P735
Quick Start Guide
Package contents
Check your P735 package for the following items:
P ASUS P735 device
P Battery
P AC Adapter
P Mini-USB cable
P Headset
P Stylus
P Protection case
P Getting Started CD
P User Manual
P Quick Start Guide
P Warranty Card
NOTE:
If any of the above items is damaged or missing, contact your retailer.
CAUTION:
• To reduce risk of fire, use only correct battery type. Refer to “Installing the SIM card and battery” section for details.
• Do not attempt to disassemble the battery pack.
• Dispose of used batteries properly. Inquire from local authorities for proper disposal of battery.
Getting to know your P735
Layout
3
2
1
20
Top features
7
24
22
19
8
21
9
25
4
23
5
10
Right side features
Rear features
12
16
6
11
13
Left side features
18
15
26
27
28
17
14
Front features
Bottom features
Device components description
No.
Item
Description
1
MiniSD slot
Allows you to insert a MiniSD storage card.
2
Power button
Press to turn the power ON or to set suspend mode or to wake
device from sleep mode.
Press and hold to turn the power OFF.
3
Stylus
Use the stylus to write, draw, or select items on the touch screen.
4
Camera/Shutter button
Press to launch the camera. In camera mode, half-press to autofocus then full-press to take a picture. In video mode,
full-press to start recording video and press again to stop.
5
Volume controller
Press the arrow buttons to adjust the volume.
6
Reset button
Using the stylus, press reset button to soft-reset your device.
7
Notification LED
This multi-color LED notifies the following:
• Green - Phone fully charged.
• Flashing green - Network detected.
• Red - Phone is charging.
• Flashing red - Event notification.
• Flashing blue - Bluetooth® or WLAN(IEEE 802.11b/g) ON.
8
Earpiece receiver
Allows you to listen to incoming/outgoing calls.
9
Sub camera lens
This sub camera is for the video conference.
10
LCD touch screen
This 2.8-inch, 65536-color, 240 x 320-resolution, touchscreen TFT
LCD allows you to write, draw, or make selections using the stylus.
11
Call key
Press to receive an incoming call or make a call.
12
Left Soft key
Performs the command indicated above the button.
13
Video call button
Press to make video calls.
Device components description
No.
Item
Description
14
Navigation buttons
Use to move through menus. Press the center to run an application or
in camera mode, press to take a picture.
15
Action button
Press to carry out the task of selected item.
16
Right Soft key
Performs the task indicated above the button.
17
Mode/Task switcher button
Allows you to switch applications and tasks.
Press and hold this button to turn on/off the flashlight.
18
End key
Press to end a call or GPRS Connection.
19
Camera flashlight
Allows you to capture images in a dim environment.
Press and hold the mode switcher button to turn this flashlight on/off.
It works on today screen only.
20
Self-Portrait Mirror
Position your device until this mirror reflects the image you want to capture.
21
Camera lens
This 2-megapixel camera comes with Auto-Focus (AF) lens and flash
light features.
22
Speaker
Allows you to listen audio media and phone calls.
23
Battery compartment
Contains the battery that supplies power to the device.
24
Voice Commander/record
button
Press to launch the voice commander.
Press and hold to launch the record application to record voice.
25
Hold button
Slide to enable or disable all keys including the LCD touch screen.
26
Earphone port
Plug headset accessory to this port.
27
Mini-USB connector
Use this connector to synchronize your data or to charge the battery.
28
Mic
Used to make or receive phone calls, record sounds, record voice, or
say voice commands.
NOTE: The Voice Command utility is supported in selected languages only.
Getting your device ready
Before you can start using your device, you need to install a Subscriber Identity Mode (SIM)
card and a charged battery. A SIM card contains your phone number, subscriber details,
phone book, and additional phone memory.
Installing the SIM card and battery
1. Remove the battery compartment cover then remove battery.
3. Insert the SIM card with its gold contacts facing down and the notched corner
oriented to the upper left corner of the slot.
4. Replace the battery into the compartment with its copper contacts aligned to the
copper conductor on the device.
5. Replace battery compartment cover.
CAUTION:
Use only an ASUS qualified battery for this device.
Charging the battery
The bundled battery pack is shipped partially charged. Make sure to charge the battery at least
four hours before using it for the first time.
To charge the battery:
1. Connect the AC adapter plug to the
mini-USB connector at the bottom of the device.
2. Connect the AC power plug to a grounded wall
socket or power strip. The LED indicator turns
red while the phone is charging.
Powering your device
After charging the battery, you are now ready to use your device.
To power on your device:
1. Press and hold the power button to turn ON the device.
2. Follow the succeeding screen instructions to setup your Windows Mobile-based device.
The Today screen
The Today screen displays information useful to you.
Tap to open the Start menu
Tap to setup date, time, and alarm.
Status bar
Indicates the battery status
Tap to adjust volume
Displays the signal status
Displays the current network
provider and connection status
Tap to set user information
Tap to open messages
Tap to setup profile
Tap to read or make appointments
Tap to launch live search
Tap to setup tasks
Tap to view connectivity status
Displays the Bluetooth®
connection status
Tap to lock, unlock, or change
My Secrets settings
(Appears only when My Secrets is enabled.)
Tap to change Bluetooth­
settings
Tap to display system CPU,
USB setting, LCD brightness,
battery, memory, and MiniSD
status
Tap to change WLAN
(IEEE 802.11b) settings
(Appears only when WiFi is turned on and
connected to the Internet.)
Tap to display call history
Tap to change screen
orientation
Tap to launch Contacts list
ASUS Status icon
The ASUS status icon allows you to easily check and see the current status of the following
device components: CPU, USB, LCD Brightness, battery power, Memory, MiniSD card, and
device storage.
To check the status of these components, tap the ASUS Status icon
on the Today screen.
CPU: Allows you to set the CPU mode. Set to
Automatic Mode to automatically change the CPU
speed according to the CPU loading.
USB: Allows you to set the USB connection mode.
Brightness: Tap to adjust the LCD brightness on
battery power or external power.
Power: Displays the remaining battery power and
allows you to set advanced power saving features.
Memory: Displays the total, currently used, and
remaining memory available.
Storage memory: Displays the total, used, and
remaining storage memory.
Storage: Tap to display the contents of the storage
card installed. ( Appears only when a MiniSD card is inserted in the
device)
Settings: Allows you to select the items to display
in this ASUS Status pop-up menu.
Entering information
Using the Input panel
The Input Panel allows you to select various
input methods available on your device
including: Block Recognizer, Keyboard,
Letter Recognizer, and Transcriber.
Tap the Input panel icon to display shortcut
menu and select input method.
Input panel icon
Input panel methods
Block Recognizer
Keyboard
Letter Recognizer
Transcriber
Messages
Sending a message
Your device allows you to send and receive email, SMS, MMS, and MSN messages when
connected to a network. The following describes how to compose and send a message.
Composing and sending a message
1. Tap Start then Messaging.
2. Select account:
• Text Messages
• Outlook E-mail
• MMS
3. Tap Menu > New.
4. Key in the email address or phone number of one
or more recipients, separating them with a
semi-colon. To launch Contacts list, tap Menu >
Add Recipient.
5. Key in your message.
10
Using Windows Live Messenger
1. Tap Start > Programs> Messenger icon to
launch Windows Live Messenger.
2. Tap Sign in to Windows Live Messenger. From
the screen appears, tap Accept.
2. Key in the e-mail address and password, then
tap Sign In.
Tap to check Save password box to save
password.
3. Follow succeeding screen instructions to setup
Windows Live Messenger.
NOTE:
•To use Windows Live Messenger, you need a Microsoft .NET Passport. Go to www.passport.com to obtain a
Passport.
• GPRS will automatically reconnect when your Windows Live Messenger status is online.
11
Synchronizing with Exchange Server
Before you can synchronize your device with an Exchange Server, install the Microsoft®
ActiveSync™ to your computer using the bundled P735 Getting Started CD. Activesync™ is the
software that synchronizes your P735 with a Windows® powered computer. Your P735 comes
with a preinstalled ActiveSync™. To synchronize your device with Exchange Server:
1. From the ActiveSync menu, tap
Menu > Add Server Source.
4. Tap the check boxes to select the data
items that you want to synchronize
with Exchange Server. To change the
available synchronization settings,
select a data item then tap Settings.
Tap Finish when done.
5. Start the sync process.
2. In the Server Address field, input
the name of the server running
Exchange Server then tap Next.
3. Input your name, password, and
domain then tap Next.
12
NOTE: Refer to the User Manual for details on changing
the synchronization schedule.
Personalizing your device
You can customize the look and feel of your device according to your desired settings.
Entering owner information
To update the owner information:
1. Tap Start > Settings > Personal tab then tap the
Owner Information icon or tap the
icon on the Today
screen.
2. Key in information.
3. Tap
when done.
Tap to set owner information
Customizing the Start menu
To customize the Start menu:
1. Tap Start > Settings > Personal tab.
2. Tap the Menus icon.
3. Check the items that you want to appear on the menu.
4. Tap
when done.
13
Setting phone sounds
(Ring Type, ring tone, and keypad sound )
To setup your phone sounds:
1. Tap Start > Settings > Personal tab.
2. Tap the Phone icon.
3
From the phone screen, tap Ring Type box to
select desired ring type.
Tap Ring tone box to select desired ring type.
Tap Keypad box to select the keypad sound.
4. Tap
when done.
Setting theme
To setup theme:
1. Tap Start > Settings > Personal tab > Today.
2. Select a theme from the list.
Tap the Use this picture as the background
check box if you want to use this picture as device
screen background.
3. Tap
14
when finished.
Setting Date and Time
You can launch the Date and Time screen directly from the Today screen.
To edit date and time:
1. Tap the clock
icon on the Today screen.
2. Select the correct time zone and
change the date or time.
NOTE:
During synchronization, the date and time on your
device is updated with the date and time on your
computer.
Setting Profile
To change your device profile:
1. Tap Start > Settings > Personal tab then
tap Profile icon.
2. Adjust current Sound and Notifications
settings.
15
Wireless features
Using WLAN (IEEE 802.11b)
To activate WLAN in your device:
1. Tap Start > Settings > Connections tab then tap the Wi-Fi Manager icon.
2. From the Wi-Fi Manager screen, tap Menu then Turn Wi-Fi On.
You can also turn Wi-Fi ON or OFF from the Today screen.
IMPORTANT:
• When WLAN is used simultaneously with the GPRS, the latter will get signal priority. We recommend not to use
WLAN and GPRS at the same time.
•We recommend not to use WLAN and the Bluetooth function at the same time. It may cause disturbance in data transmission since both use the same wireless channel.
•The WLAN and USB connections cannot be used at the same time.
• When the battery power is less than 20% the device prompts a warning message whether to continue using WiFi or
not. Tap “Yes” to continue using or “No” to disconnect. We recommend that you plug the power adapter immediately to avoid losing data.
Using Bluetooth™
To activate (turn ON) Bluetooth in your device:
1. Tap Start > Settings > Connections tab then tap the Bluetooth icon.
2. From the Bluetooth screen, tap General tab.
3. Tap Turn on button. The Bluetooth status is displayed above the Turn on/Turn off
buttons.
16
You can also turn Bluetooth ON or OFF from the Today screen. To do this:
1. Find the Bluetooth icon
2. Tap
at the bottom right corner of the Today screen.
to display shortcut menu then tap Turn Bluetooth ON.
The Bluetooth icon changes to
if Bluetooth is turned Off.
NOTES:
The Bluetooth device setup instructions provided in this section may differ with other Bluetooth devices. If the
instructions in this guide differs from the documentation that came with your Bluetooth-enabled device, follow the latter.
Using a Bluetooth-enabled headset
Mono headset setup
1. Make sure that Bluetooth is enabled on your device.
2. Tap
on the Today screen then on the shortcut menu tap
Bluetooth Manager.
3. From the Bluetooth Manager, tap New.
4. From the Connection Wizard, tap Hands-free/Headset setup
then tap Next.
5. Make sure that your headset device is in pairing mode and
ready to receive incoming connection requests then tap Next.
6. Tap the name of your Bluetooth-enabled headset device.
7. In Passkey, input the alphanumeric passkey of your headset device then tap OK. You
can find this in the documentation that came with your headset device.
8. Tap Finish. You are now ready to use your headset device.
NOTES:
If the connection between the device and a Bluetooth headset fails, press the device icon then choose
“reconnect”, you do not have to pair the devices again
17
Stereo headset setup
P735 supports A2DP (Advanced Audio Distribution Profile), which is used by Bluetooth-enabled
stereo headsets. Make sure that your stereo headset also supports A2DP.
1. Tap
on the Today screen then on the shortcut menu tap Bluetooth Manager.
2. From the Bluetooth manager screen, tap New then select High
Quality Audio Setup.
3. Make sure that your stereo headset device is in pairing mode
and ready to receive incoming connection requests then tap
Next.
4. Tap the name of your stereo headset device then tap Next.
• If you want to create a shortcut, tap the check box Create a shortcut for this connection then input a connection name.
• If you want to use a secure connections, tap the check box
to Use a secure, encrypted connection.
5. Tap Finish to initiate connection.
IMPORTANT:
To answer a phone call using your stereo headset, make sure that you have
mono and stereo connection at the same time.
NOTE:
To use voice commander while using a headset, press the answer button on the
headset then follow given instructions.
18
Using the Network Setting Tool
The Network Setting Tool allows you to conveniently select and connect to your 3G/GPRS
service provider.
To connect via Network Setting:
1. Tap Start > Settings > Connections
tab then tap the Network Setting
icon.
or
on the
You can also tap
status bar then tap Settings from the
pop-up callout.
2. From the Network Setting screen,
select your service providers from the
list.
NOTE:
The 3G/GPRS and USB connections can not be
used at the same time.
19
Connecting 3G/GPRS
To connect 3G/GPRS:
1. Launch any application that connects
to the Internet (e.g. Internet Explorer).
The device will automatically connect
your default 3G/GPRS connection. A
pop-up callout appears to display the
connection status.
2. When connected, you can start
browsing the Internet. If you’re using
Internet Explorer, the default site will
be displayed.
Disconnecting 3G/GPRS
To disconnect 3G/GPRS:
1. Tap
or
from the status bar.
2. From the pop-up callout, tap
Disconnect.
3. Tap
to exit.
NOTE:
• If your ActiveSync is set to sync with Exchange
Server automatically, synchronization will occur
after you connect again.
• 3G/GPRS will automatically reconnect everytime
you launch an application that requires 3G/GPRS
connection (e.g. Internet Explorer or Pocket MSN).
20
Pop-up callout
Notices
Replaceable batteries
If an equipment is provided with a replaceable battery and if replacement by an
incorrect type could result in an explosion (e.g. with some lithium batteries), the
following applies:
– If the battery is placed in an OPERATOR ACCESS AREA, there shall be a
marking close to the battery or a statement in both the operating and the
servicing instructions;
– If the battery is placed elsewhere in the equipment, there shall be a marking
close to the battery or a statement in the servicing instructions.
The marking or statement shall include the following or similar text:
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO
THE INSTRUCTIONS
21
Operator access with a tool
If a TOOL is necessary to gain access to an OPERATOR ACCESS AREA, either
all other compartments within that area containing a hazard shall be inaccessible
to the OPERATOR by the use of the same TOOL, or such compartments shall be
marked to discourage OPERATOR access.
An acceptable marking for an electric shock hazard is (ISO 3864, No. 5036).
Equipment for restricted access locations
For equipment intended only for installation in a RESTRICTED ACCESS
LOCATION, the installation instructions shall contain a statement to this effect.
22
RF Exposure Information (SAR)
THIS MODEL MEETS INTERNATIONAL GUIDELINES FOR EXPOSURE TO RADIO
WAVES
Your mobile device is a radio transmitter and receiver. It is designed not to exceed the limits
for exposure to radio waves recommended by international guidelines. These guidelines were
developed by the independent scientific organization ICNIRP and include safety margins
designed to assure the protection of all persons, regardless of age and health.
The guidelines use a unit of measurement known as the Specific Absorption Rate, or SAR.
The ICNIRP SAR limit for mobiles devices used by the general public is 2 W/kg and the
highest SAR value for this device when tested at the ear was 0.712 W/kg*. As mobile devices
offer a range of functions, they can be used in other positions, such as on the body as
described in this user guide. In this case, the highest tested SAR value is 0.848 W/kg*.
As SAR is measured utilizing the devices highest transmitting power, the actual SAR of
this device while operating is typically below that indicated above. This is due to automatic
changes to the power level of the device to ensure it only uses the minimum level required to
reach the network.
While there may be differences between the SAR levels of various phones and at various
positions, they all meet the governmental requirements for safe exposure. Please note
that improvements to this product model could cause differences in the SAR value for later
products; in all cases, products are designed to be within the guidelines.
The World Health Organization has stated that present scientific information does not indicate
the need for any special precautions for the use of mobile devices. They note that if you
want to reduce your exposure then you can do so by limiting the length of calls or using a
‘handsfree’ device to keep the mobile phone away from the head and body.
23
Additional Information can be found on the websites of the World Health Organization
(http://www.who.int/emf).
* The tests are carried out in accordance with international guidelines for testing. The limit incorporates a substantial margin for safety to give additional protection for the public and to account for any variations in measurements. Additional related information includes the ASUS testing protocol, assessment procedure, and measurement uncertainty range for this product.
24
WARNING
The user needs to switch off the device when exposed to areas with potentially
explosive atmospheres such as petrol stations, chemical storage depots and
blasting operations.
25
ASUS
Address: 15 Li-Te Road, Peitou, Taipei, Taiwan
Tel: 886-2-2894-3447; Fax: 886-2-2890-7698
Declaration
We declare that the IMEI codes for this product, P735, are unique to each unit
and only assigned to this model. The IMEI of each unit is factory set and cannot
be altered by the user and that it complies with the relevant IMEI integrity related
requirements expressed in the GSM standards.
Should you have any questions or comments regarding this matter, please have
my best attention.
Sincerely yours,
Contact Person: Jonathan Wu
Company: ASUSTeK COMPUTER INC.
Tel: 886-2-2894-3447 Ext: 7225
Fax: 886-2-2890-7698
E-mail: http://vip.asus.com/eservice/techserv.aspx
26
Contact information
ASUSTeK COMPUTER INC. (Taiwan)
Hotline: 0800-093-456 (Toll-Free call from Taiwan only)
Fax:
886-2-2895-9254
E-mail: http://vip.asus.com/eservice/techserv.aspx
WWW: http://tw.asus.com
ASUSTeK COMPUTER INC. (Asia-Pacific)
Hotline: 886-2-2894-3447
Fax:
886-2-2890-7698
E-mail: http://vip.asus.com/eservice/techserv.aspx
WWW: http://www.asus.com
ASUS COMPUTER GmbH (Germany/Austria)
Hotline: MB/Others: +49-2102-9599-0
Notebook:+49-2102-9599-10
Fax:
+49-2102-9599-11
E-mail: http://www.asus.de/support/support.htm
WWW: http://www.asus.de
ASUS COMPUTER (China)
Tel:
+86-10-82667575
E-Mail: http://vip.asus.com.cn/eservice/techserv.aspx.
27
28