Aiwa | User manual | NSX-VC8 HR

NSX-VC8
HR
SERVICE MANUAL
COMPACT DISC
STEREO SYSTEM
BASIC TAPE MECHANISM : ZZM-2 PR1NM
BASIC CD MECHANISM : 3ZG-3 E8NM
SYSTEM
CD
CASSEIVER
SPEAKER
REMOTE
CONTROLLER
NSX-VC8
CX–NVC8
SX-NVC8
RC–AAS09
S/M Code No. 09-00A-437-8R1
RE
VI
SIO
DA
N
TA
• This Service Manual is the "Revision Publishing" and replaces "Simple Manual"
NSX-VC8 (HR), (S/M Code No. 09-009-437-8T1).
SPECIFICATIONS
<FM tuner section>
Tuning range
Usable sensitivity (IHF)
Antenna terminals
<AM tuner section>
Tuning range
Usable sensitivity
Antenna
<Amplifier section>
Power output
Total harmonic distortion
Inputs
Outputs
<Cassette deck section>
Track format
Frequency response
Recording system
Heads
87.5 MHz to 108 MHz
13.2 dBf
75 ohms (unbalanced)
531 kHz to 1602 kHz (9kHz step)
530 kHz to 1710 kHz (10 kHz step)
350 µV/m
Loop antenna
Rated: 16 W + 16 W (6 ohms,
T.H.D. 1 %, 1 kHz)
Reference: 20 W + 20W (6 ohms,
T.H.D. 10 %, 1 kHz)
0.1 % (10 W, 1 kHz, 6 ohms, DIN
AUDIO)
VIDEO/AUX: 600 mV
MIC: 1 mV (10 kohms)
SPEAKERS: 6 ohms or more
PHONES: 32 ohms or more
VIDEO OUT: 1 Vp-p (75 ohms)
<Compact disc player section>
Laser
Semiconductor laser (λ =780 nm)
Video signal
NTSC / PAL color format (selectable)
VIdeo data
MPEG 1
Audio data
MPEG 1, Layer 2
<Speaker system SX–NVC8>
Speaker system
Speaker units
Impedance
Dimensions (W x H x D)
Weight
<General>
Power requirements
Power consumption
Dimensions (W x H x D)
Weight
1 way, bass reflex
Full range: 100 mm cone
6 ohms
196 x 301 x 198 mm
1.8 kg
120 V / 220 - 230 V/ 240 V AC
(switchable), 50 Hz / 60 Hz
80 W
260 x 302.5 x 266 mm
4.2 kg
• Specifications and external appearance are subject to change
without notice.
4 tracks, 2 channels stereo
50 Hz – 8000 Hz
AC bias
Deck 1: recording/playback x 1,
erase x 1
Deck 2: playback x 1
–2–
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully
the instructions below when servicing.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herin may result in
hazardous radiation exposure.
ATTENTION
L’utillisation de commandes, réglages ou procédures
autres que ceux spécifiés peut entraîner une dangereuse
exposition aux radiations.
ADVARSEL
s
s
Caution: Invisible laser radiation when
open and interlocks defeated avoid
exposure to beam.
Advarsel: Usynlig laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
VARNING!
Om apparaten används på annat sätt än vad som
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
Precaution to replace Optical block
PICK-UP Assy PWB
(KSS-213F)
Body or clothes electrostatic potential could
ruin laser diode in the optical block. Be sure
ground body and workbench, and use care the
clothes do not touch the diode.
1) After the connection, remove solder shown in
right figure.
Solder
–3–
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.
Discharge procedure
MAIN C.B
1 Remove the AC power cord.
2 Connect a discharging resistor at an end of lead wire that
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
3 Contact the other end of the discharging resistor to the
positive (+) side (+VH) of C101. (For two seconds)
4 Contact the same end of the discharging resistor as step
3 to the negative (-) side (-VH) of C102 in the same way.
(For two seconds)
5 Check that voltage across C101 and C102 has decreased
to 1 V or less using a multimeter or an oscilloscope.
D101
3
2
Select a discharging resistor referring to the following table.
C102
4
2
Fig-1
Charging voltage (V)
Discharging
(C101, 102)
resistor (Ω)
25-48
100
3
87-A00-247-090
49-140
220
5
87-A00-232-090
Rated power (W)
C101
Parts number
Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.
2. Check items before exchanging the MICROCOMPUTER
Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.
2-1. Regarding the HOLD terminal of the MICROCOMPUTER
When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.
• Good or no good judgement of the MICROCOMPUTER
1 Turn on the AC main power.
2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.
3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the
MICROCOMPUTER is judged to be good.
–4–
In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.
2-2. Regarding reset
TE
R
There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.
1 Remove the AC power cord.
M
IC
RO
CO
M
PU
FRONT C.B
18
15
C113
% VSS
MICROC113
COMPUTER
* VDD
FRONT C.B
Short with tweezers.
Fig-2-2
2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
good.
Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.
2-3. Confirmation of soldering state of MICROCOMPUTER
Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.
–5–
ELECTRICAL MAIN PARTS LIST
REF. NO. PART NO.
KANRI
NO.
REF. NO. PART NO.
DESCRIPTION
KANRI
NO.
DESCRIPTION
MAIN C.B
IC
87-A21-381-040
87-A21-557-010
8Z-ZJP-602-010
87-017-760-080
87-A20-925-040
C-IC,LA9235M
C-IC,LC78635E
C-IC,UPD78016FGC-574-AB8
IC,M51943BML
C-IC,BA05FP
C9
C10
C11
C12
C21
87-010-759-080
87-010-759-080
87-010-759-080
87-010-759-080
87-A10-520-000
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
CAP,E 3300-35 M SMG
87-A20-905-040
87-A21-513-040
87-A21-419-040
87-A20-920-010
8A-NHC-602-010
C-IC,BA033FP
C-IC,BA6998FP
C-IC,NJM14558MD-TE2
C-IC,CL680-D1
C-IC,M38B57MCH-E260FP
C22
C25
C26
C31
C32
87-016-051-000
87-010-406-080
87-010-406-080
87-010-759-080
87-012-286-080
CAP,E 2200-35 M SMG
CAP, ELECT 22-50
CAP, ELECT 22-50
C-CAP,U, 0.1-25F
CAP, U 0.01-25
87-070-083-010
87-A20-921-040
87-A20-962-040
84-ZG1-695-040
87-A20-975-040
IC,GP1U281X
C-IC,SN74LVU04APW
C-IC,MSM54V16258B/BSL
C-IC,LH5V2RN1
C-IC,SN74LV74APW
C34
C35
C36
C50
C51
87-010-247-080
87-010-406-080
87-010-112-080
87-010-247-080
87-010-247-080
CAP,
CAP,
CAP,
CAP,
CAP,
ELECT
ELECT
ELECT
ELECT
ELECT
100-50V
22-50
100-16V
100-50V
100-50V
87-A21-443-040
87-A20-918-040
87-A20-974-040
87-A21-560-010
87-070-127-110
C-IC,M62495AFP
C-IC,SM5878AM
C-IC,LC74781M-9017
IC,LA1844L-A
IC,LC72131 D
C60
C61
C81
C82
C83
87-010-403-080
87-010-260-080
87-010-401-080
87-010-407-080
87-010-260-080
CAP,
CAP,
CAP,
CAP,
CAP,
ELECT
ELECT
ELECT
ELECT
ELECT
3.3-50V
47-25V
1-50V
33-50V
47-25V
C101
C102
C103
C104
C105
87-012-282-080
87-012-282-080
87-010-544-080
87-010-544-080
87-012-282-080
CAP,
CAP,
CAP,
CAP,
CAP,
U 4700P-50
U 4700P-50
ELECT 0.1-50V
ELECT 0.1-50V
U 4700P-50
C106
C107
C108
C111
C112
87-012-282-080
87-010-403-080
87-010-403-080
87-010-406-080
87-010-406-080
CAP,
CAP,
CAP,
CAP,
CAP,
U 4700P-50
ELECT 3.3-50V
ELECT 3.3-50V
ELECT 22-50
ELECT 22-50
C113
C114
C117
C118
C119
87-A10-946-080
87-A10-946-080
87-012-286-080
87-012-286-080
87-012-286-080
C-CAP,S 220P-100 J CH
C-CAP,S 220P-100 J CH
CAP, U 0.01-25
CAP, U 0.01-25
CAP, U 0.01-25
C120
C125
C126
C127
C128
87-012-286-080
87-010-759-080
87-010-759-080
87-010-759-080
87-010-759-080
CAP, U 0.01-25
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
C140
C401
C402
C403
C404
87-010-190-080
87-010-759-080
87-010-759-080
87-012-193-080
87-012-193-080
S CHIP F 0.01
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
C-CAP,U 82P-50 CH
C-CAP,U 82P-50 CH
C405
C406
C407
C408
C409
87-012-286-080
87-012-286-080
87-012-286-080
87-012-286-080
87-012-278-080
CAP, U 0.01-25
CAP, U 0.01-25
CAP, U 0.01-25
CAP, U 0.01-25
C-CAP,U 2200P-50 B
C410
C411
C412
C413
C421
87-012-278-080
87-010-405-080
87-010-405-080
87-012-286-080
87-012-275-080
C-CAP,U 2200P-50 B
CAP, ELECT 10-50V
CAP, ELECT 10-50V
CAP, U 0.01-25
C-CAP,U 1200P-50 B
C422
C423
C424
C425
C426
87-012-275-080
87-012-274-080
87-012-274-080
87-010-263-080
87-010-263-080
C-CAP,U 1200P-50 B
CHIP CAP,U 1000P-50B
CHIP CAP,U 1000P-50B
CAP, ELECT 100-10V
CAP, ELECT 100-10V
C427
C428
C429
C430
C431
87-012-188-080
87-012-188-080
87-010-598-080
87-010-598-080
87-012-284-080
C-CAP,U 47P-50 CH
C-CAP,U 47P-50 CH
C-CAP,S 0.068-16VRK
C-CAP,S 0.068-16VRK
CAP, U 6800P-50
C432
C433
C434
C435
87-012-284-080
87-010-546-080
87-010-546-080
87-010-263-080
CAP,
CAP,
CAP,
CAP,
TRANSISTOR
87-026-609-080
87-A30-076-080
89-213-702-010
87-026-610-080
87-A30-074-080
TR,KTA1266GR
C-TR,2SC3052F
TR,2SB1370 (1.8W)
TR,KTC3198GR
C-TR,RT1P 141C
87-A30-075-080
87-A30-190-080
87-A30-256-010
87-A30-255-010
87-A30-107-070
C-TR,2SA1235F
TR,CC5551
TR,2SD1933
TR,2SB1342
C-TR,CMBT5401
87-A30-106-040
87-026-231-080
87-026-237-080
87-A30-104-080
87-A30-520-080
C-TR,CMBT5551
CHIP-TRANSISTER,DTA124XK
CHIP-TR,DTC124XK
C-TR,RT1N 441C
TR,2SC5342Y
87-A30-090-080
87-A30-091-080
87-A30-062-080
87-A30-318-080
87-A30-492-080
FET,2SK2541
FET,2SJ460
C-TR,KRC104S
TR,CSA952K
TR,2SC5343G
87-A30-234-080
89-327-125-080
87-026-580-080
87-026-470-080
89-111-625-080
TR,CSC4115BC
CHIP TR,2SC2712GR
C-TR,DTA123JK
C-TR,HN1C03F (0.3W)
C-TR,2SA1162GR (0.15W)
87-A30-521-080
87-A30-489-080
89-503-602-080
89-327-143-080
C-TR,2SC5345S(O)
C-TR,KRA107S
C-FET,2SK360E
TR,2SC2714O (0.1W)
87-A40-393-090
87-A40-553-080
87-A40-777-080
87-020-465-080
87-A40-764-080
DIODE,1N5402GW(F20)
DIODE,1N4003 LES
ZENER,UZ30BSB
DIODE,1SS133 (110MA)
ZENER,UZ10BSC
87-A40-313-080
87-A40-269-080
87-A40-270-080
87-017-024-040
87-A40-749-080
C-DIODE,MC 2840
C-DIODE,MC2836
C-DIODE,MC2838
C-DIODE,DA204K
ZENER,UZ5.6BSB
87-020-027-080
87-A40-739-080
87-A40-751-080
87-A40-748-080
87-A40-760-080
CHIP-DIODE 1SS184
ZENER,UZ2.7BSA
ZENER,UZ6.2BSB
ZENER,UZ5.6BSA
ZENER,UZ9.1BSA
DIODE
–6–
U 6800P-50
ELECT 0.33-50V
ELECT 0.33-50V
ELECT 100-10V
REF. NO. PART NO.
REF. NO. PART NO.
KANRI
NO.
CAP,
CAP,
CAP,
CAP,
CAP,
DESCRIPTION
C441
C442
C443
C445
C452
87-010-759-080
87-010-759-080
87-010-759-080
87-A10-039-080
87-010-382-080
KANRI
DESCRIPTION
NO.
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
C-CAP,U 470P-50 J CH
CAP, ELECT 22-25V
C453
C454
C455
C456
C460
87-012-279-080
87-012-279-080
87-012-279-080
87-012-286-080
87-010-759-080
C-CAP,U 2700P-50 B
C-CAP,U 2700P-50 B
C-CAP,U 2700P-50 B
CAP, U 0.01-25
C-CAP,U, 0.1-25F
C851
C852
C853
C858
C859
87-012-286-080
87-012-286-080
87-012-286-080
87-010-759-080
87-010-759-080
CAP, U 0.01-25
CAP, U 0.01-25
CAP, U 0.01-25
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
C461
C462
C470
C605
C606
87-012-158-080
87-012-158-080
87-A10-039-080
87-012-275-080
87-012-275-080
C-CAP,S
C-CAP,S
C-CAP,U
C-CAP,U
C-CAP,U
C860
C902
C908
C909
C911
87-012-286-080
87-018-145-080
87-012-174-080
87-012-349-080
87-012-170-080
CAP, U 0.01-25
CAP,TC-U 6.8P-50 CH
CAP CHIP CERA SS 12P CHJ
C-CAP,S 1000P-50 CH
C-CAP,U 8P-50 CH
C609
C610
C611
C612
C613
87-010-785-080
87-010-785-080
87-010-545-080
87-010-545-080
87-010-545-080
C-CAP,U0.015-25BK
C-CAP,U0.015-25BK
CAP, ELECT 0.22-50V
CAP, ELECT 0.22-50V
CAP, ELECT 0.22-50V
C912
C913
C914
C915
C918
87-012-195-080
87-012-286-080
87-012-286-080
87-012-286-080
87-012-165-080
C-CAP,U 100P-50CH
CAP, U 0.01-25
CAP, U 0.01-25
CAP, U 0.01-25
CAP 3P
C614
C615
C616
C617
C618
87-010-545-080
87-012-172-080
87-010-248-080
87-016-459-080
87-010-405-080
CAP, ELECT 0.22-50V
CAPACITOR CHIP U 10P CH
CAP, ELECT 220-10V
CAP,E 470-10 SMG
CAP, ELECT 10-50V
C920
C921
C922
C923
C924
87-012-180-080
87-012-186-080
87-012-174-080
87-A10-039-080
87-012-174-080
C-CAP,U 22P-50 CH
C-CAP,U 39P-50 CH
CAP CHIP CERA SS 12P CHJ
C-CAP,U 470P-50 J CH
CAP CHIP CERA SS 12P CHJ
C630
C669
C670
C671
C672
87-A10-248-080
87-012-195-080
87-012-195-080
87-010-831-080
87-010-831-080
C-CAP,U0.1-16KBR
C-CAP,U 100P-50CH
C-CAP,U 100P-50CH
C-CAP,U,0.1-16F
C-CAP,U,0.1-16F
C927
C961
C962
C971
C972
87-012-195-080
87-012-170-080
87-010-401-080
87-010-381-080
87-010-404-080
C-CAP,U 100P-50CH
C-CAP,U 8P-50 CH
CAP, ELECT 1-50V
CAP, ELECT 330-16V
CAP, ELECT 4.7-50V
C673
C677
C679
C681
C682
87-012-278-080
87-012-286-080
87-A11-112-080
87-010-401-080
87-010-759-080
C-CAP,U 2200P-50 B
CAP, U 0.01-25
CAP,TC U 1000P-50 J CH
CAP, ELECT 1-50V
C-CAP,U, 0.1-25F
C973
C974
C979
C981
C982
87-012-286-080
87-012-286-080
87-012-195-080
87-010-260-080
87-010-759-080
CAP, U 0.01-25
CAP, U 0.01-25
C-CAP,U 100P-50CH
CAP, ELECT 47-25V
C-CAP,U, 0.1-25F
C683
C771
C772
C782
C783
87-010-260-080
87-010-263-080
87-012-286-080
87-012-286-080
87-012-286-080
CAP,
CAP,
CAP,
CAP,
CAP,
ELECT 47-25V
ELECT 100-10V
U 0.01-25
U 0.01-25
U 0.01-25
C983
C984
C987
C990
C991
87-012-286-080
87-012-286-080
87-012-286-080
87-012-195-080
87-012-176-080
CAP, U 0.01-25
CAP, U 0.01-25
CAP, U 0.01-25
C-CAP,U 100P-50CH
CAP 15P
C784
C785
C786
C788
C789
87-012-286-080
87-012-286-080
87-012-286-080
87-012-167-080
87-A10-801-080
CAP, U 0.01-25
CAP, U 0.01-25
CAP, U 0.01-25
C-CAP,U 5P-50 CH
C-CAP,S 0.022-16 J B CM
C992
C993
C994
C995
C996
87-012-176-080
87-012-274-080
87-012-195-080
87-012-274-080
87-012-195-080
CAP 15P
CHIP CAP,U 1000P-50B
C-CAP,U 100P-50CH
CHIP CAP,U 1000P-50B
C-CAP,U 100P-50CH
C790
C791
C792
C793
C795
87-A10-801-080
87-010-759-080
87-012-286-080
87-010-404-080
87-012-286-080
C-CAP,S 0.022-16 J B CM
C-CAP,U, 0.1-25F
CAP, U 0.01-25
CAP, ELECT 4.7-50V
CAP, U 0.01-25
C997
C998
C999
CF831
CF832
87-010-759-080
87-010-260-080
87-A11-155-080
87-008-261-010
87-008-261-010
C-CAP,U, 0.1-25F
CAP, ELECT 47-25V
CAP,TC U 0.01-16 Z F
FILTER, SFE10.7MA5-A
FILTER, SFE10.7MA5-A
C796
C797
C798
C799
C800
87-012-286-080
87-010-405-080
87-012-286-080
87-010-407-080
87-010-829-080
CAP,
CAP,
CAP,
CAP,
CAP,
U 0.01-25
ELECT 10-50V
U 0.01-25
ELECT 33-50V
U 0.047-16
CN81
CN351
CN401
CN601
CNA351
87-009-030-010
87-A60-625-010
87-A60-620-010
87-099-194-010
8A-NEC-634-010
CONNECTOR 2P PH M
CONN,8P V 2MM JMT
CONN,3P V 2MM JMT
CONN,6P 6216V
CONN ASSY,8P RPB
C801
C802
C803
C804
C807
87-010-403-080
87-010-829-080
87-010-787-080
87-010-263-080
87-010-400-080
CAP,
CAP,
CAP,
CAP,
CAP,
ELECT 3.3-50V
U 0.047-16
U 0.022-25
ELECT 100-10V
ELECT 0.47-50V
CNA401
D902
D903
F101
FC101
8A-NEC-633-010
87-A40-916-040
87-A40-916-040
87-035-223-010
87-033-213-080
CONN ASSY,3P (PH)
C-VARI-CAP,HVC202A
C-VARI-CAP,HVC202A
FUSE, 1.25AT
CLAMP, FUSE
C808
C809
C810
C814
C815
87-010-401-080
87-010-401-080
87-010-759-080
87-012-286-080
87-010-400-080
CAP, ELECT 1-50V
CAP, ELECT 1-50V
C-CAP,U, 0.1-25F
CAP, U 0.01-25
CAP, ELECT 0.47-50V
FC102
FC601
J101
J103
J271
87-033-213-080
88-906-201-110
87-A60-602-010
87-A61-452-010
87-A61-243-010
CLAMP, FUSE
FF-CABLE,6P 1.25
JACK,DIA6.3 BLK ST W/SW TC
TERMINAL,SP 4P(MSC)
JACK,6.3 BLK MONO W/SW V MSC
C816
C821
C823
C824
C825
87-010-400-080
87-010-405-080
87-010-177-080
87-010-404-080
87-010-596-080
CAP, ELECT 0.47-50V
CAP, ELECT 10-50V
C-CAP,S 820P-50 SL
CAP, ELECT 4.7-50V
CAP, S 0.047-16
J602
J831
L101
L102
L451
87-A60-881-010
87-A60-202-010
87-A50-610-010
87-A50-610-010
87-007-342-010
JACK,PIN 2P MSP 242V05 PBSN
TERMINAL,ANT 4P MSP-154V-02
COIL,1UH K(MDEC)
COIL,1UH K(MDEC)
COIL,OSC 85K BIAS
390P-50 CH
390P-50 CH
470P-50 J CH
1200P-50 B
1200P-50 B
!
!
!
–7–
C836
C837
C842
C844
C850
87-012-286-080
87-012-286-080
87-012-286-080
87-012-286-080
87-010-260-080
U 0.01-25
U 0.01-25
U 0.01-25
U 0.01-25
ELECT 47-25V
REF. NO. PART NO.
REF. NO. PART NO.
KANRI
DESCRIPTION
NO.
COIL,FM DET-N(TOK)
FLTR,PCFJZH-450 L(TOK)
COIL,2.2UH(CECS)
COIL,2.2UH(CECS)
COIL,FM-RF-U2 2G
KANRI
DESCRIPTION
NO.
C-CAP,U, 0.1-25F
CAP,E 470-10 SMG
CAP,E 10-50
CAP,E 100-25 SME
CONN,10P V 9604S-10C
C540
C541
C543
C590
CN201
87-010-759-080
87-016-459-040
87-010-405-040
87-010-384-040
87-A60-058-010
COIL,FM-RF-U1 2G
COIL,2.2UH(CECS)
COIL,FM OSC U 2G
COIL,FM IFT 7-6.2 (COILS)
COIL,AM PACK 4(TOK)
CN501
EMI271
FC201
FL501
L501
87-A60-673-010
87-008-372-080
88-910-231-110
8A-NEC-601-010
87-A50-655-010
CONN,9P H 2MM JMT
FILTER, EMI BL OIRNI
FF-CABLE,10P 1.25 230MM
FL,HNA-10SS15T
COIL,CLK 4.19MHZ (TOKO)7KLY
8A-NHC-605-010
87-A00-258-080
87-A00-258-080
87-012-286-080
87-045-389-010
PT,ANH-C HR
RES,M/F 0.22-1W J
RES,M/F 0.22-1W J
CAP, U 0.01-25
RELAY,OSA-SS-212DM5
S201
S202
S203
S204
S205
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
SW,TACT
SW,TACT
SW,TACT
SW,TACT
SW,TACT
EVQ11G04M
EVQ11G04M
EVQ11G04M
EVQ11G04M
EVQ11G04M
S1
T101
T102
TH101
TH102
87-A90-165-010
87-A60-317-010
87-A60-317-010
87-A91-042-080
87-A91-042-080
SW,SL 1-2-3 SWS2301
TERMINAL, 1P MSC
TERMINAL, 1P MSC
C-THMS,100K 55001
C-THMS,100K 55001
S206
S208
S209
S210
S211
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
SW,TACT
SW,TACT
SW,TACT
SW,TACT
SW,TACT
EVQ11G04M
EVQ11G04M
EVQ11G04M
EVQ11G04M
EVQ11G04M
X991
87-A70-061-010
VIB,XTAL 4.500MHZ CSA-309
S212
S213
SFR501
VR271
87-A90-095-080
87-A90-095-080
87-024-431-080
87-NB7-602-010
SW,TACT EVQ11G04M
SW,TACT EVQ11G04M
SFR,3.3K RH063EC
VR,RTRY 10KAX1 1 V
C201
C202
C203
C204
C271
87-010-401-040
87-010-759-080
87-010-260-040
87-016-251-040
87-012-282-080
CAP,E 1-50 SME
C-CAP,U, 0.1-25F
CAP,E 47-25 SME
CAP,E 220-16 SMG
CAP, U 4700P-50
C272
C273
C274
C275
C276
87-010-112-040
87-010-545-040
87-012-195-080
87-010-545-040
87-A10-248-080
CAP,E 100-16
CAP,E 0.22-50 SME
C-CAP,U 100P-50CH
CAP,E 0.22-50 SME
C-CAP,U0.1-16KBR
C1
C2
C3
C4
C5
87-A10-222-040
87-010-759-080
87-010-260-080
87-A10-222-040
87-012-286-080
CAP,AS 22-10 OS
C-CAP,U, 0.1-25F
CAP, ELECT 47-25V
CAP,AS 22-10 OS
CAP, U 0.01-25
C277
C278
C279
C280
C281
87-010-405-040
87-012-195-080
87-010-405-040
87-010-759-080
87-010-177-080
CAP,E 10-50
C-CAP,U 100P-50CH
CAP,E 10-50
C-CAP,U, 0.1-25F
C-CAP,S 820P-50 SL
C6
C7
C8
C10
C11
87-010-405-080
87-010-263-080
87-012-274-080
87-010-546-080
87-010-401-080
CAP,
CAP,
CHIP
CAP,
CAP,
C282
C500
C505
C506
C507
87-010-177-080
87-010-759-080
87-010-829-080
87-010-263-040
87-010-246-040
C-CAP,S 820P-50 SL
C-CAP,U, 0.1-25F
CAP, U 0.047-16
CAP,E 100-10
CAP,E 47-35 SME
C13
C15
C16
C101
C102
87-012-193-080
87-012-286-080
87-010-260-080
87-A10-504-080
87-010-401-080
C-CAP,U 82P-50 CH
CAP, U 0.01-25
CAP, ELECT 47-25V
C-CAP,U 0.047-16 K B
CAP, ELECT 1-50V
C508
C509
C510
C511
C512
87-010-192-080
87-010-404-040
87-010-404-040
87-010-759-080
87-010-263-040
C-CAP,S 0.022-50 F
CAP,E 4.7-50 SME
CAP,E 4.7-50 SME
C-CAP,U, 0.1-25F
CAP,E 100-10
C103
C104
C105
C106
C107
87-010-759-080
87-010-759-080
87-010-260-080
87-012-195-080
87-010-759-080
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
CAP, ELECT 47-25V
C-CAP,U 100P-50CH
C-CAP,U, 0.1-25F
C514
C515
C517
C518
C523
87-012-274-080
87-012-274-080
87-010-759-080
87-012-268-080
87-010-248-040
CHIP CAP,U 1000P-50B
CHIP CAP,U 1000P-50B
C-CAP,U, 0.1-25F
C-CAP,U 330P-50 B
CAP,E 220-10 SME
C108
C109
C110
C111
C112
87-012-282-080
87-A10-504-080
87-012-195-080
87-010-260-080
87-012-286-080
CAP, U 4700P-50
C-CAP,U 0.047-16 K B
C-CAP,U 100P-50CH
CAP, ELECT 47-25V
CAP, U 0.01-25
C524
C525
C526
C527
C528
87-010-192-080
87-010-401-040
87-012-172-080
87-012-274-080
87-010-175-080
C-CAP,S 0.022-50 F
CAP,E 1-50 SME
CAPACITOR CHIP U 10P CH
CHIP CAP,U 1000P-50B
CAP 560P
C114
C115
C118
C119
C120
87-010-260-080
87-012-286-080
87-010-263-080
87-012-286-080
87-012-286-080
CAP,
CAP,
CAP,
CAP,
CAP,
C530
C531
C532
C533
C534
87-012-195-080
87-012-195-080
87-012-195-080
87-012-195-080
87-012-195-080
C-CAP,U
C-CAP,U
C-CAP,U
C-CAP,U
C-CAP,U
C123
C124
C125
C135
C201
87-A10-504-080
87-010-403-080
87-010-759-080
87-012-195-080
87-A10-248-080
C-CAP,U 0.047-16 K B
CAP, ELECT 3.3-50V
C-CAP,U, 0.1-25F
C-CAP,U 100P-50CH
C-CAP,U0.1-16KBR
C535
C536
C537
C538
C539
87-012-195-080
87-012-195-080
87-012-195-080
87-012-195-080
87-012-199-080
C-CAP,U 100P-50CH
C-CAP,U 100P-50CH
C-CAP,U 100P-50CH
C-CAP,U 100P-50CH
CAP 220P
C206
C207
C208
C209
C210
87-012-195-080
87-012-195-080
87-012-195-080
87-012-195-080
87-A10-248-080
C-CAP,U 100P-50CH
C-CAP,U 100P-50CH
C-CAP,U 100P-50CH
C-CAP,U 100P-50CH
C-CAP,U0.1-16KBR
C211
C213
C214
87-010-263-080
87-010-190-080
87-010-759-080
CAP, ELECT 100-10V
S CHIP F 0.01
C-CAP,U, 0.1-25F
L801
L802
L811
L832
L903
87-A50-608-010
87-A91-551-010
87-005-847-080
87-005-847-080
88-ZA1-602-110
L904
L906
L907
L908
L951
88-ZA1-601-010
87-005-847-080
8A-NEC-611-010
88-ZA1-624-010
8A-NF8-667-010
!
PT101
R129
R130
R790
RY101
!
!
!
FRONT C.B
CD C.B
100P-50CH
100P-50CH
100P-50CH
100P-50CH
100P-50CH
–8–
ELECT
ELECT
CAP,U
ELECT
ELECT
10-50V
100-10V
1000P-50B
0.33-50V
1-50V
ELECT 47-25V
U 0.01-25
ELECT 100-10V
U 0.01-25
U 0.01-25
REF. NO. PART NO.
REF. NO. PART NO.
KANRI
DESCRIPTION
NO.
CAP, ELECT 100-16V
C-CAP,U, 0.1-25F
CAP, ELECT 100-10V
C-CAP,U, 0.1-25F
CAP, ELECT 100-10V
KANRI
DESCRIPTION
NO.
CAP, U 0.01-25
C-CAP,U 120P-50 CH
CAP ELECT GAS 1/50
CAP, U 0.01-25
C-CAP,S 0.47-16 BK
C619
C701
C702
C703
C704
87-012-286-080
87-012-196-080
87-010-494-080
87-012-286-080
87-016-526-080
C-CAP,U, 0.1-25F
CAP, ELECT 220-16
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
C705
C706
C707
C708
C709
87-010-371-080
87-010-759-080
87-012-286-080
87-A11-167-080
87-A11-167-080
CAP, ELECT 470-6.3V
C-CAP,U, 0.1-25F
CAP, U 0.01-25
C-CAP,S 27P-50 F CH
C-CAP,S 27P-50 F CH
87-010-759-080
87-010-759-080
87-012-286-080
87-012-286-080
87-012-286-080
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
CAP, U 0.01-25
CAP, U 0.01-25
CAP, U 0.01-25
CN1
CN301
CN401
CN403
CN404
87-A60-424-010
87-099-199-010
87-099-199-010
87-A60-077-010
87-A60-082-010
CONN,16P V TOC-B
CONN,6P 6216 H
CONN,6P 6216 H
CONN,10P H 9604S-10F
CONN,05P H 9604S-05F
C504
C505
C506
C508
C509
87-012-172-080
87-012-172-080
87-012-286-080
87-010-263-080
87-016-669-080
CAPACITOR CHIP U 10P CH
CAPACITOR CHIP U 10P CH
CAP, U 0.01-25
CAP, ELECT 100-10V
C-CAP,S 0.1-25 K B
FB501
FC1
FC401
FC404
J701
87-008-372-080
8A-NHC-603-010
88-906-121-110
88-905-201-110
87-009-502-010
FILTER, EMI BL OIRNI
FF-CABLE,16P -1.0
FF-CABLE,6P
FF-CABLE, 5P 1.25
JACK,PIN 1P Y EARTH
C510
C511
C512
C513
C514
87-010-263-080
87-010-759-080
87-012-286-080
87-012-286-080
87-012-286-080
CAP, ELECT 100-10V
C-CAP,U, 0.1-25F
CAP, U 0.01-25
CAP, U 0.01-25
CAP, U 0.01-25
JR302
L502
L503
L504
L505
87-005-778-080
87-005-204-080
87-005-189-080
87-005-187-080
87-005-204-080
C-COIL,10UK NLC25
COIL,47UH
COIL 2.7UH
COIL,1.8UH
COIL,47UH
C518
C519
C520
C521
C523
87-012-195-080
87-012-145-080
87-012-157-080
87-012-197-080
87-012-286-080
C-CAP,U 100P-50CH
CAP, CHIP S 270P CH
C-CAP,S 330P-50 CH
C-CAP,U 150P-50 CH
CAP, U 0.01-25
L506
L507
L508
L701
R507
87-005-204-080
87-005-204-080
87-005-196-080
87-005-817-080
87-A00-408-080
COIL,47UH
COIL,47UH
COIL,10UH
C-COIL, 33UH J FLC32
C-RES,S 2K-1/10W D
C524
C525
C526
C527
C528
87-012-286-080
87-012-286-080
87-012-286-080
87-012-286-080
87-012-286-080
CAP,
CAP,
CAP,
CAP,
CAP,
R536
S201
X201
X501
X601
87-012-286-080
87-A90-162-010
87-A70-124-080
87-A70-125-080
87-030-270-080
CAP, U 0.01-25
SW,SL 1-1-3 SSSU
VIB,CER 8.0MHZ
VIB,XTAL 27MHZ 50PPM
VIB,XTAL 16.9344MHZ
C529
C530
C531
C532
C533
87-012-286-080
87-012-286-080
87-012-286-080
87-010-374-040
87-012-286-080
CAP, U 0.01-25
CAP, U 0.01-25
CAP, U 0.01-25
CAP,E 47-10
CAP, U 0.01-25
C534
C535
C536
C537
C538
87-010-263-080
87-012-286-080
87-010-078-040
87-010-190-080
87-010-759-080
CAP, ELECT 100-10V
CAP, U 0.01-25
CAP,E 47-6.3 5L
S CHIP F 0.01
C-CAP,U, 0.1-25F
C539
C540
C541
C542
C544
87-010-759-080
87-010-078-040
87-012-286-080
87-012-188-080
87-012-286-080
C-CAP,U, 0.1-25F
CAP,E 47-6.3 5L
CAP, U 0.01-25
C-CAP,U 47P-50 CH
CAP, U 0.01-25
C546
C560
C601
C602
C603
87-012-286-080
87-010-759-080
87-012-286-080
87-012-286-080
87-010-112-080
CAP, U 0.01-25
C-CAP,U, 0.1-25F
CAP, U 0.01-25
CAP, U 0.01-25
CAP, ELECT 100-16V
C604
C605
C606
C607
C608
87-010-759-080
87-012-286-080
87-012-286-080
87-012-178-080
87-012-178-080
C-CAP,U, 0.1-25F
CAP, U 0.01-25
CAP, U 0.01-25
C-CAP,U 18P-50 CH
C-CAP,U 18P-50 CH
C609
C610
C611
C612
C613
87-012-274-080
87-012-274-080
87-012-274-080
87-012-274-080
87-010-403-040
CHIP CAP,U 1000P-50B
CHIP CAP,U 1000P-50B
CHIP CAP,U 1000P-50B
CHIP CAP,U 1000P-50B
CAP,E 3.3-50 SME
C614
C615
C616
C617
C618
87-010-403-040
87-012-188-080
87-012-188-080
87-012-286-080
87-010-112-080
CAP,E 3.3-50 SME
C-CAP,U 47P-50 CH
C-CAP,U 47P-50 CH
CAP, U 0.01-25
CAP, ELECT 100-16V
C306
C307
C308
C309
C310
87-010-112-080
87-010-759-080
87-010-263-080
87-010-759-080
87-010-263-080
C311
C401
C402
C403
C404
87-010-759-080
87-010-101-080
87-010-759-080
87-010-759-080
87-010-759-080
C405
C406
C501
C502
C503
U
U
U
U
U
0.01-25
0.01-25
0.01-25
0.01-25
0.01-25
CD LOAD C.B
CON6
M1
SW1
SW2
87-099-210-010
87-045-305-010
87-036-110-010
87-036-110-010
CONN,5P 6216H
MOTOR,RF-500TB DC-5V(2MA)
PUSH SWITCH
PUSH SWITCH
CD DRIVE C.B
CON3
M20
M21
SW1
–9–
87-A60-086-010
87-045-358-010
87-045-356-010
87-A90-042-010
CONN,6P H 6216
MOT,RF-310TA 43
MOT,RF-310TA 30
SW,LEAF MSW-17310MVPO
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
8 8
A
Figure
Resistor Code
Value of resistor
Chip resistor
L
W
t
:A
Resistor Code : A
1.0
0.5
0.35
104
1.6
0.8
0.45
108
2
1.25
0.45
118
3.2
1.6
0.55
128
Dimensions (mm)
Wattage
1/16W
Type
1005
Symbol
CJ
Tolerance
5%
1/16W
1/10W
1608
2125
5%
5%
CJ
CJ
1/8W
3216
5%
CJ
Form
L
t
W
TRANSISTOR ILLUSTRATION
E C B
CC5551
CSA952K
KTA1266GR
KTC3198GR
E C B
E C B
2SC5342Y
2SC5343G
C1
E1
B C E
S
B2
C
E2
D
B1
2SB1342
2SB1370
2SD1933
CSC4115BC
B
G
C2
E
S D G
2SJ460
2SK2541
2SK360E
HN1C03F
– 10 –
2SA1162GR
2SA1235F
2SC2712GR
2SC2714O
2SC3052F
2SC5345S(0)
CMBT5401
CMBT5551
DTA123JK
DTA124XK
DTC124XK
KRA107S
KRC104S
RT1N441C
RT1P141C
WIRING – 1 (MAIN/FRONT)
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
I
J
K
(K-SCAN)
L
IMP: 6
M
N
4
5
3
1
O
P
Q
R
S
T
U
– 11 –
SCHEMATIC DIAGRAM _ 1 (MAIN 1 / 2 : AMP SECTION)
– 12 –
SCHEMATIC DIAGRAM _ 2 (MAIN 2 / 2 : TUNER SECTION)
– 13 –
SCHEMATIC DIAGRAM _ 3 (FRONT)
– 14 –
WIRING – 2 (CD) <1 / 2>
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
– 15 –
WIRING – 2 (CD) <2 / 2>
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
– 16 –
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
SCHEMATIC DIAGRAM _ 4 (CD : 1 / 2 / CD LOAD / CD DRIVE)
– 17 –
SCHEMATIC DIAGRAM _ 5 (CD : 2 / 2)
– 18 –
WIRING – 3 (DECK)
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
– 19 –
WIRING – 3 (CD LOAD/CD DRIVE)
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
– 20 –
FL (HNA-10SS15T) GRID ASSIGNMENT & ANODE CONNECTION
GRID ASSIGNMENT
ANODE CONNECTION
– 21 –
IC BLOCK DIAGRAM
– 22 –
– 23 –
IC DESCRIPTION
IC, M38B57MCH - E260FP
Pin No.
Pin Name
I/O
Description
1
NC
—
2
I-HOLD
I
Hold input.
3
I-TRAY SW
I
CD tray SW AD input.
4
I-D-SW
I
CD door open/close AD detection input. (Connected to GND through a resistor)
5
I-KEY2
I
Key AD input 2.
6
I-KEY1
I
Key AD input 1.
7
O-DSP DATA
—
Not used.
8
O-MOTOR
O
Cassette deck motor control output.
9
I-RMC
I
System remote control signal input. (Active "L")
10
RESET
I
Reset input for MICON.
11
I-STEREO
I
Tuner stereo detect input.
12
O-DSC/
O-PLL.DATA
O
Function IC control output/PLL data output.
13
VSS
—
Connected to GND.
14
XIN
I
4.19MHZ oscillator circuit.
15
XOUT
O
4.19MHZ oscillator circuit.
16
VCC
—
Power supply.
17
O-PB1
O
Cassette deck output switching PB1/PB2.
18
O-POWER
O
Power control ON/OFF output.
19
O-C.SHIFT
O
Clock shift output for micro computer when tuner receiving broadcast.
20
O-RMT
O
REC MUTE output.
21
O-BIAS
O
Bias ON/OFF output.
22
O-TU ON
O
Tuner power supply ON/OFF output.
23
O-CD ON
O
CD power supply ON/OFF output.
24
O-CLK
O
PLL IC clock output.
25
I-TM BASE
I
Reference clock input for timer switch.
26
O-CLOSE
O
CD tray close data output.
27
O-OPEN
O
CD tray open data output.
28
VEE
—
Power supply for FL display.
29
O-STB (DSP)
—
Not used.
30
O-K-SCAN
O
Initial scan output.
31
O.PLL_CE
O
Tuner PLL IC chip enable output.
32
NC
—
Not connected.
33
G10
O
FL grid output (G10).
34
G9
O
FL grid output (G9).
35
G8
O
FL grid output (G8).
36
G7
O
FL grid output (G7).
37
G6
O
FL grid output (G6).
38
G5
O
FL grid output (G5).
39
G4
O
FL grid output (G4).
40
G3
O
FL grid output (G3).
41
G2
O
FL grid output (G2).
Connected to GND through a resistor.
– 24 –
Pin No.
Pin Name
I/O
Description
42
G1
O
FL grid output (G1).
43
P22
—
Not used.
44
P21
—
Not used.
45
P20
O
FL segment output (P20).
46
P19
O
FL segment output (P19).
47
P18
O
FL segment output (P18).
48
P17
O
FL segment output (P17).
49
P16
O
FL segment output (P16).
50
P15
O
FL segment output (P15).
51
P14
O
FL segment output (P14).
52
P13
O
FL segment output (P13).
53
P12
O
FL segment output (P12).
54
P11
O
FL segment output (P11).
55
P10
O
FL segment output (P10).
56
P9
O
FL segment output (P9).
57
P8
O
FL segment output (P8).
58
P7
O
FL segment output (P7).
59
P6
O
FL segment output (P6).
60
P5
O
FL segment output (P5).
61
P4
O
FL segment output (P4).
62
I-TU3/P3
I/O
TU3 diode input/FL segment output (P3).
63
I-TU2/P2
I/O
TU2 diode input/FL segment output (P2).
64
I-TU1/P1
I/O
TU1 diode input/FL segment output (P1).
65
NC
—
Not connected.
66
NC
—
Not connected.
67
I-SD(V-CD)
I
CD IC control data input.
68
I/O BUSY(V-CD)
O
CD I/O BUSY line.
69
NC
I
Not connected.
70
NC
O
Not connected.
71
O-SD(V-CD)
O
CD IC control data output.
72
I-TUNE/IFC
I
Tuner SD detection input/Tuner IF count input.
73
AVSS
—
Connected to GND.
74
VREF
—
Power supply.
75
O-CLK(V-CD)
O
CD IC clock output.
76
NC
—
Connected to GND through a capacitor.
77
NC
—
Connected to GND through a capacitor.
78
NC
—
Not connected.
79
NC
—
Connected to GND through a capacitor.
80
I-TP.SW
I
Deck mechanism SW AD input.
– 25 –
IC, LC78635E
Pin No.
Pin Name
I/O
1
PDO1
O
2
PDO2
O
Description
Internal VCO control phase comparator output pin. (Pull down)
Internal VCO control phase comparator output pin.
OFF for rough servo, ON for phase servo. (Pull down)
3
VVSS
—
Internal VCO ground pin.
4
PCKIST
—
PDO output current adjustment resistor connection pin.
5
VVDD
—
Internal VCO power supply pin.
6
FR
—
VCO frequency range adjustment resistor connection pin. (Pull up)
7
HFL
I
8
SLCIST
—
SLCO output current adjustment resistor connection pin.
9
SLCO
O
Control output.
10
EFMIN
I
EFM signal input pin.
11
JITTV
O
Jitter detection monitor pin. (Not used)
12
JITTC
O
Jitter detection monitor pin. (Pull down)
13
BH
I
BH signal input pin. (Connected to GND)
14
PH (RFENV)
I
PH signal or RFENV signal input pin.
15
FE
I
FE signal input pin.
16
TE
I
TE signal input pin.
17
VREF
I
VREF input pin.
18
ADAVDD
—
Servo A/D, D/A power supply pin.
19
ADAVSS
—
Servo A/D, D/A ground pin.
20
PHREF
O
PH reference output pin. (Not used)
21
BHREF
O
BH reference output pin. (Not used)
22
TBLO
O
Tracking balance output pin.
23
TDO
O
Tracking control output pin.
24
FDO
O
Focus control output pin.
25
SPDO
O
Spindle control output pin.
26
SLDO
O
Thread control output pin.
27
FG
I/O
28
LASER
O
29
CONT1
I/O
General-purpose input/output pin 1.
30
CONT2
I/O
General-purpose input/output pin 2.
31
CONT3
I/O
General-purpose input/output pin 3.
32
CONT4
I/O
General-purpose input/output pin 4.
33
CONT5
I/O
General-purpose input/output pin 5. (Not used)
34
PCK
O
EFM data playback clock monitor pin. Average 4.3218MHz when the phase is locked. (Not used)
35
C2F
—
C2 flag output pin.
36
VDD
—
Digital power supply pin.
37
DOUT
O
Digital out output pin. (EIAJ format). (Not used)
38
FSX
O
Output pin for the 7.35kHz synchronization signal divided from the crystal oscillator. (Not used)
Mirror detection signal input pin.
Output driver VREF output pin. FG signal input pin. (Connected to GND)
Laser ON/OFF control pin.
– 26 –
Pin No.
Pin Name
I/O
Description
39
EFLG
O
C1, C2 error correction monitor pin. (Not used)
40
TEST
I
Test input pin. (Connected to GND)
41
EMPH
I/O
Emphasis pin. Which becomes an input pin after reset and can be controlled externally. This
becomes an emphasis monitor pin under control by command.
42
MUTEL
O
L channel mute output pin. (Not used)
43
MUTER
—
R channel mute output pin. (Not used)
44
LVDD
—
L channel power supply pin.
45
LCHO
I
46
LVSS
—
L channel ground pin.
47
RVSS
O
R channel ground pin.
48
RCHO
I
R channel output pin. (Not used)
49
RVDD
O
R channel power supply pin.
50
XVDD
O
Crystal oscillator power supply pin.
51
XIN
I
Connections for a 16.9344MHz crystal oscillator pin.
52
XOUT
O
Connections for a 16.9344MHz crystal oscillator pin. (Not used)
53
XVSS
I
Crystal oscillator ground pin.
54
ASLRCK
I
L/R clock input pin. (Connected to GND)
55
ASDACK
I
Bit clock input pin. (Connected to GND)
56
ASDFIN
—
L/R channel data input pin. (Connected to GND)
57
LRSY
—
L/R clock output pin.
58
DATACK
O
Bit clock output pin.
59
DATA
O
L/R channel data output pin.
60
16M
O
16.9344MHz output pin.
61
SFSY
O
L channel output pin. (Not used)
Subcode frame synchronization signal output pin. This signal falls when the subcode is in the
standby state.
62
SBSY
O
Subcode clock synchronization signal output pin. (Not used)
63
PW
O
Subcode P, Q, R, S, T, U and W output pin. (Not used)
64
SBCK
I
Subcode readout clock input pin. (Connected to GND)
65
CE
I
Chip enable signal input pin.
66
CL
I
Data transfer clock input pin.
67
DI
I
Data input pin.
68
DO
O
Data output pin.
69
INT
O
Interruption signal output pin. (Not used)
70
WRQ
O
Interruption signal output pin.
71
RES
I
Reset input pin. This pin must be set low briefly after power is first applied.
72
DRF
O
Focus ON detect pin.
73
VDD5V
—
Power Supply.
74
VSS
—
Connected to ground.
75
CONT 6
I/O
General-purpose input/output pin 6. (Not used)
76
CONT7
I/O
General-purpose input/output pin 7. (Not used)
77
V/P
O
Rough servo/phase control automatic switching monitor output pin.
“H” for rough servo and “L” for phase servo. (Not used)
– 27 –
Pin No.
Pin Name
I/O
Description
Synchronization signal detection output pin.
78
FSEQ
O
Outputs a high level when the synchronization signal detected from the EFM signal and the
internally generated synchronization signal agree.
79
DFECT
I/O
Defect pin. Which becomes an input pin after reset and can be controlled externally. This becomes
the defect monitor pin under control by command. (Not used)
80
EFMO
O
EFM signal output pin. (Not used)
– 28 –
IC, CL680-D1
Pin No.
Pin Name
I/O
1
NC
–
Not connected.
Description
2
VSS
–
GND.
3
CD BCK
I
Bit clock input from CD DSP.
4
CD DATA
I
Data input from CD DSP.
5
CD LRCK
I
LRCK input from CD DSP.
6
CD C2PO
I
C2 pointer input from CD DSP.
7~9
NC
–
Not connected.
10 ~ 15
MD0 ~ MD5
I/O
16
VSS
–
17
MD6
I/O
18
VDD3
–
19
MD7
I/O
20
VSS
–
21
MD8
I/O
22
VDD3
–
23 ~ 29
MD9 ~ MD15
I/O
30 ~ 36
NC
–
Not connected.
37
MCE
–
ROM chip enable.
38
MWE
O
DRAM write enable.
39
VSS
–
Ground.
40
CAS
O
DRAM/ROM interface.
41
VDD3
–
Power supply 3.3V.
42
RAS0
O
DRAM/ROM interface.
43
RAS1
O
DRAM/ROM interface. (Not used)
44 ~ 46
MA10 ~ MA8
O
DRAM/ROM interface. (Address)
47
VSS
–
Ground.
48
MA7
O
DRAM/ROM interface. (Address)
49
VDD3
–
Power supply 3.3V.
50 ~ 52
MA6 ~ MA4
O
DRAM/ROM interface. (Address)
53
VSS
–
Ground.
54
MA3
O
DRAM/ROM interface. (Address)
55
VDD3
–
Power supply 3.3V.
56 ~ 58
MA2 ~ MA0
O
DRAM/ROM interface. (Address)
59
PGIO7
I/O
60
RESET
I
Reset input.
61
VDD MAX IN
I
Power supply - VDDMAX. (5.0V)
62 ~ 64
NC
–
Not connected.
65
AGND DAC
–
Analog ground.
66
AVDD DAC
–
Analog power supply (DAC) : 3.3V.
67
COMPOS OUT
O
Composite out.
68
AGND DAC
–
Analog ground.
DRAM/ROM interface. (DATA)
Ground.
DRAM/ROM interface. (DATA)
Power supply 3.3V.
DRAM/ROM interface. (DATA)
Ground.
DRAM/ROM interface. (DATA)
Power supply 3.3V.
DRAM/ROM interface. (DATA)
Programmable I/O. (Not used)
– 29 –
Pin No.
Pin Name
I/O
69
YOUT
O
Video signal “Y” OUT. (Not used)
70
AVDD DAC
–
Analog power supply (DAC) 3.3V.
71
AGND DAC
–
Analog ground.
72
RREF
I
Reference resistor input.
73
VREF
I
Voltage reference input. (Not used)
74
AVDD DAC
–
Analog power supply (DAC) : 3.3V.
75
C OUT
O
Video signal “C” out. (Not used)
76
AGND DAC
–
Analog ground.
77 ~ 79
CLK SEL(0) ~ (2)
I
Clock selection input.
80
VSS
–
Ground.
81
CLK SEL(3)
I
Clock selection input.
82
VDD3
–
Power supply 3.3V.
83 ~ 84
CLK SEL(4) ~ (5)
I
Clock selection input.
85
AGND PLL
–
Analog ground.
86
DA XCK
I
DA XCK (16.933MHz) input.
87
AVDD PLL
–
Analog power supply 3.3V.
88
DA EMP
O
DAC-emphasis output.
89 ~ 90
PGIO5 ~ 6
91
PGIO0
92
PGIO8
93
VSYNC/CSYNC
O
VSYNC/CSYNC output. (Not used)
94
AVDD PLL
–
Analog power supply (PLL) 3.3V.
95
NC
–
Connected to VSS through a resistor.
96 ~ 97
NC
–
Not connected.
98
AGND PLL
–
Analog ground.
99
VSS
–
Ground.
100
NC
–
Not connected.
101
HSYNC
O
HSYNC output. (Not used)
102
VDD3
–
Power supply 3.3V.
103
VCK OUT
O
VCK out. (Not used)
104
VSS
–
Ground.
105
GCK
I
Global clock signal input. (42.3MHz) (Not used)
106
VCK IN
I
Video clock signal input. (27.0MHz)
107
GCK OUT
O
Global clock signal output. (27.0MHz) (Not used)
108
DA LRCK
O
DAC-LRCK output.
109
VDD MAX OUT
–
Power supply (VDD MAX) : 5.0V.
110
DA DATA
O
DAC-PCM data output.
111
DA BCK
O
DAC-BIT clock output.
112
HD OUT
O
Micon interface. (Data out)
113
HRDY
O
Micon interface. (Host ready)
114
HINT
O
Micon interface. (Host interrupt)
I/O
Description
Programmable I/O. (Not used)
– 30 –
Pin No.
Pin Name
I/O
Description
115
CDG SCK
I
CD-G serial clock input.
116
VSS
–
Ground.
117
HCK
I
Micon interface. (Host clock)
118
VDD3
–
Power supply 3.3V.
119
HD-IN
I
Micon interface. (Host data in)
120
VDD3
–
Power supply 3.3V.
121
HSEL
I
Micon interface. (Host select in)
122
CDG SDATA
I
CD-G data input. (Not used)
123
CDG VFSY
I
CD-G VFSY input. (Not used)
124
CDG SOSI
I
CD-G SOSI input.
125 ~ 128
NC
–
Not connected.
IC, µPD78016FGC-574-AB8
Pin No.
Pin Name
I/O
Description
1
NC
–
Not connected.
2
AMUTE
O
Audio analog mute ("H" = Mute ON).
Synchronization signal detection input pin.
3
FSEQ
I
Inputs a high level when the synchronization signal detected from the EFM signal and the
internally generated synchronization signal agree. (Not used)
4
NC
–
Not connected.
5
NC
–
Not connected.
6
EMPH
I
Emphasis input terminal.
7
DATA IN
I
Data input pin.
8
NC
–
Not connected.
9
VSS
–
GND.
10~12
NC
–
Connected to GND.
13
EMERG
I
Power emergency stop (L*3sec = STOP).
14 ~ 19
NC
–
Not connected.
20
XCDRST
O
CD reset output terminal.
21
CMND
O
DATA output pin.
22
CE
O
Chip enable signal output pin.
23
CL
O
Data transfer clock output pin.
24
VSS
–
GND.
25
DRF
I
Focus ON detect pin.
26
WRQ
I
Interruption signal input pin.
27
XBUSY
I/O
28 ~ 30
NC
–
31 ~ 34
TST0 ~ TST3
I/O
35
RESET
I
READY/BUSY I/O to HOST OD.
Not connected.
Check Land. (Not used)
Reset.
– 31 –
Pin No.
Pin Name
I/O
Description
36
HRDY
I
HRDY from CL680.
37
XHINT
I
HINT from CL680
38
NC
–
Not connected.
39
SCOR
I
SCOR from CD.
40
VDD
–
5.0VDD.
41
XO
O
42
XI
I
43
VSS
–
GND.
44
XT2
–
Not used.
45
XT1
I
Connected to VDD.
46
AVSS
–
GND.
47
XMPGRST
O
MPEG block IC reset.
48
HSEL
O
Address/Data SEL to CL680.
49
NC
–
Not connected.
50
NT/PAL
–
NTSC/PAL mode select.
51
OSDXCS
O
OSD chip select.
52
NC
–
Connected to GND.
53
CLVSEL
I
CLV mode select ("H" = CLV-N). (Not used)
54
AADSEL
I
Auto adjust select ("H" = Auto ON). (Not used)
55
AVDD
–
5.0VDD.
56
AVREF
57
HDOUT
I
HD-OUT from CL680.
58
HDIN
O
HD-IN to CL680.
59
HCK
O
HCK to CL680.
60
OSDDATA
O
OSD data.
61
OSDCLK
O
OSD clock.
62
COMMAND
I
COMMAND from host.
63
STATUS
O
STATUS to host.
64
SCK
I
SCK from host.
8.0MHz ceralock.
– 32 –
ADJUSTMENT <TUNER / DECK / FRONT>
< TUNER SECTION >
1. Clock Frequency Check
Settings : • Test point : TP2 (CLK)
Method : Set to AM 1710kHz and check that the test point is
2160kHz ± 45Hz.
2. AM VT Check
Settings : • Test point : TP1 (VT)
Method : Set to AM 1710kHz, 530kHz and check that the test
point is less than 8.5V (1710kHz) and more than
0.6V (530kHz).
3. FM VT Adjustment
Settings : • Test point : TP1 (VT)
• Adjustment location : L907
Method : Set to FM 108.0MHz and adjust L907 so that the test
point is 7.0V ± 50mV.
4. AM Tracking Adjustment
Settings : • Test point : TP5 (Lch), TP6 (Rch)
• Adjustment location :
L951(1/3) ........................................ 999kHz
Method : Set to AM 1000kHz and adjust L951(1/3) to MAX.
5. FM Tracking Adjustment
Settings : • Test point : TP5 (Lch), TP6 (Rch)
• Adjustment location : L904
Method : Set to FM 87.5MHz and adjust L904 so that the test
point is maximum.
6. AM IF Adjustment
Settings : • Test point : TP5 (Lch), TP6 (Rch)
• Adjustment location :
L802 ................................................ 450kHz
3. PB Frequency Response Check (DECK 1, DECK 2)
Settings : • Test tape : TTA–330
• Test point :TP5 (Lch), TP6 (Rch)
Method : Play back the 315Hz and 8kHz signals of the test
tape and check that the output ratio of the 8kHz
signal with respect to that of the 315Hz signal is
0dB ± 4dB.
4. REC/PB Frequency Response Check (DECK 1)
Settings : • Test tape : TTA–602
• Test point : TP5 (Lch), TP6 (Rch)
Method : Apply a 1kHz signal and REC mode. Then adjust
OSC attenuator so that the output level at the TP5,
TP6 becomes 80mV. Record and play back the 1kHz
and 8kHz signal and check that the output of the 8kHz
signals is 0dB ± 5dB with respsct to that of the 1 kHz
signal.
5. REC/PB Sensitivity Check (DECK 1)
Settings : • Test tape : TTA–602
• Test point : TP5 (Lch), TP6 (Rch)
• Input signal : 1kHz (LINE IN)
Method : Apply a 1kHz signal and REC mode. Then adjust
OSC attenuator so that the output level at TP5, TP6
becomes 8mV. Record and play back the 1kHz signals
and check that the output is –2dB ± 3.5dB.
6. PB Sensitivity Check (DECK 1, Deck 2)
Settings : • Test tape : TTA–200
• Test point :TP5 (Lch), TP6 (Rch)
Method : Play back the test tape and check that the output level of
the test point is 110mV ± 3.5dB.
< FRONT SECTION >
7. DC Balance / Mono Distortion Adjustment
Settings : • Test point : TP3, TP4 (DC Balance)
: TP5 (Lch), TP6 (Rch) (Distortion)
• Adjustment location : L801
• Input level : 60dBµV
Method : Set to FM 98.0MHz and adjust L801 so that the
voltage between TP3 and TP4 is 0V ± 0.04V.
Then check the distortion is less than 1.3%
1. µ-CON OSC Adjustment
Settings : • Test point : TP7 and TP8 (GND)
• Adjustment location : L501
Method : Insert AC plug while pressing TUNER function key.
Adjust L501 so that the frequency at the test point is
233.4Hz ± 0.23Hz.
< DECK SECTION >
1. Tape Speed Adjustment (DECK 1)
Settings : • Test tape : TTA–100
• Test point : TP5 (Lch), TP6 (Rch)
• Adjustment location : SFR501
Method : Play back the test tape and adjust SFR501 so that the
frequency counter reads 3000Hz ± 5Hz (FWD) and
± 45Hz (REV) with respect to forward speed.
2. Head Azimuth Adjustment (DECK 1, DECK 2)
Settings : • Test tape : TTA–330
• Test point : TP5 (Lch), TP6 (Rch)
• Adjustment location : Head azimuth
adjustment screw
Method : Play back (FWD) the 8kHz signal of the test tape
and adjust screw so that the output becomes maximum.
Next, perform on REV PLAY mode.
– 33 –
CD TEST MODE
– 34 –
MECHANICAL EXPLODED VIEW 1 / 1
B
B
22
24
32
B
B
C
B
B
B
B
B
B
H
3ZG-3
20
B
B
B
C
P.W.B
C
PWB,HLDR FFC
B
a
B
A
21
11
A
31
23
16
FL
B
26
28
D
19
B
PWB,HLDR WIRE
C
10
P.W.B
b
G
E
P.W.B
E
17
18
B
B
13
B
B
ZZM-2
B
HT-SINK,TR LOW
C
6
7
4
14
B
B
HT-SINK,FIN
B
F
B
9
B
b
B
B
5
29
B
12
a
15
27
3
B
1
29
30
2
C
B
B
8
3
25
– 35 –
CX-NVC8 HRJSM
(File Name:EXP.EPS)
12/9/22 ANH-C
MECHANICAL PARTS LIST 1 / 1
REF. NO. PART NO.
!
1
2
3
4
5
8A-NEC-006-010
8A-NEC-007-010
82-NF7-218-010
8A-NEC-002-010
8A-NEC-003-010
6
7
8
9
10
8A-NHC-002-010
87-CE3-023-010
86-NFZ-231-010
8Z-NF8-028-110
8A-NHC-005-010
11
12
13
14
15
16
17
18
19
20
REF. NO. PART NO.
KANRI
DESCRIPTION
NO.
WINDOW,CASS 1
WINDOW,CASS 2
SPR-T,CASS
BOX,CASS 1
BOX,CASS 2
KANRI
DESCRIPTION
NO.
HLDR,CD R
PANEL,TOP
PANEL,LEFT
CABI,REAR HRJ VCD
CABI,BOTTOM VCD
21
22
23
24
25
8A-NEC-204-010
8A-NEC-015-010
8A-NEC-013-010
8A-NHC-003-010
8A-NHC-210-010
WINDOW,DISP HR VCD
BADGE,AIWA 30N SILV
DMPR,70
KNOB,RTRY MIC
CABI,FR HR VCD
26
27
28
29
30
8A-NEC-201-110
8A-NEC-014-010
8A-NHC-202-010
8A-NHC-206-010
87-A91-751-010
HLDR,PT
PANEL,RIGHT
HLDR,VCD
HLDR,FAN
FAN,DSB0812M-S382 -400MM
8A-NHC-001-010
87-A80-157-010
8A-NEC-041-010
8A-NEC-010-010
8A-NEC-011-010
KEY,POWER VCD
AC CORD ASSY,E BLK CC
PLATE,MIC
KEY,CASS 1
KEY,CASS 2
31
32
A
B
C
8A-NHC-201-010
8A-NHC-203-010
87-067-822-010
87-067-703-010
87-067-641-010
COVER, VCD BOTTOM
COVER, VCD TOP
BVT2+3-20 W/O SLOT
TAPPING SCREW, BVT2+3-10
UTT2+3-8(W/O SLOT)BL
8A-NFA-208-010
8A-NEC-009-010
8A-NEC-206-010
8A-NEC-004-010
8A-NEC-203-010
GUIDE,FL 100-25 ANFA
KEY,OPEN/CLOSE
HLDR,DECK
PANEL,TRAY CD
HLDR,CD L
D
E
F
G
H
87-571-092-410
87-067-975-010
87-067-001-010
87-067-579-010
87-067-584-010
TAPPING SCREW, VIT+3-4
S-SCREW,IT+4-8
S-SCREW,BVWWST2+3-12 W/O SLOT
TAPPING SCREW, BVT2+3-8
TAPPING SCREW, BVT2+3-6
COLOR NAME TABLE
Basic color symbol
Color
Basic color symbol
Color
Basic color symbol
Color
B
Black
C
Cream
D
Orange
G
Green
H
Gray
L
Blue
LT
Transparent Blue
N
Gold
P
Pink
R
Red
S
Silver
ST
Titan Silver
T
Brown
V
Violet
W
White
WT
Transparent White
Y
Yellow
YT
Transparent Yellow
LM
Metallic Blue
LL
Light Blue
GT
Transparent Green
LD
Dark Blue
DT
Transparent Orange
GM
Metallic Green
YM
Metallic Yellow
DM
Metallic Orange
PT
Transparent Pink
LA
Aqua Blue
– 36 –
TAPE MECHANISM EXPLODED VIEW 1 / 1
TERMINAL,LB1 A
54
4
22
14
15
3
6
22
20
23
21
27
20
5
2
23
21
28
13
19
TERMINAL,LB1 A
55
18
14
17
1
25
29
6
5
13
59
24
54
b
15
26
55
a
31
19
16
28
18
61
59
17
16
B
53
46
30
47
27
38
45
33
37
43
26
24
44
29
25
34
b
1
12
51
a
11
12
40
53
32
33
52
10
4
51
11
3
34
47
1
36
9
39
8
7
57
58
2
37
46
50
35
45
1
10
56
44
9
49
43
48
8
7
57
41
42
38
40
60
58
39
– 37 –
TAPE MECHANISM PARTS LIST 1 / 1
36
37
38
39
40
8Z-ZM1-220-110
8Z-ZM1-249-210
8Z-ZM1-242-310
8Z-ZM3-244-110
8Z-ZM1-232-010
KANRI
DESCRIPTION
NO.
LEVER,REC SENSOR
SPR-T,FR
SPR-T,FF/REW
GEAR,CAM TD20
GEAR,IDL FF/REW
SPR-T,AUTO
CLR,SLIP FF/REW
SPR-C,FF/REW
GEAR,SLIP FR A ZZM-2
FELT,FF/REW 2
41
42
43
44
45
8Z-ZM3-228-110
8Z-ZM2-601-010
8Z-ZM1-228-010
8Z-ZM1-265-010
8Z-ZM1-227-010
FLY-WHL,M3
CONN ASSY,9P ZZM-2
GEAR,SLIP T-UP B
FELT,T-UP
GEAR,SLIP T-UP A
8Z-ZM1-238-110
8Z-ZM1-237-110
8Z-ZM1-209-510
8Z-ZM1-218-210
8Z-ZM1-256-010
GEAR,SLIP FF/REW B 2
LEVER,FF/REW 2
LEVER,PAUSE
LEVER,E-LOCK H
SPR-P,PAUSE
46
47
48
49
50
8Z-ZM1-251-210
8Z-ZM1-243-310
87-A91-532-010
8Z-ZM1-235-010
8Z-ZM2-216-010
SPR-C,T-UP SLIP
SPR-T,STOP/PAUSE
MOT,MS15U2LW1A
PULLEY,MOT
BELT,MAIN M
16
17
18
19
20
8Z-ZM1-244-110
8Z-ZM1-247-310
8Z-ZM1-261-110
8Z-ZM1-221-210
8Z-ZM1-205-310
SPR-T,T-UP
SPR-T,PINCH
ROLLER ASSY,PINCH
LEVER,PINCH
LEVER,PLAY
51
52
53
54
55
8Z-ZM1-260-010
8Z-ZM2-201-510
8Z-ZM1-255-310
8Z-ZM2-219-010
8Z-ZM1-214-310
SPR-P,CASETTE
CHAS ASSY,ZZM-2
SPR-T,E-LOCK
LEVER,E-OPEN ZZM-2
LEVER,LOCK
21
22
23
24
25
8Z-ZM1-248-210
87-A90-403-110
84-ZM2-227-310
8Z-ZM1-216-110
8Z-ZM1-246-110
SPR-T,BRG
HEAD,RPH MS15R
SPR-C,AZIMUTH
LEVER,AUTO
SPR-T,AUTO 2
56
57
58
59
60
8Z-ZM2-211-210
8Z-ZM1-257-110
8Z-ZM1-275-010
87-B10-301-010
87-A91-494-010
FLY-WHL,ZZM-2
SPR-C,F/R
W-L,1.47-4-0.25
W-L,1.63-3.2-0.5 SLIT
SW,LEAF MSW17820
26
27
28
29
30
8Z-ZM2-214-110
8Z-ZM2-212-010
8Z-ZM1-207-010
8Z-ZM1-206-010
8Z-ZM1-210-010
GEAR,IDL REW ZZM-2
LEVER,STOP ZZM-2
LEVER,FF
LEVER,REW
LEVER,REC
61
A
B
8Z-ZM1-241-010
84-ZM2-242-010
8Z-ZM2-220-110
SPR-T,PLAY
S-SCREW,AZ1-2-6.4
V+2.6 ZZM-2
31
32
33
34
35
87-A90-404-010
8Z-ZM2-218-010
87-A91-492-010
8Z-ZM1-226-010
8Z-ZM1-241-210
HEAD,EH LE15B
LEVER,REC LOCK ZZM-2
SW,LEAF MSW18560
GEAR,REEL L
SPR-T,PLAY
REF. NO. PART NO.
1
2
3
4
5
8Z-ZM1-254-310
8Z-ZM1-225-110
8Z-ZM1-253-210
8Z-ZM1-217-110
8Z-ZM1-212-210
6
7
8
9
10
8Z-ZM1-245-310
8Z-ZM1-236-010
8Z-ZM1-252-110
8Z-ZM2-213-010
8Z-ZM1-269-010
11
12
13
14
15
REF. NO. PART NO.
KANRI
DESCRIPTION
NO.
SPR-C,REEL R
GEAR,REEL R
SPR-C,AUTO SENSOR
LEVER,AUTO SENSOR
LEVER,T-UP
– 38 –
CD MECHANISM EXPLODED VIEW 1 / 2 (3ZG-3 E8NM)
9
F
CUSH-G,
MAIN
C
F
13
CUSH-G,
MAIN
14
a
3ZG-2 E3
15
b
11
5
10
7
E
8
4
B
6
2
D
a
12
3
A
(M1)
MOT
LOADING
MOTOR
PWB
b
– 39 –
1
CD MECHANISM PARTS LIST 1 / 2 (3ZG-3 E8NM)
REF. NO. PART NO.
1
2
3
4
5
83-ZG3-224-519
83-ZG3-228-619
83-ZG3-208-019
83-ZG3-213-019
83-ZG3-209-619
KANRI
DESCRIPTION
NO.
1B HLDR M2
1C CHAS,L6
0E PULLEY,MOTOR
0E LVR,SW
1A CAM,SLIDE
6
7
8
9
10
83-ZG3-207-619
83-ZG3-204-21M
83-ZG3-205-019
83-ZG3-211-01K
83-ZG3-220-21M
0E
0E
0E
0E
0E
GEAR,TRAY
GEAR,C
GEAR,D
PLATE,DISC
GEAR,PULLEY 2
11
12
13
14
15
83-ZG3-214-019
83-ZG3-229-51K
83-ZG3-210-119
83-ZG3-604-010
83-ZG3-212-019
0E
1C
1B
0E
0E
BELT,L
TRAY,CD 2
HLDR,CHUCK
RING,MAG 2
CAP,DISC
– 40 –
A
B
C
D
E
87-067-945-119
87-251-071-410
83-ZG3-235-010
87-352-075-219
83-ZG3-217-019
0E
0E
0E
0E
0E
VFT2+3-12(F10)
U+2.6-4
VFT2+2.6-8
VT2+2.6-10
S-SCREW,GEAR D
F
81-ZG1-254-019 0E S-SCREW,MECH HLDR
CD MECHANISM EXPLODED VIEW 2 / 2 (3ZG-2 E3NM)
2
3
1
A
4
M21
6
SW1
5
PWB
CD MECHANISM PARTS LIST 2 / 2 (3ZG-2 E3NM)
REF. NO. PART NO.
1
2
3
4
5
83-ZG2-262-010
87-A90-836-010
83-ZG2-235-010
83-ZG2-236-010
83-ZG2-205-310
6
A
83-ZG2-253-010
87-261-032-210
KANRI
DESCRIPTION
NO.
CHAS ASSY,E3
PICKUP,KSS-213F
GEAR,A3
GEAR,MOTOR 3
GEAR,B
SHAFT,SLIDE 5
V+2-3
– 41 –
GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE)
Type.1
Type.4
TOOLS
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Remove the screws of each speaker
unit and then remove the speaker units.
1 Plastic head hammer
2 (() flat head screwdriver
3 Cut chisel
1
2
3
How to Remove the PANEL, FR
Type.2
Remove the grill frame and four pieces of rubber caps by pulling
out with a flat-bladed screwdriver. Remove the screws from hole
where installed rubber caps. Insert a flat-bladed screwdriver into
the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker
units.
1.
Insert the (() flat head screwdriver tip into the gap
between the PANEL, FR and the PANEL, SPKR. Tap the
head of the (() flat head screwdriver with the plastic
hammer head, and create the clearance as shown in Fig-1.
2.
Insert the cut chisel in the clearance, and tap the head of
the cut chisel with plastic hammer as shown in Fig-2, to
remove the PANEL, FR.
3.
Place the speaker horizontally. Tap head of the cut chisel
with plastic hammer as shown in Fig-3, and remove the
PANEL, FR completely.
Type.3
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Turn the speaker unit to counterclockwise direction while inserting a flat-bladed screwdriver into
one of the hollows around speaker unit, and then remove the speaker
unit. After replacing the speaker unit, install it turning to clockwise
direction until "click" sound comes out.
Fig-1
Fig-2
Fig-3
How to Attach the PANEL, FR
Attach the PANEL, FR to the PANEL, SPKR. Tap the four
corners of the PANEL, FR with the plastic hammer to fit the
PANEL, FR into the PANEL, SPKR completely.
– 42 –
SPEAKER PARTS LIST (SX-NVC8) <YJSL, YJ3SL, YJSK2BL>
REF. NO. PART NO.
1
2
3
4
4
8A-NSM-020-010
8A-NSM-008-010
8Z-NSY-003-010
8A-NSM-604-010
8A-NSM-606-010
KANRI
DESCRIPTION
NO.
GRILLE, FRAME ASSY L
CORD, SPKR
CORD, BUSH<YJSK2BL>
SPKR, 100<YJSL,YJ3SL>
SPKR, 100<YJSK2BL>
ACCESSORIES / PACKAGE LIST
REF. NO. PART NO.
!
1
2
3
4
5
KANRI
DESCRIPTION
NO.
8A-NHC-901-010
IB,H(ECA)M
8A-NHC-701-010
RC UNIT,RC-AAS09
87-043-115-010
ANT,FEEDER FM
87-006-225-010
ANT,LOOP ANT NC 2
87-A91-017-010
PLUG,CONVERSION JT-0476
– 43 –
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
2000058 0251431
Printed in Singapore