Bosch FPA-1200-MPC User guide

Panel Controller
MPC-xxxx-C | FPA-1200-MPC-C
en
User Guide
Panel Controller
Table of Contents | en
3
Table of contents
1
For your information
8
1.1
Depiction of steps
8
1.2
Calling up the start menu
8
1.3
Changing language display
9
1.4
Warranty and liability
9
1.5
Copyright
2
For your safety
10
2.1
Symbols and notes used
10
2.2
Operating the touch screen
10
2.3
Maintenance
11
2.4
Usage in accordance with regulations
11
2.5
Skills required by personnel
11
3
All functions at a glance
12
3.1
Calling up the start menu
12
3.2
Bypass/Isolate
12
3.2.1
Bypass
12
3.2.2
Isolate
12
3.3
Diagnostics
13
3.4
Maintenance
14
3.4.1
Walktest
14
3.4.2
Change language
15
3.4.3
Activate Outputs
15
9
3.4.4
Activate the transmission device
15
3.4.5
Detector removal
15
3.4.6
History Log
15
3.4.7
Change device on V.24 Interface
15
3.5
Configuration
16
3.6
Switching to day or night mode
16
3.7
Further functions
17
3.8
Search Function/Element
17
3.9
Reset
18
4
In overview
19
4.1
Operating elements
19
4.2
Display elements
20
4.3
Touch screen
22
4.4
Standby display
23
4.5
Display support information
24
5
Operating principle
25
5.1
Logging on and off
25
5.1.1
Logging in
25
5.1.2
Logging out
26
5.2
Access authorization
26
5.3
Calling up the start menu
26
5.4
Selecting the menu
26
5.5
Returning to the previous selection
26
5.6
Working with lists
27
5.6.1
Scrolling through lists
27
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
4
en | Table of Contents
Panel Controller
5.6.2
Various states of list fields
28
5.6.3
Selecting element/function
29
5.6.4
Assigning mode
29
5.7
Search Function/Element
29
5.7.1
Search by name
30
5.7.2
Searching by number
30
5.8
Entering numbers and text
30
5.8.1
Changing an entry
31
5.8.2
Deleting all numbers
32
5.9
Changing language display
32
5.9.1
Entering key combination
32
5.10
Switching between status bars
32
5.11
Standby
32
5.12
Logical and physical addressing
32
6
Networked panels
34
6.1
Icons on the display
34
6.2
Network addressing
34
6.3
Establishing a remote connection with a networked panel
35
6.4
Terminating a remote connection with a networked panel
35
6.5
Isolating and restricted connection
35
7
Networking via Ethernet
37
7.1
IP settings
37
7.2
Ethernet redundancy
38
7.3
Diagnostics
39
8
Remote keypad
40
8.1
Operation and display
40
9
Alarm
41
9.1
Types of alarm
41
9.2
Entry delays
41
9.3
Day and night mode
42
9.4
Alarm message to the panel
43
9.4.1
Optical and acoustic signals
43
9.4.2
Displaying the detector zones in alarm state
43
9.4.3
Sequence of the alarm messages
44
9.4.4
Information about logical zones in the alarm state
44
9.4.5
The newest message
45
9.4.6
Displaying the individual detectors in a logical zone
45
9.4.7
Information about individual detectors
45
9.4.8
Displaying additional information
46
10
Fire alarm
47
10.1
Optical and acoustic signals
47
10.2
Acknowledging a message
47
10.3
Switching off internal buzzer
47
10.4
Switching external signaling devices on and off
48
10.5
Resetting external signaling devices and transmission devices
48
10.6
Triggering fire verification
48
10.6.1
Alarm verification
48
10.6.2
Starting time to investigate
49
10.6.3
Triggering alarm manually
49
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Table of Contents | en
5
10.7
Resetting alarm message
50
10.8
Bypassing detectors
50
11
Fault message
52
11.1
Calling up fault indication
52
11.2
Trouble message on the panel
52
11.2.1
Acknowledging a message
52
11.2.2
Sequence of the trouble messages
53
11.2.3
Information about malfunctioning element groups
53
11.2.4
The newest message
53
11.2.5
Displaying individual elements of an element group
54
11.2.6
Information about individual elements
54
11.2.7
Displaying additional information
54
11.2.8
Signals
55
11.3
Resetting malfunction message
55
11.4
Isolating an element
55
12
Bypass
57
12.1
Menu overview
57
12.2
Bypassing and un-bypassing elements
57
12.3
Displaying and un-bypassing bypassed element groups
58
12.4
Displaying list of all bypassed elements
58
12.4.1
Using the menu
58
12.4.2
Via the status bar
59
12.5
Bypassing/Un-bypassing buzzer
59
13
Isolate
60
13.1
Menu overview
60
13.2
Isolating and de-isolating elements
60
13.3
Displaying list of all isolated elements
60
13.3.1
Using the menu
61
13.3.2
Via the status bar
61
14
Diagnostics
62
14.1
Menu overview
62
14.2
Element details
62
14.3
Modules
63
14.4
Hardware
63
14.4.1
Address cards
63
14.4.2
Display
63
14.4.3
Serial Interface
65
14.4.4
CAN-Bus
65
14.5
Panel Passport
65
14.6
LED Test on modules
65
14.7
Network services
65
14.7.1
Routing table
65
14.7.2
Consistency check
66
14.7.3
Ethernet ports
66
14.7.4
Send ping command
67
14.7.5
Ethernet redundancy
67
14.7.6
Condition Monitoring
68
14.8
Voice alarm systems
68
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
6
en | Table of Contents
Panel Controller
15
Maintenance
70
15.1
Menu overview
70
15.2
Changing language display
70
15.3
Activate Outputs
70
15.4
Activate Transmission Device
71
15.5
Detector removal
71
15.6
Change device on V.24 Interface
71
15.7
Bypassing/Un-bypassing buzzer
72
16
Maintenance – walktest
73
16.1
Walktest groups
73
16.1.1
Adding or deleting elements
73
16.2
Starting and ending walktest
75
16.2.1
Starting the walktest
75
16.2.2
Ending the walktest
75
16.3
Ending walktest for all elements
75
16.4
Displaying tested or untested elements
76
16.5
Assigning tested elements to a walktest group
76
17
Maintenance – history log
77
17.1
Selecting filters
77
17.2
Setting filters
77
17.3
Change Filter
78
17.4
Combining several filters
78
17.5
Status bar functions
78
17.6
Printing out data
79
18
Day and night mode
80
18.1
Switching between day and night mode
80
18.2
Showing details
81
18.3
Changing the time for resetting to night mode
81
19
Configuration
83
19.1
Menu overview
83
19.2
Input / Output Group Set Up
83
19.2.1
Adding or deleting elements
83
19.2.2
Change name
85
19.3
Group setting
85
19.3.1
Adding or removing
85
19.4
Detector sensitivity
85
19.5
Operator
86
19.5.1
Change password
86
19.5.2
Change universal password
86
19.5.3
Set Default Password
87
19.6
Rename elements
87
19.7
Network
87
19.8
Overview
87
20
Further functions
89
20.1
Menu overview
89
20.2
Change Date / Time
89
20.3
Master password
89
20.3.1
Enter the master password that is valid indefinitely
89
20.3.2
Enter the 24-hour master password
90
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Table of Contents | en
7
20.4
Remote Access
90
20.5
Change password
90
20.6
Performing a fire drill
91
20.7
Alarm Counters
91
21
Reset
93
21.1
Menu overview
93
21.2
Resetting elements
93
22
Search Function/Element
94
22.1
Menu overview
94
22.2
Searching for function and device description
94
22.3
Search element
94
Index
95
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
8
1
en | For your information
Panel Controller
For your information
This operation guide contains important information and notes on operating the FPA-5000 and
FPA-1200 fire panels.
Using the step-by-step directions, you can familiarize yourself with the individual functions:
–
In overview, page 19 provides an overview of the operating and display elements and the
touch screen.
–
In Operating principle, page 25, you will learn how to navigate through the individual
menus and which selection possibilities are available to you.
Each function is described in detail in an individual chapter.
Notice!
In standby mode, the standby screen is displayed. This contains different information
depending on the configuration.
If no longer operated, the panel controller switches to standby mode after 5 minutes and an
alarm event occurs after one hour. The touch screen backlighting switches off. To quit
standby mode, touch any part of the touch screen.
To call up the start menu or change the language display, see Operating principle, page 25.
You will find specific topics in the table of contents. If you are already practiced in the
handling of menus, you can use the overview of all menus in All functions at a glance, page
12.
1.1
Depiction of steps
The sequence of steps that you need to execute a function is depicted as follows:
1.
In the start menu, select Bypass Block
2.
Bypass
In more detailed form:
1.
1.2
Call up the start menu.
2.
Select Bypass Block.
3.
Select Bypass.
Calling up the start menu
4
Press the "home" key.
You can use this key to return from any submenu back to the start menu.
Notice!
The display changes from each menu element to the standby display if no entries are made
within one minute.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
1.3
For your information | en
9
Changing language display
The panel language can be changed quickly with a shortcut; see the following instruction To
change the panel language using the menu, see Changing language display, page 32.
1.
Select the "home" key.
2.
Then press 1 on the alphanumeric keypad immediately after this.
3.
Select OK to confirm the entry or Cancel to cancel the operation.
A list of the existing languages is displayed.
4.
Select the language you require.
The displays are displayed in the selected language.
Notice!
After a system reboot following a power cut or battery failure, the default language set in the
FSP‑5000‑RPS is displayed again.
1.4
Warranty and liability
Warranty and liability claims for personal and property damage are excluded if these were
caused by one or several of the following causes:
–
Use of the FPA-5000 and FPA-1200 fire panels contrary to the regulations
–
Improper set-up, installation, start-up, operation or maintenance
–
Disregarding of the user manual
–
Subsequent constructional changes
–
Faulty repairs
–
Catastrophes, influence of foreign bodies, and force majeure.
Without the permission of Bosch, no changes or additions to or rebuilding of the panel
including the panel controller may be undertaken.
Rebuilding requires written permission. In case of non-approved constructional changes, any
warranty claims against Bosch are voided.
1.5
Copyright
Bosch retains the complete copyright to the whole documentation. Without the express
written permission of Bosch, no part of these documents may be duplicated or transmitted in
any form.
Bosch reserves the right to make changes to this manual without prior notice.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
10
en | For your safety
2
Panel Controller
For your safety
Before using the device, familiarize yourself with these instructions. If you do not read and
understand these explanations, you will not be able to operate the device faultlessly.
The operating instructions do not do away with the need for training by authorized personnel.
Notice!
The panel controller may only be operated by trained personnel. See skills required by
personnel.
This operation guide does not contain any general or special knowledge about safety issues.
Information on such issues is only given to the extent that it is needed for operation of the
device.
Ensure that you are familiar with all safety-related processes and regulations in your area. This
also includes how to behave in the event of an alarm and the initial steps to take if a fire
breaks out.
The operation guide should always be available on site. It is a statutory part of the system and
must be given to the new owner if the system is ever sold.
Notice!
The personal access code (consisting of user ID and password) must not be made known to
third parties.
2.1
Symbols and notes used
The various chapters only contain whatever safety information and notes are required for
operation of the system. Warning notes and operator guidance notes are displayed in the
appropriate parts of the panel controller display for your benefit.
The following search symbols are used:
Caution!
!
Text fields marked with this symbol contain warnings by which you must abide without fail —
for your own safety as well as that of the people around you
Notice!
Text fields marked with this symbol contain useful information to help you operate the
FPA-5000 and FPA‑1200 fire panels.
2.2
Operating the touch screen
Do not use any pointed or sharp objects when operating the touch-sensitive display. This
could damage the surface. Touch the touch screen with your finger (nail) or the stick attached
to the left-hand side of the panel controller.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
2.3
For your safety | en
11
Maintenance
Clean the touch screen and membrane keypad with a soft cloth only. If necessary, dampen the
cloth lightly with standard monitor cleaning agents. Do not use any aggressive cleaning agents
and ensure that no liquid enters the inside of the device.
2.4
Usage in accordance with regulations
The panel controller is designed for operating the FPA-5000 and FPA‑1200 fire panels. It can
perform the following tasks:
2.5
–
Displaying and processing various message types such as alarm and trouble messages
–
Bypassing, isolating and resetting elements
–
Performing a walktest
–
Display diagnostic information about every LSN element
–
Configuration of detectors (short texts and detector sensitivity)
–
Performing a drill
–
Saving, displaying and printing out events
–
Switching the system to day or night mode.
Skills required by personnel
Display of event messages on the panel controller must only be processed by trained
personnel.
The system walk test and detector configuration must only be performed by trained,
authorized personnel.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
12
en | All functions at a glance
Panel Controller
3
All functions at a glance
3.1
Calling up the start menu
Press the "home" key to return to the start menu from any submenu.
Notice!
The display changes from each menu element to the standby display if no entries are made
within one minute; see also Standby display, page 23.
3.2
Bypass/Isolate
3.2.1
Bypass
Bypass
-> Bypass
Block
Block
-> Show bypassed
Select by
devices
number
NAC
Transmission
Bypass buzzer
Printer
HVAC
Doorholder
Extinguishing
Annunciator
device
Detector
Logical zone
system
Bypass group
More...
-> Control
Interface
element
module
Show bypassed devices
–
Display of a list of all bypassed elements:
–
Un-bypassing the bypassed elements.
Select by number
–
Display of a list of all bypassed elements:
3.2.2
Bypass
–
Search for an element in a list by entering the number.
–
Un-bypassing or bypassing an element.
Isolate
-> Bypass
Show blocked devices
Block
Select by
Block Group
Printer
Strobe
HVAC
Doorholder
Detector
Extinguishing
Annunciator
number
Block
-> Sounder
Transmission device
system
Logical zone
More...
-> Control
Interface
element
module
Show blocked devices
–
Display a list of all isolated elements
–
De-isolate isolated elements
Select by number
–
Display a list of all elements that can be isolated
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
3.3
All functions at a glance | en
–
Search for an element in a list by entering the number
–
Isolate or de-isolate an element
13
Diagnostics
Diagnostics
-> Element details
Modules
Hardware
Panel passport
LED test on modules
History log
Network
VAS
Element details
–
All info for one element: Display all diagnostic information about an element on a loop of
an LSN module.
–
Info for element group: Select and display specific pieces of diagnostic information
about several elements in the selected LSN module.
–
Info for all elements on the module: Select and display specific pieces of diagnostic
information about all LSN elements of the selected LSN module.
Modules
–
Module passport: Display diagnostic information for each individual module: production
data, software version, CAN ID, compatibility.
–
Module Compatibility: Display the software version of the selected module in
comparison with the control panel software version.
–
Module status: Display hardware diagnostic data for the selected module.
Only for LSN modules:
–
Module status and counters
–
Reset counters: Reset the counters that record the frequency with which various events
occur.
Hardware
–
Address cards: Additional display for each card slot of the serial number and number of
addresses per card.
–
Display
–
LED test: Test all LED displays on the panel controller. These remain lit for the
duration of approx. five seconds.
–
Key test: Test the operativeness of the membrane keypad.
–
Display test: Test the operativeness of the display.
–
Display touch test: Test the operativeness of the touch-sensitive surface.
–
Adjust touch screen: Adjust the location precision when touching the touchscreen.
–
Serial interface: Display statistical data for the transmission.
–
CAN bus: Display status of CAN interfaces.
Panel passport
Display diagnostic information such as manufacturing data or software version of the panel
controller.
LED test on modules
Test LED displays of individual modules and simultaneously test all LED displays.
History log
See Maintenance – History log
Network
–
Routing table
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
14
en | All functions at a glance
Panel Controller
Information concerning the accessibility of all interfaces and nodes within the system
network.
–
Ethernet ports
Information concerning various parameters and the status of the two Ethernet interfaces
available at the panel controller.
–
Send ping command
Sending of a ping command to a specific IP address to check the availability of other
nodes in the network.
–
Consistency check
The check performed determines whether the Ethernet configuration from FSP-5000-RPS
corresponds to the configuration entered at the panel controller. In the event of
discrepancies, a fault message is displayed.
–
Ethernet redundancy
Information concerning the type of redundancy configuration (RSTP or dual-homing). In
the case of redundancy via RSTP, the RSTP parameters of the RSTP panel (local bridge)
and those of the root bridge are displayed.
VAS
Information on all connected electro-acoustic systems that are used for voice evacuation
systems.
3.4
Maintenance
Maintenance
-> Walktest
Change language
Activate outputs
Activate transmission device
Remove detector
History log
Change device at V.24
Bypass buzzer
interface
3.4.1
Walktest
Start / End walktest
Elements for the walktest are selected in this submenu. The following possibilities are offered
for selection:
–
Select by number:
Display of a list of all elements:
Search for an element in a list by entering the number.
–
Walktest group
–
Loop
–
Logical zone
–
Elements
–
Transmission device
–
Control element
–
More...
–
DACT
–
Key deposit
–
Battery
–
Mains power
When the walktest is complete, the following selection options are available:
–
Adding the elements to be tested to a different walk test group (Assign tested elements
to walktest group).
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
All functions at a glance | en
–
Continuing the walk test (No).
–
Displaying tested or non-tested elements (Not tested, Tested).
15
Create / Change walktest group
–
Deleting or adding individual elements to specified walktest groups.
–
3.4.2
Delete all elements in a walktest group.
Change language
Change the language of the displays (Change language).
3.4.3
Activate Outputs
Activate outputs:
–
Select by number:
Display of a list of all controllable elements.
Search for an element in a list by entering the number.
–
Sounder
–
Strobe
–
HVAC
–
More...
Start and terminate activation of the selected elements.
3.4.4
Activate the transmission device
Activate a selected transmission device (Activate transmission device).
3.4.5
Detector removal
Bypass all sounders and transmission devices for 15 minutes while a detector is being
removed (Remove detector).
3.4.6
History Log
–
Filtering and displaying specific data
–
Combining various filters
–
Print out all filtered data or a specific part of the data
The following filters are available:
Filter
Data, filtered by...
Without filter
All data
Show all Delete filter
Display all data with specification of event number, date,
time, element number and message type. Existing filters are
deleted.
3.4.7
Period
Starting date, end date and time
Event types
Message types, such as Fault
Device types
Device types, such as Detectors
Address range
Address range within a system
User commands
Selected function fields, such as Acknowledge or Reset.
Walktest
Elements switched to walktest mode
Change device on V.24 Interface
Assigning a different device to the V.24 interface (Change device at V.24 interface).
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
16
3.5
en | All functions at a glance
Panel Controller
Configuration
Configuration
-> Set input / output
Set groups
groups
Detector sensitivity
Operator
Rename elements
Overview
Network
Set input / output groups
–
Input group or Output group
–
Displaying the assigned elements.
–
Add or delete elements.
–
Rename group names.
Set groups
–
Bypass group, isolate group or walktest group
–
Displaying the assigned elements.
–
Add or delete elements.
–
Rename walktest, bypass and isolate groups.
Detector sensitivity
Change the sensitivity of individual detectors or zones. Two selection options are available: a
default sensitivity and an alternative sensitivity assigned in the FSP-5000-RPS programming
software.
Operator
If the same password is used per access level, the following options are offered:
–
Change universal password
The same password can be configured for each access level in the FSP-5000-RPS
programming software. The password for access levels two to four can be changed.
If every user has a different password, the following options are offered:
–
Change operator data
Change a user's password.
–
Set default password
Reset an operator's password to his/her previous password.
Rename elements
Change the description of the elements.
Overview
Information on valid system configuration.
Network
Change and activate network settings (IP settings, Ethernet redundancy). Changes take effect
after restarting the panel.
Notice!
Changes may only be made by trained specialist personnel. Competent knowledge of
networking and protocols is essential!
3.6
Switching to day or night mode
–
Switch to day or night mode
–
In day mode: Set the reset time to night mode for the current day.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
3.7
All functions at a glance | en
17
Further functions
Further functions
-> Change date / time
Master password
Remote access
Change password
Drill
Alarm counters
Change date / time
Change the time and date
Master password
Depending on how the panel is configured, one of these two options will be offered:
–
Entering a master password that is valid indefinitely.
This password cannot be changed and is available from the relevant Bosch branch on
request
–
Entering a master password that is valid for a specified period of time. This password is
only valid for 24 hours and must first be requested; see Master password, page 89.
After the password has been entered, various options are offered depending on the
configuration; see Operator, page 86.
Drill
Start and terminate a fire drill During the drill, fire alarms, trouble messages and home
automation alarms are displayed.
Remote access
Create a remote access connection.
Change password
Depending on how the panel is configured, the option of changing the password for every user
is offered.
Alarm counters
–
Display the number of internal and external alarm messages and the number of service
alarms that were reported during the lifetime of the panel.
–
3.8
Reset the alarm counter for each alarm type
Search Function/Element
Search function /
->
Search function
element
Go to element
Search function
–
Display a list of all functions and device descriptions in alphabetical order.
–
Select a function or device description from the list.
Go to element
Display of a list of all elements that are connected to the system and select an element from
this list in order to display more detailed information.
–
by logical address: Search for an element in a list by entering the logical address
allocation.
–
by physical address: Search for an element in a list by entering the physical address
allocation.
–
By description: Search for an element in a list by entering the description.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
18
3.9
en | All functions at a glance
Panel Controller
Reset
Reset
-> Event type
Scope
Logical zone
Detector
This panel
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
4
In overview | en
19
In overview
This chapter contains information about the following elements of the panel controller:
–
Operating elements, page 19
–
Display elements, page 20
–
Touch screen, page 22
–
Standby display, page 23
–
Display support information, page 24
1
Alarm
Test
Transmission Device
activated
Bypassed
Bypass
Isolate
Diagnostics
Maintenance
Configuration
Switch to day mode
Further functions
Search Function/
Element
Reset
Transmission Device
bypassed
4
2
Signals bypassed
Power
Fault
Fault System
Fault Transmission Device
1
0
Fire
Fault Signals
0
Control
0
Fault
3
4.1
0
Bypass
Status
1
1
Function keys
3
Key switch
2
Alphanumeric keypad
4
LED display
Operating elements
The operating elements include points 1 - 3.
Function keys
To select a function, press the appropriate membrane key.
The following functions can be executed with the function keys:
Display a list of the networked panels and establish a remote
connection with a networked panel (only valid for FPA-5000) or a
remote keypad.
Display the address for technical support, if saved.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
20
en | In overview
Panel Controller
"Home" key. Call up the start menu.
Return to the previous selection.
"Key" key. Log in and out: Enter user ID and password.
Temporarily switch off the internal buzzer.
"Left arrow" key. Move the cursor one place to the left on the search
screen.
"Right arrow" key. Move the cursor one place to the right on the search
screen.
"Double arrow" key. Switch between status bars if two or more are
available. Call up the status bar to scroll rapidly through lists.
"Enter" key. Confirm an alphanumeric entry. Confirm an entry that is
not confirmed by selecting the OK field on the touch screen.
Alphanumeric keypad
Entry of letters, special characters, and numbers.
Key switch
The key switch has two programmable key positions. Depending on the configuration, it is
possible to switch between day and night operation, for example.
Notice!
Only give the key to people who have been trained to operate the panel controller and who
have knowledge in the area of fire protection. Otherwise, operation may be incorrect and
people may be injured. To prevent possible misuse, remove the key after operation and store
it in a secure location.
4.2
Display elements
LED display
Display
Color
Light signal
Steady
Alarm
Red
Meaning
Flashes
x
Panel is in alarm state Also
continuously on in event of Fire PAS
Walktest
Yello
x
System is being tested
x
Transmission device is activated
w
Transmission
Red
Device activated
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
In overview | en
Display
Color
Light signal
Steady
Bypassed
Yello
Yello
disabled
w
Signals disabled
Yello
Meaning
Flashes
x
Elements are bypassed and/or
w
Trans. Dev.
21
isolated
x
Transmission device is not activated
x
Signaling devices are not activated
w
Operation
Green x
Green
Panel is operational
x
Panel controller is booting and is not
yet operational
Green
Fault
Yello
x
Power supply fault
x
Fault message present
x
Main processor is malfunctioning
x
Transmission device is malfunctioning
w
Fault System
Yello
w
Fault
Yello
Transmission
w
Device
Fault Signals
Yello
x
w
Bosch Sicherheitssysteme GmbH
External signaling device
malfunctioning
User Guide
2013.07 | 3.0 | F.01U.258.929
22
4.3
en | In overview
Panel Controller
Touch screen
1
2
3
1
Info bar
2
Menu field
3
Status bar
Info bar
As long as an operator is logged in, this symbol will be displayed
on the right-hand side of the info bar.
There is a remote connection with a networked panel or a remote
keypad.
The networked panel is operated from another panel or from a
remote keypad and is blocked for operation.
There is a remote connection between panel A and a networked
panel B or a remote keypad, and panel A is operated
simultaneously from another panel C.
There is a restricted connection to the networked panel or a
remote keypad.
This icon is only displayed on the remote keypad if no connection
has yet been established.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
In overview | en
Panel 4 - 1 I Level 4
The network address and the access authorization of the
logged in
operator who has logged in (4) are displayed.
23
This symbol is displayed if a ground fault occurs in the system.
The names of the selected menus are also listed. Having the
menu path displayed will assist your orientation.
For reasons of space it is not always possible to display the
complete path. The selected menu and the menu you are
currently in are always displayed first.
Example:
The following path is displayed in the Sounder submenu of the
Block main menu:
* Bypass Block\Block\Sounder
Menu field
To select a main menu, touch the corresponding menu field on the touch screen. I All functions
at a glance, page 12, there is an overview of all main menus with their respective submenus.
Status bar
0
0
8
0
Fire
Control
Trouble
Bypass
Status
This status bar is available on each menu. In addition, other status bars are offered in some
menus; see also Switching between status bars, page 32:
The leading number specifies the number of elements in the respective state:
Fire
Number of groups that have triggered a fire alarm
Control
Elements that are activated
Trouble
Elements that have reported a fault
Bypass
Bypassed or isolated elements
In addition it is possible to display an overview of the type and nature of all message types
received by the panel:
Status
Display of a list of the various message and status types and the
number of elements in the respective state
To display the individual elements, touch the relevant field with your finger.
The Control and Trouble status fields are identified by the letters "B" and/or "C":
–
"B" means that controllers for type B fire safety equipment (G-B) are affected (e.g.
control elements without acknowledgement).
–
"C" means that controllers for type C fire safety equipment (G-C) are affected (e.g.
extinguishing systems).
4.4
Standby display
If the panel is in standby mode, the standby display is shown.
Notice!
The display changes from each menu element to the standby display if no entries are made
within ten minutes. If a gray display is shown, gently touch the touch screen to show the
standby display
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
24
en | In overview
Panel Controller
On the standby display, the following information is displayed:
–
Date
–
Time
Night mode
or
Day mode
Depending on the configuration, additional information may be displayed.
In a networked fire detection system, further icons can be displayed in the standby display
depending on the network setting; see Networked panels, page 34.
4.5
Display support information
To display the address of the company providing the support, please press:
Notice!
Information concerning support is only displayed if the information has already been entered
in FSP‑5000‑RPS.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
5
Operating principle | en
25
Operating principle
In addition to a brief menu overview, this chapter contains information about the following
points:
5.1
–
Logging on and off, page 25
–
Access authorization, page 26
–
Calling up the start menu, page 26
–
Selecting the menu, page 26
–
Returning to the previous selection, page 26
–
Working with lists, page 27
–
Search Function/Element, page 29
–
Entering numbers and text, page 30
–
Changing language display, page 32
–
Switching between status bars, page 32
–
Standby, page 32
–
Logical and physical addressing, page 32
Logging on and off
To gain access to access levels 2 to 4, it is necessary to log in. The prerequisite is that you
have access authorization.
Notice!
To log in, you need a user ID and password. Depending on your access authorization, you can
use only particular functions.
In the following cases, you will be asked to enter a password:
You are not logged on and want to select a function for which a password is required.
You are already logged in but a higher access authorization is required for the function you
have selected.
5.1.1
Logging in
To log in to the panel controller:
1.
Press the "key" key.
The login window is displayed:
2.
Enter your user ID in the first field.
Refer to Entering numbers and text, page 30 for information on how to enter numbers.
3.
Enter your password in the second field.
On the display, each digit of the password is indicated with an asterisk so that nobody
else can see the password.
Notice!
If you do not have your own password, enter the following numbers: 000000.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
26
en | Operating principle
4
Panel Controller
Select OK to confirm the entries or Cancel to cancel the operation.
Refer to Change password, page 90 for information on how to set up your own
password.
The standby display is shown.
As long as an operator is logged in, the key icon will be displayed on the info bar.
In addition, the user ID of the user who has logged on is displayed on the start page on the
info bar.
Notice!
In the FSP-5000-RPS programming software, a time span can be specified after which an
operator who is logged in to the panel controller is logged out.
5.1.2
Logging out
1.
To log out of the panel controller, press the "key" key:
An input window with the request Log off? is displayed:
2.
5.2
Select Yes to confirm the request or No to cancel the operation.
Access authorization
Notice!
Depending on your access authorization, you can only use certain functions of the panel
controller.
If you select a function for which a particular access authorization is required and no user with
the appropriate authorization is logged on, you will be asked to enter your user ID and
password.
Access authorizations are assigned for access levels two to four. Only a few functions can be
used on access level one, while all functions can be used on access level four.
To check the access authorization of the person who is logged in, press the "key" key after
logging in:
The relevant access authorization is displayed.
5.3
Calling up the start menu
Press the "home" key to return to the start menu from any submenu.
Notice!
The display changes from each menu element to the standby display if no entries are made
within one minute; see also Standby display, page 23.
5.4
Selecting the menu
In order to select a menu in the start menu, touch the field you require with your finger:
The submenus are displayed.
To select a submenu, gently touch the required field.
5.5
Returning to the previous selection
To return to the previous selection, press the "Back" key:
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
5.6
Operating principle | en
27
Working with lists
2
3
4
5
1
4
1
List
4
Arrows
2
List field
5
Function fields
3
Search mask
In many menus, elements are displayed in lists. The elements are sorted either by description
or address. Up to three different sorting criteria can be offered:
–
By description: sorted by description in alphabetical order; address allocation also given.
–
By number: sorted in ascending order by number (logical or physical address);
description also given.
–
By number (no description shown): by number (logical or physical address) in ascending
order; the numbers are displayed in number blocks and the description is not given. This
list is only offered when detectors and logical zones are being selected.
Example:
To display a list of all existing detectors sorted by description in the Bypass submenu, select
the following in the start menu:
1.
Bypass Block
2.
Bypass
3.
Detector
Three sorting criteria are offered for selection:
4
–
By description
–
By number
–
By number (no description shown)
Select By description.
A list of all detectors is displayed, sorted in alphabetical order.
5.6.1
Scrolling through lists
On the display, only a limited number of list fields can be displayed.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
28
en | Operating principle
Panel Controller
Select the "up arrow" key to scroll back through a long list:
Select the "down arrow" key to scroll forward through the list:
An arrow is only displayed if scrolling is possible.
Rapid scrolling:
To scroll quickly through a list, press the "double arrow" key on the membrane keypad or on
the status bar of the display.
A scrollbar appears on the status bar:
Gently touch the horizontal line to jump to a particular place.
To jump to the beginning of a list, touch:
To jump to the end of a list, touch:
5.6.2
Various states of list fields
Various states can be assigned to an element or an element group, depicted by a list field. The
following table provides information about the possible states:
List field
State of list
Meaning
field
TEXT
TEXT
TEXT
normal
Element in normal state
marked
Selected element
Mode assigned
The element was assigned the bypassed mode;
seeAssigning mode, page 29.
TEXT
Mode assigned
The selected element has already been assigned
and marked
a particular mode. It is selected in order to
reset it to the original mode; a bypassed
element is unbypassed, for example.
TEXT
2013.07 | 3.0 | F.01U.258.929
R
In reset mode
The resetting of the element is not yet
complete.
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Operating principle | en
29
"Bypass" menu
In the Bypass menu, list fields can display additional information; see the following table:
List field
In the Bypass menu
The bypassed element is in alarm mode. If it is un-bypassed, it
TEXT
triggers a fire alarm.
To display more information, press the right-hand field.
TEXT
Details
Display a bypass group that consists of several elements.
In order to display a list of all elements of the bypass group,
press the right-hand field.
5.6.3
Selecting element/function
To select elements/functions from a list, touch one or more list fields on the touch screen with
your finger.
In order to scroll forward or backward, select the up arrow (back) or the down arrow
(forward):
To scroll quickly using the scrollbar, select the "double arrow" key on the membrane keypad.
The activated list field is marked.
To search for and display a particular element; see Search Function/Element, page 29.
5.6.4
Assigning mode
A mode like Bypassed, Walktest etc. can be assigned to selected elements.
To assign a mode to selected elements, select the corresponding function field.
In the following example, a detector is assigned bypassed mode in the Bypass Block menu:
1.
Select the list fields you require from the list.
The list fields are marked.
2.
Select the Bypass function field.
The detectors are bypassed. The list fields are highlighted in a dark color.
The sand glass icon indicates an entry that is still being processed by the system.
Notice!
In the Bypass submenu, the function fields have an additional selection option; see Displaying
and un-bypassing bypassed element groups, page 58.
5.7
Search Function/Element
In lists, a particular element can be searched for and displayed using the search screen. The
following search criteria are offered:
–
By description: The element is searched for in the list by its description.
–
By number: The element is searched for in the list by its number. In some menus, the By
number (no description shown) search function is offered.
In the Search function / element main menu, it is possible to search for all elements
connected to the system and all functions offered in the panel controller, as well as device
descriptions, regardless of which menu they appear in; see Search Function/Element, page
94.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
30
en | Operating principle
5.7.1
Panel Controller
Search by name
To search in the By description list for a particular element, enter the name of the element in
the search screen.
Entering numbers and text, page 30 explains how to enter text.
Enter the initial letter and, if necessary, other letters.
The name is automatically completed once it has been uniquely recognized. The list field of
the element you are searching for is displayed at the beginning of the list.
Notice!
The more accurately the description of an element in the FSP-5000-RPS programming
software is entered, the more successful the search by name will be.
5.7.2
Searching by number
To search in the By number and By number (no description shown) list for a particular
element:
1.
Enter the first digit, for example 1.
2.
Press the "Enter" key to confirm the entry.
If the entry of another number is possible, a second search window is displayed.
Notice!
If you are not offered another field, there is no element with the addressing you have
searched for.
1.
Enter the next digit and confirm your entry with the "Enter" key.
2.
If necessary, enter further digits until the number is shown in full. You must confirm each
entry with the "Enter" key.
The list field of the element you are searching for is then displayed at the beginning of the list.
5.8
Entering numbers and text
Key
Character
.,-_0
1
ABCabc2
DEFdef3
GHIghi4
JKLjkl5
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Operating principle | en
Key
31
Character
MNOmno6
PQRSpqrs7
TUVtuv8
WXYZwxyz9
*
#
You can enter letters and numbers with each of the keys depicted.
Press the corresponding key on the membrane keypad until the required letter or number is
displayed.
Notice!
Only numbers can be entered in the search screen for the By number and By number (no
description shown) lists. In the search screen for the By description list, both letters and
numbers can be entered.
Example: Entering the letter K and the number 4 in the search screen of a list
1. Press the key:
A sequence of letters and numbers is displayed on the info bar.
2.
Keep pressing the key until the required letter, in this case K, is marked on the info bar. K
is displayed on the search window.
3.
Press the key:
and hold until the 4 on the info bar is marked.
The number 4 is displayed on the search window.
Quick entry:
In order to enter text quickly, press the "Enter" key after entering each letter.
This takes the cursor to the next free character and you can continue with entering the next
letter.
5.8.1
Changing an entry
1.
In order to change a number, press the "left arrow" or "right arrow" keys until the cursor
marks the number in the search screen that is to be replaced.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
32
en | Operating principle
2.
Panel Controller
To overwrite the marked number, press the key with the required number until the
number you require is displayed in the search screen.
5.8.2
Deleting all numbers
1.
In order to delete all numbers in the search screen, press the "left arrow" key until the
cursor marks the first number.
2.
Enter a new number using the number pad.
All numbers up to the digit entered are deleted.
3.
5.9
If you wish to, continue entering the numbers.
Changing language display
There are two ways to select another language display:
5.9.1
–
By entering a shortcut
–
Via a menu selection; see Changing language display, page 70.
Entering key combination
1.
Select the "home" key immediately followed by the 1 on the alphanumeric keypad. A
query window will appear.
2.
Select OK to confirm the entry or Cancel to cancel the operation.
A list of the existing languages is displayed.
3.
Select the language you require.
The displays will now be shown in the selected language.
Notice!
After the system starts up following a power cut or battery failure, the default language
defined in the FSP-5000-RPS programming software is set again.
5.10
Switching between status bars
The status bar offers further functions, display and selection options.
If the "double arrow" symbol is displayed in the status bar, it is possible to switch to the
status bar of the start menu. To do this, press the "double arrow" key on the membrane
keypad.
5.11
Standby
If no longer operated, the panel controller switches to standby mode after 5 minutes. The
touch screen backlighting switches off. To quit standby mode, touch any part of the touch
screen.
5.12
Logical and physical addressing
When addressing elements, there is a distinction between logical and physical addressing:
Physical
Elements
Modules
Loop
Element
Numbers
5
1
4
Logical
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Operating principle | en
Elements
Zone
Element
Numbers
3
4
33
[MISSINGDISPLAYTEXT: Examples: ]
Element with physical addressing: 5.1 - 4
Element with logical addressing: 3 - 4
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
34
6
en | Networked panels
Panel Controller
Networked panels
Panels can be networked with one another via a CAN bus or an Ethernet connection. This
chapter describes the similarities between the two physical networking principles. Detailed
notes on networking via Ethernet can be found in Networking via Ethernet, page 37. Details
on planning and commissioning are provided in the network manual. Fire detection systems
can only be networked with the FPA‑5000.
–
Icons on the display, page 34
–
Network addressing, page 34
–
Establishing a remote connection with a networked panel, page 35
–
Terminating a remote connection with a networked panel, page 35
–
Isolating and restricted connection, page 35: A restricted connection can be established
with a panel that is already operated by another panel (isolating connection).
–
Networking via Ethernet, page 37
The following functions cannot be carried out on a panel that is operated by another panel:
–
Bypass
–
Isolate
–
Switch to Walktest
–
Change configuration
You can reset elements and read out the history log.
6.1
Icons on the display
The following icons are displayed in the standby display/info bar/list field of a networked
panel, depending on the type of connection. Further explanations of the icons can be found in
Establishing a remote connection with a networked panel, page 35.
There is a remote connection between panel A or a remote keypad and
a networked panel B .
The networked panel B is operated from panel A or from a remote
keypad and is isolated for operation.
The networked panel B, with which panel A or a remote keypad has
already established a remote connection, in turn establishes a remote
connection with a networked panel C.
There is a restricted remote connection with a networked panel.
6.2
Network addressing
In the case of a networked panel, the network address is also displayed. The network address
consists of a node ID and group ID, which are assigned using the FSP-5000-RPS programming
software.
If, for example, a fault in a detector with network address 1 - 4 is displayed, this means:
–
Group ID = 1
–
Node ID = 4
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
6.3
Networked panels | en
35
Establishing a remote connection with a networked panel
4
In order to establish a remote connection with a networked panel B from a panel A, select
the "Network" key on panel A.
A list of the networked panels is displayed.
Refer to Working with lists, page 27 for information on how to navigate through a list.
Notice!
The fields in the list are shaded gray until the network is established.
1.
2.
Mark the list field you require.
Select OK and confirm the subsequent query with OK.
A remote connection is established with the panel B you have selected, and the following
icon is displayed in the info bar of panel A:
There is a remote connection between panel A and a networked panel B.
The networked panel B is operated from panel A and is blocked for operation. The
following icon is displayed in the info bar of panel B:
If, in this example, a panel B also establishes a remote connection, in this case with a
panel C, the following icon is displayed:
The networked panel B, with which panel A has already established a remote connection,
in turn establishes a remote connection with a networked panel C.
6.4
Terminating a remote connection with a networked panel
1.
In order to terminate a remote connection with another panel, select the "Network" key.
2.
Confirm the query after terminating the remote connection.
The remote connection is terminated.
6.5
Isolating and restricted connection
All functions can be operated via an isolating connection, with the exception of the following
functions:
–
LED, foil, display and display touch test
–
Adjust touch screen
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
36
en | Networked panels
Panel Controller
This icon is displayed on those networked panels, in this example panel B, with which another
panel, in this case A, has established an isolated connection.
A panel B, with which a panel A has established an isolating connection, cannot be operated
from another panel C.
However, a panel C can establish a restricted connection with a panel B that is already being
operated from a panel A.
If the connection is restricted, a panel can only be operated in read-only mode. All dialogs can
be accessed in read-only mode and the history log can be read out.
This icon is displayed if there is a restricted connection with a networked panel.
1.
In order to convert a restricted connection into an isolating connection, select the
"Network" key.
2.
Respond to the query concerning the termination of the connection with "No".
3.
Select the isolated panels you require from the list.
4.
Select OK and confirm the subsequent query with OK.
The isolation of the panel is lifted and a restricted connection is established.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
7
Networking via Ethernet | en
37
Networking via Ethernet
This chapter contains notes on networking via Ethernet. The networking of several panels via
Ethernet is only possible for the FPA-5000. The FPA‑1200 can be networked with up to three
remote keypads (FMR-5000) via Ethernet.
After installing the panels, various network settings must be made at the panel controller in
order to set up the network.
Notice!
Default settings that are to be used for default configurations are provided both for IP
settings and for redundancy settings for redundancy with the Rapid Spanning Tree Protocol
(RSTP). Changes may only be made by trained specialist personnel. Competent knowledge of
networking and protocols is essential! Permission level 4 is required for changes to the
network settings of a previously configured panel.
7.1
IP settings
To modify values for Ethernet settings or to configure these for the first time, select in the
start menu:
1.
Configuration
2.
Network. The Configuration IP screen is displayed.
3.
Activate the checkbox Use Ethernet settings.
4.
Select IP settings. The values for IP address, network screen, default gateway, multicast
address and port number are indicated. When you commission the panel controller for
the first time, all values are set to "0".
5.
Select Default settings to overwrite these values with the default settings saved in the
panel controller (recommended!). The IP address in this case corresponds to the stored
default IP address, the last number of which matches the rotary switch number (RSN)
that was set during installation at the panel controller.
6.
If the planned configuration requires a change to the default values:
Touch the field containing the value to be changed. Use the arrow keys on the operating
panel to select the desired numbers and modify the values using the number keys on the
alphanumeric keypad.
Or:
Touch the Change field. Touch the field containing the number block to be changed. Use
the arrow keys on the operating panel to select the desired numbers and modify the
values using the number keys on the alphanumeric keypad.
Touch OK to apply the changes or Cancel to discard the changes. You are returned to the
initial Configuration IP screen.
7.
Select OK to apply the changes to the IP settings or Cancel to discard the changes. You
8.
Select OK to confirm application of the Ethernet settings (Use Ethernet settings) or
are returned to the Configure Ethernet screen.
Cancel to exit the screen without activating the Ethernet settings.
Notice!
Changes to Ethernet settings take effect after restarting the panel.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
38
7.2
en | Networking via Ethernet
Panel Controller
Ethernet redundancy
Depending on the topology of the network, it may be necessary to select a redundancy
protocol. The default setting for the redundancy mode is none.
To specify a redundancy mode, go to the start menu and select:
1.
Configuration
2.
Network. The Configuration IP screen is displayed.
3.
Activate the checkbox Use Ethernet settings.
4.
Select Ethernet redundancy
5.
Select the redundancy type from: Dual homing, RSTP or none.
6.
Select OK to apply the change to the redundancy mode or Cancel to discard the changes.
You are returned to the Configure Ethernet screen.
7.
Select OK to confirm application of the Ethernet settings (Use Ethernet settings) or
Cancel to exit the screen without activating the Ethernet settings.
Notice!
The change to the redundancy mode takes effect after restarting the panel.
RSTP settings
In the case of redundancy via RSTP, additional settings need to be made.
Notice!
Default settings that are to be used for default configurations are provided for the RSTP
parameters. Changes may only be made by trained specialist personnel. Competent
knowledge of networking and protocols is essential! Permission level 4 is required for
changes to the RSTP parameters of a previously configured panel.
To modify the parameters for redundancy via RSTP or to configure these for the first time:
1.
Select RSTP as the redundancy type.
2.
Select Set parameters ... The values for bridge priority, hello time, maximum age and
forward delay are indicated. When you commission the panel controller for the first time,
all values are set to "0".
3.
Select Default settings to overwrite these values with the default settings saved in the
panel controller (recommended!).
4.
If the planned configuration requires a change to the default values:
Touch the field containing the value to be changed. Use the arrow keys on the operating
panel to select the desired numbers and modify the values using the number keys on the
alphanumeric keypad. If the values are outside of the defined minimum or maximum
values, the changes are not applied or a warning is displayed. If the values are
inconsistent, a formula appears indicating the corresponding dependencies of the values
as they relate to one another.
5.
Select OK to apply the changes to the RSTP parameters or Cancel to discard the
changes.
Notice!
Changes to RSTP parameters take effect after restarting the panel.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
7.3
Networking via Ethernet | en
39
Diagnostics
Diagnostics information and help materials for pinpointing problems in a network can be
found under menu item Diagnostics - Network. Information is provided on the following
topics:
–
Routing table
Information concerning the accessibility of all nodes within the system network via the
respective interface.
–
Ethernet ports
Information concerning different parameters and the status of the two Ethernet
interfaces available at the panel controller.
–
Send ping command
Sending of a ping command to a specific IP address to check the availability of other
nodes in the network.
–
Consistency check
The check performed determines whether the Ethernet configuration from FSP-5000-RPS
corresponds to the configuration entered at the panel controller. In the event of
discrepancies, a fault message is displayed.
–
Ethernet redundancy
Information concerning the type of redundancy configuration (RSTP or dual-homing). In
the case of redundancy via RSTP, the RSTP parameters of the RSTP panel and those of
the root bridge are displayed.
Further information can be found in Network services, page 65.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
40
8
en | Remote keypad
Panel Controller
Remote keypad
In the FSP-5000-RPS programming software, the address of a panel to which a connection is
automatically made from the remote keypad can be entered in the dialog regarding the node
of the remote keypad. In addition, further panels with which a connection can be made can
also be assigned.
It is not possible to log out of the automatically assigned connection. A connection can be
established with other panels without any further queries.
8.1
Operation and display
The prerequisite for operating a remote keypad is that an operator with an access
authorization > 1 is logged in. If an operator with access authorization = 1 is logged in, no
LEDs are activated and no messages displayed. If no operator is logged in, only the standby
screen is displayed.
Notice!
It is possible to specify in the FSP-5000-RPS programming software that messages are to be
displayed on the remote keypad, even if no operator is logged in. In this case the operation of
all functions is possible with permission level =1.
If the remote keypad is not connected to a panel, the following symbol is displayed on the
standby display and in the status bar:
Notice!
In the FSP-5000-RPS programming software, a time span can be specified after which an
operator who is logged in to the panel controller is logged out.
The following functions cannot be executed from the remote keypad via a remote connection:
–
LED, foil, display and display touch test
–
Adjust touch screen
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
9
Alarm | en
41
Alarm
Notice!
Information on how to handle a fire alarm can be found in Fire alarm, page 47.
This chapter contains information about the following points:
–
Types of alarm, page 41
–
Entry delays, page 41
–
Day and night mode, page 42
–
Alarm message to the panel, page 43
Refer to theFire alarmchapter for the following topics:
–
Acknowledging a message, page 47
–
Switching off internal buzzer, page 47
–
Switching external signaling devices on and off, page 48
–
Resetting external signaling devices and transmission devices, page 48
–
Triggering fire verification, page 48
–
Resetting alarm message, page 50
–
Bypassing detectors, page 50
Notice!
Depending on the configuration, the manner in which alarm displays are shown and handled
in this guide may differ from the guide on the system.
9.1
Types of alarm
On the panel controller, a distinction is made between the following types of alarm:
–
Fire
–
Heat (heat)
–
Smoke
–
Water
–
Supervisory
Depending on the configuration, external transmission devices (e.g. fire department),
notification appliances (e.g. sirens and/or strobes) and fire protection systems (e.g. sprinkler
systems, fire doors) are activated.
Notice!
If an alarm delay is set for the detector triggering the alarm, the alarm signal is not
transmitted immediately and the message can be checked; see Entry delays, page 41.
9.2
Entry delays
To prevent false alarms, it is possible to delay the transmission of the first alarm signal. The
transmission device to the fire department is not activated in this case. During the delay, the
message can be checked to ensure it is correct.
The FSP-5000-RPS programming software can be used to program various strategies for
avoiding false alarms. These strategies are principally used in fire detectors but can also be
assigned to any other detector, depending on how it is configured.
The alarm delays that can be shown in the panel controller display are explained below.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
42
en | Alarm
Panel Controller
Alarm verification
When the alarm message is acknowledged on the panel controller, a time to investigate is
started. During this time, the message in the place where the detector generating the alarm is
located must be checked to ensure it is correct. The duration of the verification time can be
freely configured for every detector. See also Fire alarm, page 47 and Triggering fire
verification, page 48.
If it is determined during the test that the alarm is genuine, an alarm can either be triggered
manually or by activating a manual call point. The transmission device to the fire department is
activated.
Depending on the configuration, a pre-alarm is displayed for the following alarm delays:
–
Intermediate alarm storage
If a detector with intermediate alarm storage triggers an alarm, this is displayed as a prealarm on the system. The transmission device to the fire department is not activated. The
detector generating the alarm is reset after the first signal.
The pre-alarm becomes a main alarm if the same detector triggers an alarm signal again
within a set time. The time until a main alarm is triggered is shown on the display. The
transmission devices and signaling devices are activated.
–
Dual-detector dependency
If a detector triggers an initial alarm within a dual-detector dependency, then this is
displayed on the system as a pre-alarm. The transmission device to the fire department is
not activated. The detector generating the alarm is reset after the first signal.
The pre-alarm becomes the main alarm if a second detector in the same logical zone
triggers an alarm. The transmission devices and notification appliances are activated.
–
Dual-zone dependency
If a detector triggers an initial alarm within a dual-zone dependency, then this is displayed
on the system as a pre-alarm. The transmission device to the fire department is not
activated. The detector generating the alarm is reset after the first signal.
The pre-alarm becomes the main alarm if a second detector in a different logical zone
triggers an alarm. The transmission devices and signaling devices are activated.
9.3
Day and night mode
Notice!
Depending on the configuration, the manner in which the difference between day and night
mode is displayed may differ from that on the system.
Depending on the configuration, an incoming alarm is handled differently in day and night
mode:
Night mode
Night mode has the highest security level. Depending on the configuration, the alarm message
is generally transmitted to the fire department without a delay.
Signaling devices (e.g. sirens) and transmission devices to the fire department or fire
protection systems are activated.
If the transmission device to the fire department is activated, the "Transmission Device
activated" LED display lights up red:
Depending on the configuration, a detector in night mode triggers a pre-alarm if intermediate
alarm storage is used as an alarm delay for this detector.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Alarm | en
43
Day mode
Notice!
Depending on the security level in question, not all detectors can be switched to day mode.
Depending on the configuration, a distinction is made between the following possible alarm
delays in day mode:
–
Alarm verification
–
Pre-alarm
A pre-alarm is displayed for the following alarm delays:
–
Intermediate alarm storage
–
Dual-detector dependency
–
Dual-zone dependency
For a detailed description of the various alarm delays, see Entry delays, page 41.
–
Internal alarm
An alarm that is reported to the panel in day mode. No transmission devices to the fire
department are activated.
9.4
Alarm message to the panel
The following description has been written on the basis of a sample fire alarm message.
9.4.1
Optical and acoustic signals
–
The red alarm signal light on the LED display lights up.
–
An internal buzzer sounds; see also Switching off internal buzzer, page 47.
–
Depending on the configuration, sounders and/or visual notification appliances (e.g.
sirens, strobes) are activated.
If the transmission device to the fire department is activated, the "Transmission Device
activated" signal light lights up red.
9.4.2
Displaying the detector zones in alarm state
The number of messages in question is displayed on the status bar.
Notice!
First of all, the logical zones in which one or more detectors have triggered an alarm are
listed. To display the individual detectors, select the logical zone you require. See also
Displaying the individual detectors in a logical zone, page 45.
The individual messages are shown in the display:
–
List fields with black background: unacknowledged alarm messages
–
List fields without distinction: acknowledged alarm messages
Logical Zones
Notice!
A maximum of four alarm messages can be displayed on the display simultaneously. Only
fields that can be operated are displayed (e.g. Acknowledge and Reset).
If more than four alarm messages have been received, scroll through the list in order to display
the next messages (see Scrolling through lists, page 27).
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
44
en | Alarm
Panel Controller
Notice!
The latest message is always displayed at the end of the list.
Display during an alarm
The buttons located beneath the alarm message on the display can be used to initiate the
corresponding actions:
Acknowledge
Signals off
Signals on
Reset
–
Acknowledge: Touch this button to acknowledge all of the alarm messages shown on the
–
Signals off: Touch this button to switch off activated external notification appliances; see
display; see also Acknowledging a message, page 47.
also Switching external signaling devices on and off, page 48.
–
Signals on: Touch this button to switch on deactivated external notification appliances;
see also Switching external signaling devices on and off, page 48.
–
Reset: Touch this button to reset all of the alarm messages shown on the display; see
also Resetting alarm message, page 50.
9.4.3
Sequence of the alarm messages
The messages are displayed in chronological order.
–
The newest alarm message of a logical zone is always displayed at the end of the list.
–
The first and oldest alarm message of a logical zone is displayed at the beginning of the
list. The next three messages are displayed as you scroll through the list.
Notice!
30 seconds after the last entry (e.g. after scrolling through the list), the first and oldest alarm
is displayed at the beginning of the list again.
9.4.4
Information about logical zones in the alarm state
The alarm message contains information about:
–
The element category
–
The message type
–
The address of the detector group
–
The number of detectors that have triggered an alarm in the respective logical zone
–
The message number
–
Depending on the configuration, additional information such as the installation location
Example:
Fire
#001
Zone
00005
Office 1
(6)
Message type
The message type Fire is reported.
Depending on the configuration, the message type may be defined more specifically, e.g. Fire
PAS for a fire alarm with alarm verification.
Address of logical zone
00005: the fifth logical zone triggered the first fire alarm.
Number of detectors
(6): In the fifth logical zone (00005), six detectors (6) triggered a fire alarm.
For logical zones that only consist of one element, no number of detectors is displayed.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Alarm | en
45
Notice!
Depending on the configuration of the system, either the logical or physical address of the
detector is displayed.
Message number
The alarm messages are numbered chronologically.
The message number in the second line indicates the sequence in which the alarm messages
arrived.
#001: The first alarm message that came in.
Depending on the configuration, additional information is displayed in the second line, such as
the installation location of the logical zone.
9.4.5
The newest message
The latest message is always displayed at the end of the list.
The message number (e.g. #008) of the latest message indicates the total number of logical
zones in which one or more detectors have triggered an alarm.
9.4.6
Displaying the individual detectors in a logical zone
To display the individual detectors in a logical zone, select the logical zone you require.
The alarm messages for the individual detectors are listed.
9.4.7
Information about individual detectors
Each alarm message contains information about:
–
The element category
–
The message type
–
The detector address
–
The message number
–
Depending on the configuration, additional information such as the installation location
Example:
Fire
#002
Detectors
00005 - 004
Office 1
Message type
Refer to Information about logical zones in the alarm state, page 44 for information on the type
of message.
Message address
In this example, the following detector has triggered a fire alarm:
0005 - 004: the fourth detector (004) in the fifth logical zone (00005).
If the detector number, in this case (004), is not displayed, this is the alarm message for the
logical zone.
Notice!
Depending on the configuration of the system, either the logical or physical address of the
detector is displayed.
Message number
For information on the message number (#002), see Information about logical zones in the alarm
state, page 44.
Depending on the configuration, additional information is displayed in the second line, such as
the installation location of the detector or the detector type.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
46
en | Alarm
Panel Controller
To display more information about an alarm message, see Displaying additional information,
page 46.
9.4.8
Displaying additional information
Notice!
By way of example, an action text can be entered for every detector type in the FSP-5000-RPS
programming software.
To display further information about the individual detectors, select the alarm message you
require.
The following information is displayed:
–
Element category
–
Message type
–
Date and time of the message
–
Physical and logical addressing of the detector
–
Only for LSN detectors: specification of the detector type
–
Action text (depending on the configuration)
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
10
Fire alarm | en
47
Fire alarm
Notice!
Detailed information about types of alarms, alarm delays and the panel controller display can
be found in Alarm, page 41.
This chapter contains information about the following points:
–
Acknowledging a message, page 47
–
Switching off internal buzzer, page 47
–
Switching external signaling devices on and off, page 48
–
Resetting external signaling devices and transmission devices, page 48
–
Triggering fire verification, page 48
–
Resetting alarm message, page 50
–
Bypassing detectors, page 50
Signaling fire alarms
A fire alarm is signaled optically and acoustically on the panel through:
–
Displaying the logical zones on the display
–
Lighting up the "Alarm" LED display
–
An internal buzzer sounds on the system.
Notice!
Alarm messages have the highest priority compared with all other message types. If a fire
alarm is reported, the system switches automatically to alarm indication.
10.1
Optical and acoustic signals
–
The red alarm signal light on the LED display lights up
–
An internal buzzer sounds; see also Switching off internal buzzer, page 47.
–
Depending on the configuration, sounders and/or visual notification appliances (e.g.
sirens, strobes) are activated.
If the transmission device to the fire department is activated, the Transmission Device
activated LED display lights up red:
10.2
Acknowledging a message
There are two ways to acknowledge messages:
–
Select Acknowledge. Only those alarm messages which are visible in the display are
acknowledged.
–
Select a message and then press Acknowledge. Only the selected message is
acknowledged.
Notice!
If Go to Acknowledge is displayed, select this field in order to display the messages that have
not yet been acknowledged.
10.3
Switching off internal buzzer
Press the following key to temporarily switch off the internal buzzer:
The internal signal tone is switched off.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
48
en | Fire alarm
Panel Controller
Switching external signaling devices on and off
10.4
Sounders and optical signaling devices which have been activated can be switched off.
4
Select Signals off.
The sounder and/or optical signaling device is switched off. The text in the field changes
to Signals on.
Notice!
On the next alarm message, all signaling devices that have been switched off are switched
back on automatically.
4
To switch the notification appliance back on, select Signals on.
The signaling devices are switched on again.
Resetting external signaling devices and transmission devices
10.5
4
To reset control or transmission devices, select Control in the status bar
Notice!
The display automatically changes back to alarm indication after 30 seconds. To return to the
alarm indication before 30 seconds have elapsed, select Fire.
4
Select the signaling device.
Only the activated signaling devices are displayed.
1.
Select one or more list fields.
The list field is marked.
2.
Select Reset.
The control units are reset to the initial state.
In the Control field on the status bar, the number of control elements is reduced by the
number of reset elements.
To reset transmission devices, carry out the same steps, but select Transmission device in
step 1.
Triggering fire verification
10.6
Alarm verification
10.6.1
The transmission of the alarm is delayed. The alarm message must be checked to ensure it is
correct in the place where the detector generating the alarm is located.
An internal buzzer sounds on the panel. The signaling devices (e.g. sirens) and transmission
device to the fire department are not activated.
The time for checking the fire alarm is called the time to investigate. The duration of this time
can be different for every logical zone. The time to investigate is started if the fire alarm is
confirmed on the panel within the time to acknowledge.
Caution!
!
If another fire alarm is reported during the time to investigate, all alarm messages are
transmitted to the fire department. The time to investigate is canceled.
If a real fire alarm is detected during the on-site inspection, the alarm must be forwarded to
the fire department; see Triggering alarm manually, page 49. Alternatively, a manual call point
can be triggered at the location.
If it is a false alarm, the triggering detector can be reset or bypassed; see resetting alarm
message or bypassing detectors.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Fire alarm | en
49
Caution!
!
Alarm messages from bypassed detectors are no longer displayed; only faults in these
detectors are displayed.
Starting time to investigate
10.6.2
Caution!
!
If another alarm is triggered during the verification time (external alarm), the verification time
is suspended until the queued fire alarms are reset.
If there is the possibility of testing, the following time spans are displayed. The counters count
to zero:
–
Time to acknowledge The alarm must be confirmed within the specified time span.
–
Time to investigate The alarm must be verified within the specified time span. This time
can be specified differently for each logical zone or detector.
–
Reset possible in : Time span after which the detector can be reset. For information on
resetting, see Resetting alarm message, page 50.
Caution!
!
If the time to acknowledge or the time to investigate is exceeded, the alarm is immediately
forwarded to external stations.
To initiate alarm verification, select Acknowledge within the time shown to confirm the alarm.
Caution!
!
If the alarm is not confirmed within this time, it will be forwarded to external stations.
The time to investigate will be displayed. The alarm verification is initiated.
Test the fire alarm onsite within the specified time.
Caution!
If a second alarm is triggered during the alarm verification, all alarm messages are
!
automatically forwarded to external stations.
If, after conclusion of the alarm verification, a second alarm comes in — assuming alarm
verification is also possible for this alarm — then a time to investigate is initiated automatically
again.
10.6.3
Triggering alarm manually
Caution!
!
If, during the check, a real fire alarm is detected, then this alarm to the panel must be
manually forwarded to external stations such as the fire department. Alternatively, a manual
call point can be triggered at the location.
1.
To forward the alarm to external stations, select Manual alarm.
2.
Select OK to confirm the operation.
The alarm is forwarded to the fire department:
In the LED display, the "Transmission Device activated" signal light turns red.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
50
en | Fire alarm
10.7
Panel Controller
Resetting alarm message
Notice!
The detector can only be reset once the Reset time has elapsed, generally after half of the
verification time.
When an element is reset, its initial status is restored. The activation of transmission devices
such as fire department or extinguishing devices is reset.
Depending on the configuration, three different variants are offered for resetting:
–
Standard
Resetting all message types of the same message type:
All types of messages within the selected message type, such as Fire, are reset.
–
–
Resetting all elements that are not in the normal state
Displaying a submenu with four different selection options
Each displayed component can be reset individually:
–
This panel
To reset all elements that are not in the normal state
–
All elements in this event
to reset all elements that have triggered a fire alarm, for example
–
Logical zone
a list of the logical zones is displayed
–
Detector
a list of the detectors is displayed
To reset an alarm message, select either
–
Reset on the message display
or
–
The alarm message and Reset in the detailed view:
Depending on the variant that is offered (see above), all elements that are not in the
alarm state or all types of message within the same message type are reset.
If different elements are offered for resetting:
1.
Select an element. At the menu items Zone and Detector, a list with all the logical zones
and detectors concerned appears.
2.
Select the list field you require. Refer to Scrolling through lists, page 27 for information on
how to scroll forward and backward through a list.
The list field is marked.
3.
Select Reset.
The selected element / element group is reset.
TEXT
R
If a list field is marked with an R, the process of resetting is not yet complete for this element.
If an element cannot be reset, it will continue to be displayed in the list.
After the successful resetting of all elements, the standby display is displayed.
10.8
Bypassing detectors
To bypass a detector that has triggered an alarm:
1.
Select the alarm message you require.
2.
Select Bypass.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Fire alarm | en
51
Notice!
The system does not transmit any information as to whether it was possible to bypass the
selected element. To monitor the operation, please check the element.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
52
en | Fault message
Panel Controller
Fault message
11
This chapter contains information about the following points:
–
Calling up fault indication, page 52
–
Trouble message on the panel, page 52
–
Switching off internal buzzer, page 47
–
Resetting malfunction message, page 55
–
Isolating an element, page 55
Calling up fault indication
11.1
Notice!
If a fire alarm is reported, the system automatically switches to alarm indication. To return to
the fault indication, select Fault on the status bar. In the event of a fire alarm, the display
automatically switches back to the alarm indication after 30 seconds.
To display the fault messages from the alarm indication or any other menu, select the
following on the status bar:
–
Fault: A list of all reported fault types and the number of faulty elements are displayed.
–
Status: A list of all current messages, grouped by message type, is displayed. The number
of elements is also given in each case.
To display the fault messages, select the message category you require — in this case,
Fault.
0
0
8
0
Fire
Control
Trouble
Bypass
Status
Caution!
!
If a message does not have to be reset, it is removed from the display as soon as the fault has
been rectified.
Notice!
If individual elements that are combined with other elements in a group are malfunctioning,
the respective element group is displayed first of all. To display the individual elements,
select the element group you require. See also Displaying individual elements of an element
group, page 54.
11.2
11.2.1
Trouble message on the panel
Acknowledging a message
There are two ways to acknowledge messages:
–
Acknowledging all displayed messages: Select Acknowledge.
–
Acknowledging an individual message: First select the message and then press
Acknowledge.
Element groups
Logically addressed logical zones are displayed in a list.
List fields with black background indicate unacknowledged fault messages.
List fields without distinction indicate acknowledged fault messages.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Fault message | en
53
Notice!
A maximum of four fault messages can be displayed on the display at any time. Only fields
that can be operated are displayed (e.g. Acknowledge and Reset).
To display further fault messages, scroll down through the list. Refer to Scrolling through lists,
page 27 for information on how to scroll through a list.
The next four fault messages are displayed.
11.2.2
Sequence of the trouble messages
The messages are displayed in chronological order.
Notice!
15–30 seconds after the last entry (e.g. after scrolling through the list), the first and last fault
message is displayed at the beginning of the list again.
11.2.3
Information about malfunctioning element groups
The trouble message contains information about:
–
Element category
–
Message type
–
Address of the element group
–
Number of individual elements that have caused a fault in the respective element group
–
Message number
–
Additional information (e.g. the installation location)
Example:
Fault
#001
Zone
00005
Office 1
(6)
Element category:
Different detectors in one logical zone
Message type:
Fault
Address of element groups 00005: The fifth logical zone caused the first fault.
Number of individual
(6): In the fifth logical zone (00005), six detectors caused a
elements
fault. For element groups that only consist of one element, the
number of elements is not displayed.
Message number
The fault messages are numbered chronologically.
The message number in the second line indicates the sequence
in which the fault messages were received.
001: The first and oldest fault message received.
Installation location of the
Office 1
logical zone
Notice!
Depending on the configuration of the system, either the logical or physical address of the
element is displayed.
11.2.4
The newest message
The newest message is displayed at the end of the list.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
54
en | Fault message
Panel Controller
Notice!
15–30 seconds after the last entry (e.g. after scrolling through the list), the first and oldest
fault message is displayed at the beginning of the list again.
11.2.5
Displaying individual elements of an element group
To display the individual elements in an element group, select the element group you require.
The fault messages of the individual elements are listed.
11.2.6
Information about individual elements
The trouble message contains information about:
–
Element category
–
Message type
–
Element address
–
Message number
–
Additional information (e.g. the installation location)
Example:
Fault
#002
Transmission device
00026-
004
Cafeteria
Element category:
Transmission device
Message type:
Fault
Element address
The following transmission device has caused a fault:
00026 - 004: The fourth transmission device (004) in the 26th
group (00026).
Message number
The fault messages are numbered chronologically.
The message number in the second line indicates the sequence
in which the fault messages were received.
002: The second fault message to be received.
Installation location of the
Cafeteria
element
Notice!
Depending on the configuration of the system, either the logical or physical address of the
element is displayed.
To display more information about an alarm message, see Displaying additional information,
page 54.
11.2.7
Displaying additional information
To display further information about the individual elements, select the fault message you
require.
Notice!
The information displayed is entered in the FSP-5000-RPS programming software.
The following information is displayed:
–
Element category
–
Message type
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Fault message | en
–
Date and time of the message
–
Physical and logical addressing of the element
–
Only for LSN detectors: specification of the detector type
–
Action text (depending on the configuration)
55
Select OK to return to the list of all fault messages. Reset, see Resetting malfunction message,
page 55.
Block, see Isolating an element, page 55.
Signals
11.2.8
Optical signals
An internal buzzer sounds on the panel and the "fault" signal light turns yellow.
Depending on the type of fault, an additional yellow signal light lights up (see also Display
elements, page 20):
–
Fault System
–
Fault Transmission Device
–
Fault Signals
Acoustic signal
An internal signal tone sounds on the system.
To temporarily switch off the internal buzzer:
Press the "Signal tone off" key.
The internal signal tone is switched off.
Resetting malfunction message
11.3
Caution!
!
If a message does not have to be reset, it is removed from the display as soon as the fault has
been rectified.
Depending on the configuration, three different variants are offered for resetting; see Resetting
alarm message, page 50.
There are two ways to reset a fault message:
–
Select Reset in the message display or
–
Select the fault message and then press Reset in the detailed view
The selected element/element group is reset.
If a list field is marked with an "R", the process of resetting is not yet complete for this
element.
TEXT
R
If an element cannot be reset, it will continue to be displayed in the list.
After the successful resetting of all elements, the standby display is displayed.
11.4
Isolating an element
In order to isolate an element that has caused a fault:
1.
Select the fault message you require.
2.
Select Block.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
56
en | Fault message
Panel Controller
Caution!
!
The system does not transmit any information as to whether it was possible to isolate the
selected element. To monitor the operation, check the element.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Bypass | en
57
Bypass
12
This chapter contains information about the following points:
–
Bypassing and un-bypassing elements, page 57
–
Displaying and un-bypassing bypassed element groups, page 58
–
Displaying list of all bypassed elements, page 58
–
Bypassing/Un-bypassing buzzer, page 59
Warning!
!
Bypassed detectors: Alarm messages from bypassed detectors are no longer displayed, only
faults.
Isolated detectors: Isolated detectors are not analyzed.
12.1
Bypass
Menu overview
-> Bypass
-> Show bypassed
Block
Block
Select by
devices
number
NAC
Transmission
Bypass buzzer
Printer
HVAC
Doorholder
Extinguishing
Annunciator
device
Detector
Logical zone
system
Bypass group
More...
-> Control
Interface
element
12.2
module
Bypassing and un-bypassing elements
Select the element you require in the submenu.
Notice!
Partly bypassed elements, such as loops or bypass groups, can be displayed and completely
bypassed; see Displaying and un-bypassing bypassed element groups, page 58.
Notice!
The menu structure may be different depending on the configuration in FSP-5000-RPS.
Example:
To bypass a detector, select the following in the start menu:
1.
Bypass Block
2.
Bypass
3.
Detector
Various sorting criteria are displayed. See also Working with lists, page 27.
4.
Select a selection criterion, e.g. By description.
A list of the detectors is displayed. Refer to Scrolling through lists, page 27 for information
on how to scroll forward and backward through the list.
5.
Select the required list fields.
The list fields are marked.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
58
en | Bypass
Panel Controller
6.
Select Bypass.
The selected elements are bypassed.
In the Bypass field on the status bar, the number of bypassed elements is increased by
two elements.
To remove the bypass from the elements, repeat all previous steps but select Un- bypass in
step 6.
Notice!
Depending on the configuration and the structure of the panel, it is possible that signaling
devices cannot be bypassed individually but only all at once. In this case, the NACAll list field
is offered in step 4 instead of the selection list.
12.3
Displaying and un-bypassing bypassed element groups
1.
There are two ways to display all partly or completely bypassed loops, logical zones etc.:
–
Select Bypass on the status bar
–
Select Bypass Block in the start menu.
A list of various states is displayed. Or
2.
Select either Bypassed or Bypass and then Show bypassed devices.
A list of various element categories is displayed. The listed number displays the number
of bypassed elements or element groups in the relevant element category.
3.
Select the list field you require, e.g. logical zone.
4.
Select:
–
Partly bypassed to display all partly bypassed logical zones
–
Completely bypassed to display all completely bypassed logical zones
Depending on which option you select, all partly bypassed or fully bypassed logical zones
will be displayed. The number in parentheses, e.g. (5) specifies the number of bypassed
elements.
To remove the bypass from all elements in one or more logical zones, select the logical
zone you require and select Un- bypass.
12.4
Displaying list of all bypassed elements
There are two ways to display a list of all bypassed elements:
12.4.1
–
Using the menu, page 58
–
Via the status bar, page 59
Using the menu
To display a list of all bypassed elements, select the following in the start menu:
1.
Bypass Block
2.
Bypass
3.
Show bypassed devices
A list of various element categories is displayed. The listed number displays the number
of bypassed elements or element groups in the relevant element category.
4.
Select the element category you require, e.g. Detector .
A list of all bypassed detectors is displayed:
To un-bypass bypassed elements:
1.
Select the element you require.
2.
Select Un- bypass.
The element is un-bypassed.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
12.4.2
Bypass | en
59
Via the status bar
To display a list of all bypassed elements:
1.
Select Bypass from the status bar.
A list of various states is displayed.
2.
Select Bypassed.
A list of various element categories is displayed. The listed number displays the number
of bypassed elements or element groups in the relevant element category.
3.
Select the list field you require, e.g. Detector.
A list of all bypassed elements is displayed.
To un-bypass bypassed elements:
12.5
1.
Select the elements you require.
2.
Select Un- bypass.
Bypassing/Un-bypassing buzzer
In order to prevent an acoustic warning tone being sent to the panel during maintenance
work, for example, the panel's internal buzzer can be permanently bypassed.
To bypass the internal buzzer, select the following in the start menu:
1.
Bypass Block
2.
Bypass
3.
More...
4.
Bypass buzzer
The buzzer is bypassed and the text on the user interface changes to Unbypass buzzer.
To remove the bypass from the buzzer, select Unbypass buzzer in step 4.
Notice!
If you switch the internal buzzer off permanently, no acoustic signal will sound on the panel in
the event of an alarm or fault!
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
60
en | Isolate
Panel Controller
Isolate
13
This chapter contains information about the following points:
–
Isolating and de-isolating elements, page 60
–
Displaying list of all isolated elements, page 60
Caution!
!
Bypassed detectors: Alarm messages from bypassed detectors are no longer displayed, only
faults.
Isolated detectors: Isolated detectors are not analyzed.
13.1
Bypass
Menu overview
-> Bypass
Show blocked devices
Block
Select by
Block Group
Printer
Strobe
HVAC
Doorholder
Detector
Extinguishing
Annunciator
number
Block
-> Sounder
Transmission device
system
Logical zone
More...
-> Control
Interface
element
13.2
module
Isolating and de-isolating elements
Select the element you require in the submenu.
Example:
To isolate a detector, select the following in the start menu:
1.
Bypass Block
2.
Block
3.
Detector
Various selection criteria are displayed. See also Working with lists, page 27.
4.
Select a selection criterion, e.g. By description.
A list of the detectors is displayed. Refer to Scrolling through lists, page 27 for information
on how to scroll forward and backward through the list.
5.
Select the required list fields.
The list fields are marked.
6.
Select Block.
The selected elements are isolated.
To de-isolate the elements again, repeat all previous steps but select Un- block in step 6.
C
A C after a detector means that this detector is part of a closed group and cannot be isolated
individually. In order to isolate a detector marked in this way, please select Logical zone in
step 3.
13.3
Displaying list of all isolated elements
There are two ways to display a list of all isolated elements:
–
Using the menu, page 61
–
Via the status bar, page 61
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
13.3.1
Isolate | en
61
Using the menu
To display a list of all isolated elements, select the following in the start menu:
1.
Bypass Block
2.
Block
3.
Show blocked devices
A list of various element categories is displayed. The listed figure indicates the number of
isolated elements or element groups in the relevant element category.
4.
Select the element category you require, e.g. Detector .
A list of all isolated detectors is displayed.
To de-isolate isolated elements:
1.
2.
Select the element you require.
Select Un- block.
The element is de-isolated.
13.3.2
Via the status bar
To display a list of all isolated elements:
1.
Select Bypass from the status bar.
A list of various states is displayed.
2.
Select Blocked.
A list of various element categories is displayed. The listed figure indicates the number of
isolated elements or element groups in the relevant element category.
3.
Select the list field you require, e.g. Detector .
A list of all isolated elements is displayed.
To de-isolate isolated elements:
1.
Select the element you require.
2.
Select Un- block.
The element is de-isolated.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
62
en | Diagnostics
14
Panel Controller
Diagnostics
This chapter contains information about the following points:
–
Element details, page 62: Diagnostic information about an LSN module and about
elements of a selected LSN module
–
Modules, page 63: Diagnostic information (software version) and hardware diagnostic
data about modules
–
Hardware, page 63 Information about released addresses, statistical data for the
transmission, and the execution of display tests
–
Panel Passport, page 65 Diagnostic information about the panel controller
–
LED Test on modules, page 65 Testing the LED display of modules
–
History log; see Maintenance – history log, page 77
–
Network services, page 65 Information on the availability of other nodes within the
system network
–
Voice alarm systems, page 68
Diagnostic information about a connected voice alarm system (VAS)
14.1
Menu overview
Diagnostics
14.2
-> Element details
Modules
Hardware
Panel passport
LED test on modules
History log
Network
VAS
Element details
To display diagnostic information about the elements in a particular module:
1.
In the start menu, select Diagnostics
2.
Element details
A list of the LSN modules is displayed.
Notice!
The numbers before the module names indicate the slot of the module on the panel.
1.
Select the list field you require.
On the display, various possibilities for selection are offered:
2.
Select:
–
All info for one element to display all diagnostic information about an element on
–
Info for element group to display particular diagnostic information about several
one loop of an LSN module.
elements of the selected LSN module.
–
Info for all elements on the module to display particular diagnostic information
about all LSN elements of the selected LSN module.
The subsequent procedure for all three selection possibilities will be presented by means
of an example. The other two possibilities deviate only slightly from this.
Example:
1. Select Info for element group.
A list of the elements of the selected LSN module is displayed.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Diagnostics | en
2.
63
Select the required list fields.
The list fields are marked.
3.
Select Yes.
A list of various data types is displayed.
4.
Select the field you require.
The field is marked.
The data of each selected element is requested.
5.
Select Start.
To cancel the operation, select Cancel.
A status bar appears.
14.3
6.
Select the arrow keys to display further information.
7.
Select Refresh to update data if necessary.
Modules
To display diagnostic information about a particular module:
1.
In the start menu, select Diagnostics
2.
Modules
Two different lists are offered.
3.
Select a list, e.g. By number. Refer to chapter Scrolling through lists, page 27 for
information on how to scroll through a list.
A list of all used modules is displayed.
4.
Select the list field you require.
A list of various information options is displayed:
–
Module passport
–
Module Compatibility
–
Module status
For an LSN module, the following selection fields are also offered:
5.
–
Module status and counters
–
Reset counters
Select the information option you require, e.g. Module status.
Diagnostic information about the module status is displayed.
A status bar appears.
6.
Select the arrow keys to display further information.
7.
Select Refresh to update data if necessary.
14.4
Hardware
14.4.1
Address cards
To display information about the released addresses:
1.
Select Diagnostics in the start menu.
2.
Hardware
3.
Address cards
The information is displayed.
A status bar appears.
14.4.2
4.
Select the arrow keys to display further information.
5.
Select Refresh to update data if necessary.
Display
Five different functions are offered:
–
LED test: Test the LED display.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
64
en | Diagnostics
Panel Controller
–
Key test: Test the operativeness of the membrane keypad.
–
Display test: Test the operativeness of the display.
–
Display touch test: Test the operativeness of the touch-sensitive surface.
–
Adjust touch screen (Calibration): Adjust the location precision when touching the touch
screen.
LED test
To test the LEDs in the LED display:
1.
In the start menu, select Diagnostics
2.
Hardware
3.
Display
4.
Select LED test.
For the duration of approx. five seconds, all LEDs on the LED display light up.
Key test
To test the functionality of the membrane keypad:
1.
In the start menu, select Diagnostics
2.
Hardware
3.
Display
4.
Key test
5.
Press one or more keys on the membrane keypad.
The selected keys on the membrane keypad are depicted on the touch screen.
If a key is pressed twice, this key is shown with a black background. Press the key again
to display it without distinction.
6.
Select Stop key test to end the foil test.
Display test
To test the operativeness of the display:
1.
In the start menu, select Diagnostics
2.
Hardware
3.
Display
4.
Select Display test.
Line by line, the display turns a dark color from the top to the bottom and then changes
again from black to white.
Display touch test
To test the functionality of the touch-sensitive surface:
1.
In the start menu, select Diagnostics
2.
Hardware
3.
Display
4.
Select Display touch test.
5.
Touch the touch screen.
A crosshair appears at the touched place.
Press the "back" function key to end the operation.
Adjust touch screen (Calibration)
To adjust the press precision when touching the touch screen:
1.
In the start menu, select Diagnostics
2.
Hardware
3.
Display
4.
Adjust touch screen
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Diagnostics | en
5.
14.4.3
65
Carry out the steps shown on the display.
Serial Interface
Select Serial interface to display the statistical data for the transmission.
14.4.4
CAN-Bus
Select CAN bus to display the status of the CAN interfaces.
14.5
Panel Passport
Select Panel passport to display the following diagnostic information:
14.6
–
Module
–
Address
–
CAN ID
–
Production date
–
BOM revision
–
PCBA material number
–
Material number
–
Software version
–
Build type
–
Build number
–
MAC Address
LED Test on modules
To test the LED display of selected modules:
1.
In the start menu, select Diagnostics
2.
LED test on modules
A list of various selection criteria is offered:
–
Select LED test all modules to test the LED display of all modules.
–
Select By number or By type to test the LED display of individual selected modules.
Example
To test the LED displays of an LSN 300 module:
1.
Select By type.
A list of all module types is displayed.
2.
Select the LSN 300 module.
A list of all LSN 300 modules is displayed.
3.
Select the list field(s) you require. The list fields are marked.
4.
Select Activate LEDs.
The LEDs are activated for the duration of approx. five seconds.
Notice!
The numbers before the module names indicate the slot of the module on the panel.
14.7
14.7.1
Network services
Routing table
To display routing information:
1.
In the start menu, select Diagnostics
2.
Network services
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
66
en | Diagnostics
Panel Controller
3.
Routing table
A table with routing information is displayed.
All networked nodes that can be reached via the node currently being operated and that are
recognized within the system network are displayed under Node.
CAN1 to USB1 designate the interfaces on the currently operated panel node. In this example,
it is the node 1 interfaces.
The type of interface on the panel node currently being operated is listed under interface.
The following interfaces can be designated:
–
CAN 1 interface
–
CAN 2 interface
–
Ethernet 1 (IP multicast or UDP tunnel)
–
Ethernet 2 (IP multicast or UDP tunnel)
–
Serial Interface
–
USB 1 interface
The number of nodes that need to be passed in order to reach the listed node is entered
under distance. For nodes that are directly reachable via IP multicast, the value is 1; for nodes
that are connected via other interfaces (e.g. CAN) to nodes reachable via IP multicast, the
value is increased in increments accordingly (e.g. connected via IP multicast + CAN1/CAN2,
value = 2).
A node number from 1 to 32 can be assigned to panels. All numbers above 240 (241-255) are
assigned dynamically and used, for instance, for an OPC server or a PC with FSP-5000-RPS
software.
14.7.2
Consistency check
Inconsistencies between the network settings configured in FSP-5000-RPS and those set in
the panel controller are displayed under Diagnostics - Network services Consistency check.
1.
In the start menu, select Diagnostics
2.
Network services
3.
Consistency check
Where inconsistencies are identifiable between the network settings saved in the panel
controller and those configured in FSP-5000-RPS, these are indicated. You can use the
arrow key on the display to alternate between displaying Problems of active
configuration: and Problems expected after restart:.
Problems of active configuration:
The table indicates inconsistencies between the network settings of the panel controller's
active configuration ("active") and the settings configured in RPS ("configured").
Problems expected after restart:
The table indicates inconsistencies between the network settings that have already been
configured on the panel but which do not take effect until restart ("saved") and the settings
configured in RPS ("configured").
14.7.3
Ethernet ports
To display a table listing the various parameters and the status of the two Ethernet ports:
1.
In the start menu, select Diagnostics
2.
Network services
3.
Ethernet ports
Information on Ethernet port 1 is displayed.
You can use the arrow key on the display to switch to details of Ethernet port 2.
To update the information displayed, select Refresh.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Diagnostics | en
67
Information on the following parameters is displayed in the table:
14.7.4
–
Port status
–
Link status: Checks the operativeness of the network cable
–
Speed: Speed of the network connection
–
#Tx Frames: Number of transferred data packages
–
#Rx Frames: Number of received data packages
–
Connected to: Indicates neighboring available node
Send ping command
To check the availability of other nodes in the network, a ping command can be sent to a
specific IP address:
1.
In the start menu, select Diagnostics
2.
Network services
3.
Send ping command
4.
Enter the IP address of the network node you wish to assess as regards availability and
select Send ping command.
To enter an IP address:
Touch the field containing the IP address. Use the arrow keys on the operating panel to
select the individual numbers and modify using the number keys on the alphanumeric
keypad.
Or:
Touch the Change field. Touch the field containing the number block to be changed. Use
the arrow keys on the operating panel to select the desired number and modify using the
number keys on the alphanumeric keypad.
If the addressed network node is accessible, a success message is displayed.
14.7.5
Ethernet redundancy
To display a list with details of the redundancy mode, RSTP parameters the root bridge and
local bridge, as well as information on the two Ethernet ports:
1.
In the start menu, select Diagnostics
2.
Network services
3.
Ethernet redundancy
A list with details of the following is displayed:
–
Redundancy mode
–
Root bridge/ local bridge:
–
–
Priority
–
MAC address
–
Hello time
–
Max. age
–
Forward delay
Ethernet 1/Ethernet 2 port:
–
Port role
–
Port status
Notice!
A competent knowledge of networking and protocols is essential to utilize this information!
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
68
en | Diagnostics
14.7.6
Panel Controller
Condition Monitoring
Notice!
The Condition Monitoring feature is only available in Germany together with a service
agreement with ST-BT.
If the Condition Monitoring feature was activated via the remote programming software
FSP-5000-RPS data of relevant LSN devices and FPA-5000 modules are collected and sent to a
central management server system (CMS) where they can be analyzed in order to offer
customers preventive services. In the Condition Monitoring
window you find information concerning the feature:
1.
In the start menu, select Diagnostics
2.
Network services
3.
Condition Monitoring
A list with information concerning the Condition Monitoring feature is displayed:
–
State of Condition Monitoring: shows if the Condition Monitoring feature was activated
in the programming software FSP-5000-RPS. In case that Condition Monitoring was
activated temporarily the remaining time of the activation is shown (Timeout of
temporary transfer).
–
State of last transfer: State of the last transfer of data from LSN devices connected to
the fire panel to the Condition Monitoring server (OK/Failed/Authentication failed)
–
Date of last transfer: Date and time of the last data transfer from an LSN device
connected to the fire panel to the Condition Monitoring Server.
–
Server IP address: IP address of the server collecting Condition Monitoring data.
–
Server port: Port number of the server collecting Condition Monitoring data.
To check whether the Ethernet connection to the central management server is still active
choose Check server connection. The state of the connection to the central management
server is shown.
14.8
Voice alarm systems
Two different kinds of voice alarm systems can be connected to the FPA-5000 and FPA-1200:
–
Plena voice alarm system
–
Praesideo voice alarm system
The diagnostic information displayed depends on the voice alarm system configured for the
FPA-5000/FPA-1200 network.
To display a list of all connected voice alarm systems that are used for voice evacuation:
1.
In the start menu, select Diagnostics
2.
VAS
A list of the available voice alarm systems is displayed.
To display information on an available Plena voice alarm system:
Touch one of the systems displayed in order to select it. The following information is
displayed:
–
Trouble (yes/no)
–
Emergency (yes/no)
–
Failure (yes/no)
–
Internal monitoring (yes/no)
–
Supervision time (sec).
–
Boot-up phase is finished (yes/no)
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Diagnostics | en
Panel Controller
–
Failure at controller (yes/no)
–
Failure at router (yes/no)
69
To display information on an available Praesideo voice alarm system:
Touch the voice alarm system displayed in order to select it. The following information is
displayed:
–
Connection status: Shows whether an IP connection to the Praesideo voice alarm system
exists.
–
Praesideo status: In case of trouble please check the Praesideo voice alarm system.
–
Licence: Shows if a valid license key is inserted for the Praesideo system (“VAS” or
“OPC/VAS”). If no valid license key is available, the remaining time until the disconnection
of the connection to Praesideo is displayed.
–
Trigger configuration:
Mismatch: A VAS Virtual Trigger programmed in the FPA-5000 configuration cannot be
matched to an equivalent trigger on the Praesideo side. Please check the mapping of the
virtual VAS triggers/virtual control inputs configured in the FSP-5000-RPS programming
software and the Praesideo configuration.
–
Compatibility:: Shows whether the version of the connected Praesideo system is
released for the connection to an FPA-5000/FPA-1200. If a warning is displayed please
check the version of the Praesideo system.
–
Line supervision fault counter: Shows the number of connection errors to the Praesideo
system until the last reboot of the panel.
–
Praesideo IP address: IP address of the Praesideo system.
–
Praesideo port: Praesideo port number. The default value is 9401.
To check the availability of the Praesideo voice alarm system in the network, choose Send
ping command to send a ping request to the Praesideo IP address.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
70
en | Maintenance
15
Panel Controller
Maintenance
This chapter contains information about the following points:
15.1
–
Walktest: see Maintenance – walktest, page 73
–
Changing language display, page 70
–
Activate Outputs, page 70
–
Activate Transmission Device, page 71
–
Detector removal, page 71
–
Change device on V.24 Interface, page 71
–
History Log: see Maintenance – history log, page 77
–
Bypassing/Un-bypassing buzzer, page 72
Menu overview
Maintenance
-> Walktest
Change language
Activate outputs
Activate transmission device
Remove detector
History log
Change device at V.24
Bypass buzzer
interface
15.2
Changing language display
Notice!
The fastest way to change the language display is via a shortcut; see also Changing language
display, page 32.
There are two ways of selecting a different language display:
–
Using the menu
–
Entering a shortcut; see Changing language display, page 32.
Notice!
After the system starts up following a power cut or battery failure, the default language
defined in the FSP-5000-RPS programming software is set again.
Making a selection via the menu
1. In the start menu, select Maintenance
2.
Change language
3.
Select the language you require.
A list of the languages which can be selected is displayed.
The displays are displayed in the selected language.
15.3
Activate Outputs
1.
In the start menu, select Maintenance
2.
Activate outputs
Various element categories are displayed.
3.
Select a category or Select by number and enter the number of the element into the
search screen; see also Search Function/Element, page 29
4.
Select the required list fields. The list fields are marked.
5.
Select On to activate the selected notification appliances.
The selected signaling devices are activated.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Maintenance | en
71
6.
Select All to activate all notification appliances.
7.
To end activation of the selected elements, repeat the same steps but select Off in step
5.
Notice!
In the HVAC element category, the Auto function field is also offered. Select this function
field to assign automatic mode to a fan, for instance.
15.4
Activate Transmission Device
To activate a transmission device:
1.
In the start menu, select Maintenance
2.
Activate transmission device
A list of the elements is displayed. Refer to Working with lists, page 27 for information on
how to navigate through a list.
3.
Select the required list fields.
The list fields are marked.
4.
Select On.
The selected transmission devices are activated:
To end activation of the selected elements:
1.
In the start menu, select Maintenance
2.
Activate transmission device
3.
Select the list fields of the activated transmission devices.
4.
Select Off.
The transmission devices are no longer activated.
15.5
Detector removal
Notice!
To remove a detector, all acoustic signals and transmission devices are bypassed for 15
minutes. They are automatically un-bypassed when the 15 minutes are up.
The acoustic signals can also be manually un-bypassed before the specified time has elapsed.
To remove a detector:
1.
In the start menu, select Maintenance
2.
Remove detector
3.
Select OK to confirm the request. The following message appears:
All signaling and transmission devices will be inoperative for %d min
%d is used as a placeholder for the time that was defined in the FSP-5000-RPS
programming software, e.g. 15 minutes. The counter then counts from 15 minutes to zero
minutes. The detectors can be removed during this time.
To switch the signaling devices back on before the 15 minutes are up:
4
Select Restore manually disabled outputs.
When the 15 minutes are up, the panel emits a brief signal tone and the start menu is
displayed.
15.6
Change device on V.24 Interface
On the V.24 interface, other devices can be optionally assigned in addition to a permanently
assigned device.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
72
en | Maintenance
Panel Controller
Notice!
After the system starts up following a power cut or battery failure, the permanently set-up
device is assigned to the V.24 interface again.
To assign a different device to the V24 interface:
1.
In the start menu, select Maintenance
2.
Change device at V.24 interface
A list of devices is displayed.
3.
Select the element you require in the display.
4.
Change the device on the V.24 interface.
The device is ready for operation.
15.7
Bypassing/Un-bypassing buzzer
In order to prevent an acoustic warning tone being sent to the panel during maintenance
work, for example, the panel's internal buzzer can be permanently bypassed.
To bypass the internal buzzer, select the following from the start menu:
1.
Maintenance
2.
Bypass buzzer
The buzzer is bypassed and the text on the user interface changes to Unbypass buzzer.
To remove the bypass from the buzzer, select Unbypass buzzer in step 2.
Notice!
If you switch the internal buzzer off permanently, no acoustic signal will sound on the panel in
the event of an alarm or fault!
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Maintenance – walktest | en
73
Maintenance – walktest
16
This chapter contains information about the following points:
–
Walktest groups, page 73
–
Starting and ending walktest, page 75
–
Ending walktest for all elements, page 75
–
Displaying tested or untested elements, page 76
–
Assigning tested elements to a walktest group, page 76
A walktest is indicated by a yellow LED display on the panel.
Caution!
!
Alarm or fault messages from detectors switched to walktest are not forwarded to
transmission devices or extinguishers.
Notice!
If a signaling device is activated during a walktest, it emits a different signal tone to the one it
emits in the alarm state.
16.1
Walktest groups
The following options are available for switching elements to walktest:
–
Select individual elements from lists and/or
–
Select previously defined walktest groups consisting of at least one element.
There are 12 pre-defined walktest groups. The number of possible walktest groups is
predefined: January to December.
Example:
Detectors which are to be tested in May, can be grouped together in a group called May.
New elements can be added to a group, and elements that have already been added can be
removed.
Notice!
Even if the elements in a group (e.g. January) have been completely deleted, this group will
still be displayed in the list.
16.1.1
Adding or deleting elements
In order to add elements to a walktest group or remove elements from it:
1.
In the start menu, select Maintenance
2.
Walktest
3.
Create / Change walktest group
A list of the walktest groups is displayed.
4.
Select a walktest group, e.g. February.
You can choose from a number of options:
–
–
Delete all: Delete all elements in the selected group.
Show / Change: Delete all elements in the selected walk test group and delete
individual elements.
–
Add: Display all elements that have not yet been assigned to a walk test group, and
add individual elements.
–
Bosch Sicherheitssysteme GmbH
Cancel: Cancel the operation.
User Guide
2013.07 | 3.0 | F.01U.258.929
74
en | Maintenance – walktest
Panel Controller
Notice!
The deleted elements are assigned to the Unassigned elements group.
To change the name of the walktest group, see Change name, page 75.
Toggle function
New elements can be added and existing elements deleted in every submenu.
Add
When one of the function fields is selected, the display changes and a new function can be
performed.
+
New
Select this function field to add one or more new elements.
Only those elements which have not been assigned to any walktest group yet will be
displayed.
Various element categories are displayed.
1.
Select the category you require.
A list of elements is displayed. See also Working with lists, page 27.
2.
Select an element.
The element is marked.
3.
Select Add.
The selected element is added to the group.
Delete
Old
Select this function field to delete one or more elements.
Only elements from the selected walktest group are displayed.
1.
Select an element.
The element is marked.
2.
Select Delete.
The selected element is deleted from the group.
Example:
1. Select Show / Change.
To delete one or more element(s) from the selected group:
2.
Select one or more list fields.
The list fields are marked. Refer to Scrolling through lists, page 27 for information on how
to navigate through a list.
3.
Select Delete.
The element is deleted from the selected group. The list field is no longer displayed.
In order to add new elements:
1.
Select New.
The display changes. Various element categories containing elements which have not
been assigned to any walktest group yet are displayed.
2.
Select the element category you require.
3.
Select one or more list fields.
The list fields are marked.
4.
Select Add.
The selected element is added to the selected walktest group.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Maintenance – walktest | en
75
Change name
To change the name of the input or output group:
1.
2.
Overwrite the name; see Entering numbers and text, page 30.
Select OK.
The new name is confirmed.
16.2
Starting and ending walktest
Notice!
The information about the date and time of every walktest is stored in the history log. You can
print this information on a printer. See Maintenance – history log, page 77.
16.2.1
Starting the walktest
To select the elements for the walktest and to switch them to walktest:
1.
In the start menu, select Maintenance
2.
Walktest
3.
Start / End walktest
Various element categories are displayed.
4.
Select:
–
More... to display further categories or
–
one of the displayed categories or
–
Select by number and enter the number of the element into the search screen; see
also Search Function/Element, page 29.
Notice!
If you select the element category Loop, Logical zone, Detector or Walktest group, you will
be asked to select the type of walk test. Select Sequential walktest to check each individual
sensor (optical, chemical or thermal) of the detectors you are testing, or select Simultaneous
walktest to test combination detectors using a test device with combined trigger substances
for simultaneous testing of multiple sensors.
Example:
1.
Select Walktest group.
2.
Select Sequential walktest or Simultaneous walktest
A list of walktest groups is displayed. Refer to Scrolling through lists, page 27 for
information on how to navigate through a list.
3.
Select the list field you require.
4.
Select On.
The field is marked.
The selected walktest group is switched to walktest.
16.2.2
Ending the walktest
To end the walktest for this walktest group:
16.3
1.
Mark the selected walktest group.
2.
Select Off.
Ending walktest for all elements
To end the walktest for all walktest groups and elements:
1.
Select End from the status bar.
Various possibilities are offered on the display:
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
76
en | Maintenance – walktest
2.
Panel Controller
Select Yes in order to end the walktest for all walktest groups and elements. Select No to
cancel the operation and return to the previous display.
The walktest is ended for all walktest groups.
16.4
Displaying tested or untested elements
Notice!
You can choose to display either the untested or tested elements in the current walktest.
Select Exit from the status bar.
The following options are offered for the walktest currently being performed:
–
Select Not tested to display the elements that showed no reaction during the test or that
have not been tested.
–
16.5
Select Tested to display the elements that were tested and showed a reaction.
Assigning tested elements to a walktest group
Notice!
Only those elements in the current walktest that have been tested can be assigned to a
different walktest group.
On completion of the walktest, you can assign the tested elements to a different walktest
group (for the next walktest, for example):
1.
Select Exit from the status bar.
Various possibilities are offered on the display:
Select Assign tested elements to walktest group to assign the tested elements from the
current walk test to a walk test group for the next walk test:
A list of the walktest groups is displayed.
2.
Select a walktest group from the list. Refer to Scrolling through lists, page 27 for
information on how to navigate through a list.
Two possibilities are offered on the display:
–
Select Add to walktest group to assign the tested elements from the current walk
test to a selected walk test group.
–
Select Overwrite walktest group to replace the elements in the selected walk test
group with the tested elements from the current walk test.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
17
Maintenance – history log | en
77
Maintenance – history log
In the history log, all data about particular events or device types is stored sorted by date and
time. To display only particular data, filters can be set.
In addition to a menu overview, this chapter contains information about the following points:
17.1
–
Selecting filters, page 77
–
Setting filters, page 77
–
Change Filter, page 78
–
Combining several filters, page 78
–
Status bar functions, page 78
–
Printing out data, page 79
Selecting filters
The following filters are available:
Filter
Data, filtered by...
Without filter
All data
Show all Delete filter
Display all data with specification of event number, date,
time, element number and message type. Existing filters are
deleted.
Period
Starting date, end date and time
Event types
Message types, such as Fault
Device types
Device types, such as Detectors
Address range
Address range within a system
User commands
Selected function fields, such as Acknowledge or Reset.
Walktest
Elements switched to walktest mode
If one or more filters have been set, the Change filter field in the status bar is highlighted in a
dark color.
17.2
Setting filters
To display only particular data, a filter can be set.
Example:
To display only data that was stored in connection with a particular event, such as Fault:
1.
In the start menu, select Maintenance
2.
History log
3.
Select the Event types filter.
A list of all event types is displayed.
4.
Select a list field, e.g. Fault.
In the status bar, the Change filter field has a black background. See also Change Filter,
page 78.
5.
Select Show in history log.
A list of all fault messages is displayed. The events are sorted in ascending order by date
and time.
The fault messages are numbered chronologically. The leading number indicates the
sequence in which the fault messages were received.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
78
en | Maintenance – history log
17.3
Panel Controller
Change Filter
On each filter menu, another filter can be set using the status bar:
1.
Select Change filter from the selection bar below.
The various filters are displayed.
2.
Select one of the filters displayed.
A list with filtered data is displayed.
17.4
Combining several filters
It is possible to set several filters and to display all filtered data in a list:
To combine the Device types filter with the Message types filter:
1.
Select Maintenance from the start menu
2.
History Log
3.
Select a filter, e.g. Device types.
4.
Select Change filter in the selection list.
5.
Select the desired device types from the displayed list.
6.
Repeat steps 4 to 5 until all desired filters have been selected.
To display all filtered data of the combined filters:
7.
17.5
Select Show filter result.
Status bar functions
The following functions are offered:
To switch to the status bar on the start page, press the "double
arrow" key in the status bar or on the membrane keypad.
Change filter
If the field has a black background, a filter has been set. Select
this field to set a different filter.
Go to no.
Enter the number of a specific event.
The event with the selected number is displayed at the start of
the list.
Go to day
Enter a date.
All events with the selected date are displayed in the list.
Print
Print the complete displayed list or only a part of it.
Exit
End the entry and switch to the menu overview for the
Maintenance menu.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
17.6
Maintenance – history log | en
79
Printing out data
Either the complete list or a specific part of it can be printed out.
To print out data that is displayed on a list:
1.
Select Print from the status bar.
Two possibilities are offered:
–
Entire list: The complete list is selected.
–
Define range: Specify a particular area within the list.
To print the list, continue with step 6.
The following two possibilities are available to specify the area of the list to be printed
out:
–
Limit the number of events, counted from the newest event.
–
Specifying a particular area via the entry of the event numbers.
2.
Select Define range.
3.
Activate the checkbox in front of one of the two options:
Two possibilities are offered on the display.
–
Number of events to be printed starting from latest event:
For the printout, enter a particular number of events, counted from the most recent
event.
–
Event numbers to be printed:
To print out a particular range, specify by entering event numbers.
A checkmark is placed in the selection field.
4.
Enter the numbers you require.
To enter a number, see Entering numbers and text, page 30.
5.
Select OK to confirm the entry.
A list of the printers that can be selected is displayed.
6.
Select a printer.
7.
Select Print.
The list is printed.
Event numbers
To display the event numbers again:
1.
Select Show event numbers.
2.
To exit the display, press the "Back" key.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
80
en | Day and night mode
Panel Controller
Day and night mode
18
This chapter contains information about the following points:
–
Switching between day and night mode
–
Changing the time for resetting to night mode
The manner in which an incoming alarm is handled depends on whether the system is in day
or night mode; see Fire alarm, page 47.
Caution!
!
Night mode is the highest security level as every incoming alarm is forwarded to external
stations.
Notice!
Depending on the security level in question, not all detectors can be switched to day mode.
The following symbols on the status bar or standby display show which mode the panel is
switched to. In the case of networked panels, "Day Mode" is displayed until all networked
panels have been switched to night mode. While one panel is still in day mode, the day mode
icon is also displayed on all other panels.
Night mode
Day mode
Notice!
Please note that following a transmission fault it may be necessary to synchronize the day/
night mode of the other panels manually in order for the current mode to be displayed
correctly.
18.1
Switching between day and night mode
Notice!
Depending on the programming, the panel automatically switches from day to night mode at
the preset time. It is only possible to switch to day mode manually.
There are two ways to switch between day and night mode:
–
Switching over via the menu
–
Switching via the status bar
Switching over via the menu
Depending on the mode to which the panel is switched, Switch to day mode or Switch to
night mode is displayed in the start menu.
1.
The panel is in night mode: Select Switch to day mode to switch to day mode:
2.
Confirm your selection with Switch to day mode.
The panel is switched to day mode.
To cancel the operation, select Cancel.
If the panel is in day mode, select Switch to night mode to switch to night mode.
Switching via the status bar
The panel is in night mode. To switch it to day mode:
4
2013.07 | 3.0 | F.01U.258.929
Press
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Day and night mode | en
4
81
Select Switch to day mode to confirm the request or Cancel to cancel the operation.
The panel is in day mode. To switch it to night mode:
18.2
4
Press
4
Select Switch to night mode to confirm the selection or Cancel to cancel the operation.
Showing details
It is possible both in day and night mode to display a list of all logical zones on the panel that
are currently switched to day mode.
To display a list of all detector groups in day mode
1.
In the start menu, select Switch to day mode or Switch to night mode, depending on
which mode the panel is currently in, or select the "day mode" or "night mode" icon on
the status bar.
2.
Select Show details.
A list of all logical zones that are switched to day mode is displayed.
Changing the time for resetting to night mode
18.3
Caution!
!
After the system starts up following a power cut or battery failure, the default set back time
in FSP-5000-RPS is reset.
Notice!
Depending on the configuration, the set back time can be changed. It is only possible to make
a change for the current day. It is only possible to make a change if a specified time has
already been set for the current day in the programming software.
The set back time can be changed in day or night mode.
To change the time for resetting in night mode:
1.
On the status bar, select
or
In the start menu, select Switch to day mode.
2.
Select Change time.
3.
Enter the numbers you require.
Refer to Entering numbers and text, page 30 for information on how to enter numbers.
4.
Select OK to confirm the entry or Cancel to cancel the operation.
The entries are confirmed.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
82
en | Day and night mode
Panel Controller
To change the set back time in day mode to night mode:
1.
On the status bar, select
or
In the start menu, select Switch to night mode.
2.
Select Change time.
3.
Enter the numbers you require.
Refer to Entering numbers and text, page 30 for information on how to enter numbers.
4.
2013.07 | 3.0 | F.01U.258.929
Select OK to confirm the entry or Cancel to cancel the operation.
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
19
Configuration | en
83
Configuration
This chapter contains information about the following points:
–
19.1
Input / Output Group Set Up, page 83
–
Group setting, page 85
–
Detector sensitivity, page 85
–
Operator, page 86
–
Rename elements, page 87
–
Network, page 87
–
Overview, page 87
Menu overview
Configuration
-> Set input / output
Set groups
groups
Detector sensitivity
Operator
Rename elements
Overview
Network
19.2
Input / Output Group Set Up
Input and output groups can be created using the FSP-5000-RPS programming software:
Input groups consist of several detectors and/or logical zones;
Output groups consist of signaling devices and transmission devices.
Specify which input group activates which output group by using the programming software.
The following can be carried out on the panel controller:
19.2.1
–
Elements can be added to, or removed from input or output groups.
–
Input or output groups can be renamed.
Adding or deleting elements
Input group
In order to add elements to an input group or remove elements from it:
1.
In the start menu, select Configuration
2.
Set input / output groups
3.
Input group
4.
Select a list, e.g. By description.
Two different lists are displayed. See Working with lists, page 27.
A list of the various input groups is displayed. Refer to Scrolling through lists, page 27 for
information on how to navigate through a list.
5.
Select the list field you require.
The list field is marked.
You can select various options:
–
Delete all: Delete all elements in the selected input group.
–
Show / Change: Display all elements in the selected input group and delete
individual elements.
–
Add: Display all elements that have not yet been assigned to an input group, and add
individual elements.
–
Cancel: Cancel the operation.
To change the name of the input group, see Change name, page 85.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
84
en | Configuration
Panel Controller
Output group
To display the elements in an output group and to delete or add elements, repeat the steps
shown in the example for the input group (Adding or removing, page 85) but select Output
group in step 3.
Toggle function
New elements can be added and existing elements deleted in every submenu.
When one of the function fields is selected, the display changes and a new function can be
performed.
Add
+
New
Select this function field to add one or more new elements.
Only those elements that have not yet been assigned to an input group will be displayed.
Various element categories are displayed.
1.
Select the category you require.
A list of elements is displayed. See also Working with lists, page 27.
2.
Select an element.
The element is marked.
3.
Select Add.
The selected element is added to the group.
Delete
Old
Select this function field to delete one or more elements.
Only elements from the selected input group are displayed.
1.
Select an element.
The element is marked.
2.
Select Delete.
The selected element is deleted from the group.
Example:
1. Select Show / Change.
To delete one or more element(s) from the selected group:
2.
Select one or more list fields.
The list fields are marked. Refer to Scrolling through lists, page 27 for information on how
to navigate through a list.
3.
Select Delete.
The element is deleted from the selected group. The list field is no longer displayed.
In order to add new elements:
1.
Select New.
The display changes. Various element categories containing elements which have not
been assigned to any walktest group yet are displayed.
2.
Select the element category you require.
3.
Select one or more list fields.
The list fields are marked.
4.
Select Add.
The selected element is added to the selected walktest group.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Configuration | en
85
Change name
19.2.2
To change the name of the input or output group:
1.
2.
Overwrite the name; see Entering numbers and text, page 30.
Select OK.
The new name is confirmed.
Group setting
19.3
Bypass, isolate and walktest groups can be created using the FSP-5000-RPS programming
software.
Each group can consist of one or more element(s).
You can use the panel controller to carry out the following:
19.3.1
–
Adding elements to or removing elements from bypass, isolate and walktest groups.
–
Renaming bypass, isolate and walktest groups.
Adding or removing
Bypass Group
In order to add elements to a bypass group or remove elements from it:
1.
In the start menu, select Configuration
2.
Set groups
3.
Bypass group
Two different sorting criteria are displayed. See also Working with lists, page 27.
4.
Select a list type, e.g. By number.
A list of all bypass groups is displayed. The number in brackets specifies the number of
elements in the bypass group in question. Refer to Scrolling through lists, page 27 for
information on how to scroll forward and backward through the list.
5.
Select the list field you require.
You can choose between various options. To add elements to a group or remove elements
from it, see Adding or removing, page 85.
Isolate Group
To display the elements in a block group and to delete or add elements, repeat the steps, but
select Block Group in step 3.
Walktest Group
To display the elements in a walktest group and to delete or add elements, see Walktest
groups, page 73.
19.4
Detector sensitivity
Caution!
!
Detector sensitivity is automatically reset to the default setting
When the entire panel or the individual detector/logical zone is reset
When the detector is replaced
Two different sensitivities can be assigned to detectors and logical zones in the FSP-5000-RPS
programming software — a default setting and an alternative setting.
It is possible to switch between the default and alternative setting on the panel controller.
To change the setting:
1.
In the start menu, select Configuration
2.
Detector sensitivity
Various lists are offered. Refer to Scrolling through lists, page 27 for information on how to
scroll forward and backward through a list.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
86
en | Configuration
3.
Panel Controller
Select one of the detector or logical zone lists that are offered.
A list of elements is displayed. Refer to Scrolling through lists, page 27 for information on
how to scroll forward and backward through the list.
Depending on the list you have selected, enter the number or the name of the element
into the search screen, Search Function/Element, page 29.
4.
Select the list field you require, e.g. a logical zone in this case.
Two settings are displayed: There is a checkmark in the selection field in front of the
active setting.
5.
Select the selection field of the detector sensitivity you require.
A checkmark is set in this field.
6.
Select OK to confirm the selection or Cancel to cancel the operation.
The selected detector sensitivity is confirmed for the detector.
19.5
Operator
Depending on whether the same password is used per access level, or whether each user has
a different password, one of the following two options is offered:
If the same password is used per access level:
–
Change universal password: The same password can be configured for each access level
in the FSP-5000-RPS programming software. This means that all operators with access
authorization for the second level receive the same password, for example. The password
for access levels two to four can be changed.
If each user uses a different password:
–
Change operator data: Change the password for an operator.
–
Set default password: Reset a user password to the following number sequence: 000000.
Notice!
The password must contain at least one character.
19.5.1
Change password
1.
In the start menu, select Configuration
2.
Operator
3.
Change operator data
A list of all operators is displayed. Refer to Scrolling through lists, page 27 for information
on how to scroll forward and backward through a list.
4.
Select the list field you require.
5.
Enter a new password. Repeat the new password in the bottom field again.
On the display, each digit of the password is indicated with an asterisk so that nobody
else can see the password. Refer to Entering numbers and text, page 30 for information on
how to enter figures or text.
6.
Select OK to confirm the entry or Cancel to cancel the operation.
The entry is confirmed.
19.5.2
Change universal password
1.
In the start menu, select Configuration
2.
Operator
3.
Change universal password
4.
Depending on the access level for which the password is to be changed, select the list
field you require.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Configuration | en
5.
87
Enter a new password and repeat the entry in the bottom field again.
On the display, each digit of the password is indicated with an asterisk so that nobody
else can see the password.
6.
Select OK to confirm the entry or [MISSINGDISPLAYTEXT: Cancel] to cancel the
operation.
The entry is confirmed.
19.5.3
Set Default Password
1.
In the start menu, select Configuration
2.
Operator
3.
Set default password
A list of all operators is displayed. Refer to Scrolling through lists, page 27 for information
on how to scroll forward and backward through a list.
4.
Select the list field you require.
The list field is marked.
5.
Select Reset.
The operator’s password is reset to his/her previous password.
19.6
Rename elements
To change the name of an element:
1.
In the start menu, select Configuration
2.
Rename elements
A list of all elements is displayed. Refer to Scrolling through lists, page 27 for information
on how to scroll forward and backward through a list.
3.
Select the list field you require.
An entry screen is displayed.
4.
Enter a new name. Refer to Entering numbers and text, page 30 for information on how to
5.
Select OK to confirm the entry or Cancel to cancel the operation.
enter text.
The event with the new name is displayed on the list.
19.7
Network
You can modify and activate the network settings (IP settings, Ethernet redundancy) of panels
and remote operating panels that are networked via an Ethernet connection under
Configuration - Network. Further information can be found in Networking via Ethernet, page
37.
19.8
Overview
To display important information on the valid configuration of the system:
1.
In the start menu, select Configuration
2.
Overview
The following information is displayed:
–
Configuration and additional information on this
–
Date
–
Configuration version (Config. version)
–
Number
–
Name
–
IP address
–
Scope
–
Country
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
88
en | Configuration
2013.07 | 3.0 | F.01U.258.929
Panel Controller
–
Time zone
–
Menu name
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
20
Further functions | en
89
Further functions
This chapter contains information about the following points:
–
20.1
Change Date / Time, page 89
–
Master password, page 89
–
Remote Access, page 90
–
Change password, page 90
–
Performing a fire drill, page 91
–
Alarm Counters, page 91
Menu overview
Further functions
20.2
-> Change date / time
Master password
Remote access
Change password
Drill
Alarm counters
Change Date / Time
To change the date and time:
1.
In the start menu, select Further functions
2.
Change date / time
3.
Touch the field you require and enter a new value.
Refer to Entering numbers and text, page 30 for information on how to enter figures or
text.
4.
Select OK to confirm the entry or Cancel to cancel the operation.
The new values for date and time are accepted into the system.
20.3
Master password
Notice!
With the master password, all functions can be operated and passwords and names can be
changed.
One of the following two options is offered:
–
Entering a master password that is valid indefinitely. This password cannot be changed
and is available from the relevant Bosch branch on request.
–
Entering a master password that is valid for a specified period of time.
This password is only valid for 24 hours. The panel controller can issue a number on
request. This number must be forwarded to the Support department. The Support
department can then issue a 24-hour password; see Enter the 24-hour master password,
page 90.
Notice!
The Support department can be reached on the following number: +49 (0)89-62 90 18 88.
Business hours:
Monday to Thursday from 8 am to 5 pm
Friday from 8 am to 4 pm
After the password has been entered, various options are offered; see Operator, page 86.
20.3.1
Enter the master password that is valid indefinitely
1.
In the start menu, select Further functions
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
90
en | Further functions
Panel Controller
2.
Master password
3.
Enter the master password. Refer to Entering numbers and text, page 30 for information
on how to enter figures or text.
4.
Select OK to confirm the entry or Cancel to cancel the operation.
The master password is accepted and the operator is logged in.
The user passwords can now be changed:
Select Change password.
Additional options may be offered. See also Operator, page 86.
20.3.2
Enter the 24-hour master password
The following procedure must be followed in order to obtain a 24-hour master password:
The panel controller generates a number on request. The operator forwards this number to
the relevant NSO by telephone. The NSO gives the user a password which is only valid for 24
hours.
1.
In the start menu, select Further functions
2.
Master password
3.
Create number
4.
Request password
A number is displayed.
5.
Give the number issued by the system to the Support department.
6.
Once you have received the 24-hour password from the Support department, select Enter
password!.
7.
Enter the password.
The 24-hour master password is accepted and the user is logged on.
Change password
To change passwords, select Change password.
Additional options may be offered. See also Operator, page 86.
20.4
Remote Access
Notice!
If another menu is called up while the connection to the Remote Access is still active, the
following text is displayed RAM active. To blank out the text, touch the screen. The text reappears every 30 seconds for as long as the Teleservice connection remains active.
To create a connection to the teleservice:
1.
In the start menu, select Further functions
2.
Remote access
3.
Enable call
The Remote Access can now call the system. Afterwards, the connection is disconnected.
4.
Select Call back to restore the connection with the Remote Access center.
Active is displayed when a connection has been made to the Teleservice.
To disconnect the connection, select Stop RAM.
20.5
Change password
Notice!
If all operators with the same access authorization have the same password, this function
cannot be used.
1.
2013.07 | 3.0 | F.01U.258.929
In the start menu, select Further functions
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Further functions | en
2.
91
Change password
A list of all operators is displayed.
Refer to Scrolling through lists, page 27 for information on how to navigate through a list.
3.
Select the list field you require.
4.
Enter the password.
On the display, each digit of the password is indicated with an asterisk so that nobody
else can see the password.
20.6
5.
Enter a new password and repeat the entry in the bottom field again.
6.
Select OK to confirm the entry or Cancel to cancel the operation.
Performing a fire drill
During a drill, all signaling devices are activated.
Caution!
!
If a genuine alarm is reported during a fire drill, the fire drill is abandoned. The fire drill can
only be restarted when the alarm is ended.
To start a drill:
1.
In the start menu, select Further functions
2.
Drill
3.
Confirm Start drill with OK
The drill is started.
To end the drill, select Stop drill.
During the fire drill, fire alarms, fault messages and supervisory alarms are displayed.
To switch between the fire drill display and the message display in question, select Return to
message screen or Return to drill screen on the status bar.
If an alarm or a fault/supervisory alarm is sounded during a fire drill, the panel controller
reacts as described in the table below:
Fire alarm
Fault/ supervisory alarm
Yes
No
Yes
No
Display switches to
Alarm indication
Fault indication
Fire drill after event ends
Must be restarted
Continue
The drill signaling devices are
switched off.
The drill is automatically
terminated.
manually
A new function cannot be selected until the fault/supervisory alarm and/or the fire drill have
been completed.
20.7
Alarm Counters
Show Lifetime Event Counters
During the lifetime of the panel, the following alarm messages are counted:
–
External alarm: all fire messages
–
Internal alarm: all alarm messages that the panel receives in day mode
–
Walktest alarm: all messages from detectors switched to walktest
To display the number of alarm messages which have been counted so far:
1.
In the start menu, select Further functions
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
92
en | Further functions
2.
Panel Controller
Alarm counters
The figure after the message type shows the number of messages counted so far.
Reset counters
You can reset the alarm counter for individual alarm types to 0.
To reset alarm counters
1.
In the start menu, select Further functions
2.
Alarm counters
3.
Mark the alarm counter you require (e.g. external alarm)
4.
Select Reset
5.
Confirm the message "Attention: Counter will be reset" with OK to reset the alarm
counter to 0 or select Cancel to cancel the operation.
Notice!
In order to reset alarm counters, you need authorization level 4.
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
21
Reset | en
93
Reset
This chapter contains information on how to reset elements.
During resetting, the selected elements are reset to the initial state.
–
Event type: Display a list of all message types. The message types can be reset for the
entire Scope.
–
Scope: Depending on the Scope set in FSP-5000-RPS, the current panel, all panels in a
group or all the panels in the entire network are reset.
–
Logical zone
–
Detector
–
This panel: All elements of the panel that are not in standby mode are reset
Notice!
If the Scope refers to one panel (local), the list fields This panel and Scope have the same
function.
21.1
Menu overview
Reset
-> Event type
Scope
Logical zone
Detector
This panel
21.2
Resetting elements
To reset a detector or logical zone, for example:
1.
In the start menu, select Reset
2.
Select the element you require.
3.
Select the detector or zone. Refer to Scrolling through lists, page 27 for information on
how to navigate through a list.
4.
Select the required list fields.
The list fields are marked.
A list of the detectors or zones is displayed.
5.
Select Reset.
The selected elements are reset.
Notice!
As long as the elements are still in the process of resetting, no other entries can be made.
If a list field is marked with an R, the process of resetting is not yet complete for this element:
TEXT
R
If an element cannot be reset, it will continue to be displayed in the list.
After the elements have been reset, the standby display is displayed.
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
94
en | Search Function/Element
22
Panel Controller
Search Function/Element
This chapter contains information about the following points:
22.1
–
Searching for function and device description, page 94
–
Search element, page 94
Menu overview
Search function /
-> Search function
element
Go to element
22.2
Searching for function and device description
To search for a function or a device:
1.
In the start menu, select Search function / element
2.
Search function
A list of all functions and device descriptions is displayed.
Refer to Scrolling through lists, page 27 for information on how to navigate through a list.
3.
Select the list field you require.
The submenu of the selected function or device description is displayed.
22.3
Search element
To search for an element which is connected to the system:
1.
In the start menu, select Search function / element
2.
Go to element
Three different lists are offered. See also Working with lists, page 27.
3.
Select a list, e.g. By description.
A list of the detectors is displayed. Refer to Scrolling through lists, page 27 for information
on how to navigate through a list.
4.
Select the list field you require.
Different selection fields may be offered for the selected element (e.g. OK, Bypass). What
is displayed depends on:
2013.07 | 3.0 | F.01U.258.929
–
the message types (e.g. fault, alarm etc.) that can be assigned to this element.
–
the mode (e.g. bypassed, reset etc.) that the selected element is in.
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Index | en
95
Index
Symbols
C
"Double arrow" function key, 20
Calibration, 64
"Enter" function key, 20
Calling up the start menu, 8, 12, 26
"Key" function key, 20
CAN ID, 65
"Left arrow" function key, 20
CAN-Bus, 65
"Right arrow" function key, 20
Change Date / Time, 89
A
Change operator data, 86
Access authorization, 25, 26
Activate Outputs, 70
Activate Transmission Device, 71
Adjust Touch Position, 64
Alarm Counters, 91
Alarm delay, 41
Alarm message, 43
Alarm message, information, 44
Alarm message, sequence, 44
Alarm verification, 42, 48
Alarm, displaying further information, 46
Change password, 86, 90
Change universal password, 86
Changing entry, 31
Changing language display, 9, 32, 70
Changing time for resetting to night mode, 81
Checking access authorization, 26
Condition Monitoring
State of Condition Monitoring, 68
Configuration version, 87
Consistency check, 66
Country, 87
Alarm, individual detector, 45
D
Alarm, logical zones, 43
Day mode, 43, 80
Alarm, message number, 45
Day/night mode, showing details, 81
Assigning tested elements to a walktest group, 76
Day/night mode, switching, 80
B
Default language, 70
Build number, 65
by description, 27
by number, 27
by Number (no Description shown), 27
Bypass group, adding elements, 85
Bypass group, removing elements, 85
Bypassing detectors, 50
Bypassing elements, 57
Bypassing/Un-bypassing buzzer, 59, 72
De-isolating elements, 60
Deleting numbers, 32
Description, search by, 30
Detector removal, 71
Detector sensitivity, 85
Diagnostics, 62
Diagnostics, address cards, 63
Diagnostics, All info for one element, 62
Diagnostics, element details, 62
Diagnostics, Info for all elements, 62
Diagnostics, Info for element group, 62
Diagnostics, modules, 63
Display elements, 20
Display Test, 64
Display touch test, 64
Displaying bypassed element groups, 58
Dual homing, 38
Dual-detector dependency, 42
Dual-zone dependency, 42
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
96
en | Index
Panel Controller
E
I
Ending the walktest, 75
Icons, networking, 34
Enter Password, 25
Input / Output Group Set Up, 83
Enter the 24-hour master password, 90
Input group, adding elements, 83
Enter the master password that is valid indefinitely,
Input group, deleting elements, 83
89
Input/output group, changing name, 85
Entering numbers, 31
Interfaces, 66
Entering text, 31
Intermediate alarm storage, 42
Ethernet, 37
IP Address, 87
Ethernet configuration, 37
IP settings, 37
Ethernet ports, 66
Isolate Group, 85
Ethernet redundancy, 38, 67
isolated elements, displaying list, 60
F
Isolating an element, 55
Fault message, 52
Isolating connection, 35
Fault message, acknowledging, 52
K
Fault message, further information, 54
Key switch, 20
Fault message, information about element group, 53
Fault message, information about elements, 54
Fault message, latest message, 53
Fault message, resetting, 55
Fault message, sequence, 53
Fault, element group, 52
Fault, signals, 55
Finished Good Material Number, 65
Fire, 41
Fire alarm, acknowledging message, 47
Fire alarm, signaling, 47
Foil Test, 64
Function keys, 19
G
Ground fault, 23
Group setting, 85
H
Heat, 41
History log, changing filter, 78
History log, combining filters, 78
History log, event numbers, 79
History log, filter, 77
History log, printing out data, 79
History log, setting filter, 77
History log, status bar functions, 78
L
LED display, 20
LED Test, 64
LED Test on modules, 65
List fields, states, 28
List, assigning mode, 29
List, select, 29
Lists, 27
Lists, scrolling, 27, 28
Logging in, 25
Logging out, 26
Logical addressing, 32
M
MAC Address, 65
Master password, 89
N
Network, 66
Network addressing, 34
Networking, establish remote connection, 35
Networking, terminating remote connection, 35
Night mode, 42, 80
Node number, 66
Number, search by, 30
O
Operating elements, 19
Operator, 86
Optical/acoustic signals, 43
Output group, adding elements, 84
Output group, deleting elements, 84
Overview, 87
2013.07 | 3.0 | F.01U.258.929
User Guide
Bosch Sicherheitssysteme GmbH
Panel Controller
Index | en
P
S
Panel Passport, 65
Scope, 87
Password, default setting, 25
Search Function/Element, 29
PCB Material Number, 65
Search mask, 29
PCBA Revision Level, 65
Searching, device description, 94
Performing a fire drill, 91
Searching, element, 94
Physical addressing, 32
Searching, function, 94
Ping command, 67
Selecting the menu, 26
Production Date, 65
Serial Interface, 65
Q
Set Default Password, 86, 87
Quick entry of text and numbers, 31
R
Show Lifetime Event Counters, 91
Smoke, 41
Standby, 8
Remote keypad, 40
Standby display, 23
Remote keypad, display, 40
Standby screen, 8
Remote keypad, operation, 40
Starting the walktest, 75
Rename elements, 87
Starting time to investigate, 49
Reset counters, 92
Status bar, 23
Resetting alarm message, 50
Steps, 8
Resetting external signaling devices, 48
Supervisory alarm, 41
Resetting, detectors, 93
Support information, support service, address, 24
Resetting, elements, 93
SW Version, 65
Resetting, message type, 93
Switching external signaling devices off, 48
Resetting, scope, 93
Switching external signaling devices on, 48
Resetting, this panel, 93
Switching off internal buzzer, 47
Resetting, zone, 93
Switching status bars, 32
Restricted connection, 35
T
Routing table, 65
RSTP settings, 38
97
Time to acknowledge, 49
Time to investigate, 49
Time zone, 88
Touch screen, 10, 22
Triggering alarm manually, 49
Triggering fire verification, 48
Types of alarm, 41
U
Un-bypassing bypassed element groups, 58
Un-bypassing elements, 57
V
V.24 interface, 71
Voice Alarm System
Plena, 68
Praesideo, 68
Bosch Sicherheitssysteme GmbH
User Guide
2013.07 | 3.0 | F.01U.258.929
Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
www.boschsecurity.com
© Bosch Sicherheitssysteme GmbH, 2013