advertisement
DLP™ PROJECTOR
MODEL
TX20U
TW21U
User Manual
TX20U
TW21U
This User Manual is important to you.
Please read it before using your projector.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE
EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR
THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
WARNING
Use the attached specified power supply cord. If you use another power supply cord, it may cause interference with radio and television reception.
This apparatus must be grounded.
DO NOT LOOK DIRECTLY INTO THE LENS
WHEN THE PROJECTOR IS IN THE POWER
ON MODE.
CAUTION
The attached power cord is to be used exclusively for this product. Never use it for other products.
EN-2
Contents
Trademark, Registered trademark
• DLP™, Digital Micromirror Device, DMD, and BrilliantColor™ are all trademarks of Texas Instruments.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
• Microsoft, Windows, Windows Vista, Windows Server, MultiPoint, Excel, and PowerPoint are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
• Mac, Mac OS, OS X, Finder, and Apple Store are trademarks of Apple Inc.
• Intel and Pentium are trademarks of Intel Corporation in the U.S. and/or other countries.
• PowerPC is a trademark of International Business Machines Corporation, registered in many jurisdictions worldwide.
• IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.
• Android and Google are trademarks of Google Inc.
• MirrorOp, MirrorOp Receiver, and WiFi-Doc are registered trademarks, trademarks, or trade names of AWIND Inc.
• Wi-Fi is a registered trademark of the Wi-Fi Alliance.
• The trademark of PJLink is trademark applied for registration or registered trademark in Japan, the United States, and other countries and areas.
• Crestron RoomView Connected is a trademark of Crestron Electronics, Inc.
• Other brand or product names are trademarks or registered trademarks of their respective holders.
EN-3
Important safeguards
Please read all these instructions regarding your projector and retain them for future reference. Follow all warnings and instructions marked on the projector.
1. Read instructions
All the safety and operating instructions should be read before the appliance is operated.
2. Retain instructions
The safety and operating instructions should be retained for future reference.
3. Warnings
All warnings on the appliance and in the operating instructions should be adhered to.
4. Instructions
All operating instructions must be followed.
5. Cleaning
Unplug this projector from the wall outlet before cleaning it. Do not use liquid aerosol cleaners. Use a damp soft cloth for cleaning.
6. Attachments and equipment
Never add any attachments and/or equipment without the approval of the manufacturer as such additions may result in the risk of fire, electric shock or other personal injury.
7. Water and moisture
Do not use this projector near water or in contact with water.
8. Accessories
Do not place this projector on an unstable cart, stand, tripod, bracket or table. Use only with a cart, stand, tripod bracket, or table recommended by the manufacturer or sold with the projector. Any mounting of the appliance should follow the manufacturer’s instructions and should use a mounting accessory recommended by the manufacturer.
An appliance and cart combination should be moved with care. Quick stops, excessive force and uneven surfaces may cause the appliance and cart combination to overturn.
9. Ventilation
Slots and openings in the cabinet are provided for ventilation, ensuring reliable operation of the projector and to protect it from overheating. Do not block these openings or allow them to be blocked by placing the projector on a bed, sofa, rug, or bookcase. Ensure that there is adequate ventilation and that the manufacturer’s instructions have been adhered to.
10.Power sources
This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power, please consult your appliance dealer or local power company.
11.Power-cord protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords at plugs, convenience receptacles, and points where they exit from the appliance. Do not put the power cord under a carpet.
12.Overloading
Do not overload wall outlets and extension cords as this can result in a fire or electric shock.
13.Objects and liquids
Never push objects of any kind through openings of this projector as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector.
14.Servicing
Do not attempt to service this projector by yourself.
Refer all servicing to qualified service personnel.
15.Damage requiring service
Unplug this projector from the wall outlet and refer servicing to qualified service personnel under the following conditions:
(a) If the power-supply cord or plug is damaged.
(b) If liquid has been spilled, or objects have fallen into the projector.
(c) If the projector does not operate normally after you follow the operating instructions. Adjust only those controls that are covered by the operating instructions. An improper adjustment of other controls may result in damage and may often require extensive work by a qualified technician to restore the projector to its normal operation.
(d) If the projector has been exposed to rain or water.
(e) If the projector has been dropped or the cabinet has been damaged.
(f) If the projector exhibits a distinct change in performance - this indicates a need for service.
16.Replacement parts
When replacement parts are required, be sure that the service technician has used replacement parts specified by the manufacturer or parts having the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
17.Safety check
Upon completion of any service or repair to this projector, ask the service technician to perform safety checks determining that the projector is in a safe operating condition.
EN-4
Important safeguards (continued)
WARNING:
Unplug immediately if there is something wrong with your projector.
Do not operate if smoke, strange noise or odor comes out of your projector. It may cause fire or electric shock.
In this case, unplug immediately and contact your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An inadvertent contact may result in an electric shock.
Except as specifically explained in User Manual, do not attempt to service this product by yourself. Please contact your dealer when you want to fix, adjust, or inspect the projector.
Do not modify this equipment.
It can lead to fire or electric shock.
Do not keep using the damaged projector.
If the projector is dropped and the cabinet is damaged, unplug the projector and contact your dealer for inspection. It may lead to fire if you keep using the damaged projector.
Be sure to unplug the power cord from the wall outlet if the projector is fractured or deformed.
Otherwise, it may result in fire or electric shock. Ask your dealer for repair.
Do not face the projector lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven surface.
Place the projection on a leveled and stable surface only.
Do not look into the lens when it is operating.
It may hurt your eyes. Never let children look into the lens when it is on.
Do not put any objects immediately in front of the lens while the lamp is on.
The lens and the objects get hot and can cause fire or breakdown.
Do not unplug the power cord during operation.
It can lead to lamp breakage, fire, electric shock or other trouble.
EN-5
Do not touch the exhaust vents and bottom plate.
Do not touch them or put other equipment close to the exhaust vents because they become hot during operation. The heated exhaust vents and bottom plate may cause injury or damage to other equipment. Also, do not put the projector on a desk that is easily affected by heat.
Do not look into the exhaust vents when projector is operating.
Heat, dust, etc. may blow out of it and hurt your eyes.
Do not block the intake and exhaust vents.
If they are blocked, heat may be generated inside the projector, causing deterioration in the projector quality and fire.
Do not use flammable solvents (benzene, thinner, etc.) and flammable aerosols near the projector.
Flammable substances may ignite causing fire or breakdown because the temperature inside the projector rises very high while the lamp is illuminating.
Do not use the projector with condensation on it.
It can lead to breakdown or other failure.
Place of installation
For safety’s sake, do not use the projector at any place subjected to high temperature and high humidity.
Please maintain an operating temperature, humidity, and altitude as specified below.
• Operating temperature: between +41°F (+5°C) and
+95°F (+35°C)
• Operating humidity: between 30% and 90%
• Never put any heat-producing device under the projector to prevent the projector from being overheated.
• Do not install the projector at a place that is unstable or subject to vibration.
• Do not install the projector near any equipment that produces a strong magnetic field. Also refrain from installing the projector near any cable carrying a large amount of current.
• Place the projector on a solid, vibration-free surface.
Otherwise it may fall, causing serious injury or damage.
• Do not stand the projector on its end. It may fall, causing serious injury or damage.
• Slanting the projector more than ±10° (right and left) or ±15° (front and rear) may cause trouble or explosion of the lamp.
• Do not place the projector near air-conditioning unit, heater, or humidifier to avoid hot or moist air to the exhaust and ventilation hole of the projector.
Important safeguards (continued)
• Do not place the projector in the following places.
Otherwise, a short circuit, heat generation, or melting of the power cord coating may occur, causing fire, electric shock, product failure, or deformation.
• Outdoors or non air-conditioned place
• Place where a gas such as a hydrogen sulfide is generated (i.e. hot spring)
• Place where there is too much salt such as near the coast
• Be sure to use this projector at an altitude of less than 1500 meters.
Do not place a container containing water or other liquid on the projector.
If water spills on or enters the projector, it may result in fire or electric shock.
Do not put any object that is heavy or larger than the outer frame on the projector.
Otherwise, the object may fall losing its balance and cause injury.
Do not subject the projector to strong shocks or vibrations. Do not handle the projector roughly.
The projector may be damaged, resulting in fire or electric shock.
When removing the lamp from the ceilingmounted projector
Be sure to use the lamp replacement attachment designed specifically for this projector when replacing the lamp with a new one. Lamp fragments may fall from the inside if the lamp were broken.
Do not put the projector in the soft case with the power cord and cables connected.
The projector, power cord, or cables may be damaged.
EN-6
Overview
10
3 1 2
8 4 9 7
5
1 FOCUS ring
2 ZOOM ring
3 Control panel
4 Remote control sensor
5 Exhaust vent
6 Terminal panel
7 Speaker
8 Adjustment feet
9 Lock bar
10 Lamp cover
Caution:
• Do not replace the lamp immediately after using the projector because the lamp would be extremely hot and it may cause burns.
6
Control panel
6 2 4
3
7
Terminal panel
8 5
4 6 2
3
11 8 10 1213
9
1
10
5 7 1
9
1 POWER button (ON/STANDBY)
The status is changed between ON and STANDBY.
2 POWER indicator
3 MENU button
4 STATUS indicator
5 KEYSTONE/ENTER button
6 AUTO POSITION/p button
7 DIGITAL ZOOM/
W button
8 VOLUME/
T button
9 AV MUTE/
X button
10 SOURCE button
1 Power jack
2 COMPUTER/COMPONENT VIDEO IN terminal
(1, 2) (mini D-SUB 15-pin)
3 MONITOR OUT terminal (mini D-SUB 15-pin)
4 AUDIO IN terminal (mini jack)
5 AUDIO OUT terminal (mini jack)
6 S-VIDEO terminal
7 VIDEO terminal
8 SERIAL (RS-232C) terminal (D-SUB 9-pin)
9 Kensington Lock
10 LAN terminal (RJ-45)
11 HDMI terminal (1, 2) (HDMI 19-pin)
12 USB-B terminal
13 USB-A terminal
EN-7
Overview (continued)
Bottom side
1
1 Adjustment feet
Remote control
1
2
3
4
ON STANDBY
SOURCE SEARCH
AUTO
POSITION
MENU INFO.
ENTER
5
6
7
8
9
COLOR.E
3D ASPECT
KEYSTONE AV MUTE
MAGNIFY VOL FREEZE
TIMER EFFICIENT
MODE
14
15
16
17
18
19
20
10
11
12
13
1 ON button
2 SOURCE button
3 MENU button
4 ENTER button
5 COLOR.E button
6 KEYSTONE button
7 MAGNIFY button
8 DIGITAL ZOOM button
9 TIMER button
10 STANDBY button
11 AUTO POSITION button
12 SEARCH button
13 INFO. button
14
S, T, W, X buttons
15 3D button
16 ASPECT button
17 VOLUME UP, DOWN buttons
18 AV (Audio/Video) MUTE button
19 FREEZE button
20 EFFICIENT MODE button
EN-8
Remote control
Battery installation
Use two (AAA, R03) size batteries.
Inserting the batteries into the remote control
1. Remove the back cover of the remote control by pushing the battery compartment door in the direction of the arrow.
2. Load the batteries making sure that they are positioned correctly (+ to +, and - to -).
• Load the batteries from - spring side, and make sure to set them tightly.
3. Replace the back cover.
Removing the batteries from the remote control
Remove the back cover of the remote control and take out the batteries.
Caution:
• Use of a battery of wrong type may cause explosion.
• Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.
• Dispose of used batteries according to your local regulations.
• Before you dispose of the batteries, insulate them by placing insulation tape on the positive (+) and negative (-) terminals. If you dispose of the batteries together with other conductive objects such as a metal piece, they may short out, resulting in fire or explosion.
• Batteries may explode if misused. Do not recharge, disassemble, or dispose of in fire.
• Be sure to handle the battery according to the instructions.
• Load the battery with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.
• Keep batteries out of reach of children and pets. If children swallow the battery, see a doctor immediately.
• Remove the batteries, if the remote control is not used for a long time.
• Do not combine a new battery with an old one.
• If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with your eyes, rinse them with water and then consult your doctor.
• Do not carry or store the batteries together with metallic ballpoint pens, necklaces, coins, or hairpins. Otherwise they may short out, causing explosion or liquid leakage and resulting in fire or injury.
• Do not store the batteries where they are exposed to direct sunlight or subjected to high temperature and high humidity. High temperature and high humidity may cause corrosion or liquid leakage.
Operation range (of the remote control)
The maximum operation distance of the remote control is about 10 m (or about 32 feet) when the remote control is pointed at the remote control sensor of the projector. When the remote control is pointed to the screen, the distance from the remote control to the projector via the screen should be 5 m or less. However, the operation distance varies depending on the type of the screen used.
Reception angle (horizontal) Reception angle (vertical)
20°
10°
Reception angle (vertical), ceiling mount
30° 30°
ON STANDBY
SOURCE SEARCH
AUTO
POSITION
MENU INFO.
ENTER
COLOR.E
3D ASPECT
KEYSTONE AV MUTE
MAGNIFY VOL FREEZE
TIMER EFFICIENT
MODE
20°
Important:
• Do not expose the remote control sensor to direct sunlight or fluorescent. Keep a distance at least 2 m (6.5 feet) between the remote control sensor and the fluorescent light to ensure correct operation of the remote control.
Inverted fluorescent light, if located near the projector, may interfere the remote control.
• When you use the remote control too close to the remote control sensor, the remote control may not work correctly.
EN-9
Installation
Layout of TX20U
Image size varies depending on the distance between the screen and the projector.
A
SW
B
A=B
L
Diagonal size inch cm
120
150
200
250
300
40
60
80
100
305
381
508
635
762
102
152
203
254
Screen size
Width: SW inch
96
120
160
200
240
32
48
64
80 cm
244
305
406
508
610
81
122
163
203
Height: SH inch
72
90
120
150
180
24
36
48
60 cm
183
229
305
381
457
61
91
122
152 inch
156
195
260
325
390
51
77
103
129
Projection distance: L
Shortest (Wide) m
4.0
4.9
6.6
8.3
9.9
1.3
2.0
2.6
3.3
• The above figures are approximate and may be slightly different from the actual measurements.
Longest (Tele) inch
187
234
313
391
-
62
93
125
156 m
4.8
6.0
7.9
9.9
-
1.6
2.4
3.2
4.0
Layout of TW21U
Image size varies depending on the distance between the screen and the projector.
Diagonal size inch
120
150
200
250
40
60
80
100 cm
305
381
508
635
102
152
203
254
Screen size
Width: SW inch
102
127
170
212
34
51
68
85 cm
258
323
431
538
86
129
172
215
Height: SH inch
64
79
106
132
21
32
42
53 cm
162
202
269
337
54
81
108
135
Projection distance: L
Shortest (Wide) Longest (Tele) inch m
153
191
255
319
50
76
101
127
3.9
4.8
6.5
8.1
1.3
1.9
2.6
3.2
300 762 254 646 159 404 383 9.7
• The above figures are approximate and may be slightly different from the actual measurements.
inch
189
236
315
394
-
62
94
126
157 m
4.8
6.0
8.0
10.0
-
1.6
2.4
3.2
4.0
inch
10.8
13.5
18.0
22.5
27.0
3.6
5.4
7.2
9.0
Hd cm
27
34
46
57
69
9
14
18
23 inch
7.9
9.9
13.2
16.6
19.9
2.6
4.0
5.3
6.6
Hd cm
20
25
34
42
50
7
10
13
17
EN-10
Installation (continued)
When the aspect ratio of the screen is 4:3
When the aspect ratio of the screen is 4:3, the positional relation between the projected image and the screen is as shown on the right. Refer to the following table for installation.
Screen size
SW=W
When the aspect ratio of the image is 16:10 (WXGA)
Screen size Size of the projected image Projection distance
:
L
4:3 diagonal size inch cm
Width: SW inch cm
Height: SH inch
16:10 diagonal size
Width: W Height: H
Blank space:
B Shortest
(Wide) cm inch cm inch cm inch cm inch cm inch m
Longest
(Tele) inch m
40
60
80
100
120
150
200
102
152
203
254
305
381
508
32
48
64
80
96
120
160
81
122
163
203
244
305
406
24
36
48
60
72
90
120
61
91
122
152
183
229
305
38
57
75
94
113
142
189
96
144
192
240
288
359
479
32
48
64
80
96
120
160
81
122
163
203
244
305
406
20
30
40
50
60
75
100
51
76
102
127
152
191
254
2
3
4
5
6
8
10
5
8
10
13
15
19
25
47
71
96
120
144
180
240
1.2
1.8
2.4
3.0
3.7
4.6
6.1
59
89
118
148
178
223
297
1.5
2.2
3.0
3.8
4.5
5.7
2.5
3.8
5.0
6.3
7.5
9.4
7.5
12.5
Hd inch cm
6
10
13
16
19
24
32
250 635 200 508 150 381 236 599 200 508 125 318
300 762 240 610 180 457 283 719 240 610 150 381
13
15
32
38
301
361
7.6
9.2
372
-
9.4
-
15.6
18.8
40
48
• The above figures are approximate and may be slightly different from the actual measurements.
When the aspect ratio of the image is 16:9
40
60
80
100
Screen size Size of the projected image Projection distance
:
L
4:3 diagonal size inch cm
Width: SW inch cm
Height: SH inch
16:9 diagonal size
Width: W Height: H
Blank space:
B Shortest
(Wide) cm inch cm inch cm inch cm inch cm inch m
Longest
(Tele) inch m
102
152
203
254
32
48
64
80
81
122
163
203
24
36
48
60
61
91
122
152
37
55
73
92
93
140
187
233
32
48
64
80
81
122
163
203
18
27
36
45
46
69
91
114
6
8
3
5
120
150
200
250
305
381
508
635
96
120
160
200
244
305
406
508
72
90
120
150
183
229
305
381
110
138
184
229
280
350
466
583
96
120
160
200
244
305
406
508
54
68
90
113
137
171
229
286
9
11
15
19
300 762 240 610 180 457 275 699 240 610 135 343 23
• The above figures are approximate and may be slightly different from the actual measurements.
57
23
29
38
48
8
11
15
19
140
175
234
293
351
46
69
93
116
173
217
289
361
-
57
86
115
144
3.6
4.4
5.9
7.4
8.9
1.2
1.8
2.4
3.0
4.4
5.5
7.3
9.2
-
1.5
2.2
2.9
3.7
Hd inch cm
10.5
13.1
17.5
21.9
26.3
3.5
5.3
7.0
8.8
27
33
44
56
67
9
13
18
22
EN-11
Installation (continued)
When entire projected image isn’t displayed within the screen
(DIGITAL ZOOM)
To adjust the projected image size and position, use
DIGITAL ZOOM function.
1. Press the DIGITAL ZOOM button.
• The DIGITAL ZOOM menu appears at the center of the screen.
SHIFT
ENTER: DIGITAL ZOOM
Adjustable in any of four directions
DIGITAL ZOOM
10
ENTER: SHIFT
2. Press the + or - button to adjust the projected image size.
• Every time the + button is pressed, the projected image becomes larger.
• Every time the - button is pressed, the projected image becomes smaller.
• Projected image is a maximum as factory default
(0).
Original image size
(= maximum image size)
Reduced image
DIGITAL ZOOM
10
ENTER: SHIFT
3. Press the ENTER button.
• The SHIFT menu appears at the center of the screen.
SHIFT
ENTER: DIGITAL ZOOM
4. Press the
S,T,W or X button to move the projected image position.
• Every time the
S button is pressed, the projected image moves up.
• Every time the
T button is pressed, the projected image moves down.
• Every time the
W button is pressed, the projected image moves to the left.
• Every time the
X button is pressed, the projected image moves to the right.
Important:
• When you reduce the projected image using the
DIGITAL ZOOM function, the resolution decreases.
In addition, stripes may appear or straight lines may bend in images with complicated patterns.
• When you use DIGITAL ZOOM and KEYSTONE in combination, the adjustable range becomes narrower than that when these functions are used individually.
Changing the AUTO POWER OFF setting
The AUTO POWER OFF function of this projector is enabled by default.
Change the AUTO POWER OFF setting as necessary.
To change the AUTO POWER OFF setting:
(See page 25 for menu setting.)
1. Display the INSTALLATION menu.
2. Select AUTO POWER OFF by pressing the
S or T button.
3. Select your desired item by pressing the
W or X button.
Important:
• This function does not work when the input source is
LAN DISPLAY, USB DISPLAY or USB VIEWER.
• The AUTO POWER OFF function does not work during AV MUTE.
Setting IMAGE REVERSE
Set IMAGE REVERSE in the INSTALLATION menu according to the orientation of the projector. The default setting is OFF.
• Select OFF for the combination of floor installation and front projection.
• Select MIRROR INVERT for the combination of ceiling installation and front projection.
• Select MIRROR for the combination of floor installation and rear projection.
• Select INVERT for the combination of ceiling installation and rear projection.
(See page 25 for menu setting.)
1. Display the INSTALLATION menu.
EN-12
Installation (continued)
2. Select IMAGE REVERSE by pressing the
S or T button.
3. Select OFF, MIRROR, INVERT or MIRROR INVERT by pressing the
W or X button.
Front projection, ceiling mounting
For ceiling mounting, you need the ceiling mount kit designed for this projector. Ask a specialist for installation. For details, consult your dealer.
• The warranty on this projector does not cover any damage caused by use of any non-recommended ceiling mount kit or installation of the ceiling mount kit in an improper location.
in addition to the mount kit fixing screws to prevent the projector from falling due to an earthquake or other cause. For that purpose, use a metal bar, wire, or screw that bears a load of at least 40kgf. When using a metal wire, secure one end to a screw hole marked with an arrow on the rear terminal panel and the other end to the mount kit. (Don’t use screw holes without arrow marks.) On this case, make sure that the screw is inserted in the projector at least
5mm. The length of the screw should be 20 mm or shorted. Also make sure that no electrical current is flowing in the mount kit due to current leakage or other cause.
Rear projection
Ask a specialist for installation. For details, consult your dealer.
• When using the projector mounted on the ceiling, set IMAGE REVERSE in the INSTALLATION menu to
• When the projector is mounted on the ceiling, images may appear darker than those projected in the case of tabletop mounting. This isn’t a product malfunction.
Ceiling mount installation
If you wish to install the projector using a ceiling mount, please use the screw holes as the illustration shows.
Important:
• Screws are not included. Please obtain the appropriate screws for your type of ceiling. (M4 diameter)
• It is recommended that you keep a reasonable space between the bracket and the projector to allow for proper heat distribution.
Caution:
• Installation must be done by a qualified professional.
When the project is installed on the ceiling using the ceiling mount kit, it is recommended to hold the mount kit and the projector using a metal bar or wire
• For rear projection, set IMAGE REVERSE in the
INSTALLATION menu to MIRROR. See page 28.
Caution:
• Placing the projector directly on a carpet impairs ventilation by the fans, causing damage or failure.
Put a hard board under the projector to facilitate ventilation.
• Place the projector at least 50 cm (or 20 inch) away from the wall to prevent the air inlet grille and the air outlet grilles that emit hot air from being blocked.
• Do not use the projector in the following locations and manners, which may cause fire or electric shock.
• In a dusty or humid place.
• In a sideways or upside-down position.
• Near a heater.
• In an oily, smoky, or damp place such as a kitchen.
• In direct sunlight.
• Where the temperature rises high, such as in a closed car.
• Where the temperature is lower than +41°F (or
+5°C) or higher than +95°F (or +35°C ).
Important:
• Do not apply force to the lens, because the lens may be damaged.
• Be sure to use this projector at an altitude of less than 1500 meters.
EN-13
Basic connections
This projector can be connected with various devices such as a VCR, video camera, videodisc player, and personal computer that have analog RGB output connectors.
Important:
• Make sure that the connected device is turned off before starting connection.
• Plug in the power cords of the projector and the connected devices firmly. When unplugging, hold and pull the plug. Do not pull the cord.
• When the projector and the connected devices are located too close to each other, the projected image may be affected by their interference.
• See the owner’s guide of each device for details about its connections.
Projector + AV device
S-VIDEO
(option)
VIDEO
(option)
AUDIO IN
(option)
To audio output (L)
To audio output (R)
To video output
To S-video output
Important:
• Match the colors of the video and audio plugs on the Audio cable with those of the terminals.
• Speaker output is mono.
Projector + DVD player or HDTV decoder
Some DVD players have an output connector for 3-line fitting (Y, C
B
, C
R
). When connecting such DVD player with this projector, use the COMPUTER/COMPONENT VIDEO IN terminal.
Audio cable (option)
DVD player or HDTV decorder
To audio output
BNC - RCA connector (option)
No connection
B R G
COMPUTER IN
Mini D-SUB 15-pin - BNC conversion cable (option)
Important:
• The terminal’s names Y, P
B
, and P
R
are given as examples of when a HDTV decoder is connected.
• The terminal’s names vary depending on the connected devices.
• Use a Mini D-SUB 15-pin - BNC conversion cable for connection.
• Image may not be projected correctly with some DVD players.
• When connecting a HDTV decoder having RGB output terminals, set COMPUTER INPUT to RGB in the SIGNAL menu.
EN-14
Basic connections (continued)
Connection (for video equipment having an HDMI terminal)
Equipment having an
HDMI terminal to HDMI IN 1 terminal or HDMI IN 2 terminal
HDMI (with HDMI logo) cable (option)
Important:
• Use a commercially available HDMI (with HDMI logo) cable.
• You don’t have to connect any cable for audio input. You can input video and audio using an HDMI cable only.
• When HDMI audio isn’t output, it may be output by turning off the power of the video equipment with the projector and the video equipment connected to each other and then turning back on the power.
• Some cables may not be connected correctly depending on the size and shape of their connectors.
• To connect the projector and video equipment via a distributor, use a Deep Color supported distributor compliant with HDMI1.3 or higher (or a 3D display supported distributor compliant with HDMI1.4 or higher when displaying
3D images.)
When you connect this projector and a Digital device (such as a DVD player) via the HDMI terminal, black color may appear dark and deep, depending on the type of the connected device.
• This depends on the black level setting of the connected device. There are two kinds of methods to digitally transfer image data, in which different black level settings are employed respectively. Therefore, the specifications of the signals output from DVD players differ, depending on the type of the digital data transfer method they use.
• Some DVD players are provided with a function to switch the methods to output digital signals. When your DVD player is provided with such function, set it as follows.
EXPAND or ENHANCED
J NORMAL
• See the users guide of your DVD player for details.
• When your digital device does not have such function, set INPUT LEVEL to ENHANCED in the ADVANCED MENU of the IMAGE menu of this projector, or adjust the black color by viewing the image.
EN-15
Basic connections (continued)
Projector + Computer
For computer with Mini D-SUB
Computer cable
COMPUTER IN
AUDIO OUT
Audio cable (option)
AUDIO IN
Necessary when outputting to both a
PC monitor and the projector.
MONITOR OUT
Computer cable
(option)
To monitor port
For analog connection:
1. Connect one end of the supplied computer cable to the COMPUTER/COMPONENT VIDEO IN terminal (1, 2) of the projector.
2. Connect the other end of the computer cable to the monitor port of the computer.
For monitor connection:
Connect the computer cable from the monitor to the MONITOR OUT terminal of the projector.
• Images may not be displayed correctly depending on the type of the input signal. See the instruction manual of the monitor.
• Signals are coming from the COMPUTER/COMPONENT VIDEO IN-1 terminal of the projector.
• When the STANDBY MODE in the INSTALLATION menu is set to STANDARD the MONITOR OUT terminal outputs signals during standby mode.
Important:
• When you use a longer computer cable instead of the provided cable, the image may not be projected correctly.
• Some computers require additional connectors or analog RGB output adapters to be connected with this projector.
Contact your dealer for further information.
• This projector uses stereo mini jack for its audio input. Check the type of the audio output terminal of the connected computer and prepare a proper cable for connection. Some computers don’t have the audio output terminal.
• Speaker output is mono.
• When the audio cable is connected to the AUDIO OUT terminal, the speaker output is muted.
• The audio output can be available during power standby.
For Mac computers
• If your Mac computer has no video port, a monitor output adapter is required. Contact your dealer for further information.
• Some Mac computers require a MAC adapter for the computer cable for connection with this projector. Contact your dealer for further information.
About DDC
The COMPUTER/COMPONENT VIDEO IN terminals (1,2) of this projector comply with the DDC 1/2B standard. When a computer supporting this standard is connected to this terminal, the computer will automatically load the information from this projector and prepare for output of appropriate images.
• After connecting a computer supporting this standard to this terminal, plug the power cord of the projector in the wall outlet first, and then boot up the computer.
EN-16
Preparation
Preparation for projection
1. Attach the provided power cord to the projector.
2. Plug the power cord in the wall outlet.
Warning:
• Do not look into the lens directly when the projector is on.
• One of power cords for the U.S., Europe, U.K.,
Australia, and South Korea is provided appropriately.
• This projector uses the power plug of three-pin grounding type. Do not remove the grounding pin from the power plug. If the power plug doesn’t fit your wall outlet, ask an electrician to change the wall outlet.
• In case that the power cord for the U.S. is provided with this projector, never connect this cord to any outlet or power supply using other voltages or frequencies than rated. If you want to use a power supply using other voltage than rated, prepare an appropriate power cord separately.
• Use 100-240 V AC 50/60 Hz to prevent fire or electric shock.
• Do not place any objects on the power cord or do not place the projector near heat sources to prevent damage to the power cord. If the power cord should be damaged, contact your dealer for replacement because it may cause fire or electric shock.
• Do not modify or alter the power cord. If the power cord is modified or altered, it may cause fire or electric shock.
Caution:
• Plug in the power cord firmly. When unplugging, hold and pull the power plug, not the power cord.
• Do not plug in or out the power cord with your hand wet. It may cause electric shock.
Important:
• When STANDBY MODE in the INSTALLATION menu is set to STANDARD, the fans rotate at very low speed during standby after plugging the power cord
(with 5 second high speed rotation at the beginning) and after turning off the lamp. This is to cool down the projector operating various functions during standby and is not a malfunction. (When STANDBY
MODE is set to LOW or LAN, the fans stop during standby.)
Adjustment of the projection angle
For the best projection, project images on a flat screen installed at 90 degrees to the floor. If necessary, tilt the projector using the two adjustment feet on the bottom of the projector.
Using the adjustment feet (front)
1. Tilt up the projector to the appropriate angle.
2. Rotate the adjustment feet (front) for fine adjustment.
EN-17
Important:
• Install the screen on a flat wall at 90 degrees to the floor.
• Slanting the projector more than ±10° (right and left) or ±15° (front and rear) may cause trouble or explosion of the lamp. You can tilt the projector up to
7 degrees using the adjustment feet only.
• Images may not be projected in a shape of a regular rectangle or with its aspect ratio 4:3, depending on the installation conditions of the projector and the screen.
When projected images are distorted to a trapezoid
When AUTO KEYSTONE in the INSTALLATION menu is set to ON, this projector automatically corrects vertical keystone distortion. For fine adjustment, press the
KEYSTONE button on the projector or the remote control to display KEYSTONE, and adjust the image by pressing the
S,T button (or +, - button on the remote control).
KEYSTONE menu
You can correct the distortion vertically focusing on the screen center.
In the following cases:
Press the S or + button.
Press the T or - button.
Preparation (continued)
Important:
• The automatic keystone adjustment may not be carried out correctly because of the ambient temperature and the installation conditions of the projector and the screen. In such cases, correct the keystone manually.
• When the projector is projecting images where acceleration is present, such as in a vehicle and aircraft, the automatic keystone adjustment may not function correctly. In such a case, set AUTO
KEYSTONE in the INSTALLATION menu to OFF and correct the keystone manually.
• When the KEYSTONE-mode adjustment is carried out, the adjustment value is indicated. Note that this value doesn’t mean a projection angle.
• When the KEYSTONE-mode adjustment takes effect, the resolution decreases. In addition, stripes may appear or straight lines may bend in images with complicated patterns. They are not due to product malfunctions.
• When the KEYSTONE-mode adjustment is performed, the displayed image may be distorted.
• Noise may appear on the screen during the
KEYSTONE-mode adjustment because of the type of the video signal being projected and the setting values of the KEYSTONE-mode adjustment. In such cases, set the KEYSTONE-mode adjustment values in the range where the image is displayed without noise.
• When the KEYSTONE-mode adjustment is performed, the menu display is distorted. To relieve such symptom, set the MENU POSITION to center.
• When you use DIGITAL ZOOM and KEYSTONE in combination, the adjustable range becomes narrower than that when these functions are used individually.
EN-18
Basic operation
4. Focus
6. Zoom
3, 1, 2
5
3
5
ON STANDBY
SOURCE SEARCH
AUTO
POSITION
MENU INFO.
ENTER
1, 2
COLOR.E
3D ASPECT
KEYSTONE AV MUTE
MAGNIFY VOL FREEZE
TIMER EFFICIENT
MODE
Power-on
1. Turn on the device connected to the projector first.
2. Plug the power cord in the wall outlet.
• The POWER indicator lights up.
• If the power cord is unplugged from the wall outlet before the projector is cooled down completely after use, the fans may start rotating when the power cord is plugged in next time and the
POWER button may not function. In this case, wait for the fans to stop and press the POWER button to light the indicator.
3. Press the POWER button on the control panel or the
ON button on the remote control.
• It may take about one minute for the lamp to light up.
• The lamp occasionally fails to light up. Wait a few minutes and try to light the lamp again.
• After the POWER button is pressed, the image may flicker before the lamp becomes stable. This is not a product malfunction.
• Regardless of the setting of LAMP MODE in the
INSTALLATION menu, the STANDARD lamp mode is activated by default whenever the projector is turned on. The LAMP MODE is set to either
STANDARD or LOW depending on the setting last selected, and you cannot switch the LAMP MODE in about one minute after the lamp is on.
• Furthermore, you cannot switch LAMP MODE
LOW1 to LOW2 in about three minutes after the lamp is on.
Indicator
STATUS POWER
Condition
Stand-by
When the lamp is on.
-
Green
Red
Green
Important:
• If the lamp exceptionally turned off due to the power interruption or voltage drop, it can happen that the lamp does not turn on even if you switch again the power supply on. In that case, please pull the electric cord out of the consent and put it again in the consent about 10 minutes later.
EN-19
• Do not cover the lens while the lamp is on.
• The projector starts warming up when the POWER button is pressed. During the warm-up process, images may appear dark and no commands are accepted.
• By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp
when the STATUS indicator blinks red. (See page
• Images may not be projected with good quality in an extremely hot or cold environment. (This is not a product malfunction.)
• In order to ensure the safety in case of trouble with the projector, use an electrical outlet having an earth leakage breaker to supply the power to the projector.
If you do not have such outlet, ask your dealer to install it.
4. Adjust the focus by turning the focus ring.
• You are recommended to adjust the focus at the screen center.
5. Select an input source.
• Press the SOURCE button.
• When the SOURCE button is pressed, the SOURCE dialog shown right appears. Press the
S or T button to select an input and press the
ENTER button.
• The projector automatically selects the appropriate signal format. The selected signal format is displayed on the screen.
• You cannot change the input source while the menu is being displayed.
• Though it may take some time before an image is displayed on the screen depending on the type of the input signal, such symptom is not a malfunction.
• Images may not be projected in the correct position, depending on the type of the input signal. In such a case, press the AUTO POSITION button. (The AUTO POSITION only works when
the input is COMPUTER (1 or 2).) (See page 21.).
• When COMPUTER 1 or COMPUTER 2 is chosen as the source, images supplied from the computer may flicker. Press the
W or X button on
Basic operation (continued)
the remote control to reduce flicker, if it occurs.
(Fine adjustment).
• To avoid permanently imprinting a fixed image onto your projector, please do not display the same stationary images for long period.
6. Adjust the image size by turning the zoom ring.
• If necessary, adjust the focus and zoom again.
When fine streaks are seen on projected images
This is due to interference with the screen surface and is not a malfunction. Replace the screen or displace the focus a little.
Detect input signal and switch the projected image automatically (SEARCH)
You can also switch the projected image by pressing the SEARCH button on the remote control. The projector starts to search for signals which are being input to each input source automatically.
• When two or more input signals are input, repeat pressing the SEARCH button until the target image is projected.
• If input signal can not be detected, the projector returns to the input source when pressed the
SEARCH button.
Important:
• When you connect the equipments such as computer, DVD player, or Blu-ray player, turn on their equipments before this operation
• Input signals may not be detected depending on the type of equipments. It also may not be detected when unsupported signals are input, or when computer is starting-up.
Power-off
Use the following procedure to turn off the projector.
The lamp may deteriorate if the projector is powered off and on repeatedly within 30 minutes after the lamp is lighted.
1. Press the POWER button on the control panel or the
STANDBY button on the remote control.
• The message “POWER OFF? YES: PRESS
AGAIN” appears on the screen.
• To cancel, press any button except the POWER button.
(Some buttons on the remote control don’t function for cancel.)
2. Press the POWER button on the control panel or the
STANDBY button on the remote control within 10 seconds again.
• The lamp will go out and the STATUS indicator will start blinking.
3. Wait about 90 seconds for the STATUS indicator to be turned off.
4. Unplug the power cord.
• The POWER indicator will go out.
• If the power cord should be unplugged accidentally while either the STATUS indicator is blinking or the lamp is on, allow the projector to cool down for 10 minutes with the power off. To light the lamp again, press the POWER button (or
ON button). If the lamp doesn’t light up immediately, repeat pressing the POWER button
(or ON button) two or three times. If it should still fail to light up, replace the lamp.
Caution:
• The lamp can’t be lit again for one minute after turned off for safety purpose. It will take another one minute for the STATUS indicator to go out. If you want to turn on the projector again, wait until the indicator goes out, and then press the POWER button.
• The air outlet fans rotate faster as the temperature around the projector rises.
• When the temperature around the projector rises high, the sign “TEMPERATURE!!” blinks red on the screen. If the temperature stays high, the lamp will go out automatically.
Important:
• When storing the projector in the carrying case, the lens should face up.
Before carrying the projector, rotate the focus ring and zoom ring to adjust the lens to the shortest. This prevents the possible damages of the lens.
Direct Power OFF
You can turn off this projector just by unplugging the power cord without pressing the POWER button.
• Don’t shut down the projector while the STATUS indicator is blinking after the lamp lights up because the lamp’s life may be shortened.
• Don’t turn the projector back on right after shutting it down because the lamp’s life may be shortened.
(Wait about 10 minutes before turning the projector back on.)
• Before shutting down the projector, be sure to close the menu screen. If you shut down the projector without closing the menu, the setting data of the menu may not be saved.
• If you shut down the projector while controlling the projector using the network function, the application software such as ProjectorView may fail. For details, see “User Manual of LAN Control Utility” contained in the CD-ROM.
EN-20
Basic operation (continued)
AUTO POSITION button
When the image isn’t projected in the right position with
Computer selected as the input source, follow the procedure below.
1. Project an image containing a lot of characters without black areas. (For example, display a window containing a lot of characters in the full-screen mode.)
2. If the screen saver is running, turn it off.
3. Press the AUTO POSITION button.
• If the image is still not in the right position, adjust the image position using the SIGNAL menu. See
page 30. (For details, see the flowchart on page
Volume from the speaker
Press the VOLUME + or - button on the remote control or VOLUME button on the projector. The volume control bar will appear on the screen. Press the VOLUME +, -,
W or X button while the volume control bar is displayed to adjust the volume.
• The volume control bar will disappear about 10 seconds after the VOLUME button is released.
• The VOLUME buttons don’t function while the menu is being displayed.
• When a high-level audio signal, such as a DVD audio signal, is supplied to the AUDIO IN terminal, the output from the speaker may be distorted.
• When the audio cable is connected to the AUDIO
OUT terminal, the speaker output is muted.
• The volume of the audio from the AUDIO OUT terminal is also changed by pressing the VOLUME buttons.
• The VOLUME value varies within the range between
0 and 21.
You can change the volume during power standby by pressing VOLUME + or - button when STANDBY MODE in the INSTALLATION menu is set to STANDARD.
(See page 25 for menu setting.)
Blanking the screen temporarily (AV mute)
The video and audio signals are temporarily muted when the AV MUTE button is pressed. To cancel muting, press the AV MUTE button again.
• The audio from the AUDIO OUT terminal is also muted by pressing the AV MUTE button.
• The AUTO POWER OFF function does not work during AV MUTE.
Important:
• The AV MUTE TIMER function of this projector is enabled by default. AV MUTE is automatically canceled when the muting continues for one hour.
Change the AV MUTE TIMER setting as necessary.
Setting the aspect ratio
You can change the aspect ratio of the input video signal (or the ratio of width to height of the image).
Change the setting according to the type of the input video signal.
How to change the settings:
With the remote control:
1. Press the ASPECT button.
• Every time the ASPECT button is pressed, the aspect mode changes from NORMAL to 16:9, to
FULL, and back to NORMAL.
- NORMAL:
Select to change the aspect ratio automatically depending on the input signal. (Select this option for normal use.)
- 16:9:
Select to expand squeezed (or horizontally compressed) images such as DVD images to
16:9.
- FULL:
Select to project images in full size irrespective of type of input signal.
With the FEATURE menu:
(See page 25 for menu setting.)
1. Display the FEATURE menu.
2. Select ASPECT by pressing the
S or T button.
3. Select your desired aspect ratio by pressing the
W or
X button.
When 16:9 is selected with FEATURE menu, you can make further settings using the following procedures.
4. Press the ENTER button.
5. Select an item you want to set by pressing the
S or
T button and select a setting by pressing the W or
X button.
• POSITION: (for TX20U only)
You can select the image display position within the screen from UPPER, CENTER, and LOWER.
• MODE:
You can select whether or not to display signals at 16:9 depending on their type.
- ALL SIGNALS:
All signals are always displayed at 16:9 irrespective of their type.
EN-21
Basic operation (continued)
- VIDEO ONLY:
Signals supplied from video devices only are displayed at 16:9.
To cancel the menu:
6. Press the MENU button.
Important:
• When a 16:9 image is kept displayed for a long time before displaying 4:3 image, the afterimages of the black bars may appear on the 4:3 image screen.
Consult your dealer in this case.
When connecting to a laptop computer:
When the projector is connected to a laptop computer, images may not be projected in some cases. In such cases, set the computer so that it can output signals externally. The setting procedure varies depending on the type of the computer. See the instruction manual of your computer.
Example of the setting procedure for external output
Press the [Fn] key and any of the keys [F1] to [F12] at the same time. (The key to be pressed depends on the type of the computer you use.)
Setting of the resolution
If the resolution of the computer doesn’t match with that of the projector, projected images may be obscured. Ensure that their resolutions are the same
(see page 79). For the method to change the output
resolution of the computer, contact the manufacturer of the computer.
Watching 3D content
You can enjoy 3D content with this projector.
In order to watch 3D content, you need to have the following items:
• 3D images inputted from a computer, DVD player,
Blu-ray player, etc.
• DLP™ Link™ active 3D glasses
Important:
• Some 3D glasses may not work with this projector.
Ask the dealer for details.
This projector supports the following 3D image formats:
• Frame packing:
The format which transmits the images maintaining the original resolution including the signals for right and left.
• Side by side:
The format which displays the images with the half of the original resolution for the left eye and the right eye side-by-side in one frame.
• Top and bottom:
The format which displays the images with the half of the original resolution for the left eye and the right eye at the top and bottom in one frame.
• Frame sequential (Field sequential):
The format which displays alternately the images for the left eye and the right eye.
3D image format
Side by side Top and bottom Frame packing
L
L R
L
R
Frame sequential
(Field sequential)
L
R
L
R
R
DLP™ Projector
Sensor
The shutter timing of the 3D glasses is controlled by being synchronized with switching of right and left
3D image which is detected by the sensor of glasses.
R
L
DLP™ Link™ active
3D glasses
For details about the supported 3D image signal
formats, see "3D supported signal" on page 80.
To view 3D images:
Preparation:
• Switching the 3D mode (such as 3D setting system) of the player may be required when projecting 3D images from the player supporting 3D display. Read the user manual of the player for details.
1. Project a 3D image on the screen inputted from a computer, DVD player, or Blu-ray player.
2. Display the IMAGE menu. (See page 25 for menu
settings.)
3. Press the
S or T button to select 3D.
4. Press the
W or X button to select ON .
5. Press the ENTER button.
EN-22
6. Press the
S or T button to select 3D FORMAT.
7. Press the
W or X button to select the setting appropriate for the input signal and press the ENTER button.
• AUTO (for HDMI input only):
Select this setting normally when 3D images are inputted from the HDMI1 or HDMI2 terminal. (3D images are displayed automatically when the input signal includes the 3D identification signal.)
• SIDE BY SIDE :
Select this setting when 3D images are inputted in the side by side format.
• TOP AND BOTTOM :
Select this setting when 3D images are inputted in the top and bottom format.
• FRAME SEQUENTIAL
Select this setting when 3D images are inputted in the frame sequential format.
8. Turn the power switch on the 3D glasses to ON and wear the 3D glasses.
Basic operation (continued)
9. If the contents are not projected correctly, repeat step 1 to 5, press the
W or X button to select 3D
FORMAT and switch 3D SYNC INVERT to ON.
Important:
• You cannot project the 3D content from the input source LAN DISPLAY, USB DISPLAY, and USB
VIEWER.
• You can select the 3D setting also by using the 3D button on the remote control. Press the 3D button to select the setting and press the ENTER button.
• Even when the 3D option is set to AUTO and a 3D image is inputted from the HDMI1 or HDMI2 terminal, the 3D image is not displayed if the input signal does not include the 3D identification signal.
In such a case, change the setting to SIDE BY SIDE
, TOP AND BOTTOM , or FRAME SEQUENTIAL
according to the format of the input signal.
•
The signals listed in the table on page 80 can be
displayed in 3D format. You cannot view other signals in 3D format even when you set 3D FORMAT in the 3D menu to AUTO , SIDE BY SIDE , TOP
AND BOTTOM , or FRAME SEQUENTIAL .
• If the viewing distance is nearer than the recommended distance, it will cause physical discomfort and eye fatigue.
• Watch the contents in front of the screen, not at big angle. If you are viewing the screen at big angle, you may not be able to view 3D contents correctly.
• If you are not viewing 3D contents correctly, check to see if the 3D glasses are powered on or adequately charged. See the instruction manual of the 3D glasses for more information.
• There are personal differences in viewing the 3D images. For persons with myopia, hypermetropia, astigmatism or left and right sights, please wear glasses to correct them then wear the 3D glasses.
• The picture seems misplaced at the start of projecting the 3D images, however, this is not a malfunction.
• With the 3D FORMAT option set to to AUTO , SIDE
BY SIDE , TOP AND BOTTOM , or FRAME
SEQUENTIAL , 3D images displayed on the projector appear darker. It is normal and does not mean the projector is malfunctioning.
• The following features cannot be used when viewing
3D images on the projector:
• OVER SCAN and SHUTTER in the SIGNAL menu
• MAGNIFY mode
• It may occur that the image may not be enough 3D image because setting such as fluorescent lighting may occur loss of synchronism of glasses.
• 3D image may not appear on the screen depending on the PC performance such as graphics board, memory, or CPU.
• If DVD is run by 480p signals, 3D image may not be displayed correctly depending on the DVD player.
• When 3D image is projected on the screen in 120Hz or using certain type of playback software of PC, the image may not appear on the screen.
• 3D image may not be displayed properly depending on the settings, functions, or manner of connection of the DVD player or Blu-ray player.
EN-23
Caution:
Notes on danger to public health during watching
3D image
• Stop viewing the 3D image immediately if you feel tired, discomfort, or any other abnormality. It may cause you to feel unwell if continuing to watch the
3D image in such cases. Please take the necessary rest, do not continue watch the 3D image for a long time. Stop using the 3D glasses if you can clearly see double images when viewing 3D content.
Prolonged use may cause eyesight fatigue.
• The following people need to refrain from use as with
2D image.
• a photosensitive patient
• a patient with heart disease
• a person in poor physical condition
• a sleepy person
• a very tired person
• a drunk person
• children
• When watching 3D movies, take an appropriate break after watching a movie. When watching 3D content on interactive devices such as 3D games or computers, take an appropriate break every 30-60 minutes. Prolonged use may cause eyesight fatigue.
• When you feel uncomfortable, stop viewing 3D images and playing 3D games until you are restored.
If necessary, consult a doctor. Also, stop driving a car until you are restored (for about 2 hours). The period to restore varies with the individual.
• As a guide, 3D glasses should not be used by children younger than 5 - 6 years old. As it is difficult to judge younger children’s reactions to fatigue or discomfort, their physical condition may deteriorate suddenly. When this product is being used by a child, the parent or guardian should check to ensure that the child’s eyes are not becoming tired.
• When viewing the pictures that roll over and shake or many dynamic pictures, if you feel uncomfortable, please look at another place.
• When viewing contents with movements such as rotation, or horizontal or vertical oscillation, you may feel as if you are actually moving. If such a feeling results in discomfort, look away from the screen.
• When using the 3D glasses, be careful not to strike the screen or other people by mistake. As the images are in 3D, you may mistake the distance from the screen, causing to strike the screen which may result in injury. When using the 3D glasses, do not place breakable objects near the glasses. You may move by mistaking the 3D objects you are viewing as the real objects, causing damages to surrounding objects that may lead to injury.
• When using the 3D glasses, make sure your eyes are on an approximate horizontal level. If you suffer from myopia (short sightedness), hyperopia (farsightedness), astigmatism, or have eyesight differences between the left and right eyes, please use corrective glasses or other such methods to correct your eyesight before putting on the 3D glasses.
• When you view the 3D images, keep a distance from the screen of about three times the effective height of the screen.
Menu operation
You can make various settings using the displayed menus.
Following 6 menus are displayed.
IMAGE menu (pages 26 and 27) INSTALLATION menu (pages 27 and
FEATURE menu (page
EN-24
Menu operation (continued)
How to set the menus
1. Press the MENU button.
• The menu selection bar is displayed appears on the screen.
Selectable menus are displayed by icons. (The menu icon being selected is displayed on a blue background.)
The name of the menu being selected is displayed.
2. Press the
W or X button to select a menu to use.
3. Press the ENTER button (or
T button).
• The selected menu is displayed.
The item being selected is displayed in red letters.
4. Press the
S or T button to select an item to adjust.
5. Set the selected item by pressing the
W or X button.
6. To cancel the menu, press the MENU button several times.
Important:
• When an item marked with “ ” is selected, pressing the ENTER button makes its value effective or displays another screen for further setting.
• When the MENU button doesn’t function, unplug the power cord from the wall outlet. Wait about 10 minutes, plug the power cord in, and try again.
• The menus and screens shown in this manual may be different from those of the actual projector.
EN-25
Menu operation (continued)
Menu items
Set the following items provided in the respective menus.
IMAGE menu
ITEM SETTING
COLOR ENHANCER AUTO
PRESENTATION
STANDARD
THEATER
BLACK BOARD
WHITE BOARD
FUNCTION
Select to optimize the settings automatically depending on the input signal.
(Select this option for normal use.)
Select to make the displayed image look bright and crisp.
Select to make the displayed image look natural.
This option, suitable for viewing movies, makes the displayed image look soft and smooth.
Reproduces natural color tones when images are projected directly onto a black board.
Reproduces natural color tones when images are projected directly onto a white board.
Select to set the BrilliantColor
™
and GAMMA MODE. (See page 37.)
Use to adjust the contrast of the projected image. (See page 35.)
Use to adjust the brightness of the projected image. (See page 35.)
Select from the predetermined color temperatures.
CONTRAST
BRIGHTNESS
COLOR TEMP.
COLOR
MANAGEMENT
COLOR
TINT
SHARPNESS
3D
3D FORMAT
USER
±30
±30
STANDARD / LOW /
HIGH
USER
ENTER
±10
±10
±5
ON
AUTO
/ OFF
SIDE BY SIDE
TOP AND BOTTOM
FRAME SEQUENTIAL
3D SYNC INVERT ON / OFF
Use to adjust the color temperature to a desired value. (See page 36.)
The COLOR MANAGEMENT MENU is displayed. Select to emphasize only certain colors or to correct the tonal deviation of only certain colors.
Use to adjust the color thickness of the projected image. (See page 35.)
Use to adjust the color tint of the projected image. (See page 35.)
Use to adjust the sharpness of the projected image. (See page 35.)
Set to ON/OFF of 3D display.
Automatically distinguishes the type of the input signal and displays 3D images when 3D image signals are inputted or 2D images (normal images) when 2D image signals are inputted (only when the signal from the HDMI1 or
HDMI2 terminal is inputted).
Select this setting when 3D images are inputted in the side by side format.
Select this setting when 3D images are inputted in the top and bottom format.
Select this setting when 3D images are inputted in the frame sequential format.
Switches the order of the image for left eye and for right eye.
EN-26
Menu operation (continued)
IMAGE menu (continued)
ITEM
ADVANCED MENU
INPUT LEVEL
SETTING
ENTER
AUTO /NORMAL/
ENHANCED
FUNCTION
The ADVANCED MENU is displayed for the following settings.
For HDMI signal input:
AUTO: The proper setting is automatically selected.
NORMAL: Select when grayish black occurs.
ENHANCED: Select when solid black occurs.
Does not display captions.
CLOSED CAPTION OFF
CC1 / CC2 / CC3 /CC4
/ T1 / T2
Displays captions.
• When the setting of COLOR ENHANCER or 3D is changed, the displayed image may be disturbed.
• When the COMPUTER1, COMPUTER2, HDMI1, HDMI2, LAN DISPLAY, USB DISPALY or USB VIEWER is selected as the input source, COLOR and TINT can’t be adjusted.
• TINT is available only when the NTSC signal is input.
• INPUT LEVEL is unavailable when the digital signal is supplied from the YC
B
C
R
/YP
B
P
R
terminal of the connected device.
• Captions are not displayed while information about the menu or input signal selection is being displayed on the screen.
• The closed caption function displays text information included in the NTSC signal, which is mainly used for TV broadcasting in
North America.
INSTALLATION menu
ITEM
LAMP MODE
SETTING
STANDARD
LOW
STANDBY MODE STANDARD
LAN
LOW
FUNCTION
Select this option when you want to view images in a well-lit room.
Select this option to moderate the intensity of the lamp. The operating sound is reduced and the lamp lifetime becomes longer.
• When this mode is swithed, projector images may flicker.
• If this mode is frequently switched, the lamp may be deteriorated.
• When LOW mode is swithed, LOW1 is selected automatically as default.
Press Enter button and select LOW2 to moderate the intensity of the lamp more than LOW1. The operating sound is reduced more than LOW1.
• When this mode is swithed, projector images may flicker.
• If this mode is frequently switched, the lamp may be deteriorated.
• During LOW2 is switched, projector images are little bit flickering for a moment with constant timing to keep lamp condition well.
• During LOW2 is switched, fan speed increase for a short time once per 30 minutes to keep lamp condition well.
Select this option when you control the projector via the LAN terminal during power standby. Audio is output from the AUDIO OUT terminal. Video signal is output from the MONITOR OUT terminal.
Select this option when you control the projector via the LAN terminal during power standby.
Select this option when you don’t control the projector via the LAN terminal during power standby. This option disables the LAN terminal and reduces the power consumption during the power standby.
EN-27
Menu operation (continued)
INSTALLATION menu (continued)
ITEM
AUTO POWER ON
SETTING
OFF / ON
FUNCTION
When ON is chosen, the projector turns on automatically when the power cord is plugged in the wall outlet.
• When the lamp is off, the projector is in standby. Use the remote control to turn on the lamp.
AUTO POWER OFF
AV MUTE TIMER
IMAGE REVERSE
OFF / 5min-8hour
OFF / ON
OFF
MIRROR
INVERT
MIRROR INVERT
When no video signal is input and no operation is made, the projector automatically turns off after the selected time period. A dialog is displayed 5 minutes before the projector turns off.
When ON is chosen, AV MUTE is automatically canceled when the muting continues for one hour.
Select when viewing images projected from in front of the screen with the projector installed on the floor.
Select when viewing images projected from behind the screen with the projector installed on the floor.
Select when viewing images projected from behind the screen with the projector installed on the ceiling.
Select when viewing images projected from front of the screen with the projector installed on the ceiling.
Choose ON to automatically correct the distorted image.
The ADVANCED MENU is displayed for the following settings.
AUTO KEYSTONE
ADVANCED MENU
OFF / ON
ENTER
IMAGE CAPTURE
OK
SPLASH SCREEN ON / OFF
Use to capture the screen for the splash screen. (See page 62.)
BACK COLOR BLUE / BLACK /
IMAGE
Choose ON or OFF to display the splash screen when the power is turned on.
Use to select the background from among BLUE, BLACK and IMAGE, which will be displayed when there is no signal input from the source. When IMAGE is selected, the splash screen will be displayed.
Use to select the background when the AV MUTE button is pressed.
AV MUTE MODE BLACK / IMAGE
DIGITAL CABLE STANDARD
FINE ADJ.1/
FINE ADJ. 2
Select STANDARD for normal use.
Use to adjust the amount of transmission signal correction when a long cable is used.
• Regardless the setting of LAMP MODE in the INSTALLATION menu, the STANDARD lamp mode is activated by default whenever the projector is turned on. The LAMP MODE is set to either STANDARD or LOW depending on the setting last selected, and you cannot switch the LAMP MODE in about one minute after the lamp is on.
• Furthermore, you cannot switch LAMP MODE LOW1 to LOW2 in about three minutes after the lamp is on.
• When the STANDBY MODE is set to STANDARD, the audio is inputted from AUDIO IN terminal output during standby mode.
However, no audio is output when the last selected input was HDMI1, HDMI2 or LAN DISPLAY.
• The AUTO POWER OFF function does not work during AV MUTE.
• When STANDBY MODE is set to STANDARD, the fans rotate at very low speed during standby after plugging the power cord
(with 5 second high speed rotation at the beginning) and after turning off the lamp. This is to cool down the projector operating various functions during standby and is not a malfunction. When STANDBY MODE is set to LOW or LAN, the fans stop during standby.
EN-28
Menu operation (continued)
FEATURE menu
ITEM
ASPECT
SETTING
NORMAL
16:9
FULL
FUNCTION
Input video signal is displayed at the max height or max width of the panel while its aspect ratio is maintained.
Regardless of the type of input signal, image is displayed at 16:9 aspect ratio. Select to expand squeezed (or horizontally compressed) images such as DVD images to 16:9. Press the ENTER button to select whether or
not to display signals at 16:9 depending on their type. (See page 11.)
For TX20U only:
Press the ENTER button to select the image display position with the screen from CENTER, UPPER, and LOWER.
Select to project images in full size irrespective of type of input signal.
Use to enable or cancel the password lock. See page 62 for details.
PASSWORD
FUNCTION
DISPLAY INPUT /
MENU ACCESS /
SPLASH ID SCREEN
MENU POSITION 1 (upper left) / 2 (center)/
3 (lower right)
CINEMA MODE AUTO
Use to change the position of the menu.
VIDEO SIGNAL
OFF
AUTO / NTSC / PAL / SECAM /
4.43NTSC / PAL-M / PAL-N /
PAL-60
SIGNAL DETECT NORMAL (WXGA)
NORMAL (XGA)
ENHANCED
SETUP
LANGUAGE
RESET ALL
The film mode will be automatically activated when a film source signal is input. (Select AUTO for normal use.)
The film mode will not be activated.
When AUTO is selected, the appropriate video format is automatically selected depending on the input signal. If the image isn’t displayed correctly, select the desired video format manually.
Select this setting for wide picture.
Select this setting for other than wide picture.
Select this setting when the NORMAL mode does not display images properly. Select this for 1280 x 768 signals from COMPUTER/
COMPONENT VIDEO IN terminals.
AUTO
OFF
3.75% / 7.5%
Japanese / English / Spanish /
Germany / French / Italian /
Chinese / Korean / Russian /
Portuguese / Swedish / Polish /
Hungarian / Dutch / Norwegian /
Arabic / Turkish / Thai /
Indonesian / Malay / Vietnamese /
Finnish / Czech / Romanian
Select to change the SETUP mode automatically.
Select to make black lighter.
Select to make black thicker.
When 7.5% is chosen, the brightness is decreased by the set-up cancel function for the U.S. Choose OFF when the image is dark.
Use to select the language used in the menus.
OK
The menu settings are reset to the factory defaults (except the
LANGUAGE, PASSWORD FUNCTION and NETWORK settings).
• CINEMA MODE can be adjusted only when a TV60, TV50, 480i or 576i signal is being displayed.
• The RESET ALL process may take some time to complete.
EN-29
Menu operation (continued)
SIGNAL menu
ITEM
MEMORY CALL
SETTING
AUTO / MEMORY 1 -
MEMORY 8
RESOLUTION
(MEMORIZE)
VERTICAL
FREQUENCY
HORIZONTAL
FREQUENCY
-
-
HORIZ. PIXELS 640-1920
VERT. LINES 360-1200
EXECUTE
CANCEL
OK
HORIZ. POSITION 0-999
VERT. POSITION 0-999
FINE SYNC.
TRACKING
0-31
0-2800
COMPUTER INPUT AUTO
RGB
YC
B
C
R
/YP
B
P
R
OVER SCAN
HOLD
OK
100%-90%
OFF / ON
FUNCTION
Use to select the setting of RESOLUTION (MEMORIZE) already saved.
Impossible to select if no setting has been saved. AUTO is selected by default. It optimizes the signal format automatically depending on the type of video signal supplied from the computer. Press the ENTER button to clear the setting already saved.
The current resolution is displayed. To change the current setting, press the
ENTER button to display the RESOLUTION (MEMORIZE) menu. The new setting can be saved to MEMORY 1 - MEMORY 8.
The vertical frequency of the currently projected video signal is displayed.
The horizontal frequency of the currently projected video signal is displayed.
The number of horizontal pixels of the currently projected video signal is displayed. When you change the current setting, select EXECUTE, and then press the ENTER button, the image is automatically adjusted according to the resolution you set. The adjustment result can be saved to MEMORY 1 -
MEMORY 8.
The number of vertical lines of the currently projected video signal is displayed. When you change the current setting, select EXECUTE, and then press the ENTER button, the image is automatically adjusted according to the resolution you set. The adjustment result can be saved to MEMORY 1 -
MEMORY 8.
Press the ENTER button to start the automatic adjustment. At the completion of the automatic adjustment, a message is displayed and you can save the adjustment result to MEMORY 1 - MEMORY 8.
The process to change the current resolution is canceled and the SIGNAL menu is displayed.
Use to adjust the horizontal position of the projected image.
Use to adjust the vertical position of the projected image.
Use to eliminate flickering or blur, if appears, viewing the projected image.
Use to eliminate vertical wide stripes, if appears, viewing the projected image.
The proper setting is automatically selected.
Select this option when connecting the projector to high definition video equipment having R, G, and B output terminals.
Select this option when connecting the projector to a DVD player or other device having Y, C
B
, and C
R
(or Y, P
B
, and P
R
) component video output terminals.
Use to adjust the display area of projected image.
Use to adjust the image when flagging occurs near the top of the screen.
EN-30
Menu operation (continued)
SIGNAL menu (continued)
ITEM
USER
VERT. SYNC.
SETTING
ENTER
CLAMP POSITION 1-255
CLAMP WIDTH 1-63
AUTO / OFF
FUNCTION
The USER menu is displayed for the following adjustments.
Use to correct solid white or solid black in the projected image.
Use to correct solid black in the projected image.
Use to adjust the image when its motion doesn’t run smoothly. Select AUTO for normal use.
LPF
SHUTTER(U)
SHUTTER(L)
SHUTTER(LS)
ON / OFF
0-20
0-20
0-20
Use to select whether or not to enable the LPF. (See page 39.)
Use to adjust the image when noise appears on the top part of the image.
Use to adjust the image when noise appears on the bottom part of the image.
Use to adjust the image when noise appears on the left half of the image.
SHUTTER(RS) 0-20 Use to adjust the image when noise appears on the right half of the image.
• Though horizontal strips may appear on the enlarged projected image, such symptom is not a malfunction.
• When you change the horizontal or vertical position to a large extent, noise may appear.
• The adjustable range of the vertical position varies depending on the type of the input signal. Though the image may stay in the same position even when the setting value is changed, such symptom is not a malfunction.
• SHUTTER will not work correctly during keystone adjustment.
• When you increase the setting value of OVER SCAN, noise may appear on the screen.
• Menus may not be displayed partially depending on the settings of HORIZ. PIXELS and VERT. LINES in the RESOLUTION
(MEMORIZE) menu. In this case, execute AUTO POSITION. (See page 21.)
Important:
• You can set the IMAGE menu and the SIGNAL menu only when the signal is supplied.
• When the 3D in the IMAGE menu is set to ON, you cannot set OVER SCAN and SHUTTER.
EN-31
Menu operation (continued)
NETWORK menu
ITEM SETTING
PROJECTOR NAME *****...
NETWORK
CERTIFICATION
NETWORK
PASSWORD
IP CONFIG
ON / OFF
ENTER
OFF
***.***.***.***
FUNCTION
Set the name to identify the projector. Enter up to 15 characters (alphabets
or numeric characters). (See page 40.)
Select whether to enable the network certification or not. Select ON for
Set the password for the certification of PJLink™, ProjectorView Global+
and remote control via LAN. (See page 40.)
Select this setting for IP configuration. (See page 43.)
DHCP
IP ADDRESS
SUBNET MASK
ENTER
ON
***.***.***.***
DEFAULT
GATEWAY
***.***.***.***
MAC ADDRESS xx-xx-xx-xx-xx-xx
ON / OFF DHCP
FUNCTION
START IP
ADDRESS
END IP
ADDRESS
***.***.***.***
***.***.***.***
Select this setting when you obtain IP CONFIG automatically by DHCP server.
Select this setting when you set IP CONFIG manually.
Press the ENTER button to set IP ADDRESS. When DHCP is set to ON, you cannot change this setting
Press the ENTER button to set SUBNET MASK. When DHCP is set to ON, you cannot change this setting.
Press the ENTER button to set DEFAULT GATEWAY. When DHCP is set to
ON, you cannot change this setting.
Displays MAC ADDRESS.
Use this setting when using the projector as a DHCP server.
Press the ENTER button to set START IP ADDRESS. When DHCP is set to
ON or DHCP FUNCTION is set to OFF, you cannot change this setting.
Press the ENTER button to set END IP ADDRESS. When DHCP is set to ON or DHCP FUNCTION is set to OFF, you cannot change this setting.
SAVE SETTINGS OK Saves the IP CONFIG settings. When the IP CONFIG is not changed, you cannot select SAVE SETTINGS.
Select this setting for wireless configuration. (See page 45.)
WIRELESS
SETTING
SSID
ENTER
CHANNEL
********...
Set SSID. Enter up to 32 character alphabets (capital/small), numeric characters, or marks.
AUTO / 1 / 2 / 3 / 4 / 5 / 6 / 7 /
8 / 9 / 10 / 11
Select the wireless channel.
Select the wireless encrypted communication.
ENCRYPTION
WEP 128bit(ASCII) /
WEP 64bit(ASCII) /
WEP 128bit(HEX) /
WEP 64bit(HEX) /
WPA-PSK(ASCII) /
WPA2-PSK(ASCII) /
WPA-PSK(HEX) /
WPA2-PSK(HEX)
SAVE SETTINGS OK Saves the WIRELESS SETTING settings. When the WIRELESS SETTING is not changed, you cannot select SAVE SETTINGS.
EN-32
Menu operation (continued)
AMX DEVICE
DISCOVERY
OFF
NETWORK RESET
OK
/ ON
NETWORK
RESTART
OK
Use this setting when using an AMX controller.
Resets the network setting. (See page 45.)
Press the ENTER button to restart the network function.
EN-33
Menu operation (continued)
INFORMATION menu
ITEM
LAMP TIME (LOW)
INPUT
RESOLUTION
VERTICAL FREQUENCY
HORIZONTAL FREQUENCY
HORIZ. POSITION
VERT. POSITION
TRACKING
SYNC. TYPE
DESCRIPTION
This item shows the lamp operation time calculated based on that the LAMP MODE is LOW.
• When the LAMP MODE is STANDARD, this item shows a longer lamp operating time than the actual time.
• When the lamp operating time is 0 to 10 hours, “0H” is displayed. The lamp operating time exceeding 10 hours is indicated by the actual hours.
• When the lamp operating time reaches 4500hours, the bar turns to yellow. When it reaches
5700 hours, the bar turns to red.
• LAMP MODE "LOW" is included "LOW1" and "LOW2".
Indicates the name of the terminal to which the currently projected video signal is being input.
Indicates the resolution of the currently projected video signal.
Indicates the vertical frequency of the currently projected video signal.
Indicates the horizontal frequency of the currently projected video signal.
Indicates the HORIZ. POSITION adjustment value for the currently projected video signal.
Indicates the VERT. POSITION adjustment value for the currently projected video signal.
Indicates the TRACKING adjustment value for the currently projected video signal.
Indicates the type of the sync signal for the currently projected video signal.
• You can display the INFORMATION menu also by pressing the INFO. button on the remote control.
EN-34
Image adjustment
To adjust the brightness (CONTRAST and BRIGHTNESS):
You can make adjustments for the brightness of the projected image using the menu.
(See page 25 for menu setting.)
1. Display the IMAGE menu.
2. Select CONTRAST or BRIGHTNESS by pressing the
S or T button.
3. Adjust the selected item by pressing the
W or X button.
To cancel the menu:
4. Press the MENU button.
CONTRAST
Select to adjust the contrast of the image. Every time the
X button is pressed, the image becomes brighter and more clearly defined. Every time the
W button is pressed, the image becomes darker and less clearly defined.
BRIGHTNESS
Every time the
X button is pressed, the image becomes brighter. Every time the W button is pressed, the image becomes darker.
To adjust the color (COLOR and TINT):
You can adjust the color of the projected image using the menu.
(See page 25 for menu setting.)
1. Display the IMAGE menu.
2. Select COLOR or TINT by pressing the
S or T button.
• COLOR or TINT is unavailable when COMPUTER1, COMPUTER2, HDMI1, HDMI2, LAN DISPLAY, USB DISPALY or USB VIEWER is selected as the input source.
• TINT is available only when the NTSC signal is input.
3. Adjust the selected item by pressing the
W or X button.
To cancel the menu:
4. Press the MENU button.
COLOR
Use to adjust the color density of the projected image. Every time the
X button is pressed, the color becomes darker.
Every time the
W button is pressed, the color becomes lighter.
TINT
Use to adjust the tint of the projected image. Every time the
X button is pressed, the image appears more greenish.
Every time the
W button is pressed, the image appears more reddish.
To sharpen or soften the projected image (SHARPNESS):
You can adjust the sharpness of the projected image using the menu.
(See page 25 for menu setting.)
1. Display the IMAGE menu.
2. Select SHARPNESS by pressing the
S or T button.
3. Adjust the selected item by pressing the
W or X button.
To cancel the menu:
4. Press the MENU button.
EN-35
Image adjustment (continued)
To adjust the tone of white (COLOR TEMP.):
You can select a preset color temperature (white tone) using the menu.
(See page 25 for menu setting.)
1. Display the IMAGE menu.
2. Select COLOR TEMP. by pressing the
S or T button.
3. Select your desired color temperature by pressing the
W or X button.
To cancel the menu:
4. Press the MENU button.
To adjust the tone of white (To customize the color temperature):
To customize (and store) the color temperature to your preference, carry out the following procedure.
(See page 25 for menu setting.)
1. Select COLOR TEMP. in the IMAGE menu.
2. Press the
W or X button to select USER .
3. Press the ENTER button.
4. Press the
S or T button to select the desired item.
5. Press the
W or X button to adjust the selected item.
6. Repeat steps 4 and 5 for optimum adjustment results.
To cancel the menu:
7. Press the MENU button.
To enable the stored color temperature:
1. Set COLOR TEMP. to USER in the IMAGE menu.
About color temperature
There are different variations in white color. Color temperature is a way to show these variations in white. When the temperature is low, white appears reddish. When the temperature rises, white appears bluish. For example, you can change the temperature using the following procedures.
To raise the color temperature: Increase the CONTRAST B (blue) and decrease the CONTRAST R (red).
To reduce the color temperature: Decrease the CONTRAST B (blue) and increase the CONTRAST R (red).
• If you set all of CONTRAST R, G, and B to negative values, the original brightness of the image can’t be obtained even when you maximize CONTRAST in the IMAGE menu.
COLOR ENHANCER
You can set the user-defined balance between the brightness and hue using the menu.
(See page 25 for menu setting.)
1. Display the IMAGE menu.
2. Select COLOR ENHANCER by pressing the
S or T button.
3. Select USER by pressing the
W or X button.
4. Press the ENTER button.
• The detailed menu for the color enhancer is displayed.
5. Press the
S or T button to select BrilliantColor™ or GAMMA MODE.
6. Press the
W or X button to adjust the selected item.
When USER is selected:
EN-36
Image adjustment (continued)
BrilliantColor™
Use this setting to make colors with medium brightness, such as yellow and the skin tone appear natural. Press the
W button to decrease the value to lessen the effect. Press the
X button to increase the value to heighten the effect.
(BrilliantColor™ has no effect at value 0.)
• For more enhanced color reproduction, set BrilliantColor™ to 0. The white area of the color wheel is disabled, and you can reproduce true-color images.
GAMMA MODE
Use this item to set the gamma optimally.
DYNAMIC ................
Select when viewing images supplied from the computer.
NATURAL ................
Select when viewing images supplied from the video device.
DETAIL.....................
Select when viewing images of which brightness should be kept relatively low, such as movies and music performance.
Important
• You can adjust COLOR ENHANCER also by pressing the COLOR.E button on the remote control.
With the remote control:
1. Press the COLOR.E button on the remote control.
A window for color enhancer adjustment appears on the upper right of the screen.
2. Press the
W or X button to select USER .
3. Press the ENTER button.
4. Press the
S or T button to select BrilliantColor™ or GAMMA MODE.
5. Press the
W or X button to adjust the selected item.
Adjusting the tone of each color (COLOR MANAGEMENT):
You can individually adjust the tone of red, green, blue, cyan, yellow, magenta and white using the menu.
1. Display the IMAGE menu.
2. Press the
S or T button to select COLOR MANAGEMENT.
3. Press the ENTER button.
4. Press the
W or X button to select a color to be adjusted: RED, GREEN, BLUE,
CYAN, YELLOW, or MAGENTA .
5. Press the
S or T button to select an item to be adjusted: GAIN, SATURATION or HUE.
6. Press the
W or X button to adjust the item.
To cancel the menu:
7. Press the MENU button.
EN-37
Image adjustment (continued)
How to adjust the computer image
This projector automatically selects a proper signal format according to the type of video signal supplied from the computer. However, video signals from the computer may not be projected correctly depending on the types of the computer and images to be projected. In such a case, make adjustment according to the flowchart below.
When the size and position of the computer image are not correct.
Project a bright computer image containing as many texts and characters as possible.
Note) Disable the screen saver if it is active.
Change the setting of SIGNAL DETECT in the FEATURE menu.
Press the AUTO POSITION button.
Settings are automatically and optimally adjusted for the input signal.
Press the AUTO POSITION button.
Settings are automatically and optimally adjusted for the input signal.
Image is projected correctly.
YES
NO
Image is projected correctly.
YES
NO
Display the screen resolution setting menu of your computer.
(Example: In the case of Windows
®
PC, right-click on the desktop, select Properties, and click the
Settings tab to display the screen resolution setting.)
The screen resolution setting of your computer is different from the setting of RESOLUTION
(MEMORIZE ) in the SIGNAL menu of the projector.
NO
YES
Select RESOLUTION (MEMORIZE ) in the SIGNAL menu and press the ENTER button.
Set HORIZ. PIXELS and VERT. LINES to the values of the screen resolution of your computer.
(Example: When the screen resolution of the computer is 1280x800, set HORIZ. PIXELS to 1280 and
VERT. LINES to 800.)
Select EXECUTE and press the ENTER button.
Automatic adjustment starts according to the selected resolution.
Image is projected correctly.
YES
After the memory saving message is displayed, select your desired memory number and press the
ENTER button.
NO
Perform manual adjustment.
YES
After the memory saving message is displayed, select your desired memory number and press the
ENTER button.
NO
When you don’t save the adjustment result, press the MENU button.
Adjustment is canceled.
Adjust HORIZ. POSITION, VERT. POSITION, and TRACKING in the SIGNAL menu. For details, see “Simple method to adjust the image position.” (See page 38.)
Adjustment is completed.
EN-38
Image adjustment (continued)
How to adjust the image supplied from the computer using the menu:
Carry out the following procedures according to the symptoms.
Wide strips appear ...........................................................
Adjust TRACKING in the SIGNAL menu.
The projected image flickers.
The projected image is blurred.........................................
Adjust FINE SYNC. in the SIGNAL menu.
The projected image is displaced horizontally .................
Adjust HORIZ. POSITION in the SIGNAL menu. Every time the
W button is pressed, the image moves to the right. Every time the
X button is pressed, the image moves to the left.
The projected image is displaced vertically .....................
Adjust VERT. POSITION in the SIGNAL menu. Every time the
W button is pressed, the image moves down.
Every time the
X button is pressed, the image moves up.
The top part of the image flags ........................................
Change the setting of HOLD in the SIGNAL menu.
Select ON , press the ENTER button, and adjust
BEGIN or END to minimize the flagging.
A solid black or solid white appears in the image ............
Adjust CLAMP POSITION or CLAMP WIDTH in the
SIGNAL - USER menu
The motion doesn’t run smoothly ....................................
Adjust VERT. SYNC. in the SIGNAL - USER menu.
Select AUTO for normal use.
Noise appears on the right or left half of the image .........
Adjust SHUTTER(LS) or SHUTTER(RS) in the SIGNAL -
USER menu.
Noise appears on the top or bottom part of the image....
Adjust SHUTTER(U) or SHUTTER(L) in the SIGNAL -
USER menu.
1. Display the SIGNAL menu.
2. Press the
S or T button to select a setting to adjust.
3. Adjust the selected setting by pressing the
W or X button.
To cancel the menu:
4. Press the MENU button.
• Do not change the settings of the SIGNAL menu for ordinary use.
Simple method to adjust the image position
To adjust the horizontal position:
1. Align the left edge of the image with the left side of the screen by adjusting HORIZ. POSITION. Then, align the right edge of the image with the right side of the screen by adjusting TRACKING.
2. Repeat step 1 above to complete the adjustment of the horizontal position.
To adjust the vertical position:
3. Align the upper edge of the image with the upper side of the screen by adjusting VERT. POSITION.
LPF (Progressive filter)
You can select whether or not to enable the LPF. Vertical or horizontal streak noise may appear on the projected image, depending on the type of the DVD player or game console you use. In such a case, you can reduce such streak noise by enabling the LPF. However, projected images become softened slightly.
EN-39
Network settings
You can set the network of the projector using the menu.
Setting Projector Name
(See page 25 for menu setting.)
1. Display the NETWORK menu
2. Press the
S or T button to select PROJECTOR
NAME.
3. Press the ENTER button.
• The PROJECTOR NAME screen appears.
CLEAR key: ..... Deleting all the entered characters.
5. When selecting OK, the setting is completed as the name stored. However, when selecting CANCEL, the setting is completed without storing.
• The display returns the NETWORK menu after selecting OK or CANCEL.
• It may take some time to reflect the settings.
Enabling or disabling the network certification
You can select whether or not to certify the network communication using the network password.
• For details, contact your dealer.
(See page 25 for menu setting.)
1. Display the NETWORK menu.
2. Press the
S or T button to select NETWORK
CERTIFICATION.
3. Press the ENTER button.
• NETWORK CERTIFICATION dialog appears.
4. Press the direction buttons to move the key cursor, select the characters or marks to enter, and press the ENTER button.
• Projector Name can be set using up to 15 characters including alphabets (capital/small), numeric characters, or marks.
key:.............. Shifting the position of enter cursor to the left for each character.
key:.............. Shifting the position of enter cursor to the right for each character.
DEL key: .......... Deleting the character in the position of enter cursor for each character.
caps/CAPS key: Switching an alphabet character to CAPITAL or small.
NEXT/PREV key: Switching the marks listed on the fourth line.
SPACE key: ..... Inserting a space in the position of enter cursor.
4. Press the
W or X button to select ON or OFF .
5. Select the item to set, and press the ENTER button.
• To cancel the setting, press the MENU button.
• It may take some time to reflect the setting.
Network Password Settings
(See page 25 for menu setting.)
1. Display the NETWORK menu.
2. Press the
S or T button to select NETWORK
PASSWORD.
3. Press the ENTER button.
• CURRENT NETWORK PASSWORD screen appears.
4. Press the direction buttons to move the key cursor, select the characters or marks to enter, and press the ENTER button.
EN-40
Network settings (continued)
• Password can be set using up to 32 characters including alphabets (capital/small) or numeric characters.
key:.............. Shifting the position of enter cursor to the left for each character.
key:.............. Shifting the position of enter cursor to the right for each character.
DEL key: .......... Deleting the character in the position of enter cursor for each character.
caps/CAPS key: Switching an alphabet character to CAPITAL or small.
NEXT/PREV key: Switching the marks listed on the fourth line.
CLEAR key: ..... Deleting all the entered characters.
• The default password is “admin”.
5. Select OK, and NEW NETWORK PASSWORD screen appears if the entered password is correct.
• If the entered password is not correct, the
CURRENT NETWORK PASSWORD screen appears again.
CLEAR key: ..... Deleting all the entered characters.
7. When NEW NETWORK PASSWORD and CONFIRM
NETWORK PASSWORD are matched, the setting is completed after changing the NETWORK
PASSWORD.
• When you select CANCEL, the NETWORK menu is displayed without changing the password.
• If the entered content is not matched, NEW
NETWORK PASSWORD screen appears again after an error dialog is displayed.
• It may take some time to reflect the settings.
IP Settings
(See page 25 for menu setting.)
1. Display the NETWORK menu.
2. Press the
S or T button to select IP CONFIG.
3. Press the ENTER button.
• IP CONFIG menu appears.
6. Enter the NEW NETWORK PASSWORD and
CONFIRM NETWORK PASSWORD.
• Password can be set using up to 32 characters including alphabets (capital/small) or numeric characters.
key: ............. Shifting the position of enter cursor to the left for each character.
key: ............. Shifting the position of enter cursor to the right for each character.
key:.............. Shifting the position of enter cursor between NEW NETWORK
PASSWORD and CONFIRM
NETWORK PASSWORD.
DEL key: .......... Deleting the character in the position of enter cursor for each character.
caps/CAPS key: Switching an alphabet character to CAPITAL or small.
Setting or Clearing DHCP
1. Display the IP CONFIG menu.
2. Press the
S or T button to select DHCP.
3. Press the
W or X button to select ON or OFF.
• When setting DHCP to ON, IP ADDRESS,
SUBNET MASK, DEFAULT GATEWAY, and DHCP
FUNCTION cannot be set. If you set those settings, set DHCP to OFF and perform the IP settings as the following procedures.
• Until the execution of SAVE SETTINGS, the change is not saved.
EN-41
Network settings (continued)
IP Address Settings
1. Display the IP CONFIG menu.
2. Press the
S or T button to select IP ADDRESS.
3. Press the ENTER button.
• IP ADDRESS screen appears.
• Refer to IP Address Settings for the detail of entering.
5. When selecting OK, the setting is completed as the
Subnet Mask stored temporarily. However, when selecting CANCEL, the setting is completed without storing.
• When the setting you entered is correct, the IP
CONFIG menu is displayed. If the entered content is not correct, the IP CONFIG menu is displayed after an error dialog is displayed.
• Until the execution of SAVE SETTINGS, the change is not saved.
4. Press the direction buttons to move the key cursor, select the numbers to enter, and press the ENTER button.
• Set the numeric value within the range from 0 to
255. However, set the numeric value for the final octet within the range from 1 to 254.
key: ............. Shifting the position of enter cursor to the left.
key:.............. Shifting the position of enter cursor to the right.
DEL key: .......... Deleting the character in the position of enter cursor for each character
CLEAR key: ..... Deleting all the entered characters.
5. When selecting OK, the setting is completed as the
IP ADDRESS stored temporarily. However, when selecting CANCEL, the setting is completed without storing.
• When the setting you entered is correct, the IP
CONFIG menu is displayed. If the entered content is not correct, the IP CONFIG menu is displayed after an error dialog is displayed.
• Until the execution of SAVE SETTINGS, the change is not saved.
Default Gateway Settings
1. Display the IP CONFIG menu.
2. Press the
S or T button to select DEFAULT
GATEWAY.
3. Press the ENTER button.
• DEFAULT GATEWAY screen appears.
4. Enter the Default Gateway.
• Refer to IP Address Settings for the detail of entering.
5. When selecting OK, the setting is completed as the
Default Gateway stored temporarily. However, when selecting CANCEL, the setting is completed without storing.
• When the setting you entered is correct, the IP
CONFIG menu is displayed. If the entered content is not correct, the IP CONFIG menu is displayed after an error dialog is displayed.
• Until the execution of SAVE SETTINGS, the change is not saved.
Subnet Mask Settings
1. Display the IP CONFIG menu.
2. Press the
S or T button to select SUBNET MASK.
Setting or clearing DHCP Function
1. Display the IP CONFIG menu.
2. Press the
S or T button to select DHCP
FUNCTION.
3. Press the ENTER button.
• SUBNET MASK screen appears.
4. Enter the Subnet Mask.
3. Press the
W or X button select ON or OFF.
• When DHCP FUNCTION is set to OFF, START IP
ADDRESS and END IP ADDRESS cannot be set.
If you want to set these settings, set DHCP
FUNCTION to ON and perform the IP settings as follows.
EN-42
Network settings (continued)
Start IP Address setting
1. Display the IP CONFIG menu.
2. Press the
S or T button to select START IP
ADDRESS.
3. Press the ENTER button.
• START IP ADDRESS screen appears.
• Set the numeric value within the range from 0 to
255. However, set the numeric value for the final octet within the range from 3 to 254. Moreover, set the numeric value larger than START IP
ADDRESS in the same subnet class.
• When the setting you entered is correct, the IP
CONFIG menu is displayed. If the entered content is not correct, the IP CONFIG menu is displayed after an error dialog is displayed.
• Until the execution of SAVE SETTINGS, the change is not saved.
Saving IP CONFIG Settings
1. Display the IP CONFIG menu.
2. Press the
T button to select SAVE SETTINGS.
4. Enter the Start IP address.
• Refer to IP Address Settings for the detail of entering.
5. When selecting OK, the setting is completed as the
START IP ADDRESS stored temporarily. However, when selecting CANCEL, the setting is completed without storing.
• Set the numeric value within the range from 0 to
255. However, set the numeric value for the final octet within the range from 2 to 254. Moreover, set the numeric value larger than IP address in the same subnet class.
• When the setting you entered is correct, the IP
CONFIG menu is displayed. If the entered content is not correct, the IP CONFIG menu is displayed after an error dialog is displayed.
• Until the execution of SAVE SETTINGS, the change is not saved.
End IP Address setting
1. Display the IP CONFIG menu.
2. Press the
S or T button to select END IP
ADDRESS.
3. Press the ENTER button.
• The setting change dialog is displayed. After the dialog disappears, the NETWORK menu is displayed.
• It may take some time to reflect the settings.
Wireless Setting
(See page 32 for menu setting.)
1. Display the NETWORK menu.
2. Press the
S or T button to select WIRELESS
SETTING.
3. Press the ENTER button.
• The WIRELESS SETTING menu appears.
3. Press the ENTER button.
• END IP ADDRESS screen appears.
SSID setting
1. Display the WIRELESS SETTING menu.
2. Press the
S or T button to select SSID.
4. Enter the End IP address.
• Refer to IP Address Settings for the detail of entering.
5. When selecting OK, the setting is completed as the
END IP ADDRESS stored temporarily. However, when selecting CANCEL, the setting is completed without storing.
EN-43
Network settings (continued)
3. Press the ENTER button.
• The SSID screen appears.
• ENCRYPTION dialog appears.
4. Press the
S, T, W, and X buttons to move the key cursor to select the characters or marks to enter, and press the ENTER button.
• SSID can be set using up to 32 characters including alphabets (capital/small) or numeric characters.
key: ............. Shifting the position of enter cursor to the left for each character.
key: ............. Shifting the position of enter cursor to the right for each character.
DEL key: ......... Deleting the character in the position of enter cursor for each character.
caps/CAPS key: Switching an alphabet character to CAPITAL or small.
NEXT/PREV key: Switching the marks.
SPACE key: .... Inserting a space in the position of enter cursor.
CLEAR key: .... Deleting all the entered characters.
• The default SSID is “MITSUBISHI Projector”.
5. Select OK to complete the setting with the SSID stored. Select CANCEL to complete the setting without storing.
• The display returns to the WIRELESS SETTING menu after selecting CANCEL.
Channel setting
1. Display the WIRELESS SETTING menu.
2. Press the
S or T button to select CHANNEL.
3. Press the
W or X button to select AUTO or 1 to 11.
• To cancel the setting, press the MENU button.
Encryption setting
1. Display the WIRELESS SETTING menu.
2. Press the
S or T button to select ENCRYPTION.
3. Press the ENTER button.
4. Press the
W or X button to select OFF or the other encryption.
5. Press the ENTER button.
• The KEY screen appears.
• The keypad on the KEY screen varies depending on the selected Encryption setting.
• To cancel the setting, press the MENU button.
EN-44
6. Press the
S, T, W, and X buttons to move the key cursor to select the characters or marks to enter, and press the ENTER button.
• KEY can be set using up to 64 characters including alphabets (capital/small) or numeric characters.
key: ............ Shifting the position of enter cursor to the left for each character.
key: ............ Shifting the position of enter cursor to the right for each character.
DEL key: ......... Deleting the character in the position of enter cursor for each character.
caps/CAPS key: Switching an alphabet character to CAPITAL or small.
NEXT/PREV key: Switching the marks.
SPACE key: .... Inserting a space in the position of enter cursor.
CLEAR key: .... Deleting all the entered characters.
7. Select OK to complete the setting with the
ENCRYPTION and KEY stored. Select CANCEL to complete the setting without storing.
• The display returns to the WIRELESS SETTING menu after selecting CANCEL.
• The number of characters of KEY varies depending on the ENCRYPTION setting.
• WEP 128bit(ASCII): 13 chars
• WEP 64bit(ASCII): 5 chars
• WEP 128bit(HEX): 26 digits
• WEP 64bit(HEX): 10 digits
• WPA-PSK(ASCII): 8-63 chars
• WPA2-PSK(ASCII): 8-63 chars
Network settings (continued)
• WPA-PSK(HEX): 64 digits
• WPA2-PSK(HEX): 64 digits
• If the entered content is outside character number range, the KEY screen appears again after an error dialog is displayed.
Saving Wireless Settings
1. Display the WIRELESS SETTING menu.
2. Press the
S or T button to select SAVE SETTINGS.
Restart of network function
(See page 25 for menu setting.)
1. Display the NETWORK menu.
2. Press the
S or T button to select NETWORK
RESTART.
3. Press the ENTER button.
• Confirmation dialog appears.
4. If the ENTER button is pressed again, the
WIRELESS SETTING will be refl ected.
• It may take some time to refl ect the setting.
Enabling or disabling the AMX
Device Discovery
Select this setting when using the AMX controller.
(See page 25 for menu setting.)
1. Display the NETWORK menu.
2. Press the
S or T button to select AMX DEVICE
DISCOVERY.
3. Press the ENTER button.
• Network Restart dialog appears.
4. If the ENTER button is pressed again, the network function will be restarted.
• It may take some time to restart the function.
How to use network function
• When connecting a computer and projector with
LAN, configure the both IP Addresses in the same network group.
If connecting in different network group, be sure to use a router. As for the settings of a router, ask the network administrator.
• Configure the IP CONFIG correctly. If the settings are not correct, the communication may be unavailable. For the detail, consult the network administrator.
• Depending on the settings of STANDBY MODE of the projector, LAN function may be unavailable.
See page 27 for the detail of STANDBY MODE.
3. Press the ENTER button.
• AMX dialog appears.
4. Press the
W or X button to select ON or OFF .
5. Select the item to set, and press the ENTER button.
• To cancel the setting, press the MENU button.
• It may take some time to reflect the setting.
Initialization of network settings
(See page 25 for menu setting.)
1. Display the NETWORK menu.
2. Press the
S or T button to select NETWORK
RESET.
3. Press the ENTER button.
• Network Initialization dialog appears.
4. If the ENTER button is pressed again, the network settings will be initialized.
• It may take some time to initialize the settings.
Glossary
For more detail of the glossary below, refer to the technical book that is commercially available.
Term Description
DHCP
IP Address
Abbreviation for Dynamic Host
Configuration Protocol. This protocol automatically assigns IP
Address to networked devices.
Numerical address to identify networked computers.
Subnet Mask
Default
Gateway
MAC
Address
A numeric value to define the number of bits used for a network address of a divided network (or subnet) in an IP Address.
A server (or router) to communicate across networks (subnets) that are divided by Subnet Mask.
Abbreviation for Media Access
Control Address. MAC Address is a unique ID number assigned to each network adapter. And this is based on which data are sent and received between network adapters.
EN-45
Advanced display utilities
USB Display
You can project the computer images inputted via a
USB connection.
Supported OS’s are as follows:
• Windows XP
• Windows Vista
• Windows 7
• Mac OS X 10.5 or later
Important:
• You need to install the driver only when using MAC
OS X.
• Mac computers based on the PowerPC processors are not supported.
• Only 1-to-1 screen projection is supported.
• Moving images cannot be displayed.
Connection
Connect the projector and the computer using a commercially available USB cable.
You can set the network of the projector using the menu.
Installation of driver
When using Mac OS X, install the driver after connecting the projector and the computer using a USB cable for the first time. Once you have installed the driver, you don’t need to install it again.
Installing USB Display driver
1. Via the Finder, open [USB_DISPLAY] and doubleclick [USB Display.pkg].
2. Follow the on-screen instructions to install the driver.
When deleting USB Display driver (Uninstallation)
1. Via the Finder, open the [Applications] folder and double-click the [USB Display] folder.
Computer
USB 4-pin
(type B)
USB 4-pin
(type A)
To USB-B terminal
USB cable
(option)
To USB port
Important:
• The USB-B terminal on this projector is compatible with USB 2.0.
• Do not use a USB hub between the projector and the computer.
2. Double-click [UninstallVendorSpecificType05].
3. Follow the on-screen instructions to uninstall the driver.
EN-46
Advanced display utilities (continued)
Operation
Starting USB Display projection
1. Press the SOURCE button and select USB DISPLAY.
• When the USB Display input is selected, the splash screen for USB Display appears on the screen.
2. When the computer is connected to the projector, the computer image is automatically displayed on the screen.
Ending USB Display projection
When using Windows XP, Windows Vista, or
Windows 7
3. Unplug the USB cable from the projector.
• It is not necessary to “Safely Remove Hardware” on the computer or to press the UNPLUG button on the remote control.
When using Mac OS X
4. On the computer, open the Finder and click “ “ on the right of [USB_DISPLAY] to unmount the projector.
5. Unplug the USB cable from the projector.
Important:
• When the image is projected, the computer resolution will be changed according to the projector model and will be automatically recovered after unplugging the USB cable.
LAN Display
You can project the computer images inputted via a wired or wireless LAN.
You can also perform the following during the LAN
Display projection:
• 4-to-1 split screen projection
Images from up to 4 computers can be projected split on 1 projector screen.
• Remote desktop
Connecting an input device such as a mouse or keyboard to the USB-A terminal on the projector enables the following computer operations from the projector.
• Showing local files of the computer
• Operating the application software
• Showing server files on the network
• Browsing of the internet
• SidePad
Computer images are transferred to the tablet computer and you can operate the computer from the tablet computer.
To use the LAN Display function, you need to install the software “LAN Display System” contained in the attached CD-ROM.
Supported OS’s are as follows:
• Windows XP
• Windows Vista
• Windows 7
• Mac OS X 10.5 or later
Important:
• Mac computers based on the PowerPC processors are not supported.
• Remote desktop cannot be performed during 4-to-1 split screen projection.
Installation of software
Installing LAN Display System
Before starting installation, be sure to read
“ReadMe.txt” contained in the CD-ROM.
When using Windows XP, Windows Vista, or
Windows 7
1. Copy “LAN Display System_v300.exe” contained in the TOOLS folder of CD-ROM to the hard disk of your computer.
2. Double-click “LAN Display System_v300.exe” on the hard disk, and start up the installer of the LAN
Display System.
3. Follow the on-screen instructions to install the software.
• When the installation has been completed, LAN
Display System is automatically executed.
EN-47
Advanced display utilities (continued)
When using Mac OS X
1. Copy “LAN Display System_v300.dmg” contained in the TOOLS folder of CD-ROM to the hard disk of your computer.
2. Double-click “LAN Display System_v300.dmg” on the hard disk.
• The volume is mounted.
3. Drag and drop “LAN Display System” and
“SidePadLite” into the [Applications] folder.
Connection
Connect the projector and the computer either by using a commercially available LAN cable or USB wireless
LAN adapter.
Computer
LAN cable
(option)
To LAN terminal
When deleting LAN Display System (Uninstallation)
Important:
• When uninstalling LAN Display System, it should be ended in advance. If the application continues operating, uninstallation cannot be performed normally.
When using Windows XP, Windows Vista, or
Windows 7
1. Select [Start]-[All Programs]-[LAN Display System]-
[Uninstall].
2. Follow the on-screen instructions to uninstall the software.
When using Mac OS X
1. Open the [Applications] folder.
2. Drag and drop “LAN Display System” and
“SidePadLite” to the trash.
Computer
To USB-A terminal
USB wireless
LAN adapter
(option)
Important:
• For wired LAN connection, use a category-5 LAN cable. Both straight-through and crossover cables can be used.
• The USB-A terminal on this projector is compatible with USB 2.0.
• When using a USB hub, you are recommended to use the one with external power supply.
• Some USB hubs cannot be used depending on the specifications.
• Some USB wireless LAN adapters cannot be used depending on the specifications.
• IP address, subnet mask, default gateway values are the same for both wired LAN and wireless LAN.
• Data are not filtered between wired LAN and wireless LAN interface.
Projection
Selecting a LAN Display input
1. Press the SOURCE button and select LAN DISPLAY.
• When the LAN Display input is selected, the splash screen for LAN Display appears on the screen.
EN-48
Advanced display utilities (continued)
Starting the LAN Display System
2. Click the LAN Display System icon “ “ to execute the program.
• The program starts to search for projectors automatically.
• During searching for projectors, Searching icon is displayed.
• When a projector is found, the computer logs in to the projector automatically and the computer image is projected. The main user interface appears on the computer screen.
• When multiple projectors are found, the following window appears on the computer screen.
• Stop button:
Stops the projection.
• Freeze button:
Freezes the projected image.
• Menu button:
Displays the menu window. (See the next step for details.)
• Exit button:
Exits the LAN Display System.
4. Click the Menu button on the main user interface to display the menu window and select functions.
Menu window
Select a projector and click [OK]. The computer logs in to the projector and the computer image is projected.
Important:
• If the computer resolution is higher than 1280 x 800, a confirmation dialog for changing the computer resolution is displayed. When [OK] is selected, the computer resolution will be changed according to the projected image. When [Cancel] is selected, the computer resolution will not be changed and the projected image size will be smaller than the screen size. The computer resolution will be automatically recovered after the LAN Display System is ended.
Operating the LAN Display System
3. Click the buttons on the main user interface to operate the projection.
Freeze button
Stop button
Play button
Menu button
Exit button
• Search Server
Searches for the projectors on the network. If this function is selected, the LAN Display projection will quit automatically.
• Projection Source*
Chooses the computer screen to be projected, main screen or virtual extended screen which is activated by computer’s virtual display function.
Main screen Virtual extended screen
Split 1 button
Split 3 button
Split 2 button
Split 4 button
• Play button:
Projects the image in full screen.
• Split 1-4 buttons:
Click either of the buttons to project the image on relevant split screen.
EN-49
Important:
• To project a virtual extended screen, the attached Virtual display driver must be installed.
• Hide UI*
Hides or displays the main user interface on the projected image.
• Launch SidePad (or Stop SidePad) -> MirrorOp
Receiver
Launches (or stops) SidePad.
• Advanced Screen Capture*
Enables or disables balloon tips and pop-up windows.
• Send Audio to Display
Enables or disables the transfer of computer sound.
Advanced display utilities (continued)
Important:
• To use this function with Windows XP, the attached Virtual Audio driver must be installed.
• To use this function with Mac OS X, attached
Soundflower must be installed.
• About
Displays the version information of the LAN
Display System.
• Exit
Exits the LAN Display System.
Important:
• The items marked with “*” are not available for
Mac OS X.
• When “Advanced Screen Capture” is enabled, the computer mouse cursor may blink.
Ending the LAN Display projection
5. Click the Exit button on the main user interface or the menu window to exit the LAN Display System.
6. In case of the wireless LAN communication, unplug the USB wireless LAN adapter from the projector.
Before unplugging, be sure to press the UNPLUG button on the remote control and select [Yes] on the screen by pressing the
W or X button and then
ENTER button.
Important:
• Do not switch the input source to USB DISPLAY or
USB VIEWER during the wireless LAN communication. If switched, the communication will be disconnected.
• During wireless LAN communication, the projector cannot communicate with the access point.
• Only infrastructure mode is available to wireless LAN communication. Adhoc mode is not available.
Installing the virtual display driver
To project a virtual extended screen, install the Virtual display driver as follows.
1. Double-click “Virtual display driver.exe” contained in
“C:\Program Files\LAN Display System”, and start up the installer of the Virtual display driver.
2. The Setup window is displayed. Click [Next] and operate according to the instructions on the window.
Installing the Virtual Audio driver
To use “Send Audio to Display” with Windows XP, install the Virtual display driver as follows. Before starting installation, be sure to read “ReadMe.txt” contained in the CD-ROM.
1. Copy “Virtual Audio driver.exe” contained in the
TOOLS folder of CD-ROM to the hard disk of your computer.
2. Double-click “Virtual Audio driver.exe” on the hard disk, and start up the installer of the Virtual Audio driver.
3. Follow the on-screen instructions to install the software.
Installing Soundflower
To use “Send Audio to Display” with Mac OS X, install
Soundflower as follows.
1. Copy “Soundflower.pkg” contained in the TOOLS folder of CD-ROM to the hard disk of your computer.
2. Double-click “Soundflower.pkg” on the hard disk, and start up the installer of Soundflower.
3. Follow the on-screen instructions to install the software.
Using remote desktop
4. Connect an USB device such as a mouse or keyboard to the USB-A terminal on the projector.
While the computer images are projected with the
LAN Display, the computer can be operated with the device.
To USB-A terminal
3. When the installation has been completed, restart the computer.
Important:
• The USB-A terminal on this projector is compatible with USB 2.0.
• Supported USB device is standard USB HID device with power consumption less than 5V/500mA.
• When using a keyboard and mouse together, we recommend a commercially available wireless keyboard and wireless mouse intended for a computer with wireless receiver.
• When using a USB hub, you are recommended to use the one with external power supply.
• Some USB hubs cannot be used depending on the specifications.
EN-50
Advanced display utilities (continued)
Using SidePad function
While computer images are projected with the LAN
Display, you can operate the computer from the tablet computer.
To use the SidePad function, you need to install the free software “MirrorOp Receiver” to the tablet computer.
Supported OS°¶s of MirrorOp Receiver are as follows:
• iOS 3.2 or later
• Android 2.1 or later
Installation of software
1. Download the MirrorOp Receiver from the Internet to the tablet computer.
• Connect to Apple Store to download the software for iOS.
• Connect to Google Play to download the software for Android.
• The communication fee to connect to Apple Store or Google Play will be borne by the customer.
Connection
Connect the projector, computer and tablet computer to the same network using a commercially available
USB wireless LAN adapter, etc.
Tablet computer
To USB-A terminal
USB wireless
LAN adapter
(option)
Computer
2. On the computer, click the Menu button on the main user interface to display the menu window and select [Launch SidePad -> MirrorOp Receiver].
• Computer images are transferred to the tablet computer and you can operate the computer from the tablet computer.
Important:
• If more than one tablet computer running MirrorOp
Receiver exist in the same network, the device selection screen appears. Select the tablet computer where to transfer the computer images.
Ending SidePad
3. On the computer, click the Menu button on the main user interface to display the menu window and select [Stop SidePad -> MirrorOp Receiver].
• Pressing the Home button on the tablet computer also turns off the SidePad.
Important:
• Some USB wireless LAN adapters cannot be used depending on the specifications.
Starting SidePad
1. On the tablet computer, tap the MirrorOp Receiver icon “ “ to turn on MirrorOp Receiver.
• The MirrorOp Receiver startup screen is displayed.
EN-51
Advanced display utilities (continued)
WiFi-Doc
Via a wireless LAN, you can transfer the images of the
Microsoft PowerPoint, Word, Excel, PDF, TXT, or JPEG format stored in the tablet computer or screen shot to the projector and project them controlling with the tablet computer.
To use WiFi-Doc, you need to install the free software
“WiFi-Doc (Bundle Version)” to the tablet computer.
Supported OS’s of WiFi-Doc (Bundle Version) are as follows:
• iOS 4.2 or later
• Android 2.1 or later
Installation of software
1. Download the WiFi-Doc (Bundle Version) from the
Internet to the tablet computer.
• Connect to Apple Store to download the software for iOS.
• Connect to Google Play to download the software for Android.
• The communication fee to connect to Apple Store or Google Play will be borne by the customer.
Connection
Connect the projector and the tablet computer using a commercially available USB wireless LAN adapter.
2. Turn on Wi-Fi.
• Access points will be listed on the screen.
3. Tap the projector’s SSID.
Projection
Selecting a LAN Display input
1. Press the SOURCE button and select LAN DISPLAY.
• When the LAN Display input is selected, the splash screen for LAN Display appears on the screen.
Tablet computer
To USB-A terminal
USB wireless
LAN adapter
(option)
Important:
• Some USB wireless LAN adapters cannot be used depending on the specifications.
Wireless network setting on the tablet computer
1. Turn on the tablet computer and tap the [Settings] icon.
Starting WiFi-Doc
When using iOS
2. On the tablet computer, tap the WiFi-Doc icon “ “ to turn on WiFi-Doc.
• The program starts to search for projectors. When projectors are found, their SSID’s are displayed.
3. Select a projector for projection by tapping its SSID.
EN-52
Advanced display utilities (continued)
4. Select a file to be projected by tapping its name.
• The image of the selected file is displayed.
4. Select a file to be projected by tapping its name.
• The image of the selected file is displayed.
5. Operate the image by touching the tablet screen.
5. Operate the image by touching the tablet screen.
• Flick the screen to move to the previous or next page.
• Pinch the screen for zooming in or out.
• Tap the screen to display the status bar and the thumbnails of the pages. (See below.)
Status bar
• Flick the screen to move to the previous or next page.
• Pinch the screen for zooming in or out.
• Tap the screen to display the status bar and the thumbnails of the pages. (See below.)
Status bar
Thumbnails
• Tap [Back] to return to the file selection screen.
• Tap [OK] to stop the projection.
• Tap a thumbnail to select the page to be projected.
When using Android
2. On the tablet computer, tap the WiFi-Doc icon “ “ to turn on WiFi-Doc.
• The program starts to search for projectors. When projectors are found, their SSID’s are displayed.
3. Select a projector for projection by tapping its SSID.
Thumbnails
• Tap [Back] to return to the file selection screen.
• Tap [Play] or [Stop] to start or stop the projection.
• Tap a thumbnail to select the page to be projected.
Important:
• Restart the projection or starting projection from another tablet computer stops the projection from the current tablet computer and the “
X“ mark will appear in the middle of the screen. Tapping the “
X“ mark will start projection from the tablet computer again.
EN-53
Ending WiFi-Doc
6. Turn off WiFi-Doc on the tablet computer.
Advanced display utilities (continued)
Thin client
Projecting the desktop screen of a remote computer connected via a network onto the projector, you can remotely control the remote computer through the projector.
To use the thin client function, you need to install the software “ThinClient.exe” contained in the attached
CD-ROM.
Supported OS’s are as follows:
• Windows XP (except Home Edition)
• Windows Vista (except Home Basic and Home
Premium)
• Windows 7 (except Starter and Home Premium)
• Windows Server 2008 R2
• Windows MultiPoint Server
Important:
• License terms for Windows XP, Windows Vista and
Windows 7 do not permit simultaneous operation by multiple users.
• To use the thin client function with Windows Server
2008 R2 or Windows MultiPoint Server, a Client
Access License (CAL) is required. For details, see
"Client Access License (CAL)" on page 58.
Preparation for using Remote Desktop
The thin client function utilizes the standard Microsoft
Remote Desktop function. To use the Remote Desktop function, perform the following preparations on the computer.
Important:
• For the following preparations, log on to the computer using the administrator account.
1. Creating a user account
Important:
• You must configure a password for the user account.
Do not use double-byte characters for the user account name and password.
2. Configuring Remote Desktop users
Configure the Remote Desktop users as follows.
In Windows Vista, Windows 7, Windows Server
2008 R2 or Windows MultiPoint Server
1. Select [Start]-[Control Panel].
2. In Windows Vista, select [System and Maintenance].
Otherwise, select [System and Security].
• When using Classic View in Windows Vista, double-click the System icon and go to step 4.
3. Select [System].
4. Click [Remote settings].
5. Select [Allow connections from computers running any version of Remote Desktop (less secure)].
6. Click [Select Users...].
• The “Remote Desktop Users” window is displayed.
EN-54
Advanced display utilities (continued)
7. Click [Add...].
• The “Select Users” window is displayed.
8. Enter the user account name configured in the “1.
Creating a user account” (see page 54) in the
textbox and click [OK].
• The “Remote Desktop Users” window is displayed.
9. Click [OK].
In Windows XP
1. Select [Start]-[Control Panel].
2. Click [Performance and Maintenance].
• When using Classic View, double-click the
System icon and go to step 4.
3. Click [System].
• The “System Properties” window is displayed.
4. Click the [Remote] tab and check the [Allow users to connect remotely to this computer] checkbox.
5. Click [Select Remote Users...].
• The “Remote Desktop Users” window is displayed.
6. Perform steps 7-10 in the section “
In Windows
Vista, Windows 7, Windows Server 2008 R2 or
Windows MultiPoint Server.”
3. Configuration of Windows Firewall
Configure Windows Firewall as follows.
In Windows 7, Windows Server 2008 R2 or
Windows MultiPoint Server
1. Select [Start]-[Control Panel].
2. Select [System and Security].
3. Select [Allow a program through Windows Firewall].
• The “Allowed Programs” window is displayed.
4. Check the [Remote Desktop] checkbox and the
[Home/Work (Private)] and [Public] checkboxes on the same line, and click [OK].
• The “System Properties” window is displayed.
10.Click [OK].
In Windows Vista
1. Select [Start]-[Control Panel].
2. Select [Allow a program through Windows Firewall].
• When using Classic View, double-click the
Windows Firewall icon and select [Allow a program through Windows Firewall] on the upper left of the window.
• The”Windows Firewall Settings” window is displayed.
EN-55
Advanced display utilities (continued)
3. Click the [Exceptions] tab, check the [Remote
Desktop] checkbox and click [OK].
Connection
Connect the projector and the computer using a commercially available LAN cable. Connect a USB mouse and USB keyboard to the USB-A terminal on the projector.
In Windows XP
1. Select [Start]-[Control Panel].
2. Click [Network and Internet Connections].
• When using Classic View, double-click the
Windows Firewall icon and go to step 4.
3. Select [Windows Firewall].
• The “Windows Firewall” window is displayed.
4. Click the [Exceptions] tab, check the [Remote
Desktop] checkbox and click [OK].
Installation of software
Installing Thin Client
Before starting installation, be sure to read
“ReadMe.txt” contained in the CD-ROM.
1. Copy “ThinClient_v200.exe” contained in the
TOOLS folder of CD-ROM to the hard disk of your computer.
2. Double-click “ThinClient_v200.exe” on the hard disk, and start up the installer of the Thin Client.
• Follow the on-screen instructions to install the software.
• When the “Windows Security Alert” window is displayed during installation, proceed as follows:
In Windows XP or Windows Vista, click
[Unblock].
In Windows 7, click [Allow access].
3. When the installation has been completed, restart the computer.
When deleting ThinClient (Uninstallation)
1. Select [Start]-[All Programs]-[Thin Client]-[Uninstall
Thin Client].
• Follow the on-screen instructions to uninstall the software.
Computer
To USB-A terminal
To LAN terminal
LAN cable
(option)
Wireless keyboard and mouse
Important:
• On Thin Client, use both a keyboard and mouse. We recommend a commercially available wireless keyboard and wireless mouse intended for a computer with wireless receiver.
• For wired LAN connection, use a category-5 LAN cable. Both straight-through and crossover cables can be used.
• The USB-A terminal on this projector is compatible with USB 2.0.
• Supported USB devices are standard USB HID devices with power consumption less than 5V/
500mA or wireless LAN modules.
• Some USB wireless LAN adapters cannot be used depending on the specifications.
• When using a USB hub, you are recommended to use the one with external power supply.
• Some USB hubs cannot be used depending on the specifications.
Operation
Selecting a LAN Display input
1. Press the SOURCE button and select LAN DISPLAY.
• When the LAN Display input is selected, the splash screen for LAN Display appears on the screen.
EN-56
Advanced display utilities (continued)
Connecting the projector to the computer
For the following operation, use the USB device such as a mouse or keyboard connected to the projector.
Important:
• The following key assignment is applied to any keyboard connected to the projector.
Esc F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12
~
`
Tab
!
1
Caps Lock
Shift
Q
A
@
2
Z
W
S
#
3
X
E
D
$
4
C
R
F
%
5
V
T
G
ˆ
6
B
Y
H
&
7
N
U
J
*
8
M
I
K
(
9
<
,
O
L
)
0
.
>
P
;
:
—
-
?
/
[
{
"
'
+
=
Shif t
Back space
]
}
Ente r
\
|
Ctrl
Win
Ke y
Al t A lt
Win
Ke y
Menu Ctrl
PrtSc ScrL k Pause
Ins Home PgUp NumLk
Del End PgD n
↑
← ↓ →
7
4
1
0
5
2
/
8
6
3
*
9
-
+
Ente r
2. Click the RDP icon “ “.
• “Waiting to search Thin Client server ...” is displayed. Then the logon window appears.
Important:
• In [TC Server], the name of the computer where
ThinClient.exe has been installed will be displayed.
• If the subnet of the computer is different, the computer name will not be displayed in [TC
Server].
• To close the logon window, click [CANCEL] or press the ESC key on the keyboard.
• The computer name may not be displayed just after startup of the computer. In that case, click
[CANCEL] or press the ESC key on the keyboard to close the logon window, wait for a while and then click the RDP icon again.
3. Enter the following in the textboxes and click [OK].
• [TC Server]: Enter the computer name (or IP address).
• [User name]: Enter the user account name.
• [Password]: Enter the password.
Important:
• Double-byte characters cannot be used.
• “Waiting to connect ...” is displayed and the connection process will start. It may take some time to display the desktop screen depending on the network congestion. Wait for a while until the desktop screen appears.
• When connecting to a computer with different subnet, enter the IP address in [TC Server].
• If the message saying “This computer is not allow to remote desktop.” is displayed, the Remote
Desktop users setting may not have been enabled yet. Make the setting again, following the procedure of “Preparation for using Remote
• If you enter a wrong User name or Password,
“The projector could not log on. Make sure your
User name and Password are correct.” will be displayed.
EN-57
• If you connect to a computer installed with
Windows XP, Windows Vista or Windows 7 that any other user has already logged on, “Another user is currently logged on to this computer.” will be displayed.
• If you connect to a computer with Windows
Server 2008 R2 or Windows MultiPoint Server and try logging on to a user account where any other user has already logged on, “Another user is currently logged on to this computer.” will be displayed.
4. When the projector logs on to the computer, the desktop screen of the user account is displayed.
• You can operate the computer using the USB device such as a mouse or keyboard connected to the projector.
Disconnecting the projector from the computer
For the following operation, use the USB device such as a mouse or keyboard connected to the projector.
Important:
• When you disconnect the connection without ending the session, the programs running on the computer are kept active. Therefore, when you establish the connection next time, you can resume the programs from where you disconnected the session.
When using Windows XP
To disconnect without ending the session:
5. Select [Start]-[Disconnect].
6. Click [Disconnect].
To disconnect with ending the session:
5. Select [Start]-[Log Off].
6. Click [Log Off].
When using Windows Vista
To disconnect without ending the session:
5. Select [Start]-[X].
• Lock function of Remote Desktop cannot be used with this projector. When [Lock] is selected, the remote session is disconnected without ending the session.
To disconnect with ending the session:
5. Click [Start], select the
X button and click [Log Off].
When using Windows 7, Windows Server 2008 R2
or Windows MultiPoint Server
To disconnect without ending the session:
5. Click [Start], select the
X button and click
[Disconnect].
• Lock function of Remote Desktop cannot be used with this projector. When [Lock] is selected, the remote session is disconnected without ending the session.
To disconnect with ending the session:
5. Select [Start]-[Log Off].
Advanced display utilities (continued)
Client Access License (CAL)
An application allowing multiple users to share a single operation system requires the standard Microsoft
Windows server licenses. In addition to Windows
Server Client Access License, Remote Desktop
Services Client Access License (RDS CAL) is necessary for each end user or each device to access Windows server. When using Windows Multipoint Server,
Windows MultiPoint Server 2011 CAL is also necessary.
For details of Microsoft multiple user licenses, see the
Microsoft website.
1. When the host computer OS is Windows XP, Windows Vista or Windows 7
For Windows XP, Windows Vista and Windows 7, only a single projector can run the thin client function. While using the desktop of host computer, you cannot use the thin client function on the projector.
2. When the host computer OS is Windows Server
2008 R2
Windows Server requests Client Access License (CAL).
To access the host computer from a thin client computer or projector, two types of CAL are necessary:
“Windows Server CAL” and “Windows Remote Desktop
Service (RDS) CAL”. “Windows Server CAL” offers two types of license system.
User CAL
With User CAL, you purchase CALs according to the number of users regardless of the number of thin client computers or projectors. User CAL is, therefore, recommended in the case that the number of system administrators or operators who operate thin client computers or projectors at multiple sites is smaller than that of the thin client computers or projectors.
Device CAL
With Device CAL, you purchase CALs according to the number of devices accessing to the host, regardless of the number of users who access the host via thin client computer or projector. Therefore Device CAL is recommended for the case that multiple operators share a thin client computer or projector.
In the example above, the following licenses are necessary.
• Windows Server CAL (Device CAL) x 4
• Windows RDS CAL x 4
3. When the host computer OS is Windows
MultiPoint Server
The concept of Windows MultiPoint Server is basically the same as that of Windows Server 2008 R2. It requires Windows MultiPoint Server CAL instead of
Windows RDS CAL. Therefore, Windows Server CAL and Windows MultiPoint Server CAL are necessary for each user or device. When you use the desktop of host computer as one of computer terminals, Windows
MultiPoint Server will also request a Windows Server
CAL and Windows MultiPoint Server CAL for the desktop of host computer.
(Example 1)
When two users operate four computers or projectors as well as the desktop of host computer
• Windows Server CAL (User CAL) x 2
• Windows MultiPoint Server CAL x 2
(Example 2)
When six users operate four computers or projectors as well as the desktop of host computer
• Windows Server CAL (Device CAL) x 4
• Windows MultiPoint Server CAL x 4
In the example above, the following licenses are necessary.
• Windows Server CAL (User CAL) x 2
• Windows RDS CAL x 2
EN-58
Advanced display utilities (continued)
USB VIEWER
You can project JPEG images and the PtG contents stored in the USB device such as a USB flash drive without using a computer.
Also, you can perform effective presentation of them using the AutoRun function and the slideshow function.
To create PtG contents, you need to install the software
“PtG Converter-Lite” contained in the attached
CD-ROM.
Important:
• Supported USB Flash drive format is FAT32.
• Only one logical partition in USB Flash drive is supported.
• Supported USB device is standard USB mass storage device with power consumption less than
5V/500mA.
• JPG file preview limitation:
• File size:
• Pixel:
10 MB or less
40 megapixel (24 bits) or less
• Dimension: 8192*6144 or less
• File Name: ASCII characters are supported.
• Thumbnail: file thumbnail (obtained from EXIF) is supported.
• PtG file preview limitation:
• File Name: ASCII characters are supported.
• Thumbnail: file thumbnail is supported.
• USB VIEWER does not support the following image:
• Extended DCT-based process
• Lossless process
• Hierarchical process
• Progressive scan
• Input format of YUV4:1:1, gray level with 16x16 pixels MCU
• Decoded image width less than 64 pixels for
YUV4:2:0/4:2:2 and 32 pixels for YUV4:4:4
• Decoded height less than 32 pixels
• Source images of 12-bits per sample
Installation of PtG Converter-Lite
About PtG Converter-Lite
PtG Converter-Lite is a software which converts PPT files created by Microsoft Office PowerPoint into PtG files that can be projected by USB VIEWER. Pause/ page marks and animations contained in the PPT files are also converted.
Features
• Converting up to 20 pages of PPT
• Converting into 800 x 600 / 1024 x 768 / 1280 x
800*16bpp PtG
System requirement
• CPU:
IntelR PentiumR M processor 1.5 GHz or above
• Memory:
256 MB or more (recommended)
• OS:
Windows XP, Windows Vista and Windows 7
• Microsoft Office:
Microsoft Office 2003, Microsoft Office 2007 and
Microsoft Office 2010
EN-59
Installing PtG Converter-Lite
Before starting installation, be sure to read
“ReadMe.txt” contained in the CD-ROM. Copy “PtG
Converter-Lite_v200.exe” contained in the TOOLS folder of CDROM to the hard disk of your computer.
1. Double-click “PtG Converter-Lite_v200.exe”, and start up the installer of the PtG Converter-Lite.
2. Follow the on-screen instructions to install the software.
When deleting PtG Converter-Lite (Uninstallation)
Important:
• When uninstalling PtG Converter-Lite, it should be ended in advance. If the application continues operating, uninstallation cannot be performed normally.
1. Select [Start]-[All Programs]-[PtG Converter]-[Uninstall].
2. Follow the on-screen instructions to uninstall the software.
• Logs and setting files are automatically deleted.
Conversion of a PPT file to PtG file using the PtG Converter-Lite
1. Click the PtG Converter-Lite icon “ “ to execute the program.
Menu bar PPT conversion button
• Menu bar
Right-click to open the menu.
• Output Resolution:
Selects the resolution of the PtG file after the conversion.
• Max Circle Animation:
Selects the max time of animation.
• About:
Displays the software version information.
• Exit:
Exits the PtG Converter-Lite.
• PPT conversion button:
Starts the conversion from the PPT file to the PtG file.
2. Click the PPT conversion button.
• The file selection screen appears.
Advanced display utilities (continued)
3. Select the PPT file you want to convert, and click
[Open].
• The screen for specifying the file destination and name appears.
Performing the USB VIEWER
Selecting a USB VIEWER input
1. Press the SOURCE button and select USB VIEWER.
• When the USB VIEWER input is selected, the USB
VIEWER screen appears.
4. Set the file destination and the name.
• The converted file is stored in the same folder as original file by default.
• The name of the converted file is the same as original file’s by default.
5. Click [OK] to start conversion.
6. When the conversion has been completed, click
[OK].
Setting up
2. Press the
S or T button on the remote control to select Setup and press the ENTER button.
• The Setup screen appears.
Important:
• All the animation effects available on a computer display can be converted. However, the followings are not supported.
• Animation effects with the timer setting or the repeat setting
• Animation effects taking 60 seconds or more in a single movement
• Pages having more than 3 second downtime setting
• VBA object embedded files
• OLE object embedded files
Connection
Connect a USB device to the USB-A terminal on the projector.
To USB-A terminal
USB device
(option)
Important:
• The USB-A terminal on this projector is compatible with USB 2.0.
• Do not use a USB hub for the connection.
3. Press the
S or T button to select a setting item and press the
W or X button to change the setting.
• AutoRun:
Enables or disables the AutoRun and slideshow function.
OFF
PtG
AutoRun
Disables.
Enables for PtG files.
Photo Enables for JPEG files.
Slideshow
Disables.
Enables for all files.
Enables for all files.
• Interval:
Sets the interval for PtG pause mark or photo slideshow to 5/10/30/60/300 seconds.
• Repeat:
Enables or disables the repeat execution of
AutoRun and slideshow function for photo files and PtG file.
• Sorting:
Sets the file sorting rule to File Name (Ascending),
File Name (Descending), Time (New to Old) or
Time (Old to New).
4. To return to the USB VIEWER screen, press the
ENTER button.
EN-60
Advanced display utilities (continued)
Displaying PtG file
5. Press the
S or T button on the remote control to select Presentation to Go and press the ENTER button.
• The file selection screen appears.
6. Press the
S or T button to select a file or folder you want to display and press the ENTER button.
• If you select a folder, the underlying file names are displayed. Then, select a file.
• An image on page 1 is displayed on the screen.
7. Change the page by pressing the
S , T or X button.
•
S button: to previous page
•
T button: to next page
•
X button: to next pause
8. Press the
W button to quit the display.
• The screen goes back to the file selection screen.
Displaying JPEG file
5. Press the
S or T button on the remote control to select Photo Viewer and press the ENTER button.
• The file selection screen appears.
6. Press the
S or T button to select a file or folder you want to display and press the ENTER button.
• If you select a folder, the underlying file names are displayed. Then, select a file.
• The image of the selected file is displayed on the screen.
7. Change the file by pressing the
S, T or X button.
•
S button: to previous file
•
T button: to next file
•
X button: to next file
8. Press the
W button to quit the display.
• The screen goes back to the file selection screen.
Displaying with AutoRun function
5. Create an “AUTORUN” folder in the root directory of the USB device using a computer or other.
6. Save a PtG file or JPEG files in the AUTORUN folder.
Important:
• The AutoRun function supports single PtG file only. The PtG file located on the top by sorting is played if multiple PtG files exists in AUTORUN folder.
7. Connect the USB device to the USB-A terminal.
• The files specified by the AutoRun setting (PtG or
Photo) are played back automatically.
8. Press the ENTER button to start or pause the playback.
9. Press the
S, T or X button to change the file to be played back.
•
S button: to previous page/previous file
•
T button: to next page/next file
•
X button: to next pause/next file
10.Press the
W button to quit the AutoRun display.
• The screen goes back to the file selection screen.
Displaying with slideshow function
5. Press the
S or T button on the remote control to select Presentation to Go or Photo Viewer and press the ENTER button.
• The file selection screen appears.
6. Press the
S or T button to select a file or folder you want to display and press the ENTER button.
• If you select a folder, the underlying file names are displayed. Then, select a file.
• When a PtG file is selected, the file is displayed with the slideshow.
• When a JPEG file is selected, all the files in the same folder as the JPEG file exists are displayed with the slideshow.
7. Press the ENTER button to start or pause the playback.
8. Press the
S ,T or X button to change the file to be played back.
•
S button: to previous page/previous file
•
T button: to next page/next file
•
X button: to next pause/next file
9. Press the
W button to quit the slideshow.
• The screen goes back to the file selection screen.
Ending the USB VIEWER
Unplug the USB device from the projector. Before unplugging, be sure to press the UNPLUG button on the remote control and select [Yes] on the screen by pressing the
W or X button and then ENTER button.
EN-61
Advanced features
Displaying a user-defined image during startup or muting
You can display your desired image as the startup screen (or splash screen). Using the menu, you can also use it as the background that is displayed while the video is muted or no signal is inputted.
Important:
• You can capture the computer images from the
COMPUTER1, COMPUTER2, HDMI1, HDMI2, LAN
DISPLAY, USB DISPALY or USB VIEWER input sources.
Procedure
(See page 25 for menu setting.)
1. Select the input source COMPUTER1,
COMPUTER2, HDMI1, HDMI2, LAN DISPLAY, USB
DISPALY or USB VIEWER.
2. Display your desired image.
3. Display the INSTALLATION ADVANCED menu.
4. Select IMAGE CAPTURE by pressing the
S or T button.
5. Press the ENTER button.
• When the capture starts, the captured image will be displayed.
• When you press ENTER button once, any button doesn’t function until the capture completes.
• When image resolution is lower than 1024 x 768
(for TX20U) or 1280 x 800 (for TW21U), the image is captured by adjusting its resolution to 1024 x
768 (for TX20U) or 1280 x 800 (for TW21U).
• When image resolution is higher than 1024 x 768
(for TX20U) or 1280 x 800 (for TW21U), the image area of 1024 x 768 (for TX20U) or 1280 x 800 (for
TW21U) is only captured.
Important:
• You can’t change the new startup screen back to the original startup screen. (Even when you select
RESET ALL in the FEATURE menu, the factory default screen isn’t available any longer.) When you want to change the startup screen again, capture another image.
• The captured image will be displayed from the next startup. If the captured image isn’t displayed, make sure that the setting of SPLASH SCREEN in the
ADVANCED MENU of the INSTALLATION menu isn’t
• The captured images will be deleted at the same time as pressing the ENTER button. If you pressed
ENTER button wrongly, try to capture the same images again.
• To display the captured image while the video is muted, set AV MUTE MODE in the ADVANCED
MENU of the INSTALLATION menu to IMAGE. (See
• When BACK COLOR in the ADVANCED MENU of the INSTALLATION menu is set to IMAGE, the captured image is displayed while no signal is inputted.
• Some images can’t be captured correctly because of their signal type.
Password function
This projector is equipped with the password function that is designed for prevention of wrong operation by children and restriction on operation by other than specified users. The password function has 3 modes as follows.
DISPLAY INPUT ..........When the projector is turned on, the startup screen (or splash screen) will appear and stay on the screen until the password is entered.
When the password is entered, the startup screen will switch to the regular operation screen.
MENU ACCESS ...........All the buttons except for the
POWER button on the projector are disabled. (The buttons on the remote control are enabled.) You can use this mode as a measure of prevention of wrong operation by children and restriction on operation by other than specified users.
SPLASH ID SCREEN ...SPLASH SCREEN in the
INSTALLATION menu become unavailable. SPLASH
SCREEN will be set to ON automatically.
To enable the password function:
1. Display the FEATURE menu.
2. Press the
S or T button to select PASSWORD
FUNCTION.
3. Press the
W or X button to change the mode among
DISPLAY INPUT , MENU ACCESS and SPLASH
ID SCREEN .
• When the password has already been set, the mode won’t be changed. In such cases, press the
ENTER button to cancel the password function and try again.
4. Press the ENTER button.
• The screen for setting the password function will appear.
5. Press the ENTER button.
• The screen for entering a password will appear.
EN-62
6. Enter a 4 - 8 digit password using the
S, X, T and
W buttons.
(
S=1, X=2, T=3, W=4)
Advanced features (continued)
7. Press the ENTER button.
• To cancel the procedure, press the MENU button.
8. Enter the password again for confirmation using the same steps.
9. Press the ENTER button.
• If the entered passwords don’t match, an error message will appear.
• To cancel the procedure, press the MENU button.
To cancel the password function:
1. Display the FEATURE menu.
2. Press the
S or T button to select PASSWORD
FUNCTION.
3. Press the ENTER button.
• The screen for canceling the password function will appear.
Magnifying the displayed image
By pressing the MAGNIFY button on the remote control, you can magnify the image to view the details.
• While viewing the image from the COMPUTER1,
COMPUTER2, HDMI1, HDMI2, LAN DISPLAY, USB
DISPALY or USB VIEWER input source, you can magnify the image.
4. Press the ENTER button.
• The screen for entering the password will appear.
5. Enter a 4 - 8 digit password using the
S, X, T and
W buttons.
(
S=1, X=2, T=3, W=4)
6. Press the ENTER button.
• If you enter a wrong password, an error message will appear.
• To cancel the procedure, press the MENU button.
Important:
• You can disable the password by pressing the
MENU and ENTER buttons on the projector at the same time for about 3 seconds.
Magnified image
To use the MAGNIFY mode:
1. Press the MAGNIFY button on the remote control.
• You can select the area to be magnified by pressing the
S, T, W or X button on the remote control.
• You can change the magnification of the selected area by pressing the + or - button.
2. Press the MAGNIFY button again to exit the
MAGNIFY mode.
• The regular operation screen will appear.
Important:
• The MAGNIFY mode doesn’t function with some input signals.
• In the MAGNIFY mode, you cannot perform the following:
• Volume control
• Viewing 3D images
EN-63
Advanced features (continued)
Freeze
To stop the motion in the image temporarily (or to display a still image):
Press the FREEZE button on the remote control.
• The image will freeze temporarily.
To resume the motion in the image:
Press the FREEZE button on the remote control again.
• The image will be unfrozen.
Important:
• Do not display a still picture for a long time because the afterimages may persist on the screen. (See
Presentation timer
By pressing the TIMER button on the remote control, you can set up and display presentation timer on the screen.
To display the TIMER:
1. Press the TIMER button on the remote control.
• The TIMER menu appears at the center of the screen.
EFFICIENT MODE
By pressing the EFFICIENT MODE button, you can display the EFFICIENT MODE menu and also set the following menu items: LAMP MODE, STANDBY MODE, and AUTO POWER OFF.
(For details of each item, see page 27.)
1. Press the EFFICIENT MODE button on the remote control.
• The EFFICIENT MODE menu appears.
2. Select an desired item to set by pressing the
S or T button.
3. Set the selected item by pressing the
W or X button.
4. Repeat steps 2-3 for each setting.
5. Press the EFFICIENT MODE button to exit the menu.
2. Press the
S or T button to adjust the timer period.
• The timer period can be set between 1 to 60 minutes.
• The default timer period is 10 minutes.
• The timer period changes 1-minute per step during the period is 1 to 20 minutes and 5-minute per step during the period is 20 to 60 minutes.
3. Press the ENTER button to start the coutdown.
• The countdown timer appears on top right corner of the screen.
• When other OSD appears, the TIMER dialog disappears temporarily. The TIMER dialog reappears after the other OSD disappeared.
• When the countdown is finished, it continues to count until the time reaches -10 minutes. Then the dialog disappears.
• To stop the timer, press TIMER button and when a confirmation dialog appears, press the ENTER button.
• If the input source is changed while the timer is working, the timer stops.
EN-64
Advanced features (continued)
Supervising and controlling by computer
You can supervise and control the projector’s operation using a personal computer via a LAN network.
Major functions
ProjectorView Global+
Batch projector controlling / supervising application software
• Batch operation of stand-alone projector / multiple projectors
• Scheduling function to turn ON/OFF for each day of the week
• Checking each condition of the projector and detecting a theft
• Setting of the projector’s IP Config
• Activating Visual PA2 to display the specified characters on the projector’s screen
AMX Device Discovery
The projector is monitored and controlled by the controller system of AMX.
Crestron RoomView Connected™
The projector is monitored and controlled by the controller system and software of Crestron Electronics,
Inc.
PJLink™
This projector supports standard protocol PJLink™ for projector control and you can control and monitor projector’s operations using the same application among projectors of different models and different manufacturers.
About ProjectorView Global+
• For details, see “LAN control UTILITY operation manual” in the CD-ROM.
About AMX Device Discovery
• This is a technology suggested by AMX to facilitate configuration of the control system of
AMX and its target devices.
For details, see the website of AMX.
URL http://www.amx.com/
About PJLink™
• To use PJLink™ function, the PJLink™ application software is required.
• To use this function, set the network certification properly according to the setting of the network application to be used. (See page 33.)
• For the specifications of PJLink™, access to the
Web site of Japan Business Machine and
Information System Industries Association
(JBMIA). (http://pjlink.jbmia.or.jp/english)
• This projector is fully compliant to the specifications of JBMIA PJLink™ Class 1. It supports all the commands defined by PJLink™
Class 1, and the compliance has been verified with the PJLink™ standard specifications Version
1.0.
Important:
• For the commands for PJLink™, see the table on the next page.
• The control may not be performed correctly or the monitoring data may not be obtained correctly in the following conditions:
• During standby
• During input source switching
• During auto position execution
• During AV mute
• During command processing
• Before the splash screen disappears after the power is turned on.
• During AV mute, etc., it may take approx. 5 seconds to receive a response to a command.
• Use 1 controller to control/monitor 1 projector.
• For how to control/monitor using PJLink™, see the operation manual of the PJLink™ application you use.
• When you monitor the projector’s operating state using this function by issuing inquiry commands successively, issue an inquiry command after receiving the response to the previous inquiry command from the projector.
About Crestron RoomView Connected™
• This is a technology suggested by Crestron
Electronics, Inc. to facilitate configuration of the control system of Crestron and its target devices.
For details, see the website of Crestron
Electronics, Inc.
URL http://www.crestron.com
URL http://www.crestron.com/getroomview/
EN-65
Advanced features (continued)
Connection
For details of the connection, see “LAN control UTILITY operation manual” in the CD-ROM.
When STANDBY MODE of the INSTALLATION menu of the projector is set to LOW, the LAN network is
disabled. To enable the LAN network, set STANDBY MODE to LAN. (See page 27.)
Configure the initial network settings first.
details of ProjectorView Global+, see “LAN control UTILITY operation manual” in the CD-ROM.
Using the User Manual
The User Manual for LAN Control Utility is prepared in the Portable Document Format (PDF) in the CD-ROM.
Opening the User Manual:
1. Load the CD-ROM into the CD-ROM drive.
2. Open CD-ROM “PROJECTOR.”
3. Double-click on “MANUAL_LAN.HTML” within the CD-ROM. A language selection list for the User Manual will be displayed.
4. Move the mouse pointer to the desired language and click.
PJLink™ supported commands
The table below shows commands to control the projector using the PJLink™ protocol.
Command
POWR
POWR ?
INPT
INPT ?
Description
Power control
Inquiry about the power state
Input switching
Inquiry about input switching
Remark (Parameter)
0 = Standby
1 = Power on
0 = Standby
1 = Power on
2 = Cooling down
3 = Warming up
11 = COMPUTER1 12 = COMPUTER2
21 = VIDEO 22 = S-VDEO
31 = HDMI1 32 = HDMI2
41 = USB VIEWER 42 = USB DISPLAY
51 = LAN DISPLAY
AVMT
AVMT ?
Mute control
Inquiry about the mute state
30 = Video and audio mute disable
31 = Video and audio mute enable
ERST ?
LAMP ?
INST ?
NAME ?
Inquiry about the error state
Inquiry about the lamp state
Inquiry about the available inputs
Inquiry about the projector name
1st byte: Fan error, 0 or 2
2nd byte: Lamp error, 0 to 2
3rd byte: Temperature error, 0 or 2
4th byte: Cover open error, 0 or 2
5th byte: Always 0
6th byte: Other error, 0 or 2
0 to 2 mean as follows:
0 = No error detected, 1 = Warning, 2 = Error
1st value (1 to 5 digits):
Cumulative lamp operating time (This item shows a lamp operating time
(hour) calculated based on that Lamp Mode is Low.)
LAMP MODE "LOW" is included "LOW1" and "LOW2".
2nd value: 0 = Lamp off, 1 = Lamp on
The following value is returned.
“11 12 21 22 31 32 41 42 51”
The projector name set on the Network Config menu or the Crestron
RoomView Setup window is returned.
INF1 ?
INF2 ?
INF0 ?
CLSS ?
Inquiry about the manufacturer name
Inquiry about the model name
Inquiry about other information
Inquiry about the class information
“MITSUBISHI” is returned.
“TX20” or “TW21” is returned.
No other information is available. No parameter is returned.
“1” is returned.
• This projector is fully compliant to the specifications of JBMIA PJLink™ Class 1. It supports all the commands defined by
PJLink™ Class 1, and the compliance has been verified with the PJLink™ standard specifications Version 1.0.
EN-66
Lamp replacement
This projector is equipped with a lamp to project images. This lamp is a consumable. It may burn out or its brightness may decrease during use. In such cases, replace the lamp with a new one as soon as possible.
Be sure to replace the lamp with a new lamp separately sold that is exclusive to this projector. Contact your dealer for purchase of the lamp.
Spare lamp for TX20U/TW21U: VLT-TX20LP
Caution:
• Do not remove the lamp immediately after using the projector. You may get burned because the lamp is very hot after use.
• Before replacing the lamp, press the POWER button to turn off the lamp and wait for two minutes for lamp to cool down. Unplug the power cord from wall outlet and wait one hour for the lamp to cool down completely.
• Do not remove the lamp except for replacement.
Careless handling can cause injury or fire.
• Do not touch the lamp directly. It may break and cause injury or burn.
• Be sure not to drop the lamp lid screw into the projector. Also be sure not to put metal or any flammable objects inside because it may cause fire or electric shock. If any objects should fall inside, unplug and contact your dealer.
• Install the lamp securely to prevent failure and fire.
• If the lamp should break, small glass fragments may fall out through the grilles and some may remain inside of the projector or the lamp box. When taking the lamp box out, be sure to turn over the projector and hold the handle of the lamp box to avoid injury due to the glass fragments.
• If the lamp should break, never shake the lamp box or hold it in front of your face after removing it. The glass fragments may fall out and cause injury to your eyes.
• Be sure to use the lamp dedicated to this projector,
VLT-TX20LP for TX20U/TW21U. Use of other lamps may cause a failure of the projector.
A) When the projector is placed on the table
Make sure that the projector is securely held in place.
1. Remove the cover (a) of the screw fixing the lamp cover with a fingernail. If it is difficult to remove it with a fingernail, use a finetipped tool such as flathead screwdriver.
(a)
2. Remove the screw (b) and slide the lamp cover (c) for removal.
(c)
(b)
3. Loosen the two screws (d) of the lamp unit, and then pull out the lamp unit (f) by the handle (e).
(f)
(d)
(e)
Caution:
• When replacing the lamp, do not loosen the screws other than two screws (d). It may cause the failure of projector.
• Pull the lamp unit out of the projector slowly. If it is pulled out quickly, the lamp may break, scattering glass fragments
• Do not spill liquid on the removed lamp unit or do not place it near any flammable object or where children can reach to prevent injuries or fire.
4. Insert the new lamp unit, and secure it with two screws firmly.
5. Secure the lamp cover with screw (b) back again, and mount the cover (a).
Caution:
• Make sure that the lamp cover is secured firmly.
Otherwise, the POWER indicator flashes red and green, disallowing the projector to be powered on.
EN-67
Lamp replacement (continued)
B) When the projector is mounted to the ceiling
When removing the lamp unit from the projector mounted to the ceiling, never fail to use the lamp replacement attachment to protect yourself from glass fragments and so on.
In case that you pull a lamp out without using a lamp replacement attachment for some reason, such as to check the lamp, please dismount the projector from ceiling mounting holder to start the procedure with projector put on the table for safety reasons.
When you have to execute the procedure without dismounting the projector from ceiling mounting holder as well as without using a lamp replacement attachment, please make sure that you take appropriate safety measure, such as wearing protective glasses and mask, and that no one is around before you start the procedure.
Avoid executing the procedure right under the projector, especially around the lamp cover, for fear that glass debris might fall.
IF YOU GET GLASS DEBRIS IN THE EYE OR MOUTH,
CALL A PHYSICIAN.
• Contact your dealer when replacing the lamp unit with the projector mounted to the ceiling.
1. Remove the lamp cover referring to the procedure 1 and 2 of “A) When the projector is placed on the table”.
Caution:
• When opening the lamp cover to replace the lamp of the ceiling-mounted projector, pay careful attention because glass fragments may exist inside the lamp cover.
2. Loosen the two screws (d) of the lamp unit.
(d)
Caution:
• When replacing the lamp, do not loosen the screws other than two screws (d). It may cause the failure of projector.
3. Pull out the lamp unit (g) by the handle (h).
(g)
(h)
EN-68
Caution:
• Pull the lamp unit out of the projector slowly. If it is pulled out quickly, the lamp may break, scattering glass fragments.
• Do not spill liquid on the removed lamp unit or do not place it near any flammable object or where children can reach to prevent injuries or fire.
4. Insert the new lamp unit, and secure it with two screws firmly.
5. Secure the lamp cover with screw (b) back again, and mount the cover (a).
Caution:
• Make sure that the lamp cover is secured firmly.
Otherwise, the POWER indicator flashes red and green, disallowing the projector to be powered on.
Reset of the lamp operation time
Plug in the power cord, and reset the lamp operation time by keep pressing the the
W, X, and POWER buttons on the control panel simultaneously for three seconds.
Important:
• Unless these three buttons are pressed at the same time, the lamp operation time isn’t reset.
• Make sure that the STATUS indicator is lit twice and the lamp operation time is reset successfully.
• The projector doesn’t turn on if the lamp cover isn’t attached securely.
• Be sure to reset the lamp operation time whenever you replace the lamp.
• Do not reset the lamp operation time unless you replace the lamp.
Caution:
• The lamp is fragile. If it is broken, be careful not to cut yourself with glass fragments.
• Contact your dealer for a new lamp.
Interval of lamp replacement
The recommended interval of lamp replacement is about 6000 hours*1*2 of consecutive use. Such interval differs depending on the operating environment and may be shorter than 6000 hours
*1*2
.Decrease in luminescence and/or color brightness indicates that the lamp needs to be replaced. When the lamp operation time exceeds 4500 hours
*1
, the indicator will blink alternately between green and red (while the lamp is lit; when the lamp is not lit, the indicator will be lit red only) and the lamp replacement message will appear on the screen for one minute everytime the lamp is turned on.
When the lamp has been used for about 5700 hours
*1
, the replacement message (LAMP REPLACEMENT) will appear on the screen for one minute every 30 hours
*1 thereafter. When the lamp operation time exceeds
6000hours
*1*2
, the projector automatically shuts off
Lamp replacement (continued)
and can’t be used until the lamp is replaced and the lamp operation time is reset.
*1: Duration when LAMP MODE of the INSTALLATION menu is set to LOW. When it is set to STANDARD, this duration will be shorted.
LAMP MODE "LOW" is included "LOW1" and
"LOW2".
*2: When LAMP MODE is set to STANDARD, this duration will be shorted to 3000 hours.
Important:
• Do not open the lamp cover when the projector is set at a ceiling or a high place. Lamp fragments may fall from the inside if the lamp were broken.Please
contact your dealer when you need to replace the lamp with a new one.
Caution:
• This projector uses a lamp that contains mercury. Disposal of the lamp or the projector with the lamp may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the
Electronic Industries Alliance: www.eiae.org. (For the U.S. only.)
EN-69
Troubleshooting
Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be sure to unplug the power plug, and then contact your dealer.
No image appears on the screen.
Problem
Power can not be turned on.
Solution
• Check whether the indicators are on or off and how they are lightning.
POWER
Off
Steady red
STATUS
Off
Off
Blinking orange
Blinking green
Steady red
Solution
• Connect the power cord to the projector.
• Plug the power cord into a wal outlet.
• If any objects are blocking the air inlet or outlet grille, remove them and carry out the following.
1. Unplug the power cord from the wall outlet.
2. Make sure that the projector has cooled off.
3. Plug the power cord into the wall outlet.
4. Press the POWER button.
• If any objects are blocking the air inlet or outlet grille, remove them.
• Don’t expose the air outlet grilles to hot air emitted from a heating appliance.
• After the STATUS indicator stops blinking, press the POWER button.
• If you unplug the power cord while the fan is rotating, the lamp may not turn on about 1 minute when you plug the power cord next time.
• The lamp can’t turn on again for 1 minute after it goes out.
• Press the POWER button several times.
• Replace the lamp. (The lamp is at the end of its life.)
• Attach the lamp cover on the top.
Off
Blinking red/green
• Unplug the power cord from the wall outlet and contact your dealer.
Steady
Or
Blinking
No image appears on the screen.
• Cancel the AV mute by pressing the AV MUTE button.
• It may take about 1 minute for the lamp to light up.
• The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
• If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the POWER button may not work after the power cord is plugged. Press the POWER button to turn back on the POWER indicator.
• Check that the intake vent is clean.
•
Check that the lamp cover is closed. (See page 67 or 76.)
• Check that the cables connected to the external devices are not broken.
• When an extension cable is being used, replace it with the supplied cable for check.
When images are displayed correctly, add an RGB signal amplifier to the extension cable.
EN-70
Troubleshooting (continued)
No image appears on the screen. (continued)
Problem
Power turns off.
The screen for entering the password appears.
“NO SIGNAL” is displayed.
Solution
• This problem may occur when the intake vent and/or exhaust vents are blocked. (In such a case, the STATUS indicator brinks orange.)
J Remove the objects blocking the intake vent and/or exhaust vents and then carry out the following procedure.
1. Wait for the intake fan and/or exhaust fan to stop. (Wait until the STATUS indicator goes out.)
2. Unplug the power cord from the wall outlet.
3. Wait about 10 minutes.
4. Plug the power cord into the wall outlet.
5. Press the POWER button.
• When the STATUS indicator is steady red, it is indicating that the lamp should be replaced. Replace the lamp in this case.
• Check that AUTO POWER OFF in the INSTALLATION menu has been set to OFF.
• If the lamp has deteriorated, it may go out after a while it illuminates.
• PASSWORD FUNCTION in the FEATURE menu has been set to DISPLAY INPUT to enable the password lock.
J Enter the password or contact the person in charge of management of the
• Turn on the power of the connected device, or check whether there is something wrong with the connected device.
• Check whether the external device output signals. (Check this especially when the external device is a laptop computer.)
• Check that the cable connected to the external device isn’t defective.
• Check that the projector is connected to the external device using the correct terminals.
• Check that the connected device is correctly selected as the input source.
• When an extension cord is being used, replace it with the supplied cable and check whether images are projected correctly. If images are projected correctly, use an
RGB signal amplifier along with the extension cord.
Images are not displayed correctly.
Problem
Projected images are shaking.
Projected images are displaced.
Projected images are distorted.
Projected images are dark.
Solution
• Check that the cable connected to the external device isn’t intermittent.
• Connect the cable’s plug with the external device’s connector firmly.
• Project an image containing a lot of characters without black areas and press the
AUTO POSITION button.
• Some computers output out-of-spec signals on rare occasion. In such a case, change the setting of the SIGNAL DETECT in the FEATURE menu and press the
AUTO POSITION button. If the position (and size) of the projected images is still incorrect, make adjustment using the SIGNAL menu. (For details, see flowchart on
• Adjust the projector and the screen so that they are perpendicular to each other.
• Use the flat screen.
•
Adjust BRIGHTNESS and CONTRAST in the IMAGE menu. (See page 26.)
• 3D images displayed on the projector appear darker. It is normal and does not mean the projector is malfunctioning.
• When viewing 2D images, set 3D FORMAT to AUTO (for HDMI input only) or set
3D in the IMAGE menu to OFF. (When AUTO is selected, only 3D images become darker.)
•
Replace the lamp. (See page 67.)
EN-71
Troubleshooting (continued)
Images are not displayed correctly. (continued)
Problem
Projected images are blurred.
Afterimages persist on the screen.
Solution
•
Adjust the focus. (See page 19.)
• Clean the lens.
• Press the
W or X button on the remote control to eliminate flicker.
•
Adjust TRACKING and FINE SYNC. in the SIGNAL menu. (See page 30.)
•
Set OVER SCAN in the SIGNAL menu to 100%. (See page 30.)
•
Set the keystone adjustment to 0 using the KEYSTONE button. (See page 17.)
•
Set the projected image size to maximum (0) in DIGITAL ZOOM function.(See page
•
Adjust BRIGHTNESS and CONTRAST in the IMAGE menu. (See page 26.)
• Adjust the projector and the screen so that they are perpendicular to each other.
• This phenomenon is improved by keeping projecting an evenly bright image. (Such
“image burn-in” phenomenon where afterimages persist on the screen may occur if a stationary image is kept displayed on the screen for a long time.)
• This phenomenon is normal for a DLP™ projector and is not a malfunction. (A very small number of pixels may visibly or invisibly be persistent all the time, but they are not a sign of system malfunctions. Over 99.99% of the pixels are effective.)
White dots are seen on projected images. Black dots are seen on projected images.
Fine streaks are seen on projected images.
Projected images become wavy.
Hue is not appropriate.
Tint in projected images is incorrect.
Different color tint.
Only the motion areas in the images supplied from the computer aren’t displayed.
• This is due to interference with the screen surface and is not a malfunction. Replace the screen or displace the focus a little.
• Vertical or horizontal streak noise may appear on the projected image, depending on the type of the DVD player, game console or computer you use. In such a case, you can reduce such streak noise by enabling the LPF.
• Connect the plugs of the cables to external devices securely.
• Keep the projector away from equipment generating interfering radio waves.
• When the keystone adjustment is carried out, the image may not be displayed correctly because of the type of input signal. This isn’t a product malfunction. In this case, readjust the keystone so that the amount of keystone correction is as small as possible.
• Check that the cables connected to the external devices are not broken.
• If the setting of COMPUTER INPUT in the SIGNAL menu is inconsistent with the
RGB/Y
C
B
C
R
output setting of the external device even when the input source is other than computer (for example, when the input source is HDMI1 or HDMI2), the entire image appears reddish or greenish.
•
Check that COMPUTER INPUT in the SIGNAL menu is correctly set. (See page 30.)
• Check that the cable connected to the external device isn’t broken.
• When comparing images projected by two projectors, tints in the displayed images may be different because of variation between their optical components. This is not a malfunction.
• When comparing the image projected by this projector with those displayed on the television or PC monitor, tints in the displayed images may be different because of difference in the range of color reproducibility. This is not a malfunction.
• This is caused by the computer being used. Contact the manufacturer of your computer.
EN-72
Troubleshooting (continued)
Images are not displayed correctly. (continued)
Problem
Projected images are obscured.
Noise appears around the image.
Projected images are flickering.
Projector images are twitching.
Solution
• Match the output resolution of your computer with the resolution of the projector.
For the method to change the output resolution of the computer, contact the
manufacturer of your computer. (See page 79.)
• Some images and texts appear obscured during the keystone adjustment. In such
cases, use the projector without applying the keystone adjustment. (See page 17.)
• In some images such as DVD, noise may appear around the recorded image. In this
case, decrease the setting value of OVER SCAN of the SIGNAL menu. (See page
• After the POWER button or ON button on the remote has been pressed, or the
LAMP MODE setting has changed, images may be flickering until the lamp lights stably. This is an expected behavior.
• When selecting the input signal, AUTO POSITION, and Image, the projected image may be flickering temporarily. This is not a product malfunction.
• During LAMP MODE LOW2 is switched, projector images are little bit flickering for a moment with constant timing. This phenpmenon is to keep lamp condition well and is not a malfunction.
• Projector may be vibrating. Set AUTO KEYSTONE to OFF or lower the VOLUME
T button of the Remote control.
Others
Problem
The exhaust vents emit warm air.
No audio is output.
Solution
• This air comes out after cooling the inside of the projector. You may feel hot, but this vis not a malfunction.
• Check that the volume isn’t set to low.
• When the external device is connected with an HDMI cable, set the audio output of the device to PCM output.
The menu can’t be used. • The microcomputers inside the projector may be wrongly operating because of noise.
J Press the POWER button to turn off the lamp and unplug the power cord from the wall outlet. Wait about 10 minutes, plug the power cord in, and try again.
“TEMPERATURE!!” is displayed.
• This indication appears when the ambient temperature rises high. When the ambient temperature stays high, the lamp goes out.
J Eliminate any causes of the rise in the ambient temperature.
• This indication appears when the air inlet or outlet grille is blocked. When they are kept blocked, the lamp goes out.
J Remove the objects blocking the air inlet or outlet grille.
The remote control doesn’t function easily or at all.
The fans sound during standby.
• This mark appears when ineffective operation is carried out. This isn’t a product malfunction.
• Check that the batteries are loaded in the remote control or the batteries are not
• Check that the remote control sensor isn’t exposed to direct sunlight or fluorescent
•
Use the remote control within its operation range. (See page 9.)
• Use the remote control at least 10 cm away from the projector.
• When STANDBY MODE is set to STANDARD, the fans rotate at very low speed during standby after plugging the power cord (with 5 second high speed rotation at the beginning) and after turning off the lamp. This is to cool down the projector operating various functions during standby and is not a malfunction.
EN-73
Troubleshooting (continued)
Others (continued)
Problem Solution
Abnormal sound is heard. • Because the color wheel spins at a high speed, metallic sounds may be heard in rare occasions. Such symptom is not a malfunction.
Fan sound increse suddenly during LAMP
MODE "LOW2".
Images are not 3D.
* Use commercially available 3D glasses supporting the DLP™
Link™ system. No 3D glasses are supplied with the projector.
There is something wrong with the 3D images.
* Use commercially available 3D glasses supporting the DLP™
Link™ system. No 3D glasses are supplied with the projector.
The 3D glasses don’t turn on.
* Use commercially available 3D glasses supporting the DLP™
Link™ system. No 3D glasses are supplied with the projector.
• During LAMP MODE LOW2 is switched, fan speed increase for a short time once per 30 minutes. This phenomenon is to keep lamp condition well and is not a malfunction.
•
•
Is the 3D mode of the projector set properly for the image?
J Set 3D FORMAT in the 3D menu of the projector properly for the image (AUTO
, SIDE BY SIDE
Are the batteries of the 3D glasses still working?
J If the 3D glasses don’t activate even when you turn on the power switch, replace or charge the batteries of the 3D glasses. For details, see the user manual of the
3D glasses.
, TOP AND BOTTOM , or FRAME SEQUENTIAL ).
• View 3D image from the front of the screen. At the angle to the screen, you may not be able to view proper 3D images.
• Is there any obstacle between the 3D glasses and the screen? Or, is there any sticker or label over the sensor of the 3D glasses?
J The 3D glasses work by receiving signals of the images being viewed. Check that there is no obstacle between the 3D glasses and the screen.
• Are you viewing images from a very close distance?
J Viewing images from a very close distance may not obtain the 3D effect. View images from a proper distance.
• The 3D glasses may become out of sync due to fluorescent light. Turn off the fluorescent light.
• Are the 3D glasses turned off?
J Turn on the 3D glasses.
•
The signals listed in the table on page 80 can be displayed in 3D format. You cannot
view other signals in 3D format even when you set 3D FORMAT in the 3D menu to
AUTO , SIDE BY SIDE , TOP AND BOTTOM , or FRAME SEQUENTIAL .
• You may not obtain the 3D effect depending on the capabilities of your computer
(including the graphic board, memory, and CPU).
• Some 3D glasses may not work with this projector. Ask the dealer for details.
• Depending on the 3D image status, you may feel something wrong with the 3D images.
J Switch the 3D SYNC INVERT setting of the projector to check whether or not such feeling is eliminated.
• The 3D glasses may become out of sync due to fluoescent light. Turn off the fluorescent light.
• View 3D images from the front of the screen. At an angle to the screen, you may not be able to view proper 3D images.
If the following problem occurs after the lamp is replaced, check the following first.
Problem
The projector does not turn on.
The STATUS indicator blinks.
Solution
•
Fit the lamp cover securely. (See pages 67 or 68.)
•
Reset the lamp operating time. (See page 68.)
•
Reset the lamp operating time. (See page 68.)
EN-74
Troubleshooting (continued)
Maintenance
Warning:
Do not use flammable solvents (benzene, thinner, etc.) and flammable aerosols when cleaning the projector body and lens. Flammable substances may ignite causing fire or breakdown while the lamp is illuminating.
Caution:
Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance on the projector.
Cleaning of the projector and the ventilation slots
Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft cloth dampened with diluted mild detergent, and then wipe them with a dry cloth.
To protect the surface of the projector from fading or deteriorating:
• Do not spray insecticide on or inside the projector.
• Do not use benzin or thinner to clean it.
• Do not let rubber or plastic materials contact with projector.
Cleaning of the lens
Use a standard lens-cleaning brush or a piece of lens tissue dampened with lens cleaning fluid. The lens surface is fragile. Use only recommended, nonabrasive lens-cleaning materials. Do not touch the lens with your fingers.
Kensington Lock
This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System.
Refer to the information that came with the Kensington System for instructions on how to use it to secure the projector. Please contact Kensington Technology Group below.
Kensington Technology Group
2855 Campus Drive
San Mateo, CA 94403, U.S.A.
Phone: +1- (650)572-2700Fax: +1- (650)572-9675
This projector has two indicators, each of which shows the operation condition of the projector.
The following offer solutions to possible problems. If these problem persist, turn the projector off and consult your dealer.
EN-75
Indicators
This projector has two indicators, each of which shows the operation condition of the projector. The following offer solutions to possible problems. If these problem persist, turn the projector off and consult your dealer.
POWER indicator
STATUS indicator
Normal condition
POWER STATUS CONDITION NOTE
Stand-by
Off
Steady red
Blinking green
Lamp stand-by for power-off
Lamp stand-by for power-on
The power cannot be turned on by pressing the POWER button.
The power cannot be turned off by pressing the POWER button.
Blinking green
Steady green
Steady green
Abnormal condition
POWER STATUS
Steady green
Or
Steady red
Steady red
Steady green
Steady red
Steady red
Blinking green/red
Blinking green/red
The power is on. (Normal condition)
Blinking orange
CONDITION POSSIBLE SOLUTION
Abnormal temperature
• The ventilation grilles is clogged with dust or dirt.
• The room temperature is high.
• Clean the ventilation grilles.
• Relocate the projector to a cooler place.
Blinking green
Blinking green/red
Blinking red
Steady red
The protection circuit is working or the lamp is in an abnormal condition.
• Wait until the STATUS indicator goes out, then press the POWER button.
• If the above solution is not effective, replace the lamp.
The lamp operation time exceeds the time elapsed until the lamp lifetime notice while the
The lamp operation time exceeds the time elapsed until the lamp lifetime notice while the
The lamp operation time exceeds the time
elapsed until the lamp lifetime. (See page 68.)
Replace the lamp.
Change with a new lamp if this problem recurs.
The lamp cover isn’t closed.
Close the cover correctly.
Off
Abnormal.
Contact your dealer.
Steady
Or
Blinking
EN-76
Specifications
Type
Model
Rated power supply
Power consumption
Display Technology
Colors
Projection lens
Light source lamp
Picture size
PC compatibility
Video compatibility
Speaker
S-video input
Video input
Audio input
Analog RGB input
HDMI input
DLP™ projector
TX20U
100 - 240 V AC, 50/60 Hz
3.5 A
During standby: 0.5W (when Standby Mode is Low)
0.55-inch single chip Digital Micromirror
Device (DMD)
Pixels: 1024 x 768 = 786432 pixels
16770000 colors
F 2.5 -2.8, f=18.4-22.0 mm
TW21U
0.65-inch single chip Digital Micromirror
Device (DMD)
Pixels: 1280 x 800 = 1024000 pixels
F 2.6 -2.9, f=21.0-25.6 mm
240 W
40 - 300 inch (Wide) (aspect ratio 4:3) 40–300 inch (Wide) (aspect ratio 16:10)
Resolution:640 x 480 (Expand) -
1024 x 768 (Real) -
1600 x 1200 (Compress)
Sync on Green available
Resolution:640 x 480 (Expand) -
1280 x 800 (Real) -
1600 x 1200 (Compress)
Sync on Green available
NTSC/NTSC 4.43/PAL (including PAL-M, N)/SECAM/PAL-60
Component Video (DVD/HDTV) (480i, 576i, 480p, 576p, 1080i, 720p, 1080p)
16 W mono x 1
Luminance signal: 1.0 Vp-p 75
Ω (negative sync.)
Chroma signal: 0.286 Vp-p 75
Ω (burst signal)
1.0 Vp-p 75
Ω (negative sync.)
350 mVrms, 10 k
Ω or more
RGB: 0.7 Vp-p 75
Ω (negative sync.)
YP
B
P
R
/YC
B
C
R
:
Y: 1.0 Vp-p (negative sync.)
P
B
P
R
/
C
B
C
R
: 0.7 Vp-p
HD/CS: TTL level (positive or negative)
VD: TTL level (positive or negative)
HDMI 19-pin
HDMI interface (TMDS single link) (only PCM audio is supported)
SERIAL terminal (RS-232C), LAN terminal (RJ-45)
319 x 103 x 224 mm (width x height x depth)
Control connector
Outside dimensions
(not including protrusion)
Weight
Length of power cord
Temperature, humidity
(performance guaranteed)
Approx. 2.8 kg
71 inch (1.8 m)
+41°F (+5°C) - +95°F (+35°C), 30 - 90%
Approx. 2.8 kg
• The specifications and outside appearance of the projector are subject to change without prior notice.
EN-77
Specifications (continued)
Connectors
COMPUTER/COMPONENT VIDEO IN, MONITOR OUT (Mini
D-SUB 15-pin)
11 15
6 10
COMPUTER/COMPONENT
VIDEO IN
12
13
14
15
8
9
10
11
Pin No.
1
2
3
6
7
4
5
Spec.
R (RED)/C
GND
GND
GND
GND
GND
DDC 5V
GND
GND
DDC Data
HD/CS
VD
R
G (GREEN)/Y
B (BLUE)/C
DDC Clock
B
1 5
MONITOR OUT
Pin No.
3
4
1
2
9
10
11
12
7
8
5
6
13
14
15
Spec.
R (RED)/C
R
G (GREEN)/Y
B (BLUE)/C
B
-
GND
GND
GND
GND
-
GND
-
-
HD/CS
VD
-
HDMI (HDMI 19-pin)
1 19
2
18
16
17
18
19
12
13
14
15
Pin No.
1
2
3
4
5
6
7
8
9
10
11
Spec.
TMDS Data 2 +
TMDS Data 2
Shield
TMDS Data 2 -
TMDS Data 1 +
TMDS Data 1
Shield
TMDS Data 1 -
TMDS Data 0 +
TMDS Data 0
Shield
TMDS Data 0 -
TMDS Clock +
TMDS Clock
Shield
TMDS Clock -
CEC
-
SCL
SDA
DDC Ground
+5 V Power
Hot Plug Detect
Dimension drawing (unit: mm)
SERIAL (D-SUB 9-pin)
6 9
1 5
7
8
5
6
9
Pin No.
Name
3
4
1
2
-
TXD
RXD
-
GND
-
-
-
-
-
-
-
-
-
I/O
-
IN
OUT
-
319
What’s included in the box
AC power cord*
Computer cable for the U.S.
for Europe for the U.K.
for Australia for South Korea
J2552-0063-03
J2552-0247-00
J2552-0065-02
J2552-0053-00
J2552-0247-00
J2552-0072-05
Remote control
Safety Manual/Quick Start up
CD-ROM
Battery (2)
* One of power cords for the U.S., Europe, U.K., Australia, and South Korea is provided appropriately.
Replacement part (option/not included in the box)
Spare lamp: VLT-TX20LP
EN-78
Specifications (continued)
Supported input signal
Signal mode Resolution
(H x V)
Horizontal frequency
(kHz)
Vertical frequency
(Hz)
Normal mode*1
TX20U
(H x V)
Normal mode*1
TW21U
(H x V)
Plug and Play*2
COMPUTER/
COMPONENT
VIDEO IN-1/2 terminal
HDMI1/2 terminals
SXGA75
SXGA85
SXGA+60
SXGA+75
MAC13
MAC16
MAC19
HP75
SUN66a
SUN76a
SUN66
SUN76
SGI72
SGI76
UXGA60
SVGA75
SVGA85
XGA60
XGA70
XGA75
XGA85
XGA120
SXGA70a
SXGA75a
SXGA85a
WXGA60
WXGA60a
WXGA60b
WXGA60c
WXGA+60
WXGA120a
SXGA60b
SXGA75b
SXGA85b
SXGA60
TV60, 480i (525i)
TV50, 576i (625i)
1080i60 (1125i60)
1080i50 (1125i50)
480p (525p)
576p (625p)
720p60 (750p60)
720p50 (750p50)
1080p60 (1125p60)
1080p50 (1125p50)
1080p24 (1125p24)
CGA84
CGA85
VGA60
VGA72
VGA75
VGA85
SVGA56
SVGA60
SVGA72
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1152 x 864
1152 x 864
1280 x 768
1280 x 800
1360 x 768
1366 x 768
1440 x 900
1280 x 800
1280 x 960
1280 x 960
1280 x 960
1280 x 1024
720 x 480
720 x 576
1920 x 1080
1920 x 1080
720 x 480
720 x 576
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
1920 x 1080
640 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
1280 x 1024
1280 x 1024
1400 x 1050
1400 x 1050
640 x 480
832 x 624
1024 x 768
1024 x 768
1152 x 900
1152 x 900
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1600 x 1200
47.77
49.70
47.71
47.71
55.94
101.56
60.00
75.00
85.94
63.98
46.88
53.67
48.36
56.48
60.02
68.68
97.55
63.85
67.50
77.49
27.00
37.86
37.86
31.47
37.86
37.50
43.27
35.16
37.88
48.08
15.73
15.63
33.75
28.13
31.47
31.25
45.00
37.50
67.50
56.25
79.98
91.15
65.32
82.28
35.00
49.72
60.24
62.94
61.85
71.81
71.68
81.13
76.92
82.01
75.00
59.87
59.81
60.01
59.79
59.89
119.91
60.00
75.00
85.00
60.02
75.00
85.06
60.00
70.07
75.03
85.00
119.99
70.01
75.00
85.06
24.00
84.13
85.08
59.94
72.81
75.00
85.01
56.25
60.32
72.19
59.94
50.00
60.00
50.00
59.94
50.00
60.00
50.00
60.00
50.00
75.02
85.02
59.98
74.87
66.67
74.55
75.02
74.92
66.00
76.64
66.68
76.11
72.30
76.00
60.00
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 615
1024 x 640
1024 x 579
1024 x 576
1024 x 640
1024 x 640
1024 x 768
1024 x 768
1024 x 768
960 x 768
1024 x 768
1024 x 768
1024 x 576
1024 x 576
1024 x 768
1024 x 768
1024 x 576
1024 x 576
1024 x 576
1024 x 576
1024 x 576
1024 x 640
1024 x 640
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
960 x 768
960 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
984 x 768
984 x 768
960 x 768
960 x 768
960 x 768
960 x 768
1024 x 768
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1280 x 768
1280 x 800
1280 x 724
1280 x 720
1280 x 800
1280 x 800
1066 x 800
1066 x 800
1066 x 800
1000 x 800
1066 x 800
1066 x 800
1280 x 720
1280 x 720
1066 x 800
1066 x 800
1280 x 720
1280 x 720
1280 x 720
1280 x 720
1280 x 720
1280 x 800
1280 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1000 x 800
1000 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1024 x 800
1024 x 800
1000 x 800
1000 x 800
1000 x 800
1000 x 800
1066 x 800
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
*1: Indicates the resolution when ASPECT in the FEATURE menu is set to NORMAL.
*2: Signals marked with O in the Plug and Play column are described in EDID (extended display identification data) of the projector.
Signals described in the Signal mode column can be input regardless of the O mark in the Plug and Play column. For signals not marked with O in the Plug and Play column, the resolution may not be supported even when it is supported on the computer.
EN-79
Specifications (continued)
3D supported signal
Signal mode Resolution
(H x V)
Horizontal frequency
(kHz)
Vertical frequency
(Hz)
Normal mode*1
TX20U
(H x V)
Frame packing
Side by side
720p50
720p60
1080p24
1080p24
1080p50
1080p60
1080i50
1080i60
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
Top and bottom
720p50
720p60
720p50
720p60
1280 x 720
1280 x 720
1280 x 720
1280 x 720
1080p24
1080p50
1080p60
TV60, 480i (525i)
1920 x 1080
1920 x 1080
1920 x 1080
720 x 480 Frame sequential
(Field sequential)
1080i60 (1125i60) 1920 x 1080
480p (525p) 720 x 480
720p60 (750p60) 1280 x 720
1080p60 (1125p60) 1920 x 1080
VGA60
SVGA60
XGA60
XGA120
WXGA60a
WXGA120a
640 x 480
800 x 600
1024 x 768
1024 x 768
1280 x 800
1280 x 800
37.50
45.00
37.50
45.00
27.00
56.25
67.50
15.73
75.00
90.00
54.00
27.00
56.25
67.50
28.13
33.75
33.75
31.47
45.00
67.50
31.47
37.88
48.36
97.55
49.70
101.56
1024 x 576
1024 x 576
1024 x 576
1024 x 576
1024 x 576
1024 x 576
1024 x 576
1024 x 576
1024 x 576
1024 x 576
1024 x 576
1024 x 576
1024 x 576
1024 x 576
1024 x 576
1024 x 768
1024 x 576
1024 x 768
1024 x 576
1024 x 576
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 640
1024 x 640
50.00
60.00
50.00
60.00
24.00
50.00
60.00
59.94
50.00
60.00
24.00
24.00
50.00
60.00
50.00
60.00
60.00
59.94
60.00
60.00
59.94
60.32
60.00
119.99
59.81
119.91
*1: Indicates the resolution when ASPECT in the FEATURE menu is set to NORMAL.
1280 x 720
1280 x 720
1280 x 720
1280 x 720
1280 x 720
1280 x 720
1280 x 720
1280 x 720
1280 x 720
1280 x 720
1280 x 720
1280 x 720
1280 x 720
1280 x 720
1280 x 720
1066 x 800
1280 x 720
1066 x 800
1280 x 720
1280 x 720
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1280 x 800
1280 x 800
Normal mode*1
TW21U
(H x V)
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
COMPUTER/
COMPONENT
VIDEO IN-1/2 terminals
-
-
O
O
-
O
VIDEO and
S-VIDEO terminals
-
O
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
HDMI1/2 terminals
O
-
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Important:
• Some computers aren’t compatible with the projector.
• The projector’s maximum resolution is 1024 x 768 pixels (TX20U) or 1280 x 800 pixels (TW21U). It may not display images of higher resolutions than its maximum resolution correctly.
• Images with SYNC on G (Green) signal may jitter.
• Images with SYNC on G (Green) signal may be tinged with green.
• If the resolution and frequency of your computer aren’t shown on the table, find the compatible resolution and frequency by changing the resolution of your computer.
• Set COMPUTER INPUT in the SIGNAL menu to RGB when inputting the HDTV signal as RGB signal.
• This projector doesn’t support 480p signals from video devices having 4 lines (R, G, B, CS*) or having 5 lines (R, G, B, H, V).
* : Composite Sync
• TV60 and TV50 are equivalent to 480i and 576i respectively. When these signals are supplied to the COMPUTER/COMPONENT
VIDEO IN-1 or IN-2 terminal, the signal mode is indicated as 480i or 576i.
EN-80
Ver. 1.0
1 Zusho Baba, Nagaokakyo-City, Kyoto Japan
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project