Epson EMP-83H User`s guide

Add to my manuals
78 Pages

advertisement

Epson EMP-83H User`s guide | Manualzz
1
User's Guide
Notations Used in This Guide
f Safety Indications
So that you can use the projector safely and correctly, symbols are applied in the documentation and on the projector to indicate possible harm to the user or
to others and the risk of damage to property.
The indications and their meaning are as follows. Make sure you understand them properly before reading the guide.
Warning
Indicates the possibility of death or serious injury if this symbol is ignored or if sufficient care is not taken.
Caution
Indicates the possibility of injury or damage to property if this symbol is ignored or if sufficient care is not taken.
f General Information Indications
Attention
q
s
g
Procedure
[ (Name) ]
"(Menu Name)"
Indicates procedures which may result in damage or injury if sufficient care is not taken.
Indicates additional information and points which may be useful to know regarding a topic.
Indicates a page where detailed information regarding a topic can be found.
Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See
the "Glossary" section of the "Appendices". s p.65
Indicates operating methods and the order of operations.
The procedure indicated should be carried out in the order of the numbered steps.
Indicates the name of the buttons on the remote control or the control panel.
Example: [Esc] button
Indicates configuration menu items.
Example: "Image" - "Brightness"
Indicates that the explanation continues on the following page. Clicking this symbol will display the following page.
Indicates that the explanation is continued from the previous page. Clicking this symbol will display the previous page.
2
Contents
Projector Features......................................................................................4
Part Names and Functions ........................................................................5
Front/Top.............................................................................................................. 5
Rear (EMP-83H/822H Only) ................................................................................ 6
Rear (EMP-X5/S5 Only)....................................................................................... 7
Control Panel ....................................................................................................... 8
Remote Control .................................................................................................. 10
Base ................................................................................................................... 11
Useful Functions
Changing the Projected Image (Source Search) ...................................13
Functions for Enhancing Projection.......................................................14
Selecting the Projection Quality (Selecting Color Mode) ................................... 14
Hiding the Image and Sound Temporarily (A/V Mute) ....................................... 15
Freezing the Image (Freeze).............................................................................. 16
Changing the Aspect Ratio (Aspect) .................................................................. 16
Enlarging Part of the Image (E-Zoom) ............................................................... 17
Security Functions ...................................................................................18
Managing Users (Password Protect) ................................................................. 18
Restricting Operation (Operation Lock).............................................................. 20
Anti-Theft Lock ................................................................................................... 21
Configuration Menu
Using the Configuration Menu ................................................................23
List of Functions.......................................................................................24
Image Menu (EMP-83H/822H Only) .................................................................. 24
Image Menu (EMP-X5/S5 Only)......................................................................... 25
Signal Menu (EMP-83H/822H Only) .................................................................. 26
Signal Menu (EMP-X5/S5 Only)......................................................................... 27
Settings Menu .................................................................................................... 28
Extended Menu .................................................................................................. 29
Network Menu (EMP-83H/822H Only) ............................................................... 31
Info Menu (Display Only).................................................................................... 34
Reset Menu........................................................................................................ 35
Troubleshooting
Using the Help ..........................................................................................37
Problem Solving .......................................................................................38
Reading the Indicators ....................................................................................... 38
When the Indicators Provide No Help ................................................................ 41
3
Appendices
Installation Methods ................................................................................ 49
Cleaning .................................................................................................... 50
Cleaning the Projector's Surface ....................................................................... 50
Cleaning the Lens.............................................................................................. 50
Cleaning the Air Filter and Air Intake Vent......................................................... 50
Replacing Consumables ......................................................................... 51
Replacing the Remote Control Batteries ........................................................... 51
Replacing the Lamp........................................................................................... 52
Replacing the Air Filter ...................................................................................... 56
Saving a User's Logo............................................................................... 57
Screen Size and Distance........................................................................ 59
EMP-83H/822H/X5 ............................................................................................ 59
EMP-S5 ............................................................................................................. 60
Connecting to External Equipment ........................................................ 61
Connecting to an External Monitor .................................................................... 61
Connecting to External Speakers (EMP-83H/822H Only) ................................. 61
Connecting a LAN Cable (EMP-83H/822H Only).................................... 62
Connecting a USB Cable (EMP-X5/S5 Only).......................................... 63
Optional Accessories and Consumables .............................................. 64
Glossary.................................................................................................... 65
ESC/VP21 Commands ............................................................................. 67
Command List.................................................................................................... 67
Cable Layouts.................................................................................................... 67
Connecting a USB (EMP-X5/S5 Only)............................................................... 68
USB Connection Setup...................................................................................... 68
PJLink (EMP-83H/822H Only).................................................................. 69
List of Supported Monitor Displays ....................................................... 70
Specifications........................................................................................... 71
Appearance............................................................................................... 75
Index.......................................................................................................... 76
Projector Features
Ease of use
f The A/V mute slide makes it easy to project and store
You can stop and resume projection
easily by opening and closing the A/V
mute slide which makes giving clear
presentations easier.
4
Enhanced security functions
f Password Protect to restrict and manage users
By setting a password you can restrict who can use the projector. s p.18
f Operation Lock restricts button operation on the control panel
You can use this to prevent people from changing projector settings
without permission at events, in schools, and so on. s p.20
f A single foot design means you do not have to make any difficult
levelling adjustments
You can easily make height
adjustments with one hand.
sQuick Start Guide
f Equipped with various anti-theft devices
The projector is equipped with the following security devices. s p.21
• Security slot
• Security cable installation point
Easy to handle
f Direct power On/Off (EMP-83H/822H only)
In places where power is managed centrally, such as in a conference
room, the projector can be set to power on and off automatically when the
power source to which the projector is connected is switched on or off.
f No cool down delay
After turning the projector's power off, you can disconnect the projector's
power cable without having to wait for the projector to cool down first.
Part Names and Functions
5
Front/Top
Name
K
A
J
I
H
B
C
G
F
E
D
Name
Function
A
Control panel
s p.8
B
Lamp cover
Open this cover when replacing the projector's
lamp. s p.53
C
Air exhaust vent
Caution
Do not place objects that may become warped
or otherwise affected by heat near the air
exhaust vent and do not put your face or
hands near the air exhaust vent while
projection is in progress.
Function
D
Front adjustable
feet
Extend and adjust the position of the projected
image when the projector is placed on a
surface such as a desk. s Quick Start Guide
E
Foot adjust lever
Pull out the foot lever to extend and retract the
front foot. s Quick Start Guide
F
A/V mute slide
Slide shut when not using the projector to
protect the lens. By closing during projection
you can hide the image and the sound (A/V
Mute). s Quick Start Guide, p.15
G
Remote receiver
Receives signals from the remote control.
s Quick Start Guide
H
Focus ring
Adjusts the image focus. s Quick Start Guide
I
Zoom ring
(EMP-83H/822H/
X5 only)
Adjusts the image size. s Quick Start Guide
J
A/V mute slide
knob
Slide the knob to open and close the A/V mute
slide.
K
Security slot (j)
The security slot is compatible with the
Microsaver Security System manufactured by
Kensington. s p.21
6
Part Names and Functions
Rear (EMP-83H/822H Only)
A
H
G
F
Name
Function
E
RS-232C port
When controlling the projector from a
computer, connect it to the computer with an
RS-232C cable. This port is for control use and
should not normally be used. s p.67
F
Computer1 input
port
For video signals from a computer and
component videog signals from other video
sources.
Audio1 input port Connect to the audio out port of the computer
connected to the Computer1 input port.
Computer2 input
port
B
C
Name
A
Remote receiver
B
Speaker
C
Monitor Out port
D
D E
Audio2 input port Connect to the audio out port of the computer
connected to the Computer2 input port.
s Quick Start Guide
Function
Receives signals from the remote control.
s Quick Start Guide
Outputs the image signal from the computer
connected to the Computer1 input port to an
external monitor. This is not available for
component videog signals or other signals
being input to any port other than the
Computer1 input port.s p.61
Audio Out port
Outputs the sound of the image currently being
projected to external speakers. s p.61
Power inlet
Connects to the power cable.
s Quick Start Guide
For video signals from a computer and
component videog signals from other video
sources.
G
H
S-Video input
port
For S-videog signals from video sources.
Video input port
For composite videog signals from video
sources.
Audio-L/R input
port
Connects to the audio out port of the
equipment connected to the S-Video port or
Video input port. s Quick Start Guide
LAN port
When a LAN cable is connected, you can
monitor and control the projector over a LAN.
s p.62
7
Part Names and Functions
Rear (EMP-X5/S5 Only)
A I HG
B
Name
A
Remote receiver
B
Speaker
C
Power inlet
D
Monitor Out port
F
Name
E
D
C
Function
Receives signals from the remote control.
s Quick Start Guide
Connects to the power cable.
s Quick Start Guide
Outputs the image signal from the computer
connected to the Computer input port to an
external monitor. This is not available for
component videog signals or other signals
being input to any port other than the
Computer input port.s p.61
Function
E
Computer input
port
For video signals from a computer and
component videog signals from other video
sources.
F
Audio-L/R input
port
Connects to the audio output port for the
equipment you want to project from and inputs
the audio. s Quick Start Guide
G
Video input port
For composite videog signals from video
sources.
H
S-Video input
port
For S-videog signals from video sources.
I
USB port (Type B) When showing a slide show in PowerPoint,
you can use the projector's remote control to
move to the next slide/previous slide if it is
connected to a computer by a USB cable.*
Also, you can use it as a control port when the
projector is controlled by a computer.
Even if the projector is connected to a
computer by a USB cable, you cannot project
the image on the computer. s p.63
* Limited to computers with the following operating systems installed.
Windows 98/98SE/2000/Me/XP Home Edition/XP Professional
Macintosh: OS 8.6 to 9.2/10.1 to 10.3
8
Part Names and Functions
Control Panel
Name
f EMP-83H/822H/X5
A
B
I
C
H
D
G
E
F
A
[Power] button
Turns the projector power on or off.
s Quick Start Guide
B
Status indicators
The color of the indicators and whether they
are flashing or lit indicates the status of the
projector. s p.38
C
[Source Search]
button
Changes to the next input source that is
connected to the projector and is sending an
image.s p.13
D
[Enter] button
If pressed during projection of computer signal
images, it automatically adjusts the tracking,
synchronization, and position to project the
optimum image.
When a configuration menu or a help screen is
displayed, it accepts and enters the current
selection and moves to the next level.s p.23
E
[v] [w] buttons
Corrects keystone distortion.
If pressed when a configuration menu or a help
screen is displayed, these buttons select menu
items and setting values.
s Quick Start Guide, p.23
F
[Help] button
Displays and closes the help screen which
shows you how to deal with problems if they
occur.s p.37
G
[Esc] button
Stops the current function.
If pressed when a configuration menu is
displayed, it moves to the previous menu
level.s p.23
H
[a] [b] buttons
(EMP-83H/822H/
X5 only)
Press to adjust the volume.
If pressed when a configuration menu or a help
screen is displayed, these buttons select menu
items and setting values.
s Quick Start Guide, p.23
f EMP-S5
Buttons without numbers operate in the same way as in the figure above.
See the numbers in the table for the figure above.
J
Function
9
Part Names and Functions
Name
Function
I
[Menu] button
Displays and closes the configuration
menu.s p.23
J
[Wide] [Tele]
buttons
(EMP-S5 only)
Adjusts the image size.
If pressed when a configuration menu or a help
screen is displayed, these buttons select menu
items and setting values.
s Quick Start Guide, p.23
10
Part Names and Functions
Remote Control
Name
P
A
B
C
D
E
F
G
O
N
M
L
K
J
I
Name
C
[Menu] button
Displays and closes the configuration menu.
s p.23
D
[Enter/Auto]
button
If pressed during projection of computer signal
images, it automatically adjusts the tracking,
synchronization, and position to project the
optimum image. s p.26
When a configuration menu or a help screen is
displayed, it accepts and enters the current
selection and moves to the next level.s p.23
E
[Color Mode]
button
Each time the button is pressed, the color
mode changes.s p.14
F
[Page] button
(Down) (Up)
(EMP-X5/S5 only)
When showing a slide show in PowerPoint,
you can use the projector's remote control to
move to the next slide/previous slide if it is
connected to a computer by a USB cable.*
s p.63
G
[E-Zoom] button
(+) (-)
(+) Enlarges the image without changing the
projection size.
(-) Reduces parts of the image that have been
enlarged using the [+] button.s p.17
H
[A/V Mute] button Turns the video and audio on or off. s p.15
I
[Freeze] button
Images are paused or unpaused.s p.16
J
[Aspect] button
The aspect ratiog changes each time the
button is pressed.s p.16
K
Numeric buttons
Use these buttons when entering a password.
s p.19
H
Illustrations show EMP-X5/S5.
Function
A
[Power] button
Turns the projector power on or off.
s Quick Start Guide
B
[Source Search]
button
Changes to the next input source that is
connected to the projector and is sending an
image.s p.13
Function
* Limited to computers with the following operating systems installed.
Windows 98/98SE/2000/Me/XP Home Edition/XP Professional
Macintosh: OS 8.6 to 9.2/10.1 to 10.3
11
Part Names and Functions
Name
Function
Base
L
[Volume -] button Press [Volume -] to lower the volume and
[Volume +] button press [Volume +] to raise the volume.
If pressed when a configuration menu or a help
screen is displayed, these buttons select menu
items and setting values.
s Quick Start Guide , p.23
M
[Esc] button
Stops the current function. If pressed when a
configuration menu is displayed, it moves to
the previous level. s p.23
N
[Help] button
Displays and closes the help screen which
shows you how to deal with problems if they
occur.s p.37
O
[u] [d] buttons
If pressed when a configuration menu or a help
screen is displayed, these buttons select menu
items and setting values. s p.23
B
P
Remote control
light-emitting
area
Outputs remote control signals.
s Quick Start Guide
C
D
A
B
Name
Function
A
Suspension
bracket fixing
points (3 points)
Attach the optional ceiling mount here when
suspending the projector from a ceiling.
s p.49, 64
B
Rear foot
(2 points)
Turn to extend and retract to adjust the
horizontal tilt. s Quick Start Guide
C
Security cable
installation point
Pass a commercially available anti-theft wire
lock through here when you want to secure the
projector to a fixed object. s p.21
D
Air filter (Air
intake vent)
This prevents dust and other foreign particles
from getting inside the projector when air is
drawn in. The projector displays a warning
message when it is time to clean or replace the
air filter.s p.50, 56
Useful Functions
This chapter explains useful functions for giving presentations and so on, and the security functions.
Changing the Projected Image
(Source Search) .................................................. 13
Security Functions..............................................18
Functions for Enhancing Projection ................. 14
Type of Password Protect .............................................................. 18
Setting Password Protect................................................................ 19
Entering the Password.................................................................... 20
• Selecting the Projection Quality
(Selecting Color Mode) .....................................................14
• Hiding the Image and Sound Temporarily
(A/V Mute) .........................................................................15
• Freezing the Image (Freeze).............................................16
• Changing the Aspect Ratio (Aspect)................................16
• Enlarging Part of the Image (E-Zoom) ...........................17
• Managing Users (Password Protect)............................... 18
• Restricting Operation (Operation Lock)........................ 20
• Anti-Theft Lock ................................................................ 21
Installing the wire lock................................................................... 21
Changing the Projected Image (Source Search)
The projector automatically detects signals being input from connected
equipment, and the image being input from the equipment is projected.
You can project the target image quickly because it skips input ports
where no image is being input.
Computer1
Computer2*
S-Video
Video
q
13
The following screen showing the status of image signals is
displayed when only the image that the projector is
currently displaying is available, or when no image signal
can be found. You can select the input port where the
connected equipment you want to use is projecting. If no
operation is performed after about 10 seconds, the screen
closes.
For EMP-83H/822H
The input port where no image
signal is being input is skipped.
* EMP-83H/822H only
Procedure
When your video equipment is connected, start playback before beginning
this operation.
Using the remote control
Using the control panel
When two or more pieces of equipment are connected, press the
[Source Search] button until the target image is projected.
Functions for Enhancing Projection
Selecting the Projection Quality (Selecting Color
Mode)
14
Procedure
Remote control
You can easily obtain the optimum image quality simply by selecting the
setting that best corresponds to your surroundings when projecting. The
brightness of the image varies depending on the mode selected.
Mode
Game
Presentation
Text
Theatre
Photo
Sports
sRGBg
Blackboard
Application
Ideal for use in a bright room. This is the brightest
mode and reproduces shadow tones well.
Ideal for making presentations using color materials
in a bright room.
Ideal for making presentations using black-andwhite materials in a bright room.
Ideal for watching films in a dark room. This gives
images a natural tone.
(When computer images are input)
Ideal for projecting still pictures, such as photos, in a
bright room. This makes images vivid and brings
them into contrast.
(When component video, S-video, or composite
video images are input)
Ideal for watching TV programmes in a bright room.
This makes images vivid and brings them to life.
Ideal for images that conform to the sRGB color
standard.
Even if you are projecting onto a blackboard
(greenboard), this setting gives your images a natural
tint, just like when projecting onto a screen.
Each time you press the button, the color mode name is displayed on the
screen and the color mode changes.
If you press the button while the color mode name is displayed on the
screen, it changes to the next color mode.
q
The color mode can also be set using "Color Mode" from
the "Image" menu in the configuration menu. s p.24, 25
15
Functions for Enhancing Projection
Hiding the Image and Sound Temporarily (A/V Mute)
You can use this when you want to focus the audience's attention on what
you are saying, or if you do not want to show details such as when you are
changing between files during presentations from a computer.
q
• If you use this function when projecting moving images,
the images and sound continue to be played back by the
source, and you cannot return to the point where A/V
Mute was activated.
• From the remote control you can choose to display black,
blue, or logo* as the A/V mute display using the
"Extended" - "Display" - "A/V Mute" setting in the
configuration menu. s p.29
• When the A/V mute slide is closed and A/V Mute begins,
the power supply can be set to automatically turn off after
about 30 minutes by setting "Extended" - "Operation" "Lens Cover Timer" in the configuration menu. s p.30
Procedure
Remote control
Projector
Each time you press the button, or the A/V mute slide is opened or closed,
A/V Mute turns on or off.
* Depending on the area of purchase, the User's Logo function may not be
available for EMP-X5/S5.
16
Functions for Enhancing Projection
Freezing the Image (Freeze)
When the moving image on the screen is frozen, the image continues to
project, so you can project a moving image one frame at a time like a still
photo. Also, you can perform operations such as changing between files
during presentations from a computer without projecting any images if the
Freeze function is activated beforehand.
Changing the Aspect Ratio (Aspect)
When video equipment is connected, images that have been recorded in
digital video or onto DVDs can be viewed in 16:9 wide-screen format.
You can change the aspect ratiog for images in squeeze modeg as
follows.
4:3
16:9
16:9 (Up)
16:9 (Down)
Procedure
Remote control
Procedure
Remote control
Each time you press the button, Freeze turns on or off.
q
• Audio does not stop.
• The image source continues to play back the moving
images even while the screen is frozen, so it is not possible
to resume projection from the point where it was paused.
• If the [Freeze] button is pressed while the configuration
menu or a help screen is displayed, the menu or help
screen being displayed is cleared.
• Freeze still works while E-Zoom is being used.
Each time you press the button, the aspect name is displayed on the screen
and the aspect changes.
17
Functions for Enhancing Projection
If you press the button while the aspect name is displayed on the screen, it
changes to the next aspect mode.
the cross to the area of the image that you
B Move
want to enlarge.
Remote control
q
This can also be set using "Aspect" from the "Signal"
menu in the configuration menu. s p.26
Enlarging Part of the Image (E-Zoom)
This is useful when you want to expand images such as graphs and tables
to see them in greater detail.
Cross
C Enlarge.
Remote control
Procedure
A Start E-Zoom.
Each time the button is pressed, the area is expanded. You can
expand quickly by holding the button down.
You can reduce the enlarged image by pressing the [-] button.
Press the [Esc] button to cancel.
Remote control
q
• The enlargement ratio appears on the screen. The
selected area can be enlarged to between 1 to 4 times in 25
incremental steps.
• You can scroll the image by pressing [u], [d], [l], or [r].
Security Functions
The projector has the following enhanced security functions.
• Password Protect
You can limit who can use the projector.
• Operation Lock
You can prevent people from changing the settings on the projector
without permission.
• Anti-Theft Lock
The projector is equipped with various types of anti-theft security
devices.
Managing Users (Password Protect)
When the Password Protect function is activated, people who do not know
the password cannot use the projector to project images even if the
projector power is on. Furthermore, the user's logo that is displayed when
you turn on the projector cannot be changed. This acts as an anti-theft
device as the projector cannot be used even if it is stolen. At the time of
purchase the Password Protect function is not activated.
f Type of Password Protect
The following three kinds of password protect settings can be made
according to how the projector is being used.
1. "Power On Protect"
When "Power On Protect" is "On", the password must be entered
whenever the projector is turned on after it has been disconnected from
the power supply to which it was connected the last time the password
was entered. If the correct password is not entered, projection does not
start.
2 "User's Logo Protect"*
When "User's Logo Protect" is set to "On" the following setting
changes are prohibited.
• Capturing a user's logo
18
• Settings for "Display Background", "Startup Screen", and "A/V
Mute" are changed from "Display" in the configuration menu.
3 "Network Protect" (EMP-83H/822H only)
When "Network Protect" is set to "On" setting changes for "Network"
in the configuration menu are prohibited.
* Depending on the area of purchase, the User's Logo function may not be
available for EMP-X5/S5. In that case, "User's Logo Protect" is not
displayed.
19
Security Functions
f Setting Password Protect
Use the following procedure to set Password Protect.
Procedure
down the [Freeze] button for about five
A Hold
seconds.
The password protect setting menu is displayed.
Remote control
q
• If Password Protect is already activated, you must enter
the password.
If the password is entered correctly, the password protect
setting menu is displayed.
s "Entering the Password" p.20
• When the password is set, stick the password protect
sticker in a visible position on the projector as a further
theft deterrent.
B Turn on "Power On Protect".
(1) Select "Power On Protect", and then press the [Enter] button.
(2) Select "On", and then press the [Enter] button.
(3) Press the [Esc] button.
C Turn on "User's Logo Protect" .
*
(1) Select "User's Logo Protect", and then press the [Enter] button.
(2) Select "On", and then press the [Enter] button.
(3) Press the [Esc] button.
D Turn on "Network Protect".
(1) Select "Network Protect", and then press the [Enter] button.
(2) Select "On", and then press the [Enter] button.
(3) Press the [Esc] button.
E Set the password.
(1) Select "Password", and then press the [Enter] button.
(2) When the message "Change the password?" is displayed, select
"Yes" and then press the [Enter] button. The default setting for
the password is "0000". Change this to your own desired
password. If you select "No", the screen shown in step 1 is
displayed again.
(3) Enter a four digit number using the numeric buttons. The
number entered is displayed as "* * * *". When you enter the
fourth digit, the confirmation screen is displayed.
Remote control
Numeric buttons
(4) Re-enter the password.
The message "Password accepted." is displayed.
If you enter the password incorrectly, a message is displayed
prompting you to re-enter the password.
20
Security Functions
* Depending on the area of purchase, the User's Logo function may not be
available for EMP-X5/S5. In that case, "User's Logo Protect" is not
displayed.
f Entering the Password
When the password entry screen is displayed, enter the password using the
numeric buttons on the remote control.
Procedure
Restricting Operation (Operation Lock)
Do one of the following to lock the operation buttons on the control panel.
• Full Lock
All of the buttons on the control panel are locked. You cannot perform
any operations from the control panel, including turning the power on or
off.
• Operation Lock
All of the buttons on the control panel, except for the [Power] button,
are locked.
Enter the password by using the numeric buttons.
When you enter the correct password, projection begins.
Attention
• If an incorrect password is entered three times in succession, the
message "The projector's operation will be locked." is displayed
for about five minutes, and then the projector switches to standby
mode. If this happens, disconnect the power plug from the
electrical outlet and then reinsert it and turn the projector's power
back on. The projector displays the password entry screen again
so that you can enter the correct password.
• If you have forgotten the password, make a note of the "Request
Code: xxxxx" number that appears on the screen and contact the
nearest address provided in the Support and Service Guide.
sEpson Projector Contact List
• If you continue to repeat the above operation and input the wrong
password thirty times in succession, the following message is
displayed and the projector does not accept any more password
entries. "The projector's operation will be locked. Contact Epson
as described in your documentation." sEpson Projector Contact
List
This is useful at events or shows when you want to deactivate all buttons
and only project, or at schools when you want to limit button operation.
The projector can still be operated using the remote control.
Procedure
the [Menu] button and select "Settings" A Press
"Operation Lock" in the configuration menu.
s "Using the Configuration Menu" p.23
Using the remote control
Using the control panel
21
Security Functions
Anti-Theft Lock
Check the buttons you can use and the operations they perform in
the guide under the menu.
B Select either "Full Lock" or "Operation Lock".
As the projector is often setup on ceiling mounts and left in rooms
unattended, it is possible that someone may try and take the projector, so
the projector includes the following security devices.
• Security slot
The security slot is compatible with the Microsaver Security System
manufactured by Kensington. You can find details about the Microsaver
Security System on the Kensington homepage
http://www.kensington.com/.
• Security cable installation point
A commercially available theft-prevention wire lock can be passed
through the installation point to secure the projector to a desk or pillar.
f Installing the wire lock
"Yes" when the confirmation message is
C Select
displayed.
The control panel buttons are locked according to the setting you
chose.
q
You can release the control panel lock by one of the
following two methods.
• From the remote control, select "Off" from "Settings" "Operation Lock" in the configuration menu.
• When you press and hold down the [Enter] button on the
control panel for about seven seconds, a message is
displayed and the lock is released.
Pass an anti-theft wire lock through the installation point.
See the documentation supplied with the wire lock for locking
instructions.
Configuration Menu
This chapter explains how to use the configuration menu and its functions.
Using the Configuration Menu .......................... 23
List of Functions ................................................. 24
•
•
•
•
•
•
•
•
•
Image Menu (EMP-83H/822H Only) ..............................24
Image Menu (EMP-X5/S5 Only) .....................................25
Signal Menu (EMP-83H/822H Only) ..............................26
Signal Menu (EMP-X5/S5 Only) .....................................27
Settings Menu ....................................................................28
Extended Menu .................................................................29
Network Menu (EMP-83H/822H Only) ..........................31
Info Menu (Display Only).................................................34
Reset Menu ........................................................................35
Using the Configuration Menu
from the
A Selecting
top menu
from the
B Selecting
sub menu
23
the
C Changing
selected item
D Exit
Top menu
Guide
Sub menu (Settings)
For EMP-83H/822H/X5
For EMP-S5
Buttons used
Using the control panel
Select the setting to change
For EMP-83H/
822H/X5
For EMP-S5
Using the remote control
List of Functions
24
Image Menu (EMP-83H/822H Only)
Items that can be set vary depending on the image signal currently being projected as shown in the following screen shots. Setting details are saved for each
image signal.
Computer image
Sub Menu
Color Mode
Brightness
Contrastg
Color Saturation
Tint
Sharpness
Color Adjustment
Reset
Component videog/Composite videog/S-videog
Function
You can select the quality of the image to suit your surroundings. s p.14
You can adjust the image brightness.
You can adjust the difference between light and shade in the images.
You can adjust the color saturation for the images.
(Adjustment is only possible when NTSC signals are being input if you use composite video/S-video.)
You can adjust the image tint.
You can adjust the image sharpness.
You can make adjustments by choosing one of the following
Abs. Color Temp.: You can adjust the overall tint of the image. You can adjust tints in 10 stages from 5000 K to 10000 K. When a high value is
selected the image becomes tinged with blue, and when a low value is selected the image becomes tinged with red.
Red, Green, Blue: You can adjust the saturation of each color individually.
(This item cannot be selected if "sRGBg" is selected as the "Color Mode" setting in the "Image" menu.)
You can reset all adjustment values in the "Image" menu to their default settings. To return all menu items to their default settings, see s p.35
25
List of Functions
Image Menu (EMP-X5/S5 Only)
Items that can be set vary depending on the image signal currently being projected as shown in the following screen shots. Setting details are saved for each
image signal.
Computer image
Sub Menu
Color Mode
Brightness
Contrastg
Color Saturation
Tint
Sharpness
Color Temp.
Color Adjustment
Reset
Component videog/Composite videog/S-videog
Function
You can select the quality of the image to suit your surroundings. s p.14
You can adjust the image brightness.
You can adjust the difference between light and shade in the images.
You can adjust the color saturation for the images.
(Adjustment is only possible when NTSC signals are being input if you use composite video/S-video.)
You can adjust the image tint.
You can adjust the image sharpness.
You can adjust the overall tint of the image. When "High" is selected the image becomes tinged with blue, and when "Low" is selected the image
becomes tinged with red.
(This item cannot be selected if "sRGBg" is selected as the "Color Mode" setting in the "Image" menu.)
Red, Green, Blue: You can adjust the saturation of each color individually.
(This item cannot be selected if "sRGBg" is selected as the "Color Mode" setting in the "Image" menu.)
You can reset all adjustment values in the "Image" menu to their default settings. To return all menu items to their default settings, see s p.35
26
List of Functions
Signal Menu (EMP-83H/822H Only)
Items that can be set vary depending on the image signal currently being projected as shown in the following screen shots. Setting details are saved for each
image signal.
Computer image
Sub Menu
Auto Setup
Trackingg
Sync.g
Position
Progressiveg
Computer1 Input
Computer2 Input
Video Signal
Aspect
Reset
Component videog
Composite videog/S-videog
Function
You can select whether the image is automatically adjusted to the optimum state (On) or not (Off) when the input signal changes. s p.44
You can adjust computer images when vertical stripes appear in the images. s p.44
You can adjust computer images when flickering, fuzziness, or interference appear in the images. s p.44
You can adjust the display position up, down, left, and right so that all of the image is projected if a part of the image is missing.
(Component video can only be adjusted when 480i/576i signals are being input)
Off: IP conversion is carried out for each field in the screen. This is ideal for viewing images with a large amount of movement.
On: interlaceg (i) signals are converted into progressiveg (p) signals. This is ideal for viewing still images.
You can select the input signal from the Computer1 input port or Computer2 input port.
If set to "Auto" the input signal is set automatically according to the connected equipment.
If colors do not appear correctly when set to "Auto", select the appropriate signal according to the connected equipment.
If set to "Auto", video signals are recognized automatically. If interference appears in the image or a problem occurs such as no image is being
projected when set to "Auto", select the appropriate signal according to the connected equipment.
You can set the aspect ratiog for projected images. s p.16
You can reset all adjustment values in the "Signal" menu to their default settings, except for "Computer1 Input" and "Computer2 Input".
To return all menu items to their default settings, see s p.35
27
List of Functions
Signal Menu (EMP-X5/S5 Only)
Items that can be set vary depending on the image signal currently being projected as shown in the following screen shots. Setting details are saved for each
image signal.
Computer image
Sub Menu
Auto Setup
Trackingg
Sync.g
Position
Progressiveg
Computer Input
Video Signal
Aspect
Reset
Component videog
Composite videog/S-videog
Function
You can select whether the image is automatically adjusted to the optimum state (On) or not (Off) when the input signal changes. s p.44
You can adjust computer images when vertical stripes appear in the images. s p.44
You can adjust computer images when flickering, fuzziness, or interference appear in the images. s p.44
You can adjust the display position up, down, left, and right so that all of the image is projected if a part of the image is missing.
(Component video can only be adjusted when 480i/576i signals are being input)
Off: IP conversion is carried out for each field in the screen. This is ideal for viewing images with a large amount of movement.
On: interlaceg (i) signals are converted into progressiveg (p) signals. This is ideal for viewing still images.
You can select the input signal from the Computer input port.
If set to "Auto" the input signal is set automatically according to the connected equipment.
If colors do not appear correctly when set to "Auto", select the appropriate signal according to the connected equipment.
If set to "Auto", video signals are recognized automatically. If interference appears in the image or a problem occurs such as no image is being
projected when set to "Auto", select the appropriate signal according to the connected equipment.
You can set the aspect ratiog for projected images. s p.16
You can reset all adjustment values in the "Signal" menu to their default settings, except for "Computer Input".
To return all menu items to their default settings, see s p.35
28
List of Functions
Settings Menu
For EMP-83H/822H
Sub Menu
Keystone
Auto Keystone
(EMP-83H/822H/X5
only)
Zoom
(EMP-S5 only)
Operation Lock
Brightness Control
Volume
Remote Receiver
(EMP-83H/822H
only)
Test Pattern
(EMP-83H/822H
only)
Reset
For EMP-X5
For EMP-S5
Function
You can correct vertical keystone distortion in images.s Quick Start Guide
Performs automatic keystone correction.
(This can only be specified when "Front" is selected from "Extended" - "Projection".)
Adjusts the image size.s Quick Start Guide
Wide: Larger Tele: Smaller
You can use this to restrict operation of the projector's control panel. s p.20
You can set the lamp brightness to one of two settings.
Select "Low" if the images being projected are too bright such as when projecting images in a dark room or onto a small screen. When "Low" is
selected, the amount of electricity consumed and the lamp's operating life are changed as follows, and fan rotation noise during projection is
reduced. Electrical consumption: about a 35 W decrease, lamp life: about 1.5 times longer
You can adjust the volume.
You can limit the reception of the operation signal from the remote control.
When you want to prohibit operation by remote control, or if the remote receiver has a fluorescent light too close to it , you can make settings to
deactivate the remote receiver that you do not want to use or that is experiencing interference.
When the projector is setup, a test pattern is displayed so that you can adjust the projection without connecting other equipment. While the test
pattern is displayed you can perform zoom adjustments, focus adjustments, and keystone correction.
To cancel the test pattern, press the [Esc] button on the remote control or the control panel.
You can reset all adjustment values in the "Settings" menu to their default settings.
To return all menu items to their default settings, see s p.35
29
List of Functions
Extended Menu
For EMP-83H/822H
Sub Menu
Display
User's Logo*1
Projection
For EMP-X5/S5
For EMP-X5/S5 (Euro)
Function
You can make settings related to the projector's display.
Messages: You can set whether to display (On) or not display (Off) the source name when you change the input source, the color mode name
when you change the Color Mode, a message when no image signal is input, and so on.
Display Background*1: You can set the screen status for when no image signal is available to "Black", "Blue", or "Logo".
Startup Screen*1: You can set whether the startup screen (the image projected when starting the projector) is displayed (On) or not (Off).
A/V Mute*1: You can set the screen displayed during A/V Mute as "Black", "Blue", or "Logo".
You can change the user's logo that is displayed as a background and displayed during A/V Mute. s p.57
You can choose one of the following settings according to the way the projector is setup. s p.49
Front" "Front/Ceiling" "Rear" "Rear/Ceiling"
You can change the setting as follows by pressing down the [A/V Mute] button on the remote control for about five seconds.
Front" W "Front/Ceiling"
Rear" W "Rear/Ceiling"
List of Functions
Sub Menu
Operation
30
Function
Direct Power On: You can set whether Direct Power On is enabled (On) or disabled (Off).
When it is set to "On" and the projector power cable is connected to an electrical outlet, be aware that sudden surges of electricity may cause the
projector to turn on automatically.
Sleep Mode: When set to "On", this turns off the power automatically when no image signal is input and no operations are performed. Sleep
mode is set to (On) at the time of purchase.
Sleep Mode Time: When Sleep Mode is set to "On", you can set how long the projector should wait before turning off the power from 1 to
30 minutes.
Lens Cover Timer: When set to "On", this turns off the power automatically 30 minutes after the lens cover is closed. Lens Cover Timer is set to
(On) at the time of purchase.
High Altitude Mode: Set this to "On" when using the projector above an altitude of 1500 m.
Standby Mode
You can use network monitoring and control functions while the projector is in standby mode when this is set to "Network On".
(EMP-83H/822H
You can use SNMPg to monitor and control the status of the projector over the network, or by using the "EMP Monitor" software supplied with
only)
this product.
Link 21Lg
You can set whether to use the utility software EMP Link 21L (On) or not (Off). Set this to "On" and use it after installing the USB
(EMP-X5/S5 only)
communication driver.
Language
You can set the language for message displays.
Reset
You can reset "Display*1" and "Operation*2" in the "Extended" menu to their default settings.
To return all menu items to their default settings, see s p.35
*1 When "User's Logo Protect" is set to "On" in "Password Protect", settings concerning user's logo cannot be changed. You can make changes after setting "User's
Logo Protect" to "Off". s p.19
Depending on the area of purchase, the User's Logo function may not be available for EMP-X5/S5. In that case, "User's Logo" is not displayed.
*2 Except for "High Altitude Mode".
31
List of Functions
Network Menu (EMP-83H/822H Only)
When "Network Protect" is set to "On" in "Password Protect", a message is displayed and the settings cannot be changed. You can make changes after
setting "Network Protect" to "Off". s p.19
Sub Menu
Wired LAN
PJLink Password
Web Control
Password
Function
You can make network settings.
DHCP: You can set whether to use DHCP (On) or not (Off).
If this is set to "On" you cannot set any more addresses.
IP Address: You can input the IP address assigned to the projector.*1
You can enter a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used.
0.0.0.0, 0.x.x.x, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
Subnet Mask: You can input the Subnet Mask for the projector.*1
You can enter a number from 0 to 255 in each field of the address. However, the following subnet masks cannot be used.
0 to 254.x.x.x. 255.255.255.255
Gateway Address: You can input the IP address for the gateway for the projector.*1
You can enter a number from 0 to 255 in each field of the address. However, the following gateway addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
MAC Address: You can input the MAC Address for the projector.
Enter a password to use when you access the projector using compatible PJLink software.*1 s p.69
You can enter up to 32 alphanumeric characters.
Enter a password to use when making settings and controlling the projector using Web control.*1 You can enter up to 8 alphanumeric characters.
Web control is a computer function that allows you to set up and control the projector by using the Web browser on a computer on which EMP
Monitor is running. sEMP Monitor Operation Guide
32
List of Functions
Sub Menu
SNMPg
Function
You can make SNMP settings.
Trap IP Address 1/Trap IP Address 2: You can register up to two IP addresses for the SNMP trap notification destination.
The IP address registered in "Trap IP Address 2" is used when the IP address in "Trap IP Address 1" cannot be accessed.
To use SNMP to monitor the projector, you need to install the SNMP manager program on your computer. SNMP should be managed by a
network administrator.
Mail
When this is set, you are notified by e-mail if a problem or warning occurs with the projector.*2
Mail Notification: You can set whether to be notified by mail (On) or not (Off).
SMTP Server: You can input the IP address for the SMTP server for the projector.*1
You can enter a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used.
127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
Port Number: You can input the port number for the SMTP server.*1
The initial value is 25. You can input numbers between 1 to 65535.
Destination Address 1/Destination Address 2/Destination Address 3: You can enter*1 the destination mail address and the contents of the
message to receive notification when a problem or warning occurs. You can register up to three destinations. You can enter up to 32 single-byte
alphanumeric characters for the mail addresses.
Projector Name
You can enter a name for the projector. When connected to a network, this name is used to identify the projector.
Reset
You can reset all adjustment values in the "Network" menu to their default settings.
To return all menu items to their default settings, see s p.35
*1 When inputting numbers and passwords, the following software keyboard is displayed. Tilt the [u], [d], [l], and [r] buttons on the remote control to move the
cursor to the target key, and press the [Enter] button to input. After entering characters, press [Finish] on the keyboard to confirm your entry. Press [Cancel] on the
keyboard to cancel your input.
Each time this key is
selected, it sets and
changes between upper
case and lower case
letters.
Each time this key is
selected, it sets and
changes the symbol
keys for the section
enclosed by the frame.
33
List of Functions
*2 When the Mail Notification function is set to "On" and a problem or warning occurs with a projector, the following mail is sent.
Subject: EPSON Projector
First line: The name of the projector where the problem has occured
Second line: The IP address set for the projector where the problem has occured
Third line and on: Details of the problem
The details of the problem are listed line by line. The following table explains the details shown in the message.
For details on dealing with problems, see "Reading the Indicators".s p.38
Message
Internal error
Fan related error
Sensor error
Lamp cover is open.
Lamp timer failure
Lamp out
Internal temperature error
High-speed cooling in
progress
Lamp replacement
notification
Cause
Internal Error
Fan Error
Sensor Error
Lamp Cover Open
Lamp Failure
Lamp Error
High Temp Error
(Overheating)
High Temp Warning
Replace Lamp
No signal
No image signal is being input to the
No-signal
projector. Check the connection status
and the power supply to connected
equipment.
A (+) or (-) will appear at the start of the message.
(+): A projector problem has occured
(-): A projector problem has been dealt with
34
List of Functions
Info Menu (Display Only)
Lets you check the status of the image signals being projected and the status of the projector. Items displayed vary depending on the image signal currently
being projected as shown in the following screen shots.
Computer image/Component videog
Sub Menu
Lamp Hours
Composite videog/S-videog
Function
time*.
You can display the cumulative lamp operating
When it reaches the lamp warning time, the characters are displayed in yellow.
Source
You can display the input port name for the connected equipment currently being projected.
Input Signal
You can display the content of "Computer1" or "Computer2" set in the "Signal" menu according to the "Source".
Resolution
You can display the input resolution.
Video Signal
You can display the content of "Video Signal" set in the "Signal" menu.
Refresh Rateg
You can display the refresh rate.
Syncg Info
You can display the image signal information.
This information may be needed if service is required.
Status
This is information about problems that have occurred on the projector.
This information may be needed if service is required.
* The cumulative use time is displayed as "0H" for the first 10 hours. After 10 hours or more, one hour is added for each subsequent hour.
35
List of Functions
Reset Menu
For EMP-83H/822H
Sub Menu
Reset All
(EMP-83H/822H
only)
Reset All
(EMP-X5/S5 only)
Reset Lamp Hours
For EMP-X5/S5
Function
You can reset all items in all menus to their default settings.
The following items are not reset to their defaults: "Computer1 Input", "Computer2 Input", "User's Logo", all items in "Network" menu, "Lamp
Hours", and "Language".
You can reset all items in all menus to their default settings.
The following items are not reset to their defaults: "Computer Input", "Zoom" (EMP-S5 only), "User's Logo*", "Lamp Hours", and "Language".
You can clear the cumulative Lamp Hours use time, and return it to "0H". Reset it when you replace the lamp.
* Depending on the area of purchase, the User's Logo function may not be available for EMP-X5/S5. In that case, "User's Logo" is not displayed.
Troubleshooting
This chapter describes how to identify problems and what to do if a problem is found.
Using the Help..................................................... 37
Problem Solving ................................................. 38
• Reading the Indicators......................................................38
t Power indicator lights red ..........................................................39
i o Indicator is lit or flashing orange...........................................40
• When the Indicators Provide No Help ............................41
Problems relating to images ...........................................................42
Problems when projection starts.....................................................46
Other problems ...............................................................................46
Using the Help
37
If a problem occurs with the projector, Help uses on-screen displays to
assist you in solving the problem.
C Confirm the selection.
Using the remote control
Using the control panel
Procedure
A Press the [Help] button.
The help screen is displayed.
Using the remote control
Using the control panel
Questions and solutions are displayed as shown on the screen
below.
Press the [Help] button to exit Help.
B Select a menu item.
q
Using the remote control
Using the control panel
If Help does not provide a solution to the problem, refer to
"Problem Solving" (s p.38).
Problem Solving
38
If you are having a problem with the projector, first check the projector's indicators and refer to "Reading the Indicators" below.
If the indicators do not show clearly what the problem might be, refer to "When the Indicators Provide No Help". s p.41
Reading the Indicators
The projector is provided with the following three indicators that indicate the operating status of the projector.
Indicates the operating status.
Orange : Standby condition
When the [Power] button is pressed in this condition, projection starts.
Green (Flashing):Warm-up in progress
Warm-up time is about 30 seconds. After warm-up is complete, the indicator stops flashing.
Green : Projection in progress
Indicates the projection lamp status.
Indicates the internal temperature status.
Refer to the following table to see what the indicators mean and how to remedy problems that they indicate.
If all indicators are off, check that the power cable is connected correctly and that the power is being supplied normally.
Sometimes, when the power cable is unplugged, the t indicator remains lit for a short period which is not a fault.
39
Problem Solving
f t Power indicator lights red
Problem
: Lit
Status
Red
: Flashing:
: Off
Cause
Internal Error
Remedy or Status
Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest
address provided in the Support and Service Guide. sEpson Projector Contact List
Fan Error
Sensor Error
Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest
address provided in the Support and Service Guide. sEpson Projector Contact List
High Temp Error
(overheating)
The lamp turns off automatically and projection stops. Wait for about five minutes. After about five minutes the projector
switches to standby mode, so check the following two points.
• Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
• If the air filter is clogged, clean or replace it. s p.50, 56
If the error continues after checking the points above, stop using the projector, disconnect the power cable from the
electrical outlet, and contact your local dealer or the nearest address provided in the Support and Service Guide. sEpson
Projector Contact List
When using at an altitude of 1500 m or more, set "High Altitude Mode" to "On". s p.30
Check the following two points.
• Take out the lamp and check if it is cracked. s p.53
• Clean the air filter. s p.50
If it is not cracked - Re-fit the lamp and turn on the power.
If the error continues - Replace the lamp with a new lamp and turn on the power.
If the error continues - Stop using the projector, disconnect the power cable from the electrical outlet, and contact
your local dealer or the nearest address provided in the Support and Service Guide.
sEpson Projector Contact List
If it is cracked - Replace it with a new lamp, or contact your local dealer for further advice. If replacing the lamp
yourself, be careful to avoid pieces of broken glass (you cannot continue projecting until the lamp is replaced). sEpson
Projector Contact List
Check that the lamp cover and the lamp are securely installed. s p.53
If the lamp cover or the lamp is not securely installed, the lamp does not switch on.
When using at an altitude of 1500 m or more, set "High Altitude Mode" to "On". s p.30
Red
Red
Red
Red
Red
Red
Red
Red
Lamp Error
Lamp Failure
Lamp Cover Open
40
Problem Solving
f i o Indicator is lit or flashing orange
Warning
: Lit
Status
Red
: Flashing
: Off
: Varies according to the projector status
Cause
High Temp Warning
Remedy or Status
(This is not a problem. However, if the temperature rises too high again, projection stops automatically.)
• Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
• If the air filter is clogged, clean or replace it. s p.50, 56
Replace Lamp
Replace it with a new lamp. s p.53
If you continue to use the lamp after the replacement period has passed, the possibility that the lamp may explode
increases. Replace it with a new lamp as soon as possible.
Orange
Orange
q
• If the projector is not operating properly, even though the indicators are all showing normal, refer to "When the Indicators Provide No
Help" (s p.41).
• If an indicator is displaying a status not described in the tables, contact your local dealer or the nearest address provided in the Support and
Service Guide. sEpson Projector Contact List
41
Problem Solving
When the Indicators Provide No Help
If any of the following problems occur and the indicators do not offer a
solution, refer to the pages given for each problem.
Problems relating to images
f No images appear s p.42
Projection does not start, the projection area is completely black, the
projection area is completely blue, and so on.
f Moving images are not displayed s p.42
Moving images being projected from a computer appear black and
nothing is projected.
f Projection stops automatically s p.42
f The message "Not supported." is displayed s p.43
f The message "No Signal." is displayed s p.43
f Images are fuzzy or out of focus s p.43
f Interference or distortion appears in images s p.44
Problems such as interference, distortion, or black & white checked
patterns appear.
f The image is truncated (large) or small, or the aspect is not
suitable s p.44
Only part of the image is displayed, or the height and width ratios of the
image are not correct, and so on.
f Image colors are not right s p.45
The whole image appears purplish or greenish, images are black & white,
colors appear dull, and so on.
(Computer monitors and LCD screens have different color reproduction
performance, so the colors projected by the projector and the colors
appearing on the monitor may not necessarily match, but this is not a sign
of a problem.)
f Images appear dark s p.45
f Nothing appears on the external monitor s p.45
Problems when projection starts
f Power does not turn on s p.46
Other problems
f There is no audio or the audio is
too low s p.46
f The remote control does not work
s p.47
f Mail is not received even if a
problem occurs with the projector
(EMP-83H/822H Only) s p.47
42
Problem Solving
f Problems relating to images
f No images appear
Check
Did you press the [Power] button?
Are the indicators switched off?
Is A/V Mute active?
Is the A/V mute slide closed?
Are the configuration menu settings correct?
Is the projected image completely black?
Remedy
Press the [Power] button to turn the power on.
The power cable is not connected correctly or power is not being supplied normally.
Connect the projector's power cable correctly. s Quick Start Guide
Check that your electrical outlet or power source is functioning correctly.
Press the [A/V Mute] button on the remote control to cancel A/V Mute. s p.15
Open the A/V mute slide.
Reset all of the settings. s"Reset"-"Reset All" p.35
Some input images, such as screen savers, may be completely black.
Only when projecting computer images
Is the image signal format setting correct?
Change the setting according to the signal for the connected equipment. s"Signal"-"Video Signal" p.26
Only when projecting images from a video source
f Moving images are not displayed
Check
Is the computer's image signal being output to the LCD and
the monitor?
Remedy
Change the image signal to external output only. s Check your computer's documentation.
Only when projecting images from a laptop
computer or a computer with a built-in LCD screen
f Projection stops automatically
Check
Is "Sleep Mode" set to "On"?
Remedy
Press the [Power] button to turn the power on. If you do not want to use "Sleep Mode", change the setting to
"Off". s"Extended"-"Operation"-"Sleep Mode" p.30
43
Problem Solving
f The message "Not supported." is displayed
Check
Is the image signal format setting correct?
Remedy
Change the setting according to the signal for the connected equipment. s"Signal"-"Video Signal" p.26
Only when projecting images from a video source
Do the image signal resolution and the refresh rate
correspond to the mode?
Refer to the computer's documentation for how to change the image signal resolution and the refresh rate
output from the computer. s "List of Supported Monitor Displays" p.70
Only when projecting computer images
f The message "No Signal." is displayed
Check
Are the cables connected correctly?
Is the correct input port selected?
Is the power for the computer or video source turned on?
Are the image signals being output to the projector?
Remedy
Check that all the cables required for projection are securely connected. s Quick Start Guide
Change the image by pressing the [Source Search] button on the remote control or the control panel.s p.13
Turn the power on for the equipment.
If the image signals are only being output to the computer's LCD monitor or to the accessory monitor, you
need to change the output to an external destination as well as the computer's own monitor. For some
Only when projecting images from a laptop
computer or a computer with a built-in LCD screen computer models, when the image signals are output externally, they no longer appear on the LCD monitor
or accessory monitor. sComputer's documentation, under a title such as "External output" or "Connecting
an external monitor".
If the connection is made while the power of the projector or computer is already turned on, the function
[Fn] key that changes the computer's image signal to external output may not work. Turn the power for the
computer and the projector off and then back on again. s Quick Start Guide
f Images are fuzzy or out of focus
Check
Is the focus adjusted correctly?
Is the projector at the correct distance?
Is the Keystone adjustment value too large?
Has condensation formed on the lens?
Remedy
Turn the focus ring to adjust the focus. s Quick Start Guide
For EMP-83H/822H/X5, the recommended projection distance for Wide ranges from 84 to 867 cm, and for
Tele from 101 to 1041 cm. For EMP-S5, the recommended projection distance ranges from 87 to 1050 cm.
Setup within this range. s p.59
Lower the projection angle to reduce the amount of keystone correction. s Quick Start Guide
If the projector is suddenly taken from a cold environment to a warm environment, or if sudden ambient
temperature changes occur, condensation may form on the surface of the lens, and this may cause the images
to appear fuzzy. Set the projector up in the room about one hour before it is used. If condensation forms on
the lens, turn the projector off and wait for the condensation to disappear.
44
Problem Solving
f Interference or distortion appear in images
Check
Is the image signal format setting correct?
Remedy
Change the setting according to the signal for the connected equipment. s"Signal"-"Video Signal" p.26
Only when projecting images from a video source
Are the cables connected correctly?
Is an extension cable being used?
Is the correct resolution selected?
Only when projecting computer images
Are the "Sync.g" and "Trackingg" settings adjusted
correctly?
Only when projecting computer images
Check that all the cables required for projection are securely connected. s Quick Start Guide
If an extension cable is used, electrical interference may affect the signals. Use the cables supplied with the
projector to check if the cables you are using may be causing the problem.
Set the computer so that the signals being output are compatible with the projector.
s "List of Supported Monitor Displays" p.70 sComputer documentation
Press the [Auto] button on the remote control or the [Enter] button on the control panel to perform automatic
adjustment. If the images are not adjusted correctly after using automatic adjustment, you can make the
adjustments from "Sync." and "Tracking" in the configuration menu.
s"Signal"-"Tracking", "Sync." p.26
f The image is truncated (large) or small, or the aspect is not suitable
Check
Is a wide panel computer image being projected?
Only when projecting computer images
Is the image still being enlarged by E-Zoom?
Is "Position" adjusted correctly?
Is the computer set for dual display?
Only when projecting computer images
Is the correct resolution selected?
Only when projecting computer images
Remedy
Press the [Aspect] button on the remote control to change the aspect mode in the order of "Normal", "4:3",
and "16:9". Change the aspect mode according to the resolution.
Press the [Esc] button on the remote control to cancel E-Zoom. s p.17
Press the [Auto] button on the remote control or the [Enter] button on the control panel to perform automatic
adjustment of the computer image being projected. If the images are not adjusted correctly after using
automatic adjustment, you can make the adjustments from "Position" in the configuration menu.
Apart from computer image signals, you can adjust other signals while projecting by adjusting "Position" in
the configuration menu. s"Signal"-"Position" p.26
If dual display is activated in the "Display Properties" of the computer's control panel, only about half of the
image on the computer screen is projected. To display the entire image on the computer screen, turn off the
dual display setting. sComputer video driver documentation
Set the computer so that the signals being output are compatible with the projector.
s "List of Supported Monitor Displays" p.70 sComputer documentation
45
Problem Solving
f Image colors are not right
Check
Do the input signal settings match the signals from the
connected device?
Is the image brightness adjusted correctly?
Are the cables connected correctly?
Is the "Contrastg" setting adjusted correctly?
Is the color adjusted correctly?
Are the color saturation and tint adjusted correctly?
Only when projecting images from a video source
Remedy
Change the following settings according to the signal for the connected equipment.
When projecting images from equipment connected to Computer1, Computer, or Computer2 Input,
see s "Signal"-"Computer1/2 Input" p.26
When projecting images from equipment connected to Video or S-Video,
see s"Signal"-"Video Signal" p.26
Adjust the "Brightness" setting in the configuration menu. s"Image"-"Brightness" p.24
Check that all the cables required for projection are securely connected. s Quick Start Guide
Adjust the "Contrast" setting in the configuration menu. s"Image"-"Contrast" p.24
Adjust the "Color Adjustment" setting in the configuration menu. s"Image"-"Color Adjustment" p.24
Adjust the "Color Saturation" and "Tint" settings in the configuration menu.
s"Image"-"Color Saturation", "Tint" p.24
f Images appear dark
Check
Are the image brightness and luminance adjusted correctly?
Is the "Contrastg" setting adjusted correctly?
Is the lamp due for replacement?
Remedy
Adjust the "Brightness" and "Brightness Control" settings in the configuration menu.
s"Image"-"Brightness" p.24 s"Settings"-"Brightness Control" p.28
Adjust the "Contrast" setting in the configuration menu.
s"Image"-"Contrast" p.24
When the lamp is nearly ready for replacement, the images become darker and the color quality becomes
poorer. When this happens, replace the lamp with a new lamp. s p.53
f Nothing appears on the external monitor
Check
Are images from a port other than the Computer1 or
Computer Input port being projected?
Remedy
The only images that can be displayed on an external monitor are computer images from the Computer1 or
Computer Input port. s p.61
46
Problem Solving
f Problems when projection starts
f Power does not turn on
Check
Did you press the [Power] button?
Are the indicators switched off?
Do the indicators turn on and off when the power cable is
touched?
Is the operation lock set to "Full Lock"?
Is the correct setting for the remote receiver selected?
(EMP-83H/822H only)
Was the power cable plugged back in immediately after
Direct Power Off, or is the breaker turned off?
(EMP-83H/822H only)
Remedy
Press the [Power] button to turn the power on.
The power cable is not connected correctly or power is not being supplied normally.
Connect the projector's power cable correctly. s Quick Start Guide
Check that your electrical outlet or power source is functioning correctly.
There is probably a poor contact in the power cable, or the power cable may be defective. Reinsert the power
cable. If this does not solve the problem, stop using the projector, disconnect the power cable from the
electrical outlet, and contact your local dealer or the nearest address provided in the Support and Service
Guide. sEpson Projector Contact List
When you press and hold down the [Enter] button on the control panel for about seven seconds, a message is
displayed and the lock is released. s p.20
Check the "Remote Receiver" in the configuration menu. s"Settings"-"Remote receiver" p.28
When the operation to the left is performed when "Direct Power On" is set to "On", the power may not turn
back on. Press the [Power] button to turn the power back on.
f Other problems
f There is no audio or the audio is too low
Check
Is the audio source connected correctly?
Is the volume adjusted to the minimum setting?
Is A/V Mute active?
Is the audio cable's specification "No resistance"?
Remedy
Check that the cable is connected to the Audio port.
Adjust the volume so that sound can be heard. s Quick Start Guide
Press the [A/V Mute] button on the remote control to cancel A/V Mute. s p.15
When using a commercially available audio cable, make sure it is labelled "No resistance".
Problem Solving
47
f The remote control does not work
Check
Remedy
Is the remote control light-emitting area pointing towards the Point the remote control towards the remote receiver.
remote receiver on the projector when it is operated?
The operating angle for the remote control is about 30 horizontally, and about 15 vertically.
s Quick Start Guide
Is the remote control too far from the projector?
The operating range for the remote control is about 6 m. s Quick Start Guide
Is direct sunlight or strong light from fluorescent lamps
Set the projector up in a location where strong light does not shine onto the remote receiver. For EMP-83H/
shining onto the remote receiver?
822H, set the remote receiver to "Off" from "Remote Receiver" in the configuration menu. s"Settings""Remote receiver" p.28
Is the correct setting for the remote receiver selected?
Check the "Remote Receiver" in the configuration menu. s"Settings"-"Remote receiver" p.28
(EMP-83H/822H only)
Are the batteries dead or have the batteries been inserted
Make sure the batteries are inserted correctly or replace the batteries with new ones if necessary. s p.51
correctly?
Was a remote control button pressed for more than
If any of the buttons on the remote control are pressed down for more than 30 seconds, the remote control
30 seconds?
stops sending signals (remote control's sleep mode). When the button is released, normal remote control
operation resumes. This can prevent the batteries from running down accidentally because Sleep Mode
operates when the remote control is stored in a bag or if an object is placed on top of it.
f Mail is not received even if a problem occurs with the projector (EMP-83H/822H Only)
Check
Is "Standby Mode" set to "Network On"?
Remedy
To use the Mail Notification function when the projector is in standby, set "Network On" from "Standby
Mode" in the configuration menu. s"Extended"-"Standby Mode" p.30
Did a fatal problem occur and the projector come to a sudden When the projector comes to a sudden stop, mail cannot be sent.
stop?
If the problem continues, contact your local dealer or the nearest address provided in the Support and
Service Guide. sEpson Projector Contact List
Is power being supplied to the projector?
Check that your electrical outlet or power source is functioning correctly.
Is the LAN cable connected correctly?
Check that the LAN cable is connected correctly. Reconnect it if it is not connected or it is not connected
correctly. s p.62
Is "Mail" set correctly in the configuration menu?
Mail notification of problems is sent according to the "Mail" settings in the configuration menu. Check if it
is set correctly. s"Network Menu"-"Mail Menu" p.32
Appendices
This chapter provides information on maintenance procedures to ensure the best level of performance from the
projector for a long time to come.
Installation Methods ........................................... 49
Cleaning............................................................... 50
Optional Accessories and Consumables .........64
Optional accessories....................................................................... 64
Consumables .................................................................................. 64
• Cleaning the Projector's Surface .....................................50
• Cleaning the Lens..............................................................50
• Cleaning the Air Filter and Air Intake Vent ..................50
Glossary...............................................................65
ESC/VP21 Commands ........................................67
Replacing Consumables .................................... 51
• Command List .................................................................. 67
• Cable Layouts ................................................................... 67
• Replacing the Remote Control Batteries ........................51
• Replacing the Lamp ..........................................................52
Lamp replacement period...............................................................52
How to replace the lamp.................................................................53
Resetting the lamp operating time..................................................55
• Replacing the Air Filter....................................................56
Air filter replacement period ..........................................................56
How to replace the air filter............................................................56
Saving a User's Logo ......................................... 57
Screen Size and Distance .................................. 59
• EMP-83H/822H/X5 ...........................................................59
• EMP-S5 ..............................................................................60
Connecting to External Equipment ................... 61
• Connecting to an External Monitor ................................61
• Connecting to External Speakers
(EMP-83H/822H Only) .....................................................61
Connecting a LAN Cable
(EMP-83H/822H Only) ......................................... 62
Connecting a USB Cable (EMP-X5/S5 Only) .... 63
Serial connection (EMP-83H/822H Only)..................................... 67
• Connecting a USB (EMP-X5/S5 Only) ........................... 68
• USB Connection Setup ..................................................... 68
PJLink (EMP-83H/822H Only).............................69
Non-compatible commands ........................................................... 69
Input names defined by PJLink and corresponding projector
connectors.................................................................................. 69
Manufacturer name displayed for "Manufacture name
information query" .................................................................... 69
Model name displayed for "Product name information query" ..... 69
List of Supported Monitor Displays ..................70
Computer image............................................................................. 70
Component Video .......................................................................... 70
Composite video/S-video............................................................... 70
Specifications......................................................71
Appearance..........................................................75
Index.....................................................................76
Installation Methods
The projector supports the following four different projection methods.
Warning
• A special method of installation is required when suspending the
projector from a ceiling (ceiling mount). If it is not installed
correctly, it could fall causing an accident and injury.
• If you use adhesives on the ceiling mount to prevent the screws
from loosening, or if you use things such as lubricants or oils on
the projector, the projector case may crack causing it to fall from
its ceiling mount. This could cause serious injury to anyone under
the ceiling mount and could damage the projector.
When installing or adjusting the ceiling mount, do not use
adhesives to prevent the screws from loosening and do not use oils
or lubricants and so on.
49
• Project images from in front
of the screen.
(Front projection)
• Project images from behind a
translucent screen.
(Rear projection)
• Suspend the projector from
the ceiling and project images
from in front of the screen.
(Front/Ceiling projection)
• Suspend the projector from
the ceiling and project images
from behind a translucent
screen.
(Rear/Ceiling projection)
Attention
Do not use the projector on its side. This may cause malfunctions to
occur.
q
• An optional ceiling mount is required when suspending
the projector from a ceiling.
s p.64
• You can change the setting as follows by pressing down the
[A/V Mute] button on the remote control for about five
seconds.
"Front" W "Front/Ceiling"
Set "Rear" or "Rear/Ceiling" in the configuration menu.
s p.29
Cleaning
You should clean the projector if it becomes dirty or if the quality of
projected images starts to deteriorate.
Cleaning the Projector's Surface
Clean the projector's surface by wiping it gently with a soft cloth.
If the projector is particularly dirty, moisten the cloth with water
containing a small amount of neutral detergent, and then firmly wring the
cloth dry before using it to wipe the projector's surface.
50
Attention
If dust collects on the air filter it can cause the internal temperature
of the projector to rise, and this can lead to problems with operation
and shorten the optical engine's service life. Clean the air filter
immediately when the message is displayed.
Attention
Do not use volatile substances such as wax, alcohol, or thinner to
clean the projector's surface. The quality of the case may change or
become discolored.
Cleaning the Lens
Use a commercially available cloth for cleaning glasses to gently wipe the
lens.
Attention
Do not rub the lens with harsh materials or subject the lens to
shocks, as it can easily become damaged.
Cleaning the Air Filter and Air Intake Vent
Clean the air filter and the air intake vent when the following message is
displayed.
"The projector is overheating. Make sure nothing is blocking the air vent,
and clean or replace the air filter." s "How to replace the air filter" p.56
q
• If a message is frequently displayed, even after cleaning, it
is time to replace the air filter. Replace it with a new air
filter. s p.56
• It is recommended that you clean these parts at least once
every three months. Clean them more often than this if
using the projector in a particularly dusty environment.
Replacing Consumables
This section explains how to replace the remote control batteries, the
lamp, and the air filter.
51
B Replace the old batteries with new batteries.
Caution
Replacing the Remote Control Batteries
If delays in the responsiveness of the remote control occur or if it does not
operate after it has been used for some time, it probably means that the
batteries are becoming flat. When this happens, replace them with new
batteries. Have two spare AA-size manganese dry batteries ready to use
when required.
Check the positions of the (+) and (-) marks inside the battery
holder to ensure the batteries are inserted the correct way.
Attention
Make sure you read the Safety Instructions/Support and Service
Guide before handling the batteries. sSafety Instructions
C Replace the battery cover.
Press the battery cover until it clicks into place.
Procedure
A Remove the battery cover.
While pushing the battery cover catch, lift the cover up.
Catch
52
Replacing Consumables
Replacing the Lamp
Attention
f Lamp replacement period
It is time to replace the lamp when:
• The message "Replace the lamp." is displayed.
A message is displayed.
• The lamp indicator flashes orange.
Flashing orange
• The projected image gets darker or starts to deteriorate.
• The lamp replacement message is set to appear after the following
time periods in order to maintain the initial brightness and quality
of the projected images. s "Brightness Control" p.28
·When used continually at high brightness: About 2900 hours
·When used continually at low brightness: About 3900 hours
• If you continue to use the lamp after the replacement period has
passed, the possibility that the lamp may explode increases. When
the lamp replacement message appears, replace the lamp with a
new one as soon as possible, even if it is still working.
• Depending on the characteristics of the lamp and the way it has
been used, the lamp may become darker or stop working before
the lamp warning message appears. You should always have a
spare lamp ready in case it is needed.
53
Replacing Consumables
f How to replace the lamp
Warning
• When replacing the lamp because it has stopped illuminating,
there is a possibility that the lamp may be broken.
If replacing the lamp of a projector which has been installed on
the ceiling, you should always assume that the lamp is broken,
and you should stand to the side of the lamp cover, not underneath
it. Remove the lamp cover gently. Small pieces of glass may fall
out when the lamp cover is opened. If pieces of glass get into your
eyes or mouth, seek medical advice immediately.
Caution
• When replacing the lamp because it has stopped illuminating,
there is a possibility that the lamp may be broken.
Wait until the lamp has cooled down sufficiently before removing
the lamp cover. If the lamp is still hot, burns or other injuries may
result. It takes about one hour after the power has been turned off
for the lamp to be cool enough.
Procedure
you turn off the projector's power and the
A After
confirmation buzzer beeps twice, disconnect the
power cable.
until the lamp has cooled down, then remove
B Wait
the lamp cover.
Loosen the lamp cover fixing screw with the screwdriver supplied
with the new lamp or a + head screwdriver. Then slide the lamp
cover straight forward and lift it to remove.
54
Replacing Consumables
C Loosen the two lamp fixing screws.
D Take out the old lamp.
If the lamp is cracked, replace it with a new lamp, or contact your
local dealer for further advice. sEpson Projector Contact List
E Install the new lamp.
Insert the new lamp along the guide rail in the correct direction so
that it fits in place, push down firmly at the location marked
"PUSH", and once it is fully inserted tighten the two screws.
Replacing Consumables
F Replace the lamp cover.
Attention
• Make sure you install the lamp securely. If the lamp cover is
removed, the lamp turns off automatically as a safety precaution.
If the lamp or the lamp cover is not installed correctly, the lamp
does not turn on.
• This product includes a lamp component that contains mercury
(Hg). Please consult your local regulations regarding disposal or
recycling. Do not dispose of it with normal waste.
f Resetting the lamp operating time
The projector records how long the lamp is turned on and a message and
indicator notify you when it is time to replace the lamp. After replacing
the lamp, make sure you reset the lamp hours in the configuration menu.
s p.35
q
Only reset the lamp operating time after the lamp has been
replaced. Otherwise the lamp replacement period is not
indicated correctly.
55
56
Replacing Consumables
Replacing the Air Filter
C Install the new air filter.
Slide the air filter in from the outside and push until it clicks into
place.
f Air filter replacement period
It is time to replace the air filter when:
• The air filter is ripped.
• The message is displayed even though the air filter has been
cleaned.
f How to replace the air filter
The air filter can be replaced even when the projector is suspended from a
ceiling.
Procedure
you turn off the projector's power and the
A After
confirmation buzzer beeps twice, disconnect the
power cable.
B Remove the air filter.
Put your finger into the recess of the air filter and slide it forward to
remove it.
q
Dispose of used air filters properly in accordance with your
local regulations. Do not dispose of it with normal waste.
Material quality of the frame section: Polycarbonate, ABS
resin
Material quality of the filter section: Polyurethane form
Saving a User's Logo
You can save the image that is currently being projected as a user's
logo.
Depending on the area of purchase, the User's Logo function may not
be available for EMP-X5/S5. In that case, the user's logo cannot be
saved.
q
57
the configuration menu, select "Extended"B In"User's
Logo".
s "Using the Configuration Menu" p.23
Check the buttons you can use and the operations they perform in
the guide under the menu.
When a user's logo is saved, the previous user's logo is
erased.
Procedure
the image you want to use as the user's
A Project
logo, and then press the [Menu] button.
Using the remote control
Using the control panel
q
• If "User's Logo Protect" from "Password Protect" is set
to "On", a message is displayed and the user's logo
cannot be changed. You can make changes after setting
"User's Logo Protect" to "Off". s p.19
• If "User's Logo" is selected when Keystone, E-Zoom,
Aspect, or Progressive are being performed, the function
currently being performed is cancelled.
"Choose this image as the User's Logo?" is
C When
displayed, select "Yes".
q
When you press the [Enter] button on the remote control or
the control panel, the screen size may change as it changes
to the resolution of the image signal.
58
Saving a User's Logo
the box to select the part of the image to use
D Move
as the user's logo.
Using the remote control
Using the control panel
"Select this image?" is displayed, select
E When
"Yes".
the zoom factor from the zoom setting
F Select
screen.
the message "Save this image as the User's
G When
Logo?" is displayed, select "Yes".
The image is saved. After the image has been saved, the message
"Completed" is displayed.
q
q
You can save at up to 400 ^ 300 dots in size.
• Saving the user's logo may take about 15 seconds. Do not
use the projector or any connected equipment while it is
saving. This may cause malfunctions to occur.
• Once a user's logo has been saved, the logo cannot be
returned to the factory default.
Screen Size and Distance
59
EMP-83H/822H/X5
See the following table to choose the best position for your projector. The values are only a guide.
Units: cm (in.)
Projection Distance U
4:3 Screen Size
Offset V
16:9 Screen Size
Minimum Maximum
30"
40"
50"
60"
80"
100"
120"
150"
200"
300"
(Wide) to (Tele)
61 ^ 46 (24 ^ 18)
84 to 101 (33 to 40)
81 ^ 61 (32 ^ 24)
113 to 136 (44 to 53)
100 ^ 76 (39 ^ 30)
142 to 171 (56 to 67)
120 ^ 90 (47 ^ 35)
171 to 206 (67 to 81)
160 ^ 120 (63 ^ 47)
229 to 275 (90 to 108)
200 ^ 150 (79 ^ 59)
287 to 345 (113 to 136)
240 ^ 180 (94 ^ 71)
345 to 415 (136 to 163)
300 ^ 230 (118 ^ 91) 432 to 519 (170 to 204)
410 ^ 300 (161 ^ 118) 577 to 693 (227 to 273)
610 ^ 460 (240 ^ 181) 867 to 1041 (341 to 410)
5 (1.9)
6 (2.5)
8 (3.1)
10 (3.8)
13 (5.0)
16 (6.3)
19 (7.5)
24 (9.4)
32 (12.5)
48 (18.8)
30"
40"
50"
60"
80"
100"
120"
150"
200"
300"
66 ^ 37 (26 ^ 15)
89 ^ 50 (35 ^ 20)
110 ^ 62 (43 ^ 24)
130 ^ 75 (51 ^ 28)
180 ^ 100 (71 ^ 39)
220 ^ 120 (87 ^ 47)
270 ^ 150 (106 ^ 59)
330 ^ 190 (130 ^ 75)
440 ^ 250 (173 ^ 98)
660 ^ 370 (260 ^ 146)
Units: cm (in.)
Projection Distance U
Minimum Maximum
(Wide) to (Tele)
91 to 110 (36 to 43)
123 to 148 (48 to 58)
154 to 186 (61 to 73)
186 to 224 (73 to 88)
249 to 300 (98 to 118)
312 to 376 (123 to 148)
375 to 452 (148 to 178)
470 to 565 (185 to 223)
628 to 755 (247 to 297)
944 (372)
Offset V
(When image position
is off center)
-1 (-0.4)
-1 (-0.5)
-2 (-0.7)
-2 (-0.8)
-3 (-1.1)
-3 (-1.4)
-4 (-1.6)
-5 (-2.0)
-7 (-2.7)
-10 (-4.1)
Screen
90°
Center of lens
Screen
90°
Center of lens
60
Screen Size and Distance
EMP-S5
See the following table to choose the best position for your projector. The values are only a guide.
Units: cm (in.)
Projection Distance U
Offset V
4:3 Screen Size
16:9 Screen Size
30"
61 ^ 46 (24 ^ 18)
40"
81 ^ 61 (32 ^ 24)
50"
100 ^ 76 (39 ^ 30)
60"
120 ^ 90 (47 ^ 35)
80" 160 ^ 120 (63 ^ 47)
100" 200 ^ 150 (79 ^ 59)
120" 240 ^ 180 (94 ^ 71)
150" 300 ^ 230 (118 ^ 91)
200" 410 ^ 300 (161 ^ 118)
300" 610 ^ 460 (240 ^ 181)
Minimum Maximum
(Wide) to (Tele)
87 to 119 (34 to 47)
117 to 159 (46 to 63)
147 to 200 (58 to 79)
177 to 240 (70 to 95)
237 to 321 (93 to 126)
297 to 402 (117 to 158)
357 to 483 (141 to 190)
447 to 605 (176 to 238)
597 to 807 (235 to 318)
897 (353)
Wide to Tele
4 to -2 (1.7 to -0.9)
6 to -3 (2.3 to -1.1)
7 to -4 (2.8 to -1.4)
9 to -4 (3.4 to -1.7)
11 to -6 (4.5 to -2.3)
14 to -7 (5.7 to -2.9)
17 to -9 (6.8 to -3.4)
22 to -11 (8.5 to -4.3)
29 to -15 (11.3 to -5.7)
43 (17.0)
30"
40"
50"
60"
80"
100"
120"
150"
200"
Projection Distance U
Minimum Maximum
(Wide) to (Tele)
66 ^ 37 (26 ^ 15)
95 to 129 (37 to 51)
89 ^ 50 (35 ^ 20)
128 to 173 (50 to 68)
110 ^ 62 (43 ^ 24)
160 to 218 (63 to 86)
130 ^ 75 (51 ^ 28)
193 to 262 (76 to 103)
180 ^ 100 (71 ^ 39)
258 to 350 (102 to 138)
220 ^ 120 (87 ^ 47)
324 to 438 (127 to 172)
270 ^ 150 (106 ^ 59) 389 to 526 (153 to 207)
330 ^ 190 (130 ^ 75) 487 to 659 (192 to 259)
440 ^ 250 (173 ^ 98) 651 to 879 (256 to 346)
Units: cm (in.)
Offset V
(When image position
is off center)
Wide to Tele
-2 to -9 (-0.6 to -3.4)
-2 to -11 (-0.8 to -4.5)
-3 to -14 (-1.0 to -5.6)
-3 to -17 (-1.2 to -6.8)
-4 to -23 (-1.6 to -9.0)
-5 to -29 (-2.0 to -11.3)
-6 to -34 (-2.4 to -13.5)
-8 to -43 (-3.0 to -16.9)
-10 to -57 (-4.0 to -22.6)
Screen
90°
Center of lens
Screen
90°
Center of lens
Connecting to External Equipment
Connecting to an External Monitor
Computer images being input to the Computer1 input port or the
Computer Input port can be displayed on an external monitor and the
screen at the same time when connected to the projector. This means that
you can check projected images on an external monitor when giving
presentations even if you cannot see the screen.
Connect to an external monitor using the cable supplied with the monitor.
61
Connecting to External Speakers (EMP-83H/822H
Only)
You can connect speakers with built-in amplifiers to the projector's Audio
Out port to enjoy a fuller quality of sound.
Connect with a commercially available audio cable (pin plug W 3.5 mm
stereo mini plug and so on). Use an audio cable compatible with the
connector on the external speakers.
To external speakers
Cable supplied
with monitor
q
Monitor port
To Monitor Out port
• Component video signals and images connected to the
Computer2 port, Video port, and S-Video port cannot be
output to an external monitor.
• The setting gauge for Keystone, the configuration and
help screen, and so on are not output to an external
monitor.
Audio cable
(commercially available)
q
To Audio Out port
When an audio cable plug is inserted in the Audio Out port,
the audio changes to the external destination, and audio is
no longer emitted from the projector's built-in speaker.
Connecting a LAN Cable (EMP-83H/822H Only)
Connect with a commercially available 100baseTX or 10baseT type
LAN cable.
To LAN port
LAN cable
(commercially available)
To LAN port
Attention
To prevent malfunctions, use a category 5 shielded LAN cable.
62
Connecting a USB Cable (EMP-X5/S5 Only)
Connect the USBg port of a computer and the USBport (TypeB) on
the rear of the projector with a commercially available USB cable.
To USB port
USB cable
To USB port
(Type B)
63
Optional Accessories and Consumables
Prepare the following options and consumables. Purchase depending
on usage. The following list of optional accessories is current as of
March, 2007. Details of accessories are subject to change without
notice and availability may vary depending on the country of purchase.
f Optional accessories
Soft carrying case ELPKS16B
Use this case if you need to travel with the projector.
60" portable screen ELPSC07
80" portable screen ELPSC08
100" screen
ELPSC10
Portable roll-type screens (Aspect ratiog 4:3)
50" portable screen ELPSC06
A compact screen that can be carried easily. (Aspect ratio 4:3)
HD-15 cable ELPKC02
(1.8 m - for mini D-Sub15-pin/mini D-Sub 15pin)
This is the same as the computer cable supplied with the projector.
HD-15 cable ELPKC09
(3 m - for mini D-Sub15-pin/mini D-Sub 15pin)
HD-15 PC cable ELPKC10
(20 m - for mini D-Sub15-pin/mini D-Sub 15pin)
Use one of these longer cables if the computer cable bundled with the product is too
short.
Component video cable ELPKC19
(3 m - for mini D-Sub 15-pin/RCA male^3)
Use to connect a component videog source
Ceiling plate* ELPFC03
Pipe 370 (370 mm silver)* ELPFP04
Pipe 570 (570 mm silver)* ELPFP05
Pipe 770 (770 mm silver)* ELPFP06
Ceiling mount (For use with the ceiling plate)* ELPMB18
Use when installing the projector on a ceiling.
* A special method of installation is required to suspend the projector from a
ceiling. Contact your dealer or the nearest address provided in the Support and
Service Guide if you want to use this installation method. sEpson Projector
Contact List
f Consumables
Lamp unit (For EMP-X5/S5) ELPLP41
Lamp unit (For EMP-83H/822H) ELPLP42
Use as a replacement for used lamps.
Air filter (by 2) ELPAF13
Use as a replacement for used air filters.
64
Glossary
65
This section briefly explains terms that are used with the projector and difficult terms that are not explained in the text of this guide. For details,
refer to other commercially available publications.
Aspect ratio
Component Video
Composite video
Contrast
DHCP
Dolby Digital
Gateway address
HDTV
Interlace
IP address
Progressive
Refresh rate
SDTV
SNMP
SNMP Trap IP address
The ratio between an image's length and its height. HDTV images have an aspect ratio of 16:9 and appear elongated. The aspect ratio for
standard images is 4:3.
A video signal which has the luminance component and color component separated to provide better image quality.
Refers to images that consist of three independent signals: Y (luminance signal), Pb and Pr (color difference signals).
Video signals that have the video brightness signals and color signals mixed together. The type of signals commonly used by household
video equipment (NTSC, PAL, and SECAM formats). The carrier signal Y (luminance signal) and chroma (color) signal that are
contained in the color bar are overlapped to form a single signal.
The relative brightness of the light and dark areas of an image can be increased or decreased to make text and graphics stand out more
clearly, or to make them appear softer. Adjusting this particular property of an image is called "contrast adjustment".
An abbreviation of Dynamic Host Configuration Protocol, this protocol automatically assigns an IP addressg to equipment connected to
a network.
A sound format developed by Dolby Laboratories. Normal stereo is a 2-channel format that uses two speakers. Dolby Digital is a 6channel (5.1-channel) system which adds to this a center speaker, two rear speakers, and a sub-woofer.
This is a server (router) for communicating across a network (subnet) divided according to subnet masksg.
An abbreviation for High-Definition Television that refers to high-definition systems which satisfy the following conditions.
• Vertical resolution of 720p or 1080i or greater (p = progressiveg, i = interlaceg)
• Screen aspect ratiog of 16:9
• Dolby Digitalg audio reception and playback (or output)
A method of image scanning whereby the image data is divided into fine horizontal lines that are displayed in sequence starting from left
to right and then from top to bottom. The even-numbered lines and odd-numbered lines are displayed alternately.
A number to identify a computer connected to a network.
A method of image scanning whereby the image data from a single image is scanned sequentially from top to bottom to create a single
image.
The light-emitting element of a display maintains the same luminosity and color for an extremely short time. Because of this, the image
must be scanned many times per second to refresh the light-emitting element. The number of refresh operations per second is called the
Refresh rate and is expressed in hertz (Hz).
An abbreviation for Standard Definition Television that refers to standard television systems which do not satisfy the conditions for
HDTVg High-Definition Television.
An abbreviation for Simple Network Management Protocol, which is the protocol for monitoring and controlling devices such as routers
and computers connected to a TCP/IP network.
This is the IP addressg for the destination computer used for error notification in SNMP
Glossary
Squeeze mode
sRGB
Subnet mask
SVGA
S-Video
SXGA
Synchronization
Tracking
VGA
XGA
66
In this mode, wide-screen images in 16:9 mode are compressed in the horizontal direction so that they are stored on the recording
medium as 4:3 images.
When these images are played back by the projector in squeeze mode, they are restored to their original 16:9 format.
An international standard for color intervals that was formulated so that colors that are reproduced by video equipment can be handled
easily by computer operating systems (OS) and the Internet. If the connected source has an sRGB mode, set both the projector and the
connected signal source to sRGB.
This is a numerical value that defines the number of bits used for the network address on a divided network (subnet) from the IP address.
A type of video signal with a resolution of 800 (horizontal) ^ 600 (vertical) dots that is used by IBM PC/AT-compatible computers.
A video signal which has the luminance component and color component separated to provide better image quality.
Refers to images that consist of two independent signals: Y (luminance signal) and C (color signal).
A type of video signal with a resolution of 1280 (horizontal) ^ 1024 (vertical) dots that is used by IBM PC/AT-compatible computers.
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting
images are not of a good quality. The process of matching the phases of these signals (the relative position of the crests and the troughs in
the signal) is called Synchronization. If the signals are not synchronized, flickering, blurriness, and horizontal interference occur.
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting
images are not of a good quality. The process of matching the frequency of these signals (the number of crests in the signal) is called
Tracking. If tracking is not carried out correctly, wide vertical stripes appear in the signal.
A type of video signal with a resolution of 640 (horizontal) ^ 480 (vertical) dots that is used by IBM PC/AT-compatible computers.
A type of video signal with a resolution of 1024 (horizontal) ^ 768 (vertical) dots that is used by IBM PC/AT-compatible computers.
ESC/VP21 Commands
67
Command List
Cable Layouts
When the power ON command is transmitted to the projector, the power
turns on and it enters warm-up mode. When the projector's power has
turned on, a colon ":" (3Ah) is returned.
When a command is input, the projector executes the command and
returns a ":", and then accepts the next command.
If the command being processed terminates due to a problem, an error
message is output and a ":" is returned.
Item
Power ON/OFF
ON
OFF
Signal selection
Video
S-Video
A/V Mute ON/OFF ON
OFF
A/V Mute selection Black
Blue
Logo
Item
Signal selection
Computer (Auto)
Computer
Component Video
f Serial connection (EMP-83H/822H Only)
• Connector shape
: D-Sub 9-pin (male)
• Projector input connector
: RS-232C
<At the projector>
<At the computer>
Command
PWR ON
PWR OFF
SOURCE 41
SOURCE 42
MUTE ON
MUTE OFF
MSEL 00
MSEL 01
MSEL 02
Command
Computer1
Computer2
Port
Port
SOURCE 1F
SOURCE 2F
SOURCE 11
SOURCE 21
SOURCE 14
SOURCE 24
* Add a Carriage Return (CR) code (0Dh) to the end of each command and
transmit.
At the projector
(PC serial cable)
At the computer
Signal
Function
GND 5
5 GND
GND
RD
2
3 TD
TD
Signal wire
ground
Transmit data
TD
3
2 RD
RD
Receive data
DTR 4
6 DSR
DSR
Data set ready
DSR 6
4 DTR
DTR
Data terminal
ready
68
ESC/VP21 Commands
Connecting a USB (EMP-X5/S5 Only)
USB Connection Setup
Connector shape: USB (Type B)
<At the projector>
<At the computer>
To control the projector using ESC/VP21 commands via a USB
connection, the following preparations must be carried out.
Procedure
the USB driver (USB-COM Driver) from
A Download
the Epson Web site to your computer.
(Type B)
Go to http://www.epson.com and select the support section of your
local Epson Web site.
the downloaded USB driver onto your
B Install
computer.
Read the instructions displayed on the download screen.
"Extended"-"Link 21L" to "On" from the
C Set
projector's configuration menu.
PJLink (EMP-83H/822H Only)
PJLink Class 1 was established by the JBMIA (Japan Business
Machine and Information System Industries Association) as a standard
protocol for controlling network-compatible projector's as part of their
efforts to standardize projector control protocols.
The projector complies with the PJLink Class 1 standard established
by the JBMIA.
It complies with all commands except for the following commands
defined by PJLink Class 1, and agreement was confirmed by the
PJLink standard adaptability verification.
Refer to the JBMIA (Japan Business Machine and Information System
Industries Association) Web site for more details on PJLink.
URL http://pjlink.jbmia.or.jp/english/
f Non-compatible commands
Mute settings
Function
Image muting set
Image muting cancel
Audio muting set
Audio muting cancel
PJLink Command
AVMT 11
AVMT 10
AVMT 21
AVMT 20
f Input names defined by PJLink and corresponding
projector connectors
Input Connector
Computer1 input
Computer2 input
Video input
S-Video input
PJLink Command
INPT 11
INPT 12
INPT 21
INPT 22
69
f Manufacturer name displayed for "Manufacture name
information query"
EPSON
f Model name displayed for "Product name information
query"
EMP-83H
EMP-822H
List of Supported Monitor Displays
f Computer image
Signal
Refresh Rateg
(Hz)
VGAEGA
Resolution
(dots)
Number of
Pixels Used
Display
Aspect is
Resized
(dots)
640 ^ 350
1024 ^ 560
VGAg
60/72/75/85, iMac*1
640 ^ 480
1024 ^ 768
SVGAg
56/60/72/75/85, iMac*1
800 ^ 600
1024 ^ 768
1024 ^ 768
1024 ^ 768
XGAg
*1
60/70/75/85, iMac
SXGAg
70/75/85
1152 ^ 864
1024 ^ 768
SXGA
60/75/85
1280 ^ 960
1024 ^ 768
SXGA
60/75/85
1280 ^ 1024
960 ^ 768
60
1600 ^ 1200
1024 ^ 768
MAC13"
640 ^ 480
1024 ^ 768
MAC16"
832 ^ 624
1024 ^ 768
MAC19"
1024 ^ 768
1024 ^ 768
1024 ^ 768
1024 ^ 768
1152 ^ 870
1016 ^ 768
UXGA
*2
MAC19"
60
MAC21"
SDTVg
(480i)
60
720 ^ 480
1024 ^ 768
SDTV (576i)
50
720 ^ 576
1024 ^ 768
SDTV (480p)
60
720 ^ 480
1024 ^ 768
SDTV (576p)
50
720 ^ 576
1024 ^ 768
HDTVg
(720p)
50/60
1280 ^ 720
1024 ^ 576
HDTV (1080i)
50/60
1920 ^ 1080
1024 ^ 576
70
*1 Connection is not possible if the equipment does not have a VGA output port.
*2 EMP-S5 is not supported.
Even when signals other than those mentioned above are input, it is likely that the
image can be projected.
However, not all functions may be supported.
f Component Video
Signal
SDTVg (480i)
SDTV (576i)
SDTV (480p)
SDTV (576p)
HDTVg
(720p)
16:9
HDTV (1080i)
16:9
Refresh Rateg
(Hz)
60
50
60
50
Resolutions (dots)
Aspect
Aspect Ratio
Ratiog 4:3
16:9
1024 ^ 768
1024 ^ 576
1024 ^ 768
1024 ^ 576
1024 ^ 768
1024 ^ 576
1024 ^ 768
1024 ^ 576
50/60
1024 ^ 768
1024 ^ 576
50/60
1024 ^ 768
1024 ^ 576
f Composite video/S-video
Signal
TV (NTSC)
TV
(PAL,
SECAM)
60
Resolutions (dots)
Aspect
Aspect Ratio
Ratiog 4:3
16:9
1024 ^ 768
1024 ^ 576
50
1024 ^ 768
Refresh Rateg
(Hz)
1024 ^ 576
Specifications
Product name
Dimensions
Panel size
Display method
Resolution
Focus adjustment
Zoom adjustment
Lamp
Max. audio output
Speaker
Power supply
Power
100 to 120 V area
consumption
200 to 240 V area
Operating altitude
Operating temperature
Storage temperature
Mass
71
EMP-83H/822H
EMP-X5
EMP-S5
327 (W) ^ 92 (H) ^ 245 (D) mm
0.63"
0.55"
Polysilicon TFT active matrix
480,000 pixels
786,432 pixels XGA
SVGA (800 (W) ^
(1024 (W) ^ 768 (H) dots) ^ 3
600 (H) dots) ^ 3
Manual
Digital
Manual (1 to 1.2)
(1 to 1.35)
UHE lamp, 170 W
Model No.:
Model No.: ELPLP41
ELPLP42
10 W monaural
1 W monaural
1
100 to 240 V AC ±10%, 50/60 Hz 2.8 to 1.2 A
Operating: 248 W
Standby power consumption (network invalid): 4.1 W
Standby power consumption (network valid): 5.0 W
Operating: 231 W
Standby power consumption (network invalid): 5.8 W
Standby power consumption (network valid): 7.0 W
Altitude 0 to 2286 m (0 to 7500 ft)
5 to 35°C (No condensation)
-10 to +60°C (No condensation)
Approx 2.9 kg
Approx 2.7 kg
Approx 2.6 kg
Pixelworks DNXTM ICs
are used in this projector.
Angle of tilt
0 to 30°
0 to 30°
If you use the projector tilted at an angle of
more than 30 it could be damaged and cause
an accident.
72
Specifications
Connectors
Computer1 input port
1
Audio1 input port
Computer2 input port
1
1
Audio2 input port
Computer input port
Audio-L/R input port
S-Video input port
Video input port
Audio-L/R input port
Monitor Out port
Audio Out port
RS-232C port
1
1
1
1
1
1
1
1
1
LAN port
USB port (Type B)*
1
1
Mini D-Sub15-pin
(female) blue
Stereo mini jack
Mini D-Sub15-pin
(female) blue
Stereo mini jack
-
-
Mini D-Sub15-pin (female) blue
RCA pin jack
Mini DIN 4-pin
RCA pin jack
RCA pin jack
Mini D-Sub15-pin (female) black
Stereo mini jack
Mini D-Sub 9-pin
(male)
RJ45
USB connector (Type B)
* This supports USB2.0.
USB ports are not guaranteed to operate all devices that support USB.
Other detailed specifications, please access your location (country/area) from Epson homepage, http://www.epson.com
Specifications
Safety standards
USA: UL60950-1
Canada: CSA C22.2 No.60950-1
EU: The Low Voltage Directive
(73/23/EEC)
IEC/EN60950-1
This product is also designed for IT power distribution system with
phase-to-phase voltage 230V.
EMC standards
USA: FCC Part 15B Class B (DoC)
Canada: ICES-003 Class B
EU: The EMC Directive
(89/336/EEC)
EN55022, Class B
EN55024
IEC/EN61000-3-2
IEC/EN61000-3-3
Australia/New Zealand: AS/NZS CISPR 22:2002 Class B
73
74
Specifications
DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B
Personal Computers
We:
Located at:
Tel:
Epson America, Inc.
3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
562-290-5254
Declare under sole responsibility that the product identified herein,
complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital
device. Each product marketed, is identical to the representative unit
tested and found to be compliant with the standards. Records maintained
continue to reflect the equipment being produced can be expected to be
within the variation accepted, due to quantity production and testing on a
statistical basis as required by 47CFR 2.909. Operation is subject to the
following two conditions : (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Trade Name:
EPSON
Type of Product:
Projector
Model:
EMP-83H/822H/X5/S5
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause interference to radio and television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this
equipment will invalidate the FCC Certification or Declaration of this device
and may cause interference levels which exceed the limits established by the
FCC for this equipment. It is the responsibility of the user to obtain and use a
shielded equipment interface cable with this device. If this equipment has
more than one interface connector, do not leave cables connected to unused
interfaces. Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
Appearance
75
The external dimensions for EMP-83H/822H/X5/S5 are the same.
3-M4Þ9
Center of lens
103.8
94.9
12
56.2*
245.0
92.0
8.3
13.3
83.5
327.0
115.0
127.0
69.5
* Distance from center of lens to suspension bracket fixing point
Units: mm
Index
A
76
D
A/V Mute ............................................................. 15
A/V mute slide ....................................................... 5
Abs. Color Temp. ................................................ 25
Air exhaust vent .................................................... 5
Air filter ................................................................ 11
Air filter replacement period ................................ 56
Air intake vent ..................................................... 11
Angle of tilt .......................................................... 71
Aspect ratio ......................................................... 16
Audio Out port ....................................................... 6
Audio-L/R input port .......................................... 6, 7
Auto Setup .................................................... 26, 27
DHCP ..................................................................31
Direct Power On ..................................................30
Display .................................................................29
Display Background .............................................29
Keystone ............................................................. 28
Email Address 1/2/3 setting .................................32
ESC/VP21 ...........................................................67
Extended menu ...................................................29
External dimension diagram ................................75
External monitor ..................................................61
External speakers ................................................61
E-zoom ................................................................17
L
Focus ring ..............................................................5
Freeze .................................................................16
Front ....................................................................29
Front adjustable feet ..............................................5
Full lock ...............................................................20
M
Lamp cover ........................................................... 5
Lamp Hours ........................................................ 34
Lamp indicator .................................................... 38
Lamp replacement period ................................... 52
LAN port ................................................................ 6
Language ............................................................ 30
Low brightness .................................................... 28
F
C
Ceiling ................................................................. 29
Cleaning the air filter and air intake vent ............. 50
Cleaning the projector's surface .......................... 50
Color Adjustment ........................................... 24, 25
Color Mode .............................................. 14, 24, 25
Color Saturation ............................................ 24, 25
Computer Input ................................................... 27
Computer input port .............................................. 7
Computer1 Input ................................................. 26
Computer1 Port ..................................................... 6
Computer2 Input ................................................. 26
Computer2 input port ............................................ 6
Configuration menu ............................................. 23
Connecting a LAN Cable ..................................... 62
Connecting a USB Cable .................................... 63
Consumables ...................................................... 64
Contrast ......................................................... 24, 25
Control panel ......................................................... 8
Cross ................................................................... 17
K
E
B
Blackboard .......................................................... 14
Brightness ..................................................... 24, 25
Brightness Control ............................................... 28
Indicators ............................................................ 38
Info menu ............................................................ 34
Input Signal ......................................................... 34
IP address ........................................................... 31
MAC Address ...................................................... 31
Mail ..................................................................... 32
Mail Notification ................................................... 32
Menu ................................................................... 23
Messages ............................................................ 29
Monitor Out port ................................................ 6, 7
G
Game ...................................................................14
Gateway address .................................................31
Glossary ..............................................................65
N
Network Menu ..................................................... 31
Network Protect .................................................. 19
Numeric buttons .................................................. 10
H
HDTV ...................................................................70
Help function ........................................................37
High Altitude Mode: .............................................30
How to replace the air filter ..................................56
How to replace the lamp ......................................53
I
Image menu ...................................................24, 25
O
Operating temperature ........................................ 71
Operation ............................................................ 30
Operation Lock .............................................. 20, 28
Optional accessories ........................................... 64
Overheating ........................................................ 39
77
Index
P
Sharpness .....................................................24, 25
Signal menu .........................................................25
Sleep Mode .........................................................30
SMTP Server .......................................................32
SNMP ..................................................................32
Software keyboard ...............................................32
Source .................................................................34
Source Search .................................................8, 10
Speaker ...............................................................61
Specifications ......................................................71
Sports ..................................................................14
sRGB ...................................................................14
Standby Mode .....................................................30
Startup Screen .....................................................29
Storage temperature ............................................71
Sub Menu ............................................................23
Subnet mask ........................................................31
Supported monitor displays .................................70
Suspension bracket fixing points ...................11, 75
S-video port .......................................................6, 7
Sync Info ..............................................................34
Synchronization .............................................26, 27
Part names and functions ..................................... 5
Password protect ................................................ 18
Password protect sticker ..................................... 19
Photo ................................................................... 14
PJLink ................................................................. 69
PJLink Password ................................................. 31
Port Number ........................................................ 32
Position ......................................................... 26, 27
Power indicator ................................................... 38
Power inlet ........................................................ 6, 7
Power on protect ................................................. 18
Presentation ........................................................ 14
Problem solving ................................................... 38
Progressive ................................................... 26, 27
Projection ............................................................ 29
Projection distance .............................................. 59
Projector Name ................................................... 32
R
Rear .................................................................... 29
Rear foot ............................................................. 11
Rear screen ......................................................... 49
Refresh Rate ....................................................... 34
Remote control .................................................... 10
Remote control light-emitting area ...................... 11
Remote receiver ............................................ 5, 6, 7
Replacing batteries ............................................. 51
Request code ...................................................... 20
Reset All .............................................................. 35
Reset menu ......................................................... 35
Resetting the lamp operating time ................ 35, 55
Resolution ..................................................... 34, 70
RS-232C port ........................................................ 6
S
W
Warning mail ....................................................... 33
Web Control Password ....................................... 31
Wide-screen projection ....................................... 16
Wired LAN ........................................................... 31
Z
Zoom ring .............................................................. 5
T
Temp indicator .....................................................38
Theater ................................................................14
Tint .................................................................24, 25
Top menu ............................................................23
Tracking .........................................................26, 27
Trap IP Address ...................................................32
U
USB port ................................................................7
User's Logo* ........................................................57
User’s Logo Protect* ............................................18
V
Screen size ......................................................... 59
Settings menu ..................................................... 28
Video Signal ............................................ 26, 27, 34
Volume ................................................................ 28
Video port ..........................................................6, 7
*Depending on the area of purchase, the User's
Logo function may not be available for EMPX5/S5. In that case, "User's Logo Protect" is
not displayed.
78
All rights reserved. No part of this publication may be reproduced, stored
in a retrieval system, or transmitted in any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise, without the
prior written permission of Seiko Epson Corporation. No patent liability is
assumed with respect to the use of the information contained herein.
Neither is any liability assumed for damages resulting from the use of the
information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the
purchaser of this product or third parties for damages, losses, costs, or
expenses incurred by the purchaser or third parties as a result of: accident,
misuse, or abuse of this product or unauthorized modifications, repairs, or
alterations to this product, or (excluding the U.S.) failure to strictly
comply with Seiko Epson Corporation's operating and maintenance
instructions.
Seiko Epson Corporation shall not be liable against any damages or
problems arising from the use of any options or any consumable products
other than those designated as Original Epson Products or Epson
Approved Products by Seiko Epson Corporation.
General Notice:
Macintosh, Mac, and iMac are registered trademarks of Apple Computer,
Inc.
IBM is a registered trademark of International Business Machines
Corporation.
Windows, Windows NT, and PowerPoint are either registered trademarks
or trademarks of Microsoft Corporation in the U.S and/or other countries.
Dolby is a trademark of Dolby Laboratories.
Pixelworks and DNX are trademarks of Pixelworks, Inc.
PJLink trademark is a trademark applied for registration or is already
registered in Japan, the United States of America and other countries and
areas.
Other product names used herein are also for identification purposes only
and may be trademarks of their respective owners. Epson disclaims any
and all rights in those marks.
This product uses open source software.
The contents of this guide may be changed or updated without further
notice.
Illustrations in this guide and the actual projector may differ.
ZSEIKO EPSON CORPORATION 2007. All rights reserved.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • Home cinema
  • LCD 2200 ANSI lumens
  • Lamp 4000 h
  • XGA (1024x768) 400:1
  • Screen size compatibility: 762 - 7620 mm (30 - 300") Number of colours: 16.78 million colours
  • 10 W

Related manuals

Download PDF

advertisement