EC9000i Series Scanner
User Guide
July 2014
EC9000i Series Scanner User Guide
Compliance statements
Copyright ©2014 by RDM Corporation.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopy, recording, or otherwise,
without the prior written permission of RDM Corporation.
Trademarks
RDM, ITMS, Simply Deposit, Simply Deposit Mobile, Dynamic Decisioning Portal, EC6000i, EC7000i,
EC7500i, and RDM Connect are trademarks or registered trademarks of RDM Corporation. All other
brands and their products are trademarks or registered trademarks of their respective holders and should
be noted as such.
Disclaimer
RDM Corporation makes no warranty with respect to the adequacy of this documentation, programs, or
hardware that it describes for any particular purpose or with respect to the adequacy to produce a
particular result. In no event shall RDM Corporation be held liable for special, direct, indirect, or
consequential damages, losses, cost, charges, claims, demands, or claim for lost profits, fees, or
expenses of any nature or kind.
RDM Corporation
www.rdmcorp.com
End-User/Customer Agreement
Please read the end-user/customer agreement regarding software license and warranty terms during the
installation of the application.
©2014 RDM Corporation
Page 2
EC9000i Series Scanner User Guide
Compliance statements
Compliance statements
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
Warning: Changes or modifications not expressly approved by RDM could void the user’s authority to
operate the equipment.
All units covered by this manual have no user-serviceable parts inside. In the event repairs are ever
needed to any RDM product, they should be performed by RDM Corporation or an authorized
representative of RDM Corporation. For information please contact RDM Corporation,
619A Kumpf Drive, Waterloo, Ontario, Canada N2V 1K8, at 1-800-567-6227, or RDM’s US service agent
below.
US Service Agent
William Buser
(703) 286-5734
bbuser@rdmcorp.com
©2014 RDM Corporation
Page 3
EC9000i Series Scanner User Guide
Contents
Contents
Compliance statements................................................................................................................................. 3
FCC Compliance Statement ..................................................................................................................... 3
Contents ........................................................................................................................................................ 4
Introduction ................................................................................................................................................... 6
About this guide ........................................................................................................................................ 6
Requirements ............................................................................................................................................ 6
Recommendations .................................................................................................................................... 6
RDM EC9000i models and features ............................................................................................................. 7
Serial and model number .......................................................................................................................... 8
Programmable application button ............................................................................................................. 8
Setting up your scanner ................................................................................................................................ 9
Choose a location ..................................................................................................................................... 9
Unpack the shipping box ........................................................................................................................... 9
Inspect the scanner’s features ................................................................................................................ 10
EC9000i Series scanner (most models) ............................................................................................. 10
EC9000i Series scanner with printer ................................................................................................... 11
Internal components................................................................................................................................ 12
Inside the front cover - side view ........................................................................................................ 12
Inside the front cover - back view ....................................................................................................... 13
Inside the front cover and endorsement printer cover - top view ........................................................ 14
Connection ports ................................................................................................................................. 15
Removing the covers .............................................................................................................................. 15
Front cover .......................................................................................................................................... 15
Endorsement printer cover .................................................................................................................. 16
Franker and endorser inkjet cartridges .................................................................................................. 16
Installing the franker cartridge ............................................................................................................. 17
Replacing the endorser inkjet cartridge .............................................................................................. 17
Replacing the paper roll for the printer.................................................................................................... 18
Connecting the power cord ..................................................................................................................... 19
Disconnecting the power cord ............................................................................................................. 19
©2014 RDM Corporation
Page 4
EC9000i Series Scanner User Guide
Contents
Drivers and Applications ......................................................................................................................... 19
Operating the scanner................................................................................................................................. 20
Preparing documents .............................................................................................................................. 20
Feeding documents................................................................................................................................. 20
Single-feed mode ................................................................................................................................ 20
Auto-feed mode ................................................................................................................................... 20
Swiping magnetic stripe cards (optional) ................................................................................................ 21
Imaging identification cards..................................................................................................................... 21
Light signals and beeps .......................................................................................................................... 22
During start up ..................................................................................................................................... 22
During document scanning and processing ........................................................................................ 22
A typical document processing / LED cycle ........................................................................................ 22
Maintaining your scanner ............................................................................................................................ 23
Cleaning the scanner .............................................................................................................................. 23
Cleaning the outside cabinetry ............................................................................................................ 23
Cleaning the inside of the scanner unit ............................................................................................... 23
Cleaning the image sensor ..................................................................................................................... 23
Troubleshooting .......................................................................................................................................... 24
Scanner does not respond ...................................................................................................................... 24
Card transactions do not function properly ............................................................................................. 24
Printer does not print ............................................................................................................................... 24
Specifications .............................................................................................................................................. 25
Part Numbers .......................................................................................................................................... 27
Scanners ............................................................................................................................................. 27
Additional parts ................................................................................................................................... 28
Warranty Information................................................................................................................................... 29
LIMITED WARRANTY: ........................................................................................................................... 29
WARRANTY SPECIFICS:....................................................................................................................... 29
©2014 RDM Corporation
Page 5
EC9000i Series Scanner User Guide
Introduction
Introduction
The RDM EC9000i series scanners provide affordable functionality in a compact, efficient design.
Featuring RDM’s industry leading Progressive MICR Method and imaging technology, the EC9000i series
scanners deliver optimum MICR read rates and image quality. In addition, all EC9000i scanners include a
franker printer and cartridge to comply with various payment industry guidelines.
With several models and feature options to choose from, the RDM EC9000i series scanners are an ideal
fit for payment applications such as remote deposit capture, check cashing, teller capture, healthcare
POS, retail POS, and walk-in bill payments.
About this guide
This guide describes the EC9000i series scanners, some basic operations, and how to maintain your
scanner. For instructions on how to use your scanner to scan documents with your computer, contact
your solution provider.
Requirements
The RDM EC9000i unit is for indoor use only. Keep the RDM EC9000i dry; avoid areas of high humidity.
Do not remove any parts from areas that are not described in this guide. Removing parts from areas not
described in this guide will void the warranty.
When you are working inside the scanner, such as when you are replacing the franker cartridge, make
sure the scanner’s power is disconnected.
Recommendations
Record all distributor contact information for future reference.
Save the original box and packing material. Reuse them if the unit must be shipped to a new location or
returned for service.
Position the unit so that the operator has easy access to the document path and a clear view of the LED.
Do not put the unit close to a heat source, in direct sunlight, or close to any device that can emit
electromagnetic interference, such as a computer monitor or power adapter.
©2014 RDM Corporation
Page 6
EC9000i Series Scanner User Guide
RDM EC9000i models and features
RDM EC9000i models and features
The RDM EC9000i series scanner is available in several optional model configurations. All models
include an integrated ID card imager and a franker.
All scanner models can also be licensed to perform optical character recognition (OCR) on documents
with machine printed text (remittances, pay stubs). This can be used with different applications such as
walk-in bill payment. You can tell if your scanner is licensed for OCR by the label on the bottom of the
scanner.
The following table lists the available EC9000i models. A complete list of models, options and part
numbers can be found in the Part Numbers section at the back of this guide.
Model
Description
EC9001f
Auto-feed scanner.
EC9002f
Auto-feed scanner with MSR.
EC9003f
Auto-feed scanner with endorser.
EC9004f
Auto-feed scanner with MSR and endorser.
EC9103f
Single-feed or auto-feed scanner with endorser.
EC9104f
Single-feed or auto-feed scanner with endorser and MSR.
EC9107f
Single-feed or auto-feed scanner with endorser and receipt printer.
EC9108f
Single-feed or auto-feed scanner with endorser, MSR, and receipt printer.
EC9111f
Single-feed scanner.
EC9112f
Single-feed scanner with MSR.
©2014 RDM Corporation
Page 7
EC9000i Series Scanner User Guide
RDM EC9000i models and features
Serial and model number
You can locate your scanner’s model and serial number on the bottom of the unit.
Programmable application button
This button is located on the front right of the scanner. The light indicates the status of the scanner. For
more information, see Light signals and beeps.
Third-party applications can configure the application button to perform a
variety of functions. These functions might include opening a document,
launching a website, or starting an application. Not all applications use the
application button.
Developers can find information about programming the application button
in the help file that is included with RDM’s application development kit
(ADK). Developers can obtain the ADK by contacting RDM.
Note: The programmable application button is not supported on some scanner models. The LED is
supported on all models.
©2014 RDM Corporation
Page 8
EC9000i Series Scanner User Guide
Setting up your scanner
Setting up your scanner
To set up the RDM EC9000i scanner:
•
Choose a location.
•
Unpack the shipping box.
•
Inspect the scanner’s features.
•
Insert the franker cartridge.
•
Insert the endorser inkjet printer cartridges, if one is included with your scanner.
•
Insert the receipt paper roll, if one is included with your scanner.
Choose a location
Locate your scanner in a place that:
•
Has a flat surface, such as a counter top or table.
•
Is convenient for the scanner operator.
•
Offers adequate ventilation and protection from elements such as heat, dust, oil, or moisture.
•
Is close to the application PC (USB 2.0 high speed connection required).
•
Is close to an electrical outlet.
Unpack the shipping box
1. Open the top of the box.
2. Remove and unwrap the items. Lift the scanner out of the box from the bottom of the scanner.
3. Save the box and packing material for future use.
The shipping box includes the following items:
•
•
•
•
•
•
•
RDM EC9000i scanner
USB cable
Power adapter
Franker cartridge
Endorser inkjet cartridges (certain models)
5-pack inkjet blotter (certain models)
3” thermal receipt paper roll (certain models)
©2014 RDM Corporation
Page 9
EC9000i Series Scanner User Guide
Setting up your scanner
Inspect the scanner’s features
EC9000i Series scanner (most models)
Endorsement printer cover
Exit pocket
Insertion
hopper
Exit extension
Front cover
Programmable
Programmable
application
button
and
application
button
and
scanner
status
LED
scanner
status
LED
Insertion extension
©2014 RDM Corporation
Page 10
EC9000i Series Scanner User Guide
Setting up your scanner
EC9000i Series scanner with printer
Endorsement printer cover
Exit pocket
Front cover
Exit pocket tab
Programmable
application button and
scanner status LED
Insertion
hopper
Printer paper feeder
Printer cover release button
Printer cover
©2014 RDM Corporation
Page 11
EC9000i Series Scanner User Guide
Setting up your scanner
Internal components
Inside the front cover - side view
Image sensor
(closed)
Insertion hopper
ID card entry slot
Document feeder
©2014 RDM Corporation
Page 12
EC9000i Series Scanner User Guide
Setting up your scanner
Inside the front cover - back view
Some scanners do not include all of the pictured connection ports or buttons.
Franker
ID card entry
imaging slot
Franker
cartridge latch
Metal Plate
(aligns with slot in
franker cartridge)
©2014 RDM Corporation
Page 13
EC9000i Series Scanner User Guide
Setting up your scanner
Inside the front cover and endorsement printer cover - top view
Back
Metal post for top cover
Franker
ID card entry imaging
slot
Document track
Image sensor
and panels
(closed)
Endorsement printer
(select models)
Magnetic
stripe reader
(MSR)
Metal post for
top cover
Scanner LED
Exit pocket
Insertion hopper
Front (extensions retracted)
©2014 RDM Corporation
Page 14
EC9000i Series Scanner User Guide
Setting up your scanner
Connection ports
K-slot
USB hub
ports
USB
Power
On/off
switch
Note: Not all scanner models include every item shown in the diagram.
Connector
Description
USB Hub Ports
Use this port to connect optional peripheral devices such as a PIN entry
device, or to recharge a mobile device such as a phone.
USB
High-speed 2.0 (480 Mb/s). Use this port to connect to a computer.
Power
Connect the power adaptor to this port. You must use the RDM A to B, USB
cable.
On/Off Switch
Powers the scanner on or off independent of the computer.
K-Slot
The K-Slot or Kensington® Security Lock lets you secure the unit with a
cable (not provided) that locks into the slot. Cables can be purchased from
your local computer supply store.
Removing the covers
RDM EC9000i scanner has two covers that can be removed in order to clean the image sensor, replace
cartridges, or clear paper jams.
Front cover
Remove the front cover when you need to clear paper jams,
replace the franker cartridge, or to clean the image sensor.
1.
2.
3.
4.
Disconnect the power cord from the scanner.
Pull the insertion extensions forward.
Grasp the front and the back end of the front cover.
Gently pull the cover upwards until it detaches from
the scanner.
©2014 RDM Corporation
Page 15
EC9000i Series Scanner User Guide
Setting up your scanner
To replace the front cover:
Caution: Before you replace the front cover, make sure the insertion extensions are pulled forward.
Otherwise, you might damage the front cover.
1. Carefully place the front cover over the scanner assembly. Make sure that the cover overlaps the
assembly correctly by lining it up with the metal posts.
2. Gently push the cover down until it snaps into place.
Endorsement printer cover
Remove the endorsement printer cover when you need to clear paper jams, to insert or replace the
endorser inkjet printer cartridge, or to clean the image sensor.
1. Grasp the top of the endorsement printer cover.
2. Gently pull the cover upwards until it detaches from the scanner.
To replace the endorsement printer cover:
1. Carefully place the endorsement printer cover over the scanner assembly; make sure that the
cover overlaps the assembly correctly.
2. Gently push the cover down until it snaps into place.
Franker and endorser inkjet cartridges
The franker cartridge creates a red ink stamp that defaces the front of each check
with a message that says “Electronically Presented”. All EC9000i scanners come
with a franker cartridge.
Certain EC9000i scanners are capable of endorsing checks but the cartridges are
not included with scanners. With your scanning application, the endorser inkjet
printer places user-defined text on the rear of the check.
Franker or inkjet cartridges can be purchased by contacting your solution
provider or reseller.
Follow the directions below to insert the cartridges into the scanner unit.
Franker cartridge
Inkjet cartridge
Caution:
•
•
•
•
•
•
Ink might be harmful if swallowed.
Avoid contact with eyes.
Damage to the unit or the cartridge which results from modifying the inkjet
cartridge is not the responsibility of RDM.
The inkjet cartridge is not refillable.
Inkjet cartridges are not licensed for modifications.
RDM may change product designs, features, or specifications at any time.
©2014 RDM Corporation
Page 16
EC9000i Series Scanner User Guide
Setting up your scanner
Installing the franker cartridge
1. Disconnect the power cord from the scanner.
2. Remove the front of the scanner.
At the back of the scanner, the franker
cartridge is held in place by a blue franker
latch and a metal plate.
3. Lift the blue franker latch.
4. Pull the franker cartridge out of the scanner by
the franker tab.
5. Insert the new franker cartridge. Make sure
the metal plate fits into the franker cartridge
like in the picture above.
6. Push the franker cartridge into the scanner by
pushing in the metal plate and then lowering
the blue latch over the franker cartridge until it
snaps closed.
7. Replace the scanner cover.
Franker tab
Franker latch
Metal plate
Replacing the endorser inkjet cartridge
When you place the new inkjet cartridge into the holder, make sure that you insert it at the angle
described in the following steps. If you do not insert the cartridge properly, it might not make contact with
the document when it is scanned.
1. Disconnect the power cord from the scanner.
2. Remove the endorsement printer cover.
3. Pull the inkjet latch away from the printer cartridge.
4. Pull the inkjet cartridge out of the scanner.
©2014 RDM Corporation
Page 17
EC9000i Series Scanner User Guide
Setting up your scanner
5. To insert the new inkjet cartridge, pull the inkjet latch back and place the inkjet cartridge into the
holder. The cartridge needs to be at an angle so that the back of the cartridge is lower than the
front of the cartridge.
6. Push the cartridge down into the holder until the cartridge snaps into place.
Once installed, the inkjet cartridge sits on a slight angle with the back of the cartridge lower than
the front.
7. Make sure there is no gap between the inkjet cartridge and the endorsement channel.
8. Replace the endorsement printer cover.
Replacing the paper roll for the printer
If your scanner has a printer, the following steps
describe how to replace the paper roll.
1. Press the printer cover release button and
completely open the printer cover.
2. Remove the empty paper roll from the paper
compartment.
3. Insert the new paper roll into the compartment,
with the end of the paper roll rolling from the top.
4. Pull the paper out of the compartment and close
the printer cover with the paper sticking out.
Push the cover closed in the center of the printer
cover.
Make sure the cover is completely closed. If you
push the cover from the sides, the cover might
not close completely. When closed correctly,
both sides of the printer cover are flush with the scanner.
5. Rip off any access paper sticking out of the printer cover.
©2014 RDM Corporation
Page 18
EC9000i Series Scanner User Guide
Setting up your scanner
Connecting the power cord
1. Align the flat side of the power connector so that it is facing up.
2. Insert the round end of the power cord into the power port on the back of the scanner.
When the cord is pushed in completely, it clicks into place.
3. With the power cord connected to the power adapter, plug the other end of cord into a power
outlet.
Disconnecting the power cord
Caution: Disconnecting the scanner from a power source while the scanner is processing a transaction
might cause data loss.
The power cord has a sleeve on it that secures it to the unit. The security sleeve prevents the power cord
from being pulled out of the unit accidently.
1. Hold the unit in place with one hand to prevent the unit from falling.
2. With your other hand, slide the power cord security sleeve back and pull the power cord free of
the scanner.
Drivers and Applications
The drivers for your scanner are installed on your computer when you install the check scanning
application. There are many applications that support the RDM EC9000i scanner. Most are available from
third-party vendors.
If you are not sure where to acquire your check scanning application, check with whoever provided your
scanner.
©2014 RDM Corporation
Page 19
EC9000i Series Scanner User Guide
Operating the scanner
Operating the scanner
Caution: Do not open the cover or try to access the inside of the scanner while it scans a document.
Preparing documents
To reduce the possibility of errors and damage to the unit:
•
•
•
•
Remove all folds and creases in the document.
Remove any paper clips and staples from the document.
Make sure that documents are not stuck together.
Make sure that documents are dry.
Feeding documents
The scanner unit is ready to accept documents when the LED is flashing green. Insert the documents
either one at a time (single-feed mode), or in a batch (auto-feed mode).
Make sure that you place the documents into the feeder with the MICR line at the bottom and facing
towards the outside of the scanner.
Caution:
•
If you are scanning documents that are larger than a personal check, make sure that the
extensions are pulled out. Documents can be damaged if the extensions are not pulled out.
•
If your scanner includes a printer, make sure that you adjust the exit pocket tab to fit the
documents you are scanning. If the tab does not fit the documents, the scanner could jam.
Single-feed mode
1. Start the scanning process. For example, click Scan on your PC application.
2. Place one document into the insertion hopper until the scanner pulls the document into the
scanner.
The document is scanned and processed.
3. Repeat steps 1 and 2 until you have scanned all of your documents.
Auto-feed mode
1. Place up to 30 documents into the insertion hopper.
Note: Do not push documents past the check icon on the right side
of the insertion hopper.
2. If you are required to do so, start the scanning process. For
example, click Scan on your PC application.
©2014 RDM Corporation
Page 20
EC9000i Series Scanner User Guide
Operating the scanner
Swiping magnetic stripe cards (optional)
1. Place the card in the slot on the side of the scanner with the stripe down and facing in towards
the body of the scanner.
2. Swipe the card either from back to front or front to back.
Imaging identification cards
The ID imager uses the same track as the document scanner, but you insert cards at the back of the
scanner. Insert the card into the scanner so that the front of the ID card faces away from the scanner. The
ID imager scans both the front and back of the identification card.
1. Insert the identification card into the back of the scanner track until you feel it pinch the card.
The scanner pulls the card through the track.
2. Remove the card from the front of the scanner track.
©2014 RDM Corporation
Page 21
EC9000i Series Scanner User Guide
Operating the scanner
Light signals and beeps
The scanner’s status is shown through a single, multistate LED (light-emitting diode), which is the light on
the top, front, right-hand side of the unit. The table below describes typical status signals and their
meanings.
During start up
Signals
Meaning / What to do
Red-red-green-green flashing
cycle
Red-green flashing cycle
The scanner is being configured by the application. Wait for the
application to finish configuring the scanner.
Red-amber-green
The scanner is connecting to the application. Wait for the scanner to
connect.
Green solid
The scanner is configured but idle. The scanner is ready.
During document scanning and processing
Signals
Meaning / What to do
Green flashing
The scanner is waiting for the user to insert a document into the
feeder.
Green flashing with one short
beep
The scanner read the document successfully.
Green-red flashing cycle
The scanner is processing the document. Wait for the scanner to
finish.
Red flashing and one short
beep
An error occurred while the scanner was processing the document.
Check your PC application for instructions or refer to your local
procedures. If you need more help, contact your distributor (reseller).
Red flashing and one long beep
An error occurred while the scanner was processing the document or
storing the captured image. Check your PC application for instructions
or refer to your local procedures. If you need more help, contact your
distributor (reseller).
Red flashing and three short
beeps
The scanner was not able to read the MICR line.
A typical document processing / LED cycle
1.
2.
3.
4.
The LED is Green (Solid): The unit is idle.
The LED is Green (Flashing): The scanner is waiting for a document to be inserted for scanning.
The LED is Green/Red (Flashing): The scanning operation is in progress.
The LED is Green (Solid): The scanning operation is complete. The scanner has returned to its
idle state.
©2014 RDM Corporation
Page 22
EC9000i Series Scanner User Guide
Maintaining your scanner
Maintaining your scanner
The EC9000i series scanners perform best when all working surfaces are clean and free of foreign
material.
Cleaning the scanner
Caution:
• Always disconnect the scanner from its power source before cleaning it.
• Solvents or harsh cleaners might damage or discolor the cabinetry.
Cleaning the outside cabinetry
Use a damp cloth and mild soap.
Cleaning the inside of the scanner unit
1. Remove the front cover and the endorsement printer cover.
2. Use a dusting brush designed for use with electronic equipment or a compressed air duster to
clean inside the scanner.
3. Replace the covers.
Cleaning the image sensor
Caution: Always disconnect the unit from its power source before
cleaning the image sensor.
1. Remove the front cover and the endorsement printer cover.
2. Open both the front and back panels that cover the image
sensor.
The front panel can open up to 90°. The back panel opens
only a few degrees.
3. Use any of the following to gently remove any ink or dust
from the image sensor.
• A lens cleaning tissue.
• A damp lint-free cloth.
• A cotton swab dampened with rubbing alcohol.
4. Clean the glass on each panel thoroughly.
5. Replace each of the covers.
©2014 RDM Corporation
Page 23
EC9000i Series Scanner User Guide
Troubleshooting
Troubleshooting
In the course of everyday operations, you might encounter minor malfunctions in the RDM EC9000i
scanner. Before calling for service, review the troubleshooting steps below.
Scanner does not respond
1. Ensure the cable that connects your scanner to your computer is properly connected to the
correct port on the back of the scanner and computer (according to instructions provided by your
distributor).
2. Make sure that the correct power cord is connected to the unit. Change or replace the cord, if
necessary.
3. If the problem persists, contact your solution provider or help desk.
Card transactions do not function properly
1. Ensure that you are swiping the card properly.
The black magnetic stripe on the back of the card must face downward and towards the body of
the scanner.
2. Try using another card to ensure the first card was not defective.
3. If the problem persists, contact your solution provider or help desk.
Printer does not print
1. Ensure that the printer has not jammed.
2. Ensure that the end of the paper roll rolls from the top of the roll.
3. If the problem persists, contact your solution provider or help desk.
©2014 RDM Corporation
Page 24
EC9000i Series Scanner User Guide
Specifications
Specifications
Model details
Physical dimensions
Depth:
•
•
Width:
•
•
Height:
•
•
Retracted Extensions: 237mm [9.3”]
Fixed Extensions(Printer): 311mm [12.25”]
Non-MSR Units: 154mm [6.0”]
MSR Units: 157mm [6.2”]
Non-Printer Units: 175mm [6.9”]
Printer Units: 245mm [9.65”]
Document feed capacities
Document size
Height:
• Minimum: 50.8mm [2“]
• Maximum: 101.6mm [4”]
Length:
• Minimum: 101.6mm [4”]
• Maximum: 228.60mm [9”]
Preferred Paper Weight: 20 to 32 lb
Single feeder capacity
(EC9111f/9112f only)
Single document.
Auto feeder capacity
(most models)
Auto feeder with double-feed detect.
Supports single feed or batches up to 30 items.
[Depends on document thickness and condition].
Document collection pocket
Up to 60 documents.
[Depends on document thickness and condition].
Maintains the integrity of the order of the original source documents.
Technical features
MICR reader
©2014 RDM Corporation
E13B or CMC7 MICR Fonts.
Uses RDM’s Progressive MICR Method for optimum MICR read
accuracy.
OCR E13B MICR Assist.
Page 25
EC9000i Series Scanner User Guide
Specifications
Image capture
Duplex Document Imaging.
Tiff 6.0 file format.
100 or 200 DPI.
Grayscale with JPEG (or no) compression.
Bi-level with CCITT Group 4 (ITU T.6) (or no) compression.
Tiff 6.0 images contain MICR line and transaction information in header
description tags of check images and optionally OCR line and transaction
information in header description tags of bill stubs.
Image size varies according to document characteristics, file format, DPI
and compression, typically 10 kB or less for Tiff 6.0 bi-level with CCITT
Group 4 compression.
Image Quality Assurance
(IQA)
IQA includes: too light/too dark /skew (Bi-Level Images Only).
Magnetic Stripe Reader
(MSR) (optional)
3-track, bi-directional, alphanumeric.
Identification (ID) card
imager
Duplex Imager.
54mm [2.13”] (V) x 86mm [3.39”] (H) with 200(V)/400(H) DPI resolution.
OCR Font Recognition
(optional license)
Under application control Alphanumeric OCR A and B font recognition of
OCR code-lines for applications such as bill payment.
Franker
Under application control a fixed text message “Electronically Presented”
can be stamped on the front of a document, in red ink.
Endorsement printer
Under application control, a single line 1/8” high text message can be
printed on the rear of a document.
Programmable
application button
(except EC9111f/91112f)
Under third-party application control, button can be programmed to
perform various application functions.
Scanner status LED
Integrated with application button - provides the unit’s status via
illuminated LED.
Communication ports
High Speed USB 2.0 (480 MBits/sec) on all models.
Built-in 2 port hub (except EC9111f and EC9112f).
Receipt Printer
(select models)
Front-mounted, 3” thermal receipt printer.
Clamshell paper load.
Paper width 80mm (3.15”).
Print width 71mm (2.8”).
Maximum print speed of 170mm/sec (6.7”/sec).
Windows emulation.
Uses power from scanner’s power supply.
Connects to PC using the scanners USB cable connection.
©2014 RDM Corporation
Page 26
EC9000i Series Scanner User Guide
Specifications
Software and support
Supported operating
systems
Windows XP, Windows 7 (32/64-bit), Windows 8 (32/64-bit), Windows 8.1
(32/64-bit).
Development software
RDM EC Scanner Application Development Kit (ADK) includes API
components, USB driver, Redistributable Installation Packages and
Sample Applications.
Environment
Operating temperature
10 to 40 Degrees C (50 to 104 Degrees F).
Operating humidity
10 to 85% relative humidity (non-condensing).
Power Rating
Unit input
(24VDC)
Non Printer Models: 900mA.
Printer Models: 2.5A.
Power supply input range
100–240V, 50/60 Hz.
Certifications
Industry certifications including.
WHQL driver certification (USB Drivers).
CSA (Safety)
• For use with model no GFP241DA-2410M-2 or 3A-242DA24.
• Pour utiliser avec modèle GFP241DA-2410M-2 or 3A-242DA24.
FCC (EMI)
Warranty
2 year standard warranty.
Life expectancy
5 years under normal usage.
Part Numbers
Scanners
Model
RDM Part Number
EC9001f auto-feed (25 DPM)
6000-9001-FRK
EC9001f auto-feed (25 DPM), OCR licensed
6000-9001-OFR
EC9002f auto-feed (25 DPM), MSR
6000-9002-FRK
EC9002f auto-feed (25 DPM), MSR, OCR licensed
6000-9002-OFR
EC9003f auto-feed (25 DPM), endorser
6000-9003-FRK
EC9003f auto-feed (25 DPM), endorser, OCR licensed
6000-9003-OFR
EC9004f auto-feed (25 DPM), MSR, endorser
6000-9004-FRK
EC9004f auto-feed (25 DPM), MSR, endorser, OCR licensed
6000-9004-OFR
©2014 RDM Corporation
Page 27
EC9000i Series Scanner User Guide
Specifications
EC9103f single-feed, endorser
6000-9103-S000
EC9103f single-feed, endorser, OCR licensed
6000-9103-S00R
EC9104f single-feed, MSR, endorser
6000-9104-S000
EC9104f single-feed, MSR, endorser, OCR licensed
6000-9104-S00R
EC9107f single-feed, endorser, receipt printer
6000-9107-S000
EC9107f single-feed, endorser, receipt printer, OCR licensed
6000-9107-S00R
EC9108f single-feed, MSR, endorser, receipt printer
6000-9108-S000
EC9108f single-feed, MSR, endorser, receipt printer, OCR licensed
6000-9108-S00R
EC9103f auto-feed (90 DPM), endorser
6000-9103-9000
EC9103f auto-feed (90 DPM),endorser, OCR licensed
6000-9103-900R
EC9104f auto-feed (90 DPM), MSR, endorser
6000-9104-9000
EC9104f auto-feed (90 DPM), MSR, endorser, OCR licensed
6000-9104-900R
EC9107f auto-feed (90 DPM), endorser, receipt printer
6000-9107-9000
EC9107f auto-feed (90 DPM), endorser, receipt printer, OCR licensed
6000-9107-900R
EC9108f auto-feed (90 DPM), MSR, endorser, receipt printer
6000-9108-9000
EC9108f auto-feed (90 DPM), MSR, endorser, receipt printer, OCR licensed
6000-9108-900R
EC9111f single-feed
6000-9111-0000
EC9111f single-feed with OCR
6000-9111-000R
EC9112f single-feed, MSR
6000-9112-0000
EC9112f single-feed, MSR,OCR licensed
6000-9112-000R
Additional parts
Options and accessories
RDM Part number
Replacement franker cartridge – “Electronically Presented” red ink
6000-6065
Replacement HP inkjet printer cartridge black ink (for endorser)
6000-6060 (HP C6602A)
EC9000i Ink Jet Blotter (14mm x 11mm x 2mm) - 5 Pack
302987
Paper Roll, Thermal, 3.125" W x 225' (3.125” maximum diameter)
Standard thermal roll paper
available from office supply stores
Replacement Power Adapter
Non-Printer Models: 302843
Printer Models: 303811
USB 2.0 cable, A to B male, shielded, 2m (Black)
6000-6106
©2014 RDM Corporation
Page 28
EC9000i Series Scanner User Guide
Warranty Information
Warranty Information
LIMITED WARRANTY:
RDM EC9000i™ is warranted against defects in materials and workmanship under normal use and
service for a period of two years after the date of receipt by you. This warranty is extended only to the
original purchaser. Extended warranty programs might be offered by your solution provider.
The entire liability of RDM Corporation (the Corporation), distributors of the RDM EC9000i scanner and
manufacturers of auxiliary equipment used with the RDM EC9000i and your exclusive remedy shall be, at
the Corporation’s option either (a) return of the price paid, or (b) repair or replacement of the RDM
EC9000i scanner that does not meet the limited warranty and which is returned to the Corporation with a
purchase receipt or other proof of date of original purchase which will be required in order to exercise
your rights under this warranty.
The limited warranty is void if failure of the RDM EC9000i has resulted from accident, abuse or
misapplication. Any replacement RDM EC9000i will be warranted for the remainder of the original
warranty period.
The equipment is sold with the understanding that neither the Corporation, such distributors nor such
manufacturers will be liable for any damages whatsoever (include, without limitation, direct or indirect
damages for personal injury, loss of business profits, business interruption, loss of business information,
or any other pecuniary loss) arising out of the use of or inability to use the RDM EC9000i, even if the
Corporation, such distributors and/or such manufacturers have been advised of the possibility of such
damages.
In any case, the entire liability of the Corporation, such distributors and such manufacturers with respect
to the RDM EC9000i shall be limited to the amount actually paid by you for the RDM EC9000i. The
Corporation, such distributors and such manufacturers disclaim all other warranties, express or implied,
including, without limitation, implied warranties of merchantability and fitness for a particular purpose with
regard to the RDM EC9000i and the accompanying written materials.
WARRANTY SPECIFICS:
This warranty only covers failures due to defects in materials or workmanship, which occur during normal
use.
It does not cover the following:
•
•
•
•
Damage, which occurs in shipment;
Failures which are caused by products not supplied by RDM;
Failures which result from accident, misuse, abuse, neglect, excessive dirt or dust cause by lack
or preventative maintenance measures, mishandling, misapplication, alteration or modification;
Service by anyone other than RDM;
©2014 RDM Corporation
Page 29
EC9000i Series Scanner User Guide
•
Warranty Information
Damage that is attributable to acts of nature including but not limited to:
o Flood, lightning, power surge or static electricity, water damage, fall, theft, or vandalism;
o Spillage of liquid or objects that have fallen into the equipment;
o Equipment that has been exposed to excessive heat or unstable environmental
conditions;
o Consumables such as Franker Roller or Franker Assembly, or other RDM EC9000i
consumables or accessories such as cables.
RDM scanner units with problems found to be caused by incorrectly set configuration parameters (IRN#,
Owner Code, Merchant ID, etc.) are not considered defective and will not be serviced under warranty.
Warranty is void if any of the external case of the unit has been opened or removed or the unit has, in
RDM’s opinion, been damaged through misuse or improper care.
Units returned to RDM for warranty repair will be reconfigured with factory defaults and returned to
customers.
©2014 RDM Corporation
Page 30