Bosch UML-150-90 User`s manual

General Purpose LCD Monitors
UML-150-90 | UML-170-90 | UML-190-90
en
User’s Manual
General Purpose LCD Monitors
Table of Contents | en
iii
Table of Contents
1
Safety
1
1.1
Important Safety Instructions
1
1.2
Safety Precautions
3
1.3
Important Notices
3
1.4
Customer Support and Service
8
2
Unpacking
9
2.1
Parts List
9
3
Exploded View
10
4
Description
11
4.1
Features
12
4.2
Power
12
5
Installing the Monitor
12
5.1
Ventilation
12
5.2
Mounting the Monitor
12
5.2.1
Desktop Installation
12
5.2.2
Wall Mount Installation
13
5.3
Connecting the Composite Video Signal to the Monitor
14
5.4
Connecting the Y/C (S-Video) Signal to the Monitor
14
5.5
Connecting the PC Signal to the Monitor
14
5.6
Single / Multiple Monitor Configuration
15
6
Navigating the Monitor
16
6.1
Navigating the Front Panel
16
6.2
Navigating the Monitor On-screen Display (OSD)
16
6.3
On-screen Display Menus
17
6.4
Video Mode
18
6.5
Screen
18
6.6
Audio
19
6.7
OSD
19
6.8
Color (PC mode)
20
6.9
Utility
20
6.10
Exit
21
7
Power Management
21
7.1
Power Consumption
21
7.2
LED Indicator
21
Bosch Security Systems, Inc.
User’s Manual
F.01U.078.454 | 1.0 | 2008.03
iv
en | Table of Contents
General Purpose LCD Monitors
8
Trouble Shooting Guide
22
9
Maintenance
22
10
Technical Specifications
24
F.01U.078.454 | 1.0 | 2008.03
User’s Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
Safety | en
1
Safety
1.1
Important Safety Instructions
1
Read, follow, and retain for future reference all of the following safety instructions. Heed all
warnings on the unit and in the operating instructions before operating the unit.
1.
Cleaning - Unplug the unit from the outlet before cleaning. Follow any instructions
provided with the unit. Generally, using a dry cloth for cleaning is sufficient, but a moist
fluff-free cloth or leather shammy may also be used. Do not use liquid cleaners or aerosol
cleaners.
2.
Heat Sources - Do not install the unit near any heat sources such as radiators, heaters,
stoves, or other equipment (including amplifiers) that produce heat.
3.
Ventilation - Any openings in the unit enclosure are provided for ventilation to prevent
overheating and ensure reliable operation. Do not block or cover these openings. Do not
place the unit in an enclosure unless proper ventilation is provided, or the manufacturer's
instructions have been adhered to.
4.
Water - Do not use this unit near water, for example near a bathtub, washbowl, sink,
laundry basket, in a damp or wet basement, near a swimming pool, in an outdoor
installation, or in any area classified as a wet location. To reduce the risk of fire or
electrical shock, do not expose this unit to rain or moisture.
5.
Object and liquid entry - Never push objects of any kind into this unit through openings
as they may touch dangerous voltage points or short-out parts that could result in a fire
or electrical shock. Never spill liquid of any kind on the unit. Do not place objects filled
with liquids, such as vases or cups, on the unit.
6.
Lightning - For added protection during a lightning storm, or when leaving this unit
unattended and unused for long periods, unplug the unit from the wall outlet and
disconnect the cable system. This will prevent damage to the unit from lightning and
power line surges.
7.
Controls adjustment - Adjust only those controls specified in the operating instructions.
Improper adjustment of other controls may cause damage to the unit. Use of controls or
adjustments, or performance of procedures other than those specified, may result in
hazardous radiation exposure.
8.
Overloading - Do not overload outlets and extension cords. This can cause fire or
electrical shock.
9.
Power cord and plug protection - Protect the plug and power cord from foot traffic,
being pinched by items placed upon or against them at electrical outlets, and its exit
from the unit. For units intended to operate with 230 VAC, 50 Hz, the input and output
power cord must comply with the latest versions of IEC Publication 227 or IEC Publication
245.
10. Power disconnect - Units with or without ON/OFF switches have power supplied to the
unit whenever the power cord is inserted into the power source; however, the unit is
operational only when the ON/OFF switch is in the ON position. The power cord is the
main power disconnect device for switching off the voltage for all units.
Bosch Security Systems, Inc.
User’s Manual
F.01U.075.713 | 1.0 | 2008.03
2
en | Safety
High Performance LCD Monitors
11. Power sources - Operate the unit only from the type of power source indicated on the
label. Before proceeding, be sure to disconnect the power from the cable to be installed
into the unit.
–
For battery powered units, refer to the operating instructions.
–
For external power supplied units, use only the recommended or approved power
supplies.
–
For limited power source units, this power source must comply with EN60950.
Substitutions may damage the unit or cause fire or shock.
–
For 24 VAC units, voltage applied to the unit's power input should not exceed ±10%,
or 28 VAC. User-supplied wiring must comply with local electrical codes (Class 2
power levels). Do not ground the supply at the terminals or at the unit's power
supply terminals.
–
If unsure of the type of power supply to use, contact your dealer or local power
company.
12. Servicing - Do not attempt to service this unit yourself. Opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
13. Damage requiring service - Unplug the unit from the main AC power source and refer
servicing to qualified service personnel when any damage to the equipment has occurred,
such as:
–
the power supply cord or plug is damaged;
–
exposure to moisture, water, and/or inclement weather (rain, snow, etc.);
–
liquid has been spilled in or on the equipment;
–
an object has fallen into the unit;
–
unit has been dropped or the unit cabinet is damaged;
–
unit exhibits a distinct change in performance;
–
unit does not operate normally when the user correctly follows the operating
instructions.
14. Replacement parts - Be sure the service technician uses replacement parts specified by
the manufacturer, or that have the same characteristics as the original parts.
Unauthorized substitutions may cause fire, electrical shock, or other hazards.
15. Safety check - Safety checks should be performed upon completion of service or repairs
to the unit to ensure proper operating condition.
16. Installation - Install in accordance with the manufacturer's instructions and in
accordance with applicable local codes.
17. Attachments, changes or modifications - Only use attachments/accessories specified by
the manufacturer. Any change or modification of the equipment, not expressly approved
by Bosch, could void the warranty or, in the case of an authorization agreement, authority
to operate the equipment.
F.01U.075.713 | 1.0 | 2008.03
User’s Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
1.2
Safety | en
3
Safety Precautions
DANGER! High risk:
This symbol indicates an imminently hazardous situation such as “Dangerous Voltage”
inside the product. If not avoided, this will result in an electrical shock, serious bodily
injury, or death.
!
!
!
i
1.3
WARNING! Medium risk:
Indicates a potentially hazardous situation. If not avoided, this could result in serious bodily
injury or death.
CAUTION! Medium Risk
Indicates a potentially hazardous situation. If not avoided, this may result in minor or
moderate injury. Alerts the user to important instructions accompanying the unit.
CAUTION! Low risk: (without safety alert symbol)
Indicates a potentially hazardous situation. If not avoided, this may result in property
damage or risk of damage to the unit.
NOTICE!
This symbol indicates information or a company policy that relates directly or indirectly to
the safety of personnel or protection of property.
Important Notices
Accessories - Do not place this unit on an unstable stand, tripod, bracket, or mount. The unit
may fall, causing serious injury and/or serious damage to the unit. Use only with the cart,
stand, tripod, bracket, or table specified by the manufacturer. When a cart is used, use
caution and care when moving the cart/apparatus combination to avoid injury from tip-over.
Quick stops, excessive force, or uneven surfaces may cause the cart/unit combination to
overturn. Mount the unit per the manufacturer's instructions.
All-pole power switch - Incorporate an all-pole power switch, with a contact separation of at
least 3 mm in each pole, into the electrical installation of the building.
If it is needed to open the housing for servicing and/or other activities, use this all-pole switch
as the main disconnect device for switching off the voltage to the unit.
Camera grounding - For mounting the camera in potentially damp environments, ensure to
ground the system using the ground connection of the power supply connector (see section:
Connecting external power supply).
Camera lens - An assembled camera lens in the outdoor housing must comply and be tested in
accordance with UL/IEC60950. Any output or signal lines from the camera must be SELV or
Limited Power Source. For safety reasons the environmental specification of the camera lens
assembly must be within the environmental specification of -10 °C (14 °F) to 50 °C (122 °F).
Camera signal - Protect the cable with a primary protector if the camera signal is beyond 140
feet, in accordance with NEC800 (CEC Section 60).
Coax grounding:
–
Ground the cable system if connecting an outside cable system to the unit.
–
Connect outdoor equipment to the unit's inputs only after this unit has had its grounding
plug connected to a grounded outlet or its ground terminal is properly connected to a
ground source.
Bosch Security Systems, Inc.
User’s Manual
F.01U.075.713 | 1.0 | 2008.03
4
en | Safety
High Performance LCD Monitors
–
Disconnect the unit's input connectors from outdoor equipment before disconnecting the
grounding plug or grounding terminal.
–
Follow proper safety precautions such as grounding for any outdoor device connected to
this unit.
U.S.A. models only - Section 810 of the National Electrical Code, ANSI/NFPA No.70, provides
information regarding proper grounding of the mount and supporting structure, grounding of
the coax to a discharge unit, size of grounding conductors, location of discharge unit,
connection to grounding electrodes, and requirements for the grounding electrode.
i
NOTICE!
This device is intended for use in public areas only.
U.S. federal law strictly prohibits surreptitious recording of oral communications.
Your Bosch product was developed and manufactured with high-quality material and
components that can be recycled and reused. This symbol means that electronic and
electrical appliances, which have reached the end of their working life, must be collected and
disposed of separately from household waste material. Separate collecting systems are
usually in place for disused electronic and electrical products. Please dispose of these units at
an environmentally compatible recycling facility, per European Directive 2002/96/EC.
Environmental statement - Bosch has a strong commitment towards the environment. This
unit has been designed to respect the environment as much as possible.
Electrostatic-sensitive device - Use proper CMOS/MOS-FET handling precautions to avoid
electrostatic discharge.
NOTE: Wear required grounded wrist straps and observe proper ESD safety precautions when
handling the electrostatic-sensitive printed circuit boards.
Fuse rating - For security protection of the device, the branch circuit protection must be
secured with a maximum fuse rating of 16A. This must be in accordance with NEC800 (CEC
Section 60).
Grounding and polarization - This unit may be equipped with a polarized alternating current
line plug (a plug with one blade wider than the other blade). This safety feature allows the
plug to fit into the power outlet in only one way. If unable to insert the plug fully into the
outlet, contact a locally certified electrician to replace the obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
Alternately, this unit may be equipped with a 3-pole grounding plug (a plug with a third pin for
earth grounding). This safety feature allows the plug to fit into a grounded power outlet only.
If unable to insert the plug into the outlet, contact a locally certified electrician to replace the
obsolete outlet. Do not defeat the safety purpose of the grounding plug.
Moving - Disconnect the power before moving the unit. Move the unit with care. Excessive
force or shock may damage the unit and the hard disk drives.
Outdoor signals - The installation for outdoor signals, especially regarding clearance from
power and lightning conductors and transient protection, must be in accordance with NEC725
and NEC800 (CEC Rule 16-224 and CEC Section 60).
Permanently connected equipment - Incorporate a readily accessible disconnect device in
the building installation wiring.
Pluggable equipment - Install the socket outlet near the equipment so it is easily accessible.
PoE - Never supply power via the Ethernet connection (PoE) when power is already supplied
via the power connector.
Power disconnect - Units have power supplied whenever the power cord is inserted into the
power source. The power cord is the main power disconnect for all units.
F.01U.075.713 | 1.0 | 2008.03
User’s Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
Safety | en
5
Power lines - Do not locate the camera near overhead power lines, power circuits, or
electrical lights, nor where it may contact such power lines, circuits, or lights.
SELV
All the input/output ports are Safety Extra Low Voltage (SELV) circuits. SELV circuits should
only be connected to other SELV circuits.
Because the ISDN circuits are treated like telephone-network voltage, avoid connecting the
SELV circuit to the Telephone Network Voltage (TNV) circuits.
Video loss - Video loss is inherent to digital video recording; therefore, Bosch Security
Systems cannot be held liable for any damage that results from missing video information. To
minimize the risk of lost digital information, Bosch Security Systems recommends multiple,
redundant recording systems, and a procedure to back up all analog and digital information.
i
NOTICE!
This is a class A product. In a domestic environment this product may cause radio
interference, in which case the user may be required to take adequate measures.
FCC & ICES INFORMATION
(U.S.A. and Canadian Models Only)
This device complies with part 15 of the FCC Rules. Operation is subject to the following
conditions:
–
–
this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause
undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules and ICES-003 of Industry Canada. These limits
are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and
radiates radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his expense.
Intentional or unintentional modifications, not expressly approved by the party responsible for
compliance, shall not be made. Any such modifications could void the user's authority to
operate the equipment. If necessary, the user should consult the dealer or an experienced
radio/television technician for corrective action.
The user may find the following booklet, prepared by the Federal Communications
Commission, helpful: How to Identify and Resolve Radio-TV Interference Problems. This
booklet is available from the U.S. Government Printing Office, Washington, DC 20402, Stock
No. 004-000-00345-4.
Bosch Security Systems, Inc.
User’s Manual
F.01U.075.713 | 1.0 | 2008.03
6
en | Safety
High Performance LCD Monitors
INFORMATIONS FCC ET ICES
(modèles utilisés aux États-Unis et au Canada uniquement)
Ce produit est conforme aux normes FCC partie 15. la mise en service est soumises aux deux
conditions suivantes:
–
–
cet appareil ne peut pas provoquer d'interférence nuisible et
cet appareil doit pouvoir tolérer toutes les interférences auxquelles il est soumit, y
compris les interférences qui pourraient influer sur son bon fonctionnement.
AVERTISSEMENT: Suite à différents tests, cet appareil s’est révélé conforme aux exigences
imposées aux appareils numériques de Classe A en vertu de la section 15 du règlement de la
Commission fédérale des communications des États-Unis (FCC). Ces contraintes sont
destinées à fournir une protection raisonnable contre les interférences nuisibles quand
l'appareil est utilisé dans une installation commerciale. Cette appareil génère, utilise et émet
de l'energie de fréquence radio, et peut, en cas d'installation ou d'utilisation non conforme
aux instructions, générer des interférences nuisibles aux communications radio. L’utilisation
de ce produit dans une zone résidentielle peut provoquer des interférences nuisibles. Le cas
échéant, l’utilisateur devra remédier à ces interférences à ses propres frais.
Au besoin, l’utilisateur consultera son revendeur ou un technicien qualifié en radio/télévision,
qui procédera à une opération corrective. La brochure suivante, publiée par la Commission
fédérale des communications (FCC), peut s’avérer utile : « How to Identify and Resolve RadioTV Interference Problems » (Comment identifier et résoudre les problèmes d’interférences de
radio et de télévision). Cette brochure est disponible auprès du U.S. Government Printing
Office, Washington, DC 20402, États-Unis, sous la référence n° 004-000-00345-4.
AVERTISSEMENT: Ce produit est un appareil de Classe A. Son utilisation dans une zone
résidentielle risque de provoquer des interférences. Le cas échéant, l’utilisateur devra
prendre les mesures nécessaires pour y remédier.
Disclaimer
Underwriter Laboratories Inc. (“UL”) has not tested the performance or reliability of the
security or signaling aspects of this product. UL has only tested fire, shock and/or casualty
hazards as outlined in UL's Standard(s) for Safety for Closed Circuit Television Equipment, UL
2044. UL Certification does not cover the performance or reliability of the security or signaling
aspects of this product.
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR CERTIFICATIONS WHATSOEVER
REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED
FUNCTIONS OF THIS PRODUCT.
Disclaimer
Underwriter Laboratories Inc. (“UL”) has not tested the performance or reliability of the
security or signaling aspects of this product. UL has only tested fire, shock and/or casualty
hazards as outlined in UL's Standard(s) for Safety for Information Technology Equipment, UL
60950-1. UL Certification does not cover the performance or reliability of the security or
signaling aspects of this product.
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR CERTIFICATIONS WHATSOEVER
REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING-RELATED
FUNCTIONS OF THIS PRODUCT.
F.01U.075.713 | 1.0 | 2008.03
User’s Manual
Bosch Security Systems, Inc.
High Performance LCD Monitors
Safety | en
7
Copyright
This user guide is the intellectual property of Bosch Security Systems, Inc. and is protected by
copyright.
All rights reserved.
Trademarks
All hardware and software product names used in this document are likely to be registered
trademarks and must be treated accordingly.
NOTICE!
This user guide has been compiled with great care and the information it contains has been
i
thoroughly verified. The text was complete and correct at the time of printing. The ongoing
development of the products may mean that the content of the user guide can change without
notice. Bosch Security Systems accepts no liability for damage resulting directly or indirectly
from faults, incompleteness or discrepancies between the user guide and the product
described.
Bosch Security Systems, Inc.
User’s Manual
F.01U.075.713 | 1.0 | 2008.03
8
1.4
en | Safety
High Performance LCD Monitors
Customer Support and Service
If this unit needs service, contact the nearest Bosch Security Systems Service Center for
authorization to return and shipping instructions.
Service Centers
USA
Telephone: 800-366-2283 or 585-340-4162
Fax: 800-366-1329
Email: cctv.repair@us.bosch.com
Customer Service
Telephone: 888-289-0096
Fax: 585-223-9180
Email: security.sales@us.bosch.com
Technical Support
Telephone: 800-326-1450
Fax: 585-223-3508 or 717-735-6560
Email: technical.support@us.bosch.com
Repair Center
Telephone: 585-421-4220
Fax: 585-223-9180 or 717-735-6561
Email: security.repair@us.bosch.com
Canada
Telephone: 514-738-2434
Fax: 514-738-8480
Europe, Middle East & Asia Pacific Region
Telephone: 44 (0) 1495 274558
Fax: 44 (0) 1495 274280
Email: rmahelpdesk@solectron.com
More information
For additional information, please contact your Bosch Security Systems representative or visit
our web site at www.boschsecurity.com
F.01U.075.713 | 1.0 | 2008.03
User’s Manual
Bosch Security Systems, Inc.
General Purpose LCD Monitors
2
Unpacking | en
9
Unpacking
This equipment should be unpacked and handled with care. If an item appears to have been
damaged in shipment, notify the shipper immediately.
Verify that all the parts listed in the Parts List below are included. If any items are missing,
notify your Bosch Security Systems Sales or Customer Service Representative.
The original packing carton is the safest container in which to transport the unit and must be
used if returning the unit for service. Save it for possible future use.
2.1
Parts List
The following table lists the parts included:
Quantity
Part
1
UML-150-90, UML-170-90, or UML-190-90 Color LCD Flat Panel Monitor
1
Installation manual
2
Power Cords, 3-wire with grounded plug 1.8 m (6 ft) long:
one with a U.S plug type and one with a European Continental plug type
1
VGA to VGA (D-SUB) cable, 1.5 m (5 ft)
1
Power Supply (brick):
UML-150-50: 12 VDC, 3.3 A, 100–240 VAC, 50/60 Hz
UML-170-50: 12 VDC, 4.1 A, 100–240 VAC, 50/60 Hz
UML-190-90: 12 VDC, 4.1 A, 100-240 VAC, 50/60 Hz
Bosch Security Systems, Inc.
User’s Manual
F.01U.078.454 | 1.0 | 2008.03
10
3
en | Exploded View
General Purpose LCD Monitors
Exploded View
Figure 3.1 Front Panel
Reference # Button
1
Input Button
Description
Selects the signal to be displayed. Choices are: PC, AV1,
AV2, or S-Video.
2
Menu Button
Selects the on-screen display (OSD).
3
S
Adjusts the value when in
Scrolls up in the OSD.
the OSD.
4
T
Adjusts the value when in
Scrolls down in the OSD.
the OSD or auto adjusts
when in PC mode.
5
W
Decreases the value when in Scrolls left in the OSD.
the OSD.
6
X
Increases the value when in Scrolls right in the OSD.
the OSD.
7
Not Used
8
Power Button / LED Power On (green)
Indicator
Standby (amber)
Unsupported Mode (green)
Power Off (red)
F.01U.078.454 | 1.0 | 2008.03
User’s Manual
Bosch Security Systems, Inc.
General Purpose LCD Monitors
Description | en
11
Figure 3.2 Bottom Panel
Reference #
Connector
Description
1
DC 12 V IN
UML-150-50: 3.3 A
UML-170-50: 4.1 A
UML-190-90: 4.1 A
4
2
D-SUB IN
PC Signal Input
3
VIDEO 1 (AV1) IN
Composite signal input for AV1
4
VIDEO 1 (AV1) OUT
Video looping output for AV1
5
VIDEO 2 (AV2) IN
Composite signal input for AV2
6
VIDEO 2 (AV2) OUT
Video looping output for AV2
7
S-VIDEO (Y/C) IN
Y/C separated signal input
8
S-VIDEO (Y/C) OUT
Y/C separated signal looping output
Description
The Bosch General Purpose Family of LCD monitors display PAL or NTSC standard color
pictures in CCTV systems. Two (2) looping Composite Video BNC connector inputs and one
(1) looping Y/C (S-Video) input using a 4-pin mini-DIN are included with each model. In
addition, each works with a VGA signal.
Monitor control functions are accessed via the front panel push buttons and the multilanguage On-screen Display (OSD). See Figure 3.1 for front panel descriptions.
Bosch Security Systems, Inc.
User’s Manual
F.01U.078.454 | 1.0 | 2008.03
12
en | Installing the Monitor
4.1
General Purpose LCD Monitors
Features
The General Purpose LCD Color Panel Display Monitor Series are designed to display Analog
VGA and Composite Video signals.
4.2
–
15-inch, 17-inch, and 19-inch models
–
100-240 VAC Power Supply
–
NTSC/PAL Auto-Detect
–
High-resolution Display
–
1024 x 768 (UML-150-90)
–
1280 x 1024 (UML-170-90)
–
1280 x 1024 (UML-190-90)
–
VGA Input
–
Composite Video Input
–
Y/C Input (S-Video)
–
On-screen Display (OSD) with Multiple Languages
Power
Model No.
UML-150-90
Rated Voltage
Voltage Range
Power at Rated Voltage
Sync Format
120/230 VAC,
100-240 VAC
25 W (max)
NTSC/PAL
100-240 VAC
40 W (max)
NTSC/PAL
100-240 VAC
45 W (max)
NTSC/PAL
50/60 Hz
UML-170-90
120/230 VAC,
50/60 Hz
UML-190-90
120/230 VAC,
50/60 Hz
5
Installing the Monitor
This chapter outlines the procedures to install the UML-150-90, UML-170-90, or the UML-19090. A qualified service person should install the monitor and adhere to all local codes.
5.1
Ventilation
To prevent overheating, ensure that the ventilation openings on the rear of the monitor are not
covered.
5.2
Mounting the Monitor
The UML-150-90, UML-170-90, and the UML-190-90 are designed for use on a desktop or
mounted to a wall or rack.
5.2.1
Desktop Installation
The Bosch General Purpose monitors are delivered with a 3-pole US-style power cord and a 3pole Euro-style power cord. Use the US-style power cord where 120 VAC, 60 Hz power is
available; use the Euro-style power cord where 230 VAC, 50 Hz power is available. The monitor
automatically adjusts to either power input voltage.
F.01U.078.454 | 1.0 | 2008.03
User’s Manual
Bosch Security Systems, Inc.
General Purpose LCD Monitors
5.2.2
Installing the Monitor | en
13
Wall Mount Installation
The square mounting holes (100 mm [3.9 in.] centers) are compatible with the Bosch UMMLW-20B fixed wall mount or the UMM-LW-30B swivel/tilt. To install the wall mount, do the
following:
1.
Remove the base from the LCD panel section by unscrewing the four (4) holding screws
before separating the base from the panel. NOTE: Save screws for future use.
Figure 5.1 Removing the Base
2.
Mount the unit to the mounting device (not provided) using the four (4) mounting holes
on the rear panel. The square mounting hole patterns are standard on 100 mm (3.9 in.)
centers.
Figure 5.2 Mounting the Device
Bosch Security Systems, Inc.
User’s Manual
F.01U.078.454 | 1.0 | 2008.03
14
en | Installing the Monitor
5.3
General Purpose LCD Monitors
Connecting the Composite Video Signal to the Monitor
There are two (2) BNC connectors located on the rear of the monitor for composite video
input and two (2) BNC connectors for composite video outputs (see Figure 3.2).
NOTE: All video inputs are active loop-through. The impedance is automatically set to 75 ohm
by the input of the signal on the input connector, while operating in a single connection mode
(see Figure 5.5). If a cable is also connected to the output connector, the video signal can be
passed on to another monitor connected to it via the active loop-through function. Up to three
(3) monitors may be connected in this manner (see Figure 5.6).
i
5.4
NOTICE! To select between AV1 and AV2, press Input (Figure 3.1, Item 1) located on the front
of the monitor
Connecting the Y/C (S-Video) Signal to the Monitor
There is one (1) mini-DIN type connector for the S-Video (Y/C) input (see Figure 5.3).
NOTE: Both Y and C inputs are terminated with 75 ohm.
Figure 5.3 Y/C Connection Pinout
5.5
Reference
Input
1
GND
2
GND
3
Y-signal IN or OUT
4
C-signal IN or OUT
Connecting the PC Signal to the Monitor
The monitor can be connected to the analog VGA signal by using the provided VGA cable (DSUB to D-SUB).
Figure 5.4 VGA Input
F.01U.078.454 | 1.0 | 2008.03
User’s Manual
Bosch Security Systems, Inc.
General Purpose LCD Monitors
5.6
Installing the Monitor | en
15
Single / Multiple Monitor Configuration
Figure 5.5 Single Monitor Configuration
Reference #
Description
1
Video Camera
2
VIDEO 1 (AV1) IN
3
VIDEO 1 (AV1) OUT
4
VCR
Figure 5.6 Multiple Monitor Configuration
Reference #
Description
1
Video Camera
2
VIDEO 1 (AV1) IN
3
VIDEO 1 (AV1) OUT
Bosch Security Systems, Inc.
User’s Manual
F.01U.078.454 | 1.0 | 2008.03
16
en | Navigating the Monitor
General Purpose LCD Monitors
6
Navigating the Monitor
6.1
Navigating the Front Panel
Use the front panel to make any necessary OSD adjustments to the UML-150-90, UML-170-90,
or the UML-190-90. See the figure below for an explanation of the front panel.
Figure 6.1 Front Panel Buttons
Reference #
Button
Description
1
Input Button
Selects the signal to be displayed. Choices are: PC,
AV1, AV2, or S-Video.
2
Menu Button
Selects the on-screen display (OSD).
3
S
Adjusts the value when in
Scrolls up in the OSD.
the OSD.
T
4
Adjusts the value when in
Scrolls down in the OSD.
the OSD or auto adjusts
when in PC mode.
W
5
Decreases the value when Scrolls left in the OSD.
in the OSD.
X
6
Increases the value when
Scrolls right in the OSD.
in the OSD.
7
Not Used
8
Power Button / LED
Power On (green)
Indicator
Standby (amber)
Unsupported Mode (green)
Power Off (red)
6.2
Navigating the Monitor On-screen Display (OSD)
The UML-150-90, UML-170-90, and the UML-190-90 have two (2) modes: Video and VGA. The
LCD is programmed through the on-screen display (OSD) menus and submenus where an
operator can select operating parameters. To access the OSD menus, press the Menu button.
Use the front panel of the monitor to make any necessary adjustments to the OSD.
To navigate the set up menus, follow the steps below:
1.
Connect the CVBS or VGA cable.
2.
If required, press the Input button until a signal is displayed. NOTE: Menus are not
available without a signal applied.
3.
Press the Power button to turn on the unit (see Figure 3.1).
4.
Press the Menu button to activate the main menu selections (see Figure 3.1).
5.
Press the
6.
Press the Menu button to enter a selected menu.
F.01U.078.454 | 1.0 | 2008.03
Sand the Tbuttons to select a main menu.
User’s Manual
Bosch Security Systems, Inc.
General Purpose LCD Monitors
Navigating the Monitor | en
17
Wand the Xbutton to toggle the OSD values.
7.
Press the
8.
When finished, scroll to Exit and press the Menu button. Note: If there is no Exit button,
press the Menu button.
6.3
On-screen Display Menus
There are five (5) on-screen menus that allow you to customize your settings. Press the Menu
button to access the OSD menu.
Icon
Menu
Function
Input Source
Enables or disables the input selections. Selects
the video source. Choices are: PC, AV1, AV2, or SVideo.
Screen
Adjusts the Brightness, Contrast, Saturation, Hue,
and the Sharpness level for video performance of
the OSD.
Audio
Not available.
OSD (on-screen display)
Adjusts the H. Position, V. Position, Transparency,
OSD Timer, and Language. Language choices are:
English, French, German, Italian, Dutch, and
Spanish.
Color (PC mode)
Adjusts the color temperature to 9300, 6500, or
user (factory default is 9300).
Not available.
Utility
Enables the user to reset all settings to the factory
default values, and allows the user to lock or
unlock the control key.
Exit
Enables the user to turn on and off the OSD menu,
and displays the following information: horizontal
frequency, vertical frequency, and the firmware
version number.
Bosch Security Systems, Inc.
User’s Manual
F.01U.078.454 | 1.0 | 2008.03
18
6.4
en | Navigating the Monitor
General Purpose LCD Monitors
Video Mode
To access the Input Source submenu, press the Menu button on the front panel of the
monitor, then press the arrows to select the Input Source submenu.
Input Source
Move:
6.5
EXIT: MENU
Screen
To access the Screen submenu, press the Menu button on the front panel of the monitor, then
press the left and right arrows to select the Screen icon. Press the up and down arrows to
select the Screen submenu.
Screen
Brightness
Contrast
Saturation
Sharpness
Move:
EXIT: MENU
Screen
Brightness
Contrast
H. Position
V. Position
Clock Phase
Move:
F.01U.078.454 | 1.0 | 2008.03
EXIT: MENU
User’s Manual
Bosch Security Systems, Inc.
General Purpose LCD Monitors
Navigating the Monitor | en
19
Submenu
Definition
Brightness
Adjusts the brightness level for video performance (range 0-100%).
Contrast
Adjusts the contrast level for video performance (range 0-100%).
Saturation
Adjusts the saturation level for video performance (range 0-100%).
Sharpness
Adjusts the sharpness level for video performance (range 0-100%).
H. Position (PC mode)
Adjusts the horizontal position for the desktop (range 0-100%).
V. Position (PC mode)
Adjusts the vertical position for the desktop (range 0-100%).
Clock
Adjusts the best picture quality by adjusting the horizontal size of
the video displayed (range 0-100%).
Phase
Adjusts for best picture quality by adjusting for sharpness of vertical
lines (range 0-100%).
6.6
Audio
Not available on this monitor.
6.7
OSD
To access the OSD submenu, press the Menu button on the front panel of the monitor, then
press the left and right arrows to select the OSD icon. Press the up and down arrows to select
the OSD submenu.
OSD
H. Position
V. Position
Transparency
OSD Timer
Language
Move:
EXIT: MENU
Submenu
Definition
H. Position
Adjusts the horizontal position for the OSD menu (range 0-100%).
V. Position
Adjusts the vertical position for the OSD menu (range 0-100%).
Transparency
Adjusts the transparency level for video performance (0, 25, 50, and
100% increments).
OSD Timer
Adjusts the on-screen display time (range 5s-20s).
Language
Adjusts the language of the OSD. Choices are: English, French,
German, Italian, Dutch, and Spanish.
Bosch Security Systems, Inc.
User’s Manual
F.01U.078.454 | 1.0 | 2008.03
20
6.8
en | Navigating the Monitor
General Purpose LCD Monitors
Color (PC mode)
To access the Color submenu, press the Menu button on the front panel of the monitor, then
press the left and right arrows to select the Color icon. Press the up and down arrows to
select the Color submenu (range 0-100%).
Color
Color Temp
Red
Green
Blue
9300 K 6500 K
6.9
User
Utility
To access the Utility submenu, press the Menu button on the front panel of the monitor, then
press the left and right arrows to select the Utility icon. Press the up and down arrows to
select the Utility submenu.
Utility
Recall
Lock
Move:
EXIT: MENU
Utility
Recall
AUTO Full Auto
Lock
Move:
F.01U.078.454 | 1.0 | 2008.03
EXIT: MENU
User’s Manual
Bosch Security Systems, Inc.
General Purpose LCD Monitors
Power Management | en
21
Submenu
Definition
Recall
Restores default settings.
AUTO Full Auto
Auto synchronizes the screen to the graphics adaptor. When selected,
displays “Auto in Process...”.
Lock
Locks user from accessing the monitor OSD menus. To unlock, hold
down the menu and up arrow keys together for three (3) seconds.
6.10
Exit
To access the Exit submenu, press the Menu button on the front panel of the monitor, then
press the left and right arrows to select the Exit icon, then press the menu buttons to exit the
OSD.
Exit
H: 63.1KHz
PC
V: 70.0Hz
VER. 1.0
Move:
7
EXIT: MENU
Power Management
These monitors feature a power management system to “power down” upon receipt of the
display power management signaling (DPMS) from a DPMS video card.
To conserve energy and extend monitor life, these monitors automatically start a power saving
mode when the input signal disappears (such as when a PC enters sleep mode). The power
saving mode is active when the LED on the control button panel switches from green to amber
and normal operation resumes automatically when the input signal is restored.
The monitor enters an appropriate mode through identifying each of the three modes of the
signaling system.
7.1
7.2
Power Consumption
Mode
150
170
190
ON
25 W
40 W
45 W
STANDBY
< 5.0 W
< 5.0 W
< 5.0 W
LED Indicator
The power management feature of the monitor is comprised of four stages: On (green),
Standby (amber), Unsupported mode (green), and Power Off (red).
Bosch Security Systems, Inc.
User’s Manual
F.01U.078.454 | 1.0 | 2008.03
22
en | Trouble Shooting Guide
8
General Purpose LCD Monitors
Trouble Shooting Guide
Problem
Solution
No image is displayed on screen
–
Check that the power cord of the monitor is securely connected into the
wall outlet or grounded extension cable or strip.
–
Power switch should be in the ON position and the LED lit.
–
Check that the Brightness and/or Contrast adjustments of the display have
not been turned down to minimum levels.
“Check Input Signal” message is
–
The signal cable should be completely connected to the video card/
–
The video card should be completely seated in its slot and the computer
displayed in PC mode
computer.
switched ON.
Display image is not centered, is
Push the down key to activate the Autoset function.
too small, or too large in the PC
mode
Vertical or horizontal noise is
Adjust the Clock and Phase in the OSD submenu.
present in the picture
Incorrect colors
–
Press the Menu button on the front panel of the monitor, then press the
right arrow to select the Color menu. Press the down arrow on the front
panel and select 9300K or 6500K.
- or -
–
Press the Menu button on the front panel of the monitor, then press the
right arrow to select the Utility menu. Press the down arrow on the front
panel and select Recall to reset to the default settings.
The error message “Unsupport
PC is operating with either a resolution or timing mode that is not supported.
Mode” is displayed
Change the PC timing mode to one of the valid combinations below:
Timing mode
640 x 480; 60/72/75 Hz
800 x 600; 60/72/75 Hz
1024 x 768; 60/70/75 Hz
1280 x 1024; 60/75 Hz
9
Maintenance
To clean the LCD panel, wipe off water droplets or oil immediately with absorbent cotton or a
soft lint-free cloth. Staining and discoloration may occur if left on the panel for long periods.
If the surface (polarizer) of the LCD panel is dirty or stained, use absorbent cotton or a soft
lint-free cloth to remove the residue as follows:
1.
2.
Turn off the computer or display.
Do not spray any liquid directly on the screen. Dampen a clean, soft, lint-free cloth with
water only (using a paper towel or dirty cloth can scratch the screen).
3.
Gently wipe the screen starting from the top of the screen to bottom wiping in a
downward motion. Be careful not to press too hard to avoid damaging the screen.
4.
i
To avoid streaking, wipe the screen again with another clean, dry, lint-free cloth.
NOTICE! If water does not work, use a mild cleaner labeled for use with LCD panels, available
at office supply stores.
F.01U.078.454 | 1.0 | 2008.03
User’s Manual
Bosch Security Systems, Inc.
General Purpose LCD Monitors
Maintenance | en
23
Do not use any of the following as a cleaning agent:
–
Ketone type materials
–
Ethyl alcohol
–
Ethyl acid
–
Toluene
–
Methyl chloride
–
Ammonia
Use of these materials may permanently damage the polarizer due to a chemical reaction.
Bosch Security Systems, Inc.
User’s Manual
F.01U.078.454 | 1.0 | 2008.03
24
en | Technical Specifications
10
General Purpose LCD Monitors
Technical Specifications
UML-150-90
UML-170-90
UML-190-90
Electrical
Rated Voltage
120/230 VAC, 50/60 Hz
120/230 VAC, 50/60 Hz
120/230 VAC, 50/60 Hz
Voltage Range
100-240 VAC
100-240 VAC
100-240 VAC
Power at Rated Voltage
25 W operation, 5 W standby 40 W operation, 5 W standby 45 W operation, 5 W standby
Sync Format
PAL/NTSC
PAL/NTSC
PAL/NTSC
LCD Panel
TFT LCD
TFT LCD
TFT LCD
Screen Size (H x V)
304.1 x 228.1 mm
338.0 x 270.0 mm
376.0 x 301.0 mm
(12.0 x 9.0 in.)
(13.3 x 10.6 in.)
(14.8 x 11.9 in.)
15 in. (381 mm) measured
17 in. (432 mm) measured
19 in. (483 mm) measured
diagonally
diagonally
diagonally
0.297 x 0.297 mm
0.264 x 0.264 mm
0.294 x 0.294 mm
(0.01 x 0.01 in.)
(0.01 x 0.01 in.)
(0.01 x 0.01 in.)
1024 x 768 pixels, 400 TV
1280 x 1024 pixels, 400 TV
1280 x 1024 pixels, 400 TV
lines typical
lines typical
lines typical
Aspect Ratio
4:3
5:4
5:4
Display Colors
16.2 million colors
16.2 million colors
8-bit interface; 16.7 million
Viewable Picture Area
Pixel Pitch (H x V)
Resolution
colors
Response Time
< 12 ms
< 5 ms
5 ms
Backlight
Two (2) cold cathode
Two (2) cold cathode
Four (4) cold cathode
fluorescent tubes, rated life fluorescent tubes, rated life fluorescent tubes, rated life
50,000 hours
50,000 hours
50,000 hours
LCD Panel Optical Characteristics
Luminance
250 cd/m, anti-glare, hard-
300 cd/m, anti-glare, hard-
300 cd/m, anti-glare, hard-
coating treatment
coating treatment
coating treatment
Contrast Ratio (CR)
450:1
1000:1
800:1
Viewing Angle
130°/110°
160°/160°
160°/160°
(Horizontal/Vertical)
Video Input
Composite Video (CVBS) 1.0 Vp-p (0.5–1.5 Vp-p), automatic switching from 75 W unbalanced termination to Hi-Z
with passive loop-through operation
Y/C (S-video)
F.01U.078.454 | 1.0 | 2008.03
0.7 Vp-p (Y-signal), 0.3 Vp-p (C-signal), 75 W termination
User’s Manual
Bosch Security Systems, Inc.
General Purpose LCD Monitors
Technical Specifications | en
25
PC Input
Analog RGB
0.7 Vp-p (0.5–1 Vrms)
PC Timing Modes
640 x 480
60/72/75 Hz
60/72/75 Hz
60/72/75 Hz
800 x 600
60/72/75 Hz
60/72/75 Hz
60/72/75 Hz
1024 x 768
60/70/75 Hz
60/70/75 Hz
60/70/75 Hz
60/75 Hz
60/75 Hz
1280 x 1024
Controls
Front Panel
Push-buttons
Input
Selects: Video1, Video2, S-video, VGA
Menu
Selects on-screen display (OSD), up cursor, down cursor/auto adjust, left cursor, right
cursor
Power
On/Off
Front Panel Lockout
Multiple push-button combination
On-screen Display
Video Mode
Input Source, Screen, OSD, Utility
PC Mode
Input Screen, OSD, Color, Utility
Indicators
LED
Power On (green)
Standby (amber)
Unsupported Mode (green)
Power Off (red)
On-screen
VGA: Check input signal
Video: Flashes “AV1” or “AV2” when there is a black screen
Connectors
Video 1 (AV1)
Composite video: two (2) BNC (1 in, 1 out)
Video 2 (AV2)
Composite video: two (2) BNC (1 in, 1 out)
Y/C (S-video)
Two (2) mini-DIN, 4-pin (1 in, 1 out)
RGB
One (1) VGA cable included
Power Input
5.5 mm DC input jack
Power Adapter
Input: 100–240 VAC, 50/60 Hz
Input: 100–240 VAC, 50/60 Hz Input: 100–240 VAC, 50/60 Hz
(included)
Output: 12 VDC, 3.3 A
Output: 12 VDC, 4.1 A
Bosch Security Systems, Inc.
User’s Manual
Output: 12 VDC, 4.1 A
F.01U.078.454 | 1.0 | 2008.03
26
en | Technical Specifications
General Purpose LCD Monitors
Mechanical
Cabinet Material
ABS plastic
Finish
Black
Mount
Wall mounting compatible with standard bracket, 100-mm centers, M4 thread
Dimensions (W x H x D)
Monitor with Base
352 x 355 x 200 mm
382.4 x 390.5 x 200.0 mm
430 x 428 x 200 mm
(13.86 x 14.0 x 7.9 in.)
(15.1 x 15.4 x 7.9 in.)
(16.9 x 16.9 x 7.9 in.)
352 x 292 x 58 mm
382.4 x 330.0 x 58.7 mm
420 x 374 x 60 mm
(13.9 x 11.5 x 2.2 in.)
(15.1 x 13.0 x 2.3 in.)
(16.9 x 14.7 x 2.4 in.)
Monitor with Base
3.7 kg (8.1 lb)
6.6 kg (14.6 lb)
7.6 kg (16.9 lb)
Monitor Only
2.5 kg (5.6 lb)
4.1 kg (9.05 lb)
5.9 kg (13.1 lb)
Monitor Only
Weight
Environmental
Operating Temperature 0°C to 40°C (32°F to 104°F)
Storage Temperature
–20°C to 60°C (–4°F to 140°F)
Humidity
Maximum 90%, non-condensing
Parts Included
One (1) Bosch General Purpose Color LCD Flat Panel Monitor
One (1) VGA to VGA cable
Two (2), 3-wire power cords with a grounded plug: one (1) with a European/Continental plug type and one (1) with
a U.S. plug type
F.01U.078.454 | 1.0 | 2008.03
User’s Manual
Bosch Security Systems, Inc.
Americas
Bosch Security Systems, Inc.
850 Greenfield Road
Lancaster, Pennsylvania 17601
USA
Telephone +1 888-289-0096
Fax
+1 585-223-9180
Email: security.sales@us.bosch.com
www.boschsecurity.us
Europe, Middle East, Africa:
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven, The Netherlands
Phone: + 31 40 2577 284
Fax: +31 40 2577 330
emea.securitysystems@bosch.com
www.boschsecurity.com
Asia-Pacific:
Bosch Security Systems Pte Ltd
38C Jalan Pemimpin
Singapore 577180
Phone: +65 6319 3450
Fax: +65 6319 3499
apr.securitysystems@bosch.com
www.boschsecurity.com
© Bosch Security Systems, 2008; F.01U.078.454 | 1.0 | 2008.03; Data subject to change without notice.