Makita UM40LDW Instruction manual

16" (406 mm) MODEL UM40lDW
Convertlble Rear Bag I Mulching
With Charger
INSTRUCTION MANUAL
SPECIFICATIONS
Model UMlOlD
II
Effective cutting width
No load Speed fRPM1
16" (406 m m )
3.800
Dimensions IL
Voltage
24v
I
x W x HI
51 3/4" x 19" x 39 314
I1 316 mm x 482 m m x 1 010 mml
Input
output
A C 120V60Hz
D C 24V
Net weight
70
Ibs
13'
kgl
Charging time
Approx
4 Hrs
Manufacturer reserves the right t o change speclfications without notice
Note SDecifications mav differ from countrv to countrv
CAUTION
IMPORTANT
The Lawn Mower Makita Model UM401D employs sealed lead acid batteries Be sure to follow
the following instructions t o charge it
1 I Charge the mower immediately after purchase
21 Always recharge the mower after each use without fail
31 Be sure t o charge the mower every six months, when n o t using it for long periods If l e f t
uncharged, i t may become unchargeable
WARNING
Read the important safety instructions
For your personal safety, READ and UNDERSTAND before using
Use only the Makita battery
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
IMPORTANT
SAFETY INSTRUCTIONS
(For Gardening Appliances)
WARNING: WHEN USING CORDLESS TOOLS, BASIC
SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO
REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND
PERSONAL INJURY, INCLUDING THE FOLLOWING:
SAVE THESE INSTRUCTIONS.
READ ALL INSTRUCTIONS.
1 . Avoid Dangerous Environment - Don't use appliances in damp or wet
locations.
2. Don't Use In Rain.
3. Keep Children Away - All visitors should be kept at a distance from work area.
4. Dress Properly - Do n o t wear loose clothing or jewelry. They can be caught
in moving parts. Use of rubber gloves and substantial footwear is recommended when working outdoors. Wear protective hair covering t o contain
long hair.
5. Use Safety Glasses - Always use face or dust mask i f operation is dusty.
6.Use Right Appliance - Do n o t use appliance for any job except that for which
i t is intended. Use only for grass cutting.
7. DO NOT INSERT KEY INTO MOWER UNTIL IT IS READY TO BE USED.
8. Avoid Unintentional Starting - Don't carry plugged-in appliance w i t h finger
on switch. Be sure s w i t c h is o f f w h e n plugging in.
9. Don't grasp the exposed cutting blades or cutting edges when picking up
or holding the appliance.
IO. Don't Force Appliance - It will do the job better and w i t h less likelihood of
a risk of injury at the rate for which it was designed.
1 1 . Don't Overreach - Keep proper footing and balance at all times.
12. Physical Condition - Do not operate mower while under the influence of drugs,
alcohol, or any medication.
13. Stay Alert - Watch w h a t you are doing. Use common sense. Do not operate
appliance when you are tired.
14.Store Idle Appliances Indoors - When not in use, appliances should be stored
indoors in dry. and high or locked-up place
-
out of reach of children.
15. Maintain Appliance W i t h Care - Keep cutting edge sharp and clean for best
performance and t o reduce the risk of injury. Follow instructions for lubricating and changing accessories. Inspect charger cord periodically, and if
2
damaged, have it repaired by an authorized service facility. Inspect extension
cords periodically and replace if damaged. Keep handles dry, clean, and free
from oil and grease.
16. Remove Adjusting Wrenches. Form habit of checking t o see that adjusting
wrenches are removed from mower before turning it on.
17. Check Damaged Parts - Before further use of the appliance, a guard or other
part that is damaged should be carefully checked t o determine that it will
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and any
other condition that may affect its operation. A guard or other part that is
damaged should be properly repaired or replaced by an authorized service
center unless indicated elsewhere in this manual. When servicing, use only
identical replacement parts.
18. Keep guards in place and in working order.
19. Keep hands and feet away from rotating blades. Caution - Blades coast after
turn off.
20. Remove key before servicing, cleaning or removing material from the
gardening appliance.
21. Use only Makita genuine blades specified in this manual.
22. Check the blades carefully for cracks or damage before operation. Replace
cracked or damaged blades immediately.
23. Remove foreign matters such as rocks, wire, bottles, bones and large sticks
from the work area before cutting t o prevent personal injury or damage to
the appliance.
24. When stopping operation or before carrying the tool, always switch it off
and wait until the blades come t o a complete stop. Carry the tool w i t h the
blades in front and away from you.
25. Stop operation immediately if you notice anything abnormal. Switch off the
appliance and remove the key from the appliance. Then inspect the appliance.
26. NEVER ATTEMPT TO MAKE WHEEL HEIGHT ADJUSTMENTS WHILE
MOWER IS RUNNING.
27. RELEASE SWITCH LEVER AND WAIT FOR BLADE ROTATION TO STOP
BEFORE CROSSING DRIVEWAYS, WALKS, ROADS, AND ANY GRAVELCOVERED AREAS. Also remove key if you leave it, reach t o pick-up or move
something out of your way, or for any other reason that may distract you
from what you are doing.
28. Objects struck by the lawn mower blade can cause severe injuries to persons.
The lawn should always be carefully examined and cleared of all objects prior
t o each mowing.
29. If lawn mower strikes a foreign object, follow these steps:
I ) Stop lawn mower. Release the switch lever.
II 1 Remove key.
3
111 1 Inspect for damage.
I V ) Repair any damage before restarting and operating the lawn mower.
30. CHECK THE REAR BAG FREQUENTLY FOR WEAR OR DETERIORATION. For
storage, always make sure the rear bag is empty. Replace a worn bag w i t h
a new factory replacement bag for safety. Order Part No. 1 6 6 0 4 5 9
31. Stop the motor and remove key whenever you leave the equipment, before
cleaning the mower housing, and before making any repairs or inspections.
32. M o w across the face of slopes, never up and down. Exercise extreme caution when changing direction on slopes. Do not m o w excessively steep
slopes.
3 3 . Do n o t wash w i t h a hose; avoid getting water i n motor and electrical
connections.
34. Check the blade mounting bolt at frequent intervals for proper tightness.
3 5 . Keep all nuts, bolts, and screws tight t o be sure the equipment is in safe
working condition.
36. Keep blades sharp.
MEETS CPSC SAFETY REQUIREMENTS
Makita mowers conform t o the safety standards of the American National
Standards Institute, and the US. Consumer Product Safety Commission. The
Blade turns when the motor is running.
4
IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERIES & CHARGER
I . SAVE THESE INSTRUCTIONS - This manual
contains important safety and operating instructions for battery charger.
2.Before using battery charger, read all instructions and cautionary markings
on (1) battery charger and (2)product using battery.
3. CAUTION - To reduce risk of injury, charge ONLY MAKITA type rechargeable
batteries used in Model UM401D. Other types of batteries may burst causing
personal injury and damage.
4. Do not expose charger t o rain or snow.
5. Use of an attachment not recommended or sold by the battery charger
manufacturer may result in a risk of fire, electric shock, or injury t o persons.
6. To reduce risk of damage t o electric plug and cord, pull by plug rather than
cord when disconnecting charger.
7. Make sure cord is located so that it will not be stepped on, tripped over, or
otherwise subjected t o damage or stress.
8.A n extension cord should not be used unless absolutely necessary. Use of
improper extension cord could result i n a risk of fire and electric shock. If
extension cord must be used, make sure:
a. That pins on plug of extension cord are the same number, size, and shape
as those of plug on charger;
b. That extension cord is properly wired and in good electrical condition; and
c. That wire size is at least as large as the one specified in the table below.
TABLE 1
RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS FOR BATTERY CHARGERS
I Length of Cord (Feet) I
I A W G S i z e o f Cord
I
25
1
50
I 100 I 150 I
18
I
18
1
18
I
16
1
9. Do not operate charger with damaged cord or plug - replace them immediately.
IO. Do not operate charger if
it has received a sharp blow, been dropped, or
otherwise damaged in any way; take it t o a qualified serviceman.
1 1 . Do not disassemble charger or product which contains battery; take it t o
a qualified serviceman w h e n service or repair is required. Incorrect
reassembly may result in a risk of electric shock or fire.
12.To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk.
5
ADDITIONAL SAFETY RULES
FOR BATTERIES IN MOWER
1. Use ONLY the Makita charger Model DC240 specified t o charge the Makita
model UM4OlD.
2. Do not short the battery:
1) Do not touch the charging inlet w i t h any conductive material.
2) Shut the cover on the charging inlet when not charging.
3)Do not expose mower t o water or rain.
A battery short can cause a large current flow, overheating, possible burns
and even a breakdown.
3.Do not leave mower exposed t o direct sunlight. Do not store mower in locations
where the temperature may reach or exceed 40° C ( 1 0 4 O F).
4. Batteries in Makita Model UM401D contains a strong electrolyte (dilute sulfuric
acid). Do not apply undue force t o the batteries, drop or strike them. Do not
attempt t o disassemble or make modifications t o the batteries.
5. I f the batteries break open and electrolyte (dilute sulfuric acid) contacts skin
or clothing, wash immediately w i t h running water. If electrolyte gets into your
eyes, rinse them out w i t h clear water and seek medical attention right away.
6. As Service life of the batteries ends, their capacity and operation time
decrease. Contact your nearest Makita Service Center or Distributor t o replace
them w i t h new batteries.
7. When replacing batteries, all batteries should be replaced at the same time.
Mixing fresh and discharged batteries could increase internal cell pressure and
rupture the discharged battery.
8. When inserting batteries into this product, the proper polarity or direction must
be observed. Reverse direction of batteries can result in leakage or explosion.
9. Never expose mower or batteries t o flames, fire or great heat. Breakage may
cause release of injurious material.
TIPS FOR MAINTAINING MAXIMUM RUN
PERFORMANCE AND BATTERY LIFE
1. Charge the mower immediately after purchase.
2. Always recharge the mower after each use without fail.
3.We recommend that you leave the charger connected t o the mower even after
the charging cycle is complete. The charger will switch into its "maintenance
charge (trickle charge)" mode and keep the battery fresh and fully charged.
4. Be sure t o charge the mower every six months, when not using it for long
periods. If left uncharged., it may become unchargeable.
6
ADDITIONAL SAFETY RULES FOR CHARGER
1. The Makita charger Model D C 2 4 0 is specifically designed t o charge only
the Makita batteries used in Model UM401D. D o not attempt t o charge any
other battery with this charger.
2. Handle the charger carefully. Do not drop or strike it.
3. Never carry the charger by cord or yank it t o disconnect from receptacle.
4. Keep cord from heat, oil, chemicals, and sharp edges.
5. Use only a power source of the same voltage as indicated on the nameplate
of the charger w h e n charging.
6. Do not attempt t o use a step-up transformer, an engine generator, a DC-AC
inverter or DC power receptacle.
7. Charge mower at a room temperature between 5 O C ( 4 1 O F) and 40° C
( 1 0 4 O F).
8. Do not charge in place exposed t o direct sunlight.
9. Do not charge lawn mower i n rain, or in wet locations.
10. Do not allow the charger t o get wet.
11. Do not charge inside a box or container of any kind.
12. Do not charge near volatile, flammable material such as gasoline, paint, gas,
adhesive, etc.
13. Do not charge on top of paper, carpet, vinyl sheeting, cloth materials, etc.
14. D o not allow anything t o cover or clog the charger vents. Do not attempt
t o insert anything into the vents.
15. Do not touch the charger w i t h wet hands.
16. D o not charge i n dusty place.
17. Stop charging immediately if you notice anything abnormal. Ship or take the
charger and the mower t o your nearest Makita Service Center or Distributor
for checking them.
18. Do not attempt t o disassemble or make modifications t o the charger.
19. Do not put any metal object or foreign matter into the charging plug. Shortcircuit will occur, causing a burn injury and charger breakdown.
20. This charger incorporates parts such as switches and relays that are likely
t o produce arcs or sparks; therefore, when charging mower in a garage or
similar location, locate the charger in a room or enclosure provided for this
purpose.
SAVE THESE INSTRUCTIONS.
7
Unpacking
Your mower has been completely assembled at the factory except for the rear bag.
1. Remove the rear bag, instruction manual, charger and plastic bag containing accessories from the carton.
2. Remove the mower from the carton and place all four wheels on the ground or,floor.
3. Check the carton thoroughly and make sure there are no loose parts.
4. To unfold the handle, raise it into place. Fit the protrusion of the handle into one of
the square holes in left and right sides of the mower, and then secure the handle by
tightening the clamp nuts.
Clamp nut
/
Charging
*Remove the key from the mower (slide it
Inlet cover
to your left and pull out) and store it in a
Key I
-Charging
inlet
safe place - out of the reach of children.
*Open the inlet cover and insert the charging plug into the inlet. (REMEMBER: The
charging inlet has polarity. DO NOT DAMAGE OR ABUSE THE PLUG AND INLET.)
*Then plug the charger into the power
source. The charging light will turn on in
green color, and immediately the color of
the charging light will change to red and
charging will begin. The charging light will
remain lit steadily during charging.
*When the charging light color changes
from red to green, <he charging is complete. Charging takes approx. 4 hours
*After charging, unplug the charger from the power source and pull out the charging plug
from the charging inlet.
I
8
NOTE
*If the charging light flashes in green color, the charging plug may not be inserted into the
charging inlet correctly Check the charging plug and charging inlet
*If the charging light flashes in red color the batteries are too weak for normal charging
Wait for a while until normal charging starts after recovery charging is finished
*If the mower has not been used for long periods. it will take more than specified time to
charge the mower
*If the mower is left uncharged for more than six months, it may become unchargeable
*The indicator does not indicate progress during charge cycle
CAUTION
Any of the following conditions indicates damages to the charger and/or batteries Unplug
the charger from power source and disconnect the charging plug immediately Have them
checked by your nearest Makita Authorized or Factory Service Center
1) The charging light remains flashing in green color (does not change to red), although the
charging plug is correctly inserted into the charging inlet
2) The charging light color does not change to green in more than 5 hours after you start
charging
3) The charging light does not light up or flash in any colors while power is supplied
4) The charging light flashes alternately in green and red color (Probably the batteries are
worn out or damaged )
Handle adjustment
1. Turn off the interlock switch and remove
the key. If you are recharging the
mower, stop recharging and disconnect
the charging plug
2 Loosen the clamp nuts on the left and
right sides
3 Fit the protrusion of the handle into one
of the three square holes according to
your preference
4 Tighten the clamp nuts firmly to secure
the handle
CAUTION
Always tighten the clamp nut on the left and right sides Failure to do so may cause
the handle to come loose unexpectedly during operation. resulting in serious injury to
operator
9
Wheel height adjustment (six steps between 1" and 3-1/2" or 25 mm and 89 mm).
1. Turn off the interlock switch and remove
the key. If you are recharging the
mower, stop recharging and disconnect
the charging plug.
2. Push the lever outward and fit it into one
of the grooves for your desired cutting
height. This one touch wheel height
adjustment system can adjust all four
wheels at the same time.
CAUTION:
Always make sure that the lever is fit in the groove properly before operation.
Installing or removing blade
WARN ING :
*Always turn off the interlock switch and remove the key before installing or removing the
blade. If you are recharging the mower, stop recharging and disconnect the charging plug
*The blade coasts for several seconds after the switch is turned off. Always remove the
blade after it has come to a complete stop.
1. Wear gloves.
2. Turn the mower on its side to expose the blade.
3. Hold the blade holder with 32 mm wrench so that the other end of 32 mm wrench will
contact the underside of mower deck. Hold the hex bolt with 13 mm socket wrench
and turn it lightly counterclockwise until the 32 m m wrench is firmly held by the underside of mower deck.
4. To loosen the hex bolt, turn the 13 mm socket wrench counterclockwise while holding
down its top.
5. Remove the hex bolt, cup spring and blade. Be sure to remember the removal procedures.
6. To install the blade, follow the removal procedures in reverse. Be careful not to install it
upside down. When installing the blade, always make sure that the end of blade holder
fits in the cup spring.
7. Tighten the hex bolt firmly with the wrenches provided. To tighten it, turn the 13 mm
socket wrench clockwise while holding down its top. When doing so, the 32 mm
wrench should be firmly held by the underside of mower deck.
I
Deck
I
17/32" (1 3 mml
socket wrench
I
=Blade
holder
Cup spring
1-WZ"132 mml wrench
10
k-
Hex flange
head bolt
ME x 30
WARNING:
Replace bent or damaged blade immediately. A bent or damaged blade may cause excessive vibration, resulting in damage to the mower or serious injury to operator.
Blade sharpening
Keep the blade sharp and clean for best performance. A dull blade does not cut grass
cleanly and evenly. It may overload the motor and waste more battery energy
1. Turn off the interlock switch and remove
the key. If you are recharging the
mower, stop recharging and disconnect
the charging plug.
2. Remove the blade as described in
“Installing or removing blade”.
3. Secure the blade in a vice or the like.
4. Carefully sharpen the cutting edges of
the blade with a file or sharpening stone.
5. Check the balance of the blade as
described in ”Blade balancing”.
6. Install the blade and secure it by tightening the bolt with the wrenches provided.
File or sharpening store
7
CAUTION:
*Wear gloves and safety glasses during sharpening
*Make sure the blade remains balanced.
*Sharpen the blade at the original cutting angle.
*Sharpen the cutting edges on both end of blade, removing equal amounts of material
from both ends.
1. Secure a screwdriver horizontally in a vice.
2. Place the center hole in the blade on
screwdriver shank.
3. If the blade is balanced, it will remain in a
horizontal position.
4. If either of the blade drops downward,
sharpen the heavy side until the blade is
balanced.
‘
11
Emptying rear bag
1. Release the switch lever.
2. Turn off the interlock switch and remove the key
3. Open the rear guard.
4. Hold the rear bag handle and remove the rear bag from the mower.
5 . Empty the grass from the rear bag.
Rear guard
-
Rear bag
WARNING:
To reduce risk of injury, inspect rear bag frequently and replace with recommended
replacement if there are signs for wear or deterioration.
Installing mulching plate
1. Turn off the interlock switch and remove the key. If you are recharging the mower, stop
recharging and disconnect the charging plug.
2. Turn the mower on its side to expose the blade.
3. Install the two protrusions of the mulching plate into the holes in the deck. Push the
mulching plate into the discharge opening until the hook of the mulching plate is held by
the undercover. Open the rear guard and make sure that the hook of the mulching plate
is properly held by the undercover.
WARN ING :
Always install the mulching plate when operating the mower with the rear bag removed.
I
12
Mulching
While mulching, your new mower is designed to cut the grass clipptngs into small pieces
and distribute them back into the lawn. Under normal conditions, the mulched grass will
biodegrade quickly to provide nutrients to the lawn.
Please review the following recommendations for optimum mulching performance.
1. Avoid mowing when the grass is wet from rain or dew. Wet grass may from clumps
which interfere with the mulching action and reduce run-time. The best time to mow
grass is in the late afternoon when the grass is dry and the newly cut area will not be
exposed to direct sunlight.
2. For best mulching performance, set the cutting height to remove about one third of
the grass blade length, ideally no more than 1-1/2" at one time. If the lawn is overgrown, it may be necessary to increase the cut height to reduce the pushing effort and
prevent overloading the motor. For extremely heavy mulching, it is advisable to first cut
at a high cut height setting, and then recut to the final cut height. Otherwise, make
narrower cuts and mow slowly.
3. For best performance, keep the mower housing free of built-up grass. From time to
time turn off mower and wait for the blade to come to a complete stop. Then unplug
the key and turn mower on its side. Using an object such as a stick, wipe out any accumulation of grass in the blade area. Be careful of the sharp edges of the blade. Clean
often in wet, spring grass, and always after every use.
4. Certain types of grass or grass conditions may require that an area be mulched a
second time to fully disperse the grass throughout the lawn. If cutting a second time, it
is advisable to cut perpendicular (across) the first cut pattern. DO NOT CHANGE CUT
PATTERN IN ANY WAY THAT WOULD CAUSE MOWING DOWN A HILL.
5. Change your cutting pattern from week to week. This will help prevent matting and
graining of the lawn.
Switch action
This mower is equipped with the interlock switch and handle switch. If you notice anything
abnormal with either of these switches, stop operation immediately and have them
checked by your nearest Makita Authorized or Factory Service Center.
1. Insert the key into the interlock switch.
2. Slide the key to turn on the interlock switch.
3 Depress the switch button
r
Interlock switch
\lndicatoi
Key
13
4 Pull the switch lever toward you while depressing the switch button
5 Release the switch button as soon as the motor starts running The mower will continue to run until you release the switch lever
6 The indicator indicates remaining capacity of the battery only when the motor is running
7 Release the switch lever to stop the motor
8 When not in use, turn off the interlock switch and remove the key Store the key in a
safe place out of reach of children
Overload protector
This mower is equipped with an overload
protector which automatically cuts out to
break the circuit whenever heavy work is
prolonged. When it cuts out, turn off the
interlock switch and remove the key.
Inspect the blade for damage or something
wrong. After making sure that there is nothing wrong with the mower, push the restart
button to resume operation.
Time on charge
1 Hour
3 Hours
4 Hours
14
YO of full charge
2 5 Yo
75 96
FULL
Restart button
Run time
20 Minutes
55 Minutes
75 Minutes
Maintenance & Storage
1. REMOVE KEY. Store it in a safe place out of the reach of children.
2. Clean your mower using only mild soap and a damp cloth. Do not spray or pour water
on your mower when cleaning.
3. Turn mower on its side and clean grass clippings that have accumulated on the underside of mower deck.
4. Check all nuts, bolts, knobs, screws, fasteners, etc. for tightness.
5. Inspect moving parts for damage, breakage, and wear. Have repairs made on any damaged or missing parts.
6. Recharge the batteries to a full charge. Do not store mower with discharged batteries. Battery failure will occur in a very short time if mower is stored without having a
full charge. We recommend that you charge batteries continuously while in storage and
during the off season.
7. Store mower indoors in a cool, dry place. Don’t store the mower and charger in locations where the temperature may reach or exceed 40°C (104°F).
CAUTION:
Always be sure that charger is unplugged and disconnect DC output plug from the mower
before attempting to perform inspection or maintenance.
To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should
be performed by Makita Authorized or Factory Service Centers, always using Makita
replacement parts.
Recycling the batteries
Caution:
The product you have purchased contains a rechargeable battery. The battery is recyclable.
At the end of its useful life, under various state and local laws, it may be illegal to dispose
of this battery into the municipal waste stream. Check with your local solid waste officials
for details in your area for recycling options or proper disposal.
1s
ACCESSORIES
CAUTION
These accessories or attachments are recommended for use with your Makita tool specified in this
manual The use of any other accessories or attachments might present a risk of injury to persons
The accessories or attachments should be used only in the proper and intended manner
*Charger
Model DC240
*Mulching plate
Part No. 416211-1
*Wrench 32
Part No. 781028-4
16
*Swing arm blade
Pan No. 72901 1-5
*Socket wrench 13
Pan No. 782226-3
Dec-19-'96
US
16" (406 mm)
CORDLESS LAWN MOWER
Model UM401DW
17
Note: The switch and other part configurations
may differ from country to country.
18
MODEL U M 4 O l D W
izD
Dec-19-
96 US
DESCRIPTION
M
MACHINE
X
E
~
58
1
Torsion Spr8ng 20
59
60
61
62
1
LeVOI
7
4
8
9
IO
1
1
2
Tapping Screw 41 I 8
CDWhng Complete
Tapping Screw Flange 4x25
Tapping Screw 4 r 18
Flat Washer 4
TenSlOn Sprlnp 1 2
Her Lock Nul M6- IO
Deck
Rear Shall
Flat Washer IO
67
1
11
2
Flat Washer 10
68
2
ComDreSrlon SD"ng 16
Switch Bunon
Tension Spring 5
Switch
Switch 801 Cover
Tapping Screw 4 ~ 1 8
12
2
8
69
1
Slra!" Aellel
13
14
15
16
2
Bolt 3/B 16UNC
Wheel Cap
Hex Flange Head Bolt M a x 3 0
Coned Disc Spring 14
Blade Holder
Hex Bolt M6x4O
Swing Arm Blade 4 0 6
Hex Socket Head Screw M a x 8
oust Cover
Wheel Cap
Boll 318- 16UNC
Fix Plate
FIX Plate
Band
Hex Boll M 5 1 5
Bearing Box
Ball Bearing 6203LL8
Flat Washer 17
Plate
Carbon Brush
Flat Washer 4
Tapplng Screw Flange PT 4 r 12
Yoke Unit
Tapplng Screw 4 x 1 8
Stram Relief
70
71
72
73
74
15
76
17
1
Cord Unit
Switch Box
1
1
5
6
1
1
2
1
1
1
4
17
18
19
20
21
22
23
24
1
1
1
2
2
1
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
2
I
1
1
2
1
1
1
1
2
2
2
1
2
1
2
1
1
1
1
4
4
1
1
2
4
8
I
2
2
2
1
1
63
64
65
Tapping Screw Flange PT 5125
Battery Holder Complete
End Bell
Ball Bearing 6 0 0 0 L L 8
MOTOR ASSEMBLY
IWlfh Item 27 - 3 5 4 0 & 411
Connecting Rod
Thermal Cut 011 Complete
Hex N u l M 5
Hex Bolt M 5 r 1 2
8aflWy COmpkte
Battery COmpkIe
Rereining Ring 5 - 8
Plate
Tapping Screw 4x18
Front Shaft
Flat Washer 1 0
Flat Washer I O
7 Wheel
Handle Curhion
Swslch Lever
Note The switch and other part
ZDeCifiCaIiOnS
Thin Washer 1 5
1
Stop Ring
1
I
1
Insulalmn Label
1
66
Wheel
1
1
1
4
1
1
1
E
~
I2
Tapping S c r e w 4 x 1 8
Name Plate
Switch Lever A r m
1
Handle
Wing Nul M 8
Rear Guard Shall
Torsla" sprang 8
Rear Guard Complete
Rear 889 Cover Complete
Rear Bag Rod
Rear Bag
Tapping Screw 4x18
Height Adluster Complete
Under Cover
Tapping Screw 4x18
Under Guard
Handle Holder 1
Holder Plare
Pan Head Screw M 4 r l 2
Flat Washer 4
Tapplng Screw 4x18
Hex Bolt M8x50
Shall Holder
TaDDlng Screw 4x18
Hex 801, M a x 5 0
Handle Holder R
Relay
Tapping Screw 4x18
Wing Nul M8
Indicator
Tapping Screw Flange PT 4x12
Switch
Switch Plate
Band
Torsion Spring 4
101
1
Inlet c o v e r
108
109
2
Tapping Screw Flange PT 5x25
110
1
Cap
1
1
2
1
78
79
80
81
1
1
1
82
83
2
84
85
1
86
87
3
1
88
1
1
89
6
YO
6
3
3
1
2
2
1
1
1
1
1
1
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
2
I
1
1
1
Spring Pl" 3 - 2 8
Control Panel Sei lWiIh Item 1 131
Inlet
Control Panel Set IWilh Item 1 I 1 I
Current Relay
may differ from country lo country
19
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to
be free of defects from workmanshlp and materials for the period of ONE YEAR from the date of
originid purchase. Should any trouble develop during this one-year period, return the COMPLETE
tool, freight prepaid, t o one of Makita’s Factory or Authorized Service Centers. If inspection shows
the trouble is caused by defective workmanship or material, Makita will repair (or at our option,
replace) without charge.
This Warranty does not apply where:
repain have been made or attempted by others:
repairs arc required because of normal wear and tear
The tool h w been abused, misused or improperly maintained ;
alterations have been made t o the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE O F THE PRODUCT. THIS DISCLAIMER
APPLIES BOTH DURING AND AFTER THE TERM O F THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED
WARRANTIES O F “MERCHANTABILITY” AND “FITNESS FOR A SPECIFIC PURPOSE,
AFTER THE ONE-YEAR TERM O F THIS WARRANTY.
This Warranty gives you specific legal rights, and you may also have other rights which vary from
state t o state. Some states d o not allow the exclusion or limitation of incidental or consequential
dmagea, ao the above limitation or exclusion may not apply to you. Some states d o not allow
limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
J
Makita Corporation of America
2650 Buford Hwy., Buford, GA 30518
MCA‘ 3-97
.-
884101-062
PRINTED IN USA
1997-03-4