ENGLISH
MODEL
HT-SB250(BK)
SOUND BAR SYSTEM
OPERATION MANUAL
SOUND BAR
SYSTEM
HT-SB250
is a trademark of SRS Labs, Inc.
WOW HD technology is incorporated under license from SRS Labs, Inc.
Note: This product is recommended for flat panel TV (LCD and plasma).
10 :
SHARP ELECTRONICS OF CANADA LTD
335 Britannia Road East
Mississauga, Ontario
L4Z 1W9
*TINSKA049AWZZ4Q*|
TINSKA049AWZZ
SHARP CORPORATION
Printed in Malaysia
11A R AS 1
Canada limited warranty
VALID IN CANADA ONLY
LIMITED WARRANTY
Consumer Electronics Products
Congratulations on your purchase!
Sharp Electronics of Canada Ltd. (“Sharp”) warrants to the first purchaser for this Sharp brand product (“Product”), when shipped in
its original container and sold or distributed in Canada by Sharp or by an authorized Sharp dealer, that the Product will during the
applicable warranty period, be free from defects in material and workmanship, and will within the applicable warranty period, either
repair the defective Product or provide the first purchaser a replacement of the defective Product.
Conditions: This limited warranty shall not apply to:
(a) Any defects caused or repairs required as a result of abusive operation, negligence, accident, improper installation or
inappropriate use as outlined in the owner’s manual or other applicable Product documentation.
(b) Any defects caused or repairs required as a result of any Product that has been tampered with, modified, adjusted or repaired
by any person other than Sharp, a Sharp authorized service centre or a Sharp authorized servicing dealer.
(c) Any defects caused or repairs required as a result of the use of the Product with items not specified or approved by Sharp,
including but not limited to, head cleaning tapes and chemical cleaning agents.
(d) Any replacement of accessories, glassware, consumable or peripheral items required through normal use of the Product,
including but not limited to, earphones, remote controls, AC adapters, batteries, temperature probe, trays, filters, belts, ribbons,
cables and paper.
(e) Any cosmetic damage to the Product surface or exterior that has been defaced or caused by normal wear and tear.
(f) Any defects caused or repairs required as a result of damage caused by any external or environmental conditions, including but
not limited to, transmission line/power line voltage or liquid spillage or acts of god.
(g) Warranty claims for Products returned with illegible or without appropriate model, serial number and CSA/cUL markings.
(h) Any Products used for rental or commercial purposes.
(i) Any installation, setup and/or programming charges.
How to get service: Warranty service may be obtained upon delivery of the Product, together with proof of purchase (including
date of purchase) and a copy of this limited warranty statement, to an authorized Sharp service centre or an authorized Sharp
servicing dealer. In home warranty service may be provided, at Sharp’s discretion, on any Sharp Television with the screen size of
40” or larger and on any Sharp Over-The-Range Microwave Oven or Home Use Microwave Drawer . No other person (including
any Sharp dealer or service centre) is authorized to extend, enlarge or transfer this warranty on behalf of Sharp. The purchaser will
be responsible for any and all removal, reinstallation, transportation and insurance costs incurred.
The express warranties in this limited warranty are, except for consumer purchasers domiciled in Quebec, in lieu of and, except to
the extent prohibited by applicable law, Sharp disclaims all other warranties and conditions, express or implied, whether arising by
law, statute, by course of dealing or usage of trade, including, without limitation, implied warranties or conditions of merchantability
and/or quality, fitness for a particular use or purpose, and/or non-infringement. Limitations (not applicable to consumer purchasers
domiciled in Quebec to the extent prohibited under Quebec law): (a) Sharp shall not be liable for any incidental, special,
consequential, economic, exemplary or indirect damages of any kind or nature (including lost profits or damages for loss of time or
loss of use or loss of data) arising from or in any connection with the use or performance of a Product or a failure of a Product, even
if Sharp is aware of or has been advised of the possibility of such damages; (b) the remedies described in this limited warranty
constitute complete fulfillment of all obligations and responsibilities of Sharp to the purchaser with respect to the Product and shall
constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. Some provinces may not
allow the exclusion or limitation of certain damages, or limits on the duration or voiding of implied warranties or conditions; in such
provinces, the exclusions and limits herein may not apply. This limited warranty is, except for consumer purchasers domiciled in
Quebec, governed by the laws of the Province in Canada in which the purchaser has purchased the Product. For consumer
purchasers domiciled in Quebec this limited warranty is governed by the laws of Quebec.
WARRANTY PERIODS :
Parts & Labour (exceptions noted)
(calculated from the date of original purchase)
Audio Product
1 year
Blu-Ray Product
1 year
Projector
1 year
(lamp 90 days)
LCD TV
1 year
Microwave Oven
1 year
(magnetron component-4 additional years)
Air Purifier
1 year
Portable Air Conditioner
1 year
Plasmacluster Ion generator 1 year
3D glasses
1 year
Wireless LAN Adapter
1 year
To obtain the name and address of the nearest Authorized Sharp Service Centre or Dealer, or for more information on this Limited
Warranty, Sharp Extended Warranty Offers, Sharp Canada Products or Accessory Sales, please contact Sharp:
ƒ
ƒ
ƒ
By writing to Sharp Electronics Of Canada Ltd. at 335 Britannia Road East Mississauga, Ontario L4Z 1W9
Calling: at 905-568-7140
Visiting our Web site: www.sharp.ca
THIS LIMITED WARRANTY IS VALID ONLY IN CANADA
Revision 12/17/10
Special notes
Features
SRS WOW HD™ significantly improves the playback quality of audio, delivering a dynamic 3D
entertainment experience with deep, rich bass and high frequency clarity for crisp detail.
Accessories
Please confirm that only the following accessories are included.
Remote control x 1
RCA cable
(2 pins - 2 pins) x 1
AC/DC adaptor x 1
(RADPAA075AWZZ)
AC power lead x 1
Nut
Wall mount angle x 2
Foot cushion x 4
Pattern paper x 1
( Spike + Nut ) x 4
Length: 25 mm)
Note: The AC/DC adaptor may be different from the one in the drawing.
E-
Precautions
Warning:
● The voltage used must be the same as that
● Please ensure that the equipment is
specified on this unit. Using this product
positioned in a well-ventilated area and
with a higher voltage other than that which
ensure that there is at least 10 cm (4”) of
is specified is dangerous and may result
free space along the sides and top of the
in a fire or other type of accident causing
equipment.
damage. SHARP will not be held responsible
for any damage resulting from use of this
10 cm (4”)
10 cm (4”)
10 cm (4”)
unit with a voltage other than that which is
specified.
● The supplied AC/DC adaptor contains
no user serviceable parts. Never remove
● Use the unit on a firm, level surface free from
covers unless qualified to do so. It contains
vibration.
dangerous voltages, always remove mains
● Keep the unit away from direct sunlight,
plug from the wall socket before any service
strong magnetic fields, excessive dust,
operation or when not in use for a long
humidity and electronic/electrical equipment
period.
(home computers, facsimiles, etc.) which
● The AC/DC adaptor supplied with the
generate electrical noise.
HT-SB250(BK) must not be used with other
● Do not place anything on top of the unit.
equipment.
● Do not expose the unit to moisture, to
● Never use an AC/DC adaptor other than the
temperatures higher than 60°C (140°F) or
one specified. Otherwise, problem or serious
to extremely low temperatures.
hazards may be created.
● If your system does not work properly,
● To prevent fire or shock hazard, do not
disconnect the AC power lead from the wall
expose this appliance to dripping or
socket. Plug the AC power lead back in, and
splashing. No objects filled with liquids, such
then turn on your system.
as vases, shall be placed on the apparatus.
● In case of an electrical storm, unplug the unit
for safety.
● Hold the AC power plug by the head when
■ Volume control
removing it from the wall socket, as pulling
The
sound level at a given volume setting depends
the lead can damage internal wires.
on unit efficiency, location, and various other
● The AC power plug is used as a disconnect
factors. It is advisable to avoid exposure to high
device and shall always remain readily
volume levels. Do not turn the volume on to full at
operable.
switch on. Listen to music at moderate levels.
● Do not remove the outer cover, as this
may result in electric shock. Refer
internal service to your local SHARP
service facility.
● This unit should only be used within the
range of 5°C - 35°C (41°F - 95°F).
■ General
E-
Controls and indicators
■ Front Panel
1 2
3
4 5
6 7 8 9 10
12 13
.
2.
.
.
5.
.
7.
8.
9.
14
11
14
Reference page
Standard Indicator...................................10
Cinema/Game Indicator..........................10
Information Display.................................10
Sport Indicator.........................................10
News Indicator.........................................10
On/Stand-by Button..................................9
Volume Down Button................................9
Volume Up Button.....................................9
Surround Button......................................10
Reference page
0. Function Button.......................................10
. Remote Sensor
2. Left Front Speaker
. Bass Reflex Duct
. Subwoofers
5. Right Front Speaker
■ Rear Panel
1
LINE IN 2
2
13 15
3
RIGHT
LEFT
LINE IN 1
Reference page
. Audio Line In 2 Socket..............................7
2. Line In 1 Sockets ......................................7
. DC Input Socket .......................................8
E-
Controls and indicators (continued)
■ Remote Control
1
2
3
9
10
11
4
5
6
7
12
13
14
15
8
Remote control
Plastic shield
Reference page
. Remote Control Transmitter
2. Cinema/Game Button..............................10
. Standard Button......................................10
. Volume Up Button.....................................9
5. Subwoofer Level Down Button..............10
. Volume Down Button................................9
7. Bass/Treble Button..................................10
8. TV Operation Buttons...............................4
9. On/Stand-by Button..................................9
0. Sport Button............................................10
. News Button............................................10
2. Subwoofer Level Up Button...................10
. Dimmer Button..........................................9
. Mute Button.............................................10
5. Line Button..............................................10
Battery holder
Note:
Before using remote control, please remove plastic shield at battery holder.
TV Operation Buttons (Only SHARP TV):
On/Stand-by
Button
Sets the TV power to
“ON” or “STAND-BY”.
Input Select Button
(TV)
Press the button
to switch the input
source.
Volume Up and
Down Buttons
Turn up/down the TV
volume.
Channel Up and Down
Buttons
Switch up/down the
TV channels.
Note: ● Some models of SHARP TV may not be operable.
● SHARP TV remote control will not work with HT-SB250(BK) system.
E-
System preparation
Note:
Option 1 or option 2 foot cushion positions based
on LCD TV stand.
Make sure to unplug the AC power lead
before installing the unit or changing the
position.
Select from three installation methods according
to the preferred position.
Using spikes
Nuts (secured on spikes) must be used when
installing spikes.
The unit can be levelled by adjusting the spikes
and nuts.
Option 2
Option 1
Tighten all spikes as shown
Notes:
● Option 1 or option 2 indicates spike positions
based on LCD TV stand.
● When attaching the spikes, place the unit on
a cushion or soft cloth to avoid damage.
Caution:
When using these spikes on glossy or slippery
table such as on glass top, stick foot cushions at
the bottom of the spikes to avoid slippage.
To mount the unit on the wall
Caution:
● Be very careful to prevent the unit [1.90 kg
(4.19 lbs.)] from falling when mounting on the
wall.
● Before mounting, check the wall strength. (Do
not put on the veneer plaster or whitewashed
wall. The unit may fall.) If unsure, consult a
qualified service technician.
● Mounting screws are not supplied. Use
appropriate ones.
● Check all wall mount angle screws for
looseness.
● Select a good location. If not, accidents may
occur or the unit may get damaged.
● SHARP is not responsible for accidents
resulting from improper installation.
■ Driving screws
SHARP designed the units so you may hang them
on the wall. Use proper screws (not supplied). See
below for size and type.
3.2 mm (1/8”)
5 mm
(3/16”)
9 mm (3/8”)
Min. 22 mm (7/8”)
■ Wall mount angle fixed
to the wall (Horizontal
position)
Using foot cushions
Fix the pattern paper to the wall in horizontal
position as below.
Option 2
Attach foot cushions as shown
Option 1
44 mm
509 mm
Wall surface 44 mm
29 mm
E-
29 mm
Pattern paper
System preparation (continued)
■ Installing the sound bar
2 Make a hole on the wall following the screw
point marks on the pattern paper by using
a drill.
32 mm (1-1/4”)
Align the wall mount slot at the unit to the
wall mount angle.
2 Slot the unit into the wall mount angle.
Fix them securely.
8-9 mm (3/8”)
Wall surface
Wall surface
Fix a wall mount plug into the hole using
a hammer, until it is flush with the wall
surface.
1-1/4” (32 mm)
8-9 mm (3/8”)
Wall surface
Screw the wall mount angle to the wall as
shown in the illustration. (Total screw is 8
pieces)
Placing the sound bar
Installation image:
TV
Wall mount angle
Wall surface
Wall mount angle
HT-SB250
(screws x 4)
(screws x 4)
VCR
DVD player
Place the unit as shown.
Wall surface
Wall mount angle
Wall surface
Note:
Make sure all screws are fully tightened.
(screws are not supplied)
Notes:
● As the sound from the unit is omnidirectional, you can place the unit
anywhere you like. However, it is
recommended to place it as close to
the TV as possible.
● The front panel of the unit is not
removable.
Caution:
● Do not change the installation direction
when the unit is turned on.
● Do not stand or sit on the unit as you
may be injured.
E-
Falling prevention
Safety wires (not supplied) are useful to prevent
the unit from falling off the table.
Loop the safety wires (not supplied) into each
hole as shown and tie the safety wires to the
LCD TV stand.
Sound bar connections to TVs
Caution:
Turn off all other equipment before making any
connections.
Tuner receiving for other audio system
● Placing the aerial near the unit AC power
lead may cause noise pick up. Place
the aerial away from the unit for better
reception.
Notes:
● To connect to TV, use either LINE IN 1
sockets or AUDIO LINE IN 2 socket only.
● Refer the operation manual of the
equipment to be connected.
● Fully insert the plugs to avoid fuzzy
pictures or noises.
■ Connecting to a TV (with
Headphone socket)
■ Connecting to a TV
If the TV/monitor has an audio output, connect
it to the LINE IN 1 sockets on the rear of the
unit.
If the TV/monitor has headphone socket, connect it
to the LINE IN 2 socket on the rear of the unit.
HEADPHONE
TV
RCA cable (supplied)
To HEADPHONE
socket
TV
To audio output
sockets
Audio cable
(not supplied)
To LINE IN
1 sockets
Sound bar
To AUDIO
LINE IN 2
socket
Sound bar
To select LINE IN 1 function:
● On the unit: Press FUNCTION button repeatedly
until “L1” is displayed.
● On remote control: Press LINE button repeatedly
until “L1” is displayed.
To select LINE IN 2 function:
● On the unit: Press FUNCTION button repeatedly until
“L2” is displayed.
● On remote control: Press LINE button repeatedly until
“L2” is displayed.
Notes:
● If the TV volume is continuously in low level, the unit
will automatically power off. Increase the TV output
volume to enjoy the sound from the unit.
● If the unit volume is continuously in very high level, the
unit will mute and recover after 3 seconds.
E-
AC power connection
Remote control
After checking all the connections have been made
correctly, connect the AC power lead to the AC
power input socket, then to the wall socket.
■ Battery installation
Insert pin into the hole as shown and pull to
open the battery holder.
■ Using with the AC/DC
adaptor
Pin
1 Plug the AC power lead into the AC/DC
adaptor.
2 Plug the AC/DC adaptor cable into the DC
INPUT socket on the unit.
3 Plug the AC power lead into a wall socket.
AC/DC Adaptor
Cable
Back of
remote control
2 Remove the old battery from the battery
holder, insert the new battery and then
slide the battery holder back into the remote
control.
2
DC INPUT socket
(DC 12V)
LINE IN 2
Battery holder
RIGHT
LEFT
LINE IN 1
Polarity (+) symbol
AC power lead
Positive (+) side up
1
Wall socket
Battery type
Locking tab
AC/DC Adaptor
(AC 100 - 240 V
~ 50/60 Hz)
Caution:
If this product is to be used in other than 120 V region, please
change the AC power lead to suit the region.
The AC power lead part codes for 220 - 240 V region are
as follow :
1) QACCEA002AW00 (For Europe and Latin America
region)
2) QACCBA005AW00 (For United Kingdom region)
3) QACCLA002AW00 (For Australia region)
Notes:
● There will be no indication during power stand-by mode
unless the ON/STAND-BY button is pressed.
● Unplug the AC/DC adaptor from the wall socket if the
unit will not be used for a prolonged period of time.
● Use only the supplied AC/DC adaptor. Using other AC/
DC adaptor may cause an electric shock or fire.
Caution:
To prevent electric shock, match
wide blade of plug to wide slot, fully
insert.
Precautions for battery use:
Remove the battery if the unit will not be used for
a long period of time. This will prevent potential
damage due to battery leakage.
Caution:
● Do not use rechargeable battery (nickelcadmium battery, etc.).
● Danger of explosion if battery is incorrectly
replaced.
● Replace only with the same or equivalent
type.
● Batteries (battery pack or batteries installed)
shall not be exposed to excessive heat such
as sunshine, fire or the like.
● Installing the battery incorrectly may cause
the unit to malfunction.
E-
General control
Remote control
(continued)
Notes concerning use:
● Replace the battery if the operating distance
is reduced or if the operation becomes
erratic. Purchase “CR 2025”, coin lithium
battery.
● Periodically clean the transmitter on the
remote control and the sensor on the unit
with a soft cloth.
● Exposing the sensor on the unit to strong
light may interfere with operation. Change
the lighting or the direction of the unit if this
occurs.
● Keep the remote control away from moisture,
heat, shock, and vibrations.
SPORT
CINEMA/GAME
■ To turn the power on
Press the ON/STAND-BY button.
● The sound mode indicator and display light up.
Note:
If the power does not turn on, check whether the
power lead is plugged in properly.
To set the unit to stand-by mode:
● Press the ON/STAND-BY button again.
■ Display brightness control
Press the Dimmer button to adjust the brightness
of the display and sound mode indicator.
Sound mode indicator and display bright
Sound mode indicator and display dim
Sound mode indicator and display off. Pressing
any button will light up the display for 3
seconds only.
■ Volume auto fade-in
If you turn off and on the unit with the volume set
to 40 or higher, the volume starts at 20 and fades
in to the last set level.
■ Volume control
Unit operation:
Press volume up (VOL. + ) to increase the volume
and press volume down (VOL. – ) to decrease the
volume.
E-
00
01
02 .....
59
60
General control (continued)
Remote control operation:
Press the VOLUME + button to increase the volume
and the VOLUME – button to decrease the volume.
■ Bass control
Press the
BASS/TREBLE
button to select
“BASS”.
■ Muting
The volume is muted temporarily
when pressing the MUTE button
on the remote control. Press again
to restore the volume.
(+ or –) button to adjust the bass.
Main unit operation:
To change to a different mode, press the
SURROUND button repeatedly until the desired
sound mode lights up.
Remote control operation:
Press a desired sound mode on the remote
control.
WOW
is on for
nominal
WOW HD
is on HD
for nominal
effect.
STANDARD
STANDARD
effect
WOW HD on for cinema/game sound effect
WOW
onbroadcasting
for cinema/
WOW HD
on forHD
sport
SPORT
CINEMA/GAME
NEWS
game sound effect
WOW HD on for news
SPORT
WOW HD on for sport
broadcasting
NEWS
WOW HD on for news
■ Treble control
Press the
BASS/TREBLE
button to select
“TREBLE”.
-5
+5
2 Within 5 seconds, press the VOLUME
(+ or –) button to adjust the treble.
■ Function
When the FUNCTION
LINE 1
button on unit or LINE
button on the remote
control is pressed, the
LINE 2
input source will change.
Press the FUNCTION
button on unit or LINE button on the remote control
repeatedly to select desired input source.
Note:
The backup function will protect the memorised
function mode for a few hours should there be
a power failure or the AC power lead becomes
disconnected.
■ Subwoofer level control
The unit level can be adjusted.
To increase the level, press
the SUBWOOFER LEVEL
-5 -4 ...
button.
To decrease the level, press
the SUBWOOFER LEVEL
button.
+5
2 Within 5 seconds, press the VOLUME
■ Preset sound mode
CINEMA/GAME
-5
Auto power on function:
When you press the LINE button on the remote
control, the unit will turn on at last function.
4
5
Note:
When sound from the unit is distorted, decrease
the subwoofer level.
Auto power off and auto detect signal:
● If no signal is detected for 20 minutes during
power on, the unit will automatically go to
stand-by mode. The STAND-BY indicator
turns red.
● The unit will automatically power ON if
it detects audio signal from connected
equipment, unless it is turned off manually.
E-10
Troubleshooting chart
Many potential problems can be resolved
by the owner without calling a service
technician.
If something is wrong with this product, check
the following before calling your authorised
SHARP dealer or service center.
■ General
Symptom
■ Remote control
Symptom
● Is the battery
polarity correct?
● Is the battery
dead?
● Is the distance or
angle incorrect?
● Are there any
obstructions in
front of the unit?
● Is there a strong
light shining
on the remote
sensor?
● Is the remote
control for
another
equipment used
simultaneously?
The unit cannot
be turned on
with the remote
control.
● Is the AC power
lead of the unit
plugged in?
● Is the battery
inserted?
TV cannot be
operated with
the remote
control.
● Depending on
the model, some
or all functions
may not be
operable using
the remote
control of this
unit. In this case,
use the remote
control supplied
with the TV.
Possible cause
No sound is
heard.
● Is the input signal
(selection) set
properly?
● Is the volume
level set to “0”?
● Is muting
activated?
Noise is
heard during
playback.
● Move the unit
away from any
computers or
mobile phones.
When a button
is pressed, the
unit does not
respond.
● Set this unit to
the stand-by
mode and then
turn it back on.
The power is
not turned on.
● Is the unit
unplugged?
(Refer to page 8.)
● The protection
circuit may be
activated. Unplug
and plug in the
power lead again
after 5 minutes or
more.
The information
is not displayed
even if the unit
is turned on.
● Is the unit set
to “Display off
mode“?
Possible cause
The remote
control does
not operate
properly.
E-11
Troubleshooting chart (continued)
■ Condensation
Sudden temperature changes, storage or
operation in an extremely humid environment
may cause condensation inside the cabinet
or on the transmitter on the remote control.
Condensation can cause the unit to malfunction. If this happens, leave the power on until
normal playback is possible (about 1 hour).
Wipe off any condensation on the transmitter
with a soft cloth before operating the unit.
■ If problem occurs during operation
When this product is subject to strong
external interference (mechanical shock,
excessive static electricity, abnormal supply
voltage due to lightning, etc.) or if it is
operated incorrectly, it may malfunction.
■ Factory reset, clearing all
setting
Make sure to disconnect all audio input
cables attached to the unit before performing
the factory reset.
1. Press the ON/STAND-BY button to enter
the power stand-by mode.
2. Whilst pressing the SURROUND button,
press and hold the ON/STAND-BY button
until “CL” appears.
Caution:
This operation will erase all data stored in
memory.
If such a problem occurs, do the
following:
Set the unit to the stand-by mode and
turn the power on again.
2 If the unit is not restored in the
previous operation, unplug and plug in
the unit, and then turn the power on.
E-12
Maintenance
■ Cleaning the cabinet
Periodically wipe the cabinet with a soft
cloth.
Caution:
● Do not use chemicals for cleaning
(gasoline, paint thinner, etc.). It may
damage the cabinet finish.
● Do not apply oil to the inside of each
component. It may cause malfunctions.
HT-SB250
Error indicators and warnings
When you fail to perform operations properly, the following messages are displayed on
the unit.
Display
or
Meaning
or
Power indicator (blinks red)
● Malfunction of the surround circuit. Place the unit
away from noise source and plug the AC power
lead into another wall socket. (*)
● When the protection circuit of the amplifier is
activated.
(*): Should the same message appear even if the unit is unplugged and plugged in or is
set to the stand-by mode and on again, contact your local dealer where you purchased
the unit.
E-13
Specifications
As part of our policy of continuous improvement,
SHARP reserves the right to make design and
specification changes for product improvement
without prior notice. The performance specification figures indicated are nominal values of
production unit. There may be some deviations
from these values in individual unit.
■ General
Power
source
DC IN 12V 4A: AC/DC
adaptor
(AC 100 - 240 V ~ 50/60
Hz)
Power
consumption
10 W
Output
power
Front speaker:
RMS: 12 W (6 W + 6 W)
(10% T.H.D.)
Subwoofer:
RMS: 20 W (10% T.H.D.)
Speaker
2.1-way Speaker System
Front Speakers: 40 mm
(1-1/2”) Full Range
Impedance: 12 ohms /
Channel
Subwoofer: 57 mm (2-1/4”)
Woofer (x4)
Impedance: 3 ohms
Input
terminals
Analog input (LINE 1):
RCA type x 1pair (L/R)
500 mV / 47 kohms
Analog input (LINE 2):
Stereo mini socket Ø
3.5 mm
100 mV / 47 kohms
Dimensions
Width: 851 mm (33-1/2”)
Height: 96 mm (3-3/4”)
Depth: 70 mm (2-3/4”)
Weight
1.90 kg (4.19 lbs.)
E-14