Mitsubishi Electric MS-GF60VA Operating instructions

SPLIT-TYPE AIR CONDITIONERS
INDOOR UNIT
MS-GF50VA
MS-GF60VA
English is original.
For user
OPERATING INSTRUCTIONS
• To use this unit correctly and safely, be sure to read these operating instructions before use.
English
Übersetzung des
Originals
For den Anwender
BEDIENUNGSANLEITUNG
• Für einen sicheren und ordnungsgemäßen Gebrauch des Geräts unbedingt diese Bedienungsanleitung vor der Inbetriebnahme durchlesen.
Deutsch
Traduction du texte
d’origine
A l’attention des clients
NOTICE D’UTILISATION
• Pour avoir la certitude d’utiliser cet appareil correctement et en toute
sécurité, veuillez lire cette notice d’instructions avant de mettre le climatiseur sous tension.
Français
Vertaling van het
origineel
Voor de klant
BEDIENINGSINSTRUCTIES
• Om dit apparaat correct en veilig te kunnen gebruiken moet u deze bedieningsinstructies voor gebruik eerst doorlezen.
Nederlands
Traducción del
original
Para los clientes
MANUAL DE INSTRUCCIONES
• Para utilizar esta unidad de forma correcta y segura, lea previamente
estas instrucciones de funcionamiento.
Español
Traduzione
dell’originale
Per gli utenti
LIBRETTO D’ISTRUZIONI
• Per utilizzare correttamente ed in tutta sicurezza questo apparecchio,
leggere il presente libretto d’istruzioni prima dell’uso.
Italiano
Μετάφραση του
αρχικού
Για το χρήστη
ΟΔΗΓΙΕΣ ΛΕΙΤΟΥΡΓΙΑΣ
• Για να χρησιμοποιήσετε αυτή τη μονάδα σωστά και με ασφάλεια, βεβαιωθείτε ότι έχετε διαβάσει αυτό το εγχειρίδιο οδηγιών πριν από τη χρήση.
Ελληνικά
Tradução do
original
Para o utilizador
INSTRUÇÕES DE OPERAÇÃO
• Para utilizar esta unidade correctamente e com segurança, certifiquese de que lê estas instruções de operação antes da utilização.
Português
Oversættelse af
den originale tekst
Til kunden
BETJENINGSVEJLEDNING
• Læs denne betjeningsvejledningen før brug, så enheden bruges korrekt
og sikkert.
Dansk
Översättning från
originalet
För användaren
BRUKSANVISNING
• Läs bruksanvisningen innan enheten tas i bruk så att den används säkert och på rätt sätt.
Svenska
Orijinalin çevirisi
Kullanıcı için
ÇALIŞTIRMA TALİMATLARI
• Bu üniteyi doğru ve güvenli bir biçimde kullanmak için, kullanmadan
önce bu işletim talimatlarını okuduğunuzdan emin olun.
Türkçe
Перевод
оригинала
SG79F572H01_Cover.indd 1
MS-GF80VA
Для пользователя
ИНСТРУКЦИИ ПО ЭКСПЛУАТАЦИИ
• В целях правильной и безопасной эксплуатации данного устройства обязательно перед его использованием прочтите настоящее
руководство по эксплуатации.
Русский
2012/12/19 9:14:20
● OPERATING INSTRUCTIONS ●
CONTENTS
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
SAFETY PRECAUTIONS
DISPOSAL
NAME OF EACH PART
PREPARATION BEFORE OPERATION
SELECTING OPERATION MODES
FAN SPEED AND AIRFLOW DIRECTION ADJUSTMENT
LONG OPERATION
POWERFUL COOL OPERATION
ECONO COOL OPERATION
TIMER OPERATION (ON/OFF TIMER)
CLEANING
WHEN YOU THINK THAT TROUBLE HAS OCCURRED
WHEN THE AIR CONDITIONER IS NOT GOING TO BE USED FOR A LONG TIME
INSTALLATION PLACE AND ELECTRICAL WORK
SPECIFICATIONS
1
2
3
3
4
5
5
5
6
6
7
8
9
9
9
SAFETY PRECAUTIONS
• Since rotating parts and parts which could cause an electric shock are used
in this product, be sure to read these “Safety Precautions” before use.
• Since the cautionary items shown here are important for safety, be sure to
observe them.
• After reading this manual, keep it together with the installation manual in a
handy place for easy reference.
Marks and their meanings
WARNING :
Incorrect handling could cause serious hazard, such as
death, serious injury, etc. with a high probability.
CAUTION :
Incorrect handling could cause serious hazard depending
on the conditions.
WARNING
Do not connect the power cord to an intermediate point, use
an extension cord, or connect multiple devices to a single
AC outlet.
• This may cause overheating, fire, or electric shock.
Make sure the power plug is free of dirt and insert it securely
into the outlet.
• A dirty plug may cause fire or electric shock.
Do not bundle, pull, damage, or modify the power cord, and do
not apply heat or place heavy objects on it.
• This may cause fire or electric shock.
Do not turn the breaker OFF/ON or disconnect/connect the
power plug during operation.
• This may create sparks, which can cause fire.
• After the indoor unit is switched OFF with the remote controller,
make sure to turn the breaker OFF or disconnect the power plug.
Do not expose your body directly to cool air for a prolonged
length of time.
• This could be detrimental to your health.
The unit should not be installed, relocated, disassembled,
altered, or repaired by the user.
• An improperly handled air conditioner may cause fire, electric
shock, injury, or water leakage, etc. Consult your dealer.
• If the power supply cord is damaged, it must be replaced by the
manufacturer or its service agent in order to avoid a hazard.
When installing, relocating, or servicing the unit, make sure
that no substance other than the specified refrigerant (R410A)
enters the refrigerant circuit.
• Any presence of foreign substance such as air can cause abnormal
pressure rise and may result in explosion or injury.
• The use of any refrigerant other than that specified for the system
will cause mechanical failure, system malfunction, or unit breakdown. In the worst case, this could lead to a serious impediment
to securing product safety.
Meanings of symbols used in this manual
: Be sure not to do.
: Be sure to follow the instruction.
: Never insert your finger or stick, etc.
: Never step onto the indoor/outdoor unit and do not put anything on them.
: Danger of electric shock. Be careful.
: Be sure to disconnect the power supply plug from the power outlet.
: Be sure to shut off the power.
Do not insert your finger, a stick, or other objects into the air
inlet or outlet.
• This may cause injury, since the fan inside rotates at high speeds
during operation.
In case of an abnormal condition (such as a burning smell),
stop the air conditioner and disconnect the power plug or turn
the breaker OFF.
• A continued operation in the abnormal state may cause a malfunction, fire, or electric shock. In this case, consult your dealer.
When the air conditioner does not cool or heat, there is a possibility of refrigerant leakage. In this case, consult your dealer.
If a repair involves recharging the unit with refrigerant, ask the
service technician for details.
• The refrigerant used in the air conditioner is safe. Normally, it does
not leak. However, if refrigerant leaks and comes in contact with
a heat source such as a fan heater, kerosene heater, or cooking
stove, it will create a harmful gas.
The user should never attempt to wash the inside of the indoor
unit. Should the inside of the unit require cleaning, contact
your dealer.
• Unsuitable detergent may cause damage to plastic material inside
the unit, which may result in water leakage. Should detergent
come in contact with electrical parts or the motor, it will result in
a malfunction, smoke, or fire.
CAUTION
Do not touch the air inlet or the aluminum fins of the indoor/
outdoor unit.
• This may cause injury.
Do not use insecticides or flammable sprays on the unit.
• This may cause a fire or deformation of the unit.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play
with the appliance.
En-1
SG79F572H01_en.indd 1
2012/12/19 9:13:05
SAFETY PRECAUTIONS
CAUTION
Do not expose pets or houseplants to direct airflow.
• This may cause injury to the pets or plants.
Do not place other electric appliances or furniture under the
indoor/outdoor unit.
• Water may drip down from the unit, which may cause damage or
malfunction.
Do not leave the unit on a damaged installation stand.
• The unit may fall and cause injury.
Do not step on an unstable bench to operate or clean the unit.
• This may cause injury if you fall down.
Do not pull the power cord.
• This may cause a portion of the core wire to break, which may
cause overheating or fire.
Do not charge or disassemble the batteries, and do not throw
them into a fire.
• This may cause the batteries to leak, or cause a fire or explosion.
Do not operate the unit for more than 4 hours at high humidity (80% RH or more) and/or with windows or outside door left
open.
• This may cause the water condensation in the air conditioner, which
may drip down, wetting or damaging the furniture.
• The water condensation in the air conditioner may contribute to
growth of fungi, such as mold.
Do not use the unit for special purposes, such as storing food,
raising animals, growing plants, or preserving precision devices
or art objects.
• This may cause deterioration of quality, or harm to animals and
plants.
Do not expose combustion appliances to direct airflow.
• This may cause incomplete combustion.
Never put batteries in your mouth for any reason to avoid accidental ingestion.
• Battery ingestion may cause choking and/or poisoning.
Before cleaning the unit, switch it OFF and disconnect the power
plug or turn the breaker OFF.
• This may cause injury, since the fan inside rotates at high speeds
during operation.
When the unit will be unused for a long time, disconnect the
power plug or turn the breaker OFF.
• The unit may accumulate dirt, which may cause overheating or
fire.
Replace all batteries of the remote controller with new ones of
the same type.
• Using an old battery together with a new one may cause overheating, leakage, or explosion.
If the battery fluid comes in contact with your skin or clothes,
wash them thoroughly with clean water.
• If the battery fluid comes in contact with your eyes, wash them
thoroughly with clean water and immediately seek medical attention.
Ensure that the area is well-ventilated when the unit is operated
together with a combustion appliance.
• Inadequate ventilation may cause oxygen starvation.
Turn the breaker OFF when you hear thunder and there is a possibility of a lightning strike.
• The unit may be damaged if lightning strikes.
After the air conditioner is used for several seasons, perform
inspection and maintenance in addition to normal cleaning.
• Dirt or dust in the unit may create an unpleasant odor, contribute
to growth of fungi, such as mold, or clog the drain passage, and
cause water to leak from the indoor unit. Consult your dealer for
inspection and maintenance, which require specialized knowledge
and skills.
Do not operate switches with wet hands.
• This may cause electric shock.
Do not clean the air conditioner with water or place an object that
contains water, such as a flower vase, on it.
• This may cause fire or electric shock.
Do not step on or place any object on the outdoor unit.
• This may cause injury if you or the object falls down.
IMPORTANT
Dirty filters cause condensation in the air conditioner which will contribute to
the growth of fungi such as mold. It is therefore recommended to clean air filters
every 2 weeks.
For installation
WARNING
Consult your dealer for installing the air conditioner.
• It should not be installed by the user since installation requires specialized
knowledge and skills. An improperly installed air conditioner may cause
water leakage, fire, or electric shock.
Provide a dedicated power supply for the air conditioner.
• A non-dedicated power supply may cause overheating or fire.
Do not install the unit where flammable gas could leak.
• If gas leaks and accumulates around the outdoor unit, it may cause an
explosion.
Earth the unit correctly.
• Do not connect the earth wire to a gas pipe, water pipe, lightning rod, or
a telephone ground wire. Improper earthing may cause electric shock.
CAUTION
Install an earth leakage breaker depending on the installation location
of the air conditioner (such as highly humid areas).
• If an earth leakage breaker is not installed, it may cause electric
shock.
Ensure that the drain water is properly drained.
• If the drain passage is improper, water may drip down from the indoor/
outdoor unit, wetting and damaging the furniture.
In case of an abnormal condition
Immediately stop operating the air conditioner and consult your dealer.
DISPOSAL
To dispose of this product, consult your dealer.
Note:
This symbol mark is for EU countries only.
This symbol mark is according to the directive 2002/96/
EC Article 10 Information for users and Annex IV, and/
or to the directive 2006/66/EC Article 20 Information for
end-users and Annex II.
Fig. 1
Your MITSUBISHI ELECTRIC product is designed and manufactured with high
quality materials and components which can be recycled and/or reused.
This symbol means that electrical and electronic equipment, batteries and
accumulators, at their end-of-life, should be disposed of separately from your
household waste.
If a chemical symbol is printed beneath the symbol (Fig. 1), this chemical symbol means that the battery or accumulator contains a heavy metal at a certain
concentration. This will be indicated as follows:
Hg: mercury (0,0005%), Cd: cadmium (0,002%), Pb: lead (0,004%)
In the European Union there are separate collection systems for used electrical
and electronic products, batteries and accumulators.
Please, dispose of this equipment, batteries and accumulators correctly at your
local community waste collection/recycling centre.
Please, help us to conserve the environment we live in!
En-2
SG79F572H01_en.indd 2
2012/12/19 9:13:07
● OPERATING INSTRUCTIONS ●
NAME OF EACH PART
Indoor unit
Remote controller
Signal transmitting
section
Distance of signal :
About 6 m
Front panel
Air filter
(Nano platinum filter)
Beep(s) is (are) heard
from the indoor unit when
the signal is received.
Operation display
section
Air cleaning filter
(Electrostatic anti-allergy
enzyme filter, option)
ON/OFF
(operate/stop)
button
Air inlet
Temperature buttons
Page 4
Operation select
button Page 4
Off-timer button Page 6
FAN speed
control button
On-timer button Page 6
Page 5
Air outlet
Heat exchanger
Horizontal vane
TIME set buttons Pages 3, 6
Increase time
Decrease time
POWERFUL
COOL
button Page 5
Display section
Operation indicator lamp
Emergency
operation switch Page 4
Remote control receiving section
Outdoor unit
WIDE VANE
button Page 5
ECONO COOL
button Page 6
LONG button Page 5
VANE control
button Page 5
CLOCK button Page 3
RESET button Page 3
Lid
Slide down
to open
Remote controller
holder
Air inlet (back and side)
Refrigerant piping
• Install the remote controller holder in a place where
the signal can be received
by the indoor unit.
Drainage hose
Air outlet
Drain outlet
Outdoor units may be different in appearance.
Only use the remote controller provided with the unit.
Do not use other remote controllers.
If two or more indoor units are installed in proximity to one another, an indoor
unit that is not intended to be operated may respond to the remote controller.
PREPARATION BEFORE OPERATION
Before operation: Insert the power supply plug into the power outlet and/or turn the breaker on.
Installing the remote controller batteries
4.
1.
Setting current time
Press RESET.
1.
Remove the front lid.
Press CLOCK.
2.
3.
Insert the negative
pole of AAA alkaline
batteries first.
Install the front lid.
• Make sure the polarity of the batteries is correct.
• Do not use manganese batteries and leaking batteries. The remote controller
could malfunction.
• Do not use rechargeable batteries.
• Replace all batteries with new ones of the same type.
• Batteries can be used for approximately 1 year. However, batteries with
expired shelf lives last shorter.
• Press RESET gently using a thin instrument.
If the RESET button is not pressed, the remote controller may not operate
correctly.
2.
3.
Press CLOCK again.
Press the TIME buttons to set the
time.
Each press increases/decreases
the time by 1 minute (10 minutes
when pressed longer).
• Press CLOCK gently using a thin instrument.
En-3
SG79F572H01_en.indd 3
2012/12/19 9:13:10
SELECTING OPERATION MODES
I FEEL mode
The unit selects the operation mode according to the room temperature
when I FEEL is selected. When the room temperature is higher than 25°C,
COOL is selected (set temperature: 24°C). When the room temperature
is lower than 25°C, DRY is selected. However, when operation is stopped
and then started within 2 hours, the mode which has been selected previously is operated.
Note:
During COOL operation, the set temperature may not be changed when
the room temperature is more than 2°C higher than the set temperature.
In this case, please wait until the room temperature drops to within 2°C of
the set temperature.
COOL mode
Enjoy cool air at your desired temperature.
DRY mode
Dehumidify your room. The room may be cooled slightly.
Temperature cannot be set during DRY mode.
FAN mode
Circulate the air in your room.
1
2
When the remote controller cannot be used...
Emergency operation can be activated by pressing the emergency operation
switch (E.O.SW) on the indoor unit.
Press
to select operation mode. Each press
changes mode in the following order:
(I FEEL)
3
Emergency operation
to start the operation.
Press
(COOL)
(DRY)
Each time the E.O.SW is pressed, the operation changes in
the following order:
(FAN)
Operation indicator lamp
Emergency COOL
Press
or
to set the temperature.
Each press raises or lowers the temperature by 1°C.
Press
to stop the operation.
• The same setting is selected the next time by simply pressing
Stop
.
Set temperature : 24°C
Fan speed : Medium
Horizontal vane : Auto
Note:
The first 30 minutes of operation is test run. Temperature
control does not work, and fan speed is set to High.
Operation indicator lamp
The operation indicator lamp shows the operation state of the unit.
Indication
Operation state
Room temperature
About 2°C or more
The unit is operating to reach the set
away from set temtemperature
perature
The room temperature is approach- About 1 to 2°C from
ing the set temperature
set temperature
Lighted
Not lighted
Auto restart function
If a power failure occurs or the main power is turned off during operation, “Auto
restart function” automatically starts operation in the same mode as the one
set with the remote controller just before the shutoff of the main power. When
timer is set, timer setting is cancelled and the unit starts operation when power
is resumed.
If you do not want to use this function, please consult the service representative because the setting of the unit needs to be changed.
En-4
SG79F572H01_en.indd 4
2012/12/19 9:13:12
● OPERATING INSTRUCTIONS ●
FAN SPEED AND
AIRFLOW DIRECTION ADJUSTMENT
Press
to select fan speed. Each press changes
fan speed in the following order:
(AUTO)
(Low)
(Med.)
(High)
Press
to select vertical airflow direction. Each
press changes airflow direction in the following order:
(1)
(2)
(3)
(4)
Press
to start LONG operation.
Press
again to cancel LONG operation.
• Fan speed increases and the horizontal vane moves to the position
for LONG mode.
• Air reaches to longer distance.
(Super High)
• Two short beeps are heard from the indoor unit when set to AUTO.
(AUTO)
LONG OPERATION
(5)
(SWING)
• Two short beeps are heard from the indoor unit when set to AUTO.
Press
to select horizontal airflow direction. Each
press changes airflow direction in the following order:
(SWING)
Airflow direction
(AUTO)
• LONG operation is cancelled when the ON/OFF, VANE, or ECONO
COOL button is pressed.
POWERFUL COOL OPERATION
Press
during COOL mode page 4 to start
POWERFUL COOL operation.
Fan speed
: Exclusive speed for POWERFUL mode
Horizontal vane : Set position, or downward airflow position during
AUTO setting
• Temperature cannot be set during POWERFUL COOL operation.
Press
operation.
again to cancel POWERFUL COOL
• POWERFUL COOL operation also is cancelled automatically in 15
minutes, or when the ON/OFF, FAN, or ECONO COOL button is
pressed.
The vane is set to the most efficient airflow direction. :horizontal position.
(Manual)
For efficient air conditioning, select the upper position for COOL/DRY. If the
position (4) or (5) is selected during COOL/DRY, the vane automatically
moves to the horizontal position after 0.5 to 1 hour to prevent any condensation from dripping.
(Swing)
The vane moves up and down intermittently.
En-5
SG79F572H01_en.indd 5
2012/12/19 9:13:15
ECONO COOL OPERATION
Press
during COOL mode page 4 to start
ECONO COOL operation.
The unit performs swing operation vertically in various cycles according to the
temperature of airflow. Set temperature is set 2°C higher automatically.
Press
again to cancel ECONO COOL operation.
• ECONO COOL operation is cancelled when the VANE, LONG, or
POWERFUL COOL button is pressed.
What is “ECONO COOL”?
Swing airflow (change of airflow) makes you feel cooler than stationary airflow. So,
even though the set temperature is automatically set at 2°C higher, it is possible to
perform cooling operation with keeping comfort. As a result, energy can be saved.
TIMER OPERATION (ON/OFF TIMER)
1
Press
or
during operation to set the timer.
(ON timer) : The unit turns ON at the set
time.
(OFF timer) : The unit turns OFF at the set
time.
*
or
blinks.
* Make sure that the current time is set correctly. Page 3
2
Press
(Increase) and
time of timer.
(Decrease) to set the
Each press increases or decreases the set time by 10 minutes.
or
is blinking.
• Set the timer while
3
Press
or
again to cancel timer.
Note:
• ON and OFF timers can be used in combination. mark indicates the order
of timer operations.
• If power failure occurs while ON/OFF timer is set, see page 4 “Auto restart
function”.
En-6
SG79F572H01_en.indd 6
2012/12/19 9:13:18
● OPERATING INSTRUCTIONS ●
CLEANING
Instructions:
• Switch off the power supply or turn off the breaker before cleaning.
• Be careful not to touch the metal parts with your hands.
• Do not use benzine, thinner, polishing powder, or insecticide.
• Use only diluted mild detergents.
• Do not expose parts to direct sunlight, heat, or fire to dry.
• Do not use water hotter than 50°C.
Air cleaning filter
(Electrostatic anti-allergy enzyme filter,
option)
Air filter (Nano platinum filter)
• Clean every 2 weeks
• Remove dirt by a vacuum cleaner, or rinse with water.
• After washing with water, dry it well in shade.
What is “Nano platinum filter”?
Nano platinum is a ceramic particle that includes a platinum nanoparticle.
The particles are incorporated into the filter material, which results in providing semi-permanent antibacterial and deodorizing characteristics for the
filter. Nano platinum surpasses the catechin (a bioflavonoid that is found
in green tea) in performance. Nano platinum filter uses this compound not
only to improve air quality but also to eliminate bacteria and viruses. This air
filter has a semi-permanent lasting effect even after washing it with water.
Every 3 months:
• Remove dirt by a vacuum cleaner.
When dirt cannot be removed by vacuum cleaning:
• Soak the filter and its frame in lukewarm water before rinsing it.
• After washing, dry it well in shade.
Every year:
• Replace it with a new air cleaning filter for best performance.
• Parts Number MAC-2310FT-E
Important
• Clean the filters regularly for best performance and to
reduce power consumption.
• Dirty filters cause condensation in the air conditioner
which will contribute to the growth of fungi such as
mold. It is therefore recommended to clean air filters
every 2 weeks.
Front panel
1. Lift the front panel until a “click” is heard.
Hinge
Hole
2. Hold the hinges and pull to remove as shown in the left illustration.
• Wipe with a soft dry cloth or rinse it with water.
• Do not soak it in water for more than two hours.
• Dry it well in shade.
3. Install the front panel by following the removal procedure in reverse. Close the
front panel securely and press the positions indicated by the arrows.
En-7
SG79F572H01_en.indd 7
2012/12/19 9:13:19
WHEN YOU THINK THAT TROUBLE HAS OCCURRED
Even if these items are checked, when the unit does not recover from the
trouble, stop using the air conditioner and consult your dealer.
Symptom
Explanation & Check points
Indoor Unit
The unit cannot be operated.
• Is the breaker turned on?
• Is the power supply plug connected?
• Is the ON timer set? Page 6
The unit cannot be operated
for about 3 minutes when
restarted.
• This protects the unit according to instructions from the microprocessor. Please
wait.
The fan stops during the DRY
operation.
• In DRY operation, the unit operates using the
same refrigerant circuit as in COOL operation. DRY operation time has to be reduced
in order to lower humidity without much room
temperature decreasing. So the compressor sometimes stops, and at the same time
the indoor fan stops. This prevents water
condensed on the heat exchanger from
evaporating again.
Mist is discharged from the air • The cool air from the unit rapidly cools moisoutlet of the indoor unit.
ture in the air inside the room, and it turns
into mist.
The swing operation of the
HORIZONTAL VANE is
suspended for a while, then
restarted.
• This is for the swing operation of the HORIZONTAL VANE to be performed normally.
The air flow direction changes • When the unit is operated in COOL or DRY
mode, if the operation continues with air
during operation.
blowing down for 0.5 to 1 hour, the direction
The direction of the horizontal
of the air flow is automatically set to horizonvane cannot be adjusted with
tal position to prevent water from condensing
the remote controller.
and dripping.
The unit starts operation by
itself when the main power is
turned on, but isn’t received
sign from the remote controller.
The indoor unit discolors over
time.
• These models are equipped with an auto restart function. When the main power is turned
off without stopping the unit with the remote
controller and is turned on again, the unit
starts operation automatically in the same
mode as the one set with the remote controller just before the shutoff of the main power.
Refer to “Auto restart function” Page 4 .
• Although plastic turns yellow due to the influence of some factors such as ultraviolet light
and temperature, this has no effect on the
product functions.
Symptom
Explanation & Check points
Airflow
The air from the indoor unit
smells strange.
• Are the filters clean? Page 7
• Is the fan or heat exchanger of the indoor unit
clean? Page 7
• The unit may suck in an odor adhering to the
wall, carpet, furniture, cloth, etc. and blow it
out with the air.
Sound
Cracking sound is heard.
• This sound is generated by the expansion/
contraction of the front panel, etc. due to
change in temperature.
“Burbling” sound is heard.
• This sound is heard when the outside air is
absorbed from the drain hose by turning on
the range hood or the ventilation fan, making
water flowing in the drain hose to spout out.
This sound is also heard when the outside air
blows into the drain hose in case the outside
wind is strong.
Mechanical sound is heard
from the indoor unit.
• This is the switching sound in turning on/off
the fan or the compressor.
The sound of water flowing
is heard.
• This is the sound of refrigerant or condensed
water flowing in the unit.
In the following cases, stop using the air conditioner and consult your dealer.
• When water leaks or drips from the indoor unit.
• When the upper operation indicator lamp blinks.
• When the breaker trips frequently.
• The remote control signal is not received in a room where an electronic ON/OFF
type fluorescent lamp (inverter-type fluorescent lamp, etc.) is used.
• Operation of the air conditioner interferes with radio or TV reception. An amplifier may be required for the affected device.
• When an abnormal sound is heard.
Outdoor Unit
Water leaks from the outdoor
unit.
• During COOL and DRY operations, pipe or
pipe connecting sections are cooled and this
causes water to condense.
Remote controller
The display on the remote
controller does not appear or
it is dim. The indoor unit does
not respond to the remote
control signal.
• Are the batteries exhausted? Page 3
• Is the polarity (+, -) of the batteries correct?
Page 3
• Are any buttons on the remote controller of
other electric appliances being pressed?
Does not cool
The room cannot be cooled
sufficiently.
• Is the temperature setting appropriate?
Page 4
• Is the fan setting appropriate? Please
change fan speed to higher setting.
Page 5
• Are the filters clean? Page 7
• Is the fan or heat exchanger of the indoor
unit clean? Page 7
• Are there any obstacles blocking the air inlet
or outlet of the indoor or outdoor unit?
• Is a window or door open?
• When a ventilation fan or a gas cooker is
used in a room, the cooling load increases,
resulting in an insufficient cooling effect.
• When the outside temperature is high, the
cooling effect may not be sufficient.
En-8
SG79F572H01_en.indd 8
2012/12/19 9:13:20
● OPERATING INSTRUCTIONS ●
W
INSTALLATION PLACE AND
HEN THE AIR CONDITIONER IS NOT
GOING TO BE USED FOR A LONG TIME
1
ELECTRICAL WORK
Installation place
Set to the highest temperature in manual COOL mode,
and operate for 3 to 4 hours. Page 4
Avoid installing the air conditioner in the following places.
• Where there is much machine oil.
• Salty places such as the seaside.
• Where sulfide gas is generated such as a hot spring.
• Where oil is splashed or where the area is filled with oily smoke (such as cooking areas and factories, in which the properties of plastic could be changed
and damaged).
• Where there is high-frequency or wireless equipment.
• Where the air from the outdoor unit air outlet is blocked.
• Where the operation sound or air from the outdoor unit does not bother the
house next door.
• This dries the inside of the unit.
• Moisture in the air conditioner contributes to favorable conditions for
growth of fungi, such as mold.
2
3
4
Press
to stop the operation.
Turn off the breaker and/or disconnect the power supply plug.
The installation location of the outdoor unit should
be at least 3 m away from the antennas for TV sets,
radios, etc. In areas where the reception is weak,
provide greater space between the outdoor unit and
the antenna of the affected device if operation of the air
conditioner interferes with radio or TV reception.
Remove all batteries from the remote controller.
When using the air conditioner again:
1
2
3
4
Inverter-type
fluorescent lamp
To prevent the effects
of a fluorescent lamp,
keep as far apart as
possible.
wall, etc.
Clean the air filter. Page 7
Check that the air inlet and outlet of the indoor and
outdoor units are not blocked.
Keep a space to
prevent the picture distortion or
the noise.
1m
or more
Cordless
phone or
Portable
phone
Check that the earth is connected correctly.
1m
or more
Wellventilated dry
place
100 mm or
more
(50/60, 80)
200/500 mm
or more
TV
3 m or
more
Radio
Electrical work
Refer to the “PREPARATION BEFORE OPERATION”,
and follow the instructions. Page 3
• Provide an exclusive circuit for the power supply of the air conditioner.
• Be sure to observe the breaker capacity.
If you have any questions, consult your dealer.
SPECIFICATIONS
Model
Set name
MS-GF50VA
MS-GF60VA
Indoor
MS-GF50VA
MS-GF60VA
MS-GF80VA
Outdoor
MU-GF50VA
MU-GF60VA
MU-GF80VA
Cooling
Cooling
Function
Cooling
Power supply
MS-GF80VA
~ /N, 230 V, 50 Hz
Capacity
kW
4.85
6.4
7.8
Input
kW
1.48
2.17
2.78
Weight
Indoor
kg
Outdoor
kg
38
57
72
kg
1.20
1.30
1.85
Refrigerant filling capacity (R410A)
16
Indoor
IP code
IP 20
Outdoor
Permissible excessive
operating pressure
Noise level
IP 24
LP ps
MPa
1.64
HP ps
MPa
4.15
Indoor (Super High/
High/Med./Low)
dB(A)
45/42/38/34
48/45/41/37
50/47/43/39
Outdoor
dB(A)
52
54
55
Guaranteed operating range
Cooling
Indoor
Outdoor
Upper limit
35°C DB
24°C WB
46°C DB
—
Lower limit
21°C DB
15°C WB
21°C DB
—
DB: Dry Bulb
WB: Wet Bulb
Note:
1. Rating condition
Cooling — Indoor:
27°C DB, 19°C WB
Outdoor: 35°C DB
2. Noise measurement is carried out in accordance with JIS C9612 and ISO
5151(T1).
En-9
SG79F572H01_en.indd 9
2012/12/19 9:13:21
EC DECLARATION OF CONFORMITY
EG-KONFORMITÄTSERKLÄRUNG
DÉCLARATION DE CONFORMITÉ CE
EG-CONFORMITEITSVERKLARING
DECLARACIÓN DE CONFORMIDAD CE
DICHIARAZIONE DI CONFORMITÀ CE
ΔΗΛΩΣΗ ΠΙΣΤΟΤΗΤΑΣ ΕΚ
DECLARAÇÃO DE CONFORMIDADE CE
EU-OVERENSSTEMMELSESERKLÆRING
EG-DEKLARATION OM ÖVERENSSTÄMMELSE
EC UYGUNLUK BEYANI
ДЕКЛАРАЦИЯ СООТВЕТСТВИЯ НОРМАМ ЕС
CE-ERKLÆRING OM SAMSVAR
EY-VAATIMUSTENMUKAISUUSVAKUUTUS
MITSUBISHI ELECTRIC CONSUMER PRODUCTS (THAILAND) CO., LTD
AMATA NAKORN INDUSTRIAL ESTATE 700/406 MOO 7, TAMBON DON HUA ROH, AMPHUR MUANG, CHONBURI 20000, THAILAND
hereby declares under its sole responsibility that the air conditioners and heat pumps described below for use in residential, commercial and light-industrial environments:
erklärt hiermit auf seine alleinige Verantwortung, dass die Klimaanlagen und Wärmepumpen für das häusliche, kommerzielle und leicht-industrielle Umfeld wie unten beschrieben:
déclare par la présente et sous sa propre responsabilité que les climatiseurs et les pompes à chaleur décrits ci-dessous, destinés à un usage dans des environnements résidentiels,
commerciaux et d’industrie légère :
verklaart hierbij onder eigen verantwoordelijkheid dat de voor residentiële, commerciële en licht-industriële omgevevingen bestemde airconditioners en warmtepompen zoals onderstaand beschreven:
por la presente declara bajo su única responsabilidad que los acondicionadores de aire y bombas de calor descritas a continuación para su uso en entornos residenciales, comerciales y de industria ligera:
conferma con la presente, sotto la sua esclusiva responsabilità, che i condizionatori d’aria e le pompe di calore descritti di seguito e destinati all’utilizzo in ambienti residenziali, commerciali e semi-industriali:
με το παρόν πιστοποιεί με αποκλειστική της ευθύνη ότι οι τα κλιματιστικά και οι αντλίες θέρμανσης που περιγράφονται παρακάτω για χρήση σε οικιακό, επαγγελματικό και ελαφράς
βιομηχανίας περιβάλλοντα:
através da presente declara sob sua única responsabilidade que os aparelhos de ar condicionado e bombas de calor abaixo descritos para uso residencial, comercial e de indústria
ligeira:
erklærer hermed under eneansvar, at de herunder beskrevne airconditionanlæg og varmepumper til brug i privat boligbyggeri, erhvervsområder og inden for let industri:
intygar härmed att luftkonditioneringarna och värmepumparna som beskrivs nedan för användning i bostäder, kommersiella miljöer och lätta industriella miljöer:
ev, ticaret ve hafif sanayi ortamlarında kullanım amaçlı üretilen ve aşağıda açıklanan klima ve ısıtma pompalarıyla ilgili aşağıdaki hususları yalnızca kendi sorumluluğunda beyan
eder:
настоящим заявляет и берет на себя исключительную ответственность за то, что кондиционеры и тепловые насосы, описанные ниже и предназначенные для эксплуатации в жилых помещениях, торговых залах и на предприятиях легкой промышленности:
erklærer et fullstendig ansvar for undernevnte klimaanlegg og varmepumper ved bruk i boliger, samt kommersielle og lettindustrielle miljøer:
vakuuttaa täten yksinomaisella vastuullaan, että jäljempänä kuvatut asuinrakennuksiin, pienteollisuuskäyttöön ja kaupalliseen käyttöön tarkoitetut ilmastointilaitteet ja lämpöpumput:
MITSUBISHI ELECTRIC, MS-GF50VA/MU-GF50VA, MS-GF60VA/MU-GF60VA, MS-GF80VA/MU-GF80VA
Note: Its serial number is on the nameplate of the product.
Hinweis: Die Seriennummer befindet sich auf dem Kennschild des Produkts.
Remarque : Le numéro de série de l’appareil se trouve sur la plaque du produit.
Opmerking: het serienummer staat op het naamplaatje van het product.
Nota: El número de serie se encuentra en la placa que contiene el nombre del producto.
Nota: il numero di serie si trova sulla targhetta del prodotto.
Σημείωση: Ο σειριακός του αριθμός βρίσκεται στην πινακίδα ονόματος του προϊόντος.
Directives
Richtlinien
Directives
Richtlijnen
Directivas
Direttive
Οδηγίες
Nota: o número de série encontra-se na placa que contém o nome do produto.
Bemærk: Serienummeret står på produktets fabriksskilt.
Obs: Serienumret finns på produktens namnplåt.
Not: Seri numarası ürünün isim plakasında yer alır.
Примечание: серийный номер указан на паспортное табличке изделия.
Merk: Serienummeret befinner seg på navneplaten til produktet.
Huomautus: Sarjanumero on merkitty laitteen arvokilpeen.
Directivas
Direktiver
Direktiv
Direktifler
Директивы
Direktiver
Direktiivit
2006/95/EC: Low Voltage Directive
2006/42/EC: Machinery Directive
2004/108/EC: Electromagnetic Compatibility Directive
Our authorized representative in EU, who is authorized to compile the technical file, is
as follows.
Unser autorisierter Vertreter in der EU, der ermächtigt ist die technischen Daten zu
kompilieren, ist wie folgt.
Notre représentant agréée dans L’UE, qui est autorisé à compiler le fichier technique,
est le suivant.
Onze geautoriseerde vertegenwoordiger in de EU, die gemachtigd is het technische
bestand te compileren, is als volgt.
Nuestro representante autorizado en la UE, que está autorizado para compilar el archivo técnico, es el siguiente.
Il nostro rivenditore autorizzato nell’UE, responsabile della stesura della scheda tecnica, è il seguente.
Ο εξουσιοδοτημένος αντιπρόσωπός μας στην ΕΕ, ο οποίος είναι εξουσιοδοτημένος να
συντάξει τον τεχνικό φάκελο, είναι ο εξής.
O nosso representante autorizado na UE, que está autorizado para compilar o ficheiro
técnico, é o seguinte:
Vores autoriserede repræsentant i EU, som er autoriseret til udarbejdelse af den tekniske fil, er følgende.
Vår EG-representant som är auktoriserad att sammanställa den tekniska filen är följande.
Avrupa Birliği’nde bulunan ve teknik dosyayı düzenleme yetkisine sahip yetkili temsilcimiz aşağıda belirtilmiştir:
Наш авторизованный представитель в ЕС, уполномоченный на составление технического файла, указан ниже.
Vår autoriserte EU-representant, som har autorisasjon til å utarbeide denne tekniske
filen, er som følger.
Valtuutettu EU-edustaja, joka on valtuutettu laatimaan teknisen eritelmän, on mainittu
alla.
MITSUBISHI ELECTRIC EUROPE, B.V.
HARMAN HOUSE, 1 GEORGE STREET, UXBRIDGE, MIDDLESEX UB8 1QQ, U.K.
Yoji SAITO
Product Marketing Director
Issued:
THAILAND
17 December, 2012
Tomoyuki MIWA
Manager, Quality Assurance Department
HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
SG79F572H01
SG79F572H01_Cover.indd 2
2012/12/19 9:14:20