advertisement
CT-5611T
ADSL2+ Combo Router
User Manual
Version A1.4, October 3, 2007
261070-011
Preface
This manual provides information related to the installation, operation, and application of this device. The individual reading this manual is presumed to have a basic understanding of telecommunications terminology and concepts.
If you find the product to be inoperable or malfunctioning, please contact technical support for immediate service by email at [email protected]
For product update, new product release, manual revision, or software upgrades, please visit our website at http://www.comtrend.com
Important Safety Instructions
With reference to unpacking, installation, use and maintenance of your electronic device, the following basic guidelines are recommended:
• Do not use or install this product near water, to avoid fire or shock hazard. For example, near a bathtub, kitchen sink or laundry tub, or near a swimming pool.
Also, do not expose the equipment to rain or damp areas (e.g. a wet basement).
• Do not connect the power supply cord on elevated surfaces. Allow it to lie freely.
There should be no obstructions in its path and no heavy items should be placed on the cord. In addition, do not walk on, step on or mistreat the cord.
• Use only the power cord and adapter that are shipped with this device.
• To safeguard the equipment against overheating, make sure that all openings in the unit that offer exposure to air are not blocked.
• Avoid using a telephone (other than a cordless type) during an electrical storm.
There may be a remote risk of electric shock from lightening. Also, do not use the telephone to report a gas leak in the vicinity of the leak.
• Never install telephone wiring during stormy weather conditions.
CAUTION:
• To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.
• Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.
WARNING
Disconnect the power line from the device before servicing.
Power supply specifications are clearly stated in Appendix B .
Copyright
Copyright©2008 Comtrend Corporation. All rights reserved. The information contained herein is proprietary to Comtrend Corporation. No part of this document may be translated, transcribed, reproduced, in any form, or by any means without prior written consent of Comtrend Corporation.
NOTE: This document is subject to change without notice.
1
Table of Contents
.................................................................................. 8
2.2 USB D EVICE D RIVER A UTO RUN I NSTALLATION ................................................ 9
OS) ............................................ 11
.................................................................... 17
CHAPTER 3 LOGIN VIA THE WEB BROWSER................................................ 21
............................................................................................ 22
........................................................................................... 37
5.2.1 PPP over ATM (PPPoA) and PPP over Ethernet (PPPoE) ..................... 39
5.2.2 MAC Encapsulation Routing (MER) ........................................................ 44
2
.............................................................................................. 89
........................................................................................... 93
3
Chapter 1 Introduction
The CT-5611T ADSL2+ compact and high performance combo router provides one
10/100 Ethernet Interface and one USB interface, offering ADSL connectivity at speeds of up to 24 Mbps. It also has full routing capabilities to segment/route IP protocol, and supports advanced security functions.
1.1 Features
• IP filtering
• SPI (Stateful Packet Inspection)
• DoS protection
• Static route
• Dynamic IP assignment
• NAT/PAT
• IGMP Proxy
• DHCP Server/Relay/Client
• DNS Proxy
• Auto PVC configuration
• Up to 8 VCs
• Web-based management Remote configuration and upgrade
• Configuration backup and restoration
• FTP/TFTP server
• TR-68
• TR-69
4
1.2 Application
The following diagram depicts the application of the CT-5611T.
5
1.3 Front Panel LED Indicators
The front panel LEDs are shown in the picture below, followed by an explanation in the table below.
LED
POWER
ADSL LINK
Color Mode Function
Green
Red
On
Off
On
The router is powered up.
The router is powered down.
POST (Power On Self Test) fail (not bootable) or router failure which could be any error of internal sequence or state that will not allow the router to connect to the DSLAM, or send data.
Green
Green
On
Off
Blink
The ADSL link is established.
The ADSL link is not established.
The ADSL link is training or some traffic is passing through ADSL.
6
USB
INTERNET
Green
Green
Green
Green
Red
LAN
Green
Green
On
Off
Blink
On
Off
Blink
On
On
Off
Blink
A USB link is established.
A USB link is not established.
Data transmitting or receiving over USB.
Normal operating status.
The ADSL link is terminated.
Data transmitting or receiving over ADSL.
Device attempted to become IP connected and failed (no DHCP response, no PPPoE response, PPPoE authentication failed, no
IP address from IPCP, etc.)
For bridged mode, the indicator light is off.
If the IP or PPPoE session is dropped due to an idle timeout, the light will remain green if an ADSL connection is still present. If the session is dropped for any other reason, the light is turned off. The light will turn red when it attempts to reconnect and DHCP or PPPoE fails.
An Ethernet Link is established.
An Ethernet Link is not established.
Data transmitting or receiving over LAN.
7
Chapter 2 Installation
2.1 Hardware Installation
Follow the instructions below to complete the hardware connections.
Connection to LINE port
Reset Button
If you wish to connect both the router and a telephone, connect the LINE port to a
POTS splitter with a RJ11 connection cable.
Connection to LAN port
To connect to a hub or PC, use a RJ45 cable. The port is auto-sensing MDI/X and either straight-through cable or crossover cable can be used.
Connection to USB port
Connect the USB port to a PC with a standard USB cable.
Connection to Power
Connect the Power jack to the shipped power cord. Attach the power adapter to the wall outlet or other AC source.
After all connections have been made, turn the power-switch to the on position. After powering on, the router performs a self-test. Wait for a few seconds until the test is finished, then the router will be ready to operate.
Reset Button
Restore the default parameters of the router by holding down the device’s Reset button until the LED’s start blinking simultaneously (about 5 seconds). After the device has rebooted successfully, and if the connection is established, the LAN LED, ADSL LED or
USB LED will display in green, depending on the connection type.
Caution 1: If the router fails to power up, or it malfunctions, first verify that the power supply is connected correctly. Then power it on again. If the problem persists, contact our technical support engineers.
Caution 2: Before servicing or disassembling this equipment always disconnect all power cords and telephone lines from the wall outlet.
8
2.2 USB Device Driver Auto-run Installation
Before you connect your router’s USB cable to your PC, you must load the ADSL USB drivers. The auto-run USB driver installation supports Win ME, Win 98, Win 2000,
Win XP (32 bit) and Vista (32 bit). For those using Windows XP 64 bit, the driver needs to be installed manually (please see section 2.3 below for details), and the driver is also enclosed on the CD-ROM.
To connect the router to a PC using the USB interface, you need to use a standard
USB cable and install the USB interface software. Follow the steps below:
STEP 1: Insert the Installation disk and the following screen will be displayed. Click the Next button to continue.
STEP 2: When the screen displays as below, wait until the drivers are fully installed.
9
STEP 3: Click the Finish button, when the screen displays as below.
STEP 4: Installation is complete.
10
2.3 USB Driver Manual Installation(64bit OS)
Before you connect your router’s USB cable to your PC, you must load the ADSL USB drivers. This manual USB driver installation supports Windows XP 64 bit.
To connect the router to a PC using the USB interface, you need to use a standard
USB cable and install the USB interface software. Follow the steps below:
STEP 1: Connect the USB router to the PC by plugging the flat connector of a standard USB cable into your PC, and plugging the square connector into the router. The screen will display as below:
STEP 2: When the screen displays as below, select install from a list of specific
location (Advanced) and click the Next button.
11
Note: This screen won’t be displayed if the USB Driver has been previously un/installed.
STEP 3: If you are installing the software from a disk, insert the disk.
12
STEP 4: Select the location of the file using the Browse button. Normally, the file is on the CD-ROM shipped with the device.
STEP 5: Locate the Vista folder, and click the OK button.
13
STEP 6: When the screen displays as below, click the NEXT button.
14
15
STEP 7: Click the Finish button, when the screen displays as below.
STEP 8: Installation is complete.
16
2.4 Un-installing the USB Driver
STEP 1: Click Start, Settings and then Control Panel as shown here.
STEP 2: When the following screen is displayed, click on the Add/Remove Hardware
Icon.
STEP 3: When the following screen is displayed, click Next.
17
STEP 4: When the following screen is displayed, select Uninstall/Unplug a device
(as shown here). Then, click Next.
STEP 5: When the following screen is displayed, select Uninstall a device (as shown here). Then, click Next.
18
STEP 6: When the following screen is displayed, select the device that you want to uninstall. Then, click Next.
19
STEP 7: When the following screen is displayed, click Next to confirm that you want to uninstall the device.
STEP 8: When the following screen is displayed, click Finish as un-installation is complete.
20
Chapter 3 Login via the Web Browser
This section describes how to manage the router via a Web browser via the remote end. You can use a web browser such as Microsoft Internet Explorer, or Netscape
Navigator. (The Web page is best viewed with Microsoft Internet Explorer 5.0 and later): A unique default user account is assigned with user name admin and password tot. The user can change the default password later when logged in to the device.
3.1 IP Address
The default IP address of the CT-5611T (LAN port) is 192.168.1.1. To configure the
CT-5611T for the first time, the configuration PC must have a static IP address within the 192.168.1.x subnet. Follow the steps below to configure your PC IP address to use subnet 192.168.1.x.
STEP 1: Right click on the Local Area Connection under the Network and Dial-Up connection window and select Properties.
STEP 2: Enter the TCP/IP screen and change the IP address to the domain of
192.168.1.x/24.
STEP 3: Click OK to submit the settings.
STEP 4: Start your Internet browser with the default IP address 192.168.1.1.
21
3.2 Login Procedure
Perform the following steps to bring up the Web user interface and configure the CT-
5611T. To log on to the system from the Web browser, follow the steps below:
STEP 1: Start your Internet browser. Type the IP address for the router in the Web address field. For example, if the IP address is 192.168.1.1, type
http://192.168.1.1
STEP 2: You will be prompted to enter your user name and password. Type admin in the user name field and tot in the password field, and click OK. These values can be changed later in the Web User Interface by selecting the
Management link.
STEP 3: After successfully logging in, you will reach the Quick Setup menu.
Here is the Device Info screen for your reference.
22
23
3.3 Default Settings
During power on initialization, the CT-5611T initializes all configuration attributes to default values. It will then read the configuration profile from the Permanent
Storage section on the flash memory. The default attributes are overridden when identical attributes with different values are configured. The configuration profile in
Permanent Storage can be created via the Web user interface, the console, or telnet user interface, or other management protocols. The factory default configuration can be restored either by pushing the reset button for more than five seconds, or by clicking the Restore Default Configuration option in the Restore Settings screen.
The following default settings are present when setting up the router for the first time. The PC running the browser can be attached to the Ethernet or the USB. z z z z z z z z z z z
LAN port IP address: 192.168.1.1
Local administrator account name: admin
Local administrator account password: tot
Local non- administrator account name: user
Local non- administrator account password: user
Remote WAN access: disabled
Remote WAN access account name: support/support
Remote WAN access account password: support/support
NAT and firewall: disabled
DHCP server on LAN interface: enable
WAN IP address: none
24
Chapter 4 Quick Setup
After login, the Quick Setup screen appears as shown.
Note: The selections available on the left side of menu are based upon the configured connection.
25
4.1 WAN
Click Device Info on the menu bar to display the WAN option. Then, click WAN on the Device Info menu bar to display the configured PVC(s) and the status.
VPI/VCI
Con. ID
Category
Service
Interface
Protocol
IGMP
Nat
QoS
State
Status
IP Address
Shows the values of the ATM VPI/VCI
Shows the connection ID
Shows the ATM service classes
Shows the name for WAN connection
Shows connection interfaces
Shows the connection type, such as PPPoE, PPPoA, etc.
Shows the statue of the IGMP function
Shows if the Network Address Translation(NAT) is enabled or disabled.
Shows if QoS is enabled or disabled
Shows the connection state of the WAN connection
Lists the status of DSL link
Shows IP address for WAN interface
26
4.2 Statistics
Selection of the Statistics screen provides statistics for the Network Interface of LAN,
WAN, ATM and ADSL. All statistics screens are updated every 15 seconds.
27
The Network Statistics screen shows interface statistics for Ethernet and USB interfaces. (The Network Statistics screen shows interface statistics for LAN of
Ethernet and USB interfaces. This shows byte transfer, packet transfer, Error and
Drop statistics for the LAN interface.)
28
The following figure shows the WAN statistics screen.
Service
VPI/VCI
Protocol
Received/Transmitted
Bytes -
Pkts -
Errs -
Drops -
Shows the service type
Shows the values of the ATM VPI/VCI
Shows the connection type, such as PPPoE,
PPPoA, etc.
Rx/TX (receive/transmit) packet in Byte
Rx/TX (receive/transmit) packets
Rx/TX (receive/transmit) the packets which are errors,
Rx/TX (receive/transmit) the packets which are dropped
29
The following figure shows the ATM statistics screen.
ATM Interface Statistics
Field Description
In Octets Number of received octets over the interface
Out Octets
Number of transmitted octets over the interface
In Errors
In Unknown
In Idle Cells
In Circuit Type Errors
In Oam RM CRC Errors
In GFC Errors
Number of cells dropped due to uncorrectable HEC errors
Number of received cells discarded during cell header validation, including cells with unrecognized VPI/VCI values, and cells with invalid cell header patterns. If cells with undefined PTI values are discarded, they are
In Hec Errors also counted here.
Number of cells received with an ATM Cell Header HEX error
In Invalid Vpi Vci Errors Number of cells received with an unregistered VCC address.
In Port Not Enabled Errors Number of cells received on a port that has not been enabled.
In PTI Errors Number of cells received with an ATM header Payload
Type Indicator (PTI) error
Number of idle cells received
Number of cells received with an illegal circuit type
Number of OAM and RM cells received with CRC errors
Number of cells received with a non-zero GFC.
30
ATM AAL5 Layer Statistics over ADSL interface
Field Description
In Octets Number of received AAL5/AAL0 CPCS PDU octets
Out Octets Number of received AAL5/AAL0 CPCS PDUs octets transmitted
In Ucst Pkts
Out Ucast Pkts
In Errors
Out Errors
Number of received AAL5/AAL0 CPCS PDUs passed to a higher-layer for transmission
Number of received AAL5/AAL0 CPCS PDUs received from a higher layer for transmissions
Number of received AAL5/AAL0 CPCS PDUs received that contain an error. The types of errors counted include CRC-
32 errors.
Number of received AAL5/AAL0 CPCS PDUs that could be transmitted due to errors.
In Discards Number of received AAL5/AAL0 CPCS PDUs discarded due to an input buffer overflow condition.
This field is not currently used Out Discards
ATM AAL5 LAYER STATISTICS FOR EACH VCC OVER ADSL INTERFACE
Field Descriptions
CRC Errors
SAR TimeOuts
Number of PDUs received with CRC-32 errors
Number of partially re-assembled PDUs, which were discarded because they were not fully re-assembled within the required period of time. If the re-assembly time is not supported then, this object contains a zero value.
Over Sized SDUs Number of PDUs discarded because the corresponding SDU was too large
Short Packets Errors Number of PDUs discarded because the PDU length was less than the size of the AAL5 trailer
Length Errors Number of PDUs discarded because the PDU length did not match the length in the AAL5 trailer
31
The following figure shows the ADSL Network Statistics screen. Within the ADSL
Statistics window, a bit Error Rate Test can be started using the ADSL BER Test button. The Reset button resets the statistics.
32
Field Description
Mode Modulation protocol G.dmt, G.lite, T1.413, ADSL2,
ADSL2+
Type
Line Coding
Channel type Interleave or Fast
Trellis On/Off
Status
Link Power State
SNR Margin (dB)
Attenuation (dB)
Lists the status of the DSL link
Link output power state.
Signal to Noise Ratio (SNR) margin
Estimate of average loop attenuation in the downstream direction.
Output Power (dBm)
Attainable Rate (Kbps)
Rate (Kbps)
Super Frames
Total upstream output power
The sync rate you would obtain.
Current sync rate.
Total number of super frames
Super Frame Errors
RS Words
Number of super frames received with errors
Total number of Reed-Solomon code errors
RS Correctable Errors Total Number of RS with correctable errors
RS Uncorrectable Errors Total Number of RS words with uncorrectable errors
HEC Errors
OCD Errors
LCD Errors
Total ES:
Total SES:
Total UAS:
Total Number of Header Error Checksum errors
Total Number of out-of-cell Delineation errors
Total number of Loss of Cell Delineation
Total Number of Errored Seconds
Total Number of Severely Errored Seconds
Total Number of Unavailable Seconds
33
4.3 Route
Choose Route to display the routes that the route information has learned.
4.4 ARP
Click ARP to display the ARP information.
34
4.5 DHCP
Click DHCP to display the DHCP information.
35
Chapter 5 Quick Setup
The Quick Setup allows the user to configure the ADSL router for DSL connectivity and Internet access. It also guides the user though the WAN network setup first and then the LAN interface setup. You can either manually customize the router or follow the online instruction to set up the router.
The CT-5611T ADSL router supports the following five network operating modes over an ATM PVC WAN interface.
PPP over Ethernet (PPPoE)
PPP over ATM (PPPoA)
MAC Encapsulated Routing (MER)
IP over ATM (IPoA)
Bridging
The following configuration considerations apply:
The WAN network operating mode operation depends on the service provider’s configuration on the Central Office side and Broadband Access Server for the PVC
If the service provider provides PPPoE service, then the connection selection depends on whether the LAN-side device (typically a PC) is running a PPPoE client or whether the CT-5611T is to run the PPPoE client. The CT-5611T can support both cases simultaneously.
If some or none of the LAN-side devices do not run PPPoE client, then select PPPoE.
If every LAN-side device is running a PPPoE client, then select Bridge In PPPoE mode,
CT-5611T also supports pass-through PPPoE sessions from the LAN side while simultaneously running a PPPoE client fro non-PPPoE LAN devices.
NAPT and firewall are always enabled when PPPoE mode is selected, but they can be enabled or disabled by the user when MER or IPoA is selected, NAPT and firewall are always disabled when Bridge mode is selected.
Depending on the network operating mode, and whether NAPT and firewall are enabled or disabled, the main panel will display or hide the NAPT/Firewall menu. For instance, at initial setup, the default network operating mode is Bridge. The main panel will not show the NAPT and Firewall menu.
Note: Up to eight PVC profiles can be configured and saved on the flash memory.
To activate a particular PVC profile, you need to navigate all the Quick Setup pages until the last summary page, then click on the Finish button and reboot the system.
36
5.1 Auto Quick Setup
The auto quick setup requires the ADSL link to be up. The ADSL router will automatically detect the PVC. You only need to follow the online instructions that you are prompted.
1. Select Quick Setup to display the DSL Quick Setup screen.
2. Click Next to start the setup process. Follow the online instructions to complete the setting. This procedure will skip some processes like PVC index, or encapsulation.
3. After the settings are complete, you can use the ADSL service.
5.2 Manual Quick Setup
STEP 1: Click Quick Setup and un-tick the DSL Auto-connect checkbox to enable manual configuration of the connection type.
Un-tick this checkbox to enable manual setup and display the following screen.
37
STEP 2: Enter the Virtual Path Identifier (VPI) and Virtual Channel Identifier (VCI).
Select Enable Quality Of Service if required. Click Next.
STEP 3: Then, choose the Encapsulation mode.
STEP 4: Choosing different connection types pops up different settings requests.
Enter appropriate settings that are requested by your service provider. The following descriptions state each connection type setup separately. Select Enable 802.1q (by ticking the box) if required, and input a number for the VLAN ID. Click on “Next” to go to next step.
38
5.2.1 PPP over ATM (PPPoA) and PPP over Ethernet (PPPoE)
1. Select the PPP over ATM (PPPoA) or PPP over Ethernet (PPPoE) radio button and click Next. The following screen appears:
PPP USERNAME/PPP PASSWORD
The PPP Username and the PPP password requirement are dependent on the particular requirements of the ISP or the ADSL service provider. The WEB user interface allows a maximum of 256 characters in the PPP user name and a maximum of 32 characters in PPP password.
Authentication Method
Choose from AUTO, PAP, CHAP and MSCHAP.
Encapsulation Mode
Choosing different connection types provides different encapsulation modes. z z z z z
PPPoA- VC/MUX, LLC/ENCAPSULATION
PPPoE- LLC/SNAP BRIDGING, VC/MUX
MER- LLC/SNAP-BRIDGING, VC/MUX
IPoA- LLC/SNAP-ROUTING, VC MUX
Bridging- LLC/SNAP-BRIDGING, VC/MUX
39
Disconnect if no activity
The CT-5611T can be configured to disconnect if there is no activity for a period of time by selecting the Dial on demand check box. When the checkbox is ticked, you need to enter the inactivity timeout period. The timeout period ranges from 1 minute to 4320 minutes.
PPP IP Extension
The PPP IP Extension is a special feature deployed by some service providers. Unless your service provider specially requires this setup, do not select it.
The PPP IP Extension supports the following conditions: z
Allows only one PC on the LAN z z z z z
The public IP address assigned by the remote side using the PPP/IPCP protocol is actually not used on the WAN PPP interface. Instead, it is forwarded to the
PC’s LAN interface through DHCP. Only one PC on the LAN can be connected to the remote, since the DHCP server within the ADSL router has a single IP address to assign to a LAN device.
NAPT and firewall are disabled when this option is selected.
The ADSL router becomes the default gateway and DNS server to the PC through DHCP using the LAN interface IP address.
The ADSL router extends the IP subnet at the remote service provider to the
LAN PC. That is, the PC becomes a host belonging to the same IP subnet.
The ADSL router bridges the IP packets between WAN and LAN ports, unless the packet is addressed to the router’s LAN IP address.
Enable NAT checkbox
If the LAN is configured with a private IP address, the user should select this checkbox. The NAT submenu on the left side main panel will be displayed after reboot. The user can then configure NAT-related features after the system comes up.
If a private IP address is not used on the LAN side (i.e. the LAN side is using a public
IP), this checkbox should be de-selected. When the system comes back after reboot, the NAT submenu will not be displayed on the left main panel.
Enable Firewall
The Internet has made large amounts of information available to the average computer user at home, in business and in education. For many people, having access to this information is no longer just an advantage, it is essential. Yet connecting a private network to the Internet can expose critical or confidential data to malicious attack from anywhere in the world. Users who connect their computers to the Internet must be aware of these dangers, their implications and how to protect their data and their critical systems. Firewalls can protect both individual computers and corporate networks from hostile intrusion from the Internet, but must be understood to be used correctly.
40
Use Static IP Address
Unless your service provider specially requires this setup, do not select it.
If selected, enter your static IP address.
MTU
This option allows us to change the MTU size for WAN interface, PPPoE and PPPoA. The default value is 1492 for PPPoE and 1500 for PPPoA.
2. Click Next to display the screen below.
Enable IGMP Multicast checkbox: Tick the checkbox to enable IGMP multicast
(proxy). IGMP (Internet Group Membership Protocol) is a protocol used by IP hosts to report their multicast group memberships to any immediately neighboring multicast routers.
Enable WAN Service checkbox: Tick this item to enable the ATM service. Untick it to stop the ATM service.
Service Name: This is user-defined.
41
3. After entering your settings, select Next. The following screen appears. The
Device Setup page allows the user to configure the LAN interface IP address, subnet mask and DHCP server. If the user would like this ADSL router to assign dynamic IP addresses, DNS server and default gateway to other LAN devices, select the radio box Enable DHCP server on the LAN to enter the starting IP address and end IP address and DHCP lease time. This configures the router to automatically assign IP addresses, default gateway address and DNS server addresses to each of your PCs.
Note 1: Enable DHCP Server Relay will not display if NAT is enabled in the previous step.
Note 2: The router’s default IP address is 192.168.1.1 and the default private address range provided by the ISP server in the router is 192.168.1.2 through
192.168.1.254.
Select Enable DHCP Server Relay (if required), and enter the DHCP Server IP
Address. This allows the router to relay the DHCP packets to the remote DHCP server.
The remote DHCP server will provide the IP address.
To configure a secondary IP address for the LAN port, click the box as shown below.
42
4. Click Next to display the WAN Setup-Summary screen that presents the entire configuration summary. Click Save/Reboot if the settings are correct. Click Back if you wish to modify the settings.
5. After clicking Save/Reboot, the router will save the configuration to the flash memory, and reboot. The Web UI will not respond until the system is brought up again. After the system is up, the Web UI will refresh to the Device Info page automatically. The CT-5611T is ready for operation and the LEDs display as described in the LED description tables.
43
5.2.2 MAC Encapsulation Routing (MER)
To configure MER, do the following.
1. Select Quick Setup and click Next.
2. Enter the PVC Index provided by the ISP and click Next and click Next
3. Select the MAC Encapsulation Routing (MER) radio button, and click Next. The following screen appears.
Enter information provided to you by your ISP to configure the WAN IP settings.
Notice: DHCP Client can be enabled for PVC in MER mode if Obtain an IP address
automatically is chosen. Changing the default gateway or the DNS effects the whole system. Configuring them with static values will disable the automatic assignment from DHCP or other WAN connection.
If you configure static default gateway over this PVC in MER mode, you must enter the IP address of the remote gateway in the "Use IP address". The "Use WAN interface" is optional.
The ISP should provide the values that must be entered in the entry fields.
44
4. Click Next to display the following screen appears.
Enable NAT checkbox: If the LAN is configured with a private IP address, the user should select this checkbox. The NAT submenu on the left side main panel will be displayed after reboot. The user can then configure NAT-related features after the system comes up. If a private IP address is not used on the LAN side (i.e the LAN side is using a public IP), this checkbox should be de-selected. When the system comes back after reboot, the NAT submenu will not be displayed on the left main panel. The default setting for Mer is disabled.
Enable Firewall checkbox: If the firewall checkbox is selected, the security submenu on the left side main panel will be displayed after system reboot. The user can then configure firewall features after the system comes up. If firewall is not used, this checkbox should be de-selected to free up system resources for better performance. When system comes back after reboot, the Security submenu will not be displayed on the left main panel. The default setting for Mer is disabled.
Enable IGMP Multicast: Tick the checkbox to enable IGMP multicast (proxy). IGMP
(Internet Group Membership Protocol) is a protocol used by IP hosts to report their multicast group memberships to any immediately neighboring multicast routers.
Enable WAN Service: Tick the checkbox to enable the WAN (ADSL) service. If this item is not selected, you will not be able to use the ADSL service.
Service Name: This is User-defined.
45
5. Upon completion, click Next. The following screen appears.
Note: If the NAT function is enabled, this DHCP Server Relay won’t be displayed as an option.
The Device Setup page allows the user to configure the LAN interface IP address and
DHCP server. If the user would like this ADSL router to assign dynamic IP addresses, DNS server and default gateway to other LAN devices, select the radio box Enable DHCP server on the LAN to enter the starting IP address and end IP address and DHCP lease time. This configures the router to automatically assign IP addresses, default gateway address and DNS server addresses to each of your PCs.
Note that the router’s default IP address is 192.168.1.1 and the default private address range provided by the ISP server in the router is 192.168.1.2 through
192.168.1.254.
Select Enable DHCP Server Relay (if required), and enter the DHCP Server IP
Address.
Note: Ethernet and USB interfaces (and the wireless LAN interface on the CT-
5611T) share the same subnet since they are bridged within the router.
If the NAT function is enabled, this DHCP Server Relay won’t be displayed as an option.
46
6. After entering your settings, select Next to display the following screen. The
WAN Setup-Summary screen presents the entire configuration summary. Click
Save/Reboot if the settings are correct. Click Back if you wish to modify the settings.
The following screen will be displayed.
After clicking Save/Reboot, the router will save the configuration to the flash memory, and reboot. The Web UI will not respond until the system is brought up again. After the system is up, the Web UI will refresh to the Device Info page automatically. The CT-5611T is ready for operation and the LEDs display as described in the LED description tables.
47
To configure IP Over ATM,
1. Select Quick Setup and click Next.
2. Enter the PVC Index and click Next.
3. Type the VPI and VCI values provided by the ISP and click Next.
4. Select the IP over ATM (IPoA) radio button and click Next. The following screen appears.
Notice that DHCP is not supported over IPoA. The user must enter the IP address or
WAN interface for the default gateway setup, and the DNS server addresses provided by the ISP.
5. Click Next. The following screen appears.
48
Enable NAT checkbox
If the LAN is configured with a private IP address, the user should select this checkbox. The NAT submenu on the left side main panel will be displayed after reboot. The user can then configure NAT-related features after the system comes up. If a private IP address is not used on the LAN side (i.e the LAN side is using a public IP), this checkbox should be de-selected. When the system comes back after reboot, the NAT submenu will not be displayed on the left main panel. The default setting for Mer is disabled.
Enable Firewall checkbox
If the firewall checkbox is selected, the security submenu on the left side main panel will be displayed after system reboot. The user can then configure firewall features after the system comes up. If firewall is not used, this checkbox should be deselected to free up system resources for better performance. When system comes back after reboot, the Security submenu will not be displayed on the left main panel.
The default setting for Mer is disabled.
Enable Quality Of Service
Enabling IP QoS for a PVC improves performance for selected classes of applications.
However, since IP QoS also consumes system resources, the number of PVCs will be reduced consequently. Use Advanced Setup/Quality of Service to assign priorities for the applications.
6. Click Next to display the following screen. The Device Setup page allows the user to configure the LAN interface IP address and DHCP server if the user would like this ADSL router to assign dynamic IP addresses, DNS server and default gateway to other LAN devices. Select the button Enable DHCP server on the LAN to enter the starting IP address and end IP address and DHCP lease time.
49
The user must configure the IP Address and the Subnet Mask. To use the DHCP service on the LAN, select the Enable DHCP server checkbox, and enter the Start
IP addresses, the End IP address and DHCP lease time. This configures the router to automatically assign IP addresses, default gateway address and DNS server addresses to each of your PCs.
Select Enable DHCP Server Relay (if required), and enter the DHCP Server IP
Address.
Note that the router’s default IP address is 192.168.1.1 and the default private address range provided by ISP server in the router is 192.168.1.2 through
192.168.1.254.
7. The WAN Setup-Summary screen presents the entire configuration summary.
Click Save/Reboot if the settings are correct. Click Back if you wish to modify the settings.
The following screen will be displayed.
50
8. After clicking Save/Reboot, the router will save the configuration to the flash memory, and reboot. The Web UI will not respond until the system is brought up again. After the system is up, the Web UI will refresh to the Device Info page automatically. The CT-5611T is ready for operation and the LEDs display as described in the LED description tables.
51
5.2.4 Bridging
Select the bridging mode. To configure Bridging, do the following.
1. Select Quick Setup and click Next.
2. Enter the PVC Index and click Next.
3. Type in the VPI and VCI values provided by the ISP and click Next.
4. Select the Bridging radio button and click Next. The following screen appears.
To use the bridge service, tick the checkbox, Enable Bridge Service, and enter the service name.
5. Click the Next button to continue. Enter the IP address for the LAN interface.
The default IP address is 192.168.1.1. The LAN IP interface in bridge operating mode is needed for local users to manage the ADSL router. Notice that there is no IP address for the WAN interface in bridge mode, and the remote technical support cannot access the ADSL router.
52
6. Click the Next button
The following screen will be displayed.
The WAN Setup-Summary screen presents the entire configuration summary. Click
Save/Reboot if the settings are correct. Click Back if you wish to modify the settings.
53
Chapter 6 Advanced Setup
This chapter explains: WAN, LAN, Routing, DSL and Port Mapping…...
Note: Shown below for your reference are the available menu options for each different configuration.
This screenshot is for PPPoE and PPPoA encapsulations.
This screenshot is for Mer and IPoA encapsulations.
54
This screenshot is for Bridge encapsulation.
6.1 WAN
VlanID • This function means one can add an 802.1Q VLAN tag on
PPPoE/MER or Bridge mode.
It means the packets are sent to WAN and a specific VlanID
(802.1Q tag) will be added in the Ethernet header. The VlanID shows which 802.1Q tag will be added.
For further information on WAN, please reference section: 4.1, Page 26.
55
6.2 LAN
Configure the DSL Router IP Address and Subnet Mask for LAN interface. Save button only saves the LAN configuration data. Save/Reboot button saves the LAN configuration data and reboots the router to make the new configuration effective.
IP Address: Enter the IP address for the LAN port.
Subnet Mask: Enter the subnet mask for the LAN port.
Enable IGMP Snooping: Enable /Disable the function that is IGMP Snooping.
Standard Mode: In standard mode, as in all prior releases, multicast traffic will flood to all bridge ports when there is no client subscribes to any multicast group – even when IGMP snooping is enabled.
Blocking Mode: In blocking mode, the multicast data traffic will be blocked and not flood to all bridge ports when there is no client subscription to any multicast group.
Ethernet Media Type: Select between Auto, 10_Half, 10_Full, 100_Half and 100_Full options.
56
To configure a secondary IP address for the LAN port, click the box as shown below.
IP Address: Enter the secondary IP address for the LAN port.
Subnet Mask: Enter the secondary subnet mask for the LAN port.
57
6.3 NAT
To display the NAT function, you need to enable the NAT feature in the WAN Setup.
Virtual Server allows you to direct incoming traffic from WAN side (identified by
Protocol and External port) to the Internal server with private IP address on the LAN side. The Internal port is required only if the external port needs to be converted to a different port number used by the server on the LAN side. A maximum 32 entries can be configured.
To add a Virtual Server, simply click the Add button. The following will be displayed.
58
Select a Service
Or
Custom Server
Server IP Address
User should select the service from the list.
Or
User can enter the name of their choice.
Enter the IP address for the server.
External Port Start Enter the starting external port number (when you select
Custom Server). When a service is selected the port ranges are automatically configured.
External Port End Enter the ending external port number (when you select
Custom Server). When a service is selected the port ranges are automatically configured.
Protocol User can select from: TCP, TCP/UDP or UDP.
Internal Port Start Enter the internal port starting number (when you select
Custom Server). When a service is selected the port ranges are automatically configured
Internal Port End Enter the internal port ending number (when you select
Custom Server). When a service is selected the port ranges are automatically configured.
59
Some applications require that specific ports in the Router's firewall be opened for access by the remote parties. Port Trigger dynamically opens up the
'Open Ports' in the firewall when an application on the LAN initiates a TCP/UDP connection to a remote party using the 'Triggering Ports'. The Router allows the remote party from the WAN side to establish new connections back to the application on the LAN side using the 'Open Ports'. A maximum 32 entries can be configured.
To add a Trigger Port, simply click the Add button. The following will be displayed.
60
Select an
Application
Or
Custom Application
Trigger Port Start
Trigger Port End
Trigger Protocol
Open Port Start
Open Port End
User should select the application from the list.
Or
User can enter the name of their choice.
Enter the starting trigger port number (when you select custom application). When an application is selected the port ranges are automatically configured.
Enter the ending trigger port number (when you select custom application). When an application is selected the port ranges are automatically configured.
User can select from: TCP, TCP/UDP or UDP.
Enter the starting open port number (when you select custom application). When an application is selected the port ranges are automatically configured.
Enter the ending open port number (when you select custom application). When an application is selected the port ranges are automatically configured.
User can select from: TCP, TCP/UDP or UDP. Open Protocol
61
The DSL router will forward IP packets from the WAN that do not belong to any of the applications configured in the Virtual Servers table to the DMZ host computer.
Enter the computer's IP address and click "Apply" to activate the DMZ host.
Clear the IP address field and click "Apply" to deactivate the DMZ host.
62
6.3.4 ALG
SIP ALG is Application layer gateway. If the user has an IP phone(SIP) or VoIP gateway(SIP) behind the ADSL router, the SIP ALG can help VoIP packet passthrough the router (NAT enabled).
Note: SIP (Session Initiation Protocol, RFC3261) is the protocol of choice for most VoIP
(Voice over IP) phones to initiate communication. This ALG is only valid for SIP protocol running UDP port 5060.
63
6.4 Security
To display the Security function, you need to enable the firewall feature in the WAN
Setup.
IP filtering allows you to create a filter rule to identify outgoing/incoming IP traffic by specifying a new filter name and at least one condition below. All of the specified conditions in this filter rule must be satisfied for the rule to take effect. Click
'Save/Apply' to save and activate the filter.
Outgoing
Note: The default setting for Outgoing is Accepted.
To add a filtering rule, simply click the Add button. The following screen will be displayed.
64
Filter Name
Protocol
Source IP address
Source Subnet Mask
Source Port (port or port:port)
Destination IP address
Destination Subnet Mask
Type a name for the filter rule.
User can select from: TCP, TCP/UDP, UDP or ICMP.
Enter source IP address.
Enter source subnet mask.
Enter source port number.
Enter destination IP address.
Enter destination subnet mask.
Destination port (port or port:port) Enter destination port number.
Incoming
Note: The default setting for Incoming is Blocked.
65
To add a filtering rule, simply click the Add button. The following screen will be displayed.
To configure the parameters, please reference Outgoing table above.
66
Parental control: allows parents, schools, and libraries to set access times for
Internet use.
To add a parental control, simply click the Add button. The following screen will be displayed.
Username:
MAC:
To set access Internet user name
To set what MAC to access Internet
Mon, Tue, Wed, Thu, Fri, Sat, Sun: To set what day can be access Internet
Start, Stop: To set time range for Internet Blocking
67
6.5 Quality of Service
To display the Security function, you need to enable the QoS feature in the WAN
Setup.
Choose Add to configure network traffic classes. The following screen will be displayed:
68
Traffic Class Name
Assign ATM Transmit Priority
Mark IP Precedence
Mark IP Type Of Service
Mark 802.1p if 802.1q is enabled on WAN
Physical LAN Port
Protocol
Source IP Address
Source Subnet Mask
Enter name for traffic class
Select Low, Medium or High.
Select between 1-7. The lower the digit shows the higher the priority
Select either: Normal Service, Minimize Cost,
Maximize Reliability, Maximize Throughput,
Minimize Delay
Select between 1-7. The lower the digit shows the higher the priority
User can select from: ENET, ENET(1-4), USB or Wireless.
User can select from: TCP, TCP/UDP, UDP or
ICMP.
Enter the source IP address.
Enter the subnet mask for the source IP address.
Enter source port number. UDP/TCP Source Port (port or port:port)
Destination IP address
Destination Subnet Mask
UDP/TCP Destination port (port or port:port)
802.1p Priority
Enter destination IP address.
Enter destination subnet mask.
Enter destination port number.
Select between 0-7. The lower the digit shows the higher the priority
69
6.6 Routing
The Routing dialog box allows you to configure Default gateway and Static Route.
If ‘Enable Automatic Assigned Default Gateway’ checkbox is selected, this router will accept the first received default gateway assignment from one of the
PPPoA, PPPoE or MER/DHCP enabled PVC(s). If the checkbox is not selected, enter the static default gateway AND/OR a WAN interface. Click 'Save/Apply' button to save it.
NOTE: If changing the Automatic Assigned Default Gateway from unselected to selected, You must reboot the router to get the automatic assigned default gateway.
70
Choose Static Route to display the Static Route screen. The Static Route screen lists the configured static routes, and allows configuring static routes. Choose Add or
Remove to configure the static routes.
To add static route, click the Add button to display the following screen. Enter the destination network address, subnet mask, gateway AND/OR available WAN interface then click Save/Apply to add the entry to the routing table.
71
6.7 DNS
If 'Enable Automatic Assigned DNS' checkbox is selected, this router will accept the first received DNS assignment from one of the PPPoA, PPPoE or MER/DHCP enabled
PVC(s) during the connection establishment. If the checkbox is not selected, enter the primary and optional secondary DNS server IP addresses. Click 'Save' button to save the new configuration. You must reboot the router to make the new configuration effective.
The Dynamic DNS service allows you to map a dynamic IP address to a static hostname in any of the many domains, allowing your DSL router to be more easily accessed from various locations on the Internet.
72
To add a dynamic DNS service, simply click the Add button. The following screen will be displayed:
D-DNS provider
Hostname
Interface
Username
Password
Select a dynamic DNS provider from the list
Enter the name for the dynamic DNS server.
Select the interface from the list
Enter the username for the dynamic DNS server.
Enter the password for the dynamic DNS server.
73
6.8 DSL
To access the DSL settings, First click On Advanced Setup and then click on DSL.
The DSL Settings dialog box allows you to select an appropriate modulation mode.
Option Description
G.dmt Enabled Sets G.Dmt if you want the system to use G.Dmt mode.
G.Lite Enabled
T1.413
Sets G.Lite if you want the system to use G.Lite mode.
Sets the T1.413 if you want the system to use only T1.413 mode.
ADSL2 Enabled The device can support the functions of the ADSL2.
AnnexL Enabled The device can support/enhance the long loop test.
ADSL2+ Enabled The device can support the functions of the ADSL2+.
AnnexM Covers a higher “upstream” data rate version, by making use of some of the downstream channels.
Inner Pair
Outer Pair
Bitswap Enable
SRA Enable
Reserved only
Reserved only
Allows bitswaping function
Allows seamless rate adaptation
74
6.9 Port Mapping
Port Mapping supports multiple ports to PVC and bridging groups. Each group will perform as an independent network. To support this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the Add button. The Remove button will remove the grouping and add the ungrouped interfaces to the Default group.
To add a port mapping group, simply click the Add button.
75
To create a group from the list, first enter the group name and then select from the available interfaces on the list.
Automatically Add Clients With the Following DHCP Vendor IDs:
Add support to automatically map LAN interfaces and USB to PVC's using DHCP vendor ID (option 60). The local DHCP server will decline and send the requests to a remote DHCP server by mapping the appropriate LAN interface. This will be turned on when Port Mapping is enabled.
There are 4 PVCs (0/33, 0/36, 0/37, 0/38). 0/33 is for PPPoE and the others are for IP setup-box (video).
The Lan interfaces are ETH and USB.
Port mapping configuration are:
76
1. Default : ENET and USB.
2. Video: nas_0_36, nas_0_37 and nas_0_38. The DHCP vendor ID is "Video".
The CPE's dhcp server is running on "Default". And ISP's dhcp server is running on PVC
0/36. It is for setup-box use only.
In the LAN side, PC can get IP address from CPE's dhcp server and access Internet via
PPPoE (0/33).
If the setup-box was connected with interface "ENET" and send a dhcp request with vendor id "Video", CPE's dhcp server will forward this request to ISP's dhcp server.
And CPE will change the port mapping configuration automatically. The portmapping configuration will become:
1. Default : ENET and USB.
2. Video: nas_0_36, nas_0_37, nas_0_38 and ENET.
77
6.10 Certificate
A certificate is a public key, attached with its owner’s information (company name, server name, personal real name, contact e-mail, postal address, etc) and digital signatures. There will be one or more digital signatures attached on the certificate, indicating that these signers have verified that the owner information of this certificate is correct.
6.10.1 Local
Click Create Certificate Request to generate a certificate signing request. The certificate signing request can be submitted to the vendor/ISP/ITSP to apply for a certificate. Some information must be included in the certificate signing request.
Actually, your vendor/ISP/ITSP will ask you to provide the information they require and to provide the information in the format they regulate. The explanation for each column in the following table is only for reference.
78
Click Apply to generate a private key and a certificate signing request.
Certificate Name
Common Name
A user-defined name for the certificate.
Usually, it is the fully qualified domain name for the machine.
Organization Name The exact legal name of your organization. Do not abbreviate.
State/Province Name The state or province where your organization is located. It cannot be abbreviated.
Country/Region Name The two-letter ISO abbreviation for your country.
This page is used to paste the certificate content and the private key provided by your vendor/ISP/ITSP.
79
6.10.2 Trusted CA
CA is the abbreviation for Certificate Authority. CA is a part of the X.509 system. It is itself a certificate, attached with the owner information of this certificate authority. But its purpose is not to do encryption/decryption. Its purpose is to sign and issue certificates; in order to prove the owner information of that certificate is correct.
Click Import Certificate to paste the certificate content of your trusted CA. Generally speaking, the certificate content will be provided by your vendor/ISP/ITSP and is used to authenticate the Auto-Configuration Server (ACS) that the CPE will connect to.
80
Chapter 7 Diagnostics
The Diagnostics menu provides feedback on the connection status of the CT-5611T and the ADSL link. The individual tests are listed below. If a test displays a fail status, click Rerun Diagnostic Tests at the bottom of this page to make sure the fail status is consistent. If the test continues to fail, click Help and follow the troubleshooting procedures.
Test Description
Ethernet Connection Pass: indicates that the Ethernet interface from your computer is connected to the LAN port of your DSL Router.
A flashing or solid green LAN LED on the router also signifies that an Ethernet connection is present and that this test is successful.
Fail: Indicates that the DSL Router does not detect the
Ethernet interface on your computer.
USB connection
ADSL
Synchronization
Pass: Indicates that the USB interface from your computer is connected to the LAN port of your DSL router.
Down: Indicates that the DSL Router does not detect the
USB interface on your computer.
Pass: Indicates that the DSL modem has detected a DSL signal from the telephone company. A solid WAN LED on the router also indicates the detection of a DSL signal from the telephone company.
Fail: indicates that the DSL modem does not detect a signal from the telephone company’s DSL network. The
WAN LED will continue to flash green.
ISP Connection Pass: Indicates we can access the WAN service like the
Gateway and DNS.
Fail: Indicates we cannot access the WAN side.
81
Chapter 8 Management
The Management section of the CT-5611T supports the following maintenance functions and processes:
• Settings
• System log
• TR-069 Client
• Internet Time
• Access Control
• Update software
• Save/Reboot
8.1 Settings
The Settings option allows you to back up your settings to a file, retrieve the setting file, and restore the settings.
82
8.1.1 Configuration Backup
The Backup option under Management>Settings, save your router configurations to a file on your PC. Click BACKUP Settings in the main window. You will be prompted to define the location of the backup file to save. After choosing the file location, click
Backup Settings. Te file will then be saved to the assigned location.
The Update option under Management>Settings update your router settings using your saved files.
83
Clicking the Restore Default Configuration option in the Restore Settings screen can restore the original factory installed settings.
NOTE: This entry has the same effect as the hardware reset-to-default button.
The CT-5611T board hardware and the boot loader support the reset to default button. If the reset button is continuously pushed for more than 5 seconds, the boot loader will erase the entire configuration data saved on the flash memory.
NOTE: Restoring system settings, requires a system reboot. This necessitates that the current Web UI session be closed and restarted. Before restarting, the connected PC must be configured with a static IP address in the 192.168.1.x subnet in order to configure the CT-5611T.
Default settings
The CT-5611T default settings are z z z z z
LAN port IP= 192.168.1.1, subnet mask = 255.255.255.0
Local user name: admin
Password: tot
Remote user name: support
Remote user password: support
After the Restore Default Configuration button is selected, the following screen appears. Close the DSL Router Configuration window and wait for 2 minutes before reopening your web browser. If necessary, reconfigure your PC's IP address to match your new configuration.
84
8.2 System Log
The System Log option under Management>Settings allows you to view the system events log, or to configure the System Log options. The default setting of system log is disabled. Follow the steps below to enable and view the system log.
1. Click Configure System Log to display the following screen.
2. Select from the desired Log options described in the following table, and then click
Save/Apply.
85
Option Description
Log Indicates whether the system is currently recording events. The user can enable or disable event logging. By default, it is disabled.
To enable it, tick Enable and then Apply button.
Log level Allows you to configure the event level and filter out unwanted events below this level. The events ranging from the highest critical level “Emergency” down to this configured level will be recorded to the log buffer on the CT-5611T SDRAM. When the log buffer is full, the newer event will wrap up to the top of the log buffer and overwrite the old event. By default, the log level is “Debugging,” which is the lowest critical level. The following log levels are z
Emergency = system is unusable z z
Alert = action must be taken immediately
Critical = critical conditions z z z z
Error = Error conditions
Warning = normal but significant condition
Notice= normal but insignificant condition
Informational= provides information for reference
Display
Level
Mode z
Debugging = debug-level messages
Emergency is the most serious event level, whereas Debugging is the least important. For instance, if the log level is set to Debugging, all the events from the lowest Debugging level to the most critical level Emergency level will be recorded. If the log level is set to
Error, only Error and the level above will be logged.
Allows the user to select the logged events and displays on the
View System Log page for events of this level and above to the highest Emergency level.
Allows you to specify whether events should be stored in the local memory, or be sent to a remote syslog server, or both simultaneously.
If remote mode is selected, view system log will not be able to display events saved in the remote syslog server.
When either Remote mode or Both mode is configured, the WEB UI will prompt the user to enter the Server IP address and Server UDP port.
3. Click View System Log. The results are displayed as follows.
86
8.3 TR-069 Client
WAN Management Protocol (TR-069) allows a Auto-Configuration Server (ACS) to perform auto-configuration, provision, collection, and diagnostics to this device.
Option Description
Inform Interval
ACS URL
The duration in seconds of the interval for which the CPE
MUST attempt to connect with the ACS and call the Inform method.
URL for the CPE to connect to the ACS using the CPE WAN
Management Protocol. This parameter MUST be in the form of a valid HTTP or HTTPS URL. An HTTPS URL indicates that the ACS supports SSL. The “host” portion of this URL is used by the CPE for validating the certificate from the ACS when using certificate-based authentication.
ACS User Name Username used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management
Protocol. This username is used only for HTTP-based authentication of the CPE.
ACS Password Password used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management
Protocol. This password is used only for HTTP-based authentication of the CPE.
Connection Request
User Name
Connection Request
Password
Username used to authenticate an ACS making a Connection
Request to the CPE.
Password used to authenticate an ACS making a Connection
Request to the CPE.
87
Get RPC Methods This method may be used by a CPE or ACS to discover the set of methods supported by the ACS or CPE it is in communication with. This list may include both standard TR-
069 methods (those defined in this specification or a subsequent version) and vendor-specific methods. The receiver of the response MUST ignore any unrecognized methods. Click this button to force the CPE to immediately establish a connection to the ACS.
88
8.4 Internet Time
The Internet Time option under Management menu bar configures the Modem’s time.
To automatically synchronize with Internet timeservers, tick the corresponding box displayed on the screen. Then click Save/Apply.
8.5 Access Control
The Access Control option under Management menu bar configures the accessrelated parameters, including three parts: Services, IP Address, and Passwords.
89
Note: LAN and WAN side are present on the screen if the WAN interface is UP. Only the LAN side will be displayed if the ADSL or WAN interface is down.
8.5.1 Services
The Services option limits or opens the access services over the LAN or WAN. These services are provided FTP, HTTP, ICMP, SNMP, SSH (Security Socket Share), TELNET, and TFTP. Enable the service by checking the item in the corresponding checkbox, and then click Save/Apply.
90
The IP Addresses option limits the access by IP address. If the Access Control Mode is enabled, only the allowed IP addresses can access the router. Before you enable it, configure the IP addresses by clicking the Add button. Enter the IP address and click Apply to allow the PC with this IP address managing the DSL Router.
91
8.5.3 Passwords
The Passwords option configures the access passwords for the router. Access to your DSL router is controlled through three user accounts: admin, support, and user. z z
“admin” has unrestricted access to change and view configuration of your DSL
Router.
"support" is used to allow an ISP technician to access your DSL Router for maintenance and to run diagnostics. z
"user" can access the Router, view configuration settings and statistics, as well as, update the router's software.
Use the fields below to enter up to 16 characters and click Apply to change or create passwords.
92
8.6 Update Software
The Update Software screen allows you to obtain an updated software image file from your ISP. Manual software upgrades from a locally stored file can be performed using the following screen.
Step 1: Obtain an updated software image file from your ISP.
Step 2: Enter the path to the image file location in the box below or click the
Browse button to locate the image file.
Step 3: Click the "Update Software" button once to upload the new image file.
NOTE: The update process takes about 2 minutes to complete, and your DSL
Router will reboot.
93
8.7 Save and Reboot
The Save/Reboot option saves the configurations and reboots the router. Close the
DSL Router Configuration window and wait for 2 minutes before reopening your web browser. If necessary, reconfigure your PC's IP address to match your new configuration.
94
Appendix A: Pin Assignments
Line port (RJ11)
Pin Definition Pin Definition
2 - 5 -
3 ADSL_RING 6 -
Pin Assignments of the RJ11 Port
LAN Port (RJ45)
Pin
2
Definition
Transmit data-
Pin
6
Definition
NC
Receive data-
NC
4 NC 8 NC
Pin assignments of the LAN Port
95
Appendix B: Specifications
Rear Panel
RJ-11 X1 for ADSL, RJ-45 X 1 for LAN, USB X 1 for LAN, Reset Button X 1, Power switch X 1
ADSL
Standard ITU-T G.992.5, ITU-T G.992.3, ITU-T G.992.1, ANSI T1.413 Issue 2
G.992.5 (ADSL2+) Downstream : 24 Mbps Upstream : 1.3 Mbps
G.992.3 (ADSL2) Downstream : 12 Mbps
G.DMT
Upstream : 1.3 Mbps
Downstream: 8 Mbps Upstream: 832 Kbps
Ethernet
Standard
10/100 BaseT
MDI/MDIX
IEEE 802.3, IEEE 802.3u
Auto-sense
Yes
ATM Attributes
RFC 2364 (PPPoA), RFC 2684 (RFC 1483) Bridge/Route; RFC 2516 (PPPoE);
RFC 1577 (IPoA)
Support PVCs 8
AAL type
ATM service class
ATM UNI support
OAM F4/F5
AAL5
UBR/CBR/VBR
UNI3.1/4.0
Yes
Management
TR-069, SNMP, Telnet, Web-based management, Configuration backup and
restoration
Software upgrade via HTTP, TFTP server, or FTP server
Bridge Functions
Transparent bridging and learning IEEE 802.1d
Spanning Tree Algorithm Yes
IGMP Proxy Yes
Routing Functions
Static route, NAT/PAT, DHCP Server/DHCP Relay, DNS Proxy, ARP
Security Functions
Authentication protocols PAP, CHAP,
TCP/IP/Port filtering rules, Port triggering/Forwarding, Packet and MAC address filtering, access control,
96
Application Passthrough
PPTP, L2TP, IPSec, VoIP, Yahoo messenger, ICQ, RealPlayer, NetMeeting,
MSN, X-box, etc.
Power Supply
External power adapter 110 Vac or 220 Vac
Environment Condition
Operating temperature 0 ~ 50 degrees Celsius
Relative humidity 5 ~ 95% (non-condensing)
Dimensions
114 mm (W) x 32 mm (H) x 92 mm (D)
Certifications
FCC Part 15 class B, FCC Part 68, CE
Note: Specifications are subject to change without notice
97
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project