Motorola H670 - Headset - Over-the-ear User`s guide

motorola
Bluetooth
Handsfree Headset
BEFORE YOU BEGIN
®
Before using this product, read the Important Safety and Legal
Information pamphlet and follow its instructions.
Take a moment before you get started to
familiarize yourself with your new
H670 Headset.
Call Button/
Slide Switch
Multi-Color
Indicator Light
Volume
Buttons
Microphone
H670
1
Speaker
(on reverse
side)
Get connected in 4 quick steps.
CHARGE
Your Headset's Battery
Charging
Port
1 Verify slide switch is in the off position (toward
the charging port).
2 Plug the Motorola charger into the end of the
headset.
The indicator light turns red when the battery is
charging. It may take up to 1 minute for the
indicator light to turn on. When the headset's
battery is fully charged (about 2 hours), the
indicator light turns off.
3 Disconnect the charger.
Note: Headset is not functional while charging.
Note: For optimal performance, make sure that the
headset is off while charging.
2
START BLUETOOTH
FEATURE
Your Phone
Your phone's Bluetooth feature is off by default.
To use your headset, you must turn on the
Bluetooth feature in your phone.
For most Motorola phones (at the main menu):
1 Press M (Menu ) > Settings > Connection >
Bluetooth Link > Setup.
2 Scroll to Power.
3 Select Change.
4 Scroll to On.
5 Press Select to turn on the Bluetooth
feature. The Bluetooth feature remains on
until you turn the feature off.
Note: These steps are for most Motorola phones.
For other phones, see your phone's user's guide.
3
PAIR
Your Headset
Before you can use your headset, you must pair
(link) it with your phone.
Step A - ENSURE HEADSET IS IN PAIRING
MODE
Power on headset by sliding the Call button
towards the microphone to initiate easy
pairing. After a few moments, the indicator
light will be steadily lit in blue to indicate
headset is in pairing mode.
www.hellomoto.com
1-877-MOTOBLU
1-888-390-6456 (TTY/TDD United States for
hearing impaired)
Guide Number: 6809504A20-B
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. The use of wireless devices and their
accessories may be prohibited or restricted in certain areas.
Always obey the laws and regulations on the use of these
products. The Bluetooth trademarks are owned by their
proprietor and used by Motorola, Inc. under license. All other
product or service names are the property of their respective
owners.
Indicator Light
(steadily blue
for pairing mode)
If the headset does not enter pairing mode,
see TROUBLESHOOTING for help.
3
Motorola, Inc.
Consumer Advocacy Office
1307 East Algonquin Road
Schaumburg, IL 60196
PAIR CONTINUED
Your Phone
Step B - SET YOUR PHONE TO LOOK FOR
YOUR HEADSET
For most Motorola phones:
1 On your Motorola phone, press M (Menu ) >
© Motorola, Inc. 2007.
4
TEST AND USE
Your phone and headset are now paired and
ready to make and receive calls.
To make a call:
1 Place the headset over your ear.
Settings > Connection > Bluetooth Link >
Handsfree > Look for Devices.
2 On the phone, dial the number you want to
The phone lists Bluetooth devices it finds.
3 If your phone and headset are successfully
2 Select Motorola H670.
3 Select OK or Yes to pair your headset with
your phone.
4 Enter the passkey: 0000
5 Select OK.
When your headset successfully pairs and
connects with your phone, the indicator light
changes from steadily lit to flashing blue.
Note: These steps are for most Motorola phones.
For other phones, see your phone's user's guide.
call and press SEND key on your phone.
paired, you will hear ringing on the headset.
After you have successfully paired your
phone and headset, you don't need to
repeat these steps. For daily use, ensure
that your headset is turned ON and that
your phone's Bluetooth feature is ON.
To save battery power, turn OFF the
headset when you don't use it for an
extended time by sliding the switch
towards the charging plug.
USING YOUR H670
See
Features and
Functions Guide
on the reverse side
for information on
using your H670
Note: If desired, your headset can be restored to original
factory settings. This action will erase all pairing information
stored in your headset. Thus, you will need to pair your
phone and headset again (see step 3).
To restore your headset to original factory settings, press
and hold both Volume buttons and the Call button at the
same time for 10 seconds.
Features and
Functions Guide
H670
Bluetooth®
Handsfree Headset
IMPORTANT:
Be sure to first follow the
Quick Start Guide
on the reverse side
of this guide
to complete initial setup
of your H670.
TROUBLESHOOTING
My headset will not enter pairing mode.
Make sure that any devices previously paired
with the headset are turned off. If the indicator
light is not steadily lit in blue, turn off both the
other device and headset, wait 10 seconds,
then turn headset back on. Wait for the indicator
light to become steadily lit in blue, indicating
the headset is now in pairing mode.
My phone doesn't find my headset.
Make sure the indicator light on your headset is
on (lit in blue) and steady when your phone is
searching for devices (see step 3).
My headset worked before but now it's not
working.
Make sure your phone is on and the Bluetooth
feature is turned on in your phone (see step 2).
If the Bluetooth feature was turned off or was
turned on only temporarily, you may need to
restart the Bluetooth feature (see step 2) and
pair your phone and headset again (see step 3).
Support.
If you need more help, contact us at
1-877-MOTOBLU or visit us at
www.hellomoto.com/Bluetoothsupport
TURNING HEADSET
ON AND OFF
To turn your headset on, slide the switch
toward the microphone. The indicator light is
steadily purple for several seconds, then
flashes blue (if paired and connected with
another device) or is steadily blue (if ready
to be paired).
To turn your headset off, slide the switch
toward the charging plug. The indicator light
will turn off.
Slide Switch
Indicator Light
EARHOOKS AND YOUR
HEADSET
Your H670 headset is supplied with multiple
earhooks. The earhook is attached onto a hinge pin,
and is placed onto your ear when using your
headset. To install an earhook on your headset:
1 Open the attached
Once you have attached your desired
earhook, follow these steps to wear your
headset on your ear:
1 Open the attached
1
earhook 45 degrees from
the headset.
earhook 90 degrees from
the headset.
2 Loop the earhook over
2 Gently lift and pull the
top of the earhook up
and off the upper hinge
pin. Then, pull it away to
remove it.
WEARING THE
HEADSET
your ear.
1 Open Earhook
2 Pull Earhook Up
3 Position the headset for
Hinge Pin
right or left ear use (right
ear use is displayed).
3 Press earhook to your ear.
2
When worn, your headset
will look like this on your
head:
3
4 Hook the bottom of the
earhook onto the lower
hinge pin, then lift and pull
the top of the earhook
over the upper hinge pin.
CHANGING VOLUME
BUTTON ORIENTATION
You can also change the orientation of the
volume buttons on your headset.
European Union Directives
Conformance Statement
Hereby, Motorola declares that this
product is in compliance with:
1 Turn the headset power off.
• The essential requirements and
other relevant provisions of Directive
1999/5/EC.
2 Press and hold the Volume button you
• All other relevant EU Directives.
want to assign as the "volume up" button
and slide the switch toward the
microphone. The indicator light is either
steadily lit or flashing in blue.
Volume
Buttons
Product
Approval
Number
The above gives an example of a typical Product
Approval Number.
Slide
Switch
You can view your product’s Declaration of Conformity
(DoC) to Directive 1999/5/EC (to R&TTE Directive) at
www.motorola.com/rtte. To find your DoC, enter the
product Approval Number from your product’s label in
the “Search” bar on the web site.
MAKING CALLS
MAKING CALLS CONTINUED
Function
Action
Function
Action
Receive a call
Tap the Call button
Tap the Call button
Mute or unmute a call
Tap both Volume
buttons
Answer a second
incoming call
End an active call and
resume a call on hold
Tap the Call button
Disable the
indicator light
First slide the switch
toward charging plug
(to turn headset off),
then press and hold
both Volume
buttons AND slide
the switch towards
the microphone (to
turn headset on)
Reject a call
Press and hold a
Volume button until
you hear two
descending tones
End a call
Tap the Call button
Redial last call
Press and hold the
Call button until you
hear two ascending
tones
Make a voice dial call
Tap the Call button
and speak the
name after the tone
Note: Some features are phone/network dependent.
Note: Your H670 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which
profile your phone supports. See your phone's user's guide
for more information.
INDICATOR LIGHTS
With the Charger Plugged In
Headset Indicator
Headset Status
Steady red
Charging
Off
Charging complete
With No Charger Plugged In
Headset Indicator
Headset Status
Off
Power off
Steady purple
Powering up
Steady blue
Pairing/connection
mode
10 rapid purple flashes
Connection successful
Slow blue flash
Standby (not on call)
Quick blue flash
Incoming call
Slow blue pulse
Connected (on a call)
Slow purple pulse
Connected
(on a muted call)
Red flash
Idle (not connected)
Quick red flash
Low battery
Note: After 30 minutes of inactivity, the light stops flashing to
conserve power, but the headset remains in standby mode.
AUDIO TONES
Audio Tone
Ring tone
Single high tone
High to low tone
Single high tone when
pressing volume button
Two ascending tones
Two descending tones
l Low to high tone
No audio indications;
deteriorating quality
Two tones
repeated every 30 sec.
Headset Status
Incoming call
Phone network not
available
End call
Volume at minimum
or maximum
Mute enabled
Mute disabled
Connection
confirmation/voice
activation
Out of range
Low battery