Boss Audio Systems HC 700 Specifications

0514
INSTRUCTIONS
CONTENTS
Panel Introduction
Basic Function
Remote Control Operation
Turn on/off Host
Access main interface
USB/SD Card Operation
Radio Operation
Disc Operation
Play/Eject Disc
DVD/VCD Disc Playback
CD Disc Playback
02
03
05
07
07
07
08
09
09
09
09
09
09
11
12
12
12
12
MP3/WMA Format Disc Playback
Touch Menu Function
BT Operation
ST. Wheel setting
External input operation
Calendar
Calculator
Other Operation
13
13
14
14
14
14
14
14
15
15
17
17
18
19
19
Rear view function
Access setup interface
General setting
Audio setting
Video setting
Language setting
Time setting
Version
Touch calibration
Wiring Diagram
Trouble shooting
Specifications
Accessory
DVD Parental control function
Warning: To ensure safety while driving and to comply with laws, drivers should
not watch video or operate the video device while driving.
01
INSTRUCTIONS
INSTRUCTIONS
Panel Introduction
ACCESSORY
Accessory
10
Quantity
Wire
1PC
USB Cable
1PC
Keys
2PCS
Remote controller
1PC
Warranty card
2PCS
9
DVD Parental control function
1.
/ SRC Button
2. MUTE Button
DVD Parental control function
3. DBAS Button
4. VOL- Button
5. VOL+ Button
6.
7. RESET Button
8. USB Slot
9. Remote Control Receiver
DVD Parental control function: The default set
for DVD is #8 adult, which means all grades of
DVD can be read without entering password. To
change the default grade, you need to follow the
below procedure: Press SETUP button on the
remote, display will show the system set up menu
and the submenu, select password and enter
0000, you will be able to choose the DVD
grade as default.
10. AUX External Input
02
19
INSTRUCTIONS
BASIC FUNCTION
SPECIFICATIONS
Power supply
DC 12V
Power range
10.8-16.0V DC
Max Current Consumption
15A
Ground system
Negative ground
Power Output
85 WattsX4 Channels
1. / SRC button
Short press this button to power on, long press this button to power off.
In normal situation, press PWR button can return to the main menu.
2. MUTE button
Press this button to shut off the sound output, re-press this button can resume the
sound output, long press this button can turn off the TFT LCD display.
3. DBAS button
Press this button to bass on/off.
FM tuner
US frequency range
87.5-107.9MHz
European frequency range
87.5-108MHz
Signal / Noise ratio
55dB
Stereo separation
30dB
Search station volt
20-30dBuv
4. VOL- button
Press this button to reduce the volume.
5. VOL+ button
Press this button to increase the volume.
6.
Press this button can eject the disc.
AM tuner
US frequency range
European frequency range
Limit noise sensitivity
530-1710KHz
522-1620KHz
7. RESET button
Press this button and this unit will be restored to the initial state.
32dB
DVD player
S / N Ratio
70dB
Frequency response
20Hz-20KHz
8. Dual (front and rear) USB
Insert USB removable device so as to read audio/video files.
Warning: You can only use either front or rear USB at a time. Never connect both
front and rear USB at the same time! This could cause malfunctions.
9. Remote control receiver
It is able of receiving infrared signals launched by the remote control matching the unit.
10. Dual (front and rear) AUX
To input external audio.
Warning: You can only use either front or rear AUX at a time. Never connect both
front and rear AUX at the same time.
18
03
INSTRUCTIONS
WIRING DIAGRAM
BASE
This player is equipped with ISO standard connector, please follow below instruction:
12
11
13
Grey/Grey black - Right front speaker (+/-)
White/White black - Left front speaker (+/-)
● Purple/Purple black - Right rear speaker (+/-)
● Green/Green black - Left rear speaker (+/-)
● Pink – Parking Brake (-)
● Blue/White – (Remote control for Amplifier)
Red - ACC ON (+12V)
Yellow – 12 V Constant
● Black – Ground wire
● Blue - Power Antenna / Remote Amp Turn On
● Orange – Back-Up Camera Trigger (+)
●
●
●
●
11. SD slot
12. Disc slot
TROUBLE SHOOTING
13. Slot indicator light
PROBLEM
Cannot power on
04
CAUSE
SOLUTION
Check fuse
Change fuse same as the old one
Some factors cause MPU
wrong operation
Press RES button on the panel by penpoint,
then, power on
After ignition switch
Change battery or fuse
off, setting
information all lose
Reset information and save
Poor performance Weak signal
of radio station
Move the car to another place, then research
Cannot load disk
There is a disk inside
Remove disc before inserting another one
Disc is scratched
Change new disc
Cannot play disc
Put wrong side of disc into
the unit
Insert in the disk with sign side up
Lens is dirty
Clean lens by lens clean disc
Cannot switch
language/subtitle
There is only one language/
subtitle in disc
If disc is not with multi-language/subtitle, it
cannot switch language/subtitle
No image
Other factors cause MPU
wrong operation
Press RES button on the panel by penpoint,
then, power on
Cannot watch
image during
driving
Park the car in a safe place, put the car stall
It’s not allowed to watch image
in “ P ” postion, pull up the hand brake,
during driving
parking brake wire must be grounded
17
Touch screen Calibration
Remote Control Operation
Please follow the below instructions to calibrate when there is no touch or
touch is not accurate.
3. SOURCE Button
Press this button to change mode.
28
Step 1: Press the mode button in the unit to switch to DVD mode.
4. EQ Button
Press this button to choose POP、ROCK、
CLASSIC、EQ off.
Step 2: Insert a DVD disc, after DVD is loaded, press the stop button “
” as show in
picture (1). in the remote short, the unit will display as show in picture (2).
5. SEEK+ ( ) / SEEK-( ) Button
In normal playback MP3、USB、SD songs,
Press this button to previous song or next
song.
Picture ( 1 )
Step 3: Press “
picture (4).
6. VOL+ ( ) / VOL- ( )
Press this button to increase or decrease
volume level.
Picture ( 2 )
” in the remote as show in picture (3), the unit will display as show in
7. SEL Button
Press this button to choose sound feature.
8. LOUD Button
Press this button to startup LOUD function.
Picture ( 3 )
Picture ( 4 )
Step 4: Press “ ” button in the remote and then quickly press “ ” button as show in
picture (5) and you will enter the touch calibration interface as show in picture (6).
Picture ( 5 )
Picture ( 6 )
Step 5: Use the touch pen to touch top left corner, top right corner, down right corner,
down left corner, when the cross cursor stop at each corner, touch the center of the
cursor. Then the panel will display OK and leave the calibration interface and the unit
regained touch as show in picture (7).
Picture ( 7 )
16
POWER ON/OFF
AMS / RPT
MUTE
TITLE
SOURCE
AUDIO
EQ
GO TO
SEEK+ / SEEK-
SUBTITLE
VOL+ / VOL-
PBC
SEL
UP / DOWN / L / R ENTER
LOUD
SLOW
BAND / P / N
ANGLE
LOC / RDM
SETUP
STOP
OSD
PLAY / PAUSE
ZOOM
ST / PROG
MENU
0-10+
DSP
9. BAND-P/N Button
In radio mode, press this button to choose
band.
In VCD、DVD mode, press this button to
choose PAL 、AUTO or NTSC system.
10. LOC / RDM Button
In radio mode, press this button to switch
between local and direction.
In VCD、CD mode, press this key to
randomly play.
11. STOP Button
Press this button to stop playing.
12. PLAY / PAUSE Button
Press this button to switch between play
and pause.
In stop mode, press this button to play.
1. POWER Button
Press once to switch on, press again to
switch off.
2. MUTE Button
Press once to turn off audio output,
press again to resume volume level.
13. ST / PROG Button
In radio mode, press this button to choose
stereo or mono station.
In audio mode, it can help STOP button to
programmed play.
05
INSTRUCTIONS
INSTRUCTIONS
14. 0-10+ Button
Press this button to choose desired song、
section、preset stations.
Decimal numbers, for example the 19th
song, press 10+ and 9 button.
23. ANGLE Button
In DVD mode, press this button to change
play angle.
24. SETUP Button
In audio mode, press this button to choose
different set items.
15. AMS / RPT Button
In radio mode, press this button to browse
stored stations.
In audio mode, press this button to play
repeatedly.
25. OSD Display
Press this button to display the title chapter
and the left time.
16. TITLE Button
In DVD mode, press this button to play
back to the top menu of disc.
26. ZOOM Button
In DVD/VCD mode, press this button to
ZOOM in.
17. AUDIO Button
In DVD mode, press this button to switch
language of dialogue.
In VCD mode, press this button to choose
left track、right track and stereo.
27. MENU Button
Press button to back to the main menu.
18. GO TO Button
In DVD mode, press this button, you can
define playing time.
BATTERY CHANGE
When control distance of remote control
becomes shorter or no function, please
change battery. Please confirm polarity
before change.
28. DSP
Press this button to show the time.
19. SUBTITLE Button
In DVD mode, press this button to switch
language of subtitle.
One hand press stopper, then pull out
battery.
20. PBC Button
In VCD mode, press this button to display
all song menus, work with number button
to choose songs.
Version
Touch the icon [
]in setting interface to enter the
interface below to check the software version number
of DISC/MCU/TFT/BT (The version information is displayed
please prevail in kind.)
Touch calibration
If the touch position is biased, you may touch the icon “Calibrate” for calibration.
Touch the icon[
]in setting interface to find the setting bar[
and then touch any icon[
]to enter the following calibrating interface.
十
Touching methods
Use touch pen to click the center of “+” icon, and move along with center of “+” icon so
as to calibrate the screen. It shall automatically save data and exit after screen calibration.
Please accurately click all positions on screen, or the accuracy of touch calibration shall
be affected.
21. UP、DOWN、LEFT、 RIGHT、ENTER Put battery into controller.
Button
When playing MP3、USB、SD returns to
song menu, up、down selections can be
up / " " button or down / " " key to
select up and down, select and press " "
key to confirm.
Insert battery holder into controller.
The selected tracks can be played. Press
the left or right arrow keys to " " or " "
key, can be on the next page function
operation.
22. SLOW Button
In audio mode, press this button to slow
backward and slow forward.
06
],
15
Access setup interface
Turn on/off
Click [Setting] icon on main interface to access setup interface.
When the ignition switch is put in ACC or ON position, Press power button on the front
panel to turn on the unit. After the host starts, hold power button for 3 seconds, the host
will turn off.
General setting
Click
icon on setup interface to access general setting
interface, as shown in below PIC 1 diagram:
In General setting interface, you may set the functions On or
Off, or click the icon [ ]to preview the wallpapers up and
down and set your favorite wallpaper
Access main interface
Turned on, the interface to return the icon to switch to the main interface. As shown
below:
PIC 1
Wallpaper
Touch the icon[
]in wallpaper bar[
]to change the wallpaper.
Audio setting
Touch the function icons so as to access the corresponding function operations.
Touch the [
] icon or use the touch pen/finger gently sliding around the screen to
switch to the main menu page.
Click
icon on setup interface to access audio setting
interface, as shown in right (PIC 2) diagram:
You can turn on or turn off the existing functions on audio
setting interface and adjust the rearview volume.
PIC 2
Video setting
Click
icon on setup interface to access video setting
interface, as shown in right (PIC 3) diagram:
At video setting interface, you can adjust brightness,
contrast, saturation and hue of the video.
PIC 3
Language setting
During use, you can select your familiar language to display
menu by language setup. Click
icon on setup interface to
access language setting interface, as shown in right (PIC 4)
diagram:
In the languagebar [
] you need to set, touch the
correspondingicon[
]to select your familiar language.
When there is a USB device/SD card connected, the unit can conduct the playback of
audio/video/image files in the USB device/SD card.
Insert/Eject USB storage device
1. Connect a U disc recorded with media information to the unit by a USB connecting
cable.
2. When there is a need to eject the USB device, exit the USB device playback screen
first, and then take out the device.
Insert/eject SD card
1. Insert a SD card recorded with media information into the SD card slot in the unit
correctly until it is locked.
2. When pulling out the SD card, exit SD card playing state first, then press the SD card
and it shall pop up after unlocking.
PIC 4
Time setting
Click icon on
setup interface to access time setting
interface.as shown in right (PIC 5) diagram:
Touch the icon [
]of Time mode, Year, Month,
Date, Hour, Minute for setting.
PIC 5
14
USB/SD Card Operation
Enter/exit
Insert a USB storage device or SD card to automatically play data contained in it. If the
unit has connected with a USB device or SD card, touch [USB] icon in the multimedia
interface to enter into the external storage playback interface; Touch [SD] icon to enter
into the SD card playback interface. During playback, touch the top center area of the
screen to pop up the touch menu, operate touch menu to perform various playback
controls.
Play
After SD card/USB removable device being read out, the operation methods are similar
to disk operation methods.
07
Radio Operation
1. Enter/exit
Touch [Radio] icon in the main interface to enter into the radio interface.
Touch
icon to return to main interface, and then touch other function icons so as to
exit radio mode.
2. MUTE on/off
Click
icon to switch MUTE on and off.
3. Loudness on/off
Click
icon so as to turn on/off loudness function.
Other Operation
Rear view function
In any running state, the video signal can switch to reverse video state when reversing
the car, and the system shall return to its initial running state after reversing the car.
Warning
Do not rely on CCD system completely, please make sure you use direct eyesight while
driving. Back rearview system only assists in driving. As the distance range of rearview
system is limited, completely relying on the rearview system during driving may cause
accidents.
4. Search/Save radio stations
Short press
icon to browse the stored radio stations.
FM band can save 18 radio stations (Six stations for
FM1/FM2/FM3), AM band can save 12 radio stations
(Six stations for AM1/AM2).
5. Band selection
Click
icon so as to switch among FM1, FM2, FM3, AM1,
AM2 bands.
Rearview backup image
Reverse field simulation
6.Turn on/off the Long/Short-range
Click
icon, the search pattern in the local search (LOC) and remote search (DX)
switch between.
LOC feature is turned on after the signal is strong enough only to listen to those in good
condition and receiving radio station; DX enabled, you can receive remote weak radio
signals.
Note: This function is available only when FM band is selected.
7. Stereo on/off
When receiving stereo signals, click
icon to turn on/off stereo.
Click
icon so as to slide screen angle.
8. TA (Receive traffic information)
ON: When the traffic station is turned on, the radio will automatically search for traffic
stations. After a station is searched, screen displays “TP”. Only when traffic information
is broadcasted can it be received, after traffic information is completed, the radio will
automatically switch to the previous mode.
OFF: Repress [TA] button to close TA function. In other modes, traffic announcement will
automatically switch to radio mode, after the traffic announcement is completed, it will
automatically switch to the previous mode.
9. AF
Touch the button to turn the AF function on/off. AF function is turned on, When the
received station signals become weak, the radio will automatically fine-tune to other
frequencies. When receiving an emergency announcing, the screen will display warning
message.
10. PTY
Touch the button the screen displays program types, users can search station according
to program type.
Note: If the unit does not have RDS function, it has no AF/TA/PTY function.
08
13
ST. Wheel setting
Disc Operation
1. Click on the [
] icon in the main interface into the SWC. settings interface.
2. The original vehicle to the control line positive,
negative with the machine control line in the
positive and negative connection.
3. Click the SWC buttons will appear
corresponding operating tips, and fundamental
operation prompts the SWC feature set.
4. Set function to save the settings and click the
Confirm icon to confirm.
Note: To modify function settings, repeat procedures 3~4.
To reset functions, click Reset icon, all the settings set before shall be cleared, repeat
procedures 3~4 for resetting.
External input operation
Connect the video input plug with external video input jack, and connect the audio input
plug with external audio input jack.
Touch [AUX-IN] icon on main interface to access external AUX-IN interface.
Region 2
Audio →You can adjust the volume, bass, pitch for input audio. You can adjust the
speaker volume by adjusting the front and back, left and right column.
Video →You can adjust the brightness, contrast, saturation and hue for input video.
You can also choose the video standard mode.
Warning: In AUX-IN mode, you can adjust the angle of screen by press region 1 & region 2.
Press Region 1 to slide up, press Region 2 to slide down.
TT
3. CD Disc Playback
After a CD is inserted, system shall access disk reading
state immediately.
When there is a disk in the device, click [Disk] at the main
interface so as to access disk reading state.
After the disk being read out, system shall automatically
play in sequence.
1/1
CH
1/48
VOL
x
26
00: 01
: 44
00: 09: 43
PIC 1
5. Touch Menu Function Description
MUTE
VOL
Touch this icon to switch MUTE on and off.
Play/pause
Touch the button to pause, retouch it to continue to play.
00: 01
: 44
26
00: 09: 43
Stop
Touch the button to enter into pre stop status.
Fast forward/backward
Consecutively touch this button to select the speed of fast-forward/fast-backward.
Calendar
Touch the icon [
2. DVD/VCD disc playback
During playback of disc, touch the middle lower area of the screen to pop up the touch
menu, operate the touch menu to perform various playback controls. (PIC 1)
4. MP3/JPEG/MPEG4 disk playing
When the disk contains readable files, such as MP3/JPEG/MPEG4 files, it shall be
automatically read out and played after slipping into DVD player.
During playing, touch the screen area and the touch menu shall pop up. Operate the
touch menu for various playing.
x
TT 1/1 CH 1/48
Region 1
此图
1. Play/eject disc
Play disc
Insert the disc into the disc slot with the printing surface up, system will detect the disc
and automatically take it in to read and play.
Eject disc
(1) Click
button on the panel to eject the disc.
(2) If a disc has not been took away 15 seconds after it is ejected, system will
automatically take in the disc but not play.
Do not insert two discs or more.
] in main interface to enter
thefollowing Calendar interface:
The previous/next song
Touch the button to select the previous/next song.
Access next menu
Touch it to access the next menu interface.
Calculator
Touch the icon [
]in main interface to enter
calculator interface to operate +/-/×/÷
12
Disc
Touch this icon to eject disc.
Stereo on/off
Touch it so as to turn on/off stereo.
09
INSTRUCTIONS
BT Operation
Return to root menu
Touch this icon, it shall return to root menu of disk in DVD state and access PBC menu
playing in VCD state. All chapters in the disk shall be displayed on the interface, touch
the chapter icon directly for playing.
1. Enter/exit
Touch the icon [
] in main interface or under Radio/SD/USB/Media/BT Music status
to enter BT [
] main interface;
Touch
icon to exit BT interface.
Access title menu
Press this button to return to title menu of the disk. Directly click menu bar at title menu
interface for playing.
2. Pair/link
To use BT hand-free function, make connection first, i.e.
match the host with the BT mobile phone.
Operation methods:
Set the host to be matching state, and open the BT of
your mobile phone and use the mobile phone to search device, the mobile phone shall
prompt to match password with the BT when it has searched the BT device.
Input BT password (0000) to the mobile phone and confirm. The mobile phone shall
prompt whether authorize to this device, please select [Yes]. Phone and BT shall
automatically connect within 20 seconds. Under any working mode, the host shall
convert to BT state if there is an incoming call. And the host shall restore to current
mode after hanging up.
When the BT device matches with this device, the connection status shall display
“ device paired ”, otherwise, it shall display “ SEARCHING FOR DEVICE ”.After connect
sucessfully, will show BT friendly name "BOSS AUDIO
3. Dialing
You can dial on mobile phone directly or input phone number through the number
buttons on the screen, click
to delete if there is input error.
After input the phone number, click
to make a call, and click
to hang up the phone.
Click
during a call so as to switch the voice between car speaker and mobile phone.
Repeat play
In playing state, touch this button to start repeat play function:
Chapter repeat → Title repeat →Repeat All → Off
During VCD playing, this function only works when PBC is off.
Language selection
Touch this button to select language.
Digit keyboard
Touch this button and digit keyboard shall appear, click number buttons directly to
select tracks for playing.
Switch play order
Touch this button to switch the play order.
Zoom in/Zoom out image
Touch this button to zoom in /zoom out the image.
Under audio/video playing mode or radio mode, the screen center will display the
picture below when adjusting the volume button.
VOL
26
Setting
5. BT music
Touch the icon [
]or the [
]in the main interface to
enter BT music interface, as is shown below:
Touch this button to enter setting interface
EQ
Touch this icon to display EQ mode one by one for selecting.
EQ OFF POP
4. Call records
Click
to access call records interface.
Touch this button to check all the dialed phone numbers.
Touch this button to check all the phone numbers of received calls.
Touch this button to check all the phone numbers of missed calls.
The button to enter BTmain
interface Previous song Play/Pause Next song
ROCK CLASS
Mute on/off
10
The button to enter
LOUD on/off setting
interfac
6.Disconnect BT
Disconnect: When there is a need to disconnect the BT device, directly touch the icon
[
]at lower right corner of the BT main interface to disconnect the BT device.
11