45 (on Digi)
C-2
RJ11
T3 RJ45
(reference only)
P5-Rx
P5
P6-Tx
P6-Gnd
P4
P4-Gnd
P4-Tx
P3
P5-Rx
D000140-001 D
Serial Port Pinouts
D000140-001 D
C-3
Serial Port Pinouts
Notes
C-4
D000140-001 D
D
FRU Replacement
This section details replacement information for various QLogic 12000 field
replaceable units (FRUs). For replacement parts, contact QLogic or an approved
reseller.
NOTE:
If it is part of a standard operating procedure, add replacement identification
tags to both the rack and the FRU hardware to ensure that the warranty is
transferred to the replacement part(s).
NOTE:
If the FRU being replaced is in an active chassis (that is, hot swapping),
please replace the FRU within 2 minutes to maintain thermal integrity.
QLogic 12200
NOTE:
For an externally-managed 12200, refer to the Fast Fabric User Guide for
update information.
Chassis Replacement
FRU part number:
„
Standard chassis: 12200-BS01
„
Reversed airflow/AC power inlets: 12200-BS02
Removal Procedures
1.
Power down the switch by unplugging AC power.
2.
Remove all applicable IB, Ethernet and Serial cables. Set these aside for
reinstalling the replacement switch.
D000140-001 D
D-1
D–FRU Replacement
QLogic 12300
3.
Remove the switch from the rack. Keep all rail hardware installed in the rack.
4.
Remove the hat rails from the switch. Set these aside for for reinstalling the
replacement switch.
Replacement Procedures
1.
Install the hat rails to the switch.
2.
Rack mount the switch in the existing rails on the rack.
3.
Connect Ethernet and Serial cables (managed 12200 only).
4.
Connect AC power.
5.
If applicable, change the switch, gateway and subnet mask addresses to a
new network address.
6.
Cable all applicable IB ports.
QLogic 12300
Chassis Replacement
FRU part number:
„
Standard 36-port chassis: 12300-BS01
„
12300 18-port chassis: 12300-BS18
Removal Procedures
1.
Power down the switch by unplugging AC power.
2.
Remove all applicable IB, Ethernet and Serial cables. Set these aside for
reinstalling the replacement switch.
3.
Remove the switch from the rack. Keep all rail hardware installed in the rack.
4.
Remove the hat rails from the switch. Set these aside for for reinstalling the
replacement switch.
Replacement Procedures
D-2
1.
Install the hat rails to the switch.
2.
Rack mount the switch in the existing rails on the rack.
3.
Connect Ethernet and Serial cables.
4.
Connect AC power.
5.
Change the switch, gateway and subnet mask addresses to a new network
address.
6.
Cable all applicable IB ports.
D000140-001 D
D–FRU Replacement
QLogic 12300
Fan/Power Supply Replacement
FRU part number:12300-PS01
NOTE:
These fan/power supplies are to be used exclusively with the QLogic 12300
QDR InfiniBand switch and are not intended to be sold separately.
Removal Procedures
1.
Push the finger tab to the right.
2.
While holding the finger tab, pull the module handle to disengage the unit
from the switch.
Figure D-1 .12300 Fan/Power Module Removal
Replacement Procedures
1.
D000140-001 D
Hold the unit by the handle and slide into the applicable slot until the finger
tab clicks into place.
D-3
D–FRU Replacement
QLogic 12800 Series
QLogic 12800 Series
Fan Replacement
FRU part numbers:
„
Intake Fan: 12800-FITK
„
Exhaust Fan: 12800-FEXH
Removal Procedures
1.
While holding the handle, push the release latch to the right
Figure D-2 .12800 Fan Removal
D-4
2.
Pull the fan by the handle until disengaged from the chassis.
3.
Determine whether this is an intake or exhaust fan by checking the FRU
label or noting the location of the open notch.
D000140-001 D
D–FRU Replacement
QLogic 12800 Series
Figure D-3 .12800 Intake and Exhaust Fans
Replacement Procedures
1.
Slide the fan tray straight into the open slot until it engages with the
backplane connector.
2.
Make sure the fan is operating and the status LED is green.
D000140-001 D
D-5
D–FRU Replacement
QLogic 12800 Series
Power Supply Replacement
FRU part number:12800-PS01
NOTE:
These power supplies are to be used exclusively with the QLogic
12800-series QDR InfiniBand switches and are not intended to be sold
separately.
Removal Procedures
1.
Push the release latch to release the arm.
Figure D-4 .12800 Power Removal
2.
Carefully pull the supply until it is disengaged from the chassis.
Replacement Procedures
D-6
1.
Slide the power supply straight into the open slot until it engages with the
backplane connector.
2.
Make sure the supply is operating and the AC OK and DC OK LEDs are
green.
D000140-001 D
D–FRU Replacement
QLogic 12800 Series
Leaf Module Replacement
FRU part number:
„
18 Port Leaf: 12800-LF18
„
24 Port Leaf: 12800-LF24
Removal Procedures
NOTE:
If the leaf module is in one of the chassis management slots, the mechanical
release latch (MRL) must be moved in order to remove the leaf. To move the
MRL, loosen the thumbscrew attached to the the Serial, Ethernet, Chassis
EEPROM Board (SEEB) module, then slide the MRL to the left. This allows
enough clearance for leaf release arm.
Figure D-5 .MRL
D000140-001 D
D-7
D–FRU Replacement
QLogic 12800 Series
1.
Pull the release arms down until the leaf module disengages from the
backplane connector.
Figure D-6 .12800 Leaf Removal
2.
Carefully pull the module out of the chassis.
Replacement Procedures
D-8
1.
Slide the module straight into the open slot until it engages with the
backplane connector.
2.
Push the arm up until they lock in place.
3.
Make sure the module is operating and the Status LED is green.
D000140-001 D
D–FRU Replacement
QLogic 12800 Series
Spine Module Replacement
FRU part number:
„
Single Spine Module: 12800-SPSG01
„
Double Spine Module: 12800-SPDB01
Removal Procedures
1.
Pull the release arms out until the spine module disengages from the
backplane connector.
Figure D-7 .12800 Spine Removal
2.
Carefully pull the module out of the chassis.
Replacement Procedures
1.
Slide the module straight into the open slot until it engages with the
backplane connector.
2.
Push the arm up until they lock in place.
3.
Make sure the module is operating and the Status LED(s) is green.
D000140-001 D
D-9
D–FRU Replacement
QLogic 12800 Series
Management Module Replacement
FRU part number:12800-MM01
Removal Procedures
1.
Loosen the thumbscrew until it releases from the faceplate.
2.
Pull the release arms out until the management module disengages from the
backplane connector.
Figure D-8 .12800 Management Module Removal
3.
Carefully pull the module out of the chassis.
Replacement Procedures
1.
Slide the module straight into the open slot until it engages with the
backplane connector.
2.
Push the arm up until it locks in place.
3.
Tighten the thumbscrew.
4.
Make sure the module is operating and the Module Status, Chassis Status
and MRL Active LEDs are green.
NOTE:
The standard FRU replacement process for managment modules is one at
time. This allows the master module to move to a slave state, if necessary.
Never replace multiple management modules simultaneously.
D-10
D000140-001 D
Corporate Headquarters QLogic Corporation 26650 Aliso Viejo Parkway
Aliso Viejo, CA 92656 949.389.6000
www.qlogic.com
International Offices UK | Ireland | Germany | India | Japan | China | Hong Kong | Singapore | Taiwan
© 2010 QLogic Corporation. Specifications are subject to change without notice. All rights reserved worldwide. QLogic and the QLogic logo are
registered trademarks of QLogic Corporation. All other brand and product names are trademarks or registered trademarks of their respective
owners. Information supplied by QLogic Corporation is believed to be accurate and reliable. QLogic Corporation assumes no responsibility for
any errors in this brochure. QLogic Corporation reserves the right, without notice, to make changes in product design or specifications.