ACCESSORY HANDSET FOR USE WITH VT20-2431/VT20-2481 MODELS
20-2420
ACCESSORY HANDSET
Introduction
EXPAND YOUR GIGAPHONE SYSTEM. YOUR 2-LINE BASE
WILL WORK WITH UP TO 8 HANDSETS!!!
IMPORTANT:
The VT20-2420 is an Accessory Handset for use with either the VT20-2431or VT202481 GIGAPHONE system. You must have one of these 2-Line models in order
to use the VT20-2420 Accessory Handset.
This manual is designed to familiarize you with the VT20-2420 Accessory Handset
setup, registration and basic functions. For detailed operational instructions, please
refer to the VT20-2431 or VT20-2481 User's Manual.
To order additional system Handsets (model# VT20-2420), battery packs, or
headsets, call VTech Communications Inc at 1-800-595-9511.
STOP!!
If you have questions about this product, or if you're having difficulty with
setup or operation, do not return your phone to the store. Call our Customer
Support Center at:
1-800-595-9511
In Canada, call
1-800-267-7377
1
Important Safety Instructions
When using your telephone equipment, basic safety precautions should always be
followed to reduce the risk of fire, electric shock and injury, including the following:
12. Unplug this product from the wall outlet and refer servicing to
VTECH under the
following conditions:
1.
2.
3.
Read and understand all instructions.
A. When the power supply cord or plug is damaged or frayed.
Follow all warnings and instructions marked on the product.
B. If liquid has been spilled into the product.
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners
or aerosol cleaners. Use a damp cloth for cleaning.
C. If the product has been exposed to rain or water.
4.
Do not use this product near water (for example, near a bath tub, kitchen sink,
or swimming pool).
5.
Do not place this product on an unstable cart, stand, or table. The product may
fall, causing serious damage to the product.
6.
Slots and openings in the cabinet and the back or bottom are provided for
ventilation. To protect it from overheating, these openings must not be blocked
by placing the product on the bed, sofa, rug, or other similar surface. This product
should never be placed near or over a radiator or heat register. This product
should not be placed in a built-in installation where proper ventilation is not
provided.
D. If the product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions,
because improper adjustment of other controls may result in damage.
E. If the product has been dropped and the cabinet has been damaged.
F. If the product exhibits a distinct change in performance.
13. Avoid using a telephone (other than a cordless type) during an electrical storm.
There may be a remote risk of electric shock from lighting.
14. Do not use the telephone to report a gas leak in the vicinity of the leak.
7.
This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply to your home,
consult your dealer or local power company.
8.
Do not allow anything to rest on the power cord. Do not locate this product where
the cord will be abused by persons walking on it.
VTECH COMMUNICATIONS INC
9.
Never push objects of any kind into this product through cabinet slots as they
may touch dangerous voltage points or short out parts that could result in a risk
of fire or electric shock. Never spill liquid of any kind on the product.
Customer Service: 1-800-595-9511. In Canada, call VTech Electronics Ltd at 1-800267-7377.
10. To reduce the risk of electric shock, do not disassemble this product, but take
it to a VTech authorized service facility. Opening or removing cabinet parts other
than specified access doors may expose you to dangerous voltages or other risks.
Incorrect reassembling can cause electric shock when the appliance is
subsequently used.
SAVE THESE INSTRUCTIONS
11. Do not overload wall outlets and extension cords as this can result in the risk
of fire or electric shock.
2
3
Getting Started
Installation of Battery Pack in Handset
Setup
Registration And Operation Of The VTECH VT20-2420
Accessory Handset
Your VTECH 2-Line GIGAPHONE system can operate up to 8 Handsets.
The VTECH accessory Handset consists of the following:
L1
4
2
GHI
7 PQRS
*
TONE
HANDSFREE
2.4GHz
ABC
3
5
JKL
6
MNO
8
TUV
9
WXYZ
OPER
#
0
3
FLASH
CLEAR
1
1
L2
OFF
FLASH
Follow the steps below:
INTERCOM/
TRANSFER
DEF
VOLUME
2
GIGA PHONE
Handset
Belt Clip
Battery Pack
1
3
OFF
FLASH
1
4
GHI
7 PQRS
*
TONE
HANDSFREE
2.4GHz
ABC
3
DEF
5
JKL
6
MNO
8
TUV
9
WXYZ
OPER
#
0
INTERCOM/
TRANSFER
VOLUME
GIGAPHONE
5
4
Place the new battery pack in the
handset with the metal contacts
aligned with the charge contacts in
the battery compartment.
3.
Replace the battery cover by sliding
it upwards.
4.
If the new battery pack is not already
charged, place the handset in the
base unit, or a remote charging
stand, and allow it to charge for 12
hours.
After initial charge, a
maintenance charge of 8 hours
should be sufficient.
Charger Unit
1.
Plug the AC power adapter into an
electrical outlet.
As you register additional Handsets to the system, they will be assigned extension
numbers in the following order: HANDSET 2, HANDSET 3, HANDSET 4, and so forth.
Remove the Handset battery cover
by pressing on the indent and sliding
downward.
3.
Whenever a Handset battery pack is installed, the Handset will automatically begin
SEARCHING FOR BASE (if previously registered), or it will prompt you to ENTER
BASE ID to register the new Handset.
Place the new battery pack in the
Handset, with the metal contacts
aligned with the charge contacts in
the battery compartment.
BEFORE USING YOUR HANDSET(S), CAREFULLY PEEL OFF THE PROTECTIVE
FILM, COVERING THE DISPLAY.
4.
Replace the battery cover by sliding
it upward.
5.
Place the Handset in the Charge
Cradle, and allow it to charge for 12
hours. After the initial charge, a
maintenance charge of 8 hours
should be sufficient.
FLASH
2
2.
The original Handset that is shipped with you 2-Line GIGAPHONE system will be
automatically registered to the Base. This Handset is HANDSET 1.
L2
CLEAR
Remove the battery cover by pressing
on the indent and sliding downward.
Setup Of The VT20-2420
Accessory Handset
2.
L1
1.
5
Registration
The Handset Layout
Enter Base ID Code
1.
1
2
3
After charging the Handset, remove it from its
Charge Cradle; the screen will display:
OK
alternating with this screen:
9
4
5
6
2.
7
*
8
4.
4
GHI
7 PQRS
Press NEW. You will now see the ENTER BASE
ID screen as described in step 1.
Find the BASE ID Code by doing the following: (the Base must be in idle (OFF)
mode)
OFF
L2
FLASH
CLEAR
1
If, after charging the Handset, you see:
MENU
3.
L1
FLASH
TONE
HANDSFREE
2.4GHz
2
ABC
3
DEF
5
JKL
6
MNO
8
TUV
9
WXYZ
OPER
#
0
INTERCOM/
TRANSFER
10
11
12
13
14
15
VOLUME
GIGAPHONE
16
A. At the Base, press MENU
B. Scroll down to DISPLAY BASE-ID
C. Press OK. The Base screen will display the 15-digit ID Code for approximately
30 seconds. Afterwards, it will return to the idle screen.
5.
Enter the 15-digit Base ID Code into the Handset; then press OK.
6.
Wait approximately 15 to 60 seconds. You
will hear confirmation beeps from the Base
and Handset. The newly registered Handset
will now assign itself the lowest handset
number not previously assigned to a different
system Handset (1 through 8).
7.
If the Handset displays REJECTED BY BASE or continues to display
SEARCHING FOR BASE for well beyond 60 seconds, try the registration process
again by repeating the above steps.
Congratulations! You can now enjoy the benefits of your 2-Line VTECH Multi-Handset
system.
6
1.
Antenna
10.
Select/OK
2.
Message Waiting Indicator
11.
Off (Clear)
3.
Earpiece
12.
Line 2 (Flash)
4.
Headset Jack (2.5mm)
13.
5.
Scroll Keys
Battery Compartment (back of
handset)
6.
Line 1 (Flash)
14.
Intercom/Transfer
7.
Dialing Keys (0-9,*,#)
15.
Volume
8.
Handsfree Speakerphone
16.
Microphone
9.
LCD Display
7
Handset Operation
Handset Indicators
Handset Icons
Icon
1
Description
2
Line In Use indicator
On steady with no number next to it when a parallel set is in use.
On steady with one or more numbers next to it, indicating which
extensions are using the line. For example, 1 12 indicates that
Handset 1 and Handset 2 are on an outside call using Line 1.
Additional Information
Your GIGAPHONE 2-Line cordless Handset is equipped with a 2.5mm Headset Jack
for use with an optional accessory Headset for hands-free operation. If you choose
to use the Headset option, you must obtain an optional accessory Headset, which is
compatible with the GIGAPHONE.
To purchase a Headset, call VTECH Customer Service at 1-800-595-9511.
Once you have a compatible 2.5mm Headset, locate the Headset Jack on the
GIGAPHONE Handset. Connect the plug on the Headset cord to the jack on the cordless
Handset. The plug should fit securely. Do not force the connection.
Operation
Intercom indicator
On steady with the extension numbers currently on an intercom call.
For example,
02 indicates that the Base and Handset 2 are on an
intercom call.
Battery indicator
Cycles (Low, Medium, and High) when Handset battery is charging.
Flashes when a low battery condition is detected.
NOTE :
Whenever a compatible Headset is
connected to the cordless Handset, the
microphone on the Handset will be muted.
This is done to limit the effect of background
noise.
L1
M
GHI
7 PQRS
*
TONE
FLASH
HANDSFREE
2
ABC
3
DEF
5
JKL
6
MNO
8
TUV
9
WXYZ
OPER
#
0
INTERCOM/
TRANSFER
Many compatible Headsets have a reversible,
monaural design. You can wear your
Headset on either ear, leaving one ear free
for room conversation.
L2
CLEAR
1
2.4GHz
H
OFF
FLASH
4
Mute indicator
On steady when the Handset microphone is muted.
VOLUME
GIGAPHONE
Hold indicator
On steady when the line is on hold.
R
Handset Registration indicator
On steady when a Handset is not registered, or is searching for a Base
unit.
E
Enhanced Mode indicator
On steady when active Handset is in Enhanced mode.
Belt Clip
The GIGAPHONE is also equipped with a
detachable belt clip. Align the pins on the
inside edge of the clip with the notches on
the sides of the GIGAPHONE Handset.
The belt clip should snap securely into
place. Do not force the connection.
Handset LEDs
LED
Description
Message
Waiting
• Lights to indicate that you have new messages in your voicemail.
Service must be subscribed to through your local telephone
company.
• Blinks slowly to alert you to new messages stored in your VT202481 2-Line Answering System.
8
Headset Operation
9
Maintenance
In Case Of Difficulty
Your GIGAPHONE cordless telephone contains sophisticated electronic parts, so it must
be treated with care.
If you have difficulty operating your phone, the suggestions below should solve the
problem. If you still have difficulty after trying these suggestions, call VTECH
Communications at 1-800-595-9511. In Canada, call VTECH Electronics at 1-800267-7377.
Avoid rough treatment
The Phone Doesn't Work At All
Place the Handset down gently. Save the original packing materials to protect your
telephone if you ever need to ship it.
•
•
Avoid water
•
Your telephone can be damaged if it gets wet. Do not use the Handset outdoors in
the rain, or handle it with wet hands. Do not install your Base Unit near a sink, bathtub
or shower.
•
Electrical storms
•
•
Taking Care Of Your Telephone
Make sure the Power Cord is plugged
Make sure the telephone line cord is plugged firmly into the Base Unit and the
telephone wall jack.
Make sure the batteries are properly charged. If the 'LOW BATTERY' message
is shown, the battery pack needs charging.
Is the Handset registered to the Base? See Registration.
No Dial Tone
Electrical storms can sometimes cause power surges harmful to electronic equipment.
First check all the suggestions above.
If you still don't hear a dial tone, disconnect the Base Unit from the telephone
jack and connect a different phone. If there is no dial tone on that phone either,
the problem is in your wiring or local service. Call your local telephone company.
For your own safety, use caution when using electric appliances during storms.
Cleaning your telephone
You Get Noise, Static, Or A Weak Signal Even When You're
Near The Base Unit
Your telephone has a durable plastic casing that should retain its luster for many years.
Clean it only with a soft cloth slightly dampened with water or a mild soap. Do not use
excess water or cleaning solvents of any kind.
•
Remember that electrical appliances can cause serious injury if used when you are
wet or standing in water. If your Base Unit should fall into water, DO NOT RETRIEVE
IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORDS
FROM THE WALL. Then pull the unit out by the unplugged cords.
Household appliances plugged into the same circuit as the Base Unit can
sometimes cause interference. Try moving the appliance or the Base Unit to another
outlet.
You Get Noise, Static, Or A Weak Signal When You're Away
From The Base Unit
•
•
You may be out of range. Either move closer to the Base, or relocate the Base
Unit.
The layout of your home may be limiting the range. Try moving the Base Unit
to another position.
The Handset Does Not Ring When You Receive A Call
•
•
•
10
Make sure you have the Handset ringer activated. To set the ringer, see HANDSET
SETTINGS and BASE SETTINGS.
Make sure the telephone line cord is plugged firmly into the Base Unit and the
telephone jack. Make sure the power cord is plugged in.
You may be too far from the Base Unit.
11
Warranty Statement
In Case Of Difficulty
•
You may have too many extension phones on your telephone line to allow all
of them to ring. Try unplugging some of the other phones.
You Hear Other Calls While Using Your Phone
•
Disconnect your Base Unit from the telephone jack, and plug in a regular telephone.
If you still hear other calls, the problem is probably in your wiring or local service.
Call your local telephone company.
You Hear Noise In The Handset, And None Of The Keys
Or Buttons Work
•
Make sure the power cord is plugged in.
Common Cure For Electronic Equipment
If the unit does not seem to be responding normally, then try putting the Handset in
the cradle. If it does not seem to respond, do the following (in the order listed) :
What does this limited warranty cover?
• The manufacturer of this VTECH product, VTECH Communications, warrants to the
holder of a valid proof of purchase (“Consumer” or “you”) that the product and all
accessories provided by VTECH in the sales package (“Product”) are free from material
defects in material and workmanship, pursuant to the following terms and conditions,
when installed and used normally and in accordance with operation instructions. This
limited warranty extends only to the Consumer for Products purchased and used in
the United States of America.
What will VTECH Communications do if the Product is not free from
material defects in materials and workmanship during the limited
warranty period (“Materially Defective Product”)?
• . During the limited warranty period, VTECH’s authorized service representative will
repair or replace at VTECH’s option, without charge, a Materially Defective Product.
If we repair this product, we may use new or refurbished replacement parts. If we
choose to replace this product, we may replace it with a new or refurbished product
of the same or similar design.VTECH will return repaired or replacement products
to you in working condition. VTECH will retain defective parts, modules, or equipment.
Repair or replacement of Product, at VTECH‘S option, is your exclusive remedy. You
should expect the repair or replacement to take approximately 30 days.
How Long is the limited warranty period ?
1.
Disconnect the power to the Base.
2.
Disconnect the Handset battery, and spare battery pack, if applicable.
3.
Wait a few minutes.
4.
Connect power to the Base.
5.
Re-install the battery pack(s).
What is not covered by this limited warranty ?
6.
Watch for Handset to display :
This limited warranty does not cover
1. Product that has been subjected to misuse, accident, shipping or other physical damage,
improper installation, abnormal operation or handling, neglect, inundation, fire, water
or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration or modification by anyone other
than an authorized service representative of VTECH; or
3. Product to the extent that the problem experienced is caused by signal conditions,
network reliability or cable or antenna systems; or
4. Product to the extent that the problem is caused by use with non-VTECH electrical
accessories; or
5. Product whose warranty/quality stickers, Product serial numbers plates or electronic
serial numbers have been removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair from outside the United
then
12
• The limited warranty period for the product extends for ONE(1)YEAR from the date
of purchase if we repair or replace a Materially Defective Product the terms of this
limitad warranty. this limited warranty also applies to repaired or replacement Products
for a period of either (a) 90 days from the date the repaired or replacement Product
is shipped to you or (b) the time remaining on the original one-year limited warranty.
whichever is longer.
13
Warranty Statement
Warranty Statement
States, or used for commercial or institutional purposes (including but not limited to
Products used for rental purposes ) ;or
7. Product returned without valid proof of purchase (see 2 below); or
8. Charges for installation or set up, adjustment of customer controls, and installation or
repair of systems outside the unit.
Limitations: Implied warranties, including those of fitness for a particular purpose
and merchantability (an unwritten warranty that the product is fit for ordinary use)
are limited to one year from date of purchase. Some states do not allow limitations
on how long an implied warranty lasts, so the above limitation may not apply to you.
How do you get warranty service?
• To obtain warranty service in the United States of America. call 1 800-595-9511 for
instructions regarding where to return the Product. Before calling for service, please
check the user’s manual, A check of the Product controls and features may save
you a service call.
• Except as provided by applicable law, you assume the risk of loss or damage during
transit and transportation and are responsible for delivery or handling charges incurred
in the transport of Product(s) to the service location . VTECH will return repaired
or replaced product under this limited warranty to you , transportation, delivery or
handling charges prepaid .VTECH assumes no risk for damage or loss of the Product
in transit.
• If the Product failure is not covered by this limited warranty, or proof of purchase does
not meet the terms of this limited warranty, VTECH will notify you and will request that
you authorize the cost of repair prior to any further repair activity. You must pay for
the cost of repair and return shipping costs for the repair of Products that are not covered
by this limited warranty.
• In no event shall VTECH be liable for any indirect, special, incidental, consequential,
or similar damages (including, but not limited to lost profits or revenue, inability to
use the product, or other associated equipment, the cost of substitute equipment,
and claims by third parties) resulting from the use of this product. Some states do
not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTECH
service location along with a description of the malfunction or difficulty;
2. Include “valid proof of purchase” (sales receipt) identifying the Product purchased
(Product model) and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
Other Limitations
• This warranty is the complete and exclusive agreement between you and VTECH.
It supersedes all other written or oral communications related to this Product. VTECH
provides no other warranties for this product. The warranty exclusivelydescribes all
of VTECH’s responsibilities regarding the product.
There are no other express warranties. No one is authorized to make modifications
to this limited warranty and you should not rely on any such modification.
State Law Rights: This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
14
15
FCC and IC Regulations
This equipment complies with Parts 15 of the Federal Communications Commission
(FCC) rules for the United States. It also complies with regulations RSS210 and CS03 of Industry and Science Canada. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
A label is located on the underside of the Base Unit containing either the FCC registration
number and Ringer Equivalence Number (REN) or the IC registration number and Load
Number. You must, upon request, provide this information to your local telephone
company.
This equipment is compatible with inductively coupled hearing aids.
Should you experience trouble with this telephone equipment, please contact:
VTech Communications Inc
CUSTOMER SERVICE at 1-800-595-9511. In Canada, call VTech Electronics Ltd at 1800-267-7377.
For repair/warranty information. The telephone company may ask you to disconnect
this equipment from the line network until the problem has been corrected.
FCC Part 15
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
The equipment has been tested and found to comply with part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try and correct the interference
by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet or on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
16
FCC and IC Regulations
FCC and ACTA Information
If this equipment was approved for connection to the telephone network prior to July
23,2001, it was registered with the Federal Commissions (FCC) in accordance with
Part 68 of its rules. If the equipment was approved after that date, it complies with
the Part 68 rules and with Technical Requirements for Connection of Equipment to
the Telephone Network adopted by the Administrative Council for Terminal Attachments
(ACTA). We are required to provide you with the following information.
1. Connection and use with the nationwide telephone network
The plug and jack used to connect this equipmet to the premises wiring and the telephone
network must comply with the applicable Part 68 rules and technical requirements
adopted by ACTA. A compliant telephone cord and modular plug is provided with this
product. It is designed to be connected to a compatible modular jack that is also
compliant. An RJ11 jack should normally be used for connecting to a single line and
an RJ14 jack for two lines. See Installation Instructions in the user's manual. This
equipment may not be used with Coin Telephone Lines or with Party Lines.
2. Product identifier and REN information
The label on the back or bottom of this equipment contains, among other things, an
identifier indicating product approval and the Ringer Equivalence Number (REN). This
information must be provided to your local telephone company upon request, For
equpment approved prior to July 23,2001, the product identifier is preceded by the phrase
"FCC Reg No." and the REN is listed separately. For equipment approved after that
date, the product identifier is preceded by "US" and a colon (;), and the REN is encoded
in the product identifier as the sixth and seventh characters following the colon. For
example, the product identifier US: AAAEQ03T123XYZ would indicate an REN of 0.3.
The REN is used to determine how many devices you may connect to your telephone
line and still have them ring when you are called. In most , but not all areas, the sum
of all RENS should be five (5.0) or less, You may want to connect your local telephone
company for more information.
3. Repair instructions
If the equipment is malfunctioning, it must be unplugged from the modular jack until
the problem has been corrected. Repairs to this telephone equipment can only be made
by the manufacturer or its authorized agents. For repair procedures, follow the
instructions outlined under the Limited Warranty.
4. Rights of the telephone company
If this equipment is causing harm to the telephone network, the telephone company
may temporarily discontinue your telephone service. The telephone company is required
to notify you before interrupting service. If advance notice is not practical, you will be
notified as soon as possible. You will be given the opportunity to correct the problem
and the telephone company is required to inform you of your right to file a complaint
17
FCC and IC Regulations
with the FCC. Your telephone company may make changes in facilities, equipment, operation,
or procedures that could affect the proper functioning of this product. The telephone company
is required to notify you if such changes are planned.
5. Hearing aid compatibility
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
6. Programming/testing of emergency numbers
If this product has memory dialing locations, you may choose to store police, fire department
and emergency medical service telephone number in this locations. If you do, please keep
three things in mind:
a. We recommend that you also write the telephone number on the directory card, so that
you can still dial the emergency number manually if the memory dialing feature doesn't work.
FCC and IC Regulations
Before installing this equipment, users should ensure that it is permissible to be connected
to the facilities of the local telecommunications company. The equipment must also
be installed using an acceptable method of connection. The customer should be aware
that compliance with the above conditions may not prevent degradation of services in
some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance
facility designated by the supplier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the telecommunications company
cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of
the power utility, telephone lines and internal metallic water pipe system, if present,
are connected together. This precaution may be particularly important in rural areas.
b. This feature is provided only as a convenience, and the manufacturer assumes no
responsibility for customer reliance upon the memory feature.
c. Testing the emergency telephone numbers you have stored is not recommended. However,
if you do make a call to an emergency number:
Caution :
•
Your GIGAPHONE is designed to operate at the maximum power allowed by the FCC
and IC. This means your Handset and Base Unit can communicate only over a certain
distance - which will depend on the location of the Base Unit and Handset, weather,
and the construction and layout of your home or office.
•
You must remain on the line and briefly explain the reason for the call before hanging
up.
Programming/testing of emergency numbers should be performed during off-peak hours,
such as in the early morning or late evening, when the emengency services tend to
be less busy.
Users should not attempt to make such connections themselves, but should contact
the appropriate electrical inspection authority, or electrician, as appropriate.
R
The RBRC Seal
IC (Industry Canada)
The RBRC R Seal on the nickel-cadmium battery indicates that VTech
Communications, Inc. is voluntarily participating in an industry program to
collect and recycle these batteries at the end of their useful lives, when
taken out of service within the United States and Canada.
This telephone is registered for use in Canada.
Notice :
The REN assigned to this device denotes the number of devices you may connect to the
telephone loop which is used by the device to prevent overloading The termination on a loop
may consist of any combination of devices subjected only to the requirement that the sum
of the REN does not exceed five (5.0)
The RBRC R program provides a convenient alternative to placing used
nickel-cadmium batteries into the trash or municipal waste,which may be illegal in your
area.
R
Notice :
VTech’s participation in RBRC makes it easy for you to drop off the spent battery at local
retailers participating in the RBRC program or at authorized VTech product service
centers.Please call 1-800-8-BATTERYTM for information on Ni-Cd battery recycling and
disposal bans/restrictions in your area.VTech’s involvement in this program is part of its
commitment to protecting our environment and conserving natural resources.
R
The Industry Canada label identifies certified equipment. This certification means that the
equipment meets certain telecommunications network protective, operational and safety
requirements. The Department does not guarantee the equipment will operate to the user's
satisfaction.
R
RBRC is a registered trademark of Rechargeable Battery Recycling Corporation.
18
19
Technical Specifications
FREQUENCY CONTROL
WEIGHT
Crystal controlled
PLL synthesizer
Handset :
Charger :
TRANSMIT FREQUENCY
POWER REQUIREMENTS
2401.056 - 2481.408 MHz
Handset :
2.4V 1500mAh NiMH
or 2.4V 800mAh Ni-Cd
Battery Pack
Charger :
6 VDC @ 300mA
RECEIVE FREQUENCY
2401.056 - 2481.408 MHz
CHANNELS
94 Channels
NOMINAL
RANGE
116 grams
(excluding battery pack)
200 grams
MEMORY
Speed Dial : 50 Memory locations, up to
32 digits per location.
EFFECTIVE
CID :
Maximum power allowed by FCC and IC.
Actual operating range may vary according
to environmental conditions at the time of
use.
Alphanumeric Display
50 Memory locations
SIZE
Handset : 174mm x 50mm x 34mm
(including antenna)
Charger : 60mm x 73mm x 52mm
SPECIFICATIONS
ARE
TYPICAL AND MAY CHANGE
WITHOUT NOTICE.
VTECH TELECOMMUNICATIONS LTD.
A member of THE VTECH GROUP OF COMPANIES.
Distributed in the U.S.A. by VTech Communications Inc.; Beaverton, Oregon.
Distributed in Canada by VTech Electronics Canada Ltd., Suite 200, 7671 Alderbridge
Way, Richmond, B.C. V6X 1Z9.
20
Copyright 2002 for VTECH TELECOMMUNICATIONS LTD.
Printed in China
91-5822-20-00
ISSUE 0