VC-A410U
VC-A410U
VC-H810U
VC-H810U
SERVICE MANUAL
S20W6VC-A410U
SERVICE MANUAL
VIDEO CASSETTE RECORDER
VC-A410U
MODELS VC-H810U
VIDEO CASSETTE RECORDER
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its
original condition and only parts identical to those specified
be used.
CONTENTS
MODELS VC-A410U/H810U
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Page
GENERAL INFORMATION ............................................................................................................ 5
DISASSEMBLY AND REASSEMBLY ............................................................................................ 7
FUNCTION OF MAJOR MECHANICAL PARTS ......................................................................... 10
ADJUSTMENT, REPLACEMENT AND ASSEMBLY OF MECHANICAL UNITS ........................ 12
ELECTRICAL ADJUSTMENT ...................................................................................................... 31
MECHANISM OPERATION FLOWCHART AND TROUBLESHOOTING GUIDE ...................... 33
TROUBLESHOOTING ................................................................................................................. 39
BLOCK DIAGRAM ....................................................................................................................... 50
SCHEMATIC DIAGRAM AND PWB FOIL PATTERN .................................................................. 58
REPLACEMENT PARTS LIST .................................................................................................... 73
EXPLODED VIEW OF MECHANICAL PARTS ............................................................................ 81
PACKING OF THE SET .............................................................................................................. 85
VC-A410U/H810U
VC-A410U/H810U
SHARP CORPORATION
.............. Models for Canada
.............. Models for U.S.A.
This document has been published to be used for
after sales service only.
1The contents are subject to change without notice.
VC-A410U
VC-H810U
IMPORTANT SERVICE NOTES
etc.) and measure the AC voltage drop across the
resistor. Reverse the AC plug on the set and repeat
AC voltage measurements for each exposed part.
Any reading of 0.45V rms (this corresponds to 0.3mA
rms AC.) or more is excessive and indicates a potential shock hazard which must be corrected before
returning the video cassette recorder to the owner.
BEFORE RETURNING THE VIDEO CASSETTE
RECORDER
Before returning the video cassette recorder to the user,
perform the following safety checks.
1. Inspect all lead dress to make certain that leads are
not pinched or that hardware is not lodged between
the chassis and other metal parts in the video cassette
recorder.
2. Inspect all protective devices such as non-metallic
control knobs, insulation materials, cabinet backs,
adjustment and compartment covers or shields, isolation resistor/capacitor networks, mechanical insulators etc.
3. To be sure that no shock hazard exists, check for
current in the following manner.
● Plug the AC line cord directly into a 120 volt AC outlet
(Do not use an isolation transformer for this test).
● Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series with
all exposed metal cabinet parts and a known earth
ground, such as a water pipe or conduit.
● Use an SSVM or VOM with 1000 ohm per volt, or
higher, sensitivity or measure the AC voltage drop
across the resistor (See Diagram).
● Move the resistor connection to earth exposed metal
part having a return path to the chassis (antenna,
metal cabinet, screw heads, knobs and control shafts,
SSVM
AC SCALE
1.5k ohms.
10W
0.15 µF
TEST PROBE
TO EXPOSED
METAL PARTS
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO
NOT REMOVE COVER. NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol warns the user of uninsulated voltage
within the unit that can cause dangerous electric shocks.
This symbol alerts the user that there are important
operating and maintenance instructions in the literature
accompanying this unit.
CAUTION:
3.0A 125V
This symbol mark means fast operating fuse.
For continued protection against risk of fire, replace
only with same type fuse F901 (3.0A, 125V).
2
CONNECT TO
KNOWN EARTH
GROUND
VC-A410U
VC-H810U
NOTES DE SERVICE IMPORTANTES
pièces métalliques exposées ayant un parcours de
retour au châssis (connexions d’antenne, coffret
métallique, tétes de vis, boutons et arbres de
commande, etc.) et mesurer la chute de tension CA
entre la résistance. Inverser la fiche CA (une fiche
intermédiaire non polarisée doit être utilisée à seule fin
de faire ces vérifications.) sur l’appareil et répéter les
mesures de tension CA pour chaque piéce métallique
exposée. Toute lecture de 0,45 Vrms (ceci correspond
à 0,3 mArms CA) ou plus est excessive et signale un
danger de choc qui doit être corrigé avant de rendre le
magnétoscope à son utilisateur.
AVANT DE RENDRE LE MAGNETOSCOPE
Avant de rendre le magnétoscope à l’utilisateur, effectuer
les vérifications de sécurité suivantes.
1. Vérifier toutes les gaines de fil pour être sûr que les fils
ne sont pas pincés ou que le matériel n’est pas coincé
entre le châssis et les autres pièces métalliques dans
le magnétoscope.
2. Vérifier tous les dispositifs de protection tels que les
boutons de commande non métalliques, les matériaux
d’isolement, le dos du coffret, les couvercles de
compartiment et ajustement ou les boucliers, les
réseaux de résistance / condensateur d’isolement, Ies
isolateurs mécaniques, etc.
3. Pour être sûr qu’il n’y a aucun risque de choc électrique,
vérifier le courant de fuite de la maniére suivante.
● Brancher le cordon d’alimentation secteur directement
dans une prise de courant de 120 volts. (Ne pas utiliser
de transformateur d’isolement pour cet essai).
● Utiliser deux fils à pinces et connecter une résistance
de 10 watts 1,5 kohm en parallèle avec un condensateur
de 0,15 µF en série avec des pièces du coffret
métallique exposées et une masse de terre connue
telle qu’un tuyau ou un conduit d’eau.
● Utiliser un VTVM ou VOM avec une sensibilité de 1000
ohms par volt ou plus ou mesurer la chute de tension
CA entre la résistance (voir diagramme).
● Déposer la connexion de la résistance à toutes les VERS PIECES
VTVM
ECHELLE CA
1,5 KOHMS
10W
0,15 µF
SONDE D'ESSAI
METALLIQUES
EXPOSEES
ATTENTION: POUR REDUIRE LES RESQUES D'INCENDIE OU DE CHOC ELECTRIQUE,
NE PAS EXPOSER CET APPAREIL A
LA PLUIE OU A L'HUMIDITE.
ATTENTION
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
ATTENTION: AFIN DE REDUIRE LES RISQUES DE CHOC
ELECTRIQUE, NE PAS RETIRER LE COUVERCLE,
AUCUN ORGANE INTERNE NE PEUT ETRE
REPARE PAR L'UTILISATEUR. CONFIER
L'APPAREIL A UN DEPANNEUR QUALIFIE.
Ce symbole signale à l'utilisateur la présence d'une
tension non isolée à l'intérieur de l'appareil qui peut être
la cause de secousses électriques dangereuses.
Ce symbole avertit l'utilisateur que des instructions
importantes relatives à l'utilisation et àl'entretien se
trouvent dans le manuel accompagnant l'appareil.
PRECAUTION:
Cette marque indique le fusible à action in stantansée.
Pour la protection continue contre le risque d'incendie,
ne remplacer que par le fusible type F901 (3,0A, 125V).
3,0A 125V
3
CANNECTER A
UNE MASSE DE
TERRE CONNUE
VC-A410U
VC-H810U
PRECAUTIONS IN PART REPLACEMENT
When servicing the unit with power on, be careful to the section marked white all over.
This is the primary power circuit which is live.
When checking the soldering side in the tape travel mode, make sure first that the tape has been loaded and then turn
over the PWB with due care to the primary power circuit.
Make readjustment, if needed after replacement of part, with the mechanism and its PWB in position in the main frame.
(1) Start and end sensors: Q701 and Q702
Insert the sensor’s projection deep into the upper hole of the holder. Referring to the PWB, fix the sensors tight
enough.
(2) Photocoupler: IC901
Refer to the symbol on the PWB and the anode marking of the part.
(3) Cam switches A and B: D708 and D709.
Adjust the notch of the part to the white marker of the symbol on the PWB. Do not allow any looseness.
(4) Take-up and supply sensors: D707 and D706.
Be careful not to confuse the setting direction of the parts in reference to the symbols on the PWB. Do not allow any
looseness.
4
VC-A410U
VC-H810U
1. GENERAL INFORMATION
1-1 FEATURES
Only for VC-H810U
•
Hi-Fi Stereo Sound
• Built-in MTS (Multi-channel TV Sound) Decoder
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Common Features
• EZ Set Up
• S-VHS Quasi Playback
• Double-Azimuth 4-Heads
• 19µ Clear Picture System (in EP mode)
• HQ System for Better Resolution and Color Reproduction
• Multi-Language (English/Spanish/French) OSD (On Screen
Display) with Menu Screen Guidance
• 181-channel PLL Quartz Synthesized Random Access Tuner
with Automatic Channel Setting
• Quick Start with Full Loading Mechanism
• 1-Year, 8 Event Programmable Timer
• Simple Recording Timer
Unified Remote Control
Sharp Super Picture
1minute Timer Backup
Field-Still/Variable Slow/Frame Advance
Real-Time Counter (On Screen Display)
Automatic Daylight Saving-Time (D.S.T.) Adjustment
Blue Screen Noise Elimination
Auto Tracking Control System
Digital Program Search System (DPSS)
Skip Search
Instant Replay
Auto Zero Back
Recorded Section Auto Repeat
Full Automatic Playback
Tamper Proof
Up to 8 Hours of Recording and Playback (with T-160
cassette)
1-2 SPECIFICATIONS
Format:
Video Recording System:
Number of Video Heads:
Video Signal Standard:
Audio Recording System:
Tape Width:
Tape Speed:
Maximum Recording Time:
Channel Coverage:
Antenna Input:
Video Input:
Video Output:
Audio Input:
Audio Output:
Hi-Fi Audio (Only for Hi-Fi model):
Dynamic Range:
Frequency Response:
Memory Backup:
Operating Temperature:
Storage temperature:
Power Source:
Power Consumption:
Weight:
Dimensions (approx.):
Accessories included:
VHS NTSC Standard
Rotary, Slant Azimuth Two-Head Helical Scan System
4
NTSC Color System
1 Stationary Head for Linear Audio
2 Rotary Heads for Hi-Fi stereo (Only Hi-Fi model)
12.7 mm (1/2 inch)
(SP) 33.35 mm/sec. (1.31 i.p.s.)
(LP) 16.67 mm/sec. (0.66 i.p.s.) (playback only)
(EP) 11.12 mm/sec. (0.44 i.p.s.)
(SP) 160 min. (T-160)
(EP) 480 min. (T-160)
VHF 2-13
UHF 14-69
CATV 1-125
75 Ohm
0.5 to 2.0 Vp-p, 75 Ohm unbalanced
1.0 Vp-p, 75 Ohm unbalanced
–8 dBs, 47 kOhm unbalanced (0 dBs = 0.775 Vrms)
–8 dBs, 1 kOhm unbalanced (0 dBs = 0.775 Vrms)
90 dB
20 Hz-20 kHz
1 min.
5°C to 40°C (41°F to 104°F)
–20°C to 60°C (–4°F to 140°F)
120 V AC, 60 Hz
18 W
2.8 kg (6.2 lbs)
360 (W) x 92.5 (H) x 255 (D) mm (14-3/16" x 3-41/64" x 10-3/64")
75 ohm coaxial cable, Operation manual, Infrared remote control, Battery (2 pcs.)
Note: Specifications are subject to change without notice.
5
6
3
2
1
Basic function controls
(see Playback/Recording)
2
1
Point Remote Control at this window.
Remote Sensor
6
VCR LED indicator
This indicator lights up when selecting "VCR" by using
the TV/VCR button.
This indicator lights up when the set mode is locked.
) LED indicator
TAMPER PROOF (
REC LED indicator
6
REMOTE SENSOR
This indicator lights up when the VCR is set for timer
recording, Simple Recording Timer and Recording with
the Timer.
5
4
5
TAMPER
PROOF
TIMER LED indicator
4
REC
This indicator lights up on during recording. This indicator
flashes during REC-Pause.
3
VCR
This indicator lights up whenever the VCR is turned on.
POWER LED indicator
TIMER
POWER
LED Indicator (explained throughout the operation Instruction)
POWER button
(When pressed to turn on the VCR, POWER LED indicator
will light up. When the power is turned off. POWER LED
indicator wil turn off.)
Cassette compartment (see Playback/Recording)
VC-A410U
VC-H810U
1-3 LOCATION OF MAJOR COMPONENTS AND CONTROL
VC-A410U
VC-H810U
2. DISASSEMBLY AND REASSEMBLY
TOP CABINET
2-1 DISASSEMBLY OF MAJOR BLOCKS
TOP CABINET
FRONT PANEL
1
: Remove 2 screws 1.
: Remove button 2.
Remove 2 screws 3 and 7 clips 4.
: Remove 1 screw 5.
OPERATION
PWB
SHIELD ANGLE : Remove 1 screw 6 with shield angle.
MECHANISM/
: Remove 1 screw 7, 1 screw 8, 2
MAIN PWB
screws 9, 2 screws 0. Remove 1
screw q with antenna terminal cover.
Remove 1 screw w with top cabinet
fix angle.
ANTENNA
TERMINAL
COVER
VC-H810U
SHIELD
ANGLE
3
C
10
3
ANTENNA
TERMINAL
COVER
VC-A410U
A
9
B
11
11
MECHANISM/
MAIN PWB
ASSEMBLY
H/A SHIELD
(Bottom)
A
LED PWB
LED HOLDER
7
TOP CABINET
FIX ANGLE
12
C
B
OPERATION PWB
MAIN FRAME
5
8
FRONT PANEL
4
2
7
6
VC-A410U
VC-H810U
2-2 DISASSEMBLING THE MECHANISM/MAIN PWB ASSEMBLY
2. Removing the mechanism and cassette housing.
Remove 2 screws 4 fixing the cassette housing to the
mechanism, and remove the cassette housing.
1. When removing the mechanism from the main PWB,
remove the antenna cover 1 screw 1, and remove the
antenna terminal cover.
Remove the PWB bottom plate 1 screw 2.
Remove the FFC cable (AA, AD, AH) 3 which connecting the PWB and the mechanism.
Take out vertically the mechanism so that it does not
damage the adjacent parts.
4
MECHANISM CHASSIS
CASSETTE
HOUSING
1
3
MAIN PWB
2
8
VC-A410U
VC-H810U
2-3 CARES WHEN REASSEMBLING
cassette housing. (Conditions: When mechanism and PWB
have been installed)
INSTALLING THE CASSETTE HOUSING
When the cassette housing is installed on the mechanism,
the initial setting is essential condition.
There are two initial setting methods, namely electrical and
mechanical.
1. Electrical initial setting
So as to perform initial setting of mechanism execute the
Step 1 of Installation of cassette housing. After ascertaining
the return to the initial setting position (*1) install the
2. Mechanical initial setting
Feed the pulley feed gear of loading motor with screw
driver. After ascertaining the return to the initial set position
(*1) install the cassette housing in the specified position.
(This method is applied only for the mechanism.)
Pulley feed gear
Casecon
drive gear
Screwdriver
Drive angle of
cassette housing
Tilt mark (*1)
INSTALLING THE MECHANISM ON PWB
Lower vertically the mechanism, paying attention to the
mechanism edge, and install the mechanism with due care
so that the parts are not damaged. So as to fix the mechanism to the main PWB install two housings. (Fit the antenna
cover to one of them. For other, fix the vicinity of loading
motor and solder joint side of main PWB.) Connect again
the FFC cable (AA-MH, AD-ME, AH-MH) between the
mechanism and the main PWB.
PARTS WHICH NEED PARTICULAR CARE
When installing the mechanism chassis on the PWB unit,
take care so as to prevent deformation due to contact of
mechanism chassis with REC TIP SW.
AE CONNECTOR
END SENSOR
REC TIP SW
AC CONNECTOR
START SENSOR
AL CONNECTOR
9
VC-A410U
VC-H810U
3. FUNCTION OF MAJOR MECHANICAL PARTS (TOP VIEW)
15
17
10
18
14
1
9
2
11
7
5
3
12
8
6
No.
16
13
4
Function
No.
Function
1
Full erase head
8
Take-up main brake
2
Supply pole base ass’y
9
Pinch drive cam
3
Tension arm
10
A/C head ass’y
4
Idler wheel ass’y
11
Reverse guide lever ass’y
5
Pinch drive lever ass’y
12
Casecon drive gear
6
Supply reel disk
13
Take-up reel disk
7
Supply main brake
14
Pinch roller lever ass’y
10
VC-A410U
VC-H810U
FUNCTION OF MAJOR MECHANICAL PARTS (BOTTOM VIEW)
21
22
19
26
20
12
23
No.
24
Function
No.
Function
15
Drum ass’y
22
Reel belt
16
Loading motor
23
Clutch lever
17
Drum drive motor
24
Limiter pulley ass’y
18
Take-up pole base ass’y
26
Shifter
19
Slow brake lever
20
Master cam
21
Capstan D.D. motor
11
VC-A410U
VC-H810U
4. ADJUSTMENT, REPLACEMENT AND ASSEMBLY OF MECHANICAL UNITS
The explanation given below relates to the on-site general service (field service) but it does not relates to the adjustment
and replacement which need high-grade equipment, jigs and skill. For example, the drum assembling, replacement and
adjustment service must be performed by the person who have finished the technical courses.
4-1 MECHANISM CONFIRMATION ADJUSTMENT JIG
So as to perform completely the mechanism adjustment prepare the following special jigs. So as to maintain the initial
performance of the machine the maintenance and check are necessary. Utmost care must be taken so that the tape is
not damaged. If adjustment needs any jig, be sure to use the required jig.
No.
Jig ltem
Part No.
Code
1.
Torque Cassette Meter
JiGVHT-063
CZ
JiGTG0090
CM
2.
Torque Gauge
JiGTG1200
CN
3.
Torque Gauge Head
JiGTH0006
AW
4.
Torque Driver
JiGTD1200
CB
Master Plane Jig and
Reel Disk Height
Adjusting Jig
JiGRH0002
BR
5.
JiGMP0001
BY
JiGSG2000
BS
JiGSG0300
BF
6.
Configuration
Remarks
This cassette torque meter is used for checking and adjusting the torque of take-up for
measuring tape back tension.
These Jigs are used for checking
and adjusting the torque of take-up
and supply reel disks.
When fixing any part to the threaded
hole using resin with screw, use the
jig. (Specified torque 5 kg)
These Jigs are used for checking
and adjusting the reel disk height.
There are two gauges used for the
tension measurements, 300 g and
2.0 kg.
Tension Gauge
7.
Pinch pressing force
measuring jig
JiGADP003
BK
This Jig is used with the tension
gauge. Rotary transformer clearance
adjusting jig.
8.
Reverse guide height
adjustment box driver
JiGDRiVER11055
AR
This Jig is used for height adjustment of the
reverse guide (for reverse guide height adjustment).
These tapes are especially used for
electrical fine adjustment.
Video
9.
Alignment Tape
Guide roller height
10. adjustment driver
X value adjustment
11.
gear driver
12.
Reverse Guide Height
Adjusting Jig
VROATSV
CD
VROEFZCS
OR
VROEFZHS
BG
HiFi Audio
Track
525 Monoscope
7k
—
58µm
NTSC Color Bar
1k
—
58µm
—
19µm
Black Level
(only SYNC) signal
BH
Audio
1k
2.3k
This screwdriver is used for adjusting the
guide roller height.
JiGDRiVERH-4 AP
JiGDRiVER-6
BM
For X value adjustment
JiGRVGH-F18
BU
This Jig is used for height
adjustment of the reverse guide.
12
VC-A410U
VC-H810U
4-2 MAINTENANCE CHECK ITEMS AND EXECUTION TIME
Perform the maintenance with the regular intervals as follows so as to maintain the quality of machine.
Maintained 500 1000 1500 2000 Possible symptom
Remarks
encountered
hrs. hrs. hrs. hrs.
Parts
Abnormal rotation or significant
Guide roller ass’y
vibration requires replacement.
Sup guide shaft
Reverse guide
Lateral noises Head
occasionally blocked
Clean tape contact part with the
specified cleaning liquid.
Slant pole on pole base
Full erase head
A/C head
Upper and lower drum ass’y
Capstan D.D. motor
Pinch roller
Reel belt
Colour and beating
Small sound or sound
distortion
Poor S/N ratio, no colour
Poor flatness of the
envelope with alignment
tape
No tape running,
uneven colour
No tape running, tape
slack
No tape running, tape
slack, no fast forward/
rewind motion
Tension band ass’y
Screen swaying
Loading motor
Cassette not loaded or
unloaded
Idler ass’y
Limiter pulley
Supply/take-up main brake levers
Clean tape contact area with the
specified cleaning liquid.
Clean rubber and rubber contact
area with the specified cleaning
liquid.
No tape running, tape
slack
Tape slack
NOTE
: Part replacement.
: Cleaning
: Apply grease
<Specified> Cleaning liquid Industrial ethyl alcohol
* This mechanism does not need electric adjustment with variable resistor. Check parts. If any deviation is found,
clean or replace parts.
Video head cleaning procedure
1. Apply one drop of cleaning liquid to the cleaning paper with the baby oiler.
2. Gently press the cleaning paper against the video head to fix your finger, and move the upper drum so that each head
is passed to and fro 5 times (do not move the cleaning paper).
3. Wipe with the dry cleaning paper.
Rotate the upper drum
with one hand.
Notes :
• Use the commercially available ethanol of Class 1 as
cleaning liquid.
• Since the video head may be damaged, do not move up
and down the cleaning paper.
• Whenever the video head is cleaned, replace the cleaning paper.
• Do not apply this procedure for the parts other than the
video head.
Gently press the cleaning paper to
fix with your finger, and rotate the
upper drum to clean.
Move to and fro 5 times for each head.
(Do not move the cleaning paper.)
Parts Code
ZPAPRA56-001E
ZOiLR-02-24TE
13
Description
Cleaning Paper
Babe Oiler (Spoit)
Code
AW
AH
VC-A410U
VC-H810U
4-3 REMOVING AND INSTALLING THE CASSETTE HOUSING
Notes:
1. When fitting the S/E sensor holder to the cassette
controller frame L/R, take care.
2. Misengagement of teeth of casecon drive gear and drive
angle gear causes malfunction. (The cassette cannot be
set, load and ejection are repeated).
3. In the case when you use the magnet screw driver, never
approach the magnet driver to the A/C head, FE head,
and drum.
4. When installing or removing, take care so that the
cassette housing control and tool do not contact the
guide pin or drum.
5. After installing the cassette housing control once perform cassette loading operation.
• Removal
1. In the cassette removing mode, remove the cassette.
2. Unplug the power cord.
3. Remove in the following numerical order.
a) Remove two screws 1.
b) Slide and pull up the cassette housing control.
1
4-4 TO RUN A TAPE WITHOUT THE CASSETTE
HOUSING CONTROL ASSEMBLY
1.
2.
3.
4.
Remove the full-surface panel.
Short-circuit between TP803 and TP802.
Plug in the power cord.
Turn off the power switch.
(The pole bases move into U.L.position.)
5. Open the lid of a cassette tape by hand.
6. Hold the lid with two pieces of vinyl tape.
7. Set the cassette tape in the mechanism chassis.
8. Stabilize the cassette tape with a weight (500g) to
prevent floating.
9. Turn on the power switch.
10. Perform running test.
Figure 4-1.
• Reassembly
1. Before installing the cassette housing control, shortcircuit between TP803 and TP802 provided at operation
PWB, press the eject button. The casecon drive gear
turns and stops when the positioning mark appears.
Engage two teeth of casecon drive gear with the three
teeth of casecon drive angle gear, and set on the
mechanism chassis as shown below.
500g
Weight to prevent
float (500g)
Mechanism chassis
Figure 4-3.
Note:
The weight should not be more than 500g.
Casecon
drive gear
Casecon drive
angle gear
To take out the cassette tape.
1. Turn off the power switch.
2. Take out the cassette tape.
Figure 4-2.
2. Install in the reverse order of removal.
14
VC-A410U
VC-H810U
4-5 REEL DISK REPLACEMENT AND HEIGHT
CHECK
4. Assemble the Supply main brake ass'y.
Notes:
1. When installing the reel disk, take due care so that the
tension band ass'y is not deformed and grease does no
adhere.
2. Do not damage the Supply main brake ass'y. Be careful
so that grease does not adhere to the brake surface.
•
1.
2.
3.
4.
Removal
Remove the cassette housing control assembly.
Pull the tension band out of the tension arm ass'y.
Remove the Supply/Take-up main brake ass'y.
Open the hook at the top of the reel disk, and remove the
reel disk.
Note:
Take care so that the tension band ass'y and main brake
ass'y (especially soft brake) are not deformed.
• Reassembly (Take-up reel disk)
1. Clean the reel disk shaft and apply grease (SC-141) to
it.
2. Align the phase of the reel disk to that of the reel relay
gear and to install a new take-up reel disk onto the shaft.
3. Check the reel disk height and reassemble the take-up
main brake ass'y.
Note:
1. Take care so that the Take-up main brake ass'y is not
damaged. Take care so that grease does not adhere the
brake surface.
2. After reassembly, check the video search rewind back
tension (see 4-10), and check the brake torque (see 414).
Tension arm ass'y
Take-up main brake ass'y
Supply main brake ass'y
Tension band ass'y
• Height checking and adjustment
Note:
1. Set the master plane with due care so that it does not
contact the drum.
2. When putting the master plane, shift the reverse guide
a little in the loading direction. Care must be taken since
excessive shift results in damage.
Take-up reel disk
Supply reel disk
Master plane
Reverse
guide
Figure 4-4.
Supply reel disk
Cassette lock
release shaft
Note:
When the tension band ass'y is pressed in the direction of
the arrow for removal, the catch is hard to be deformed.
Position
pin
Take-up reel disk
Figure 4-6.
Note:
• Check that the reel disk is lower than part A but higher
than part B. If the height is not correct, readjust the reel
disk height by changing the poly-slider washer under the
reel disk.
Figure 4-5.
• Reassembly (Supply reel disk)
1. Clean the reel disk shaft and apply grease (SC-141) to
it.
2. Match the phases of reel disk and reel relay gear, and set
the new reel disk.
3. After checking the reel disk height, wind the tension
band ass'y around the reel disk, and insert into the hole
of tension arm ass'y.
15
VC-A410U
VC-H810U
Note:
Whenever replacing the reel disk, perform the height checking and adjustment.
Reel disk height
adjusting jig
Master plane
10 ± 0.2mm
Notes:
1. Hold the torque gauge by hand so that it is not moved.
2. Do not keep the reel disk in lock state. Do not allow longtime measurement.
4-7 CHECKING AND ADJUSTMENT OF TAKEUP TORQUE IN REWIND MODE
Mechanism chassis
Reel disk
• Remove the cassette housing control assembly.
A
B
• After short-circuiting between TP803 and TP802
provided at operation PWB, plug in the power cord.
Reel disk
Figure 4-7.
• Setting
1. Set a torque gauge to zero on the scale. Place it on the
supply reel disk.
2. Press the rewind button.
3. To calculate the remaining capacity, slowly rotate the
take-up reel disk, and then shift it into the rewind mode.
4-6 CHECKING AND ADJUSTMENT OF TAKEUP TORQUE IN FAST FORWARD MODE
• Remove the cassette housing control assembly.
• After short-circuiting between TP803 and TP802
provided at operation PWB, plug in the power cord.
• Checking
1. Turn the torque gauge slowly (one rotation every 2 to 3
seconds) by hand in the CCW direction.
2. Make sure that the indication of torque gauge is not less
than 30mN·m (306gf·cm).
• Setting
1. Set a torque gauge to zero on the scale. Place it on the
take-up reel disk.
2. Press the FF button.
3. To calculate the remaining capacity of the play back
mode, slowly rotate the supply reel disk, and then shift
it into the forward mode.
Torque gauge
30mN·m (306gf·cm)
or more
• Checking
1. Turn the torque gauge slowly (one rotation every 2 to 3
seconds) by hand in the CW direction.
2. Make sure that the indication of torque gauge is not less
than 30mN·m (306gf·cm).
CCW
The gauge is held at
its maximum value.
(Red mark)
Torque gauge
Supply reel disk
CW
30mN·m (306gf·cm)
or more
The gauge is held at
its maximum value.
(Red mark)
Idler ass'y
Figure 4-9.
• Adjustment
1. If the rewind winding-up torque is less than the specified
value, clean the capstan D.D. motor pulley, drive belt,
and limiter pulley with cleaning liquid, rewind again, and
check the winding-up torque.
2. If the winding-up torque is still out of range, replace the
drive belt.
Idler ass'y
Figure 4-8.
• Adjustment
1. If the FF winding-up torque is less than the specified
value, clean the capstan D.D. motor pulley, drive belt,
and limiter pulley with cleaning liquid, and check again.
2. If the torque is less than the set value, replace the reel
belt.
16
VC-A410U
VC-H810U
Notes:
1. Hold the torque gauge by hand so that it is not moved.
2. Do not keep the reel disk in lock state. Do not allow longtime measurement.
4-9 CHECKING AND ADJUSTMENT OF TAKEUP TORQUE IN VIDEO SEARCH REWIND
MODE
4-8 CHECKING AND ADJUSTMENT OF TAKEUP TORQUE IN RECORD/PLAYBACK
MODE
• After short-circuiting between TP803 and TP802
provided at operation PWB, plug in the power cord.
• Remove the cassette housing control assembly.
• Setting
Press the playback button and rewind button to set the
video search rewinding mode.
• Remove the cassette housing control assembly.
• After short-circuiting between TP803 and TP802
provided at operation PWB, plug in the power cord.
• Turn off the power switch.
• Open the cassette torque meter lid, and fix it with
tape.
• Load the cassette torque meter into the unit.
• Put the weight (500g) on the cassette torque meter.
• Turn on the power switch.
• Press the picture record button, and set EP picture
record mode (x3).
• Checking
Place the torque gauge on the supply reel disk, and turn it
counterclockwise very slowly (one rotation every 1 to 2
seconds) and check that the torque is within the set value
14.0 ± 3.9mN⋅m. (144 ± 40gf⋅cm)
Torque gauge
Set value EP6.9 ± 2.5mN⋅m (70 ± 25gf⋅cm)
CCW
500g
Cassette torque meter
Supply reel disk
Figure 4-10.
• Checking
1. Make sure that value is within the setting 6.9 ± 2.5mN·m
(70 ± 25gf·cm).
2. The winding-up torque fluctuates due to variation of
rotation torque of limiter pulley ass'y. Read the center
value of fluctuation as setting.
3. Set the EP record mode (x3) and make sure that the
winding-up torque is within setting.
Figure 4-11.
Note:
Surely put the torque gauge on the reel disk to measure. If
the torque gauge is raised, accurate measurement is
impossible.
• Adjustment
If the rewinding playback winding-up torque is not within the
setting, replace the limiter pulley assembly.
• Adjustment
If the playback winding-up torque is not within the setting,
replace the limiter pulley assembly.
Note:
When the torque cassette is set, put a weight (500g) to
prevent rise.
When the cassette torque meter is taken out.
Turn off the power switch.
Note:
The winding-up torque fluctuates due to variation of rotation torque of supply reel disk. Read the center value of
fluctuation as setting.
17
VC-A410U
VC-H810U
4-10 CHECKING THE VIDEO SEARCH REWIND
BACK TENSION
• Remove the cassette housing control assembly.
• After short-circuiting between TP803 and TP802
provided at operation PWB, plug in the power cord.
Tension gauge
900 - 1,200gf
Pinch roller
• Checking
1. After pressing the play button, press the rewind button,
and set the video search rewind mode.
2. Place the torque gauge on the take-up reel disk, and turn
it counterclockwise very slowly (one rotation every 2 to
3 seconds) and check that the torque is within the set
value 3.4 ± 1.5mN⋅m (35 ± 15gf⋅cm).
Capstan shaft
Tension gauge adapter
Figure 4-13.
Torque gauge
1. Detach the pinch roller from the capstan shaft.
Do not separate excessively. Or the pinch lever and
pinch double action lever may disengage.
2. Engage the tension gauge adapter with the pinch roller
shaft, and pull in the arrow direction.
3. Gradually return the pinch roller, and measure the
pulling force when the pinch roller contacts the capstan
shaft.
4. Make sure that the measured value is within setting 9.0
N to 11.8 N (900 to 1,200gf).
CCW
Take-up reel disk
4-12 CHECKING AND ADJUSTMENT OF
TENSION POLE POSITION
• Remove the cassette housing control assembly.
Figure 4-12.
• After short-circuiting between TP803 and TP802
provided at operation PWB, plug in the power cord.
Notes:
Set the torque gauge securely on the take-up reel disk.
If it is not secure, the measurement will be incorrect.
4-11 CHECKING
PRESSURE
THE
PINCH
•
1.
2.
3.
4.
5.
6.
ROLLER
• Remove the cassette housing control assembly.
• After short-circuiting between TP803 and TP802
provided at operation PWB, plug in the power cord.
Setting
Turn off the power switch.
Open the cassette tape (T-120), and fix with tape.
Set the cassette tape in loading state.
Put the weight (500g) on the cassette tape.
Turn on the power switch.
Make the adjustment with the beginning of a T-120 tape.
(T-120)
• Checking
Press the play button to set the playback mode.
500g
Weight to prevent
float (500g)
Figure 4-14.
• Checking
1. Set a cassette tape, push the REC button to place the
unit in the SP record mode. Now check the tension pole
position.
18
VC-A410U
VC-H810U
2. Visually check to see if the right edge of the tension pole
is within the 2.3 ± 0.25 from the right edge of the Sup
guide shaft.
Tension pole adjuster adjusting range
Tension pole adjuster
90°
Sup guide shaft
Tension pole
90°
2.3 ± 0.25
Make the adjustment with the beginning of a T-120 tape.
Figure 4-18.
Figure 4-15.
Adjust so that the delta mark of tension pole adjuster is
within 90° range (left, right).
At left side from the center line
4-13 CHECKING AND ADJUSTMENT OF
RECORD/PLAYBACK BACK TENSION
• Remove the cassette housing control assembly.
• After short-circuiting between TP803 and TP802
provided at operation PWB, plug in the power cord.
•
1.
2.
3.
4.
5.
2.3 ± 0.25
Figure 4-16.
Insert the slotted screwdriver in the tension pole adjuster,
and rotate counterclockwise.
Setting
Turn off the power switch.
Open the torque cassette meter and fix with tape.
Set the cassette tape in loading state.
Put the weight (500g) on the cassette torque meter.
Turn on the power switch.
At right side from the center line
500g
Weight to prevent
float (500g)
Cassette torque
meter
2.3 ± 0.25
Figure 4-19.
Figure 4-17.
• Checking
1. Push the REC button to place the unit in the SP record
mode.
2. At this time ascertain that the back tension is within the
setting (36.5 to 52g·cm) by seeing the indication of
torque cassette meter.
Insert the slotted screwdriver in the tension pole adjuster,
and rotate clockwise.
19
VC-A410U
VC-H810U
• Adjustment
1. If the indication of torque cassette meter is lower than
the setting, shift the tension spring engagement to the
part A.
2. If the indication of torque cassette meter is higher than
the setting, shift the tension spring engagement to the
part B.
A
• Checking the brake torque at the take-up side
Torque gauge
Tension arm
B
CW
CCW
Take-up reel
disk
Tension spring
Figure 4-20.
CCW: 4.9~13.7mN⋅m (50~140gf⋅cm)
CW:
3.9~10.8mN⋅m (40~110gf⋅cm)
4-14 CHECKING THE BRAKE TORQUE
• Checking the brake torque at the supply side
Figure 4-22.
• Remove the cassette housing control assembly.
Torque gauge
CCW
• After short-circuiting between TP803 and TP802
provided at operation PWB, plug in the power cord.
CW
•
1.
2.
3.
Supply reel disk
Setting
Switch from the FF mode to the STOP mode.
Disconnect the power cord.
Set a torque gauge to zero on the scale. Place it on the
take-up reel disk.
• Checking
1. Turn the torque gauge at a rate of about one turn/2 sec
in the CCW direction/CW direction so that the reel disk
and torque gauge pointer rotates at equal speed and
make sure that the value is within the setting (CCW
direction: 4.9 to 13.7mN·m (50 to 140gf·cm), CW direction: 3.9 to 10.8 mN·m (40 to 110gf·cm).
CCW: 2.9~9.8mN⋅m (30~100gf⋅cm)
CW:
4.9~13.7mN⋅m (50~140gf⋅cm)
Figure 4-21.
• Remove the cassette housing control assembly.
• After short-circuiting between TP803 and TP802
provided at operation PWB, plug in the power cord.
2. Adjustment of the brake torque at the supply side and the
take-up side
• Unless the supply side brake torque or take-up side
brake torque is within the setting, clean the felt surface
of reel disk (supply, take-up) brake lever, check again
the brake torque.
• If value cannot be set within the setting yet, replace the
main brake ass'y or main brake spring.
• Setting
1. Set a torque gauge to zero on the scale. Place it on the
supply reel disk.
2. Switch from the FF mode to the STOP mode.
3. Disconnect the power cord.
• Checking
Turn the torque gauge at a rate of about one turn/2 sec
in the CW direction/CCW direction with respect to the
supply reel disk so that the reel disk and torque gauge
pointer rotate at equal speed, and make sure that the
value is within the setting (CW direction: 4.9 to 13.7mN·m
(50 to 140gf·cm); CCW direction: 2.9 to 9.8mN·m (30 to
100gf·cm).
20
VC-A410U
VC-H810U
C head front section) (See the figure below.)
3. Align the left end of gear of A/C head arm with the
punched mark of chassis, tentatively tighten the screws
1 and 2 so as to ensure smooth motion of A/C head
arm. Tentative tightening torque must be 0.15 to 0.20
N·m (1.5 to 2.0kgf·cm).
4-15 REPLACEMENT OF A/C (AUDIO/CONTROL)
HEAD
1. Remove the cassette housing control assembly.
2. In unloading state unplug the power cord.
• Removal
1. Remove the screws 123, Azimuth screw, Tilt screw.
2. Unsolder the PWB fitted to the A/C head.
Notes:
1. When replacing, never touch the head. If you touched,
clean with the cleaning liquid.
2. When removing the screw 3, take care so that the
spring may out.
1
3
Height screw
2
Left end of A/C head arm gear
Punched line mark on chassis
Figure 4-25.
3 Tilt screw
Azimuth screw
Note:
1. If the screws 1 and 2 are tighten tentatively too loose,
the azimuth and height of A/C head may change when
they are finally tightened. Therefore care must be taken.
2. After completion of A/C head be sure to adjust tape
running. (Execute the running adjustment by the method
described in 4-18.)
Height screw
1
Spring
2
Figure 4-23.
• Replacement
1. Solder the removed PWB to the new head assembly.
2. Adjust the height from the A/C head arm (lower surface)
to the A/C head plate to 10.8mm with slide calipers. (3
places of azimuth screw section, tilt screw section and A/
Solder
New A/C head ass'y
A/C head PWB
Never touch the head
A/C head plate
10.8mm
10.8mm
Figure 4-24.
21
VC-A410U
VC-H810U
4-16 A/C HEAD HEIGHT ROUGH ADJUSTMENT
4-17 HEIGHT ADJUSTMENT OF REVERSE
GUIDE
• Setting
Azimuth screw
1. Adjust the height from the mechanism chassis to the
reverse guide lower flange to 13.38 mm, using the
reverse guide height adjustment jig, in tape loading
state. (Refer to Figure 4-28 (a) (b).)
Reverse guide
Reverse guide height
adjusting jig
Height screw
Reverse guide height
adjusting jig
Tilt screw
Cassette tape
Mechanism
chassis
13.38mm
(b)
(a)
Figure 4-28.
500g
Weight to prevent
float (500g)
2. Rotate counterclockwise the reverse guide height adjustment nut 1/10 turn. (For height adjustment use the
reverse guide height adjustment box driver (JiGDRiVER
11055)).
Mechanism chassis
Figure 4-26.
Box driver
CCW
1. Set the cassette tape in the unit.
2. Press the PLAY button to put the unit in the playback
mode.
3. Roughly adjust the height of the A/C head by turning the
height screw until the tape is in the position shown
below.
Height adjusting nut
A/C head
Tape
0.3mm
Figure 4-29.
Figure 4-27.
3. Set the tape, and check for tape crease near the reverse
guide in the playback mode.
If crease is found, turn the reverse guide adjustment nut
to remove crease. (As for crease check refer to Figure 430.)
• Adjustment
Adjust the height screw visually so that the control head is
visible 0.3mm below the bottom of the tape.
A
Capstan
motor shaft
Fixing guide
500g
Weight to
prevent float (500g)
Mechanism
chassis
Reverse guide
An example of
crease near the
reverse guide
* Check for crease from the A direction.
Figure 4-30.
22
VC-A410U
VC-H810U
Notes:
1. Previously set the tracking control in the center position,
and adjust the envelop waveform to maximum with X
value adjustment nut. Thereby the tape run rough adjustment is facilitated.
2. Especially the outlet side envelope waveform must have
higher flatness.
4-18 ADJUSTMENT OF TAPE DRIVE TRAIN
1. Tape run rough adjustment
1 Remove the cassette housing control assembly.
2 After shortcircuiting between TP803 and TP802 provided at operation PWB, plug in the power cord.
3 Check and adjust the position of the tension pole.
(See 4-12.)
4 Check and adjust the video search rewind back
tension. (See 4-10.)
5 Connect the oscilloscope to the test point for PB
CHROMA envelope output (TP201). Set the synchronism of the oscilloscope to EXT. The PB
CHROMA signal is to be triggered by the head
switching pulse (TP202).
6 Set the alignment tape (VROATSV) to play. (Put a
500g weight on the cassette tape to prevent lift of
cassette tape.)
Figure 4-32.
2. Adjustment of A/C head height and azimuth
1 Perform the initial setting of A/C head position by the
method stated in "4-15 Replacement 3".
2 Connect the oscilloscope to the audio output terminal.
3 Using the alignment tape in which 1 kHz linear audio
signal has been recorded, adjust the height screw so
as to get max audio output.
4 Using the alignment tape in which 7 kHz linear audio
signal has been recorded, adjust the azimuth screw
so as to get max audio output.
5 The adjustment of 3 and 4 twice or three times
repeat, and finally adjust 4.
Guide roller
Cassette Tape
500g
Weight of 500g
Figure 4-31.
7 Press the tracking button (+), (–) and change the
envelope waveform from max to min and from min to
max. At this time make sure that the envelope
waveform changes nearly parallel.
8 Unless the envelope waveform changes nearly parallel, adjust the height of supply side and take-up
side guide roller so that the envelope waveform
changes nearly parallel. (For envelop adjustment
procedure refer to Figure 4-35.)
9 Turn the tilt screw to remove the tape crease at the
fixing guide flange.
Playback the tape and check for tape crease at the
fixing guide flange.
(1) If there is no tape crease
Turn the tilt screw clockwise so that tape crease
appears once at the flange, and then return the tilt
screw so that the crease disappears.
(2) If there is tape crease
Turn counterclockwise the tilt screw so that the
tape crease disappears.
(Reference) If the tilt screw is turned clockwise
crease appears at the lower flange.
For X value adjustment
Adjust the X value, turning the geartype screwdriver.
Figure 4-33.
3. Tape run adjustment
1 Connect the oscilloscope to PB CHROMA envelope
output test point, set oscilloscope sync to EXT,
trigger-input the PB CHROMA signal (head switching pulse).
2 Rough adjustment of X value
Tentatively fix A/C head arm screws 1 and 2 by the
method described in 4-15 "Replacement 3".
Playback the alignment tape (VROATSV) and
shortcircuit between TP801 and TP802. As a result
the auto-tracking is automatically cancelled, so that
the X value adjustment mode is set.
Move the A/C head with the X value adjustment gear
driver (JiGDRiVER-6) by the method shown in Figure 4-33, and adjust the A/C head so as to get the
maximum envelope waveform. (Note: When the A/
C head is adjusted, adjust so that the maximum
envelop waveform is obtained nearest the position
of initial setting made in 4-15.)
23
VC-A410U
VC-H810U
3 Next, press the tracking button (+), (–) and change
the envelope waveform from max to min and from
min to max. At this time adjust the height of supply
and take-up side guide roller with the adjustment
driver (JiGDRiVERH-4) so that the envelope waveform changes nearly parallel.
4 If the tape is lifted or sunk from the helical lead
surface, the PB CHROMA envelope waveform appears as shown in Figure 4-35.
5 Press the tracking button (+), (–) and make sure that
the envelope waveform changes nearly parallel.
6 Finally check tape crease near the reverse guide. If
tape crease is found, remove it as stated in 4-17
"HEIGHT ADJUSTMENT OF REVERSE GUIDE"
item 3.
PB CHROMA
Envelope
CH-1
Figure 4-34.
4. A/C head X value adjustment
1 Tentatively fix A/C head arm screws 1 and 2 by the
method described in 4-15 "Replacement 3".
2 Playback the alignment tape (VROATSV), and
shortcircuit between TP801 and TP802. As a result
the auto-tracking is automatically cancelled, so that
the X value adjustment mode is set.
When the tape is above the helical lead.
Supply side
Adjustment
Supply side guide roller
rotated in clockwise
direction (lowers guide
roller) to flatten
envelope.
CH-2
Head switching pulse
Take-up side
Take-up side guide roller
rotated in clockwise
direction (lowers guide
roller) to flatten
envelope.
When the tape is below the helical lead.
Supply side
Take-up side
Supply side guide roller
rotated in counterclockwise direction (raises
guide roller) to make the
tape float above the helical
lead. The supply
side guide roller is then
rotated in the clockwise
direction to flatten the
envelope.
Take-up side guide roller
rotated in counterclockwise direction (raises
guide roller) to make the
tape float above the
helical lead. The take-up
side guide roller is then
rotated in the clockwise
direction to flatten the
envelope.
Figure 4-35.
3 Move the A/C head with the X value adjustment gear
driver by the method shown in Figure 4-33, and
adjust the A/C head so as to get the maximum
envelope waveform. (Note: At this time adjust so as
to get the maximum envelope waveform nearest the
A/C head position which has been set in case of X
value rough adjustment as stated in 4-18, 3- 2.)
4 Tighten finally the screws 1 and 2. Be sure to
tighten at first the screw 1 and then the screw 2.
Final tightening torque is 0.6N·m (If the screw 2 is
tightened first, the X value may deviate.)
5 Adjust the playback switching point (Refer to the
electric adjustment method.)
6 Playback the self-picture-recorded tape, and check
the flatness of envelope waveform and sound.
Notes:
When the A/C head X value adjustment is performed, be
sure to perform at first X value rough adjustment (refer to 418, 3-2).
1
2
Figure 4-36.
24
VC-A410U
VC-H810U
4-20 REPLACEMENT OF DRUM D.D. MOTOR
4-19 REPLACEMENT OF THE CAPSTAN D.D.
(DIRECT DRIVE) MOTOR
1. Set the ejection mode.
2. Withdraw the main power plug from the socket.
• Remove the mechanism from the main PWB (refer to 22 item 1 When removing the mechanism from the main
PWB ).
•
1.
2.
3.
4.
5.
• Removal (Follow the order of indicated numbers.)
1. Remove the reel belt 1.
2. Remove the three screws 2.
2
Notes:
1. In removing the D.D. stator assembly, part of the drum
earth spring pops out of the pre-load collar.
Be careful not to lose it.
2. Install, so that the D.D. rotor ass'y and upper drum ass'y
mounting direction check holes align.
(Align the upper drum dent with the rotor hole.)
3. Be careful not to damage the upper drum or the video
head.
4. Protect the hole elements from shock due to contact with
D.D. stator or D.D. rotor ass'y.
5. After installation adjust the playback switching point for
adjustment of servo circuit.
Capstan D.D. motor
control PWB
Capstan D.D.
motor
1
Removal (Perform in numerical order.)
Disconnect the FFC cable 1.
Unscrew the D.D. stator assembly fixing screws 2.
Take out the D.D. stator assembly 3.
Unscrew the D.D. rotor assembly fixing screws 4.
Take out the D.D. rotor assembly 5.
Reel belt
2
D.D. stator ass'y
Figure 4-37.
3
• Reassembly
1. Taking care so that the capstan shaft does not contact
the mechanism chassis, set its position on the mechanism chassis, and then install with the three screws.
2. Install the reel belt.
Notes:
1. After installing the capstan D.D. motor, be sure to rotate
the capstan D.D. motor and check the movement.
2. Set the tape, and check for the tape crease near the
reverse guide in the playback mode. Adjust the A/C
head and azimuth as stated in 4-18 item 2. If crease is
found, adjust as stated in 4-17 "HEIGHT ADJUSTMENT
OF REVERSE GUIDE".
1
FFC
4
4
5
D.D. rotor ass'y
Upper drum
Figure 4-38.
25
VC-A410U
VC-H810U
4-21 REPLACING THE UPPER AND LOWER
DRUM ASSEMBLY
4-22 ASSEMBLING OF PHASE MATCHING
MECHANISM COMPONENTS
• Assemble the phase matching mechanism components in the following order.
1. Assemble the pinch roller assembly and pinch drive
cam.
2. Mounting the shifter (on the back of the mechanism
chassis).
3. Mounting the master cam (on the back of the mechanism chassis).
4. Assemble the connection gear, slow brake and loading
motor parts.
• Replacement (Perform in the numerical order)
1 Remove the motor as stated in 4-20 D.D. motor replacement.
2 Remove the drum earth brush ass’y 2.
3 Remove the drum base 3 from the upper and lower
drum assembly 1.
[Cares when replacing the drum]
1. Be careful so that the drum earth brush is not lost.
2. Do not touch directly the drum surface.
3. Fit gently the screwdriver to the screws.
4. Since the drum assembly is an extremely precise assembly, it must be handled with utmost care.
5. Make sure that the drum surface is free from dust, dirt
and foreign substances.
6. After replacing the drum be sure to perform the tape
running adjustment.
After that, perform also the electrical adjustment.
• Playback switching point adjustment
• X-position adjustment and check
• Standard and x-3 slow tracking adjustment
7. After replacing the drum clean the drum.
• PINCH DRIVE CAM AND PINCH ROLLER
ASSEMBLING METHOD.
(Place the following parts in position in numerical order.)
(1)Reverse drive lever 1
(2)Reverse guide spring 2
(3)Reverse guide lever ass’y 3
(4)Reverse guide height adjusting nut 4
(5)Pinch drive cam 5
(6)Pinch roller ass’y 6
7
(7)Open lever 7
6
2
4
1
3
1
2
5
3
Figure 4-40.
Figure 4-39.
26
VC-A410U
VC-H810U
1Insert Reverse Guide Lever Ass’y
Insert reverse guide lever ass'y
2 Insert pinch drive cam
Align here.
Turn the reverse guide lever
assembly counterclockwise
to the stopper.
Fit the pinch drive cam so that the notch of pinch
drive cam aligns with the dent of pinch drive lever
assembly.
Fit the pinch drive cam so that the notch of
pinch drive lever assembly aligns with the
half-round notch of chassis.
Pinch drive lever ass'y
Figure 4-41-1.
2Insert Pinch Roller/Pinch Double Action Lever Ass’y.
3Insert Open Lever.
Pinch Roller Double
Action Lever Ass'y
Open lever
Phase Matching Point 2
Figure 4-41-2.
Figure 4-41-3.
27
VC-A410U
VC-H810U
1. Make sure that the loading gear is at the Phase-Matching point 1 as shown below.
2. Install, paying attention to insert point 5 and release
point 3.
3. For the phase matching at the insert point 1, see the
Phase-Matching point 2 as shown below.
4. Finally fix the inserts 1 and 4.
4-23 INSTALLING THE SHIFTER
Drum
Capstan
D.D. motor
Reel pulley
Phase-Matching
point 2
(Bottom side of mechanism chassis)
Figure 4-42.
Loading gear (T)
Insert
point 1
Round mark
Shaft 1
Sifter
Half round notch
Insert
point 3
Insert
point 2
Insert
point 4
Shaft 1
Rotation
point 2
Shaft 4
Release
point 3
Shaft 1
Phase-matching
point 1
Figure 4-43.
28
Insert
point 5
VC-A410U
VC-H810U
4-24 INSTALLING THE MASTER CAM (AT
REAR SIDE OF MECHANISM CHASSIS)
4-25 REPLACEMENT OF LOADING MOTOR
• Removal
1. Make sure beforehand that the shifter is at the point as
shown below.
2. Place the master cam in the position as shown below.
E ring
(XRESJ30-06000)
Master cam
Apply grease
Apply grease
Fully turn
clockwise
Fully turn counterclockwise
Face the wide tooth side ward
No grease
Figure 4-44-1.
Note:
See the figure below for the phase matching between the
master cam and the casecon drive gear.
3. Finally fix with the E ring.
Figure 4-45.
Master cam
Casecon drive gear
• Replacement
Remove the loading motor, and install the replacement
loading motor as shown below.
Half-round notch
Round mark
10.2 +0.2
–0.2 mm
When installing the master cam,
align the casecon drive gear
round mark with the half-round
notch of master cam.
Figure 4-44-2.
Figure 4-46.
The loading motor pressing-in must be less than 14.7 N
(1,500 gf).
Adjust the distance between motor and pulley to 10.2
+0.2
–0.2 mm).
29
VC-A410U
VC-H810U
4-26 ASSEMBLY OF CASSETTE HOUSING
1. Drive Gear and R Drive angle ass’y
MSPRT0381AJFJ
Apply grease
Apply grease
Apply grease
Figure 4-47.
2. Synchro Gear, Drive Gear L and Drive Gear R
LANGF9592AJFW
Top surface should be free from scratches or soil.
Drive angle
Drive gear R
Frame
Figure 4-48.
30
VC-A410U
VC-H810U
5. ELECTRICAL ADJUSTMENT
Notes:
• Before the adjustment:
Electrical adjustments discussed here are often required after replacement of electronic components and mechanical
parts such as video heads.
Check that the mechanism and all electric components are in good working condition prior to the adjustments,otherwise
adjustments can not be completed.
• Instruments required:
• Color TV monitor
• Audio signal generator
• Blank video cassette tape
• Screwdriver for adjustment
• RF signal generator
• Dual-trace oscilloscope
• AC milli-voltmeter
• Alignment tape (VROEFZCS or VROEFZHS)
• Color bar generator
TP201~204
R701
Figure 5-1.
31
VC-A410U
VC-H810U
SERVO CIRCUIT ADJUSTMENT
5-2 ADJUSTMENT OF FV (False Vertical
Sync) OF STILL PICTURE
5-1 ADJUSTMENT OF HEAD SWITCHING
POINT
Measuring
instrument
Dual-trace oscilloscope
Mode
Playback
Cassette
Alignment tape
(VROEFZCS or VROEFZHS)
Test point
VIDEO OUT jack to CH2
TP202 (Sig.)~TP203 (GND) to CH1
Control
R701 Head switching point adjustment control
Specification
5.5 ± 0.5H (lines)
CH-1
HEAD
SWITCHING
PULSE
Mode
Playback still
Cassette
Self-recorded tape (SP mode)
(See Note below 2)
Control
Tracking control buttons(+) or (–)
Specification
No vertical jitter of picture
5-3 CHECKING OF OFF TRACK
CH-1: 1V/dev 50µsec/dev
CH-2: 2V/dev 50µsec/dev
5.5±0.5H (lines)
Color TV monitor
1. Play a cassette which was recorded by the unit in SP
mode.
2. Press the PAUSE/STILL button to freeze the picture.
3. Look at the monitor screen and adjust (+) or (–) TRACKING buttons so that the vertical jitter of the picture is
minimized.
4. Play and freeze the self-recorded tape in EP mode and
make sure vertical jitter of the picture is not noticeable.
Note:
1 The FV goes back to the it’s initial state when the unit is
put into the system controller reset mode due to power
failure, etc.
In this case, preset the FV once again.
2 Self-recorded tape is a cassette whose program was
recorded by the unit being adjusted.
1. Remove the front panel and play the alignment tape.
2. Connect a dual-trace oscilloscope to the VIDEO OUT
jack and TP202 (Sig.) and TP203 (GND).
(Trigger the oscilloscope with the head switching pulse
on TP202.)
3. Playback the alignment tape, and then short circuit
between TP801 and TP802 on the operation PWB.
4. Adjust R701 so that the leading edge of the head
switching pulse is 5.5H (lines) ahead of the vertical sync
as shown in Figure 5-2.
5. Cancel the short circuited.
CH-2
VIDEO OUT
Measuring
instrument
V-sync.
Measuring
instrument
Color TV monitor
Mode
Playback
Cassette
Self-recorded tape (EP mode)
(See Note below)
Control
Tracking control buttons(+) or (–)
Specification
No Poor picture and Hi-Fi sound
1. Play a cassette which was recorded by the unit in EP
mode.
2. Short circuit between TP802 on the main PWB, and
press both CH button (+) and CH button (–) at same time.
3. Press the tracking buttons (+) and (–) 20 times each to
bring the tracking off center. Make sure that:
1) There is nothing unusual on the playback screen.
2) There is nothing unusual in the Hi-Fi sound (for the HiFi models only).
4. Cancel the short circuit.
Note:
Self-recorded tape is a cassette whose program was recorded by the unit being adjusted.
Figure 5-2.
32
33
0
19.812
CA/END
CS/EJ
1 1
1 1
Mode detection inside
S sensor
Open
S sensor Close
0 0
EJ
10.354 12.812
0
5
10
15
20
25
Mode detection outside
Mode detection inside
(D708 SW A)
Mode detection outside
(D709 SW B)
Mode check
Cam mark
G mechanical timing
0
0
0
UL
0
1
1
0
0
0
0
0
0
ULD
PU1
PU2
VSR
PB
SLOW
FF
STOP
0
1
1
0
1
1
1
1
0
sensor B
1 1
1
Mode detection outside
0
1 1
PU
PU1
179
180
sensor A
1
1
120
Mode detection inside
0 1
1 1
1
1 or 0
0
0
UL
81
CS/EJ
1
0
0
60
Cam graph E
0 0
1 0
PU2
PU2
200
240
0 0 0
1 1 0
VSR
VSR
233
0
1
0
0
PB
PB
265
0
0
0
1
SLW
300
0
1
SLOW
282
0 0
0 1
FF
FF
316
0
1
0
0
STP
STOP
334
380
Fullloading
Cassette
inserting
Insert cassette.
Loading motor turns in reverse
direction and master cam
counterclockwise.
Start sensor close.
(Cassette is judged
caught halfway.)
NO
End
End
YES
Is drum FG pulse outputted ?
Loading motor stop.
Cam switch is at PB position.
Pinch roller comes into contact.
Tape loading.
Drum motor starts.
YES
NO
Unloading
Are start/end sensors at low level NO
before cassette insertion ?
(Cassette LED or some other part
is judged defective.)
YES
Does mechanism position sw.
come off within 2.5 sec.?
Loading motor starts in normal
direction and master cam counter
clockwise.
STOP
Cassette is ejected and loading
motor stops.
CASSETTE INSERTION
Double action rack slides.
* This flowchart describes the outline of the mechanism’s operation, but does not give its details.
MECHANISM OPERATION FLOWCHART
6. MECHANISM OPERATION FLOWCHART AND TROUBLESHOOTING GUIDE
VC-A410U
VC-H810U
REC/PLAY
34
VSF
End
Set capstan motor to search
speed.
Press FF key.
PLAY
Unloading
End
YES
Is take-up reel sensor signal
outputted ?
Picture appears.
Capstan motor turns
counterclockwise.
Press REC/PLAY key.
STOP
NO
Slow brake
pressing
STILL
STOP
Unloading
End
YES
Is take-up reel sensor signal
outputted ?
End
Stop loading motor.
Cam switch is at VSR
position.
Press pinch roller.
Turn loading motor
counterclockwise.
Cam switch is at PU1 position.
Release the supply auxiliary
brake.
Loading motor turns clockwise.
Turn capstan motor in
reverse direction.
Stop loading motor.
Cam switch is at PU2 position.
Release pinch roller.
Loading motor turns
clockwise and master
cam counterclockwise.
Set capstan motor to search
speed.
Pinch
roller
pressing
Idler
swinging
Pinch
roller
releasing
VSR
Press REW key.
PLAY
Stop capstan motor.
Capstan motor turns in
reverse direction.
Press STOP key.
REC/PLAY
End
Capstan motor stops.
Loading motor stops.
Cam switch is at STILL
position.
Slow brake comes into
contact with capstan motor.
Loading motor turns in
counterclockwise direction
and master cam clockwise.
Press STILL key.
PLAY
NO
PLAY
End
Cam switch is at PB position.
Capstan motor turns
counterclockwise. PB speed.
Loading motor turns counterclockwise and master cam
clockwise.
Press PLAY Key.
VSR
VC-A410U
VC-H810U
Brake
function
FF/REW
operation
FF/REW
STOP
35
End
Loading motor stops.
Cam switch is at Stop
position.
Stop capstan motor.
Loading motor turns counterclockwise.
Press STOP key.
FF/REW
End
Turn capstan motor in
normal or reverse direction,
after the remaining tape has
been detected.
Press FF/REW key.
STOP
Cassette
eject
Tape
unloading
CASSETTE EJECT
End
Capstan motor
stops.
Loading motor
stops.
Cam switch is at
Eject position.
Loading motor turns
clockwise.
Capstan motor turns
clockwise.
YES
Does the take-up
reel pulse output
two edges ?
YES
4 supply reel pulses
outputted ?
NO
NO
Capstan motor turns
counterclockwise in about
2 seconds.
Capstan motor turns
clockwise.
Stop loading motor.
Cam switch is at UL position.
Capstan motor turns in reverse direction.
Loading motor turns in clockwise and master cam
counterclockwise.
Press EJECT key.
STOP
VC-A410U
VC-H810U
NO
36
The cassette tape
is presumably
damaged.
YES
Is the pulse
NO
outputted from reel
sensor ?
YES
Are idler wheel
NO
ass’y and reel disk
in mesh ?
YES
Does capstan
NO
motor turn in FF (or
REW) direction ?
YES
Is master cam at
FF position ?
Replace the reel
sensor.
Replace the idler
ass’y.
Replace the
capstan motor.
YES
Are Vco 12V and
Vcc 5V applied ?
Loading motor
control system
in trouble.
YES
Modes changing
smoothly through
cam switch ?
YES
Does loading
motor operate ?
Press FF key.
1. FF/REW FAILURE (NO TAPE WINDING)
NO
NO
NO
Voltage supply
system in trouble.
Mode sensor
system in trouble
or master cam
malpositioned.
Loading motor is
damaged. Replace
it.
YES
Is voltage applied NO
to loading motor ?
MECHANISM TROUBLESHOOTING
Voltage supply
system in trouble.
NO
Check main PWB.
YES
Is the pulse
NO
outputted from reel
sensor ?
YES
Are idler wheel
NO
ass'y and reel disk
in mesh ?
YES
Does capstan
motor turn ?
YES
Is the master cam NO
at PB position ?
Replace the reel
sensor.
Replace the idler
ass’y.
Replace the
capstan motor.
YES
Are Vco 12V and
Vcc 5V applied ?
Loading motor
control system
in trouble.
YES
Modes changing
smoothly through
cam switch ?
YES
Does loading
motor operate ?
2. REC/PLAY FAILURE (MODE RELEASE)
NO
NO
Voltage supply
system in trouble.
Loading motor is
damaged. Replace
it.
YES
Is voltage applied NO
to loading motor ?
Voltage supply
system in trouble.
VC-A410U
VC-H810U
NO
NO
37
Check main PWB.
YES
Is pulse outputted NO
from reel sensor ?
YES
Is supply reel disk NO
winding torque
normal ?
YES
Are idler wheel
NO
ass’y and supply
reel disk in mesh ?
YES
Master cam
shifting to VSR
position ?
Press REW key.
YES
Is Playback
function normal ?
Replace reel
sensor.
Replace limiter
pulley ass’y.
Replace idler
gear ass’y.
Go to 2. REC/
PLAY FAILURE
routine.
Go to 2. REC/
PLAY FAILURE
routine.
3. WINDING FAILURE AT VSR
Replace loading motor block.
YES
Is unusual sound heard during
loading/unloading ?
NO
Unusual sound heard with pinch
roller lever going up or down ?
NO
Is unusal sound heard during
cassette control running ?
4-i) Unusual sound in cassette
insertion and ejection mode
YES
YES
4. UNUSUAL SOUND IN EACH MODE
Check pinch roller drive cam, pinch roller
drive lever and reverse guide for their actions.
Replace damaged one with new one.
Replace cassette control ass’y.
VC-A410U
VC-H810U
38
Check drive system’s gears for
damage. Replace damaged gear
with new one.
• Reel disk
• Limiter pulley ass’y
• Idler wheel ass’y
NO
Turn capstan motor by hand.
Unusual sound heard ?
NO
Drive system out of contact with any
part on main PWB ?
YES
Thrust gap found at reel disk ?
YES
Is reel disk height as specified ?
4-ii) Unusual sound in FF/REW mode
YES
YES
NO
NO
Replace capstan motor.
Rearrange the parts on main PWB.
Check reel disk and main chassis.
And replace defective parts.
Adjust reel disk height.
VC-A410U
VC-H810U
39
The fuse blows out even when it is
replaced with new one.
See FLOW CHART NO.2
<Fuse blown out.>.
Replace IC901.
Check whether the secondary side
photocoupler circuit operates
normally.
YES
Check whether the primary side
photocoupler output control
functions normally.
YES
Check the circuit and replace parts.
(IC901, IC903, etc.)
Check the circuit and replace parts.
(IC901, IC903, Q902, T901, etc.)
NO
NO
When the output voltage fluctuates.
FLOW CHART NO.3
Check for short-circuiting of
rectifying diode and circuit in each
rectifying circuit of secondary circuit.
(D921~928)
Check for leak or short-circuiting of
primary circuit part.
(L901, D901~904, T901, C906,
R904, Q901~902, etc.)
Check the power failure circuit.
(Q705)
Check each rectifier circuits and
short-circuit of secondary circuit.
Check for leak or short-circuiting
of primary circuit part.
(L901, D901~904, T901, C906,
R904, Q901~902, etc.)
Case (2)
Fuse blown out.
FLOW CHART NO.2
NO
NO
NO
NO
NO
Check or place the peripheral circuit
of IC701.
YES
Is there the function control voltage
inputted at the pins(87) and (88)
of IC701?
YES
Does the key switch make good
contact, when the cassette tape is NO
inserted?
Key-in input is not received.
FLOW CHART NO.5
Check switch contact.
Check for short-circuiting of circuit and rectifying diode of each rectifying circuit of secondary
circuit and check for failure of shunt regulator circuit. (D921~928, IC903, C932, C933)
When buzz is heard from the vicinity of power circuit.
No power
Case (1)
Is "H" level applied at pin(1) of
IC701?
YES
Are AT 44V, AT 23V, PC 12V,
AT –24V and filament voltage lines
normal?
YES
Are AT 5V voltage line normal?
YES
Is the normal state restored when
once unplugged power cord is
plugged again after several
seconds?
YES
Is the fuse good?
FLOW CHART NO.4
FLOW CHART NO.1
7. TROUBLESHOOTING
VC-A410U
VC-H810U
40
YES
Replace loading motor.
YES
Is the specified voltage (about 10V) NO
applied at the loading motor terminal
when the cassette tape is inserted?
YES
Does pin(13) of IC706 change to
NO
about 10V when the cassette tape is
inserted?
YES
Does pin(11) of IC706 go to a "H"
NO
(about 1.7V) level when the cassette
tape is inserted?
NO
NO
Check between IC706 and loading
motor.
Check IC706.
Check line pin(9) of IC701 and all
the way up thru to pin(11) of IC706.
Check line start sensor and all the
way up thru to pin(79) of IC701.
Check start sensor shutter.
Check line between at remote
control receiver thru to pin(5) of
IC701.
A cassette tape is not take in.
Does pin(79) of IC701 change from
"H" to "L" level when the cassette
tape is inserted?
YES
NO
Check AT 5V lines.
Replace the remote control receiver
or replace the remote control
transmitter if necessary.
FLOW CHART NO.7
Are start sensor shutter go to open
when the cassette tape is inserted?
Replace IC701.
YES
Is inputted "L" pulse to pin(5) of
IC701?
YES
Is "L" pulse sent out pin(1) terminal of
NO
receiver when the infrared remote
control is activated?
Operation is possible from the VCR,
but no operation is possible from the
infrared remote control.
YES
Is the supply voltage of 5V feed to
NO
pin(3) terminal of remote control
receiver?
YES
No operation is possible from the infrared remote control.
FLOW CHART NO.6
FLOW CHART NO.8
NO
Replace IC701.
YES
Does the master cam mode shifter
operate normally when the cassette
tape is loaded?
YES
NO
Does the end sensor pulse at pin(85) NO
of IC701 change from "L" to "H" level
when the cassette tape is loaded?
YES
Does the start sensor pulse at
pin(79) of IC701 change from "L" to
"H" level when the cassette tape is
loaded?
Check cam switch and all the way
up thru to IC701.
Check end sensor and all the way
up thru to IC701.
Check start sensor and all the way
up thru to IC701.
A cassette tape is taken in, but ejected at once.
VC-A410U
VC-H810U
NO
NO
41
Replace cassette cam, gear, etc.
YES
Does the loading motor run?
YES
NO
Is the specified voltage applied at the NO
loading motor terminal?
YES
Is the voltage about 10V sent out of
pin(15) of IC706?
YES
Is a "H"(about 1.7V) level applied at NO
pin(12) of IC706 when a reel pules
has been inputted?
YES
Are pulses applied at pin(2) of IC701
when the take-up reel disk is turning?
YES
Does the take-up reel disk turn when NO
the capstan motor is running?
YES
NO
Replace loading motor.
Check between IC706 and all the
way up thru to the loading motor.
Check IC706.
Check pin(90) of IC701.
Check take-up reel sensor and all the
way up thru to IC701.
Check reel disk and reel drive unit.
See FLOW CHART NO.12.
NO
Is the supply voltage of 12V feed to
pin(5) of AC connector?
YES
YES
NO
NO
Is the voltage at pin(3) of AC
connector 1.6~2.7V?
YES
NO
NO
Is the voltage more than 2.6V DC
sent in pin(4) of AC connector?
YES
Is the supply voltage of 5V feed to
pin(8) of AC connector?
NO
Replace capstan motor.
Check AT 12V line and motor voltage
selector circuit.
Check between the pin(92) of IC701
and all the way up thru to pin(3) of
AC connector.
Check between the AC connector
and all the way up thru to pin(29)
of IC701.
Check PC 5V line.
Check IC701.
Check Q951 and the AT 5V line.
The capstan motor fails to run.
Is the voltage more than about 2.6V
DC given out of pin(29) of IC701.
YES
NO
Check IC701.
Check IC701 and all the way up thru
to Q951.
FLOW CHART NO.11
Check peripheral circuits for poor
soldering.
YES
Is 5V sent out of the collector of
Q951?
YES
Does the base of Q951 change from NO
about 5.0V to 4.5V?
YES
Does power control(H) signal at
pin(4) of IC701 change from "L" to
"H" level?
No power is turned on.
The cassette tape fails to eject.
Does the capstan motor start when
the EJECT button is pressed?
FLOW CHART NO.10
FLOW CHART NO.9
VC-A410U
VC-H810U
42
FLOW CHART NO.13
NO
NO
NO
Check AT 12V line.
Check between pin(46) of IC701
and all the way up to pin(2) of
IC706.
Check PC 5V line.
Check IC701.
Replace IC701.
YES
Is V-H.SW.P pulse given out of
pin(23) of IC701?
YES
Is drum PG signal given out of
pin(66) of IC701?
YES
Is drum PG signal given out of
pin(7) of IC706?
NO
NO
NO
Check IC701.
Check line between pin(7) of IC706
and all the way up thru to
pin(66) of IC701.
Check or replace drum motor.
YES
Check pin(4), (5), (6) of IC706 and
periperal circuits.
NO
Replace IC706.
The drum motor runs only for a few seconds.
Check or replace drum motor.
YES
Is the supply voltage of 12V feed to
pin(21) of IC706?
YES
Is the voltage more than about 2.6V
applied at pin(2) of IC706?
YES
Is the supply voltage of 5V feed to
pin(3) of IC706?
YES
NO
Are the drum PG and drum FG
signals present on pins(7) and (8) of
IC706?
NO
Check peripheral circuit of IC706.
YES
Is the drum PG signal and drum FG
signal present on pins(66) and (65)
of IC701, respectively?
YES
Is the drum motor rotating?
YES
NO
NO
YES
See FLOW CHART NO.13,14.
Could be lines between IC706
and IC701.
Replace IC701.
Check C723 and readjust R701.
(HEAD SW. POINT control.)
NO
Are there drum PG M.M.signal at
pin(81) of IC701?
The drum motor fails to run.
Is the voltage more than about 2.6V
DC given out of pin(46) of IC701.
FLOW CHART NO.14
No head switching pulse.
FLOW CHART NO.12
VC-A410U
VC-H810U
Check drum FG signal line.
YES
43
Does the IC706 operate normally?
YES
Is the drum control voltage applied
to pin(2) of IC706?
YES
Is the drum APC output at pin(34) of
IC701 and drum AFC output at
pin(32) of IC701 present?
YES
YES
NO
NO
Is the head switching pulse at pin(23) NO
of IC701 present?
NO
Is there drum FG signal at pin(65)
of IC701 present?
In PB mode
Replace drum motor.
Is pin(46) of IC701 in high
impedance?
YES
Check line between pins(34) and
(32) of IC701 and pin(2) of IC706.
Replace IC701.
See FLOW CHART NO.15.
YES
Is there 14.318MHz oscillation at
pins(37) and (38) of IC701?
Drum servo does not function.
FLOW CHART NO.15
NO
NO
YES
Replace IC701.
Check peripheral circuit of pin(50) of
IC701, C770, C771 and R770.
NO
Is the V-SYNC signal(reference) at
pin(50) of IC701?
In REC mode
Check peripheral circuit of X701.
VC-A410U
VC-H810U
44
YES
Adjust the height
of the A/C head.
YES
Does A/C head
NO
operate normally?
NO
Does PB CTL
signal appear at
pin(76) of IC701?
1
Only PB mode inoperative
Replace A/C head.
Replace IC701.
NO
Is there capstan
AFC and APC
at pins(31) and (33)
of IC701?
YES
Check capstan
motor unit and/or
replace.
Check peripheral
circuit of X701.
NO
Is there 14.318MHz YES
oscillation at pins
(37) and (38) of
IC701?
Are REC and/or PB
mode inoperative?
Capstan servo does not function.
FLOW CHART NO.16
2
Check peripheral
circuit of AC
connector.
NO
Check "1"
YES
Does pin(29) of
IC701 operate
normally?
YES
YES
Is there REC CTL
NO
signal output at
Replace IC701.
pins(75) and (74)
of IC701?
NO
YES
Does the capstan
Is there capstan
FG signal appear YES
AFC signal at pin
at pin (67) of IC(31) of IC701?
701?
YES
NO
Check the capstan
Is there capstan
FG signal line betAPC signal at pin
ween pin(6) of AC
(33) of IC701?
connector and pin
(67) of IC701.
Check peripheral
Is the V-SYNC
circuit of pin(50) of NO signal(reference) at
IC701, C770, C771
pin(50) of IC701?
and R770.
Only REC mode inoperative
NO
NO
NO
NO
Check "2"
Replace IC701.
Does PB CTL
signal appear at
pin (76) of IC701?
VC-A410U
VC-H810U
Check the line between pin(52) of IC201
and pin(49) of IC701.
45
Check the AT 5V line.
NO
Is 5V applied to the pin(51) of IC701?
NO
NO
Check the YC 5V line.
NO
Check Q251 periphery.
Check the line between pins(63) and (62) of
IC201 and pins(56) and (57) of IC701.
NO
Is serial data clock signal applied to the
pins(63) and (62) of IC201?
YES
Is 5V applied to the pins(12), (61) and (90) of IC201?
NO
1 External input mode
Check the line between the rear video input terminal
and pin(30) of IC201.
2 U/V tuner mode
Check the line between the pin(25) of U/V tuner and
pin(31) of IC201.
1 Line output: Check Q251 periphery and output terminal periphery.
2 RF output: Check Q251 periphery and tuner pin(6) periphery.
YES
Is picture signal output to the emitter of video output
buffer (Q251)?
YES
Is picture signal output to the pin(47) of IC701 ?
YES
NO
NO
Is picture signal output to the pin(52) of IC201?
Is picture signal input into the pin(49) of IC701?
YES
YES
Is picture signal input into pins(30) and (31) of IC201?
Picture E-E does not appear.
FLOW CHART NO.17
VC-A410U
VC-H810U
46
YES
Check the pins(13) and (14) of IC201
peripheral circuit. (R201, R202, C203)
Check between the pins(24) and
(23) of IC201. (Check C210.)
Is CCD control voltage approx. 5V
applied normally to the pin(37) from
the pin(57) of IC201? Is clock signal
(approx. 7.16 MHz/0.5 Vp-p) for
CCD applied normally to the pin(44)
from the pin(69) of IC201?
YES
Is voltage 5V applied to the CCD section
power terminal pin(36) of IC201?
NO
Is luminance signal (approx. 0.5
Vp-p) input to the pin(39) of IC201?
YES
Check between the pins(39) and
(26) of IC201. (Check C212.)
Check between the pins(21) and
(42) of IC201. (Check C208.)
Check between the pins(18) and
(19) of IC201. (Check C206.)
YES
Is chroma signal (approx. 180
mVp-p/Burst) input into the
pin(58) of IC201?
YES
Is chroma signal (approx. 143
mVp-p/Burst) input into the
pin(46) of IC201?
YES
Is voltage 5V applied to the chroma
power terminal pin(61) of IC201?
NO
NO
NO
NO
Is chroma signal (approx. 180
mVp-p/Burst) output to the
pin(35) of IC201?
YES
Is PRE/REC Vcc 5V applied to the pin(90) of IC201?
NO
YES
Check between the pins(58) and
(35) of IC201. (Check R505, C512.)
Check whether the pins(71) and
(73) of IC201 oscillate (3.58 MHz)?
YES
Check between the pins(60) and
(46) of IC201. (Check C512.)
Check the periphery of pin(61) of
IC201 and YC 5V line.
SP mode: Is record FM signal (approx. 20 mAp-p) output to the pins(88) and (89) (SP1) and pins(86) and (87) (SP2) of IC201?
EP mode: Is record FM signal (approx. 20 mAp-p) output to the IC201 pins(93) and (94) (EP1) and pins(92) and (91) (EP2) of IC201?
NO
NO
NO
NO
Check or replace the cylinder.
Is the luminance signal (approx. 0.5
Vp-p) input and output to the pins(13)
and (14) of IC201, respectively?
YES
Is luminance signal (approx. 0.5
Vp-p) input to the pin(23) of IC201?
YES
Is luminance signal (approx. 0.5
Vp-p) input to the pin(26) of IC201?
YES
Is luminance signal (approx. 0.3
Vp-p) input to the pin(42) of IC201?
YES
NO
Although picture record is possible, color does not appear (E-E mode is possible).
Picture (luminance) record is impossible (E-E mode is possible).
Is luminance signal (approx. 0.5
Vp-p) input to the pin(19) of IC201?
FLOW CHART NO.19
FLOW CHART NO.18
VC-A410U
VC-H810U
47
NO
NO
Replace IC201.
YES
Is luminance signal (approx. 0.5
Vp-p) input to the pin(23) of IC201?
YES
NO
NO
Is luminance signal (approx. 0.5
Vp-p) input to the pin(26) of IC201?
YES
Is luminance signal (approx. 0.5
Vp-p) input to the pin(42) of IC201?
YES
Is luminance signal (approx. 0.5
Vp-p) input to the pin(19) of IC201?
YES
Is the luminance signal (approx. 0.25
NO
Vp-p) input and output to the pins(13),
(14) and (16) of IC201, respectively?
YES
NO
YES
NO
NO
NO
YES
NO
Is chroma signal (approx. 508
mVp-p/Burst) output to the
pin(35) of IC201?
YES
Check between the pin(58) and pin(35)
of IC201. (Check R505, C515.)
Check whether the pin(71) and pin(73)
of IC201 oscillate (3.58 MHz)?
YES
Check between the pin(60) and
pin(46) of IC201. (Check C512.)
Check the periphery of pin(61) of
IC201 and YC 5V line.
Is voltage 5V applied to the CCD section power terminal pin(36) of IC201?
Replace IC201.
Check between the pin(55) and
pin(54) of IC201. (Check C514.)
NO
Is chroma signal (approx. 286
mVp-p/Burst) input into the
pin(54) of IC201?
YES
Is chroma signal (approx. 508
mVp-p/Burst) input into the
pin(58) of IC201?
YES
Is chroma signal (approx. 403
mVp-p/Burst) input into the
pin(46) of IC201?
YES
Is voltage 5V applied to the chroma
power terminal pin(61) of IC201?
Check between the pins(24) and (23) of IC201. (Check C210.)
Is control voltage approx. 5V applied normally to the pin(37) from the pin(57) of IC201? Is CCD clock signal
(approx. 7.16 MHz/0.5 Vp-p) applied to the pin(44) from the pin(69) of IC201?
NO
Is luminance signal (approx. 0.5
Vp-p) input to the pin(39) of IC201?
YES
Check between the pin(39) and
pin(26) of IC201. (Check C212.)
Check between the pin(21) and
pin(42) of IC201. (Check C208.)
Check between the pin(18) and
pin(19) of IC201. (Check C206.)
Check the periphery of pins(13),
(14) and (16) of IC201. (Check
C203, R201-2, L201, C205, R203.)
Check V-H.SW.P. line.
NO
Is V-H.SW.P. applied to the
pin(81) of IC201?
NO
Is luminance signal (approx. 0.4
Vp-p) input to the pin(79) of IC201?
YES
Check between the pins(79) and
(78) of IC201.
Although picture is played back, color does not appear (E-E mode is possible).
Playback picture does not appear (E-E mode is possible).
Is FM signal (approx. 0.4 Vp-p)
input to the pin(78) of IC201?
FLOW CHART NO.21
FLOW CHART NO.20
VC-A410U
VC-H810U
pin(14) pin(9)
pin(48)
Rear input terminal
Tuner audio terminal
48
NO
NO
NO
NO
NO
NO
NO
Check line between emitter of Q501
and pin(28) of IC651.
NO
Is Sub carrier signal (3.58MHz, about
900mVp-p) input to pin(45) of IC651?
Check line between pin(36) of IC651
and pin(21) of IC701.
Check line between pins(43), (42) of
IC651 and pins(17), (18) of IC701.
Check the regulator circuit of Hi-Fi 5V
and PC 9V.
Check the peripheral circuit of front
input terminal.
Check the peripheral circuit of rear
input terminal.
Is there SIF signal from pin(24) of
Tuner?
Replace IC651.
NO
Line output terminal : Check line ranging from pins(53) and (57) of IC651 to the audio
output terminal.
RF output terminal : Check line ranging from pin(59) of IC651 to pin(2) of tuner (TU101).
YES
Line output terminal : Is there audio signal outputted at pins(53) and (57) of IC651?
RF output terminal : Is there audio signal outputted at pin(59) of IC651?
YES
Is "H" level applied at pin(28) of IC651?
YES
Is "L" level applied at pin(36) of IC651?
YES
Are serial data and clock signal at
pins(43), (42) of IC651?
YES
Is the voltage 5V applied to pin(40) of
IC651, 9V applied to pin(58).
YES
pin(15) pin(10)
Front input terminal
Is there signal inputted at each
terminal of IC651 as shown in table?
L-ch R-ch
No Hi-Fi E-E sound heard.
FLOW CHART NO.22
Check the AA-MH harness and A/C head.
YES
Is audio signal on which bias signal is
superposed output to the pin(4) of IC201?
YES
Does the bias oscillation circuit operate
normally?
YES
Is the pin(99) of IC201 in "L" level?
YES
Is audio signal input into the IC201 pin(8)?
Recording in linear audio is impossible
(Hi-Fi E-E mode is normal).
FLOW CHART NO.25
Replace IC651.
YES
Is playback envelope signal output to the
pins(29) and (30) of IC651? (300 mVp-p)
Hi-Fi sound cannot be played back
(E-E mode is normal).
FLOW CHART NO.24
Check the AH-MZ connector.
YES
Is record FM signal output to the pins(21) to
(24) (ch-1)/pins(21) and (22) (ch-2) of IC651?
YES
Is terminal voltage (REC AGC. ADJ.) pin(37)
of IC651 normal?
FLOW CHART NO.23
Hi-Fi sound cannot be recorded
(E-E mode is normal).
NO
NO
NO
NO
NO
NO
Check the bias oscillation circuit (T601, Q602,
Q603).
Check the periphery of pin(99) of IC201.
(R617)
Check the line between the pin(61) of IC651
to the pin(8) of IC201.
Check the A-H.SW.P. line from the pin(27) of
IC651 to the pin(26) of IC701.
NO
Is A-H.SW.P input into the pin(27) of IC651?
YES
Replace IC651.
Check line of Hi-Fi 5V.
NO
Is voltage 5V applied to pin(25) of IC651.
Check Hi-Fi REC CTL line.
NO
Is the pin(29) of IC651 about 3.7V?
YES
Replace IC651.
VC-A410U
VC-H810U
Check the line between the pin(11) of IC201 to
the pin(62) of IC651.
YES
Is audio signal output to the pin(11) of IC201?
YES
Is it possible to confirm the audio signal (PB EQ)
on the pin(100) of IC201?
Linear audio playback is impossible.
(Hi-Fi E-E mode is normal).
FLOW CHART NO.26
NO
NO
NO
Replace IC201.
YES
Check the periphery of pin(99) of IC201. (R617)
NO
Is the pin(99) of IC201 in "L" level?
Readjust the A/C head height.
Replace the AC head.
YES
Is AC head height adjusted properly?
YES
Is the AC head surface clean?
YES
Are MH-AA harness and playback AMP.
peripheral parts normal?
VC-A410U
VC-H810U
49
VC-A410U
VC-H810U
VC-A410U
VC-H810U
8. BLOCK DIAGRAM
SYSTEM SERVO BLOCK DIAGRAM
50~51
VC-A410U
VC-H810U
VC-A410U
VC-H810U
SIGNAL FLOW BLOCK DIAGRAM(VC-A410U)
52~53
Playback luminance signal
Playback chroma signal
Audio playback signal
E-E signal
Recording luminance signal
Recording chroma signal
Audio recording signal
E-E signal(Audio)
VC-A410U
VC-H810U
VC-A410U
VC-H810U
SIGNAL FLOW BLOCK DIAGRAM(VC-H810U)
Playback luminance signal
Playback chroma signal
Audio playback signal
E-E signal
Recording luminance signal
Recording chroma signal
Audio recording signal
E-E signal(Audio)
54~55
VC-A410U
VC-H810U
POWER CIRCUIT BLOCK DIAGRAM
56
VC-A410U
VC-H810U
SCHEMATIC DIAGRAM
• The indicated voltages in the following diagram
are measured with an SSVM, upon receiving
color bars (400 Hz sound signal) in either the
record mode or the play mode voltage is indicated as follows.
4.0 . . . . Record mode (SP)
(4.0) . . . . PB mode (SP)
4.0 . . . . LP mode
4.0 . . . . EP mode
IMPORTANT SAFETY NOTICE:
PARTS MARKED WITH " å" (
) ARE
IMPORTANT FOR MAINTAINING THE SAFETY
OF THE SET.
BE SURE TO REPLACE THESE PARTS WITH
SPECIFIED ONES FOR MAINTAINING THE SAFETY AND PERFORMANCE OF THE SET.
NOTE:
1. The unit of resistance "ohm" is omitted (K: 1000
ohms M: 1 Meg ohm).
2. All resistors are 1/8 watt, unless otherwise noted.
3. All capacitors µF, unless otherwise noted P: µµF.
AVIS DE SECURITE IMPORTANT:
LES PIECES MARQUEES " å" (
) SONT
IMPORTANTES POUR MAINTENIR LA SECURITE
DE L'APPAREIL.
NE REMPLACER CES PIECES QUE PAR DES
PIECES DONT LE NUMERO EST SPECIFIE POUR
MAINTENIR LA SECURITE ET PROTEGER LE
BON FONCTIONNEMENT DE L'APPAREIL.
Voltages and waveform are measured as follows:
• DC voltages are measured with an SSVM placed
between points indicated and chassis ground,
with the supply voltage of 120V AC and all
controls for normal positions.
This circuit diagram is a standard one, actual circuits
printed may be subject to change for product
improvement without prior notice.
57
VC-A410U
VC-H810U
VC-A410U
VC-H810U
9. SCHEMATIC DIAGRAM AND PWB FOIL PATTERN
MAIN CIRCUIT(1)
J
I
H
G
F
E
D
C
B
A
1
2
* VOLTAGE MEASUREMENT MODE
PB .......... Parentheses ( )
REC ....... Without Parentheses
3
4
5
6
7
8
9
10
11
58~59
12
13
14
15
16
17
18
19
20
VC-A410U
VC-H810U
VC-A410U
VC-H810U
MAIN CIRCUIT(2)
J
I
H
G
F
E
D
C
B
A
1
2
* VOLTAGE MEASUREMENT MODE
PB .......... Parentheses ( )
REC ....... Without Parentheses
3
4
5
6
7
8
9
10
11
60~61
12
13
14
15
16
17
18
19
20
VC-A410U
VC-H810U
VC-A410U
VC-H810U
MAIN CIRCUIT(3)
J
I
H
G
F
E
D
C
B
A
1
2
* VOLTAGE MEASUREMENT MODE
PB .......... Parentheses ( )
REC ....... Without Parentheses
3
4
5
6
7
8
9
10
11
62~63
12
13
14
15
16
17
18
19
20
VC-A410U
VC-H810U
VC-A410U
VC-H810U
MAIN CIRCUIT(4)
J
I
H
G
F
E
D
C
B
A
1
2
* VOLTAGE MEASUREMENT MODE
PB .......... Parentheses ( )
REC ....... Without Parentheses
3
4
5
6
7
8
9
10
11
64~65
12
13
14
15
16
17
18
19
20
VC-A410U
VC-H810U
OPERATION CIRCUIT
J
I
H
G
F
E
D
C
B
A
1
2
* VOLTAGE MEASUREMENT MODE
PB .......... Parentheses ( )
REC ....... Without Parentheses
3
4
5
6
66
7
8
9
10
VC-A410U
VC-H810U
PWB FOIL PATTERN
OPERATION PWB
Component Side
J
I
H
G
F
Wiring Side
E
D
C
B
A
1
2
3
4
5
6
67
7
8
9
10
VC-A410U
VC-H810U
VC-A410U
VC-H810U
MAIN PWB
Component Side
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
68~69
12
13
14
15
16
17
18
19
20
VC-A410U
VC-H810U
VC-A410U
VC-H810U
MAIN PWB
Wiring Side
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
70~71
12
13
14
15
16
17
18
19
20
VC-A410U
VC-H810U
-MEMO-
72
VC-A410U
VC-H810U
Part No.
★
Description
10. REPLACEMENT
PARTS
LISTCode
Ref. No.
Ref. No.
No.
★
Description
10.PartLISTE
DES
PIECES
Code
PARTS REPLACEMENT
CHANGE DES PIECES
Many electrical and mechanical parts in video cassette recorder have
special safety-related characteristics. These characteristics are often
not evident from visual inspection nor can the protection afforded by
them necessarily be obtained by using replacement components rated
for higher voltage, wattage, etc. Replacement parts which have these
special safety characteristics are identified in this manual; electrical
components having such features are identified by " å " and shaded
areas in the Replacement Parts Lists and Schematic Diagrams.
The use of a substitute replacement part which does not have the same
safety characteristics as the factory recommended replacement parts
shown in this service manual may create shock, fire or other hazards.
De nombreuses pièces électriques et mécaniques de magnétoscopes présentent des caractéristiques particulières de sécurité.
Ces caractéristiques ne sont pas toujours évidentes à l’inspection
visuelle et la protection qu’elles assurent ne peut pas toujours être
obtenue par des pièces de rechange étalonnées à un régime de
tension, une puissance, etc. superieurs. Les pièces de rechange qui
présentent ces caractéristiques spéciales de sécurité, sont identifiées
dans ce manuel: les pièces électriques qui présentent ces particularités,
sont repérée par la marque " å " et sont hachurées dans les listes de
pièces et dans les diagrammes schématiques.
La substitution d’une pièce de rechange par une autre qui ne présente
pas les mêmes caractéristiques de sécurité que la pièce recommandée
par l’usine et repérée dans ce manuel de service, peut provoquer une
électrocution, un incendie ou tout autre sinistre.
"HOW TO ORDER REPLACEMENT PARTS"
To have your order filled promptly and correctly, please furnish
the following informations.
1. MODEL NUMBER
2. REF. NO.
3. PART NO.
4. DESCRIPTION
in USA :
"COMMENT COMMANDER LES PIECES DE RECHANGE"
Pour que votre commande soit rapidement et correctement remplie,
veuillez fournir les renseignements suivants.
Contact your nearest SHARP Parts Distributor to order.
For location of SHARP Parts Distributor,
Please Call Toll-free;
1-800-BE-SHARP
1. NUMERO DU MODELE
3. NO. DE PIECE
In CANADA: Contact Sharp Electronics of Canada Limited
Phone (416) 890-2100
HOW TO IDENTIFY CHIP
TRANSISTORS AND
DIODES BY ITS MARKING
(3)
Marking
(2)
★MARQUE: SECTION LIVRAISON DES PIECES DE RECHANGE
Ref. No.
(1) Base/Input
(2) Emitter/Ground
(3) Collector/Output
(1)
2. NO. DE REF
4. DESCRIPTION
★
Part No.
Description
Code
DUNTK5845TEV8(VC-H810U)
DUNTK5845TEVE(VC-A410U)
MAIN UNIT
TUNER
Fig. 1
Package
Fig. 1
Fig. 1
Fig. 1
Fig. 1
Fig. 1
Fig. 1
Marking
TR/TS
LE/LF
PC
PD
NC
ND/NE
Parts No.
VS2SA1530ARS1
VS2AC3052EF-1
VSKRA103S//-1
VSKRA104S//-1
VSKRC103S//-1
VS2SD1306-E1E
Part No.
★
Description
- Main Unit(VC-H810U)
- Main Unit(VC-A410U)
- Operation Unit
IC201
VHiHA8317NF-1
IC601
VHiBA7755A/-1
IC651
VHiAN3662FB-1
IC701
IC702
IC706
RH-iX1566GEZZ
VHiPST600H/-1
VHiLB1988//-1
IC903
VHiKiA431//-1
Q251
Q302
Q306
Q501
Q602
VS2SA1530ARS1
VS2SD1306-E1E
VS2SA1530ARS1
VS2SC3052EF-1
VS2SD1859TV-1
or
VS2SC3939SQR-1
VS2SC3052EF-1
VS2SD1306-E1E
VS2SD1306-E1E
VSKRA104S//-1
VSKRC103S//-1
VSKRC103S//-1
V Tuner
BE
V HA118317NF, Y/C Audio AZ
Processor
V BA7755A, Rec/PB Head
AE
SW
V AN3662FBP, HiFi Audio
AZ
Processor(VC-H810U)
J IX1566GE
AY
V IC-PST600H-2
AE
V LB1988, Loading/Drum M AQ
Driver IC
V KIA431
AE
Code
TRANSISTORS
PRINTED WIRING BOARD ASSEMBLIES
(NOT REPLACEMENT ITEM)
DUNTK5845TEV8
DUNTK5845TEVE
DUNTK5846TEV1
RTUNQ0001AJZZ
INTEGRATED CIRCUITS
MARK★: SPARE PARTS-DELIVERY SECTION
Ref. No.
TU101
—
—
—
Q602
Q603
Q651
Q652
Q653
Q654
Q656
73
V
V
V
V
V
2SA1530ARS1
2SD1306-E
2SA1530ARS1
2SC3052EF(VC-H810U)
2SD1859TV
AC
AD
AC
AC
AD
V
V
V
V
V
V
V
SC3939SQR
2SC3052EF
2SD1306-E(VC-H810U)
2SD1306-E(VC-H810U)
KRA104S(VC-H810U)
KRC103S(VC-H810U)
KRC103S(VC-H810U)
AC
AC
AD
AD
AA
AA
AA
VC-A410U
VC-H810U
Ref. No.
Part No.
Q704
Q705
Q706
Q710
Q711
Q861
Q863
Q864
Q865
Q866
å Q901
å Q902
Q951
Q952
Q963
Q981
Q982
Q991
Q992
Q993
VS2SA1530ARS1
VS2SC3052EF-1
VS2SA1530ARS1
VS2SC3052EF-1
VS2SC3052EF-1
VSKRA103S//-1
VS2SC3052EF-1
VS2SC3052EF-1
VS2SC3052EF-1
VS2SC3052EF-1
VS2SC4161//1E
VS2SC3576AC-1
VS2SA1271-Y-1
VSKRC103S//-1
VS2SA1530ARS1
VS2SA1271-Y-1
VSKRC103S//-1
VS2SC3203Y/-1
VS2SA1530ARS1
VSKRC103S//-1
D351
VHD1SS119//-1
or
RH-DX0475CEZZ
RH-PX0270GEZZ
VHD1SS119//-1
or
RH-DX0475CEZZ
RH-PX0252GEZZ
RH-PX0252GEZZ
RH-PX0238GEZZ
RH-PX0238GEZZ
VHD1SS119//-1
or
RH-DX0475CEZZ
VHD1SS119//-1
or
RH-DX0475CEZZ
VHD1SS119//-1
or
RH-DX0475CEZZ
RH-PX0300GEZZ
RH-PX0300GEZZ
RH-PX0300GEZZ
RH-PX0300GEZZ
RH-PX0300GEZZ
VHDRL1N4004-1
VHDRL1N4004-1
VHDRL1N4004-1
VHDRL1N4004-1
VHD10ELS4//-1
VHD1SS119//-1
or
RH-DX0475CEZZ
RH-EX0601GEZZ
VHD1SS119//-1
or
RH-DX0475CEZZ
VHD10ELS4//-1
VHD15DF1FC/1E
or
VHDRU2YX+++-X
VHDD1NS4///-1
RH-EX0677GEZZ
RH-EX0631GEZZ
VHD1SS119//-1
or
RH-DX0475CEZZ
RH-FX0034CEZZ
or
RH-FX0002GEZZ
RH-PX0233GEZZ
RH-PX0233GEZZ
★
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
Description
2SA1530ARS1
2SC3052EF
2SA1530ARS1
SC3052EF
2SC3052EF
KRA103S
2SC3052EF
2SC3052EF
2SC3052EF
2SC3052EF
2SC4161
2SC3576AC
2SA1271-Y
KRC103S
2SA1530ARS1
2SA1271-Y
KRC103S
2SC3203Y
2SA1530ARS1
KRC103S
Code
AC
AC
AC
AC
AC
AA
AC
AC
AC
AC
AL
AC
AB
AA
AC
AB
AA
AB
AC
AA
DIODES AND LED’S
D351
D701
D702
D702
D706
D707
D708
D709
D712
D712
D715
D715
D716
å
å
å
å
å
å
D716
D861
D862
D863
D864
D865
D901
D902
D903
D904
D905
D907
å D907
å D912
å D913
å D913
å D921
å D923
å D923
å D928
D951
D991
D992
D992
å IC901
å IC901
Q701
Q702
Ref. No.
AB
V DX0475CE(VC-H810U)
J LED, Cassette LED
V 1SS119
AB
AC
AB
V
J
J
J
J
V
X501
X701
AB
AF
AF
AF
AF
AB
V DX0475CE
V 1SS119
AB
AB
V DX0475CE
V 1SS119
AB
AB
V
J
J
J
J
J
V
V
V
V
V
V
AB
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AB
DX0475CE
LED, Power
LED, Timer
LED, VCR
LED, Rec
LED, Tamper Proof
RL1N4004
RL1N4004
RL1N4004
RL1N4004
10ELS4
1SS119
V DX0475CE
J Zener Diode
V 1SS119
AB
AA
AB
V DX0475CE
V 10ELS4
V 15DF1FC
AB
AD
AD
V
V
J
J
V
AD
AE
AB
AA
AB
RU2YX
D1NS4
Zener Diode
Zener Diode
1SS119
V DX0475CE
V PC817
AB
AE
J PC817
J LED, Start Sensor
J LED, End Sensor
AD
AD
AD
Code
RR-DZ0047CEZZ
RCRSB0265GEZZ
or
RCRSB0204GEZZ
RCRSB0205GEZZ
V 2.7M Resistor
J Crystal, CRSB0265GE
AD
AH
J Crystal, CRSB0204GE
J Crystal, CRSB0205GE
AG
AM
COILS
L101
L201
L301
L301
L351
L351
L503
L602
å L901
å L901
DX0475CE
LED, Supply Reel Sensor
LED, Takeup Reel Sensor
LED, Cam SW A
LED, Cam SW B
1SS119
Description
PACKAGED CIRCUITS
å R901
X501
å L901
V 1SS119(VC-H810U)
★
Part No.
å L901
å L921
å L921
å L922
å L922
VP-CF101K0000
VP-XF820K0000
VP-2K101K0000
or
VP-MK101K0000
VP-2K101K0000
or
VP-MK101K0000
VP-XF120K0000
VP-DF221K0000
RCiLF0312GEZZ
or
RCiLF0014AJZZ
or
RCiLF0002AJZZ
or
RCiLF0005AJZZ
RCiLP0147GEZZ
or
RCiLP0161CEZZ
RCiLP0147GEZZ
or
RCiLP0161CEZZ
V Peaking, 100µH
V Peaking, 82µH
V Peaking, 100µH
AB
AB
AC
V Peaking, 100µH
V Peaking, 100µH
(VC-H810U)
V Peaking, 100µH
(VC-H810U)
V Peaking, 12µH
V Peaking, 220µH
J Coil, CiLF0312GE
AB
AC
V Coil, CiLF0014AJ
AG
V Coil, CiLF0002AJ
AK
V Coil, CiLF0005AJ
J Coil, CiLP0147GE, 10µH
AE
AC
V Coil, CiLP0161CE, 10µH
J Coil, CiLP0147GE
AD
AC
V Coil, CiLP0161CE, 10µH
AD
AB
AB
AB
AE
TRANSFORMERS
T601
å T901
RTRNH0098GEZZ
or
RTRNH0086GEZZ
RTRNZ0048AJZZ
or
RTRNZ0047AJZZ
R701
RVR-M4343GEZZ
C101
C102
VCKYCY1HB221K V 220p 50V Ceramic
VCCCCY1HH101J V 100p 50V Ceramic
(VC-A410U)
VCEA9M0JW107M V 100 6.3V Electrolytic
VCEA0A0JW108M V 1000 6.3V Electrolytic
VCKYCY1HF103Z V 0.01 50V Ceramic
VCEA9M0JW107M V 100 6.3V Electrolytic
(VC-H810U)
VCKYCY0JF105Z V 1
6.3V Ceramic
(VC-H810U)
VCEA9M1HW335M V 3.3
50V Electrolytic
(VC-H810U)
VCKYCY1HF103Z V 0.01 50V Ceramic
(VC-H810U)
VCEA9M1HW225M V 2.2
50V Electrolytic
(VC-H810U)
VCKYCY1CB104K V 0.1
16V Ceramic
(VC-H810U)
VCKYCY1CB473K V 0.047 16V Ceramic
(VC-H810U)
VCEA9M1HW474M V 0.47 50V Electrolytic
(VC-H810U)
VCKYCY1CB104K V 0.1
16V Ceramic
(VC-H810U)
VCKYCY1CB104K V 0.1
16V Ceramic
(VC-H810U)
VCKYCY1CB273K V 0.027 16V Ceramic
(VC-H810U)
T601
å T901
J OSC. Transformer
AE
J OSC. Transformer
V Transformer
AD
AQ
V Transformer
AV
VARIABLE RESISTOR
J Variable Resistor, 100k
PG MM
AB
CAPACITORS
C103
C105
C106
C142
C143
C145
C148
C160
C161
C162
C163
C164
C165
C166
74
AA
AA
AB
AC
AA
AB
AB
AB
AA
AB
AB
AA
AB
AB
AB
AA
VC-A410U
VC-H810U
Ref. No.
C167
C168
C169
C170
C201
C202
C203
C204
C205
C206
C207
C208
C209
C210
C211
C212
C213
C214
C215
C217
C218
C219
C220
C221
C223
C226
C227
C228
C251
C252
C254
C256
C301
C302
C303
C304
C305
C306
C307
C308
C309
C310
C311
C312
C319
C320
C327
C329
C351
C352
C353
C354
C356
C357
C358
C501
C502
C503
C504
C505
C506
C507
C508
C509
Part No.
★
Description
VCKYCY1CB104K V 0.1
16V Ceramic
(VC-H810U)
VCEA9M1CW106M V 10
16V Electrolytic
(VC-H810U)
VCEA9M1HW105M V 1
50V Electrolytic
(VC-H810U)
VCFYFA1HA124J V 0.12 50V M.polypro
(VC-H810U)
VCEA9M0JW107M V 100 6.3V Electrolytic
VCKYCY0JF105Z V 1
6.3V Ceramic
VCCCCY1HH151J V 150p 50V Ceramic
VCKYCY1CF104Z V 0.1
16V Ceramic
VCCCCY1HH470J V 47p 50V Ceramic
VCKYCY1CF104Z V 0.1
16V Ceramic
VCKYCY1CF104Z V 0.1
16V Ceramic
VCEA9M1CW106M V 10
16V Electrolytic
VCKYCY1CF104Z V 0.1
16V Ceramic
VCKYCY1CF104Z V 0.1
16V Ceramic
VCEA9M1HW335M V 3.3
50V Electrolytic
VCEA9M1CW106M V 10
16V Electrolytic
VCEA9M1HW225M V 2.2
50V Electrolytic
VCKYCY0JF105Z V 1
6.3V Ceramic
VCKYCY0JF105Z V 1
6.3V Ceramic
VCEA9M0JW107M V 100 6.3V Electrolytic
VCKYCY0JF105Z V 1
6.3V Ceramic
VCKYCY1CF104Z V 0.1
16V Ceramic
VCKYCY1CF104Z V 0.1
16V Ceramic
VCEA9M1CW106M V 10
16V Electrolytic
VCKYCY1CF104Z V 0.1
16V Ceramic
VCEA9M0JW107M V 100 6.3V Electrolytic
VCKYCY0JF105Z V 1
6.3V Ceramic
VCEA9M0JW107M V 100 6.3V Electrolytic
VCEA9M1CW476M V 47
16V Electrolytic
VCEA0A0JW337M V 330 6.3V Electrolytic
VCCCCY1HH330J V 33p 50V Ceramic
VCKYCY1CF104Z V 0.1
16V Ceramic
VCEA9M0JW107M V 100 6.3V Electrolytic
VCKYCY0JF105Z V 1
6.3V Ceramic
VCKYCY1HB102K V 1000p 50V Ceramic
VCKYCY1HB102K V 1000p 50V Ceramic
VCKYCY1HB102K V 1000p 50V Ceramic
VCKYCY1HB102K V 1000p 50V Ceramic
VCKYCY1HB102K V 1000p 50V Ceramic
VCKYCY1HB102K V 1000p 50V Ceramic
VCKYCY1HB102K V 1000p 50V Ceramic
VCKYCY1HB102K V 1000p 50V Ceramic
VCKYCY1HF103Z V 0.01 50V Ceramic
VCKYCY1HF103Z V 0.01 50V Ceramic
VCCCCY1HH100D V 10p 50V Ceramic
VCCCCY1HH100D V 10p 50V Ceramic
VCKYCY1HB102K V 1000p 50V Ceramic
VCKYCY1HF103Z V 0.01 50V Ceramic
VCEA9M0JW107M V 100 6.3V Electrolytic
(VC-H810U)
VCKYCY0JF105Z V 1
6.3V Ceramic
(VC-H810U)
VCKYCY1HF103Z V 0.01 50V Ceramic
(VC-H810U)
VCKYCY1HF103Z V 0.01 50V Ceramic
(VC-H810U)
VCCCCY1HH101J V 100p 50V Ceramic
(VC-H810U)
VCKYCY1CB104K V 0.1
16V Ceramic
(VC-H810U)
VCKYCY1CB104K V 0.1
16V Ceramic
(VC-H810U)
VCEA9M0JW107M V 100 6.3V Electrolytic
VCKYCY0JF105Z V 1
6.3V Ceramic
VCKYCY1HB472K V 4700p 50V Ceramic
VCEA9M1HW225M V 2.2
50V Electrolytic
VCKYCY1EB223K V 0.022 25V Ceramic
VCEA9M1HW474M V 0.47 50V Electrolytic
VCKYCY1CF104Z V 0.1
16V Ceramic
VCEA9M1HW475M V 4.7
50V Electrolytic
VCKYCY1HF103Z V 0.01 50V Ceramic
Code
Ref. No.
Part No.
★
AB
C512
C513
C514
C515
C517
C518
C521
C523
C524
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1HB331K
VCEA9M1HW335M
VCKYCY1HF333Z
VCCCCY1HH5R0C
VCKYCY1HF103Z
VCKYCY1HF103Z
V
V
V
V
V
V
V
V
V
C601
C602
C603
C604
C605
C606
C607
C608
C609
C610
VCEA9M0JW107M
VCKYCY1EB103K
VCEA9M1CW106M
VCKYCY1HB821K
VCEA9M1CW106M
VCEA9M1HW475M
VCEA9M1HW475M
VCEA9M0JW226M
VCEA9M1HW475M
VCKYCY1CF104Z
V
V
V
V
V
V
V
V
V
V
C611
C613
VCKYCY1CF104Z V
VCKYCY1EB183K V
C614
C617
C618
C619
C620
C621
C622
C630
C651
VCKYCY1HB222K
VCEA9M1CW476M
VCKYCY1EB103K
VCKYCY1EB103K
VCEA9M1CW106M
VCQPYA2AA562J
VCKYCY1HB222K
VCKYCY0JF105Z
VCEA9M1HW475M
C652
VCEA9M0JW336M V
C653
VCEA9M1CW106M V
C654
VCEA9M1CW106M V
C655
VCEA9M1CW106M V
C657
VCKYCY1EB153K V
C661
VCEA9M1HW475M V
C662
VCEA9M0JW336M V
C663
VCEA9M1CW106M V
C664
VCEA9M1CW106M V
C665
VCEA9M1CW106M V
AB
C667
VCKYCY1EB153K V
AA
C670
VCEA9M0JW107M V
AA
C671
VCEA9M1CW107M V
AA
C672
VCKYCY1CF224Z
AB
C673
VCEA9M0JW226M V
AB
C674
VCKYCY1CF224Z
V
AB
AB
AA
AB
AA
AB
AA
AB
AA
C675
VCKYCY1CF104Z
V
C677
VCEA9M1CW106M V
C678
VCKYCY1HF103Z
V
C679
VCKYCY1CF224Z
V
AB
AB
AC
AB
AB
AA
AA
AA
AA
AA
AB
AA
AA
AB
AB
AB
AB
AB
AB
AB
AA
AA
AB
AA
AB
AB
AB
AB
AC
AA
AA
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
75
V
V
V
V
V
V
V
V
V
V
Description
0.01 50V Ceramic
0.01 50V Ceramic
0.01 50V Ceramic
330p 50V Ceramic
3.3
50V Electrolytic
0.033 50V Ceramic
5p
50V Ceramic
0.01 50V Ceramic
0.01 50V Ceramic
(VC-H810U)
100 6.3V Electrolytic
0.01 25V Ceramic
10
16V Electrolytic
820p 50V Ceramic
10
16V Electrolytic
4.7
50V Electrolytic
4.7
50V Electrolytic
22
6.3V Electrolytic
4.7
50V Electrolytic
0.1
16V Ceramic
(VC-A410U)
0.1
16V Ceramic
0.018 25V Ceramic
(VC-A410U)
2200p 50V Ceramic
47
16V Electrolytic
0.01 25V Ceramic
0.01 25V Ceramic
10
16V Electrolytic
5600p 100V Mylar
2200p 50V Ceramic
1
6.3V Ceramic
4.7
50V Electrolytic
(VC-H810U)
33
6.3V Electrolytic
(VC-H810U)
10
16V Electrolytic
(VC-H810U)
10
16V Electrolytic
(VC-H810U)
10
16V Electrolytic
(VC-H810U)
0.015 25V Ceramic
(VC-H810U)
4.7
50V Electrolytic
(VC-H810U)
33
6.3V Electrolytic
(VC-H810U)
10
16V Electrolytic
(VC-H810U)
10
16V Electrolytic
(VC-H810U)
10
16V Electrolytic
(VC-H810U)
0.015 25V Ceramic
(VC-H810U)
100 6.3V Electrolytic
(VC-H810U)
100 16V Electrolytic
(VC-H810U)
0.22 16V Ceramic
(VC-H810U)
22
6.3V Electrolytic
(VC-H810U)
0.22 16V Ceramic
(VC-H810U)
0.1
16V Ceramic
(VC-H810U)
10
16V Electrolytic
(VC-H810U)
0.01 50V Ceramic
(VC-H810U)
0.22 16V Ceramic
(VC-H810U)
Code
AA
AA
AA
AA
AB
AA
AA
AA
AA
AB
AA
AB
AA
AB
AB
AB
AB
AB
AA
AA
AA
AA
AB
AA
AA
AB
AC
AA
AB
AB
AB
AB
AB
AB
AA
AB
AB
AB
AB
AB
AA
AB
AB
AA
AB
AA
AA
AB
AA
AA
VC-A410U
VC-H810U
Ref. No.
Part No.
C680
VCKYCY0JF105Z
C681
VCKYCY1HF103Z
C682
VCKYCY0JF105Z
C684
VCCCCY1HH560J
C685
VCCCCY1HH560J
C701
C702
C703
C704
C705
C706
C707
C708
C711
C712
C713
C714
C715
C717
C718
C719
C722
C723
C724
C726
VCKYCY1HF103Z
VCKYCY1HF103Z
VCEA9M1HW105M
VCKYCY0JF105Z
VCKYCY1HF103Z
VCKYCY1HF103Z
VCCCCY1HH120J
VCCCCY1HH150J
VCKYCY1HB102K
VCKYCY1HB102K
VCKYCY1HB102K
VCKYCY1CF104Z
VCEA9M0JW226M
VCKYCY1HB221K
VCKYCY1CF104Z
VCKYCY1EB103K
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1HF103Z
C727
C729
C730
C736
C737
C738
C739
C743
C744
C747
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1HB102K
VCKYCY1HB102K
VCKYCY0JF105Z
VCEA2A0JW477M
VCKYCY1HF103Z
C748
C750
C751
C754
C755
C756
C759
C760
C763
C764
C770
C771
C774
C775
C776
C783
C784
C785
C786
C787
C789
C790
C791
C792
C794
C795
C797
C798
C804
å C901
å C901
★
Description
V 1
6.3V Ceramic
(VC-H810U)
V 0.01 50V Ceramic
(VC-H810U)
V 1
6.3V Ceramic
(VC-H810U)
V 56p 50V Ceramic
(VC-H810U)
V 56p 50V Ceramic
(VC-H810U)
V 0.01 50V Ceramic
V 0.01 50V Ceramic
V 1
50V Electrolytic
V 1
6.3V Ceramic
V 0.01 50V Ceramic
V 0.01 50V Ceramic
V 12p 50V Ceramic
V 15p 50V Ceramic
V 1000p 50V Ceramic
V 1000p 50V Ceramic
V 1000p 50V Ceramic
V 0.1
16V Ceramic
V 22
6.3V Electrolytic
V 220p 50V Ceramic
V 0.1
16V Ceramic
V 0.01 25V Ceramic
V 0.01 50V Ceramic
V 0.01 50V Ceramic
V 0.01 50V Ceramic
V 0.01 50V Ceramic
(VC-H810U)
V 0.01 50V Ceramic
V 0.01 50V Ceramic
V 0.01 50V Ceramic
V 0.01 50V Ceramic
V 0.01 50V Ceramic
V 1000p 50V Ceramic
V 1000p 50V Ceramic
V 1
6.3V Ceramic
V 470 6.3V Electrolytic
V 0.01 50V Ceramic
(VC-H810U)
V 0.01 50V Ceramic
V 0.01 50V Ceramic
V 0.01 50V Ceramic
V 0.01 25V Ceramic
V 0.047 50V Ceramic
V 0.047 50V Ceramic
V 22
6.3V Electrolytic
V 100 6.3V Electrolytic
V 47
6.3V Electrolytic
V 0.01 50V Ceramic
V 100p 50V Ceramic
V 1
50V Electrolytic
V 0.1
16V Ceramic
V 100 6.3V Electrolytic
V 1
6.3V Ceramic
V 1
6.3V Ceramic
V 1000p 50V Ceramic
V 47
6.3V Electrolytic
V 0.33 16V Ceramic
V 0.47 50V
V 0.01 25V Ceramic
V 3900p 50V Ceramic
V 3900p 50V Ceramic
V 47
16V Electrolytic
V 0.022 25V Ceramic
V 0.022 25V Ceramic
V 0.1
16V Ceramic
V 0.022 25V Ceramic
V 47
6.3V Electrolytic
V 0.01 AC250V M.Polypro
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1EB103K
VCKYCY1HF473Z
VCKYCY1HF473Z
VCEA9M0JW226M
VCEA9M0JW107M
VCEA9M0JW476M
VCKYCY1HF103Z
VCCCCY1HH101J
VCE9EM1HW105M
VCKYCY1CF104Z
VCEA9M0JW107M
VCKYCY0JF105Z
VCKYCY0JF105Z
VCKYCY1HB102K
VCEA9M0JW476M
VCKYCY1CF334Z
VCFYFA1HA474J
VCKYCY1EB103K
VCKYCY1HB392K
VCKYCY1HB392K
VCEA9M1CW476M
VCKYCY1EB223K
VCKYCY1EB223K
VCKYCY1CF104Z
VCKYCY1EB223K
VCEA9M0JW476M
RC-FZ023CUMZZ
or
RC-QZ001DGEZZ J 0.01 AC250V Mylar
Code
Ref. No.
AB
å C903
AA
å
å
å
å
å
å
å
å
å
å
å
å
å
★
Part No.
C903
C906
C907
C908
C910
C911
C915
C916
C921
C923
C925
C928
C929
C932
C933
C941
C942
C951
C953
C954
C971
C981
C985
C991
RC-KZ0147GEZZ
or
RC-KZ0092GEZZ
RC-EZ0238CEZZ
RC-KZ0029CEZZ
VCKYPA2HB221K
VCKYCY1HB332K
VCQYTA1HM472K
VCKYCY1HB221K
VCKYCY1HF333Z
VCEA0A2AW106M
VCEA0A1VW477M
VCEA0A0JW108M
VCEA0A1CW337M
VCEA0A0JW108M
VCQYTA1HM104J
VCQYTA1HM104J
VCEA9A1CW476M
VCEA9M0JW476M
VCKYCY1HF333Z
VCEA9M1CW106M
VCEA9M1HW105M
VCEA9M0JW226M
VCEA9M0JW476M
VCEA9M0JW476M
VCEA9M1CW476M
RJ101
RJ102
VRS-CY1JF000J
VRS-CY1JF000J
AA
AA
AA
AA
AA
AA
AA
AB
AB
AA
RJ103
VRS-CY1JF000J
RJ301
RJ302
RJ303
RJ304
RJ305
RJ501
RJ502
R36
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
AA
AA
AA
AA
AA
AA
AB
AB
AB
AA
AA
AB
AA
AB
AB
AB
AA
AB
AA
AC
AA
AA
AA
AB
AA
AA
AA
AA
AB
AF
R101
R103
R104
R105
R107
VRS-CY1JF470J
VRS-CY1JF473J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF822J
R108
VRS-CY1JF822J
R111
R112
R145
VRS-CY1JF153J
VRS-CY1JF153J
VRS-CY1JF000J
R201
R202
R203
R207
R211
R212
R225
R226
R227
R252
R253
R254
R256
R301
R313
R315
R330
R331
R351
VRS-CY1JF682J
VRS-CY1JF182J
VRS-CY1JF682J
VRS-CY1JF101J
VRS-CY1JF153J
VRS-CY1JF153J
VRS-CY1JF750J
VRS-CY1JF101J
VRS-CY1JF750J
VRD-RA2EE331J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF183J
VRS-CY1JF473J
VRS-CY1JF332J
VRS-CY1JF152J
VRS-CY1JF222J
VRS-CY1JF102J
VRS-CY1JF102J
R501
VRS-CY1JF681J
AB
AA
AA
AA
AA
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
Description
Code
J 3300p AC125V Ceramic
AC
J
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
AC
AE
AC
AA
AA
AB
AA
AA
AC
AB
AC
AC
AC
AA
AA
AB
AB
AA
AB
AB
AB
AB
AB
AB
3300p AC125V Ceramic
82
200V Electrolytic
0.01 500V Ceramic
220p 500V Ceramic
3300p 50V Ceramic
4700p 50V Mylar
220p 50V Ceramic
0.033 50V Ceramic
10
100V Electrolytic
470 35V Electrolytic
1000 6.3V Electrolytic
330 16V Electrolytic
1000 6.3V Electrolytic
0.1
50V Mylar
0.1
50V Mylar
47
16V Electrolytic
47
6.3V Electrolytic
0.033 50V Ceramic
10
16V Electrolytic
1
50V Electrolytic
22
6.3V Electrolytic
47
6.3V Electrolytic
47
6.3V Electrolytic
47
16V Electrolytic
RESISTORS
AF
76
V 0
1/16W
V 0
1/16W
(VC-H810U)
V 0
1/16W
(VC-A410U)
V 0
1/16W
V 0
1/16W
V 0
1/16W
V 0
1/16W
V 0
1/16W
V 0
1/16W
V 0
1/16W
V 0
1/16W
(VC-H810U)
V 47
1/16W
V 47k 1/16W
V 0
1/16W
V 0
1/16W
V 8.2k 1/16W
(VC-H810U)
V 8.2k 1/16W
(VC-A410U)
V 15k 1/16W
V 15k 1/16W
V 0
1/16W
(VC-H810U)
V 6.8k 1/16W
V 1.8k 1/16W
V 6.8k 1/16W
V 100 1/16W
V 15k 1/16W
V 15k 1/16W
V 75
1/16W
V 100 1/16W
V 75
1/16W
V 330 1/4W
V 100 1/16W
V 100 1/16W
V 18k 1/16W
V 47k 1/16W
V 3.3k 1/16W
V 1.5k 1/16W
V 2.2k 1/16W
V 1k
1/16W
V 1k
1/16W
(VC-H810U)
V 680 1/16W
Metal Oxide
Metal Oxide
AA
AA
Metal Oxide
AA
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
AA
AA
AA
AA
AA
AA
AA
AA
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
AA
AA
AA
AA
AA
Metal Oxide
AA
Metal Oxide
Metal Oxide
Metal Oxide
AA
AA
AA
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
Metal Oxide
AA
VC-A410U
VC-H810U
Ref. No.
Part No.
R502
R505
R511
VRS-CY1JF273J
VRS-CY1JF000J
VRS-CY1JF272J
R512
VRS-CY1JF272J
R520
VRS-CY1JF154J
R521
VRS-CY1JF473J
R601
R602
R603
R604
R605
R606
R607
R608
R609
VRS-CY1JF822J
VRS-CY1JF274J
VRS-CY1JF221J
VRS-CY1JF473J
VRS-CY1JF153J
VRS-CY1JF273J
VRS-CY1JF561J
VRS-CY1JF472J
VRS-CY1JF333J
R610
VRS-CY1JF183J
R611
VRS-CY1JF153J
R611
VRS-CY1JF393J
R612
VRS-CY1JF123J
R612
VRS-CY1JF823J
R615
VRS-CY1JF472J
R616
VRS-CY1JF103J
R617
VRS-CY1JF103J
R618
R619
R620
R621
R623
R624
R626
R627
R628
VRS-CY1JF563J
VRS-CY1JF470J
VRS-CY1JF153J
VRD-RA2EE4R7J
VRS-CY1JF393J
VRS-CY1JF224J
VRS-CY1JF000J
VRS-CY1JF332J
VRS-CY1JF000J
R653
VRS-CY1JF473J
R654
VRS-CY1JF682J
R657
VRS-CY1JF101J
R658
VRS-CY1JF223J
R659
VRD-RA2BE681J
R663
VRS-CY1JF473J
R664
VRS-CY1JF682J
R667
VRD-RA2BE101J
R668
VRS-CY1JF223J
R669
VRD-RA2BE681J
R670
VRS-CY1JF273J
R671
VRS-CY1JF103J
R672
VRS-CY1JF151J
R673
VRS-CY1JF151J
★
Description
V 27k 1/16W
V 0
1/16W
V 2.7k 1/16W
(VC-H810U)
V 2.7k 1/16W
(VC-H810U)
V 150k 1/16W
(VC-H810U)
V 47k 1/16W
(VC-H810U)
V 8.2k 1/16W
V 270k 1/16W
V 220 1/16W
V 47k 1/16W
V 15k 1/16W
V 27k 1/16W
V 560 1/16W
V 4.7k 1/16W
V 33k 1/16W
(VC-A410U)
V 18k 1/16W
(VC-A410U)
V 15k 1/16W
(VC-H810U)
V 39k 1/16W
(VC-A410U)
V 12k 1/16W
(VC-A410U)
V 82k 1/16W
(VC-H810U)
V 4.7k 1/16W
(VC-A410U)
V 10k 1/16W
(VC-A410U)
V 10k 1/16W
(VC-H810U)
V 56k 1/16W
V 47
1/16W
V 15k 1/16W
V 4.7 1/4W
V 39k 1/16W
V 220k 1/16W
V 0
1/16W
V 3.3k 1/16W
V 0
1/16W
(VC-A410U)
V 47k 1/16W
(VC-H810U)
V 6.8k 1/16W
(VC-H810U)
V 100 1/16W
(VC-H810U)
V 22k 1/16W
(VC-H810U)
V 680 1/8W
(VC-H810U)
V 47k 1/16W
(VC-H810U)
V 6.8k 1/16W
(VC-H810U)
V 100 1/8W
(VC-H810U)
V 22k 1/16W
(VC-H810U)
V 680 1/8W
(VC-H810U)
V 27k 1/16W
(VC-H810U)
V 10k 1/16W
(VC-H810U)
V 150 1/16W
(VC-H810U)
V 150 1/16W
(VC-H810U)
Code
Ref. No.
Metal Oxide
Metal Oxide
Metal Oxide
AA
AA
AA
R674
VRS-CY1JF473J
R675
VRS-CY1JF183J
Metal Oxide
AA
R676
VRS-CY1JF102J
Metal Oxide
AA
R677
VRS-CY1JF473J
Metal Oxide
AA
R685
VRS-CY1JF102J
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
AA
AA
AA
AA
AA
AA
AA
AA
AA
R686
VRS-CY1JF102J
R690
VRS-CY1JF000J
R704
R706
R707
R708
R709
VRD-RA2BE223J
VRS-CY1JF153J
VRS-CY1JF153J
VRS-CY1JF102J
VRS-CY1JF102J
Metal Oxide
AA
Metal Oxide
AA
Metal Oxide
AA
Metal Oxide
AA
Metal Oxide
AA
R710
R711
R712
R714
R715
R716
R717
R718
R719
R720
VRS-CY1JF473J
VRS-CY1JF473J
VRS-CY1JF223J
VRS-CY1JF332J
VRS-CY1JF102J
VRS-CY1JF102J
VRS-CY1JF681J
VRS-CY1JF182J
VRD-RA2BE102J
VRS-CY1JF822J
Metal Oxide
AA
Metal Oxide
AA
R722
R723
R725
VRD-RA2BE102J
VRS-CY1JF000J
VRD-RA2BE103J
Metal Oxide
AA
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
AA
AA
AA
AA
AA
AA
AA
AA
AA
Metal Oxide
AA
Metal Oxide
AA
Metal Oxide
AA
Metal Oxide
AA
Carbon
AA
Metal Oxide
AA
Metal Oxide
AA
Carbon
AB
Metal Oxide
AA
Carbon
AA
Metal Oxide
AA
Metal Oxide
AA
Metal Oxide
AA
R726
R727
R728
R729
R731
R732
R734
R735
R736
R737
R738
R739
R740
R741
R742
R743
R744
R745
R746
R748
R750
R751
R752
R753
R754
R756
R760
R761
R762
R763
R764
R765
R766
R768
R769
R770
R772
VRS-CY1JF103J
VRD-RA2EE151J
VRS-CY1JF182J
VRD-RA2BE154J
VRS-CY1JF103J
VRS-CY1JF223J
VRD-RA2BE223J
VRS-CY1JF563J
VRS-CY1JF123J
VRS-CY1JF000J
VRD-RA2BE104J
VRD-RA2BE271J
VRD-RA2BE104J
VRD-RA2BE271J
VRS-CY1JF473J
VRD-RA2BE391J
VRS-CY1JF473J
VRD-RA2BE391J
VRS-CY1JF103J
VRS-CY1JF1R0J
VRS-CY1JF474J
VRD-RA2BE123J
VRD-RA2BE123J
VRD-RA2BE223J
VRS-CY1JF102J
VRS-CY1JF102J
VRS-CY1JF104J
VRS-CY1JF104J
VRS-CY1JF123J
VRS-CY1JF563J
VRS-CY1JF183J
VRS-CY1JF223J
VRS-CY1JF103J
VRS-CY1JF102J
VRS-CY1JF472J
VRS-CY1JF332J
VRS-CY1JF822J
Metal Oxide
AA
R773
VRS-CY1JF222J
77
Part No.
★
Description
V 47k 1/16W
(VC-H810U)
V 18k 1/16W
(VC-H810U)
V 1k
1/16W
(VC-H810U)
V 47k 1/16W
(VC-H810U)
V 1k
1/16W
(VC-H810U)
V 1k
1/16W
(VC-H810U)
V 0
1/16W
(VC-H810U)
V 22k 1/8W
V 15k 1/16W
V 15k 1/16W
V 1k
1/16W
V 1k
1/16W
(VC-H810U)
V 47k 1/16W
V 47k 1/16W
V 22k 1/16W
V 3.3k 1/16W
V 1k
1/16W
V 1k
1/16W
V 680 1/16W
V 1.8k 1/16W
V 1k
1/8W
V 8.2k 1/16W
(VC-A410U)
V 1k
1/8W
V 0
1/16W
V 10k 1/8W
(VC-A410U)
V 10k 1/16W
V 150 1/4W
V 1.8k 1/16W
V 150k 1/8W
V 10k 1/16W
V 22k 1/16W
V 22k 1/8W
V 56k 1/16W
V 12k 1/16W
V 0
1/16W
V 100k 1/8W
V 270 1/8W
V 100k 1/8W
V 270 1/8W
V 47k 1/16W
V 390 1/8W
V 47k 1/16W
V 390 1/8W
V 10k 1/16W
V 1
1/16W
V 470k 1/16W
V 12k 1/8W
V 12k 1/8W
V 22k 1/8W
V 1k
1/16W
V 1k
1/16W
V 100k 1/16W
V 100k 1/16W
V 12k 1/16W
V 56k 1/16W
V 18k 1/16W
V 22k 1/16W
V 10k 1/16W
V 1k
1/16W
V 4.7k 1/16W
V 3.3k 1/16W
V 8.2k 1/16W
(VC-A410U)
V 2.2k 1/16W
Code
Metal Oxide
AA
Metal Oxide
AA
Metal Oxide
AA
Metal Oxide
AA
Metal Oxide
AA
Metal Oxide
AA
Metal Oxide
AA
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
AA
AA
AA
AA
AA
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
Carbon
Metal Oxide
Carbon
AA
AA
AA
Metal Oxide
Carbon
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Carbon
Carbon
Carbon
Metal Oxide
Carbon
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Carbon
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
Metal Oxide
AA
VC-A410U
VC-H810U
Ref. No.
R774
R776
R777
R778
R779
R780
R781
R782
R783
R784
R785
R786
R787
R788
R789
R791
R792
R793
R794
R795
R796
R798
R813
R814
R815
R821
R822
R823
R824
R825
R826
R831
R832
R833
R841
R843
R845
R846
R847
R848
R856
å
å
å
å
å
å
R857
R858
R859
R860
R861
R863
R864
R865
R866
R867
R870
R904
R905
R910
R912
R917
R918
R923
R924
R930
R931
R932
R933
R934
R951
R954
R955
R957
R973
R974
R981
R982
Part No.
VRS-CY1JF102J
★
Description
V 1k
1/16W
(VC-H810U)
VRS-CY1JF681J
V 680 1/16W
VRS-CY1JF681J
V 680 1/16W
VRS-CY1JF104J
V 100k 1/16W
VRD-RA2BE103J V 10k 1/8W
VRD-RA2BE103J V 10k 1/8W
VRD-RA2BE103J V 10k 1/8W
VRS-CY1JF154J
V 150k 1/16W
VRS-CY1JF392J
V 3.9k 1/16W
VRS-CY1JF104J
V 100k 1/16W
VRS-CY1JF105J
V 1M 1/16W
VRS-CY1JF564J
V 560k 1/16W
VRD-RM2HD1R0J V 1
1/2W
VRD-RM2HD1R0J V 1
1/2W
VRS-CY1JF822J
V 8.2k 1/16W
VRS-CY1JF1R0J
V 1
1/16W
VRS-CY1JF473J
V 47k 1/16W
VRS-CY1JF154J
V 150k 1/16W
VRS-CY1JF332J
V 3.3k 1/16W
VRD-RA2BE105J V 1M 1/8W
VRD-RA2BE103J V 10k 1/8W
VRS-CY1JF102J
V 1k
1/16W
VRD-RA2BE183J V 18k 1/8W
VRS-CY1JF272J
V 2.7k 1/16W
VRD-RA2BE332J V 3.3k 1/8W
VRS-CY1JF183J
V 18k 1/16W
VRS-CY1JF272J
V 2.7k 1/16W
VRD-RA2BE332J V 3.3k 1/8W
VRS-CY1JF472J
V 4.7k 1/16W
VRS-CY1JF822J
V 8.2k 1/16W
VRS-CY1JF103J
V 10k 1/16W
VRD-RA2BE101J V 100 1/8W
VRS-CY1JF103J
V 10k 1/16W
VRS-CY1JF103J
V 10k 1/16W
VRD-RA2BE183J V 18k 1/8W
VRD-RA2BE474J V 470k 1/8W
VRD-RA2BE474J V 470k 1/8W
VRD-RA2BE103J V 10k 1/8W
VRD-RA2BE474J V 470k 1/8W
VRD-RA2BE474J V 470k 1/8W
VRD-RA2BE102J V 1k
1/8W
(VC-H810U)
VRS-CY1JF102J
V 1k
1/16W
VRS-CY1JF102J
V 1k
1/16W
VRD-RA2BE471J V 470 1/8W
VRS-CY1JF102J
V 1k
1/16W
VRD-RA2BE102J V 1k
1/8W
VRD-RA2BE102J V 1k
1/8W
VRD-RA2BE102J V 1k
1/8W
VRD-RA2BE102J V 1k
1/8W
VRD-RA2BE102J V 1k
1/8W
VRS-CY1JF223J
V 22k 1/16W
VRD-RA2BE223J V 22k 1/8W
VRS-VV3DB333J V 33k 2W
VRD-RM2HD154J V 150k 1/2W
VRD-RM2HD390J V 39
1/2W
VRD-RM2HD390J V 39
1/2W
VRS-CY1JF562J
V 5.6k 1/16W
VRS-CY1JF000J
V 0
1/16W
VRD-RA2BE102J V 1k
1/8W
VRS-CY1JF102J
V 1k
1/16W
VRD-RA2BE332J V 3.3k 1/8W
VRS-CY1JF102J
V 1k
1/16W
VRD-RA2BE101J V 100 1/8W
VRS-CY1JF102J
V 1k
1/16W
VRS-CY1JF102J
V 1k
1/16W
VRD-RM2HD152J V 1.5k 1/2W
VRS-CY1JF561J
V 560 1/16W
VRS-CY1JF103J
V 10k 1/16W
VRS-CY1JF472J
V 4.7k 1/16W
VRS-CY1JF103J
V 10k 1/16W
VRD-RA2BE222J V 2.2k 1/8W
VRS-CY1JF103J
V 10k 1/16W
VRS-CY1JF561J
V 560 1/16W
Code
Ref. No.
Metal Oxide
AA
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Carbon
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Carbon
Metal Oxide
Carbon
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
R983
R991
R992
R993
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Carbon
Carbon
Carbon
Carbon
Carbon
Metal Oxide
Carbon
Metal Oxide
Carbon
Carbon
Carbon
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Carbon
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
★
Part No.
VRS-CY1JF000J
VRS-CY1JF102J
VRS-CY1JF222J
VRS-CY1JF103J
V
V
V
V
Description
0
1k
2.2k
10k
1/16W
1/16W
1/16W
1/16W
Code
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
AA
AA
AA
AA
BALUNES
FB201
FB202
FB203
FB701
FB702
å FB901
RBLN-0036CEZZ
RBLN-0036CEZZ
RBLN-0036CEZZ
RBLN-0036CEZZ
RBLN-0036CEZZ
RBLN-0036CEZZ
V
V
V
V
V
V
Balun, BLN-0036CE
Balun, BLN-0036CE
Balun, BLN-0036CE
Balun, BLN-0036CE
Balun, BLN-0036CE
Balun, BLN-0036CE
AB
AB
AB
AB
AB
AB
SWITCHES
S101
S701
S801
S801
S802
S802
S803
S803
S804
S804
S805
S805
S806
S806
QSW-S0004AJZZ
QSW-F0042AJZZ
QSW-K0086GEZZ
or
QSW-K0004AJZZ
QSW-K0086GEZZ
or
QSW-K0004AJZZ
QSW-K0086GEZZ
or
QSW-K0004AJZZ
QSW-K0086GEZZ
or
QSW-K0004AJZZ
QSW-K0086GEZZ
or
QSW-K0004AJZZ
QSW-K0086GEZZ
or
QSW-K0004AJZZ
V Switch, RF Conv. SW
V Switch, Rec Tip SW
J Switch, Power
AF
AG
AC
V Switch, Power
J Switch, Eject
AB
AC
V Switch, Eject
J Switch, Set/S-Pic.
AB
AC
V Switch, Set/S-Pic.
J Switch, CH –
AB
AC
V Switch, CH –
J Switch, Menu
AB
AC
V Switch, Menu
J Switch, CH +
AB
AC
V Switch, CH +
AB
MISCELLANEOUS PARTS
PSLDM4575AJFW
QCNW-0307AJZZ
å ACC901 QACCD3049AJZZ
or
å ACC901 QACCD3048AJZZ
å FH901 QFSHD1013CEZZ
å FH902 QFSHD1014CEZZ
å F901
QFS-B3025CEZZ
or
å F901
QFS-A3025CEZZ
J201
QJAKL0006AJZZ
V H/A Shield bottom
V Connecting Cord
V AC Cord
AD
AD
AN
V
V
V
V
AN
AC
AC
AD
AC Cord
Fuse Holder
Fuse Holder
Fuse, 3.0A 125V
V Fuse, 3.0A 125V
V Jack, Rear AV Jack
(VC-H810U)
J201
QJAKH0011AJZZ V Jack, Rear AV Jack
or
(VC-A410U)
J201
QJAKH0013AJZZ V Jack, Rear AV Jack
(VC-A410U)
P701
QPLGZ0883GEZZ J Plug, 8 Pin
RMC801 RRMCU0081GEZZ J Remote Receiver
or
RMC801 RRMCU0002AJZZ V Remote Receiver
SC301 QSOCN0911REN1 V Socket, 9 Pin(VC-H810U)
SC301 QSOCN0611REN1 V Socket, 6 Pin(VC-A410U)
SC601 QSOCN0695REZZ V Socket, 6 Pin
SC602 QSOCZ0293GEZZ J Socket, 2 Pin
SC701 QSOCN0795REZZ V Socket, 7 Pin
SC702 QSOCZ0292GEZZ J Socket, 2 Pin
SC801 QSOCZ0625CEZZ V Socket, 6 Pin
TP201 QPLGN0447REZZ V Plug, 4 Pin
W851
LHLDZ1962AJ00
V Holder
W852
LHLDZ1962AJ00
V Holder
AD
AL
AK
AF
AD
AG
AH
AD
AC
AB
AC
AC
AC
AC
AA
AD
AD
DUNTK5846TEV1 OPERATION UNIT
RESISTORS
R882
R883
R884
78
VRS-CY1JF472J
VRS-CY1JF822J
VRS-CY1JF103J
V 4.7k 1/16W Metal Oxide
V 8.2k 1/16W Metal Oxide
V 10k 1/16W Metal Oxide
AA
AA
AA
VC-A410U
VC-H810U
Ref. No.
★
Part No.
R885
R886
R887
R888
R889
R897
R898
VRS-CY1JF223J
VRS-CY1JF103J
VRS-CY1JF473J
VRS-CY1JF123J
VRS-CY1JF563J
VRD-RA2BE563J
VRD-RA2BE223J
S882
QSW-K0086GEZZ
or
QSW-K0004AJZZ
QSW-K0086GEZZ
or
QSW-K0004AJZZ
QSW-K0086GEZZ
or
QSW-K0004AJZZ
QSW-K0086GEZZ
or
QSW-K0004AJZZ
QSW-K0086GEZZ
or
QSW-K0004AJZZ
QSW-K0086GEZZ
or
QSW-K0004AJZZ
V
V
V
V
V
V
V
Description
22k
10k
47k
12k
56k
56k
22k
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/8W
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Carbon
Code
AA
AA
AA
AA
AA
AA
AA
SWITCHES
S882
S883
S883
S884
S884
S885
S885
S886
S886
S887
S887
J Switch, Stop
AC
V Switch, Stop
J Switch, Rec
AB
AC
V Switch, Rec
J Switch, Pause/Still
AB
AC
V Switch, Pause/Still
J Switch, FF
AB
AC
V Switch, FF
J Switch, Play
AB
AC
V Switch, Play
J Switch, Rew
AB
AC
V Switch, Rew
AB
MISCELLANEOUS PART
P881
QPLGZ0626CEZZ
V Plug, 6 Pin
LBNDK1011AJZZ
LBOSZ1007AJZZ
LBOSZ1006AJZZ
LCHSM0174AJZZ
LHLDZ2016AJZZ
LPOLM0070GEZZ
LPOLM0064GEZZ
MLEVF0518AJZZ
V
V
V
V
V
J
J
V
10
MLEVF0519AJZZ
V
11
12
15
16
17
18
19
20
21
22
23
24
25
27
29
30
MLEVF0499AJZZ
MLEVF0500GEZZ
MLEVF0523AJZZ
LANGF9620AJFW
MLEVP0271AJZZ
MLEVP0272AJZZ
MLEVP0301AJZZ
MLEVP0275AJZZ
MLEVP0292AJZZ
MLEVP0290AJZZ
MLEVP0293AJZZ
MLEVP0324AJZZ
MLEVP0325AJZZ
MSLiP0010AJZZ
MSPRD0175AJFJ
MSPRT0402AJFJ
V
J
V
V
V
V
V
V
V
V
V
V
V
V
V
V
31
MSPRT0403AJFJ
V
32
33
34
35
36
37
38
39
40
MSPRC0213AJFJ
MSPRT0416AJFJ
NBLTK0067AJ00
NDAiV1078AJ00
NGERH1293AJZZ
NGERH1295AJ00
NGERH1294AJZZ
NGERH1270AJZZ
NGERH1271AJZZ
V
V
V
V
V
V
V
V
V
★
41
43
44
45
46
47
48
49
50
51
52
53
55
56
57
58
59
60
61
62
NGERH1272AJZZ
NGERH1299AJZZ
NGERW1070AJZZ
NGERW1066AJZZ
NiDR-0018AJZZ
NPLYV0162AJZZ
NPLYV0163AJZZ
NROLP0131GEZZ
NSFTP0032AJZZ
MSPRC0217AJFJ
PREFL1011AJZZ
QCNW-8022AJZZ
QCNW-8021AJZZ
QPWBF5243AJZZ
QSOCN0696REZZ
RHEDT0036AJZZ
RHEDU0088GEZZ
RMOTM1078GEZZ
RMOTN2067GEZZ
RMOTP1139GEZZ
V
V
V
V
V
V
V
J
V
V
V
V
V
V
V
V
J
J
J
J
62
RMOTP1151GEZZ J
63
DDRMW0029TEX1 V
63
DDRMW0030TEX1 V
65
66
QBRSK0041GEZZ J
XBPSD26P05J00 V
67
68
69
70
71
PGiDC0056GEFW J
QPWBF5468AJZZ V
QPLGZ0292GEZZ J
MSPRC0223AJFJ V
MSPRC0224AJFJ V
AF
MECHANISM CHASSIS PARTS
1
2
4
5
6
7
8
9
Part No.
Ref. No.
Tension Band Ass’y
AH
Tension Arm boss
AD
Cassette Stay L
AD
Main Chassis Ass’y
AV
Loading Motor Block
AG
Supply Pole Base Ass’y
AK
Take-up Pole Base Ass’y AM
Take-up Loading
AF
Arm Ass’y
Supply Loading
AF
Arm Ass’y
Pinch Drive Lever Ass’y
AG
Pinch Roller Lever Ass’y AW
Tension Arm Ass’y
AH
A/C Head Plate
AG
Shifter Drive Lever
AE
Pinch Double Action Lever AD
Reverse Guide Lever Ass’y AL
Reverse Drive Lever
AD
Slow Brake Lever
AE
Open Lever
AD
Clutch Lever
AE
Supply Main Brake Ass’y AF
Take-up Main Brake Ass’y AF
Shifter
AH
Reverse Guide Spring 2
AE
Loading Double Action
AE
Spring
Pinch Double Action
AD
Spring
Earth Spring
AC
Tension Spring
AD
Reel Belt
AE
Reel Disk
AE
Loading Connect Gear
AD
Master Cam
AE
Casecon Drive Gear
AD
Take-up Loading Gear
AF
Supply Loading Gear
AD
Description
Pinch Drive Cam
Reel Relay Gear
Worm Gear
Worm Wheel Gear
Idler Wheel Ass’y
Motor Pulley
Limiter Pulley Ass’y
Guide Roller
Tension Pole Adjuster
Guide Roller Spring
Light Guide
FFC for Drum Motor
FFC for A/C Head
A/C Head PWB
Socket, 6 pin
Full Erase Head
A/C Head Ass’y
Loading Motor
Capstan D.D. Motor
Drum Drive Motor
(VC-H810U)
Drum Drive Motor
(VC-A410U)
Upper and Lower
Drum Ass’y(VC-A410U)
Upper and Lower
Drum Ass’y(VC-H810U)
Drum Earth Brush
Drum Drive Motor
Mounting Screw
(SW2.6P+5S)
Drum Base
PWB(LDG Motor)
Socket(LDG Motor)
Azimuth Spring
Height Adjusting Spring
Code
AE
AE
AD
AD
AK
AD
AM
AL
AB
AC
AE
AD
AD
AE
AB
AM
AV
AP
AY
AT
AT
BU
BU
AD
AA
AL
AE
AE
AC
AC
SCREW, NUTS AND WASHERS
201
202
203
207
208
209
210
211
212
213
214
216
218
219
220
221
222
223
XBPSD26P08000
LX-HZ3082GEZZ
XJPSD26P06000
V Screw 2.6P+8S A/C Head
J WSW 2.6+6 (AC)
V Screw, C2.6P+6S
(For Capstan Motor)
XHPSD30P08WS0 V Screw, C3.0P+8S
(For Drum Base)
XRESJ30-06000
V E-Ring, E-3
XWHJZ31-03052
V Washer, W3.1-5.2-0.3
XWHJZ31-04052
V Washer, W3.1-5.2-0.4
XWHJZ31-05052
V Washer, W3.1-5.2-0.5
XWHJZ31-06052
V Washer, W3.1-5.2-0.6
XWHJZ31-07052
V Washer, W3.1-5.2-0.7
PSPAP0009AJZZ V Reverse Guide Adjusting
Nut
LX-WZ1041GE00 J CW 2.6-6-0.5 CAM
XBPSD30P06J00 V Drum Base Mounting
Screw(SW 3P+6S)
LX-WZ1098GE00 J CW 2.6-4.7-0.5 RED
LX-BZ3096GEFD
J Tilt Adjusting Screw
XBPSD26P06000 V Azimuth Adjusting Screw
2.6+6S
LX-BZ3197GEFD
J Screw(A/C Head)
XWHJZ31-08052
V Washer, W3.1-5.2-0.8
AA
AD
AA
AA
AA
AC
AC
AC
AC
AC
AB
AA
AA
AB
AA
AA
AD
AC
CASSETTE HOUSING CONTROL PARTS
79
300
CHLDX3081TEV2
301
302
303
LANGF9592AJFW
LHLDX1028AJ00
LHLDX1030AJZZ
V Cassette Housing Control AX
Ass’y
V Upper Plate
AL
V Frame (L)
AH
V Holder (L)
AE
VC-A410U
VC-H810U
Ref. No.
Part No.
★
Description
Code
304
305
306
307
308
309
310
311
312
313
314
315
316
317
LHLDX1031AJZZ
LHLDX1032AJ00
MLEVF0469AJFW
MLEVP0281AJ00
MSLiF0076AJFW
MSPRD0151AJFJ
MSPRD0166AJFJ
MSPRP0175AJFJ
MSPRT0381AJFJ
NGERH1278AJZZ
NGERH1309AJZZ
NGERR1008AJ00
NGERR3005AJFW
NSFTD0041AJFD
V
V
V
V
V
V
V
V
V
V
V
V
V
V
Holder (R)
Frame (R)
Proof Lever (R)
Door Open Lever
Slider
Proof Lever (R) Spring
Drive Gear (R) Spring
Cassette Spring
Double Action Spring
Drive Gear L
Drive Gear R
Double Action Rack Gear
Drive Angle Gear
Main Shaft
AE
AH
AE
AD
AK
AB
AE
AE
AC
AE
AE
AE
AG
AH
Ref. No.
Part No.
602
603
604
605
606
607
608
609
610
611
612
613
614
614
614
614
615
616
V Operation Manual
(for U.S.A)
TiNS-3756AJZZ
V Operation Manual
(for Canada)
QCNW-8115AJZZ V 75 ohm Coaxial Cable
RRMCG1236AJSA V Infrared Remote Control
Unit
500
500-1
500-2
500-3
500-3
500-4
500-5
500-6
500-7
501
502
CPNLC2721TEV1
V Front Panel Ass’y
(VC-A410U)
CPNLC2707TEV1 V Front Panel Ass’y
(VC-H810U)
—————
- Front Panel
(Not Replacement Item)
GCOVA2163AJZZ V Timer LED Cover
HDECQ2004AJSA V Cassette Flap(VC-A410U)
HDECQ2005AJSA V Cassette Flap(VC-H810U)
HDECQ2160AJSA V Window Dec.
JBTN-2943AJSB
V Button, REC
HINDP2132AJSA V Timer LED Indicator
MSPRD0103AJFJ V Cassette Spring
JBTN-2942AJSA
V Button, PLAY
LHLDZ2066AJZZ
V Button Holder
AF
AH
AG
AS
ACCESSORY
(NOT REPLACEMENT ITEM)
AT
AQ
AE
- Guarantee Card
(for U.S.A)
—
PACKING PARTS
(NOT REPLACEMENT ITEM)
AE
SPAKC4268AJZZ
SPAKC4267AJZZ
SPAKX1073AJZZ
TLABK0005AJZZ
AD
AA
AA
AG
AB
AA
AA
AB
AD
AD
AB
AC
AC
AC
AC
AA
AC
FRONT PANEL PARTS
500
Code
ACCESSORIES
TiNS-3737AJZZ
CABINET PARTS
GCABA3136AJSM V Top Cabinet
GCABB1223AJKB V Main Frame
GCOVA2072AJKZ V Antenna Terminal Cover
(VC-A410U)
GCOVA2073AJKZ V Antenna Terminal Cover
(VC-H810U)
PSLDM4566AJFW V Shield Angle
XHPSD26P06WS0 V Screw
XHPSD30P06WS0 V Screw
LANGK0197AJFW V Top Cabinet Fix Angle
XEPSD30P14XS0 V Screw
LX-HZ3047GEFF
J Screw
XEBSD30P12000 V Screw
LX-HZ3087GEFN J Screw
PSLDM4575AJFW V H/A Shield(Bottom)
LHLDZ1962AJ00
V Sensor LED Cover
PGUMS0026AJZZ V Foot Cushion
TLABM4190AJZZ V Model Label(VC-A410U)
TLABM4189AJZZ V Model Label(VC-H810U)
TLABM4210AJZZ V Model Label
(VC-A410U for Canada)
TLABM4209AJZZ V Model Label
(VC-H810U for Canada)
XJPSD30P10WS0 V Screw
LHLDP1197AJZZ V LED Holder
Description
SUPPLIED ACCESSORIES
TGAN-0001AJZZ
600
601
602
★
AU
AU
—
AL
AH
AH
AG
AE
AD
AB
AH
AC
80
-
Packing Case(VC-A410U)
Packing Case(VC-H810U)
Packing Foam
No. Label
—
—
—
—
VC-A410U
VC-H810U
Part No.
★
Description
Code
Ref.
No.
11. EXPLODED
VIEW
OF MECHANICAL
PARTS
Ref. No.
★
Part No.
Description
Code
MECHANISM CHASSIS PARTS
66
66
H
62
53
55
66
222
202
220
66
70
65
221
62
G
57
56
59
63
201
202
202
207
207
16
50
71
F
1
49
67
22
51
218
49
15
58
33
E
8
51
52
2
24
31
32
25
11
214
12
4
7
19
18
20
203
D
29
35
35
46
C
5
209
210
211
212
213
223
216
41
43
61
43
23
9
21
10
B
39
30
30
36
38
34
17
40
37
48
6
45
208
44
27
47
60
219
A
68
69
1
2
3
4
81
5
6
VC-A410U
VC-H810U
Part No.
★
Description
Code
CASSETTE
HOUSING
CONTROL
PARTS
Ref. No.
Ref. No.
★
Part No.
Description
Code
300
H
301
G
303
302
311
F
311
304
306
308
309
E
313
310
317
D
305
314
312
C
307
315
316
B
A
1
2
3
4
82
5
6
VC-A410U
VC-H810U
Part No.
CABINET
PARTS★
Ref. No.
Description
Code
Ref. No.
Part No.
★
Description
Code
608
H
VC-H810U
600
602
609
G
605
C
615
F
602
VC-A410U
607
B
604
A
615
603
E
612
611
D
A
616
C
614
610
C
B
B
605
606
613
601
A
615
609
1
2
3
4
83
5
6
VC-A410U
VC-H810U
Ref. No.
★
Part No.
Description
FRONT PANEL PARTS
Code
Ref. No.
Part No.
★
Description
Code
F
500-7
500-3
E
500-2
D
500-1
500-4
C
500-6
500-5
500
B
PL
RE
AY
W
502
FF
ST
OP
501
A
1
2
3
4
5
6
PRECAUTION ON FRONT PANEL SET-UP
Cassette cover
Front panel
3
4
Cassette housing
Cassette cover
open lever
Cassette cover
1
Cassette cover
open lever
Cassette cover
open lever
2
5
About 45°
Before attaching the front
panel in position, make
sure that the cassette cover
open lever is in its right
place (lower-most). If it is
out of position, push it down
with a finger.
Keep the cassette over about
45° open and make sure that
the cassette cover open lever is between the front panel
and the cassette cover. Now
fix the front panel in place.
84
Do not mount the front
panel with the cassette
cover tilted too open.
Otherwise the cassette
cover might wrongly run
on the cassette housing.
Removing the cassette compartment cover.
1 Open the cassette compartment cover
fully.
2 Remove the center positioner.
3 Slide the cover to the right.
4 Slightly bend the cover.
5 Draw out the left-side rod.