Cornelius ED150 Ice Maker User manual
Add to My manualsCornelius 322 is a versatile ice maker that can produce up to 22 inches wide ice cubes. It's perfect for a variety of applications, including restaurants, bars, and convenience stores. The 322 is also easy to install and maintain, making it a great choice for busy business owners.
advertisement
ED150 “K” Style Lid Kit Installation Instructions
INSTALLATION INSTRUCTIONS
ED150 “K” S
TYLE
L
ID
K
ITS
(P/N 08008, 02390)
ON
THE
F
OLLWING
I
CE
M
AKER
U
NITS
Table 1. Applicable Ice Maker Models
ICEMAKER MODELS
Cornelius 322/522 (includes AC/WC 322)
Crystal Tips 200/300/400
Ice-O-Matic GC 300/550
Manitowoc 320/420
Scotsman SLC 300/400
Servend S2/4
SIZE (WIDTH)
22”
22”
22”
22”
22”
22”
7
8
5
6
2
3
4
9
10
11
12
Item No.
1
Part No.
52994
52934
15506
29565
70217
50904
90221
92111
620701902
620701901
620042928
620701903
620505804
Table 2. Loose Shipped Parts
Name
Cover, Gray - 08008
Cover, Black - 02390
Lid Assembly
Bracket
#8 Screw
RTV
Label
Installation Instruction
Acorn Nut, 8-32 Nylon
Sealing Washer
Baffle, Ice DF/ED150
#8 Nylon Washer
Insulation Strip
!
WARNING:
Disconnect power to the unit before installing the adaptor following all lockout/tag out procedures established by the user. Verify that all the power is off to the unit before performing any work.
Failure to comply could result in serious injury, death or damage to the equipment.
!
WARNING:
All ice baffle plates and bin stats, if included or recommended in this kit, must be installed as directed in this manual or the equipment manufacturer’s instructions.
Failure to comply could result in serious injury, death or damage to the equipment.
!
WARNING:
All of the attachment screws and plates must be installed as directed in this manual.
Failure to comply could result in serious injury, death or damage to the equipment.
Perform the following procedure to install the lid kit.
Qty.
2
1
1
2
2
1
1
1
2
6
1
1
1
Release Date: October 22, 2010
© 1996-2010, IMI Cornelius Inc.
www.cornelius.com
- 1 -
Revision: B
Publication Number: 92111INS
ED150 “K” Style Lid Kit Installation Instructions
1.
Unpack kit.
2.
Place insulation strip (item 12) over studs on the ice baffle (item 10) and insert ice baffle into the lid assembly
(item 2).
3.
Place (2) sealing washers (item 9) over studs and (2) flat washers (item 11), then fasten in place with (2) plastic acorn nuts (item 8).
4.
Set ice maker lid assembly on the top of the dispenser.
5.
Using the slotted holes in the lid as a template, drill four (4) 0.140" diameter (9/64") holes at the bottom of the slots
(see detail A). Use extreme care not to drill into the hopper. Fasten the lid assembly to the dispenser with two (2)
#8 sheet metal screws (item 4), one on each side.
6.
Seal the ice maker to the top of the dispenser as follows:
7.
Run beads of RTV (item 5) around the opening in the lid assembly and inside of the perimeter of the ice maker outline so that the ice maker will set on the RTV.
A. Set the ice maker onto the lid assembly and position it as required.
B. Wipe away the excess RTV.
8.
Drill 9/64
diameter holes into the ice maker cabinet using the bracket (item 3) as a template. Use extreme care not to drill into any ice maker components (condenser, tubing, etc.). Secure the brackets using four (4) #8 sheet metal screws (item 4).
9.
Follow the ice maker manufacturers instruction to complete the installation of the ice maker including the bin thermostat if so equipped or required.
10. If the plastic ac or rn nuts interfere with the positioning of the plastic manual fill cover, it may be necessary to make small notches in the back flange of the cover to clear the acorn nuts.
!
CAUTION:
Bin Thermostat must not interfere with the agitator rotation.
Publication Number: 92111INS - 2 © 1996-2010, IMI Cornelius Inc.
ED150 “K” Style Lid Kit Installation Instructions
© 1996-2010, IMI Cornelius Inc.
Figure 1. ED150 Kit
- 3 Publication Number: 92111INS
ED150 “K” Style Lid Kit Installation Instructions
Figure 2. Dispenser Assembly
Publication Number: 92111INS - 4 © 1996-2010, IMI Cornelius Inc.
advertisement
Related manuals
advertisement