Home Theater System
with 5 Disc DVD
Changer and HDMI
HT-HDP40
SAMSUNG ELECTRONICS AMERICA, INC.
SERVICE DIVISION
400 Valley Road, Suite 201
Mount Arlington, NJ 07856
1-800-SAMSUNG (1-800-726-7864)
www.samsung.com
AH68-01663R
Instruction Manual
COMPACT
DIGITAL AUDIO
Safety Warnings
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE REAR COVER.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
ENG
PREPARATION
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LASER CLASE 1
Precautions
Note to CATV system installer :
This reminder is provided to call the CATV system
installer’s attention to Section 820~40 of the NEC
which provides guidelines for proper grounding and,
in particular, specifies that the cable ground shall be
connected to the grounding system of the building,
as close to the point of cable entry as practical
CLASS 1 LASER PRODUCT
Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install your
player horizontally, on a suitable base (furniture), with enough space around it for ventilation (3~4inches). Make sure the ventilation
slots are not covered. Do not stack anything on top of the player. Do not place the player on amplifiers or other equipment which may
become hot. Before moving the player, ensure the disc tray is empty. This player is designed for continuous use. Switching off the Home
Theater to the stand-by mode does not disconnect the electrical supply. In order to disconnect the player completely from the power
supply, remove the main plug from the wall outlet, especially when left unused for a long period of time.
This Compact Disc player is classified as a CLASS 1
LASER product.
Use of controls, adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
CAUTION-INVISIBLE LASER RADIATION WHEN OPEN
AND INTERLOCKS DEFEATED, AVOID
EXPOSURE TO BEAM.
During thunderstorms, disconnect AC main plug from the
wall outlet.
Voltage peaks due to lightning could damage the unit.
Do not expose the unit to direct sunlight or other heat
sources.
This could lead to overheating and malfunction of the unit.
This symbol indicates that dangerous voltage which can cause electric shock is present inside
this unit.
This symbol alerts you to important operating and maintenance instructions accompanying
the unit.
Phones
WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
1
Protect the player from moisture(i.e. vases) , and excess heat
(e.g.fireplace) or equipment creating strong magnetic or electric fields
(i.e.speakers...). Disconnect the power cable from the AC supply if the
player malfunctions. Your player is not intended for industrial use.
Use of this product is for personal use only.
Condensation may occur if your player or disc has been stored in cold
temperatures.
If transporting the player during the winter, wait approximately 2 hours
until the unit has reached room temperature before using.
The batteries used with this product contain chemicals
that are harmful to the environment.
Do not dispose of batteries in the general household
trash.
2
Safety Instructions
RETAIN INSTRUCTIONS
The safety and operating instructions should be
retained for future reference.
HEED WARNINGS
All warnings on the appliance and in the operating
instructions should be adhered to.
FOLLOW INSTRUCTIONS
All operating and use instructions should be
followed.
WATER AND MOISTURE
Do not use this video product near waterfor example, near a bathtub, wash bowl,
kitchen sink, or laundry tub, in a wet basement,
or near a swimming pool, and the like.
OVERLOADING
Do not overload wall outlets and extension cords as
this can result in the risk of fire
or electric shock.
VENTILATION
Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the
video product and to protect it from overheating
these openings must not be blocked or covered.
The openings should never be blocked
by placing the video product on a bed, sofa, rug, or
other similar surface. This video product
should never be placed near or over a radiator or
heat register.
This video product should not be placed
in a built-in installation such as a bookcase
or rack unless proper ventilation is provided
or the manufacturer's instructions have been followed.
POWER CORD PROTECTION
Power-supply cords should be routed so that
they are not likely to be walked on or pinched
by items placed upon or against them paying
particular attention to cords at plugs,
convenience receptacles, and the point where
they exit from the appliance.
3
CLEANING
Unplug this video product from the wall outlet
before cleaning. Do not use liquid cleaners
or aerosol cleaners. Use a damp cloth for cleaning.
LIGHTNING
For added protection of this video product
receiver during a lightning storm, or when
it is left unattended and unused for long
periods of time, unplug it from the wall outlet
and disconnect the antenna or cable system.
This will prevent damage to the video product
due to lightning and power-line surges.
OBJECT AND LIQUID ENTRY
Never push objects of any kind into this
product through openings as they may touch
dangerous voltage points or short-out parts
that could result in a fire or electric shock.
Never spill liquid of any kind on the video
product.
ACCESSORIES
Do not place this video product on an unstable cart,
stand, tripod, bracket, or table.
The video product may fall, causing serious injury to
a child or adult, and serious damage
to the appliance.
Use only with a cart, stand, tripod, bracket,
or table recommended by the manufacturer,
or sold with the video product. Any mounting
of the appliance should follow the manufacturer's
instructions and should use a mounting accessory
recommended by the manufacturer.
CART
An appliance and cart combination should be moved
with care. Quick stops, excessive force, and uneven
surfaces may cause the appliance and cart combination to overturn.
POWER SOURCES
This video product should be operated only from the
type of power source indicated
on the marking label. If you are not sure
of the type of supply to your home, consult your
appliance dealer or local power company.
For video products intended to be operated from battery power, or other sources, refer
to the operating instructions.
POWER LINES
An outside antenna system should not be located in
the vicinity of overhead power lines or other electric
light or power circuits,
or where it can fall into such power lines
or circuits. When installing an outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with
them might be fatal.
POLARIZATION
This video product is equipped with a polarized
alternating current line plug (a plug having one
blade wider than the other.) This plug will fit into the
power outlet only one way.
This is a safety feature. If you are unable
to insert the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
OUTDOOR ANTENNA GROUNDING
•If an outside antenna is connected to the
antenna terminal, be sure the antenna system
is grounded so as to provide some protection
against voltage surges and built-up static
charges.
•In the U.S.A section 810 of the National
Electrical Code, ANSI/NFPA No. 70-1984,
provides information with respect to proper
grounding of the mast and supporting
structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit,
connection to grounding electrodes, and
requirements for the grounding electrode.
See the figure below.
ATTACHMENTS
Do not use attachments not recommended
by the video product manufacturer as they may
cause hazards.
SERVICING
•Do not attempt to service this product yourself
as opening or removing covers may expose
you to dangerous voltage or other hazards.
•Refer all servicing to qualified service personnel.
REPLACEMENT PARTS
When replacement parts are required, be sure the
service technician has used replacement parts specified by the manufacturer or having the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA
DISCHARGE UNIT
(NEC SECTION. 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
SAFETY CHECK
Upon completion of any service or repairs
to this video product, ask the service technician to
perform safety checks to determine that the video
product is in proper operating condition.
DAMAGE REQUIRING SERVICE
Unplug this video product from the wall outlet and
refer servicing to qualified service personnel under
the following conditions.
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have
fallen into the video product.
c. If the video product has been exposed to rain
or water
d. If the video product does not operate normally
by following the operating instructions.
Adjust only those controls that are covered
by the operating instructions as an improper
adjustment of other controls may result
in damage and will often require extensive
work by a qualified technician to restore
the video product to its normal operation.
e. If the video product has been dropped
or the cabinet has been damaged.
f. When the video product exhibits a distinct
change in performance - this indicates
a need for service.
HEAT
This video unit should be situated away from heat
sources such as radiators, stoves, or other products
(including amplifiers) that produce heat.
4
PREPARATION
READ INSTRUCTIONS
All the safety and operating instructions should be
read before the appliance is operated.
ENG
Features
Contents
ENG
PREPARATION
Multi-Disc Playback & FM Tuner
DVD-Audio compatible
Experience the super high-quality audio performance of DVD-Audio.
The on-board 24-bit/192kHz DAC enables this player to deliver exceptional sound quality in
terms of dynamic range, low-level resolution and high-frequency detail.
Dolby Pro Logic II
Dolby Pro Logic II is a new form of multi-channel audio signal decoding technology
that improves upon existing Dolby Pro Logic.
DTS (Digital Theater Systems)
DTS is an audio compression format developed by Digital Theater Systems Inc.
It delivers full-frequency 5.1 channel sound.
TV Screen Saver Function
The HT-HDP40 automatically brightens and darkens your TV screen
after 3 minutes in the stop mode.
The HT-HDP40 automatically switches itself into the power saving mode
after 20 minutes in the screen saver mode.
Power Saving Function
The HT-HDP40 automatically shuts itself off after 20 minutes in the stop mode.
Customized TV Screen Display
The HT-HDP40 allows you to select your favorite image during JPEG and DVD playback
and set it as your background wallpaper.
Samsung AV Device Operation using Anynet
Using Anynet you can conveniently operate your Samsung DVD and AV devices with
your Samsung TV remote control.
PREPARATION
The HT-HDP40 combines the convenience of multi-disc playback capability, including
DVD-AUDIO, DVD-VIDEO, CD, MP3-CD, CD-R/RW, and DVD-R/RW, with a
sophisticated AM/FM tuner, all in a single player.
Safety Warnings..................................................................................................................................................................1
Precautions .........................................................................................................................................................................2
Safety Instructions ..............................................................................................................................................................3
Features..............................................................................................................................................................................5
Notes on Discs....................................................................................................................................................................7
Description ..........................................................................................................................................................................9
CONNECTIONS
Connecting the Speakers ...................................................................................................................................................13
Connecting the Video Out to TV .........................................................................................................................................15
Connecting the HDMI IN/OUT ............................................................................................................................................16
HDMI Function....................................................................................................................................................................17
Connecting External Components......................................................................................................................................19
How to Connect to Anynet..................................................................................................................................................21
Connecting the FM and AM Antennas ...............................................................................................................................22
Before Using Your Home Theater .......................................................................................................................................23
OPERATION
Disc Playback .....................................................................................................................................................................25
Selecting a Disc in the Disc changer..................................................................................................................................26
MP3-CD Playback...............................................................................................................................................................27
Displaying Disc Information ................................................................................................................................................28
JPEG File Playback ............................................................................................................................................................29
DivX Playback.....................................................................................................................................................................31
Checking the Remaining Time............................................................................................................................................33
Fast/Slow Playback.............................................................................................................................................................34
Skipping Scenes/Songs......................................................................................................................................................34
Repeat Playback.................................................................................................................................................................35
A-B Repeat Playback..........................................................................................................................................................36
Step Function......................................................................................................................................................................37
Angle Function....................................................................................................................................................................37
Zoom (Screen Enlarge) Function .......................................................................................................................................38
EZ VIEW Function ..............................................................................................................................................................38
Bonus Group / Navigating Pages .......................................................................................................................................39
Selecting Audio/Subtitle Language.....................................................................................................................................40
Moving Directly to a Scene/Song .......................................................................................................................................41
Using Disc Menu.................................................................................................................................................................42
Using the Title Menu...........................................................................................................................................................42
SETUP
Setting the Language..........................................................................................................................................................43
Setting TV Screen type.......................................................................................................................................................45
Setting Parental Controls (Rating Level).............................................................................................................................47
Setting the Password ..........................................................................................................................................................48
Setting the Wallpaper..........................................................................................................................................................49
DVD Audio Disc Playback Mode.........................................................................................................................................51
Setting the Speaker Mode ..................................................................................................................................................52
Setting the Delay Time........................................................................................................................................................53
Setting the Test Tone ..........................................................................................................................................................55
Setting the DRC (Dynamic Range Compression) ..............................................................................................................56
Setting the Audio ...............................................................................................................................................................57
AV SYNC Setup..................................................................................................................................................................59
Sound Field (DSP)/EQ Function.........................................................................................................................................60
Dolby Pro Logic II Mode .....................................................................................................................................................61
Dolby Pro Logic II Effect .....................................................................................................................................................62
RADIO OPERATION
HDMI
HDMI transmits DVD video and audio signals simultaneously, and provides a clearer
picture.
5
Listening to Radio ...............................................................................................................................................................63
Presetting Stations..............................................................................................................................................................64
MISCELLANEOUS
Convenient Functions .........................................................................................................................................................65
Operating a TV with the Remote Control............................................................................................................................67
Before Calling for Service ...................................................................................................................................................69
Cautions on Handling and Storing Discs............................................................................................................................71
Language Code List............................................................................................................................................................72
Specifications......................................................................................................................................................................73
WARRANTY........................................................................................................................................................................74
6
Notes on Discs
ENG
DVD (Digital Versatile Disc) offers fantastic audio and video, thanks to Dolby Digital
Disc Recording Format
PREPARATION
surround sound and MPEG-2 video compression technology. Now you can enjoy these
realistic effects in the home, as if you were in a movie theater or concert hall.
VIDEO
CD-R Discs
• Some CD-R discs may not be playable depending on the disc recording device (CD-Recorder or PC) and the
1
~ 6
Home Theaters and the discs are coded by region. These regional codes must match in
order for the disc to play. If the codes do not match, the disc will not play.
The Region Number for this player is given on the rear panel of the player.
(Your Home Theater will only play DVDs that are labeled with identical region codes.)
Playable Discs
Disc Type
Mark (Logo)
CD-R MP3 Discs
Recorded Signals
Disc Size
5"
DVD-AUDIO
DVD-VIDEO
Audio + Video
3 1/2"
COMPACT
Audio
AUDIO-CD
DIGITAL AUDIO
•
•
•
condition of the disc.
Use a 650MB/74 minute CD-R. Other CD-R media, may not be playable.
Some CD-RW (Rewritable) media, may not be playable.
Only CD-Rs that are properly "closed" can be fully played. If the session is closed but the disc is left open,
you may not be able to fully play the disc.
Max. Playing Time
Approx. 240 min. (single-sided)
Approx. 480 min. (double-sided)
Approx. 80 min. (single-sided)
Approx. 160 min. (double-sided)
5"
74 min.
3 1/2"
20 min.
Do not use the following types of disc!
• Only CD-R discs with MP3 files in ISO 9660 or Joliet format can be played.
• MP3 file names should be 8 characters or less in length and contain no blank spaces or special characters (. / = +).
• Use discs recorded with a compression/decompression data rate greater than 128Kbps.
• Only files with the ".mp3" and ".MP3" extensions can be played.
• Only a consecutively written Multisession disc can be played. If there is a blank segment in the Multisession disc,
•
•
•
•
the disc can be played only up to the blank segment.
If the disc is not closed, it will take longer to begin playback and not all of the recorded files may be played.
For files encoded in Variable Bit Rate (VBR) format, i.e. files encoded in both low bit rate and high bit rate (e.g.,
32Kbps ~ 320Kbps), the sound may skip during playback.
A maximum of 500 tracks can be played per CD.
A maximum of 300 folders can be played per CD.
• LD, CD-G, CD-I, CD-ROM and DVD-ROM discs cannot be played on this player.
•
If such discs are played, a "WRONG DISC FORMAT" message appears on the TV screen.
DVD discs purchased abroad may not play on this player.
If such discs are played, a "WRONG REGION CODE" message appears on the TV screen.
Copy Protection
• Many DVD discs are encoded with copy protection. Because of this, you should only connect
•
7
your Home Theater directly to your TV, not to a VCR. Connecting to a VCR results in a distorted
picture from copy-protected DVD discs.
This product incorporates copyright protection technology that is protected by methods claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
CD-R JPEG Discs
• Only files with the ".jpeg" and ".JPEG" extensions can be played.
• If the disc is not closed, it will take longer to start playing and not all of the recorded files may be played.
• Only CD-R discs with JPEG files in ISO 9660 or Joliet format can be played.
• JPEG file names should be 8 characters or less in length and contain no blank spaces or special characters (. / = +).
• Only a consecutively written multisession disc can be played. If there is a blank segment in the multisession disc, the
•
•
•
disc can be played only up to the blank segment.
A maximum of 9,999 images can be stored on a single CD.
When playing a Kodak/Fuji Picture CD, only the JPEG files in the picture folder can be played.
Picture discs other than Kodak/Fuji Picture CDs may take longer to start playing or may not play at all.
8
Description
ENG
Power (
) button
Disc Tray
Standby indicator
—Rear Panel—
External Digital Optical Input Connector
Tuning Up & Skip ( ) buttons
Tuning Down & Skip ( ) buttons
DSP/EQ button
Function button
Use this to connect external equipment capable of digital output.
Volume control
Open/Close button
Direct Play buttons
Video Output Connector
Anynet Input/Output
Connector
External Video Input Connectors
Connect the TV's video input jacks
(VIDEO IN) to the VIDEO OUT connector.
External Audio Input Connectors
AM Antenna
Connector
Disc Change
button
FM Antenna Connector
Cooling Fan
Remote Control Sensor
Headphone Jack
SUB TITLE button
MUTE button
Play/Pause (
Stop (
) button
COMPONENT VIDEO OUTPUT
Connectors
5.1 Channel Speaker
Output Terminals
HDMI Output/Input
Connector
) button
Connect a TV with component video inputs
to these jacks.
S-Video Output Connector
If the TV is equipped with an S-Video input
connector (S-VIDEO IN), connect it to the
player's S-Video output.
PRO LOGIC II indicator
LINEAR PCM indicator
DTS Disc
indicator
GROUP indicator
CHAPTER indicator
TRACK indicator
PROGRAM indicator
TITLE
TUNER indicator
REPEAT indicator
indicator
STEREO indicator
Accessories
Remote Control
(AH59-01512A)
DVD AUDIO indicator
Video Cable
(AH39-40001V)
Anynet Cable
(AH39-40001Z)
FM Antenna
(AH42-00017A)
User's Manual
(AH68-01663R)
DISC(1~5)
indicator
System Status Display
SPEAKER indicator
DOLBY DIGITAL indicator
DSP indicator
RADIO FREQUENCY
indicator
9
AM Antenna
(AH42-00019A)
10
PREPARATION
—Front Panel—
Description
ENG
PREPARATION
—Remote Control—
Insert Remote Batteries
TV indicator
TV, DVD POWER button
MODE button
DISC SKIP button
DVD RECEIVER indicator
OPEN/CLOSE button
TV/VIDEO, DIMMER button
DVD button
Number(0~9) buttons
REMAIN button
AUX button
TUNER button
1
Remove the battery
cover on the back
of the remote by
pressing down and
sliding the cover in
the direction of the
arrow.
2
Insert two 1.5V AAA
batteries, paying
attention to the correct
polarities (+ and –).
3
Replace the battery
cover.
CANCEL button
Play/Pause button
Stop button
Tuning Preset/CD Skip button
PL II MODE button
VOLUME button
MENU button
SUB TITLE button
PL II EFFECT button
TUNING/CH button
INFO. button
AUDIO button
Caution
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match the polarity:(+) to (+)and (–)to (–).
• Use the correct type of batteries.Batteries that look similar may differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
Cursor/Enter button
RETURN button
REPEAT button
STEP button
ZOOM button
LOGO COPY button
SLEEP button
SLOW, MO/ST button
HDMI AUDIO button
MUTE button
EZ VIEW button
TEST TONE button
SOUND EDIT button
DSP/EQ button
Range of Operation of the Remote Control
The remote control can be used up to approximately 23 feet/7 meters in a straight line. It can also be
operated at a horizontal angle of up to 30° from the remote control sensor.
TUNER MEMORY, DCDi button
SD/HD button
SLIDE MODE button
DIGEST button
11
12
Connecting the Speakers
ENG
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
Center Speaker
Front Speaker (R)
Front Speaker (L)
C
Green
SW
L
R
Red
White
CONNECTIONS
SL
SR
Purple
Gray
Rear Speaker (R)
Position of the Home Theater
• Place it on a stand, cabinet shelf, or under the
TV stand.
Selecting the Listening Position
position, facing inwards (about 45°) toward you.
the same height as your ear.
• Align the front face of the front speakers with the
front face of the center speaker or place them
slightly in front of the center speakers.
Rear Speakers SL SR
• Place these speakers behind your listening position.
• If there isn't enough room, place these speakers so they face each
•
other.
Place them about 60 to 90cm (2 to 3feet) above your ear, facing
slightly downward.
*
Center Speaker
• It is best to install it at the same height as the front
C
speakers.
• You can also install it directly over or under the TV.
Rear Speaker (L)
Subwoofer
The listening position should be located about 2.5 to 3
times the distance of the TV's screen size away from the
TV. Example: For 32" TVs 2~2.4m (6~8 feet)
For 55" TVs 3.5~4m (11~13 feet)
Front Speakers L R
• Place these speakers in front of your listening
• Place the speakers so that their tweeters will be at
Blue
Back of the Speakers
1 Press down the terminal 2 Insert the black wire into
tab on the back of the
speaker.
the black terminal (–) and
the gray wire into the gray
(+) terminal, and then
release the tab.
Black
Back of the Main Unit
3 Connect the connecting plugs to
the back of the Home Theater.
• Make sure the colors of the speaker terminals
match the colors of the connecting plugs.
Gray
Unlike the front and center speakers, the rear speakers are used
to handle mainly sound effects and sound will not come from
them all the time.
Subwoofer SW
• The position of the subwoofer is not so critical.
Place it anywhere you like.
13
14
Connecting the Video Out to TV
Choose one of the four methods for connecting to a TV.
Connecting the HDMI IN/OUT
HDMI (High-Definition Multimedia Interface) is a next generation TV-type digital interface specification
that enables transmitting digital video and audio over a single cable. In addition, it enables you to enjoy
multi-channel digital audio.
Set-top box or
DVD player
HT-HDP40
Red
ENG
Blue
Green
CONNECTIONS
METHOD 1
(supplied)
METHOD 4
METHOD 2
Red
METHOD 3
Blue
Green
not supplied
not supplied
TV
METHOD 1 Composite Video ....... (Good Quality)
- Connect the supplied video cable from the VIDEO OUT jack on the back panel of the system
to the VIDEO IN jack on your TV.
1
Connect the HDMI IN port of this unit and the HDMI OUT port of a set-top box
or the DVD player.
2
Connect the HDMI OUT port of this unit and the HDMI IN port of your TV.
3
Press AUX on the remote control to select ‘HDMI IN.
METHOD 2 S-Video ....... (Good Quality)
- If your television is equipped with an S-Video input, connect an S-Video cable (not supplied) from
the S-VIDEO OUT jack on the back panel of the system to the S-VIDEO IN jack on your television.
METHOD 3 Component ....... (Better Quality)
- If your television is equipped with Component Video inputs, connect a component video cable
(not supplied) from the Pr, Pb and Y jacks on the back panel of the system to the corresponding
jacks on your TV.
METHOD 4 HDMI ....... (Best Quality)
- Connect the HDMI out to the HDMI input on your TV.
Note
• This product operates in Progressive scan mode(480p Only ) for Component Output.
• If the TV only supports a resolution of 576i(480i), the screen may be divided into 2 screens, or
display nothing.
15
• Each time the button is pressed, the selection changes as follows:
•
HDMI IN➝ DIGITAL IN➝ AUX 1 ➝ AUX 2.
You can also use the FUNCTION button on the main unit.
The mode switches as follows: DVD/CD ➝ HDMI IN ➝ DIGITAL IN ➝ AUX 1 ➝ AUX 2 ➝ FM ➝ AM.
Note
• When this unit is turned off, no HDMI video or audio signal is output from this unit.
• In the HDMI IN Function, the video resolution switch button (SD/HD) does not work.
• When the output from an external device, which is connected to this device, is DVI, no audio will be
output. In this case, you can listen to the digital audio by connecting the Optical OUT of the source
device and the Optical IN of this device, even if the source device and this device is connected through
DVI interface.
16
HDMI Function
ENG
What is HDMI (High Definition Multimedia Interface)?
This device transmits DVD video signal digitally without the process of converting to analog.
You can get sharper digital pictures by connecting the video to your TV using an HDMI
connection cable.
Resolution Selection
• This function allows the user to select screen resolution for HDMI output.
• The audio signals transmitted over the HDMI Cable can be toggled
ON/OFF.
In Stop mode, press and hold the SD/HD (Standard Definition/High
Definition)button on the remote control.
Press the HDMI AUDIO button on the remote
control.
• Resolutions available for the HDMI output are 480P, 720P and 1080i.
• SD(Standard Definition) resolution is 480p and HD(High Definition) resolution is 720p/1080i.
• This toggles between “AUDIO ON” and “AUDIO OFF” on the display.
• AUDIO ON : Both video and audio signals are transmitted over the
•
Note
HDMI connection cable, and audio output is through the TV speakers
only.
AUDIO OFF : Video is transmitted over the HDMI connection cable only,
and audio output is through the home theater speakers only.
CONNECTIONS
HDMI Audio ON/OFF function
Example: If the TV supports resolution up to 480p
Press the SD/HD button.
• A 480p video signal is output through the HDMI output.
• If the TV does not support the configured resolution, you will not be able to see the picture properly.
• The default setting value of this product is HDMI AUDIO OFF.
• HDMI AUDIO is automatically down-mixed to 2ch for TV speakers.
• If you turn the unit off and on, or switch functions when the HDMI AUDIO
is set to ON, the HDMI AUDIO is automatically set to OFF.
Note
DCDi (Directional Correlational Deinterlacing) Function
Converts the interlace signal to progressive to prevent flickering and to
remove distortion or noise on the edge of screen.
Press and hold DCDi button on the remote
control for over 3 seconds.
• Each time the button is pressed, the selection alternates between
DCDi ON and DCDi OFF.
17
• Since this product has an embedded Video Upscaler function with Faroudja DCDi technology, it can
enhance a 576i(480i) DVD resolution output to 480p/720p/1080i.
• You do not have to make separate adjustments, since the Home Theater and TV will be automatically
adjust themselves to the optimal resolution and aspect ratio if connected to HDMI. (If the TV is an HDTV
and has an HDMI Input jack, output is automatically converted to 1080i resolution (if supported by the TV).)
• For component video output, only 480P is supported.
• When both HDMI and COMPONENT jacks are connected, COMPONENT video is not displayed.
• See your TV owner's manual for more information on how to select the TV's Video Input source.
18
Connecting External Components
ENG
Connecting an External Digital Component
Connecting an External Analog Component
Example: Digital signal components such as a Settop Box or CD Recorder.
Example: Analog signal components such as a VCR or TV.
CONNECTIONS
Audio Cable
Optical Cable
(not supplied)
Video Cable
External Digital
Component
TV
External Analog
Component
1
Connect Video Out on the Home Theater to Video In on the TV.
1
Connect Video Out on the Home Theater to
Video In on your TV.
2
Connect Video In on the Home Theater to Video Out on the external digital component.
2
Connect Video In on the Home Theater to
Video Out on the external analog component.
3
Connect the Digital Input (OPTICAL) to the Digital Output on the external digital component.
3
Connect Audio In on the Home Theater to Audio
Out on the external analog component.
4
Press AUX on the remote control to select ‘DIGITAL IN’.
• Each time the button is pressed, the selection changes as follows: HDMI IN➝ DIGITAL IN➝ AUX 1 ➝ AUX 2.
• You can also use the FUNCTION button on the main unit.
The mode switches as follows: DVD/CD ➝ HDMI IN ➝ DIGITAL IN ➝ AUX 1 ➝ AUX 2 ➝ FM ➝ AM.
If the external analog
component has only
one Audio Out, connect
either left or right.
• Be sure to match connector colors.
4
Press AUX on the remote control to select AUX 1
or AUX 2 input.
• Each time the button is pressed, the selection changes as
follows: HDMI IN➝ DIGITAL IN➝ AUX 1 ➝ AUX 2.
TV
Note
• If you have connected an external digital
component and also an Analog
component to Video In (1, 2) at the same
time, there will be video from AUX 1 even
when you select DIGITAL IN.
• If you have connected Audio In (L, R) to
1, connect Video In to 1 as well, and if
you have connected Audio In (L, R) to 2,
connect Video In to 2 also.
• When you select Aux 1 or 2, you are
selecting Video 1 or 2 inputs respectively.
• You can also use the FUNCTION button on the main unit.
The mode switches as follows: DVD/CD ➝ HDMI IN ➝
DIGITAL IN ➝ AUX 1 ➝ AUX 2 ➝ FM ➝ AM.
19
20
How to Connect to Anynet
Connecting the FM and AM Antennas
ENG
Using a Samsung Anynet-enabled TV, you can control the DVD Home Theater System and any other
Samsung Anynet-enabled AV device. For detailed operation instructions and connection diagram, refer
to the user's manual of your Samsung Anynet-enabled TV.
If AM reception is poor, connect an
outdoor AM antenna(not supplied).
What is Anynet?
AM Loop Antenna
(supplied)
FM Antenna (supplied)
Snap the tabs on the loop into the
slots of the base to assemble the
AM loop antenna.
Use this to connect
Anynet-enabled AV
devices.
FM antenna connection
1
Connect the Anynet input terminal on the back of this unit to your Samsung TV's Anynet
output terminal.
2
Connect the Anynet Out Terminal on the back of this unit to the Anynet input of Samsung
external AV devices.
3
Refer to the user's manual of your Anynet-enabled TV and activate the Anynet function.
* This function is available only with Samsung Anynet-enabled TVs.
Caution
• If the Anynet input and output terminals are reversed, communication with the TV will fail and
you will not be able to use the Anynet function.
1. Connect the FM antenna supplied to the FM
75Ω COAXIAL terminal.
2. Slowly move the antenna wire around until
you find a location where reception is good,
then fasten it to a wall or other rigid surface.
Cooling Fan
AM antenna connection
1. Connect the AM loop antenna supplied
to the AM and
terminals.
2. If reception is poor, connect an outdoor
single vinyl-covered wire to the AM
terminal. (Keep the AM loop antenna
connected).
The cooling fan supplies cool air to the unit to prevent overheating.
Please observe the following cautions for your safety.
• Make sure the unit is well-ventilated. If the unit has poor ventilation, the temperature inside the unit could rise
and may damage it.
• Do not obstruct the cooling fan or ventilation holes. (If the cooling fan or ventilation holes are covered with a
newspaper or cloth, heat may build up inside the unit and fire may result.)
21
22
CONNECTIONS
• The Anynet function allows you to use your Samsung TV's remote control and menu to control all AV devices.
• However, this function is available only with Samsung Anynet-enabled models.
Before Using Your Home Theater
ENG
Disc terminology
Your Home Theater is capable of playing DVD, CD, MP3 and JPEG discs.Depending on the disc you are using,
these instructions may vary slightly. Read the instructions carefully before using.
Groups and tracks (DVD-AUDIO)
• DVD-audio is divided into several large sections called "groups" and
smaller sections called "tracks". Numbers are allotted to these sections.
These numbers are called "group numbers" and "track numbers".
To Operate your Samsung TV and the Home Theater with the HT-HDP40's Remote Control
GROUP 1
2
Press MODE button
until the TV indicator
lights red.
3
TRACK 1
Press the POWER
button to turn on the
TV.
TRACK 2
TRACK 3
TRACK 1
TRACK 2
Titles and chapters (DVD-VIDEO)
TV
• DVD-video is divided into several large sections called "titles" and smaller
DVD RECEIVER
sections called "chapters". Numbers are allotted to these sections.
These numbers are called "title numbers" and "chapter numbers".
TITLE 1
CHAPTER 1
4
Press TV/VIDEO
button to select
VIDEO mode.
5
Press the MODE
button until the DVD
RECEIVER indicator
lights green.
TV
6
Press FUNCTION button
on the main unit or DVD
on the remote to select
DVD/CD mode.
CHAPTER 2
TITLE 2
CHAPTER 3
CHAPTER 1
CHAPTER 2
Tracks (Video and music CDs)
• Video and music CDs are divided into sections called "tracks".
Numbers are allotted to these sections. These numbers are called
"track numbers".
TRACK 1
DVD RECEIVER
TRACK 2
TRACK 3
TRACK 4
TRACK 5
Files (DivX)
• DivX is divided into sections called "files".
Numbers are allotted to these sections. These numbers are called
"file numbers".
Note
FILE 1
• Buttons Enabled for TV Operation: POWER, CHANNEL, VOLUME, TV/VIDEO, and Numeric (0-9) buttons.
• By default, the remote control is set to work with Samsung TVs.
FILE 2
See page 67 for more information about remote control operation with other manufacturer's TVs.
Note
23
• In this manual, the instructions marked with "DVD (
DVD
)" are applicable
to DVD-VIDEO, DVD-AUDIO, and DVD-R/RW discs.
Where a particular DVD type is mentioned, it is indicated separately.
• Depending on the content of the disc, the initial screen may appear different.
24
CONNECTIONS
1
Plug the main unit's
power cord into the
AC power supply.
GROUP 2
Disc Playback
Selecting a Disc in the Disc changer
ENG
The DVD/CD function is automatically selected when Disc Skip is pushed.
1
Press OPEN/CLOSE button to open the
disc tray.
2
Load a disc.
3
Press DISC SKIP button.
To select a specific disc, press the corresponding DIRECT PLAY
(1, 2, 3, 4, 5) buttons on the front panel or DISC SKIP on the
remote control, until the required disc indicator flashes.
• If the disc selected is not loaded, the next disc is played automatically.
• Place a disc gently into the tray with the disc’s label
facing up.
OPERATION
• Rotate the carousel tray so you can load the third, fourth,
and fifth discs.
To stop playback, press STOP during playback.
• If pressed once, “PRESS PLAY” is displayed and the stop position will be stored in memory.
4
Close the compartment by pressing the
OPEN/CLOSE button again.
DVD
If PLAY/PAUSE (
) button or ENTER button is pressed, playback resumes from the stop position.
(This function works only with DVDs.)
• If pressed twice, “STOP” is displayed, and if PLAY/PAUSE (
) button is pressed, playback starts from the
beginning.
CD
• Playback starts automatically.
To temporarily pause playback, press PLAY/PAUSE during playback.
• To resume playback, press PLAY/PAUSE (
Note
25
) button again.
• Depending on the content of the disc, the initial screen may appear different.
• Depending on the recording mode, some MP3-CDs cannot be played.
• Table of contents of a MP3-CD varies depending on the MP3 track format recorded on the disc.
26
MP3-CD Playback
Displaying Disc Information
Data CDs (CD-ROM, CD-R, CD-RW) encoded in MP3 format can be played.
1
Press the
OPEN/CLOSE button
to open the disc tray,
and then load the
MP3 disc.
• The MP3 menu screen will appear and
•
You can view disc playback information on the TV screen.
2
In Stop mode, use
to select
the album, and then
press the ENTER
button.
• User
• Each time the button is pressed, the display changes as follows:
DVD
CD
MP3
The information display
disappears from the screen
4
Press the STOP
button to stop
playback.
•
Note
• Depending on the recording mode, some MP3-CDs may not play.
• Table of contents of a MP3-CD varies depending on the MP3 track format
•
To play a file icon in the screen,
• To play music files only, select the
• To view image files only, select the
• To view movie files only, select the
Icon.
• To select all files select the
27
Icon.
Icon.
different.
Depending on the disc, you can also select DTS, DOLBY DIGITAL,
or PRO LOGIC.
Screen Display
DVD display
Press the
button when it is in stop
status and select a desired icon from the top
part of the menu.
• Depending on the disc, the disc information display may appear
•
recorded on the disc.
MP3 file support: MPEG1 LAYER3 (BITRATE : 128KBPS~320KBPS ,
SAMPLING FREQ.: 32K/44.1K/48KHz)
The information display
disappears from the screen
appears on the TV screen!
repeat Steps 2 and 3 above.
Note
JPEG
If this symbol appears on the TV screen while buttons are being operated,
that operation is not possible with the disc currently being played.
The information display
disappears from the screen
• To select another album and track,
DivX
TITLE display
ELAPSED TIME display
STEREO (L/R) display
REPEAT PLAYBACK display
DOLBY DIGITAL display
AUDIO LANGUAGE display
ANGLE display
CD display
GROUP display
• Music File Icon
• Image File Icon
• Movie File Icon
• All File Icon
DivX display
MP3 CD display
DVD DVD-AUDIO display
AUDIO
CHAPTER display
TRACK (FILE) display
SUBTITLE display
Icon.
28
OPERATION
3
Press INFO button.
to select the track.
playback will start.
The appearance of the menu depends on
the MP3 disc.
To change the album,
use
to
select another album
in Stop mode, and
then press the
ENTER button.
ENG
JPEG File Playback
JPEG
Images captured with a digital camera or camcorder, or JPEG files on a PC can be stored on a CD and then
played back with this Home Theater.
ENG
Digest Function
You can view 9 JPEG images on the TV screen.
1
Slide Mode
Press DIGEST
button during
playback.
2
• JPEG files will be shown in
• The selected image is played for 5 seconds before moving to
9 windows.
1
Place the JPEG disc on the disc tray.
2
Press the OPEN/CLOSE button.
Press Cursor , , , buttons
to select the desired image and
then press ENTER button.
the next image.
To view the previous or next image with 9 windows, press
.
OPERATION
Rotate/Flip Function
3
Press SLIDE MODE button.
Press Cursor
,
,
,
buttons during playback.
• Playback starts automatically.
• Each time the button is pressed, the image makes the transition as follows:
From top to bottom
button: Flip Vertically
From bottom to top
button: Rotate 90°
Counterclockwise
Rectangular shape in the center
button: Rotate 90° Clockwise
Original Image
Vertical blinds effect
button: Flip Horizontally
Each time a new image is displayed, slide modes
(1~11) will be applied randomly and automatically.
JPEG limitation
Cancels the slide mode.
29
Press
to skip to the next slide.
• Each time the button is pressed, the slide moves backward or forward.
The maximum resolution is 5120 x 3840 (or 19.0 MPixel) for baseline images, and 2048 x 1536
(3.0 MPixel) for progressive images.
There is no filesize limitation.
The decoder is device independent, thus above applies to USB and other devices as well.
☞ Progressive JPEG images — those that appear gradually as the image is being downloaded.
30
DivX Playback
ENG
Subtitle Display
Press the SUBTITLE button.
Skip Forward/Back
During playback, press the
button.
• Goes to the next file whenever you press
button, if there are over
•
2 files in the disk.
Goes to the previous file whenever you press
over 2 files in the disk.
button, if there are
• Each time you press the button, your selection will toggle between “SUBTITLE ON” (1/1, 1/2 ...) and
“SUBTITLE OFF”.
• If the disc has only one subtitle file, it will be played automatically.
Audio Display
Press the AUDIO button.
Fast playback
• Each time you press the button, your selection will toggle between “AUDIO ON” (1/1, 1/2 ...) and
To play back the disc at a faster speed,
press and hold
or
during playback.
change as follows:
2x ➞ 4x ➞ 8x ➞ 32x ➞ Normal.
During playback, press the
DivX(Digital internet video eXpress)
1. Supported Formats
,
• This product only provides the following media formats. If both video and audio formats are not
supported, the user may experience problems such as broken images or no sound.
button.
• Playback skips 5 minutes forward whenever you press
• Playback skips 5 minutes back whenever you press
●
button.
button.
WMV
V1/V2/V3/V7
MP3
WMA
80~384kbps
56~128kbps
44.1khz
AC3
128~384kbps
44.1/48khz
DTS
1.5Mbps
44.1khz
• Aspect Ratio: Although default DivX resolution is 640*480 pixels (4:3), this product supports up to
2
Press Cursor , ,
, buttons to
move to the area
you want to enlarge.
• Each time you press the button,
720*480 pixels (16:9). TV screen resolutions higher than 800 will not be supported.
• When you play a disc whose sampling frequency is higher than 48khz or 320kbps, you may
experience shaking on the screen during playback.
2. Caption Function
• You must have some experience with video extraction and editing in order to use this feature properly.
• To use the caption function, save the caption file (*.smi) in the same file name as that of the DivX
your selection will toggle between
“ZOOM X2” and “ZOOM OFF”.
31
AVI
DivX3.11 ~ 5.1
Supported Audio Formats
Format
Bit Rate
Sampling Frequency
Zoom Function
Note
Supported Video Formats
Format
Supported Versions
●
Press ZOOM
button.
" is displayed when there is one supported language in the disc.
DivX is a video file format developed by Microsoft based on the MPEG4 to provide audio and video
data over the Internet in real-time.
MPEG4 is used for video encoding and MP3 for audio encoding so that the users can watch a movie
at near DVD-quality video and audio.
5 Minute Skip function
1
•"
”.
• DIVX file can be zoomed only in ZOOM X2 mode.
• Zoom function is not available when playing a MPEG1 video file.
•
media file (*.avi) within the same folder.
Example. Root
Samsung_Bluetek_007CD1.avi
Samsung_Bluetek_007CD1.smi
Up to 60 alphanumeric characters or 30 East Asian characters (2 byte characters such as Korean and
Chinese) for the file name.
32
OPERATION
• Each time you press and hold either button, the playback speed will
Note
“
Checking the Remaining Time
Fast/Slow Playback
Fast Playback
DVD
CD
Slow Playback
MP3
Press the REMAIN button.
Press and hold
• For checking the total and remaining time of a title or chapter
• Each time the button is held down during playback,
being played.
.
the playback speed changes as follows:
Press SLOW button.
• Each time the button is pressed during playback,
the playback speed changes as follows:
DVD
Each time the REMAIN button is pressed
DVDAUDIO
TITLE ELAPSED
GROUP ELAPSED
TITLE REMAIN
GROUP REMAIN
CHAPTER ELAPSED
TRACK ELAPSED
CHAPTER REMAIN
TRACK REMAIN
DivX
Note
• Reverse slow playback
does not work with DivX.
Skipping Scenes/Songs
CD
MP3
Briefly press
.
• Each time the button is pressed briefly during playback, the previous or next chapter, track,
TRACK ELAPSED
TRACK REMAIN
TRACK REMAIN
TRACK ELAPSED
TOTAL ELAPSED
or directory (file) will be played.
• You cannot skip chapters consecutively.
DVD
MP3
TITLE 01/05 CHAPTER 002/040
TOTAL REMAIN
TITLE 01/05 CHAPTER 004/040
33
34
OPERATION
DVDVIDEO
ENG
Repeat Playback
A-B Repeat Playback
Repeat playback allows you to repeatedly play a chapter, title, track (song), or directory (MP3 file).
DVD
CD
MP3
You can repeatedly play back a designated section of a DVD.
JPEG
DVD
Press REPEAT button.
• Each time the button is pressed during playback, the repeat playback mode changes as follows:
DVDVIDEO
ENG
DVDAUDIO
Repeat Playback Options
CHAPTER
Repeatedly plays the selected chapter.
1
CD
Press INFO button
twice.
2
Press Cursor button
to move to REPEAT
PLAYBACK ( ) display.
4
Press ENTER
button at the end
of the desired
segment.
• For a CD, press INFO button
once.
TITLE
Repeatedly plays the selected title.
GROUP
Repeatedly plays the selected group.
JPEG
CD
TRACK
Repeatedly plays the selected track.
DIR
Repeatedly plays all tracks in the selected folder.
3
Press Cursor , buttons
to select ‘A-’ and then press
ENTER button at the beginning
of the desired segment.
• When ENTER button is pressed,
the selected position will be stored
in memory.
• The specified segment will be
played repeatedly.
A-
DISC
Repeatedly plays the entire disc.
A-B
REPEAT : A—B
OFF
Cancels Repeat Playback.
A -?
REPEAT : A—
To Select a Repeat Playback Mode in the Disc Information Screen
1
2
35
DVD
Press INFO button twice.
To return to normal playback, press Cursor
buttons to select
OFF.
,
Press Cursor button to move to
REPEAT PLAYBACK ( ) display.
Note
3
Press Cursor button to select the
desired Repeat Playback mode.
4
Press ENTER button.
MP3 and JPEG discs, you cannot select Repeat
* For
Play from the information display screen.
CD
• The A-B Repeat function will not work on an MP3 or JPEG disc.
36
OPERATION
MP3
RANDOM
Plays tracks in random order.
(A track that has already been played may be
played again.)
Step Function
Zoom (Screen Enlarge) Function
DVD
This function allows you to enlarge a particular area of the displayed image.
ENG
DVD
Press STEP button.
• The picture moves forward one frame each time the button is pressed
during playback.
Note
• During fast playback of a CD or MP3-CD, sound is heard only at 2x speed,
and not at 4x, 8x, and 32x speeds.
1
Press ZOOM
button.
2
Press Cursor , ,
, buttons to
move to the area
you want to enlarge.
• No sound is heard during slow playback and step motion playback.
3
Press ENTER
button.
• Each time the button is pressed, the
zoom level changes as follows:
SELECT ZOOM POSITION
Angle Function
DVD
This function allows you to view the same scene in different angles.
Press INFO button.
2
1/3
3
1/3
Press Cursor , or numeric buttons to
select the desired angle.
• Each time the button is pressed, the angle changes as follows:
1/3
EZ VIEW Function
OPERATION
1
Press Cursor
button to move to
ANGLE ( ) display.
DVD
Press EZ VIEW button.
• Each time the button is pressed, the zoom function will switch between On
and Off.
• When a movie is played in Widescreen format, black bars at the top and
bottom of the TV screen can be removed by pressing the EZ VIEW button.
2/3
3/3
EZ VIEW
EZ VIEW OFF
Note
Note
37
• The Angle function works only with discs on which multiple
angles have been recorded.
• This function will not work if the DVD is recorded with multi-camera angle format.
• Black bars may not disappear because some DVD discs have a built-in horizontal to vertical ratio.
38
Bonus Group / Navigating Pages
Bonus Group
Selecting Audio/Subtitle Language
Audio Language Selection Function
DVDAUDIO
Some DVD-Audio discs have an extra ‘bonus’ group that requires a 4-digit key
number to access. See the disc packaging for details and the-key number.
1
Press INFO button
twice.
When you play a DVD-Audio disc that has a
bonus group, the key number input screen
appears automatically.
2
ENG
DVD
Press Cursor ,
buttons or numeric
buttons to select the
desired audio language.
• Depending on the number of languages on a
DVD disc, a different audio language
(ENGLISH, SPANISH, FRENCH, etc.) is
selected each time the button is pressed.
SP 2/3
FR 3/3
BONUS GROUP
OPERATION
KEY NUMBER :
Subtitle Language Selection Function
Note
• If you eject the disc, switch the power off, or unplug the player, you will need to re-enter
1
Press INFO button
twice.
3
Press Cursor
button or numeric
buttons to select
the desired subtitle.
the key number.
Navigating Pages
Press Cursor
button to move to
SUBTITLE ( )
display.
DVDAUDIO
During playback, press the TUNING/CH button
on the remote control.
• You can select the desired image from a DVD-Audio disc containing still images.
• With some discs, you may not be able to select images depending on how the
disc was manufactured.
2
DVD
EN 1/3
EN 01/ 03
OFF
SP 02/ 03
Note
FR 03/ 03
OFF / 03
• You can use the SUBTITLE button
•
39
on the remote control to select a
subtitle language.
Depending on the disc, the Subtitle
and Audio Language functions may
not work.
40
Moving Directly to a Scene/Song
Using Disc Menu
ENG
DVD
You can use the menus for the audio language, subtitle language, profile, etc.
DVD menu contents differ from disc to disc.
DVD
1
CD
Moving to a Title/Track
01/05
001/040
0:00:37
1/1
03/05
025/040
0:00:01
0:00:01
5
1/1
Press Cursor ,
buttons to move to
time display.
01/05
025/040
1:17:30
3
1
2
Press Cursor ,
buttons to move to
‘DISC MENU’ and then
press ENTER button.
• When you select Disc Menu and it is not
3
Press Cursor ,
, buttons to
select the desired
item.
• Press ENTER button.
supported by the disc, the "This menu is not
supported" message appears on the screen.
01/05
1/1
Moving to a Specific Time
Press Cursor ,
buttons or numeric buttons
to select the desired
chapter and then press
ENTER button.
01/05
001/002
Press Cursor ,
buttons to move to
Chapter ( ) display.
In Stop mode,
press MENU
button.
001/040
0:00:01
1/1
Moving to a Specific Time
6
Press the numeric
buttons to select the
desired time and then
press ENTER button.
1/1
01/05
028/040
1:30:00
1/1
OPERATION
Moving to a Chapter
4
2
Press INFO button.
Press Cursor , buttons
or numeric buttons to select
the desired title/track and then
press ENTER button.
Moving to a Chapter
• Disc menu display may be different depending on the disc.
Note
Using the Title Menu
DVD
For DVDs containing multiple titles, you can view the title of each movie.
Depending on the disc, the availability of this feature may vary.
MP3
1
JPEG
Press the numeric
buttons.
• The selected file will be played.
• An MP3 or JPEG disc cannot be moved
in the disc information screen.
Note
In Stop mode,
press MENU
button.
2
Press Cursor ,
button to move to
‘Title Menu’.
• You can press
•
3
Press ENTER
button.
• The title menu appears.
on the
remote control to move directly to the
desired title, chapter, or track.
Depending on the disc, you may not
be able to move to the selected title
or time.
• When playing an MP3 or JPEG disc, you
cannot use
,
to move to a folder.
To move a folder, press (Stop) and
then press
, .
Press MENU button to exit the setup screen.
41
Note
• Title menu display may be different depending on the disc.
42
Setting the Language
ENG
OSD (On-Screen Display) language is set to English by default.
1
In Stop mode,
press MENU
button.
2
Press Cursor
button to move to
‘Setup’ and then
press ENTER button.
3
Select ‘Language’
and then press
ENTER button
4
Press Cursor ,
button to select ‘OSD
Language’ and then
press ENTER button.
5
Press Cursor ,
button to select the
desired language and then
press ENTER button.
• Once the setup is complete, if the language was
set to English, OSD will be displayed in English.
Press MENU button to exit the setup screen.
Note
• To select another language, select OTHER and enter the language code of your country.
(See page 72 for language codes)
AUDIO, SUB TITLE and DISC MENU language can be selected.
Selecting the
OSD Language
Selecting the
Audio Language
(recorded on the disc)
Selecting the
Subtitle Language
(recorded on the disc)
Selecting the Disc Menu
Language (recorded on the disc)
language you selected is
* Ifnottherecorded
on the disc, menu
language will not change even
if you set it to your desired
language.
43
44
SETUP
Press RETURN button to return to the previous level.
Setting TV Screen type
ENG
Depending on your TV type (Wide Screen or conventional 4:3), you can select the TV's aspect ratio.
1
In Stop mode,
press MENU
button.
2
Press Cursor
button to move to
‘Setup’ and then
press ENTER button.
Adjusting the TV Aspect Ratio (Screen Size)
The horizontal to vertical screen size ratio of conventional TVs is 4:3, while that of widescreen and high
definition TVs is 16:9. This ratio is called the aspect ratio. When playing DVDs recorded in different
screen sizes, you should adjust the aspect ratio to fit your TV or monitor.
• For a standard TV, select either "4:3LB" or "4:3PS" option according to personal preference.
Select "16:9" if you have a widescreen TV.
WIDE
: Select this to view a 16:9 picture in the full-screen
mode on your widescreen TV.
• You can enjoy the widescreen aspect.
4:3LB
3
Press Cursor
button to move to ‘TV
DISPLAY’ and then
press ENTER button.
4
Press Cursor ,
button to select the
desired item and then
press ENTER button.
• Once the setup is complete, you will
(4:3 Letterbox)
: Select this to play a 16:9 picture in the letter box
mode on a conventional TV.
• Black bars will appear at the top and bottom of the screen.
4:3PS
(4:3 Pan&Scan)
: Select this to play a 16:9 picture in the pan & scan
mode on a conventional TV.
Note
SETUP
• You can see the central portion of the screen only (with the
sides of the 16:9 picture cut off).
be taken to the previous screen.
• If a DVD is in the 4:3 ratio, you cannot view it in widescreen.
• Since DVD discs are recorded in various image formats, they will look different depending on
the software, the type of TV, and the TV aspect ratio setting.
Press RETURN button to return to the previous level.
Press MENU button to exit the setup screen.
45
46
Setting Parental Controls (Rating Level)
Use this to restrict playback of adult or violent DVDs you do not want children to view.
1
3
4
Press Cursor , button
to select the desired rating
level and then press
ENTER button.
• If you have selected Level 6, you
•
cannot view DVDs with Level 7 or
higher.
The higher the level, the closer the
content is to violent or adult material.
2
You can set the password for the Parental (rating level) setting.
Press Cursor
button to move to
‘Setup’ and then
press ENTER button.
1
3
5
Enter the password
and then press
ENTER button.
Press Cursor button to
move to ‘PASSWORD’
and then press ENTER
button.
Press MENU button.
4
Press ENTER
button.
5
Enter the password
and then press
ENTER button.
password, and confirm new password.
• The setting is complete.
• The password is set to "7890" by default.
• Once the setup is complete, you will be
taken to the previous screen.
• This function works only if a DVD disc contains the rating level information.
• The password is set to "7890" by default.
If you have forgotten the rating level password, do the following:
• While the player is in the no disc mode, hold the main unit's
Press RETURN button to return to the previous level.
47
2
Press Cursor
button to move to
‘Setup’ and then
press ENTER button.
• Enter the old password, a new
Note
Note
ENG
SETUP
Press Cursor
button to move to
‘PARENTAL’ and then
press ENTER button.
In Stop mode,
press MENU
button.
Setting the Password
Press MENU button to exit the setup screen.
on the display and all settings will return to the default values.
• Press the POWER button.
Using the RESET function will erase all stored settings.
Do not use this unless necessary.
button for longer than 5 seconds. “INITIALIZE” appears
48
Setting the Wallpaper
JPEG
ENG
DVD
While watching a DVD or JPEG CD, you can set the image you like as background wallpaper.
Setting the Wallpaper
1
During playback, press
PLAY/PAUSE button
when an image you
like appears.
To select one of the 3 wallpaper settings you've made
2
Press LOGO
button.
1
In Stop mode,
press MENU
button.
4
Press to select
the desired ‘USER’,
and then press
ENTER.
2
Press Cursor
button to move to
‘Setup’ and then
press ENTER button.
5
Press MENU
button to exit the
setup screen.
3
Press Cursor
button to move to
‘LOGO’ and then
press ENTER button.
• “COPY LOGO DATA” will be
displayed on the TV screen.
COPY LOGO DATA
PAUSE
3
The power will
turn off and then
back on.
SETUP
• The selected wallpaper will be
displayed.
• You can select up to 3 wallpaper
settings.
Press RETURN button to return to the previous level.
Press MENU button to exit the setup screen.
Select this to set the
Samsung Logo image as
your wallpaper.
49
Select this to set the desired
image as your wallpaper.
50
DVD Audio Disc Playback Mode
Some DVD-Audio discs contain DVD-Video as well as DVD-Audio.
To play back the DVD-Video portion of the DVD-Audio disc, set the unit to DVD-Video mode.
1
Press the MENU
button while the
disc tray is open.
3
Press Cursor
button to move to
‘DVD TYPE’ and then
press ENTER button.
2
Press Cursor
button to move to
‘Setup’ and then
press ENTER button.
4
Press Cursor ,
button to move to
‘DVD VIDEO’ and then
press ENTER button.
Setting the Speaker Mode
ENG
Signal outputs and frequency responses from the speakers will automatically be adjusted according to your
speaker configuration and whether certain speakers are used or not.
1
3
In Stop mode,
press MENU
button.
In the Speaker
Setup, press the
ENTER button again.
• Set steps 1 ~ 4 again if you want to
2
Press Cursor
button to move to
‘Audio’ and then
press ENTER button.
4
Press Cursor , ,
, buttons to move
to the desired
speaker and then
press ENTER button.
• For C, SL, and SR, each time the button
switch to DVD AUDIO Play mode.
SETUP
•
is pressed, the mode switches
alternately as follows: SMALL ➝ NONE.
For L and R, the mode is set to SMALL.
When Selecting DVD Play Mode:
• DVD VIDEO : set to play the DVD video
Note
• DVD Play mode is set to DVD Audio
as factory default setting.
•
contents contained on a
DVD audio disc.
DVD AUDIO : set to play the default
DVD audio.
SMALL : Select this when using the speakers.
NONE : Select this when no speakers are connected.
DivX (R) registration
Note
• Please use the Registration code to register this player
51
with the DivX (R) video on demand format. To learn more,
go to www.divx.com/vod.
• Depending on PRO LOGIC and STEREO settings, the speaker mode may vary (see page 61).
52
Setting the Delay Time
ENG
If the speakers cannot be placed at equal distances from the listening position, you can adjust the delay time of
the audio signals from the center and rear speakers.
1
In Stop mode,
press MENU
button.
2
Press Cursor button
to move to ‘Audio’ and
then press ENTER
button.
3
Press Cursor button
to move to ‘DELAY
TIME’ and then press
ENTER button.
4
Press Cursor , ,
, buttons to move
to the desired speaker
and then press
ENTER button.
5
Press Cursor ,
to set the Delay
time.
• You can set the delay time for C
between 00 and 05mSEC and for
SL and SR between 00 and
15mSEC.
SETUP
Setting up the Speaker Delay Time
When 5.1CH Surround Sound is played, you can enjoy the best sound if
the distance between you and each speaker is the same. Since the sounds
arrive at the listening position at different times depending on the
placement of speakers, you can adjust this difference by adding a delay
effect to the sound of the Center Speaker and Surround Speakers.
Note
(Dolby Pro Logic II), the delay time may be different for each mode.
• With
• With AC-3 and DTS, the delay time can be set between 00 and 15mSEC.
• The Center channel is only adjustable on 5.1 channel discs.
53
• Setting CENTER SPEAKER
If the distance of Dc is equal to or longer than the
distance of Df in the figure, set the mode as 0ms.
Otherwise, change the setting according to the table.
Distance between Df and Dc
0 inch
13.6 inches
27.2 inches
40.8 inches
4.5 feet
5.6 feet
Delay Time
0 ms
1 ms
2 ms
3 ms
4 ms
5 ms
• Setting REAR (SURROUND) SPEAKERS
If the distance of Df is equal to the distance of Ds
in the figure, set the mode as 0ms. Otherwise,
change the setting according to the table.
Distance between Df and Ds
0 inch
40.8 inches
6.7 feet
10.0 feet
13.4 feet
16.7 feet
Ideal CENTER
SPEAKER placement
Delay Time
0 ms
3 ms
6 ms
9 ms
12 ms
15 ms
Ideal
SURROUND
SPEAKER
placement
It is desirable to place all speakers within this circle.
Df: The distance from FRONT SPEAKER
Dc: The distance from CENTER SPEAKER
Ds: The distance from SURROUND SPEAKER
54
Setting the Test Tone
Setting the DRC (Dynamic Range Compression)
Use the Test Tone feature to check the speaker connections.
1
In Stop or no
disc mode,
press MENU
button.
2
ENG
You can use this function to enjoy Dolby Digital sound when watching movies at low volume at night.
Press Cursor
button to move to
‘Audio’ and then
press ENTER button.
3
Press Cursor button
to move to ‘TEST
TONE’ and then press
ENTER button.
1
In Stop or no disc
mode, press
MENU button.
2
3
Press Cursor
button to move to
‘DRC’ and then
press ENTER
button.
4
Press Cursor
button to move to
‘Audio’ and then
press ENTER
button.
• The test tone will be sent to L ➝ C ➝
R ➝ SR ➝ SL ➝ SW in order.
If the ENTER button is pressed again
at this time, the test tone will stop.
Press RETURN button to return to the previous level.
• When the Cursor
button is pressed,
the effect is greater, and when the
Cursor button is pressed, the effect is
smaller.
Alternate method: press the TEST TONE button on the remote.
Press TEST TONE button.
• Test tone will be produced as follows:
When playing a DVD or CD, this will work only in Stop mode.
• Use this function to check that each speaker is correctly
L: Front Speaker (L)
R: Front Speaker (R)
C: Center Speaker
SL: Rear Speaker (L)
SW: Subwoofer
SR: Rear Speaker (R)
Multi-Channel Pro Logic Mode
connected and that there is no problem.
• When there is no input signal from the HDMI IN function, the
Test Tone will not work.
To end the test tone,
press TEST TONE button again.
Start
Press RETURN button to return to the previous level.
Press MENU button to exit the setup screen.
55
56
SETUP
Press MENU button to exit the setup screen.
Press Cursor
, to adjust
the ‘DRC’.
Setting the Audio
ENG
You can adjust the balance and level for each speaker.
Method 1
1
When adjusting the audio quality using the setup screen
In Stop mode,
press MENU
button.
2
Press Cursor
button to move to
‘Audio’ and then press
ENTER button.
When manually adjusting with the SOUND EDIT button
Method 2
Adjusting Front Speaker Balance
1
TITLE
Press SOUND
EDIT button and
then press Cursor
, .
CHAP PRGM RDS RT
ST
TUNED
Adjusting Rear Speaker Balance
Adjusting Center Speaker Level
Press SOUND
EDIT button and
then press Cursor
, .
Press SOUND
EDIT button and
then press Cursor
, .
2
TITLE
CHAP PRGM RDS RT
ST
3
4
Press Cursor ,
buttons to select and
adjust the desired item.
Press the , buttons
to adjust the settings.
Adjusting Rear Speaker Level
TITLE
CHAP PRGM RDS RT
ST
TUNED
TITLE
CHAP PRGM RDS RT
ST
TUNED
kHz
MHz
Adjusting Subwoofer Speaker Level
5
TITLE
Press SOUND
EDIT button and
then press Cursor
, .
CHAP PRGM RDS RT
kHz
MHz
ST
SETUP
4
Press SOUND
EDIT button and
then press Cursor
, .
TUNED
kHz
MHz
kHz
MHz
Press Cursor button
to move to ‘SOUND
EDIT’ and then press
ENTER button.
3
TUNED
kHz
MHz
Note
Press RETURN button to return to the previous level.
Press MENU button to exit the setup screen.
57
• The adjustments will appear on the main unit's display, not on your TV screen.
Adjusting Front/Rear Speaker Balance
• You can select between 00 and –06 and OFF.
• The volume decreases as you move closer to –6.
Adjusting Center/Rear/Subwoofer Speaker Level
• The volume level can be adjusted in steps from +6dB to –6dB.
• The sound gets louder as you move closer to +6dB and quieter as you get closer to -6dB.
58
AV SYNC Setup
Sound Field (DSP)/EQ Function
Video may look slower than the audio if it is connected to a digital TV.
If this occurs, adjust the audio delay time to to match the video.
1
Press the MENU button.
• Setup menu appears.
3
Press Cursor , buttons
to move to ‘AV-SYNC’ and
then press ENTER button.
• 'Audio' menu appears.
4
DSP(Digital Signal Processor) DSP modes have been designed to simulate different acoustic environments.
EQ: You can select ROCK, POP, or CLASSIC to optimize the sound for the genre of music you are playing
Press DSP/EQ button.
• "DSP" appears on the display panel.
• Each time the button is pressed, the selection changes as follows:
Press Cursor , buttons
to select the AV-SYNC Delay
Time and then press the
ENTER button.
SETUP
• AV-SYNC screen appears.
2
Press Cursor , buttons
to move to ‘Audio’ and then
press ENTER button.
• You can set the audio delay time between 0 ms
and 300 ms. Set it to the optimal status.
Note
• DSP/EQ function is only available in STEREO mode.
Press the
PL II mode button to show STEREO on the display.
• This feature works with CDs, MP3-CDs, 2 channel DVD-Audio,
DivX and Dolby Digital discs.
• When playing a DVD disc encoded with two or more channels,
multi-channel mode will be selected automatically and DSP/EQ
function does not work.
Press RETURN button to return to the previous level.
Press MENU button to exit the setup screen.
59
ENG
POP, JAZZ, ROCK: Depending on the genre of music, you can select POP, JAZZ, and ROCK.
STUDIO : Provides a sense of presence as if in a studio.
CLUB : Simulates the sound of a dance club with a throbbing bass beat.
HALL : Provides a clear vocal as if listening in a concert hall.
MOVIE: Provides the feeling of a movie theater.
CHURCH: Gives the feel of being in a grand church.
PASS: Select this for normal listening.
60
Dolby Pro Logic II Mode
You can select the desired Dolby Pro Logic II audio mode.
Press
PL II MODE button.
• Each time the button is pressed, the mode changes as follows.
Dolby Pro Logic II Effect
ENG
This function works only in Dolby Pro Logic MUSIC mode.
1
Press
PL II MODE
button to select ‘MUSIC’
mode.
2
Press
PL II EFFECT button
to select Panorama, then press
Cursor , buttons to select
the desired effect setting.
• You can select either 0 or 1.
• This mode extends the front stereo image to
include the surround speakers for an exciting
"wraparound" effect with side wall imaging.
3
Press
PL II EFFECT button
to select C-Width, then press
Cursor , buttons to select
the desired effect setting.
4
• You can select between 0 and 7.
• This sets the width of the center image.
• You can select between 0 and 6.
• Incrementally adjusts the sound field (DSP)from
• When selecting Pro Logic II mode, connect your external device to the
AUDIO INPUT jacks (L and R) on the player. If you connect to only one of
the inputs (L or R), you cannot listen to surround sound.
Note
the front or rear.
SETUP
The higher the setting, the less sound comes from
the center speaker.
Note
Press
PL II EFFECT button
to select Dimension, then press
the Cursor , buttons to
select the desired setting.
• When playing a DVD disc encoded with two or more channels, multi-channel mode will be
selected automatically and
(Dolby Pro Logic II) button does not work.
PRO LOGIC II
• MUSIC: When listening to music, you can experience sound effects as if you are listening to the actual performance.
• CINEMA: Adds realism to the movie soundtrack.
• PRO LOGIC: You will experience a realistic multi-channel effect, as if using five speakers, while using just the front left
and right speakers.
MATRIX:
You
will hear 5.1 channel surround sound.
•
STEREO: Select this to listen to sound from the front left and right speakers and the subwoofer only.
61
62
Listening to Radio
Presetting Stations
You can listen to the chosen band (FM, AM broadcast stations) by using either the automatic or
manual tuning operation.
ENG
You can store up to:
15 FM stations
15 AM stations
• FM
• AM
Frequency Modulation
Medium Wave
Remote Control Unit
Example: Presetting FM 89.1 in the memory
1
2
Press TUNER
button.
• The selection toggles back and
Tune in to the
desired station.
Automatic Tuning 1
forth between "FM ➝ AM" each
time the FM button is pressed.
Automatic Tuning 2
Manual Tuning
When
is pressed, a
preset broadcast station is
selected.
Press and hold TUNING/CH to
automatically search for active
broadcasting stations.
1
Press the TUNER
button and select the
FM band.
• Each time the button is pressed,
the band switches between
"FM ➝ AM".
2
Press TUNING/CH
to select "89.10".
3
• Refer to Step 2 on page 63 to
Press the TUNER
MEMORY button.
• “PRGM” flashes in the display.
automatically or manually tune in
to a station.
Briefly press TUNING/CH to
increase or decrease the
frequency incrementally.
Main Unit
1
Press the Function
button to select the
desired band (FM,
AM).
2
Select a broadcast
station.
Press the STOP ( )
button to select
PRESET and then press
button to select the preset station.
Automatic Tuning 1
• You can select between 1 and
15.
5
Press the TUNER
MEMORY button
again.
6
To preset another
station, repeat
steps 2 to 5.
• Press the TUNER MEMORY button before
‘PRGM’ disappears from the display.
• ‘PRGM’ disappears from the display and
RADIO OPERATION
Press the STOP ( ) button
to select "MANUAL" and
then press and hold
button to
automatically search the band.
Automatic Tuning 2
4
Press
to select preset
number.
the station is stored in memory.
STOP ( ) to select
Manual Tuning Press
MANUAL and then briefly
press
to tune in to a lower or
higher frequency.
Press MO/ST button to listen in Mono/Stereo.
(This applies only when listening to an FM station.)
63
• Each time the button is pressed, the sound switches between "STEREO" and "MONO".
• In a poor reception area, select MONO for a clear, interference-free broadcast.
To tune in to a preset station, press
remote control to select a channel.
on the
64
Convenient Functions
ENG
Sleep Timer Function
You can set the time that the Home Theater will shut itself off.
Press SLEEP button.
time changes as follows: 10 ➝ 20 ➝ 30 ➝ 60 ➝ 90 ➝ 120 ➝ 150 ➝ OFF.
CHAP PRGM RDS RT
ST
This is useful when answering a doorbell or telephone call.
Press MUTE button.
• "SLEEP" will be displayed. Each time the button is pressed, the preset
TITLE
Mute Function
TUNED
• ‘MUTE ON’ appears in the display.
• To restore the sound, press the button again to
select ‘MUTE OFF’.
kHz
MHz
TITLE
CHAP PRGM RDS RT
ST
TUNED
kHz
MHz
To confirm the sleep timer setting, press SLEEP button.
•The remaining time before the Home Theater will shut itself off is displayed.
•Pressing the button again changes the sleep time from what you have set earlier.
To cancel the sleep timer, press SLEEP button until
OFF appears on the display.
Using Headphones
Use headphones (not supplied) for private listening pleasure.
Connect the headphones to the PHONES jack for private listening.
Adjusting Display Brightness
You can adjust the brightness of the display on the main unit so it won't interfere
with your movie viewing.
Press DIMMER button.
DARK ➞ BRIGHT.
MISCELLANEOUS
• Each time the button is pressed, the brightness changes as follows:
Caution
• To prevent hearing damage, do not increase the
volume excessively when using headphones.
65
66
Operating a TV with the Remote Control
ENG
When operating a TV with the remote control
TV Brand Code List
1
2
3
4
Press the MODE button to make the TV
indicator on the remote control flash.
TV
DVD RECEIVER
Press POWER button to turn on the TV.
Point the remote control toward the TV.
While holding down POWER, enter the code
corresponding to your brand of TV.
• If the code matches the TV's code, the TV will be turned off.
• If there is more than one code listed for your TV in the table,
enter one at a time to determine which code works.
Example: For a Samsung TV
While holding down POWER, use the number buttons to enter 00,
01, 02, 03, 04, and 05.
5
Point the remote control toward the TV and
press POWER. If the TV turns off or on,
the setting is complete.
Brand
1
SAMSUNG
No.
Brand
Code
00(Initial Value), 01, 02, 03, 04, 05, 73
30
BRANDT
2
ANAM
41
06~11, 59
31
FERGUSON
41
3
4
DAEWOO
12~18, 20, 21
32
PIONEER
41, 48, 74
LG
05, 20, 21, 22, 53
33
TELEAVA
41
5
HITACHI
23, 40, 41, 49
34
FINLUX
05, 42, 47
6
JVC
24, 55
35
FISHER
31
7
SHARP
27, 33, 34, 35, 54
36
AKAI
31
8
SONY
27, 36
37
YOKO
05
9
TOSHIBA
27, 37, 42, 43, 44, 46
38
PHONOLA
05, 45, 47
10
SANYO
27, 30, 31, 32
39
RADIOLA
05, 45
11
MITSUBISHI
05, 27, 28
40
SCHNEIDER
05
12
MATSUSHITA
09, 26
41
NEWSAN
58
13
TELEFUNKEN
41, 49, 51, 57
42
CONTINENTAL EDISON
49
Code
14
RCA
29, 61
43
SALORA
48
15
PANASONIC
07, 09, 26, 48, 49, 50
44
SELECO
48
16
SABA
40, 41, 47, 48, 49
45
NOKIA
48
17
PHILIPS
05, 45, 47, 64, 65, 66, 67, 68, 69
46
REX
48
18
GRUNDIG
39, 42, 46, 70, 71, 72
47
MIVAR
46
19
ZENITH
38
48
IMPERIAL
46
20
MIVAL
52
49
CGE
46
21
NOBLEX
56
50
BANG & OLUFSEN
47
22
EMERSON
19
51
BRIONVEGA
47
23
MAGNAVOX
25
52
FORMENTI
47
24
LOEWE
05, 60
53
METZ
47
25
THOMSON
40, 41, 49, 62, 63
54
WEGA
47
26
NORDMENDE
40, 41, 49
55
RADIOMARELLI
47
27
LOEWE OPTA
36, 47, 05
56
SINGER
47
28
BLAUPUNKT
39
57
SINUDYNE
47
29
SIEMENS
39
MISCELLANEOUS
•
You can use the TV POWER, VOLUME, CHANNEL, and Numeric
buttons (0~9).
No.
Note
• The remote control may not work on some brands of TVs. Also, some operations may not be
possible depending on your brand of TV.
• If you do not set the remote control with the code for your brand of TV, the remote control will
67
work on a Samsung TV by default.
68
Before Calling for Service
ENG
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or
if the instruction below does not help, turn off the unit, disconnect the power cord, and contact the nearest authorized dealer
or Samsung Electronics Service Center.
Symptom
Disc tray does not open.
Playback does not start.
Check/Remedy
• Is the power cord plugged securely into the outlet?
• Turn off the power and then turn it back on.
• Check the region number of the DVD.
DVD discs purchased from abroad may not be playable.
• CD-ROMs and DVD-ROMs cannot be played on this Home
Theater.
• Make sure that the rating level is correct.
Playback does not start
• Are you using a deformed disc or a disc with scratches on
the surface?
immediately when the
• Wipe the disc clean.
Play/Pause button is pressed.
Sound is not produced.
• No sound is heard during fast playback, slow playback, and step
motion playback.
• Are the speakers connected properly? Is the speaker setup
•
Sound can be heard only
from a few speakers and
not all six.
correctly customized?
Is the disc severely damaged?
• When listening to a CD or radio, sound is output to the front
•
•
speakers (L/R) only. Select "PRO LOGIC II" by pressing
(Dolby Pro Logic II) on the remote control to use all six speakers.
Make sure that the DVD disc is 5.1-CH compatible.
If you set C, SL, and SR to NONE in the speaker mode in the
audio setup of the setup screen, no sound is heard from the
center speaker and the front left and right speakers. Set C, SL,
and SR to SMALL.
Picture does not appear, sound • Was the Home Theater suddenly moved from a cold place to a
one? When condensation forms inside the player, remove the
is not produced, or the disc tray warm
disc and let the player stand for 1 or 2 hours with the power on.
opens 2 to 5 seconds later.
(You can use the player again after condensation disappears.)
69
• Is there "Dolby Digital 5.1 CH" mark on the disc? Dolby Digital 5.1
•
CH Surround Sound is produced only if the disc is recorded with
5.1 channel sound.
Is the audio language correctly set to DOLBY DIGITAL 5.1-CH in
the information display?
• Disc is rotating but no
picture is produced.
• Picture quality is poor and
picture is shaking.
Check/Remedy
• Is the TV power on?
• Are the video cables connected properly?
• Is the disc dirty or damaged?
• A poorly manufactured disc may not be playable.
The remote control does not • Is the remote control being operated within its operation range of
angle and distance?
work.
• Are the batteries exhausted?
Audio language and
subtitles do not work.
• Audio language and subtitles will not work for DVDs not containing
Menu screen does not appear even
when the menu function is selected.
• Are you using a disc that does not contain menus?
them. And depending on the disc, they may work differently.
Aspect ratio cannot be
changed.
• You can play 16:9 DVDs in 16:9 WIDE mode, 4:3 LETTER BOX
Can't receive radio
broadcast.
• The main unit is not working.
• Is the antenna connected properly?
• If the antenna's input signal is weak, install an external FM
(Example: The power goes out or
strange noise is heard.)
• The Home Theater is not
working normally.
mode, or 4:3 PAN SCAN mode, but 4:3 DVDs can be seen in 4:3
ratio only. Refer to the DVD disc jacket and then select the
appropriate function.
antenna in an area with good reception.
• Turn off the power and hold the
button on the main unit for
longer than 5 seconds.
Using the RESET function will erase all stored settings.
Do not use this unless necessary.
• While “NO DISC” message appears on the display of main unit, hold
The password for rating
level has been forgotten.
the main unit's
button for longer than 5 seconds. “INITIALIZE”
appears on the display and all settings will return to the default values.
• Press the POWER button.
Using the RESET function will erase all stored settings.
Do not use this unless necessary.
70
MISCELLANEOUS
Dolby Digital 5.1 CH
Surround Sound is not
produced.
Symptom
Cautions on Handling and Storing Discs
Small scratches on the disc may reduce sound and picture quality or cause skipping.
Be especially careful not to scratch discs when handling them.
Handling discs
Do not touch the playback side of the disc. Hold
the disc by the edges so that fingerprints will not
get on the surface.
Do not stick paper or tape on the disc.
Disc Storage
Keep in a cool
ventilated area
Do not keep in
direct sunlight
Caution
Keep in a clean
Protection jacket.
Store vertically.
• Do not allow the discs to become contaminated with dirt.
• Do not load cracked or scratched discs.
Language Code List
ENG
Enter the appropriate code number for the initial settings “Disc Audio”, “Disc Subtitle”
and/or “Disc Menu” (See page 43).
Code
Language
Code
Language
Code
Language
Code
Language
1027
Afar
1181
Frisian
1334
Latvian, Lettish
1506
Slovenian
1028
Abkhazian
1183
Irish
1345
Malagasy
1507
Samoan
1032
Afrikaans
1186
Scots Gaelic
1347
Maori
1508
Shona
1039
Amharic
1194
Galician
1349
Macedonian
1509
Somali
1044
Arabic
1196
Guarani
1350
Malayalam
1511
Albanian
1045
Assamese
1203
Gujarati
1352
Mongolian
1512
Serbian
1051
Aymara
1209
Hausa
1353
Moldavian
1513
Siswati
1052
Azerbaijani
1217
Hindi
1356
Marathi
1514
Sesotho
1053
Bashkir
1226
Croatian
1357
Malay
1515
Sundanese
1057
Byelorussian
1229
Hungarian
1358
Maltese
1516
Swedish
1059
Bulgarian
1233
Armenian
1363
Burmese
1517
Swahili
1060
Bihari
1235
Interlingua
1365
Nauru
1521
Tamil
1069
Bislama
1239
Interlingue
1369
Nepali
1525
Tegulu
1066
Bengali; Bangla
1245
Inupiak
1376
Dutch
1527
Tajik
1067
Tibetan
1248
Indonesian
1379
Norwegian
1528
Thai
1070
Breton
1253
Icelandic
1393
Occitan
1529
Tigrinya
1079
Catalan
1254
Italian
1403
(Afan) Oromo
1531
Turkmen
1093
Corsican
1257
Hebrew
1408
Oriya
1532
Tagalog
1097
Czech
1261
Japanese
1417
Punjabi
1534
Setswana
1103
Welsh
1269
Yiddish
1428
Polish
1535
Tonga
1105
Danish
1283
Javanese
1435
Pashto, Pushto
1538
Turkish
1109
German
1287
Georgian
1436
Portuguese
1539
Tsonga
1130
Bhutani
1297
Kazakh
1463
Quechua
1540
Tatar
Greek
1298
Greenlandic
1481
Rhaeto-Romance
1543
Twi
1144
English
1299
Cambodian
1482
Kirundi
1557
Ukrainian
1145
Esperanto
1300
Kannada
1483
Romanian
1564
Urdu
When you get fingerprints or dirt on the disc, clean it
with a mild detergent diluted in water and wipe with a
soft cloth.
1149
Spanish
1301
Korean
1489
Russian
1572
Uzbek
1150
Estonian
1305
Kashmiri
1491
Kinyarwanda
1581
Vietnamese
1151
Basque
1307
Kurdish
1495
Sanskrit
1587
Volapuk
• When cleaning, wipe gently from the inside to the outside of the disc.
1157
Persian
1311
Kirghiz
1498
Sindhi
1613
Wolof
1165
Finnish
1313
Latin
1501
Sangro
1632
Xhosa
Handling and Storing Discs
Note
• Condensation may form if warm air comes into contact with cold parts
1166
Fiji
1326
Lingala
1502
Serbo-Croatian
1665
Yoruba
1171
Faeroese
1327
Laothian
1503
Singhalese
1684
Chinese
1174
French
1332
Lithuanian
1505
Slovak
1697
Zulu
inside the player. When condensation forms inside the player, the player
may not operate correctly. If this occurs, remove the disc and let the
player stand for 1 or 2 hours with the power on.
71
72
MISCELLANEOUS
1142
Specifications
SAMSUNG Home Theater
ENG
LIMITED WARRANTY TO ORIGINAL PURCHASER
G
E
N
E
R
A
L
F
M
A
M
V
I
D
E
O
T
U
N
E
R
T
U
N
E
R
O
U
T
P
U
T
A
M
P
L
I
F
I
E
R
Power Consumption
Weight
Dimensions (W x H x D)
Operating Temperature Range
Operating Humidity Range
Usable Sensitivity
S/N Ratio
Distortion
Usable Sensitivity
S/N Ratio
Distortion
Composite Video
S-VIDEO
Component Video
HDMI
Front speaker output
Center speaker output
Rear speaker output
Subwoofer speaker output
Frequency range
S/N Ratio
Channel separation
Input sensitivity
Speaker system
Impedance
Frequency range
Output sound pressure level
Rated input
Maximum input
Dimensions (W x H x D)
Weights
This SAMSUNG brand product, as supplied and distributed by Samsung Electronics America, Inc. (SAMSUNG) and delivered new, in the original
carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited
warranty period of:
One (1) Year Parts and Labor*
(*90 Days Parts and Labor for Commercial Use)
This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United States. To receive
warranty service, the purchaser must contact SAMSUNG for problem determination and service procedures. Warranty service can only be
performed by a SAMSUNG authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to
SAMSUNG or SAMSUNG's authorized service center. Transportation of the product to and from the service center is the responsibility of the
purchaser.
SAMSUNG will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if
found to be defective during the limited warranty period specified above. All replaced parts and products become the property of SAMSUNG and
must be returned to SAMSUNG. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is
longer.
SAMSUNG’s obligations with respect to software products distributed by SAMSUNG under the SAMSUNG brand name are set forth in the
applicable end user license agreement. Non-SAMSUNG hardware and software products, if provided, are on an “AS IS” basis. Non-SAMSUNG
manufacturers, suppliers, publishers, and service providers may provide their own warranties.
This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, and except to the extent otherwise
expressly provided for in this statement, noncommercial use of this product, and shall not apply to the following, including, but not limited to:
damage which occurs in shipment; delivery and installation; applications and uses for which this product was not intended; altered product or
serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire, water, lightning or other acts of nature; use of products,
equipment, systems, utilities, services, parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not supplied
and authorized by SAMSUNG, or which damage this product or result in service problems; incorrect electrical line voltage, fluctuations and surges;
customer adjustments and failure to follow operating instructions, cleaning, maintenance and environmental instructions that are covered and
prescribed in the instruction book; product removal or reinstallation; reception problems and distortion related to noise, echo, interference or other
signal transmission and delivery problems. SAMSUNG does not warrant uninterrupted or error-free operation of the product.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES WHETHER
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED ABOVE, AND NO OTHER EXPRESS
WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING
ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER
BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO
USE THIS PRODUCT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN
AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT
LIMITING THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND
PURCHASER’S PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE THIS
PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED WARRANTY SHALL NOT
EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR
EXCLUSIVE REMEDY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages,
so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
To obtain warranty hardware service, please contact SAMSUNG at:
73
SAMSUNG CUSTOMER CARE CENTER
400 Valley Road, Suite 201, Mt. Arlington, NJ 07856
1-800-SAMSUNG (1-800-726-7864) and www.samsung.com
74
MISCELLANEOUS
S
P
E
A
K
E
R
140W
13.5Ibs
17 x 3.4 x 16 inches
41°F ~ 95°F
10% ~ 75%
10dB
60dB
0.5%
54dB
40dB
2%
1.0Vp-p(75Ω load)
Luminance Signal: 1.0Vp-p(75Ω load)
Color Signal: 0.286Vp-p(75Ω load)
Y:1.0Vp-p(75Ω load)
Pr:0.70Vp-p(75Ω load)
Pb:0.70Vp-p(75Ω load)
Impedance: 85~115Ω
134W x 2(3Ω)
134W(3Ω)
134W x 2(3Ω)
130W(3Ω)
20Hz~20KHz
75dB
50dB
(AUX)400mV
5.1ch speaker system
Front/Center/Rear speaker
Subwoofer speaker
3Ω x 5
3Ω
130Hz~20KHz/125Hz~20KHz
40Hz~250Hz
84dB/W/M
86dB/W/M
134W
130W
268W
260W
Front/Rear 4.0 x 9.5 x 5.2 inches
7.9 x 15.9 x 14.2 inches
Center
13.7 x 4.0 x 5.1 inches
Front/Rear 1.7 Ibs
13.4 Ibs
Center
2.2 Ibs