User manual | Siemens Hicom 300 E CS Rel 6.5 PBX with CallManager using

Add to my manuals
34 Pages

advertisement

User manual | Siemens Hicom 300 E CS Rel 6.5 PBX with CallManager using | Manualzz

Application Note

Siemens Hicom 300 E CS Rel 6.5 PBX with CallManager using

2621-T1 PRI NI-2 Gateway

This application note illustrates for connectivity of the Siemens Hicom 330 E Rel 3.1

PBX with Cisco CallManager using Cisco 2621-T1 PRI NI1 Gateway.

Integration Description

Connectivity is achieved by using the industry standard PRI NI-2 protocol. The

Siemens Hicom 300 E CS can be configured as either NETWORK or USER side.

Cisco Systems Hardware and

Software Requirements

• Hardware (Cisco 2621Gateway):

2MFT T1 Port

• Software: CallManager Release 3.1

PBX Hardware and Software

Requirements

• Hardware: TMDN or TMDN 64

• Software: Version 6.5

Features Supported

• When calling from Cisco 7960 IP phone to Siemens digital phone, Calling/Called

Number is displayed on both phones after the call is answered.

• When calling from Siemens digital phone to Cisco 7960 IP phone, IP phone displays Connected Number after the call is answered. Siemens phone however does NOT get updated when the call is answered. It displays the dialed numbers instead. (i.e. Access

Code + extension number). It was verified using ISDN protocol analyzer that the CallManager was not sending

"Connected Number” information in the connect message back to PBX.

• When a call is answered, the display on the Siemens phone is only active

(Calling Number displayed) for approximately 4 seconds. Thereafter, the screen goes blank. This could be caused by a timer feature that is expiring for the display.

Key Features Supported

Calling/Called Number

Key Features Not Supported

Calling/Called Name

Limitations

User/Network Settings

The Cisco 2621 router with ISDN switch type setting of primary-ni supports both protocol sides by using the “isdn protocol-emulate network/user” command.

When the router is set to emulate Network side and the Siemens is set to emulate User

Calling Name and Number feature

• Calling Name delivery and presentation features are not supported by the

Siemens Hicom 330 E CS PBX.

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 1 of 34

side, the Siemens PBX must send at least 10 digits for the router to properly route the call. Otherwise, the Cisco 2621 router sends back a release message containing a release cause of “Invalid Number Format”.

Network Topology

Figure 1 Basic Setup

Configuration

Configuringthe Siemens Hicom 300 E CS PBX

Use the following steps to configure the Siemens Hicom 300 E CS PBX:

Step 1.

Add the new access code to DPLN.

Step 2.

Add the new trunk board using BCSU.

Step 3.

Configure COT.

Step 4.

Configure COP.

Step 5.

Add the new trunk group access code using TGACC.

Step 6.

Add the channels using TCSU.

Step 7.

Configure LROUT.

Step 8.

Configure LODR.

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 2 of 34

Siemens Hicom 330 E CS PBX Configuration Menus and Commands

Step 1.

Add the new access code to DPLN.

<dis-dpln

TYPE = dgts

DGTS = ;

DIS-DPLN:DGTS,;

H500: AMO DPLN STARTED

--------------------------------------------------------------------------

| DIGIT INTERPRETATION VALID FOR DIAL PLAN 0 |

--------------------------------------------------------------------------

| | CALL PROGRESS STATE | DIGIT ANALYSIS| | |

| DIRECTORY NUMBER| 1 11111 1111222| RESULT |RSVD | ROUTE|

| |12345 67890 12345 6789012| (SKIP DIGIT) | | |

--------------------------------------------------------------------------

| 0 |....* ..... ..... .......| GENANS | | |

| 1 |.*.** *.*** **... ......*| CO | | |

| 2000 - 2002 |.**** ***** ***.* ......*| STN | | |

| 2003 - 2024 |.**** ***** ***.* ......*| STN | R | |

| 2025 - 2026 |.**** ***** ***.* ......*| STN | | |

| 2027 - 2099 |.**** ***** ***.* ......*| STN | R | |

| 37 - 41 |.*.** *.*** **... ......*| CO | | |

| 43 - 48 |.**** ***** **... ......*| TIE | | |

| 49 - 50 |.*.** *.*** **... ......*| CO | | |

| 70000 - 70999 |.**** ***** ***.* ......*| STN | R | |

| 71000 |.**** ***** ***.* ......*| STN | | 1 |

| 71001 - 79998 |.**** ***** ***.* ......*| STN | R | |

--------------------------------------------------------------------------

| DIGIT INTERPRETATION VALID FOR DIAL PLAN 0 |

--------------------------------------------------------------------------

| | CALL PROGRESS STATE | DIGIT ANALYSIS| | |

| DIRECTORY NUMBER| 1 11111 1111222| RESULT |RSVD | ROUTE|

| |12345 67890 12345 6789012| (SKIP DIGIT) | | |

--------------------------------------------------------------------------

| 79999 |.**** ***** ***.* ......*| STN | | |

| 9 |.*.** *.*** **... ......*| CO | | |

| *0 |*...* ..**. ..... ......*| ACDWORK | | |

| *2 |*...* ..**. ..... ......*| ACCTCODE | | |

| *3 |....* ..**. ..... ......*| PUDIR | | |

| *4 |*...* ..**. ..... ......*| CONFRNC | | |

| *52 |....* ..... ..... .......| MWCAN | | |

| *530 |....* ..... ..... ......*| PMCANCEL | | |

| *532 |....* ..... ..... ......*| PMCALLBK | | |

| *563 |*.... ..**. ..... .......| BADLINE | | |

| *564 |*...* ..**. ..... ......*| ACDLOGON | | |

| *565 |*...* ..**. ..... ......*| ACDLOGOF | | |

--------------------------------------------------------------------------

| DIGIT INTERPRETATION VALID FOR DIAL PLAN 0 |

--------------------------------------------------------------------------

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 3 of 34

| | CALL PROGRESS STATE | DIGIT ANALYSIS| | |

| DIRECTORY NUMBER| 1 11111 1111222| RESULT |RSVD | ROUTE|

| |12345 67890 12345 6789012| (SKIP DIGIT) | | |

--------------------------------------------------------------------------

| *570 |*...* ..**. ..... .......| ACDPQ | | |

| *571 |*...* ..**. ..... .......| ACDPS | | |

| *572 |....* ..... ..... .......| RING | | |

| *580 |*...* ..**. ..... .......| ACDSQ | | |

| *581 |*...* ..**. ..... .......| ACDSS | | |

| *6 |***** ..**. ..... .......| ROLMPARK | | |

| *7 |*...* ..**. ..... .......| CONSULT | | |

| *80 - *89 |.**** ..**. ..... .......| PARK | | |

| *9 |....* ..**. ..... .......| HOLD | | |

| **0 |.***. ..... ..... .......| BVSL | | |

| **1 |*.... ..**. ..... ......*| TOGGLE | | |

| **3 |....* ..**. ..... ......*| PU | | |

--------------------------------------------------------------------------

| DIGIT INTERPRETATION VALID FOR DIAL PLAN 0 |

--------------------------------------------------------------------------

| | CALL PROGRESS STATE | DIGIT ANALYSIS| | |

| DIRECTORY NUMBER| 1 11111 1111222| RESULT |RSVD | ROUTE|

| |12345 67890 12345 6789012| (SKIP DIGIT) | | |

--------------------------------------------------------------------------

| **41 - **48 |..... ..*.. ..... ......*| CONFRMV | | |

| **50 |*...* ..**. ..... .......| CAFGRAVL | | |

| **51 |*...* ..**. ..... .......| CAFGRUNA | | |

| **6 |....* ..**. ..... .......| INTERCOM | | |

| **8 |....* ..... ..... .......| MWANS | | |

| ***4 |..... ..... ..... ......*| CONFRMVL | | |

| ***5 |....* ..... ..... .......| MONSLNT | | |

| **#65 |*...* ..**. ..... .......| CAFGROFF | | |

| *#01 |....* ..... ..... .......| RCHNL | | |

| *#02 |....* ..... ..... .......| RTERM | | |

| *#03 |....* ..... ..... .......| LTERM | | |

| *#04 |..... *.... *.... .......| PRITEST | | |

--------------------------------------------------------------------------

| DIGIT INTERPRETATION VALID FOR DIAL PLAN 0 |

--------------------------------------------------------------------------

| | CALL PROGRESS STATE | DIGIT ANALYSIS| | |

| DIRECTORY NUMBER| 1 11111 1111222| RESULT |RSVD | ROUTE|

| |12345 67890 12345 6789012| (SKIP DIGIT) | | |

--------------------------------------------------------------------------

| *#274 |*...* ..... ..... .......| WS | | |

| *#50 |*...* ..**. ..... .......| CAFAVLB | | |

| *#51 |*...* ..**. ..... .......| CAFUNAV | | |

| *#55 |*...* ..**. ..... .......| CAFFWD | | |

| *#56 |*...* ..**. ..... .......| CAFFWDC | | |

| *#57 |....* ..... ..... .......| PIDON | | |

| *#58 |....* ..... ..... .......| PIDOFF | | |

| *#590 |....* ..... ..... .......| DCOSX | | |

| *#591 |....* ..... ..... .......| ACOSX | | |

| *#63 |***** ***** ***** *******| CLEAR | | |

| *#65 |*...* ..**. ..... .......| CAFLOGOF | | |

| *#735 |....* ..... ..... .......| RELOCATE | | |

--------------------------------------------------------------------------

| DIGIT INTERPRETATION VALID FOR DIAL PLAN 0 |

--------------------------------------------------------------------------

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 4 of 34

| | CALL PROGRESS STATE | DIGIT ANALYSIS| | |

| DIRECTORY NUMBER| 1 11111 1111222| RESULT |RSVD | ROUTE|

| |12345 67890 12345 6789012| (SKIP DIGIT) | | |

--------------------------------------------------------------------------

| *#738 |....* ..... ..... .......| SET | | |

| *#97 |..*.. *.... ..... .......| COXFER | | |

| #0 |*...* ..**. ..... ......*| ACDUNAV | | |

| #1 |*.... ..*.. ....* .......| ACBK | | |

| #2 |*...* ..**. ..... .......| PRION | | |

| #3 |.**.* ..**. ..... ......*| SPDI | | |

| #4 |***.* ..**. ....* ......*| SNR | | |

| #5 |....* ..... ..... .......| ADND | | |

| #61 |.**** ..*** **... ......*| SPDC1 | | |

| #62 |.**** ..*** **... ......*| SPDC2 | | |

| #80 |*...* ..**. ..... .......| BROADCST | | |

| #81 |*...* ..**. ..... .......| SPKRCALL | | |

--------------------------------------------------------------------------

| DIGIT INTERPRETATION VALID FOR DIAL PLAN 0 |

--------------------------------------------------------------------------

| | CALL PROGRESS STATE | DIGIT ANALYSIS| | |

| DIRECTORY NUMBER| 1 11111 1111222| RESULT |RSVD | ROUTE|

| |12345 67890 12345 6789012| (SKIP DIGIT) | | |

--------------------------------------------------------------------------

| #8378 |..... ..... ....* .......| HWTEST | | |

| #91 |....* ..... ....* .......| CFWVABTH | | |

| #92 |....* ..... ....* .......| CFWVAEXT | | |

| #93 |....* ..... ....* .......| CFWVAINT | | |

| #94 |....* ..... ....* .......| CFWVB | | |

| #95 |....* ..... ....* .......| CFWVBNA | | |

| #96 |....* ..... ....* .......| CFWVNA | | |

| #*056 |....* ..... *.... .......| DATA56 | | |

| #*1 |***** ..**. ..... .......| MWACT | | |

| #*2 |*...* ..**. ..... .......| BUZZ | | |

| #*329 |.**.* *.*** **... .......| FAX | R | |

| #*4 |*...* ..**. ..... .......| VCECALL | | |

--------------------------------------------------------------------------

| DIGIT INTERPRETATION VALID FOR DIAL PLAN 0 |

--------------------------------------------------------------------------

| | CALL PROGRESS STATE | DIGIT ANALYSIS| | |

| DIRECTORY NUMBER| 1 11111 1111222| RESULT |RSVD | ROUTE|

| |12345 67890 12345 6789012| (SKIP DIGIT) | | |

--------------------------------------------------------------------------

| #*75 |....* ..... ..... .......| DIGIDAT | | |

| #*76 |....* *.**. ..*.* .......| SWITCH | | |

| #*77 |....* *.*** ***.* .......| DTE | | |

| #*78 |....* ..**. ....* .......| CODE | | |

| #*79 |....* ..**. ....* .......| SPEED | | |

| #*8 |***** ****. ..*** *****..| MWCANORI | | |

| #*90 |....* ..... ....* .......| HUNTPROG | | |

| #*92 |....* ..... ..... .......| AHTVCE | | |

| #*93 |....* ..... ..... .......| DHTVCE | | |

| #*94 |....* ..... ..... .......| AHTDTE | | |

| #*95 |....* ..... ..... .......| DHTDTE | | |

| #*96 |....* ..... ..... .......| AHTFAX | | |

--------------------------------------------------------------------------

| DIGIT INTERPRETATION VALID FOR DIAL PLAN 0 |

--------------------------------------------------------------------------

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 5 of 34

| | CALL PROGRESS STATE | DIGIT ANALYSIS| | |

| DIRECTORY NUMBER| 1 11111 1111222| RESULT |RSVD | ROUTE|

| |12345 67890 12345 6789012| (SKIP DIGIT) | | |

--------------------------------------------------------------------------

| #*97 |....* ..... ..... .......| DHTFAX | | |

| #*99 |....* ..... ....* .......| HUNTCLR | | |

| ##0 |*...* ..**. ..... ......*| ACDAVLB | | |

| ##1 |....* ..... ..... .......| DCBK | | |

| ##2 |*...* ..**. ..... .......| PRIOFF | | |

| ##3 |....* ..... ....* .......| SPDIPROG | | |

| ##4 |*...* ..**. ..... ......*| LNR | | |

| ##5 |....* ..... ..... .......| DDND | | |

| ##7 |*.... ..... ..... .....*.| KNOVR | | |

| ##8 |***** ..**. ..... .......| DTA | | |

| ##91 |....* ..... ....* .......| CFWVAOFF | | |

| ##*78 |....* ..**. ....* .......| RESET | | |

--------------------------------------------------------------------------

| DIGIT INTERPRETATION VALID FOR DIAL PLAN 0 |

--------------------------------------------------------------------------

| | CALL PROGRESS STATE | DIGIT ANALYSIS| | |

| DIRECTORY NUMBER| 1 11111 1111222| RESULT |RSVD | ROUTE|

| |12345 67890 12345 6789012| (SKIP DIGIT) | | |

--------------------------------------------------------------------------

| ###1 |*.... ...*. ..... .......| TRACE | | |

| ###20 |..... **..* **... .......| MILLWAT | | |

| ###21 |..... **..* **... .......| LOOPBACK | | |

| ###22 |..... **..* **... .......| SILENCE | | |

| ###23 |..... **..* **... .......| COMBO | | |

| ###4 |*.... ..... ..... .......| THRCONF | | |

| ###6 |....* ..... ..... .......| MONTONE | | |

--------------------------------------------------------------------------

AMO-DPLN -135 DIALING PLANS, FEATURE ACCESS CODES

DISPLAY COMPLETED;

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 6 of 34

Step 2.

Add the new trunk board using BCSU.

<dis-bcsu

TYPE = tmd;

DIS-BCSU:TMD;

H500: AMO BCSU STARTED

---------------------------------------------------------------

| DETAILS OF TMD BOARD AT ADDRESS (LTG.LTU.SLOT) = 1. 2.103 |

| |

| CABTYP = 1 TIMTYP = SYST SIGTYP = MOS |

| FRAME = ESF TABS = NO FCTID = 2 |

| BI8SUB = YES BIVDET = NO |

|-------------------------------------------------------------|

| RDRATIO = 6 RDTH = 2500 RDQUAL = 15000 |

| YLSEND = 5000 YLTH = 400 YLQUAL = 100 |

| LOS = 150 AOS = 4000 |

| SESDISTH = 10 SESREQTH = 10 |

| OESDISTH = 30 OESDISIN = 24-00-00 |

| OESREQTH = 4 OESREQIN = 04-00-00 |

|-------------------------------------------------------------|

| NETUSR = NETWK ACKTIM = 1000 DLVTIM = 30000 |

| OCTMAX = 260 RETMAX = 3 WINDOW = 1 |

| CRIDC = TTSC = NSFIV = |

| NSFTSC = PFDGT = |

|-------------------------------------------------------------|

| IGN = 0 IID = 1 |

---------------------------------------------------------------

AMO-BCSU -135 BOARD CONFIGURATION, SWITCHING UNIT

DISPLAY COMPLETED;

Step 3.

Configure COT.

<dis-cot

COTNO = 0;

DIS-COT:0;

H500: AMO COT STARTED

|D|A|D|D|D|M|S|V|E|E|A|R|

|I|N|S|S|I|D|A|L|S|S|N|F|

|T|S|A|A|S|R|T|S|P|P|I|L|

| |R| |S| | | |A|A|D|D|A|

| | | | | | | |T|N|N|N|S|

| | | | | | | | |I|I|I|H|

COT | | | | | | | | | |S|S| |

----+-+-+-+-+-+-+-+-+-+-+-+-+

0 | | | | | | | | | | | | |

----+-+-+-+-+-+-+-+-+-+-+-+-+

AMO-COT -135 CLASS OF TRUNK FOR CALL PROCESSING

DISPLAY COMPLETED;

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 7 of 34

Step 4.

Configure Class of Parameter for device handler using COP.

<dis-cop

COPNO = 0;

DIS-COP:0;

H500: AMO COP STARTED

| | | | | |

| | S E A | | | |

| | T E S N | | | |

| | A S V S P I D |DD| S| |

| | D Z L P D D T |TT| U| P |

| | I A A S S A N N O |MM| P| D |

|COP| A N C A A N I I N |FF| V| P |

|IDX| L S K T T I S S E | L|12|1234|

+---+-------------------+--+--+----+

| 0| | | | |

+---+-------------------+--+--+----+

AMO-COP -135 CLASS OF PARAMETER

DISPLAY COMPLETED;

Step 5.

Add the new trunk group access code using TGACC.

<dis-tgacc

TGRP = 40;

DIS-TGACC:40;

H500: AMO TGACC STARTED

+------------------------------------------------------------------------------+

| TGRP NUMBER : 40 TGRP NAME : T1PRI /N MAXIMUM NO: 23 |

| SUBGROUP NUMBER: 11 DEVICE TYPE: PRI B DIR TYPE : BOTH |

| ACD THRESHOLD : * TRACENO : 0 USAGE TYPE: TERR |

| ALLOCATED TO AT LEAST ONE ROUTE GDTR RULE : 0 |

| SELECTION : LOW CFBLOCK : DISABLED |

| THE FOLLOWING PORTS (LTG-LTU-SLOT-CIRCUIT) ARE ALLOCATED: |

+------------------------------------------------------------------------------+

| 1- 2-103- 1| 1- 2-103- 2| 1- 2-103- 3| 1- 2-103- 4| 1- 2-103- 5| 1- 2-103- 6|

+------------------------------------------------------------------------------+

| 1- 2-103- 7| 1- 2-103- 8| 1- 2-103- 9| 1- 2-103-10| 1- 2-103-11| 1- 2-103-12|

+------------------------------------------------------------------------------+

| 1- 2-103-13| 1- 2-103-14| 1- 2-103-15| 1- 2-103-16| 1- 2-103-17| 1- 2-103-18|

+------------------------------------------------------------------------------+

| 1- 2-103-19| 1- 2-103-20| 1- 2-103-21| 1- 2-103-22| 1- 2-103-23| - - - |

+------------------------------------------------------------------------------+

AMO-TGACC-135 TRUNK GROUP ACCESS CODE

DISPLAY COMPLETED;

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 8 of 34

Step 6.

Add the channels using TCSU.

TCSU – B Channel

<dis-tcsu

PEN1 = 1-2-103-1;

DIS-TCSU:1-2-103-1;

H500: AMO TCSU STARTED

+------------------------------------------------------------------------+

| PEN: 1- 2-103- 1 INS: Y BOARD: TMDN64P DEV: PRIB TGRP: 40 |

+------------------------------------------------------------------------+

| TRKID : 0040 TCCID : |

| CCT : /0040 |

| |

| ACDATA : 0 DITIDX : 0 LOCANA : |

| ATNTYP : ISDN DPLN : 0 REMANA : |

| COPNO : 0 ITR : 0 SIDANI : N |

| COSNO : 75 LCRCOSD : 5 SRTIDX : 3 |

| COTNO : 0 LCRCOSV : 5 TRTBL : DIDCR |

| DEDSVC : NONE FACILITY : * |

+------------------------------------------------------------------------+

AMO-TCSU -135 TRUNK CONFIGURATION, SWITCHING UNIT

DISPLAY COMPLETED;

TCSU – D Channel

<dis-tcsu

PEN1 = 1-2-103-24;

DIS-TCSU:1-2-103-24;

H500: AMO TCSU STARTED

+------------------------------------------------------------------------+

| PEN: 1- 2-103-24 INS: Y BOARD: TMDN64P DEV: PRID |

+------------------------------------------------------------------------+

| TCCID : |

| CCT : |

| |

| ACDATA : 0 DEDSCC : INTERFID : |

| COPNO : 0 DITIDX : ITR : 0 |

| COTNO : 0 DPLN : 0 PROTOCOL : NI2 |

| |

| TMR301 : 300 SEC. TMR308 : 4 SEC. TMR313 : 4 SEC. |

| TMR303 : 4 SEC. TMR309 : 90 SEC. TMR316 : 30 SEC. |

| TMR305 : 30 SEC. TMR310 : 30 SEC. TMR322 : 4 SEC. |

| TDELAY : 3000 MSEC. BEARER: ONE |

| NCT : N TNCT : |

+------------------------------------------------------------------------+

AMO-TCSU -135 TRUNK CONFIGURATION, SWITCHING UNIT

DISPLAY COMPLETED;

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 9 of 34

Step 7.

Configure LROUT.

<dis-lrout

ROUTE = 40;

DIS-LROUT:40;

H500: AMO LROUT STARTED

LCR ROUTE DEFINITION TABLE

--------------------------

-------------------------------------------------------------------------

|ROUTENUM = 40 SCHED A = X AORT = INFORMATION |

|ROUTEELE = 1 B = AUTH = 1 TRANS CAP = S3V |

|BEARER = ONE C = ONHKQ = Y TRKSIG = PRI |

|BANDWTH = 1 D = OFFHKQ = Y SCCID = |

|TRUNKGRP = 40 E = ODRNUM = 1 SVCVCE = NON |

|MASTGRP = 8 F = APLTYP = VD SVCN-V = NON |

|ROUTSERV = N G = FACNUM = |

| H = |

-------------------------------------------------------------------------

END OF LCR ROUTE DEFINITION TABLE DISPLAY

AMO-LROUT-135 ROUTE DEFINITION DETERMINATION PACKAGE

DISPLAY COMPLETED;

Step 8.

Configure LODR.

<dis-lodr

RANGE =

DIS-LODR:;

H500: AMO LODR STARTED

<< DISPLAY LCR OUTDIAL RULE >>

ODR NO COMMAND BRANCH VALUE

------ ------- ------------

1 ECHOALL

END

--------AMO-LODR -135

DISPLAY COMPLETED;

AMO LCR ODR FOR SWITCHING UNIT

<

-------- END OF DISPLAY

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 10 of 34

Configuring the Cisco CallManager

Figure 1

Configuring the 6608-E1 Gateway

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 11 of 34

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 12 of 34

Route Pattern Configuration

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 13 of 34

Test Results

As shown in the diagram below, a Siemens Hicom 300 E CS PBX was connected via an ISDN T1 PRI link to a Cisco

2621, which in turn, was connected to an Ethernet switch. The interoperability testing involved Layers 1, 2 and 3 on the ISDN PRI link between a Cisco 2621 and the PBX.

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 14 of 34

Test Configuration

Layer 1 (Physical Layer)

The Siemens configuration screen for the DS1 trunk interface is reached with the command:

<cha-bssu

Layers 2 & 3 (Q.921 and Q.931)

Layer 2 and 3 packet exchanges were monitored using an Acacia Clarinet protocol analyzer, bridged across the PRI link in high impedance mode.

Layer 2 Q.921 packets were monitored to ensure that each PBX/2621 software configuration properly exchanged

SABME/UA packets to initialize the ISDN link, and then RR packets were exchanged every 30 seconds.

Layer 3 Q.931 packets were monitored to ensure that the appropriate call setup/teardown packets were exchanged for each configuration, and that the SETUP packets contained the mandatory Information Elements (IEs) with the necessary details, as well as optional IEs such as Calling Name and Number.

Telephone calls were made end-to-end in both directions through the Cisco 2621Gateway, and a check was made to ensure that there was an audio path in both directions for each call.

User/Network Settings

The Cisco 2621Gateway with ISDN protocol type setting of primary-ni supports both protocol sides by selecting

“Network/User” in the protocol side field when configuring the Gateway via CallManager.

The “Network/user” choice for the Siemens Hicom 300 E PBX is made by deactivating the B channels/D-channel

(<dea-dssu) and the DS1 board (<dea-bssu) consecutively. A change command is then issued to the Board

Configuration Switching Unit (BCSU) to get to the “network/user” prompt (<cha-bcsu). The DS1 board by

(<act-bssu), the D-channel, and B-channels are then reactivated (<act-dssu), after the settings are changed.

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 15 of 34

.

Table 1 PBX 1 - NI2 (Network) Cisco 2621 Gateway - primary-ni(User)

Siemens Hicom 330 E CS

Switch-type/ Protocol side setting

NI2 / Network

Cisco Cisco 2621_B ISDN protocol-type/Protocol side setting isdn switch-type primary-ni isdn protocol-emulate user

Table 2 Basic Calls: (Enbloc Sending)

Calls Made

Phone C to Phone A

Call

Comp?

Phone A to Phone C Yes

Yes

“Calling

Number”

Passed to

Final

Destination?

“Calling

Name”

Passed to

Final

Destination?

Yes No

“Called

Number”

Passed to

Orig. Side?

No

1

Yes No Yes

“Called

Name”

Passed to

Orig. Side?

No

No

Notes

2

3

1. CallManager is not sending "Connected Number" information in the connect message back to PBX.

2. The Siemens PRI interface with ETSI setting does not support “Calling Name” presentation Feature.

3. The display on the Siemens phone is oly active (Calling Number is displayed) for apporximately 4 seconds, thereafter the displays goes blank. This could be caused by a display timer feature that expires.

Table 3 Call Transfers: (Supervised Local Transfers)

Calls Made

Phone C to Phone

A Xfr to Phone B

Phone A to Phone

C Xfr to Phone D

Call

Comp?

Yes

Yes

Orig.

“Calling

Number” displayed on

Final Dest.

phone?

Yes

Orig.

“Calling

Name” displayed on

Final Dest.

phone?

No

“Called

Number” display on

Orig. phone updated after transfer?

No

Yes No No

“Called

Name” display on

Orig. phone updated after transfer?

No

Notes

No

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 16 of 34

Table 4 Call Conferencing (Local)

Calls Made

Call

Comp?

Phone C to Phone A,

Phone A conf Phone B

Yes

Phone C to Phone A,

Phone C conf Phone D

Yes

Phone A to Phone C,

Phone C conf Phone D

Yes

Phone A to Phone C,

Phone A conf Phone B

Yes

“Calling

Number”

Passed to remaining conferee when the conferencing phone drops out?

(A Drops out)

Yes

(C Drops out)

No

(C Drops out)

No

(A Drops out)

No

“Calling

Name” displayed on remaining conferee when the conferencing phone drops out?

(A Drops out)

No

(C Drops out)

No

(C Drops out)

No

(A Drops out)

No

“Connected

Number” updated on

Orig. Caller phone display when a conferee drops out?

(A Drops out)

No

(D Drops out)

No

(C Drops out)

No

(B Drops out)

No

“Connected

Name” updated on

Orig. Caller phone display when a conferee drops out?

(A Drops out)

No

(D Drops out)

No

(C Drops out)

No

(B Drops out)

No

Notes

Table 5 Call Forward (Local)

Calls Made

Phone C to Phone

A fwd to Phone B

Phone A to Phone

C fwd to Phone D

Yes

Call

Comp?

Yes

Original

“Calling

Number”

Passed to Final

Dest.?

Original

“Calling

Name”

Passed to Final

Dest.?

Yes No

Yes No No

Forwardi ng

“Called

Number”

Pased to

Final

Dest.?

Forwardi ng

“Called

Name”

Displaye d on

Final

Dest.?

No No

Final dest.

“Connec ted

Number” updated at orig.

side?

No

Final dest.

“Connec tedName

” updated at orig.

side?

No

Notes

No No No

Test Setup 2

Setup was as follows:

• PBX1 configured as NI2, emulates User

• Cisco Cisco 2621Gateway configured as PRI NI2, emulates Network

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 17 of 34

.

Table 6 Switch and Gateway Settings

Siemens Hicom 330 E CS

Switch-type/ Protocol side setting

NI2/User

Cisco 2621_B ISDN protocol-type/

Protocol side setting isdn switch-type—primary-ni isdn protocol—emulate network

When the Cisco 2621 router is set to emulate Network side, the Siemens PBX must send at least 10 digits for the router to properly route the call. Since the PBX is configured for 4 digit dialing, calls were tested in one direction only, from Cisco 7960 IP phone to Siemens digital phone. The test results are expected to be the same. Refer to the tables 2 - 7 for details.

Appendix A

Call Manager Software Release:

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 18 of 34

Siemens Hicom 330 E CS Software release

-------------------------------------------------------------------------------

TERMINAL 1 L O G O N 01-09-18 11:40:46

-------------------------------------------------------------------------------

<dis-ansu

DIS-ANSU;

H500: AMO ANSU STARTED

APS TYPE | NAME | SP REFERENCE NO.

-------------+----------+------------------

SWU RES-CODE | S0-ET0SC | P30252B6500S00101

SWU AMO-CODE | B0-ET0BC | P30252B6500B00101

SWU RES-TEXT | S0-TTDSD | P30252B650DS00101

SYSTEM NUMBER | DB SUBSYSTEM NAME

------------------+------------------

00000000000095393 | DB_SUSY_ZDBCCDSF

00000000000095393 | DB_SUSY_ZDBCCDS0

00000000000095393 | DB_SUSY_ZDBCCDS1

00000000000095393 | DB_SUSY_ZDBCCDS2

00000000000095393 | DB_SUSY_ZDBCCDSB

00000000000095393 | DB_SUSY_ZDBCCDSC

AMO-ANSU -135 ENTERING THE SYSTEM NUMBERS INTO THE SWU DATABASE

DISPLAY COMPLETED;

<

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 19 of 34

Cisco 2621 Router Configuration

2621_B#sh ver

Cisco Internetwork Operating System Software

IOS (tm) C2600 Software (C2600-JS-M), Version 12.2(3.5)T, MAINTENANCE INTERIM S

OFTWARE

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2001 by cisco Systems, Inc.

Compiled Fri 03-Aug-01 22:45 by ccai

Image text-base: 0x80008088, data-base: 0x81631DD8

ROM: System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1)

2621_B uptime is 1 week, 4 days, 3 hours, 15 minutes

System returned to ROM by power-on

System image file is "flash:c2600-js-mz.122-3.5.T" cisco 2621 (MPC860) processor (revision 0x200) with 56320K/9216K bytes of memory

.

Processor board ID JAD051516TX (503811939)

M860 processor: part number 0, mask 49

Bridging software.

X.25 software, Version 3.0.0.

SuperLAT software (copyright 1990 by Meridian Technology Corp).

TN3270 Emulation software.

Primary Rate ISDN software, Version 1.1.

2 FastEthernet/IEEE 802.3 interface(s)

24 Serial network interface(s)

2 Channelized T1/PRI port(s)

32K bytes of non-volatile configuration memory.

16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

2621_B#

_______________________________________________________________________________________

__

2621_B#sh diag

Slot 0:

C2621 2FE Mainboard Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware Revision : 2.0

PCB Serial Number : JAD051516TX (503811939)

Part Number : 73-3200-08

RMA History : 00

RMA Number : 0-0-0-0

Board Revision : A0

Deviation Number : 0-21249

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 00 A2 41 02 00 C1 17 4A 41 44 30 35 31

0x10: 35 31 36 54 58 20 28 35 30 33 38 31 31 39 33 39

0x20: 29 82 49 0C 80 08 04 00 81 00 00 00 00 42 41 30

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 20 of 34

0x30: 80 00 00 53 01 FF FF FF FF FF FF FF FF FF FF FF

0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Slot 1:

High Density Voice Port adapter

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware Revision : 1.1

Top Assy. Part Number : 800-03567-01

Board Revision : F1

Deviation Number : 0-0

Fab Version : 02

PCB Serial Number : JAB05080LU9

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 00 CC 41 01 01 C0 46 03 20 00 0D EF 01

0x10: 42 46 31 80 00 00 00 00 02 02 C1 8B 4A 41 42 30

0x20: 35 30 38 30 4C 55 39 03 00 81 00 00 00 00 04 00

0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

VIC Slot 0:

T1 (2 Port) Multi-Flex Trunk (Drop&Insert) WAN Daughter Card

Hardware revision 1.0 Board revision B0

Serial number 17759676 Part number 800-04614-01

Test history 0x0 RMA number 00-00-00

Connector type PCI

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 24 01 00 01 0E FD BC 50 12 06 01 00 00 00 00

0x30: 58 00 00 00 00 01 15 00 FF FF FF FF FF FF FF FF

HDV firmware: Compiled Fri 23-Mar-01 00:20 by miriyala

HDV memory size 524280 heap free 175065

2621_B#

_______________________________________________________________________________________

__

2621_B#sh controllers t1 1/0

T1 1/0 is up.

Applique type is Channelized T1

Cablelength is long gain36 0db

No alarms detected.

alarm-trigger is not set

Version info Firmware: 20010710, FPGA: 15

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 21 of 34

Framing is ESF, Line Code is B8ZS, Clock Source is Line.

Data in current interval (184 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

2621_B#

_______________________________________________________________________________________

__

2621_B#sh conf

2621_B#sh configuration

Using 1824 out of 29688 bytes

!

version 12.2

no parser cache service timestamps debug datetime msec localtime show-timezone service timestamps log uptime no service password-encryption

!

hostname 2621_B

!

no logging buffered enable password cisco

!

!

!

memory-size iomem 15 voice-card 1

dspfarm

!

ip subnet-zero

!

!

no ip domain-lookup

!

isdn switch-type primary-ni

!

!

!

!

!

!

voice class codec 1

codec preference 1 g729r8

codec preference 2 g711ulaw

codec preference 3 g711alaw

!

!

!

controller T1 1/0

framing esf

linecode b8zs

pri-group timeslots 1-24

!

controller T1 1/1

shutdown

framing esf

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 22 of 34

linecode b8zs

!

!

!

!

interface FastEthernet0/0

ip address 192.168.100.2 255.255.255.0

no ip mroute-cache

load-interval 30

no keepalive

speed auto

half-duplex

!

interface FastEthernet0/1

ip address 10.1.1.129 255.255.255.0

no ip mroute-cache

duplex auto

speed auto

!

interface Serial1/0:23

no ip address

no logging event link-status

isdn switch-type primary-ni

isdn incoming-voice voice

isdn T309-enable

isdn T306 30000

isdn T310 40000

no cdp enable

!

router rip

network 1.0.0.0

network 192.168.100.0

!

ip classless no ip http server ip pim bidir-enable

!

dialer-list 1 protocol ip permit dialer-list 1 protocol ipx permit

!

!

snmp-server packetsize 4096 snmp-server manager tftp-server nvram call rsvp-sync

!

voice-port 1/0:23

!

!

mgcp profile default

!

dial-peer cor custom

!

!

!

dial-peer voice 1 pots

destination-pattern 2...

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 23 of 34

direct-inward-dial

port 1/0:23

prefix 2

!

dial-peer voice 3 voip

destination-pattern 5...

progress_ind setup enable 1

voice-class codec 1

session target ipv4:10.1.1.2

dtmf-relay h245-alphanumeric

!

!

line con 0

exec-timeout 0 0 line aux 0

exec-timeout 0 0 line vty 0 4

exec-timeout 0 0

password cisco

login line vty 5 15

exec-timeout 0 0

login

!

scheduler allocate 3996 1000

!

end

2621_B#

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 24 of 34

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 25 of 34

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 26 of 34

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 27 of 34

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 28 of 34

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 29 of 34

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 30 of 34

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 31 of 34

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 32 of 34

Cisco Systems, Inc.

All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.

Page 33 of 34

Corporate Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 526-4100

European Headquarters

Cisco Systems International BV

Haarlerbergpark

Haarlerbergweg 13-19

1101 CH Amsterdam

The Netherlands www-europe.cisco.com

Tel: 31 0 20 357 1000

Fax: 31 0 20 357 1100

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA www.cisco.com

Tel: 408 526-7660

Fax: 408 527-0883

Asia Pacific Headquarters

Cisco Systems, Inc.

Capital Tower

168 Robinson Road

#22-01 to #29-01

Singapore 068912 www.cisco.com

Tel: +65 317 7777

Fax: +65 317 7799

Cisco Systems has more than 200 offices in the following countries and regions. Addresses, phone numbers, and fax numbers are listed on the

C i s c o W e b s i t e a t w w w . c i s c o . c o m / g o / o f f i c e s

Argentina • Australia • Austria • Belgium • Brazil • Bulgaria • Canada • Chile • China PRC • Colombia • Costa Rica • Croatia

Czech Republic • Denmark • Dubai, UAE • Finland • France • Germany • Greece • Hong Kong SAR • Hungary • India • Indonesia • Ireland

Israel • Italy • Japan • Korea • Luxembourg • Malaysia • Mexico • The Netherlands • New Zealand • Norway • Peru • Philippines • Poland

Portugal • Puerto Rico • Romania • Russia • Saudi Arabia • Scotland • Singapore • Slovakia • Slovenia • South Africa • Spain • Sweden

S w i t z e r l a n d • Ta i w a n • T h a i l a n d • Tu r k e y • U k r a i n e • U n i t e d K i n g d o m • U n i t e d S t a t e s • Ve n e z u e l a • Vi e t n a m • Z i m b a b w e

All contents are Copyright © 1992–2002, Cisco Systems, Inc. All rights reserved. CCIP, the Cisco Arrow logo, the Cisco Powered Network mark, the Cisco Systems Verified logo, Cisco Unity, Follow Me Browsing, FormShare,

Internet Quotient, iQ Breakthrough, iQ Expertise, iQ FastTrack, the iQ logo, iQ Net Readiness Scorecard, Networking Academy, ScriptShare, SMARTnet, TransPath, and Voice LAN are trademarks of Cisco Systems,

Inc.; Changing the Way We Work, Live, Play, and Learn, Discover All That’s Possible, The Fastest Way to Increase Your Internet Quotient, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST,

BPX, Catalyst, CCDA, CCDP, CCIE, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, the Cisco IOS logo, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo,

Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherSwitch, Fast Step, GigaStack, IOS, IP/TV, LightStream, MGX, MICA, the Networkers logo, Network Registrar, Packet, PIX, Post-Routing,

Pre-Routing, RateMUX, Registrar, SlideCast, StrataView Plus, Stratm, SwitchProbe, TeleRouter, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries.

All other trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.

(0206R)

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals