AltoShaam 1000-TH-II/D-SPLIT Service manual

®
OPERATION and CARE MAN UAL
500-TH-II
1000-TH-II
TWO OVENS STACKED
ON CASTERS
750-TH-II/D
Low Temperature
Cooking & Holding Ovens, Electric
Models: 500-TH-I I
500-TH-I I / D
750-TH-I I
750-TH-I I / D
1000-TH-I I-S PLIT
1000-TH-I I / D-S PLIT
COOK/HOLD/SERVE SYSTEMS
W164 N9221 Water Street ● P.O. Box 450 ● Menomonee Falls, Wisconsin 53052-0450 U.S.A.
WEBSITE:
PHONE: 262.251.3800
FAX: 262.251.7067 • 800.329.8744 U.S.A. ONLY
262.251.1907 INTERNATIONAL
www.alto-shaam.com
800.558.8744 U.S.A./CANADA
PRINTED IN U.S.A.
#825/33/37 • 7/04
®
LOW TEMPERATURE COOKING AND HOLDING OVENS
properly with a source voltage of between 220
volts and 240 volts.
U N PA C K I N G a n d S E T- U P
The Alto-Shaam Cooking and Holding
Oven has been thoroughly tested,
checked for calibration, and inspected
to insure only the highest quality oven is
provided. When you receive your oven,
check for any possible shipping damage
and report it at once to the delivering
carrier. SEE TRANSPORTATION DAMAGE
®
®
Ensure that the voltage conversion switch position and the
available power source match.
AND CLAIMS SECTION LOCATED IN THIS MANUAL .
The oven, complete with unattached items and
accessories, may be delivered in one or more packages.
Check to insure that all the following items have been
received as standard with each unit:
Drip Pan
Wire Shelves
NOTE: ALL 208-240 volts units are shipped from the
factory with the voltage conversion switch in
the 220-240 volt position.
Oven Side Racks
External Drip Tray
Save all the information and instructions packed inside
the oven. Complete and return the warranty card to the
factory as soon as possible to insure prompt service in
the event of a warranty parts and labor claim.
Optional 5" (127mm) casters or 6" (152mm) legs must
be installed on the oven before use. For the best
service, the oven should be installed level. The oven
should NOT be installed in any area where it may be
affected by steam, grease, dripping water, high
temperatures or any other severely adverse conditions.
NOTE: All claims for warranty must include the full
model number and serial number of the oven.
E L E C T R I C A L I N S TA L L AT I O N
C.All 125 volt rated units will function properly with
a source voltage of between 100 volts and 125
volts, 60 Hz.
2. The 125 volt rated units are provided with a cord and
plug [NEMA #5-20P]. Have a licensed electrician
install the proper outlet configuration as required for
the unit in accordance with applicable, local electrical
codes. This will assure a safe and trouble-free
installation.
3. Remember to position the oven so that the power
cord is easily accessible in case of an emergency.
4. This oven must be grounded in accordance with
requirements of the National Electrical Code or
applicable country or local codes.
ENSURE THE POWER
SOURCE MATCHES THE
VOLTAGE STAMPED ON
CABINET NAMEPLATE
S TA R T- U P
1. Before operating the oven, clean both the interior
and exterior of the unit with a damp cloth and mild
soap solution. Rinse carefully to remove all
detergent residue.
1.An oven identification tag is permanently mounted on
the oven.
A.All 208-240 volt 500-TH models will function
properly within a voltage range of 200 volts and
240 volts.
B.750-TH and 1000-TH models at 208-240 volts
are dual rated units with a conversion switch
mounted under an access cover on the rear of the
oven, near the power cord.
With the voltage conversion switch in the 200 volt
through 208 volt (UPPER) position, the oven will
function properly with a source voltage of between
200 volts and 208 volts.
With the voltage conversion switch in the 220-240
volt (LOWER) position, the unit will function
2. Clean and install the oven side racks, oven shelves,
and external drip tray. Shelves are installed with the
curved edge toward the back of the oven. Insert the
drip pan on the interior bottom surface of the oven.
3. Before operating the unit with product, become
familiar with the operation of the controls. Read the
following “Operation” section of this manual and
operate the various control functions.
DISCONNECT CABINET FROM POWER SOURCE
BEFORE CLEANING OR SERVICING.
AT NO TIME SHOULD THE UNIT BE STEAM
CLEANED, WASHED DOWN, OR FLOODED
WITH WATER OR LIQUID SOLUTION. DO
NOT USE WATER JET TO CLEAN.
SEVERE DAMAGE OR ELECTRICAL
HAZARD COULD RESULT.
WARRANTY BECOMES VOID IF UNIT IS FLOODED.
#825/33/37
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
1
I N S TA L L AT I O N
DRIP TRAY MOUNTING INSTRUCTIONS
LOW TEMPERATURE
COOKING & HOLDING OVENS
MODELS:
500-TH
750-TH/II
767-SK
®
1000-TH-I
1000-TH-II
EXTRA LARGE DRIP PAN [Optional]
1000-TH • 1000-TH-III = A/S PN: 1115
Bottom of Extra Large Drip Pan is positioned on the bottom
(lowest) side-rack position, just above the Standard Drip Pan.
❋
STANDARD DRIP PAN
[Bottom of oven interior • Below side-racks]
DRIP TRAY
❋
WHEN MOUNTING DRIP TRAY,
SEAL DRIP TRAY HOLDER TO
UNIT WITH AN R.T.V. SEALANT
DRIP TRAY HOLDER
❋
3: 32 x 1/2" SCREWS
[A/S PN: SC-2425]
❋ See individual model service manual, views
and parts lists, for Alto-Shaam part numbers.
®
W164 N9221 Water Street • P. O. Box 450
Menomonee Falls, Wisconsin 53052-0450
#243B • 3/88
PG .
2
#825/33/37
INSTALLATION / OPERATION / SERVICE MANUAL
I N S TA L L AT I O N
EXTERIOR DIMENSIONS (NOT
TO SIZE)
ELECT.
CONN.
2-5/8"
(67mm)
A L T O -S H A A M
34-3/8"— (873mm)
CL
C
L
ELECTRICAL CONNECTION
ADD: 6" (152mm)
For Casters or Legs
500-TH-II
40 lb max.
Capacity
27-3/8"—(695mm)
24-1/4"—(616mm)
3-1/8"—(79mm)
27-3/8"—(695mm)
SHAAM
6"—(152mm)
FOR CASTERS
31-1/4"— (794mm)
34-3/8"— (873mm)
ALTO-
69"— (1753mm)
75"— (1905mm)
17-1/2"
(445mm)
22-1/4"
(565mm)
ELECTRICAL CONNECTION
28-1/4" (718mm)
31-3/8"— (797mm)
50-1/2"— (1283mm)
2-5/8"
(67mm)
ELECTRICAL
CONNECTION
3-1/8" (79mm)
FROM TOP
3-1/8"
(79mm)
FROM TOP
C
L
53-3/4"—(1365mm)
3-1/8"—(79mm)
28-1/4"—(718mm)
ELECTRICAL
CONNECTION
30-7/8"—(784mm)
23-1/4"—(591mm)
22-1/4"
(565mm)
CL
2-5/8"
(67mm)
40-3/4"—(1035mm)
25-7/8"—(657mm)
25-3/8"—(645mm)
CL
ELECTRICAL
CONNECTION
6" (152mm)
FOR CASTERS
750-TH-II
1000-TH-II-SPLIT
100 lb max.
Capacity
120 lb max.
Capacity
1000-TH-II
120 lb max.
Capacity per Compartment
OPTIONS & ACCESSORIES
DESCRIPTION
ITEM
Bumper Corner Guards ( SET OF FOUR ) .......5221
Carving Holders
—Prime Rib Holder ..........................HL-2635
—Ship Round Holder.............................4459
Casters, 5" (127mm)..............................4007
Door Lock with Key .......................LK-22567
Drip Pan, Extra Deep
—1000-TH only ...................................1115
Drip Pan, with drain
—500-TH ..........................................14813
—750-TH (with drain) ..........................14831
—1000-TH ........................................14824
#825/33/37
DESCRIPTION
ITEM
Full Perimeter Bumper
—1000-TH-II/Split, 1000-TH-I .................4994
Legs, 6" (152mm) ....................................5205
Security Panel & Key Lock
—500-TH ...............................................4366
—750-TH-II (with slab door) ......................4367
—750-TH-II/D (with window door) .......... 14374
—1000-TH .............................................4368
Shelf, Stainless Steel Rib Rack
—750-TH..........................................SH-2743
—1000-TH-II/SPLIT...........................SH-2773
Stacking Hardware .............................5000811
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
3
O P E R AT I O N
®
OFF
12
3
9
0
5
6
200
7
15
8
0
0
10
4
30
16
0
OFF
350
180
ON
100 F
F
2
10
140
120
HOLD
HOLDING INDICATOR
LIGHT
COOK
ON/OFF
POWER SWITCH
HOLDING
THERMOSTAT
1. Turn oven POWER SWITCH ‘ON’.
— POWER ‘ON’ INDICATOR LIGHT will illuminate
and will remain lit as long as the Power Switch is
in the ‘ON’ position.
2. Set the HOLD THERMOSTAT to the required
holding temperature.
— HOLDING INDICATOR LIGHT will illuminate as
the Hold Thermostat calls for heat. This process
will continue as long as the Power Switch and
Hold Thermostat are ‘ON’.
3. Set COOK THERMOSTAT to the required cooking
temperature.
4. To preheat the oven, activate the Cook Thermostat
by turning the COOKING TIMER clockwise.
— COOKING INDICATOR LIGHT and HOLDING
INDICATOR LIGHT will illuminate as the unit
calls for heat. This process will continue until the
COOKING TIMER cycles to the ‘OFF’ position.
These instructions are basic operational guidelines only.
For complete instructions, see A Guide to Low
Temperature Cooking and Holding by HALO HEAT
packed with the oven.
4
#825/33/37
COOKING
TIMER
POWER ON
INDICATOR LIGHT
G E N E R A L O P E R AT I O N
PG .
250
60
OFF
1
11
200
80
OFF
COOKING INDICATOR
LIGHT
COOKING
THERMOSTAT
COOKING OVEN CHARACTERISTICS
The oven is equipped with a special, high-heat-density,
heating cable. Through the Halo Heat concept, the
heating cable is mounted against the walls of the
cooking cavity to provide an evenly applied,
thermostatically controlled, heat source. The design and
operational characteristics of the oven eliminate the
need for a moisture pan or a heat circulating fan.
Through even heat application, the quality of a food
product is maintained for many hours.
DISCONNECT CABINET FROM POWER SOURCE
BEFORE CLEANING OR SERVICING.
AT NO TIME SHOULD THE UNIT BE STEAM
CLEANED, WASHED DOWN, OR FLOODED
WITH WATER OR LIQUID SOLUTION. DO
NOT USE WATER JET TO CLEAN.
SEVERE DAMAGE OR ELECTRICAL
HAZARD COULD RESULT.
WARRANTY BECOMES VOID IF UNIT IS FLOODED.
INSTALLATION / OPERATION / SERVICE MANUAL
O P E R AT I O N
GENERAL HOLDING GUIDELINES
Chefs, cooks and other specialized food service
personnel employ varied methods of cooking. Proper
holding temperatures for a specific food product must be
based on the moisture content of the product, product
density, volume, and proper serving temperatures. Safe
holding temperatures must also be correlated with
palatability in determining the length of holding time for
a specific product.
Halo Heat maintains the maximum amount of
product moisture content without the addition of water,
water vapor, or steam. Maintaining maximum natural
product moisture preserves the natural flavor of the
product and provides a more genuine taste. In addition
to product moisture retention, the gentle properties of
Halo Heat maintain a consistent temperature throughout
the cabinet without the necessity of a heat distribution
fan, thereby preventing further moisture loss due to
evaporation or dehydration.
In an enclosed holding environment, too much
moisture content is a condition which can be relieved.
A product achieving extremely high temperatures in
preparation must be allowed to decrease in temperature
before being placed in a controlled holding atmosphere.
If the product is not allowed to decrease in temperature,
excessive condensation will form increasing the moisture
content on the outside of the product.
Most Halo Heat Holding Equipment is provided
with a thermostat control between 60° and 200°F
(16° to 93°C). If the unit is equipped with vents, close
the vents for moist holding and open the vents for
crisp holding.
HOLDING TEMPERATURE RANGE
MEAT
BEEF ROAST — Rare
BEEF ROAST — Med/Well Done
FAHRENHEIT
CELSIUS
140°F
60°C
160°F
71°C
BEEF BRISKET
160° — 175°F
71° — 79°C
CORN BEEF
160° — 175°F
71° — 79°C
PASTRAMI
160° — 175°F
71° — 79°C
140°F
60°C
140° — 160°F
60° — 71°C
PRIME RIB — Rare
STEAKS — Broiled/Fried
RIBS — Beef or Pork
160°F
71°C
160° — 175°F
71° — 79°C
HAM
160° — 175°F
71° — 79°C
PORK
160° — 175°F
71° — 79°C
LAMB
160° — 175°F
71° — 79°C
VEAL
POULTRY
CHICKEN — Fried/Baked
160° — 175°F
71° — 79°C
DUCK
160° — 175°F
71° — 79°C
TURKEY
160° — 175°F
71° — 79°C
GENERAL
160° — 175°F
71° — 79°C
FISH — Baked/Fried
160° — 175°F
71° — 79°C
LOBSTER
160° — 175°F
71° — 79°C
SHRIMP — Fried
160° — 175°F
71° — 79°C
120° — 140°F
49° — 60°C
CASSEROLES
160° — 175°F
71° — 79°C
DOUGH — Proofing
80° — 100°F
27° — 38°C
EGGS —Fried
150° — 160°F
66° — 71°C
FROZEN ENTREES
160° — 175°F
71° — 79°C
HORS D'OEUVRES
160° — 180°F
71° — 82°C
PASTA
160° — 180°F
71° — 82°C
PIZZA
160° — 180°F
71° — 82°C
180°F
82°C
FISH/SEAFOOD
BAKED GOODS
BREADS/ROLLS
MISCELLANEOUS
POTATOES
PLATED MEALS
180°F
82°C
SAUCES
140° — 200°F
60° — 93°C
SOUP
140° — 200°F
60° — 93°C
VEGETABLES
160° — 175°F
The holding temperatures listed are suggested guidelines only
#825/33/37
INSTALLATION / OPERATION / SERVICE MANUAL
71° — 79°C
.
PG .
5
CARE AND CLEANING
The cleanliness and appearance of
this equipment will contribute
considerably to operating efficiency
and savory, appetizing food. Good
equipment that is kept clean works
better and lasts longer.
8.
Remove excess water with sponge and wipe dry
with a clean cloth or air dry. Leave doors open
until interior is completely dry. Replace side racks
and shelves.
9.
Wipe door gaskets and control panel dry with a
clean, soft cloth.
CLEAN DAILY
10. Interior can be wiped with a sanitizing solution
after cleaning and rinsing. This solution must
be approved for use on stainless steel food
contact surfaces.
1.
Disconnect unit from power source, and let cool.
2.
Remove all detachable items such as wire shelves,
side racks, and drip pans. Clean these
items separately.
3.
Wipe the interior metal surfaces of the
oven with a paper towel to remove loose
food debris.
4.
Clean the interior metal surfaces of the
cabinet with a damp clean cloth or sponge
and any good commercial detergent.
NOTE: Avoid the use of abrasive cleaning compounds,
chloride based cleaners, or cleaners containing
quaternary salts. Never use hydrochloric acid
(muriatic acid) on stainless steel.
5.
Spray heavily soiled areas with a water soluble
degreaser and let stand for 10 minutes, then
remove soil with a plastic scouring pad.
6.
Wipe control panel, door vents, door handles, and
door gaskets thoroughly since these areas harbor
food debris.
7.
Rinse surfaces by wiping with sponge and clean
warm water.
11. To help maintain the protective film coating on
polished stainless steel, clean the exterior of the
cabinet with a cleaner recommended for stainless
steel surfaces. Spray the cleaning agent on a clean
cloth and wipe with the grain of the stainless steel.
12. Clean any glass with a window cleaner.
Always follow appropriate state or local health (hygiene)
regulations regarding all applicable cleaning and
sanitation requirements for equipment.
CLEAN THE DOOR VENTS
Door vents need to be inspected and cleaned
as required.
DO NOT USE OVEN IF CONTROLS ARE
NOT PROPERLY FUNCTIONING
Refer to the Trouble Shooting Guide located in this
manual or call an authorized service technician.
CHECK OVERALL CONDITION OF
OVEN ONCE A MONTH
Check the oven once a month for physical damage and
loose screws. Correct any problems before they begin to
interfere with the operation of the oven.
AT NO TIME SHOULD THE INSIDE OR THE OUTSIDE OF
THE OVEN BE WASHED DOWN, FLOODED WITH
WATER, OR LIQUID SOLUTION. DO NOT USE WATER
JET TO CLEAN. N E V E R S T E A M C L E A N
S E V E R E DAMAGE OR ELECTRICAL HAZARD COULD RESULT.
WARRANTY BECOMES VOID IF CABINET IS FLOODED.
PG .
6
#825/33/37
INSTALLATION / OPERATION / SERVICE MANUAL
S A N I TAT I O N
Food flavor and aroma are usually so closely related
that it is difficult, if not impossible, to separate them.
There is also an important, inseparable relationship
between cleanliness and food flavor. Cleanliness, top
operating efficiency, and appearance of equipment
contribute considerably to savory, appetizing foods.
Good equipment that is kept clean, works better and
lasts longer.
Most food imparts its own particular aroma and many
foods also absorb existing odors. Unfortunately, during
this absorption, there is no distinction between GOOD
and BAD odors. The majority of objectionable flavors
and odors troubling food service operations are caused
by bacteria growth. Sourness, rancidity, mustiness,
stale or other OFF flavors are usually the result of
germ activity.
The easiest way to insure full, natural food flavor is
through comprehensive cleanliness. This means good
control of both visible soil (dirt) and invisible soil (germs).
A thorough approach to sanitation will provide essential
cleanliness. It will assure an attractive appearance of
equipment, along with maximum efficiency and utility.
More importantly, a good sanitation program provides
one of the key elements in the prevention of
food-borne illnesses.
A controlled holding environment for prepared
foods is just one of the important factors involved in
the prevention of food-borne illnesses. Temperature
monitoring and control during receiving, storage,
preparation, and the service of food are of
equal importance.
A comprehensive sanitation program should focus on
the training of staff in basic sanitation procedures. This
includes personal hygiene, proper handling of raw foods,
cooking to a safe internal product temperature, and the
routine monitoring of internal temperatures from
receiving through service.
Most food-borne illnesses can be prevented through
proper temperature control and a comprehensive
program of sanitation. Both these factors are important
to build quality service as the foundation of customer
satisfaction. Safe food handling practices to prevent
food-borne illness is of critical importance to the health
and safety of your customers. HACCP, an acronym for
Hazard Analysis (at) Critical Control Points, is a quality
control program of operating procedures to assure food
integrity, quality, and safety. Taking steps necessary to
augment food safety practices are both cost effective and
relatively simple. While HACCP guidelines go far
beyond the scope of this manual, additional information
is available by contacting:
Center for Food Safety and Applied Nutrition
Food and Drug Administration
1-888-SAFEFOOD
INTERNAL FOOD PRODUCT TEMPERATURES
HOT FOODS
DANGER ZONE
40° TO 140°F
CRITICAL ZONE 70° TO 120°F
SAFE ZONE 1 4 0 ° T O 1 6 5 ° F
(4° TO 60°C)
(21° TO 49°C)
(60° TO 74°C)
COLD FOODS
DANGER ZONE
SAFE ZONE
ABOVE 40°F
36°F TO 40°F
(ABOVE 4°C)
(2°C TO 4°C)
FROZEN FOODS
DANGER ZONE
CRITICAL ZONE
SAFE ZONE
ABOVE 32°F
0° TO 32°F
0°F OR BELOW
(ABOVE 0°C)
(-18° TO 0°C)
(-18°C OR BELOW)
The most accurate method of measuring safe
temperatures of both hot and cold foods is by internal
product temperature. A quality thermometer is an
effective tool for this purpose and should be routinely
used on all products that require holding at a
specific temperature.
#825/33/37
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
7
SERVICE
THERMOSTAT/PILOT LIGHT SEQUENCE
THERMOSTAT CALIBRATION
Whenever the thermostat is turned “ON”, the indicator
light will indicate the power ON/OFF condition of the
heating cable, and consequently, the cycling of the
cabinet as it maintains the dialed cavity temperature. If
this light does not illuminate after normal start-up, the
main power source, thermostat, and/or light must be
checked. If the warming cabinet does not hold the
temperature as dialed, the calibration of the thermostat
must be checked. If the warming cabinet fails to heat or
heats continuously with the thermostat “OFF”, the
thermostat must be initially checked for proper
operation. If these items are checked and found to be in
order, a continuity and resistance check of the heating
cable should be made. SEE CIRCUIT DIAGRAM.
The thermostat is precision calibrated at the factory.
Normally, no adjustment or recalibration is necessary
unless the thermostat has been mishandled in transit,
changed or abused while in service. A thermostat with a
sensing bulb operates on hydraulic pressure,
consequently, any bending of the bulb results in a
change in its volume, and alters the accuracy of the
thermostat calibration.
A thermostat should be checked or recalibrated by
placing a quality, thermal indicator at the center of an
empty holding cavity. DO NOT CALIBRATE WITH
ANY FOOD PRODUCT IN THE CABINET. The
thermostat should be set, and should be allowed to
stabilize at that setting for a minimum of one hour.
Following temperature stabilization, the center of the
thermal swing of the air temperature within the
cabinet should approximately coincide with the
thermostat setting.
If calibration is necessary, the calibration screw should
be adjusted with great care. The calibration screw of the
thermostat is located in the thermostat dial shaft. With
the shaft held stationary, a minute, clockwise motion of
the calibration screw appreciably lowers the thermostat
setting. A reverse, or counter-clockwise motion
appreciably raises the thermostat setting. After
achieving the desired cycling of the thermostat, the
calibration screw must be sealed. Place a few drops of
enamel sealant directly on the calibration screw.
(Red nail polish or equivalent is acceptable.)
PG .
8
#825/33/37
INSTALLATION / OPERATION / SERVICE MANUAL
TROUBLE SHOOTING CHECKLIST
TROUBLE
POSSIBLE CAUSE
REMEDY
Unit does not operate.
Insufficient electric power unit.
Defective plug or cord.
Power switch defective.
Check power source.
Check and repair if necessary.
Replace.
Cooking temperature not correct.
Cook thermostat out of calibration.
Calibrate.
Holding temperature not correct.
Hold thermostat out of calibration.
Calibrate.
Timer runs down, but oven will not
go into HOLD.
Timer not de-energizing cook circuit.
Replace timer.
Cook thermostat erratic — will not
hold calibration.
Cook thermostat.
Replace thermostat.
Hold thermostat erratic — will not
hold calibration.
Hold thermostat.
Replace thermostat.
Oven goes from cooking
temperature to cold.
Hold thermostat.
Replace hold thermostat.
Oven will not go into cook cycle
when timer and cook thermostat
are ON.
Timer or contactor.
With timer turned ON, line
voltage should appear across
terminal 2 and 3 of timer. If not,
replace timer.
If line voltage does appear across
terminal 2 and 3 of timer, it should
also appear across holding coil
of contactor.
If line voltage does appear across
holding coil, and it won’t close its
contacts, replace contactor.
It takes too long to cook.
(Temperature O.K.)
Heating element open, resulting in
low wattage.
Cannot control temperature but
Heating element grounded.
thermostats check O.K. GENERAL HOLDING GUIDELINES
Replace element.
Replace element.
DISCONNECT THE UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING.
#825/33/37
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
9
S E R V I C E V I E W PA R T S L I S T
500-TH-II
11/5/99
PART DESCRIPTION
UNIT
ALTO-SHAAM
QUANTITY
PART NUMBER
PART DESCRIPTION
UNIT
QUANTITY
ALTO-SHAAM
PART NUMBER
1.
TOP ASSEMBLY
1
4131
25.
SIDE RACK
2
SR-2386
2.
TOP ASSEMBLY MOUNTING SCREWS
5
SC-2425
26.
SHELF
2
SH-2326
3.
TUBE TOP MOUNTING SCREWS
2
SC-2332
27.
DRIP PAN
1
14813
28.
HOLD THERMOSTAT
1
TT-3057
29.
COOK THERMOSTAT
1
TT-3329
4.
5.
6.
7.
TUBE BOTTOM MOUNTING SCREWS
2
SC-2425
BOTTOM FILLER (not shown)
1
1001
CAPILLARY GUARD MOUNTING SCREWS (not shown) 4
SC-2425
CAPILLARY GUARD (not shown)
2
GD-2450
CAPILLARY BULB MOUNTING SCREWS (not shown)
4
SC-2077
—125V
3
LI-3027
CAPILLARY BULB HOLD-DOWN (not shown)
4
BK-2609
—Red, 208-240V, 60 Hz
3
LI-3025
THERMOSTAT CAPILLARY BULB (not shown)
2
—
—White, 230V, 50 Hz
3
LI-3951
HOLD THERMOSTAT KNOB (Fahrenheit)
1
KN-3469
HOLD THERMOSTAT KNOB (Celsius)
1
KN-3474
COOK THERMOSTAT KNOB (Fahrenheit)
1
KN-3468
COOK THERMOSTAT KNOB (Celsius)
1
KN-3475
TIMER KNOB
1
—
TIMER NUT (not shown)
1
—
8.
SWITCH NUT
1
NU-2355
9.
CONTROL PANEL MOUNTING SCREWS
1
SC-2459
CONTROL PANEL MOUNTING SCREWS
5
SC-2425
30.
31.
32.
33.
34.
35.
10.
CONTROL PANEL
1
4700
11.
CONTROL CHASSIS MOUNTING SCREWS
4
SC-2459
12.
CONTROL CHASSIS
1
4146
13.
COVER PLATE (not shown)
3
1324
COVER PLATE MOUNTING SCREWS
6
SC-2459
37.
TUBE ASSEMBLY
1
—
38.
14.
15.
CASING ASSEMBLY
1
14688
16.
INSULATION TUBE MOUNTING SCREWS
6
SC-2459
17.
INSULATION TUBE ASSEMBLY (Left-hand)
1
14537
18.
INSULATION TUBE (Right-hand)
1
11073
19.
INSULATION: 25" x 100" (635mm x 2540mm)
1
IN-22364
20.
CABLE CONNECTION HARDWARE
21.
22.
23.
PG .
1
CB-3045
HEATING CABLE: 208-240V, Length 119' (36271mm) 1
HEATING CABLE: 125V, Length 99' (30175mm)
CB-3045
DOOR ASSEMBLY, RIGHT-HAND (Slab)
1
5146
DOOR ASSEMBLY, LEFT-HAND (Slab)
1
15520
DOOR ASSEMBLY, RIGHT-HAND (Window)
1
5235
DOOR ASSEMBLY, LEFT-HAND (Window)
1
15528
HINGE SET (1 pair of 2 hinges)
1
HG-2014
HINGE TO DOOR MOUNTING SCREWS (not shown)
6
SC-2072
6
SC-2073
DOOR HANDLE
1
HD-2566
DOOR HANDLE MOUNTING SCREWS (not shown)
4
SC-2073
DOOR CATCH MOUNTING SCREWS (not shown)
2
SC-2162
10
TIMER: 125V
1
TR-3504
TIMER: 208-240V—60 Hz
1
TR-3318
TIMER: 230V—50 Hz
1
TR-3402
POWER SWITCH: 125V, 208-240V, 60Hz
1
SW-3528
POWER SWITCH: 230V, 50 Hz
1
SW-3950
CONTACTOR: 125V
1
CN-3487
CONTACTOR: 208-240V-60 Hz, 230V-50 Hz ( TUV)
1
CN-3052
FILTER, LINE 230V ONLY
1
FI-33225
HOLDER, BIMET THERMOSTAT (not shown)
1
13958
THERMOSTAT HOLDER MTG. SCREWS
2
SC-2459
THERMOSTAT, HI LIMIT, RESET (not shown)
1
TT-33476
FAN: 125V
2
FA-3485
FAN: 208-240V
2
FA-3342
FAN BLADE
2
FA-3343
DOOR GASKET: Length 7' (2134mm)
1
GS-2398
CORD: 125V
1
CD-3397
CORDSET: 230V (Type HO7 RN-F)
1
CD-3922
39.
DRIP TRAY HOLDER
1
11535
40.
DRIP TRAY HOLDER MOUNTING SCREWS
3
SC-2425
41.
DRIP TRAY
1
11534
DISCONNECT OVEN FROM POWER
SOURCE BEFORE SERVICING
HINGE TO UNIT MOUNTING SCREWS (not shown)
24.
36.
CABLE AND POWER INDICATOR LIGHTS
#825/33/37
Cable Heating Service Kit
#4880
208-240V
#4879
125V
134 feet
112 feet
includes:
CB-3045
Cable Heating Element
CR-3226
Ring Connector
IN-3488
4
6
Insulation Corner
1 foot
1 foot
BU-3105
Shoulder Bushing
4
6
BU-3106
Cup Bushing
4
6
SL-3063
Insulating Sleeve
4
6
TA-3540
Electrical Tape
1 roll
1 roll
ST-2439
Stud 10-32
4
6
NU-2215
Hex Nut 10-32
8
12
INSTALLATION / OPERATION / SERVICE MANUAL
#825/33/37
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
11
S E R V I C E V I E W PA R T S L I S T
750-TH-II
5/1/01
PART DESCRIPTION
UNIT
ALTO-SHAAM
QUANTITY
PART NUMBER
PART DESCRIPTION
UNIT
QUANTITY
ALTO-SHAAM
PART NUMBER
1.
TOP ASSEMBLY
1
4174
26.
SHELF
3
SH-2324
2.
TOP ASSEMBLY MOUNTING SCREWS
5
SC-2425
27.
DRIP PAN
1
14831
3.
TUBE TOP MOUNTING SCREWS
2
SC-2332
28.
HOLD THERMOSTAT
1
TT-3057
29.
COOK THERMOSTAT
1
TT-3329
—125V
3
LI-3027
—Red, 208-240V, 60 Hz
3
LI-3025
—White, 230V, 50 Hz
3
LI-3951
TR-3504
4.
5.
TUBE BOTTOM MOUNTING SCREWS
2
SC-2425
BOTTOM FILLER (not shown)
1
1002
CAPILLARY GUARD MOUNTING SCREWS (not shown) 4
SC-2425
CAPILLARY GUARD (not shown)
2
GD-2450
CAPILLARY BULB MOUNTING SCREWS (not shown)
4
SC-2077
CAPILLARY BULB HOLD-DOWN (not shown)
4
BK-2609
THERMOSTAT CAPILLARY BULB (not shown)
2
—
HOLD THERMOSTAT KNOB (Fahrenheit)
1
KN-3469
HOLD THERMOSTAT KNOB (Celsius)
1
KN-3474
COOK THERMOSTAT KNOB (Fahrenheit)
1
KN-3468
COOK THERMOSTAT KNOB (Celsius)
1
KN-3475
TIMER KNOB
1
—
TIMER NUT (not shown)
1
—
8.
SWITCH NUT
1
NU-2355
9.
CONTROL PANEL MOUNTING SCREWS
1
SC-2459
CONTROL PANEL MOUNTING SCREWS
5
SC-2425
10.
CONTROL PANEL
1
4537
11.
CABLE COVER PLATE MOUNTING SCREWS
4
SC-2459
12.
CABLE COVER PLATE
2
1324
13.
TUBE ASSEMBLY
1
14.
CASING ASSEMBLY
1
6.
7.
35.
1
TR-3402
POWER SWITCH: 125V, 208-240V, 60 Hz
1
SW-3528
POWER SWITCH: 230V, 50 Hz
1
SW-3950
CONTACTOR: 125V
1
CN-3487
CONTACTOR: 208-240V-60 Hz, 230V-50 Hz (TUV)
1
CN-3052
FA-3485
FAN: 125V
2
FAN: 208-240V
2
FA-3342
FAN BLADE
2
FA-3343
VOLTAGE CONVERSION SWITCH
1
SW-3528
CD-3922
37.
DRIP TRAY HOLDER
1
11259
—
38.
DRIP TRAY HOLDER MOUNTING SCREWS
3
SC-2425
4601
39.
DRIP TRAY
1
11258
40.
FILTER, LINE, 230V ONLY
1
FI-33225
INSULATION TUBE (Left-hand)
1
4170
17.
INSULATION TUBE (Right-hand)
1
1163
18.
INSULATION: 25" x 120" (635mm x 3048mm)
1
IN-22364
19.
CABLE CONNECTION HARDWARE
1
CB-3045
HEATING CABLE: 208-240V, Length 189' (57607mm) 1
CB-3045
DOOR ASSEMBLY, RIGHT-HAND (Slab)
1
5178
DOOR ASSEMBLY, LEFT-HAND (Slab)
1
15538
DOOR ASSEMBLY, RIGHT-HAND (Window)
1
5452
DOOR ASSEMBLY, LEFT-HAND (Window)
1
5471
36.
TR-3318
TIMER: 230V—50Hz
CD-3397
16.
23.
34.
1
1
SC-2459
22.
33.
1
1
6
21.
32.
TIMER: 125V
TIMER: 208V, 240V—60 Hz
CORD: 125V
INSULATION TUBE MOUNTING SCREWS
HEATING CABLE: 125V, Length 95' (38956mm)
31.
CABLE AND POWER INDICATOR LIGHTS
CORDSET: 230V (Type HO7 RN-F)
15.
20.
30.
41.
42.
HOLDER, THERMOSTAT (not shown)
1
13958
HOLDER MTG. SCREWS
2
SC-2459
THERMOSTAT, HI LIMIT, RESET, 230V ONLY
1
TT-33476
BELL TIMER/KNOB FOR DELUXE MODELS ONLY (not shown) 1
TR-22388
DISCONNECT OVEN FROM POWER
SOURCE BEFORE SERVICING
Cable Heating Service Kit
HINGE SET (1 pair of 2 hinges)
1
HG-2014
includes:
HINGE TO DOOR MOUNTING SCREWS (not shown)
6
SC-2072
CB-3045
Cable Heating Element
HINGE TO UNIT MOUNTING SCREWS (not shown)
6
SC-2073
CR-3226
Ring Connector
IN-3488
DOOR HANDLE
1
HD-2566
DOOR HANDLE MOUNTING SCREWS (not shown)
4
SC-2073
DOOR CATCH MOUNTING SCREWS (not shown)
2
SC-2162
#4881
208-240V
#4879
125V
210 feet
112 feet
12
6
Insulation Corner
1 foot
1 foot
BU-3105
Shoulder Bushing
12
6
BU-3106
Cup Bushing
12
6
SL-3063
Insulating Sleeve
12
6
1 roll
1 roll
24.DOOR GASKET: Length 9' (2743mm)
1
GS-2398
TA-3540
Electrical Tape
25.
SIDE RACK
2
SR-2303
ST-2439
Stud 10-32
12
6
SIDE RACK FOR PAN SLIDE, 230V ONLY
2
14979
NU-2215
Hex Nut 10-32
24
12
PG .
12
#825/33/37
INSTALLATION / OPERATION / SERVICE MANUAL
#825/33/37
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
13
S E R V I C E V I E W PA R T S L I S T
1000-TH-II/SPLIT
9/26/02
1.
PART DESCRIPTION
UNIT
ALTO-SHAAM
QUANTITY
PART NUMBER
TOP ASSEMBLY
1
4200
2.
TOP ASSEMBLY MOUNTING SCREWS
5
SC-2425
3.
TUBE TOP MOUNTING SCREWS
2
SC-2332
4.
5.
6.
7.
PART DESCRIPTION
UNIT
QUANTITY
ALTO-SHAAM
PART NUMBER
25.
SIDE RACK
2
SR-2266
26.
SHELF
3
SH-2325
27.
DRIP PAN
1
14824
TUBE BOTTOM MOUNTING SCREWS
2
SC-2425
28.
HOLD THERMOSTAT
1
TT-3057
BOTTOM FILLER
1
1003
29.
COOK THERMOSTAT
1
TT-3329
CAPILLARY GUARD MOUNTING SCREWS (not shown)
4
SC-2425
30.
CAPILLARY GUARD (not shown)
2
GD-2450
—125V
3
LI-3027
CAPILLARY BULB MOUNTING SCREWS (not shown)
4
SC-2077
—Red, 208-240V, 60 Hz
3
LI-3025
CAPILLARY BULB HOLD-DOWN (not shown)
4
BK-2609
—White, 230V, 50 Hz
3
LI-3951
THERMOSTAT CAPILLARY BULB (not shown)
2
—
TIMER: 125V
1
TR-3504
HOLD THERMOSTAT KNOB (Fahrenheit)
1
KN-3469
TIMER: 208V, 240V—60 Hz
1
TR-3318
HOLD THERMOSTAT KNOB (Celsius)
1
KN-3474
TIMER: 230V—50Hz
1
TR-3402
COOK THERMOSTAT KNOB (Fahrenheit)
1
KN-3468
COOK THERMOSTAT KNOB (Celsius)
1
KN-3475
(not shown)
31.
32.
CABLE AND POWER INDICATOR LIGHTS
POWER SWITCH: 125V, 208-240V, 60 Hz
1
SW-3528
POWER SWITCH: 230V, 50 Hz
1
SW-3950
TIMER KNOB
1
—
TIMER NUT (not shown)
1
—
8.
SWITCH NUT
1
NU-2355
9.
CONTROL PANEL MOUNTING SCREWS
1
SC-2459
CONTROL PANEL MOUNTING SCREWS
5
SC-2425
FAN BLADE
CONTROL PANEL
1
4696
35.
VOLTAGE CONVERSION SWITCH
1
SW-3528
or CONTROL PANEL W/GAUGE
1
14089
36.
CORD: 125V
1
CD-3397
CORDSET: 230V (Type HO7 RN-F)
1
CD-3922
10.
33.
34.
CONTACTOR: 125V
1
CN-3487
CONTACTOR: 208-240V-60 Hz, 230V-50Hz (TUV)
1
CN-3052
FAN: 125 V
2
FA-3485
FAN: 208-240V
2
FA-3342
2
FA-3343
11.
CABLE COVER PLATE MOUNTING SCREWS
4
SC-2459
12.
CABLE COVER PLATE
2
1324
37.
DRIP TRAY HOLDER
1
1114
13.
TUBE ASSEMBLY
1
—
38.
DRIP TRAY HOLDER MOUNTING SCREWS
3
SC-2425
14.
CASING ASSEMBLY
1
4764
39.
DRIP TRAY
1
1113
CASING PLATE COVER
1
11900
CASING PLATE COVER MOUNTING SCREWS
2
SC-2459
40.
FILTER, LINE, 230V ONLY
1
FI-33225
41.
HOLDER, THERMOSTAT (not shown)
1
13958
HOLDER MTG. SCREWS
2
SC-2459
THERMOSTAT, HI LIMIT, RESET, 230V ONLY
1
TT-33476
15.
INSULATION TUBE MOUNTING SCREWS
6
SC-2459
16.
INSULATION TUBE ASSEMBLY (Left-hand)
1
14538
17.
INSULATION TUBE (Right-hand)
1
11074
18.
INSULATION: 25" x 120" (635mm x 3048mm)
1
IN-22364
19.
CABLE CONNECTION HARDWARE
20.
HEATING CABLE: 125V Length 90' (27432mm)
1
CB-3045
21.
22.
HEATING CABLE: 208-240V Length 183' (55778mm)
1
CB-3045
DOOR ASSEMBLY, RIGHT-HAND (Slab)
1
5204
DOOR ASSEMBLY, LEFT-HAND (Slab)
1
15557
DOOR ASSEMBLY, RIGHT-HAND (Window)
1
5527
DOOR ASSEMBLY, LEFT-HAND (Window)
1
5961
HINGE SET (1 pair of 2 hinges)
1
HG-2014
includes:
HINGE TO DOOR MOUNTING SCREWS (not shown)
6
SC-2072
CB-3045
Cable Heating Element
SC-2073
CR-3226
Ring Connector
IN-3488
Insulation Corner
HINGE TO UNIT MOUNTING SCREWS (not shown)
23.
24.
PG .
DISCONNECT OVEN FROM POWER
SOURCE BEFORE SERVICING
6
Cable Heating Service Kit
#4881
208-240V
#4879
125V
210 feet
112 feet
12
6
1 foot
1 foot
DOOR HANDLE
1
HD-2566
DOOR HANDLE MOUNTING SCREWS (not shown)
4
SC-2073
BU-3105
Shoulder Bushing
12
6
BU-3106
Cup Bushing
12
6
SL-3063
Insulating Sleeve
TA-3540
Electrical Tape
ST-2439
Stud 10-32
12
6
NU-2215
Hex Nut 10-32
24
12
DOOR CATCH MOUNTING SCREWS (not shown)
2
SC-2162
DOOR GASKET: Length 8' (2438mm)
1
GS-2398
14
#825/33/37
INSTALLATION / OPERATION / SERVICE MANUAL
12
6
1 roll
1 roll
#825/33/37
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
15
PG .
16
#825/33/37
INSTALLATION / OPERATION / SERVICE MANUAL
#825/33/37
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
17
PG .
18
#825/33/37
INSTALLATION / OPERATION / SERVICE MANUAL
#825/33/37
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
19
PG .
20
#825/33/37
INSTALLATION / OPERATION / SERVICE MANUAL
#825/33/37
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
21
T R A N S P O R TAT I O N
DAMAGE and CLAIMS
All Alto-Shaam equipment is
sold F.O.B. shipping point,
and when accepted by the
carrier, such shipments
become the property of
the consignee.
Should damage occur in shipment, it is a matter between the carrier
and the consignee. In such cases, the carrier is assumed to be
responsible for the safe delivery of the merchandise, unless
negligence can be established on the part of the shipper.
1. Make an immediate inspection while the equipment is still in
the truck or immediately after it is moved to the receiving area.
Do not wait until after the material is moved to a storage area.
2. Do not sign a delivery receipt or a freight bill until you have
made a proper count and inspection of all merchandise received.
3. Note all damage to packages directly on the carrier’s
delivery receipt.
4. Make certain the driver signs this receipt. If he refuses to sign,
make a notation of this refusal on the receipt.
5. If the driver refuses to allow inspection, write the following on
the delivery receipt:
Driver refuses to allow inspection of
containers for visible damage.
6. Telephone the carrier’s office immediately upon finding
damage, and request an inspection. Mail a written confirmation
of the time, date, and the person called.
7. Save any packages and packing material for further inspection
by the carrier.
8. Promptly file a written claim with the carrier and attach copies
of all supporting paperwork.
We will continue our policy of assisting our customers in collecting
claims which have been properly filed and actively pursued. We
cannot, however, file any damage claims for you, assume the
responsibility of any claims, or accept deductions in payment for
such claims.
L I M I T E D WA R R A N T Y
Alto-Shaam, Inc. warrants to the original purchaser that any original
part that is found to be defective in material or workmanship will, at
our option, subject to provisions hereinafter stated, be replaced with
a new or rebuilt part.
The labor warranty remains in effect one (1) year from installation or
fifteen (15) months from the shipping date, whichever occurs first.
The parts warranty remains in effect one (1) year from installation or
fifteen (15) months from the shipping date, whichever occurs first.
Exceptions to the one year part warranty period are as listed:
A. Halo Heat cook/hold ovens include a five (5) year parts
warranty on the heating element. Labor will be covered under
the terms of the standard warranty period of one (1) year or
fifteen (15) months.
B. Alto-Shaam Quickchillers include a five (5) year parts warranty
on the refrigeration compressor. Labor will be covered under
the terms of the standard warranty period of one (1) year or
fifteen (15) months.
This warranty does not apply to:
1. Calibration
2. Replacement of light bulbs and/or the replacement of display
case glass due to damage of any kind.
3. Equipment damage caused by accident, shipping, improper
installation or alteration.
4. Equipment used under conditions of abuse, misuse, carelessness
or abnormal conditions.
5. Any losses or damage resulting from malfunction, including loss
of product or consequential or incidental damages of any kind.
6. Equipment modified in any manner from original model,
substitution of parts other than factory authorized parts, removal
of any parts including legs, or addition of any parts.
This warranty is exclusive and is in lieu of all other warranties,
expressed or implied, including the implied warranties of
merchantability and fitness for purpose. In no event shall the
Company be liable for loss of use, loss of revenue, or loss of
product or profit, or for indirect or consequential damages. This
warranty is in lieu of all other warranties expressed or implied and
Alto-Shaam, Inc. neither assumes or authorizes any persons to
assume for it any other obligation or liability in connection with
Alto-Shaam equipment.
ALTO-SHAAM, INC.
Warranty effective January 1, 2000
Record the model and serial numbers of the unit for easy reference.
Always refer to both model and serial numbers in your
correspondence regarding the unit.
Model: _____________________________________________
Serial Number: _______________________________________
Purchased From: ______________________________________
Date Installed: ____________
Voltage: ________________
HALO HEAT COOK/HOLD/SERVE SYSTEMS BY
W164 N9221 Water Street
PHONE:
262.251.3 8 0 0
800.558.87 4 4 U . S . A ./ C A N A D A
●
®
P.O. Box 450 ● Menomonee Falls, Wisconsin 53052-0450 ● U.S.A.
FAX:
2 6 2 . 2 5 1 . 7 0 6 7 ● 8 0 0 . 3 2 9 . 8 7 4 4 U . S . A ./ C A N A D A
WEBSITE:
262.251.1907 INTERNATIONAL
W W W .alto-shaam.com
#825/33/37
INSTALLATION / OPERATION / SERVICE MANUAL
PRINTED IN U.S.A.