Emerson Liebert XDR Specifications

Precision Cooling
For Business-Critical Continuity™
Liebert® Xtreme Density™
System Design Manual
TABLE OF CONTENTS
1.0
SYSTEM DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
European Union Fluorinated Greenhouse Gas Requirements . . . . . . . . . . . . . . . . . . . . . . . .
Generic Piping Layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDA—Air Flow Enhancer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDCF—Liebert XD CoolFrame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDH—Horizontal Cooling Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDO—Overhead Cooling Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDR—Rear Cooling Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDV—Vertical, Above-Cabinet Cooling Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDC—Refrigerant Chiller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.10
Liebert XDP—Pumping Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.9.1
1
2
3
4
5
6
7
8
9
Liebert XDC Minimum Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.10.1 Liebert XDP Minimum Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.11
Liebert XD Piping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.11.1 Liebert XD Field Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.0
STARTING A NEW EQUIPMENT COOLING PROJECT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.1
2.2
Determining Cooling Equipment Needs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Implementing a Hot-Aisle/Cold Aisle Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.0
DESIGNING A LIEBERT XD SOLUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1
3.2
3.3
3.4
Determine Cooling Requirements and Select Liebert XD System . . . . . . . . . . . . . . . . . . . .
Calculate the Heat Load to be Handled by Liebert XD System . . . . . . . . . . . . . . . . . . . . . .
Selecting Liebert XD Cooling Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring a Liebert XD System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.1
3.4.2
3.5
3.6
3.7
3.8
3.9
17
18
19
20
Determining Spacing of Liebert XDOs in an Aisle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Determining Vertical Placement of Liebert XDOs Above the Cold Aisle . . . . . . . . . . . . . . . . 21
Liebert XDR Module Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.9.1
3.10
3.11
3.12
3.13
3.14
3.15
3.16
3.17
3.18
Number of Modules Supported by a Liebert XDP or Liebert XDC . . . . . . . . . . . . . . . . . . . . . 16
System Connection Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Airflow Requirements for Liebert XD Solutions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDCF Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDH Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDO Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.8.1
3.8.2
13
13
15
16
Airflow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Liebert XDV Module Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDP/Liebert XDC Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Examples of Expansion and Interlaced Connection of Liebert XD Cooling Modules . . . . . .
Liebert XD Piping System Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XD Piping Slope. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bypass Flow Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Piping Details—Shutoff/Isolation Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Piping Details—Shutoff/Isolation Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Piping Details—Return Header Port Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
i
23
24
24
27
29
29
31
31
33
3.19
3.20
3.21
3.22
3.23
Piping Details—Bull Heading Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Piping Installation Method Prefabricated Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XD Flex Pipe Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XD Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Determining Refrigerant Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
35
39
39
40
3.23.1 Liebert XDP/Liebert XDC Pumped R-134a Circuit Volume . . . . . . . . . . . . . . . . . . . . . . . . . . 40
3.23.2 Calculating Refrigerant R134a Charge—Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
3.24
3.25
3.26
3.27
Chilled Water Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temperature/Humidity Sensor Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Liebert XDP and Liebert XD Cooling Modules in a CANbus Network . . . . . . .
42
44
44
45
3.27.1 CANbus Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.27.2 CANbus Cable Length in a Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.27.3 Remote Sensor Placement Within the CANbus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
4.0
LIEBERT XD COOLING MODULES—LIEBERT XDCF, LIEBERT XDH, LIEBERT XDO,
LIEBERT XDR AND LIEBERT XDV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4.1
4.2
4.3
4.4
Liebert XDCF Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDCF Mechanical Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDCF Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDCF Piping Connection Methods and Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.1
49
50
51
51
Header System—Liebert XDCF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.12
4.13
4.14
4.15
4.16
4.17
4.18
Liebert XDH Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Features—Liebert XDH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting High-Voltage Wiring—Liebert XDH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Low-Voltage Wiring—Liebert XDH Smart Modules . . . . . . . . . . . . . . . . . . . . .
Liebert XDO Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Features Liebert XDO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low-Voltage Wiring—Liebert XDO Smart Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDR Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Features—Liebert XDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDR Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDV Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Features—Liebert XDV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High-Voltage Cabling for Liebert XDV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low-Voltage Wiring—Liebert XDV Smart Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.0
LIEBERT XDC AND LIEBERT XDP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
5.1
Liebert XDC Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
5.2
Liebert XDP Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
6.0
HEAT REJECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
6.1
Liebert Lee-Temp™ Refrigerant Control Air-cooled Condensers. . . . . . . . . . . . . . . . . . . . . . 95
5.1.1
6.1.1
6.1.2
52
53
55
56
57
57
63
64
64
65
69
69
74
78
Liebert XDC Optional Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Liebert Lee-Temp Refrigerant Control Air-Cooled Condenser . . . . . . . . . . . . . . . . . . . . . . . . 95
Standard Features-All Condensers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
ii
6.1.3
6.1.4
6.1.5
6.1.6
6.1.7
Condenser Coil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Propeller Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fan Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
95
95
96
96
96
6.2
Mechanical Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
6.3
Heat Rejection Piping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
6.2.1
6.3.1
6.4
Liebert XDC DX R-407c Circuit Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Liebert Drycoolers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
6.6.1
6.6.2
6.7
6.8
6.9
6.10
6.11
Air-Cooled Condenser with Liebert Lee-Temp “Flooded Condenser” Head Pressure
Control System—R-407C (DX) Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Calculating Refrigerant Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
6.5.1
6.6
Piping for Direct Expansion (DX) Circuit—R-407C Air-Cooled Units . . . . . . . . . . . . . . . . . . 99
Install Double Discharge Risers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
6.4.1
6.5
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Liebert Drycooler Fan Cycling Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Pump Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Typical System configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Site Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions and Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting the Drycooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glycol Piping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
110
112
112
115
115
6.11.1 Piping Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
6.11.2 Expansion Tanks, Fluid Relief Valves, Air Management and Other Devices . . . . . . . . . . . 116
6.12
Electrical Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
6.12.1 Line Voltage Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
6.12.2 Low Voltage Control Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
6.13
Filling Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
6.13.1 Preparing the System for Filling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
6.13.2 Glycol Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
6.13.3 Filling the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
6.14
Outdoor Control Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
6.14.1
6.14.2
6.14.3
6.14.4
6.14.5
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hazardous Voltage Power Supply Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Extra-Low Voltage Control Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dual Pump Package Flow Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dual Pump Controls Sequence of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
123
123
124
124
124
7.0
LIEBERT ICOM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
7.1
7.2
7.3
Liebert iCOM Display Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Cooling Module Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Graphical Data Record. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
7.3.1
7.3.2
7.4
7.5
7.6
Liebert iCOM User Menu Icons and Legend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Liebert iCOM Service Menu Icons and Legend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Liebert XDC Alarms Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Warning Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Liebert XDP Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
iii
7.7
7.8
7.9
Liebert XDP Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
CANbus Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Network Layout Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
7.9.1
7.9.2
7.10
7.11
CANbus Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Connecting the CANbus Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
7.11.1
7.11.2
7.11.3
7.11.4
7.12
Remote Temperature/Humidity Sensor Placement and Connection to the CANbus . . . . . . 137
CANbus Maximum Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Connection to the Liebert XDP or Liebert XDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to the Liebert XDV Smart Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to the Liebert XDH Smart Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to the Liebert XD Smart modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
140
141
142
143
CANbus Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
7.12.1 Remote Temperature and Humidity Sensors Termination . . . . . . . . . . . . . . . . . . . . . . . . . . 144
7.12.2 Terminating a Smart Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
8.0
MONITORING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
9.0
SPECIFICATIONS AND MODEL NUMBER NOMENCLATURE . . . . . . . . . . . . . . . . . . . . . . . . . 149
FIGURES
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
Figure 19
Figure 20
Figure 21
Figure 22
Figure 23
Figure 24
Figure 25
Figure 26
Figure 27
Figure 28
Figure 29
Liebert XDP generic piping layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Liebert XDC generic piping layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Liebert XDA—air flow enhancer—on equipment enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Liebert XDCF modules on Egenera’s BladeFrame EX cabinets . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Liebert XDH—horizontal cooling module in hot aisle-cold aisle arrangement . . . . . . . . . . . . . . . 5
Suspended Liebert XDO modules in hot aisle-cold aisle arrangement . . . . . . . . . . . . . . . . . . . . . 6
Liebert XDR on cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Top-mounted Liebert XDV modules with hard piping in hot aisle-cold aisle arrangement . . . . . 8
Top-mounted Liebert XDV modules with Liebert Flex Pipe in hot aisle-cold aisle
arrangement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Liebert XD Chiller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Liebert XDP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Liebert XD connection port kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Typical Liebert XDR piping—interlaced connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Liebert XDCF module mounting locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Liebert XDH placement (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Liebert XDO spacing—horizontal (side view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Liebert XDO placement over cold aisle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Generic airflow diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Positioning Liebert XDV on top of cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Liebert XDV modules mounted on racks emitting 3kW of heat, top view . . . . . . . . . . . . . . . . . . 24
Liebert XDV modules mounted on racks emitting 5kW of heat, top view . . . . . . . . . . . . . . . . . . 25
Liebert XDV modules mounted on racks emitting 8kW of heat top view. . . . . . . . . . . . . . . . . . . 25
Liebert XDV modules mounted on racks emitting 16kW of heat top view. . . . . . . . . . . . . . . . . . 26
Multiple Liebert XD modules in an interlaced system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Liebert XD modules not in hot aisle/cold aisle configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Piping for Liebert XDP/Liebert XDC used with Liebert XD cooling modules . . . . . . . . . . . . . . . 27
Generic piping layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Bypass flow controller details, dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Bypass flow controller arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
iv
Figure 30
Figure 31
Figure 32
Figure 33
Figure 34
Figure 35
Figure 36
Figure 37
Figure 38
Figure 39
Figure 40
Figure 41
Figure 42
Figure 43
Figure 44
Figure 45
Figure 46
Figure 47
Figure 48
Figure 49
Figure 50
Figure 51
Figure 52
Figure 53
Figure 54
Figure 55
Figure 56
Figure 57
Figure 58
Figure 59
Figure 60
Figure 61
Figure 62
Figure 63
Figure 64
Figure 65
Figure 66
Figure 67
Figure 68
Figure 69
Figure 70
Figure 71
Figure 72
Figure 73
Figure 74
Figure 75
Figure 76
Figure 77
Figure 78
Figure 79
Bypass flow controller piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General piping details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General piping details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hard-pipe connection diagram for Liebert cooling modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XD return header orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XD supply header orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Efficient piping layout—avoid “bull head T” connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Two-port prefabricated piping for Liebert XD cooling modules . . . . . . . . . . . . . . . . . . . . . . . . . .
Four-port prefabricated piping for Liebert XD cooling modules . . . . . . . . . . . . . . . . . . . . . . . . . .
Five-port prefabricated piping for Liebert XD cooling modules . . . . . . . . . . . . . . . . . . . . . . . . . .
Ten-port prefabricated piping for Liebert XD cooling modules. . . . . . . . . . . . . . . . . . . . . . . . . . .
Piping access points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XD system with CANbus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CANbus cable wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Single daisy chain of Liebert XDO smart modules in CANbus network . . . . . . . . . . . . . . . . . . .
Sensor at the end of daisy chain of Liebert XDO smart modules in CANbus network . . . . . . . .
Sensor within the daisy chain of Liebert XDV smart modules in CANbus network . . . . . . . . . .
Dual daisy chain of Liebert XDV smart modules in CANbus network . . . . . . . . . . . . . . . . . . . .
Independent smart module and sensor daisy chains in CANbus network. . . . . . . . . . . . . . . . . .
Liebert XDCF generic piping layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overall dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDCF module mounting locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDCF supply and return piping access points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDH dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supply and return piping connections—Liebert XDH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Liebert XDH electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Smart Liebert XDH electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low-voltage connections—Liebert XDH smart module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensional data—Liebert XDO hard-piped modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensional data—Liebert XDO with pre-charged option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDO internal mounting location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Top and front electrical access points and terminal block—standard Liebert XDO modules. . .
High-voltage terminal block and connection locations—standard Liebert XDO modules . . . . .
Top and front electrical access points—Liebert XDO smart modules . . . . . . . . . . . . . . . . . . . . .
High-voltage terminal block connection locations—Liebert XDO smart modules. . . . . . . . . . . .
Low-voltage wiring—Liebert XDO smart modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDR dimensions with hard-piped connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDR dimensions with one-shot connections (precharged) . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDR dimensions with removable connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDV dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDV dimensions with one-shot connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Suspending single Liebert XDV from Unistruts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Suspending single Liebert XDV from the roof structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alternate mounting methods—mounting multiple Liebert XDV modules. . . . . . . . . . . . . . . . . .
Electrical connections for CSA-approved Liebert XDV basic modules . . . . . . . . . . . . . . . . . . . . .
Electrical connections for CE-approved Liebert XDV basic modules . . . . . . . . . . . . . . . . . . . . . .
Electrical connections for CSA-approved Liebert XDV smart modules . . . . . . . . . . . . . . . . . . . .
Electrical connections for CE-approved Liebert XDV smart modules . . . . . . . . . . . . . . . . . . . . .
Low-voltage connections for Liebert XDV smart modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensional data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
v
30
31
31
32
33
34
34
35
36
37
38
43
45
45
46
47
47
47
48
49
50
51
52
53
54
55
55
56
58
58
59
60
61
61
62
63
66
67
68
70
71
71
72
73
74
75
76
77
78
80
Figure 80
Figure 81
Figure 82
Figure 83
Figure 84
Figure 85
Figure 86
Figure 87
Figure 88
Figure 89
Figure 90
Figure 91
Figure 92
Figure 93
Figure 94
Figure 95
Figure 96
Figure 97
Figure 98
Figure 99
Figure 100
Figure 101
Figure 102
Figure 103
Figure 104
Figure 105
Figure 106
Figure 107
Figure 108
Figure 109
Figure 110
Figure 111
Figure 112
Figure 113
Figure 114
Figure 115
Figure 116
Figure 117
Figure 118
Figure 119
Figure 120
Figure 121
Figure 122
Figure 123
Figure 124
Figure 125
Figure 126
Figure 127
Figure 128
Figure 129
Piping locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Positioning a water/glycol Liebert XDC for placement on a floor stand. . . . . . . . . . . . . . . . . . . . 82
Piping locations—floor stand and valve assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Front view of Liebert XDC and electrical enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Liebert XDC electrical enclosure knockout locations for field wiring. . . . . . . . . . . . . . . . . . . . . . 84
Liebert XDC high-voltage connections—primary disconnect switch, 60Hz models. . . . . . . . . . . 85
Liebert XDC high-voltage connections—primary disconnect switch, 50Hz models. . . . . . . . . . . 85
Liebert XDC high-voltage connections—secondary disconnect switch, 60Hz models . . . . . . . . . 86
Liebert XDC high-voltage connections—secondary disconnect switch, 50Hz models . . . . . . . . . 86
Liebert XDC heat rejection electrical connection points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Liebert XDC electrical enclosure knockout locations for Extra Low-Voltage connections . . . . . 87
Liebert XDC Extra Low Voltage field connection points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Liebert XDP dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Liebert XDP piping access points and external features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Front view of Liebert XDP and electrical enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Liebert XDP electrical enclosure knockout location for hazardous voltage wiring . . . . . . . . . . . 92
Liebert XDP electrical enclosure knockout locations for field wiring. . . . . . . . . . . . . . . . . . . . . . 93
Liebert XDP high-voltage connections—60Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Liebert XDP high-voltage connections—50Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Condenser planning dimensional data—Four-fan units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Condenser planning dimensional data—Six-fan units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Typical condenser footprint—dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Double discharge riser layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Installation data—Liebert Lee-Temp, one-circuit, four-fan model . . . . . . . . . . . . . . . . . . . . . . . 101
Installation data—Liebert Lee-Temp, one-circuit, high ambient six-fan model . . . . . . . . . . . . 102
Liebert XDC piping schematic and Liebert Lee-Temp heater pad wiring . . . . . . . . . . . . . . . . . 103
General arrangement air-cooled Liebert XDC Liebert Lee-Temp Control. . . . . . . . . . . . . . . . . 104
DCSL616 piping connections—two refrigerant circuits connected for parallel flow . . . . . . . . . 105
DCSL616 piping connections—two refrigerant circuits connected for parallel
refrigerant flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Additional oil requirements for refrigerant charge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Typical piping arrangement for Liebert XDC and two DDNT880A . . . . . . . . . . . . . . . . . . . . . . 111
Drycooler planning dimensional data—Eight-fan units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Typical drycooler footprint—dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Piping connections for 8-fan drycoolers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Flow rate, 10 hp, 3500 rpm pump package, Model # 9A31258G3 in aluminum enclosure . . . . 122
Liebert iCOM display—Liebert XDC and Liebert XDP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Liebert iCOM default home screen for Liebert XDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Liebert iCOM default home screen for Liebert XDP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Cooling module overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Smart module parameters—Liebert XDH, Liebert XDO, Liebert XDV . . . . . . . . . . . . . . . . . . . 127
Liebert iCOM User Menu icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Liebert iCOM Service Menu icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Liebert XD system with CANbus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Modules on a single chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Modules on two chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
CANbus cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
CANbus cable plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
CAN Isolator location within the Liebert XDP/XDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
P2 and P4 locations on the CAN Isolator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Liebert XDV Smart Module CANbus port locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
vi
Figure 130
Figure 131
Figure 132
Figure 133
Figure 134
Figure 135
Figure 136
Figure 137
Figure 138
Figure 139
Figure 140
Liebert XDH CANbus port locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Single-circuited Liebert XDHs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dual-circuited Liebert XDHs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDO CANbus port locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDCF model number nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDH model number nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDO model number nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDR model number nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDV model number nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDC model number nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDP model number nomenclature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
142
143
143
144
149
152
155
156
159
162
164
TABLES
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Table 9
Table 10
Table 11
Table 12
Table 13
Table 14
Table 15
Table 16
Table 17
Table 18
Table 19
Table 20
Table 21
Table 22
Table 23
Table 24
Table 25
Table 26
Table 27
Table 28
Table 29
Table 30
Table 31
Liebert XD field-installed port kits header connection size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum and minimum modules supported by a Liebert XDP or Liebert XDC . . . . . . . . . . . . .
Sample Liebert XD coolant supply loop connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sample Liebert XD coolant supply loop connections, balanced loads . . . . . . . . . . . . . . . . . . . . . .
Calculating quantity and spacing of Liebert XDO modules (example below is Liebert
XDO20) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calculating quantity of Liebert XDR modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Determine required number of Liebert XDV modules (example below is Liebert XDV10) . . . . .
Supply, return pipe sizes for refrigerant loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bypass flow controllers for Liebert XDC- or Liebert XDP-based systems . . . . . . . . . . . . . . . . . . .
Two-port prefabricated piping legend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Four-port prefabricated piping legend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Five-port prefabricated piping legend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ten-port prefabricated piping legend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XD Flex Pipe assemblies, supply and return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System R-134a charge for a Liebert XDP/Liebert XDC with any model Liebert XDH/
Liebert XDO/Liebert XDV/Liebert XDCF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System refrigerant charge for the supply and return mains . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
R-134a refrigerant charge for hard-piped connector lines to and from any model Liebert
XDH/Liebert XDO/Liebert XDV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
R-134a refrigerant charge for Flex Pipe connector lines to and from any model Liebert XDO/
Liebert XDH/Liebert XDV/Liebert XDCF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calculating refrigerant charge—example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Worksheet to calculate refrigerant charge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unit piping outlet connection sizes, inches, OD Cu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CANbus cable part numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Allowable total CAN cable length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cumulative cable length in Figure 44 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cooling capacity, 1500-3000 cfm air flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensional data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDC dimensions, weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XD Chiller dimensions, weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDC piping connection sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDC Water/Glycol Piping Connection Sizes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDP dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
vii
11
16
16
16
21
22
23
28
29
35
36
37
38
39
40
40
41
41
41
42
43
45
46
46
65
70
80
80
81
82
90
Table 32
Table 33
Table 34
Table 35
Table 36
Table 37
Table 38
Table 39
Table 40
Table 41
Table 42
Table 43
Table 44
Table 45
Table 46
Table 47
Table 48
Table 49
Table 50
Table 51
Table 52
Table 53
Table 54
Table 55
Table 56
Table 57
Table 58
Table 59
Table 60
Table 61
Table 62
Table 63
Table 64
Table 65
Table 66
Table 67
Table 68
Table 69
Table 70
Table 71
Table 72
Table 73
Table 74
Table 75
Unit piping outlet connection sizes, inches, OD Cu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Receivers and head pressure kits for Liebert Lee-Temp condensers . . . . . . . . . . . . . . . . . . . . . . . 95
Condenser weights and connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
60Hz electrical condenser data—Liebert Lee-Temp controlled/fan-cycling. . . . . . . . . . . . . . . . . . 98
50Hz condenser full load amp values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Liebert Lee-Temp receiver electrical data, 50Hz and 60Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Receivers and head pressure kits for Liebert Lee-Temp condensers . . . . . . . . . . . . . . . . . . . . . . 100
Recommended refrigerant line sizes, DX R-407C, OD copper . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Recommended refrigerant line sizes for DCSL616 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Indoor unit refrigerant charge—R-407C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Outdoor air condenser charge—R-407C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Air-cooled systems - liquid line charge - R-407C refrigerant per 100ft (30m) of Type ACR
copper tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Indoor water/glycol-cooled module – R-407C refrigerant charge . . . . . . . . . . . . . . . . . . . . . . . . . 108
Standard drycooler net weights, shipping weights, dimensions and volume, approximate . . . . 112
Standard drycooler piping connection sizes and internal volume . . . . . . . . . . . . . . . . . . . . . . . . 114
60Hz electrical values - Eight-fan drycoolers without pump controls, standard models . . . . . . 117
60Hz pump FLA values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Minimum recommended control circuit wire size, AWG, 60 Hz models . . . . . . . . . . . . . . . . . . . 118
Minimum recommended control circuit wire size, mm2, 50Hz models . . . . . . . . . . . . . . . . . . . . 118
Glycol concentrations for freeze protection by ambient temperatures . . . . . . . . . . . . . . . . . . . . 120
Volume in standard Type "L" copper piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Liebert Outdoor Control Enclosure specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
CANbus cable lengths and part numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Liebert XDC/XDP monitoring points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Liebert XD Smart Module monitoring points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
System data points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Communication cards for Liebert XD units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Liebert XDCF specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Liebert XDH20 specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Liebert XDH32 specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Liebert XDO16 specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Liebert XDO20 specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Options for Liebert XDO20 and Liebert XDO16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Liebert XDO dimensions—domestic and export . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Liebert XDR20 specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Liebert XDR rack mounting kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Liebert XDV8 specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Liebert XDV10 specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Liebert XDV dimensions—domestic and export . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Liebert XDC160 specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Floor stand specifications—water-cooled Liebert XDC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Floor stand specifications—Liebert XDC with 40% propylene glycol . . . . . . . . . . . . . . . . . . . . . 161
Floor stand specifications—Liebert XDC with 40% ethylene glycol . . . . . . . . . . . . . . . . . . . . . . 162
Liebert XDP160 specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
viii
System Description
1.0
SYSTEM DESCRIPTION
The Liebert XD™ family of cooling units delivers efficient, sensible cooling to high-heat environments.
Liebert XD systems are designed to cool computer racks and hot zones in a data center or computer
room without taking up expensive floor space for cooling components.
The Liebert XD family includes:
•
•
•
•
•
•
•
•
Liebert XDC™—Liebert XD Chiller; cools and pumps refrigerant to cooling modules
Liebert XDP™—Liebert XD Pumping unit; pumps refrigerant to cooling modules
Liebert XDA™—mounts on the rear of the equipment cabinet
Liebert XDCF™—Liebert XD CoolFrame; mounts on the rear of an Egenera BladeFrame EX
cabinet
Liebert XDH™—Liebert XD Horizontal row cooler; integrated into hot aisle-cool aisle room
layout
Liebert XDO™—Liebert XD Overhead module; suspended from the ceiling structure
Liebert XDR™—Liebert XD Rear cooling module; mounts on the rear of equipment cabinets that
are 24" (600mm) wide and 42U high, approximately 79" (2000 mm)
Liebert XDV™—Liebert XD Vertical module; mounted on top of the equipment cabinet or
suspended from the ceiling structure
Systems combining Liebert XDO, Liebert XDR and Liebert XDV modules can remove more than
20kW (5.7 tons) of heat per cabinet. A set of Liebert XDCF modules also can remove 20kW (5.7 tons)
of heat from an Egenera BladeFrame EX™ cabinet. A system with Liebert XDH modules can remove
more than 30kW (8.5tons) of heat per rack.
For minimum Liebert XDP and Liebert XDC load recommendations, see 1.10.1 - Liebert XDP
Minimum Load; 1.9.1 - Liebert XDC Minimum Load; and Tables 71 and 75.
The Liebert XD system also performs at high efficiency rates. Properly spaced cooling modules and
the Liebert XD system’s fluid phase change technology, combine to reduce a Liebert XD system’s
energy consumption to at least 27 percent less than a traditional cooling system.
The Liebert XD family maintains this energy efficiency by employing the heat absorption properties
of a liquid (pumped refrigerant) through a phase change. Refrigerant is pumped as a liquid, becomes
a gas within the heat exchangers of the cooling modules (either the Liebert XDCF, Liebert XDH,
Liebert XDO, Liebert XDR or Liebert XDV) and then is returned to either the Liebert XDP or Liebert
XDC where it condenses to a liquid. This eliminates the compression cycle required by traditional
systems. And, if a leak were to occur, the environmentally friendly refrigerant in the data center
would escape as a gas, causing no harm to critical equipment. Because no compressor is used in the
pumped refrigerant circuit, no oil is needed.
Liebert XD cooling modules further increase efficiency with optional control board that reduces fan
use when maximum cooling levels are not required. The control board is available on Liebert XDH,
Liebert XDO and Liebert XDV modules.
1.1
European Union Fluorinated Greenhouse Gas Requirements
Stationary air conditioning, refrigeration, heat pump equipment and stationary fire protection
systems in the European Community market and operating with fluorinated greenhouse gases (fgas), such as R407C, R134a, R410A, must comply with the F-Gas Regulation: (EC) No. 842/2006 (Fgas). The regulation prohibits, among other actions, venting fluorinated greenhouse gases to the
atmosphere.
The F-Gas Regulation requires operators to use all measures that are technically feasible and do not
entail disproportionate cost to prevent leakage of these gases, to test for leakage regularly and to
recover f-gas before disposing of equipment, as well as during service and maintenance.
Refer to the full regulation for additional details.
1
System Description
1.2
Generic Piping Layouts
Liebert XD systems are available in two configurations—differentiated essentially by the method of
heat rejection (see Figures 1 and 2). The Liebert XDP is a pumping unit connected to a building
chilled water system to control and circulate the refrigerant. Liebert XDPs pump refrigerant to
Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR or Liebert XDV modules, isolate refrigerant
circuit from building chilled water supply with an internal heat exchanger and maintains refrigerant
temperature above the actual dew point. The Liebert XDC incorporates the pumping functions with
the chiller, which must be connected to a separate heat rejection system. Pumping and refrigerant
control are performed by Liebert XDC.
Figure 1
Liebert XDP generic piping layout
Liebert XDP System Configuration
Liebert
XDP
Building
Chilled
Water
Pumped
Refrigerant
R134a
Liebert
XDP
Figure 2
Pumped
Refrigerant
R134a
* Liebert XD
Cooling Module
* Liebert XD
Cooling Module
* Liebert XD
Cooling Module
Supply Piping
Return Piping
* Liebert XDCF,
Liebert XDH, Liebert
XDO, Liebert XDR or
Liebert XDV
Liebert XDC generic piping layout
Liebert XDC System Configuration
Liebert Heat
Rejection
Air-Cooled or
Water/Glycol Cooled
Liebert XDC
R407C
Pumped
Refrigerant
R134a
Liebert XDC
R407C
Pumped
Refrigerant
R134a
Liebert XD
Cooling Module*
Liebert XD
Cooling Module*
Return Piping
Liebert XD
Cooling Module*
Liebert XD
Cooling Module*
2
Supply Piping
* Liebert XDCF,
Liebert XDH, Liebert
XDO, Liebert XDR or
Liebert XDV
System Description
1.3
Liebert XDA—Air Flow Enhancer
The Liebert XDA is a fan unit that boosts the airflow through densely populated enclosures, removing
hot spots from within the racks. One or two units can be mounted on the rear of most rack enclosures.
Figure 3
Liebert XDA—air flow enhancer—on equipment enclosure
3
System Description
1.4
Liebert XDCF—Liebert XD CoolFrame
The Liebert XDCF is a self-contained module designed to cool Egenera’s BladeFrame EX cabinets and
equipment without exhausting heat into the room. Two modules (top and bottom) may be mounted on
the rear of a BladeFrame cabinet. Liebert XDCF modules consist of a sheet-metal frame, coil and
filter dryer. It has no moving parts and needs no electricity.
The module is available with optional, Liebert XD Flex Pipes (flexible metal pipes) with quick-connect
couplings at each end for easy connection to the refrigerant distribution pipes.
Figure 4
Liebert XDCF modules on Egenera’s BladeFrame EX cabinets
4
System Description
1.5
Liebert XDH—Horizontal Cooling Module
The Liebert XDH is designed for placement within a row of computer cabinets in the data center in a
hot-aisle-cold-aisle arrangement to maximize the Liebert XDH’s cooling. The Liebert XDH, available
in a half-rack-width module (12" [305mm]), is intended for use with a Liebert XD pumped refrigerant
cooling system, supplied by either a Liebert XDP or Liebert XDC. The module takes in hot air through
the rear from the hot aisle, cools the air by air-to-fluid heat exchangers and discharges the air
through the front of the module into the cold aisle in a diffuse pattern. The cooling air is then drawn
into the enclosures to cool the equipment.
Replaceable front panels on the Liebert XDH may be customized to match the appearance of various
computer manufacturer’s equipment, allowing the Liebert XDH to blend in with adjacent server
equipment and enclosures. Unidirectional and bidirectional diffusers are available to direct cooling
air for more efficient cooling, depending on the Liebert XDH’s positioning in a row or at the end of a
row. Chilled R-134a refrigerant is provided to the Liebert XDH by a Liebert XDP or by a Liebert XDC.
The Liebert XDH has dual refrigeration circuits, one in the upper half of the module and the other in
the lower half. This permits increasing and decreasing cooling levels in response to server room
conditions. The dual refrigeration circuits permits interlaced connection of two Liebert XD refrigerant
sources to enhance system reliability. The Liebert XDH may be installed in a Liebert XD piping
system that includes other Liebert XD cooling modules.
Controls on the front of the Liebert XDH permit independent operation of the two banks of fans. Dual
power connections ensure continued fan operation if one of two electrical sources fails. Optional smart
modules allow remote shutdown, fan failure alarms, condensate detection and switching fan per bank
On and Off. This saves energy by permitting the module to run with two fans per bank and switching
on the middle when the temperature requires all fans for cooling.
The Liebert XDH is available for hard-piped configurations and with flexible metal pipes with
quick-connect couplings (one-shot or removable) at each end for easy connection to the header system.
The Liebert XDH and Liebert XD Flex Pipes are also available for shipment with a pre-charge of
R134a. This option requires the use of the one-shot flexible pipes.
Figure 5
Liebert XDH—horizontal cooling module in hot aisle-cold aisle arrangement
5
System Description
1.6
Liebert XDO—Overhead Cooling Module
The Liebert XDO is an overhead cooling system designed for installation above heat-dissipating
equipment. A fan draws hot air exhausted from the equipment through two cooling coils and
discharges cool air back down to the equipment (see Figure 6).
A Liebert XDO smart module will allow remote monitoring, shutdown, fan failure alarms, condensate
detection and automatically cycling the fan On and Off as the heat load requires. The Liebert
XDP/Liebert XDC monitors room conditions and prevents coil condensation by maintaining the
temperature of the refrigerant pumped to the Liebert XDOs above the room dew point.
The Liebert XDO is available for hard-piped configurations or with Liebert XD Flex Pipes with quickconnect couplings (one-shot) for easy connection to the header system. When the pre-charged option is
selected, the Liebert XDO and the one-shot flexible pipes contain R134a.
NOTE
The Liebert XDO is the most sensitive module to system load. The Liebert XDO’s air intake and
the discharge are not separated by a rack. This can lead to the Liebert XDO pulling in cold air
rather than hot air. The Liebert XDP and Liebert XDC minimum loads must be met to prevent
this from occurring.
Figure 6
Suspended Liebert XDO modules in hot aisle-cold aisle arrangement
Cold Aisle
Hot Aisle
Cold Aisle
Hot Aisle
6
Cold Aisle
System Description
1.7
Liebert XDR—Rear Cooling Module
The Liebert XDR is a cooling system for high-density heat loads that mounts on the rear of a 24"
(600mm) x 42U rack (consult the factory for other rack sizes) and maintains access to the back of the
server rack. Room air is drawn in through the front of the rack and picks up heat from the servers.
The coil captures that heat, cooling the air, which is expelled through the rear of the rack.
The Liebert XDR relies on the rack equipment’s fans to move air across the microchannel coil.
Captured heat is carried away through pumped R-134a refrigerant supplied by either a Liebert XDP
or Liebert XDC.
The Liebert XDR is available in hard-piped configurations or with Liebert XD Flex Pipes with
quick-connect couplings (one-shot or removable) for easy connection to the header system. The Liebert
XDR and flexible pipes are also available pre-charged with R134a refrigerant. This option requires
the one-shot connections.
Figure 7
Liebert XDR on cabinet
7
System Description
1.8
Liebert XDV—Vertical, Above-Cabinet Cooling Module
The Liebert XDV cooling system is designed to be attached to the top of a computer cabinet or rack
containing heat-dissipating equipment. Two fans draw hot air exhausted from the equipment or from
the hot aisle, pass it through a cooling coil and discharge cool air back down to the cold aisle, where
the equipment's air intake is located.
The Liebert XDV comes from the factory ready to draw heated air through a perforated grille on the
back of the module. The Liebert XDV is easily modified to draw hot air through the bottom of the
module, should that cooling method be better suited to your application.
Liebert XDV smart modules allow remote shutdown, fan failure alarms and automatically switching
the second fan On and Off. This saves energy by permitting the module to run with one fan and
switching on a second fan when the temperature requires both fans for cooling.
The Liebert XDV is available for hard-piped configurations or with Liebert XD Flex Pipes with quickconnect couplings (one-shot or removable) for easy connection to the header system. The Liebert XDV
and flexible pipes are also available for shipment with a pre-charge of R134a. This option requires the
use of the one-shot flexible pipes
Figure 8
Top-mounted Liebert XDV modules with hard piping in hot aisle-cold aisle
arrangement
Cold
Aisle
Figure 9
Hot
Aisle
Cold
Aisle
Hot
Aisle
Cold
Aisle
Top-mounted Liebert XDV modules with Liebert Flex Pipe in hot aisle-cold aisle
arrangement
Cold
Aisle
Hot
Aisle
Cold
Aisle
8
System Description
1.9
Liebert XDC—Refrigerant Chiller
The Liebert XDC is an indoor chiller that connects directly to the Liebert XD cooling modules and
provides refrigerant circulation and control. The Liebert XDC keeps the refrigerant temperature
above the room dew point at the sensors. The Liebert XDC contains a refrigerant to refrigerant heat
exchanger along with two tandem scroll compressor circuits. This allows heat rejection to the outdoor
ambient air by using either the air-cooled condensers or water/glycol shell-and-tube condensers much
like a standard computer room air conditioning unit. The Liebert XDC employs two remote sensors
(for redundancy) to determine the temperature and humidity in the air and instantly adjusts
refrigerant supply temperature to compensate for changing conditions.
The Liebert XDC uses the Liebert iCOM®. This advanced control enables the user to monitor
essentially all aspects of the Liebert XD Precision Cooling system, from operating status to
maintenance
1.9.1
Liebert XDC Minimum Load
The Liebert XDC’s minimum recommended operating load is 40% of system nominal capacity. For
example, a Liebert XDC160 60Hz system’s minimum load would be 64 kW. Loading below this value
can unfavorably affect system operation.
Figure 10
Liebert XD Chiller
9
System Description
1.10
Liebert XDP—Pumping Unit
The Liebert XDP isolates the building’s chilled water circuit from the pumped refrigerant circuit. The
Liebert XDP circulates refrigerant to Liebert XD cooling modules while preventing condensation by
maintaining the refrigerant’s temperature above the room dew point at the sensors. The Liebert XDP
employs two sets (for redundancy) of remote sensors to determine the temperature and humidity in
the air and instantly adjusts refrigerant supply temperature to compensate for changing conditions.
The Liebert XDP uses the Liebert iCOM. This advanced control enables the user to monitor
essentially all aspects of the Liebert XD Precision Cooling system, from operating status to
maintenance.
1.10.1 Liebert XDP Minimum Load
The Liebert XDP’s minimum recommended operating load is 30% of system nominal capacity. For
example, a Liebert XDP160 60Hz system’s minimum load would be 48 kW. Loading below this value
can unfavorably affect system operation.
Figure 11
1.11
Liebert XDP
Liebert XD Piping
Liebert XD Piping is prefabricated distribution piping that is installed in anticipation of a growing
system. Liebert XD cooling modules are added as required and are quickly made operational with
flexible connection piping with threaded couplings. This unique system allows the room cooling
capacity to increase to more than 30kW per rack with no additional disruptive piping installation.
The flexible connection piping also allows the cooling modules to be re-positioned without
interruption in operation.
10
System Description
1.11.1 Liebert XD Field Piping
Flexible Piping Kit
Flex pipe kits are available in lengths of 4, 6, 8 and 10 feet (1.2, 1.8, 2.4 and 3 meters). Connection
style to the module end may be straight or 90 degrees with one-shot style couplings or removable
couplings. The one-shot flexible pipes are charged at the factory with R134a. Connection to the
prefabricated piping assembly is a threaded coupler. For information on acquiring the correct kit for
your installation refer to DPN000780, available by calling 1-800-LIEBERT and from your local
Emerson Network Power representative. Contact the factory when ordering additional flex piping
kits for Liebert XD systems installed before 2007.
Prefabricated Headers
Field piping kits are available in several versions
• 10 ft. (3.05m) with 5 or 10 ports
• 8 ft. (2.44m) with 2 or 4 ports
Each version is available in two pipe sizes:
• Supply pipe: 1-1/8"; return pipe: 2-1/8"
• Supply pipe: 1-3/8"; return pipe: 2-5/8"
Each kit contains one (1) supply pipe and one (1) return pipe. Each port has a threaded coupling at
the end with automatic shutoff when disconnected. Each port also has a ball valve for manual shutoff.
For more information refer to section 3.13 - Liebert XD Piping System Design.
Liebert XD Connection Port Kit
The connection ports in the Liebert XD Field Piping Kits are available as Liebert XD Connection Port
Kit. Each port has a threaded coupling, with automatic shutoff when disconnected, at the end. Each
port also has a ball valve for manual shutoff. Each kit contains one supply and one return port. Two
kit sizes are available:
• Supply pipe: 1-1/8"; return pipe: 2-1/8"
• Supply pipe: 1-3/8"; return pipe: 2-5/8"
Figure 12
Liebert XD connection port kit
Return valve shown
Supply valve appearance
is similar, but is smaller
Table 1
Liebert XD field-installed port kits header connection size
Assembly P#
Supply Header
Diameter
Return Header
Diameter
183169G3
183169G4
1-1/8"
1-3/8"
2-1/8"
2-5/8"
11
Starting a New Equipment Cooling Project
2.0
STARTING A NEW EQUIPMENT COOLING PROJECT
2.1
Determining Cooling Equipment Needs
2.2
1.
Is adequate space available for a Liebert XD installation?
2.
Is the hot aisle/cold aisle approach being utilized for this room design or can it
be utilized in this room design?
3.
Is redundant cooling equipment required?
4.
Are there access considerations for all components (possible rigging problems)
5.
What heat load growth is anticipated over the next few years?
6.
How are the cabinets going to be populated (density of heat generation)?
7.
What monitoring requirements are desired or needed?
8.
Who will be involved in this project (stakeholders)?
9.
Is there existing computer room environmental cooling systems for humidity
control and filtration?
10.
Is the vapor barrier sufficient?
11.
Is a chilled water system available?
a.
What is the system’s capacity?
b.
What is the system’s chilled water supply temperature?
c.
Does the chilled water supply temperature vary during the year or is the
temperature constant?
12.
How much power is available for cooling equipment?
13.
What is the maximum distance between the Liebert XDP/Liebert XDC unit
and the farthest Liebert XD cooling module in the proposed layout?
14.
If an air-cooled Liebert XDC is used—is an area available for the remote
condenser?
15.
Does the Liebert XD system refrigerant volume exceed 13 lb/1000ft3? If so, a
refrigerant detection and removal equipment may be required. Refer to 3.22 Liebert XD Refrigerant.
Implementing a Hot-Aisle/Cold Aisle Design
A best practice is to place equipment racks in alternating rows of cold aisles and hot aisles. This is
best accomplished when the layout of the file-server farm area is being planned. It is more difficult to
accomplish when the computer room is already populated with operating hardware.
In the cold aisle, the equipment racks are arranged face-to-face so the cooling air from the computer
room cooling unit discharged up through the perforated floor tiles is drawn into the face of the
computer hardware and exhausted out the back of the equipment rack into the adjacent hot aisles.
Hot aisles are literally hot because the objective of the alternating cold and hot aisle design is to
separate the source of cooling air from hot air discharge, which returns to the computer-room cooling
unit. Therefore, no perforated tiles should be placed in the hot aisles. This would mix hot and cold air,
lowering the temperature of the air returning to the cooling units, reducing their usable capacity.
12
Designing a Liebert XD Solution
3.0
DESIGNING A LIEBERT XD SOLUTION
Liebert XD systems are intended for use with precision air conditioning equipment, such as the
Liebert Deluxe System/3 and Liebert DS™. The precision air conditioning equipment is required for
the humidification and filtration of the room air.
The Liebert XD systems provide efficient, highly effective heat removal (sensible cooling only),
without providing humidity control. The Liebert XD control system maintains the refrigerant
temperature just above the dew point of the space to prevent condensation. Since the capacity of the
system is limited by the dew point in the space, sufficient dehumidification and an adequate vapor
barrier must be provided to maintain the dew point at or below the level necessary to achieve the
required capacity.
The Liebert XD system is optimized for hot aisle/cold aisle equipment configurations, an industry best
practice for dealing with extremely high heat loads. Room and equipment designs that preclude the
hot aisle/cold aisle configuration are often well-suited to cooling with the Liebert XDR system.
Refer to the technical data manual of either the Deluxe System/3 (SL-18100) or the
Liebert DS (SL-18810) for additional installation and application guidelines that apply to all critical
space cooling applications.
3.1
Determine Cooling Requirements and Select Liebert XD System
1.
2.
3.
4.
5.
3.2
Calculate the total cooling required
Determine placement of the Liebert XD modules
Determine required pipe sizes
Calculate the refrigerant volume of the Liebert XD systems
Complete design details including, electrical, mounting, piping, etc.
Calculate the Heat Load to be Handled by Liebert XD System
When designing a cooling solution using the Liebert XD system, the initial steps are similar to those
required to cool a conventional critical space. The total heat load must be calculated, including
sensible and latent cooling requirements. These should be increased by the reserve capacity needed
for pull-down situations where the room temperature must be reduced and to provide for unexpected
increases in heat load.
NOTE
Reserve capacity is distinct from redundant capacity in that redundant capacity may or may
not be available concurrently with normal operating capacity. Reserve capacity is available
concurrently with normal operating capacity.
The next step is to determine how much of the required cooling capacity is to be provided by Liebert
Deluxe™ or Liebert DS units. If the facility is new, typically up to 150W/ft2 (1500W/m2) of cooling can
be obtained from Liebert precision air conditioning units supplying air through a raised floor. In
existing facilities, such factors as raised floor height, under-floor obstructions or other limitations
may reduce this to less than 50W/ft2 (500W/m2).
Once the total required sensible cooling capacity is known, subtract the sensible cooling portion to be
provided by Liebert Deluxe or Liebert DS units. This yields the cooling capacity to be provided by the
Liebert XD system. Confirm the minimum heat load for the Liebert XDP/Liebert XDC is still present
in the data center (48kW and 64kW respectively).
13
Designing a Liebert XD Solution
Example
For example, a 2000 ft2 server room with has 30 racks, 15 racks produce 20kW of heat each and 15
produce 10kW of heat per rack.
1. Calculate the total sensible cooling load.
15 racks x 20kW/rack = 300kW
15 racks x 10kW/rack = 150kW
300kW + 150kW = 450kW
The total room load is 450kW.
2. Check heat density per square foot:
450kW/2000ft2 = 0.225kW/ft2 = 225W/ft2
3. Determine base cooling requirements:
Typically, perimeter cooling accounts for 2 to 5kW per rack.
2kW x 30 racks = 60kW
Based on 2kW/rack, 60 kW will be handled by the perimeter cooling.
4. Determine Liebert XD cooling requirements:
450kW - 60kW = 390kW
Three Liebert XDP160s would be needed.
5. Calculate the Liebert XDP reserve capacity:
390kW/3 Liebert XDP160s = 130kW
Each Liebert XDP, on average, would bear 130kW of the heat load.
130kW / 160kW = 81% of maximum load
This Liebert XD solution has 19% reserve capacity.
14
Designing a Liebert XD Solution
3.3
Selecting Liebert XD Cooling Modules
The next step is to select the Liebert XD cooling modules to be configured into the solution. Liebert
XD modules that use pumped refrigerant can be connected to the same Liebert XDP/Liebert XDC
piping circuit. This includes the Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and
Liebert XDV.
Generally, the Liebert XDO is selected for use in new installations or renovations where the module
can be installed on the ceiling or in the overhead space.
The Liebert XDV is designed to permit mounting directly on top of an equipment cabinet, for ease of
installation in existing facilities. The Liebert XDV may also be suspended from overhead, using
suitable mounting methods.
The Liebert XDCF is a self-contained module designed to cool Egenera’s BladeFrame EX cabinets and
equipment without exhausting heat into the room. Two modules may be mounted on the rear of a
BladeFrame cabinet.
The Liebert XDH is installed among equipment cabinets and is particularly suited for new
installations.
The Liebert XDR replaces the rear door of an equipment cabinet.
Example
Continuing the preceding data center example (in 3.2 - Calculate the Heat Load to be Handled
by Liebert XD System) of a server room 2000 ft2 with 30 racks (15 producing 20kW of heat per rack
and 15 producing 10 kW of heat per rack), the three Liebert XDPs required can supply coolant to
various types of Liebert XD modules. For instance, the racks with 20kW per rack could be cooled with
either Liebert XDH20, Liebert XDO20 or Liebert XDR20. The racks with 10kW per rack could be
cooled using the Liebert XDV10.
1. For the 15 racks with 20kW of heat each, the total load is:
15 racks x 20kW per rack = 300kW
The perimeter cooling will address the first 2-5kW per rack:
2kW x 15 racks = 30kW
The Liebert XD solution would have to remove 270kW for these racks with higher heat load.
300kW - 30kW = 270kW
Module
Conditions
°F (°C)
Capacity at
Conditions, kW
Load,
kW
Modules
Required
Liebert XDH20
Liebert XDO20
Liebert XDR20
98 (36.6)
98 (36.6)
98 (36.6)
22.0
22.5
22.0
270
270
270
13
12
15
2. For the 15 racks with 10kW of heat each, the total load is:
15 racks x 10kW per rack = 150kW
The base cooling will address the first 2-5kW/rack:
2kW x 15 racks = 30kW
The Liebert XD solution would have to remove 120kW for these racks with a higher heat load.
150kW - 30kW = 120kW
Module
Conditions
°F (°C)
Capacity at
Conditions, kW
Load,
kW
Modules
Required
Liebert XDV10
98 (36.6)
10.0
120
12
3. For this data center example, the Liebert XD solution would consist of:
• 3 Liebert XDP160s
• 12 Liebert XDV10s
and any of the following:
• 13 Liebert XDH20s
• 12 Liebert XDO20s
• 15 Liebert XDR20s
15
Designing a Liebert XD Solution
3.4
Configuring a Liebert XD System
3.4.1
Number of Modules Supported by a Liebert XDP or Liebert XDC
The numerals designating the model size of a Liebert XD module may be used to configure a cooling
system. For example, a Liebert XDO20 has a model size of 20 and a Liebert XDP160 will
accommodate cooling modules with a cumulative model size of 160.
Similarly, the minimum number of modules connected to a Liebert XDP or Liebert XDC may be calculated
using the model size number for the Liebert XDP or Liebert XDC and the modules. See Table 2.
Table 2
Maximum and minimum modules supported by a Liebert XDP or Liebert XDC
Liebert XDC
Liebert XDP
Max
Min
Max
Min
Liebert XDCF10
Liebert XDH20
16
8
6
4
16
8
5
3
Liebert XDH32
Liebert XDO16
Liebert XDO20
Liebert XDR20
5
10
8
8
2
4
4
4
5
10
8
8
2
3
3
3
Liebert XDV8
Liebert XDV10
20
16
8
7
20
16
6
5
Cooling Module Type
Different types of Liebert XD cooling modules may be connected to the same Liebert XDP or Liebert
XDC as long as the sum of their cooling capacity does not exceed the supporting Liebert XDP’s or
Liebert XDC’s model size number.
Example
Continuing the example in 3.3 - Selecting Liebert XD Cooling Modules, the Liebert XD solution
in that example consisted of:
• Three (3) Liebert XDPs and
• 12 Liebert XDV10s
and any of the following:
• 13 Liebert XDH20s
• 12 Liebert XDO20s
• 15 Liebert XDR20s
1. Using the Liebert XDH20 to continue with the example, the Liebert XD systems could be
populated so that the modules were on dedicated Liebert XDPs.
Table 3
Sample Liebert XD coolant supply loop connections
Liebert XD Loop
Liebert XDP 1
Liebert XDP 2
Liebert XDP 3
Liebert XDH20
Liebert XDV10
Maximum Loop Load, kW
7 modules
6 modules
0 modules
0 modules
0 modules
12 module
154
132
120
2. Another possibility would be to mix the Liebert modules in a manner that allows each Liebert
XDP to have similar loads.
Table 4
Sample Liebert XD coolant supply loop connections, balanced loads
Liebert XD Loop
Liebert XDP 1
Liebert XDP 2
Liebert XDP 3
Liebert XDH20
Liebert XDV10
Applied System Load, kW*
4 modules
4 modules
5 modules
5 modules
5 modules
2 module
138
138
130
*Note: An individual Liebert XDP160 or Liebert XDC160 can remove up to 160kW. The 160kW
can be removed by the various modules whose individual capacities may vary based on the data
center conditions, such as the entering air temperatures or entering refrigerant temperature.
For the Liebert XD system examples above, additional modules may be added as heat loads
increase until the 160kW maximum is reached. The Liebert XDP 3 in the example in Table 4,
which has a load of 130kW, could accept modules that would remove 30kW: one Liebert XDH20
and one Liebert XDV10.
16
Designing a Liebert XD Solution
3.4.2
System Connection Configuration
If possible, connect the Liebert XD modules to Liebert XDPs or Liebert XDCs in an interlaced
configuration (see Figure 13). In an interlaced configuration, half the cooling modules in an aisle are
connected to one Liebert XDP or Liebert XDC and the other half in that aisle are connected to another
Liebert XDP or Liebert XDC. Interlacing the connection piping will keep half the Liebert XD modules
operating and maintain cooling in the conditioned space should one of the Liebert XDP or
Liebert XDC units fail.
Figure 13 Typical Liebert XDR piping—interlaced connections
TOP VIEW
DRAWING IS
NOT TO SCALE
Liebert
XD Module A
Liebert
XD Module B
Liebert
XD Module A
Liebert
XD Module B
Liebert
XD Module B
Liebert
XD Module A
Liebert
XD Module B
Liebert
XD Module A
Liebert XDP /
Liebert XDC A
Supply
Return
Return
Supply
Liebert XDP /
Liebert XDC B
NOTE: Line size does NOT
indicate pipe size difference .
3.5
Airflow Requirements for Liebert XD Solutions
Computer manufacturers typically specify a temperature change from intake to exhaust (delta T) of
18-27°F (10-15°C) for the air passing through a rack enclosure. The heat generated by electronic
equipment combined with the tight quarters of equipment cabinets mean high volumes of air must
move through an enclosure to meet this cooling specification.
A Liebert XD system can supply the cold air to satisfy this cooling demand, but airflow through the
enclosure must be adequate to extract the heat from the cabinet. Liebert’s XDA units can boost the
airflow to levels necessary to protect critical equipment. The Liebert XDA is particularly suited to the
hot aisle/cold aisle arrangement.
17
Designing a Liebert XD Solution
3.6
Liebert XDCF Placement
The Liebert XDCF is a self-contained module designed to cool Egenera’s BladeFrame EX cabinets and
equipment. Liebert XDCF modules attach to the rear of the Egenera BladeFrame EX cabinet, beside
the power modules (see Figure 14). No cutting or drilling is required to attach the modules; all
mounting holes, slots and pins required are fabricated at the factory. The Liebert XDCF does not
require electrical connections.
The number of Liebert XDCF modules required is determined by the heat load of the cabinet—
cabinets cannot share cooling from a Liebert XDCF module.
The Egenera BladeFrame EX cabinet has provisions for mounting two Liebert XDCF modules, should
the heat load require two modules. If only one Liebert XDCF will be needed, Liebert recommends
using the lower Liebert XDCF module.
The complete system consists of Liebert XDCF modules, piping, Liebert XDP or Liebert XDC
refrigerant distribution units and those units’ chillers or drycoolers.
Figure 14 Liebert XDCF module mounting locations
Liebert XDCF Modules
attached to
Egenera BladeFrame EX Cabinet
Upper Module
Lower Module
18
Designing a Liebert XD Solution
3.7
Liebert XDH Placement
The free-standing Liebert XDH cooling module is best placed among the equipment cabinets in a
hot aisle-cold aisle arrangement (see Figure 15). The Liebert XDH draws in air from the hot aisle,
cools it and discharges the cooled air into the cold aisle where it is drawn into the equipment cabinets.
Even spacing aids in optimizing cooling.
Liebert XDH modules should be placed among the cabinets that generate the greatest amount of heat.
If heat loads are dispersed evenly throughout the room, the Liebert XDH modules may be spread out
accordingly. Bi-directional air diffusers should be used on Liebert XDH modules installed between
racks.
If a Liebert XDH is installed at the end of a row, uni-directional air diffusers should be used on that
Liebert XDH. The uni-directional diffusers can be used for left or right air discharge by removing
them from the Liebert XDH, turning them 180 degrees, then reattaching them to the Liebert XDH.
Figure 15
Liebert XDH placement (top view)
Hot
Aisle
Liebert XDH
Liebert XDH
Liebert XDH
Liebert XDH
Cold
Aisle
Liebert XDH
Liebert XDH
Liebert XDH
Liebert XDH
Hot
Aisle
19
Liebert XDH
Liebert XDH
Liebert XDH
Liebert XDH
Cold
Aisle
X
D
H
Designing a Liebert XD Solution
3.8
Liebert XDO Placement
3.8.1
Determining Spacing of Liebert XDOs in an Aisle
Liebert XDO modules should be placed in rows directly above the cold aisles of a room for optimum
cooling. Each Liebert XDO serves an area equal in width to the cold aisle spacing, typically 12 to 16
feet (3.7 to 4.9m). The length of the area served includes any space between Liebert XDO modules in
a row. Depending on the cooling capacity to be achieved, spacing between Liebert XDO modules in a
row may vary from zero to as much as 6 feet (1.8m). When the spacing increases to more than 6 feet
(1.8m), overall performance of the system may be negatively affected and gaps in cooling may occur.
Install one Liebert XDO at the end of each aisle being cooled and to space the remainder between
these end modules as shown in Figure 16. This layout will block the incursion of hot air around the
side of the end cabinets. Allowing space between the Liebert XDO groups facilitates maintenance by
allowing access to the overhead space.
Figure 16
Liebert XDO spacing—horizontal (side view)
Front-to-rear spacing of pairs
of Liebert XDO modules
Pairs of Liebert XDO modules
above critical equipment
XDO height above
equipment to be cooled
Heat-Generating Critical Equipment
20
Designing a Liebert XD Solution
3.8.2
Determining Vertical Placement of Liebert XDOs Above the Cold Aisle
In the maximum density configuration, Emerson recommends placing the Liebert XDOs between 18
and 24 inches (457-609mm) above the equipment cabinets. In some cases where the required density
is less, the front-to-rear spacing of Liebert XDOs in a row will be increased. To ensure coverage of the
wider spaces between the Liebert XDO modules, the vertical distance between the cabinets and the
Liebert XDOs should be increased. However, the recommended maximum height of the Liebert XDO
above the cabinets is 30 inches (762mm). See Figure 17.
Figure 17 Liebert XDO placement over cold aisle
Hot air is
drawn into
the XDO for
cooling
Hard-Piped
Connection
One-Shot
Connection
18-24"
(45.7-60.9mm)
30" max
18-24"
(45.7-60.9mm)
30" max
Critical
Equipment
Critical
Equipment
Critical
Equipment
Cooled air
enters the
rack
4' *
(1.2m)
COLD AISLE
Critical
Equipment
Cooled air
enters the
rack
Hot air goes
into the hot
aisle
3' *
(.91m)
HOT AISLE
Hot air goes
into the hot
aisle
4' *
(1.2m)
COLD AISLE
Cold Aisle
Spacing
* Nominal Distance
Table 5 can be used to determine the correct number and spacing of Liebert XDOs.
Table 5
Calculating quantity and spacing of Liebert XDO modules (example below is Liebert XDO20)
Input Information
Total heat load in the room, kW
Reserve capacity needed
(10% to 25% of A is recommended)
Step
A
B
C
Existing/planned Liebert Deluxe/Liebert DS unit
sensible capacity, kW
F
G
Spacing of cold aisles, center-to-center,
typically 12-16 ft (3.7 to 4.9m)
Required cooling capacity, kW = A + B
D
E
Room area, square feet
Result
H
I
Required Liebert XD system cooling capacity, kW = C – D
Number of Liebert XDO20s required = E ÷ 20, rounded up (60Hz)
= E ÷ 16, rounded up (50Hz)
Number of Liebert XDP/Liebert XDC units required = F ÷ 8,
rounded up (60Hz and 50Hz)
Area served by each Liebert XDO20 = H ÷ F
J
K
L
Spacing between each Liebert XDO = (I ÷ J) - 2
Required Liebert XD system cooling density = E x 1000 ÷ H
OK if under 640; otherwise, additional cooling is required from
Liebert Deluxe or Liebert DS units.
21
Designing a Liebert XD Solution
3.9
Liebert XDR Module Placement
The Liebert XDR does not require a hot aisle/cold aisle arrangement for effective and efficient
operation. Refer to site-specific drawings for exact placement.
The Liebert XDR is engineered to fit the rear of computer enclosure cabinets.
Ensure that there is 25.6" (649mm) clearance in the rear to allow the door to open fully.
3.9.1
Airflow
The server fans draw air into the equipment enclosure. After heated the air, the server fans force the
air across the Liebert XDR’s two coils. The Liebert XDR has a low air-side pressure drop (similar to a
rack with perforated doors). The server fans within the rack create sufficient airflow to move the air.
Figure 18 Generic airflow diagram
Enclosure /Rack
Shown from Side
Refrigerant
Connections
Liebert XDR
Critical
Equipment
Front
of
Rack
Rear
of
Rack
Efficient cooling of rack equipment depends on proper use of blanking plates in any voids in the rack
and good cable management. Refer to the user manual supplied with the rack where the Liebert XDR
is mounted. Keep the Liebert XDR’s coils clear of any obstructions that might block the airflow.
Each of the Liebert XDR’s coils removes approximately half the load. For even cooling in partially
filled racks, servers should be evenly spaced and blanking plates should be installed on unused rack
spaces to prevent recirculation of heated air. The top and bottom of the rack must be sealed with floor
and ceiling panels. Not installing the panels will drastically reduce the Liebert XDR’s performance.
Table 6
Calculating quantity of Liebert XDR modules
Input Information
Step
Total heat load in the room, kW
A
Reserve capacity needed (10% to 25%
of A is recommended)
B
C
Existing/planned Liebert Deluxe/Liebert
DS unit sensible capacity, kW
Result
Required cooling capacity, kW = A + B
D
E
Required Liebert XD system cooling capacity, kW = C – D
F
Number of Liebert XDR20s required = E ÷ 20, rounded up
G
Number of Liebert XDP/Liebert XDC modules required = F ÷ 8,
rounded up
22
Designing a Liebert XD Solution
3.10
Liebert XDV Module Placement
Liebert XDV modules should be placed on top of the cabinets that generate the greatest amount of
heat. If heat loads are dispersed evenly throughout the room, the Liebert XDV modules may be
spread out accordingly.
The Liebert XDV must be placed toward the front of the equipment cabinet, so that its front bottom
edge is flush with the front top edge of the cabinet. Placing the module farther back on the top of the
cabinet will restrict airflow into the cold aisle. Placing the module too far toward the front of the
cabinet will decrease the amount of hot air drawn into the module.
Figure 19
Positioning Liebert XDV on top of cabinet
Liebert XDV is suspended from
ceiling structure...
X
X
....the separation
between the rack and
the Liebert XDV
should be held to less
than 1" (25mm). If this
is not possible, an air
blocker should be
added to prevent
unwanted airflow
between the hot aisle
and the cold aisle.
CORRECT
Liebert XDV is flush with
front edge of rack
INCORRECT
Liebert XDV is
too far from front
edge of rack
INCORRECT
Liebert XDV
hangs over front
edge of rack
Both of the Liebert XDV’s power cords should be connected to power sources. If only one power source
is available, then only the power cord labeled “SECONDARY” should be connected to the power
source.
Piping for the Liebert XDV is routed upward to the main return and supply pipes to and from the
Liebert XDP/Liebert XDC.
Table 7, below, may be used to determine the correct number of Liebert XDV modules.
Table 7
Determine required number of Liebert XDV modules (example below is Liebert XDV10)
Input Information
Step
Total heat load in the room, kW
A
Reserve capacity needed
(10% - 25% of A is recommended)
B
C
Existing/planned Liebert
Deluxe/DS sensible capacity, kW
Room area, square feet
Results
Required cooling capacity, kW = A + B
D
E
Required Liebert XD system cooling capacity, kW = C – D
F
Number of Liebert XDV10 modules required = E ÷ 10, rounded up (60Hz)
= E ÷ 8, rounded up (50Hz)
G
Number of Liebert XDP/Liebert XDC units required = F ÷ 16,
rounded up (60Hz and 50Hz)
H
I
Area served by each Liebert XDV10 = H ÷ F
L
Required Liebert XD system cooling density = E x 1000 ÷ H
OK if under 580 for 12-foot cold aisle spacing
OK if under 435 for 16-foot cold aisle spacing
Otherwise, additional Liebert Deluxe or Liebert DS capacity is needed.
23
Designing a Liebert XD Solution
3.11
Liebert XDP/Liebert XDC Placement
The Liebert XDP/Liebert XDC may be placed in the critical space or in an adjacent equipment room.
The allowable distance between the Liebert XDP/Liebert XDC and its connected cooling modules is
determined by the piping design and by the amount of refrigerant required. Refer to 3.22 - Liebert XD
Refrigerant and 3.13 - Liebert XD Piping System Design.
The maximum height of any of the main or connecting piping should be no more than 20 feet (6m)
above the top of the Liebert XDP/Liebert XDC unit. Liebert XDV/Liebert XDO modules should be
placed as close to the same level as possible. The differences in elevation between the highest and
lowest Liebert XDV or Liebert XDO module in a system should be no more than 6 feet (2m).
3.12
Examples of Expansion and Interlaced Connection of Liebert XD Cooling Modules
Figure 20
Liebert XDV modules mounted on racks emitting 3kW of heat, top view
Downflow
Cooling
Unit
Downflow
Cooling
Unit
XDVs Mounted
on Equipment Racks
Equipment Racks
without XDVs
Circuit 1
24
Perforated
Raised
Floor Tiles
Designing a Liebert XD Solution
Figure 21
Liebert XDV modules mounted on racks emitting 5kW of heat, top view
Downflow
Cooling
Unit
Downflow
Cooling
Unit
XDVs Mounted
on Equipment Racks
Interlaced piping arrangement
for enhanced protection
Figure 22
Circuit 1
Circuit 2
Equipment Racks
without XDVs
Perforated
Raised
Floor Tiles
Liebert XDV modules mounted on racks emitting 8kW of heat top view
Downflow
Cooling
Unit
Downflow
Cooling
Unit
XDVs Mounted
on Equipment Racks
Interlaced piping arrangement
for enhanced protection
Circuit 1
Circuit 2
Perforated
Raised
Floor Tiles
25
Circuit 3
Designing a Liebert XD Solution
Figure 23
Liebert XDV modules mounted on racks emitting 16kW of heat top view
Downflow
Cooling
Unit
Downflow
Cooling
Unit
XDVs Mounted
on Equipment Racks
Interlaced piping
arrangement
XDOs Mounted
for enhanced
on Equipment Racks
protection
Figure 24
Circuit 1
Circuit 2
Circuit 3
Circuit 4
Circuit 5
Circuit 6
Multiple Liebert XD modules in an interlaced system
26
Perforated
Raised
Floor Tiles
Designing a Liebert XD Solution
Installing the Liebert XDR in a hot aisle/cold aisle configuration provides benefits such as increased
ride-through in the event of a failure. With the room-neutral cooling, the Liebert XDR can be used
where hot aisle/cold aisle setup is not feasible to address hot spots (see Figure 25).
Figure 25
Liebert XD modules not in hot aisle/cold aisle configuration
These methods can increase the redundancy of any Liebert XD system:
•
•
•
•
3.13
Hot aisle/cold aisle design
Interlacing the modules with different Liebert XDPs or Liebert XDCs
Using multiple types of Liebert XD cooling modules
Containment methods
Liebert XD Piping System Design
All piping must be ASTM (American Society for Testing and Materials) Type “ACR” copper pipe. The
typical maximum operating pressure in the system is 90 psi (620kPa).
Piping for the Liebert XD system is arranged in a manner similar to piping for a chilled water system.
Liebert XD cooling modules are connected in parallel between the main return and supply pipes going
to and from the Liebert XDP/Liebert XDC. Figure 26 represents a typical configuration. The
guidelines provided for pipe size must be strictly followed. Failure to size the main lines
and connection lines adequately may result in reduced cooling capacity. The critical aspects
of pipe sizing are related to refrigerant volume and pressure drop. Each must be minimized.
Figure 26
20ft.
(6.7m)
max.
Piping for Liebert XDP/Liebert XDC used with Liebert XD cooling modules
All supply and
return mains must
be level with or
above the top of all
Liebert XDP or
Liebert XDC units
9ft.
(2.7m)
max.
Liebert XD Cooling
Modules
Liebert XDP/
Liebert XDC
SLOPE—The main supply and return lines to and from the Liebert XDP/Liebert XDC
must be sloped downward toward the Liebert XDP/Liebert XDC at a rate of 1-2" per
20 feet (25.4-51mm per 6m) of pipe run. Horizontal connector lines should also be
sloped downward from the cooling modules toward the main supply and return lines.
27
Designing a Liebert XD Solution
The assembly and connection means used for piping in the Liebert XD system are similar to that of
conventional refrigeration systems. All piping should be installed with high temperature brazed
joints. Soft solder is not recommended. The lines being brazed MUST be filled with flowing dry
nitrogen during brazing to prevent excessive oxidation and scale formation inside the piping.
Prevailing good refrigeration practices must be employed for piping supports, leak testing,
dehydration and charging. Failure to use good system practices may result in damage to the system.
Refer to the ASHRAE refrigeration handbook for general good-practice refrigeration piping.
Follow all guidelines in 3.13 - Liebert XD Piping System Design and 3.14 - Liebert XD Piping
Slope during installation.
Insulate all piping lines to prevent condensation in applications where the dew point approaches the
R-134a refrigerant temperature. This might occur where Liebert XD module piping is above a
dropped ceiling or in other areas not measured by sensors connected to the Liebert XDP or Liebert
XDC.
See Table 8 for recommended pipe sizes and Figure 27 for piping segment locations.
Table 8
Supply, return pipe sizes for refrigerant loop
Pipe Function
Key to Piping
in Figure 27
Liebert XDP supply line, from Liebert XDP supply
to farthest Liebert XD cooling module
a
Liebert XDP return line, from farthest Liebert XD
cooling module to Liebert XDP return
B
From any model Liebert XDO/Liebert XDH/Liebert
XDR supply to supply line of Liebert XDP
C
From any model Liebert XDO/Liebert XDH/Liebert
XDR return to return line of Liebert XDP
D
From any model Liebert XDV/Liebert XDCF
supply to supply line of Liebert XDP
C
From any model Liebert XDV/Liebert XDCF return
to return line of Liebert XDP
D
Size / Equivalent Pipe Length
1-1/8" OD for lengths up to 60 feet
1-3/8" OD for lengths over 60 but less than 175 feet
2-1/8" OD for lengths up to 60 feet
2-5/8" OD for lengths over 60 but less than 175 feet
1/2" OD for lengths up to 10 feet
7/8" OD for lengths over 10 but less than 25 feet
7/8" OD for lengths up to 10 feet
1-1/8" OD for lengths over 10 but less than 25 feet
1/2" OD for lengths up to 10 feet
5/8" OD for lengths over 10 but less than 35 feet
5/8" OD for lengths up to 10 feet
7/8" OD for lengths over 10 but less than 35 feet
For additional information about piping connections, see the unit’s user manual: Liebert XDP, 16644;
Liebert XDC, SL-16671; Liebert XDO, SL-16666; Liebert XDV, SL-16626; Liebert XDCF, SL-16678;
Liebert XDR SL-16935; and Liebert XDH SL-17210.
NOTE
To minimize the amount of refrigerant required, do NOT oversize the piping.
Figure 27
Generic piping layout
To Chiller,
Condenser
or Drycooler
To Chiller,
Condenser
or Drycooler
Liebert XDC
or
Liebert XDP
Liebert XDC
or
Liebert XDP
A
B
Pumped
Refrigerant
R134 a
A
B
Pumped
Refrigerant
R134 a
28
C
D
C
D
C
D
C
D
Liebert XD
Cooling Module *
Liebert XD
Cooling Module *
Liebert XD
Cooling Module *
Liebert XD
Cooling Module *
Supply
Lines
Return
Lines
* Liebert XDCF,
Liebert XDH,
Liebert XDO,
Liebert XDR
or Liebert XDV
Designing a Liebert XD Solution
3.14
Liebert XD Piping Slope
The main supply and return lines to and from the XDP/XDC must be sloped downward toward the
XDP/XDC at a rate of 1-2" per 20 feet (25-51mm per 6m) of pipe run. Horizontal connector lines
should also be sloped downward from the cooling modules toward the main supply and return lines.
3.15
Bypass Flow Controllers
To ensure the Liebert XDP/XDC pumps operate within the optimum range, some installations require
one or more bypass flow controller(s). These devices are added to the field piping, and simulate the
flow of additional cooling modules.
Each bypass flow controller should be installed with one shutoff valve to allow the controller to be
disabled when cooling modules are added to a Liebert XD system.
If bypass flow controllers are required, they should be connected between the main supply and the
main return lines of the field piping. The connection points to the main supply and return lines should
be in a convenient and accessible location between the Liebert XDP/Liebert XDC and the first Liebert
XD module in the circuit. See Figures 29 and 28 for piping details of the bypass flow controller.
Refer to Table 9 to determine the number of bypass flow controllers needed, based on the total
nominal cooling capacity of the cooling modules in each Liebert XD system.
Table 9
Bypass flow controllers for Liebert XDC- or Liebert XDP-based systems
Cooling Modules Cumulative Model Size
Figure 28
Required Number of Bypass Flow Controllers
Liebert XDP
Liebert XDC
48 to 63
3
N/A
64 to 95
2
2
96 to 127
1
1
128 to 160
0
0
Bypass flow controller details, dimensions
4"
(102mm)
7/8"
(2.2mm) ID
Figure 29
Bypass flow controller arrangement
7/8" Refrigerant Grade
Full Port Ball Valve
Field-Supplied and Field-Installed
Flow Direction
Bypass Flow Controller
(Field-Installed)
Supply
Main
29
Return
Main
Designing a Liebert XD Solution
Figure 30
Bypass flow controller piping
Liebert XD
Cooling
Module #1
Liebert XD
Cooling
Module #2
Bypass Flow
Controllers
Coolant
Supply
Coolant
Return
Filter Dryer
Assembly
Liebert XDP
or
Liebert XDC
30
Designing a Liebert XD Solution
3.16
Piping Details—Shutoff/Isolation Valves
Isolation valves must be installed on the Liebert XDC’s refrigerant circuit to permit maintenance on
the unit (see Figure 31).
Figure 31
General piping details
Return
Supply
Field-Supplied
Full-Port Ball Valves
Factory-Supplied
Full-Port Ball Valves
On Liquid Refrigerant
Lines
Field Piping, Supplied and Piped By Field
3.17
Field-Supplied Full-Port
Ball Valves on Hot Gas
Refrigerant Lines
Piping Details—Shutoff/Isolation Valves
Isolation valves must be installed on the Liebert XDP’s refrigerant circuit to permit maintenance on
the unit (see Figure 32).
Figure 32 General piping details
Return
Supply
Return
Emerson recommends
field-installation of shutoff
valves at these points to
permit isolating the
Liebert XDP for
maintenance.
Supply
Liebert
XDP A
Liebert
XDP B
Floor
Isolation
valves
Isolation
valves
Building Chilled Water Supply
Building Chilled Water Return
31
Designing a Liebert XD Solution
Figure 33
Hard-pipe connection diagram for Liebert cooling modules
Refer to Table 8
Return Main
for details.
(seen from end )
2-1/8" O.D.
or 2-5/8" O.D.
Recommended Arc
Acceptable Arc
Supply Main
(seen from end )
1-1/8" O.D.
or 1-3/8" O.D.
Refrigerant -Grade
Full-Port Ball Valve
Field-Supplied and
Field-Installed to Match
Pipe Size
Refrigerant -Grade
Full-Port Ball Valve
Field-Supplied and
Field- Installed to Match
Pipe Size
Maximum
9ft. (2.75m)
actual height
Copper Tubing
Total length of each line from
Liebert XD Cooling Module
(Liebert XDH , Liebert XDO ,
Liebert XDR , Liebert XDV ) to
Main
Supply
to Cooling
Module
Return from Liebert XD
Cooling Module
Top of Liebert XD
Cooling Module
Rear of
Liebert XD
Cooling
Module
32
Designing a Liebert XD Solution
3.18
Piping Details—Return Header Port Orientation
The return header port from a Liebert XD cooling module is a gravity return and must be properly
oriented to the refrigerant return header for proper flow. The return header contains R134a
refrigerant in gas and liquid form. Improperly connecting a cooling module’s return header port to the
return header could permit liquid refrigerant to back up into the cooling module. See Figure 34 for
proper orientation.
Supply header ports can be oriented at any angle to the header because supply headers carry only
liquid R134a refrigerant and are not gravity operated.
Figure 34
Liebert XD return header orientation
Port Kit, Return Header Port
Connection to a Liebert XD
Flex Hose, or a hard piped
connection from a cooling
module to the return header.
t
p
able
e
c
c
A
R134a Refrigerant
GAS
R134a Refrigerant
LIQUID
No
t Ac
le
b
cepta
33
Designing a Liebert XD Solution
Figure 35
Liebert XD supply header orientation
Port Kit, Supply Header Port
Connection to a supply header.
Any connection angle
is functional.
t
p
a
e
ble
c
c
A
R134a Refrigerant
LIQUID
A c c e p t a ble
3.19
Piping Details—Bull Heading Layout
Good piping layout employs offsetting connections to promote easier refrigerant flow, as shown in
Figure 36. “Bull head T” connections should be avoided.
Figure 36
Efficient piping layout—avoid “bull head T” connections
Avoid this pipe
layout, known as
a “bull head tee.”
Refrigerant Flow
This pipe layout with
offset pipes keeps
flow moving.
Refrigerant Flow
Refrigerant Flow
Refrigerant Flow
INCORRECT CONNECTION
BULL HEAD T
CORRECT CONNECTION
OFFSET PIPES
34
Designing a Liebert XD Solution
3.20
Piping Installation Method Prefabricated Headers
The assembly and connection means used for piping in the Liebert XD system are similar to those
used for conventional refrigeration systems. All piping should be installed with high-temperature
brazed joints. Soft solder is not recommended. During brazing, the lines must be filled with flowing
dry nitrogen to prevent excessive oxidation and scale formation inside the piping. Prevailing good
refrigeration practices must be employed for piping supports, leak testing, dehydration and charging.
Failure to use good system practices may result in damage to the system. Refer to the ASHRAE
refrigeration handbook for general good-practice refrigeration piping.
Follow all guidelines in 3.13 - Liebert XD Piping System Design and 3.14 - Liebert XD Piping
Slope during installation.
Figure 37
Two-port prefabricated piping for Liebert XD cooling modules
H
ODS
L
ODR
96" Nominal
(2438mm)
48"
(1219mm) Ref. Typ.
Ref.
24"
Typ.
(610mm)
Supply
8-5/16" Ref. Typ.
(211mm)
Return
Table 10
Supply
inch (mm)
Return
inch (mm)
DPN000773
Two-port prefabricated piping legend
Branch Piping
Standard Run
Long Run *
Two Port
185797G21
185800G21
1-1/8
1-3/8
Height (H)
8-3/4 (222)
8-3/4 (222)
Length (L)
6-3/4 (171)
6-7/8 (175)
2-1/8
2-5/8
Height (H)
10-1/2 (267)
10-1/2 (267)
Length (L)
8-3/4 (222)
9-1/8 (232)
Outside Diameter (ODS)
Outside Diameter (ODR)
* Pipe runs greater than 60 equivalent feet
35
Designing a Liebert XD Solution
Figure 38
Four-port prefabricated piping for Liebert XD cooling modules
H
ODS
L
ODR
28-9/16"
Ref.
(725mm)
96" Nominal
(2438mm)
48" Ref. Typ.
(1219mm)
19-7/16"
Ref.
(494mm)
Supply
Return
19-7/16" Ref.
(494mm)
Table 11
Supply
inch (mm)
Return
inch (mm)
28-9/16" Ref.
(725mm)
Four-port prefabricated piping legend
Branch Piping
Standard Run
Long Run *
Four Port
186551G21
186552G21
Outside Diameter (ODS)
1-1/8
1-3/8
Height (H)
8-3/4 (222)
8-3/4 (222)
Length (L)
6-3/4 (171)
6-7/8 (175)
2-1/8
2-5/8
Height (H)
10-1/2 (267)
10-1/2 (267)
Length (L)
8-3/4 (222)
9-1/8 (232)
Outside Diameter (ODR)
* Pipe runs greater than 60 equivalent feet
36
DPN000773
Designing a Liebert XD Solution
Figure 39
Five-port prefabricated piping for Liebert XD cooling modules
H
L
ODS
ODR
120" Nominal
(3048mm)
24"
(610mm)
Ref. Typ.
Supply
4-5/8"
(117mm)
8-5/16"
(211mm) Ref. Typ.
Return
Table 12
Supply
inch (mm)
Return
inch (mm)
DPN000773
Five-port prefabricated piping legend
Branch Piping
Standard Run
Long Run *
Five Port
185797G51
185800G51
Outside Diameter (ODS)
1-1/8
1-3/8
Height (H)
8-3/4 (222)
8-1/2 (216)
Length (L)
6-3/4 (171)
7 (178)
2-1/8
2-5/8
Height (H)
10-1/2 (267)
10-1/2 (267)
Length (L)
8-3/4 (222)
9-1/8 (232)
Outside Diameter (ODR)
* Pipe runs greater than 60 equivalent feet
37
Designing a Liebert XD Solution
Figure 40
Ten-port prefabricated piping for Liebert XD cooling modules
H
ODS
ODR
L
120" Ref.
(3048mm)
7-7/16" Ref. Typ.
(189mm)
9-1/16"
(230mm) Ref. Typ.
Table 13
Supply
inch (mm)
Return
inch (mm)
7-7/16"
(189mm)
24"
(610mm)
Ref. Typ.
Supply
Return
DPN000773
Ten-port prefabricated piping legend
Branch Piping
Standard Run
Long Run *
Ten Port
186650G51
186553G51
1-1/8
1-3/8
Height (H)
8-3/4 (222)
8-3/4 (222)
Length (L)
6-3/4 (171)
6-7/8 (175)
2-1/8
2-5/8
Height (H)
10-1/2 (267)
10-1/2 (267)
Length (L)
8-3/4 (222)
9-1/8 (232)
Outside Diameter (ODS)
Outside Diameter (ODR)
* Pipe runs greater than 60 equivalent feet
38
16-9/16"
(421mm)
Ref. Typ.
Designing a Liebert XD Solution
3.21
Liebert XD Flex Pipe Kit
Liebert XD Flex Pipe kits are available in lengths of 4, 6, 8 and 10 feet (1.2, 1.8,2.4 and 3 meters).
Connection style to the module end may be straight or 90 degrees with one-shot or removable
connections. Connection to the prefabricated piping assembly is a threaded coupler. For data on
acquiring the correct kit for your installation, see Table 14.
Table 14
Liebert XD Flex Pipe assemblies, supply and return
Liebert XDV
Description
Liebert
XDCF
Liebert
XDO
One-Shot Removable One-Shot
Couplings Couplings Couplings
One-Shot
Couplings
Liebert XDH
One-Shot
Couplings
Removable
Couplings
Liebert XDR
One-Shot Removable
Couplings Couplings
4ft long (1.2m), 0º
186568G4
187867G4
186568G4 2
186566G4
2 x 186566G4 2 x 187865G4
186566G4
187865G4
4ft long (1.2m),
90º
186567G4
187866G4
—
186565G4
2 x 186565G4 2 x 187864G4
186565G4
187864G4
6ft long (1.8m), 0º
186568G1
187867G1
186568G1 2
186566G1
2 x 186566G1 2 x 187865G1
186566G1
187865G1
6ft long (1.8m),
90º
186567G1
187866G1
—
186565G1
2 x 186565G1 2 x 187864G1
186565G1
187864G1
8ft long (2.5m), 0º
186568G3
187867G3
186568G3 3
186566G3
2 x 186566G3 2 x 187865G3
186566G3
187865G3
8ft long (2.5m),
90º
186567G3
187866G3
—
186565G3
2 x 186565G3 2 x 187864G3
186565G3
187864G3
10ft long (10m),
0º
186568G2
187867G2
186568G2 3
186566G2
2 x 186566G2 2 x 187865G2
186566G2
187865G2
10ft long (10m),
90º
186567G2
187866G2
—
186565G2
2 x 186565G2 2 x 187864G2
186565G2
187864G2
Min Bend Radius,
7" (178mm) 7" (178mm) 7" (178mm) 7" (178mm)
Supply 1
Min Bend Radius,
Return 1
8" (203mm)
7" (178mm)
7" (178mm)
7" (178mm) 7" (178mm)
9" (229mm)
1. The minimum bend radius is for the flexible portion of the Liebert XD Flex Pipe. Because a section of hard pipe is at each end of the
Liebert XD Flex Pipe, the minimum bend radius can be larger.
2. Top Module
3. Bottom Module
3.22
Liebert XD Refrigerant
The refrigerant used in the Liebert XD system is HFC-134a (1,1,1,2-tetrafluoroethane), made by a
number of manufacturers. The amount of refrigerant used by the Liebert XD system may be
significantly higher than in typical DX cooling systems.
NOTICE
Risk of improper oil use. Can cause equipment damage.
The Liebert XD pumped R-134a refrigerant circuits do not use refrigerant oil. Do NOT put oil
in the R-134a system.
All the major components of a Liebert XD system must be installed in a space with a volume of at
least 1,000 ft3 (28.3m3) for each 13 pounds of refrigerant in that system from ANSI/ASHRAE
Standard 34-2007, Designation and Safety Classification of Refrigerant If the Liebert XDP/Liebert
XDC is placed in a separate area, such as a machine room, then this area must also meet the volume
requirement. Inside the critical space, this includes the space under the raised floor, and the space
between the top of the raised floor and the bottom of a suspended ceiling. If the suspended ceiling is
all open grates, then this additional space, up to the overhead deck, would also be included.
39
Designing a Liebert XD Solution
Example
A space is 5,000 square feet, with an 18" raised floor and an 8' 6" suspended ceiling. Liebert XDOs
and a Liebert XDP are to be placed in this raised-floor area.
The volume of the space is (1.5 + 8.5) x 5,000 or 50,000 cubic feet.
The maximum amount of R-134a refrigerant that can be used in a single Liebert XDP/Liebert
XDC/Liebert XD module system within this space is 13 * (50000/1000) = 13 * 50 = 650 lb.
Multiple Liebert XD systems can be installed in this space, as long as the amount of R-134a
refrigerant in any one system does not exceed 650lb. (294.8kg).The maximum amount of
refrigerant is 650lb (294.8kg) per Liebert XD loop.
NOTE
Local codes might permit exceeding the maximum refrigerant limit above if a refrigerant
detector and an exhaust system are installed. Installing oxygen sensors may meet some local
codes.
3.23
Determining Refrigerant Volume
After the preliminary system design is completed, Tables 15 through 20 may be used to determine
the amount of refrigerant required. Perform the calculation below for each Liebert XD system being
configured.
NOTE
All lengths in Tables 15, 16, 17 and 18, are actual pipe lengths, not equivalent pipe lengths.
3.23.1 Liebert XDP/Liebert XDC Pumped R-134a Circuit Volume
This is the refrigerant circuit from the Liebert XDP/Liebert to the Liebert XD cooling module.
NOTE
System refrigerant volume calculations in Tables 15, 16, 17 and 18, are based on a fully
loaded system. Additional charge may be required for lightly loaded systems.
Table 15
System R-134a charge for a Liebert XDP/Liebert XDC with any model
Liebert XDH/Liebert XDO/Liebert XDV/Liebert XDCF
Refrigerant Charge,
lb (kg)
Per Liebert XD Unit
(Excludes Connector Lines to and from Liebert XD Cooling Module)
157 (71.2)
Liebert XDP/Liebert XDC
3.55 (1.61)
Liebert XDO
2.32 (1.05)
Liebert XDV
2.66 (1.21)
Liebert XDH (per circuit)
1.41 (0.64)
Liebert XDCF
4 (1.81)
Table 16
Liebert XDR
System refrigerant charge for the supply and return mains
Refrigerant Charge,
lb/foot (kg/m)
Supply/Return Main Length and Diameter
0.45 (0.67)
Main supply actual length per 1-1/8" OD copper tubing
0.68 (1.01)
Main supply actual length per 1-3/8" OD copper tubing
0.28 (0.42)
Main return actual length per 2-1/8" OD copper tubing
0.43 (0.64)
Main return actual length per 2-5/8" OD copper tubing
40
Designing a Liebert XD Solution
Table 17
R-134a refrigerant charge for hard-piped connector lines to and from any model
Liebert XDH/Liebert XDO/Liebert XDV
Refrigerant Charge,
lb/foot (kg/m)
Hard-Piped Connector Length and Diameter
0.08 (0.12)
1/2" OD Liebert XDH/Liebert XDO/Liebert XDR/Liebert XDV supply connector actual length
0.13 (0.19)
5/8" OD copper tubing Liebert XDV supply connector actual length
0.26 (0.39)
7/8" OD Liebert XDO/Liebert XDH/Liebert XDR supply connector actual length
0.02 (0.03)
5/8" OD copper tubing Liebert XDV return connector actual length
0.04 (0.06)
7/8" OD copper tubing Liebert XDV return connector actual length
0.04 (0.06)
7/8" OD copper tubing Liebert XDH/Liebert XDO/Liebert XDR return connector actual length
0.07 (0.1)
1-1/8" OD copper tubing Liebert XDH/Liebert XDO/Liebert XDR return connector actual
length
Table 18
R-134a refrigerant charge for Flex Pipe connector lines to and from any model
Liebert XDO/Liebert XDH/Liebert XDV/Liebert XDCF
Refrigerant Charge, lb. (kg)
Supply Line Diameter 1/2"
0.3 lb. (0.14)
0.5 lb. (0.23)
0.7 lb. (0.32)
0.8 lb. (0.36)
Return Line Diameter 5/8"
0.01 lb. (0.01)
0.02 lb. (0.01)
0.03 lb. (0.01)
0.03 lb. (0.01)
Return Line Diameter 1"
0.13 lb. (0.06)
0.2 lb. (0.09)
0.27 lb. (0.12)
0.33 lb. (0.15)
Metal Flex Pipe Connector Length
4 ft. Flex Pipe All Liebert XD Cooling Module
6 ft. Flex Pipe All Liebert XD Cooling Module
8 ft. Flex Pipe All Liebert XD Cooling Module
10 ft. Flex Pipe All Liebert XD Cooling Module
4 ft. Flex Pipe existing Liebert XDCF/Liebert XDV systems
6 ft. Flex Pipe existing Liebert XDCF/Liebert XDV systems
8 ft. Flex Pipe existing Liebert XDCF/Liebert XDV systems
10 ft. Flex Pipe existing Liebert XDCF/Liebert XDV systems
4 ft Flex Pipe Liebert XDH/Liebert XDO/Liebert XDR supply
6 ft Flex Pipe Liebert XDH/Liebert XDO/Liebert XDR supply
8 ft Flex Pipe Liebert XDH/Liebert XDO/Liebert XDR supply
10 ft Flex Pipe Liebert XDH/Liebert XDO/Liebert XDR supply
3.23.2 Calculating Refrigerant R134a Charge—Example
Using Tables 15, 16, 17 and 18, calculate the refrigerant charge of the individual sections of your
Liebert XD system. Add the calculated charge amounts to determine the amount of R-134a
refrigerant required for one system combining a Liebert XDP with Liebert XD cooling modules
(Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV). The example below
combines one Liebert XDP with 20 Liebert XDV8 cooling modules.
Table 19
Calculating refrigerant charge—example
Components
Liebert XDP/Liebert XDC
Number of Units
or Piping Length, feet
Pounds Per Component
1
157
157
Total, lb.
Liebert XDV8 Cooling Modules
20
2.32
46.4
Supply Main, 1-1/8"
100
0.45
45
Return Main, 2-1/8"
100
0.28
28
Liebert XDV 1/2" supply Liebert
XD Flex Pipes
20
0.8
16
Liebert XDV 5/8" return Liebert
XD Flex Pipes
20
0.03
0.6
Total
41
293
Designing a Liebert XD Solution
Table 20
Worksheet to calculate refrigerant charge
Components
Number of Units
or Piping Length
Pounds Per Component
Total
Total
Verify that the refrigerant volume of the Liebert XD system with the longest piping length is within
the allowable limit. If the allowable limit is exceeded, the Liebert XDP/Liebert XDC should be moved
closer to the cooling modules (refer to 3.22 - Liebert XD Refrigerant for limits and related details).
Another way to shorten the total pipe length is to reroute the pipe runs.
3.24
Chilled Water Piping
The Liebert XDP is offered only with a two-way chilled water control valve. Some applications may
require the use of a pressure activated bypass valve to prevent dead-heading of the chilled water
pump. This bypass valve must be specified by the engineer responsible for design of the chilled water
field piping system.
NOTICE
Risk of particles in chilled water. Can cause equipment damage and reduced cooling.
Failure to install a strainer in the supply line to the Liebert XDP can result in damage to the
unit’s heat exchanger.
Install a 20-40 mesh strainer on the chilled water supply to the Liebert XDP. The strainer is required
to prevent particles in the chilled water from entering the heat exchanger of the Liebert XDP. The
maximum distance of the strainer from the Liebert XDP is 10 feet (3m).
42
Designing a Liebert XD Solution
Figure 41
Piping access points
To first cooling module
or bypass flow controller **
To first cooling
module or bypass
flow controller **
Install replaceable
filter dryer assembly
in liquid supply line B.
Close this
valve during
normal
operation
Orientation
determined
by installer *
* Orientation
determined
by installer.
A - Return from Liebert XD
cooling modules
Orientation
determined
by installer *
B - Supply to Liebert XD Cooling Modules
17-1/4"
(438mm)
Emerson recommends field-installation
of shutoff valves at these points to permit
isolating the Liebert XDP for maintenance
16-1/8"
(409.6mm)
10" (254mm)
19"
(483mm)
Dimensions are
approximate
and subject to change
without notice.
* Allow 8" (204mm) clearance for filter replacement.
** To ensure ensure all refrigerant flow is filtered,
install the filter dryer assembly between the discharge
line of the Liebert XDP and the first bypass
flow controller or the first Liebert XD cooling module.
*** For each Liebert XDP unit, a separate
20-40 mesh strainer is REQUIRED in the
chilled water supply from the chilled water
source. The strainer is field-supplied and
field-installed. The maximum distance
of the strainer is 10 feet (3m) from the
Liebert XDP.
D - Chilled Water Return
To Chilled Water Source
C - Chilled Water Supply
From Chilled Water Source
DPN001598
Pg. 3, Rev. 7
Strainer ***
Table 21
Unit piping outlet connection sizes, inches, OD Cu
Model
Pipe Connection Point
50/60 Hz
A
B
C
D
XDP160
2-1/8
1-1/8
2-5/8
2-5/8
Chilled water connections to the Liebert XDP are near the bottom of the unit. Refer to the Liebert
XDP user manual (SL-16644) for further information. Piping is routed downward from the unit to
chilled water piping under the raised floor. Connections are made using standard practices for copper
chilled water piping. Field-supplied Victaulic® connections may be used to simplify installation in
existing facilities. Refer to Table 75 for additional information.
43
Designing a Liebert XD Solution
3.25
Electrical
Make all wiring and electrical connections in accordance with local and national codes. Refer to the
applicable table in 9.0 - Specifications and Model Number Nomenclature regarding wire size
and circuit protection requirements. Refer to electrical schematic when making connections.
3.26
Temperature/Humidity Sensor Locations
The display panel sensor and Liebert iCOM sensor (shipped loose) must always be installed in the
conditioned space. The display panel sensor and Liebert iCOM sensor may be mounted on the Liebert
XDC/XDP’s front door if the unit is located in the area that it conditions.
The remote temperature / humidity sensor for the Liebert XDP and the Liebert XDC should be
installed in the higher-temperature portion of the cold aisle where the Liebert XD modules are
located. Alternatively, it can be placed on the return air side of the primary air mover, such as a
Liebert DS, in the room if it represents the conditions where all the Liebert XD cooling modules are
located. It should not be installed where ambient air might cause false readings, for example, near
unsealed doors, windows and similar areas.
44
Designing a Liebert XD Solution
3.27
Connecting Liebert XDP and Liebert XD Cooling Modules in a CANbus Network
A Controller Area Network (CAN) is a specialized internal communication network. It allows the
Liebert XDP and the Liebert XD smart modules to communicate without a host computer.
Networking a Liebert XDP with smart modules enables the smart modules to be controlled and
monitored from the Liebert XDP.
The Liebert XD smart modules CANbus is to be networked only to the Liebert XDP that is supplying
coolant to the smart modules.
Figure 42
Liebert XD system with CANbus
Remote
Sensor A
Remote Sensor B
3.27.1 CANbus Cables
The Liebert XDP may be connected to smart modules with CANbus cables. The shielded cable
consists of three pairs of twisted wires with a six-pin RJ-12 connector.
Figure 43
CANbus cable wiring
Grounding
Wire
1
2
3
4
5
6
Black
Brown
Blue
Violet
Yellow
Green
Table 22
1
2
3
4
5
6
Grounding
Wire
Pair 1
Pair 2
Pair 3
CANbus cable part numbers
Length ft (m)
Part #
3 (0.9)
300157G10
6 (1.8)
300157G1
10 (3.0)
300157G2
15 (4.6)
300157G11
20 (6.1)
300157G3
30 (9.1)
300157G4
60 (18.3)
300157G5
90 (27.4)
300157G8
120 (36.6)
300157G7
150 (45.7)
300157G8
45
Designing a Liebert XD Solution
Plan wiring runs for U2U communication when designing the layout of the conditioned space. In
addition to following general good wiring practices, take these precautions:
• Keep control and communication cables away from power cables to prevent electromagnetic
interference.
• Do not bend cables to less than four times the diameter of the cable.
• Do not deform cables when securing them in bundles or when hanging them.
• Keep cables away from devices that can introduce noise into them, such as machines, fluorescent
lights and electronics.
• Avoid stretching cables; tension when pulling cables should not exceed 25 pounds (11kg) of
pulling tension.
• Do not secure cables with any method that might damage them. Use approved hangers, such as
those for telephone wire or RG-6 coaxial cable, available at most hardware stores.
3.27.2 CANbus Cable Length in a Network
The maximum total length of cable that can be used in a CANbus network differs by the type of
Liebert XD cooling module as shown in Table 23.
Table 23
Allowable total CAN cable length
Allowable Total CAN
Cable Length, ft (m)
Module
Liebert XDV8
580 (177)
Liebert XDV10
580 (177)
Liebert XDO16
590 (180)
Liebert XDO20
590 (180)
Liebert XDH20
580 (177)
Liebert XDH32
585 (178)
*
Figure 44
Liebert
XDP
The internal CANbus cable within the Liebert XD module and the remote sensors has been accounted for.
Single daisy chain of Liebert XDO smart modules in CANbus network
Remote
Sensor A
Rack
Rack
Liebert
XDO
Liebert
XDO
Rack
Rack
Table 24
Rack
Rack
Rack
Rack
Liebert
XDO
Liebert
XDO
Rack
Rack
Rack
Rack
Rack
Rack
Liebert
XDO
Liebert
XDO
Rack
Rack
Rack
Rack
Rack
Rack
Liebert
XDO
Liebert
XDO
Rack
Rack
Remote
Sensor B
Cumulative cable length in Figure 44
Cable
Segments
Length of Each
ft. (m)
14
6 (1.8)
84 (25.6)
1
20 (6)
20
(6)
1
30 (9.1)
30
(9.1)
134
(40.8)
Combined cable length
Cumulative Length
ft. (m)
The cumulative length of cable used in the example in Figure 44 is 134 ft. (40.8m), far shorter than
the maximum allowable cable run of 580 ft. (177m) for Liebert XDV10 modules.
46
Designing a Liebert XD Solution
3.27.3 Remote Sensor Placement Within the CANbus
Two remote sensors are shipped with the Liebert XDP. One shielded CANbus cable is provided with
each sensor. Sensor A is to be connected to the directly the Liebert XDP. Sensor B is to be connected to
the CANbus within the smart module chain. This can be at the end of the chain as shown in
Figure 45. For proper placement within the room, see 3.26 - Temperature/Humidity Sensor
Locations.
Figure 45
Liebert
XDP
Sensor at the end of daisy chain of Liebert XDO smart modules in CANbus network
Remote
Sensor A
Rack
Rack
Liebert
XDO
Liebert
XDO
Rack
Rack
Rack
Rack
Rack
Liebert
XDO
Liebert
XDO
Rack
Rack
Rack
Rack
Rack
Rack
Rack
Liebert
XDO
Liebert
XDO
Rack
Rack
Rack
Rack
Rack
Liebert
XDO
Liebert
XDO
Rack
Rack
Rack
Remote
Sensor B
Sensor B can be placed in the middle of the daisy chain as shown in Figure 46; however, the
additional cable length must be subtracted from the allowable length.
Figure 46
Sensor within the daisy chain of Liebert XDV smart modules in CANbus network
Liebert
XDV
Liebert
XDP
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Remote
Sensor A
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Remote
Sensor B
The modules can also be split into two chains as shown in Figure 47.
Figure 47
Dual daisy chain of Liebert XDV smart modules in CANbus network
Liebert
XDV
Liebert
XDP
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Remote
Sensor A
Remote
Sensor B
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
47
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Designing a Liebert XD Solution
The sensors can also be isolated in an independent daisy chain, see Figure 48.
Figure 48
Independent smart module and sensor daisy chains in CANbus network
Liebert
XDV
Liebert
XDP
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Remote
Sensor B
Remote
Sensor A
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
48
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
4.0
LIEBERT XD COOLING MODULES—LIEBERT XDCF, LIEBERT XDH,
LIEBERT XDO, LIEBERT XDR AND LIEBERT XDV
4.1
Liebert XDCF Standard Features
The Liebert XDCF is a self-contained module designed to cool Egenera’s BladeFrame EX cabinets and
equipment without exhausting heat into the room.
Upper and lower modules may be mounted on the rear of an Egenera BladeFrame. Liebert XDCF
modules use R-134a refrigerant. When attached to a fully loaded BladeFrame EX rack, each Liebert
XDCF module has a nominal cooling capacity of 10kW (2.8 tons; 34,000 BTUh). Performance is based
on:
• Entering fluid temperature—55°F (12.8°C) and
• Dew point—50°F (10°C) or lower.
Liebert XDCF modules consist of a sheet-metal frame, coil and filter dryer. It has no moving parts
and needs no electricity.
The Liebert XDCF system (see Figure 49 below) consists of:
•
•
•
•
Liebert XDCF Modules—upper and lower models are available
Flex Pipe—connects Liebert XDCF modules to supply and return piping
Liebert XD Piping—delivers pumped R-134a refrigerant through flexible piping
Liebert XDP or Liebert XDC—supplies R-134a refrigerant to Liebert XDCF modules
(see Liebert XDP or Liebert XDC user manual for required chiller or drycooler)
Figure 49 Liebert XDCF generic piping layout
To Chiller,
Condenser
or Drycooler
To Chiller,
Condenser
or Drycooler
Liebert XDC
or
Liebert XDP
Liebert XDC
or
Liebert XDP
Liebert XD
Cooling Module *
Pumped
Refrigerant
R134 a
Liebert XD
Cooling Module *
Supply
Lines
Return
Lines
Liebert XD
Cooling Module *
Pumped
Refrigerant
R134 a
Liebert XD
Cooling Module *
49
* Liebert XDCF, Liebert XDH,
Liebert XDO, Liebert XDR
or Liebert XDV
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
4.2
Liebert XDCF Mechanical Considerations
The Liebert XDCF is engineered to fit on the rear of the Egenera BladeFrame enclosure. Figure 50
illustrates the module’s dimensions and the location of pipes. Figure 51 shows the attachment
positions of each module.
Figure 50 Overall dimensions
3-9/16"
(90mm)
7-5/16"
(186mm)
RE TURN
R-134a
Return
Pipe
1-7/16"
(37mm)
TIGHTE N FLE X P IP E
TO UNIT WITH THE
S CHRADE R V ALV E
IN THIS P OS ITION
ONCE FLE X P IP E CONNE CTIONS
ARE MADE TO THE UNIT DO NOT
DIS AS S E MBLE FROM THE UNIT .
RE MOV E CONNE CTIONS FROM
CE ILING HE ADE RS BY TURNING
THE S UP P LY V ALV E TO THE
OFF P OS ITION AND THE N TURNING
THE RE TURN V ALV E TO THE OFF
P OS ITION THE HE ADE R
CONNE CTIONS MAY BE RE MOV E D.
TIGHTE N FLE X P IP E
S UP P LY
TO UNIT WITH THE
S CHRADE R V ALV E
1194311 P1
IN THIS P OS ITION
3-9/16"
(90mm)
TOP
1-7/16"
(37mm)
13-7/16"
(341mm)
Upper module shown;
both upper and lower
modules have same
dimensions
EMERSON
NETWORK POWER
TM
T M
RIGHT
SIDE
Piping is not load-bearing and
should never be used to lift or
move the Liebert XDCF
31-3/8"
(797mm)
BACK
50
Liebert
XD
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
4.3
Liebert XDCF Installation Considerations
No cutting or drilling is required to attach the modules to the rear of the Egenera BladeFrame
cabinet. All mounting holes, slots and pins required are fabricated at the factory.
Liebert XDCF modules attach beside the power modules on the rear of the Egenera BladeFrame (see
Figure 51).
Figure 51 Liebert XDCF module mounting locations
Egenera BladeFrame
Detail Area: B
(Upper Module Mounting Area)
Locator stud for lower
module mounting angle
Captive nuts
for right side
mounting
fasteners
Captive nuts
for right side
mounting
fasteners
Enlarged Detail Area "A"
(Lower Module Mounting Area)
4.4
Detail Area: A
(Lower Module
Mounting Area)
BladeFrame
Power Modules
Enlarged Detail Area "B"
(Upper Module Mounting Area)
Locator stud for upper
module mounting angle
Liebert XDCF Piping Connection Methods and Points
The assembly and connection means used for piping in the Liebert XD system are the same as those
used in conventional refrigeration systems. Observe all standard practices during installation and
startup to prevent damage and contamination.
Supply piping connection is 1/2" OD copper pipe, and return piping connection is 5/8" OD copper. Both
supply and return fittings are one-shot connections. These fittings contain pressurized R-134a
refrigerant inside the Liebert XDCF.
! WARNING
Risk of explosive discharge. Can cause death, injury and equipment damage.
Do not disconnect one-shot connections after they have been connected. Disconnection will
release pressurized R-134a refrigerant from the Liebert XDCF.
The Liebert XDCF has supply and return piping access on the top of each module.
51
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
4.4.1
Header System—Liebert XDCF
The Liebert XDCF module system requires use of the Liebert XD prefabricated piping assembly or
port kit. The prefabricated piping is compatible with the flex pipe required to attach to the Liebert
XDCF modules.
Figure 52 Liebert XDCF supply and return piping access points
Return Pipe
(5/8" diameter)
7-5/16"
(186mm)
3-9/16"
(90mm)
Supply Pipe
(1/2" diameter)
4.5
1-7/16"
(37mm)
Pipe locations and
dimensions are the
same for upper and
lower modules
Liebert XDH Standard Features
• Dual Refrigeration Circuits—Each Liebert XDH has two refrigeration circuits, one in the
upper half of the module and one in the lower half. Dual refrigeration circuits permit altering
cooling levels in response to server room conditions. The dual refrigeration circuits permits
interlaced connection of two refrigerant sources to enhance system reliability.
• Dual Power Cords and Power Inlets—The Liebert XDH is supplied with two (2) detachable
power cords 10 ft (3m) long that attach to two IEC power inlets on the rear of the module. Each
power cord has a NEMA 5-15P (IEC 320-C14) plug at the opposite end. The dual power cords
allow the module to be powered by two separate power sources. If the secondary power cord is
connected to a UPS, the Liebert XDH’s fans will continue to operate if utility power fails.
• Top Piping Access—The Liebert XDH has supply and return piping access on the top of each
module. Supply piping connection is 1/2" OD copper pipe, and return piping connection is 7/8" OD
copper.
• Corner Stabilizers—A stabilizer in each corner permits rolling the Liebert XDH with greater
ease and less chance of tipping.
• Air Diffusers—Two diffusers, one on the upper half of the module and one on the lower half,
enhance flow of cooling air. Uni-directional and bi-directional diffusers are available.
52
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
4.6
Optional Features—Liebert XDH
• Smart Module—Smart modules will allow remote shutdown, fan failure alarms and
automatically switching the second fan bank On and Off. The controls save energy by permitting
the module to turn one fan in each fan bank Off based on the supply and return temperature.
Liebert XD smart modules are able to provide alarm conditions such as fan failure or condensate
detection at the Liebert XDP display via CANbus communication. For electrical connection
details, refer to the Liebert XDH user manual, SL-17210, available on the Liebert Web site:
www.liebert.com
• Refrigerant Precharge—The Liebert XDH can be precharged with refrigerant. The module will
have one-shot fittings and will be pressurized. The one-shot Liebert XD Flex Piping will also be
precharged with refrigerant.
• Field-Installed Flexible Piping (for use with prefabricated piping assemblies)—Field-installed
flexible piping kits are available in lengths of 4, 6, 8 and 10 feet (1.2, 1.8, 2.4 and 3 meters).
Connection style to the module end may be straight or 90 degrees with one-shot style couplings or
removable couplings. Flex pipes with one-shot connections will have pressurized R134a. Flex
pipes with removable connections will have a low pressure nitrogen charge Connection to the
prefabricated piping assembly is with a threaded coupler. For information on acquiring the
correct kit for your installation, refer to DPN000780, available by calling 1-800-LIEBERT and
from your local Emerson representative.
• Tie-Down Bracket—An optional tie-down bracket may be installed on the Liebert XDH to
secure it in the row. The bracket keeps space between the Liebert XDH and adjacent equipment
constant, preventing vibration.
Figure 53 Liebert XDH dimensions
12" (305mm)
80"
(2032mm)
78"
(1981mm)
FRONT
42
(1067mm)
FRONT
53
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
Figure 54
Supply and return piping connections—Liebert XDH
Top of Liebert XDH
Detail “A”
6" (152mm)
3-5/8"
(92mm)
1-3/8"
(35mm)
2"
(51mm)
1/2" Supply, Upper
Refrigeration Circuit
4-1/8"
(104mm)
7/8" Return, Upper
Refrigeration Circuit
Rear
of Liebert
XDH
5"
(126mm)
Rear of XDH
7/8" Return, Lower
Refrigeration Circuit
1/2" Supply, Lower
Refrigeration Circuit
Detail "A"
54
DPN001180
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
4.7
Connecting High-Voltage Wiring—Liebert XDH
The Liebert XDH requires single-phase power for normal operation. The module ships with two power
cords, each 10 feet (3m) long with NEMA 5-15 plugs, which connect to common, three-prong outlets
(see Figures 55 and 56).
Figure 55 Basic Liebert XDH electrical connections
60Hz MODELS ONLY
Field-wiring connections
at terminal strip to be NEC
Class 2. Use switch contacts
with 75VA minimum rating.
50Hz MODELS ONLY
Field-wiring connections
at terminal strip for safety extra
low voltage circuits only. Use
switch contacts rated 75VA
minimum, 24VAC maximum.
Rear Door and
Side Panel not
shown for clarity
Strain relief points
for power cords
IEC Primary
and Secondary
Power Inlets
DPN001180
Pg. 4, Rev. 5
Figure 56 Smart Liebert XDH electrical connections
Condensate Detection,
Remote Shutdown [37,38]
and Alarm Relay Dry
Contacts/Low Voltage
Connections (82 thru 87).
Strain Relief Points
for Power Cords
Primary and
Secondary
Circuit Breaker
IEC Primary
and Secondary
Power Inlets
Bottom Half of the Liebert XDH_S
55
DPN001180
Pg. 4, Rev. 5
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
4.8
Connecting Low-Voltage Wiring—Liebert XDH Smart Modules
Low-voltage connections are available only on the Liebert XD smart module. The low-voltage
connections for Liebert XDH smart modules are in the rear of the modules. There are two connection
locations, one for the lower bank of fans and one for the upper bank of fans. The power connections
are shown in Figure 57; the communication ports are on the rear left side of the Liebert XDH.
These dry contacts can to be connected to a monitoring unit, such as Liebert SiteScan®. Make
connections on these modules according to site-specific drawings. The module must be installed in
accordance with national and local wiring regulations.
Terminal block connections 37, 38 and 82 through 87 can be connected to a monitoring unit, such as
Liebert SiteScan. The remote shutdown, condensate detection alarm, and fan failure alarms operate
independently of each other.
• Contacts 37 and 38 are for remote shutdown.
• Contacts terminals 82, 83 and 84 are activated by the condensate detection alarm.
• T82 is used for normally open contact closure requirements.
• T83 is common.
• T84 is used when normally closed contact closure is required.
• Contacts terminals 85, 86 and 87 are activated by the fan failure alarm.
• T85 is for normally open contact closure requirements.
• T86 is common.
• T87 is used when normally closed contact closure is required. The condensate detection alarm
and the fan failure alarm operate independently of each other.
• P66 and P67 are CAN bus ports.
Figure 57 Low-voltage connections—Liebert XDH smart module
Condensate Detection,
Remote Shutdown [37,38]
and Alarm Relay Dry
Contacts/Low Voltage
Connections (82 thru 87).
P66/P67
Bottom Half of the XDH_S
Top Half of the XDH_S
56
DPN001180
Page 6, Rev 5
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
4.9
Liebert XDO Standard Features
• Micro Channel Heat Exchanger—The Liebert XDO module includes two all-aluminum micro
channel heat exchangers.
• Fan—Air is drawn in the sides of the module through the heat exchangers and is discharged by
the fan to the area below—The Liebert XDO fan tray hinges down to allow access to replace or
service all electrical components.
• Internal Mounting—The Liebert XDO module is typically suspended from the overhead
building structure by inserting field-supplied threaded rods into the internal mounting brackets.
4.10
Optional Features Liebert XDO
• Refrigerant Pre-Charge—The Liebert XDO can be precharged with refrigerant. The module
will have the one-shot fittings and be pressurized. The one-shot Liebert XD Flex Piping will also
be precharged with refrigerant.
• Field-Installed Flexible Piping (for use with prefabricated piping assemblies or port kits)—
Field-installed flexible piping kits are available in lengths of 4, 6, 8 and 10 feet (1.2, 1.8, 2.4 and 3
meters). Connection style to the module end may be straight or 90 degrees with one-shot
connections. Flex pipes with one-shot connections will have pressurized R134a. Connection to the
prefabricated piping assembly is with a threaded coupler. For information on acquiring the
correct kit for your installation, refer to DPN000780, available by calling 1-800-LIEBERT and
from your local Emerson Network Power representative.
• External Mounting Brackets—The Liebert XDO module can be suspended by external
mounting brackets that are attached to the front and rear panels of the module. The external
mounting brackets are optional ship-loose items.
• Smart Modules—The Liebert XDO is available with an optional factory-installed control board.
A Liebert XDO smart module will allow remote monitoring, shutdown, fan failure alarms,
condensate detection and automatically cycling the fan On and Off as the heat load requires.
Liebert XD smart modules are able to provide alarm conditions such as fan failure or condensate
detection at the Liebert XDP display via CANbus communication.
• Lighting Fixture—Field-installable lighting fixtures are available in two voltages, 120V and
277V. The lighting fixture maybe attached to the bottom of the light panel to the left and right of
the fan. Each fixture consists of housing, reflector, ballast and diffuser. Fixtures are compatible
with standard 48" fluorescent bulbs. Bulbs are not included.
57
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
Figure 58
Dimensional data—Liebert XDO hard-piped modules
LEFT SIDE
24-1/8"
(613mm)
REAR
72-1/4"
(1835mm)
RIGHT SIDE
FRONT
LEFT
SIDE
25-3/8"
(645mm)
22-3/8"
(568mm)
24-1/4"
(616mm)
9-3/4"
(248mm)
Figure 59
9-3/4"
(248mm)
FRONT
DPN000771
Dimensional data—Liebert XDO with pre-charged option
LEFT SIDE
24-1/8"
(613mm)
REAR
72-1/4"
(1835mm)
FRONT
RIGHT SIDE
58
RIGHT
SIDE
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
Figure 60
Liebert XDO internal mounting location
26-3/4"
(679mm)
18-1/2"
(470mm)
REAR
7/8" (22mm)
diameter mounting
holes
1"
(25mm)
TOP VIEW
1"
(25mm)
26-3/4"
(679mm)
7/8" (22mm)
diameter mounting holes
FRONT
59
DPN000771
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
Figure 61 Top and front electrical access points and terminal block—standard Liebert XDO modules
Knockouts for high-voltage
connections
TOP
Grounding Lug
High-Voltage
Cover
FRONT
Note:
Access to electrical terminal blocks
is through hinged fan tray
60
DPN000771
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
Figure 62 High-voltage terminal block and connection locations—standard Liebert XDO modules
High-Voltage Cover
High-voltage and low-voltage
terminal blocks viewed from
the interior of the Liebert XDO
Earth-Ground
Location
N
High-Voltage
Terminal Block
Inside detail view with high-voltage cover removed.
For clarity, top is not shown.
Figure 63 Top and front electrical access points—Liebert XDO smart modules
Knockouts for
High-Voltage
Connections,
Standard Liebert
XDO Modules
Front
Knockouts for
Low-Voltage
Connections,
Liebert
XDO Smart Modules
61
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
Figure 64 High-voltage terminal block connection locations—Liebert XDO smart modules
Top of Liebert XDO
Grounding
Lug
High-Voltage
Connections
Rear
of Liebert
XDO
Electric Box
(Access is through
hinged fan tray)
Electric Box
62
DPN000771
Rev. 9
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
4.11
Low-Voltage Wiring—Liebert XDO Smart Modules
Low-voltage connections to the Liebert XDO are available only on smart modules.
Viewing the Liebert XDO from the front or from above, the low-voltage terminal block is on the right
side of the module (see Figure 65). Make low-voltage connections on these modules according to sitespecific drawings. The module must be installed in accordance with national and local wiring regulations.
For Liebert XDO smart modules, the low-voltage connections are on the electric box inside the Liebert
XDO. Knockouts for the low-voltage connections are on the front of the Liebert XDO, near the top (see
Figure 65).
Terminal block connections 37, 38 and 82 through 87 can be connected to a monitoring unit, such as
Liebert SiteScan®. The remote shutdown, condensate detection alarm and fan failure alarms operate
independently of each other.
• Contacts 37 and 38 are for remote shutdown.
• Contacts terminals 82, 83 and 84 are activated by the condensate detection alarm.
• T82 is used for normally open contact closure requirements.
• T83 is common.
• T84 is used when normally closed contact closure is required.
• Contacts terminals 85, 86 and 87 are activated by the fan failure alarm.
• T85 is for normally open contact closure requirements.
• T86 is common.
• T87 is used when normally closed contact closure is required. The condensate detection alarm
and the fan failure alarm operate independently of each other.
• P66 and P67 are CAN bus ports.
Figure 65 Low-voltage wiring—Liebert XDO smart modules
TOP
Rear
of Liebert
XDO
Electric Box
(Access is through
hinged fan tray)
Low-Voltage Terminal Block
Condensate Detection,
Remote Shutdown [37,38] and
Alarm Relay Dry Contacts-low
voltage connections [82 thru 87]
Electric Box
63
DPN000771
Rev. 9
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
4.12
Liebert XDR Standard Features
• Micro-channel Heat Exchanger—The Liebert XDR module includes two all-aluminum
microchannel heat exchanger
• Door Safety Catch—Liebert XDR modules have a door safety catch to prevent the door from
opening beyond 110°. When the door is fully open, the safety catch will hold the door in place. To
release the door, push up on the door catch and close the door.
• Removable Installation Handles—The Liebert XDR will have four installation handles
factory-installed to ease with installation and to be removed in the field after installation onto the
rack to allow side-by-side placement of the racks.
• Rack-Mount Kit—The rack mount kits are constructed of 14-gauge steel to support the
Liebert XDR on the rear of the equipment cabinet and painted black to match the module. The
rack mount kit must be field-installed. Rack-mount kits are available for Knurr Miracel, APC
AR3100, Dell PowerEdge 4210 and HP 10642. Contact the factory by calling 1-800-LIEBERT for
kits to permit mounting on other rack types.
4.13
Optional Features—Liebert XDR
• Refrigerant Pre-Charge—The Liebert XDR can be precharged with refrigerant. The module
will have the one-shot fittings and will be pressurized. The one-shot Liebert XD Flex Piping will
also be pre-charged with refrigerant.
• Field-Installed Flexible Piping—Field-installed flexible piping kits for use with prefabricated
piping assemblies are available in lengths of 4, 6, 8 and 10 feet (1.2, 1.8, 2.4 and 3 meters).
Connection style to the module end may be straight or 90 degrees with one-shot or removable
connections.
Flex pipes with one-shot connections will have pressurized R134a. Flex pipes with removable
connections will have a low-pressure nitrogen charge. Connection to the prefabricated piping
assembly is with a threaded coupler. For information on acquiring the correct kit for your
installation, refer to DPN000781, available from Liebert by calling 1-800-LIEBERT and from
your local Emerson representative.
64
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
4.14
Liebert XDR Installation Considerations
Panels must be installed on the top and bottom of the rack to ensure that the air flows across the
Liebert XDR’s coils. If the panels are not installed, heated air will bypass the coils, drastically
reducing the performance of the Liebert XDR.
Table 25
Cooling capacity, 1500-3000 cfm air flow
Degrees F
Degrees C
Air flow
(cfm)
EAT
(°F)
Capacity
(kW)
LAT
(°F)
Air flow
(cfm)
EAT
(°C)
Capacity
(kW)
LAT
(°C)
1500
86.0
10.3
63.6
1500
30
10.3
17.5
1500
95.0
13.4
65.9
1500
35
13.4
18.9
1500
104.0
16.4
68.4
1500
40
16.4
20.2
1500
122.0
22.5
73.1
1500
50
22.5
22.9
1600
87.8
10.5
66.4
1600
31
10.5
19.1
1600
95.0
13.1
68.4
1600
35
13.1
20.2
1600
104.0
16.2
70.9
1600
40
16.2
21.6
1600
118.4
21.3
75.0
1600
48
21.3
23.9
1800
86.0
10.7
66.7
1800
30
10.7
19.3
1800
95.0
14.1
69.4
1800
35
14.1
20.8
1800
104.0
17.5
72.3
1800
40
17.5
22.4
1800
114.8
21.6
75.7
1800
46
21.6
24.3
2000
84.2
10.6
66.9
2000
29
10.6
19.4
2000
95.0
15.0
70.5
2000
35
15.0
21.4
2000
104.0
18.6
73.6
2000
40
18.6
23.1
2000
111.2
21.5
76.1
2000
44
21.5
24.5
2000
82.4
10.9
64.6
2000
28
10.9
18.1
2000
95.0
16.0
68.9
2000
35
16.0
20.5
2000
104.0
19.6
72.0
2000
40
19.6
22.2
2000
113.0
23.3
75.1
2000
45
23.3
23.9
2200
82.4
10.4
66.9
2200
28
10.4
19.4
2200
95.0
15.8
71.6
2200
35
15.8
22.0
2200
104.0
19.6
75.0
2200
40
19.6
23.9
2200
109.4
21.9
77.0
2200
43
21.9
25.0
2400
80.6
10.1
66.9
2400
27
10.1
19.4
2400
95.0
16.5
72.5
2400
35
16.5
22.5
2400
104.0
20.5
76.1
2400
40
20.5
24.5
2400
107.6
22.1
77.5
2400
42
22.1
25.3
2500
78.8
10.6
65.0
2500
26
10.6
18.3
2500
95.0
18.0
71.6
2500
35
18.0
22.0
2500
104.0
22.1
75.2
2500
40
22.1
24.0
2500
107.6
23.7
76.7
2500
42
23.7
24.8
3000
77.0
10.6
65.5
3000
25
10.6
18.6
3000
86.0
15.0
69.7
3000
30
15.0
20.9
3000
95.0
19.5
73.9
3000
35
19.5
23.3
3000
102.2
23.0
77.2
3000
39
23.0
25.1
55°F Refrigerant, 51°F dew point
12.8°C Refrigerant, 10.6°C dew point
65
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
Figure 66 Liebert XDR dimensions with hard-piped connections
Piping is not load-bearing and
should never be used to lift or
move the Liebert XDR.
4"
(102mm)
1-1/8"
(29mm)
1-5/16"
(33mm)
2-1/8"
(54mm)
1-1/2"
(38mm)
82-3/8"
(2092mm)
78-3/8"
(1991mm)
20-1/2"
(520mm)
25-5/8"
(651mm)
110deg
5-7/8"
(149mm)
6-12"
(165mm)
27-3/8"
(695mm)
23-1/2" (597mm)
27-3/8" (695mm)
NOTE
The handles are for moving the Liebert XDR and can be removed after the module is secured
to the rack.
66
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
Figure 67 Liebert XDR dimensions with one-shot connections (precharged)
Piping is not load-bearing and
should never be used to lift or
move the Liebert XDR.
5-1/8"
(130mm)
1-5/16"
(34mm)
1-1/8"
(29mm)
1-1/2"
(38mm)
2-1/8"
(54mm)
20-1/2"
(520mm)
83-1/2"
(2121mm)
78-3/8"
(1991mm)
25-5/8"
(651mm)
110deg
5-7/8"
(149mm)
6-1/2"
(165mm)
27-3/8" (695mm)
23-1/2" (597mm)
27-3/8" (695mm)
NOTE
The handles are for moving the Liebert XDR and can be removed after the module is secured
to the rack.
67
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
Figure 68 Liebert XDR dimensions with removable connections
1-1/2" (38mm)
Piping is not load-bearing and
should never be used to lift or
move the Liebert XDR.
1-5/16" (33mm)
2-1/8"
(54mm)
1-1/2"
(38mm)
78-3/8"
(1991mm)
7/8" (22mm)
25-5/8"
(651mm)
80"
(2032mm)
110deg
5-7/8"
(149mm)
20-1/2"
(520mm)
6-1/2"
(165mm)
27-3/8" (695mm)
23-1/2" (597mm)
27-3/8" (695mm)
NOTE
The handles are for moving the Liebert XDR and can be removed after the module is secured
to the rack.
68
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
4.15
Liebert XDV Standard Features
• Micro Channel Heat Exchanger—The Liebert XDV module includes one all-aluminum micro
channel heat exchanger.
• Dual IEC Power Cords and Power Inlets—The Liebert 115V, 60Hz Liebert XDV module is
supplied with two detachable, 10 ft (3m) power cords that attach to two IEC power inlets in the
rear of the module. Each power cord has a NEMA 5-15P (IEC 320-C14) plug at the opposite end.
The Liebert 230V, 60/50 Hz Liebert XDV module is supplied with two non-detachable 10 ft (3m)
power cords. This feature allows the module to be powered by two separate power sources.
• Dual Air Inlets—The Liebert XDV module can be configured to allow air to enter from the rear
grille or the bottom of the module.
• Dual Fans—Airflow is provided by two fans on the front of the module.
• Dual Switches—Controls on the front of the module permit the use of one fan or both fans.
• Liebert Foundation Mounting—Two 1/4-20 cage nuts on the underside of module allow direct
attachment to any Liebert Foundation cabinet; bolts provided with Liebert XDV module.
• Mounting Clips for Non-Liebert Cabinets—The Liebert XDV module is supplied with
mounting clips that allow attachment to a non-Liebert cabinet (some drilling may be required).
4.16
Optional Features—Liebert XDV
• Refrigerant Pre-Charge—The Liebert XDV can be precharged with refrigerant. The module
will have the one-shot fittings and will be pressurized. The one-shot Liebert XD Flex Piping will
also be precharged with refrigerant.
• External Mounting Brackets—The Liebert XDV can be suspended from the overhead building
structure. The external mounting brackets are ship-loose items.
• Field-Installed Flexible Piping (for use with prefabricated piping assemblies)—Field-installed
flexible piping kits are available in lengths of 4, 6, 8 and 10 feet (1.2, 1.8, 2.4 and 3 meters).
Connection style to the module end may be straight or 90 degrees with one-shot or removable
connections. Flex pipes with one-shot connections will have pressurized R134a. Flex pipes with
removable connections will have a low pressure nitrogen charge Connection to the prefabricated
piping assembly is with a threaded coupler. For information on acquiring the correct kit for your
installation, refer to DPN000781, available from Liebert by calling 1-800-LIEBERT and from
your local Emerson Network Power representative.
• Smart Module—Liebert XDV smart modules allow remote shutdown, fan failure alarms and
automatically switching the second fan On and Off. This saves energy by permitting the module
to run with one fan and switching on a second fan when the temperature requires both fans for
cooling. Liebert XD smart modules are able to provide alarm conditions such as fan failure or
condensate detection at the Liebert XDP display via CANbus communication. For electrical
connection details, refer to the Liebert XDV user manual, SL-16626, available on the Liebert Web
site: www.liebert.com
69
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
Figure 69 Liebert XDV dimensions
W
DT
PH
DF
DB
H
DPN000770
Liebert XDV With
Pre-charged Option or
Removable Connection
(all dimensions except piping
height are the same as for the
hard-piped setup, see Table 26)
Table 26
Dimensional data
Illustration
Key
Dimension
Measurement,
in. (mm)
DT
Depth Top
39-1/2 (1003)
DB
Depth Bottom
29-5/8 (752)
W
Width
22-7/8 (581)
H
Height
14 (356)
Piping Height, hard-piped
18-5/8 (473)
PH
Piping Height, one-shot
option or removable
connection
19-5/8 (498)
DF
Depth Front
9-7/8 (250)
70
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
Figure 70
Liebert XDV dimensions with one-shot connection
Top of Liebert XDV
SCHRADER VALVE
SUPPLY(IN)
RETURN(OUT)
SCHRADER VALVE
SUPPLY (IN)
RETURN (OUT)
Supply
Connection
1/2"
Detail Area “A”
Return
Connection
5/8"
Detail “A”
Figure 71 Suspending single Liebert XDV from Unistruts
Bolt 3/8" -16; nut and
washer provided in kit
Unistrut
(field-supplied)
Hanger brackets available
from factory; purchased
separately and shipped loose
Bolt a bracket to each
corner of the Liebert XDV
71
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
Figure 72 Suspending single Liebert XDV from the roof structure
3/8"-16 all-thread bolts,
field-supplied, typical
Hanging Liebert
XDV module
To prevent bypass air
from recirculating
through the Liebert XDV
without it passing
through the cabinet,
this space between the
hanging Liebert XDV and
the cabinet must be blocked.
72
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
Figure 73
Alternate mounting methods—mounting multiple Liebert XDV modules
Attach hanger brackets
to each corner of each
Liebert XDV. This
arrangement permits
mounting from either
Unistruts or from
overhead structure.
Double hanger brackets
available from factory;
purchased separately
and shipped loose
10 - 32 x 5/8" length;
factory-supplied
1/4 - 20 x 5/8" length typical, 2;
factory-supplied
10 - 32 x 5/8" length typical, 3;
factory-supplied
Unistrut field-supplied
upper Liebert XDV: 1
lower Liebert XDV: 2
Bolt 3/8"- 16,
nut and washer
factory-supplied
73
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
4.17
High-Voltage Cabling for Liebert XDV
The Liebert XDV ships with two IEC input power cords. IEC power cords connect to receptacles on
the Liebert XDV and to power sources. See Figures 74 and 75 for power connection locations on basic
modules; see Figures 76 and 77 for power connection locations on smart modules.
Figure 74 Electrical connections for CSA-approved Liebert XDV basic modules
Rear of
Liebert XDV
Knockout for
Optional Wiring
IEC Primary and
Secondary
power inlet
Circuit Breaker Location
on Front of XDV Unit,
Primary and Secondary
Circuit Breakers
Rear of
Liebert XDV
DPN000770
Pg. 6, Rev. 10
74
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
Figure 75 Electrical connections for CE-approved Liebert XDV basic modules
Rear of
Liebert XDV
Knockout for
Optional Wiring
Circuit Breaker Location
on Front of Liebert XDV,
Primary and Secondary
Circuit Breakers
Attached Primary and
Secondary power cords.
Power cords not shown
for clarity.
DPN000770
Pg. 8, Rev. 10
Rear of
Liebert XDV
75
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
Figure 76 Electrical connections for CSA-approved Liebert XDV smart modules
Rear of
Liebert XDV
Optional Remote Shutdown (37,38)
Condensate Detection and
Alarm Relay Dry Contacts-Low
Voltage Connections (82 through 87)
Circuit Breaker Location
on Front of XDV,
Primary and Secondary
Circuit Breaker
IEC Primary and
Secondary
Power Inlet
DPN000770
Pg. 7, Rev. 10
76
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
Figure 77 Electrical connections for CE-approved Liebert XDV smart modules
Rear of
Liebert XDV
Optional Remote Shutdown (37,38),
Condensate Detection, and
Alarm Relay Dry Contacts-low
voltage connections (82 thru 87).
Circuit Breaker Location
on Front of Liebert XDV,
Primary and Secondary
Circuit Breaker
Attached Primary and
Secondary power cords
(Power cords not shown
for clarity)
DPN000770
Page 9, Rev. 10
77
Liebert XD Cooling Modules—Liebert XDCF, Liebert XDH, Liebert XDO, Liebert XDR and Liebert XDV
4.18
Low-Voltage Wiring—Liebert XDV Smart Modules
The low-voltage connections for Liebert XDV smart modules are on the rear right side of the modules.
The power connections are shown in Figure 78 and the dry contacts can be connected to a monitoring
module, such as Liebert SiteScan®. Make low-voltage connections on these modules according to
site-specific drawings. The module must be installed in accordance with national and local wiring
regulations.
Terminal block connections 37, 38 and 82 through 87 can be connected to a monitoring unit, such as
Liebert SiteScan. The remote shutdown, condensate detection alarm and fan failure alarms operate
independently of each other.
• Contacts 37 and 38 are for remote shutdown.
• Contacts terminals 82, 83 and 84 are activated by the condensate detection alarm.
• T82 is used for normally open contact closure requirements.
• T83 is common.
• T84 is used when normally closed contact closure is required.
• Contacts terminals 85, 86 and 87 are activated by the fan failure alarm.
• T85 is for normally open contact closure requirements.
• T86 is common.
• T87 is used when normally closed contact closure is required. The condensate detection alarm
and the fan failure alarm operate independently of each other.
• P66 and P67 are CAN bus ports.
Figure 78 Low-voltage connections for Liebert XDV smart modules
Optional Dry Contacts
Low-Voltage Connections
60Hz MODELS ONLY
Field-wiring connections
at terminal strip to be NEC
Class 2. Use switch contacts
with 75VA minimum rating.
50Hz MODELS ONLY
Field-wiring connections
at terminal strip for safety
extra low voltage circuits
only. Use switch contacts
rated 75VA minimum,
24VAC maximum.
78
Liebert XDC and Liebert XDP
5.0
LIEBERT XDC AND LIEBERT XDP
5.1
Liebert XDC Standard Features
• Compressors—Scroll with a suction gas cooled motor, vibration isolators, thermal overloads,
manual reset high-pressure switch and pump down low-pressure switch.
• Refrigeration System—Dual refrigeration circuits each including liquid line filter dryers,
refrigerant sight glass with moisture indicator, electronic control valve, adjustable externally
equalized expansion valves and liquid line solenoid valves.
• Heat Exchanger—Brazed plate design with interwoven circuiting constructed of stainless steel
plates, copper brazed.
• Pumps—Centrifugal type, end suction, canned rotor design.
• Liebert iCOM—The Liebert iCOM offers the highest capabilities in unit control, communication
and monitoring of Liebert Precision Cooling units. The Liebert iCOM is a factory-installed
assembly. Operating conditions and status are indicated on the unit display, which is mounted
either on the unit or on the wall, depending on application details (see the Liebert XDC user
manual, SL-16674, available at Liebert’s Web site: www.liebert.com). The control system also
monitors unit operation and activates an alarm when any of the specified factory preset
conditions are exceeded. The unit includes two temperature-humidity sensors to aid in effective
cooling.
• Liebert Lee-Temp™ Refrigerant Control Air-Cooled Condenser—The Liebert Lee-Temp
head pressure control system is designed to maintain proper operating head pressures in outdoor
temperatures down to -30°F (-34.4°C). The condensers utilize head pressure control valves, extra
refrigerant and insulated refrigerant receivers with heater pads. It works by flooding the
condenser coil with liquid refrigerant to a level that balances the system condensing requirements
with the condenser coil surface available to reject the system heat. During the summer, the
system requires the entire condenser coil surface for heat rejection and most of the refrigerant is
stored in a receiver. In the winter, the same amount of heat can be rejected by only a fraction of
the coil surface. As head pressure begins to fall, the control valve restricts the flow of liquid
refrigerant exiting from the condenser. This extra liquid refrigerant reduces the effective
condenser surface area available for heat transfer. The head pressure control valve also bypasses
hot gas into the receiver to warm the liquid and maintain liquid pressure for proper operation of
the expansion valve. Condenser fan controls are either fan cycling on ambient temperature or
constant on.
79
Liebert XDC and Liebert XDP
5.1.1
Liebert XDC Optional Features
• Water / Glycol Condensers—A water/glycol floor stand condenser option is available for heat
rejection requirements. The water/glycol floor stand can be installed beneath the Liebert XDC or
nearby.
Figure 79 Dimensional data
B
Overall
A
Overall
C
F
Height
of Unit
Recommended minimum
hot gas supply and liquid
return piping opening
1"
(25.4mm)
D
17"
(431.8mm)
5"
(127mm)
2"
(50.8mm)
Shaded areas indicate
a recommended
clearance of 36in (914mm) for
component access.
E
Unit Base
D
Unit Base
FLOOR CUTOUT DIMENSIONS
DPN001599
Pg. 2, Rev. 4
UNIT DIMENSIONAL DATA
Table 27
Liebert XDC dimensions, weight
Air-Cooled
Model
*
Shipping Weight
lb. (kg)
Dimensional Data, inches (mm)
50/60Hz
A
B*
C
D
E
F
Domestic
Export
XDC160
74 (1880)
34 (864)
33-1/8 (841)
33 (838)
72 (1829)
78 (1981)
1945 (882)
2093 (949)
Dimension does not include the bezel of the disconnect switch, the handle or the control bezel.
Table 28
Liebert XD Chiller dimensions, weight
Dimensional Data, inches (mm)
Shipping Weight, lb (kg)
Air Cooled Model
A
B*
C
D
E
Domestic
Export
Liebert XDC160
74 (1880)
34 (864)
33-1/8 (841)
33 (838)
72 (1829)
1945 (882)
2093 (949)
* Dimension does not include the bezel of the disconnect switch.
80
Liebert XDC and Liebert XDP
Figure 80 Piping locations
** To first cooling module or
bypass flow controller
Install Replaceable Filter Drier Assembly
in Liquid Supply Line
22"
(559mm)
DIMENSIONS ARE
SUBJECT TO CHANGE
WITHOUT NOTICE
* Orientation
Defined by
Installer
21" (533mm)
A - Return Line From
Cooling Units (Line
is spin closed; elbow
is customer-provided)
3-1/4"
(83mm)
8"
(203mm) *
B - Liquid Supply Line
To Cooling Units
47"
44"
(1194mm) (1118mm)
6" (152mm)
23"
(584mm)
C - Hot Gas
Refrigerant
Lines
Table 29
D - Liquid
Refrigerant
Lines
* Allow 8" (204mm) of clearance
for filter replacement. Filter assembly
may be positioned horizontally.
** To ensure all refrigerant flow is filtered,
install the filter drier assembly between
the discharge line of the Liebert XDC
and the first bypass flow controller or
the first Liebert XD cooling module.
DPN001599
Pg. 3, Rev. 4
Liebert XDC piping connection sizes
Piping Outlet Connection Sizes, OD Cu, inches
50/60Hz
A
B
C
D
XDC160
2-1/8
1-1/8
1-3/8
7/8
Source: DPN001599
81
Liebert XDC and Liebert XDP
Figure 81
Positioning a water/glycol Liebert XDC for placement on a floor stand
A - Return from
Cooling Units
B - Supply to
Cooling Units
44"
47"
(1118mm)
(1194mm)
6"
(153mm)
23"
(584mm)
C - Hot Gas
Refrigerant Lines
D - Liquid
Refrigerant Lines
Customer
Water
Supply
E - Threaded
Female
Connections
Customer
Water
Return
F - Cup Fitting
Capillary Lines are 48" (1220mm)
Limit Valve Distance from Condensers
Customer Provided Piping
DPN001419
Pg.1, Rev. 3
Table 30
Liebert XDC Water/Glycol Piping Connection Sizes
Piping Outlet Connection Sizes, OD Cu, inches
Model
A
B
C
D
E*
F**
XDC160
2-1/8
1-1/8
1-3/8
7/8
2-1/2
2-1/8 or 2-5/8
* Threaded Female Connection
** 2-1/8" for 1" WRV, 2-5/8" for 1-1/4" WRV
82
Liebert XDC and Liebert XDP
Figure 82
Piping locations—floor stand and valve assembly
33"
(838mm)
72"
(1828mm)
24" Nominal
(609mm)
TOP VIEW OF FLOOR STAND
Hot Gas 1
Hot Gas 2
Shaded areas indicate a recommended
clearance of 36" (915mm) for component
access and water/glycol piping.
Liquid 1
Liquid 2
33" (838mm)
Outlet
20-1/4"
(514mm)
10-1/2"
(267mm)
6-1/2"
(165mm)
Circuit 1
12-5/16"
(313mm)
26-15/16" (684mm)
LEFT SIDE OF CABINET
Circuit 2
Inlet
FLOOR STAND CONNECTIONS
83
2-1/4" - 5-1/4"
(57 - 133 mm)
DPN001419
Liebert XDC and Liebert XDP
Figure 83 Front view of Liebert XDC and electrical enclosures
Secondary Disconnect Switch
Primary Disconnect Switch
Liebert iCOM Display
Enclosure
Cover
Latch
PRIMARY ELECTRICAL
ENCLOSURE
COMPRESSOR SECTION
Figure 84
Hazardous
Voltage
Enclosure Cover
Hazardous
Voltage
Enclosure
Cover
SECONDARY ELECTRICAL
ENCLOSURE
PUMP SECTION
Liebert XDC electrical enclosure knockout locations for field wiring
Knockout for
Input Power
Enclosure Cover
Not Shown for Clarity
84
Liebert XDC and Liebert XDP
Figure 85 Liebert XDC high-voltage connections—primary disconnect switch, 60Hz models
Transformer 3 (T3)
Fuse Block
Customer Power
Connection
Primary
Power Block
Compressor
Fuse Blocks
Ground
Lug
Primary
Fused
Disconnect
Compressor
Contactors
Transformer 3 (T3)
Electronic Hot Gas
Bypass Controllers
Figure 86 Liebert XDC high-voltage connections—primary disconnect switch, 50Hz models
Compressor
Circuit Breakers
Transformer 3 (T3)
Circuit Breaker
Transformer 3 (T3)
Customer
Power Connection
Busbar
Ground
Lug
Primary
Disconnect
Switch
Compressor
Contactors
Electronic Hot Gas
Bypass Controllers
85
Liebert XDC and Liebert XDP
Figure 87 Liebert XDC high-voltage connections—secondary disconnect switch, 60Hz models
Power Connection from
Primary Power Block
Power Block
Ground
Lug
Transformer 2 (T2)
Secondary
Fused
Disconnect
Transformer 3 (T3)
Fuse
Blocks
Transformer 1 (T1)
Pump
Contactors
Figure 88 Liebert XDC high-voltage connections—secondary disconnect switch, 50Hz models
Power Block
Power Connection From
Primary Power Block
Ground Lug
Transformer 2 (T2)
Secondary
Disconnect Switch
Transformer 3 (T6)
Fuse Blocks
Busbar
Pump Contactors
Transformer 1 (T1)
86
Liebert XDC and Liebert XDP
Figure 89
Liebert XDC heat rejection electrical connection points
Heat Rejection Connections
Field-supplied 24V, Class 1 wiring
to interlock heat rejection from pigtails:
70A and 71A - Compressor Circuit #1
70B and 71B - Compressor Circuit #2
70C and 71C - Dual Source Relay (optional)
Electrical handy box
factory-installed
with cover
Figure 90 Liebert XDC electrical enclosure knockout locations for Extra Low-Voltage connections
Liebert XD Module Condensate
Connections (optional; depends
on features supplied with
Liebert XD Module)
User Interface Wiring
Temperature/Humidity
Sensor Wiring
Alternate Knockout
for Temperature/Humidity
Sensor Wiring
Enclosure Cover Not Shown for Clarity
87
Liebert XDC and Liebert XDP
Figure 91 Liebert XDC Extra Low Voltage field connection points
To P66 on Liebert iCOM
Control Board
Termination
Plug
To P64 on Liebert iCOM Control Board
Red Ethernet Cable
To Remote
T/H Sensor A
To Liebert XD Cooling
Module and Remote
T/H Sensor B
To Optional
External
Connections
P64
P66 P67
Unit Display (Rear View
Factory-Wired
Temperature Sensor
P67
XD
COOLANT
DO
NOT
USE
1
Notes
Control wiring must be Class 2 and installed
in accordance with the National Electrical Code (NEC)
1
Requires shielded cable
1
88
2
Liebert XDC and Liebert XDP
5.2
Liebert XDP Standard Features
• Heat Exchanger—Brazed plate design with interwoven circuiting constructed of stainless steel
plates, copper brazed.
• Pumps—Centrifugal type, end suction, internally cooled, canned rotor design.
• Cabinet and Frame—Custom powder painted steel panels. A hinged control access panel opens
to a second front panel, which is a protected enclosure for all high-voltage components. Frame is
constructed of 14 gauge heliarc welded tubular steel and painted using an auto-deposition coating
system.
• Liebert iCOM—The Liebert iCOM offers the highest capabilities in control, communication and
monitoring of Liebert Precision Cooling units. The Liebert iCOM is a factory-installed assembly.
Operating conditions and status are indicated on the display, which is mounted either on the
Liebert XDP or on the wall, depending on application details (see user manual, SL-16644). The
control system also monitors unit operation and activates an alarm when any of the specified
factory preset conditions are exceeded.
The Liebert XDP with Liebert iCOM includes two temperature-humidity sensors to aid in
effective cooling.
• CANbus Communication—The Liebert XDP is able to communicate with Liebert XD smart
modules over CANbus. This allows the status of the modules to be viewed from the Liebert XDP
Liebert iCOM display. The Liebert XDP is also able to send remote shutdown signals to the smart
modules. Liebert XD smart modules are able to provide alarm conditions such as fan failure or
condensate detection at the Liebert XDP display.
89
Liebert XDC and Liebert XDP
Figure 92
Liebert XDP dimensions
A
Overall
B
Overall
C
Side Panel
78"
(1981mm)
E
)
mm
127
(
"
5
D
1" (25mm)
2-3/8"
(60mm)
11"
(279mm)
Floor Cutout Dimensions
D
Unit Base
The shaded area indicates
a recommended clearance
of 36" (914mm) for component
access.
E
Unit Base
Unit Dimensional Data
Table 31
DPN001598
Liebert XDP dimensions
Dimensional Data inches (mm)
Shipping Weight, lb (kg)
Model
A
B*
C
D
E
Domestic
Export
Liebert
XDP160
38 (965)
34 (864)
33-1/8 (841)
33 (838)
36 (914)
990 (449)
1067 (484)
* The dimension does not include the bezel of the disconnect switch.
90
Liebert XDC and Liebert XDP
Figure 93 Liebert XDP piping access points and external features
To first cooling module
or bypass flow controller **
To first cooling
module or bypass
flow controller **
Install replaceable
filter dryer assembly
in liquid supply line B.
Close this
valve during
normal
operation
Orientation
determined
by installer *
* Orientation
determined
by installer.
A - Return from Liebert XD
cooling modules
Orientation
determined
by installer *
B - Supply to Liebert XD Cooling Modules
17-1/4"
(438mm)
Emerson recommends field-installation
of shutoff valves at these points to permit
isolating the Liebert XDP for maintenance
16-1/8"
(409.6mm)
10" (254mm)
19"
(483mm)
Dimensions are
approximate
and subject to change
without notice.
* Allow 8" (204mm) clearance for filter replacement.
** To ensure ensure all refrigerant flow is filtered,
install the filter dryer assembly between the discharge
line of the Liebert XDP and the first bypass
flow controller or the first Liebert XD cooling module.
*** For each Liebert XDP unit, a separate
20-40 mesh strainer is REQUIRED in the
chilled water supply from the chilled water
source. The strainer is field-supplied and
field-installed. The maximum distance
of the strainer is 10 feet (3m) from the
Liebert XDP.
D - Chilled Water Return
To Chilled Water Source
C - Chilled Water Supply
From Chilled Water Source
DPN001598
Pg. 3, Rev. 7
Strainer ***
Table 32
Unit piping outlet connection sizes, inches, OD Cu
Pipe Connection Point
Model
A
B
C
D
Liebert
XDP160
2-1/8
1-1/8
2-5/8
2-5/8
91
Liebert XDC and Liebert XDP
Figure 94
Front view of Liebert XDP and electrical enclosure
Disconnect
Switch
iCOM
User
Interface
Enclosure Cover
Latch
Hazardous Voltage
Enclosure Cover
Front of Liebert XDP
DPN001598
Figure 95 Liebert XDP electrical enclosure knockout location for hazardous voltage wiring
Liebert XDP
Input Power
Knockout
Enclosure Cover
Not Shown for Clarity
92
Liebert XDC and Liebert XDP
Figure 96
Liebert XDP electrical enclosure knockout locations for field wiring
User Interface
(Wall Box) Wiring
Liebert XD Module Condensate
Connections (optional;
depends on features
supplied with Liebert XD Module)
Temperature/Humidity
Sensor Wiring
Liebert XDP
Input Power
Knockout
Alternate Knockout
for Temperature/Humidity
Sensor Wiring
Enclosure cover
not shown for clarity
Figure 97
Liebert XDP high-voltage connections—60Hz
Power Block
Customer
Power
Connection
Ground
Lug
Transformer 2
(Supplied on 460V
Units Only)
Fused
Disconnect
Transformer 6
Fuse
Blocks
Transformer 1
Fuse
Block
Pump
Contactors
93
Liebert XDC and Liebert XDP
Figure 98
Liebert XDP high-voltage connections—50Hz
Customer Power
Connection
Ground Lug
Transformer 2
Disconnect Switch
Power Block
Pump Circuit
Breakers
Transformer 6
Busbar
Fuse Blocks
Transformer 1
Pump Contactors
94
Heat Rejection
6.0
HEAT REJECTION
6.1
Liebert Lee-Temp™ Refrigerant Control Air-cooled Condensers
The Liebert XDC requires two air-cooled condensers per unit. Each condenser requires one receiver.
6.1.1
Liebert Lee-Temp Refrigerant Control Air-Cooled Condenser
The Liebert Lee-Temp head pressure control system is designed to maintain proper operating head
pressures in outdoor temperatures down to -30°F (-34.4°C). The condensers utilize head pressure
control valves, extra refrigerant and insulated refrigerant receivers with heater pads. It works by
flooding the condenser coil with liquid refrigerant to a level that balances the system condensing
requirements with the condenser coil surface available to reject the system heat. During the summer,
the system requires the entire condenser coil surface for heat rejection and most of the refrigerant is
stored in a receiver. In the winter, the same amount of heat can be rejected by only a fraction of the
coil surface. As head pressure begins to fall, the control valve restricts the flow of liquid refrigerant
exiting from the condenser. This extra liquid refrigerant reduces the effective condenser surface area
available for heat transfer. The head pressure control valve also bypasses hot gas into the receiver to
warm the liquid and maintain liquid pressure for proper operation of the expansion valve. Condenser
fan controls are either fan cycling on ambient temperature or constant on.
6.1.2
Standard Features-All Condensers
Table 33
Receivers and head pressure kits for Liebert Lee-Temp condensers
Outdoor Ambient
°F (°C)
Condenser
Model 50/60Hz
Condenser
Qty
Receiver
Part #
Receiver
Qty
Head
Pressure Kit
Head
Pressure
Kit Qty
-30 to 100 (-34 to 38)
DCSL415
2
185010G2 1/G4 2
2
179711G1
2
2
179713G1
1/G2 2
1
179711G2
2
2
181610G2 1/G4 2
2
179711G1
2
-30 to 105 (-34 to 41)
35 to 105 (2 to 41)
DCSL616
DCSL616
1. 120V heater
2. 230V heater
Liebert condensers consist of condenser coil(s), housing, propeller fan(s) direct-driven by individual
fan motor(s), electrical controls and mounting legs. Liebert air-cooled condensers provide positive
refrigerant head pressure control to the Precision Cooling indoor unit by adjusting heat rejection
capacity. Various methods are employed to match indoor unit type, minimum outdoor design ambient
and maximum sound requirements.
6.1.3
Condenser Coil
Liebert-manufactured coils are constructed of copper tubes in a staggered tube pattern. Tubes are
expanded into continuous, corrugated aluminum fins. The fins have full-depth fin collars completely
covering the copper tubes, which are connected to heavy wall Type “L” headers. Inlet coil connector
tubes pass through relieved holes in the tube sheet for maximum resistance to piping strain and
vibration. Coils are either single circuit or dual circuit, depending on the application. The hot-gas and
liquid lines are spun shut at the factory and include a factory-installed Schrader valve. Coils are
factory leak-tested at a minimum of 300 psig (2068kPag), dehydrated, then filled and sealed with a
nitrogen holding charge for shipment.
6.1.4
Housing
The condenser housing is fabricated from bright aluminum sheet and divided into individual fan
sections by full width baffles. Structural support members, including coil support frame, motor and
drive support, are galvanized steel for strength and corrosion resistance. Aluminum legs are provided
for mounting unit for vertical discharge and have rigging holes for hoisting the unit into position. The
unit's electrical panel is inside an integral NEMA 3R weatherproof section of the housing.
95
Heat Rejection
6.1.5
Propeller Fan
Aluminum propeller fan blades are secured to a corrosion-protected steel hub. Fan guards are heavy
gauge, close-meshed steel wire with corrosion resistant PVC finish rated to pass a 675-hour salt spray
test. Fans are secured to the fan motor shaft by a keyed hub and dual setscrews. Fan diameter is
26" (660mm) or less. The fans are factory-balanced and run before shipment.
6.1.6
Fan Motor
The condenser's fan motor is a continuous air-over design equipped with rain shield and permanently
sealed bearing. Die-formed, galvanized steel supports are used for rigid mounting of the motor.
6.1.7
Electrical Controls
Electrical controls, overload protection devices and service connection terminals are factory-wired
inside the integral electrical panel section of the housing. A locking disconnect switch is
factory-mounted and wired to the electrical panel and controlled via an externally mounted locking
door handle. An indoor unit interlock circuit enables condenser operation whenever indoor unit
compressors are active. Only supply wiring and indoor unit interlock wiring are required at condenser
installation.
6.2
Mechanical Considerations
6.2.1
Dimensions
Figure 99
Condenser planning dimensional data—Four-fan units
43-9/16"
(1106mm)
171-1/2"
(4356mm)
70"
(1778mm)
37-7/8"
(962mm)
Eyebolts
for Lifting
18"
(457mm)
164"
(4166mm)
43-3/16"
(1097mm)
Note:
Overall height to the top of fan guard
43-1/8" (1095mm)
See Figure 101 for typical
condenser footprint dimensions.
ANCHOR PLAN
82" (2083mm)
42"
(1067 mm)
Electric
Box
End
Emerson recommends a
clearance of 36" (915mm) on
each side for proper operation
and component access.
80"
(2032mm)
Four-Fan
Condenser
Legs supplied with
Liebert Lee -Temp
option only
96
41-3/16"
(1046 mm)
Heat Rejection
Figure 100 Condenser planning dimensional data—Six-fan units
87-1/8"
(2213mm)
131-1/2"
(3340mm)
37-7/8"
(962mm)
59"
(1499mm)
18"
(457mm)
Emerson recommends a
clearance of 36" (915mm) on
each side for proper operation
and component access.
124"
(3150mm)
86-3/4"
(2203mm)
Overalll height to the top
of the fan guard is 43-1/8” (1095mm).
ANCHOR PLAN
42"
(1067mm)
122" (3099 mm)
See Figure 101 for typical
condenser footprint dimensions.
Electric
Legs supplied with
Box
Liebert Lee -Temp
End
option only
Figure 101 Typical condenser footprint—dimensions
1”
(25.4mm)
1-3/4”
(44.5mm)
4-1/4”
(108mm)
2”
(50.8mm)
1-3/4”
(44.5mm)
9/16" (14mm)
Typical Diameter
4-1/4”
(108mm)
2”
(50.8mm)
97
Six-Fan
Condenser
84-3/4"
(2153mm)
Heat Rejection
Table 34
Condenser weights and connections
Outdoor
Ambient
°F (°C)
Connection
Size, OD, In.
Model
50/60Hz
Number
of Fans
Hot Gas
-30 to 100
(-34 to 38)
DCSL415
4
-30 to 105
(-34 to 41)
DCSL616
35 to 105
(-34 to 41)
DCSL616
Receiver Part #
Receivers
per
Condenser
Net
Weight
lb (kg)
840 (381)
185010G2 1 / G4 2
1
260 (118)
(2) 1-1/8
1380 (626)
179713G1 1 / G2 2
1
424 (192)
(2) 1-1/8
1380 (626)
181610G2 1/ G4 2
1
200 (91)
Liquid
Net Weight
lb (kg)
1-3/8
1-1/8
6
(2) 1-5/8
6
(2) 1-5/8
1. 120V
2. 230V
Table 35
60Hz electrical condenser data—Liebert Lee-Temp controlled/fan-cycling
Model #
083, 104, 28K
165, 205, 60K
251, 308, 90K
415, 510
616
830, 1010
# of Fans
1
2
3
4
6
8
Input
Voltage ph FLA WSA OPD FLA WSA OPD FLA WSA OPD FLA WSA OPD FLA WSA OPD FLA WSA OPD
208/230
460
575
3.5
3
4.4
15
7.0
7.9
15
10.5 11.4
15
14.0 14.9
20
21.0 21.9
25
28.0 28.9
35
1.7
2.1
15
3.4
3.8
15
5.1
5.5
15
6.8
7.2
15
10.2 10.6
15
13.6 14.0
20
1.4
1.8
15
2.8
3.2
15
4.2
4.6
15
5.6
6.0
15
8.4
15
11.2 11.6
15
8.8
FLA = Full Load Amps; WSA = Wire Size Amps; OPD = Maximum Overcurrent Protection Device
Table 36
50Hz condenser full load amp values
Condenser
Control Type
Liebert Lee Temp
Controlled/Fan-Cycling
Input Voltage - Phase
Model #
# of Fans
200/230-3
380/415-3
415
4
14.0
6.8
616
6
21.0
10.2
Table 37
Liebert Lee-Temp receiver electrical data, 50Hz and 60Hz
Rated Voltage - Single Phase
120
200/208/230
Watts/Receiver
150
300
450
150
300
450
Full Load Amps
1.4
2.8
4.2
0.7
1.4
2.1
Wire Size Amps
1.8
3.5
5.3
0.9
1.8
2.7
Maximum Overcurrent
Protection Device, Amps
15
15
15
15
15
15
The Liebert Lee-Temp receiver requires a separate power feed for heaters. The condenser is not designed to supply power to the receiver.
98
Heat Rejection
6.3
Heat Rejection Piping
6.3.1
Piping for Direct Expansion (DX) Circuit—R-407C Air-Cooled Units
! WARNING
Risk of refrigerant system explosion or rupture from overpressurization. Can cause
equipment damage, injury or death.
Installer must install a 400 psig pressure relief valve in each of the two R-407C refrigerant
circuits of the Liebert XDC system. Do not install shutoff valves between the compressors and
the pressure relief valves.
For systems requiring EU CE compliance, the pressure relief valves must be CE-certified by a
notified body to the EU Pressure Equipment Directive.
6.4
Install Double Discharge Risers
For air-cooled systems, double discharge risers must be installed in the hot gas lines that have
vertical heights of 15 feet (4.6m) or more (see Figure 102). This will allow proper oil return to the
compressors when the system is running at low loads. A double riser system is constructed of a large
diameter riser with a trap at the base and a riser with a smaller diameter in parallel.
At full-load operation, the refrigerant vapor flows up both risers at velocities that are adequate to
carry the oil. At low loads, refrigerant vapor velocities are lower and the trap at the bottom of the
riser becomes filled with oil. When this happens, refrigerant flows up only the smaller riser.
The trap at the top of the riser must be tied into the top of the line to prevent oil from filling the larger
riser. For each double riser used, the maximum height of the riser must not exceed 15 feet (4.6m).
Multiple risers must be installed in series as the height of the hot gas line increases. Total maximum
height of the hot gas line must not exceed 60 feet (18.3m).
Horizontal discharge lines should be pitched downward in the direction of flow to aid in oil drainage
with downward pitch of at least 1/2 inch in 10 feet (13mm in 3m).
Figure 102 Double discharge riser layout
Connection point of upper trap
is at the top of the line
Smaller riser is
5/8" O.D. copper
Larger riser 1-1/8"
O.D. copper
Trap size is 1-1/8" large riser size with minimum internal
Contact your local Liebert representative for factory approval whenever a refrigerant piping run
exceeds 200 feet (60m) equivalent length or when condensers must be installed below the level of the
cooling coil.
99
Heat Rejection
For Air-Cooled Liebert Lee-Temp / Flood Back Head Pressure Control Units Only
! WARNING
Risk of explosive discharge from high-pressure refrigerant. Can cause injury or death.
This unit contains fluids and/or gases under high pressure.
Relieve pressure before working with piping.
NOTICE
Risk of refrigerant contamination. Can cause equipment damage and operational problems.
Refrigerant R-407C is a blend of three components and must be introduced and charged from
the cylinder only as a liquid.
Refrigerant R-407C uses a POE (polyolester) lubricant. Do not open the compressor unit
piping to the atmosphere for more than 15 minutes. The compressors contain POE oil that is
very hygroscopic; it quickly absorbs water from the atmosphere. The longer the compressor
piping is open to the atmosphere, the harder it will be to fully evacuate. If left open too long,
the POE oil may need to be replaced before achieving the required vacuum level.
POE oils also have a property that makes them act as a solvent in a refrigeration system.
Maintaining system cleanliness is extremely important because the oil will tend to bring any
foreign matter back to the compressor. Refer to the ASHRAE refrigeration handbook for
general good-practice refrigeration piping.
Table 38
Receivers and head pressure kits for Liebert Lee-Temp condensers
Outdoor Ambient
°F (°C)
Condenser
Model 50/60Hz
Condenser
Qty
Receiver
Part #
Receiver
Qty
Head
Pressure Kit
Head
Pressure
Kit Qty
-30 to 100 (-34 to 38)
DCSL415
2
185010G2 1/G4 2
2
179711G1
2
2
179713G1
1/G2 2
1
179711G2
2
2
181610G2 1/G4 2
2
179711G1
2
-30 to 105 (-34 to 41)
35 to 105 (2 to 41)
DCSL616
DCSL616
1. 120V heater
2. 230V heater
100
Heat Rejection
Figure 103 Installation data—Liebert Lee-Temp, one-circuit, four-fan model
Field-supplied main disconnect switch in
accordance with local codes or main unit
switch ordered as optional equipment
factory-installed in condenser control box.
* Liquid line from
condenser (Circuit 1)
4
B
6
See
Note 12
See
Note 14
* Hot Gas Line
From Unit
(Circuit 1)
C
Electrical service
by others
Liebert Lee-Temp
heater pad
electric box
this end (See Page 3)
* Hot Gas Line to
Condenser (Circuit 1)
For DCSL616 condenser piping
connections, see Figures 107 and 108.
Mounting Instructions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Liquid Line (Circuit 1) See Note 14
Hot Gas Line (Circuit 1)
See
Liquid Return Note 14
A
Line to Unit
D (Circuit 1)
Position elbow
to direct relief
valve downward
Uncrate carton and inspect for damage to condenser and
condenser control panel
Assemble legs per instructions as shown.
Double risers are required when hot gas vertical rise is
15 ft (4.6m) or more. Refer to Liebert XDC user manual
for double riser details.
Wire according to electrical diagram on inside of
condenser control box and in accordance with all local
codes.
All condenser locations more than 200ft. (61m) of
equivalent piping length from Liebert XDC must consult
factory for special piping considerations.
Field to size refrigerant lines so as not to exceed 2°F
(1.1°C) saturation loss for total equivalent length (do not
use connection sizes to determine line sizes).
Condenser must be installed above or at the same level
as the Liebert XDC.
Do not run piping or wiring in the path of air flow
because it will hamper the system performance.
Install field-supplied inverted traps on hot gas lines
between condenser and field piping.
All other piping field supplied and connected.
Inverted traps must be installed to allow proper
clearance to fully open condenser control box door and in
accordance with local electric codes.
Secure Liebert Lee-Temp receiver assembly and each
leg to condenser frame using hardware provided.
Receiver can be mounted on either side of the condenser.
Liebert Lee-temp Item B is shipped as a pre-piped
assembly shipped loose for field installation. Item C is
shipped loose for field installation.
Fasten liquid and hot gas lines using flat surface clamps
with isolators (field-provided). Support field piping
separately to avoid coil damage and loss of charge.
Relieve pressure at access port. Replace access port
fitting with relief valve before charging system.
101
Ensure piping stays below electrical
box and does not protrude
Metal
Clamp
Isolator
Note 14
DPN000937
Pg. 1, Rev. 11
Factory-Supplied Material
1.
2.
3.
4.
5.
6.
7.
Built-in condenser control box. See electrical drawing
for details and field wiring.
Air-cooled condenser
Piping access cover to be reinstalled when piping is
completed.
Bolts: 4 per leg) 3/8" (9. 5mm); sixteen 5/8" (15.9mm)
Terminal block for 2-wire 24V interlock connection
between Liebert XDC and Liebert condenser
Condenser Legs: 8 legs for four-fan models
Liebert Lee-Temp:
A. Insulated storage receiver - storage receiver one
per circuit; 5-foot-long receiver is standard
B. Dual head pressure control valve assembly with
integral check valve(s), one per circuit (see
Note 13)
C. Rotalock valve, one per circuit, field-installed
D. Pressure relief valve, one per circuit,
field-installed
E. Liquid level indicator, one per circuit,
factory-installed on receiver
Heat Rejection
Figure 104 Installation data—Liebert Lee-Temp, one-circuit, high ambient six-fan model
Field-supplied main disconnect
switch in accordance with local
codes or main unit switch
ordered as optional equipment
factory-installed in condenser
control box
* Liquid line from
condenser
(Circuit 1)
B
* Hot gas line
from unit
(Circuit 1)
5
See
Note 14
Liebert Lee-Temp Heater
Pad Electric Box
* Hot gas line
this end (See
to condenser
DPN000937, Pg. 3)
(Circuit 1)
96" (2438mm) receiver
shown; some systems
use smaller receivers
Mounting Instructions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
C
5
D
Position elbow
to direct relief
valve downward
Hot gas line
(Circuit 1)
See Note 14
7
A
Liquid return
line to unit
(Circuit 1)
Metal
Clamp
Uncrate carton and inspect for damage to condenser and
condenser control panel
Assemble legs per instructions as shown.
Double risers are required when hot gas vertical rise is
15 ft (4.6m) or more. Refer to Liebert XDC user manual
for double riser details.
Wire according to electrical diagram on inside of
condenser control box and in accordance with all local
codes.
All condenser locations more than 200ft. (61m) of
equivalent piping length from Liebert XDC must consult
factory for special piping considerations.
Field to size refrigerant lines so as not to exceed 2°F
(1.1°C) saturation loss for total equivalent length (do not
use connection sizes to determine line sizes).
Condenser must be installed above or at the same level
as the Liebert XDC.
Do not run piping or wiring in the path of air flow
because it will hamper the system performance.
Install field-supplied inverted traps on hot gas lines
between condenser and field piping.
All other piping field-supplied and connected.
Inverted traps must be installed to allow proper
clearance to fully open condenser control box door and in
accordance with local electric codes.
Secure Liebert Lee-Temp receiver assembly and each
leg to condenser frame using hardware provided.
Receiver can be mounted on either side of the condenser.
Liebert Lee-temp Item B is shipped as a pre-piped
assembly shipped loose for field installation. Item C is
shipped loose for field installation.
Fasten liquid and hot gas lines using flat surface clamps
with isolators (field-provided). Support field piping
separately to avoid coil damage and loss of charge.
Relieve pressure at access port. Replace access port
fitting with relief valve before charging system.
102
Liquid line (Circuit 1)
See Note 14
Isolator
Electrical service
by others
Ensure piping stays
below electricalbox and
does not protrude
(See Page 5 for piping
connection details)
Note 14
DPN000937
Pg. 2, Rev. 11
See Figure 108 for details on piping connections.
Factory-Supplied Material
1.
2.
3.
4.
5.
6.
7.
8.
Built-in condenser control box. See electric drawing
for details and field wiring.
Air-cooled condenser
Piping access cover to be reinstalled when piping is
completed.
3/8"-16 x 3/4" long bolts, 20 total; attaches legs to
condenser frame
3/8"-16 x 1-1/4" long bolts, 10 total; attaches legs to
receiver; 3/8" nuts, 10 total; 3/8" washers, 20 total
Terminal block for 2-wire 24V interlock connection
between Liebert XDC and Liebert condenser
Condenser Legs: 5 legs for six-fan models
Liebert Lee-Temp:
A. Insulated storage receiver - storage receiver, one
per circuit; receiver size varies
B. Dual head pressure control valve assembly with
integral check valve(s), one per circuit (see
Note 14)
C. Rotalock valve, one per circuit, field-installed
D. Pressure relief valve, one per circuit,
field-installed
E. Liquid level indicator, one per circuit,
factory-installed on receiver
Heat Rejection
Figure 105 Liebert XDC piping schematic and Liebert Lee-Temp heater pad wiring
Inverted Trap
(By Others)
Rotalock Valve Combination
Head Pressure Control
& Check Valve
Condenser
Control Box
Pressure Relief Valve
Lee-temp Winter System
Air-Cooled Condenser
Heater
Pads
Solenoid Valve
Dehydrator
Liquid Level
Indicator
Expansion Valve
External Equalizer
Hand Shutoff
Valve By Others
Sight
Glass
Sensing Bulb
Hot Gas Bypass Valve
Service Valves
Suction Line
Discharge Line
Hot Gas Bypass
Solenoid Valve
Compressor
Liebert XDC Unit
(One Circuit Shown)
Factory Piping
Field Piping
Optional Hot Gas Bypass
Piping Schematic
For receiver kits185010g2, G4 and 181610G2, G4.
Hi Limit Thermostat, typical
Two heater
per receiver
Circuit
1 & 2pads
Standard
Model - 150 watts each
Hi Limit Thermostat Typical
With 2 Heater Pads Per Receiver
L2
L1
L2
Separate Continuous
Electrical Source By Others
Volts
Separate Continuous
115
Electical
Source
L1
200/208/230
By Others
1 Phase 50/60 Hz.
GND
Volts
GND
115
Circuit
1&2
Optional
Model
3 Heater
Padsper
Perreceiver
Receiver
For
receiver
kits
179713G1,
G3.With
Three
heater pads
- 150 watts each 200/208/230
L2
Total
Watts Per Receiver
L2
Standard 300 Watt (2 Heater Pads)
Optional 450 Watt (3 Heater Pads)
L1
GND
Lee-Temp Heater Pad Wiring
103
1 Phase 50/60 Hz
L1
GND
Heater Pad
Wiring Access
DPN000937
DPN000937
Pg.113, Rev. 6
Pg. 8, Rev.
Heat Rejection
Figure 106 General arrangement air-cooled Liebert XDC Liebert Lee-Temp Control
Condenser Coil
* Inverted Trap on discharge
line to extend above base of
coil by a minimum of
7-1/2" (190mm)
* Double Risers every
15ft (4.6m) of rise on hot
gas line only; maximum
rise not to exceed
60ft (18.3m)
Additional Piping
Assembly **
Check
Valve
Head Pressure
Control with
Integral Check
Valve
m
id Fro
u
q
Li turn nser
R e nde
Co
1/4" (6.4mm)
Pressure Relief
Valve
Liebert
Lee-Temp
Receiver
Sight Glass
Some Models Have
Two Sight Glasses
Standard Piping
Assembly **
* Components are not supplied by Liebert
but are recommended for proper circuit
operation and maintenance.
** Components supplied by Liebert;
must be field-installed.
Single XDC Circuit Shown
Factory-Supplied Piping
Field-Supplied Piping
Liquid/Return
Hot Gas/Discharge
Table 39
Rotalock Valve **
DPN000937
Pg. 3, Rev. 11
Recommended refrigerant line sizes, DX R-407C, OD copper
Liebert XDC 160
Equivalent
Length, ft., (m)
* Hot Gas Line,
in.
Liquid Line, in.
50 (15)
1-1/8
7/8
100 (30)
1-1/8
1-1/8
150 (45)
1-3/8
1-1/8
200 (60)
1-3/8
1-1/8
* Double risers are required when hot gas vertical rise is 15ft. (4.6m) or more.
Source: DPN000937, Pg. 3, Rev. 11
104
Heat Rejection
Figure 107 DCSL616 piping connections—two refrigerant circuits connected for parallel flow
Condenser
Coil (Circuit 2)
* Inverted Trap on
discharge line to
extend above base of
coil by a minimum of
7-1/2" (190mm)
Condenser Coil
(Circuit 1)
Additional
Piping
Assembly **
Head Pressure
Control with
Integral Check
Valve
* Double Risers every
15 ft (4.6m) of rise on
hot gas line only;
maximum rise not to
exceed 60ft. (18.3m)
m
id Fro
u
q
Li turn nser
R e nde
Co
Rotalock
Valve **
Check
Valve
Liebert
Lee-Temp
Receiver
** 1/4" (6.4mm)
Pressure Relief
Valve
Sight Glass
Some Models Have
2 Sight Glasses
** Standard Piping
Assembly
* Components are not supplied by Liebert
but are recommended for proper circuit
operation and maintenance.
* * Components supplied by Liebert;
must be field-installed.
Single XDC Circuit Shown
Factory-Supplied Piping
Field-Supplied Piping
Liquid/Return
DPN000937
Pg. 4, Rev. 11
Hot Gas/Discharge
Table 40
Recommended refrigerant line sizes for DCSL616
Liebert XDC 160
Equivalent
Length, ft., (m)
* Hot Gas Line,
in.
Liquid Line, in.
50 (15)
1-1/8
7/8
100 (30)
1-1/8
1-1/8
150 (45)
1-3/8
1-1/8
200 (60)
1-3/8
1-1/8
* Double risers are required when hot gas vertical rise is 15 feet or more.
Source: DPN000937, Pg. 4, Rev. 11
105
Heat Rejection
Figure 108 DCSL616 piping connections—two refrigerant circuits connected for parallel refrigerant flow
Liquid Line (Circuit 1)
Hot Gas Line (Circuit 1)
Connect the two refrigerant coils for parallel
refrigerant flow using field-supplied piping.
Refer to Figure 104 for mounting instructions.
Refrigerant lines are to be routed and secured
to prevent excessive vibration and stress at the connections.
106
DPN000937
Pg. 5, Rev. 11
Heat Rejection
6.4.1
Air-Cooled Condenser with Liebert Lee-Temp “Flooded Condenser” Head Pressure
Control System—R-407C (DX) Circuit
The Liebert Lee-Temp system consists of a modulating type head pressure control valves and
insulated receivers with heater pads to ensure operation at ambient temperatures as low as -30°F
(-34.4°C).
Liebert Lee-Temp Piping
Two discharge lines and two liquid lines must be field-installed between the indoor unit and the
outdoor condenser. See Figures 103 and 106 for details.
Liebert Lee-Temp Control Materials Supplied
•
•
•
•
•
•
•
•
Built-in, pre-wired condenser control box
Air-cooled condenser
Piping access cover to be reinstalled when piping is complete
Bolts—four per leg (3/8" x 5/8")
Terminal block for two-wire, 24V interlock connection between unit and condenser
Condensate legs—four with one-fan, six on two-and three-fan models and eight on four-fan models
Bolts—used to mount receiver (3/8" x 1-1/4")
Liebert Lee-Temp system:
• Insulated storage receiver—one per circuit
• Head pressure control assembly (head pressure valves and check valves) - one per circuit
• Service valve—one per circuit
• Pressure relief valve—one per circuit
• Liquid level sight glasses
NOTE
Liebert Lee-Temp heater pads require a separate, continuous electrical source. See nameplate
on unit for proper voltage.
107
Heat Rejection
6.5
Calculating Refrigerant Volume
Using Tables 41, 42 and 43 or 44, calculate the refrigerant charge of the individual sections of the
heat rejection system. Add the calculated charge amounts to determine the amount of R-407C
refrigerant required for one system.
Table 41
Indoor unit refrigerant charge—R-407C
Model 50/60 Hz
Charge/Circuit, lb. (kg)
Liebert XDC160
Table 42
17.5 (8.0)
Outdoor air condenser charge—R-407C
Outdoor Ambient, °F (°C
-30 to 100 (-34 to 38)
-30 to 105 (-34 to 41)
35 to 105 (2 to 41)
Model 50/60 Hz
Receiver Part #
Charge / Circuit, lb. (kg)
DCSL415
DCSL616
DCSL616
185010G2 1 / G4 2
179713G1 1 / G2 2
181610G2 1 / G4 2
200 (91)
254 (115)
164 (75)
1. 120V
2. 230V
Table 43
Air-cooled systems - liquid line charge - R-407C refrigerant per 100ft (30m) of Type ACR
copper tube
O.D., inches
Liquid Line, lb. (kg)
Hot Gas Line, lb. (kg)
3/8
1/2
5/8
3/4
7/8
1-1/8
1-3/8
1-5/8
3.7 (1.7)
6.9 (3.1)
11.0 (5.0
15.7 (7.1)
23.0 (10.4)
39.3 (17.8)
59.8 (27.1
—
2.2 (1.0)
3.1 (1.4)
4.5 (2.0)
7.8 (3.5)
11.8 (5.4)
16.7 (7.6)
Table 44
Indoor water/glycol-cooled module – R-407C refrigerant charge
Model 60 Hz
Charge / Circuit, lb. (kg)
Liebert XDC 160
30.0 (13.2) per circuit
108
Heat Rejection
6.5.1
Liebert XDC DX R-407c Circuit Volume
NOTICE
Risk of improper lubrication. May cause equipment damage.
Liebert XDCs’ refrigerant R-407c circuits with refrigerant charges over 55 lb (24.9 kg) require
additional oil. See Figure 109 for the amount required for various charge levels.
Once the system has been fully charged with refrigerant, use a hand pump to add the
additional oil at the suction side of the system while the system is running.
The amount of oil added by field service must be recorded on a tag attached at the tandem the
amount added along with the date it was added. This will be documented on a tag located at
the tandem compressor and marked “Oil Added Field Service Record.” Refer to the Liebert
XDC user manual, SL-16674, available at Liebert’s Web site, www.liebert.com
Additional Oil Required Per Circuit, Ounces
Figure 109 Additional oil requirements for refrigerant charge
Each circuit contains ZRT250KCE Tandem
140
130
120
110
100
90
80
70
60
40
50
30
20
10
0
0
100
200
300
400
XDC160 System Refrigerant Field Charge Per Circuit, Pounds
To calculate the oil required, use the following formula:
Additional Oil Required per Circuit = (Refrigerant Charge * 0.4 - 22)
Enter the refrigerant charge in pounds to determine the oil required in ounces
NOTICE
Risk of improper compressor lubrication. Can cause compressor and refrigerant system
damage.Failure to use oil types, viscosities and quantities recommended by the compressor
manufacturer may reduce compressor life and void the compressor warranty.
• Do not mix polyol ester (POE) and mineral-based oils.
• Do not mix oils of different viscosities.
Consult Emerson or the compressor manufacturer if questions arise.
6.6
Liebert Drycoolers
The Liebert drycooler is a low-profile, direct-drive propeller fan-type air cooled unit. Constructed with
an aluminum cabinet and a copper-tube aluminum fin coil, the unit is quiet and corrosion resistant.
All electrical connections and controls are enclosed in an integral NEMA 3R rated electrical panel
section of the drycooler.
109
Heat Rejection
6.6.1
Liebert Drycooler Fan Cycling Control
Available on all sizes of standard sound and Quiet-Line drycoolers. A thermostatic control cycles the
fan on a single-fan drycooler in response to leaving fluid temperatures. Two or more thermostats are
employed on drycoolers with two or more fans to cycle fans or groups of fans in response to leaving
fluid temperatures. The thermostat setpoints are listed on the factory-supplied schematic. They
typically range from 35 to 45°F (2 to 7°C) for GLYCOOL applications and 65 to 75°F (18 to 24°C) for
glycol applications.
6.6.2
Pump Controls
Controls for pump(s) up to 7.5hp are built into the same integral electric panel as the drycooler fan
controls. Pump fuses, overload heaters and flow switch (dual pump control models) are included with
the Liebert pump packages or must be field-supplied for field-supplied pumps.
Dual pump option—Provides controls for primary and standby pump. The flow switch senses loss of
flow and switches to the standby pump for continuous system operation in the event of a pump
failure. An internal switch allows manual selection of the lead/lag pump.
6.7
Typical System configurations
The standard glycol-cooled precision air conditioning system includes these major components:
•
•
•
•
•
•
•
•
indoor air conditioning unit with heat exchangers (refrigerant/glycol)
glycol regulating valve
outdoor air cooled drycooler
glycol pump(s)
expansion/compression tank
pump controls
interconnection piping
unit interlock control wiring
Figure 110 shows a typical configuration of multiple indoor units and multiple outdoor drycoolers
using a dual pump package and on a common piping loop.
Additional field-supplied components, such as valves, expansion tank, strainers and flow or pressure
switches are also shown in Figure 110. These components are necessary and should be included
when designing a system with one indoor and one outdoor unit on a piping loop or a system using
multiple indoor and outdoor units on a common piping loop. Larger systems may also benefit from an
air separator (not shown). Refer to SL-10080, available at Liebert's Web site, www.liebert.com, for
further details on required components.
110
Heat Rejection
Figure 110 Typical piping arrangement for Liebert XDC and two DDNT880A
Expansion Tank
______ Gal. (L)
HP
GPM (l/s)
ft.
____(kW) ____ Per Pump @ ____(kPa)
FS
PUMP PACKAGE
Drycooler No. 1 Model ______
GPM (l/s) ____ P: ___ ft (kPa)
Cooling Unit #
Model
GPM (l/s)
P ft (kPa):
Cooling Unit #
Model
GPM (l/s)
P ft (kPa):
See Note 3
Cooling Unit #
Model
GPM (l/s)
P ft (kPa):
Drycooler No. 2 Model ______
GPM (l/s) ____ P: ___ ft (kPa)
Cooling Unit #
Model
GPM (l/s)
P ft (kPa):
LEGEND
Gate Valve
Check Valve
Butterfly Valve
Relief Valve
Union
Ball or Flow Control Valve
FS
P:
Cooling Unit #
Model
GPM (l/s)
P ft (kPa):
Cooling Unit #
Model
GPM (l/s)
P ft (kPa):
Flow Switch
Pressure Drop
Total
GPM
(L/s): _____
Pipe
Diam.: _____ In. (mm)
P: _____ Ft. (kPa)
Cooling Unit #
Model
GPM (l/s)
P ft (kPa):
Cooling Unit #
Model
GPM (l/s)
P ft (kPa):
Cooling Unit #
Model
GPM (l/s)
P ft (kPa):
Cooling Unit #
Model
GPM (l/s)
P ft (kPa):
Cooling Unit #
Model
GPM (l/s)
P ft (kPa):
Cooling Unit #
Model
GPM (l/s)
P ft (kPa):
Strainer/Filter
Notes:
1. Pressure and temperature gauges (or ports for same) are
recommended to monitor component pressure drops and performance.
2. Flow measuring devices, drain and balancing valves to be supplied
by others and located as required.
3. See product literature for installation guidelines and clearance dimensions.
4. Drawing shows dual pump package. Alternate pump packages with more
pumps may be considered; consult supplier
111
DPN000991
Rev. 0
Heat Rejection
6.8
Site Considerations
The drycoolers and pumps should be installed in a location offering maximum security and access for
maintenance.
Avoid ground level sites with public access and areas that contribute to heavy snow or ice
accumulations. Utilize Piggyback drycoolers whenever interior building locations must be used. To
ensure adequate air supply, Emerson recommends that the drycoolers be located in an area with
clean air, away from loose dirt and foreign matter that may clog the coil. In addition, drycoolers
should not be located near steam, hot air or fume exhausts. Drycoolers must not be installed in a pit,
where discharge air is likely to be recirculated through the drycooler or installed where objects
restrict the air inlet free area. Also, the drycoolers should be located no closer than 3 feet (1m) from a
wall, obstruction or adjacent unit (see Figure 111).
The drycooler must be installed on a level surface to ensure proper glycol flow, venting and drainage.
For roof installation, mount the drycooler on suitable curbs or other supports in accordance with local
codes.
Allow adequate space for pump packages, expansion/compression tanks, piping and additional field
supplied devices.
When mounting pump packages, mount on level surface or suitable curbs that will allow cooling
ventilation air to enter from underneath the pump package frame and exit through the louvers.
6.9
Dimensions and Weights
Table 45
Standard drycooler net weights, shipping weights, dimensions and volume, approximate
Domestic Packaging
Model
*D**880
*D**940
No. of
Fans
8
Export Packaging
Net Weight
lb (kg)
Packaged
Weight
lb (kg)
Dimensions
LxWxH
in (cm)
Volume
ft3 (m3)
2330 (1058)
2730 (1239)
2430 (1103)
2910 (1321)
184 x 37 x 97
(467 x 94 x 246)
382
(10.8)
112
Packaged
Weight
lb (kg)
Dimensions
LxWxH
in (cm)
Volume
ft3 (m3)
3230 (1446)
185 x 38 x 97
(470 x 97 x 246)
395
(11.2)
3410 (1548)
Heat Rejection
Figure 111 Drycooler planning dimensional data—Eight-fan units
87-1/8"
(2213mm)
171-1/2"
(4356mm)
37-7/8"
(962mm)
Emerson recommends a
clearance of 36" (915mm)
on each side for proper
operation and component
access.
18"
(457mm)
70" (1778mm)
164"
(4166mm)
1-1/2" (38mm)
diameter
hole for rigging
(typ.4)
86-3/4"
(2203mm)
See Figure 112 for typical
drycooler footprint dimensions.
Anchor Plan
80"
(2032 mm)
82"
(2083mm)
Electric
Box End
Eight-Fan Drycooler
113
84-3/4"
(2153 mm)
Heat Rejection
Figure 112 Typical drycooler footprint—dimensions
1”
(25.4mm)
1-3/4”
(44.5mm)
4-1/4”
(108mm)
2”
(50.8mm)
1-3/4”
(44.5mm)
9/16" (14mm)
Typical Diameter
4-1/4”
(108mm)
2”
(50.8mm)
Figure 113 Piping connections for 8-fan drycoolers
Vent opening
(inlet) (typ.2)
Inlet connection
upper headers (typ.)
Outlet connection
lower headers (typ.)
Table 46
DPN000668
Rev. 1
Standard drycooler piping connection sizes and internal volume
Drycooler
Model #
No. of Internal
Coil Circuits
No. of
Fans
Internal Volume,
gal. (L)
No. of
Inlets/Outlets
880
80*
8
44.0 (166.5)
940
96*
8
52.0 (196.8)
* = Standard Circuiting
114
Inlet & Outlet Connection Size
OD Copper, in.
ID Sweat, in.
4/4
—
2-1/8
4/4
—
2-1/8
Heat Rejection
6.10
Mounting the Drycooler
The drycooler must be installed so that it is level within 1/2" (13mm) to ensure proper glycol flow,
venting and drainage. For roof installation, mount the drycooler on suitable curbs or other supports;
follow all local and national codes. Secure the legs to the mounting surface using a field-supplied 1/2"
(13mm) diameter bolt in each of the two 9/16" (14mm) holes in each leg. See Figure 111 for anchor
dimensions.
6.11
Glycol Piping
! CAUTION
Risk of explosive discharge of high pressure gas and flying projectiles. Can cause building
and/or piping damage and personal injury.
Units are shipped from the factory with a pressurized dry nitrogen holding charge. Carefully
relieve the pressure before cutting into the piping system.
NOTICE
Risk of excessive coolant fluid pressure, improper piping material, and unsupported piping.
Can cause piping rupture, coolant fluid leaks and building and/or equipment damage.
To avoid the possibility of burst pipes, the system installer must supply and install a relief
valve in the system. Galvanized pipe must not be used in glycol systems. To help prevent
piping failures, supply and return lines must be supported such that their weight does not
bear on the piping of the unit or pumps.
6.11.1 Piping Guidelines
Piping between the drycooler, the pump and the indoor unit is required to complete the system and is
to be provided and installed by the system installer. All fluid piping must comply with local codes.
Properly sized pipes will help reduce pumping power and operating costs.
Pipe material choices are typically copper, plastic or steel/black iron. Consult glycol and pipe
manufacturing literature for compatibility and sizing assistance. Galvanized piping should not be
used. Any copper piping installed should be “L” or “K” refrigerant grade copper.
See Figure 110 for a typical piping diagram, depicting multiple indoor units, multiple drycoolers and
dual pumps. Single indoor unit/pump/drycooler systems are also possible.
Drycooler supply and return connections vary in size and number. Refer to Table 46. Emerson
recommends installing manual service shutoff valves at the supply and return connections of each
drycooler and indoor cooling unit. The shutoff valves permit isolating equipment for routine
maintenance and for repairs.
Multiple pump packages require a check valve at the discharge of each pump to prevent back-flow
through the standby pump(s). To extend the service life of the drycooler and the system's pumps,
install filters/strainers in the supply line to the pumps. These filters should have a 16-20 mesh screen
and be a type that can be easily replaced or cleaned.
Installing hose bibs at the lowest point of the system will facilitate filling.
Keep piping runs as straight as possible; avoid unnecessary bends and minimize additional fittings.
Allow for pipe expansion from warm fluids. Piping should be isolated from the building with
vibration-isolating supports. Use soft, flexible material to seal between pipes and wall openings to
prevent pipe damage.
Consideration of the minimum glycol temperature to be supplied from the drycooler and the pipe
routing will determine if the glycol supply and return lines should be insulated. Insulation will
prevent condensation on the glycol lines in low ambient conditions.
Completed piping system should provide maximum leak-prevention. Welded or high-temperature
soldered joints should be used where possible. Threaded pipe joints, if needed, can be made with
tightly drawn Teflon™ tape.
Clean and prepare all pipe connections before joining. Be careful not to allow solder/joining debris to
get inside the lines during the connection process.
115
Heat Rejection
6.11.2 Expansion Tanks, Fluid Relief Valves, Air Management and Other Devices
An expansion tank must be provided for expansion and contraction of the fluid due to temperature
change in this closed system. Vents are required at system high points to vent trapped air when
filling the system. A fluid pressure relief valve is also a necessary piping component.
All systems must have an air management system to ensure proper component operation and system
performance. There are several methods that can be used to manage the air within a closed loop
hydronic system. Depending on the method chosen, the system may include one or more of the
following ancillary components: tank-steel (expansion, compression, diaphragm or bladder), air
separator and air vent.
Consult your local engineer to determine which method will be used and where these components
must be installed.
Depending on the complexity of the system, various other devices may be specified—refer to
site-specific drawings. Some of the devices that may be required are: pressure gauges, flow switches,
automatic air separator, tempering valves, standby pumps and sensors for electrical controls.
NOTICE
Risk of frozen coolant fluid. Can cause piping rupture, coolant fluid leaks and building
damage.
Immediately following the use of water for leak testing or system cleaning, charge the tested
system with the proper percentage of glycol and water for your coldest design ambient.
Complete system drain-down cannot be ensured and damage to the system could result from
freezing of residual water.
6.12
Electrical Supply
Line voltage electrical service is required for all models. Refer to equipment nameplate regarding
wire size and circuit protection requirements. Electrical service must conform to national and local
electrical codes. Refer to electrical schematic when making connections.
Each unit is shipped from the factory with all internal unit wiring completed.
! WARNING
Risk of electric shock. Can cause injury or death.
Disconnect all local and remote electrical power supplies before working within the electrical
enclosure.
The line side of the disconnect remains energized when the disconnect is Off.
Use a voltmeter to verify that the electrical power is Off before performing any electrical
and/or mechanical service and/or maintenance operations.
! WARNING
Risk of high speed moving parts. Can cause injury or death.
The fan(s) blades can start to rotate unexpectedly when the power is On. Disconnect all local
and remote electrical power supplies before working within the fan compartment.
Use a voltmeter to verify that the electrical power is Off before performing any electrical
and/or mechanical service and/or maintenance operations.
Each unit is shipped from the factory with all internal unit wiring completed. Refer to the electrical
schematic supplied with the drycooler when making line voltage supply, low voltage indoor unit
interlock and any low voltage alarm connections. All wiring must be done in accordance with all
applicable local, state and national electrical codes.
For electrical characteristics, refer to Table 47.
116
Heat Rejection
6.12.1 Line Voltage Wiring
! WARNING
Risk of electrical fire and short circuit. Can cause property damage, injury or death.
Select and install the electrical supply wire and overcurrent protection device(s) according to
the specifications on the unit nameplate(s), per the instructions in this manual and according
to the applicable national, state and local code requirements. Use copper conductors only.
Make sure all electrical connections are tight. Unit-specific wiring diagrams are provided on
each unit.
Drycooler rated voltage should be verified with available power supply upon receipt of unit but before
installation. Refer to the unit electrical schematic and serial tag for specific electrical requirements.
All wiring must be done in accordance with all applicable local, state and national electrical codes.
Line voltage electrical service is required for all drycoolers at the location of the drycooler. If the
drycooler contains pump controls, the pump package voltage must match the drycooler voltage. See
the unit's serial tag for specific electrical requirements of the drycooler and any pump package. A unit
disconnect is standard on drycoolers with internal pump controls and optional on all other drycoolers.
Site disconnect(s) may also be required per local code to isolate the drycooler/pumps for maintenance.
Route the supply power to the site disconnect switch and then to the drycooler. Route the conduit
through the hole provided in the cabinet. Connect earth ground to lug provided near terminal board.
Table 47
60Hz electrical values - Eight-fan drycoolers without pump controls, standard models
Model #
880, 940
Voltage
Phase
FLA
WSA
OPD
208/230
3
28.0
28.9
35
460
3
13.6
14.0
20
575
3
11.2
11.6
15
Values are calculated per UL 1995. OPD values may be adjusted higher than calculations to
compensate for maximum anticipated application temperatures.
Table 48
60Hz pump FLA values
Input Power, Volts
Pump
hp
208
460
10
30.8
14.0
Values based on NEC handbook values for 3-phase motors.
6.12.2 Low Voltage Control Wiring
NOTICE
Risk of control malfunction. Can cause improper unit operation.
Make sure that all low voltage electrical wiring has been performed per the schematic
diagram provided and that all low voltage wiring connections are tight.
A control interlock between the drycooler and the indoor cooling units is required. Field-supplied copper wire is required for connection between like-numbered Terminals 70 & 71 on both units for
remote On/Off control of the drycooler, synchronized with the indoor unit. Wiring must be sized and
selected for insulation class per NEC and other local codes. The recommended control circuit wire
(24VAC) size is 16AWG for lengths up to 150ft. (45m). Contact the factory for assistance with longer
wiring runs.
117
Heat Rejection
Table 49
Minimum recommended control circuit wire size, AWG, 60 Hz models
Drycooler Types With Pump Controls
DSF
DDF
1
1
DSO
DDO
Number of Fans
Control Wire
Run, ft (m)
1
2
Number of Fans
3
4
6
8
1
2
3
4
6
8
0-25 (0-7.6)
16
16
16
16
16
16
16
16
16
16
16
16
16
16
26-50 (7.9-15.2)
16
16
16
16
16
16
16
14
16
14
14
14
14
14
51-75 (15.5-22.8)
16
16
16
16
16
16
14
14
14
14
14
12
14
14
76-100 (23.2-30.4)
16
16
16
16
16
16
12
12
12
12
12
12
12
12
101-125 (30.8-38.1)
16
14
16
16
14
14
12
12
12
10
10
10
10
10
126-150 (38.4-45.7)
16
14
16
14
14
14
10
12
10
10
10
10
10
10
Drycooler Types Without Pump Controls
(D)DNL
(D)DNT
Number of Fans
Control Wire
Run, ft (m)
1-4
6&8
1
2
3
4
6
8
0-25 (0-7.6)
16
16
16
16
16
16
16
16
26-50 (7.9-15.2)
16
16
16
16
16
16
16
16
51-75 (15.5-22.8)
16
16
16
16
16
16
16
14
76-100 (23.2-30.4)
16
16
16
16
16
16
16
12
101-125 (30.8-38.1)
16
16
16
16
16
16
14
12
126-150 (38.4-45.7)
16
16
16
16
16
14
14
10
Data based on 16 AWG min. wire size, 0.4 Amp per contactor, 1 to 1.5 Volt maximum drop & 104 °F (40 °C) average ambient temperature
Table 50
Minimum recommended control circuit wire size, mm2, 50Hz models
Drycooler Types With Pump Controls
DSF
Control Wire
Run, m (ft)
DDF
DSO
DDO
Number of Fans
1
1
1
2
3
4
6
8
1
2
3
4
6
8
0-7.6 (0-25)
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.5
1.0
1.5
1.5
1.5
1.5
1.5
7.9-15.2 (26-50)
1.0
1.0
1.0
1.0
1.0
1.0
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
15.5-22.8 (51-75)
1.0
1.5
1.0
1.5
1.5
1.5
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
23.2-30.4 (76-100)
1.0
2.5
1.0
1.5
2.5
2.5
4.0
6.0
4.0
6.0
6.0
6.0
6.0
6.0
30.8-38.1 (101-125)
1.5
2.5
1.5
2.5
2.5
2.5
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
38.4-45.7 (126-150)
1.5
4.0
1.5
2.5
4.0
4.0
6.0
6.0
6.0
6.0
6.0
10.0
6.0
6.0
Drycooler Types Without Pump Controls
(D)DNL
Control Wire
Run, m (ft)
(D)DNT
Number of Fans
1-4
6&8
1
2
3
4
6
8
0-7.6 (0-25)
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
7.9-15.2 (26-50)
1.0
1.0
1.0
1.0
1.0
1.0
1.0
2.5
15.5-22.8 (51-75)
1.0
1.0
1.0
1.0
1.0
1.5
1.5
4.0
23.2-30.4 (76-100)
1.0
1.0
1.0
1.0
1.0
1.5
2.5
4.0
30.8-38.1 (101-125)
1.0
1.5
1.0
1.5
1.5
2.5
2.5
6.0
38.4-45.7 (126-150)
1.0
1.5
1.0
1.5
1.5
2.5
4.0
6.0
Table based on 1.0 mm2 min. wire size, 0.5 Amp per contactor, 1 to 1.5 Volt maximum drop & 40 °C (104 °F) average ambient temperature
118
Heat Rejection
6.13
Filling Instructions
6.13.1 Preparing the System for Filling
It is important to remove any dirt, oil or metal filings that may contaminate the cooling system piping
in order to prevent contamination of the fresh glycol solution and fouling of the drycooler piping. The
system should be flushed thoroughly using a mild cleaning solution or high-quality water and then
completely drained before charging with glycol. Cleaning new systems is just as important as cleaning old ones. New systems can be coated with oil or a protective film; dirt and scale are also common.
Any residual contaminants could adversely affect the heat transfer stability and performance of your
system. In many cases, in both old and new systems, special cleaners are needed to remove scale, rust
and hydrocarbon foulants from pipes, manifolds and passages. Clean heat transfer surfaces are
important in maintaining the integrity of the heating/cooling system. For more information on cleaners and degreasers, contact your sales representative. Follow the manufacturer’s instructions when
using these products.
Calculate the internal volume of the system as closely as possible. The drycooler volumes are shown
in Table 46. Use Table 52 for field-installed piping volumes. Indoor unit volumes are found in their
user manuals.
6.13.2 Glycol Solutions
NOTE
Glycol solutions should be considered for the protection of the coil. When glycol solutions are
not used, damage can occur either from freezing or from corrosion from water.
When considering the use of any glycol products in a particular application, you should review the
latest Material Safety Data Sheets and ensure that the use you intend can be accomplished safely.
For Material Safety Data Sheets and other product safety information, contact the supplier nearest
you. Before handling any other products mentioned in the text, you should obtain available product
safety information and take necessary steps to ensure safety of use.
NOTICE
Risk of mishandled glycol products. Can cause environmental damage.
When mishandled, glycol products pose a threat to the environment. Before using any glycol
products, review the latest Material Safety Data Sheets and ensure that you can use the
product safely. Glycol manufacturers request that the customer read, understand and comply
with the information on the product packaging and in the current Material Safety Data
Sheets. Make this information available to anyone responsible for operation, maintenance
and repair of the drycooler and related equipment.
No chemical should be used as or in a food, drug, medical device, or cosmetic, or in a product or
process in which it may contact a food, drug, medical device, or cosmetic until the user has
determined the suitability and legality of the use. Since government regulations and use conditions
are subject to change, it is the user's responsibility to determine that this information is appropriate
and suitable under current, applicable laws and regulations.
NOTICE
Risk of using the wrong type of glycol. Can cause piping damage, coolant fluid leaks, and
substantial building damage.
Automotive antifreeze is unacceptable and must NOT be used.
Typical inhibited formula ethylene glycol and propylene glycol manufacturers and suppliers are
Union Carbide (Ucartherm) and Dow Chemical (Dowtherm SR-1, Dowfrost). These glycols are
supplied with corrosion inhibitors and do not contain a silicone anti-leak formula. Commercial
ethylene glycol and propylene glycol, when pure, are generally less corrosive to the common metals of
construction than water itself. Aqueous solutions of these glycols, however, assume the corrosivity of
the water from which they are prepared and may become increasingly corrosive with use when not
properly inhibited.
119
Heat Rejection
There are two basic types of additives:
• Corrosion inhibitors and
• Environmental stabilizers
The corrosion inhibitors function by forming a surface barrier that protects the metals from attack.
Environmental stabilizers, while not corrosion inhibitors in the strictest sense of the word, decrease
corrosion by stabilizing or favorably altering the overall environment. An alkaline buffer, such as
borax, is a simple example of an environmental stabilizer, since its prime purpose is to maintain an
alkaline condition (pH above 7).
The percentage of glycol to water must be determined by using the lowest design outdoor temperature
in which the system is operating. Table 51 indicates the solution volume of inhibited glycol required
to provide freeze protection at various ambient temperatures.
Table 51
Glycol concentrations for freeze protection by ambient temperatures
Temperature, °F (°C
20 (-7)
10 (-12)
0 (-18)
-10 (-23)
-20 (-29)
-30 (-34)
-40 (-40)
-50 (-46)
Propylene Glycol
% by Volume
18 *
29*
36
42
46
50
54
57
Ethylene Glycol
% by Volume
17 *
26*
35
41
46
50
55
59
Coolant Type
Based on Dowfrost™ (PG) and Dowtherm™ SR-1 (EG) product literature.
* Inhibitor levels should be adjusted to properly protect the system if solution concentrations are less than 30%.
NOTICE
Risk of corrosive dilution water. Can cause piping system damage, coolant fluid leaks and
substantial building damage.
The quality of water used for dilution must be considered because water may contain
corrosive elements that reduce the effectiveness of the inhibited formulation. Surface water
that is classified as soft (low in chloride and sulfate ion content—less than 100 ppm each)
should be used.
120
Heat Rejection
6.13.3 Filling the System
Installation of hose bibs at the lowest point of the system is recommended.
When filling a glycol system keep air to a minimum. Air in glycol turns to foam and is difficult and
time-consuming to remove. (Anti-foam additives are available and may be considered.)
Open all operating systems to the loop. With the top vent(s) open, fill the system from the bottom of
the loop. This will allow the glycol to push the air out of the top of the system, minimizing trapped air.
Fill to approximately 80% of calculated capacity. Fill slowly from this point, checking fluid levels until
full.
NOTE
For glycol solution preparation and periodic testing, follow manufacturer’s recommendations.
Do not mix products of different manufacturers.
Table 52
Volume in standard Type "L" copper piping
Diameter (in.)
6.14
Volume
Outside
Inside
gal/ft
l/m
1-3/8
1.265
0.065
0.81
1-5/8
1.505
0.092
1.15
2-1/8
1.985
0.161
2.00
2-5/8
2.465
0.248
3.08
3-1/8
2.945
0.354
4.40
3-5/8
3.425
0.479
5.95
4-1/8
3.905
0.622
7.73
Outdoor Control Enclosure
The Liebert Outdoor Control Enclosure is designed to be used with a Liebert condenser or drycooler to
control one or more pump and/or fan motors. The enclosure is rated NEMA 3R when installed as
shown in Figure 114.
Figure 114Liebert Outdoor Control Enclosure installed
121
Heat Rejection
Figure 115 Flow rate, 10 hp, 3500 rpm pump package, Model # 9A31258G3 in aluminum enclosure
200
C
180
Total Head (Ft of Water)
160
140
120
100
Ensure that the tank included in the design
has a minimum volume of 6% of the total
system volume.
80
60
40
20
0
0
100
200
300
400
500
Flow Rate (GPM)
Table 53
SAFM-7820-11
Rev. 2
Liebert Outdoor Control Enclosure specifications
Connections
Model
D10ANTS1317
D10ANTS1317
HP
Size
Impeller
Discharge
Suction
10
2 x 1.5 x 7
6.44
1.5 FPT
2.0 FPT
122
Cabinet Size- in (mm)
FLA
Length
Width
Height
14
41.3
(1049)
32.4
(822)
19.9
(506)
30.8
Heat Rejection
6.14.1 Electrical Connections
WARNING
Risk of electric shock. Can cause injury or death.
Disconnect all local and remote power supplies before working within.
6.14.2 Hazardous Voltage Power Supply Wiring
Wire per national and local electrical codes.
Hazardous voltage electrical service is required at the location of the control enclosure. Use the
knockouts provided at the bottom of the enclosure. This power supply does not have to be the same
voltage as the Liebert indoor unit. This separate power source may be 110V, 208V, 230V, 460V or
575V, single-phase or three-phase, 60Hz; or it may be 200V, 230V, 380V or 415V, single-phase or
three-phase, 50Hz as appropriate.
Install a field-supplied disconnect as required per local and national codes.
Figure 116Dimensions and knockout sizes, 36-inch models
7-9/16"
(192mm)
36"
914.4
A
20-5/16"
(515.9mm)
2-13/16"
(71.4mm)
16-13/16"
(427mm)
1-7/16"
(36.5mm)
3-11/16"
(93.7mm)
A
2-5/8"
Knockouts
(66.7mm)
7/8" (.875mm)
1-1/8" (28.6mm)
1-3/8" (34.9mm)
1-3/4" (44.45mm)
3"
2-3/4"
(76.2mm)
(69.9mm)
9-9/16"
(242.9mm)
4"
(101.6mm)
11-1/8"
(282.6mm)
1-15/16" (49.2mm)
7/8" (.875mm)
Knockout
37-9/16"
(954mm)
Knockouts
7/8" (.875mm)
1-1/8" (28.6mm)
1-3/8" (34.9mm)
123
VIEW A-A
1-1/8"
(28.6mm)
Knockout
7/8" (.875mm)
Knockout
SL-10074
Heat Rejection
6.14.3 Extra-Low Voltage Control Wiring
Control interlock between the control enclosure and the indoor unit(s) or other source(s) is required.
Multiple indoor units may be connected in parallel if the controlled pumps will feed them all.
• Extra-low voltage, non-safety control wiring must be a minimum of 16 GA. (1.665 mm2) for up to
75 feet (22.9m), or not to exceed 1V drop in the control line.
• Install extra-low voltage control wiring (24V) from Terminals 70 & 71 on the wire raceway in the
compressor compartment of the indoor unit to Terminals 70 & 71 of the control enclosure.
• Extra-low voltage control wiring should also be installed between Terminals 24 and 50 from the
control enclosure to the indoor cooling unit’s common alarm or other alarm location for loss-offlow indication.
• Install extra-low voltage control wiring between the auxiliary terminals on the control panel to
Terminals 70 and 71 on the drycooler.
• The flow switch wiring should be connected to Terminals 77 and 74.
• Provide line voltage to power block(s) in control enclosure as shown in the electrical schematic.
• Install optional field-supplied disconnect if desired.
• Run three-phase line voltage from the control box to each individual pump motor.
6.14.4 Dual Pump Package Flow Switch
Mount the flow switch in a section of coolant supply/return piping where there is a straight run of at
least five (5) pipe diameters on each side of the flow switch.
• The switch should be mounted so the terminals or wire leads are easily accessible for wiring.
• Mount the flow switch in a standard 1" x 1" x 1" tee for one-inch pipe installation. Use a reducing
tee for larger sizes of pipe to keep the flow switch near the pipe and to provide adequate paddle
length in the flow stream.
• Screw the flow switch in position so the flat part of the paddle is at a right angle to the flow. The
arrow on the side of the case must point in the direction of the flow.
• The flow switch must be mounted in a horizontal pipeline.
6.14.5 Dual Pump Controls Sequence of Operation
On a call for cooling, the compressor contactor and/or the Econ-O-Coil relay in the Liebert unit is
energized. The relay and contactor are in the Liebert indoor evaporator section. Each compressor
contactor has a side switch wired in parallel with the Econ-O-Coil relay and is responsible for closure
of the low-voltage pump-control circuit.
This low-voltage circuit has a series of contactors, relays, selector switch and a flow switch. This
circuit controls the start of the pumps and provides contact closure to interlock the drycooler(s)
control circuit. Once the circuit is closed, 24V is passed to the pumps control circuit and the auxiliary
relays are energized, closing the drycooler(s) control circuit.
Pump P1 is factory-set to be the primary pump (Selector Switch 1-2). Voltage then passes through the
normally closed contacts of the R2 relay (standby pump relay), through the current overloads and to
the #1 pump contactor. At this point, the #1 pump and appropriate drycoolers are running.
When the pump establishes flow, it opens the system flow switch. The pump has approximately
10 seconds to establish full flow. If it does, the system will run in this state until the call for cooling is
satisfied and the circuit drops out. If this pump cannot establish flow or if it has been running and
fails, the flow switch will close and energize an adjustable relay, typically set for 10 seconds.
Once this relay times out, it energizes the R2 switch over relay. This relay will drop out the voltage to
the #1 pump contactor and energize the #2 pump contactor. Along with the R2 relay the AL relay
(alarm relay) will energize. This will provide a set of closed contacts for remote indication of the
switch-over situation.
Once the problem with the lead pump is repaired, the controls must be reset. To reset the control box,
turn Off the main power to the control box and then restore the main power to the control box. Pump
P1 then becomes the primary pump again.
124
Liebert iCOM
7.0
LIEBERT ICOM
Figure 117 Liebert iCOM display—Liebert XDC and Liebert XDP
Liebert iCOM display—Liebert XDP
Liebert iCOM display—Liebert XDC
7.1
Liebert iCOM Display Layout
The Liebert iCOM displays icons and text for monitoring and controlling your Liebert cooling unit.
Figures 105 and 106 shows the Liebert iCOM's home screen for the Liebert XDC and Liebert XDP.
Figure 118 Liebert iCOM default home screen for Liebert XDC
Unit
Name
Sensor A
Room Data
Sensor B
Room Data
Pump Operation shown by
animated refrigerant lines
UNIT 1
Liebert XDC
57°F
50.0°F set
CFC: 15%
Sensor
Temp
Hum
Dew Pt
Date and Time
Alarm/Event
History
Navigation
Prompts
A
63°F
42%
39°F
Refrigerant
Temperature
Available only
with Liebert XD
Smart Modules
B
71°F
29%
38°F
08/2012
8/27/2011 15:03
UNIT ON
8/27/2011 14:07(01) MSG POWER ON
8/27/2011 14:07(01) MSG POWER OFF
for nex t /pr ev i ous uni t
for s y s tem v i ew
for menu ; E S C for pr ev s c r een ; ? for hel p
125
Next Scheduled
Maintenance
Unit
Status
Liebert iCOM
Figure 119 Liebert iCOM default home screen for Liebert XDP
Sensor A
Room Data
Unit
Name
Sensor B
Room Data
Pump Operation
represented by animated
refrigerant lines
UNIT 1
Liebert
57°F
50.0°F set
XDP
CFC: 30%
Sensor
A
B
Temp: 74°F 72°F
Hum:
50% 50%
Dew Pt: 55°F 54°F
Date and
Time
Alarm/Event
History
Navigation
Prompts
7.2
Available only
with Liebert XD
Smart Modules
28.02.2012 15 :03
28.02.2012 14:07 (01) UNIT ON
28.02.2012 14:07 (01) UNIT ON
pr es s :
pr es s :
Refrigerant
Temperature
08/2011
Next Scheduled
Maintenance
UNIT ON
Unit Status
for nex t /pr ev uni t
for uni t /s y s tem v i ew
for menu ; ESC for pr ev s c r een ; ? for hel p
Cooling Module Overview
The Liebert iCOM will display an overview of all connected cooling modules. It does not display a
system view, which would include units other than the cooling modules (Figure 120). The Liebert
iCOM will also display smart module parameters (Figure 121).
Figure 120 Cooling module overview
UNIT 1
Liebert XDP Max XD Supply 212°F 100% OFF
Air Temp
°F
70
72
74
76
75
73
74
71
77
9/2013
72
AA01 AA01 AA01 AA01 AA01 AA01 AA01 AA01 AA01AA01
8/4/2012 14 :13:54
ALARM OFF
(01) 8/2/2012 08 :33 RST General Alarm
(01) 8/2/2012 08 :20 ACK HIGH CHILLED WATER TEMP
for system view
for next/previous unit
ESC
for menu
for previous screen
? for help
126
Liebert iCOM
Figure 121 Smart module parameters—Liebert XDH, Liebert XDO, Liebert XDV
MODULE STATUS (page 1 of 20)
UNIT 01
U901 NODE 82 AA82
57°F
U902
U903
98°F
U904
U905
XDH
U906
TOP/
98°F
U907
BOTTOM
U908
U909
U910
XDH32SK
U911 Model / Capacity
ON
U912 Middle Fan Status
ON
U913 Top and Bottom Fan Status
ONLINE
Liebert XDH
Each Bank
Shown
Separately
73°F
15
KW
Liebert XDO
MODULE STATUS (page 1 of 20)
U901 NODE 81 AF01
U902
57°F
U903
U904
U905
U906
U907
92°F
U908
U909
U910
U911 Model / Capacity
U912 Fan Status
U913
UNIT 01
ONLINE
XDO
92°F
68°F
XDO20SK
ON
20
KW
Liebert XDV
MODULE STATUS (page 1 of 20)
U901 NODE 81 AZ81
U902
57°F
U903
U904
U905 92°F
U906
U907
U908
U909
U910
U911 Model / Capacity
U912 Left Fan Status
U913 Right Fan Status
UNIT 01
ONLINE
XDV
66°F 65°F
XDV8SK
ON
ON
127
8
KW
Liebert iCOM
7.3
Graphical Data Record
The Graphical Data Record charts the average temperature from Sensors A and B, the average dew
point from Sensors A and B, the supply refrigerant temperature and the supply refrigerant control
point.
The temperature scales can be changed to expand or compress the data.
The time scale also can be altered to any of several selectable values.
7.3.1
Liebert iCOM User Menu Icons and Legend
User menus report general cooling unit operations and status. User Menu screens employ a coding
that begins in “U” and is followed by parameters and information, such as settings.
Figure 122 Liebert iCOM User Menu icons
°C / °F
% RH
SET
Setpoints
View and change
operational
setpoints
EVENT
LOG
Spare Parts List
Contains spare
parts available on
site
Event Log
Lists last 400
events and
alarms
View Only
!
ACTIVE
ALARMS
Sensor Data
Shows readings
of sensors; View
Only
Active Alarms
Lists all current
alarms; View Only
SET
ALARMS
Graphic Data Record
Displays average
temperature from
Sensors A and B, the
average dew point from
Sensors A and B, the
supply refrigerant
temperature and the
supply refrigerant control
point graphs; Data is
View Only;
Display scale is
adjustable
View Network
Shows status of
all connected
units; View Only
1234h
XDIO
Total Run Hours
Records the run time of
all components and
allows setting of limits on
run time; View Only
XDIO
Displays
readings for the
individual smart
modules; View
Only
Set Alarms
Allows user to
change settings for
alarms
12
9
SET
3
6
Display Setup
Change settings
for display:
language and
time
128
Service
Contacts
Contains key
contact information
for service
Liebert iCOM
7.3.2
Liebert iCOM Service Menu Icons and Legend
Service menus allow customized settings for site operations. Service Menu screens employ a
codingthat begins in “S” and is followed by parameters and information, such as settings.
Figure 123 Liebert iCOM Service Menu icons
°C / °F
% RH
SET
SET
ALARMS
WELLNESS
Setpoints
View and change
operational
setpoints
Maintenance/
Wellness
Settings
Shows all maintenance records, calculates next
maintenance date
Unit Diary
Shows all program
changes and
maintenance
performed,
NETWORK
SET
UP
+/Sensor
Calibration/Setup
Setup and calibrate
sensors for site
7.4
Network
Setup or alter
network setting.
Options Setup
Enter specific
settings for various
options
SERVICE
Set Alarms
Diagnostics/
Change settings for
Service Mode
alarms
Enter Diagnostics/
Service Mode for
troubleshooting
and repair
XDIO
Smart Module
Setup of alarms
and events. Set
temperature limits
for supply and
return sensors.
Label smart
modules, view
firmware version.
Service Contacts
Contains key
contact information
for service
Liebert XDC Alarms Descriptions
NOTE
Alarms must be acknowledged before they can be reset. To acknowledge or silence an alarm,
press the ALARM key one time. This will silence the alarm; the red LED will remain
illuminated until the alarm is reset.
• CALL SERVICE—Activated when Customer Input 1 is configured for “Call Service” and 24VAC
is applied to the input. This alarm is reset when the 24VAC is removed.
• COMP 1A HIGH PRESSURE—Activated when the control senses a high head pressure signal
from Compressor 1A . This alarm will reset when the main power is cycled or the HP 1A Alarm
Code variable in the Service Diagnostics menu is reset to 0.
• COMP 1B HIGH PRESSURE—Activated when the control senses a high head pressure signal
from Compressor 1B. This alarm will reset when the main power is cycled or the HP 1B Alarm
Code variable in the Service Diagnostics menu is reset to 0.
• COMP 2A HIGH PRESSURE—Activated when the control senses a high head pressure signal
from Compressor 2A. This alarm will reset when the control power is cycled or the HP 2A Alarm
Code variable in the Service Diagnostics menu is reset to 0.
• COMP 2B HIGH PRESSURE—Activated when the control senses a high head pressure signal
from Compressor 2B by the control. This alarm will reset when the main power is cycled or the
HP 2B Alarm Code variable in the Service Diagnostics menu is reset to 0.
• COMP 1A SHORT CYCLE—Activated when Compressor 1A turns On, Off, then back On, 10
times within 1 hour. The alarm will reset itself when the control turns Compressor 1A On, then
Off fewer than 10 times within 1 hour of operating time for 1.5 hours.
129
Liebert iCOM
• COMP 1B SHORT CYCLE—Activated when Compressor 1B turns On, Off, then back On, 10
times within 1 hour. The alarm will reset itself when the control turns Compressor 1B On, then
Off fewer than 10 times within 1 hour of operating time for 1.5 hours.
• COMP 2A SHORT CYCLE—Activated when Compressor 2A turns On, Off, then back On, five
times within 10 minutes or 10 times within 1 hour. The alarm will reset itself when the control
turns Compressor 2A On, then Off fewer than 10 times within 1 hour of operating time for 1.5
hours.
• COMP 2B SHORT CYCLE—Activated when Compressor 2B turns On, Off, then back On, five
times within 10 minutes or 10 times within 1 hour. The alarm will reset itself when the control
turns Compressor 2B On, then Off fewer than 10 times within 1 hour of operating time for 1.5
hours.
• COMPRESSOR(S) LOCKOUT—Activated when Customer Input 1 is configured for “Comp
Lock PD” and 24VAC is applied to the input. This alarm is reset when the 24VAC is removed.
• CONDENSATION DETECTED (optional)—Activated when water is detected at a cooling
module. A 24VAC signal is applied to the condensation input on the control board using a twisted
pair of wires or the alarm is sent via CANbus communication. When this alarm is active, the
control will raise its refrigerant control point by 4°F (2.2°C). This alarm will reset when the
alarms is acknowledged and the signal stops being sent from CANbus or condensation input. The
alarm can also be reset by cycling the power. The main power must be cycled to remove the 4°F
(2.2°C) offset.
• CUSTOMER INPUT 1—Activated when a 24VAC signal is applied to the customer alarm input
on the control board. This alarm will reset when the 24VAC signal stops being sent from the
customer alarm input. WATER UNDER FLOOR, SMOKE DETECTED, CALL SERVICE and
COMP LOCK PD are possible designations for this alarm; they are set with the Unit Code.
• FAN FAILURE (optional)—Activated when a 24VAC signal is applied to the fan failure input on
the control board using a twisted pair of wires or the alarm is sent via CANbus communication.
This alarm will reset when the alarms is acknowledged and the signal stops being sent from
CANbus or fan failure input. The alarm can also be reset by cycling the power.
• HIGH DEW POINT—Activates when the calculated dew point at either Sensor A or B exceeds
the user-specified alaram setpoint. The alarm will reset when the calculated room dew point from
both Sensor A and Sensor B is 2°F (1.1°C) below the setpoint and the alarm has been
acknowledged.
• HIGH REFRIGERANT TEMP—Activated when the refrigerant temperature sensor reads the
refrigerant temperature above the user-specified alarm setpoint. This alarm will reset when the
reading from the refrigerant temperature sensor drops 2°F (1.1°C) below the user-specified
setpoint and the alarm has been acknowledged.
• HIGH TEMP SENSOR A—Activated when the reading from Sensor A is above the userspecified alarm setpoint. The alarm will reset when the reading from Sensor A drops 2°F (1.1°C)
below the setpoint and the alarm has been acknowledged.
• HIGH TEMP SENSOR B—Activated when the reading from Sensor B is above the userspecified alarm setpoint. The alarm will reset when the reading from Sensor B drops 2°F (1.1°C)
below the setpoint and the alarm has been acknowledged.
• LOSS OF FLOW PUMP 1—Activated when Pump 1 is commanded to run and the differential
pressure switch does not sense differential pressure (set at 6 psi; 41kPa; 0.41 bars). After
attempting to start Pump 1 three times, the Liebert XDC will automatically switch to the other
pump to establish flow. This alarm will reset when flow has been established on Pump 1 and the
alarm has been acknowledged.
• LOSS OF FLOW PUMP 2—Activated when Pump 2 is commanded to run and the differential
pressure switch does not sense differential pressure (set at 6 psi; 41kPa; 0.41 bars). After
attempting to start Pump 2 three times, the Liebert XDC will automatically switch to the other
pump to establish flow. This alarm will reset when flow has been established on Pump 2 and the
alarm has been acknowledged.
• LOW MEMORY—Activated when the control board is low in memory resources. This alarm rests
automatically as soon as memory consumption falls below the threshold.
130
Liebert iCOM
• LOW REFRIGERANT TEMP—Activated when the supply refrigerant temperature sensor
temperature reading drops below the higher of the two calculated dew points, assuming that
neither Sensor A or Sensor B has a sensor failure alarm. This alarm will reset when the
refrigerant temperature sensor reads the refrigerant temperature above both of the two
calculated dew points and the alarm has been acknowledged. This alarm can lock the unit Off. If
this occurs, the main power must be cycled, or the Low Refrig Temp Alarm Code in the Service
Diagnostics menu must be reset to 0.
• LOW TEMP SENSOR A—Activates when the reading from Sensor A drops below the userspecified alarm setpoint. The alarm will reset when the reading from Sensor A rises 2°F (1.1°C)
above the setpoint and the alarm has been acknowledged.
• LOW TEMP SENSOR B—Activates when the reading from Sensor B drops below the userspecified alarm setpoint. The alarm will reset when the reading from Sensor B rises 2°F (1.1°C)
above the setpoint and the alarm has been acknowledged.
• NODEX CONDENSATION DETEC—Activated when condensation is detected on a smart
module at CAN node ID X, where X is a value ranging from 81 to 100. This alarm resets when
condensate is no longer detected. The main power must be cycled off to remove the 4°F (2.2°C)
offset value.
• NODEX FAN FAILURE—Activated when a fan failure occurs on a smart module at CAN node
ID X, where X is a value ranging from 81 to 100. The alarm will rest when the fan returns to
normal operation.
• NODEX LOCAL SHUT DOWN—Activated when a smart module at CAN node ID X, where X is
a value ranging from 81 to 100, has been shut down by an external signal. This alarm will reset
when the remote shutdown input is deactivated.
• NODEX RETURNAIR TEMPLIMT—Activated when the return air temperature (entering air
temperature to the module) exceeds the user-specified return air temperature range on a smart
module at CAN node ID X, where X is a value ranging from 81 to 100. This alarm will reset when
the return air temperature return to with the user-specified range.
• NODEX SENSOR FAILURE—Activated when a smart module at CAN node ID X, where X is a
value ranging from 81 to 100, stops receiving a signal from one or more of its supply air, return
air, or refrigerant temperature sensors. This alarm will reset when signals are detected from the
module's sensors.
• NODEX SUPPLYAIR TEMPLIMT—Activated when the supply air temperature (temperature
of the air leaving the module) exceeds the user-specified supply air temperature range on a smart
module at CAN node ID X, where X is a value ranging from 81 to 100. This alarm will reset when
the return air temperature return to with the user-specified range.
• PUMP SHORT CYCLE—Activated when the Liebert XDC is trying to establish flow
(differential pressure) and is unable to do so. The Liebert XDC will attempt three times to
establish flow on a pump before trying the other pump. The control will keep cycling three times
on one pump, then three times on the other pump until it is able to establish flow (differential
pressure). If this cycling occurs for 30 minutes and the Liebert XDC still does not establish flow, a
PUMP SHORT CYCLE alarm will be present. This alarm will shut down the Liebert XDC. To
reset this alarm, the main power must be cycled.
• RAM/BATTERY FAIL—Activated when the RAM backup battery or the RAM itself has failed.
This requires a hardware replacement.
• SENSOR A FAILURE—Activated when the controls no longer senses a signal from Sensor A.
This alarm will reset when the signal is returned and the alarms has been acknowledged.
• SENSOR B FAILURE— Activated when the controls no longer senses a signal from Sensor B.
This alarm will reset when the signal is returned and the alarm has been acknowledged.
• SMOKE DETECTED—Activated when the Customer Input 1 is configured for “Smoke” and
24VAC is applied to the input. This alarm is reset when the 24VAC is removed.
NOTE
This is not a room smoke detector and is not intended to replace external smoke detectors.
• SUPPLY REFRIGERANT SENSOR FAILURE—Activated when the control no longer senses
a signal from the supply refrigerant sensor. This alarm will reset when the signal is returned.
131
Liebert iCOM
• TANDEM BANK 1 LP—Activated when the low-pressure switch for Tandem Compressor
Bank 1 doesn't send the proper signal during normal operation, or during pump-down. This alarm
will reset when the main power is cycled or the Tandem Bank 1 LP Code variable in the Service
Diagnostics menu is reset to 0.
• TANDEM BANK 2 LP—Activated when the low-pressure switch for Tandem Compressor
Bank 2 doesn't send the proper signal during normal operation, or during pump-down. This alarm
will reset when the main power is cycled or the Tandem Bank 2 LP Code variable in the Service
Diagnostics menu is reset to 0.
• TANDEM BANK 1 PD—Activated when Tandem Compressor Bank 1 suction pressure cannot
be pumped down below the threshold during compressor shutdown. This alarm will reset when
the main power is cycled or the Tandem Bank 1 PD Alarm Code variable in the Service
Diagnostics menu is reset to 0.
• TANDEM BANK 2 PD—Activated when Tandem Compressor Bank 2 suction pressure cannot be
pumped down below the threshold during compressor shutdown. This alarm will reset when the
main power is cycled or the Tandem Bank 2 PD Alarm Code variable in the Service Diagnostics
menu is reset to 0.
• UNIT CODE MISSING—Activated when a valid unit code has not been entered and saved. To
reset, enter valid unit code, save and execute.
• WATER UNDER FLOOR—Activated when Customer Input 1 is configured for “Water Alarm”
and 24VAC is applied to the input. This alarm is reset when the 24VAC is removed.
7.5
Warning Descriptions
• COMPRESSOR 1A HRS EXCEED—Activated when the Compressor 1A Actual Hours exceeds
the user-specified limit. To reset, Actual Hours must be reset to 0.
• COMPRESSOR 1B HRS EXCEED—Activated when the Compressor 1B Actual Hours exceeds
the user-specified limit. To reset, Actual Hours must be reset to 0.
• COMPRESSOR 2A HRS EXCEED—Activated when the Compressor 2A Actual Hours exceeds
the user-specified limit. To reset, Actual Hours must be reset to 0.
• COMPRESSOR 2B HRS EXCEED—Activated when the Compressor 2B Actual Hours exceeds
the user-specified limit. To reset, Actual Hours must be reset to 0.
• PUMP 1 HRS EXCEED—Activated when the Pump 1 Actual Hours exceeds the user-specified
limit. To reset, Actual Hours must be reset to 0.
• PUMP 2 HRS EXCEED—Activated when the Pump 2 Actual Hours exceeds the user-specified
limit. To reset, Actual Hours must be reset to 0.
• LOSS OF POWER—Activated when the unit is On and operational and 24VAC power to the
control is lost. This alarm will be emitted when power is restored to the control. The Liebert XDC
will restart at a user-defined time delay after power is restored. Once activated, the alarm will
remain activated for 30 minutes.
132
Liebert iCOM
7.6
Liebert XDP Alarms
NOTE
Alarms must be acknowledged before they can be reset. To acknowledge or silence an alarm,
press the ALARM key one time. This will silence the alarm; the red LED will remain
illuminated until the alarm is reset.
CALL SERVICE—Activated when Customer Input 1 is configured for “Call Service” and 24VAC is
applied to the input. This alarm is reset when the 24VAC is removed.
CONDENSATION DETECTED (optional)—Activated when water is detected at a cooling module.
A 24VAC signal is applied to the condensation input on the control board using a pair of twisted wires
or the alarm is sent via CANbus communication. When this alarm is active, the control will raise its
refrigerant control point by 4°F (2.2°C). This alarm will reset when the alarms is acknowledged and
the signal stops being sent from CANbus or condensation input. The alarm can also be reset by
cycling the power. The main power must be cycled to remove the 4°F (2.2°C) offset.
CONTROL VALVE FAILURE—Activated when the chilled water control valve has been
commanded to open or close by the control and no change is detected by the valve position signal. The
alarm is reset when the main power is cycled.
CUSTOMER INPUT 1—Activated when a 24VAC signal is applied to the customer alarm input on
the control board. This alarm will reset when the 24VAC signal stops being sent from the customer
alarm input. WATER UNDER FLOOR, SMOKE DETECTED, CALL SERVICE, and COMP LOCK
PD are possible designations for this alarm; they are set with the Unit Code.
FAN FAILURE (optional)—Activated when a 24VAC signal is applied to the fan failure input on
the control board using a twisted pair of wires or the alarm is sent via CANbus communication. This
alarm will reset when the alarms is acknowledged and the signal stops being sent from CANbus or
fan failure input. The alarm can also be reset by cycling the power.
HIGH CW TEMP—Activated when the Supply CW sensor reads the chilled water temperature
above the user-specified alarm setpoint. This alarm will reset when the reading from the refrigerant
temperature sensor drops 5°F (2.8°C) below the user-specified setpoint and the alarm has been
acknowledged.
HIGH DEW POINT—Activates when the calculated dew point at either Sensor A or B exceeds the
user-specified alarm setpoint. The alarm will reset when the calculated room dew point from both
Sensor A and Sensor B is 2°F (1.1°C) below the setpoint and the alarm has been acknowledged.
HIGH REFRIGERANT TEMP—Activated when the refrigerant temperature sensor reads the
refrigerant temperature above the user-specified alarm setpoint. This alarm will reset when the
reading from the refrigerant temperature sensor drops 2°F (1.1°C) below the user-specified setpoint
and the alarm has been acknowledged.
HIGH TEMP SENSOR A—Activated when the reading from Sensor A is above the user-specified
alarm setpoint. The alarm will reset when the reading from Sensor A drops 2°F (1.1°C) below the
setpoint and the alarm has been acknowledged.
HIGH TEMP SENSOR B—Activated when the reading from Sensor A is above the user-specified
alarm setpoint. The alarm will reset when the reading from Sensor A drops 2°F (1.1°C) below the
setpoint and the alarm has been acknowledged.
LOSS OF FLOW PUMP 1—Activated when Pump 1 is commanded to run and the differential
pressure switch does not sense differential pressure (set at 6 psi; 41kPa; 0.41 bars). After attempting
to start Pump 1 three times, the Liebert XDP will automatically switch to the other pump to establish
flow. This alarm will reset when flow has been established on Pump 1 and the alarm has been
acknowledged.
LOSS OF FLOW PUMP 2—Activated when Pump 2 is commanded to run and the differential
pressure switch does not sense differential pressure (set at 6 psi; 41kPa; 0.41 bars). After attempting
to start Pump 2 three times, the Liebert XDP will automatically switch to the other pump to establish
flow. This alarm will reset when flow has been established on Pump 2 and the alarm has been
acknowledged.
LOW MEMORY—Activated when the control board is low in memory resources. This alarm rests
automatically as soon as memory consumption falls below the threshold.
133
Liebert iCOM
LOW REFRIGERANT TEMP—Activated when the supply refrigerant temperature sensor
temperature reading drops below the higher of the two calculated dew points, assuming that neither
Sensor A or Sensor B has a sensor failure alarm. This alarm will reset when the refrigerant
temperature sensor reads the refrigerant temperature above both of the two calculated dew points
and the alarm has been acknowledged. This alarm can lock the unit Off. If this occurs, the main
power must be cycled, or the Low Refrig Temp Alarm Code in the Service Diagnostics menu must be
reset to 0.
LOW TEMP SENSOR A—Activated when the reading from Sensor A drops below the user-specified
alarm setpoint. The alarm will reset when the reading from Sensor A rises 2°F (1.1°C) above the
setpoint and the alarm has been acknowledged.
LOW TEMP SENSOR B—Activated when the reading from Sensor B drops below the user-specified
alarm setpoint. The alarm will reset when the reading from Sensor B rises 2°F (1.1°C) above the
setpoint and the alarm has been acknowledged.
NODEX CONDENSATION DETEC—Activated when condensation is detected on a smart module
at CAN node ID X, where X is a value ranging from 81 to 100. This alarm resets when condensate is
no longer detected. The main power must be cycled off to remove the 4°F (2.2°C) offset value.
NODEX FAN FAILURE—Activated when a fan failure occurs on a smart module at CAN node ID X,
where X is a value ranging from 81 to 100. The alarm will rest when the fan returns to normal
operation.
NODEX LOCAL SHUT DOWN—Activated when a smart module at CAN node ID X, where X is a
value ranging from 81 to 100, has been shut down by an external signal. This alarm will reset when
the remote shutdown input is deactivated.
NODEX RETURNAIR TEMPLIMT—Activated when the return air temperature (entering air
temperature to the module) exceeds the user-specified return air temperature range on a smart
module at CAN node ID X, where X is a value ranging from 81 to 100. This alarm will reset when the
return air temperature return to with the user-specified range.
NODEX SENSOR FAILURE—Activated when a smart module at CAN node ID X, where X is a
value ranging from 81 to 100, stops receiving a signal from one or more of its supply air, return air, or
refrigerant temperature sensors. This alarm will reset when signals are detected from the module’s
sensors.
NODEX SUPPLYAIR TEMPLIMT—Activated when the supply air temperature (temperature of
the air leaving the module) exceeds the user-specified supply air temperature range on a smart
module at CAN node ID X, where X is a value ranging from 81 to 100. This alarm will reset when the
return air temperature return to with the user-specified range.
PUMP SHORT CYCLE—Activated when the Liebert XDP is trying to establish flow (differential
pressure) and is unable to do so. The Liebert XDP will attempt three times to establish flow on a
pump before trying the other pump. The control will keep cycling three times on one pump, then three
times on the other pump until it is able to establish flow (differential pressure). If this cycling occurs
for 30 minutes and the Liebert XDP still does not establish flow, a PUMP SHORT CYCLE alarm will
be present. This alarm will shut down the Liebert XDP. To reset this alarm, the main power must be
cycled.
RAM/BATTERY FAIL—Activated when the RAM backup battery or the RAM itself has failed. This
requires a hardware replacement.
SENSOR A FAILURE—Activated when the controls no longer senses a signal from Sensor A. This
alarm will reset when the signal is returned and the alarms has been acknowledged.
SENSOR B FAILURE— Activated when the controls no longer senses a signal from Sensor B. This
alarm will reset when the signal is returned and the alarm has been acknowledged.
SMOKE DETECTED—Activated when the Customer Input 1 is configured for “Smoke” and 24VAC
is applied to the input. This alarm is reset when the 24VAC is removed.
NOTE
This is not a room smoke detector and is not intended to replace external smoke detectors.
134
Liebert iCOM
SUPPLY CW SENSOR FAILURE—Activated when the control no longer senses a signal from the
Supply CW sensor. This alarm will reset when the signal is returned.
SUPPLY REFRIGERANT SENSOR FAILURE—Activated when the control no longer senses a
signal from the supply refrigerant sensor. This alarm will reset when the signal is returned.
UNIT CODE MISSING—Activated when a valid unit code has not been entered and saved. To reset,
enter valid unit code, save and execute.
WATER UNDER FLOOR—Activated when Customer Input 1 is configured for “Water Alarm” and
24VAC is applied to the input. This alarm is reset when the 24VAC is removed.
7.7
Liebert XDP Warnings
LOSS OF POWER—Activated when the unit is On and operational and 24VAC power to the control
is lost. This alarm will be emitted when power is restored to the control. The Liebert XDP will restart
at a user-defined time delay after power is restored. Once activated, the alarm will remain activated
for 30 minutes.
PUMP 1 HRS EXCEED—Activated when the Pump 1 Actual Hours exceeds the user-specified limit.
To reset, Actual Hours must be reset to 0.
PUMP 2 HRS EXCEED—Activated when the Pump 2 Actual Hours exceeds the user-specified limit.
To reset, Actual Hours must be reset to 0.
7.8
CANbus Communications
A Controller Area Network (CAN) is a specialized internal communication network. It allows a
Liebert XDP, Liebert XDC and Liebert XD Smart Modules to communicate without a host computer.
Networking the Liebert XDP or Liebert XDC to Smart Modules enables the Smart Modules to be
controlled and monitored from the Liebert XDP or Liebert XDC.
Figure 124 shows a typical Liebert XD system in a CANbus network. Liebert XD Smart Modules
should be connected to the Liebert XDP or Liebert XDC that supplies the modules with refrigerant.
Figure 124 Liebert XD system with CANbus
Remote
Temperature/
Humidity
Sensor A
Remote
Temperature/
Humidity
Sensor B
NOTE
Only six Liebert XDV10S* are shown. A maximum of 16 Liebert XDV10S*, a maximum of 20
Liebert XDV8S*, maximum of eight single-circuited Liebert XDH20S*, five single-circuited
Liebert XDH32S*, maximum of eight Liebert XDO20S*, or a maximum of 10 Liebert XDO16S*
can be connected together on a single CANbus.
135
Liebert iCOM
Plan wiring runs for Unit-to-Module (U2M) communication when designing the layout of the
conditioned space. In addition to general good wiring practices, take into account:
• Keep control and communication cables away from power cables to prevent electromagnetic
interference.
• Do not bend cables to less than four times the diameter of the cable.
• Do not deform cables when securing in bundles or when hanging them.
• Keep cables away from devices that can introduce noise into them, such as machines,
fluorescentlights, and electronics.
• Avoid stretching cables-tension when pulling cables should not exceed 25 pounds (11kg).
• Do not secure cables with any method that might damage them; use approved hangers, such as
those used for telephone wire and RG-6 coaxial wire; available at most hardware stores.
• Do not run cables through conduit. Cables should be treated the same as any other data cable.
Running CANbus cables through conduit will increase the total length required.
136
Liebert iCOM
7.9
Network Layout Options
The Liebert XDP and Liebert XDC have two CANbus ports each (P2 and P4) on the CAN Isolator in
the low voltage side of the electrical box (see Figures 129 and 130). This allows for two chains of the
network to be created to minimize the total network length.
7.9.1
Remote Temperature/Humidity Sensor Placement and Connection to the CANbus
The Liebert XDP and Liebert XDC are shipped with two remote temperature/humidity sensors. One
sensor should be placed closer to the Liebert XDP or Liebert XDC; the other should be placed in the
warmest part of the cold aisle or in the return air stream of a computer room air conditioning unit,
such as as the Liebert DS™ or Liebert CW™.
One shielded CANbus cable is provided with each sensor.
The remote sensors can be placed at the end of a chain or in the middle of a daisy chain as shown.
Refer to Figures 125 and 126 for examples of acceptable network layouts.
Figure 125 Modules on a single chain
Liebert
XDV
Liebert
XDP/
XDC
Liebert
XDP/
XDC
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Remote
Sensor B
Remote
Sensor A
Liebert
XDV
Liebert
XDP/
XDC
Rack
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Remote
Sensor B
Remote
Sensor A
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Remote
Sensor A
Remote
Sensor B
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
137
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Liebert iCOM
Figure 126 Modules on two chains
Liebert
XDV
Liebert
XDP/
XDC
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Rack
Liebert
XDV
Remote
Sensor B
Remote
Sensor A
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Liebert
XDP/
XDC
Remote
Sensor B
Remote
Sensor A
Liebert
XDP/
XDC
Liebert
XDV
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Remote
Sensor B
Remote
Sensor A
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Liebert
XDP/
XDC
Remote
Sensor A
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
138
Rack
Liebert
XDV
Rack
Liebert
XDV
Rack
Liebert
XDV
Remote
Sensor B
Liebert iCOM
7.9.2
CANbus Maximum Length
The CANbus network (the sum of the two CANbus chains) has a maximum length limitation.
• If the Liebert XDP or Liebert XDC with iCOM does not have a CAN Isolator, the maximum
distance is 150 ft. (46m) total network without measuring the final device voltage. The 150 ft.
(46m) total must also include the remote temperature and humidity sensor cable lengths.
• If the Liebert XDP or Liebert XDC contains a CAN Isolator, the maximum distance is 300 ft.
(91m). To exceed this length, the final device voltage must be measured.
7.10
CANbus Cables
The Liebert XDP may be connected to the Smart Modules with a CANbus cable. The shielded cable
consists of three pairs of twisted wires with a 6-pin RJ12 connector.
NOTICE
Risk of improper wiring. Can cause equipment damage.
Mismatching wire pins at the RJ12 connection will damage the CAN device. Extreme caution
should be taken when making cables.
Figure 127 CANbus cable
A
Insulated Ground Wire
(Typical both ends of cable)
Table 54
DPN000786
Pg. 1, Rev. 1
CANbus cable lengths and part numbers
Liebert Part #
Dimension A
ft. (m)
300157G1
6 (1.8)
300157G2
10 (3)
300157G3
20 (6)
300157G4
30 (9.1)
300157G5
60 (18.3)
300157G6
90 (27.4)
300157G7
120 (36.6)
300157G8
150 (45.7)
300157G9
6.25 (1.9)
300157G10
3 (0.9)
300157G11
15 (4.6)
300157G13
40 (12.2)
300157G14
50 (15.2)
300157G15
70 (21.3)
300157G16
80 (24.4)
300157G17
100 (30.5)
300157G18
110 (33.5)
139
Liebert iCOM
Figure 128 CANbus cable plug
Shield Wire
A
Shield Wire
Wire Connections
1
2
3
4
5
6
7.11
Black
Brown
Blue
Violet
Yellow
Green
Detail A
1
Pair 1
2
3
Pair32
4
5
Pair 3
6
Pin #1
DPN000786
Pg. 2, Rev 1
Connecting the CANbus Network
7.11.1 Connection to the Liebert XDP or Liebert XDC
The Liebert XDP and Liebert XDC have two CANbus ports each (P2 and P4) on the CAN Isolator in
the low voltage side of the electrical box (see Figures 129 and 130). This allows for two chains of the
network to be created to minimize the total network length.
Figure 129 CAN Isolator location within the Liebert XDP/XDC
To Remote T/H Sensor A
To Liebert XD Cooling
Module(s) and Remote
T/H Sensor B
To Optional
External
Connections
CAN
Isolator
DPN001598
Pg. 6 Rev. 3
140
Liebert iCOM
Figure 130 P2 and P4 locations on the CAN Isolator
P2
P4
301275
Rev. 2
7.11.2 Connecting to the Liebert XDV Smart Modules
Liebert XDV CANbus Port Locations
The CANbus ports on the Liebert XDV are on the rear of the unit. The cable from the Liebert XDP or
Liebert XDC side will be connected to port P66. The leaving cable will be connected to port P67. See
Figure 131.
Figure 131 Liebert XDV Smart Module CANbus port locations
To Liebert XDP
or Liebert XDC
P66
P66
P67
P67
To next Liebert XDV
or to Remote
Temperature/Humidity
Sensor B
Rear of First
Liebert XDV
Cooling Module
Rear of Next
Liebert XDV
Cooling Module
DPN000783
Rev. 0
141
Liebert iCOM
7.11.3 Connecting to the Liebert XDH Smart Modules
Liebert XDH CANbus Port Locations
The Liebert XDH CANbus ports are located on the side of the electrical box. The cable from the
Liebert XDP or Liebert XDC side will be connected to Port P66. The leaving cable will be connected to
Port P67. See Figure 132.
Figure 132 Liebert XDH CANbus port locations
Front of
Liebert
XDH
Top Electric
Box (cover
removed
for clarity)
P67
P66
DETAIL A
Electric Box typical Middle and
Bottom of Liebert XDH Cooling Module
A
Bottom
Electric
Box
DPN000785
REV 0
Rear of
Liebert XDH
Liebert XDH Single-Circuited CANbus Connections
For Liebert XDHs with both top and bottom circuits tied to the same Liebert XDP or Liebert XDC, the
top and bottom control boards must be tied together using a CANbus cable with a length of
6.25ft. (1.9m). See Figure 133.
142
Liebert iCOM
Figure 133 Single-circuited Liebert XDHs
To Liebert XDP #2 or
Liebert XDC #2
To Liebert XDP #1
or Liebert XDC #1
To next Liebert XDH
or Remote T/H Sensor B
connected to Liebert XDP #1
or Liebert XDC #1
Electric Box in Middle
of Cooling Module
(typical)
Electric Box on Bottom
of Cooling Module
(typical)
XDH20/32 First
Cooling Module
XDH20/32 Next
Cooling Module
To next Liebert XDH Cooling
Module or Remote
T/H Sensor B to Liebert
XDP #2 or Liebert XDC #2
DPN000785
Pg. 2, Rev. 0
Liebert XDH Dual-Circuited CANbus Connections
The Liebert XD Smart Modules are to be tied only to the Liebert XDP or Liebert XDC that they are
mechanically connected to. For Liebert XDHs with the top and bottom circuits tied to different
Liebert XDPs or Liebert XDCs, the control boards must be connected in the same manner. See
Figure 134.
Figure 134 Dual-circuited Liebert XDHs
To Liebert XDP or
Liebert XDC unit
Electric Box in Middle
of Cooling Module
(typical)
Electric Box on Bottom
of Cooling Module
(typical)
XDH20/32 Next
Cooling Module
To next Liebert XDH
DPN000785
Cooling Module or
Remote T/H Sensor B Pg. 2, Rev. 0
XDH20/32 First
Cooling Module
7.11.4 Connecting to the Liebert XD Smart modules
Liebert XDO CANbus Port Locations
The Liebert XDO CANbus ports are located on the side of the electrical box. The cable from the
Liebert XDP or Liebert XDC side will be connected to Port P66. The leaving cable will be connected to
Port P67. See Figure 135.
143
Liebert iCOM
Figure 135 Liebert XDO CANbus port locations
Rear of Liebert XDO
Top of
Liebert XDO
Top of
Liebert XDO
Front of
Liebert XDO
To next Liebert XDO
or Remote T/HSensor B
Right Side of
Liebert XDO
To Liebert XDP/XDC
P66
P67
Section A-A
A
Notes:
1. CANbus signals from the Liebert XDP or Liebert XDC
must be connected to P66 on the first Liebert XDO.
To connect to the next Liebert XDO or Remote T/H Sensor,
plug the CANbus wire into P67 of the previous
Liebert XDO Cooling Module and plug into P66
of the next Liebert XDO or Remote T/H Sensor B.
2. Recommended configuration shown; consult Liebert
for other configurations.
DPN000784
Rev. 1
7.12
CANbus Termination
The last device in the chain must be terminated.
• The remote temperature and humidity sensors are terminated at the factory.
• The Liebert XD smart modules are not terminated at the factory. Improper termination will cause
communication errors.
7.12.1 Remote Temperature and Humidity Sensors Termination
The control board is terminated at the factory. If a remote sensor is the last device in the CANbus
chain, no changes are necessary. The termination jumper must be removed if a remote sensor is not
the last device in the CANbus chain. Refer to the Liebert XD module user manual for terminating
procedures.
7.12.2 Terminating a Smart Module
Liebert XD smart modules must be properly terminated or communication errors will result. Smart
modules are shipped from the factory unterminated. If the smart module is the last device in the
chain—in other words, the last module is not connected to a remote sensor—the smart module control
board must be terminated. Refer to the Liebert XD module user manual for terminating procedures.
144
Monitoring
8.0
MONITORING
The Liebert XDC and Liebert XDP with iCOM allow for control down to the Smart Module level.
Many of the Liebert XD system data points can be monitored through a building management system.
For specific protocol mapping, refer to the protocol specific reference guide for registers, available at
www.liebert.com
Table 55
Liebert XDC/XDP monitoring points
Data Decription
Definitions
Auto Restart Delay
If power is lost, the control will delay this amount of time after power is
restored before restarting the unit.
Calculated Next Maintenance Month
Calculated month of the next scheduled maintenance. Used in
conjunction with (Calculated Next Maintenance Year).
Calculated Next Maintenance Year
Calculated year of the next scheduled maintenance. Used in conjunction
with (Calculated Next Maintenance Month).
Circuit 1 Low Suction Pressure
Compressor Circuit 1 low suction pressure.
Circuit 2 Low Suction Pressure
Compressor Circuit 2 low suction pressure.
Compressor 1A High Head Pressure
Compressor 1A High Head Pressure
Compressor 1A Short Cycle
Compressor 1A short cycle. A short cycle is defined as turning On and
Off a number of times over a set time period.
Compressor 1A State
Compressor 1A operational state.
Compressor 1B High Head Pressure
Compressor 1B high head pressure.
Compressor 1B Short Cycle
Compressor 1B short cycle. A short cycle is defined as turning On and
Off a number of times over a set time period.
Compressor 1B State
Compressor 1B operational state.
Compressor 2A High Head Pressure
Compressor 2A high head pressure.
Compressor 2A Short Cycle
Compressor 2A short cycle. A short cycle is defined as turning On and
Off a number of times over a set time period.
Compressor 2A State
Compressor 2A operational state.
Compressor 2B High Head Pressure
Compressor 2B high head pressure.
Compressor 2B Short Cycle
Compressor 2B short cycle. A short cycle is defined as turning On and
Off a number of times over a set time period.
Compressor 2B State
Compressor 2B operational state.
Customer Input 1
Customer Input 1.
Dew Point Temperature
Dew point temperature, using the highest reading from all sensors.
Ext Air Over Temp Threshold
Threshold value used in the ([Ext Air Sensor A Over Temperature], [Ext
Air Sensor B Over Temperature]...) events.
Ext Air Sensor A Dew Point Temp
Dew point temperature as measured by External Air Sensor A.
Ext Air Sensor A Humidity
Relative humidity as measured by External Air Sensor A.
Ext Air Sensor A Issue
The External Air Sensor A is disconnected or the signal is out of range.
Ext Air Sensor A Over Temperature
(Ext Air Sensor A Temperature) has exceeded (Ext Air Over Temp
Threshold).
Ext Air Sensor A Temperature
Air temperature as measured by External Air Sensor A.
Ext Air Sensor A Under Temperature
(Ext Air Sensor A Temperature) has dropped below (Ext Air Under Temp
Threshold).
Ext Air Sensor B Dew Point Temp
Dew point temperature as measured by External Air Sensor B.
Ext Air Sensor B Humidity
Relative humidity as measured by External Air Sensor B.
Ext Air Sensor B Issue
The external air sensor B is disconnected or the signal is out of range.
Ext Air Sensor B Over Temperature
(Ext Air Sensor B Temperature) has exceeded (Ext Air Over Temp
Threshold).
Ext Air Sensor B Temperature
Air temperature as measured by External Air Sensor B.
145
Monitoring
Table 55
Liebert XDC/XDP monitoring points (continued)
Data Decription
Definitions
Ext Air Sensor B Under Temperature
(Ext Air Sensor B Temperature) has dropped below (Ext Air Under Temp
Threshold).
Ext Air Under Temp Threshold
Threshold value used in the ([Ext Air Sensor A Under Temperature], [Ext
Air Sensor B Under Temperature]...) events.
Ext Dew Point Over Temp Threshold
Threshold value used in the (Ext Dew Point Over Temperature) event.
Ext Dew Point Over Temperature
At least one dew point temperature reading ([Ext Air Sensor A Dew Point
Temp], [Ext Air Sensor B Dew Point Temp]...) has exceeded (Ext Dew
Point Over Temp Threshold).
Fan Issue
One or more fans are not operating within their operational parameters.
Hot Gas Solenoid Valve 1 Position
Hot gas solenoid Valve 1 position.
Hot Gas Solenoid Valve 2 Position
Hot gas solenoid Valve 2 position
Hot Gas Valve 1 Open Position
Hot gas Valve 1 open position.
Hot Gas Valve 2 Open Position
Hot gas Valve 2 open position.
Maintenance Ramp
The ratio of operations performed to the calculated operations available
between maintenance intervals.
Minimum Room Temperature Set Point
Minimum desired room air temperature. If the room air temperature falls
below this set point, the unit will reduce the cooling.
Pump 1 Loss of Flow
Loss of flow is detected in Pump 1. The loss of flow condition occurs
when no differential pressure is detected across the pump.
Pump 1 State
Pump 1 operational state.
Pump 2 Loss of Flow
Loss of flow is detected in Pump 2. The loss of flow condition occurs
when no differential pressure is detected across the pump.
Pump 2 State
Pump 2 operational state.
Pump Short Cycle
Pumps have short cycled. A short cycle is defined as turning On and Off
a number of times over a set time period.
Shutdown - Loss Of Power
System lost power. This event becomes active when the unit is powered
on following an unexpected loss of power.
Supply Refrig Over Temp Threshold
Threshold value used in the (Supply Refrigerant Over Temp) event.
Supply Refrig Over Temp Threshold
Threshold value used in the (Supply Refrigerant Over Temp) event.
Supply Refrigerant Over Temp
Event that is activated when (Supply Refrigerant Temperature) exceeds
(Supply Refrig Over Temp Threshold). The event is deactivated when
the temperature drops below the threshold.
Supply Refrigerant Temp Sensor Issue
The supply refrigeramt temperature sensor is disconnected or the signal
is out of range.
Supply Refrigerant Temperature
Supply refrigerant temperature.
Supply Refrigerant Under Temp
(Supply Refrigerant Temperature) has dropped below a specified
threshold.
System Condensation Detected
System condensation detected.
System Control Mode
System Control Mode
System Date and Time
The system date and time
System Event Acknowledge/Reset
Reset and/or acknowledge all events.
System On/Off Control
Turn system functionality On or Off.
System Operating State
Current operating state of the system.
System Status
The operating status for the system
146
Monitoring
Table 56
Liebert XD Smart Module monitoring points
Data Decription
Definitions
Cold Aisle Over Temp Threshold
Upper threshold value used in the (Cold Aisle Temp Out of Range) event.
Cold Aisle Over Temp Threshold
Upper threshold value used in the (Cold Aisle Temp Out of Range) event.
Cold Aisle Temp Out of Range
The air temperature in the cold aisle is either above (Cold Aisle Over Temp
Threshold) or below (Cold Aisle Under Temp Threshold).
Cold Aisle Under Temp
Threshold
Lower threshold value used in the (Cold Aisle Temp Out of Range) event.
Cold Aisle Under Temp
Threshold
Lower threshold value used in the (Cold Aisle Temp Out of Range) event.
Communication Status
Communication status of remote device.
Cooling Capacity
Cooling capacity in use, expressed as a percentage of the maximum rated
capacity.
Cooling Capacity
Cooling capacity in use, expressed in kilowatts.
Ext Fan Issue
One or more fans are not operating within their operational parameters.
Ext Fan Issue - Event Control
Enable/disable the activation of the (Ext Fan Issue) event. If set to “disabled,”
the event will not be annunciated. This implies that the event will not be placed
in any active event list or in any event history list.
Ext Fan Issue - Event Type
The event type for the (Ext Fan Issue) event.
Ext Remote Shutdown
Unit is shut down by a remote signal.
Ext Remote Shutdown - Event
Control
Enable/disable the activation of the (Remote Shutdown) event. If set to
'disabled', the event will not be annunciated. This implies that the event will not
be placed in any active event list or in any event history list.
Ext Remote Shutdown - Event
Type
The event type for the (Remote Shutdown) event.
Ext System Condensation
Detected
External system condensation detected.
Ext System Condensation
Detected - Event Control
Enable/disable the activation of the (Ext System Condensation Detected)
event. If set to “disabled,” the event will not be annunciated. This implies that
the event will not be placed in any active event list or in any event history list.
Ext System Condensation
Detected - Event Type
The event type for the (Ext System Condensation Detected) event.
Fan Button Control
Enable or disable the buttons from controlling the state of the fans.
Fan On/Off Control
Turn system fans On or Off.
Hot Aisle Over Temp Threshold
Upper threshold value used in the (Hot Aisle Temp Out of Range) event.
Hot Aisle Over Temp Threshold
Upper threshold value used in the (Hot Aisle Temp Out of Range) event.
Hot Aisle Temp Out of Range
The air temperature in the Hot aisle is either above (Hot Aisle Over Temp
Threshold) or below (Hot Aisle Under Temp Threshold).
Hot Aisle Under Temp Threshold
Lower threshold value used in the (Hot Aisle Temp Out of Range) event.
Hot Aisle Under Temp Threshold
Lower threshold value used in the (Hot Aisle Temp Out of Range) event.
Primary Fan Group State
Current operational state of the primary fan group.
147
Monitoring
Table 56
Liebert XD Smart Module monitoring points (continued)
Data Decription
Definitions
Sensor Issue
One or more sensors are disconnected or the signals are out of range.
Sensor Issue - Event Control
Enable/disable the activation of the (Sensor Issue) event. If set to 'disabled',
the event will not be annunciated. This implies that the event will not be placed
in any active event list or in any event history list.
Sensor Issue - Event Type
The event type for the (Sensor Issue) event.
Fan Economy Mode
Mode in which system secondary fans are to be controlled.
Fan State
Current operational state of a group of fans.
Module Refrigerant Temperature
Refrigerant temperature as measured by Module Sensor
Module Sensor 1 Temperature
Air temperature as measured by Module Sensor 1
Module Sensor 2 Temperature
Air temperature as measured by Module Sensor 2
Module Sensor 3 Temperature
Air temperature as measured by Module Sensor 3
Visual ID Control
Visual identification control to display an LED flashing sequence, allowing it to
be visually located.
Table 57
System data points
Data Decription
Definitions
Unit Communication Lost
Master has lost communication with one or more networked units.
RAM Battery Issue
RAM or RAM backup battery is not operating correctly.
Master Unit Communication Lost
Communication with master unit has been lost.
Remote Shutdown
Unit is shut down by a remote signal.
Unit Code Missing
Unit code has not been entered and saved.
Unit On
Unit was turned on.
Unit Off
Unit was turned Off.
Unit Standby
Unit was placed in standby mode.
Unit Partial Shutdown
An event has occurred requiring some system components to be shutdown
and disabled.
Unit Shutdown
An event has occurred requiring the unit to be shutdown and disabled to
prevent damage to the system.
Maintenance Due
The calculated maintenance date has been reached.
Maintenance Completed
Maintenance has been completed on the unit.
System Operating State Reason
The reason the system is in the current operating state.
System Date and Time
The system date and time
Table 58
Communication cards for Liebert XD units
Communication
Card
Protocol
IS-WEBL
SNMPv1, SNMPv2c, HTTP, HTTPS, Email, SMS, Telnet, Liebert Protocol
IS-485L
Modbus 485
IS-IPBML
HTTP, HTTPS, Telnet, Modbus, IP, BACnet IP
IS-485EXI
Liebert SiteScan®
148
Specifications and Model Number Nomenclature
9.0
SPECIFICATIONS AND MODEL NUMBER NOMENCLATURE
Table 59
Liebert XDCF specifications
Models
XD-CF-10-BP-*, XD-CF-10-TP-*
XD-CF-10-BPE-*, XD-CF TPE-*
Cooling capacity, maximum
10kWH / 2.8 Tons / 34,000 BTUh
55°F (13°C) entering fluid temperature,
50°F (10°C) or lower dew point
Conditions
Dimensions, inches (mm)
Height – including pipe connections
31-3/8" (797mm)
Width
13-7/16" (341mm)
Depth
7-5/16" (186mm)
Weight, lb (kg)
Module only
18 (8.2)
Shipping weight
30 lb. (13.06 kg)
Pipe connections
Refrigerant Supply
from Liebert XDP/Liebert XDC
Refrigerant Return
to Liebert XDP/Liebert XDC
1/2" threaded one-shot coupling on the module
5/8" threaded one-shot coupling on the unit
Gray
Cabinet exterior finish
Agency
Safety
CSA — CE
Figure 136 Liebert XDCF model number nomenclature
Example: XD-CF-10-BP—*
XD
Liebert
Xtreme
heat
density
system
CF
10
B
Model Size
Module for
BladeFrame EX
P
—
P = Coupling
T = Top
B = Bottom
149
- = Domestic Packaging
E = Export Packaging
*
Revision
level
Specifications and Model Number Nomenclature
Table 60
Liebert XDH20 specifications
XDH20BK 1
XDH20SK 1
(60Hz)
Models
XDH20BS 1
XDH20SS 1
(50/60Hz)
XDH20, 60Hz Nominal (98ºF [37°C] EAT): 22kW/6.3 Tons
XDH20, 60Hz Maximum(105ºF [41°C] EAT): 25.3kW/7.2 Tons
XDH20, 50Hz Nominal (98ºF [37°C] EAT): 21.6kW / 6.1 Tons
XDH20, 50Hz Maximum(105ºF [41°C] EAT): 25.3kW/7.2 Tons
Cooling Capacity
Capacity rating is @ 55ºF (13ºC) Entering Fluid Temperature
and 50ºF (10ºC) or lower dew point
Conditions
Electrical Requirements
120V-1ph-60Hz
220-240V-1ph-50Hz, CE /
208-240V-1ph-60Hz, CSA
Two IEC320-C14 power inlets and two IEC
power cords with NEMA 5-15P plugs
Two IEC320-C14 power inlets and two IEC
power cords with IEC320-C14 plugs
5
2.5
600
575
Input
Input Power Connections
Full Load Amps
Power Consumption,
Nominal, Watts
Dimensions, inches (mm)
Height—Module Only
78 (1981)
Height—Including
Pipe Connections
80 (2032)
Width
12 (305)
Depth
42 (1067)
Weight, lb (kg)
Module Only
233 (106)
Shipping Weight
317 (144)
233 (106)
317 (144)
6
Number of Fans
Airflow, Nominal, ft3/min
(m3/hr)
Audible Noise, Sound Power
2500 (4248)
2428 (4125)
81 dBa
81 dBa
Pipe Connections
Refrigerant Supply
1/2" OD, Cu
Refrigerant Return
7/8" OD, Cu
Fans and electrical components
Serviceable Parts
Cabinet Exterior Finish
Black, matte finish, heat-fused powder coat
Options
Smart Module control
board (factory-installed)
Dry contact (24VAC - 1A maximum)
Pre-Charged Refrigerant
R-134a refrigerant, one-shot connections
Air Diffusers
Uni-directional or bi-directional
Agency
Approvals
CSA 60Hz
1. Refer to Figure 137 for complete part number.
150
CE 50Hz, CSA 50/60Hz
Specifications and Model Number Nomenclature
Table 61
Liebert XDH32 specifications
Models
XDH32BK 1
XDH32SK 1
(60Hz)
XDH32BS 1
XDH32SS 1
(50/60Hz)
Cooling Capacity
XDH32, 60Hz Nominal (98ºF [37°C] EAT): 30kW/8.5 Tons
XDH32, 60Hz Maximum(105ºF [41°C] EAT): 34kW/9.7 Tons
XDH32, 50Hz Nominal (98ºF [37°C] EAT): 30kW / 8.5 Tons
XDH32, 50Hz Maximum(103ºF [39°C] EAT): 34kW/9.7 Tons
Conditions
Capacity rating is @ 55ºF (13ºC) Entering Fluid Temperature
and 50ºF (10ºC) or lower dew point
Electrical Requirements
120V-1ph-60Hz
220-240V-1ph-50Hz, CE /
208-240V-1ph-60Hz, CSA
Two IEC320-C14 power inlets and two IEC
power cords with NEMA 5-15P plugs
Two IEC320-C14 power inlets and two IEC
power cords with IEC320-C14 plugs
10
5
1200
1150
Input
Input Power Connections
Full Load Amps
Power Consumption,
Nominal, Watts
Dimensions, inches (mm)
Height—Module Only
78 (1981)
Height—Including
Pipe Connections
80 (2032)
Width
12 (305)
Depth
42 (1067)
Weight, lb (kg)
Module Only
246 (112)
246 (112)
Shipping Weight
330 (150)
330 (150)
6
Number of Fans
Airflow, Nominal,
ft3/min (m3/hr)
Audible Noise,
Sound Power
4000 (6796)
3850 (6541)
86 dBa
86 dBa
Pipe Connections
Refrigerant Supply
1/2" OD, Cu
Refrigerant Return
7/8" OD, Cu
Fans and electrical components
Serviceable Parts
Cabinet Exterior Finish
Black, matte finish, heat-fused powder coat
Options
Smart Module control
board (factory-installed)
Dry contact (24VAC - 1A maximum)
Pre-Charged Refrigerant
R-134a refrigerant, one-shot connections
Air Diffusers
Uni-directional or bi-directional
Agency
Approvals
CE 50Hz, CSA 50/60Hz
CSA 60Hz
1. Refer to Figure 137 for complete part number.
151
Specifications and Model Number Nomenclature
Figure 137 Liebert XDH model number nomenclature
Example: XDH32BK— —*
XD
H
Liebert
Xtreme heat
density system
32
20 = Model size
32 = Model size
Horizontal
row cooler
B
K
—
K = 120V-1ph-60Hz
S = 208-240-1ph-60Hz
220-240-1ph-50Hz
B = Basic module
S = Smart module
152
—
*
— = Domestic packaging
E = Export packaging
— = Hard piped
P = Pre-charged
One-Shot Coupling
R = Removable Coupling
Revision
level
Specifications and Model Number Nomenclature
Table 62
Liebert XDO16 specifications
XDO16BK 1
XDO16SK 1
(60Hz)
Models
XDO16BS 1
XDO16SS 1
(60Hz)
XDO16BS 1
XDO16SS 1
(50Hz)
Nominal (85°F [29.4°C]
EAT): 14kW/4.0Tons
Maximum (93°F [34°C]
EAT): 17.3 kW / 4.9 Tons
Nominal (85°F [29.4°C] EAT): 16kW / 4.5 Tons
Maximum (90°F [32°C] EAT): 17.3 kW / 4.9 Tons
Cooling Capacity
Capacity rating is @ 55°F (13°C) Entering Fluid Temperature and 50ºF or lower dew point
Conditions
Electrical Requirements
Input Voltage
1ph-60Hz-120V
Input Power Connections
1ph-60 Hz-220-240V
1ph-50 Hz-220-240V
Terminal blocks provided internal to module
Full Load Amps
2.7A @ 120V
1.50 @ 230V
1.50 @ 230V
Wire Size Amps
3.4
2.0
2.0
Overcurrent Protection Device
15
15
15
Power consumption,
nominal, watts
335
350
350
Dimensions, inches (mm)
Length
72-1/4 (1835)
Width
24-1/8 (613)
Height
22-1/2 (572) not including electrical and piping access
Weight, lb (kg)
Module only
150 (68)
Shipping weight
238 (108)
296 (134)
Installed, with refrigerant,
without options
155 (70)
1
Number of Fans
Airflow, Nominal, ft3/ min
(m3/ hr)
Audible Noise
1
1
2700 (4587)
2250 (3822)
85 dBa sound power
83 dBa sound power
Pipe Connections
Refrigerant Supply
from Liebert XDP/Liebert XDC
1/2" OD, Copper
Refrigerant Return
to Liebert XDP/Liebert XDC
7/8" OD, Copper
Fan and electrical components
Serviceable Parts
Exterior Finish – Bottom,
Sides, Front and Rear
Black, matte finish, heat-fused powder coat
Hot-dipped galvanized steel
Exterior Finish - Top
Agency
Approvals
CSA 60 Hz
CSA 60Hz
1. Refer to Figure 138 for full part number.
153
CE 50Hz
Specifications and Model Number Nomenclature
Table 63
Liebert XDO20 specifications
XDO20BK 1
XDO20SK 1
XDO20BS 1
XDO20SS 1
60Hz
Models
60Hz
50Hz
Nominal (92°F [33°C] EAT):
17.7kW / 5 Tons
Maximum (103°F [39°C]
EAT): 23.1kW / 6.6 Tons
Nominal (92°F [33°C] EAT): 20kW / 5.7 Tons
Maximum (100°F [38°C] EAT): 23.1kW / 6.6 Tons
Cooling Capacity
Capacity rating is @ 55ºF (13°C) Entering Fluid Temperature and 50ºF (10°C) or lower dew
point
Conditions
Electrical Requirements
Input Voltage
1ph-60Hz-120V
Input Power Connections
1ph-60Hz-220-240V
1ph-50 Hz-220-240V
Terminal blocks provided internal to module
Full Load Amps
2.7A @ 120V
1.64A @ 230V
1.64A @ 230V
Wire Size Amps
3.4
2.0
2.0
Overcurrent Protection Device
15
15
15
Power consumption,
nominal, watts
335
350
350
Dimensions, inches (mm)
Length
72-1/4 (1835)
Width
24-1/8 (613)
Height
22-1/2 (572) not including electrical and piping access
Weight, lb (kg)
Module only
Shipping weight
150 (68)
238 (108)
296 (134)
Installed, with refrigerant,
without options
1
Number of Fans
Airflow, Nominal,
(m3/ hr)
155 (70)
ft3/
min
Audible Noise
1
1
2700 (4590)
2250 (3820)
85 dBa sound power
83 dBa sound power
Pipe Connections (without flex pipe)
Refrigerant Supply
from Liebert XDP/Liebert XDC
1/2" OD, Copper
Refrigerant Return
to Liebert XDP/Liebert XDC
7/8" OD, Copper
Fan and electrical components
Serviceable Parts
Exterior Finish – Bottom,
Sides, Front and Rear
Black matte finish, heat-fused powder coat
Hot-dipped galvanized steel
Exterior Finish - Top
Agency
Approvals
CSA 60 Hz
1. Refer to Figure 138 for full part number.
154
CE 50Hz
Specifications and Model Number Nomenclature
Figure 138 Liebert XDO model number nomenclature
Example: XDO20BK– –*
XD
O
20
Liebert Xtreme
heat density
system
K
B = Basic module
S = Smart module
–
*
- = Domestic Packaging
E = Export Packaging
— = Hard-Piped
P = Pre-charged
One-Shot Coupling
R = Removable Coupling
Revision
level
Options for Liebert XDO20 and Liebert XDO16
Option
Liebert XDO - 60Hz Models
Liebert XDO - 50Hz Models
2 Liebert XDOs per lighting unit; 120V or 277V; 4’ standard fluorescent tubes (not
included)
Lighting Fixtures (ship loose)
0.9A per 120V light fixture;
0.4A per 277V light fixture
Power, optional lighting fixture
Smart Module control board
(factory-installed)
None
Dry contact 24VAC - 1A maximum
Pre-Charged Refrigerant
Table 65
–
K = 120V-1ph-60Hz
S = 220-240V-1ph-60Hz,
220-240V-1ph- 50Hz
16 = Model size
20 = Model size
Overhead
cooling
module
Table 64
B
R-134a Refrigerant, one-shot connections
Liebert XDO dimensions—domestic and export
Shipping Dimensions, inches (mm)
Domestic
Module Dimension
Unpacked, inches (mm)
Export
Model
Length
Width
Height
Length
Width
Height
Length
Width
Height *
All Models
84 (2134)
30 (762)
30 (762)
83 (2108)
30 (762)
30 (762)
72-1/4
(1835)
24-1/8
(613)
25-1/2
(648)
* Includes piping connections
155
Specifications and Model Number Nomenclature
Table 66
Liebert XDR20 specifications
XDR20B1- *
Models
Cooling Capacity, Nominal,
rated at 104ºF (40°C) EAT & 2400ft3/m (68m3/m)
XDR20B1P *
(Precharged R134a)
XDR20B1R *
20.5 kW (5.8 tons)
55°F (13°C) entering fluid temperature
50°F (10°C) or lower dew point
Conditions
Dimensions, inches (mm)
Height, Including Pipe Connections
82-3/8 (2093)
83-1/2 (2121)
Width With Handles Attached
27-3/8 (695)
Handles Removed
23-1/2 (597)
Depth
6-1/2 (165)
Shipping Length
90 (2286)
Shipping Width
30-1/2 (775)
Shipping Depth
15-1/2 (394)
Max Shipping Depth (4 modules)
80 (2032)
62 (1575)
Weight, lb (kg)
Module Only
130 (59)
133 (60)
130 (59)
Shipping
225 (103)
228 (104)
225 (103)
Pipe Connections
Refrigerant Supply
1/2" OD Type ACR
Refrigerant Return
7/8" OD Type ACR
Black Matte, Heat-Fused Powder Coat
Exterior Finish
CSA, CE Approved
Safety
*
Refer to Figure 139 for the complete part number.
Table 67
Liebert XDR rack mounting kit
Rack
Part #
Knurr Miracel
198163G1
Dell PowerEdge 4210
199050G1
HP 10642
199051G1
APC AR3100
199054G1
Figure 139 Liebert XDR model number nomenclature
Example: XDR20B1R — *
XD
Liebert
Xtreme
heat
density
system
R
20
B
1
20 = Model Size
Rear Cooling Module
R
1 = Standard
B = Basic Module
156
—
*
- = Domestic Packaging
E = Export Packaging
- = Hard-Piping
P = Pre-Charged One-Shot
Coupling
R = Removable Coupling
Revision
level
Specifications and Model Number Nomenclature
Table 68
Liebert XDV8 specifications
XDV8BK 1
XDV8SK 1
XDV8BT 1
XDV8ST 1
60 Hz
Models
60 Hz
50 Hz
Nominal (92°F [33°C] EAT): 8kW / 2.3 Tons
Maximum (95°F [35°C] EAT): 8.7kW / 2.5 Tons
Cooling Capacity
XDV8BS 1
XDV8SS 1
50 Hz
Nominal (92°F [33°C] EAT): 7kW/ 2.0 Tons
Maximum (103°F [39°C] EAT): 8.7kW/2.5Tons
Capacity rating is @ 55ºF (13ºC) Entering Fluid Temperature and
50ºF (10ºC) or lower dew point, rear air inlet.
Conditions
Electrical Requirements
Input
120V model: 1ph-60 Hz
230V model: 1ph-60
Hz
Input power connections
Full Load Amps
Power consumption,
nominal, watts
230V model: 1ph-50 Hz
2 power connections, each model
120V model: 2.0A
230V model: 1.0A
180
190
190
190
Dimensions, in. (mm)
Height – module only
14 (355) not including pipe connections
Height – including pipe
connections
18-5/8 (473)
Width
22-7/8 (581)
Depth – Top
39-1/2 (1003)
Depth – Bottom
29-5/8 (752)
Weight, lb (kg)
Module only
77 (35)
Shipping weight
125 (57)
Installed, with
refrigerant
79 (36)
Number of Fans
Airflow, Nominal,
ft3/ min (m3/ hr)
Audible noise
2
2
2
2
1000 (1699) with rear inlet.
Bottom inlet airflow may be less,
depending on restrictions inside cabinet
833 (1415) with rear inlet.
Bottom inlet airflow may be less,
depending on restrictions inside cabinet
78 dBa sound power
73 dBa sound power
Pipe Connections (without Liebert Flex Pipe)
Refrigerant Supply
from Liebert
XDP/Liebert XDC
1/2" OD Cu, (optional 1/2" threaded coupler flex piping)
Refrigerant Return
to Liebert XDP/Liebert
XDC
5/8" OD Cu, (optional 3/4" threaded coupler flex piping)
Fans and electrical components
Serviceable Parts
Cabinet Exterior
Finish
Black, matte finish, heat-fused powder coat
Options
Smart Module control
board (factory-installed)
Pre-Charged
Refrigerant
Dry contact, 24VAC, 1A maximum
R-134a refrigerant, one-shot connections
Agency
Approvals
CSA 60Hz
CSA 50Hz
1. Refer to Figure 140 for complete part number.
157
CE 50Hz
Specifications and Model Number Nomenclature
Table 69
Liebert XDV10 specifications
XDV10BK 1
XDV10SK 1
XDV10BT 1
XDV10ST 1
60 Hz
Models
XDV10BS 1
XDV10SS 1
60 Hz
50 Hz
50 Hz
Nominal (98ºF [37ºC] EAT: 10kW / 2.8 Tons
Nominal (98ºF [37ºC] EAT): 8.3kW / 2.4 Tons
Maximum (106ºF [41ºC] EAT): 11.7kW/3.3 Tons Maximum (116ºF [47ºC] EAT): 11.7kW/3.3 Tons
Cooling Capacity
Capacity Rating is @ 55ºF (13ºC) Entering Fluid Temperature and
50ºF (10ºC) or lower dew point, rear air inlet.
Conditions
Electrical Requirements
Input 120V model: 1ph-60 Hz 230V model: 1ph-60 Hz
Input power connections
Full Load Amps
Power consumption,
nominal, watts
230V model: 1ph-50 Hz
2 power connections, each model
120V model: 2.0A
230V model: 1.0A
180
190
190
190
Dimensions, in. (mm)
Height – module only
14 (355) not including pipe connections
Height – including hard
pipe connections
18-5/8 (473)
Height – including oneshot connections
19-5/8 (498)
Width
22-7/8 (581)
Depth – Top
39-1/2 (1003)
Depth – Bottom
29-5/8 (752)
Weight, lb (kg)
Module only
77 (35)
Shipping weight
125 (57)
Installed, with refrigerant
79 (36)
Number of fans
Airflow, Nominal,
ft3/ min (m3/ hr)
Audible noise
2
2
2
2
1000 (1699) with rear inlet.
Bottom inlet airflow may be less,
depending on restrictions inside cabinet
833 (1415) with rear inlet.
Bottom inlet airflow may be less,
depending on restrictions inside cabinet
78 dBa sound power
73 dBa sound power
Pipe Connections (without Liebert Flex Pipe)
Refrigerant supply
from Liebert XDP/ XDC
1/2" OD, Cu, (optional 1/2" threaded coupler flex piping)
Refrigerant return
to Liebert XDP/ XDC
5/8" OD, Cu, (optional 3/4" threaded coupler flex piping)
Fans and electrical components
Serviceable Parts
Cabinet Exterior Finish
Black, matte finish, heat-fused powder coat
Options
Smart Module control
board (factory-installed)
Dry contact, 24VAC, 1A maximum
Pre-Charged Refrigerant
R-134a refrigerant, one-shot connections
Agency
Approvals
CSA 60Hz
CSA 50Hz
1. Refer to Figure 140 for complete part number.
158
CE 50Hz
Specifications and Model Number Nomenclature
Table 70
Liebert XDV dimensions—domestic and export
Module Dimensions Unpacked
Length x Width x Height
inches (mm)
Shipping Dimensions
Length x Width x Height
inches (mm)
Model
Domestic
Export
Module Only
All Models
48 x 40 x 24-1/4
(1219 x 1016 x 616)
45-4/5 x 30-3/4 x 33
(1163 x 781 x 839mm)
39-1/2 x 22-7/8 x 14
(1003 x 581 x 356)
Figure 140 Liebert XDV model number nomenclature
Example: XDV10BK– –*
XD
V
10
B
8 = Model size
10 = Model Size
Liebert Xtreme
heat density
system
Vertical top
cooler
K
—
K = 120V-1ph-60Hz
S = 230V, 1ph-50Hz
T = 208-240V-1ph-60Hz,
220-240-1ph-50Hz
B = Basic module
S = Smart module
159
—
*
— = Domestic
Packaging
E = Export
Packaging
— = Hard piped
P = Pre-charged
One-Shot Coupling
R = Removable coupling
Revision
level
Specifications and Model Number Nomenclature
Table 71
Liebert XDC160 specifications
XDC160 Air
Models
Cooling Capacity, tons (kW)
XDC160 Water / Glycol
XDC160AA
XDC160AM
46 (160)
37 (130)
189192G3 (90-100°F)
189192G5 (65-85°F)
See Tables 72, 73 and 74 for
Water/Glycol
performance data
40% of system nominal capacity (64 kW for 60Hz unit)
Minimum Load
Electrical Requirements
Input 460V-3ph-60Hz 380/415V-3ph-50Hz
Full Load Amps
460V-3ph-60Hz
79A
Minimum supply wire sizing ampacity
84A
Maximum fuse or circuit breaker size
100A
Dimensions, inches (mm)
Height - Main unit only
78 (1981)
Height - Main unit only, as shipped
83 (2108)
Width - Main unit
74 (1879)
Depth - Main unit
34-5/8 (879)
Height - Water/Glycol-Cooled Condenser Stand
N/A
24 (607)
Width - Water/Glycol-Cooled Condenser Stand
N/A
72 (1829)
Depth - Water/Glycol-Cooled Condenser Stand
N/A
33 (839)
Weight, lb (kg)
Main unit only
1800 (817)
Main unit only, as shipped
Domestic: 1945 (882); Export: 2093 (949)
Water/Glycol-Cooled Condenser Stand
N/A
1075 (488)
Water/Glycol-Cooled Condenser Stand, as shipped
N/A
1150 (521)
Pipe Connections, inches, O.D., Cu
Liebert XD Coolant supply to Liebert XD cooling
modules
1-1/8
Liebert XD Coolant return from Liebert XD cooling
modules
2-1/8
Liquid line, DX circuit
7/8
Hot gas line, DX circuit
1-3/8
Heat Rejection Equipment
95°F (35°C) ambient air-cooled condenser
2-DCSL415
N/A
105°F (41°C) ambient air-cooled condenser
2 -DCSL616
N/A
Number of Liebert XD Cooling Modules Connected, Maximum (Minimum)
Liebert XDCF10
16 (6)
Liebert XDH20
8 (4)
Liebert XDH32
5 (2)
Liebert XDO16
10 (4)
Liebert XDO20
8 (4)
Liebert XDV8
20 (8)
Liebert XDV10
16 (7)
Black, matte finish, heat-fused powder coat
Cabinet Exterior Finish
86 (30)
Maximum Ambient Operating Temperature °F (°C)
Agency
Approvals
CSA
160
CE
CSA
Specifications and Model Number Nomenclature
Table 72
Floor stand specifications—water-cooled Liebert XDC
XDC160 Water Floor Stand - 60Hz
189192G3
189192G5
Entering Fluid Temp °F (°C)
65 (18)
70 (21)
75 (24)
85 (29)
95 (35)
46.1(162.3)
46.1(162.3)
46.1(162.3)
46.1(162.3)
44.5(156.5)
Performance Data
Cooling capacity, tons (kW)
Flow, GPM
Pressure Drop, psi (Ft Water)
50
58
70
110
142
2.7 (6.2)
4.9 (11.3)
5.4 (12.5)
20.7 (47.8)
27.3 (63.1)
1"
1"
1"
1"
1"
2-1/8"
2-1/8"
2-1/8"
2-1/8"
2-1/8"
Heat Rejection Equipment
Water regulating valve size
Piping Connections
Water / glycol supply and return lines
Table 73
Floor stand specifications—Liebert XDC with 40% propylene glycol
XDC160 Glycol Floor Stand - 60Hz - 40% PG
189192G3
Outside Ambient °F (°C)
95 (35)
100 (38)
105 (41)
Max Entering Fluid Temp °F (°C)
110 (43)
110 (43)
110 (43)
Performance Data
Cooling capacity, tons (kW)
42.5 (149.4)
Total Heat Rejection, (kW)
192.6
Flow, GPM
206
Pressure Drop, psi (ft water)
37.2 (85.9)
Heat Rejection Equipment
Drycooler
DDNT 940A
2 x DDNT 880A*
6.7 (15.8)
2.9 (6.6)
Drycooler Pressure Drop, psi (ft water)
Glycol pump package - 10hp
460V - D10ANTS1317; 208V - D10YNTS1317
Pump Control Package - 208V
RP020HY04S0758
Pump Control Package - 460V
RP020HA08S0758
Pump Total Head @ 206 GPM, ft water
145
Water regulating valve size
1-1/4"
Piping Connections
Water / glycol supply and return lines
2-5/8"
* When multiple drycoolers are used, ensure flow is balanced.
161
Specifications and Model Number Nomenclature
Table 74
Floor stand specifications—Liebert XDC with 40% ethylene glycol
XDC160 Glycol Floor Stand - 60Hz - 40% EG
189192G3
Outside Ambient °F (°C)
95 (35)
100 (38)
105 (41)
Max Entering Fluid Temp °F (°C)
110 (43)
110 (43)
110 (43)
Performance Data
Cooling capacity, tons (kW)
42.5 (149.4)
Total Heat Rejection, (kW)
192.6
Flow, GPM
204
Pressure Drop, psi (ft water)
35.9 (82.9)
Heat Rejection Equipment
Drycooler
DDNT 940A
2 x DDNT 880A*
6.5 (15.1)
2.7 (6.3)
Drycooler Pressure Drop, psi (ft water)
Glycol pump package - 10HP
460V - D10ANTS1317; 208V - D10YNTS1317
Pump Control Package - 208V
RP020HY04S0758
Pump Control Package - 460V
RP020HA08S0758
Pump Total Head @ 204 GPM, ft water
145
Water regulating valve size
1-1/4"
Piping Connections
Water / glycol supply and return lines
2-5/8"
* When multiple drycoolers are used ensure flow is balanced.
Figure 141 Liebert XDC model number nomenclature
Example: XDC160AA– –*
XD
Liebert
Xtreme heat
Density system
C
Chiller
unit
160
A
A
Place holder
Model size
–
Place holder
Voltage-phase-frequency
A = 460V-3ph-60Hz
M = 380/415-3ph-50Hz
162
–
Place holder
*
Revision
level
Specifications and Model Number Nomenclature
Table 75
Liebert XDP160 specifications
XDP160RC--3
Models
XDP160RA--3
160kW / 46 Tons, 60Hz
XDP160RM--3
140kW / 40 Tons, 50Hz
Each capacity is based on 45ºF (7ºC) entering water temperature and
140gpm (530lpm) water flow rate. Capacity is reduced when glycol mixtures
are used in place of 100% water.
Cooling Capacity, Nominal
30% of nominal system capacity or 48kW (163,800BTU/H)
Minimum Load
Electrical Requirements
Input
Full Load Amps
208V/3ph/60Hz
460V/3/ph60Hz
380/415V/3ph/50Hz
4A
2.1A
2.3A
Dimensions, inches (mm)
Height – Unit only
78 (1981)
Height – As shipped
83 (2108)
Width
38 (965)
Depth
34 (864)
Unit only
821 (372)
Weight, lb (kg)
Shipping weight
Domestic: 990 (449); Export: 1067 (484)
Installed, with refrigerant and chilled water
1038 (471)
Pipe Connections
Refrigerant supply to Liebert XD cooling
module
1-1/8" OD, Cu
Refrigerant return from Liebert XD cooling
module
2-1/8" OD, Cu
Chilled water supply and return
2-5/8" OD, Cu
2-way, 2" nominal; 35 PSIG close-off pressure rating;
150 PSIG maximum allowable pressure
Control valve
Pressure Drop – Chilled Water Side
20 psig (137kPa, 1.38bar), with 140 gpm (530lpm) water flow rate,
control valve fully open
Temperature Rise – Chilled Water Side
at rated flow, °F (°C)
8.0 (4.4)
6.9 (3.8)
Number of Liebert XD Cooling Modules Connected, Maximum (Minimum)
Liebert XDCF10
16 (5)
Liebert XDH20
8 (3)
Liebert XDH32
5 (2)
Liebert XDV8
20 (6)
Liebert XDV10
16 (5)
Liebert XDO16
10 (3)
Liebert XDO20
8 (3)
Black, matte finish, heat-fused powder coat
Cabinet Exterior Finish
Operating Ambient
Temperature, Maximum, °F (°C)
86 (30)
Agency
Approvals
CSA 60Hz
163
CE 50Hz
Specifications and Model Number Nomenclature
Figure 142 Liebert XDP model number nomenclature
Example: XDP160RA– –*
XD
P
160
Pumping
unit
Liebert
Xtreme heat
Density system
R
A
Pump
Redundancy
Model size
–
Place holder
Voltage-phase-frequency
A = 460V-3ph-60Hz
C = 208V-3ph-60Hz
M = 380/415-3ph-50Hz
164
–
*
Revision
level
Place holder
Specifications and Model Number Nomenclature
NOTES
165
Ensuring The High Availability
Of Mission-Critical Data And Applications.
Emerson Network Power, a business of Emerson (NYSE:EMR),
is the global leader in enabling Business-Critical Continuity™
from grid to chip for telecommunication networks, data centers,
health care and industrial facilities. Emerson Network Power
provides innovative solutions and expertise in areas including
AC and DC power and precision cooling systems, embedded
computing and power, integrated racks and enclosures,
power switching and controls, infrastructure management,
and connectivity. All solutions are supported globally by local
Emerson Network Power service technicians. Liebert AC power,
precision cooling and monitoring products and services
from Emerson Network Power deliver Efficiency Without
Compromise™ by helping customers optimize their data center
infrastructure to reduce costs and deliver high availability.
Technical Support / Service
Web Site
www.liebert.com
Monitoring
liebert.monitoring@emerson.com
800-222-5877
Outside North America: +00800 1155 4499
Single-Phase UPS & Server Cabinets
liebert.upstech@emerson.com
800-222-5877
Outside North America: +00800 1155 4499
Three-Phase UPS & Power Systems
800-543-2378
Outside North America: 614-841-6598
Environmental Systems
800-543-2778
Outside the United States: 614-888-0246
Locations
United States
1050 Dearborn Drive
P.O. Box 29186
Columbus, OH 43229
Europe
Via Leonardo Da Vinci 8
Zona Industriale Tognana
35028 Piove Di Sacco (PD) Italy
+39 049 9719 111
Fax: +39 049 5841 257
Asia
29/F, The Orient Square Building
F. Ortigas Jr. Road, Ortigas Center
Pasig City 1605
Philippines
+63 2 687 6615
Fax: +63 2 730 9572
While every precaution has been taken to ensure the accuracy
and completeness of this literature, Liebert Corporation assumes no
responsibility and disclaims all liability for damages resulting from use of
this information or for any errors or omissions.
© 2006 Liebert Corporation
All rights reserved throughout the world. Specifications subject to change
without notice.
® Liebert is a registered trademark of Liebert Corporation.
All names referred to are trademarks
or registered trademarks of their respective owners.
SL-16655_REV12_01-12
Emerson Network Power.
The global leader in enabling Business-Critical Continuity™
AC Power
Connectivity
Embedded Computing
Embedded Power
DC Power
Infrastructure Management & Monitoring
Outside Plant
Power Switching & Controls
Precision Cooling
EmersonNetworkPower.com
Racks & Integrated Cabinets
Services
Surge Protection
Emerson, Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks of Emerson Electric Co. or one of its affiliated companies.
©2006 Emerson Electric Co.