Carrier 58MXB Instruction manual

58MXB
Deluxe 4---Way
Multipoise Fixed---Capacity
Condensing Gas Furnace
Service and Maintenance Instructions
For Sizes 040-- 120, Series 110 & 120
NOTE: Read the entire instruction manual before starting the
installation.
TABLE OF CONTENTS
PAGE
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . 1
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS . . . 2
CARE AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . 3
Cleaning and/or Replacing Air Filter . . . . . . . . . . . . . . . . . . . . 3
Blower Motor and Wheel Maintenance . . . . . . . . . . . . . . . . . . 5
Cleaning Burners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Cleaning Heat Exchangers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SAFETY CONSIDERATIONS
Recognize safety information. This is the safety--alert symbol
.
When you see this symbol on the furnace and in instructions or
manuals, be alert to the potential for personal injury.
Understand the signal words DANGER, WARNING, and
CAUTION. These words are used with the safety--alert symbol.
DANGER identifies the most serious hazards which will result in
severe personal injury or death. WARNING signifies a hazard
which could result in personal injury or death. CAUTION is used
to identify unsafe practices which may result in minor personal
injury or product and property damage. NOTE is used to highlight
suggestions which will result in enhanced installation, reliability, or
operation.
Installing and servicing heating equipment can be hazardous due to
gas and electrical components. Only trained and qualified service
agency personnel should install, repair, or service heating
equipment.
Primary Heat Exchangers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
!
Secondary Heat Exchangers . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Flushing Collector Box and Drainage System . . . . . . . . . . . . . 8
ELECTRICAL SHOCK, FIRE, OR EXPLOSION
HAZARD
Servicing Hot Surface Igniter . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Electrical Controls and Wiring . . . . . . . . . . . . . . . . . . . . . . . . 11
Failure to follow this warning could result in possible
damage to this equipment, personal injury, or death.
Checking Heat Tape Operation (If Applicable) . . . . . . . . . . . 11
The ability to properly perform maintenance on this
equipment requires certain expertise, mechanical skills,
tools, and equipment. If you do not possess these, do not
attempt to perform any maintenance on this equipment
other than those procedures recommended in the User’s
Manual.
Winterizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Status Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Component Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
!
WARNING
!
WARNING
WARNING
FIRE OR EXPLOSION HAZARD
EXPLOSION
Failure to follow this warning could property damage,
personal injury, or death.
Failure to follow safety warnings exactly could result in
dangerous operation, personal injury, death, or property
damage.
Never store anything on, near, or in contact with the furnace,
such as:
1. Spray or aerosol cans, rags, brooms, dust mops, vacuum
cleaners, or other cleaning tools.
2. Soap powders, bleaches, waxes or other cleaning
compounds, plastic or plastic containers, gasoline, kerosene,
cigarette lighter fluid, dry cleaning fluids, or other volatile
fluids.
3. Paint thinners and other painting compounds, paper bags,
or other paper products.
ELECTRICAL
HAZARD
SHOCK,
FIRE,
OR
-- Before servicing, disconnect all electrical power to furnace.
-- When servicing controls, label all wires prior to
disconnecting. Reconnect wires correctly.
-- Verify proper operation after servicing.
1
CAUTION
!
UNIT DAMAGE HAZARD
¤
Failure to follow this caution may result in damage to
furnace.
¤
¥¥¥¥¥
U L T R A
G A S
H I G H
Label all wires prior to disconnection when servicing
controls. Wiring errors can cause improper and dangerous
operation.
C Y
E F F I C I E N
C E
F U R N A N
GENERAL
58MXB
This furnace can be installed as a direct vent (2--pipe) or non--direct
vent (1--pipe) condensing gas furnace. These instructions are
written as if the furnace is installed in an upflow application. An
upflow furnace application is where the blower is located below
the combustion and controls section of the furnace, and
conditioned air is discharged upward. Since this furnace can be
installed in any of the 4 positions shown in Fig. 2, you may need to
revise your orientation to component location accordingly.
AIRFLOW
A05079
Fig. 1 -- Furnace in Upflow Orientation
UPFLOW
ama
ISO 9001:2000
HORIZONTAL
LEFT
CERTIFIED
HORIZONTAL
RIGHT
DOWNFLOW
AIRFLOW
AIRFLOW
REGISTERED
AIRFLOW
A93041
Fig. 2 -- Multipoise Orientation
Installing and servicing heating equipment can be hazardous due to
gas and electrical components. Only trained and qualified
service agency personnel should install, repair, or service
heating equipment. Untrained personnel can perform basic
maintenance functions described in User’s Information
Manual such as cleaning and replacing air filters. All other
operations must be performed by trained service personnel. When
working on heating equipment, observe precautions in the
literature, on tags, and on labels attached to or shipped with the
unit and other safety precautions that may apply.
Follow all safety codes including the National Fuel Gas Code
(NFGC) NFPA 54--2006/ANSI Z223.1--2006 in the USA, CSA
B149.1--05 National Standard of Canada, Natural Gas and Propane
Installation Codes (NSCNGPIC) in Canada, and the Installation
Standards, Warm Air Heating and Air Conditioning Systems
(NFPA 90B) ANSI/NFPA 90B. Wear safety glasses and work
gloves. Have a fire extinguisher available during start--up and
adjustment procedures and service calls.
ELECTROSTATIC DISCHARGE (ESD)
PRECAUTIONS
!
CAUTION
UNIT DAMAGE HAZARD
Failure to follow this caution may damage furnace
components.
Electrostatic discharge can affect electronic components.
Take precautions during furnace installation and servicing
to protect the furnace electronic control. Precautions will
prevent electrostatic discharges from personnel and hand
tools which are held during the procedure. These
precautions will help to avoid exposing the control to
electrostatic discharge by putting the furnace, the control,
and the person at the same electrostatic potential.
1. Disconnect all power to the furnace. DO NOT TOUCH
THE CONTROL OR ANY WIRE CONNECTED TO THE
CONTROL PRIOR TO DISCHARGING YOUR BODY’S
ELECTROSTATIC CHARGE TO GROUND.
2
2. Firmly touch a clean, unpainted, metal surface of the
furnace chassis which is close to the control. Tools held in a
person’s hand during grounding will be satisfactorily
discharged.
3. After touching the chassis, you may proceed to service the
control or connecting wires as long as you do nothing that
recharges your body with static electricity (for example; DO
NOT move or shuffle your feet, DO NOT touch
ungrounded objects, etc.).
4. If you touch ungrounded objects (recharge your body with
static electricity), firmly touch furnace again before
touching control or wires.
5. Use this procedure for installed and uninstalled
(ungrounded) furnaces.
6. Before removing a new control from its container, discharge
your body’s electrostatic charge to ground to protect the
control from damage. If the control is to be installed in a
furnace, follow items 1 through 5 before bringing the
control or yourself into contact with the furnace. Put all
used AND new controls into containers before touching
ungrounded objects.
7. An ESD service kit (available from commercial sources)
may also be used to prevent ESD damage.
FILTER
FILTER
SUPPORT
WASHABLE FILTER OR
DISPOSABLE MEDIA FILTER
IN FILTER CABINET
A08588
Fig. 3 -- Bottom Filter Arrangement
FILTER
IN FURNACE
CARE AND MAINTENANCE
For continuing high performance and to minimize possible furnace
failure, it is essential that maintenance be performed annually.
Consult your local dealer for maintenance and maintenance
contract availability.
!
FILTER
RETAINER
WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal
injury or death.
Turn off the gas and electrical supplies to the unit before
performing any maintenance or service. Follow the
operating instructions on the label attached to the furnace.
WASHABLE FILTER OR
DISPOSABLE MEDIA
FILTER IN FILTER CABINET
A08589
Fig. 4 -- Filter Installed for Side Inlet
The minimum maintenance that should be performed on this
equipment is as follows:
1. Check and clean or replace air filter each month as needed.
2. Check blower motor and wheel for cleanliness annually.
3. Check electrical connections for tightness and controls for
proper operation each heating season. Service as necessary.
4. Check for proper condensate drainage. Clean as necessary.
5. Check for blockages in combustion--air and vent pipes
annually.
6. Check burners for cleanliness annually.
!
!
WARNING
FIRE, CARBON MONOXIDE POISONING
HAZARD
Failure to follow this warning could result in personal
injury, death or property damage.
Never operate unit without a filter or with the blower
access panel removed. Operating a unit without a filter
or with the blower access door removed could cause
damage to the furnace blower motor. Dust and lint on
internal parts of furnace can cause a loss of efficiency.
CAUTION
CUT HAZARD
Failure to follow this caution may result in personal injury.
Be careful of sharp metal edges, etc. Use care and wear
protective clothing, gloves, and safety glasses when
removing parts.
Step 1 — Cleaning and/or Replacing Air Filter
The air filter arrangement may vary depending on the application
or orientation. See Tables 1 or 2 for filter size and type
information.
NOTE: If the filter has an airflow direction arrow, the arrow must
point toward the blower.
To clean or replace filters, proceed as follows:
If filter is installed in filter cabinet adjacent to furnace:
1. Turn off electrical supply to furnace.
2. Remove filter cabinet door.
3. Slide filter out of cabinet.
3
58MXB
FILTER
RETAINER
Table 1 – Furnace Air Filter Table
FURNACE CASING WIDTH
IN (MM)
17--- 1/2 (445)
21 (533 )
24--- 1/2 (610)
FILTER QUANTITY AND SIZE *
SIDE RETURN*
BOTTOM RETURN*
IN (MM)
IN (MM)
(1) 16 x 25 x 3/4
(1) 16 x 25 x 3/4
(406 x 635 x 19)
(406 x 635 x 19)
(1) 16 x 25 x 3/4
(1) 20 x 25 x 3/4
(406 x 635 x 19)
(508 x 635 x 19)
(1) 16 x 25 x 3/4
(1) 24 x 25 x 3/4
(406 x 635 x 19)
(610 x 635 x 19)
FILTER TYPE*
3/4” (19 mm) thick washable
3/4” (19 mm) thick washable
3/4” (19 mm) thick washable
Table 2 – Air Filter Located in Filter Cabinet
58MXB
FILTER CABINET HEIGHT --- IN (MM)
16 (406)
20 (508)
24 (610)
FILTER SIZE --- IN (MM)
(1) 16 x 25 x 3/4*
(406 x 635 x 19) or
(1) 16 x 25 x 4--- 5/16
(406 x 635 x 110)
(1) 20 x 25 x 3/4*
(508 x 635 x 19) or
(1) 20 x 25 x 4--- 5/16
(508 x 635 x 110)
(1) 24 x 25 x 3/4*or
(610 x 635 x 19) or
(1) 24 x 25 x 4--- 5/16
(610 x 635 x 110)
* Filters with a side return--air may have a different filter size. Measure the filter to obtain the correct size.
4
FILTER TYPE
washable
washable
washable
10. Turn on electrical supply to furnace.
PLUG
CAP
COLLECTOR BOX
DRAIN TUBE (BLUE
& WHITE STRIPED)
COLLECTOR BOX
TUBE (PINK)
COLLECTOR BOX
TUBE (GREEN)
INDUCER HOUSING
(MOLDED) DRAIN
TUBE (BEHIND
COLLECTOR BOX
DRAIN TUBE)
COLLECTOR BOX
DRAIN TUBE (BLUE)
CONDENSATE
TRAP
FIELD-INSTALLED
FACTORY-SUPPLIED
DRAIN TUBE
COUPLING (LEFT
DRAIN OPTION)
FIELD-INSTALLED
FACTORY-SUPPLIED
DRAIN TUBE
FIELD-INSTALLED
FACTORY-SUPPLIED
1⁄2-IN. CPVC STREET
ELBOWS (2) FOR
LEFT DRAIN OPTION
FIELD-INSTALLED
FACTORY-SUPPLIED
DRAIN TUBE
COUPLING (RIGHT
DRAIN OPTION)
A05110
Fig. 5 -- Factory--Shipped Upflow Tube Configuration
(Shown with Blower Access Panel Removed)
4. Furnaces with a washable filter, clean filter by spraying cold
tap water through filter in opposite direction of airflow.
Rinse filter and let dry. Oiling or coating of the filter is not
recommended.
5. If equipped with factory specified disposable media filter,
replace only with a factory specified media filter of the same
size.
6. Slide filter into cabinet.
7. Replace filter cabinet door.
8. Turn on electrical supply to furnace.
If filter is installed in furnace blower compartment:
1. Turn off electrical supply to furnace.
2. Remove main furnace door and blower access panel.
3. Release filter retainer wire. (See Fig. 3 or 4.)
NOTE: Filters shown in Fig. 3 and 4 can be in furnace blower
compartment or in filter cabinet, but not in both.
4. Slide filter out of furnace.
5. Furnaces with washable filter(s), clean filter by spraying
cold tap water through filter in opposite direction of airflow.
6. Rinse filter and let dry. Oiling or coating filter is not
recommended.
7. Slide filter into furnace.
8. Recapture filter retaining wire.
9. Replace blower access panel and main furnace door.
To ensure long life, economy, and high efficiency, clean
accumulated dirt and grease from blower wheel and motor
annually.
The inducer and blower motors are pre--lubricated and require no
additional lubrication. These motors can be identified by the
absence of oil ports on each end of the motor.
The following items should be performed by a qualified service
technician.
Clean blower motor and wheel as follows:
1. Turn off electrical supply to furnace.
2. Remove main furnace door and blower access panel.
3. Disconnect wires
All factory wires can be left connected, but field thermostat
connections may need to be disconnected depending on
their length and routing.
4. Position control box, transformer, and door switch assembly
to right side of furnace casing.
5. If condensate trap is located in left-- or right--hand side of
furnace casing, proceed to item 6. Otherwise remove trap
and tubing as described below (See Fig. 5.):
a. Disconnect field drain connection from condensate trap.
b. Disconnect drain and relief port tubes from condensate
trap.
c. Remove condensate trap from blower shelf.
6. Remove screws securing blower assembly to blower shelf
and slide blower assembly out of furnace. Detach ground
wire and disconnect blower motor harness plugs from
blower motor.
NOTE: Blower wheel is fragile. Use care.
7. Clean blower wheel and motor by using a vacuum with soft
brush attachment. Be careful not to disturb balance weights
(clips) on blower wheel vanes. Do not bend wheel or blades
as balance will be affected.
8. If greasy residue is present on blower wheel, remove wheel
from the blower housing and wash it with an appropriate
degreaser. To remove wheel:
a. Mark blower wheel location on shaft before disassembly
to ensure proper reassembly.
b. Loosen setscrew holding blower wheel on motor shaft.
NOTE: Mark blower mounting arms and blower housing so each
arm is positioned at the same hole location during reassembly.
c. Mark blower wheel orientation and cutoff plate location
to ensure proper reassembly.
d. Remove screws securing cutoff plate and remove cutoff
plate from housing.
e. Remove bolts holding motor mounts to blower housing
and slide motor and mounts out of housing.
f. Remove blower wheel from housing.
!
CAUTION
UNIT DAMAGE HAZARD
Failure to follow this caution may result in noise or furnace
component failure.
The blower wheel should not be dropped or bent as balance
will be affected.
g. Clean wheel per instructions on degreaser cleaner. Do
not get degreaser in motor.
5
58MXB
Step 2 — Blower Motor and Wheel Maintenance
58MXB
9. Reassemble motor and blower wheel by reversing items 8b
through 8f. Ensure wheel is positioned for proper rotation.
NOTE: Be sure to attach ground wire to blower housing.
10. Reinstall blower assembly in furnace.
11. Reinstall condensate trap and tubing if previously removed.
a. Reinstall condensate trap in hole in blower shelf.
b. Connect condensate trap drain tubes. See Fig. 5 or
tubing diagram on main furnace door for proper tube
location.
NOTE: Ensure tubes are not kinked or pinched, as this will affect
operation.
(1.) Connect 1 tube (blue or blue and white striped)
from collector box.
(2.) Connect 1 tube (violet or unmarked) from inducer
housing.
(3.) Connect 1 tube (relief port, green or pink) from
collector box.
c. Connect field drain to condensate trap.
NOTE: Ensure tubes are not kinked or pinched, as this will affect
operation.
12. Reinstall control box, transformer, and door switch
assembly on blower shelf.
13. Reconnect wires. Refer to furnace wiring diagram and
connect thermostat leads if previously disconnected. (See
Fig. 21.)
NOTE: Refer to Table 3 for motor speed lead reconnection if
leads were not identified before disconnection.
!
CAUTION
UNIT DAMAGE HAZARD
Failure to adjust the heating speed may shorten heat
exchanger life.
Heating speed selection MUST be adjusted to provide
proper temperature rise as specified on the rating plate.
15. If furnace is operating properly, release blower access panel
door switch, replace blower access panel, and replace main
furnace door.
CELL
PANEL
MANIFOLD
MOUNTING
SCREWS
GASKET
MANIFOLD
GAS VALVE
REGULATOR
FITTING
GAS
CONTROL
VALVE
A02312
Fig. 6 -- Burner Box Assembly
Step 3 — Cleaning Burners
The following items should be performed by a qualified service
technician. If the burners develop an accumulation of light dirt or
dust, they may be cleaned by using the following procedure:
1. Turn off gas and electrical supplies to furnace.
2. Remove main furnace door.
3. Remove burner box cover.
4. Using backup wrench, disconnect gas supply pipe from
furnace gas control valve.
!
CAUTION
UNIT DAMAGE HAZARD
Table 3 – Speed Selection
COLOR
SPEED
Black
Yellow (When Present)
Blue
Red
White
High
Medium High
Medium Low
Low
Common
!
FACTORY
ATTACHED TO
Cool
Spare
Heat
Fan
Com
WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal
injury or death.
Blower access panel door switch opens 115--v power to
furnace control. No component operation can occur.
Caution must be taken when manually closing this
switch for service purposes.
14. Turn on electrical supply. Manually close blower access
panel door switch. Use a piece of tape to hold switch closed.
Check for proper rotation and speed changes between
heating and cooling by jumpering R to G and R to Y/Y2 on
furnace control thermostat terminals. (See Fig. 15.)
Failure to follow this caution may result in furnace
component damage.
Label all wires prior to disconnection when servicing
controls. Wiring errors can cause improper and dangerous
operation.
5. Remove wires from gas valve. Note location for reassembly.
6. Remove burner box pressure tube from gas valve regulator
fitting.
7. Unplug igniter from harness.
8. Remove igniter leads from slot in manifold grommet.
9. Remove screws that secure manifold to burner box. (See
Fig. 6.)
NOTE: Do not remove burner box from cell panel.
10. Remove manifold, orifices, and gas valve as 1 assembly.
11. Remove screws attaching burner assembly in burner box.
NOTE: Use care when removing and reinstalling burners not to
strike the hot surface igniter.
6
!
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow this warning could result in personal
injury, death or property damage.
Never test for gas leaks with an open flame. Use a
commercially available soap solution made specifically
for the detection of leaks to check all connections.
21. Check for gas leaks.
22. Replace main furnace door.
The following items should be performed by a qualified service
technician.
Primary Heat Exchangers
IGNITER WIRES MUST
BE PLACED IN THIS SLOT
A05074
Fig. 7 -- Igniter Wire Placement
12. Remove burner assembly from burner box.
NOTE: All burners are attached to burner bracket and can be
removed as 1 assembly.
13. Clean burners with soft brush and vacuum.
14. Reinstall manifold, orifice, and gas valve assembly in
burner box. Ensure manifold seal grommet is installed
properly and burners fit over orifices.
15. Reinsert the igniter wires in the slot in the manifold
grommet, dressing the wires to ensure there is no tension on
the igniter itself. (See Fig. 7.)
!
If the heat exchangers get an accumulation of light dirt or dust on
the inside, they may be cleaned by the following procedure:
NOTE: If the heat exchangers get a heavy accumulation of soot
and carbon, both the primary and secondary heat exchangers
should be replaced rather than trying to clean them thoroughly due
to their intricate design. A build--up of soot and carbon indicates
that a problem exists which needs to be corrected, such as improper
adjustment of manifold pressure, insufficient or poor quality
combustion air, improper vent termination, incorrect size or
damaged manifold orifice(s), improper gas, or a restricted heat
exchanger (primary or secondary). Action must be taken to correct
the problem.
1. Turn off gas and electrical supplies to furnace.
2. Remove main furnace door.
!
WARNING
UNIT DAMAGE HAZARD
Failure to follow this caution may result in furnace
component damage.
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal
injury or death.
Label all wires prior to disconnection when servicing
controls. Wiring errors can cause improper and hazardous
operation.
Igniter wires must be securely placed in slot in manifold
grommet or else they could become pinched or severed
and electrically shorted.
16. Reconnect wires to gas valve and igniter. Refer to furnace
wiring diagram for proper wire location.
17. Reinstall burner box pressure tube to gas valve regulator
fitting.
18. Reinstall gas supply pipe to furnace gas control valve using
backup wrench on gas valve to prevent rotation and
improper orientation.
NOTE: Use propane gas resistant pipe dope to prevent gas leaks.
DO NOT use Teflon tape.
!
WARNING
FIRE, EXPLOSION, UNIT DAMAGE HAZARD
Failure to follow this warning could result in personal
injury, death, or property damage.
Gas valve switch MUST be facing forward or tilted
slightly.
19. Replace burner box cover.
20. Turn on gas and electrical supplies to furnace.
CAUTION
3. Disconnect wires or connectors to flame rollout switch, gas
valve, igniter, and flame sensor.
4. Disconnect combustion--air intake pipe from intake
housing.
5. Remove the pressure switch tube from intake housing.
6. Remove screws attaching intake housing to burner box, and
rotate intake housing away from burner box for removal.
7. Using backup wrench, disconnect gas supply pipe from
furnace gas control valve.
8. Disconnect pressure tubing from gas valve.
9. Remove 2 screws attaching top filler panel and rotate
upwards to gain access to screws attaching burner box to
cell panel.
10. Remove screws attaching burner box to cell panel. (See Fig.
6.)
NOTE: Burner box, cover, manifold, gas valve, and burner
assembly should be removed as 1 assembly.
11. Clean heat exchanger openings with a vacuum and a soft
brush. (See Fig. 8.)
NOTE: After cleaning, inspect the heat exchangers to ensure they
are free of all foreign objects that may restrict flow of combustion
products.
7
58MXB
Step 4 — Cleaning Heat Exchangers
PRIMARY HX
INLET OPENINGS
!
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow this warning could result in personal
injury, death or property damage.
Never test for gas leaks with an open flame. Use a
commercially available soap solution made specifically
for the detection of leaks to check all connections.
18. Replace main furnace door.
Secondary Heat Exchangers
58MXB
NOTE: The condensing side (inside) of the secondary heat
exchangers CANNOT be serviced or inspected. A small number of
bottom outlet openings can be inspected by removing the inducer
assembly. See Flushing Collector Box and Drainage System
section for details on removing inducer assembly.
A96305
Fig. 8 -- Cleaning Inlet Openings of Primary
Heat Exchangers
!
Step 5 — Flushing Collector Box and Drainage
System
1. Turn off gas and electrical supplies to furnace.
2. Remove main furnace door.
3. Disconnect inducer motor and pressure switch wires or
connectors.
4. Disconnect pressure switch tubes.
5. Disconnect vent pipe from inducer housing outlet by
loosening coupling clamp on inducer outlet.
CAUTION
UNIT MAY NOT OPERATE
Failure to follow this caution may result in improper or
intermittent unit operation.
The ground wire from the gas valve MUST be attached to
the burner box attachment screw.
12. Reverse items 3 through 10 for reassembly.
NOTE: Be sure burner box gasket is installed between burner box
and cell panel. (See Fig. 6.) If gasket is damaged, replace it.
NOTE: Inspect combustion--air intake housing. If foamed gasket
was removed, check for any damage. If gasket is damaged in any
way, it must be repaired. To repair, remove damaged gasket
section, apply sealant releasing agent such as PAM cooking spray
or equivalent (must not contain corn nor canola oil, halogenated
hydrocarbons nor aromatic content, to prevent inadequate seal
from occurring) to burner box and apply a small bead of G.E. RTV
162, G.E. RTV 6702, or Dow--Corning RTV 738 sealant to edge
of combustion--air intake housing. (See Fig. 9.)
13. Refer to furnace wiring diagram and reconnect wires to
flame rollout switch, gas valve, igniter, and flame sensor.
14. Reconnect pressure switch tubes to gas valve and intake
housing. Refer to tube routing label on main furnace door
for proper tube location. (See Fig. 10.) Be sure tubes are not
kinked.
15. Turn on gas and electrical supplies to furnace.
16. Check furnace operation through 2 complete heat operating
cycles. Look through sight glass in burner enclosure to
check burners. Burner flames should be clear blue, almost
transparent. (See Fig. 11.)
17. Check for gas leaks.
RTV
PAM
A93087
Fig. 9 -- Combustion--Air Intake Housing
Gasket Repair
6. Disconnect drain tube from inducer housing. (See Fig. 10.)
NOTE: Ensure the drain tube disconnected from the inducer
housing is higher than the collector box opening or water will flow
out of tube.
7. Remove inducer housing assembly by removing 4 bolts
attaching assembly to cell panel.
8. Flush inside of collector box with water until discharge
from condensate trap is clean and runs freely.
9. Inspect inside area of collector box for any pieces of foreign
materials and remove them if present.
!
CAUTION
UNIT DAMAGE HAZARD
Failure to follow this caution may result in furnace
component damage.
DO NOT use wire brush or other sharp object to inspect or
dislodge materials in secondary heat exchangers as cutting
of the secondary heat exchanger protective coating may
occur. Flush with water only.
8
TUBE ROUTING
Furnace is shipped from factory in upflow configuration. Pressure tube and drain tube routing MUST match the diagrams below.
Tube location when used in UPFLOW application
CAP
CAP
COLLECTOR BOX TUBE
(PINK)
PLUG
COLLECTOR BOX TUBE
(GREEN)
COLLECTOR BOX DRAIN
TUBE
(BLUE & WHITE STRIPED)
INDUCER HOUSING (MOLDED) DRAIN TUBE
(BEHIND COLLECTOR BOX DRAIN TUBE)
CONDENSATE TRAP
COLLECTOR BOX DRAIN TUBE
(BLUE)
CONDENSATE TRAP
INDUCER HOUSING DRAIN TUBE
(VIOLET)
Tube location when used in DOWNFLOW application
PLUG
CAP
COLLECTOR BOX DRAIN TUBE
(BLUE)
COLLECTOR BOX DRAIN
TUBE
(BLUE & WHITE STRIPED)
COLLECTOR BOX
TUBE (GREEN)
COLLECTOR BOX TUBE
(PINK)
PLUG
COLLECTOR BOX DRAIN TUBE
(BLUE & WHITE STRIPED)
COLLECTOR BOX TUBE
(GREEN)
INDUCER HOUSING DRAIN
TUBE (VIOLET)
COLLECTOR BOX
EXTENSION TUBE
COLLECTOR BOX
EXTENSION TUBE
CONDENSATE TRAP
COLLECTOR BOX
TUBE (PINK)
BURNER ENCLOSURE PRESSURE
REFERENCE TUBE ASSEMBLY
DRAIN TUBE COUPLING
Tube location when used on
HORIZONTAL - LEFT application
CAP
COLLECTOR BOX
TUBE (GREEN)
BURNER ENCLOSURE
PRESSURE REFERENCE
TUBE ASSEMBLY
COLLECTOR BOX
DRAIN TUBE (BLUE)
CONDENSATE TRAP
DRAIN TUBE
COUPLING
GAS VALVE
COLLECTOR BOX DRAIN TUBE
(BLUE)
COLLECTOR BOX
EXTENSION DRAIN TUBE
COLLECTOR BOX TUBE (PINK)
RELOCATE TUBE BETWEEN BLOWER
SHELF AND INDUCER HOUSING FOR
040,060, AND 080 HEATING INPUT
FURNACES
COLLECTOR BOX EXTENSION TUBE
COLLECTOR BOX TUBE (PINK)
AUXILIARY "J" BOX RELOCATED HERE
PLUG
INDUCER HOUSING
DRAIN TUBE
(VIOLET)
COLLECTOR BOX
EXTENSION TUBE
CONDENSATE TRAP
Tube location when used on
HORIZONTAL - RIGHT application
COLLECTOR BOX DRAIN TUBE
(BLUE & WHITE STRIPED)
PLUG
COLLECTOR BOX EXTENSION TUBE
BURNER ENCLOSURE PRESSURE
REFERENCE TUBE ASSEMBLY
DRAIN TUBES ROUTED IN
FRONT OF GAS VALVE
INDUCER HOUSING DRAIN TUBE (VIOLET)
COLLECTOR BOX EXTENSION DRAIN TUBE
Condensate Trap on
RIGHT Side
COLLECTOR BOX
DRAIN TUBE (BLUE)
PLUGGED END
CAP
NOTE:
COLLECTOR BOX DRAIN TUBE
(BLUE & WHITE STRIPED)
COLLECTOR BOX DRAIN TUBE
(BLUE)
FIELD-INSTALLED
FACTORY-SUPPLIED 1/2-IN.
CPVC STREET ELBOWS (2)
FOR LEFT DRAIN OPTION
FIELD-INSTALLED FACTORY-SUPPLIED
DRAIN TUBE
BURNER ENCLOSURE
PRESSURE REFERENCE
TUBE ASSEMBLY
PLUG
COLLECTOR BOX TUBE
(PINK)
COLLECTOR BOX TUBE (GREEN)
FIELD-INSTALLED
FACTORY-SUPPLIED
DRAIN TUBE COUPLING
(RIGHT DRAIN OPTION)
FIELD-INSTALLED
FACTORY-SUPPLIED DRAIN TUBE
COUPLING (LEFT DRAIN OPTION)
Condensate Trap on
LEFT Side
Condensate Trap on LEFT
Side Optional
BURNER ENCLOSURE
PRESSURE REFERENCE
TUBE ASSEMBLY
58MXB
Condensate Trap; Factory Installed
in Blower Shelf
(Blower access panel removed)
CAP
BURNER ENCLOSURE
PRESSURE REFERENCE
TUBE ASSEMBLY
COLLECTOR BOX
EXTENSION TUBE
COLLECTOR BOX
TUBE (GREEN)
COLLECTOR BOX DRAIN TUBE
(BLUE AND WHITE STRIPED)
CONDENSATE TRAP
INDUCER HOUSING DRAIN TUBE (VIOLET)
1. All tubing must be connected securely and routed to avoid kinks and traps.
2. Pressure tubing must always slope away from pressure switch to collector box connection as shown.
3. HORIZONTAL-LEFT installations require the collector box pressure tube to be relocated between the inducer housing and the blower shelf to
prevent a trap. Refer to the Installation Instructions for further details.
324999-201 REV. C
A00308
Fig. 10 -- Furnace Pressure and Drain Tubing Diagram
10. Reassemble inducer assembly by reversing items 3--7.
Tighten the vent coupling clamp screw(s) to 15 in.--lb of
torque.
NOTE: If seal between the inducer housing and the collector box
is damaged in any way, it must be repaired. To repair, apply sealant
releasing agent such as PAM cooking spray or equivalent (must not
contain corn nor canola oil, halogenated hydrocarbons nor
aromatic content, to prevent inadequate seal from occurring) to
inducer housing. (See Fig. 12.) Apply a small bead of G.E. RTV
162, G.E. RTV 6702, or Dow--Corning RTV 738 sealant to groove
in collector box.
11. Refer to furnace wiring diagram and reconnect wires to
inducer motor and pressure switches or connectors.
12. Reconnect pressure tubes to pressure switches. See diagram
on main furnace door for proper location of tubes. Be sure
tubes are not kinked. (See Fig. 10.)
13. Turn on gas and electrical supplies to furnace.
14. Check furnace operation through 2 complete heat operating
cycles. Check area below inducer housing, vent pipe, and
condensate trap to ensure no condensate leaks occur. If leaks
are found, correct the problem.
15. Check for gas leaks.
!
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow this warning could result in personal
injury, death or property damage.
Never test for gas leaks with an open flame. Use a
commercially available soap solution made specifically for
the detection of leaks to check all connections.
16. Replace main furnace door.
Step 6 — Servicing Hot Surface Igniter
The igniter does NOT require annual inspection. Check igniter
resistance before removal.
1. Turn off gas and electrical supplies to furnace.
!
CAUTION
BURN HAZARD
Failure to follow this caution may result in personal injury.
Allow igniter to cool before removal. Normal operating
temperatures exceed 2000_F (1093_C).
9
58MXB
2. Remove main furnace door.
3. Disconnect igniter wire connection.
4. Check igniter resistance. Igniter resistance is affected by
temperature. Only check resistance when the igniter is at
room temperature.
a. Using an ohm meter, check resistance across both igniter leads in connector.
b. Cold reading should be between 40 ohms and 70 ohms.
5. Remove igniter assembly.
a. Remove burner box cover.
b. Remove igniter wires from slot in manifold grommet.
(See Fig. 7.)
c. Using a 1/4--in. driver, remove the single screw securing
the igniter bracket to the burner box bracket (See Fig.
13.) and carefully withdraw the igniter and bracket assembly through the front of the burner box without
striking the igniter on surrounding parts. Note that the
igniter bracket has a handle that extends to the front of
the burner box to aid in handling. (See Fig. 13.)
d. Inspect igniter for signs of damage or failure.
EXTENDED IGNITER
BRACKET HANDLE
IGNITER
BRACKET
IGNITER BRACKET
MOUNTING SCREW
9/16˝
11/16˝
A05075
;;
;;
Fig. 13 -- Igniter Bracket
!
BURNER FLAME
CAUTION
UNIT DAMAGE HAZARD
BURNER
Failure to follow this caution may result in premature
failure of the igniter.
The igniter is fragile. DO NOT allow it to hit burner box
parts while removing or replacing it.
e. If replacement is required, replace igniter on igniter
bracket and then install assembly into burner box to
avoid damage to the igniter.
6. To replace igniter and bracket assembly, reverse items 5a
through 5c.
7. Reconnect igniter wire connection and insert the igniter
wires in the slot in the manifold grommet, dressing the
igniter wires to ensure there is no tension on the igniter
itself. (See Fig.7.)
MANIFOLD
A89020
Fig. 11 -- Burner Flame
PAM
RTV
2-5/32˝
(55 mm)
A04181
Fig. 14 -- Burner Flame
!
WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal
injury or death.
Igniter wires must be securely placed in slot in manifold
grommet or else they could become pinched or severed and
electrically shorted.
A93081
Fig. 12 -- Gasket on Collector Box
10
FIELD 24-V WIRING
FIELD 115-, 208/230-, 460-V WIRING
FACTORY 24-V WIRING
FACTORY 115-V WIRING
NOTE 2
FIVE WIRE
THREE-WIRE
HEATING-ONLY
W
C
R
G
Y
THERMOSTAT
TERMINALS
FIELD-SUPPLIED
DISCONNECT
208/230- OR
460-V
THREE
PHASE
BLOWER DOOR SWITCH
W
BLK
WHT
WHT
GND
GND
115-V FIELDSUPPLIED
DISCONNECT
AUXILIARY
J-BOX
C
O
N
T
R
O
L
R
208/230-V
SINGLE
PHASE
G
COM
GND
NOTE 1
CONDENSING
UNIT
Y/Y2
24-V
TERMINAL
BLOCK
FURNACE
58MXB
BLK
TWO
WIRE
NOTES: 1. Connect Y-terminal in furnace as shown for proper blower operation.
2. Some thermostats require a "C" terminal connection as shown.
3. If any of the original wire, as supplied, must be replaced, use
same type or equivalent wire.
A99440
Fig. 15 -- Field Wiring
8. Reinstall burner box cover.
9. Turn on gas and electrical supplies to furnace.
10. Verify igniter operation by initiating control board self--test
feature or by cycling thermostat.
11. Replace main furnace door.
Step 7 — Electrical Controls and Wiring
!
WARNING
ELECTRICAL SHOCK HAZARD
wiring during installation, service, or maintenance will cause this
fuse to blow. If fuse replacement is required, use ONLY a fuse of
identical size. The furnace control LED will flash status code 24
when fuse needs to be replaced.
With power to the unit disconnected, check all electrical
connections for tightness. Tighten all screws on electrical
connections. If any smoky or burned connections are found,
disassemble the connection, clean all parts, strip wire, and
reassemble properly and securely.
Reconnect electrical supply to unit and observe unit through 1
complete operating cycle and check for proper operation.
Failure to follow this warning could result in personal
injury or death.
Step 8 — Checking Heat Tape Operation
(If Applicable)
There may be more than one electrical supply to the unit.
Check accessories and cooling unit for additional electrical
supplies.
In applications where the ambient temperature around the furnace
is 32_F (0_C) or lower, freeze protection measures are required. If
this application is where heat tape has been applied, check to
ensure it will operate when low temperatures are present.
NOTE: Heat tape, when used, should be wrapped around the
condensate drain trap and drain line. There is no need to use heat
tape within the furnace casing. Most heat tapes are temperature
activated, and it is not practical to verify the actual heating of the
tape. Check the following:
1. Check for signs of physical damage to heat tape such as
nicks, cuts, abrasions, gnawing by animals, etc.
2. Check for discolored heat tape insulation. If any damage or
discolored insulation is evident, replace heat tape.
3. Check that heat tape power supply circuit is on.
The electrical ground and polarity for 115--v wiring must be
maintained properly. Refer to Fig. 15 for field wiring information
and to Fig. 21 for unit wiring information.
NOTE: If the polarity is not correct or furnace is not properly
grounded, the STATUS LED on the furnace control will flash
rapidly and prevent the furnace from operating. The control system
also requires an earth ground for proper operation of the furnace
control and flame sensor.
The 24--v circuit contains an automotive--type, 3--amp fuse located
on the furnace control. (See Fig. 16.) Any direct shorts of the 24--v
11
TWINNING AND/OR
COMPONENT TEST
TERMINAL
BLOWER OFF-DELAY
BLOWER OFF-DELAY
DHUM
120 180
90 150
Y1
HUMIDIFIER TERMINAL
(24-VAC 0.5 AMP MAX.)
G
TEST/TWIN
TRANSFORMER 24-VAC
CONNECTIONS
PLT
COM W/W1 Y/Y2
24V
24-V THERMOSTAT
TERMINALS
R
HUM
NUETRAL BLW
STATUS CODE LED
58MXB
0.5 AMP@24VAC
3-AMP FUSE
FUSE 3-AMP
EAC-2
L2
PL1-LOW VOLTAGE MAIN
HARNESS CONNECTOR
1
115-VAC(L2)NEUTRAL
CONNECTIONS
SEC-2 SEC-1
PLT
LED OPERATION &
DIAGNOSTIC LIGHT
COOL
FAN
SPARE-1 SPARE-2
1-AMP@
EAC-1 115VAC
SPARE-1
BLOWER SPEED
SELECTION TERMINALS
SPARE-2
PR-1
L1
HEAT
COOL
HEAT
PL2
1
115 VAC (L1) LINE
VOLTAGE CONNECTION
FAN
PL2-HOT SURFACE
IGNITER & INDUCER
MOTOR CONNECTOR
EAC-1 TERMINAL
(115-VAC 1.0 AMP MAX.)
A02142
Fig. 16 -- Control Center
!
1. Turn off electrical supply to furnace.
2. Remove main furnace door.
3. Disconnect upper inducer housing drain connection cap
from inducer housing. (See Fig. 18.)
4. Connect field--supplied 1/2--in. I.D. inducer housing tube to
upper inducer housing drain connection.
5. Insert funnel in tube and pour one quart of antifreeze,
propylene glycol (RV, swimming pool antifreeze, or
equivalent) into funnel/tube until it is visible at point where
condensate enters open drain. (See Fig. 19.)
CAUTION
UNIT AND PROPERTY DAMAGE
Failure to follow this caution may result in furnace
component failures or water property damage.
If this furnace is to be operated in an unconditioned space
where the ambient temperatures may be 32_F (0_C)or
lower, freeze protection measures must be taken. See
CONDENSATE DRAIN PROTECTION section of
Installation, Start--up, and Operating Instructions. (See Fig.
17.)
!
Step 9 — Winterizing
!
CAUTION
UNIT DAMAGE HAZARD
Failure to follow this caution may result in unit component
damage.
CAUTION
Do not use ethylene glycol (Prestone II antifreeze/coolant or
equivalent automotive type).
UNIT DAMAGE HAZARD
Failure to follow this caution may result in furnace
component damage.
6. Replace drain connection cap and clamp to inducer housing.
7. Replace main furnace door.
8. Propylene glycol need not be removed before restarting
furnace.
Freezing condensate left in the furnace may damage the
furnace.
If the furnace will be off for an extended period of time in a
structure where the temperature will drop to 32_F (0_C)or below,
winterize as follows:
12
COMPONENT TEST
!
WARNING
ELECTRICAL SHOCK AND UNIT MAY NOT
OPERATE HAZARD
Failure to follow this warning could result in electrical shock,
personal injury, or death.
A07911
Fig. 17 -- Freeze Protection
WIRING DIAGRAMS
See Fig. 15, 16 and 21 for the Deluxe 4--Way Multipoise Furnace
wiring diagrams.
TROUBLESHOOTING
Use the troubleshooting guide, the status code LED on the furnace
control and the component test to isolate furnace operation
problems.
STATUS CODES
For an explanation of status codes, refer to service label located on
back of main furnace door or Fig. 20 and the Troubleshooting
Guide. The stored status code will NOT be erased from the control
memory if 115-- or 24--v power is interrupted.
NOTE: Removing the blower access door will open the blower
access door switch and terminate 115--v power to the control.
To read current status code, remove main furnace door. The status
code LED can be viewed through the sight glass on the blower
access door.
NOTE: NO thermostat signals may be present at control and all
blower off delays must be completed to view previous codes.
!
Use the Component Test to check furnace components for proper
operation. To initiate the component self--test sequence, shut off the
room thermostat or disconnect the “R” thermostat lead. Briefly
(approximately 2 sec) short the TWIN/TEST terminal to the COM
24V terminal. The status LED will turn off. The test sequence will
be as follows:
1. LED flashes last status code, or code 11, 4 times. Record
this status code for further troubleshooting.
2. The inducer will start and continue to run until test is over.
3. Hot surface igniter (HSI) is energized for 15 sec, then
de--energized.
4. Blower operates on continuous FAN speed for 10 sec, then
turns off.
5. The blower motor operates on HEATING speed for 10 sec,
then turns off.
6. The blower motor operates on COOLING speed for 10 sec,
then turns off.
7. Inducer turns off.
8. The gas valve and humidifier terminal HUM are not
energized for safety reasons.
CAUTION
UNIT DAMAGE HAZARD
Failure to follow this caution may result in damage to unit
components.
Make sure limit switch or flame rollout switch wire does
not contact any metal component, such as gas valve. If wire
is shorted, 3--amp fuse on furnace control board will open
and unit will not operate.
To retrieve previous codes, remove 1 of the red main limit or flame
rollout switch wires for 1 to 4 sec until the LED light goes out,
then reconnect it. (Do not leave red wire disconnected for longer
periods of time as the control will assume an overtemperature
condition exists and will respond with blower operation.) This
places the control in the status recall mode and displays the last
code stored in memory.
Record the code. After the last code is displayed the control will
perform the component test, and then return to normal standby
mode.
13
58MXB
Blower access panel door switch opens 115--v power to
control board. No component operation can occur. Caution
must be taken when manually closing this switch for service
purposes.
58MXB
A99118
A99119
Fig. 18 -- Inducer Housing Drain Tube
Fig. 19 -- Funnel in Drain Tube and Antifreeze
Running Through Trap
14
SERVICE
If status code recall is needed, briefly remove then reconnect one main limit wire to display
stored status code. On RED LED boards do not remove power or blower door before initiating status code recall. After one status code recall is completed component test will occur.
LED CODE
STATUS
CONTINUOUS OFF - Check for 115VAC at L1 & L2, & 24VAC at SEC-1 & SEC-2.
CONTINUOUS ON - Control has 24VAC power.
RAPID FLASHING - Line voltage (115VAC) polarity reversed. If twinned,
refer to twinning kit instructions.
EACH OF THE FOLLOWING STATUS CODES IS A TWO DIGIT NUMBER WITH THE FIRST
DIGIT DETERMINED BY THE NUMBER OF SHORT FLASHES AND THE SECOND DIGIT BY
THE NUMBER OF LONG FLASHES.
58MXB
11 NO PREVIOUS CODE - Stored status code is erased automatically after 72
hours. On RED LED boards stored status codes can also be erased when power
(115 VAC or 24 VAC) to control is interrupted.
12 BLOWER ON AFTER POWER UP (115 VAC or 24 VAC) -Blower runs for 90
seconds, if unit is powered up during a call for heat (R-W closed) or R-W opens
during blower on-delay.
13 LIMIT CIRCUIT LOCKOUT - Lockout occurs if the limit or flame rollout switch is
open longer than 3 minutes.
- Control will auto reset after three hours.
- Refer to #33.
14 IGNITION LOCKOUT - Control will auto-reset after three hours. Refer to #34.
21 GAS HEATING LOCKOUT - Control will NOT auto reset.
Check for: - Mis-wired gas valve
-Defective control (valve relay)
22 ABNORMAL FLAME-PROVING SIGNAL - Flame is proved while gas valve is
de-energized. Inducer will run until fault is cleared. Check for:
- Leaky gas valve
- Stuck-open gas valve
23 PRESSURE SWITCH DID NOT OPEN Check for:
- Obstructed pressure tubing.
- Pressure switch stuck closed.
24 SECONDARY VOLTAGE FUSE IS OPEN Check for:
- Short circuit in secondary voltage (24VAC) wiring.
31 PRESSURE SWITCH DID NOT CLOSE OR REOPENED - If open longer than
five minutes, inducer shuts off for 15 minutes before retry. Check for:
- Excessive wind - Proper vent sizing
- Defective inducer motor
- Low inducer voltage (115VAC)
- Defective pressure switch
- Inadequate combustion air supply
- Restricted vent
- Disconnected or obstructed pressure tubing
- Low inlet gas pressure (if LGPS used)
If it opens during blower on-delay period, blower will come on for the selected
blower off-delay.
33 LIMIT CIRCUIT FAULT - Indicates a limit, or flame rollout is open. Blower will
run for 4 minutes or until open switch remakes whichever is longer. If open
longer than 3 minutes, code changes to lockout #13. If open less than 3 minutes
status code #33 continues to flash until blower shuts off. Flame rollout switch
requires manual reset. Check for: - Restricted vent
- Proper vent sizing
- Loose blower wheel
- Excessive wind
- Dirty filter or restricted duct system.
- Defective blower motor or capacitor. - Defective switch or connections.
- Inadequate combustion air supply (Flame Roll-out Switch open).
34 IGNITION PROVING FAILURE - Control will try three more times before lockout
#14 occurs. If flame signal lost during blower on-delay period, blower will come
on for the selected blower off-delay. Check for: - Control ground continuity
- Flame sensor must not be grounded
- Oxide buildup on flame sensor (clean with fine steel wool).
- Proper flame sense microamps (.5 microamps D.C. min., 4.0 - 6.0 nominal).
- Gas valve defective or gas valve turned off
- Manual valve shut-off
- Defective Hot Surface Ignitor
- Low inlet gas pressure
- Inadequate flame carryover or rough ignition
- Green/Yellow wire MUST be connected to furnace sheet metal
45 CONTROL CIRCUITRY LOCKOUT Auto-reset after one hour lockout due to;
- Gas valve relay stuck open
- Flame sense circuit failure
- Software check error
Reset power to clear lockout. Replace control if status code repeats.
COMPONENT TEST
To initiate the component test sequence, shut OFF the room thermostat or disconnect
the "R" thermostat lead. Briefly short the TEST/TWIN terminal to the "Com 24V" terminal. Status LED will flash code and then turn ON the inducer motor. The inducer
motor will run for the entire component test. The hot surface ignitor, blower motor
FAN speed (AMBER LED boards only) blower motor HEAT speed, and blower motor
COOL speed will be turned ON for 10-15 seconds each. Gas Valve and Humidifier
will not be turned on.
327884-101 REV. B
A02270
Fig. 20 -- Service Label
15
L
E
G
E
N
D
Y1
R
16
Fig. 21 -- Wiring Diagram
GND
GV
GVR 1, 2
HSI
HSIR
HUM
IDM
IDR
ILK
J1
JB
LED
LGPS
LS
BFANR
BHT/CLR
BLWR
BLWM
CAP 1, 2
CPU
EAC-1
EAC-2
FRS
FSE
FU 1
FU 2
BLU
(MED LO)
PL1
RED
CAP -1
GRN/YEL
1
CONTINUOUS-FAN SELECT RELAY, SPDT
BLOWER MOTOR SPEED CHANGE RELAY, SPDT
BLOWER MOTOR RELAY, SPST-(N.O.)
BLOWER MOTOR, PERMANENT-SPLIT-CAPACITOR
CAPACITOR
MICROPROCESSOR AND CIRCUITRY
ELECTRONIC AIR CLEANER CONNECTION (115 VAC 1.0 AMP MAX.)
ELECTRONIC AIR CLEANER CONNECTION (COMMON)
FLAME ROLLOUT SW. -MANUAL RESET, SPST-(N.C.)
FLAME-PROVING ELECTRODE
FUSE, 3 AMP, AUTOMOTIVE BLADE TYPE, FACTORY INSTALLED
FUSE OR CIRCUIT BREAKER CURRENT INTERRUPT DEVICE
(FIELD INSTALLED & SUPPLIED)
EQUIPMENT GROUND
GAS VALVE-REDUNDANT
GAS VALVE RELAY, DPST-(N.O.)
HOT SURFACE IGNITER (115 VAC)
HOT SURFACE IGNITER RELAY, SPST-(N.O.)
24VAC HUMIDIFIER CONNECTION (0.5 AMP. MAX.)
INDUCED DRAFT MOTOR, PSC
INDUCED DRAFT MOTOR RELAY, SPST-(N.O.)
BLOWER ACCESS PANEL INTERLOCK SWITCH, SPST-(N.O.)
BLOWER - OFF DELAY JUMPER SELECTOR
JUNCTION BOX
LIGHT-EMITTING DIODE FOR STATUS CODES - AMBER
LOW GAS PRESSURE SWITCH, SPST-(N.O.)
LIMIT SWITCH, AUTO-RESET, SPST (N.C.)
BRN
BRN
PR1
2
PL2
GRN/YEL
YEL
WHT
RED
GRN/YEL
WHT
WHT
ORN
BLU
START
BLWM
EAC-1
L1
BLWR
OL
SPARE 2
FAN
RED (LO)
NOTE #10
YEL
(MED HI)
WHT
(COM)
SPARE 1
L2
BFANR
BLK (HI)
BHT/CLR
COOL
HEAT
LED 1
SEC-1
EAC-2
SEC-2
HUM
TEST/TWIN
1 2 3 4 5 6 7 8 9 10 11
180
Y/Y2
150
120
J1
FU1
NOTE #6
NOTE #8
90
G
Com
24V
W
DHUM
NEUTRAL
BLW
PCB
BLK
BLK
WHT
ILK
WHT (COM)
BLK
FSE
RED
ORN
PCB
PL1
PL2
PL3
PL4
PRS
TEST/TWIN
TRAN
OL
JB
BLK
1
2
3
PL4
PL3
2
1
BRN
M
OL
WHT
IDM
BRN
AUX
CAP -2
WHT
GRN/YEL
NOTE #3
C
GV
GND
BLK
WHT
FU2
PLUG RECEPTACLE
FIELD SPLICE
EQUIPMENT GROUND
FIELD EARTH GROUND
FIELD WIRING SCREW TERMINAL
CONDUCTOR ON CONTROL PCB
FIELD WIRING (24VAC)
FIELD WIRING (115VAC)
FACTORY WIRING (24VAC)
FACTORY WIRING (115VAC)
PCB CONTROL TERMINAL
UNMARKED TERMINAL
L1
NEUTRAL
FUSED OR CIRCUIT BREAKER
DISCONNECT SWITCH (WHEN REQ’D)
NOTE #2
WHT
BLK
WHT
BLK
GRN/YEL
WHT
WHT
BLK
M
YEL
AUTO-RESET INTERNAL MOTOR OVERLOAD
TEMPERATURE SWITCH (N.C.)
PRINTED CIRCUIT BOARD CONTROL
11-CIRCUIT PCB CONNECTOR
2-CIRCUIT CONNECTOR
2-CIRCUIT HSI, CONNECTOR
3-CIRCUIT IDM EXTENSION CONNECTOR
PRESSURE SWITCH, SPST-(N.O.)
COMPONENT TEST & TWIN TERMINAL
TRANSFORMER-115VAC/24VAC
JUNCTION
RED
FRS
BLU
NOTE #11
(WHEN USED)
LGPS
GRN/YEL
BLU
RED
LS
RED
PRS
TRAN
PRINTED CIRCIUT BOARD
HSI
BLOWER OFF DELAY
JUMPER SELECT
ILK
13.
14.
10.
11.
12.
1.
2.
3.
4.
5.
6.
7.
8.
9.
PCB
NOTE #5
CPU
2
1
SEC-1
GVR-2
24VAC
115VAC
NOTE #6
TRAN
PR1
PL2
PL3
GVR-1
SEC-2
HEAT
FAN
2
1
11
3
7
9
1
5
10
4
PL1
2
8
6
PL4
HSI
COM
1
2
3
IDM
FSE
M
L2
LS
EAC-2
NOTE #3
326796-101 REV. A
C
GV
(WHEN USED)
FRS
CAP - 2
AUX
OL
BLWM
NOTE #11
PRS
LGPS
M
START
CAP-1
SCHEMATIC DIAGRAM
(NATURAL GAS & PROPANE)
LO
MED LO
MED HI
HI
SPARE-1
NOTE #10
OL
HI/LO
COOL
GND
If any of the original equipment wire is replaced use wire rated for 105°C.
Use only copper wire between the disconnect switch and the furnace junction box (JB).
This wire must be connected to furnace sheet metal for control to prove flame.
Symbols are electrical representation only.
Solid lines inside PCB are printed circuit board conductors and are not included in legend.
Replace only with a 3 amp fuse.
Inducer (IDM) and blower (BLWM) motors contain internal auto-reset thermal overload switches (OL).
Neutral connections are interchangeable within the NEUTRAL connector block.
Blower motor speed selections are for average conditions, see installation instructions for details on
optimum speed selection.
YELLOW lead not on all motors.
Factory connected when LGPS is not used.
Ignition-lockout will occur after four consecutive unsuccessful trials-for-ignition. Control will
auto-reset after three hours.
Blower-on delay: gas heating 60 seconds, cooling or heat pump 2 seconds.
Blower-off delay: gas heating selections are 90, 120, 150 or 180 seconds, cooling or heat pump
90 seconds or 5 seconds when dehumidify call is active.
NOTES:
COM
G
Y1
DHUM
Y/Y2
W
R
HUM
FAN
EAC-1
HSIR
L2
FU1
TEST/TWIN
IDR
BLWR
L1
L1
EQUIPMENT GROUND
58MXB
TO 115VAC FIELD DISCONNECT
NOTE #2
PRINTED CIRCIUT BOARD
A02157
A05107
17
YES
Go to section below for the status code that
was flashed.
Determine status code. The status code is a
2 digit number with the first digit determined
by the number of short flashes and the second
digit by the number of long flashes?
YES
Is LED status light blinking ON/OFF slowly
with a combination of short and long flashes?
NO
Is LED status light blinking rapidly without a
pause?
Is LED status light on?
START
YES
NO
YES
NO
NO
YES
Replace furnace control.
Run system through a heating or cooling cycle
to check operation. Status codes are erased
after 72 hours. On RED LED boards stored
status codes can also be erased whenever
(115V or 24V) is interrupted.
YES
Does the control respond to W, Y1 (if present),
Y/Y2, and G (24V) thermostat signals?
To recall status code briefly remove and reconnect one RED wire from the Limit
Switch or Flame Rollout switch to display stored status code. On RED LED
control do not remove power or blower access panel before initiating status
code recall. You can also recall the previous status code by momentarily shorting
the TEST/TWIN terminal to Com24V terminal until the LED goes out. LED will
flash the previous status code or status code #11 (1 short and 1 long flash) if
there was no previous code. After the control repeats the code 4 times, the
control will go through a brief component test sequence. The inducer will start
and run for the entire component test. The HSI, blower motor FAN speed
(AMBER LED boards only) HEAT speed, and COOL speed will run for 10 – 15
seconds each. Gas valve and humidifier will not be turned on.
Replace transformer.
Check for correct line voltage polarity and grounding. If units are twinned, check for proper lowvoltage (24V) transformer phasing.
Was there a previous status code
other than #11?
YES
Is there 115V going to switch?
Is door switch closed?
Replace door switch.
NO
NO
Replace furnace control.
YES
Is there 24V at SEC-1 and SEC-2?
YES
Is there 115V at L1 and L2?
TROUBLESHOOTING GUIDE
YES
The thermostat is not compatible with the
furnace control. Either install a ballast resistor,
connect the Com24V thermostat terminal to
the thermostat, or replace the thermostat.
NO
Does the problem repeat when using
a jumper wire?
Disconnect all the thermostat wires from the
furnace control.
YES
Is 24V present at W, Y1 (if present), Y/Y2 or
G thermostat terminals on the furnace control?
NO
Check room thermostat or
interconnecting cable.
Close circuit breaker and go back to START.
Check for continuity in wire from circuit breaker
to furnace.
Is circuit breaker closed?
Close door switch and go back to START.
58MXB
YES
NO
NO
NO
NO
A05096
Copyright 2009 Carrier Corp. S 7310 W. Morris St. S Indianapolis, IN 46231
Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.
Printed in U.S.A.
Edition Date: 09/09
18
Catalog No: 58MXB---3SM
Replaces: 58MXB--- 2SM
24 SECONDARY VOLTAGE FUSE IS OPEN
Check for:
- Short circuit in secondary voltage (24V)
wiring including thermostat leads.
Disconnect thermostat leads to isolate
short circuit.
23 PRESSURE SWITCH DID NOT OPEN
Check for:
- Obstructed pressure tube.
- Pressure switch stuck closed.
22 ABNORMAL FLAME-PROVING SIGNAL
Flame is proved while gas valve is deenergized. Inducer will run until fault is
cleared. Check for:
- Stuck open or leaky gas valve.
21 GAS HEATING LOCKOUT – Turn off
power and wait 5 minutes to retry.
Check for:
- Stuck closed gas valve relay on control.
- Miswire or short to gas valve wire.
14 IGNITION LOCKOUT – System failed to
ignite gas and prove flame in 4 attempts.
Control will auto-reset after 3 hours.
See status code 34.
13 LIMIT CIRCUIT LOCKOUT – Lockout
occurs if the limit or flame rollout switch is
open longer than 3 minutes. Control will
auto-reset after 3 hours. See code 33.
12 BLOWER ON AFTER POWER UP –
(115V OR 24V) – Normal operation.
Blower runs for 90 seconds, if unit is
powered up during a call for heat (R-W
closed) or when (R-W opens) during the
blower on-delay period.
11 NO PREVIOUS CODE – Stored codes
are erased after 72 hours. On RED LED
boards stored status codes can also be
erased whenever power (115V or 24V)
is interrupted. Run system through a
heating or cooling cycle to check system.
34 IGNITION PROVING FAILURE – If flame
is not sensed during the trial for ignition
period, the control will repeat the ignition
NO
sequence 3 more times before lockout
#14 occurs. If flame signal is lost during
YES
the blower on-delay period, blower will
come on for the selected blower off-delay.
Check the following items first before
proceeding to the next step.
- Gas valve turned off.
- Manual shut-off valve.
- Green/Yellow wire MUST be connected
to furnace sheet metal.
- Flame sensor must not be grounded.
To determine whether the problem is in
the gas valve, igniter, or flame sensor the
system can be operated in the component
test mode to check the igniter. First
remove the R thermostat connection from
the control and initiate the component
test sequence. Does the igniter glow
orange/white by the end of the 15 second
warm-up period?
33 LIMIT CIRCUIT FAULT – Indicates the
limit or flame rollout switch is open. Blower
will run for 4 minutes or until open switch
remakes whichever is longer. If open
longer than 3 minutes, code changes to
lockout #13. If open less than 3 min.
status code #33 continues to flash until
blower shuts off. Flame rollout switch
requires manual reset. Check for:
- Dirty filter or restricted duct system.
- Loose blower wheel.
- Defective switch or connections.
- Defective blower motor or capacitor.
- Inadequate combustion air supply
(flame rollout switch open).
- Restricted vent.
- Proper vent sizing.
- Excessive wind.
- Blower motor on incorrect speed tap.
- Input rate to furnace set too high.
31 PRESSURE SWITCH DID NOT CLOSE
OR REOPENED – If open longer than 5
minutes, inducer shuts off for 15 minutes
before retry. If opens during blower ondelay period, blower will come on for the
selected blower off-delay. Check for:
- Proper vent sizing.
- Low inducer voltage (115V).
- Low inlet gas pressure (if LGPS used).
- Inadequate combustion air supply.
- Disconnected or obstructed pressure
tubing.
- Defective inducer motor.
- Defective pressure switch.
- Excessive wind.
- Restricted vent.
Fixed.
YES
Will main burners ignite and stay on?
YES
Is current near typical value?
Clean flame sensor with fine steel wool and
recheck current. Nominal current is 4.0 to 6.0
microamps.
YES
Repeat call for heat and check flame sensor
current during trial for ignition period. Is the
DC microamps below 0.5?
NO
Do the main burners stay on?
YES
Do the main burners ignite?
YES
Does gas valve open and allow gas to flow?
YES
Reconnect the R thermostat lead and set
thermostat to call for heat. Connect voltmeter
across gas valve connections. Does gas valve
receive 24V?
Unplug igniter harness from control and initiate
another component test sequence. Check
for 115V between pin 1 and NEUTRAL-L2 on
the control. Was 115V present for the 15
second period?
58MXB
NO
NO
NO
YES
NO
NO
NO
YES
NO
Replace furnace control.
Replace electrode.
Check connections and retry. If current is
near typical value (4.0-6.0 nominal) and
burners will not stay on, replace control.
Allow blower to come on and repeat test to
check for intermittent operation.
Check for:
- Inadequate flame carryover or rough
ignition.
- Low inlet gas pressure.
- Proper firing rate.
Check that all gas valves are turned on.
Replace valve.
Check connections. If OK, replace control.
Check for continuity in the harness and igniter.
Replace defective component.
Replace furnace control.
45 CONTROL CIRCUITRY LOCKOUT
Auto-reset after 1 hour lockout due to:
- Flame circuit failure.
- Gas valve relay stuck open.
- Software check error.
Reset power to clear lockout. Replace
control if code repeats.