Directed Electronics Tablet DVD Player TD700 Operating instructions

LC-60LE450U
LC-60LE452U
IMPORTANT : Please read this operation manual before starting operating the equipment.
IMPORTANT : Veuillez lire ce mode demploi avant de commencer utilliser lappareil.
IMPORTANTE: Lea este manual de operación antes de comenzar a operar el equipo.
ENGLISH
LC-60LE450U
LC-60LE452U
LIQUID CRYSTAL TELEVISION
ENGLISH
OPERATION MANUAL
IMPORTANT:
To aid reporting in case of loss or theft, please
record the TV's model and serial numbers in the
space provided. The numbers are located at the
rear of the TV.
Model No.:
Serial No.:
IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
1
IMPORTANT INFORMATION
CAUTION: TO PREVENT ELECTRIC SHOCK,MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
WARNING: FCC Regulations state that any unauthorized changes or modifications to this
equipment not expressly approved by the manufacturer could void the users authority to operate
this equipment.
CAUTION:
This product satisfies FCC regulations when shielded cables and connectors a re used to connect
the unit to other equipment. To prevent electromagnetic interference with electric appliances such
as radios and televisions, use shielded cables and connectors for connections.
DECLARATION OF CONFORMITY:
SHARP LIQUID CRYSTAL TELEVISION, MODEL LC-60LE450U/LC-60LE452U This device
complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.RESPONSIBLE PARTY:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
TEL: 1-800-BE-SHARP
For Business Customers: URL http://www.sharpusa.com
INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits a re designed to p rovidereasonable protection
against harmful interfe rence in a residential installation. This equipment generates, uses and can
radiate radio f requency energy and, if not installed and used in acco rdance with the instructions,
may cause harmful interfe rence to radio communications. Howeve r, there is no guarantee
that interfe rence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by tu rning the equipment off
and on, the user is encouraged to try to cor rect the interfe rence by one or mo re of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
— Consult the dealer or an experienced radio/TV technician for help.
Note to CATV system installer: This reminder is provided to call the CATV system installer s
attention to Article 820 of the National Electrical Code that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.
TRADEMARKS
• The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI Licensing LLC in the United States and other
countries.
• Manufactured under license from Dolby Laboratories.Dolby and the double-D
symbol are trademarks of Dolby Laboratories.
2
3
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
• These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric
shock do not perform any servicing other than that contained in the operating instructions unless you are
qualified to do so.
• Outdoor Antenna Grounding — If an outside
antenna is connected to the television
equipment, be sure the antenna system is
grounded so as to provide some protection
against voltage surges and built-up static
charges.
Article 810 of the National Electrical Code,
ANSI/NFPA 70, provides information with
regard to proper grounding of the mast
and supporting structure, grounding of the
lead-in wire to an antenna discharge unit,
size of grounding conductors, location
of antenna-discharge unit, connection to
grounding electrodes, and requirements for
the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250)
NEC — NATIONAL ELECTRICAL CODE
• Warning statement indicating that Class II apparatus shall be connected to a mains socket outlet
with a protective earthing connection.
• Statement indicating that when the mains plug or appliance coupler shall remain readily operable.
• Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect
device shall remain readily operable.
• Water and Moisture — Do not use this product near water - for example, near a bath tub, wash
bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.
• Stand — Do not place the product on an unstable cart, stand, tripod or table. Placing the product
on an unstable base can cause the product to fall, resulting in serious personal injuries as well as
damage to the product. Use only a cart, stand, tripod, bracket or table recommended by the
manufacturer or sold with the product. When mounting the product on a wall, be sure to follow
the manufacturer’s instructions. Use only the mounting hardware recommended by the
manufacturer.
• Selecting the location — Select a place with no direct sunlight and good ventilation.
• Ventilation — The vents and other openings in the cabinet are designed for ventilation. Do not
cover or block these vents and openings since insufficient ventilation can cause overheating and/
or shorten the life of the product. Do not place the product on a bed, sofa, rug or other similar
surface, since they can block ventilation openings. This product is not designed for built-in
installation; do not place the product in an enclosed place such as a bookcase or rack, unless
proper ventilation is provided or the manufacturer’s instructions are followed.
• The Liquid Crystal panel used in this product is made of glass. Therefore, it can break when the
product is dropped or applied with impact. Be careful not to be injured by broken glass pieces
in case the panel breaks.
4
IMPORTANT SAFETY INSTRUCTIONS
• Heat — The product should be situated away from heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers) that produce heat.
• The Liquid Crystal panel is a very high technology product with 2,073,600 pixels (LC-60LE450U、
LC-60LE452U). Giving you fine picture details. Occasionally, a few non-active pixels may appear
on the screen as a fixed point of blue, green or red. Please note that this does not affect the
performance of your product.
• Lightning — For added protection for this television equipment during a lightning storm, or when
it is left unattended and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna. This will prevent damage to the equipment due to lightning and
power-line surges.
• Power Lines — An outside antenna system should not be located in the vicinity of overhead
power lines or other electric light or power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact with them might be fatal.
• To prevent fire, never place any type of candle or flames on the top or near the TV set.
• To prevent fire or shock hazard, do not place the AC cord under the TV set or other heavy items.
• Do not display a still picture for a long time, as this could cause an afterimage to remain.
• To prevent fire or shock hazard, do not expose this product to dripping or
splashing.
No objects filled with liquids, such as vases, should be placed on the product.
• Do not insert foreign objects into the product. Inserting objects in the air
vents or other openings may result in fire or electric shock. Exercise special
caution when using the product around children.
Precautions when transporting the TV
• When transporting the TV, never carry it by holding or otherwise putting pressure onto the display.
Be sure to always carry the TV by two people holding it with two hands — one hand on each side
of the TV.
Caring for the Cabinet
• Use a soft cloth (cotton, flannel, etc.) and gently wipe the surface of the cabinet.
• Using a chemical cloth (wet/dry sheet type cloth, etc.) may deform the components of the main
unit cabinet or cause cracking.
• Wiping with a hard cloth or using strong force may scratch the surface of the cabinet.
• If the cabinet is very dirty, wipe with a soft cloth (cotton, flannel, etc.) soaked in neutral detergent
diluted with water and thoroughly wrung out, and then wipe with a soft dry cloth.
• The cabinet is primarily made of plastic. Avoid using benzene, thinner, and other solvents, as
these may deform the cabinet and cause the paint to peel off.
• Do not apply insecticides or other volatile liquids.
Also, do not allow the cabinet to remain in contact with rubber or vinyl products for a long period
of time. Plasticizers inside the plastic may cause the cabinet to deform and cause the paint to
peel off.
Caring for the Liquid Crystal panel
• Turn off the main power and unplug the AC cord from the wall outlet before handling.
• Gently wipe the surface of the display panel with a soft cloth (cotton, flannel, etc.).
To protect the display panel, do not use a dirty cloth, liquid cleaners,
or a chemical cloth (wet/ dry sheet type cloth, etc.). This may damage
the surface of the display panel.
• Wiping with a hard cloth or using strong force may scratch the surface
of the display panel.
• Use a soft damp cloth to gently wipe the display panel when it is really
dirty. (It may scratch the surface of the display panel when wiped strongly.)
• If the display panel is dusty, use an anti-static brush, which is commercially available, to clean it.
• To avoid scratching the frame or screen, please use a soft, lint free cloth for cleaning. Approved
cleaning cloths are available directly from Sharp in single (00Z-LCD-CLOTH) or triple (00Z-LCDCLOTH-3) packs.
Call 1-800-BE-SHARP for ordering, or VISIT http://www.sharpusa.com/SharpDirect.
5
IMPORTANT SAFETY INSTRUCTIONS
CHILD SAFETY
It Makes A Di fference How and Where You Use Your Flat Panel Display
Congratulations on your purchase! As you enjoy your new product, please keep these safety
tips in mind:
THE ISSUE
The home theater entertainment experience is a growing trend and larger
flat panel displays are popular purchases. However, flat panel displays are
not always supported on the proper stands or installed according to the
manufacturer’s recommendations.
Flat panel displays that are inappropriately situated on dressers, bookcases,
shelves, desks, speakers, chests or carts may fall over and cause injury.
THIS MANUFACTURER CARES!
The consumer electronics industry is committed to making home
entertainment enjoyable and safe.
TUNE INTO SAFETY
One size does NOT fit all. Follow the manufacturer’s recommendations for
the safe installation and use of your flat panel display.
Carefully read and understand all enclosed instructions for proper use of this
product.
Don’t allow children to climb on or play with furniture and television sets.
Don’t place flat panel displays on furniture that can easily be used as steps,
such as a chest of drawers.
Remember that children can become excited while watching a program,
especially on a “larger than life” flat panel display. Care should be taken
to place or install the display where it cannot be pushed, pulled over, or
knocked down.
Care should be taken to route all cords and cables connected to the flat
panel display so that they cannot be pulled or grabbed by curious children.
WALL MOUNTING: IF YOU DECIDE TO WALL MOUNT YOUR FLAT PANEL DISPLAY,
ALWAYS:
Follow all instructions supplied by the display and wall mount manufacturers.
If you have any doubts about your ability to safely install your flat panel display, contact your retailer
about professional installation.
Make sure that the wall where you are mounting the display is appropriate. Some wall mounts are not
designed to be mounted to walls with steel studs or old cinder block construction. If you are unsure,
contact a professional installer.
A minimum of two people are required for installation. Flat panel displays can be heavy.
Note: CEA is the preeminent trade association promoting growth in
the $161 billion U.S. consumer electronics industry. More than 2,200
companies enjoy the benefits of CEA membership, including legislative
advocacy, market research, technical training and education, industry
promotion and the fostering of business and strategic relationships.
6
QUICK REFERENCE
Supplied Accessories
Make sure the following accessories are provided with the product.
X6
x4
Remote control unit “AAA” size battery Stand base(X1) Stand Support(X1) Operation manual Connection guide
with Screws
with Screws
( X 1)
( X 1)
( X 2)
( X 1)
Page 7
Page 7
Page 11
Page 9
• Always use the AC cord supplied with the TV.
• The illustrations above are for explanation purposes and may vary slightly from the actual
accessories.
Attaching/Detaching the Stand
• Before attaching (or detaching) the stand, unplug the AC cord.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it
from being damaged.
CAUTION
Attach the stand in the correct direction.
Be sure to follow the instructions. Incorrect installation of the stand may result in the TV
falling over.
1. Put the TV face down on a safe surface that is covered by a soft and smooth cloth. ( Show in diagram 1)
2. Fix the TV stand support to the stand base, fasten the screws by using a cross-head screwdriver
(Not supplied).( Show in diagram 2)
3. Fix the TV stand base to the TV, fasten the screws by using a cross-head screwdriver (Not supplied).
( Show in diagram 3)
(4 pc s screws)
(6 pc s screws)
CAUTION
Do not push too hard or put excessive pressure to the stand neck to avoid the
damages when you turn the TV for the most comfortable viewing angle.
To detach the stand, perform the steps in reverse order.
3
15 / 4 (400mm) A
VESA screw hole specs(A-B)
in millimeters
Standard screw
Quantity
3
3
Use the four screws provided to fix the TV onto a wall
mounting bracket (not included) via the four VESA
standard holes on the back of the television.
15 / 4 (400mm) B
Wall Mount
3
15 /4 -15 /4
(400-400)
M6 (1.0 pitch screw)
4
400x400mm VESA mount
7
QUICK REFERENCE
Quick Installation Tips
1. Attach your antenna to the back of the
television. (See page 10.)
2. Connect the AC plug for the television into the
AC outlet.
POWER indicator
4. Insert the batteries into the remote control
unit. (See page 11.)
Place the TV close to the AC outlet, and keep
the power plug within reach.
TO PREVENT RISK OF ELECTRIC SHOCK,
DO NOT TOUCH UN-INSULATED PARTS
OF ANY CABLES WITH THE AC CORD
CONNECTED.
3. When turning on the TV for the first time,
press POWER on the television.
/
8
Speakers cannot be detached from the TV.
The TV angle cannot be adjusted.
QUICK REFERENCE
Using the Remote Control Unit
Use the remote control unit by pointing it towards the remote control sensor on the TV. Objects
between the remote control unit and the remote control sensor may prevent proper operation.
¡ Cautions regarding the remote control
unit
• Do not expose the remote control unit to
shock. In addition, do not expose the remote
control unit to liquids, and do not place in an
area with high humidity.
• Do not install or place the remote control unit
under direct sunlight. The heat may cause
deformation of the remote control unit.
• The remote control unit may not work
properly if the remote control sensor on the
TV is under direct sunlight or strong lighting.
In such cases, change the angle of the
lighting or the TV, or operate the remote
control unit closer to the remote control
sensor.
IMPORTANT:
If the POWER indicator light on the television still does not turn off, press POWER on the remote control to turn
the power on.
IMPORTANT:
IF THE UNIT DOES NOT POWER ON - UNPLUG THE TELEVISION FROM THE OUTLET AND REPEAT THE
INSTALLATION STEPS.
IF YOU STILL ENCOUNTER NO POWER, PLEASE CONTACT US AT 1-800-BE-SHARP.
9
Preparation
Antennas
To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types
of connections that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial
cable with an F-type connector, plug it into the antenna terminal at the rear of the TV set.
1. A 75-ohm system is generally a round cable
with F-type connector that can easily be
attached to a terminal without tools
(Commercially available).
2. A 300-ohm system is a flat “twin-lead” cable
that can be attached to a 75-ohm terminal
through a 300/75-ohm adapter (Commercially
available).
F-type connector
75-ohm coaxial cable
(round)
300-ohm twin-lead cable (flat)
When connecting the RF cable to the TV set, do
not tighten F-type connector with tools. If tools
are used, it may cause damage to your TV set.
(The breaking of internal circuit, etc.)
F-type connector
75-ohm coaxial cable
Connecting Antenna
Connect the antenna cable to the TV using one of the methods in the illustration as
shown ( 1 , 2 , 3 or 4 ).
1 Cable without a CATV converter
Home Antenna
terminal (75-ohm)
Cable TV lead-In
Coaxial cable
(commercially available)
2 VHF/UHF antenna
Home Antenna
terminal (75-ohm)
75-ohm coaxial cable (round)
Coaxial cable
(commercially available)
3 Combination VHF/UHF antenna
75-ohm coaxial cable (round)
ANT./CABLE
or
300-ohm twin-lead cable (at)
300/75-ohm adapter
(commercially available)
4 Separate VHF/UHF antenna
VHF
UHF
ANTENNA ANTENNA
300-ohm
twin-lead cable
IN
300-ohm twin-lead cable
or
10
75-ohm coaxial cable
OUT
Combiner
(commercially available)
To TV antenna terminal
Preparation
Installing Batteries in the Remote Control Unit
If the remote control fails to operate TV functions, replace the batteries in the remote control unit.
1 Open the battery cover.
3 Close the battery cover.
2 Insert two “AAA” size batteries (supplied
with the product).
Place the batteries with their terminals
corresponding to the ( ) and ( )
indications in the battery compartment.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the
instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new
batteries or cause chemical leakage in old batteries.
• Remove batteries as soon as they are worn out. Chemicals that leak from batteries come in
contact with skin can cause a rash. If you find any chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage
conditions.
• If you will not be using the remote control unit for an extended period of time, remove batteries
from it.
• The batteries (batteries installed) shall not be exposed to excessive heat such as sunshine, fire or
the like.
11
Contents
IMPORTANT INFORMATION ...................................................................................... 1
TRADEMARKS ............................................................................................................. 2
IMPORTANT SAFETY INSTRUCTIONS ...................................................................... 3
QUICK REFERENCE.................................................................................................... 7
Supplied Accessories................................................................................................... 7
Attaching/Detaching the Stand...................................................................................... 7
Quick Installation Tips.................................................................................................. 8
Using the Remote Control Unit...................................................................................... 9
Antennas..................................................................................................................10
Connecting Antenna Cable..........................................................................................10
Installing Batteries in the Remote Control Unit
................................................................ 11
Contents ..................................................................................................................... 12
Part Names ................................................................................................................ 13
TV (Front)................................................................................................................. 13
TV (Side/Rear)...........................................................................................................13
Introduction to Connections ..................................................................................... 14
Experiencing HD Images.............................................................................................14
Types of Connection..................................................................................................14
Displaying an External Equipment Image Display
.............................................................14
Connecting to External Equipment ..........................................................................15
Connecting a Blu-ray Disc/DVD Player or HD
Cable/Satellite Set-top Box .........................................................................................15
Connecting a Game Console,VCR,Camcorder
or Cable/Satellite Set-top Box..................................................................................... 16
Connecting an Audio Amplifier......................................................................................17
Connecting an AV Amplifier .........................................................................................17
Connecting a PC....................................................................................................... 18
Watching TV............................................................................................................... 19
Turning On/Off the Power........................................................................................... 19
Setup Wizard ........................................................................................................... 19
Direct Button Operation ............................................................................................ 21
On-Screen Display Menu .......................................................................................... 25
On-Screen Display Menu Operation............................................................................. 25
Menu Operation Button............................................................................................. 26
Picture Setting ......................................................................................................... 26
Audio Setting .......................................................................................................... 27
Time Setting ............................................................................................................ 27
Option Setting.......................................................................................................... 28
Lock Setting ............................................................................................................ 29
Channel Setting ....................................................................................................... 31
. 33
Enjoying Photo/Music/Movie Playback
Connecting a USB Memory Device/USB Hard Drive
33
Listening to Music
33
Viewing Pictures
33
Watching Movie
33
Appendix .................................................................................................................... 34
Troubleshooting ....................................................................................................... 34
Specifications .......................................................................................................... 35
PC Compatibility Chart .............................................................................................. 36
Wall Mount Kit Specifications .................................................................................... 37
Legal notices........................................................................................................... 38
Calling for Service ..................................................................................................... 39
Dimensional Drawings
The dimensional drawings for the LCD TV set are shown on the inside back cover.
12
Part Names
TV (Front)
TV (Side/Rear)
Headphone
USB
USB terminal
*2
*1: See pages 15, 16, 17 and 18 for external equipment connection.
*2: See pages 14,19,21 and 27 for button operations.
• The illustrations in this operation manual are for explanation purposes and may vary slightly
from the actual operations.
13
Introduction to Connections
Experiencing HD Images
An HDTV without an HD source is just an ordinary TV.
To enjoy HD images on the TV, you should get HD programming from the following:
• Over-the-air broadcasting via HD quality antenna
• HD cable/satellite subscription
• HD compatible external equipment
• For information on updating to HD programming, ask your cable/satellite service provider.
Types of Connection
Image quality differs depending on the terminal used. To enjoy clearer images, check the output
terminals of your external equipment and use its appropriate terminals for higher quality images.
For connecting the TV to external equipment, use commercially available cables.
• The illustrations of the terminals are for explanation purposes and may vary slightly from the actual products.
Image
Quality
Terminal on external
equipment
HD
Quality
Terminal
on the TV
Cable
HDMI-certied cable
Page 15
3.5 mm stereo minijack cable
AUDIO
DVI OUT
Page 15
DVI-HDMI conversion cable
Component video cable
Page 16
Audio cable
AV cable
Page 16
Standard
Quality
Displaying an External Equipment Image Display
To view external source images, select the input source by pressing INPUT on the remote control
unit or on the TV.
1. Press INPUT.
The Input Source list screen displays.
2. Press / to select the input source.
INPUT SOURCE
INPUT
TV
AV
YPBPR
HDMI1
HDMI2
HDMI3
PC
USB
14
TV
AV
YPBPR
HDMI1
USB
PC
HDMI3
HDMI2
An image from the selected source
automatically displays.
3. Press ENTER to confirm.
Connecting to External Equipment
You can connect many types of external equipment to your TV. To view external source images,
select the input source from INPUT on the remote control unit or on the TV. (See pages 14 and 21.)
For connecting the TV to external equipment, use commercially available cables.
CAUTION
• To protect equipment, always turn off the TV before connecting any external equipment.
• Please read the relevant operation manual (Blu-ray disc player, etc.) carefully before making connections.
Connecting a Blu-ray Disc/DVD Player or HD Cable/Satellite Set-top Box
When using HDMI cable ( HDMI 1, 2, or 3):
The HDMI (High Denition Multimedia Interface) terminal is an audio-video interface that enables a
connection for audio and video signals using a single cable. The HDMI terminal supports
high-resolution video input.
• Blu-ray disc player
• DVD player
• HD cable/satellite set-top box
HDMI-certied cable
HDMI OUT
• To enjoy 1080p display capability, connect your external equipment using an HDMI-certied cable or a
component cable and set the equipment to 1080p output.
• Supported Audio format: Linear PCM, sampling rate 32/44.1/48kHz.
When using DVI-HDMI conversion cable ( HDMI 1, 2, 3 or PC ):
• Blu-ray disc player
• DVD player
• HD cable/satellite set-top box
3.5 mm stereo minijack cable
DVI-HDMI conversion cable
AUDIO
DVI OUT
• When using a DVI-HDMI conversion cable, you should make an analog audio connection. In this case, in
addition to connecting a DVI-HDMI conversion cable to the HDMI 1,2,3 terminal, connect a
stereo minijack cable to the AUDIO PC/HDMI terminal.
3.5 mm
15
Connecting to External Equipment
When using Component cable ( Y PB PR ):
• Blu-ray disc player • DVD player
• HD cable/satellite set-top box
Component video cable
(Red)
(Blue)
Y (Green)
COMPONENT OUT
AUDIO-R (Red)
USB
AUDIO-L (White)
Headphone
Audio cable
• To enjoy 1080p display capability, connect your external equipment using an HDMI-certied cable or a
component cable and set the equipment to 1080p output.
• See page 15 for connecting a Blu-ray disc player, DVD player or an HD cable/satellite set-top box to the HDMI
terminal.
Connecting a Game Console, VCR, Camcorder or Cable/Satellite Set-top Box
When using Composite cable ( AV ):
• Game console
• Camcorder
• VCR
• Cable/Satellite set-top box
AUDIO-R (Red)
AV cable
AUDIO-L (White)
VIDEO (Yellow)
AV cable
AUDIO-R (Red)
AUDIO-L (White)
VIDEO (Yellow)
16
Connecting to External Equipment
Connecting an Audio Amplifier
When using coaxial cable:
It is possible to output audio through the DIGITAL AUDIO terminal. PCM audio outputs from the
terminal.
Optical ber cable
OPTICAL
DIGITAL AUDIO INPUT
• Digital Audio output is not available when using an HDMI input.
Connecting an AV Amplifier
HD Cable/Satellite set-top box
HDMI-certified
cable
HDMI OUT
HDMI
IN
HDMI
OUT
• If the image is not in sync with the audio, check the settings of the connected surround system.
• Letting the TV output the audio to an AV amplifier:
17
Connecting to External Equipment
Connecting a PC
Refer to page 35 for a list of PC signals compatible with the TV.
When using HDMI cable ( HDMI 1, 2 or 3):
HDMI-certied cable
HDMI OUT
• The HDMI terminals only support digital signal.
When using DVI-HDMI conversion cable ( HDMI 1,2,3 or PC ):
3.5 mm stereo minijack cable
AUDIO
DVI OUT
DVI-HDMI conversion cable
• Digital Audio output is not available when using an HDMI input.
• Using analog audio connection by headphone jack when connecting to sound bar or external speaker.
When using analog RGB cable (PC IN):
Analog RGB cable
(D-sub 15-pin cable or VGA cable)
3.5 mm stereo minijack cable
RGB
AUDIO
• When using an analog RGB cable, input the audio signal to the AUDIO PC IN/HDMI terminal of PC IN.
18
Watching TV
Turning On/Off the Power
Press POWER on the TV, or POWER on the remote control
unit to turn the power on.
• POWER indicator: Power on, Blue; Power off, red.
Press POWER on the TV, or POWER on the remote control
unit again to turn the power off.
• The TV enters standby and the image on the screen
disappears.
• If you are not going to use this TV for a long period of time, be
sure to remove the AC cord from the AC outlet.
• Small amount of electric power is still consumed even when the
TV is turned off.
• If there is no signal input for 15 minutes, the power will turn to
standby mode automatically.
Setup Wizard
When you turn on the TV for the first time, the
Setup Wizard will guide you through the setup
process. Perform the following steps before
you press POWER on the remote control unit.
1. Insert the batteries into the remote control
unit. (See page 11.)
2. Connect the antenna cable to the TV. (See
page 10.)
3. Plug in the AC cord to the AC outlet. (See
page 8.)
TV Location
Select "Home" or "Store" for the location where you
plan to install the TV. This product qualies for ENERGY
STAR in Home mode default setting.
Are you sure you want Home Mode?
1. Setup Wizard---Picture Mode
• The Setup Wizard screen display at the
first use. Press
to select Picture
Mode.
Are you sure you want Store Mode?
Selecting this Setting Does not conform to Energy Star.
Home Mode (Energy Saving):Select Home Mode to maximize
energy efficiency. Please note if you select Home Mode the
picture will be darker. This mode meets the requirements of
Energy Star® qualification.
Store Mode : Select Store Mode if you would like your picture
to be brighter. At times this mode may use more energy to
operate the Volume/Sound Mode and the Picture Mode. In
this setting, the power consumption may possibly exceed
the limited requirement of the Energy Star® qualification.
Energy Star® is a set of power-saving guidelines issued by
the U.S. Environmental Protection Agency(EPA).
Energy Star® is a joint program of the U.S. Environmental
Protection Agency and the U.S. Department of Energy helping
us all save money and protect the environment through energy
efficient products and pratices.
• The ON-MODE Power under Home Mode should be less than
98.7W.
• The SLEEP-MODE Power should be less than 0.5W.
19
Watching TV
2. Language setting
Auto Scan (Channel search)
• Press
to Select the OSD menu
languages from English, French, or
Spanish.
• Press / to select the desired
language listed on the screen.
Setup Wizard
Menu Language
5. When "Air" or "Cable" is selected
in Antenna setting:
Press / to select "AUTO Scan", and
then press to start channel search.
English
Air / Cable
Air
Cable System
AUTO
Auto Scan
Select
Move
Channel auto search makes the TV look for all
channels viewable in the set area.
MENU Return
Setup Wizard
Menu Language
English
Air / Cable
Cable
Cable System
AUTO
Auto Scan
Select
Move
MENU Return
3. Air/Cable (Antenna setting)
• Make sure what kind of connection is
made with your TV when selecting "Air"
or "Cable".
• Press / to select "Air" or "Cable".
Setup Wizard
Menu Language
Air / CableRF CH
Found
Cable System
English
5Cable
0
AUTO
Auto Scan
Setup Wizard
Menu Language
English
Air / Cable
Cable
Air
Cable System
AUTO
Auto Scan
Select
Move
MENU Return
4. Cable System (Cable setting)
• Press
/ to select Cable System from
among: "AUTO"、"STD"、"IRC" or "HRC".
Setup Wizard
Menu Language
English
Air / Cable
Cable
Cable System
AUTO
Auto Scan
Move
20
Select
MENU Return
Move
Select
MENU Return
Direct Button Operation
22
23
24
25
Off
5
10
15
30
240 180 120 90 60 45
21
Direct Button Operation
Press CC
CC on Mute: Displays the closed caption when
TV’s sound is muted.
3
TV
AV
YPBPR
HDMI1
USB
PC
HDMI3
HDMI2
Press ENTER to confirm.
22
Direct Button Operation
22
/
Press to skip between chapters.
50
23
/
Press to adjust the playback speed.
24
Press to pause or resume the playback.
25
Press to stop the playback and clear the existing memory.
23
Direct Button Operation
24
On-Screen Display Menu
On-Screen Display Menu Operation
Example
PICTURE
SETTING
Setup
Wizard
Standard
English
AV Mode
Menu
Language
Contrast
AirBrightness
/ Cable
Color
Cable
Tint System
Sharpness
Auto
Scan
Color Temp.
MEMC
Move
Backlight
Select
Move
Select
50
50
50
0
50
Cable
AUTO
Normal
Normal
MENU Return
50
MENU Return
1. Press MENU to display the MENU screen,
and press ENTER to select the desired menu.
2. 1 Press / to select the desired menu.
2 Press / to select a specific
adjustment item.
3
Operations vary depending on the function
or item. Refer to the guide display
corresponding to the menu setting screen
for button operations.
3. Press MENU to exit.
Example
AUDIO Setup
SETTINGWizard
Standard
English
Sound Mode
Menu
BassLanguage
AirTreble
/ Cable
Balance
Cable
System
Surround
Auto
Scan
SPDIF Type
Audio Language
Move
Cable
Select
Move
Select
AUTO
On
PCM
English
50
50
0
MENU Return
MENU Return
25
On-Screen Display Menu
Menu Operation Button
Using the remote control
Use the following buttons on the remote control
to operate the menu.
Picture Setting
Adjusts the picture to your preference with the
following picture setting.
Example
PICTURE
SETTING
Setup
Wizard
MENU:
Press to open or close the menu
screen.
Press to select a desired item on
the screen or adjust a selected
item.
ENTER:
Press to go to the next step or
complete the setting.
RETURN:
Press to return to the previous
step.
Using the control panel of the main unit
You can also operate the menu with the control
panel of the main unit.
Button operations on the control panel
correspond to the ones on the remote control
as shown below.
Select
Move
Select
Cable
AUTO
50
50
50
0
50
Normal
Normal
MENU Return
50
MENU Return
1. Press MENU to display the MENU screen,
and then press
to select "Picture" and
press ENTER to enter it.
2. Press / to select a specific adjustment
item and press ENTER to enter the setting.
3. Press
to adjust the setting.
4. Press MENU to exit.
AV Mode
Select the type of picture which best corresponds
to your viewing preferences by selecting Picture
Mode in the PICTURE menu; press
to
select the “Standard” 、“Dynamic” 、“Moive” 、
“User” .
Selected item
Contrast
Brightness
Color
Cursor / on the remote
control.
Cursor / on the remote
control.
MENU: MENU on the remote
control or EXIT on the
remote control while OSD
menu is on.
INPUT: ENTER on the remote
control.
Standard
English
AV Mode
Menu
Language
Contrast
AirBrightness
/ Cable
Color
Cable
Tint System
Sharpness
Auto
Scan
Color Temp.
MEMC
Move
Backlight
Tint
Sharpness
Backlight
button
For less
contrast
For less
brightness
For less color
intensity
Skin tones
become reddish
For less
sharpness
The screen
dims
button
For more
contrast
For more
brightness
For more color
intensity
Skin tones
become greenish
For more
sharpness
The screen
brightens
Color Temp. (Color Temperature)
For a better white balance, use color
temperature correction.
Warm:
Normal:
White with reddish tone
Cool:
White with bluish tone
White balance can be adjusted manually through
the R/G/B Gain between a maximum of 255 and a
minimum of 0 for each color temperature.
26
On-Screen Display Menu
Audio Setting
You can adjust the sound quality to your
preference with the following settings.
Example
AUDIO Setup
SETTINGWizard
Sound Mode
Menu
BassLanguage
AirTreble
/ Cable
Balance
Cable
System
Surround
Auto
Scan
SPDIF Type
Audio Language
Move
Standard
English
Cable
Select
AUTO
On
PCM
English
Select
Move
50
50
0
MENU Return
MENU Return
1. Press MENU to display the MENU screen,
and then press / to select "Audio",
and then press ENTER to enter it.
2. Press / to select a specific adjustment
item.
• Select "Treble", "Bass" or "Balance" and
then press ENTER to set each item.
3. Press / to select the desired setting,
and then press ENTER.
4. Press MENU to exit.
Sound Mode
Press
to select the “Standard” 、“Music” 、
“Movie” 、“ User” .
Selected item
Treble
Bass
Balance
button
For weaker
treble
For weaker
bass
Decrease audio
from the right
speaker
button
For stronger
treble
For stronger
bass
Decrease audio
from the left
speaker
Surround
The surround function produces Surround
effect from the speakers.
On: Makes it possible to enjoy natural,
realistic surround sound.
Off: Outputs the normal sound.
For some discs, setup may be required on your
DVD/BD player. In this case, please refer to the
operation manual of your DVD/BD player.
SPDIF Type
You can output digital audio to an AV amplifier
or similar device whose DIGITAL AUDIO INPUT
terminal is connected to the DIGITAL AUDIO
OUTPUT terminal on the TV. Please select an
audio output format compatible with the audio
format of the program you are watching and
the equipment connected.
PCM: The optical output terminal outputs
audio signal in PCM form. If your digital
audio system does not support Dolby
Digital, select "PCM".
RAW: The optical output terminal outputs
Audio signal in Dolby Digital form. It
reproduces sound from surround program
of digital.
Time Setting
You can adjust the system time to your
preference with the following settings.
Example
TIME SETTING
Setup
Sleep Timer
Menu
Language
Time Zone
Daylight
Saving Time
Air
/ Cable
Wizard
180 Min
English
Pacific
OffCable
Cable System
AUTO
Auto Scan
Move
Select
MENU Return
Move
Select
MENU Return
1. Press MENU to display the MENU screen,
and then press / to select "Time", and
then press ENTER to enter it.
2. Press / to select a specic adjustment
item, and then press / to select the
desired setting, and then press ENTER.
3. Press MENU to exit.
Sleep Timer
Press
to select the sleep timer from among
“Off” 、“5 Min” 、“10 Min” 、“15 Min” 、“30 Min” 、
“45 Min” 、“60 Min” 、“90 Min” 、“120 Min” 、
“180 Min” or “240 Min” .
Timer Zone
Press
to select the timer zone from among
“Pacific” 、“Alaske” 、“Hawaii” 、“Eastern” 、
“Central” or “Mountain” .
Daylight Saving Time
Press
to select the daylight saving time
from among “On” or “Off ” .
27
On-Screen Display Menu
Option Setting
ADVANCED
Example
OPTION SETTING
Menu Language
Transparency
View Mode
Noise Reduction
Advanced
Closed Caption
DLC
Display Mode
Restore Default
Move
English
Off
Wide
Middle
On
Home Mode
Select
MENU Return
1. Press MENU to display the MENU screen,
and then press / to select "Setup", and
then press ENTER to enter it.
2. Press / to select a specific adjustment
item.
3. Press / to select the desired setting,
and then press ENTER.
4. Press MENU to exit.
Menu Language
Press
to select the menu language from
among English、French or Spanish.
Transparency
Press
to select the transparency function
from among On or Off.
View Mode
Press
to select the zoom from among Wide、
Zoom、Cinema、Normal、Dot by Dot、Full.
Noise Reduction
Press
to select the a desired level for
viewing a clearer video image from among
Off、Weak、Middle、Strong.
Produces a clearer video image.
Strong/Middle/Weak:Select a desired level
for viewing a clearer video image.
Off: No adjustment.
Advanced
Ordinarily you can easily adjust the picture as
necessary to change image position using
"Advance". In some cases, however, manual
adjustment is needed to optimize the image.
28
H-POS
V-POS
Clock
Phase
Auto
Move
50
50
50
50
Adjust
MENU Return
H-Pos.: Centers the image by moving it to
the left or right.
V-Pos.: Centers the image by moving it up
or down.
Clock: Adjust when the image flickers with
vertical stripes.
Phase: Adjust when characters have low
contrast or when the image flickers.
Auto: Auto adjust image position.
The default cursor position may not be in the center,
because the screen position variable ranges may
be asymmetrical.
The screen position variable ranges depend on the
View Mode or the signal type. The ranges can be
seen on the position-setting screen.
Closed Caption
Allow you to change the Closed Caption display.
CLOSED CAPTION
CC Mode
Basic Selection
Advanced Selection
Option
Move
CC on Mute
Text1
Service1
Select
MENU Return
CC Mode: Allow you to select the CC
Mode among: On、Off .
Basic Selection: Allow you to select the
basic selection among: CC1、CC2、CC3、
CC4、Text1、 Text2、 Text3 and Text4.
Advanced Selection: Allow you to select
the advanced selection among: Service1、
Service2、Service3、Service4、Service5
or Service6、
On-Screen Display Menu
Option: This function allow you to adjust the
caption screen appearance to suit your
preference.
OPTION
Mode
Font Style
Font Size
Font Edge Style
Font Edge Color
FG Color
BG Color
FG Opacity
BG Opacity
Custom
Font 0
Normal
None
Black
White
Red
Solid
Solid
Select
Move
Lock Setting
Allows you to use a secret number to protect
certain settings from being accidentally
changed.
Example
LOCK SETTING
MENU Return
DLC
0-9
Press
to select the DLC (Dynamic
Luminance Control) from On or Off.
Display Mode
Press
Mode.
----
Enter Password
to select the Home Mode or Store
Restore Default
MENU Return
1. Press MENU to display the MENU screen,
and then press / to select "Lock", and
then press ENTER to enter it.
2. Press to enter the " Enter Password "
selection and use the numeric keys to input
a 4-digit password. The screen will display
the sub-menu, after setting.
3. Press MENU to exit.
RESTORE DEFAULT
The factory password is 0000.
Are you sure?
No
Change Password
Yes
LOCK SETTING
Select
Move
MENU Return
If complex adjustments are made and the
settings cannot be restored to normal, you can
reset the settings to the factory preset values.
Change Password
System Lock
US
Canada
RRT Setting
Reset RRT
Move
On
Next
MENU Return
The Channel Setup settings will not be changed.
The Language settings will not be changed.
The Secret number settings will not be changed.
The TV Location settings will not be changed.
29
On-Screen Display Menu
LOCK SETTING
Enter New Password
Confirm Password
0-9
-------
MENU Return
Enter New Password: Enter a 4-digit Secret
No. with the number buttons on the remote
control to change your password.
Confirm Password: enter your new 4-digit
Secret No. again to confirm.
As a precautionary measure, make a note of your
secret number and keep it in a familiar place.
System Lock
Press
to select the system lock from On
or Off, if you turn off the system lock, then the
following optons (US, Canada, RRT Seting and
Reset RRT) are unavailable for use.
US rating
Press
to enter into US rating following menu.
US
TV Parental Guidelines
Suggested age
TV-Y: All children.
TV-Y7: Directed to older children.
TV-G: General audience.
TV-PG: Parental Guidance suggested.
TV-14: Parents strongly cautioned.
TV-MA: Mature audience only.
Content
FV: Fantasy violence.
V: Violence.
S: Sexual situation.
L: Adult language.
D: Sexually suggestive dialog.
MPAA (Motion Picture Association of
America))
The Movie rating (MPAA) is used for original
movies rated by the Motion Picture Association
of America as broadcasted on cable TV and
not edited for television.
G: General audiences. All ages admitted.
PG: Parental guidance suggested. Some material
may not be suitable for children.
PG-13: Parents strongly cautioned. Some material
may be inappropriate for children under 13.
R: Restricted. Under 17 requires accompanying
parent or adult guardian (age varies in some
jurisdictions).
NC-17: No one 17 and under admitted.
X: X is an older rating that is unfiied with NC-17
but may be encoded in the data of older movies.
Canada Rating
TV
MPAA
N/A
Press
menu.
to enter into Canada rating following
CANADA
Move
Next
MENU Return
Canada English
Canada French
E
E
TV
Move
Select
MENU Return
Canada English
Move
30
Next
MENU Return
E: Exempt: Includes news, sports, documentaries
and other information programming; talk shows,
music videos, and variety programming.
C: Children: Intended for younger children under
the age of 8 years. Pays careful attention to
themes that could threaten their sense of
security and well-being.
On-Screen Display Menu
C8+: Children over 8 years old: Contains no portrayal
of violence as the preferred, acceptable, or only
way to resolve conflict; nor encourage children
to imitate dangerous acts which they may see on
the screen.
G: General: Considered acceptable for all age groups.
Appropriate viewing for the entire family, contains
very little violence, physical, verbal or emotional.
PG: Parental Guidance: Intended for a general
audience, but may not be suitable for younger
children (under the age of 8 ) because it could
contain controversial themes or issues.
14+: Over 14 years: Could contain themes where
violence is one of the dominant elements of the
storyline, but it must be integral to the development of plot or character. Language usage could
be profane and nudity present within the context
of the theme.
18+: Adults: Intended for viewers 18 years and older
and might contain depictions of violence, which
while related to the development of plot,
character or themes, are intended for adult
viewing. Could contain graphic language and
portrayals of sex and nudity.
Canada French
E: Exempt programming.
G: General: All ages and children, contains minimal
direct violence, but may be integrated into the plot
in a humorous or unrealistic manner.
8ans+: General but inadvisable for young children:
May be viewed by a wide public audience, but could
contain scenes disturbing to children under 8 who
cannot distinguish between imaginary and real
situations. Recommended for viewing with parent.
13ans+: Over 13 years: Could contain scenes of
frequent violent scenes and therefore recommended
for viewing with parent.
16ans+: Over 16 years: Could contain frequent violent
scenes and intense violence.
18ans+: Over 18 years: Only for adult viewing. Could
contain frequent violent scenes and extreme
violence.
Channel Setting
Example
CHANNEL SETTING
Air/Cable
Auto Scan
Favorite
Show/Hide
Channel No.
Channel Label
DTV Signal:
Move
Cable
Select
MENU Return
1. Press MENU to display the MENU screen,
and then press / to select "Channel",
then press ENTER to enter it.
2. Press / to select a specific adjustment
item.
3. Press / to select the desired setting,
and then press ENTER.
4. Press MENU to exit.
Air / Cable
• Make sure what kind of connection is made
with your TV when selecting "Air" or "Cable".
/ to select "Air" or "Cable".
• Press
Auto Scan
AUTO SCAN
Cable System
Start to Scan
AUTO
RRT Setting
Rating Region Table setting,Press
RRT seting menu.
to enter into
RRT Setting
Humor Level
Intelligence Level
Erotie Level 20CHARS
Move
Next
MENU Return
Reset RRT
Move
Select
MENU Return
If you select "Air" as the input signal in "Antenna"
item, and then press the to search channels
automatically. The receivable channels will be
stored automatically. when searching channels,
press MENU to stop.
If you select "Cable" as the input signal in
"Antenna" item, you can select Cable System from
among: AUTO、STD、IRC or HRC; and then
press
to "Start to Scan", then press the to
search channels automatically. The receivable
channels will be stored automatically. when
searching channels, press MENU to stop.
Allows you to reset the RRT seting.
31
On-Screen Display Menu
Channel No .
AUTO SCAN
Display the number of current channel.
R F CH :
Foound :
54
0
Channel Label
Display the label of current channel.
DTV Signal
Next
Move
MENU Return
Favorite
Allows you to add channels that you flag to your
favorite channel list.
Press the
to select "Favorite" item, then
press the to enter into the menu.
Press the
to select the desired channel,
then press the "ENTER" to add or remove the
desired channel as a favorite.
FAVORITE
Channel
Channel Name
50-1
50-2
50-13
KOCE-HD
KOCE-SD
KOCE-LB
Favorite
Move Press"ENTER"change MENU Return
Show/Hide
Allows you to Show or Hide the channel.
Press the
to select "Show/Hide" item,
then press the to enter into the menu.
Press the
to select the desired channel,
then press the "ENTER" to show or hide the
channel.
FAVORITE
Channel
Channel Name
50-1
50-2
50-13
KOCE-HD
KOCE-SD
KOCE-LB
Add/Delete
Move Press"OK" change MENU Return
32
Display the quality of current DTV signal.
Enjoying Photo/Music/Movie Playback
Viewing Pictures
movies.
PresstheINPUT buttononthe mainunitoron
theremotecontrol thenpressthebuttons
toselect theUSB modeandthenpressEnter
button.
Pressthebuttonstoselect PHOTO
andthenpressEnter button.
Exit the USB mode by pressing INPUT on the
remote control unit or on the TV then press
0000 buttons to select the desired input source
and press Enter to confirm.
Watching Movie
PresstheINPUT buttononthe mainunitoron
theremotecontrol thenpressthebuttons
toselect theUSB modeandthenpressENTER
button.
Pressthebuttonstoselect MOVIE and
thenpressENTER button.
PARIS.Mp4
PARIS.Mp4
london.Mp4
guilin.Mp4
.jpg, .jpeg, .bmg, .png
.mp3,.wma,.m4a,.aac
.avi,.mp4,.ts,.trp,.mpg,.mkv,.mov,
.dat,.vob,.rm,.rmvb
Listening to Music
PresstheINPUT buttononthe mainunitor
ontheremotecontrol thenpressthe
buttonstoselect theUSB modeandthen
pressEnter button .
Pressthe buttonstoselect MUSIC and
thenpressEnter button.
view picture.
When selecting a movie file:
watch movie.
33
Appendix
Troubleshooting
Problem
No power
Unit cannot be
operated.
Possible Solution
Check if you pressed POWER on the remote control unit.
(See page 19.) If the indicator on the TV is still red,
press POWER on the TV.
Is the AC cord disconnected? (See page 8.)
Has the power been turned on? (See page 19.)
External influences such as lightning, static electricity, may
cause improper operation. In this case, operate the unit after
First turning off the power of the TV or unplugging the AC cord
and re-plugging it after 1 or 2 minutes.
Remote control unit
does not operate.
Are batteries inserted with polarity ( , ) aligned?
(See page 11.)
Are batteries worn out? (Replace with new batteries.)
Are you using it under strong or fluorescent lighting?
Is a fluorescent light illuminated near the remote control
sensor?
Picture is cut off/with
sidebar screen.
Are screen mode adjustments such as picture size made
correctly? (See page 24.)
Strange color,
light color, or color
misalignment
Adjust the picture tone. (See page 26.)
Is the room too bright? The picture may look dark in a room
that is too bright.
Is the sleep timer set? (See page 21.)
The unit’s internal temperature has increased. Remove any
objects blocking vent.
Is connection to other components correct? (See page 14.)
Is the correct input selected? (See page 14 or 22.)
Is the volume too low? (See page 23.)
Have you pressed MUTE on the remote control unit?
(See page 23.)
Power is suddenly
turned off.
No picture
No sound
The TV sometimes
makes a cracking
sound.
This is not a malfunction. This happens when the cabinet
slightly expands and contracts according to change in
temperature. This does not affect the TV’s performance.
The Master Password
If you forgot the password number, reset the secret number by following the procedures below:
1. Press MENU to display the MENU screen, and then press
select Lock and then press ENTER to enter it.
2. Press the master password 8899.
As a precautionary measure, make a note of your secret number and keep it in a safe place.
34
Appendix
Cautions regarding use in high and low temperature environments
When the unit is used in a low temperature space (e.g. room, office), the picture
may leave trails or appear slightly delayed. This is not a malfunction, and the unit will
recover when the temperature returns to normal.
Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location
exposed to direct sunlight or near a heater, as this may cause the cabinet to deform
and the Liquid Crystal panel to malfunction.
Storage temperature: -4°F to +140°F (-20°C to +60°C)
Specifications
Item
LCD
panel
Model:LC-60LE450U/LC-60LE452U
Size
60 ” Class (60 1/32” Diagonal)
Resolution
2,073,600 pixels (1920 x 1080)
TV-standard (CCIR)
VHF/UHF
TV
Function
CATV
Receiving Digital Terrestrial
Channel Broadcast (8VSB)
Digital cable*1
(64/256 QAM)
Audio multiplex
Audio out
Terminals Side
American TV Standard ATSC/NTSC System
VHF 2-13ch, UHF 14-69ch
1-135ch (non-scrambled channel only)
2-69ch
1-135ch (non-scrambled channel only)
BTSC System
8Wx2
OUTPUT
Audio out
VIDEO
AV in
COMPONENT
Component in
USB
Photo/Music mode/Software update
HDMI 1
HDMI in with HDCP
HDMI 2
HDMI in with HDCP
HDMI 3
HDMI in with HDCP
PC IN
ANALOG RGB (PC) in (15-pin mini D-sub female connector),
Audio in (Ø 3.5 mm stereo jack)
ANT/CABLE
75
Unbalance, F Type x 1 for Analog (VHF/UHF/CATV)
DIGITAL AUDIO OUTPUT Optical Digital audio output x 1 (PCM/Dolby Digital)
OSD language
English/French/Spanish
Power Requirement
AC 120V, 60Hz
Power Consumption
Weight
Dimension*2
(W x H x D)
157 W (0.5W Standby with AC 120V)
TV + stand
69 lbs./32 kg
TV only
60.6 lbs./28 kg
TV + stand
54 25/32 x 35 12/32 x 13 inch
TV only
54 25/32 x 32 22/32 x 4 5/ 32 inch
Operating temperature
+32°F to +104°F (0°C to +40°C)
*1
Emergency alert messages via Cable are unreceivable.
*2
The dimensional drawings are shown on the inside back cover.
• As part of policy of continuous improvement, SHARP reserves the right to make design and
specification changes for product improvement without prior notice. The performance specification
figures indicated are nominal values of production units. There may be some deviations from these
values in individual units.
35
Appendix
PC Compatibility Chart
It is necessary to set the PC correctly to display XGA and WXGA signal.
PC
Resolution
720 x 400
VGA
PC
SVGA
XGA
640 x 480
800 x 600
1024 x 768
Horizontal
Frequency
Vertical
Frequency
31.5 kHz
70.0 Hz
31.5 kHz
60.0 Hz
O
37.5 kHz
37.9 kHz
75.0 Hz
60.0 Hz
O
O
48.1 kHz
72.0 Hz
O
46.9 kHz
75.0 Hz
O
48.4 kHz
60.0 Hz
O
56.5 kHz
70.0 Hz
O
60.0 kHz
75.0 Hz
O
VESA Standard
WXGA
1366 x 768
47.7 kHz
60.0 Hz
O
SXGA
1280 x 1024
64.0 kHz
60.0 Hz
O
SXGA+
1400 x 1050
65.3 kHz
60.0 Hz
O
UXGA
1600 x 1200
75.0 kHz
60.0 Hz
O
1080p
1920 x 1080
67.5 kHz
60.0 Hz
VGA and XGA are registerd trademarks of Internatioal Business Machines Corp.
36
Appendix
Wall Mount Kit Specifications
Standard dimensions for wall mount kits are shown below.
( The illustration is based on the LC-80LE857U model as an example )
WALL
a1
WALL MOUNT KIT
a2
b1
a1: Maximum distance
from the mounting hole
a2: Maximum distance
from the TV's center
b1: Distance between the TV's
center and the mounting hole
b2
B
b2: Maximum distance
from the TV's center
b3: Maximum distance
from the mounting hole
b3
c1: Minimum gap
A
LC-90LE657U
VESA screw
hole specs
(A-B)
a1
Width
a2
b1
Height b2
b3
c1
WALL MOUNT KIT
LC-80LE857U/
LC-80LE757U
LC-80LE657U/
LC-80LE650U/
LC-80C6500U
235/8 (600) ?15 3/4 (400)
1319/32 (345)
523/32 (145)
LC-70LE657U/
LC-70LE655U/
LC-70LE650U/
LC-70C6500U
LC-60LE857U/
LC-60LE757U/
LC-60LE755U/
LC-60C7500U/
LC-60LE452U/
LC-60LE450U
LC-60LE657U/
LC-60LE655U/
LC-60LE650U/
LC-60C6500U
77/8 (200)
1239/64 (320)
447/64 (120)
91/16 (230)
91/16 (230)
23/8 (60)
153/4 (400) ?15 3/4 (400)
261/64 (75)
1449/64 (375)
137/64 (40)
1325/64 (340)
77/8 (200)
1449/64 (375)
657/64 (175)
35/32 (80)
LC-70LE857U/
LC-70LE757U/
LC-70LE755U/
LC-70C7500U
c1
1041/64 (270)
111/32 (280)
559/64 (150)
1027/32 (275)
77/8 (200)
1411/64 (360)
65/16 (160)
249/64 (70)
731/64 (190)
1041/64 (270)
23/8 (60)
SCREW
WALL MOUNT
UNIT
Do not install the wall mount kit while your TV is turned on.
It may result in personal injury due to electric shock.
CABINET
MOUNTING
HOLES
DEPTH OF
MOUNTING HOLES
For the screws, refer to the table shown below.
90/80 inch models
Standard screws
M8 (Use 1.25 pitch screws)
Length(Depth of mounting holes)
15/32 (12)
Quantity
4 pcs.
70/60 inch models
M6 (Use 1.0 pitch screws)
NOTE
• Do not mount the TV at a tilt.
• To use this TV mounted on a wall, remove the cable tie as needed.
• Do not use screws that do not comply with the VESA standard screw specifi cations.
• Do not use screws that are longer than the standard length. Screws that are too long may cause damage to the inside of the TV.
• Do not fasten the screws too fi rmly or loosely. This may damage the product or cause the product to fall, leading to personal injury. SHARP is not liable for these
kinds of accidents.
• SHARP is not liable for product damage or personal injury when a non-VESA or non-specifi ed wall mount is used or the consumer fails to follow the product
installation instructions.
37
Appendix
Legal notices
■FCC Part 15
This device complies with Part 15 of the FCC Rules. Operation of this product is subject
to the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply within the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
■FCC warning
Changes or modifications not expressly approved by the party responsible for compliance
with the FCC Rules could void the user’s authority to operate this equipment.
■Cables
Connections to this device must be made with shielded cables with metallic RF/EMI
connector hoods to maintain compliance with FCC Rules and Regulations.
■Canadian notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
“Standard Television Receiving Apparatus-Appareil de reception télévision ordinaire,
Canada BETS-7 / NTMR-7”.
38
LC-60LE450U/LC-60LE452U
39
40