Epson EMP-TS10 Projector User Guide

E
Printed on 100% recycled paper.
Printed in Japan
402171700
(9002556)
02.01-.*A(C05)
About The Manuals and Notations Used
Types of Manual
The documentation for your EPSON projector is divided into the following four manuals. Refer to the
manuals in the order given below.
Unpacking and Installation Guide
This manual contains information on the procedures from unpacking the projector through to starting to use the
projector, and also describes the included accessories.
Safety Instructions/ World-Wide Warranty Terms
This manual contains information on using the projector safely, and also includes safety instructions, worldwide warranty terms and a troubleshooting check sheet.
Be sure to read this manual thoroughly before using the projector.
Setup Guide
This manual describes the preparations required in order to start using the projector (such as remote control
preparation and connecting video equipment or a computer).
User’s Guide (this manual)
This User’s Guide contains information on basic operation, using the projector menus, troubleshooting and
maintenance.
Notations used in this User’s Guide
General information
Indicates procedures where personal injury or damage to the projector may occur if the
procedures are not followed correctly.
Indicates additional information and points which may be useful to know regarding a topic.
Indicates that an explanation of the underlined word or words in front of this symbol appears
in the glossary of terms.
Refer to the Glossary in the Appendix. (p.63)
Procedure
Indicates operating methods and the order of operations.
The procedure indicated should be carried out in the order of the numbers.
Meaning of "unit" and "projector"
When "unit" or "projector" appears in the text of this User’s Guide, they may refer to items which are
accessories or optional equipment in addition to the main projector unit itself.
Contents
Environment Setting Menu Functions and Operations .......................................... 20
Video Menu................................................................................................................... 20
Audio Menu .................................................................................................................. 23
Setting Menu................................................................................................................. 23
User's Logo Menu......................................................................................................... 24
Advanced Menu ............................................................................................................ 25
About Menu .................................................................................................................. 26
Reset All Menu ............................................................................................................. 27
Using the Menus ........................................................................................................... 28
Useful Functions When a Computer is Connected................................................ 30
A/V Mute ...................................................................................................................... 30
Freeze............................................................................................................................ 30
E-Zoom ......................................................................................................................... 31
P in P (Picture in Picture) ............................................................................................. 32
Troubleshooting
Using the Help ....................................................................................................... 36
When Having Some Trouble .................................................................................. 37
When the Indicators Provide No Help.................................................................... 39
Settings and Useful
Functions
Settings and Useful Functions
Troubleshooting
Turning On the Projector.......................................................................................... 6
Connecting the Power Cord ............................................................................................ 6
Turning On the Power and Projecting Images ................................................................ 7
Turning Off the Projector.......................................................................................... 9
Adjusting the Screen Image................................................................................... 11
Adjusting the Image Size.............................................................................................. 11
Adjusting the Image Angle ........................................................................................... 11
Correcting Keystone Distortion .................................................................................... 12
Adjusting the Image Quality................................................................................... 14
Focusing the Screen Image ........................................................................................... 14
Selecting the Color Mode ............................................................................................. 14
Selecting the Image Aspect Ratio ................................................................................. 15
Adjusting Computer Images ......................................................................................... 16
Adjusting the Volume ............................................................................................. 18
Basic Operations
Features of the Projector ......................................................................................... 2
Basic Operations
Maintenance .......................................................................................................... 46
Cleaning ........................................................................................................................ 46
Replacing Consumables................................................................................................ 47
Saving a User's Logo............................................................................................. 51
Optional Accessories ............................................................................................. 53
List of Supported Signal Resolutions..................................................................... 54
Component Video Input/ RGB Video Input ................................................................. 54
Composite Video/ S-Video Input.................................................................................. 54
Computer ...................................................................................................................... 55
Specifications......................................................................................................... 56
Appearance ........................................................................................................... 58
Part Names and Functions .................................................................................... 59
Front/ Top...................................................................................................................... 59
Control Panel ................................................................................................................ 60
Rear ............................................................................................................................... 61
Base............................................................................................................................... 61
Remote Control............................................................................................................. 62
Glossary ................................................................................................................ 63
Index ...................................................................................................................... 65
Appendices
Appendices
1
Features of the Projector
Includes horizontal and vertical keystone correction functions for
projecting at an angle
Keystone distortion in the projected image
can be easily corrected, not only vertically
but horizontally also.
This allows images to be projected correctly
even if the projector is not set up directly
perpendicular to the screen. (p. 12)
Compact and lightweight
The projector has a compact body with a footprint the size of an A4 page
(274 (D) x 348 (W) x 104 (H) mm (10.79 (D) x 13.7 (W) x 4.09 (H) inches) and
is light in weight (approximately 4.2kg (9.3 lbs)).
Equipped with five color modes
The optimum images can be projected simply
by selecting the desired color mode from the
following five preset modes in accordance
with the images being projected. No complex
color adjustments are required.
Dynamic
Theatre
Natural
PC
sRGB
(p. 14)
Brilliant, Attractive Images
Despite its compact size, the projector can display images at high resolutions
with a high degree of luminance, providing beautifully clear images even in bright
environments.
Adoption of a short focal-length lens that can project onto 80-inch screens
at distances of 2.5m (8.2 ft.)
This lens is ideal for projecting onto
large indoor screens. The projector
can also project onto 100-inch screens
in rooms with an area of about 10 m2.
(Setup Guide)
80-inch
screen
2.5m
2
3
Basic
Operations
This chapter describes basic operations such as turning
projection on and off and adjusting the projected images.
Turning On the Projector ...................................6
•
Connecting the Power Cord ............................................... 6
•
Turning On the Power and Projecting Images.................. 7
Turning Off the Projector...................................9
Adjusting the Screen Image............................ 11
•
Adjusting the Image Size .................................................. 11
•
Adjusting the Image Angle ............................................... 11
•
Correcting Keystone Distortion ....................................... 12
Adjusting the Image Quality............................ 14
•
Focusing the Screen Image ............................................... 14
•
Selecting the Color Mode.................................................. 14
•
Selecting the Image Aspect Ratio..................................... 15
• For SDTV ..........................................................................................15
• For HDTV ..........................................................................................15
• Changing the display position for 16:9 display .................................15
•
Adjusting Computer Images ............................................ 16
• Automatic adjustment ........................................................................16
• Adjusting the tracking........................................................................16
• Adjusting the sync .............................................................................17
•
Adjusting the Volume ........................................................ 18
5
Turning On the Projector
This section describes the procedure from turning on the power to projecting images.
Be sure to read the separate Safety Instructions/ World-Wide Warranty Terms and check the
points that must be noted before using the projector to project images.
Connecting the Power Cord
Procedure
1
Check that the power is turned off for all
components connected to the
projector.
2
Connect the computer or other video
source to the projector.
(Setup Guide).
3
Remove the lens cover.
Place your finger
under the top of the
lens cover and pull
to remove the cover.
4
5
Connect the accessory power cord to
the projector.
Check that the power cord connector is facing the
same way as the power inlet on the projector, and
then insert the power cord connector securely into
the projector.
Lights orange
Connect the other end of the power
cord to a grounded electrical outlet.
Wait until the indicator lights orange.
The buttons on the projector’s control panel
and remote control cannot be operated
while the
indicator is flashing orange.
Wait until it lights steadily.
6
Connecting the Power Cord
Turning On the Power and Projecting Images
Turning On the Power and Projecting Images
Procedure
1
2
Basic Operations
Turn on the power for all equipment
connected to the projector.
For a video source, press the [Play] button at the
video source to start playback if necessary.
Check that the indicator on the projector has
stopped flashing and lights orange.
When using the remote control, set the
R/C switch on the remote control to ON.
3
Lights green
Remote control
Press the [Power] button on either the
remote control or the projector's
control panel to turn on the power for
the projector.
The indicator flashes green, and after a short
period projection starts.
Check that the indicator has stopped flashing
and lights green. (This takes approximately 30
seconds.)
The buttons on the remote control and the projector's control panel cannot be operated
while the
indicator is flashing green. Wait until it lights steadily.
The message "No-Signal." may appear depending on the projector's menu settings. (p.24)
4
If more than one signal source has been connected, use the remote control or
control panel buttons to select the port which the signal source that you
would like to use is connected to, while referring to the following table.
Port
Button to press
Control panel
Remote control
Computer1
[Comp1]
[Computer/YCbCr ]
Computer2/Component
Video
S-Video
Video
[Comp2/YCbCr]
[Video]
[S-Video]
[Video]
Display at bottom-left of
screen *
Computer1(Digital-RGB)
Computer1(Analog-RGB)
Computer1(RGB-Video)
Computer2(Analog-RGB)
Computer2(RGB-Video)
Computer2(YCbCr)
Computer2(YPbPr )
S Video
Video
*The display disappears after 3 seconds.
7
Connecting the Power Cord
Turning On the Projector
Turning On the Power and Projecting Images
• If only one signal source has been connected, the signals from that source will be
projected without needing to press one of the buttons from the previous table.
• If the "No-Signal." message does not disappear, check the connections again.
• If a laptop computer or a computer with an LCD screen has been connected to the
projector, the images may not be projected straight away. After making the connections,
check that the computer has been set up to output signals.
The following table shows examples of how to toggle output settings. For details, refer to
the section of the documentation provided with your computer under a heading such as
"External output", "Connecting an external monitor" or similar.
NEC
[Fn]+[F3]
8
Panasonic
[Fn]+[F3]
Toshiba
[Fn]+[F5]
IBM
[Fn]+[F7]
Sony
[Fn]+[F7]
Fujitsu
Macintosh
[Fn]+[F10]
After startup, change the
Control Panel adjustments
so that Mirroring is active.
Turning Off the Projector
Follow the procedure below to turn off the power of the projector.
Procedure
1
2
3
Basic Operations
Turn off the power for the signal
sources that are connected to the
projector.
Check that the power for all connected
components has been tuned off.
Press the [Power] button on either the
remote control or the projector's
control panel.
The confirmation message shown left will appear.
If you do not wish to turn off the power, press any
other button.
If you do not press any button, the message will
disappear automatically after 7 seconds (the
power will not turn off).
Power
Help
Computer/YCbCr
Video
Press the [Power] button once more.
The lamp unit will turn off and the indicator
will flash orange as the cool-down period
starts.
Source
Menu
Esc
Sync+
Tr cking
t
Tr cking +
Projector
4
Remote control
Lights orange
Check that the indicator has changed
to light orange.
When the indicator lights orange, cool-down is
complete.
The cool-down period lasts for approximately 2
minutes. (This varies depending on factors such
as the ambient air temperature.)
The buttons on the projector’s control panel
and remote control cannot be operated
while the
indicator is flashing orange.
Wait until it lights steadily.
5
If not using the projector for long
periods of time, disconnect the power
plug from the electrical outlet.
Do not disconnect the power cord from the outlet while the indicator is still
flashing orange. If you disconnect the power cord while the indicator is still flashing,
it may result in errors in projector operation and reduce the lamp unit operating life.
9
Turning Off the Projector
6
Set the R/C switch on the remote control
to the OFF position.
If you leave the R/C switch at the ON
position, the remote control will continue to
consume battery power.
Move the R/C switch to the OFF position
when not using the remote control.
7
8
10
Retract the front adjustable foot if it is
extended.
Gently push down on the projector while pressing
the foot adjust button.
Attach the lens cover.
Attach the lens cover to the lens when not using
the projector, in order to stop the lens from
getting dusty or dirty.
Adjusting the Image Size
Correcting Keystone Distortion
Adjusting the Image Angle
Adjusting the Screen Image
You can adjust the screen image in order to obtain the best possible picture.
Adjusting the Image Size
The size of the projected image is basically determined by the distance from the projector to the screen.
(Setup Guide)
The following procedures explain how to adjust the screen image once the projector itself has been set up.
Turn to Wide to
increase the size
Turn the zoom ring on the projector to
adjust the image.
The image can be enlarged in this way to 1.35
times the normal size.
If you would like to enlarge the image further,
move the projector further away from the screen.
(Setup Guide)
Basic Operations
Turn to Tele to
reduce the size
Procedure
Zoom ring
If a computer is connected, you can press the [Resize] button
on the projector's control panel or on the remote control to
switch between the real display and resized display.
• Resized display (default):
The images are processed so that they automatically fill the
whole of the projection area, regardless of the resolution
setting.
• Normal sized display (window display):
The images are projected at the same resolution that they are
input. The image size and the projection area may be different
depending on the resolution.
Keystone
Shift
Sync-
Resize
A/V Mute
Volume
Projector
Remote control
Adjusting the Image Angle
The projector should be as perpendicular to the screen as possible.
Seen from above
Seen from the side
If the projector cannot be set up so that it is exactly perpendicular to the screen, it can be set up so that it is
tilting slightly horizontally or vertically. To tilt the projector upward, adjust the front adjustable foot to tilt the
projector at an angle of up to a maximum 12°.
Procedure
Foot adjust button
While pressing the foot adjust button,
lift up the front of the projector so that
the front adjustable foot can extend.
Extend the front adjustable foot until the desired
angle is obtained, and then release the foot adjust
button.
To retract the foot, press and hold the foot adjust
button and gently lower the projector.
11
Adjusting the Screen Image
• When the foot is adjusted, it may cause the projected images to become distorted. Use the
keystone correction function to adjust this distortion.
• If the projector is tilted horizontally, turn the rear adjustable foot to adjust the angle.
Rear adjustable
foot
Extend
Retract
Correcting Keystone Distortion
When the projector is set up at an angle, keystone distortion may appear in the projected images. If the
projector is adjusted to within a range of approximately 30° vertically or 10° horizontally, the keystone
correction function can be used to adjust this keystone distortion.
The values given here are for when the image is at the smallest zoom setting (telephoto). The maximum
angles will be smaller if the zoom setting has been increased in the wide angle direction. Furthermore, if the
projector has been tilted both vertically and horizontally, the maximum adjustable angle will again be smaller
than the maximum angle if the projector had been tilted in only one direction.
•
When tilted vertically
Approx. 30° above
Approx. 30° below
30°
30°
•
When tilted horizontally
Approx. 10° to the right
Approx. 10° to the left
10°
10°
12
Adjusting the Image Size
Correcting Keystone Distortion
Adjusting the Image Angle
Procedure
Correcting vertical keystone distortion
Press the
or
button
on the projector's control
panel to adjust.
Esc
Menu
Tracking -
Auto
Shift
Esc
Sync+
Sync+
Tracking +
Tracking -
Keystone
Shift
Auto
Keystone
Sync-
Sync-
Resize
Resize
Projector
Tracking +
Basic Operations
Menu
Projector
Correcting horizontal keystone distortion
Press the
or
button
on the projector's control
panel to adjust.
Menu
Esc
Menu
Tracking -
Auto
Shift
Esc
Sync+
Sync+
Tracking +
Tracking -
Keystone
Shift
Sync-
Resize
Projector
Auto
Tracking +
Keystone
Sync-
Resize
Projector
Procedure to follow if using both horizontal and vertical keystone correction:
1.
2.
3.
4.
With the front adjustable foot retracted, set the projector so that it is fully horizontal.
Extend the front adjustable foot to adjust the angle as necessary.
Adjust the vertical keystone distortion until both sides of the picture are vertical.
Adjust the horizontal keystone distortion until the top and bottom edges of the picture are both horizontal.
• When keystone correction is carried out, the projected image will become smaller.
• The keystone correction settings are memorized, so that if you change the position or angle of
•
•
•
•
•
•
the projector, you may need to readjust the keystone correction settings.
To return a previous keystone correction to the initial setting, carry out the following operations.
To initalize vertical keystone correction: While holding down the
button, press the
button
for 1 second or more.
To initalize horizontal keystone correction: While holding down the
button, press the
button for 1 second or more.
If there is any noticeable irregularity in the projected images after keystone correction has been
carried out, reduce the sharpness. (p.21, 22)
Keystone correction can also be carried out using the projector’s environment setting menu.
(p.23)
If you carry out both horizontal and vertical keystone correction, the correction range will
become smaller than it would be if only one type of correction was carried out.
If the value displayed in the gauge on the screen stops changing when horizontal or vertical
keystone correction is being carried out, it indicates that the limit for horizontal or vertical
keystone correction has been exceeded. Check that the projector has not been set up at an
angle which exceeds the proper limit. (p.12)
If the horizontal (or vertical) keystone correction function is used at the same time that the EZoom or P in P function is being used, the keystone correction amount may change when the EZoom or P in P function is operated while the keystone correction amount is near the limit value.
The limit value for keystone correction will vary depending on the image signal being input.
13
Adjusting the Image Quality
The quality of the screen images can be adjusted as follows.
Focusing the Screen Image
Turn the focus ring to adjust the image
focus.
• If the surface of the lens is dirty or misted
over as a result of condensation, it may
not be possible to adjust the focus
correctly. If this happens, clean or de-mist
the lens. (p.46)
• If the distance from the projector to the
screen is less than 0.9 m (3.0 ft.), the
focus will not be correct. Check the
distance between the projector and the
screen.
Focus ring
Selecting the Color Mode
The following five color modes have been preset for use with images with varying characteristics. You can
use these color modes to obtain the optimum image quality easily, just by selecting whichever color mode
best suits the images. The brightness of the projected images will vary depending on the mode.
Mode name
Use
Dynamic
Ideal for projecting images with greater modulation and intensity.
Theatre
Ideal for enjoying presentations such as movies which have large numbers of dark scenes.
Natural
Ideal for enjoying presentations in a natural atmosphere.
PC
Ideal for use in making images as bright as possible when projecting computer images.
sRGB
Images conform to the sRGB standard. If the connected video source has an sRGB mode, set both the
projector and the video source to sRGB.
Press buttons [1] to [5] on the remote
control to select the color mode.
Procedure
Remote control
The color mode setting can also be changed using the Color Mode command of the projector's
Video menu. (p.21, 22)
14
Focusing the Screen Image
Selecting the Image Aspect Ratio
Selecting the Color Mode
Adjusting Computer Images
Selecting the Image Aspect Ratio
This function changes the aspect ratio of video images from 4:3 to 16:9 when video images are being
projected. Images which have been recorded in digital video or onto DVDs can be viewed in 16:9 widescreen format.
The aspect ratio changes each time the
[Resize] button on either the remote
control or the projector's control panel is
pressed.
Resize
A/V Mute
Volume
Projector
Basic Operations
Procedure
Remote control
For SDTV
4:3 display
16:9 display
When 16:9 output (squeeze mode) images
are displayed with an aspect ratio of 4:3,
the images are compressed horizontally
and elongated vertically.
4:3 display
When 16:9 output (squeeze mode) images
are displayed with an aspect ratio of 4:3,
the center portion of the image is
displayed in the whole of the screen.
For HDTV
16:9 display
Changing the display position for 16:9 display
Center
Top
Bottom
While holding down
the [Shift] button on
the projector's control
panel, press the
[Resize] button. The
display position
changes as shown left
each time the [Resize]
button is pressed in
this way.
15
Adjusting the Image Quality
Adjusting Computer Images
Automatic adjustment
Computer images can be adjusted automatically to the optimum images.
Automatic adjustment involves adjustment of the following three items:
Tracking , Display position and Sync (synchronization) .
Procedure
While an image is being projected from
the computer, press the [Auto] button on
either the remote control or the
projector's control panel.
The screen will appear black while the
adjustment is being made.
Sync+
Tracking -
Auto
Tracking +
Keystone
Shift
Sync-
Resize
Projector
Remote control
• While a menu or help screen is being displayed, the [Auto] button on the projector's control
panel can be used to select and accept menu items. In such cases, press the [Auto] button of
the remote control, or exit the menu or help screen before using the [Auto] button on the
projector's control panel.
• If you use the remote control to activate the automatic adjustment function while the E-Zoom, A/
V Mute or P in P functions are in use, the functions being used will be cancelled before
automatic adjustment is carried out. If the [Auto] button on the projector’s control panel is
pressed, automatic adjustment will not be carried out if the E-Zoom or P in P function is being
used.
• Automatic adjustment may not work properly with some types of signals which are output by
computers. In such cases, you may need to adjust the tracking and sync manually.
Adjusting the tracking
I
If vertical stripes appear in the projected images, and this cannot be fixed
using automatic adjustment, you will need to adjust the tracking manually
using the following procedure.
Procedure
Sync+
Tracking -
Auto
Tracking +
While holding down the [Shift] button on
the projector's control panel, press the
[Tracking +] button.
The tracking value increases each time the button
is pressed.
Keystone
Shift
Sync-
Projector
Sync+
Tracking -
Auto
Tracking +
While holding down the [Shift] button on
the projector's control panel, press the
[Tracking -] button.
The tracking value decreases each time the button
is pressed.
Keystone
Shift
Sync-
Projector
16
The image will flash when continuous
tracking adjustment is carried out, but this is
normal.
Focusing the Screen Image
Selecting the Image Aspect Ratio
Selecting the Color Mode
Adjusting Computer Images
Adjusting the sync
I
If flickering, fuzziness or interference appear in images that are input from
the computer, and this cannot be fixed using automatic adjustment, you will
need to adjust the sync(synchronization) manually using the following
projection.
Sync+
Tracking -
Auto
Tracking +
While holding down the [Shift] button on
the projector's control panel, press the
[Sync +] button.
The sync value increases each time the button is
pressed.
Basic Operations
Procedure
Keystone
Shift
Sync-
Projector
Sync+
Tracking -
Auto
Tracking +
While holding down the [Shift] button on
the projector's control panel, press the
[Sync -] button.
The sync value decreases each time the button is
pressed.
Keystone
Shift
Sync-
Projector
• If you do not adjust the tracking
first and then adjust the sync, it will not be possible to get the
best adjustment results. Incorrect tracking adjustment may not be noticeable with some types of
picture. However, pictures with lots of lines and shading will tend to show incorrect tracking
adjustments more clearly, so be sure to check the tracking adjustment first.
• It may also be possible to fix flickering and fuzziness by adjusting the brightness, contrast ,
sharpness and keystone correction settings.
17
Adjusting the Volume
Yo can adjust the volume of the sound coming from the projector's built-in speaker.
Procedure
Press the [Volume
,
] button on the
projector's control panel or the
[Volume -,+] button on the remote control.
If you press the [
] or [+] side, the volume
increases, and if you press the [
] side or [-]
side, the volume decreases. While the volume is
being changed, the volume value appears in the
volume gauge.
Keystone
Shift
Sync-
Resize
A/V Mute
Volume
Projector
18
Remote control
Settings and Useful
Functions
This chapter describes the environment setting menus and
useful functions that can be used when a computer is
connected.
Environment Setting Menu Functions and
Operations ......................................................20
•
Video Menu ........................................................................ 20
• Video..................................................................................................20
• Computer ...........................................................................................22
•
Audio Menu........................................................................ 23
•
Setting Menu ...................................................................... 23
•
User's Logo Menu.............................................................. 24
•
Advanced Menu ................................................................. 25
•
About Menu.......................................................................... 26
• Composite Video, S-Video.................................................................26
• Component Video, Computer ............................................................26
•
Reset All Menu................................................................... 27
•
Using the Menus ................................................................ 28
Useful Functions When a Computer is
Connected ......................................................30
•
A/V Mute ............................................................................ 30
•
Freeze.................................................................................. 30
•
E-Zoom ............................................................................... 31
•
P in P (Picture in Picture) ................................................. 32
1
Environment Setting Menu Functions and Operations
The setting menus can be used to carry out a variety of settings and adjustments.
The menus have a hierarchical structure, with a main menu that is divided into sub-menus, which are further divided into
other sub-menus.
Main menu
Sub-menu
Video Menu
•
•
The functions in the Video menu cannot be adjusted while no image signal is being input.
The items appearing in the Video menu will vary depending on the input signal that is being projected.
Items in menus other than the menu for the signal currently being input cannot be adjusted.
Video (RGB-Video, YCbCr , YPbPr , S-Video, Video)
RGB-Video
S-Video,Video
20
Component (YCbCr, YPbPr)
Video
Setting Menu
Advanced Menu
Reset All Menu
Audio Menu
User's Logo Menu
About Menu
Using the Menus
Sub-menu
Default
setting
Function
Position
Moves the image display position vertically and horizontally.
button on the projector's control panel or the [Enter] button
• Press the
on the remote control, and make the adjustment using the display position
adjustment screen that appears.
Depends on
connection
Brightness
Adjusts the image brightness.
Median value
(0)
Contrast
Adjusts the difference between light and shade in the images.
Median value
(0)
Color
(Not available for RGB-Video)
Adjusts the color intensity for the images.
Median value
(0)
Tint
(Not available for RGB-Video)
Adjust the image tint.
Can only be adjusted when NTSC signals are being input.
Median value
(0)
Sharpness
Adjusts the image sharpness.
Median value
(0)
Color Mode
Corrects the vividness of the image color.
You can select from five different quality settings depending on the
surroundings.
:Ideal for projecting images with greater modulation and
• Dynamic
intensity.
:Ideal for enjoying presentations such as movies which
• Theatre
have large numbers of dark scenes.
:Ideal for enjoying presentations in a natural atmosphere.
• Natural
:Ideal for use in making images as bright as possible when
• PC
projecting computer images.
:Images conform to the sRGB standard.
• sRGB
Dynamic
Video Signal
(S-Video and Video only)
Sets the video signal format.
button on the projector's control panel or the [Enter] button
• Press the
on the remote control, and select the video signal format from the menu
that appears.
• When set to Auto, the video signal format is set automatically, but if
projecting signals in PAL (60 Hz) format, the setting needs to be made
manually.
Auto
Noise
Reduction
Turns the noise reduction function on and off.
When set to ON , noise is reduced.
Ignored when a menu or help screen is being displayed, even when set to
ON. The setting becomes effective from the point where the menu or help
screen is closed.
OFF
Reset
Resets all adjustment values for the Video menu functions to their default
settings.
button on the projector's control panel or the [Enter] button
• Press the
on the remote control to display the confirmation screen, and select Yes.
• Select Reset All to return all menu settings to their default settings. (p.27)
Settings and Useful Functions
Main menu
Video Menu
* If set to sRGB, the color temperature for the Color Adjustment command in the Advanced menu will be set to 6500K.
21
Environment Setting Menu Functions and Operations
Computer (Analog-RGB, Digital-RGB)
Digital-RGB
Analog-RGB
Main menu
Video
Sub-menu
Default
setting
Function
Position
(Analog-RGB only)
Moves the image display position vertically and horizontally.
button on on the projector's control panel or the [Enter]
• Press the
button on the remote control, and make the adjustment using the display
position adjustment screen that appears.
Depends on
connection
Tracking
(Analog-RGB only)
Adjusts computer images when vertical stripes appear in the images.
Depends on
connection
Sync.
(Analog-RGB only)
0
Adjusts computer images when flickering, fuzziness or interference appear
in the images.
• Flickering and fuzziness may also appear when the brightness, contrast ,
sharpness or keystone settings are adjusted.
• You can obtain the best results if you adjust the tracking first and then
adjust the synchronization.
Brightness
Adjusts the image brightness.
Median value
(0)
Contrast
Adjusts the difference between light and shade in the images.
• If Auto is selected, contrast adjustment is carried out at periodical
intervals.
Auto
Sharpness
Adjusts the image sharpness.
Median value
(0)
Color Mode
Corrects the vividness of the image color. The settings are saved separately PC
for each source.
You can select from five different quality settings depending on the
surroundings.
:Ideal for projecting images with greater modulation and
• Dynamic
intensity.
:Ideal for enjoying presentations such as movies which have
• Theatre
large numbers of dark scenes.
:Ideal for enjoying presentations in a natural atmosphere.
• Natural
:Ideal for use in making images as bright as possible when
• PC
projecting computer images.
:Images conform to the sRGB standard.
• sRGB
Resolution
(Analog-RGB only)
Select Auto or Manual.
• If Auto is selected, automatic setup is carried out.
• If Manual is selected, you can select the image resolution for adjustment
from a list.
Auto
Preset
(Analog-RGB only)
Saves the current input resolution to the preset list.
-
Reset
Resets all adjustment values for the Video menu functions to their default
settings.
button on the projector's control panel or the [Enter] button
• Press the
on the remote control to display the confirmation screen, and select Yes.
• Select Reset All to return all menu settings to their default settings. (p.27)
* If set to sRGB, the color temperature for the Color Adjustment command in the Advanced menu will be set to 6500K.
22
Video Menu
Setting Menu
Advanced Menu
Reset All Menu
Audio Menu
User's Logo Menu
About Menu
Using the Menus
Audio Menu
Audio
Default
setting
Sub-menu
Function
Audio Input
Sets the audio input port from Audio1, Audio2 or USB to match the current
video source.
Depends on
connection
Volume
Adjusts the volume.
15
Treble
Adjusts the treble setting.
Median value
(0)
Bass
Adjusts the bass setting.
Median value
(0)
Reset
Resets all adjustment values for the Audio menu functions to their default
settings.
button on the projector's control panel or the [Enter] button
• Press the
on the remote control to display the confirmation screen, and select Yes.
• Select Reset All to return all menu settings to their default settings. (p.27)
Settings and Useful Functions
Main menu
Setting Menu
Main menu
Setting
Sub-menu
V-Keystone
Function
Corrects vertical keystone distortion in images.
• When keystone correction is carried out, the projected image will become
smaller.
• If using both horizontal and vertical keystone correction, first make the
vertical correction and then make the horizontal correction in that order.
• The keystone correction settings are memorized, so that if you change the
position or angle of the projector, you may need to readjust the keystone
correction settings.
• If the images become uneven in appearance after keystone correction is
carried out, decrease the sharpness setting.
• If you carry out both horizontal and vertical keystone correction, the
correction range will become smaller than it would be if only one type of
correction was carried out.
Default
setting
Median value
(0)
23
Environment Setting Menu Functions and Operations
Main menu
Setting
Sub-menu
Default
setting
Function
H-Keystone
Corrects horizontal keystone distortion in images.
• When keystone correction is carried out, the image becomes smaller.
• If using both horizontal and vertical keystone correction, first make the
vertical correction and then make the horizontal correction in that order.
• The keystone correction settings are memorized, so that if you change the
position or angle of the projector, you may need to readjust the keystone
correction settings.
• If the images become uneven in appearance after keystone correction is
carried out, decrease the sharpness setting.
• If you carry out both horizontal and vertical keystone correction, the
correction range will become smaller than it would be if only one type of
correction was carried out.
Median value
(0)
P in P
Sets the input source for the sub-screen of the Picture in Picture function to
either Composite Video or S-Video.
• The Picture in Picture function can be used by pressing the [P in P]
button. (p.32)
Composite
No-Signal
Msg.
Sets the message status and background color at times such as when no
image signal is being input.
• To change the user's logo, you need to record and set your own logo.
(p.51)
Blue
Prompt
Sets whether the source prompt for the input image is displayed on the
screen or not.
ON
A/V Mute
Sets the screen status when the [A/V Mute] button is pressed.
• To change the user's logo, you need to record and set your own logo.
Black
Comp1 Input
Sets the image signal for Computer 1 input.
Digital-RGB/
Analog-RGB
Comp2/
YCbCr
Input
Sets the image signal for Computer 2 input.
YCbCr
Sleep Mode
Sets the energy saving operation when no image signal is being input.
• When set to ON, projection stops automatically and the projector changes
to sleep mode if no operations are carried out for 30 minutes while the
"No-Signal." message is being displayed. (The
indicator lights
orange.)
• Projection starts again when the [Power] button is pressed.
ON
Reset
Returns the adjustment values for the Setting menu to their default settings. button on the projector's control panel or the [Enter] button
• Press the
on the remote control to display the confirmation screen, and select Yes.
• Select Reset All to return all menu settings to their default settings. (p.27)
User's Logo Menu
Main menu
User's Logo
24
Sub-menu
Execute
Function
Records a user's logo. (p.51)
button on the projector's control panel or the [Enter] button
• Press the
on the remote control, and follow the operations given in the screen that
appears.
Default
setting
EPSON logo
Video Menu
Setting Menu
Advanced Menu
Reset All Menu
Audio Menu
User's Logo Menu
About Menu
Using the Menus
Advanced Menu
Advanced
Sub-menu
Default
setting
Function
Language
Sets the language for message displays.
button on the projector's control panel or the [Enter] button
• Press the
on the remote control, and select the language from the selection menu
that appears.
English
Startup
Screen
Sets whether the startup screen is displayed or not.
• To change the user's logo, you need to record and set your own logo.
ON
Color
Adjustment
Adjusts the color temperature and intensity of each RGB color in the
Color Temp :
image.
Depends on
Absolute color temperature: Lighter colors are adjusted so that they range
connection
from having a red tinge to having a blue tinge. When the color temperature
is lower, the red content is greater and color tones appear softer. When the
color temperature is higher, the blue content is greater and color tones
appear fresher.
button on the projector's control panel or the [Enter] button
• Press the
on the remote control, and make the setting using the color temperature
menu that appears.
RGB: Sets the intensity of each color (red, green and blue).
button on the projector's control panel or the [Enter] button
• Press the
on the remote control, select R (red), G (green) or B (blue) from the color
definition menu that appears, and then make the adjustment.
• You can adjust the colors while viewing the results on the screen.
(This item cannot be selected if sRGB has been selected as the Color Mode
setting in the Video menu.)
Rear Proj.
Use when projecting images from behind a translucent screen.
When set to ON, the projected images are horizontally reversed.
OFF
Ceiling
Use when installing the projector to a ceiling or when using the projector
upside down.
When set to ON, the projected images are horizontally and vertically
reversed.
OFF
COM Port
Switches between Control (RS-232C) and USB serial communication.
RS-232C
Reset
Resets all adjustment values for the Advanced menu functions to their
default settings.
button on the projector's control panel or the [Enter] button
• Press the
on the remote control to display the confirmation screen, and select Yes.
• Select Reset All to return all menu settings to their default settings. (p.27)
Settings and Useful Functions
Main menu
25
Environment Setting Menu Functions and Operations
About Menu
•
•
The About menu shows the status of the current image source.
The Lamp item appears as 0H for 0 – 10 hours, after that, it appears in units of 1 hour.
Composite Video , S-Video
Main menu
About
Sub-menu
Default
setting
Function
Lamp
Displays the cumulative lamp operating time.
0H
• When the lamp warning period is reached, the display characters appear in
red.
Reset Lamp
Timer
Initializes the lamp operating time. When this command is selected, the
cumulative lamp operating time is reset to the initial default value. (p.49)
-
Video Source Displays the input source which is currently being projected.
Video Signal
Displays the video signal format.
Auto
Component Video , Computer
Main menu
About
26
Sub-menu
Default
setting
Function
Lamp
Displays the cumulative lamp operating time.
0H
• When the lamp warning period is reached, the display characters appear in
red.
Reset Lamp
Timer
Initializes the lamp operating time. When this command is selected, the
cumulative lamp operating time is reset to the initial default value. (p.49)
-
Video Source Displays the input source which is currently being projected.
-
Input Signal
Displays the input signal settings.
-
Frequency
Shows the horizontal and vertical scanning frequencies.
-
SYNC
Polarity
Displays the sync(synchronization)
-
SYNC Mode
Displays the sync attributes.
-
Resolution
Displays the input resolution.
-
Refresh
Rate
Displays the refresh rate.
-
polarity.
Video Menu
Setting Menu
Advanced Menu
Reset All Menu
Audio Menu
User's Logo Menu
About Menu
Using the Menus
Reset All Menu
Reset All
Sub-menu
Execute
Default
setting
Function
Resets all items in all environment setting menus to their default settings.
button on the projector's control panel or the [Enter] button
• Press the
on the remote control to display the confirmation screen, and select Yes.
• Select Reset in an individual menu to reset only the settings for the items
in each sub-menu.
• The User's Logo, Lamp and Language settings will not return to their
default settings.
-
Settings and Useful Functions
Main menu
27
Environment Setting Menu Functions and Operations
Using the Menus
The menus can be operated using either the remote control or the projector's control panel.
Procedure
1
Computer/YCbCr
Video
Source
Menu
Esc
Sync+
Tracking -
Tracking +
Auto
Keystone
Shift
Sync-
Resize
2
Projector
Remote control
Main menu
Sub-menu
Select a menu item.
If using the projector's control panel, press the
or
button.
If using the remote control, press the top or
bottom of the [Enter] button.
Source
Menu
Esc
Sync+
Tracking -
Auto
Tracking +
Keystone
Shift
Press the [Menu] button on either the
remote control or the projector's control
panel.
The environment setting menu appears.
The environment setting menu consists of a main
menu and sub-menus. The sub-menu that
corresponds to the currently-selected item in the
main menu (displayed in yellow) appears.
Sync-
Resize
Projector
3
Remote control
Confirm the selection.
Press the
button on the projector's control
panel or the [Enter] button on the remote control
to accept a selection.
The sub-menu that corresponds to the currentlyselected item in the main menu appears.
Source
Menu
Esc
Sync+
Tracking -
Auto
Tracking +
Keystone
Shift
Sync-
Resize
Projector
4
28
Remote control
Select the setting item in the sub-menu.
If using the projector's control panel, press the
or
button.
If using the remote control, press the top or
bottom of the [Enter] button.
The commands appearing in the Video menu and
About menu will vary depending on the input
signal that is being projected.
Video Menu
Setting Menu
Advanced Menu
Reset All Menu
Audio Menu
User's Logo Menu
About Menu
Using the Menus
5
-
+
Select a setting value.
If using the projector's control panel, press the
or
button.
If using the remote control, press the left or right
edge of the [Enter] button.
• If a setting is executed or a sub-menu
item continues to another level, "
Execute" or "
Select" appears after
the item name. In such cases, press the
button the projector's control panel or
the [Enter] button on the remote control to
select a setting value in the displayed
menu.
• Refer to list of functions for details on the
functions of each menu item. (p.20)
6
Computer/YCbCr
Close the menu.
Press the [Menu] button on either the projector's
control panel or the remote control.
Video
Source
Menu
Esc
Sync+
Tracking -
Auto
Settings and Useful Functions
7
Select other menu items in the same
way.
Repeat steps 2 to 5 to change the setting for other
menu items. To return to a previous menu, press
the [Esc] button.
Tracking +
Keystone
Shift
Sync-
Resize
Projector
Remote control
29
Useful Functions When a Computer is Connected
This section describes some of the useful functions that can be used when a computer is connected to the projector.
A/V Mute
This function momentarily pauses the image and sound.
For example, it can be used when you do not want to show viewers details of operations such as selecting
different files while computer images are being projected.
However, if you use this function when projecting moving images, the images and sound will still continue to
be played back by the source, and you cannot return to the point where the mute function was activated.
Procedure
Press the [A/V Mute] button on either the
remote control or the projector's control
panel.
The image and sound will then be paused.
Keystone
Shift
Sync-
Resize
A/V Mute
Volume
Projector
Black
Remote control
Blue
Press the [A/V Mute] button on either the remote
control or the projector's control panel to
continue normal projection.
User's logo
You can use the A/V Mute function in the
Setting menu to set the screen appearance
when the images and sound have been
paused to any one of the following three
settings.
Default setting
The default user's logo is the EPSON logo. You can change the user's logo by recording and
setting your own logo. (p.51)
Freeze
This function pauses only the projected images. The sound keeps playing without pausing.
Furthermore, for moving pictures, the playback signal continues to be input even while the picture is paused,
so playback will not resume from the point from where it was paused.
Press the [Freeze] button on the remote
control.
The images will then be paused.
Procedure
Remote control
To continue projecting the images, either press
the [Freeze] button again or press the [Esc]
button.
• When the [Freeze] button is pressed, the menu or help message disappears.
• If you press the [Freeze] button while using the E-Zoom function or after a P in P sub-screen
has been set, all of the screen displays will be paused.
30
A/V Mute
E-Zoom
Freeze
P in P
E-Zoom
This function lets you enlarge or reduce selected areas of images.
Procedure
1
Press the [E-Zoom] button on the remote
control.
A cursor (cross) indicating the center point for the
area to be enlarged will appear on the screen.
Remote control
cross
3
Reduction
Expansion
Move the cross to the area of the image
that is to be enlarged or reduced.
Tilt the [Enter] button on the remote control to
move the cross.
If you press the right side of the [EZoom] button, the image will be
enlarged centering around the cross. If
you press the left side of the [E-Zoom]
button, the area of the image that was
enlarged will then be reduced in size
again.
You can scroll around the image by tilting the
[Enter] button.
Settings and Useful Functions
2
To cancel the zoom, press the [Esc] button.
Shows enlargement ratio
• The selected area can be enlarged to between 1 – 4 times, in 25 steps of x 0.125.
• If a sub-screen has been set using the P in P function, the enlargement function is applied to
both the main screen and the sub-screen.
• If the E-Zoom function is in use, the projector's buttons cannot be used to perform adjustments
such as keystone correction, tracking adjustment and sync adjustment.
• If the E-Zoom function is used while the keystone correction amount is near the limit value, the
keystone correction amount may change.
31
Useful functions when a computer is connected
P in P (Picture in Picture)
This function lets you project computer images or component video images in the main screen, and a video
image (Video or S-Video) in a sub-screen.
The video image in the sub-screen can be set using the P in P command in the Setting menu. (p.24)
• The P in P function cannot be used if the refresh rate for the computer images is set to
interlaced.
• The P in P function cannot be used when TV (525i) component video images are being
projected.
Procedure
1
Connect all components, set the type of
sub-screen using the Setting menu, and
then press the [P in P] button on the
remote control.
The sub-screen will appear at the top-right of the
screen, and the operation guide will appear at the
bottom-left of the screen.
2
Tilt the [Enter] button on the remote
control to change the position of the subscreen.
3
Press the [E-Zoom] button on the
remote control to change the size of the
sub-screen.
• The size of the sub-screen can be changed to one of five different sizes. The following
values are the ratios for the vertical and horizontal lengths of the sub-screens to those of
the main screen when the lengths of the main screen sides are 1.
Size 1
Approx. 1/3.2
Size 2
Approx. 1/2.8
Size 3
Approx. 1/2.5
Size 4
Approx. 1/2.3
• When the [P in P] button is pressed, the initial sub-screen appears in size 2.
32
Size 5
Approx. 1/2.1
4
A/V Mute
E-Zoom
Freeze
P in P
Press the [Enter] button on the remote
control to accept the display position
and size for the sub-screen.
If you press the [P in P] button once more, the
sub-screen will disappear.
Remote control
• If you change and set the position of the sub-screen, the sub-screen will appear in the last
position which was set using the P in P function.
• The E-Zoom function can be used at the same time that the P in P function is being used.
• If the audio input ports for the main screen and sub-screen are preset using the Audio Input
Settings and Useful Functions
command in the Audio menu, you can change the selected audio source by pressing buttons [1]
or [2] on the remote control.
Button [1]: Main screen audio
Button [2]: Sub-screen audio
(Buttons [3] to [5] do not work at this time.)
• If the P in P function is used while the keystone correction amount is near the limit value, the
keystone correction amount may change.
33
Troubleshooting
This chapter describes troubleshooting procedures for the
projector.
Using the Help ..................................................36
When Having Some Trouble ............................ 37
When the Indicators Provide No Help ............39
3
Using the Help
If a problem occurs with the projector, the Help function uses on-screen displays to assist you in solving the problem. It
uses a series of menus in a question and answer format. The questions vary depending on the type of image source.
Procedure
1
Power
Press the [Help] button on either the
remote control or the projector's
control panel.
The Help menu will be displayed.
Help
Computer/YCbCr
Video
Source
Menu
Esc
Sync+
Projector
2
Remote control
Select a menu item.
If using the projector's control panel, the
and
buttons function as the up and down keys.
If using the remote control, press the top or
bottom of the [Enter] button.
Source
Menu
Esc
Sync+
Tracking -
Auto
Tracking +
Keystone
Shift
Sync-
Resize
Projector
3
Remote control
Confirm the selection.
Press the
button on the projector's control
panel or the [Enter] button on the remote control
to accept a selection.
The sub-menu appears.
Source
Menu
Esc
Sync+
Tracking -
Auto
Tracking +
Keystone
Shift
Sync-
Resize
Projector
4
Remote control
Repeat the operations in steps 2 and 3
to proceed through the menu to more
detailed items.
To return to the previous menu, press the [Esc]
button on either the remote control or the
projector's control panel.
You can exit the Help menu at any time by
pressing the [Help] button on either the
projector's control panel or the remote control.
If the Help function does not provide a
solution to the problem, refer to "When
Having Some Trouble" (p.37) or "When the
Indicators Provide No Help" (p.39).
36
When Having Some Trouble
If you are having a problem with the projector, first check the projector's indicators.
The projector is provided with the following three indicators. These indicators alert you to problems with projector
operation.
Operation indicator
Lamp indicator
Temperature indicator
The following tables show what the indicators mean and how to remedy problems that they indicate.
Indicator status
Projector status
: flashing
Problem and remedy
: off
Reference
page
Red Red
Red
Internal problem
Stop using the projector, disconnect the power cord from the
electrical outlet, and contact your dealer or the nearest address
provided at “International Warranty Conditions” in Safety
Instructions/ World-Wide Warranty Terms included in the
package.
Red
Red
Fan problem/Sensor
problem
Stop using the projector, disconnect the power cord from the
electrical outlet, and contact your dealer or the nearest address
provided at “International Warranty Conditions” in Safety
Instructions/ World-Wide Warranty Terms included in the
package.
Red Red
Lamp problem
Replace the lamp with a new one.
When replacing the lamp, check that the lamp and the lamp cover
are securely installed. If the lamp or lamp cover is not securely
installed, the lamp will not turn on.
p.48
Red Red
Lamp operating
error
If the power cord plug is disconnected before the cool-down
had not completely finished before, this may happen the next
time you try to turn on the lamp.
Wait for about 2 minutes without operating the projector. After
about 2 minutes, the cooling fan will stop. When the cooling fan
stops, disconnect the power plug and then re-insert it. When the
power cord is plugged back in, the projector will return to its
previous state, so press the [Power] button on either the remote
control or the projector's control panel to turn it back on.
If the lamp operating error happens again when the power is
turned back on, remove the lamp and check if the lamp is broken.
If it is not broken, reinstall it. If it is broken, replace it. Then
press the [Power] button on either the remote control or the
projector's control panel.
If the indicators still show a problem, stop using the projector,
disconnect the power cord from the electrical outlet, and contact
your dealer or the nearest address provided at “International
Warranty Conditions” in Safety Instructions/ World-Wide
Warranty Terms included in the package.
p.48
Troubleshooting
: lit
37
When Having Some Trouble
Indicator status
Red
Red
Orange
Red
Orange
Projector status
High temperature
inside projector
(overheating)
High-speed cooling
in progress
Lamp will soon need
to be replaced.
Problem and remedy
The lamp will turn off automatically and projection will stop.
Wait for about 5 minutes without operating the projector. After 5
minutes have elapsed, the projector’s cooling fan will stop. Once
the cooling fan has stopped, unplug the power cord and then plug
it back in again.
If the projector overheats, check the following two points.
• Is the setting-up location well ventilated?
Check that the air inlet and air outlet are clear, and that the
projector is not positioned against a wall.
• Is the air filter blocked with dust?
If the air filter is dirty, it should be cleaned.
When the power cord is plugged back in, the projector will return
to its previous state, so press the [Power] button on either the
remote control or the projector's control panel to turn it back on.
If the projector continues to overheat even after the above points
have been checked, or if the indicators show a problem when the
power is turned back on, stop using the projector, disconnect the
power cord from the electrical outlet, and contact your dealer or
the nearest address provided at “International Warranty
Conditions” in Safety Instructions/ World-Wide Warranty Terms
included in the package.
(This is not an abnormality, but if the temperature rises too high
again, projection will stop automatically.)
• Set the projector up in a place which is well-ventilated, and so
that the air inlet and exhaust vents are clear.
• Clean the air filter.
(No abnormality)
Have a new replacement lamp ready.
The lamp service life can become shorter than normal as a result
of the usage conditions, and so the lamp should be replaced as
soon as possible.
Reference
page
Setup Guide
p.46
Setup Guide
p.46
p.47
* The appearance of the
indicator at this time will vary
depending on the status of the projector.
Orange
Green
Standby condition
(No abnormality)
Projection starts when the [Power] button is pressed.
p.6
Warm-up in progress
(No abnormality)
Wait for a short while. The
light with a green color.
p.7
indicator will stop flashing and
Green
Projecting in
progress
(No abnormality)
p.7
Orange
Cool-down in
progress
(No abnormality)
• Wait for a short while.
The cool-down (lamp cooling operation) period lasts for
about 2 minutes. The actual time will vary depending on the
external air temperature.
• The [Power] button will not operate during the cool-down
period. When cool-down is complete, the
indicator will stop
flashing and light orange. You can then use the [Power] button.
p.9
• If the projector is not operating properly even though the indicators are all showing normal, refer
to "When the Indicators Provide No Help" on the following page.
• If an indicator is showing a status which does not appear in the previous tables, contact your
dealer or the nearest address provided at “International Warranty Conditions” in Safety
Instructions/ World-Wide Warranty Terms included in the package.
38
When the Indicators Provide No Help
If any of the following problems occur and the indicators do not offer a solution, refer to the pages given for each
problem.
No images appear
p.39, 40
Images appear dark
p.42
Poor image quality
p.40
Images appear green
p.43
Only part of the image is displayed
p.41
No sound can be heard
p.43
(Large/small)
The remote control does not work p.44
The image colors are not right
p.42
The power does not turn off
p.44
Condition
No images appear (Nothing at all appears)
Remedy
Is the lens cover still attached?
Remove the lens cover. (p.6)
Is the power cord disconnected?
Check the power cord connection at the power inlet of
the projector and at the wall outlet. (p.6)
Was the power turned off and then straight
back on again?
Wait until cool-down has finished. You can then use the
[Power] button on either the remote control or the
projector's control panel. (p.9)
While the
indicator is flashing orange (during cooldown ), the [Power] button on either the remote
control or the projector's control panel will not operate.
Have you pressed the [Power] button on
either the remote control or the projector's
control panel?
Press the [Power] button on either the remote control or
the projector's control panel. (p.7)
Is sleep mode active?
Turn the projector power back on. To cancel the sleep
mode setting, set Sleep Mode in the Setting
environment setting menu to OFF.
Setting - Sleep Mode (p.24)
When sleep mode has been set to ON, the lamp turns
off automatically if no operations are carried out for 30
minutes while no video signal is being input.
The
indicator lights orange at this time.
Has the image brightness been adjusted
correctly?
Adjust using the Brightness environment setting menu.
Video - Brightness (p.21, 22)
Is A/V Mute mode active?
Press the [A/V Mute] button on either the remote
control or the projector's control panel to cancel the
A/V Mute mode.
(p.30)
Is the projected image completely black?
Cancel the screen saver, or re-check the images being
input.
Some input images, such as screen savers, may be
completely black.
Is an image signal being input?
If No-Signal Msg. in the Setting menu has been set to
OFF, no messages will be displayed.
Change the No-Signal Msg. setting to Black or Blue for
messages to be displayed.
Setting - No-Signal Msg. (p.24)
If a message is displayed, refer to the item indicated.
Try resetting all of the current settings.
Reset All - Execute (p.27)
Troubleshooting
Probable cause
39
When the Indicators Provide No Help
Condition
No images appear (Messages do appear)
“Not Supported.” message appears on the screen.
“No-Signal.”message appears on the screen.
Probable cause
Remedy
Does the input signal setting match the
connected source?
Use the Comp1 Input or Comp2/YCbCr Input
commands in the Setting menu to select the signal
format that matches the connected source.
For Comp1
:Digital-RGB, Analog-RGB,
RGB-Video
For Comp2/YCbCr :Analog-RGB, RGB-Video,
YCbCr , YPbPr
(p.24)
Is the connection port for the input source
selected correctly?
Press the [Computer/YCbCr] or [Video] button on the
projector's control panel or the [Comp1], [Comp2/
YCbCr], [Video] or [S-Video] button on the remote
control to change the image source. (p.7)
Is the power for the computer or video source
turned on?
Turn on the power. (p.7)
Check the mode which corresponds to the
frequency of the image signals being output
from the computer.
Refer to the documentation provided with your
computer for details on changing the resolution and
frequency of the image signals being output from the
computer. (p.55)
If a laptop computer or a computer with a
LCD screen has been connected to the
projector, it is necessary to output the image
signals to the projector rather than to the
screen.
Normally image signals are output to only the
computer's LCD screen, so you need to change the
output to an external destination. For some computer
models, when the image signals are output externally,
they no longer appear on the LCD screen. For details,
refer to the section of the documentation provided with
your computer under a heading such as "External
output", "Connecting an external monitor" or similar.
(p.8)
Condition
Poor image quality
• The image is fuzzy
• Part of the image is out of focus
• The whole image is out of focus
• The image is distorted
• The image contains interference
Probable cause
Remedy
Has the focus been adjusted correctly?
Adjust the focus. (p.14)
Has the front adjustable foot been adjusted
so that the projection angle is too big?
Adjust the projection angle. (p.11)
If the projection angle is too big, the image will be out
of focus vertically.
40
Is the projector at the correct distance?
The recommended distance from the projector to the
screen is within 0.9 - 12.4 m (3.0 - 40.7 ft.). Set up the
projector so that the projection distance is within this
range. (Setup Guide)
Is the projector beam perpendicular to the
screen?
Adjust the projection angle so that the projector beam
is perpendicular to the screen. (p.11)
Probable cause
Remedy
Is the lens dirty?
Clean the lens. (p.46)
Has condensation formed on the lens?
Turn off the power and wait for the condensation to
disappear.
If the projector is suddenly taken from a cold
environment to a warm environment, condensation may
form on the lens, and this may cause the images to
appear fuzzy.
Does the signal format setting match the
format of the input signal?
Use the Video Signal command in the Video menu to
select the video signal format. The projector may not
be able to automatically identify some types of video
signal that are input. (p.21)
Does the input signal setting match the
connected source?
Use the Comp1 Input or Comp2/YCbCr Input
commands in the Setting menu to select the signal
format that matches the connected source.
For Comp1
:Digital-RGB, Analog-RGB,
RGB-Video
For Comp2/YCbCr :Analog-RGB, RGB-Video,
YCbCr , YPbPr
(p.24)
Are the cables connected correctly?
Check that all cables that are required for projection are
connected correctly. (Setup Guide)
Is an extension cable being used?
Connect an amplifier and check.
If an extension cable is used, electrical interference
may increase.
Have the sync(synchronization) , tracking
and display position been adjusted correctly?
(When connected to a computer)
Press the [Auto] button on either the remote control or
the projector's control panel to adjust these settings.
You can also use the environment setting menus to
make the adjustment. (p.16, 22)
Has the correct resolution been selected?
(When connected to a computer)
Set the computer so that the signals that are output are
compatible with this projector. Refer to the
documentation provided with your computer for details
on changing the settings. (p.55)
Condition
Probable cause
The aspect ratio
correctly.
may not be selected
Troubleshooting
• Image is too large (Only part of the image is displayed)
• Image is too small
Remedy
Press the [Resize] button. (p.15)
Has the Position setting been adjusted
correctly?
Use the Position command in the Video menu to adjust.
(p.21, 22)
Has the correct resolution been selected?
(When connected to a computer)
Set the computer so that the signals that are output are
compatible with this projector. Refer to the
documentation provided with your computer for details
on changing the settings. (p.55)
Change the resolution for the laptop
computer or computer with a LCD screen.
(When connected to a computer)
Change the resolution so that the image is displayed in
the whole of the projection area, or set the video signal
to external output only. (p.8, 11)
41
When the Indicators Provide No Help
Probable cause
Remedy
Has the computer been set for dual display?
(When connected to a computer)
If dual display has been activated in the Display
Properties of the computer's Control Panel, the
projector will only project about half of the image on
the computer screen. To display the whole of the image
on the computer screen, turn off the dual display
setting. Refer to the video driver manual for the
computer's monitor for further details.
Condition
The image colors are not right
Probable cause
Remedy
Has the image brightness been adjusted
correctly?
Adjust using the Brightness environment setting menu.
Video - Brightness (p.21, 22)
Are the cables connected correctly?
Check that all cables that are required for projection are
connected correctly. (Setup Guide)
Has the image contrast
correctly?
Adjust using the Contrast environment setting menu.
Video - Contrast (p.21, 22)
been adjusted
Has the color been adjusted correctly?
Use the Color Adjustment command in the Advanced
menu to adjust the contrast.
Advanced - Color Adjustment (p.25)
Have the color intensity and tint been
adjusted correctly?
Use the Video menu to adjust the Color and Tint
settings
Video - Color, Tint (p.21)
(The colors may not exactly match the colors in the
image on the computer screen or LCD screen, but this
is normal and is not the sign of a problem.)
Is the lamp due for replacement?
Replace the lamp with a new one. (p.47, 48)
If the
indicator is flashing orange, it means that the
lamp will soon be due for replacement. When the lamp
is nearly due for replacement, the image will become
darker and the tint will become poorer.
Does the input signal setting match the
connected source?
Use the Comp1 Input or Comp2/YCbCr Input
commands in the Setting menu to select the signal
format that matches the connected source.
For Comp1
:Digital-RGB, Analog-RGB,
RGB-Video
For Comp2/YCbCr :Analog-RGB, RGB-Video,
YCbCr , YPbPr
(p.24)
Condition
Images appear dark
42
Probable cause
Remedy
Is the lamp due for replacement?
Replace the lamp with a new one. (p.47, 48)
If the
indicator is flashing orange, it means that the
lamp will soon be due for replacement. When the lamp
is nearly due for replacement, the image will become
darker and the tint will become poorer.
Has the image brightness been adjusted
correctly?
Adjust using the Brightness environment setting menu.
Video - Brightness (p.21, 22)
Has the image contrast
correctly?
Adjust using the Contrast environment setting menu.
Video - Contrast (p.21, 22)
been adjusted
Condition
Images appear green
Probable cause
Remedy
Do the settings for component video input
signals match the signals from the connected
device?
Use the Comp2/YCbCr Input commands in the Setting
menu to select the signal format that matches the
connected source.
Setting - Comp2/YCbCr Input (p.24)
If the YCbCr or YPbPr settings are incorrect, the
images may appear greenish.
Condition
No sound can be heard
Remedy
Is the audio source connected correctly?
Check that the cable being used matches the input port.
(Setup Guide)
Has the correct audio input port been
selected?
Use the Audio Input command in the Audio menu to
set the port for audio signal input. (p.23)
Is sound being output from the audio source?
Check the volume for the audio source.
Has the volume been adjusted to the
minimum setting?
Adjust the volume so that the sound is audible. (p.18)
Has the A/V Mute function been turned on?
The projector may be in A/V Mute mode. Press the [A/
V Mute] button on the projector’s control panel or the
remote control to cancel the A/V Mute mode. (p.30)
Have the correct USB audio settings for this
projector been made at the computer?
(When connected to a computer)
If using a USB cable to output sound from the
computer, you need to select USB audio for the
projector in the audio properties for the computer.
Troubleshooting
Probable cause
43
When the Indicators Provide No Help
Condition
The remote control does not work
Probable cause
Remedy
Is the R/C switch on the remote control set to
OFF?
Set the R/C switch on the remote control to ON.
(p.7)
Is the remote control being pointed at the
right angle?
The operating angle for the remote control is
approximately 30° horizontally and approximately 15°
vertically. Use the remote control within these ranges.
(Setup Guide)
Is the remote control too far from the
projector?
The operating distance for the remote control is
approximately 10 m (30 ft.). Use the remote control
within this distance. (Setup Guide)
Is the remote control being pointed at the
projector when a remote control receiver has
been connected?
If the remote control receiver is connected, point the
remote control toward the remote control receiver
instead of toward the projector.
Is direct sunlight or strong light from
fluorescent lamps shining onto the remote
control light-receiving area ?
Avoid using projector in places where the remote
control light-receiving area is exposed to strong light.
Are there batteries in the remote control?
Insert batteries into the remote control. (Setup Guide)
Are the batteries dead?
Replace the batteries with new ones. (Setup Guide)
Have the batteries been inserted correctly?
Insert the batteries so that they face in the correct
direction. (Setup Guide)
Condition
The power does not turn off (after the [Power] button is
pressed)
Probable cause
Is the
indicator still orange?
This projector is designed so that the
indicator
remains lit even when after the power has been turned
off.
Is the fan still operating?
After the [Power] button on either the remote control or
the projector's control panel is pressed to turn off the
power, the cool-down period starts.
44
Remedy
The
indicator will switch off when the power cord
is disconnected from the electrical outlet.
After the cool-down period is complete,
the
indicator changes to a steady orange, and you
can then turn off the power switch at the rear of the
projector.
* The cool-down period lasts for about 2 minutes. The
actual time will vary depending on factors such as
the ambient air temperature.
Appendices
This chapter provides information on maintenance
procedures to ensure the best level of performance for the
projector for a long time.
Maintenance .....................................................46
•
Cleaning.............................................................................. 46
• Cleaning the Projector Case...............................................................46
• Cleaning the Lens ..............................................................................46
• Cleaning the Air Filter .......................................................................46
•
Replacing Consumables .................................................... 47
•
•
•
•
Lamp Replacement Period.................................................................47
Replacing the Lamp ...........................................................................48
Resetting the Lamp Operating Time..................................................49
Replacing the Air Filter .....................................................................50
Saving a User's Logo.......................................51
Optional Accessories ......................................53
List of Supported Signal Resolutions ............54
•
Component Video Input/ RGB Video Input ................... 54
•
Composite Video/ S-Video Input...................................... 54
•
Computer ........................................................................... 55
Specifications................................................... 56
Appearance ......................................................58
Part Names and Functions..............................59
•
Front/ Top........................................................................... 59
•
Control Panel ..................................................................... 60
•
Rear..................................................................................... 61
•
Base ..................................................................................... 61
•
Remote Control.................................................................. 62
• Underneath cover ...............................................................................62
Glossary............................................................63
Index..................................................................65
4
Maintenance
This section describes maintenance tasks such as cleaning the projector and replacing consumable parts.
Cleaning
You should clean the projector if it becomes dirty or if the quality of projected images starts to deteriorate.
Be sure to read the separate Safety Instructions/ World-Wide Warranty Terms for
details on safe handling of the projector during cleaning.
Cleaning the Projector Case
Clean the projector case by wiping it gently with a soft cloth.
If the projector is particularly dirty, moisten the cloth with water containing a small amount of neutral
detergent, and then firmly wring the cloth dry before using it to wipe the projector case. Then wipe the case
again with a soft, dry cloth.
Do not use volatile substances such as wax, alcohol or thinner to clean the projector
case. These can cause the case to warp and make the coating finish peel off.
Cleaning the Lens
Use a commercially-available air blower, or use a lens cleaning paper to gently wipe the lens.
Do not rub the lens with harsh materials or subject the lens to shocks, as it can
easily become damaged.
Cleaning the Air Filter
If the air filter becomes clogged with dust, it can cause overheating and damage the projector.
Stand up the projector in order to prevent dust getting inside the projector, and then use a vacuum cleaner to
clean away the dust from the air filter.
• If the air filter is difficult to clean or if it is broken,
it should be replaced. Contact your dealer for a
spare air filter.
• Replacement lamps are provided with a spare
air filter. The air filter should also be replaced
when the lamp is replaced.
46
Cleaning
Replacing Consumables
Replacing Consumables
This section describes how to replace the lamp and the air filter.
Lamp Replacement Period
It is time to replace the lamp when:
•
The message "Lamp Replace" appears on the screen when projection starts.
The message appears for 30 seconds, and disappears again
after 30 seconds have passed.
A message will be displayed.
•
The
indicator flashes orange or lights red.
Lamp indicator flashes orange or lights red.
The projected image gets darker or starts to deteriorate.
• In order to maintain the brightness and quality of the projected images, replace the lamp as
soon as possible after the warning message appears.
• The replacement warning message is set to appear after 2900 hours of lamp use in order to
maintain the brightness and quality of the projected images. If you continue to use the lamp after
this period, the possibility of the lamp breaking becomes greater. When the lamp replacement
message appears, replace the lamp with a new one as soon as possible, even if it is still
working.
• The warning message appears after 2900 hours of use, but the actual life of each individual
lamp will vary depending on the characteristics of the lamp and on the way it has been used.
Some lamps may stop operating before 2900 hours of use, so you should always have a spare
lamp ready in case.
• When the lamp replacement warning message appears, the user's logo will not appear even if
the start-up screen setting is ON.
• Contact your dealer for a spare lamp.
Appendices
•
47
Maintenance
Replacing the Lamp
• If the lamp stops working and needs to be replaced, there is the danger that the lamp may
break when handled.
If replacing the lamp of a projector which has been installed to the ceiling, you should
remove the projector from the ceiling before replacing the lamp. If the projector cannot be
removed from the ceiling, you should always assume that the lamp is broken and handle it
with extreme care during removal. Furthermore, you should stand to the side of the
projector, not underneath it.
• Wait until the lamp has cooled down sufficiently before opening the lamp cover. After the
cool-down period has finished, it takes approximately a further 30 minutes for the lamp to
be cool enough.
Procedure
1
2
3
4
5
48
Turn off the projector power, wait for the
cool-down period to end, and then
disconnect the power cord. (p.9)
The cool-down period lasts for about 2 minutes.
The actual time will vary depending on the
external air temperature.
Wait until the lamp has cooled down,
and then remove the lamp cover.
It takes approximately 30 minutes for the lamp to
cool down by itself. Use the screwdriver that is
provided with the spare lamp to slide the lamp
cover opening switch so that the lamp cover lifts
up. Hold the raised section of the lamp cover and
then slide it forward to remove it from the
projector.
Loosen the two lamp fixing screws.
Use the screwdriver that is supplied with the
spare lamp to loosen the two lamp fixing screws
that are securing the lamp to the projector.
Take out the lamp.
Hold the lamp by the two recesses on the side to
lift it up and out from the projector.
Install the new lamp.
Hold the lamp so that it faces the correct way to
fit into the projector, and then insert the lamp
until it clicks into place and tighten the two fixing
screws.
Cleaning
Replacing Consumables
6
Install the lamp cover.
Insert the two cover tabs into the projector, and
then press the other side of the lamp cover until it
clicks into place.
• Install the lamp securely. If the lamp cover is removed, the lamp turns off automatically as a
safety precaution. Moreover, the lamp will not turn on if the lamp or the lamp cover is not
installed correctly.
• Spare lamps are provided with a spare air filter. The air filter should also be replaced when the
lamp is replaced.
• Dispose of used lamps properly in accordance with your local regulations.
Resetting the Lamp Operating Time
The projector has a built-in counter which keeps track of the lamp operating time. When the cumulative
operating time reaches a certain point, it causes the replacement warning message to be displayed. Therefore,
the counter needs to be reset after the lamp has been replaced with a new one. You can do this using the
projector menu.
Do not reset the lamp operating time except after the lamp has been replaced, otherwise the lamp
replacement period will not be indicated correctly.
Procedure
1
Computer/YCbCr
Press the [Menu] button on either the
remote control or the projector's
control panel.
The environment setting menu will be displayed.
Video
Source
Menu
Esc
Sync+
Tracking -
Auto
Tracking +
Keystone
Shift
Sync-
2
3
Remote control
Select Reset Lamp Timer from the
About menu.
Press the
button on the projector's control
panel or the [Enter] button on the remote control.
Reset the lamp operating time.
Select Yes, and then press the
button on the
projector's control panel or the [Enter] button on
the remote control.
Appendices
Projector
49
Cleaning
Maintenance
Replacing Consumables
Replacing the Air Filter
Procedure
1
2
3
Turn off the projector power, wait for the
cool-down period to end, and then
disconnect the power cord. (p.9)
The cool-down period lasts for about 2 minutes.
The actual time will vary depending on the
external air temperature.
Put your finger into the recess in the air
filter hook, and lift up the air filter to
remove it.
In order to prevent any dust on the air filter from
getting into the projector, be sure to stand up the
projector so that the handle is at the top.
Install the new air filter.
First insert the tabs, and then press down on the
opposite side until it clicks into place.
Dispose of used air filters properly in accordance with your local regulations.
50
Saving a User's Logo
You can record the image that is currently being projected as a user's logo.
When you record a user's logo, any user's logo that has already been recorded will be erased.
Procedure
1
Computer/YCbCr
Project the image that you would like to
use as a user's logo, and then press the
[Menu] button on the projector’s control
panel or the remote control.
Video
Source
Menu
Esc
Sync+
Tracking -
Auto
Tracking +
Projector
2
Remote control
Select the User's Logo menu, and then
button on the projector's
press the
control panel or the [Enter] button on
the remote control.
If keystone correction has been carried out,
it will be cancelled when the User's Logo
menu is selected.
3
4
Select Yes in the sub-menu, and then
press the
button on the projector's
control panel or the [Enter] button on
the remote control.
The image to be recorded and a selection
marquee box will be displayed. Move the
marquee box to select the part of the
image to use.
Tilt the [Enter] button on the remote control to
select the part of the image to use as the user’s
logo, and then press the
button on the
projector's control panel or the [Enter] button on
the remote control.
5
Appendices
If the video signal being input is a YCbCr
or YPbPr signal, the selection marquee
box can only be moved around the middle
of the image.
Select Yes at the confirmation screen,
and then press the
button on the
projector's control panel or the [Enter]
button on the remote control.
51
Saving a User's Logo
6
7
Select the zoom rate in the Zoom rate
setting screen, and then press the
button on the projector's control panel
or the [Enter] button on the remote
control.
Select Yes at the confirmation screen,
and then press the
button on the
projector's control panel or the [Enter]
button on the remote control.
The image will then be saved. Once the image has
been saved, the message "Saving the user's logo is
completed." will be displayed.
• Saving the user's logo may take a few moments (about 40 seconds). Do not use the projector or
any other sources which are connected to the projector while the user's logo is being saved,
otherwise it may result in errors in projector operation.
• User's logos can be saved at up to 400 x 300 dots in size.
• If the image resolution is not XGA , or if a video image is being projected, the display size will
be changed.
52
Optional Accessories
The following optional accessories are available for purchase if required. This list of optional accessories is
current as of February 2002. Details of accessories are subject to change without notice.
Spare lamp
ELPLP17
Digital video cable
ELPKC21
(3 m (9.8 ft.) - for DVI-D/DFP 20-pin)
ELPSC06
DFP cable for connecting the projector to a computer
with a digital RGB output interface.
60-inch screen
ELPSC07
DVI analog cable
ELPKC25
(3 m (9.8 ft.) - for DVI-I/mini D-Sub 15-pin)
80-inch screen
ELPSC08
Use as a replacement for spent lamps.
Portable screen
A compact screen which can be carried easily.
Computer cable
ELPKC02
(1.8 m (6 ft.) - for mini D-Sub 15-pin/mini D-Sub
15-pin)
Computer cable
ELPKC09
(3 m (9.8 ft.) - for mini D-Sub 15-pin/mini D-Sub
15-pin)
Computer cable
ELPKC10
(20 m (65.6 ft.) - for mini D-Sub 15-pin/mini
D-Sub 15-pin)
Use when connecting the projector to a computer.
Computer cable
ELPKC11
(1.8 m (6 ft.) - for mini D-Sub 15-pin/5BNC )
Use to connect the projector to a workstation.
Component video cable
ELPKC19
(3 m (9.8 ft.) - for mini D-Sub 15-pin/RCA x 3)
Use to connect a component video source.
Digital video cable
(3 m (9.8 ft.) - DVI-D male-male)
ELPKC20
DVI cable for connecting the projector to a computer
with a digital RGB output interface.
Use to connect the projector to connect two computers with
analog RGB output to the projector.
Remote control receiver
ELPST04
Use to control the projector with the remote control from a
distance.
Ceiling mount *
ELPMB07
Use when installing the projector to a ceiling.
Ceiling plate *
ELPFC03
Pipe 370 (370 mm (14.57 inches)/silver)*
ELPFP04
Pipe 570 (570 mm (22.44 inches)/silver)*
ELPFP05
Pipe 770 (770 mm (30.31 inches)/silver)*
ELPFP06
Use when installing the projector to a high ceiling or a
ceiling with veneer panels.
Image presentation camera
ELPDC02
ELPDC03
Use when projecting books, OHP films and slides.
Hard travel case
ELPKS26
Use this case if you need to carry the projector by hand.
Soft carrying case
ELPKS27
Use this case if you need to carry the projector by hand.
Appendices
* A special method of installation is required in order to suspend the projector from the ceiling. Please
contact the place of purchase if you would like to use this installation method.
53
List of Supported Signal Resolutions
Component Video Input/ RGB Video Input
Signal
Refresh rate (Hz)
SDTV (525i)
(D1)
60
800 × 600
(4:3 aspect)
800 × 450
(16:9 aspect)
SDTV (625i)
50
800 × 600
(4:3 aspect)
800 × 450
(16:9 aspect)
800 × 600
(4:3 aspect)
800 × 450
(16:9 aspect)
800 × 450
(16:9 aspect)
800 × 600
(4:3 aspect ratio with zoom)
800 × 450
(16:9 aspect)
800 × 600
(4:3 aspect ratio with zoom)
SDTV (525p)
(D2)
HDTV
(750p) 16:9
(D4)
HDTV(1125i)16:9
(D3)
Resolutions for resized display (dots)
Composite Video/ S-Video Input
Signal
54
Refresh rate (Hz)
Resolutions for resized display (dots)
TV (NTSC)
800 × 600
(4:3 aspect)
800 × 450
(16:9 aspect)
TV
(PAL, SECAM)
800 × 600
(4:3 aspect)
800 × 450
(16:9 aspect)
Component Video Input/ RGB Video Input
Computer
Composite Video/ S-Video Input
Computer
Signal
Refresh rate (Hz)
PC98
EGA
Resolution (dots)
Resolutions for
resized display
(resizing ON)
(dots)
Resolutions for
normal display
(resizing OFF)
(dots)
640 × 400
800 × 500
640 × 400
640 × 350
800 × 438
640 × 350
640 × 480
800 × 600
640 × 480
VGACGA
640 × 400
800 × 500
640 × 400
VGAEGA
640 × 350
800 × 438
640 × 350
720 × 400
800 × 444
720 × 400
720 × 350
800 × 388
720 × 350
72/75/85/
120, iMac*2
640 × 480
800 × 600
640 × 480
SVGA
56/60/72/75/
85 /120, iMac*2
800 × 600
800 × 600
800 × 600
XGA
43i/60/70/75/85/
120, iMac*2
1024 × 768
800 × 600
1024 × 768 *1
SXGA
70/75/85/100
1152 × 864
800 × 600
1152 × 864 *1
SXGA
60/70/85
1280 × 960
800 × 600
1280 × 960 *1
SXGA
43i/60/75/85
1280 × 1024
750 × 600
1280 × 1024 *1
SXGA+
60/75/85
1400 × 1050
800 × 600
1400 × 1050 *1
MAC13”
640 × 480
800 × 600
640 × 480
MAC16”
832 × 624
800 × 600
832 × 624 *1
MAC19”
1024 × 768
800 × 600
1024 × 768 *1
MAC21”
1152 × 870
794 × 600
1152 × 870 *1
VGA
60
VGA text
VESA
TV (525i)
60
640 × 480
800 × 600
640 × 480
TV (625i)
50
720 × 540
800 × 600
720 × 540
640 × 480
SDTV
(525p)
640 × 480
800 × 600
HDTV
(750p)
1280 × 720
800 × 450
1920 × 1080
800 × 450
HDTV(1125i, 1125p)
Appendices
*1 Virtual (window) display
*2 Connection is not possible if the equipment does not have a VGA output port.
55
Specifications
56
Product name
Home Theatre Projector EMP-TS10
Dimensions
348 (W) x 104 (H) x 274 (D) mm
(13.7 (W) x 4.09 (H) x 10.79 (D) inches) (not including protruding parts)
Panel size
0.9 inches
Display method
Polysilicon TFT active matrix
Drive method
Full-line 12-phase block sequential writing
Resolution
SVGA 480,000 pixels (800 (W) x 600 (H) dots) x 3
Focus adjustment
Manual
Zoom adjustment
Manual (approx. 1:1.35)
Lamp (light source)
UHE lamp, 150 W, Model No.: ELPLP17
Max. audio output
5W monaural
Speaker
1
Power supply
100 – 120 VAC, 2.7A
200 – 240 VAC, 1.3A
50/60 Hz
Operating
temperature
+5°C – +35°C (No condensation)
Storage
temperature
-10°C – +60°C (No condensation)
Weight
Approx. 4.2 kg (9.3 lbs)
Connectors
Computer 1:
1
DVI-I
Computer 2/Component
Video:
1
Mini D-Sub 15-pin (female)
Audio 1:
1
Stereo mini jack
Video:
1
RCA pin jack
S-Video:
1
Mini DIN 4-pin
Audio 2:
1
RCA pin jack x 2 (L, R)
USB:
1
USB connectors (B series)
Control (RS-232C):
1
D-Sub 9-pin (male)
Monitor Out:
1
Mini D-Sub 15-pin (female)
Remote:
1
Stereo mini jack
Safety
USA
UL1950 3rd Edition
Canada
CSA C22.2 No.950 -95 (cUL)
European Community
The Low Voltage Directive (73/23/EEC)
IEC60950 2nd Edition, +Amd.1, +Amd.2, +Amd.3, +Amd.4
EMC
USA
FCC 47CFR Part15B Class B (DoC)
Canada
ICES-003 Class B
European Community
The EMC Directive (89/336/EEC)
EN55022, 1998 Class B
EN55024, 1998
IEC61000-4-2, IEC61000-4-3, IEC61000-4-4, IEC61000-4-5,
IEC61000-4-6, IEC61000-4-8, IEC61000-4-11,
IEC61000-3-2, IEC61000-3-3
Appendices
Australia/New Zealand
AS/NZS 3548:1995, A1:1997, A2:1997 Class B
CISPR Pub.22:1993, A1:1995, A2:1996, Class B
57
Appearance
274
(10.79)
104
(4.09)
114
(4.49)
348
(13.7)
Units: mm (inch)
58
Part Names and Functions
Front/ Top
Rear
Control panel
Base
Remote control
Front/ Top
• Zoom
ring (p.11)
•
(Temperature)
indicator (p.37)
Indicates abnormalities in the
internal projector temperature.
•
(Lamp) indicator
(p.37)
Indicates a problem with the
projection lamp or that the
lamp needs to be replaced.
•
(Operation) indicator
(p.37)
Flashes or lights to indicate the
operating status of the
projector.
Adjusts the image size.
• Focus
ring (p.14)
Adjusts the image
focus.
• Lamp
cover (p.48)
Open this cover when replacing
the lamp unit inside the
projector.
• Lamp
cover opening switch
(p.48)
Slide this switch to unlock the lamp
cover when removing it.
• Control
• Security
(
lock
) (p.64)
panel (p.60)
• Air
exhaust
vent
• Handle
• Remote
control
light-receiving area
(Setup Guide)
Receives signals from the remote
control.
adjustable foot
(p.11)
Extend and retract to adjust
the projection angle.
• Lens
cover
Attach when not using the
projector to prevent the lens
from becoming dirty or
damaged.
• Foot
adjust button (p.11)
Press this button while lifting
up the projector in order to
make fine adjustments to the
adjustable foot or to retract it.
Appendices
• Front
Hold this handle when
lifting and transporting the
projector.
59
Part Names and Functions
Control Panel
• [Power]
• [Help]
button (p.7)
Turns the projector power
on and off.
• [Computer/YCbCr
• [Video]
]
button (p.7)
• [Esc]
Power
Help
Computer/YCbCr
Video
button (p.28)
Displays or hides the
menus.
Sync+
• [Shift]
button
(p.16, 17)
This button does not
function by itself. Press
and hold this button while
pressing either [Keystone]
button to activate the
function that is printed in
orange on the control panel
(Sync or Tracking ).
• [A/V
Mute] button
(p.30)
Turns off the audio and
video.
60
Esc
button
(p.13)
Press this button if the
projected image has
vertical keystone
distortion.
If you press and hold the
[Shift] button while
pressing this button, you
can adjust the
synchronization of
computer images.
Tracking -
Auto
Tracking +
Keystone
Shift
Sync-
Resize
A/V Mute
button (p.29, 36)
Press to cancel the function
currently being used. Pressing
[Esc] while viewing an
environment setting menu or
the online help displays the
previous screen or menu.
• [Auto]
Source
Menu
• [V-Keystone]
button (p.7)
Changes the image source
between the Video port and the
S-Video port.
Changes the image source
between the Computer 1
port and the Computer 2/
Component Video port.
• [Menu]
button (p.36)
Displays the online help menu
to assist you if you have a
problem.
Volume
button
(p.16, 28, 36)
Automatically adjusts the
computer image to the optimum
image.
Functions as an
button when
an environment setting menu or
help screen is being displayed.
Press to select an item and
proceed to the next screen.
• [H-Keystone]
button
(p.13)
Press this button if the
projected image has horizontal
keystone distortion.
If you press and hold the [Shift]
button while pressing this
button, you can adjust the
tracking of computer images.
• [Resize]
button (p.11, 15)
Changes the aspect ratio .
• [Volume] button
(p.18)
Adjusts the volume of the
built-in speaker.
Front/ Top
Rear
Control panel
Base
Remote control
Rear
• Monitor Out port (Setup Guide)
• Control (RS-232C) port
Connects the projector to a computer using an
RS-232C cable. This port is for service use,
and should not normally be used.
• USB port (Setup Guide)
Connects the projector to a computer
using a USB cable.
Outputs the projected analog image signal from a
computer to an external monitor.
This is not available for digital image signals being
input to the Computer 1 port or signals from other
video sources.
Remove the cover when using this port.
• Computer 2/ Component Video port
(Setup Guide)
• Remote control
Inputs component video images from a video
source or analog video signals from a computer.
light-receiving area
(Setup Guide)
• Computer 1 port (Setup Guide)
Receives signals from
the remote control.
Inputs digital/analog RGB image
signals from a computer.
• Speaker
• Power inlet (p.6)
Connects the power cord.
• Rear adjustable foot
(p.12)
Extend and retract to adjust
the horizontal projection
angle.
• Audio 1 port
(Setup Guide)
Inputs audio signals.
Connects using a stereo
mini jack.
• Remote port
Connects an optional
remote control receiver to
the projector.
• S-Video port
• Video port (Setup Guide)
(Setup Guide)
Inputs an S-Video
signal to the projector from
other video sources.
Inputs composite video signals to
the projector from other video
sources.
• Audio 2 port (Setup Guide)
Inputs audio signals.
Base
• Front adjustable foot
• Air filter (air inlet)
(p.46, 50)
Prevents dust and other
foreign particles from
being drawn into the
projector.
When replacing the lamp,
replace the air filter also.
bracket fixing points
(4 points)
(p.53, Setup Guide)
Appendices
• Suspension
• Rear adjustable foot
Install the optional ceiling
mount here when suspending
the projector from the ceiling.
61
Part Names and Functions
Front/ Top
Rear
Control panel
Base
Remote control
Remote Control
• Remote control light-emitting area (Setup Guide)
Outputs infrared remote control signals.
• [Freeze] button (p.30)
Keeps the current computer or
video image on the screen.
• [A/V Mute] button (p.30)
Turns off the audio and video.
• [E-Zoom] button (p.31)
Enlarges or reduces the size of the
image without changing the size of
the projection area.
• Colortune button (p.14)
Changes the color mode in
accordance with the button pressed.
•[
(Illumination) ] button
(Setup Guide)
All buttons other than the [Enter],
[Esc] and
buttons illuminate for
10 seconds each time this button is
pressed.
• Cover
Open to use the buttons that are
underneath the cover.
• Indicator
Lights when a remote control signal is
being output.
• [Power] button (p.7)
Turns the projector power on and off.
• R/C switch (p.7)
Turns the remote control power on and
off.
• [Enter] button
(p.28, 36, Setup Guide)
If pressed when an environment setting
menu or help screen is being displayed,
the menu item is selected and the next
menu screen appears.
If a computer is connected and the
remote control is being used as a
wireless mouse, the button can be tilted
up, down and to the left or right to move
the pointer in the tilted direction. When
pressed, it functions in the same way as
a left mouse button.
• [Esc] button
(p.29, 36, Setup Guide)
Press to cancel the function currently
being used. Pressing [Esc] while
viewing an environment setting menu
or the online help displays the previous
screen or menu. If a computer is
connected and the remote control is
being used as a wireless mouse, it
functions as a right mouse button.
Underneath cover
• [Menu] button (p.28)
Displays or hides the environment
setting menus.
• [Comp1] button (p.7)
Changes the image source to the
signals being input to the Computer
1 port.
• [S-Video] button (p.7)
Switches to the images input from
the S-Video port.
• [Auto] button (p.16)
Automatically adjusts computer
images to the optimum images.
• [P in P] button (p.32)
Activates the P in P (Picture in
Picture) function.
• [Volume] button (p.18)
Adjusts the volume of the built-in
speaker.
62
• [Help] button (p.36)
Displays the online help menu.
• [Comp2/YCbCr] button (p.7)
Changes the image source to the
signals being input to the Computer
2/Component Video port.
• [Video] button (p.7)
Switches to the images input from
the Video port.
• [Resize] button (p.11, 15)
Changes the aspect ratio
.
• [Preset] button (p.22)
Selects one of the computer image
resolutions that have been preset.
Glossary
5BNC
A port used to input analog video signals.
A/V Mute
The momentary canceling of audio and video output. This projector has an [A/V Mute]
button which you can press to momentarily stop the projection of pictures and sound. The
picture and sound can be restored by pressing the [A/V Mute] button on the projector’s
control panel or the remote control once more.
Aspect ratio
The ratio between an image's length and its height. HDTV images have an aspect ratio of 16:9
and appear elongated. The aspect ratio for standard images is 4:3.
Color
difference
signal
(component)
A type of video signal output by video equipment which actually consists of three separate
signals: a red + luminance signal (R-Y), a luminance signal (Y) and a blue + luminance signal
(B-Y). Each signal is transmitted along a separate cable. Color difference signals generally
result in a better image than composite signals (in which the red, green and blue signals and
the luminance signal are all transmitted along a single cable).
Color
temperature
The temperature of an object which is emitting light. If the color temperature is high, the
colors tend to take on a bluish tinge. If the color temperature is lower, the colors tend to take
on a reddish tinge.
Component video
Video signals which have the video brightness signals and color signals separated, in order to
provide better image quality.
In high-definition TV (HDTV), it refers to images which consist of three independent signals:
Y (luminance signal), and Pb and Pr (color difference signals ).
Composite video
Video signals which have the video brightness signals and color signals mixed together. The
type of signals commonly used by household video equipment (NTSC format).
The signals consist of the carrier signal Y (luminance signal) and the chroma (color) signal
which are contained in the color bar signal.
Contrast
The relative brightness of the light and dark areas of an image can be increased or decreased
in order to make text and graphics stand out more clearly, or to make them appear softer.
Cool-down
The cooling process for the projector's lamp unit continues even after the [Power] button has
been pressed to turn off the lamp. After the lamp turns off, the cooling fan continues
operating, but all button operations are disabled. The length of time that this is happening is
called the "cool-down period". The cool-down period lasts for about 2 minutes. The actual
time will vary depending on the external air temperature.
DFP
Abbreviation for Digital Flat Panel. Refers to a standard method for digital transmission of
video signals.
Dolby Digital
A proprietary sound format developed by Dolby Laboratories. Normal stereo is a 2-channel
format that uses two speakers. Dolby Digital is a 6-channel (5.1 channel) format that adds to
this a center speaker, two rear speakers and a sub-woofer.
DVI
Abbreviation for Digital Visual Interface. Refers to a standard method for digital transmission
of video signals.
DVI is a standard which has also been applied to digital household electronic equipment other
than computers. It allows images to be transmitted at higher resolutions than for DFP.
Freeze
The momentary pausing of image playback only. When the [Freeze] button is pressed, the
image playback only can be paused. When the [Freeze] button is pressed again, playback
resumes.
HDTV
An abbreviation for High-Definition Television. It refers to high-definition systems which
satisfy the following conditions.
Vertical resolution of 750p or 1125i or greater
(p = progressive scanning, i = interlaced scanning )
Screen aspect ratio of 16:9
Dolby Digital audio reception and playback (or output)
Interlaced
scanning
A method of image scanning whereby the signal bandwidth used is approximately half that
required for sequential scanning when images with the same still picture resolution are
broadcast.
Refresh Rate
The light-emitting element of a display maintains the same luminosity and color for an
extremely short time. Because of this, the image must be scanned many times per second in
order to refresh the light emitting element. The number of refresh operations per second is
called the "refresh rate", and is expressed in hertz (Hz).
Appendices
Following is an explanation of some of the terms used in this guide which may be unfamiliar or which were
not explained in the manual itself. Further information can be obtained by referring to other commerciallyavailable publications.
63
Glossary
64
S-Video
A video signal which has the luminance component and color component separated in order
to provide better image quality.
It refers to images which consist of two independent signals: Y (luminance signal), and C
(color signal).
SDTV
An abbreviation for Standard Definition Television. It refers to standard television systems
which do not satisfy the conditions for High-Definition Television.
Security lock
A device consisting of a projector case with a hole in it that a commercially-available theftprevention cable can be passed through in order to secure the device to a table or pillar. This
projector is compatible with the Microsaver Security System manufactured by Kensington.
sRGB
An international standard for color intervals that was formulated so that colors which are
reproduced by video equipment can be handled easily by computer operating systems (OS)
and the Internet.
SVGA
A type of video signal with a resolution of 800 (horizontal) x 600 (vertical) dots which is used
by IBM PC/AT-compatible computers (DOS/V computers).
SXGA
A type of video signal with a resolution of 1,280 (horizontal) x 1,024 (vertical) dots which is
used by IBM PC/AT-compatible computers (DOS/V computers).
Sync
(synchronization)
The signals output from computers have a specific frequency. If the projector frequency does
not match this frequency, the resulting images will not be of a good quality. The process of
matching the phases of these signals (the relative position of the crests and troughs in the
signal) is called "synchronization". If the signals are not synchronized, problems such as
flickering, blurriness and horizontal interference can occur.
Tracking
The signals output from computers have a specific frequency. If the projector frequency does
not match this frequency, the resulting images will not be of a good quality. The process of
matching the frequency of these signals (the number of crests in the signal) is called
“tracking”. If tracking is not carried out correctly, wide vertical stripes will appear in the
projected images.
USB
An abbreviation for Universal Serial Bus. USB is an interface for connecting personal
computers to peripheral devices which only support relatively low data transmission speeds.
VGA
A type of video signal with a resolution of 640 (horizontal) x 480 (vertical) dots which is used
by IBM PC/AT-compatible computers (DOS/V computers).
XGA
A type of video signal with a resolution of 1,024 (horizontal) x 768 (vertical) dots which is
used by IBM PC/AT-compatible computers (DOS/V computers).
YCbCr
The carrier signal which is contained in the color bar signal used in modern TV transmissions
(NTSC format). The name comes from the Y (luminance) signal and the CbCr (chroma
[color]) signals.
YPbPr
The carrier signal which is contained in the color bar signal used in high-definition TV
(HDTV) transmissions. The name comes from the Y (luminance) signal and the PbPr (color
difference) signals .
Index
General Terms
A
A/V Mute function ...............................................24, 30
About menu................................................................26
Advanced menu..........................................................25
DVI ............................................................................ 53
E
Environment Setting Menu Functions....................... 20
External monitor.........................................Setup Guide
E-Zoom function ....................................................... 31
Air filter cleaning .......................................................46
F
Air filter replacement .................................................50
Focus ring ............................................................ 14, 59
Appearance.................................................................58
Focus.......................................................................... 14
Aspect ratio ................................................................15
Foot adjust button ................................................ 11, 59
Audio input ................................................................23
Foot adjustment ......................................................... 11
Audio menu................................................................23
Freeze function .......................................................... 30
Audio1 port ..........................................61, Setup Guide
Frequency .................................................................. 26
Audio2 port ..........................................61, Setup Guide
Front adjustable foot...................................... 13, 59, 61
Automatic adjustment ................................................16
G
B
Glossary..................................................................... 63
Bass ............................................................................23
H
Battery compartment cover (Remote control)
................................................................Setup Guide
Battery Replacement Period and Cautions
(Remote control).....................................Setup Guide
Brightness.............................................................21, 22
Handle ....................................................................... 59
HDTV.................................................................. 15, 54
Horizontal keystone............................................. 13, 24
I
C
Image adjustment ...................................................... 14
Ceiling ......................................25, 53, 61, Setup Guide
Indicators ............................................................. 37, 59
Cleaning .....................................................................46
Input signal ................................................................ 26
Color adjustment ........................................................25
Inserting batteries (Remote control)...........Setup Guide
Color mode.....................................................14, 21, 22
Installation ..................................................Setup Guide
Color temperature ......................................................25
K
Color...........................................................................21
Keystone correction................................................... 12
COM port ...................................................................25
Component video ...........................54, 61, Setup Guide
L
Composite video ............................ 54, 61, Setup Guide
Lamp cover .......................................................... 48, 59
Computer connections................................Setup Guide
Lamp indicator .................................................... 37, 59
Computer1 port ................................ 7, 61, Setup Guide
Lamp replacement period .......................................... 47
Computer2/ Component Video port
...................................................... 7, 61, Setup Guide
Lamp replacement ..................................................... 48
Connectors ...........................................................56, 61
Lamp.................................................................... 26, 49
Contrast ................................................................21, 22
Language ................................................................... 25
Control (RS-232C) port .............................................61
Lens cleaning............................................................. 46
Control panel..............................................................60
Lens cover ................................................................. 59
Cross...........................................................................31
Appendices
Cool-down..............................................................9, 37
Lamp resetting ..................................................... 26, 49
M
Main menu................................................................. 20
D
Menus ........................................................................ 20
DFP ............................................................................53
Monitor out port ...................................61, Setup Guide
Digital video cable .....................................................53
Digital-RGB ...................................53, 61, Setup Guide
65
Index
N
Storage temperature ................................................... 56
Noise reduction.......................................................... 21
Sub-menu ................................................................... 20
No-Signal................................................................... 24
Supported Signal Resolutions.................................... 54
O
Operating temperature ............................................... 56
Operation indicator.............................................. 37, 59
Optional accessories .................................................. 53
Overheating ............................................................... 38
P
S-Video .......................................... 54, 64, Setup Guide
S-Video port..................................... 7, 61, Setup Guide
SYNC Mode .............................................................. 26
SYNC Polarity ........................................................... 26
Sync ..................................................................... 17, 22
Synchronization ................................................... 17, 22
T
P in P function ..................................................... 24, 32
Temperature indicator .......................................... 37, 59
Part Names and Functions ......................................... 59
Tint ............................................................................. 21
Picture in Picture ................................................. 24, 32
Tracking ............................................................... 17, 22
Position .......................................................... 16, 21, 22
Treble ......................................................................... 23
Power cord................................................................... 6
Turning off ................................................................... 9
Power inlet............................................................. 6, 61
Preset ......................................................................... 22
U
Projection angle ......................................................... 11
USB port .............................................. 61, Setup Guide
Projection distance......................................Setup Guide
USB mouse ................................................ Setup Guide
Prompt ....................................................................... 24
User's Logo menu ...................................................... 24
R
R/C switch ............................................................. 7, 62
User's Logo saving..................................................... 51
Using the Help ........................................................... 36
Using the Menus ........................................................ 28
Rear adjustable foot............................................. 12, 61
Refresh Rate .............................................................. 26
V
Remote port ............................................................... 61
Vertical keystone .................................................. 13, 23
Remote control light-receiving area
.....................................................59, 61, Setup Guide
Video port ........................................ 7, 61, Setup Guide
Remote control light-emitting area.......62, Setup Guide
Video Signal......................................................... 21, 26
Remote control .....................................62, Setup Guide
Video source connection ............................ Setup Guide
Reset All menu .......................................................... 27
Video Source.............................................................. 26
Resized display.............................................. 11, 15, 54
Volume ................................................................. 18, 23
Resolution...................................................... 22, 26, 55
RGB .......................................................................... 25
RGB video ......................................20, 54, Setup Guide
S
Screen size ..................................................Setup Guide
SDTV................................................................... 15, 54
Security lock.............................................................. 59
Setting menu.............................................................. 23
W
Wide-screen ............................................................... 15
Window display ......................................................... 11
Wireless mouse .......................................... Setup Guide
Y
YCbCr.................................................................. 20, 24
YPbPr......................................................................... 20
Sharpness............................................................. 21, 22
Z
Sleep mode ................................................................ 24
Zoom ring ............................................................ 11, 59
Speaker ...................................................................... 61
Specifications............................................................. 56
sRGB ............................................................. 14, 21, 22
Startup screen ............................................................ 25
66
Video menu ................................................................ 20
DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B
Personal Computers
We
Located at
Tel
: EPSON AMERICA, INC.
: 3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
: 562-290-5254
Declare under sole responsibility that the product identified herein, complies with 47CFR
Part 2 and 15 of the FCC rules as a Class B digital device. Each product marketed, is
identical to the representative unit tested and found to be compliant with the standards.
Records maintained continue to reflect the equipment being produced can be expected
to be within the variation accepted, due to quantity production and testing on a statistical
basis as required by 47CFR 2.909. Operation is subject to the following two conditions :
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Trade Name
: EPSON
Type of Product
: Projector
Model
: EMP-TS10 / ELP-TS10
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio or
television reception. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to radio and television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this equipment will
invalidate the FCC Certification or Declaration of this device and may cause interference
levels which exceed the limits established by the FCC for this equipment. It is the
responsibility of the user to obtain and use a shielded equipment interface cable with this
device. If this equipment has more than one interface connector, do not leave cables
connected to unused interfaces. Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, without the prior written permission of SEIKO EPSON CORPORATION. No patent
liability is assumed with respect to the use of the information contained herein. Neither is any liability
assumed for damages resulting from the use of the information contained herein.
Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of this
product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties
as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or
alterations to this product, or (excluding the U.S.) failure to strictly comply with SEIKO EPSON
CORPORATION’s operating and maintenance instructions.
SEIKO EPSON CORPORATION shall not be liable against any damages or problems arising from
the use of any options or any consumable products other than those designated as Original EPSON
Products or EPSON Approved Products by SEIKO EPSON CORPORATION.
EPSON is a registered trademark and PowerLite is a trademark of SEIKO EPSON CORPORATION.
General Notice: The following trademarks and registered trademarks are the property of their
respective owners and are used in this publication for identification purposes only.
• EPSON/Seiko Epson Corp.
• Macintosh, PowerBook/Apple Computer Inc.
• IBM/International Business Machine Corp.
• Windows/Microsoft Corp.
Other product names used herein are also for identification purposes only and may be trademarks of
their respective owners. EPSON disclaims any and all rights in those marks.
Copyright
2002 by SEIKO EPSON CORPORATION
E
Printed on 100% recycled paper.
Printed in Japan
402171700
(9002556)
02.01-.*A(C05)