Table of contents
Getting started . . . . . . . . . . . . . . . . . . . . . 4
Parts checklist . . . . . . . . . . . . . . . . . . . . . 4
Installation . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing handset battery . . . . . . . . . . . . . . . 5
Low battery warning . . . . . . . . . . . . . . . . . . 6
Choose a location . . . . . . . . . . . . . . . . . . . 6
If you subscribe to DSL service . . . . . . . . . . . . 7
Connection . . . . . . . . . . . . . . . . . . . . . . 7
Removable handset and base plates . . . . . . . . . 8
Handset features . . . . . . . . . . . . . . . . . . . . . 9
Base features . . . . . . . . . . . . . . . . . . . . . . 10
Basic operation . . . . . . . . . . . . . . . . . . . . 11
Set handset ringer . . . . . . . . . . . . . . . . . . 11
Set date and time . . . . . . . . . . . . . . . . . . . 11
Telephone operation . . . . . . . . . . . . . . . . . . 12
Dial mode . . . . . . . . . . . . . . . . . . . . . . . 12
Temporary tone dialing . . . . . . . . . . . . . . . . 12
Language . . . . . . . . . . . . . . . . . . . . . . . 13
Operating range . . . . . . . . . . . . . . . . . . . 13
Displaying screen messages . . . . . . . . . . . . . 14
Speed dial . . . . . . . . . . . . . . . . . . . . . . . . 15
Store a speed dial entry . . . . . . . . . . . . . . . 15
Delete a speed dial entry . . . . . . . . . . . . . . . 17
Dial a speed dial number . . . . . . . . . . . . . . . 18
Re-assign speed dial locations . . . . . . . . . . . . 18
Directory . . . . . . . . . . . . . . . . . . . . . . . . . 19
Store a directory entry . . . . . . . . . . . . . . . . 19
Edit a directory entry . . . . . . . . . . . . . . . . . 21
Delete a directory entry . . . . . . . . . . . . . . . . 21
Dial a directory number . . . . . . . . . . . . . . . . 22
Move a directory entry to speed dial . . . . . . . . . 23
Caller ID . . . . . . . . . . . . . . . . . . . . . . . . . 24
Call log . . . . . . . . . . . . . . . . . . . . . . . . 24
Review call log . . . . . . . . . . . . . . . . . . . . 24
Remove records from call history . . . . . . . . . . 25
Dial a displayed number . . . . . . . . . . . . . . . 25
Store a call log entry in the directory . . . . . . . . . 25
Display screen messages . . . . . . . . . . . . . . 26
Ringer options . . . . . . . . . . . . . . . . . . . . . . 27
Headset operation . . . . . . . . . . . . . . . . . . . . 28
Belt clip . . . . . . . . . . . . . . . . . . . . . . . . 28
Additional information . . . . . . . . . . . . . . . . 29
Troubleshooting . . . . . . . . . . . . . . . . . . . . . 29
Maintenance . . . . . . . . . . . . . . . . . . . . . . . 36
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 36
Important safety instructions . . . . . . . . . . . . . . 37
FCC, ACTA and IC regulations . . . . . . . . . . . . . 38
The RBRC ® Seal . . . . . . . . . . . . . . . . . . . . 40
Technical specifications . . . . . . . . . . . . . . . . . 41
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
www.vtechphones.com
NEED HELP?
This manual has all the feature operations and troubleshooting you need to
install and operate your new VTech telephone. Please take the time to review
thoroughly to ensure proper installation of this VTech innovative and feature
rich product. You can also visit our website at www.vtechphones.com for
support, shopping, and everything new at VTech.
In Canada, please visit www.vtechcanada.com.
VTech toll free 1-800-595-9511
In Canada dial 1-800-267-7377
Before you begin
Parts checklist:
• Important!
Before using
this telephone,
you must read
Important
safety
instructions on
pages 37-38.
1. Base unit
2. Handset
3. Color handset brackets and
base plates
4. AC power adaptor
5. Belt clip
6. Telephone line cord
7. Battery
8. User’s manual
9. Battery compartment cover
To purchase replacement batteries,
visit us on the web at www.
vtechphones.com or call VTech
Communications, Inc. at 1-800595-9511. In Canada, contact
V Te c h Tele c o mmuni c ati o ns
Canada Ltd. at www.vtechcanada.
com or 1-800-267-7377.
1. Base unit
4. AC Power adaptor
7. Battery
www.vtechphones.com
2. Handset
5. Belt clip
3. Color handset brackets
and base plates
6.Telephone line cord
8. User’s manual
9. Battery compartment cover
1. Plug the battery connector securely into the jack inside the battery compartment according to the
color-coded label.
2. Insert battery in the center of the battery compartment.
3 Press down on the wired side until the battery securely snaps into place.
4. Neatly tuck the wires inside the battery compartment.
5. Position the battery compartment cover and slide it towards the unit until it clicks into place.
6. Put the handset in the base unit to start charging the new battery for at least 16 hours.
7. After the battery is fully charged, press ON on the handset and you should hear a dial tone.
���
��
��� �
�
�����
���
��� ��
�
www.vtechphones.com
• Use only the
VTech battery
and AC power
adaptor
supplied with
this telephone.
• Recharging of
a fully depleted
battery may take
up to 16 hours.
A fully charged
battery could
provide up to
5 hours of talk
time, or up to 5
days of standby
time.
• Place the
handset in the
base unit when
not in use to
ensure optimum
performance.
Getting started
Installation
Installing handset battery
Installation
Low battery warning
•If the phone will
not be used for
a long period of
time, remove the
battery to prevent
possible leakage.
•If you have any
trouble installing
your phone,
please refer to the
troubleshooting
section near the
end of this manual.
• Use only the
VTech battery and
AC power adaptor
supplied with this
telephone.
• if you need to
install your phone
within the same
room as other
cordless phones
or wireless
products, you may
need to select a
different channel
for your router
and or change the
channel on your
phone’s handsets.
When in low battery mode, the LOW BATTERY icon will be on and an alarm will sound until the
handset is returned to the base unit for recharging. LOW BATTERY will display on the handset when
the battery is low, depleted, or when there is no electrical contact between the battery and handset.
When the battery has been charged, these features will return to normal.
A low battery warning indicates one of the following:
1. There is no battery in your handset. The supplied battery must be installed in the handset.
2. The battery needs to be replaced, or
3. The battery is installed incorrectly. Re-install according to the instructions on page 5.
Choose a location
For optimum performance of your cordless telephone
system:
1.Choose a central location for your base unit.
2. Install your phone(s) as far away as possible from
any other cordless (wireless) device such as cordless
telephones, 802.11 wireless router (for example, WiFi).
3. Install your phone(s) as far away as possible from
other electronic equipment such as microwave ovens,
televisions, computers, etc.
4. Install your telephone equipment away from heat sources
and direct sunlight.
5.Avoid excessive moisture, dust or extreme cold.
www.vtechphones.com
Getting started
Installation
Connection
1. Choose a location for the base near an electrical outlet and telephone jack.
2. Plug the connector of the base power adaptor to the connector jack at the bottom of the base unit.
Then plug the adaptor into a standard electrical outlet (110V AC) not controlled by a wall switch.
3. Connect the telephone line cord to the jack at the bottom of the base unit, and the other end to
the wall jack.
If you subscribe to DSL service
If there is interference during telephone conversations and/or your caller ID features are not functioning
properly, install a noise filter to the telephone line between the base unit and the telephone wall jack.
Contact your DSL provider for a noise filter.
To power outlet
AC power adaptor
To single-line
telephone jack(RJ11C)
Telephone line cord
Noise filter (optional)
(For DSL users)
www.vtechphones.com
Installation
Removable handset and base
plates
Your phone comes with additional handset
brac ket s and base plates of var ious
colors. These brackets and plates are
interchangeable to suit your mood or room
decor.
Handset brackets
1. Carefully remove the handset ’s top
bracket and/or bottom bracket by pressing
inward towards the center of the phone,
then pull the bracket off slowly.
2. Attach the new top bracket and/or bottom
bracket by aligning the two sides of the
plate with the slots on the phone. Gently
push the brackets towards the center
of the phone until it locks securely into
place.
Base plate
1. Carefully remove the base plate by
inserting your thumb in the slot just below
the FIND HANDSET button and lift the
color plate from the base.
2. Align the tabs on the back of the new base
plate with the appropriate openings in the
base unit and then align the two front tabs
before snapping the plate into position.
www.vtechphones.com
1
2
1
2
Handset features
CHAN/REMOVE
• Switch to a clear channel while on a call.
• While handset is not in use, press and hold
to delete all records in the call log.
When viewing the call log, press to delete
the current record.
PROG
• Press to enter programming mode while
the handset is idle (off).
SELECT
• Press to store a programming option, or to store a directory entry.
( /DIR VOL+)
• When the phone is not in use, press
to display directory entries.
• Press & hold for 2 seconds during
idle mode to adjust ringer volume.
A double beep will sound when the
highest setting is reached.
• During a call, press to increase
listening volume. A double beep will
sound when the highest setting is
reached.
OFF
• During a call, press to hang up.
• While the handset is ringing, press
to silence the ringer.
• Press and hold for two seconds
while in idle mode to erase the
MISSED CALLS display.
• During programming, press to exit
without making changes.
REDIAL/PAUSE
• Press TALK, then press this button
to call the last number dialed.
-OR Press this button, then press TALK
to call the last number dialed.
• While handset is not in use, press
this button twice to delete the last
number dialed from this telephone.
• While dialing or entering numbers
into the directory, press to insert a
four-second dialing pause.
www.vtechphones.com
Basic operation
(CID/VOL-)
• When the phone is not in use, press to
display caller ID information.
• Press and hold for two seconds while in idle
mode to adjust ringer volume. A double beep
will sound at the lowest setting.
• During a call, press to lower listening volume. A double beep will sound at the lowest
setting.
TALK
• Press this button before dialing the number
to make a call.
-OR Dial the number (use
to backspace and
correct digits), then press this button to
make a call.
• Press any key except OFF, CID/VOL-,
DIR/VOL+ to answer a call.
• While on a call, when there is a call waiting
alert, press this button to take the new call,
then press this button again to return to the
original call.
• When the phone is in use, this button will
glow steadily.
Base features
CHARGE/IN USE Indicator
FIND HANDSET
Press to page the handset for up to 60 seconds.
Press again, press OFF, or place the handset in
its base to cancel the page.
10
• Flashes when the handset is in use.
• Flashes in unison with incoming ringing.
• Flashes when the battery is low, depleted, or when
there is no electrical contact between the battery and
the handset.
• On steadily when the handset is charging in the base.
www.vtechphones.com
Telephone operation
Set handset ringer
�������������
•If you set the
ringer volume to
OFF, the phone
will not ring during
an incoming call
but the CHARGE/
IN USE indicator
will flash.
Basic operation
You can select from four traditional ringers, thirteen musical ringers, or turn the ringer OFF.
1. Make sure the handset is idle (off).
2. Press PROG.
3. Press until the screen displays RINGER: and the current setting.
4. Press SEL. The current setting blinks, and you will hear a sample of the ring tone.
5. Press or to hear a sample of each ring tone.
6. Press SEL to choose the desired ring tone. If you chose a musical ringer or one of your personal
ring tones, the handset will display, for example:
�����������
7. Press or to adjust the volume level.
8. Press SEL to confirm the volume setting. A confirmation tone will sound. To set ringer volume,
press and hold CID/VOL- or DIR/VOL+ keys.
Set date and time
If you subscribe to caller ID service, the date and time will be set automatically with the first incoming
call. If you do not have caller ID service, the date and time can be set manually:
1. Make sure the handset is idle (off).
2. Press PROG.
3. Press until the screen displays DATE/TIME.
4. Press SEL. The current month blinks.
5. Use
or to adjust the month, then press SEL.
6. Repeat step 5 to adjust the day, hour, minute and
or (to indicate am or pm). You’ll hear a
confirmation beep.
www.vtechphones.com
BASIC OPERATION
11
Telephone operation
Dial mode (preset to tone)
If you have touch tone service, the phone is ready to use as soon as the battery is charged.
If you have pulse (rotary) service, the dial mode must be changed.
1. Make sure the handset is idle (off).
2. Press PROG.
3. Press until the screen displays DIAL MODE: and the current setting.
4. Press SEL. The current setting blinks.
5. Press or . The screen displays TONE or PULSE.
6. Press SEL to save. You’ll hear a confirmation beep.
Temporary tone dialing
If you have pulse (rotary) service, you can change from pulse to touch tone dialing during a call by
pressing *TONE. This is useful if you need to send touch tone signals for access to telephone banking
or long distance services.
1. Dial the number.
2. Press *TONE. Buttons pressed after this send touch tone signals.
3. After you hang up, the phone automatically returns to pulse dial service.
Language
You can select English, Spanish or French.
1. Make sure the handset is idle (off).
2. Press PROG.
3. Press or until the screen displays LANGUAGE.
4. Press SEL. The current setting blinks.
5. Press
or to select among ENGLISH, SPANISH or FRENCH. When the desired language is
displayed, press SEL or PROG. A confirmation tone will sound.
12
www.vtechphones.com
Telephone operation
Operating range
www.vtechphones.com
Basic operation
This cordless telephone operates within the maximum power allowed by the Federal Communications
Commission (FCC). Even so, this handset and base can communicate over only a certain distance
— which can vary with the locations of the base and the handset, the weather, and the construction
of your home or office.
If the handset receives a call while out of range, the handset might not ring — or if it does ring,
the call might not connect well when you press TALK. Move closer to the base, then press TALK
to answer the call.
If the handset is moved out of range during a phone conversation, there might be interference.
To improve reception, move closer to the base.
If the handset moves out of range without your pressing OFF, the phone will be left off the hook.
To hang up properly, walk back within range, periodically pressing OFF.
13
Telephone operation
Displaying screen messages
14
Screen displays:
When:
** RINGING **
There is a call coming in.
CONNECTING...
The handset is waiting for a dial tone.
PHONE
The handset is in use.
** PAGING **
The base is paging the handset.
LOW BATTERY
The battery needs to be recharged.
SCANNING...
The handset is changing to one of the 30 channels available for better
reception.
CAN’T CONNECT
Together with an error tone when the base power is off and TALK is
pressed.
Displays when handset is out of range and an attempt to dial failed.
NEW VOICE MAIL
There are telephone company voicemail.
www.vtechphones.com
Speed dial
You can store as many as nine frequently dialed telephone numbers with names (up to 15 characters
and 24 digits in each location) into the speed dial memory locations you assign in the handset.
Store a speed dial entry
Dial Key
1
2
3
4
5
6
7
8
9
0
*
#
Once
Twice
Presses
3 Times 4 Times 5 Times 6 Times
1
A
B
C
2
D
E
F
3
G
H
I
4
J
K
L
5
M
N
O
6
P
Q
R
S
T
U
V
8
W
X
Y
Z
9
‘
,
-
.
7
0
*
&
www.vtechphones.com
#
15
Basic operation
1. Press PROG.
2. Press or until the screen displays SPEED DIAL.
3. Press SEL. The screen displays ENTER 1-9.
4. Press the key (1 through 9) for the memory location for the new entry.
The screen displays ENTER NAME.
5. Using the chart below, enter up to 15 characters for the name to be stored with the
number. Use to backspace and make corrections; use to advance or add a space.
6. When finished entering the name, press SEL or PROG. The screen displays ENTER
NUMBER.
• The entries stored in
speed dial memory
will be marked 1
through 9 in the
telephone directory.
• Press OFF anytime
to exit the speed dial
mode.
• When the memory
is full, the screen
displays MEMORY
FULL, an error
tone sounds and no
new entry can be
stored until an entry
is deleted from the
speed dial memory
or the telephone
directory.
• Take caution when
assigning speed dial
location numbers
in memory. If the
location already
has an entry stored,
the new entry
will overwrite the
existing one. Be
careful not to save
over entries you do
not wish to delete
from memory.
Speed dial
• When an incoming
phone number
matches an
existing number
in the directory
or speed dial, the
stored name will
be displayed on
the screen.
16
7. Enter the telephone number. Use
to backspace and make a correction. Press REDIAL/PAUSE
to store a pause in the dialing sequence.
-OR Press REDIAL/PAUSE to display the last number dialed.
8. Press SEL or PROG. The screen displays DISTINCT RING? and the current setting.
9. Press or
to change the setting. Choose Y (for yes) if you wish the phone to alert you to calls
from this number by changing to a distinctive ring tone after the first or second ring. Choose N for
a normal ring tone.
10. Press SEL or PROG to confirm your selection.
If you chose Y, the screen displays:
������� ����
If N is chosen, skip to Step 12.
����������
11.The ringer name will blink. Press
or
for the desired ring
��
tone.
12. Press SEL or PROG to confirm your selection.
www.vtechphones.com
Speed dial
Edit a speed dial entry
����������������
����������
��
Basic operation
1. Press and hold the memory location key (1 through 9) of the entry
to be edited.
2. When the screen displays the desired number, press SEL. Then
press or until EDIT flashes, Press SEL.
3. The screen displays the name and number. The cursor appears
at the end of the name. Use or and the dial pad keys to edit
the name. Press SEL to move to edit the number. Press SEL to
continue and edit the distinct ring tone. Follow steps 9 through
12 in Store a speed dial entry.
Delete a speed dial number
1. Press and hold the memory location key (1 through 9) of the entry
to be deleted.
2. When the screen displays the number to be deleted, press SEL.
Then press or
until ERASE flashes.
3. Press SEL. The screen displays ERASE NO YES and the number.
The current choice flashes.
4. Press or until YES flashes.
5. Press SEL. A confirmation tone will sound.
����������������
����������
��
www.vtechphones.com
17
Speed dial
Dial a speed dial number
1. Press and hold the memory location key (1 through 9) of the
entry you wish to dial.
2. Press TALK to dial the displayed memory number.
Re-assign speed dial locations
1. Press and hold the memory location key (1 through 9) of the
entry you wish to reassign.
2. When the screen displays the number you want to reassign,
press SEL. Then press
or
until SPEED flashes.
3. Press SEL. The screen displays ENTER 1-9 and the
number.
4. Press the keys (1 through 9) to re-assign this entry into another
memory location. A confirmation tone will sound.
18
www.vtechphones.com
����������������
����������
��
Directory
Your phone can store 20 telephone numbers with names (including nine speed dial entries), each
up to 15 characters for the name and 24 digits for the number.
Store a directory entry
1. Press PROG. The screen displays DIRECTORY.
2. Press SEL. The screen displays ENTER NAME.
3. Using the chart below, enter up to 15 characters for the name to be stored with the number. Use
to backspace and make corrections, and to advance or add a space.
Once
Twice
Press
3 times
4 times
5 times
Basic operation
Dial key
1
2
3
4
5
6
7
8
9
0
*
#
• Press OFF
anytime to exit
directory.
6 times
1
A
B
C
2
D
E
F
3
G
H
I
4
J
K
L
5
M
N
O
6
P
Q
R
S
T
U
V
8
W
X
Y
Z
9
‘
,
-
.
7
0
*
&
#
4. When finished entering the name, press SEL or PROG. The screen displays ENTER
NUMBER.
5. Enter the telephone number. Use to backspace and make corrections. Press REDIAL/PAUSE
to store a pause in the dialing sequence.
www.vtechphones.com
19
Directory
• If you choose N,
skip to Step 10.
20
-OR Press REDIAL/PAUSE to display the last number dialed from this phone.
6. Press SEL or PROG. The screen displays DISTINCT RING? and the current setting.
7. Press or to change the setting. Choose Y (for yes) if you wish the phone to alert you to calls
from this number by changing to a distinct ring tone after the first or second ring. Choose N for a
normal ring tone.
8. Press SEL or PROG to confirm your selection.
If you choose Y, the screen displays:
If N is chosen, skip to Step 12.
������� ����
9. The ring tone name will blink. Press or for the
����������
desired ring tone.
��
10. Press SEL or PROG to confirm your selection.
www.vtechphones.com
Directory
Edit a directory entry
1. Press . The screen displays DIRECTORY.
2. Press or to scroll alphabetically through the entries.
-OR Press the dial pad key for the first letter of the entry to be edited.
3. When the screen displays the desired entry, press SEL. Then press
until EDIT flashes.
����������������
4. Press SEL. The screen displays the name and number. The cursor appears at the end of the
name. Use , and the dial pad keys to edit the name. Press SEL to move on to edit the number.
Use to backspace and make corrections. Press SEL to move on to edit the distinct ring tone.
Follow steps 7 through 9 in Storing an Entry in the Directory.
Delete a directory entry
1. Press until the screen displays DIRECTORY.
2. Press or to scroll alphabetically through entries.
-OR Press the dial pad key for the first letter of the entry to be deleted.
3. When the screen displays the desired entry, press SEL. Then press
until ERASE flashes.
www.vtechphones.com
21
Basic operation
����������
• When memory is
full, the screen
displays MEMORY
FULL; an error
tone sounds, and
no new entry can
be stored until an
existing entry is
deleted.
Directory
����������������
����������
4. Press SELECT. The screen displays ERASE NO YES and the number. The current setting
flashes.
5. Press until YES flashes.
6. Press SEL. You will hear a confirmation beep.
Dial a directory number
1. Press . The screen displays DIRECTORY.
2. Press or to scroll alphabetically through the entries.
-OR Press the dial pad key for the first letter of the entry to be dialed.
3. Press TALK to dial the displayed directory number.
22
www.vtechphones.com
Directory
Move a directory entry to speed dial
1. Press . The screen displays DIRECTORY.
2. Press or to scroll alphabetically through the directory.
-OR Press the dial pad key for the first letter of the entry to be
moved.
3. When the screen displays the entry to be moved, press SEL.
Then press until SPEED flashes.
����������������
Basic operation
����������
4. Press SEL. The screen displays ENTER 1-9 and the
number.
5. Press the key (1 through 9) to move this entry from the
directory into speed dial and assign it to memory. A
confirmation tone will sound. A location number (1 through
9) will be displayed with this entry.
www.vtechphones.com
23
Caller ID
• When repeat
caller ID (CID)
data arrives, the
newest date,
time and caller
ID information
overwrite the
old information,
and is displayed
during CID
review.
• Press OFF
anytime to exit
call log.
����������������
���������������
����
Call log
When the memory is full, the oldest call information is deleted to make room for new incoming call
information. For each incoming call, the screen displays the following information between the first
and second rings:
• The caller’s name (up to 15 letters are sent by your telephone company).
• The caller’s area code and telephone number (up to 11 digits).
• The time and date of the call.
• The repeat Tag (
) in the upper right corner, indicating this party has called more than once.
Review call log
1. Press to view call log.
2. Use or to scroll through entries in the call log. Press
Press to scroll up towards newer entries.
24
www.vtechphones.com
to scroll down towards older entries.
Caller ID
Remove records from call history
Basic operation
Remove a specific entry:
1. Locate the record to be deleted from the call log.
2. Press CHAN/REMOVE, a confirmation tone will sound.
Remove all entries:
1. With the Handset in idle (off) mode, press and hold CHAN/REMOVE. The screen displays ERASE
ALL NO YES. The current choice flashes.
2. Pres until YES flashes.
3. Press SEL. A confirmation tone will sound.
Dial a displayed number
1. Locate the desired record in the call log.
2. If you wish to change how the number is dialed, press #. The
screen displays all dialing sequences available for this entry
(1 + area code + number; area code + number; number only;
1+ number). The dialing options are:
3. Press SEL. Press until DIAL flashes.
4. Press SEL again. The number is automatically dialed.
-OR When the number is correctly displayed for dialing, press TALK.
595-9511
1-595-9511
800-595-9511
1-800-595-9511
Store a call log entry in the directory
1. Locate the desired entry in the call log to be stored in the directory.
2. If you wish to change how the number is stored, press #. The screen displays all dialing
sequences available for this entry (area code + number; 1 + area code + number; number only;
1 + number).
3. Press SEL, then press until PROGRAM flashes.
www.vtechphones.com
25
Caller ID
• When the
memory is full, the
screen displays
MEMORY FULL,
an error tone
sounds and no
new number can
be stored unti an
existing entry is
deleted.
DIAL
PROGRAM
800-595-9511
OLD
28 5/01 5:40PM
4. Press SEL. The screen displays the number and name. The cursor appears at the end of the name.
Use , and the dial pad keys to edit the name. Press SEL to continue and edit the number. Use
to backspace and make corrections. Press SEL to confirm.
5. Follow steps 7 through 9 in Store a directory entry on page 19.
Display screen messages
26
Screen displays:
When:
PRIVATE
The other party is blocking name and/or number
information.
UNKNOWN
Your phone company is unable to receive
information about this caller’s name and/or
number.
* (after name)
This caller has called you more than once.
www.vtechphones.com
Ringer options
In addition to four traditional ringer options and ringer off, your gz2336 handset has thirteen
popular pre-programmed ring tones.
Traditional Ring Options:
Ringer 1
Ringer 2
Ringer 3 Ringer 4
Tones:
Ringer OFF
2. Siren
4. Hip-Hop
6. Rock
8. Fur Elis
10. T March
12. Joy
www.vtechphones.com
Basic operation
1. Rotary
3. Bark
5. Metal
7. Monster
9. Num 40
11. Charge
13. B_Day
27
Headset operation
• Whenever a
compatible
headset is
connected to the
cordless handset,
the microphone
on the handset
will be muted to
alleviate the effect
of background
noise.
Your phone handset is equipped with a 2.5mm headset jack for use with an optional accessory headset
for handsfree operation.
If you’ve purchased the VTech gz2336 and wish to
obtain a compatible headset, you must purchase it
separately. To purchase a headset, visit us on the
web at www.vtechphones.com or call VTech Customer Service at 1-800-595-9511.
Once you have a compatible 2.5mm headset, locate
the headset jack on the side of the handset. Connect
the plug on the headset cord to the jack (under a
small rubber flap) on the cordless handset. The plug
should fit securely. Do not force the connection.
Belt clip
Your phone is also equipped with a detachable belt
clip. Align the pins on the inside edge of the clip with
the notches on the sides of the handset. The belt
clip should snap securely into place. Do not force the
connection.
28
www.vtechphones.com
Troubleshooting
If you have difficulty operating your phone, the suggestions below should solve the problem. If you still have difficulty after
trying these sug­gestions, call VTech Communications at 1-800-595-9511. In Canada, call VTech Telecommunications
Canada Ltd. at 1-800-267-7377.
Suggestion
My phone doesn’t
work at all.
• Make sure the power adaptor is plugged in.
• Make sure the telephone line cord is plugged firmly into the base unit and the telephone wall
jack.
• Disconnect the power adaptor for a few minutes, and then reconnect it.
• Charge the battery in the handset for at least 16 hours. For optimum daily performance, return
the handset to its base when not in use.
• Reset the base. Unplug the unit’s electrical power. Wait for 15 seconds then plug it back in.
Allow up to one minute for the handset and base to reset.
• You may need to purchase a new battery, please refer to the battery sections in this user’s
manual.
I cannot get a dial
tone.
•
•
•
•
Try all the suggestions above.
Move the handset closer to the base. You might have moved out of range.
Your line cord might be malfunctioning. Try installing a new line cord.
If the previous suggestions do not work, disconnect the base unit from the telephone jack and
connect a different phone. If there is no dial tone on that phone either, the problem is in the
wiring or local service. Contact your local telephone company.
www.vtechphones.com
29
Additional information
Problem
Troubleshooting
Problem
Suggestion
I cannot dial out.
• Make sure there is a dial tone before dialing. It is normal for handset to take a second or two
to find the base and produce a dial tone. Wait an extra second before dialing.
• Make sure the phone is set to the correct dial mode for the type of service that you have (pulse
or touchtone). Refer to the Installation section of this user’s manual to set the dial mode.
•If the other phones in your home are having the same problem, the problem is in your wiring
or local service. Contact your local telephone company.
• Eliminate any background noise. Noise from a television, radio or other appliance may cause
the phone not to dial out properly. If you cannot eliminate the background noise, first try muting
the handset before dialing, or dialing from another room in your home with less background
noise.
My handset beeps
five times and isn’t
performing normally.
• Make sure the power adaptor is securely plugged into the base. Plug the unit into a different,
working outlet not controlled by a wall switch.
• Move the handset closer to the base. It might have been moved out of range.
•If the handset is in its base and the charging light does not light, refer to Charge Light is Off
in this troubleshooting guide.
• Reset the base. Unplug the unit’s electrical power. Wait for 15 seconds then plug it back in.
Allow up to one minute for the handset and base to reset.
•Other electronic products can cause interference with your cordless phone. Try installing
your phone as far away from these types of electronic devices as possible: wireless routers,
radios, radio towers, pager towers, cell phones, intercoms, room monitors, televisions, personal
computers, kitchen appliances and other cordless phones.
30
www.vtechphones.com
Troubleshooting
Suggestion
CAN’T CONNECT
displays on my
handset.
• Move the handset closer to the base. You might have moved out of range.
• If the handset is in its base and the charging light does not light, refer to the charge light is off
in this troubleshooting guide.
• Reset the base. Unplug the unit’s electrical power. Wait for 15 seconds then plug it back in.
Allow up to one minute for the handset and base to reset.
• Other electronic products can cause interference with your cordless phone. Try installing
your phone as far away from these types of electronic devices as possible: wireless routers,
radios, radio towers, pager towers, cell phones, intercoms, room monitors, televisions, personal
computers, kitchen appliances and other cordless phones.
The battery does not
hold a charge.
• Charge the battery in the handset for at least 16 hours. For optimum daily performance, return
the handset to its base when not in use.
• You may need to purchase a new battery, please refer to the battery sections in this user’s
manual.
• Your phone might be malfunctioning. Please refer to the Warranty section of this user’s manual
for further instruction.
If you subscribe to DSL
service
If you hear noise during conversations and/or your caller ID features are not functioning properly,
install a noise filter to the telephone line between the base unit and the telephone line jack. Contact
your DSL provider to obtain a noise filter.
My Caller ID isn’t
working.
•Caller ID is a subscription service. You must subscribe to this service for this feature to work
on your phone.
• Your caller must be calling from an area that supports caller ID.
• Both you and your caller’s telephone companies must use caller ID compatible equipment.
www.vtechphones.com
31
Additional information
Problem
Troubleshooting
Problem
Suggestion
I get noise, static,
or weak signal even
when I’m near the
base.
• Other cordless phones and 802.11 wireless routers that are used for home computer networks both
use internal radios to communicate. The radios may interfere with one another. You can improve the
performance of your cordless phones and your router by:
a. positioning your new phone as far away as possible from any other existing cordless telephone system that is already installed in your home to avoid the two systems interfering with each other.
b. positioning your telephone base as far as possible from your router, computer or any other computer devices.
c. selecting channels four through 10 for your router (refer to your router’s user manual for more information).
d. If you still have problems with the phone or the router, make sure the handset is ON and press
CHAN until the performance improves.
• Press the CHAN button while on a call until the interference has been eliminated.
• Other electronic products can cause interference with your cordless phone. Try installing your phone
as far away from these types of electronic devices as possible: wireless routers, radios, radio towers,
pager towers, cell phones, intercoms, room monitors, televisions, personal computers, kitchen
appliances and other cordless phones.
• Microwaves operate on the same frequency as your phone. It is normal to experience static on
your phone while the microwave is running. Do not install this phone in the same outlet or near the
microwave.
•If your phone is plugged in with a modem or surge protector, plug the phone (or modem/surge
protector) into a different location. If this solves the problem, re-locate your phone or modem farther
apart from one another, or use a different surge protector.
• Relocate your phone to a higher location. The phone will likely get better reception not installed in
a low area.
• If the other phones in your home are having the issue, the problem is in your wiring or local service.
Contact your local telephone company (charges may apply.)
I hear other calls while
using my phone.
• Disconnect your base unit from the telephone jack, and plug in a regular telephone. If you
still hear other calls, the problem is probably in your wiring or local service. Call your local
telephone company.
32
www.vtechphones.com
Troubleshooting
Suggestion
I hear noise in the
handset, and none of
the keys or buttons
work.
• Make sure the power cord is plugged in.
My handset does not
ring when I receive
a call.
• Make sure you have the ringer activated. Refer to the section(s) on ringer selection in this
user’s manual.
•Make sure the telephone line cord is plugged firmly into the base unit and the telephone jack.
Make sure the power cord is plugged in.
• You may be too far from the base unit.
• Charge the battery in the handset for 16 hours. For optimum daily performance, return the
handset to its base when not in use.
• You may have too many extension phones on your telephone line to allow all of them to ring.
Try unplugging some of the other phones.
• The layout of your home or office might be limiting the operating range. Try moving the base
to another location, preferably on an upper floor.
• If the other phones in your home are having the issue, the problem is in your wiring or local
service. Contact your local telephone company (charges may apply.)
• Test a working phone at the phone jack. If another phone has the same problem, the problem
is the phone jack. Contact your local telephone company (charges may apply.)
• Other electronic products can cause interference with your cordless phone. Try installing
your phone as far away from these types of electronic devices as possible: wireless routers,
radios, radio towers, pager towers, cell phones, intercoms, room monitors, televisions, personal
computers, kitchen appliances and other cordless phones
• Your line cord might be malfunctioning. Try installing a new line cord.
www.vtechphones.com
33
Additional information
Problem
Troubleshooting
Problem
Suggestion
My calls fade or cut in
and out while I’m using
my handset.
• Press the CHAN button while on a call until the interference has been eliminated.
• Other electronic products can cause interference with your cordless phone. Try installing
your phone as far away from these types of electronic devices as possible: wireless routers,
radios, radio towers, pager towers, cell phones, intercoms, room monitors, televisions, personal
computers, kitchen appliances and other cordless phones
• Microwaves operate on the same frequency as your phone. It is normal to experience static
on your phone while the microwave is running. Do not install this phone in the same outlet or
near the microwave.
• If your phone is plugged in with a modem or surge protector, plug the phone (or modem/surge
protector) into a different location. If this solves the problem, re-locate your phone or modem
farther apart from one another, or use a different surge protector.
• Relocate your phone to a higher location. The phone will get better reception not installed in
a low area.
• If the other phones in your home are having the issue, the problem is in your wiring or local
service.
The charge/in use light
is off.
• Clean the handset and base charging contact each month using a pencil eraser or cloth.
• Make sure the power and line cords are plugged in correctly and firmly.
• Reset the base. Unplug the unit’s electrical power. Wait for 15 seconds then plug it back in.
Allow up to one minute for the handset and base to reset.
• Your phone might be malfunctioning. Please refer to the Warranty section of this user’s manual
for further instruction.
34
www.vtechphones.com
Troubleshooting
Problem
Suggestion
The charge/in use light
is flashing.
This is an indication that the battery is low, depleted, or that there is no electrical contact between
the battery and the base unit. Ensure the battery is securely plugged into the handset. Close
the battery compartment cover and place the handset in the base unit and let it charge until the
battery is fully charged (see page 5.)
Common cure for
electronic equipment.
If the unit does not seem to be responding normally, then try putting the handset in its base. If it
does not seem to respond, do the following (in the order listed):
1. Disconnect the power to the base.
2. Disconnect the handset battery, and spare battery, if applicable.
3. Wait a few minutes.
4. Connect power to the base.
5. Re-install the battery(ies).
6. Wait for the handset to re-establish its link with the base. To be safe, allow up to one minute
for this to take place.
35
Additional information
www.vtechphones.com
Maintenance
Taking care of your telephone
Your cordless telephone contains sophisticated electronic parts, so it must be treated with care.
Avoid rough treatment
Place the handset down gently. Save the original packing materials to protect your telephone if you ever need to ship it.
Avoid moisture
Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or handle it with wet hands. Do not install your base unit near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety, use caution when using electric appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a soft cloth slightly dampened with water or a mild soap. Do not use excess water or
cleaning solvents of any kind.
emember that electrical appliances can cause serious injury if used when you are wet or standing in water. If your base unit should fall into water, DO NOT RETRIEVE IT UNTIL YOU
R
UNPLUG THE POWER CORD AND TELEPHONE LINE CORDS FROM THE WALL. Then pull the unit out by the unplugged cords.
Warranty
What does this limited warranty cover?
•The manufacturer of this VTech product, VTech Communications, warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the product and all accessories provided by
VTech in the sales package (“Product”) are free from material defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in
accordance with operation instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America.
What will VTech Communications do if the Product is not free from material defects in materials and workmanship during the limited warranty period (“Materially Defective Product”)?
•
During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option, without charge, a Materially Defective Product. If we repair this product, we may use new or refurbished replacement parts. If we choose to replace this product, we may replace it with a new or refurbished product of the same or similar design. VTech will return repaired or replacement products to you in working condition. VTech will retain defective parts, modules, or equipment. Repair or replacement of Product, at VTech’s option, is your exclusive remedy. You should expect the repair or replacement to take approximately 30 days.
How long is the limited warranty period?
•
The limited warranty period for the product extends for ONE (1) YEAR from the date of purchase if we repair or replace a Materially Defective Product under the terms of this limited warranty. This limited warranty also applies to repaired or replacement Products for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover
1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service representative of VTech; or
3.Product to the extent that the problem experienced is caused by signal conditions, network reliability or cable or antenna systems; or
4. Product to the extent that the problem is caused by use with non-VTech electrical accessories; or
36
www.vtechphones.com
Warranty
5.Product whose warranty/quality stickers, Product serial numbers plates or electronic serial numbers have been removed, altered or rendered illegible; or
6.Product purchased, used, serviced, or shipped for repair from outside the United States, or used for commercial or institutional purposes (including but not limited to Products used for rental
purposes ); or
7. Product returned without valid proof of purchase (see 2 below); or
8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.
How do you get warranty service?
• To obtain warranty service in the United States of America, call 1-800-595-9511 for instructions regarding where to return the Product. Before calling for service, please check the user’s manual. A check of the Product controls and features may save you a service call.
•Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport
of Product (s) to the service location. VTech will return repaired or replaced product under this limited warranty to you, transportation, delivery or handling charges prepaid. VTech assumes
no risk for damage or loss of the Product in transit.
•
If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difficulty;
2. Include “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
Other Limitations
• This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this product. The warranty exclusively describes all of VTech’s responsibilities regarding the product. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you should not rely on any such modification.
State Law Rights: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
imitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the product is fit for ordinary use) are limited to one year from
L
date of purchase. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
• In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the product, or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3.Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water (for example, near a bath tub, kitchen sink or swimming pool).
5.Do not place this product on an unstable surface, such as a table, shelf or stand. The product may fall, causing serious damage.
6.Slots and openings in the back or bottom of the base unit and handset are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the
www.vtechphones.com
37
Additional information
Important safety instructions
Important safety instructions
product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This product should not be placed in any area where proper
ventilation is not provided.
7.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power
company.
8.Do not allow anything to rest on the power cord. Do not install this product where the cord may have anyone walking on it.
9.Never push objects of any kind into this product through slots in the base or handset as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock.
Never spill liquid of any kind on the product.
10.To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the base or handset other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.
11.Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
12.Unplug this product from the wall outlet and refer servicing to an authorized service facility under the
following conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled onto the product.
C. If the product has been exposed to rain or water.
D.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of
other controls may result in damage and often requires extensive work by an authorized technician to restore the product to normal operation.
E.If the product has been dropped and the base and/or handset has been damaged.
F. If the product exhibits a distinct change in performance.
13.Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric shock from lightning.
14.Do not use the telephone to report a gas leak in the vicinity of the leak.
15.Only put the handset of your telephone next to your ear when it is in normal talk.
SAVE THESE INSTRUCTIONS
FCC, ACTA and IC regulations
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements
are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
*
*
*
*
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
38
www.vtechphones.com
FCC, ACTA and IC regulations
Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product.
This product has been tested and found to comply with the FCC criteria. The handset may be safely held against the ear of the user. The base unit shall be installed and used such that parts of the user’s
body other than the hands are maintained at a distance of approximately 20 cm (8 inches) or more. If you choose to use a clipping device, please make sure to only use the supplied VTech belt clip.
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this
equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be provided to your local telephone company upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant
telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An RJ11 jack should normally be used for connecting
to a single line and an RJ14 jack for two lines. See Installation Instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called. The REN for this product is
encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For more
information, please contact your local telephone company.
This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected to your telephone line, ensure the connection of this equipment does not disable your
alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its
authorized agents. For repair procedures, follow the instructions outlined under the Limited Warranty.
If this equipment is causing harm to the telephone network, the telephone company may temporarily discontinue your telephone service. The telephone company is required to notify you before
interrupting service. If advance notice is not practical, you will be notified as soon as possible. You will be given the opportunity to correct the problem and the telephone company is required to inform
you of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operation, or procedures that could affect the proper functioning of this product.
The telephone company is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
*
*
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
This equipment complies with regulations RSS210 and CS-03 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device.
The term “IC:” before the certification/registration number only signifies that the Industry Canada technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination
on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five.
www.vtechphones.com
39
Additional information
If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:
The RBRC® Seal
The RBRC ® Seal on the nickel-cadmium battery indicates that VTech Communications, Inc. is voluntarily
participating in an industry program to collect and recycle these batteries at the end of their useful lives,
when taken out of service within the United States and Canada.
The RBRC ® program provides a convenient alternative to placing used nickel-cadmium batteries into the
trash or municipal waste,which may be illegal in your area.
VTech’s participation in RBRC ® makes it easy for you to drop off the spent battery at local retailers participating in the
RBRC ® program or at authorized VTech product service centers. Please call 1-800-8-BATTERY TM for information on Ni-Cd
battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment
to protecting our environment and conserving natural resources.
RBRC ® is a registered trademark of Rechargeable Battery Recycling Corporation.
40
www.vtechphones.com
Technical specifications
Enhanced 2.4GHz Technology - Dual band transmission combines the best of 2.4GHz and 900MHz technologies, providing
enhanced performance over standard cordless telephones.
Frequency Control
Crystal controlled PLL synthesizer
Transmit Frequency
Base: 2410.2-2418.9 MHz
Handset: 912.75-917.10 MHz
Receive Frequency
Base: 912.75-917.10 MHz
Handset: 2410.2-2418.9 MHz
Channels
30
Nominal Effective Range
Maximum power allowed by the FCC and IC. Actual operating range
may vary according to environmental conditions at the time of use.
Size
Handset: 167mm X 57mm X 37mm
Base: 131mm X 130mm X 84mm (including antenna)
Weight
Handset: 130 grams
Power Requirements
Handset: 400mAh Ni-Cd Battery
Base: 9V AC @ 250mA
Memory
Directory: 20 Memory locations including the 9 speed dial locations. Up
to 24 digits, 15 characters per location
Caller ID: 45 Memory locations
Base: 165 grams
41
Additional information
www.vtechphones.com
Index
A
Additional information 29-40
B
F
speed dial 23
FCC, ACTA and IC
regulations 38
Noise filter 7
Base features 10
Basic operation 11-28
Belt clip 28
G
C
Handset features 9
Headset operation 28
Call log 24
Caller ID 24
Choose a location 6
Connection 7
D
Delete a directory entry 21
Delete a speed dial entry 17
Dial a directory number 22
Dial a displayed number 25
Dial a speed dial number 18
Dial mode 12
Directory 19
Displaying screen messages 14,26
DSL 7
E
Edit a directory entry 21
42
N
Getting started 4-10
O
Operating range 13
H
I
If you subscribe to DSL
service 7
Important safety instructions 37
Index 42
Install handset battery 5
Installation 5-8
Internet 7
L
Language 13
Low battery warning 6
M
Maintenance 36
Move a directory entry to
www.vtechphones.com
P
Parts checklist 4
R
Re-assign speed dial
locations 18
Removable handset and base
plates 8
Remove records from
call history 25
Review call log 24
Ringer options 27
S
Set date and time 11
Set handset ringer 11
Speed dial 15
Store a call log record in the
directory 25
Store a directory entry 19
Store a speed dial entry 15
T
Technical specifications 41
Telephone operation 12-14
Temporary tone dialing 12
The RBRC ® Seal 40
Troubleshooting 29
W
Warranty 36
www.vtechphones.com
43
VTECH TELECOMMUNICATIONS LTD.
A member of THE VTECH GROUP OF COMPANIES
Distributed in the U.S.A. by VTech Communications, Inc. Beaverton, Oregon
Distributed in Canada by VTech Telecommunications Canada Ltd., Richmond, B.C.
Copyright ©2006 for VTECH TELECOMMUNICATIONS LTD.
Printed in China.
91-000789-010-000
Mod
User’s Manual
www.vtechphones.com
Models: gz2336