DS6751/DS6751-2/DS6751-3
Go to www.vtechphones.com to register your product
for enhanced warranty support and latest VTech product news.
Abridged user’s manual
Introduction
To protect our environment and conserve natural resources, this
Abridged user’s manual provides you with basic installation and use instructions.
A limited set of features are described in abbreviated form.
Please refer to the online User’s manual for a full set of installation and operation
instructions at www.vtechphones.com.
Before using this VTech product, please read Important safety instructions on
page 2 of this user’s manual.
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Telephone base
Handset
(1 for DS6751)
(2 for DS6751-2)
(3 for DS6751-3)
Telephone line cord
Telephone base
power adapter
Handset battery
compartment cover
(1 for DS6751)
(2 for DS6751-2)
(3 for DS6751-3)
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
Inside your package
Battery
(1 for DS6751)
(2 for DS6751-2)
(3 for DS6751-3)
Handset charger and
charger adapter
(1 for DS6751-2)
(2 for DS6751-3)
Abridged user’s manual
Abridged user’s manual
Quick start guide
Quick start guide
BC
Important safety instructions
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk
of fire, electric shock and injury, including the following:
. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a
damp cloth for cleaning.
4. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or
swimming pool, or in a wet basement or shower.
5. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
6. Avoid placing the telephone system in places with extreme temperature, direct sunlight, or other electrical
devices. Protect your phone from moisture, dust, corrosive liquids and fumes.
7. Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation.
To protect them from overheating, these openings must not be blocked by placing the product on a soft
surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat
register. This product should not be placed in any area where proper ventilation is not provided.
. This product should be operated only from the type of power source indicated on the marking label. If you
are not sure of the type of power supply in your home or office, consult your dealer or local power company.
9. Do not allow anything to rest on the power cord. Do not install this product where the cord may be walked on.
0. Never push objects of any kind into this product through the slots in the telephone base or handset because
they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.
. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service
facility. Opening or removing parts of the telephone base or handset other than specified access doors
may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock
when the product is subsequently used.
2. Do not overload wall outlets and extension cords.
3. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the
following conditions:
• When the power supply cord or plug is damaged or frayed.
• If liquid has been spilled onto the product.
• If the product has been exposed to rain or water.
• If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operation instructions. Improper adjustment of other controls may
result in damage and often requires extensive work by an authorized technician to restore the product
to normal operation.
• If the product has been dropped and the telephone base and/or handset has been damaged.
• If the product exhibits a distinct change in performance.
14.Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric
shock from lightning.
15.Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain circumstances, a
spark may be created when the adapter is plugged into the power outlet, or when the handset is replaced
in its cradle. This is a common event associated with the closing of any electrical circuit. The user should
not plug the phone into a power outlet, and should not put a charged handset into the cradle, if the
phone is located in an environment containing concentrations of flammable or flame-supporting gases,
unless there is adequate ventilation. A spark in such an environment could create a fire or explosion.
Such environments might include: medical use of oxygen without adequate ventilation; industrial gases
(cleaning solvents; gasoline vapors; etc.); a leak of natural gas; etc.
16.Only put the handset of your telephone next to your ear when it is in normal talk mode.
17.The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs
are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.
SAVE THESE INSTRUCTIONS
Battery
• CAUTION: Use Only Supplied Battery.
• Do not dispose of the battery in a fire. Check with local waste management codes for special disposal instructions.
• Do not open or mutilate the battery. Released electrolyte is corrosive and may cause burns or injury to the
eyes or skin. The electrolyte may be toxic if swallowed.
• Exercise care in handling batteries in order not to create a short circuit with conductive materials.
• Charge the battery provided with this product only in accordance with the instructions and limitations
specified in this manual.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless telephones):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation
of the interference between portable wireless telephones and implanted cardiac pacemakers. Supported by
the U.S. Food and Drug Administration, WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless telephones at least six inches from the pacemaker.
• Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it is
turned ON.
• Should use the wireless telephone at the ear opposite the pacemaker. WTR’s evaluation did not identify
any risk to bystanders with pacemakers from other persons using wireless telephones.
Operating range
This cordless telephone operates with the maximum power allowed by the Federal Communications Commission
(FCC). Even so, this handset and telephone base can communicate over only a certain distance - which can vary
with the locations of the telephone base and handset, the weather, and the layout of your home or office.
When the handset is out of range, the handset displays Out of range or no pwr at base.
If there is a call while the handset is out of range, it may not ring, or if it does ring, the call may not connect
well when you press /HOME. Move closer to the telephone base, then press /HOME to answer the call.
If the handset moves out of range during a telephone conversation, there may be interference. To improve
reception, move closer to the telephone base.
About cordless telephones
•
•
•
•
•
Privacy: The same features that make a cordless telephone convenient create some limitations.
Telephone calls are transmitted between the telephone base and the cordless handset by radio waves,
so there is a possibility that the cordless telephone conversations could be intercepted by radio receiving
equipment within range of the cordless handset. For this reason, you should not think of cordless
telephone conversations as being as private as those on corded telephones.
Electrical power: The telephone base of this cordless telephone must be connected to a working electrical
outlet. The electrical outlet should not be controlled by a wall switch. Calls cannot be made from the cordless
handset if the telephone base is unplugged, switched off or if the electrical power is interrupted.
Potential TV interference: Some cordless telephones operate at frequencies that may cause interference
to televisions and VCRs. To minimize or prevent such interference, do not place the telephone base of
the cordless telephone near or on top of a TV or VCR. If interference is experienced, moving the cordless
telephone farther away from the TV or VCR often reduces or eliminates the interference.
Rechargeable batteries: Exercise care in handling batteries in order not to create a short circuit with
conducting material such as rings, bracelets and keys. The battery or conductor may overheat and cause
harm. Observe proper polarity between the battery and the battery charger.
Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do not burn
or puncture the battery. Like other batteries of this type, if burned or punctured, they could release caustic
material which could cause injury.
Get started
Connect the telephone base and handset charger
Click!
DSL filter
Plug!
TEL. LINE
•
•
•
Use Only
Supplied Adapter
DC 6V
Click!
Plug!
Plug!
Use only the power adapters and batteries supplied with this product.
To order replacements, visit our website at www.vtechphones.com or call
1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call
1 (800) 267-7377.
Even if you do not subscribe to any conventional telephone service, you can still
use the cell line alone without plugging in a telephone line cord.
If you subscribe to telephone service from a cable company or a VoIP service
provider, contact your cable/VoIP service provider for more information.
Install battery
3
2
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Plug!
4
Click!
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
1
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
IMPORTANT:
Press
/HOME to check for a dial tone. If you hear a dial tone, the installation is successful.
If you do not hear a dial tone:
•
Make sure the installation procedures described above are properly done.
•
It may be a wiring problem. If you have changed your telephone service to digital service
from a cable company or a VoIP service provider, the telephone line may need to be
rewired to allow all existing telephone jacks to work. Contact your cable/VoIP service
provider for more information.
Charge your phone
Light on!
The battery icon
•
•
•
Animates when the battery is charging.
Flashes when the battery is low and
needs charging.
Becomes solid when the battery is
fully charged.
Charge for at least 30 minutes before initial settings.
Charge for 11 hours before initial use.
Configure your phone
Set date and time
. Press MENU when the telephone base/handset is not in use.
2. Scroll to Set date/time, then press SELECT.
3. Enter the month (MM), date (DD) and year (YY), then press SELECT.
4. Enter the hour (HH) and minute (MM). Then scroll to AM or PM.
5. Press SELECT.
If you subscribe to caller ID service, the day, month and time are set automatically
with each incoming call.
ECO mode
This power conserving technology reduces power
consumption for optimal battery performance.
The ECO mode activates automatically whenever
the handset is synchronized with the telephone base.
The handset shows ECO when the ECO mode activates.
HANDSET 1
ECO
10:15 P M
12/18
ECO
Handset overview
1
8
2
9
3
10
11
4
5
6
12
7
13
14
1 – CHARGE light
2–
/CELL
• Make or answer a cell call.
• Answer a call waiting cell call.
3–
/HOME/FLASH
• Make or answer a home call.
• Answer a call waiting home call.
4–
1
• Set or dial your voicemail number.
10 – OFF/CANCEL
• Hang up a call.
• Silence the ringer temporarily.
• Erase the missed call indicator.
• Return to the previous menu or idle
mode without making changes.
11 – CID/ /VOLUME
• Scroll down while in a menu, or in the
directory, caller ID log or redial list.
• Decrease the listening volume.
• Review the caller ID log.
12 – QUIET#
• Set and turn on the quiet mode, or
turn it off.
• Show other dialing options when
reviewing a caller ID log entry.
5 – Dialing keys
6 – TONE
• Switch to tone dialing temporarily.
7 – MUTE/DELETE
• Mute a call.
• Delete a digit or character.
• Silence the ringer temporarily.
• Delete the displayed entry when
reviewing the directory, caller ID log
or redial list.
8–
13 – REDIAL/PAUSE
• Review the redial list.
• Insert a dialing pause.
14 –
/ /VOLUME
• Scroll up while in a menu, or in the
directory, caller ID log or redial list.
• Increase the listening volume.
• Review the directory.
9 – MENU/SELECT
• Show the menu.
• Select an item or save an entry or
setting in a menu.
• Make a home call or answer a home
or cell call.
• Switch between the speakerphone and
the handset earpiece.
Telephone base overview
11
12
1
13
2
3
14
15
16
4
5
17
18
19
20
6
7
21
22
8
9
10
1 – MENU/SELECT
• Show the menu.
• Select an item or save an entry or
setting in a menu.
2–
/CID
• Scroll down while in a menu, or in the
directory, caller ID log or redial list.
• Review the caller ID log.
3 – CANCEL
• Silence the ringer temporarily.
• Erase the missed call indicator.
• Return to the previous menu or idle
mode without making changes.
4–
1/
2
• Pair or replace a cell phone.
• Cancel the pairing process.
13 –
1/
2 device lights
• On when the telephone base is
paired and connected with a Bluetooth
cell phone.
• Blinks when the telephone base
is pairing and connecting with a
Bluetooth cell phone.
14 –
/ANS ON/OFF
• Turn on or off the answering system.
15 – X/DELETE
• Delete the playing message.
• Delete a digit or character.
• Delete the displayed entry when
reviewing the directory, caller ID log
or redial list.
1
• Set or dial your voicemail number.
5 – Flash
• Answer a call waiting call.
6–
12 –
16 – MUTE
• Mute a call.
• Silence the ringer temporarily.
/VOL/
• Adjust the listening volume.
7 – REDIAL/PAUSE
• Review the redial list.
• Insert a dialing pause.
17 – FIND HANDSET
• Page all system handsets.
8 – Dialing keys
18 –
9 – TONE
• Switch to tone dialing temporarily.
/SKIP
• Skip to the next message.
19 –
/REPEAT
• Repeat a message.
• Press twice to play the previous
message
20 –
/HOME
• Make or answer a home call.
21 –
/PLAY/STOP
• Play messages.
• Stop playing messages.
22 –
/CELL
• Make or answer a cell call.
10 – QUIET#
• Set and turn on the quiet mode, or
turn it off.
• Show other dialing options when
reviewing a caller ID log entry.
11 –
/
• Scroll up while in a menu, or in the
directory, caller ID log or redial list.
• Review the directory.
Handset and telephone base display icons
•
The battery icon flashes when the battery is low and needs charging.
•
The battery icon animates when the battery is charging.
•
•
•
•
The home line is in use or there is an incoming home call.
There are Bluetooth connected devices on the cell device list.
•
•
•
1
2
The battery icon becomes solid when the battery is fully charged.
The handset/telephone base ringer is turned off.
There are new voicemail received from the telephone service provider.
The cell line is in use or there is an incoming cell call.
/
MSG#
1/13 13
The message number currently playing and total number of
messages recorded.
•
ANS ON
The answering system is turned on.
•
ECO
The ECO mode activates automatically to reduce power consumption
whenever the handset is synchronized with the telephone base.
•
NEW/NEW The caller ID log entry you are reviewing is new.
The message you are listening is new.
Built-in answering system and voicemail
This telephone has a built-in answering system which can be used without any
service subscription.
This telephone also supports voicemail feature which requires subscription from
your telephone service provider. Contact your telephone service provider for details.
To configure some common settings for the answering system
Record your own announcement
You can use the preset announcement to answer calls, or replace it with your own
recorded announcement. The announcement can be up to 90 seconds in length.
. Press MENU when the phone is not in use.
2. Scroll to Answering sys, then press SELECT twice.
3. The system announces, “To play, press 2. To record, press 7.” Then press 7
to record.
4. The system announces, “Record after the tone. Press 5 when you are done.”
After the tone, speak towards the microphone.
5. Press 5 when done.
Set number of rings
You can set the answering system to answer an incoming call after two, three,
four, five or six rings; or toll saver. If you choose toll saver, the answering system
answers a call after two rings when you have new messages, or after four rings
when you have no new messages.
. Press MENU when the phone is not in use.
2. Scroll to Answering sys, then press SELECT.
3. Scroll to Ans sys setup, then press SELECT.
4. Scroll to # of rings, then press SELECT.
5. Scroll to 6, 5, 4, 3, 2 or Toll saver and then press SELECT.
To configure the voicemail number and retrieve voicemail messages
You can save the voicemail number to
1 on each handset and the telephone
base for easy access. Contact your telephone service provider for more information
and assistance about using your voicemail service.
Set voicemail number:
Press MENU when the phone is not in use.
Scroll to Settings, then press SELECT.
Scroll to Voicemail #, then press SELECT.
Enter the voicemail number.
• Press DELETE to erase a digit.
• Press and hold DELETE to erase all digits.
• Press or to move the cursor to the left or right.
• Press and hold PAUSE to insert a dialing pause (a P appears).
• Press TONE to add ( appears) or QUIET# to add # ( appears).
5. Press SELECT.
1.
2.
3.
4.
Retrieve voicemail messages:
Press and hold
1.
Bluetooth
Pair and connect your first Bluetooth cell phone
To use a Bluetooth enabled cell phone with your DS6751, you must first pair and
connect your Bluetooth cell phone(s) with the telephone base. All DS6751 handsets
can be used to make or answer calls on the cell line.
. Press 1 / 2 on the telephone base. You hear two beeps. The telephone
base screen displays Pairing D1... and the 1 device light blinks.
2. Turn on the Bluetooth feature of your cell phone. Once your cell phone finds your
VTech phone (VTech DS6751), press the appropriate key on your cell phone to
continue the pairing process.
• Your cell phone may prompt you to enter the PIN of the telephone base. The
default PIN of the telephone base is 0000.
• Bluetooth wireless technology operates within a short range (a maximum of
approximately 30 feet). When you pair a Bluetooth cell phone to the telephone
base, make sure your Bluetooth cell phone is close to the telephone base to
maintain sufficient signal strength. For optimal performance, keep your cell
phone within 15 feet of the telephone base while using the cell line.
• If the pairing fails, turn off the Bluetooth feature on your cell phone and on the
DS6751 by pressing 1 / 2. Then repeat the steps above to pair and connect
again. In some cases, it may take you a few attempts to complete the pairing process.
VTech Connect to Cell application
TM
This application helps you integrate your Android phones with
your DS6751. For more information and application download,
go to http://www.vtechphones.com/app_connect_to_cell
Download directory
.
2.
3.
4.
Press MENU when the phone is not in use.
Scroll to Bluetooth, then press SELECT.
Scroll to Download dir, then press SELECT.
Scroll to select the desired cell phone, then press SELECT.
• For certain cell phones, you may need to press a key on your cell phone to
confirm the directory download.
•
•
•
The performance of directory download feature depends on the compatibility of
your Bluetooth cell phone. Refer to the user’s manual of your cell phone for more
information about how that device uses Bluetooth connectivity.
Certain cell phones do not support SIM card download. If this is the case, transfer
the contacts from your SIM card to our cell phone memory first. Then, download from
your cell phone memory. For more information on how to transfer contacts from your
SIM card to your cell phone memory, see the user’s manual of your cell phone.
For Android cell phones, you may also download your cell phone
directory to your DS6751 via the VTech Contact Share application.
Go to http://www.vtechphones.com/app_contact_share for
application download.
Telephone settings
The following are some of the telephone features you may wish to set. Refer to
Telephone settings in the online User’s manual for detailed instructions on setting
all telephone features.
To access the Settings menu, press MENU when the phone is not in use. Scroll to
Settings, and then press SELECT. Default settings are indicated by asterisks (*).
Settings menu
Description
Options
LCD language
Set the screen display language.
English*;
Français;
Español
Clr voicemail
Turn off the voicemail indicators (see the
note below).
Reset VM Icon?
Key tone
Turn an audible beep on or off whenever a
key is pressed.
Key tone:On*;
Key tone:Off
Home area code
Set the home area code so that the
caller ID log stores only seven digits for local
telephone numbers.
Home area code
___
Dial mode
Set the telephone to be touch-tone or
pulse dialing.
Touch-tone*;
Pulse
The Clr voicemail feature turns off the indicators, but it does not delete your voicemail
messages. After you have listened to all new voicemail messages, the indicators turn off
automatically. When you have new voicemail messages, your telephone service provider
will send the signal and turn on the indicators.
Ringer volume
You can adjust the ringer volume level, or turn the ringer off.
. Press MENU when the telephone base/handset is not in use.
2. Scroll to Ringers, then press SELECT.
3. Scroll to Home volume or Cell volume, then press SELECT.
4. Scroll to adjust the volume, then press SELECT.
Quiet mode
You can turn on the quiet mode for a period of time. During this period, all tones
(except paging tone) and the call screening are muted. When you turn on the quiet
mode, the answering system turns on automatically.
. Press and hold QUIET# when the telephone base/handset is not in use.
2. Enter the desired duration, then press SELECT.
• To turn off the quiet mode, press and hold QUIET# when the telephone base/
handset is not in use.
Telephone operations - Calls
Make a home call with a handset:
•
Press
/HOME or
, and then dial the telephone number.
Make a home call at the telephone base:
•
Press
/HOME, then dial the telephone number.
Make a cell call with a handset:
. Press /CELL. Scroll to select the desired cell phone when
necessary, then press SELECT.
2. Enter the telephone number and then press /CELL to dial.
While using the cell line, place your cell phone closer to the telephone base, and
make sure that there are no physical obstacles between the telephone base and the
cell phone, such as large furniture or thick walls.
Make a cell call at the telephone base:
. Press /CELL. Scroll to select the desired cell phone when necessary, then
press SELECT.
2. Enter the telephone number and then press /CELL or SELECT to dial.
Answer a home/cell call with a handset:
•
Press
/HOME,
/CELL,
or any dialing keys.
Answer a home/cell call at the telephone base:
•
Press
/HOME,
/CELL or any dialing keys.
End a home/cell call with a handset:
•
Press OFF or return the handset to the telephone base or handset charger.
End a home/cell call at the telephone base:
•
•
For a home line call, press /HOME.
For a cell line call, press /CELL.
Call waiting
When you subscribe to call waiting service from your telephone service provider, you
hear an alert tone if there is an incoming call while you are already on another call.
Call waiting on the home line:
• Press FLASH to put the current call on hold and take the new call.
• Press FLASH at any time to switch back and forth between calls.
Call waiting on the cell line:
• Press /CELL on the handset or FLASH on the telephone base to put the
current call on hold and take the new call.
• Press /CELL on the handset or FLASH on the telephone base at any time to
switch back and forth between calls.
Handset speakerphone:
•
During a call, press
to switch between the speakerphone and handset earpiece.
Telephone operations - Adjust volume
Volume
To adjust the listening volume on a handset:
•
During a call, press
/VOLUME or
/VOLUME.
To adjust the listening volume at the telephone base:
•
During a call, press
/VOL or
/VOL.
The handset earpiece volume setting and speakerphone volume setting are independent.
Mute
The mute function allows you to hear the other party but the other party cannot hear you.
• To mute a call on a handset, press MUTE. The handset displays Muted. Press
MUTE again to resume the conversation.
• To mute a call at the telephone base, press MUTE. The telephone base displays
Muted and the MUTE light turns on. Press MUTE again to resume the conversation.
Temporary ringer silencing
When the telephone is ringing, you can temporarily silence the telephone base/handset
ringer without disconnecting the call. The next call rings normally at the preset volume.
• To silence the handset ringer, press OFF or MUTE on the handset.
displays
and Ringer muted displays briefly.
• To silence the telephone base ringer, press MUTE, CANCEL or /VOL on the
telephone base.
displays and Ringer muted displays briefly.
Telephone operations - Multiple device use
Join a call in progress
You can use the telephone base and a handset, or two handsets at a time on
a home line call. You can buy additional expansion handsets (DS6701) for this
telephone base. You can register up to five handsets to the telephone base.
• When a device is on a home line call, press /HOME or
on another handset,
or press /HOME on the telephone base.
• To exit the call, press OFF on the handset, return it to the telephone base or
handset charger, or press /HOME on the telephone base. The call continues
until all devices hang up.
Transfer a call
While on an outside call, you can transfer the call from one system device to another.
Using a handset:
. During a call, press MENU.
2. Scroll to Transfer, then press SELECT. When you have more than one handset,
enter a destination device number (7 for the telephone base, or 1 to 5 for
HANDSET 1 to HANDSET 5).
3. To answer the call on the telephone base or a handset, press /HOME,
/CELL,
or any dialing keys.
Using the telephone base:
. During a call, press MENU.
2. When you have only one handset, the screen displays Transfer call?
Press SELECT.
-ORWhen you have more than one handset, enter a destination handset number
(1 to 5 for HANDSET 1 to HANDSET 5).
3. To answer the call on a handset, press /HOME, /CELL or any dialing keys.
Intercom
Use the intercom feature for conversations between the telephone base and a
handset, or two handsets.
. Press MENU on the telephone base/handset when not in use.
2. Scroll to Intercom, then press SELECT. When you have more than one
handset, enter a destination device number (7 for the telephone base, or 1 to 5
for HANDSET 1 to HANDSET 5).
3. To answer the intercom call with the destination handset, press /HOME,
/CELL,
or any dialing keys.
-ORTo answer the intercom call with the telephone base, press /HOME, /CELL
or any dialing keys.
4. To end the intercom call while using a handset, press OFF or return the handset
to the telephone base or handset charger.
-ORTo end the intercom call while using the telephone base, press� /HOME.
Answer an incoming call during an intercom call
When you receive an outside call during an intercom call, there is an alert tone.
Using a handset:
• To answer a home call, press /HOME. The intercom call ends automatically.
• To answer a cell call, press OFF to end the intercom call. The telephone
continues to ring. Then press
/CELL.
• To end the intercom call without answering the outside call, press OFF. The
intercom call ends and the telephone continues to ring.
Using the telephone base:
• To answer a home call, press /HOME to end the intercom call. The telephone
continues to ring. Then press /HOME.
• To answer a cell call, press /HOME to end the intercom call. The telephone
continues to ring. Then press
/CELL.
• To end the intercom call without answering the outside call, press /HOME.
The intercom call ends and the telephone continues to ring.
Telephone operations - Others
Temporary tone dialing
If you have pulse (rotary) service only, you can switch from pulse to tone dialing
temporarily during a call.
. During a call, press TONE .
2. Use the dialing keys to enter the relevant number. The telephone sends
touch-tone signals. It automatically returns to pulse dialing mode after you
end the call.
Find handset
Use this feature to find all system handsets.
To start paging:
• Press FIND HANDSET at the right side of the telephone base
and it displays ** Paging **. All idle handsets ring and display
** Paging **.
To end paging:
• Press /HOME, /CELL, , OFF or any dialing keys on a
handset.
-OR• Return the handset to the telephone base or handset charger.
-OR• Press FIND HANDSET on the telephone base.
Do not press and hold FIND HANDSET for more than four seconds. It may lead to
handset deregistration.
Directory
The directory can store up to 200 entries which are shared by the telephone base
and all system handsets.
To add a directory entry:
Press MENU when the phone is not in use.
Scroll to Directory, then press SELECT.
Scroll to Add contact, then press SELECT.
Enter the number (up to 30 digits).
-ORCopy a number from the redial list by pressing REDIAL and then press ,
REDIAL repeatedly to select a number. Press SELECT.
5. Press SELECT to move to the name.
6. Enter the name (up to 15 characters). Additional key presses show other
characters of that particular key.
7. Press SELECT to save.
.
2.
3.
4.
or
While entering names and numbers, you can:
• Press DELETE to backspace and erase a digit or character.
• Press and hold DELETE to erase the entire entry.
• Press and hold PAUSE to insert a dialing pause (for entering phone numbers only).
• Press or to move the cursor to the left or right.
• Press 0 to add a space (for entering names only).
• Press TONE to add ( appears) or QUIET# to add # ( appears).
To review and dial from the directory:
Entries are sorted alphabetically.
when the phone is not in use.
. Press
2. Scroll to browse through the directory, or use the dialing keys to start a
name search.
3. To dial the displayed entry with the handset, press /HOME, /CELL, or
-ORTo dial the displayed entry with the telephone base, press /HOME
or /CELL.
.
To edit a directory entry:
. When the desired entry displays, press SELECT.
2. Edit the number when necessary, then press SELECT.
3. Edit the name when necessary, then press SELECT.
To delete a directory entry:
. When the desired entry displays, press DELETE.
2. When the screen displays Delete contact?, press SELECT.
To delete all directory entries:
.
2.
3.
4.
Press MENU when the phone is not in use.
Scroll to Directory, then press SELECT.
Scroll to Del all conts, press SELECT.
When the screen displays Delete all?, press SELECT.
Speed dial
You can copy up to nine directory entries into the speed dial locations (0 and 2-9)
so that you can dial these numbers via the home line more quickly.
To assign a speed dial entry:
. Press MENU when the phone is not in use.
2. Scroll to Directory, then press SELECT.
3. Scroll to Speed dial, then press SELECT.
4. Scroll to a desired speed dial location, then press SELECT.
5. Scroll to a desired directory entry, then press SELECT.
10
To dial a speed dial entry:
• Press and hold a dialing key (0 or 2-9) to dial the number stored in the
corresponding location.
To delete a speed dial entry:
. Press MENU when the phone is not in use.
2. Scroll to Directory, then press SELECT.
3. Scroll to Speed dial, then press SELECT.
4. Scroll to a desired speed dial location, then press DELETE. The screen displays
Clear SD #X? Press SELECT.
Caller ID
This product supports caller ID services provided by most telephone service
providers. Depending on your service subscription, you may see the caller’s name,
number, date and time of calls that are sent by your telephone service provider after
the first or second ring.
Caller ID log
The caller ID log stores up to 50 entries. If you answer a call before the caller
information appears, it will not be saved in the caller ID log.
• The telephone base and handset display XX missed calls when there are calls
that have not been reviewed in the caller ID log.
• If you want to erase the missed call indicator, press and hold CANCEL when the
telephone base/handset is not in use.
To review and dial a number in the caller ID log:
. Press CID when the phone is not in use.
2. Scroll to browse through the caller ID log. When the desired entry appears:
• Press QUIET# repeatedly to show different dialing options.
• Press 1 repeatedly if you need to add or remove 1 in front of the phone number.
3. To dial the displayed number with a handset, press /HOME, /CELL or .
-ORTo dial the displayed number with the telephone base, press /HOME
or /CELL.
To save a caller ID log entry to the directory:
. When the desired caller ID log entry displays, press SELECT.
2. Modify the number when necessary, then press SELECT.
3. Modify the name when necessary, then press SELECT to save.
To delete a caller ID log entry:
•
When the desired caller ID log entry displays, press DELETE.
To delete all caller ID log entries:
. Press MENU when the phone is not in use.
2. Scroll to Caller ID log, then press SELECT.
3. Scroll to Del all calls, then press SELECT twice.
Redial list
Each handset and the telephone base store the last 10 telephone numbers dialed.
When there are already 10 entries, the oldest entry is deleted to make room for the
new entry.
To review and dial a number from the redial list:
. Press REDIAL when the telephone base/handset is not in use.
or REDIAL repeatedly until the desired entry displays.
2. Press� , , ���
3. Press /HOME or /CELL to dial.
To delete a redial entry:
•
When the desired redial entry displays, press DELETE.
About answering system and voicemail
Your telephone has separate indicators for two different types of voice messages:
those left on its built-in answering system and those left at your telephone service
provider’s voicemail. Each alerts you to new messages differently.
/PLAY/STOP on the telephone base flashes, and XX new messages
• If
displays on the handsets and telephone base, there are new messages in the
built-in answering system. It can record up to 99 messages, depending on the
length of each message. Each message can be up to three minutes in length.
The total recording time is approximately 14 minutes.
and New voicemail display on the handsets and the telephone base, your
• If
telephone service provider is indicating that it has new voicemail for you.
Contact your telephone service provider for more information on how to access
your voicemail.
11
Answering system settings
Default settings are indicated by asterisks (*).
Settings menu
Description
Options
Call screening
Set whether you hear the callers while they are
leaving messages to you.
Screening: On*;
Screening: Off
# of rings
Set the number of times the telephone rings before
the answering system answers.
6; 5; 4; 3*; 2;
Toll saver
Remote code
Set a two-digit security code to access the answering
system remotely from any touch-tone telephone.
19*
Msg alert tone
Set whether the telephone base beeps to alert you
of new messages.
Tone: Off*;
Tone: On
Recording time
Set the recording time for each incoming message.
3 minutes*;
2 minutes;
1 minute
Answering system operation
Turn the answering system on or off
The answering system must be turned on to answer and record messages.
• Press /ANS ON/OFF on the telephone base to turn the built-in answering
system on or off.
Message playback at the telephone base
•
Press
/PLAY when the telephone base is not in use.
Options during playback:
•
•
•
•
•
Press /VOL or /VOL to adjust the listening volume.
Press /SKIP to skip to the next message.
Press /REPEAT to repeat the playing message. Press /REPEAT twice to
listen to the previous message.
Press X/DELETE to delete the playing message. The system advances to the
next message.
Press
/STOP to stop.
Call intercept
If you want to talk to the person whose message is being recorded:
• On a handset, press /HOME or .
-OR• On the telephone base, press /HOME.
Remote access
You can access the answering system remotely from any touch-tone telephone.
The preset remote access code is 19.
. Dial your telephone number from any touch-tone telephone.
2. When the answering system answers, enter the two-digit remote access code.
3. Press 5 to hear a list of remote commands.
4. Enter the desired remote command code.
5. Hang up or press 8 to end the call.
12
Expand your telephone system
You can add new handsets (DS6701, purchased separately) to your telephone
system. Your telephone base supports a maximum of five handsets.
For more details, refer to the user’s manual that comes with your DS6701 new
handset.
Troubleshooting
If you have difficulty with your telephone, please try the suggestions below. For customer service, visit
our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to
www.vtechcanada.com or call 1 (800) 267-7377.
I cannot add and connect my cell phone to the telephone base.
• Make sure you have cellular coverage.
• Make sure your cell phone is compatible with your DS6751. Check the Bluetooth compatibility list
at www.vtechphones.com.
• Make sure the Bluetooth function of your cell phone is turned on. See the user’s manual of your
cell phone for more information.
• Make sure that your Bluetooth cell phone is not connected to any other Bluetooth device.
• To connect your cell phone, make sure that your cell phone is connected and active on the device list.
• Remove VTech DS6751 from your cell phone’s handsfree device history list (see the
user’s manual of your cell phone for more information).
• Carefully follow the pairing instructions on pages 6-7 and make sure that your cell phone is not
connected to any other Bluetooth device.
• Turn off your cell phone, then turn it on again.
• For some cell phones, you must authorize VTech DS6751 device in your cell phone’s Bluetooth
feature. See the user’s manual of your cell phone for more information.
• Manually connect your cell phone to VTech DS6751. Refer to the user’s manual of your
cell phone for more information.
• Reset the telephone base. Unplug the unit’s electrical power. Wait for approximately
15 seconds, then plug it back in. Repeat the above suggestions.
The PIN on the telephone base does not work.
• Make sure you enter the correct PIN. The default PIN is 0000.
Can the DS6751 help the poor cell phone reception in my house?
• If your cell phone has poor reception in your home, the DS6751 cannot improve the reception.
However, if there is a location in your house with better reception, you can leave your cell phone at
that location while you use the DS6751 cell line. In order for this to work, the telephone base must
be within 30 feet of the cell phone.
My telephone does not work at all.
• Make sure the battery is installed and charged correctly. For optimum daily performance, return
the handset to the telephone base or handset charger after use.
• Make sure the power adapter is securely plugged into an outlet not controlled by a wall switch.
• Make sure the telephone line cord is plugged firmly into the telephone base and the wall jack.
• Unplug the electrical power to the telephone base. Wait for approximately 15 seconds, then plug it back
in. Allow up to one minute for the cordless handset and telephone base to synchronize.
• Charge the battery in the cordless handset for at least 11 hours. For optimum daily performance,
return the cordless handset to the telephone base or handset charger after use.
• If the battery is completely depleted, charge the cordless handset for at least 30 minutes before use.
• Remove and install the battery again. If that still does not work, it may be necessary to purchase a
new battery.
• Disconnect the telephone base from the telephone wall jack and plug in a working telephone. If the
other telephone does not work, the problem is probably in the wiring or telephone service. Contact
your telephone service provider.
The display shows No line. I cannot hear the dial tone.
• Disconnect the telephone line cord from your telephone and connect it to another telephone.
If there is no dial tone on that other telephone either, then the telephone line cord may be
defective. Try installing a new telephone line cord.
• If changing telephone line cord does not help, the wall jack (or the wiring to this wall jack) may be
defective. Contact your telephone service provider.
• You may be using a new cable or VoIP service, the existing telephone jacks in your home may no
longer work. Contact your service provider for solutions.
The display shows To register HS... and ...see manual alternately. The handset does not
work at all.
• The handset is deregistered from the telephone base. Place the handset in the telephone base to
register it back. The handset shows Registered and you hear a beep when the registration process
completes. This process takes about 60 seconds to complete.
I have accidentally set my handset/telephone base LCD language to Spanish or French, and I
don’t know how to change it back to English.
• While the handset/telephone base is not in use, press MENU, then enter 364#.
• While the handset is on a call, press MENU, then enter 364#. The call ends.
The answering system does not record messages.
• Make sure the answering system is on.
• Make sure the memory of the answering system is not full. When the answering machine memory
is full, it does not record new messages until some old messages are deleted.
• If you subscribe to voicemail service, change the number of ring so that your answering system
answers before your voicemail answers. To determine how many rings activate your voicemail,
contact your telephone service provider.
• If there is a fax machine connected to the same telephone line, try disconnecting the fax machine.
If that solves the problem, consult your fax machine documentation for information on compatibility
with answering systems.
Common cure for electronic equipment.
• If the telephone is not responding normally, put the cordless handset in the telephone base.
If this does not fix the problem, do the following (in the order listed):
. Disconnect the power to the telephone base.
2. Disconnect the battery on the cordless handset.
3. Wait a few minutes before connecting power to the telephone base.
4. Install the battery again and place the cordless handset in the handset charger.
5. Wait for the cordless handset to synchronize with the telephone base. Allow up to one minute
for this to take place.
13
Maintenance
Taking care of your telephone
Your cordless telephone contains sophisticated electronic parts, so it must be treated with care.
Avoid rough treatment
Place the handset down gently. Save the original packing materials to protect your telephone if you ever need
to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or handle it with
wet hands. Do not install the telephone base near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety,
take caution when using electrical appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a soft
cloth slightly dampened with water or mild soap. Do not use excess water or cleaning solvents of any kind.
Remember that electrical appliances can cause serious injury if used when you are wet or standing in water. If the
telephone base should fall into water, DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND
TELEPHONE LINE CORD FROM THE WALL. Then remove the telephone by the unplugged cords.
®
The RBRC seal
®
The RBRC seal on the nickel-metal hydride battery indicates that VTech Communications, Inc. is
voluntarily participating in an industry program to collect and recycle these batteries at the end of their
useful lives, when taken out of service within the United States and Canada.
®
The RBRC program provides a convenient alternative to placing used nickel-metal hydride
batteries into the trash or municipal waste, which may be illegal in your area.
®
VTech’s participation in RBRC
makes it easy for you to drop off the spent battery at local retailers
®
participating in the RBRC program or at authorized VTech product service centers. Please call
1 (800) 8 BATTERY® for information on Ni-MH battery recycling and disposal bans/restrictions
in your area. VTech’s involvement in this program is part of its commitment to protecting our
environment and conserving natural resources.
®
RBRC and 1 (800) 8 BATTERY® are registered trademarks of the Rechargeable Battery
Recycling Corporation.
FCC, ACTA and IC regulations
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under Part
15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Privacy of communications may not be ensured when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely
absorbed by a user or bystander according to the intended usage of the product. This product has been tested and
found to comply with the FCC criteria. The handset may be safely held against the ear of the user. The telephone base
shall be installed and used such that parts of the user’s body other than the hands are maintained at a distance of
approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative
Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other
things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be provided to your telephone
service provider upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with
applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and modular plug
is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An
RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines. See the installation
instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone
line and still have them ring when you are called. The REN for this product is encoded as the 6th and 7th characters
following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all
RENs should be five (5.0) or less. For more information, please contact your telephone service provider.
This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected
to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have
questions about what will disable alarm equipment, consult your telephone service provider or a qualified installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected.
Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents. For repair
procedures, follow the instructions outlined under the Limited warranty.
If this equipment is causing harm to the telephone network, the telephone service provider may temporarily discontinue
your telephone service. The telephone service provider is required to notify you before interrupting service. If advance
notice is not practical, you will be notified as soon as possible. You will be given the opportunity to correct the problem
and the telephone service provider is required to inform you of your right to file a complaint with the FCC. Your
telephone service provider may make changes in its facilities, equipment, operation, or procedures that could affect the
proper functioning of this product. The telephone service provider is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers
(e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
Privacy of communications may not be ensured when using this telephone.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical
specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 1.0. The REN is an indication of the maximum
number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any
combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five.
This product meets the applicable Industry Canada technical specifications.
14
For C-UL compliance only
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de blessures corporelles ou d’électrocution, suivez toujours ces mesures
préventives de base lorsque vous utilisez votre téléphone :
.
Lisez et comprenez bien toutes les instructions.
2.
Observez toutes les instructions et mises en garde inscrites sur l’appareil.
3.
Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez pas de nettoyeurs liquides ni en
aérosol. N’utilisez qu’un chiffon doux et légèrement humecté.
4.
N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo, d’un évier de cuisine, d’un bac de
lavage ou d’une piscine, ou dans un sous-sol humide ou sous la douche.
5.
Ne déposez pas ce téléphone sur un chariot, support ou table chancelants. L’appareil pourrait tomber et être
sérieusement endommagé.
6.
Évitez d’installer le système téléphonique dans les endroits soumis à une température extrême, à la lumière
directe du soleil ou à proximité immédiate d’autres appareils électriques ou électroniques. Protégez votre
téléphone contre les sources d’humidité, la poussière, les vapeurs et les liquides corrosifs.
7.
Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées à l’arrière ou en dessous. Afin
d’empêcher la surchauffe, ces ouvertures ne doivent pas être obstruées en plaçant l’appareil sur un lit, divan,
tapis ou autre surface similaires. Ne placez pas cet appareil à proximité d’un élément de chauffage ni d’une
plinthe électrique. De plus, ne l’installez pas dans une unité murale ou un cabinet fermé qui ne possède pas
d’aération adéquate.
.
Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur les étiquettes de l’appareil. Si vous ne
connaissez pas le voltage de votre maison, consultez votre marchand ou votre fournisseur d’électricité.
9.
Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans un endroit sécuritaire, là où personne
ne pourra trébucher sur la ligne d’alimentation ni le cordon téléphonique modulaire.
0. N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car ils pourraient toucher à
des points de tension dangereux ou court-circuiter des pièces, ce qui constituerait un risque d’incendie ou
d’électrocution. N’échappez pas de liquides dans l’appareil.
. Afin de réduire les risques d’électrocution, ne démontez pas l’appareil, mais apportez-le plutôt à un centre de
service qualifié s’il doit être réparé. En enlevant le couvercle, vous vous exposez à des tensions dangereuses ou
autres dangers similaires. Un remontage inadéquat peut être à l’origine d’une électrocution lors d’une utilisation
ultérieure de l’appareil. Débranchez l’appareil avant de procéder au nettoyage. Utilisez un chiffon humide et
doux.
2. Ne surchargez pas les prises de courant et les rallonges.
3. Débranchez cet appareil de la prise de courant et communiquez avec le département de service à la clientèle
de VTech dans les cas suivants:
•
Lorsque le cordon d’alimentation est endommagé ou écorché.
•
Si du liquide a été échappé dans l’appareil.
•
Si l’appareil a été exposé à une source d’humidité telle que la pluie ou l’eau.
•
Si le produit ne fonctionne pas normalement en respectant les instructions de fonctionnement. Réglez
uniquement les commandes indiquées dans le les instructions de fonctionnement. Les réglages incorrects
des autres commandes pourraient provoquer un dommage qui pourrait exiger un travail exhaustif de la
part d’un technicien autorisé afin de rétablir le fonctionnement normal de l’appareil.
•
Si le produit a été échappé et que le socle et/ou le combiné a été endommagé.
•
Si le produit affiche une nette diminution de sa performance.
14. Évitez d’utiliser un téléphone (autre qu’un sans fil) pendant un orage. Les éclairs peuvent être à l’origine d’une
électrocution.
15. N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de la fuite. En certaines circonstances,
une flammèche pourrait être provoquée lorsque l’adaptateur est branché à une prise de courant, ou lorsque
le combiné est déposé sur le socle. Ceci est un événement commun associé à la fermeture d’un circuit
électrique. L’utilisateur ne devrait pas brancher le téléphone à une prise de courant, et ne devrait pas
déposer le combiné chargé sur le socle, si le téléphone se trouve à proximité d’un endroit comportant des
concentrations de gaz inflammables, à moins que la ventilation soit adéquate. Une flammèche dans un tel
endroit pourrait provoquer un incendie ou une explosion. De tels environnements peuvent comprendre: des
endroits où l’on utilise de l’oxygène médical sans ventilation adéquate; des gaz industriels (dissolvants de
nettoyage, des vapeurs d’essence, etc.); une fuite de gaz naturel, etc.
16. Ne placez que le combiné de votre téléphone près de votre oreille lorsqu’en mode de conversation.
17. Ces adaptateurs ont été conçus pour être orientés en position verticale ou montés au sol. Les broches ne
sont pas conçues pour maintenir l’adaptateur en place si celui-ci est barnché dans une prise au plafond ou
sous une table/ armoire.
CONSERVEZ CES INSTRUCTIONS
Pile
•
MISE EN GARDE : Risque d’explosion si la pile est remplacée par une pile de types incorrects. Jetez les piles
épuisées en respectant les instructions.
•
Ne jetez pas la pile au feu. Vérifiez les instructions spécifiques de mise aux rebus auprès des autorités locales.
•
N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en échapperait est corrosif et pourrait causer des brûlures
ou des blessures aux yeux ou à la peau. L’électrolyte est toxique si avalé.
•
Soyez prudents lorsque vous manipulez les piles afin d’éviter les courts-circuits provoqués par des matériaux
conducteurs.
•
Rechargez la pile incluse avec cet appareil, selon les instructions et limites spécifiées dans ce guide d’utilisation.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (s’applique uniquement aux téléphones numériques sans fil):
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante, a mené une
évaluation pluridisciplinaire des interférences entre les téléphones sans fil portatifs et les stimulateurs cardiaques
implantés dans l’organisme. Appuyée par l’Administration des aliments et drogues (FDA) des États-Unis, la firme WTR
recommande aux médecins:
Avis aux détenteurs de stimulateurs cardiaques
•
Ils doivent tenir le téléphone sans fil à une distance d’au moins six pouces du stimulateur cardiaque.
•
Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de
chemise, lorsque celui-ci est en marche.
•
Ils doivent utiliser le téléphone sans fil en l’appuyant sur l’oreille qui se trouve dans la direction opposée au
stimulateur cardiaque.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de simulateurs cardiaques
causés par les gens qui utilisent un téléphone sans fil à proximité de ceux-ci.
À propos des téléphones sans fil
•
Alimentation électrique: Les mêmes caractéristiques qui constituent des avantages pour les téléphones sans fil
affichent également des restrictions. Les appels téléphoniques sont transmis entre le combiné sans fil et le socle par
le biais d’ondes radio ; il y a donc la possibilité que vos conversations téléphoniques sans fil soient interceptées par
des équipements de réception radio se trouvant dans la portée du combiné sans fil. Pour cette raison, vous ne devez
pas percevoir les communications téléphoniques sans fil comme étant aussi confidentielles.
•
Alimentation électrique: Le socle de ce téléphone sans fil doit être branché à une prise électrique fonctionnelle.
La prise électrique ne doit pas être contrôlée par un interrupteur mural. Les appels ne pourront pas être effectués
du combiné sans fil si le socle est débranché ou mis hors tension ou si le courant est coupé.
•
Possibilité d’interférences aux téléviseurs: Certains téléphones sans fil fonctionnent sur des fréquences pouvant
causer des interférences aux téléviseurs et aux magnétoscopes. Pour réduire ou prévenir de telles interférences, ne
placez pas le socle du téléphone sans fil près ou sur un téléviseur ou magnétoscope. S’il y a présence de parasites,
il est conseillé d’éloigner le téléphone sans fil du téléviseur ou du magnétoscope afin de réduire possiblement les
interférences.
•
Piles rechargeables: Manipulez les piles avec soin afin de ne pas les court-circuiter avec des bagues, bracelets
ou clés. Les piles ou le conducteur peut surchauffer et causer des blessures. Respectez la polarité adéquate entre
la pile et le chargeur.
•
Les bloc-piles rechargeables à l’hydrure métallique de nickel: Jetez ces blocs-piles de manière écologique et
sécuritaire. Ne les incinérez pas et ne les percez pas. Tel que les autres piles de ce type, elles pourraient dégager
une matière toxique qui peut causer des blessures corporelles si elles sont brûlées ou percées.
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”)
that the Product and all accessories provided in the sales package (“Product”) are free from defects in material and
workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with
the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and
used in the United States of America and Canada.
15
What will VTech do if the Product is not free from defects in materials and workmanship during the limited
warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option,
without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement
parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar
design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTech’s option,
is your exclusive remedy. VTech will return the repaired or replacement Products to you in working condition. You
should expect the repair or replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or
replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the
repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is
shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer.
Register online to get an additional 3-month warranty!
What is not covered by this limited warranty?
This limited warranty does not cover:
. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation,
abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration or modification by anyone other than an authorized
service representative of VTech; or
3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or
antenna systems; or
4. Product to the extent that the problem is caused by use with non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been
removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or
used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or
7. Product returned without a valid proof of purchase (see item 2 below); or
. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.
How do you get warranty service?
To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call
1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and features may
save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are
responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return
repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech
assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or
proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the
cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of
Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service?
. Return the entire original package and contents including the Product to the VTech service location along with a
description of the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date
of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral
communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively
describes all of VTech’s responsibilities regarding the Product. There are no other express warranties.
No one is authorized to make modifications to this limited warranty and you should not rely on any such modification.
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights, which
vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten
warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/provinces
do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event
shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited
to lost profits or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment,
and claims by third parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
Technical specifications
Frequency control
Crystal controlled PLL synthesizer
Transmit frequency
DECT frequency: 1921.536-1928.448 MHz
Bluetooth frequency: 2402.000-2480.000 MHz
Channels
DECT channel: 5
Bluetooth channel: 79
Nominal effective
range
Maximum power allowed by FCC and IC. Actual operating range may vary
according to environmental conditions at the time of use.
Power requirements
Handset: 2.4V Ni-MH battery
Telephone base: 6V DC @ 400mA
Charger: 6V AC @ 300mA
Memory
Directory: 200 memory locations; up to 30 digits and 15 characters
Caller ID log: 50 memory locations; up to 24 digits and 15 characters
Compatible with
Hearing Aid T-Coil
Telephones identified with this logo have reduced noise and interference when
used with most T-coil equipped hearing aids and cochlear implants. The TIA-1083
Compliant Logo is a trademark of the Telecommunications Industry Association.
Used under license.
T
TIA-1083
®
The Bluetooth word mark and logos are owned by Bluetooth SIG, Inc. and any use of such
marks by VTech Holdings Limited is under license. VTech Holdings Limited is a member of
Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners.
Specification are subject to change without notice.
© 2014 VTech Communications, Inc.
All rights reserved. 12/14. DS6751-X_ACIB_V5.0
Document order number: 91-007247-050-100
16