Bosch Fireray100RV Technical data

Installation Instructions
Linear Smoke Detector Fireray 50/100RV
Table of Contents
1.
Mounting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
1.1.
Connections and DIP switch settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
1.2.
Mounting the Fireray 50/100RV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
1.3.
Mounting the prism reflector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
1.4.
Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
2.
Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
2.1.
Setting up the detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
2.2.
Aligning the detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
2.3.
System test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
3.
Tips on Maintenance and Service . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
4.
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
5.
Additional Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
6.
Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
6.1.
Installation protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
6.2.
Fault diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
6.3.
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
Page 1 of 14
610-F.01U.002.706 / A2.en
ST/PMF/zab
Installation Instructions
Mounting Tips
Usually, the detector and the reflector are installed at the same height and oriented
towards each other. The relatively broad angle of the IR beam eases adjustment
and guarantees reliable long- term stability.
The mounting surface for the detector must be firm and vibration- free. Metal
supports that can be influenced by heat or cold are not suitable for installation.
The detector must be installed such that sunlight and artificial light do not beam
directly into the detector’s lenses. Normal environmental light conditions have no
effect on the IR beam and the evaluation.
Mount the reflector on a solid surface at the permissible distance. Ensure that the
light beam meets the reflector on the vertical.
The reflectors must not be mounted on reflective surfaces such as glass or plain
sheet surfaces. Additional reflections lead to malfunctions.
For protection against radio interference, use a shielded cable. When you are
installing the cable, possible sources of disturbance must be circumvented and the
cable must be protected against mechanical damage.
A 6 DA mini distributor (product ID 2.798.400.302) is required for wiring.
There must be a free visual line between the detector and
reflector. The IR light beam must not be blocked by moved
objects!
120 mm
Detector baseplate
Operating mode switch
Receiver window
Gimbal bearing
210 mm
1.
Linear Smoke Detector Fireray 50/100RV
Transmitter window
Knurled screw for
horizontal adjustment
(on right of detector)
Operating indicator
LEDs
Knurled screw for
vertical adjustment
Detector cover
Fig. 1.: Detector side view
Page 2 of 14
610-F.01U.002.706 / A2.en
ST/PMF/zab
Installation Instructions
Linear Smoke Detector Fireray 50/100RV
1.1. Connections and DIP switch settings
on
Mounting slots
off
DIP switch
Operating
mode switch
Plug connector
2-pin output for
key switch (optional)
Fig. 2.: Reverse side of detector with plug connector, operating mode switch and
DIP switch
DIP switch
The DIP switches can be accessed through the round recess in the detector base plate.
Table 1.: Functions of the DIP switch settings
*
X
X
Function
DIP switch settings
1
2
3
4
50% threshold
X
X
OFF
OFF
35% threshold
X
X
OFF
ON
25% threshold
X
X
ON
OFF
12% threshold
(extremely sensitive, only for special applications!)
X
X
ON
ON
Alarm relay saves the alarm
OFF
X
X
X
Automatic reset 5 s after the end of the alarm criterion
ON
X
X
X
Alarm relay after end of readjustment
X
OFF
X
X
Fault relay at end of readjustment, no alarm
X
ON
X
X
The factory presets are shaded in gray.
* The recommended settings for connection to a fire panel are marked with X.
Use DIP switches 3 and 4 to set the required alarm threshold. The factory setting
is moderate sensitivity (35%) for normal environmental conditions. Select a
threshold of 50% in very dirty environments.
Use DIP switch 1 to select the «Save alarm » or «Auto Reset» function
(recommended setting for connection to fire panel = «Save alarm »).
Page 3 of 14
610-F.01U.002.706 / A2.en
ST/PMF/zab
Installation Instructions
Linear Smoke Detector Fireray 50/100RV
Plug connector
The plug connector can be accessed through the oval recess on the detector base plate.
Table 2.: Pin assignment of the 8- pin connector (from left to right)
PIN number
Wire color
1
Function
Not assigned
2
blue
3
yellow
Alarm relay, work contact (NO)
4
red
Power supply +10 to +30 V DC
5
black
Power supply -
6
green
Fault relay, normally closed contact (NC)
7
white
Fault relay, center contact (COM)
8
Alarm relay, center contact (COM)
Not assigned
1.2. Mounting the Fireray 50/100RV
To make mounting easier, you can remove the detector cover by gently raising the
upper and lower edges.
The mounting slots (see Fig. 2.), which are positioned at a 90angle, enable vertical
or horizontal mounting of the detector.
Locate the four bore holes at the mounting location using the detector base plate.
Observe the planning notes and mounting tips!
Check the plug connector and the DIP switch settings (see Section 1.1.).
Secure the detector using four screws.
Refit the detector cover.
If a key switch is required, a two- wire cable should be routed from the detector to
the desired location during installation.
1.3. Mounting the prism reflector
Select the mounting location in line with the mounting tips (Section 1.).
A prism reflector must be used for the Fireray 50RV, and four prism reflectors
arranged in a square for the Fireray 100RV.
ÌÌÌ
ÌÌÌ
ÌÌÌ
ÌÌÌ
Fireray 50RV
Fig. 3.: Prism reflectors
ÌÌÌÌ
ÌÌÌÌ
ÌÌÌÌ
ÌÌÌÌ
ÌÌÌÌ
ÌÌÌÌ
ÌÌÌÌ
ÌÌÌÌ
ÌÌÌÌ
ÌÌÌÌ
ÌÌÌÌ
ÌÌÌÌÌÌÌÌ
ÌÌÌÌ
Fireray 100RV
Each reflector is secured using two mounting bores (Ğ 3 mm). Arrange the four
reflectors for the Fireray 100RV such that there are no mounting holes in the center
(see Fig. 3.).
Page 4 of 14
610-F.01U.002.706 / A2.en
ST/PMF/zab
Installation Instructions
Linear Smoke Detector Fireray 50/100RV
1.4. Connection
Connection of a Fireray 50/100RV using a NSB100 LSN at the fire panel
1
Bridges Br1, Br2 in position 2-3
2
Contacts in open position
NSB 100 LSN
I1 NLT1
Configuration for LSN:
Parameterize the NSB in the control
panel to control output
KA1-KA2/KR-R-RR and “Control with
Fireray”.
VII2
I4 +U
LSN
II1 NLT2
Br 1
II2 ⊥
on
1
2
3
1
II3 -U
DIP switch
(recommended setoff
Operating mode tings)
switch
Br 2
II4 +U
1
2
3
III1
III2
FAULT
Power supply 10 - 30
V
ALARM
IV1 RR
IV2 R
2
V1 KR
COM
NC
NO
COM
+ -
VII1
I3 -U
Fireray 50/100 RV
Output
for key switch
(optional)
SA
SB
I2 ⊥
V2 KA1
V3 KA2
RE
3K3
680 Ω
VI1
VI2
UEB
gn
rd
bl
UEA
wh
blk
ye
Operating mode switches:
Prism Targeting
Alignment Mode
Operating Mode
6 DA mini
distributor
-U
+U
-U
DIP switch:
Functions, see table 1. (page 3)
I3
+U
I4
NSB 100
(if voltage drop < 6 V)
EV 24 V - 24 V
(if voltage drop > 6 V)
Select the following DIP switch settings for connection to a fire panel (see table
1. on page 3):
- «Alarm relay saves the alarm»
- «Fault relay at end of readjustment, no alarm».
Page 5 of 14
610-F.01U.002.706 / A2.en
ST/PMF/zab
Installation Instructions
Linear Smoke Detector Fireray 50/100RV
Connection of two Fireray 50/100RV to fire panel with cross zoning via an NBK
100 LSN and two NSB100 LSNs
1
Bridges Br1, Br2 on the NSB 100 in position 2-3 (see connection of one Fireray 50/100RV)
2
Contacts in open position
Configuration for LSN:
Parameterize the NSB in the control panel to control output
KA1-KA2/KR-R-RR and “Control with Fireray”.
Observe assignment to detector groups/detectors (see example).
NBK 100 LSN
Fireray 50/100 RV
Parameterize, e.g. to 127/1
VI1
DIP switch
(recommended
Operating mode settings)
switch
VI2
V1
V2
500/1 cross zoning with 150,
Line 2 current trigger criterion
2
COM
NC
-
+
NO
COM
3k92
820
bl
FAULT
Power supply 10 - 30
V
ALARM
Output
for key switch
(optional)
150/1 cross zoning with 500,
Line 1 current trigger criterion
ye
rd
blk
gn
NSB 100 LSN
wh
Parameterize, e.g. to 127/2
V1 KR
V2 KA1
Parameterize, e.g. to
V3 KA2
KA1-KA2-KR-150/2
6 DA mini
distributor
1
Fireray 50/100 RV
DIP switch
(recommended
Operating mode settings)
switch
NSB 100 LSN
Parameterize, e.g. to 127/3
2
V2 KA1
Parameterize, e.g. to
V3 KA2
KA1-KA2-KR-500/2
COM
NC
1
3k92
820
rd
ye
-
+
NO
COM
bl
FAULT
Power supply 10 - 30
V
ALARM
Output
for key switch
(optional)
V1 KR
blk
gn
wh
6 DA mini
distributor
-U
+U
-U
I3
+U
I4
NSB 100
(if voltage drop < 6 V)
Page 6 of 14
EV 24 V - 24 V
610-F.01U.002.706 / A2.en
ST/PMF/zab
Installation Instructions
2.
Linear Smoke Detector Fireray 50/100RV
Start- Up
2.1. Setting up the detector
Start the «Prism Targeting»mode by moving the operating mode switch (see Fig.
2.) up (if the detector is mounted vertically) or to the right (if the detector is mounted
horizontally).
Connect the power supply.
The detector runs in initialization mode for approx. 5 s. The red LED flashes if the
detector is operational: 1 x for Fireray 50RV, 2 x for Fireray 100RV.
Now direct the detector at the prism, using the two knurled screws, until optimum
adjustment is confirmed by a steady yellow LED light. The following LED displays
support detector set- up:
Yellow LED display
Detector status in «Prism Targeting» operating mode
off
No signal at receiver
Flashes
-> Flashing frequency increasing
Signal is received
-> The faster the flashing, the stronger the signal!
Steady light
Optimum alignment achieved
The signal must only move from the reflector to the receiver,
under no circumstances must it move to other light sources or
reflective surfaces!
Cover the prism reflector with a non-reflective material to check. The LED must not be
lit. If the yellow LED does not go out, this indicates that a reflector is incorrectly aligned.
2.2. Calibrating the detector
Once the optimum detector set- up has been achieved, set the operating mode
switch to the center position without displacing the detector. The detector is now in
(«Alignment Mode»).
The detector runs through an automatic configuration procedure to optimize the
transmission power and the receiver sensitivity. The following detector statuses
may be displayed by the LEDs during this procedure:
LED displays
Detector statuses in «Alignment Mode»
Flashing red
Receiver input signal too strong, the transmission power will be
reduced. Wait until the LED goes out (max. 20 s).
Steady yellow light
No signal is being received. Switch back to «Prism Targeting» mode
and repeat the detector set-up.
Flashing yellow
The receiver is receiving a weak signal, the transmission power will
automatically be increased.
off
Transmission power and receiver gain are optimum.
Flashing red and
yellow
Automatic calibration in progress.
Page 7 of 14
610-F.01U.002.706 / A2.en
ST/PMF/zab
Installation Instructions
Linear Smoke Detector Fireray 50/100RV
Follow the flow chart to perform the calibration process:
Switch center Alignment
Mode Yellow LED lights up
for approx. 5 s
No signal: back to
detector
set -up (Section 2.1.)
Steady
Wait until both LEDs have
stopped flashing
yellow LED
Turn the knurled screws in
one direction and monitor
the LED status
yellow
LED
Which LED
lights up?
red
LED
Stop turning the knurled
screw and wait until the red
LED stops flashing
Turn the knurled screw
slowly in the same direction
Turn the knurled screw in
the other direction
yellow
LED
Which LED
lights up?
red
LED
No LED
Repeat the
procedure for the other
detector axis with the
second knurled screw
no
Both axes adjusted?
Do not turn the knurled
screw any further
y
e
Check optimum setting:
s
Yellow LED lights up:
1. With gentle pressure from top/bottom/left/right
on the detector housing.
2. Each time the knurled screws are moved.
Exit the
Alignment Mode
Switch at bottom:
Operating Mode
Page 8 of 14
610-F.01U.002.706 / A2.en
ST/PMF/zab
Installation Instructions
Linear Smoke Detector Fireray 50/100RV
When the calibration procedure is complete, move the operating mode switch to the
bottom (if the detector is mounted vertically) or to the left (if the detector is mounted
horizontally). The detector is now in «Operating Mode».
The detector runs a calibration test for approx. 60 s. If the yellow LED lights up as
a steady light after the test, you must repeat the detector alignment and calibration
procedures (see Sections 2.1. and 2.2.).
If a detector alarm is reset in normal mode by a disruption of the power
supply, the detector automatically runs a calibration test. If the test is
failed, the detector remains in the alarm position. If the test is positive,
the yellow LED goes out, the fault relay is reset and the detector is
returned to normal mode.
In normal mode, the yellow LED flashes every 10 s.
2.3. System test
The «Alarm» and «Malfunction» functions must be checked before final start - up.
Alarm test
Hold the test filter in front of the receiver lens (upper or right- hand part of detector).
Select a volume of smoke slightly greater than the threshold set for the detector (see
Section 1.1.). Make sure that you do not also cover the transmitter -lens.
After approx.10 s, the red LED must light up and the alarm relay must close.
With the «Save alarm » detector setting (DIP switch 1 «off»), there must be a reset
at the control panel or the power supply must be disrupted for at least 5 s.
With the setting «Auto Reset» setting (DIP switch 1 «on»), the alarm is reset
automatically if the volume of smoke falls below the selected alarm threshold for at
least 5 s.
Fault test
Cover the reflector with a non- reflective material.
After approx. 10 s, the yellow LED must light up and the fault relay must open. As
soon as the obstruction is removed, the detector returns to normal mode
automatically after approx. 2 s.
3.
Tips on Maintenance and Service
For maintenance and inspection work on danger detector systems, in Germany
the regulations of DIN VDE 0833 apply, which refer to the maintenance interval
according to the manufacturer’s instructions.
Bosch ST recommends a functional and visual inspection at least once a year.
Maintenance and inspection work should be carried out regularly and by trained
personnel.
Page 9 of 14
610-F.01U.002.706 / A2.en
ST/PMF/zab
Installation Instructions
4.
Linear Smoke Detector Fireray 50/100RV
Technical Data
Operating voltage
10 V DC . . . 30 V DC
Current consumption:
- in standby mode
- in alarm/malfunction
< 4 mA @ 24 V
< 15 mA
Reset control by power disruption
Alarm relay
Fault relay
Permissible distance between Fireray and the
reflector:
- Fireray 50RV
- Fireray 100RV
Optical wavelength
5 m to 50 m
50 m to 100m
880 nm
Adjustable alarm threshold values
2.50 dB (25%)
3.74 dB (35%)
6.02 dB (55%)
Detector $0.8
Prism reflector $5.0
Axial deviation tolerance
(at 35% sensitivity)
Operating temperature
- 30C . . . +55C
Protection type
IP 50
Dimensions (W x H x D)
126 x 210 x 120 mm
Weight
670 g
Housing:
- Color
- Material
light gray/black
ABS, non- flammable
VdS ID number
5.
>5s
Normally open; dry
contact
(2 A @ 30 V DC)
Normally close; dry
contact
(2 A @ 30 V DC)
G 203070
Additional Documentation
For those with access authorization, on the Bosch ST ExtraNet at
www.boschbest.de
the current information for each product, as well as the installation instructions
supplied with the device, are available for download as a PDF file.
Page 10 of 14
610-F.01U.002.706 / A2.en
ST/PMF/zab
Installation Instructions
6.
Linear Smoke Detector Fireray 50/100RV
Appendices
6.1. Installation protocol
Installation company:
Type of object:
Installation location:
Installation date:
Total number of all linear detectors:
Detector version:
Detector – reflector distance:
_________ m
Distance of the detector axes to one
another
_________ m
Mounting height
_________ m
Fireray 50RV
Fireray 100RV
Mounting surface (e.g. masonry/reinforced concrete/steel beams/wood/etc.)
Serial number(s)
Reflector size:
Supply voltage:
_________ V
Correct mechanical adjustment
of transmitter
(when gentle pressure is applied to the
detector housing from the left/right/top/
bottom, the yellow LED lights up initially):
yes
no
Alarm triggered with absorption film
35% - 50% tested:
yes
no
Fault triggered by disruption of IR
beam tested:
yes
no
1 x (10 x 10 cm)
4 x (20 x 20 cm)
DIP switch settings:
1
2
3
4
on
off
Comments (environmental conditions, e.g. dust, humidity, temperature etc.)
Installation tested on: ____________
by: __________________________
Page 11 of 14
610-F.01U.002.706 / A2.en
ST/PMF/zab
Installation Instructions
Linear Smoke Detector Fireray 50/100RV
6.2. Fault diagnosis
Fault indicator
Fault LED illuminated permanently
Possible cause
Action
Beam path blocked by an obstacle
Check and/or ensure free visual line
in the area between the detector and
the reflector.
Reflector is contaminated/covered/
has fallen down.
Check the status of the reflector and
clean it if necessary.
Supply voltage too low.
Measure supply voltage directly at
detector.
Mode sliding switch in upper position
(«Direct»)
Set the switch to «Operation» and
wait until the 60 s activation routine is
complete.
Detector set-up changed on switching to «Operation».
When operating the sliding switch following the correct adjustment, make
sure that the setting is not changed.
The limit of automatic gain control has Clean detector lens and reflector and
been reached
correct mechanical adjustment!
Fault LED flashes
Alarm LED
illuminated
permanently
No fault message
when IR beam is
disrupted
Alarm triggered
when IR beam is
disrupted
Triggering of false
alarms
«MODE Switch» sliding switch in up- Align detector vertically and horizontally until the fault LED is permanently
per position («Direct») and incomplete detector set-up
illuminated. Then continue using fine
adjustment (switch in center position)!
DIP switch 1 at OFF
(«Save alarm »),
the alarm display remains saved
Reset the detector by disrupting the
supply voltage for at least 5 s or
select «Reset» on the fire panel
Beam path (partially) blocked by an
obstacle
Ensure a free visual line in the area
between the detector and the
reflector!
Detector receives partial IR signal,
e.g. via reflective surfaces near the
beam axis.
Cover reflector with a dark material to
test!
Check detector’s range of vision for
reflective objects!
An object placed in the beam path for
testing has acted as the reflector.
For testing, use a non-reflective
material, maintain a greater distance
to the detector, cover the reflector as
directly as possible.
Sensitivity to existing environmental
conditions set too high
Select a less sensitive alarm threshold (DIP switches 3 and 4):
normal= 35%, less sensitive= 50%
Page 12 of 14
610-F.01U.002.706 / A2.en
ST/PMF/zab
Installation Instructions
Linear Smoke Detector Fireray 50/100RV
6.3. Notes
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
Page 13 of 14
610-F.01U.002.706 / A2.en
ST/PMF/zab
Bosch Security Systems
Robert -Koch -Str. 100
D-85521 Ottobrunn
Info -Service
Telephone: +49 89 6290 - 1039
Fax:
+49 89 6290 - 1039
www.bosch -sicherheitssysteme.de
info.service@de.bosch.com