Bosch DLE 40 Professional Operating instructions

OBJ_BUCH-703-002.book Page 1 Wednesday, July 23, 2008 7:21 PM
:07
5-1 m
82 n
60, 635
IECmW
<1
lic
g lb
lun rah
rah St
rst en
se d e 2
La ht in lass
nic er K
s
La
Robert Bosch GmbH
Geschäftsbereich Elektrowerkzeuge
D-70745 Leinfelden-Echterdingen
Germany
n
ke
DLE 70 Professional
www.bosch-pt.com
1 609 929 R53 (2008.07) T / 342 XXX
de
en
fr
es
pt
it
nl
Originalbetriebsanleitung
Original instructions
Notice originale
Manual original
Manual original
Istruzioni originali
Oorspronkelijke
gebruiksaanwijzing
da Original brugsanvisning
sv Bruksanvisning i original
no Original driftsinstruks
fi Alkuperäiset ohjeet
el Πρωτότυπο οδηγιών χρήσης
tr Orijinal işletme talimat
pl
cs
sk
hu
ru
Instrukcją oryginalną
Původním návodem k používání
Pôvodný návod na použitie
Eredeti használati utasítás
Оригинальное руководство по
эксплуатации
uk Оригінальна інструкція з
експлуатації
ro Instrucţiuni de folosire originale
bg Оригинално ръководство за
експлоатация
sr Originalno uputstvo za rad
sl Izvirna navodila
hr
et
lv
lt
cn
tw
ko
ar
fa
Originalne upute za rad
Algupärane kasutusjuhend
Oriģinālā lietošanas pamācība
Originali instrukcija
正本使用说明书
正本使用說明書
사용 설명서 원본
ΔϴϠλϷ΍ ϞϴϐθΘϟ΍ ΕΎϤϴϠόΗ
̶Ϡλ΍ έΎ̯ ίήσ ̵ΎϤϨϫ΍έ
OBJ_BUCH-703-002.book Page 2 Wednesday, July 23, 2008 3:15 PM
2|
Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seite
7
English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page
18
Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page
30
Español. . . . . . . . . . . . . . . . . . . . . . . . . . . . Página
41
Português . . . . . . . . . . . . . . . . . . . . . . . . . . Página
52
Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pagina
63
Nederlands . . . . . . . . . . . . . . . . . . . . . . . . . Pagina
75
Dansk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Side
86
Svenska . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sida
96
Norsk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Side 106
Suomi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sivu 116
Ελληνικά . . . . . . . . . . . . . . . . . . . . . . . . . . . Σελίδα 126
Türkçe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sayfa 137
Polski . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Strona 147
Česky . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Strana 158
Slovensky . . . . . . . . . . . . . . . . . . . . . . . . . . Strana 168
Magyar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oldal 179
Русский . . . . . . . . . . . . . . . . . . . . . . . . Страница 190
Українська . . . . . . . . . . . . . . . . . . . . . . . Сторінка 202
Română . . . . . . . . . . . . . . . . . . . . . . . . . . . Pagina 213
Български . . . . . . . . . . . . . . . . . . . . . . Страница 224
Srpski . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Strana 235
Slovensko . . . . . . . . . . . . . . . . . . . . . . . . . . . Stran 245
Hrvatski . . . . . . . . . . . . . . . . . . . . . . . . . Stranica 255
Eesti . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lehekülg 265
Latviešu . . . . . . . . . . . . . . . . . . . . . . . . . Lappuse 275
Lietuviškai . . . . . . . . . . . . . . . . . . . . . . . Puslapis 286
中文 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 页 296
中文 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 頁 305
한국어 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .면 314
vc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
vÝ—U . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 609 929 R53 | (23.7.08)
ΔΤϔλ 323
ϪΤϔλ 332
Bosch Power Tools
OBJ_BUCH-703-002.book Page 3 Wednesday, July 23, 2008 3:15 PM
3|
a
b
c
d
e
i
i
i
h
g
e
f
7
8
1
2
3
4
5
6
:07
5-1 m
82 n
60, 635
IECmW
<1
en
ck
g l bli
lun rah
rah St
rst en
se d e 2
La ht in lass
nic er K
s
La
16
9
8
14
13
12
11
10
15
1 609 929 R53 | (23.7.08)
Bosch Power Tools
OBJ_BUCH-703-002.book Page 4 Wednesday, July 23, 2008 3:15 PM
4|
A
18
17
bli
g
lun hl
ah Stra
rstr n
se de 2
La ht in sse
la
nic er K
s
La
19
ck
:07
5-1
82 nm
60 635
IECmW,
<1
en
20
22
21
B
C
D
E
1 609 929 R53 | (23.7.08)
Bosch Power Tools
OBJ_BUCH-703-002.book Page 5 Wednesday, July 23, 2008 3:15 PM
5|
F
G
H
I
B1
A
C
B
B3
B2
A
J
K
0,5
m
5m
2,4
1 609 929 R53 | (23.7.08)
Bosch Power Tools
OBJ_BUCH-703-002.book Page 6 Wednesday, July 23, 2008 3:15 PM
6|
24
2 607 990 031
25
2 607 001 391
23
BS 150
0 601 096 974
al
70 n
E sio
DL fes
o
Pr
26
1 609 203 R97
27
1 609 203 X26
19
1 609 203 X36
15
1 609 203 X48
1 609 929 R53 | (23.7.08)
Bosch Power Tools
OBJ_BUCH-703-002.book Page 18 Wednesday, July 23, 2008 3:15 PM
18 | English
Safety Notes
en
Working safely with the measuring
tool is possible only when the operating and safety information are
read completely and the instructions contained therein are strictly
followed. Never make warning labels on the
measuring tool unrecognisable. SAVE THESE
INSTRUCTIONS.
f Caution – The use of other operating or
adjusting equipment or the application of
other processing methods than those
mentioned here, can lead to dangerous
radiation exposure.
f The measuring tool is delivered with a warning label in German language (marked with
the number 9 in the representation of the
measuring tool on the graphic page).
IEC 60825-1:07
<1 mW, 635 nm
f Do not use the laser viewing glasses as safety goggles. The laser viewing glasses are
used for improved visualisation of the laser
beam, but they do not protect against laser
radiation.
f Do not use the laser viewing glasses as sun
glasses or in traffic. The laser viewing glasses do not afford complete UV protection and
reduce colour perception.
f Have the measuring tool repaired only
through qualified specialists using original
spare parts. This ensures that the safety of
the measuring tool is maintained.
f Do not allow children to use the laser measuring tool without supervision. They could
unintentionally blind other persons or themselves.
f Keep the positioning pin 15 away from
“live” wires or parts. There is a risk of electric shock.
Functional Description
Please unfold the fold-out page with the representation of the measuring tool and leave it unfolded while reading the operating instructions.
Intended Use
f Before putting into operation for the first
time, attach the supplied sticker in your
national language over the German text on
the warning label.
f Do not direct the laser beam at persons or
animals and do not stare into the laser beam
yourself. This measuring tool produces
laser class 2 laser radiation according to
IEC 60825-1. This can lead to persons being
blinded.
1 609 929 R53 | (23.7.08)
The measuring tool is intended for measuring
distances, lengths, heights, clearances and for
calculating areas and volumes. The measuring
tool is suitable for interior and exterior construction site measuring.
Bosch Power Tools
OBJ_BUCH-703-002.book Page 19 Wednesday, July 23, 2008 3:15 PM
English | 19
Technical Data
Digital Laser Rangefinder
DLE 70
Professional
3 601 K16 60.
Article number
0.05 – 70 m A)
Measuring range
± 1.5 mm B)
Measuring accuracy (typically)
Lowest indication unit
1 mm
– 10 °C...+50 °C C)
Operating temperature
– 20 °C...+70 °C
Storage temperature
90 %
Relative air humidity, max.
Laser class
2
Laser type
635 nm, <1 mW
Laser beam diameter (at 25 °C) approx.
– at 10 m distance
– at 70 m distance
6 mm
42 mm
4 x 1.5 V LR03 (AAA)
4 x 1.2 V KR03 (AAA)
Batteries
Rechargeable batteries
Battery live, approximately
– Individual measurements
– Continuous measurement
30000 D)
5 h D)
Automatic switch-off after approx.
– Laser
– Measuring tool (without measurement)
20 s
5 min
0.18 kg
Weight according to EPTA-Procedure 01/2003
59 x 100 x 32 mm
Dimensions
Degree of protection (excluding battery compartment)
IP 54 (dust and splash water protected)
A) The working range increases depending on how well the laser light is reflected from the surface of the target (scattered, not reflective) and with increased brightness of the laser point to the ambient light intensity (interior spaces,
twilight). In unfavourable conditions (e.g. when measuring outdoors at intense sunlight), it may be necessary to use
the target plate.
B) In unfavourable conditions (e.g. when measuring outdoors at intense sunlight or an insufficiently reflecting surface), the maximum deviation is ± 10 mm per 70 m. In favourable conditions, a deviation influence of ± 0.05 mm/m
must be taken into account.
C) In the continuous measurement function, the maximum operating temperature is +40 °C.
D) Fewer measurements are possible when using 1.2 V rechargeable batteries as compared with 1.5 V batteries.
Please observe the article number on the type plate of your measuring tool. The trade names of the individual measuring tools may vary.
The measuring tool can be clearly identified with the serial number 20 on the type plate.
Bosch Power Tools
1 609 929 R53 | (23.7.08)
OBJ_BUCH-703-002.book Page 20 Wednesday, July 23, 2008 3:15 PM
20 | English
Product Features
The numbering of the product features shown
refers to the illustration of the measuring tool
on the graphic page.
1 Reference level button
2 Memory retrieve button “M=”
3 Memory add button “M+”
4 Button for minimum and maximum
measurement
5 Button for length, area and volume
measurement
6 Spirit level
7 Display
8 Alignment aid
9 Laser warning label
10 Button for measuring and continuous
measuring
11 Button for indirect length measurement and
measurement of wall surfaces
12 Memory subtraction button “M– ”
13 Button for continuous laser beam
Display Elements
a
b
c
d
e
f
g
h
Measured values stored
Battery indication
Temperature indicator
Measured value/result
Unit of measure
Measurement reference level
Laser switched on
Individual measured value (for length
measurement: result)
i Measuring functions
Length measurement
Area/surface measurement
Volume measurement
Indirect length measurement
Wall surface measurement
Continuous measurement
MIN Minimum measurement
MAX Maximum measurement
Assembly
14 On/Off and memory delete button
Inserting/Replacing the Battery
15 Positioning pin
Use only alkali-manganese or rechargeable
batteries.
Fewer measurements are possible when using
1.2 V rechargeable batteries as compared with
1.5 V batteries.
To open the battery lid 19, press the latch 18 in
the direction of the arrow and remove the battery lid. Insert the batteries provided. Pay attention to the correct polarity of the batteries
according to the representation in the battery
compartment.
When the
battery symbol appears in the display for the first time, then at least 100 measurements are still possible. The batteries must be
replaced when the battery symbol flashes;
taking measurements is no longer possible.
Always replace all batteries at the same time.
Only use batteries from one brand and with the
identical capacity.
f Remove the batteries from the measuring
tool when not using it for extended periods.
When storing for extended periods, the batteries can corrode and discharge themselves.
16 Latch of the positioning pin
17 1/4" thread
18 Latch of battery lid
19 Battery lid
20 Serial number
21 Laser beam outlet
22 Reception lens
23 Tripod*
24 Laser viewing glasses*
25 Laser target plate*
26 Carrying strap
27 Protective case
*The accessories illustrated or described are not
included as standard delivery.
1 609 929 R53 | (23.7.08)
Bosch Power Tools
OBJ_BUCH-703-002.book Page 21 Wednesday, July 23, 2008 3:15 PM
English | 21
Operation
Initial Operation
f Protect the measuring tool against moisture and direct sun irradiation.
f Do not expose the measuring tool to
extreme temperatures or variations in
temperature.
Switching On and Off
To switch on the measuring tool, briefly press
the On/Off button 14 or measuring button 10.
When switching on the measuring tool, the laser
beam is not switched on yet.
To switch off the measuring tool, press the
On/Off button 14 for a few seconds.
If none of the measuring tool buttons are
pressed for approx. 5 minutes, the measuring
tool switches off automatically in order to
extend the service life of the battery.
When a measured value has been stored, it is
retained in automatic switch-off mode. When
switching on the measuring tool again, “M” is
indicated in the display.
Measuring Procedure
After switching on, the measuring tool is in the
length measurement mode. Other measuring
modes can be switched to by pressing the respective function/mode button (see “Measuring
Functions”, page 22).
After switching on, the rear edge of the measuring tool is preset as the reference level for the
measurement. By pressing the reference level
button 1, the reference level can be changed
(see “Selecting the Reference Level”, page 21).
Upon selection of the measuring function and
the reference level, all further steps are carried
out by pushing the measuring button 10.
With the reference level selected, place the
measuring tool against the desired measuring
line (e.g. a wall).
Briefly press the measuring button 10 to switch
on the laser beam.
Bosch Power Tools
f Do not point the laser beam at persons or
animals and do not look into the laser beam
yourself, not even from a large distance.
Aim the laser beam at the target surface. Briefly
press the measuring button 10 again to initate
the measurement.
When the laser beam is switched on permanently and in the minimum and maximum measurement modes, the measurement already starts
upon first actuation of the measuring button 10.
In the continuous measurement mode, the
measurement starts immediately upon switching on the function.
Typically, the measured value appears after 0.5
and latest after 4 seconds. The duration of the
measurement depends on the distance, the light
conditions and the reflection properties of the
target surface. The end of the measurement is
indicated by a signal tone. The laser beam is
switched off automatically upon completion of
the measurement.
When no measurement has taken place approx.
20 seconds after sighting, the laser beam is
switched off automatically to save the batteries.
Selecting the Reference Level
(see figures B – E)
For measuring, it is possible to select from four
different reference levels:
– the rear edge of the measuring tool
(e.g., when placing the measuring tool flush
against a wall),
– the rear edge of the positioning pin 15
(e.g., for measurements out of corners).
– the front edge of the measuring tool (e.g., as
when measuring from the edge of a table
onward),
– the thread 17 (e.g., for measuring with the
tripod).
To select the reference level, push button 1
repeatedly until the required reference level is
indicated in the display. Each time after switching on, the rear edge of the measuring tool is
preset as the reference level.
1 609 929 R53 | (23.7.08)
OBJ_BUCH-703-002.book Page 22 Wednesday, July 23, 2008 3:15 PM
22 | English
Continuous Laser Beam
If required, the measuring tool can also be
switched to the continuous laser beam mode. For
this, push the button for continuous laser beam
13. “LASER” lights up continuously in the display.
f Do not point the laser beam at persons or
animals and do not look into the laser beam
yourself, not even from a large distance.
In this setting, the laser beam also remains
switched on between measurements; for measuring, it is only required to press the measuring
button 10 once.
To switch off the continuous laser beam, press
button 13 again or switch the measuring tool
off. When switching on again, the measuring
tool is in the standard operation mode and the
laser beam appears only after pushing the measuring button 10.
Measuring Functions
Length Measurement
For length measurements, press button 5 until
the indicator for length measurement
appears
in the display.
Press the measuring button 10 once for sighting
and once more to take the
measurement.
The measured value is indicated at the bottom in the
display.
Area Measurement
For area/surface measurements, press button 5
until the indicator for area measurement
appears in the display.
Afterwards, measure the length and the width,
one after another, in the same manner as a
length measurement. The laser beam remains
switched on between both measurements.
After taking the second
measurement, the area/
surface is automatically
calculated and displayed.
The last individual measured value is indicated at
the bottom in the display, while the final result
is shown at the top.
1 609 929 R53 | (23.7.08)
Volume Measurement
For volume measurements, press button 5 until
the indicator for volume measurement
appears in the display.
Afterwards, measure the length, width and the
height, one after another, in the same manner as
for a length measurement. The laser beam remains
switched on between all three measurements.
After taking the third measurement, the volume is automatically calculated and
displayed. The last individual measured value is indicated at the bottom in the
display, while the final result is shown at the top.
Values above 99999 m3 cannot be indicated;
“Error” and “–––– ” appear on the display. Divide the volume to be measured into individual
measurements; their values can then be calculated separately and then summarized.
Minimum Measurement (see figure F)
The minimum measurement is used to determine the shortest distance from a fixed reference point. It is used, as an example, for determining plumb lines or horizontal partitions.
For minimum measurements, press button 4
until “MIN” appears in the display.
To start the measurement, briefly press the
measuring button 10.
Move the laser back and forth over the requested target (e.g., the room ceiling for determining
the plumb line) in such a manner that the reference point of the measurement (e.g., the tip of
the positioning pin 15) always remains at the
same location.
During the measurement,
the current length measurement value is indicated
at the bottom of the display. The minimum value is
indicated at the top right in
the display. It is always overwritten, when the
current length measurement value is lower than
the present minimal value.
To end the minimum measurement, briefly press
the measuring button 10. Pressing the measuring button again starts a new measurement.
Bosch Power Tools
OBJ_BUCH-703-002.book Page 23 Wednesday, July 23, 2008 3:15 PM
English | 23
Maximum Measurement (see figure G)
The maximum measurement is used to determine the greatest distance from a fixed reference point. It is used, as an example, for determining diagonals.
For maximum measurements, press button 4
until “MAX” appears in the display.
To start the measurement, briefly press the
measuring button 10.
Move the laser back and forth over the requested target (e.g., the room corner for determining
the diagonal) in such a manner that the reference point of the measurement (e.g., the tip of
the positioning pin 15) always remains at the
same location.
During the measurement,
the current length measurement value is indicated
at the bottom of the display. The minimum value is
indicated at the top right in
the display. It is always overwritten, when the
current length measurement value is larger than
the present maximal value.
To end the maximum measurement, briefly press
the measuring button 10. Pressing the measuring
button again starts a new measurement.
Indirect Length Measurement (see figure H)
The indirect length measurement is used to
measure distances that cannot be measured
directly because an obstacle would obstruct the
laser beam or no target surface is available as a
reflector. Correct results are achieved only when
the laser beam and the sought distance form an
exact right angle (Pythagorean Theorem).
In the illustrated example, the length B is to be
determined. For this purpose, A and C must be
measured. A and B must form a right angle.
For indirect length measurements, press button
11 until the indicator for indirect length measurement
appears in the display.
Measure the distance A as for a length measurement. Pay attention that the line segement A
and the sought distance B form a right angle.
Afterwards, measure the distance C. The laser
beam remains switched on between both measurements.
Bosch Power Tools
Pay attention that the reference point of the
measurement (e.g., the rear edge of the measuring tool) is at the exact same location for both
measurements.
After completing the second measurement, the distance B is calculated automatically. The last individual
measured value is indicated
at the bottom in the display,
while the final result B is indicated at the top.
Wall Surface Measurement (see figure I)
The wall surface measurement is used to determine the sum of several individual surfaces with
a common length.
In the example shown, the total surface of several walls that have the same room height A, but
different lengths B, are to be determined.
For wall surface measurements, press button 11
until the indicator for wall surface measurement
appears in the display.
Measure the room height A as for a length measurement. The measured value is indicated both
at the top and bottom in the display. The laser
remains switched on.
Afterwards, measure length
B1 of the first wall. The surface is automatically calculated and indicated. The
last length measurement
value is indicated at the
bottom in the display, while the surface is indicated at the top. The laser remains switched on.
Now, measure length B2 of
the second wall. The individual measuring value indicated at the bottom of
the display is added to
length B1 and the sum of
both lengths is multiplied with the stored length
A. The total surface value is indicated at the top
in the display.
In this manner, you can measure any number of
further lengths BX, which are added and multiplied with length A.
1 609 929 R53 | (23.7.08)
OBJ_BUCH-703-002.book Page 24 Wednesday, July 23, 2008 3:15 PM
24 | English
The condition for a correct area/surface calculation is that the first measured length (in the
example the room height A) is identical for all
partial surfaces.
To restart the wall surface measurement, press
button 11 twice.
Continuous Measurement (Tracking)
(see figure J)
The continuous measurement function (tracking) is used for the transferring of measurements, e.g., from construction plans. In continuous measurement mode, the measuring tool
can be moved relative to the target, whereby the
measured value is updated approx. every
0.5 seconds. As an example, the user can move
from a wall to the required distance, while the
actual distance can be read continuously.
For continuous measurements, first select the
length measuring function and then press button
10 until the indicator for continuous measurement
appears on the display. The laser is
switched on and the measurement starts immediately.
Move the measuring tool
until the required distance
value is indicated in the
bottom of the display.
Briefly pressing button 10
ends the continuous measurement. The last measured value is indicated at the bottom in the display. Pressing button 10 for several seconds
restarts a continuous measuring run.
The continuous measuring automatically switches off after 5 min. The last measured value remains indicated in the display.
Deleting Measured Values
Briefly pressing button 14 deletes the last individual measuring value determined in all measuring functions. Briefly pressing the button repeatedly deletes the individual measured values
in reverse order.
In the wall surface measurement mode, briefly
pressing button 14 the first time deletes the last
individually measured value; pressing the button
a second time deletes all lengths BX.
1 609 929 R53 | (23.7.08)
Memory Functions
When switching off the measuring tool, the value
in the memory is retained.
In the wall surface measurement mode, the total
surface value can be stored; in the minimum and
maximum measuring mode, the minimum and
maximum value can be stored correspondingly.
Storing individual measuring values within these
functions is not possible.
Storing/Adding Measured Values
Push the memory add button 3 in order to store the
current measured value –
a length, area or volume
value, depending on the
current measuring function.
As soon as a value has been stored, “M” is indicated in the display and the “+” behind it briefly
flashes.
If a value is already stored in the memory, the new
value is added to the memory contents, however,
only when the measures of unit correspond.
As an example, when an area value is in the
memory and the current measured value is a
volume value, the addition cannot take place.
“Error” briefly flashes in the display.
Subtracting Measured Values
Push the memory subtraction button 12 in order
to subtract the current measured value from the
memory value. As soon as a value has been subtracted, “M” is indicated in the display and the
“– ” behind it briefly flashes.
If a value is already stored in the memory, the
new measured value can be subtracted only
when the measures of unit correspond (see
“Storing/Adding Measured Values”).
Displaying the Stored Value
Push the memory retrieve
button 2 in order to display
the value stored in the
memory. “M=” is indicated
in the display. When the
memory contents “M=” is
indicated in the display, it can be doubled by
pushing the memory add button 3 or set to zero
by pushing the memory subtract button 12.
Bosch Power Tools
OBJ_BUCH-703-002.book Page 25 Wednesday, July 23, 2008 3:15 PM
English | 25
Deleting the Memory
To delete the memory contents, first push the
memory retrieve button 2, so that “M=” is indicated in the display. Then briefly press button
14; “M” is no longer indicated in the display.
Measuring with the Positioning Pin
(see figures C, F and G)
Working Advice
Slide the latch 16 of the positioning pin sideward in order to swivel out the pin.
General Information
The reception lens 22 and the laser beam outlet
21 must not be covered when taking a measurement.
The measuring tool must not be moved while
taking a measurement (with the exception of
the continuous measurement function and the
minimum/maximum measurement). Therefore,
place the measuring tool, as far as this is possible, against or on the measuring points.
Measurement takes place at the centre of the laser beam, even when target surfaces are sighted
at an incline.
Influence Effects on the Measuring Range
The measuring range depends upon the light
conditions and the reflection properties of the
target surface. For improved visibility of the
laser beam when working outdoors and when
the sunlight is intense, use the laser viewing
glasses 24 (accessory) and the laser target plate
25 (accessory), or shade off the target surface.
Influence Effects on the Measuring Result
Due to physical effects, faulty measurements
cannot be excluded when measuring on different surfaces. Included here are:
– Transparent surfaces (e.g., glass, water),
– Reflecting surfaces (e.g., polished metal,
glass),
– Porous surfaces (e.g. insulation materials),
– Structured surfaces (e.g., roughcast, natural
stone).
The positioning pin 15 is suitable for measuring
out of corners (diagonal within a space) or from
hard to reach areas, such as from roller-shutter
rails.
Set the corresponding reference level for measurements with the positioning pin by pushing
button 1.
The positioning pin 15 swivels back in again by
pushing it toward the housing to the stop. The
pin automatically locks in place.
Aligning with the Spirit Level
The spirit level 6 allows for simple levelling of the
measuring tool. This allows for easier sighting of
target surfaces, especially over longer distances.
In combination with the laser beam, the spirit
level 6 is not suitable for levelling.
Sighting with the Alingment Aid (see figure K)
With the alignment aid 8, sighting over larger distances is a lot easier. For this, look alongside the
aligning aid on the top side of the measuring tool.
The laser beam runs parallel to this line of sight.
Working with the Tripod (Accessory)
The use of a tripod is particularly necessary for
larger distances. Position the measuring tool
with the 1/4" thread 17 onto the quick-change
plate of the tripod 23 or a commercially available
camera tripod. Tighten the measuring tool with
the locking screw of the quick-change plate.
Set the corresponding reference level for measurement with a tripod by pushing button 1 (the
reference level is the thread).
If required, use the laser target plate 25 (accessory) on these surfaces.
Also, air layers with varying temperatures or
indirectly received reflections can affect the
measured value.
Bosch Power Tools
1 609 929 R53 | (23.7.08)
OBJ_BUCH-703-002.book Page 26 Wednesday, July 23, 2008 3:15 PM
26 | English
Troubleshooting – Causes and
Corrective Measures
Cause
Corrective
Measure
Temperature indicator (c) flashes; measurement not possible
The measuring tool is outside the operating temperature range from
– 10 °C to + 50 °C (in the
function continuous
measurement up to
+40 °C).
Wait until the
measuring tool
has reached the
operating temperature
Cause
Unreliable measuring result
The target surface does
not reflect correctly
(e.g. water, glass).
Cover off the
target surface
The laser beam outlet 21
or the reception lens 22
are covered.
Make sure that the
laser beam outlet
21 or the reception lens 22 are
unobstructed
Measuring result not plausible
Wrong reference level set
Select reference
level that corresponds to measurement
Obstruction in path of
laser beam
Laser point must
be completely on
target surface.
Battery indication (b) is indicated
Battery voltage decreasing (measurement still
possible)
Replace batteries
Battery indication (b) flashes, measurement
not possible
Battery voltage too low
Replace batteries
“Error” and “–––– ” indication in display
The angle between the
laser beam and the target
is too acute.
Enlargen the angle
between the laser
beam and the
target
The target surface reflects Work with the
too intensely (e.g. a mirlaser target plate
ror) or insufficiently (e.g. 25 (accessory)
black fabric), or the ambient light is too bright.
The laser beam outlet 21
or the reception lens 22
are misted up (e.g. due to
a rapid temperature
change).
Wipe the laser
beam outlet 21
and/or the reception lens 22 dry
using a soft cloth
Calculated value is greater than 99999 m/m2/m3.
Divide calculation
into intermediate
steps
“Error” indication flashes at in display (top)
Addition/Subtraction of
Only add/subtract
measured values with dif- measured values
ferent units of measure
with the same
units of measure
1 609 929 R53 | (23.7.08)
Corrective
Measure
The measuring tool monitors the
correct function for each measurement. When a defect is determined, only the symbol shown
aside flashes in the display. In this
case, or when the above mentioned corrective measures cannot correct an
error, have the measuring tool checked by an
after-sales service agent for Bosch power tools.
Accuracy Check of the Measuring Tool
The accuracy of the measuring tool can be
checked as follows:
– Select a permanently unchangeable measuring section with a length of approx. 3 to
10 metres; its length must be precisely
known (e.g. the width of a room or a door
opening). The measuring distance must be
indoors; the target surface for the measurement must be smooth and reflect well.
– Measure the distance 10 times after another.
The measuring error must not amount to more
than a maximum of ± 2.0 mm. Keep a record of
the measurements in order to compare the accuracy at a later time.
Bosch Power Tools
OBJ_BUCH-703-002.book Page 27 Wednesday, July 23, 2008 3:15 PM
English | 27
Maintenance and Service
Maintenance and Cleaning
Store and transport the measuring tool only in
the supplied protective case.
Keep the measuring tool clean at all times.
Do not immerse the measuring tool into water
or other fluids.
Wipe off debris using a moist and soft cloth.
Do not use any cleaning agents or solvents.
Maintain the reception lens 22 in particular,
with the same care as required for eye glasses
or the lens of a camera.
If the measuring tool should fail despite the care
taken in manufacturing and testing procedures,
repair should be carried out by an authorized
after-sales service centre for Bosch power tools.
In all correspondence and spare parts orders,
please always include the 10-digit article
number given on the type plate of the measuring
tool.
In case of repairs, send in the measuring tool
packed in its protective case 27.
Accessories/Spare Parts
Accessories
Construction tripod
BS 150 23 . . . . . . . . . . . . . . . . . 0 601 096 974
Laser viewing glasses 24 . . . . . . 2 607 990 031
Laser target plate 25 . . . . . . . . . 2 607 001 391
Spare Parts
Carrying strap 26 . . . . . . . . . . . . 1 609 203 R97
Protective case 27 . . . . . . . . . . . 1 609 203 X26
Battery lid 19 . . . . . . . . . . . . . . . 1 609 203 X36
Positioning pin 15 . . . . . . . . . . . 1 609 203 X48
Bosch Power Tools
After-sales Service and Customer
Assistance
Our after-sales service responds to your questions concerning maintenance and repair of your
product as well as spare parts. Exploded views
and information on spare parts can also be
found under:
www.bosch-pt.com
Our customer consultants answer your questions concerning best buy, application and adjustment of products and accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: SPT-Technical.de@de.bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: +353 (01) 4 66 67 00
Fax: +353 (01) 4 66 68 88
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: +61 (01300) 307 044
Fax: +61 (01300) 307 045
Inside New Zealand:
Phone: +64 (0800) 543 353
Fax: +64 (0800) 428 570
Outside AU and NZ:
Phone: +61 (03) 9541 5555
www.bosch.com.au
1 609 929 R53 | (23.7.08)
OBJ_BUCH-703-002.book Page 28 Wednesday, July 23, 2008 3:15 PM
28 | English
People’s Republic of China
Malaysia
Website: www.bosch-pt.com.cn
Robert Bosch (SEA.) Pte. Ltd.
No. 8a, Jalan 13/6
46200 Petaling Jaya,
Selangor,
Malaysia
Tel.: +6 (03) 7966 3000
Fax: +6 (03) 7958 3838
E-Mail: hengsiang.yu@my.bosch.com
Toll Free Tel.: 1 800 880 188
Fax: +6 (03) 7958 3838
www.bosch.com.sg
China Mainland
Bosch Power Tools (China) Co., Ltd.
567, Bin Kang Road
Bin Jiang District 310052
Hangzhou, P.R.China
Service Hotline: 800 8 20 84 84
Tel.: +86 (571) 87 77 43 38
Fax: +86 (571) 87 77 45 02
HK and Macau Special Administrative Regions
Robert Bosch Hong Kong Co. Ltd.
21st Floor, 625 King’s Road
North Point, Hong Kong
Customer Service Hotline: +852 (21) 02 02 35
Fax: +852 (25) 90 97 62
E-Mail: info@hk.bosch.com
www.bosch-pt.com.cn
Indonesia
PT. Multi Tehaka
Kawasan Industri Pulogadung
Jalan Rawa Gelam III No. 2
Jakarta 13930
Indonesia
Tel.: +62 (21) 4 60 12 28
Fax: +62 (21) 46 82 68 23
E-Mail: sales@multitehaka.co.id
www.multitehaka.co.id
Phillippines
Robert Bosch, Inc.
Zuellig Building
Sen. Gil Puyat Avenue
Makati City 1200, Metro Manila
Philippines
Tel.: +63 (2) 8 17 32 31
www.bosch.com.ph
1 609 929 R53 | (23.7.08)
Thailand
Robert Bosch Ltd.
Liberty Square Building
No. 287, 11 Floor
Silom Road, Bangrak
Bangkok 10500
Tel.: +66 (2) 6 31 18 79 – 18 88 (10 lines)
Fax: +66 (2) 2 38 47 83
Robert Bosch Ltd., P. O. Box 2054
Bangkok 10501, Thailand
Bosch Service – Training Centre
2869-2869/1 Soi Ban Kluay
Rama IV Road (near old Paknam Railway)
Prakanong District
10110 Bangkok
Thailand
Tel.: +66 (2) 6 71 78 00 – 4
Fax: +66 (2) 2 49 42 96
Fax: +66 (2) 2 49 52 99
Singapore
Robert Bosch (SEA.) Pte. Ltd.
38 C Jalan Pemimpin
Singapore 915701
Republic of Singapore
Tel.: +65 (3) 50 54 94
Fax: +65 (3) 50 53 27
www.bosch.com.sg
Bosch Power Tools
OBJ_BUCH-703-002.book Page 29 Wednesday, July 23, 2008 3:15 PM
English | 29
Vietnam
Battery packs/batteries:
Robert Bosch (SEA) Pte. Ltd – Vietnam
Representative Office
Saigon Trade Center, Suite 1206
37 Ton Duc Thang Street,
Ben Nghe Ward, District 1
HCMC
Vietnam
Tel.: +84 (8) 9111 374 – 9111 375
Fax: +84 (8) 9111376
Do not dispose of battery packs/batteries into
household waste, fire or water. Battery packs/
batteries should be collected, recycled or disposed of in an environmental-friendly manner.
Disposal
Measuring tools, accessories and packaging
should be sorted for environmental-friendly
recycling.
Only for EC countries:
Do not dispose of measuring tools
into household waste!
According the European Guideline
2002/96/EC for Waste Electrical
and Electronic Equipment and its
implementation into national
right, measuring tools that are no longer usable
must be collected separately and disposed of in
an environmentally correct manner.
Bosch Power Tools
Only for EC countries:
Defective or dead out battery packs/batteries
must be recycled according the guideline
91/157/EEC.
Batteries no longer suitable for use can be
directly returned at:
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: SPT-Technical.de@de.bosch.com
Subject to change without notice.
1 609 929 R53 | (23.7.08)