Electrolux ERCE9025BK User manual

installation
and user manual
ERCE9025BK
canopy rangehood
2 contents electrolux canopy rangehood
Congratulations
Congratulations and thank you for choosing our canopy
rangehood. We are sure you will find your new rangehood
a pleasure to use. Before you use your rangehood, we
recommend that you read through the whole user manual,
which provides the description of the rangehood and its
function.
To avoid the risks that are always present when you use
an electrical appliance it is important that the canopy
rangehood is installed correctly and that you read the
safety instructions carefully to avoid misuse and hazards.
We recommend that you keep this instruction booklet for
future reference and pass it on to any future owners. After
unpacking the canopy rangehood please check it is not
damaged. If in doubt, do not use the appliance but contact
your local Electrolux Service Centre.
Contents
• Important safety instructions • Product description
• Dimensions
• Installation
• Using the rangehood
• Maintenance and cleaning
• Changing the halogen lamps
• Optional ducting accessories
• Warranty
3
4
5
6
9
9
9
10
11
environmental tip
Information on disposal for users
•Most of the packing materials are recyclable. Please
dispose of those materials through your local recycling
depot or by placing them in appropriate collection
containers.
•If you wish to discard this product, please contact your
local authorities and ask for the correct method of disposal.
electrolux canopy rangehood important safety instructions 3
Important safety instructions
This manual explains the proper use of your new Electrolux
canopy rangehood. Please read this manual carefully before
using the product. This manual should be kept in a safe
place for handy reference.
This canopy rangehood is a domestic appliance which has
been manufactured and tested to comply with Australian
and New Zealand Standard AS/NZS 60335.2.31.
caution
This symbol indicates the possibility of injury or
damage to property
Meanings of symbols used in this manual are shown below:
This symbol indicates never to do this
This symbol indicates always do this
caution
Read the following carefully to avoid an electric
shock or fire.
Young children should be supervised to ensure they do not
play with the canopy rangehood.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning the use of the
appliance by a person responsible for their safety.
Ensure the canopy rangehood is switched off before
carrying out maintenance, to avoid any possibility of electric
shock.
Electrical connection
Check that the mains voltage matches with the voltage on
the data plate inside the canopy rangehood. Check that the
installation complies with standards of local building, gas and
electrical authorities. Before connecting to the mains supply
ensure that the mains voltage corresponds to the voltage on
the rating plate inside the cooker hood.
If the supply cord is damaged, it must be replaced by
the manufacturer or its service agent of similarly qualified
person in order to avoid a hazard.
Safety warnings – For the installer
When installing the cooker hood, make sure you adhere to
the minimum and maximum distances from the cooker hood
base to the hob surface (as per table on following page).
Exhaust flue installation: The following rules must be
strictly followed to obtain optimal air extraction.
•Keep exhaust flue short and straight
•Do not reduce the size or restrict exhaust flue.
•Keep bends in the exhaust flue to a minimum.
•When using flexible flue always install duct with helix pulled
taut to minimise pressure loss.
•Failure to observe these basic instructions will drastically
reduce the performance and increase the noise levels of
the cooker hood.
Exhaust air must not be discharged into a wall cavity, unless
the cavity is designed for that purpose.
The exhaust from the cooker hood must not be discharged
into any heating flue, which may carry combustion products
from other sources
NOTE: Some installations may require the telescopic
exhaust cover to be cut to length. Cut with sharp tin snips
or a fine-tooth hack saw blade, taking care not to distort or
dent the exhaust cover.
Never carry out flambé cooking under the canopy rangehood.
This canopy rangehood is not recommended for barbecues.
This canopy rangehood cannot be installed for external use.
Grease filters must be removed every four weeks
(maximum) for cleaning to reduce the risk of fire.
The exhaust from the canopy rangehood must not
be discharged into any heating flue, which may carry
combustion products from other sources. (Fig. 1)
Exhaust air must not be discharged into a wall cavity,
unless the cavity is designed for the purpose.
There must be adequate ventilation of the room when the
canopy rangehood is used at the same time as appliances
burning gas or other fuels.
Always cover lit gas burners with pots or pans when
canopy rangehood is in use.
Always switch off gas burners before you remove pots or pans.
Do not leave lit gas burners exposed due to the risk of fire.
(Fig. 2)
Fig. 1
Fig. 2
4 product description electrolux canopy rangehood
Product description 1
2
3
4
5
6
7
8
Component list
1. Screws x 4
2. Telescopic flue cover set
3. Flexible flue pipe
4. Upper flue cover mounting bracket
5. Lower flue cover mounting bracket
6. Flue transition duct
7. Main body and fan housing assembly
8. Grease filters
Technical Specification
Power supply: 220-240 Volts 50Hz. Connects to 7.5A power point.
Lights: 2 x 40 watt, 240 Volt halogen
Additional items required
for installation
• Fixings required to attach rangehood body
and anti tilt points.
• Fixings required to attach flue cover
mounting brackets to the wall.
• Duct tape or cable ties.
electrolux canopy rangehood dimensions 5
Dimensions
290mm
320mm
550mm
1090mm
(maximum)
235mm
55mm
900mm
500mm
NOTE: The fan housing flue transition duct is 150mm in diameter.
(See page 10 for optional ducting accessories).
Ø150mm
6 rangehood installation electrolux canopy rangehood
Rangehood installation
1.Using a spirit level mark a vertical centre line on the wall
where the hood is to be positioned, and a horizontal line
at the hood base position (refer diagram bottom left).
NOTE: The height of the underside of the hood body must
be a minimum of 600mm above an electric cooktop &
650mm above a gas cook top and a maximum height of
800mm (refer to table below).
3. Install flue cover wall mounting brackets with suitable
fixings. Install suitable screws for rangehood mounting
points (to support a total weight of 30kg) to the wall as
marked (Fig. B).
Distance from hood base to top of hob
hob type
minimum*
maximum
gas
650mm
800mm
electric
600mm
800mm
* If the instructions of the hob specify a greater distance than the
minimum above, then that shall be the minimum height for installation
2. M
ark the location for flue cover wall mounting brackets
and rangehood mounting points and anti-tilt fixing
points above the hood base using the hood base as the
reference point (Fig. A).
250mm
Fig. B
130mm
ceiling
max. 1145mm
flue cover
wall mounting
brackets
286mm
anti-tilt fixing point
36mm
559mm
rangehood mounting
points
hood
base
250mm
580mm
Fig. A
refer table above
“Distance from hood
base to top of hob”
top
of hob
4.Remove the protective plastic film from the hood body
and hang hood on the mounting screws then secure at
the anti-tilt locations as indicated in Fig. B.
5. Fix exhaust transition duct using screws supplied (Fig. C).
Fig. C
electrolux canopy rangehood rangehood installation 7
Depending on the preferred installation/ducting mode, follow
step 6a or 6b below.
6a.Recirculating mode (Fig. D). Using the centre line,
secure the recirculating T-piece to the wall with suitable
screws/fixings (optional kit AR610RK). Install flexible pipe
between T-piece and the exhaust transition duct.
Use cable ties or suitable duct tape to secure flexible
pipe to T-piece and transition duct (Fig. F).
NOTE: When installed in recirculating mode, it is
recommended to use a carbon filter (included in
recirculation kit AR610RK) to prevent odours being
emitted back into the room.
6b.Ducted mode (Fig E.) The canopy rangehood has been
supplied with flexible flue pipe and duct transition piece,
alternatively a 150mm diameter non-combustible flue
pipe can be used. Continue the centre line to the ceiling.
Fit preferred flue pipe to the fan transition duct (Fig. F).
Use cable ties or suitable duct tape to secure flexible
pipe to the transition duct.
NOTE: For ducted mode, we recommend extending
flue pipe through the roof to external “china hat” to vent
exhaust externally. We do not recommend venting into
ceiling cavity.
NOTE: To ensure optimum performance of the
rangehood, the use of rigid ducting is recommended.
The use of bends should be avoided. Rigid flexible
ducting is suitable, although loose flexible ducting is
unacceptable. All ducting must be fire retardant.
Fig. D
Fig. E
Fig. F
7. E
lectrical connection
Check that the installation complies with the standards
of local building, gas and electrical authorities. Before
connecting to the mains supply ensure that the mains
voltage corresponds to the voltage on the rating plate
inside the rangehood.
8 rangehood installation electrolux canopy rangehood
Installation of telescopic flue covers
Separate the inner and outer flue covers, and carefully
remove the protective coating from both. Carefully
reassemble the upper and lower flue covers sections by
sliding the inner into the outer flue cover. Carefully lower
the assembled upper and lower flue covers onto the top
of the rangehood body, and insert the flue cover into the
rangehood body approximately 5mm. Fix upper flue cover
to the wall mounting bracket with screws supplied. Ensure
that the upper section is extended.
important
Care must be taken to ensure the screws are not cross
threaded when attaching the upper flue cover.
If installed in recirculating mode, insert the optional carbon
filter (included in recirculation kit AR610RK).
To complete the rangehood installation, insert the three
filters to the underside of the hood body. Place back edge
of filter into position and push up front edge so that the filter
clips into place.
Your Electrolux rangehood is now ready to use.
electrolux canopy rangehood using the rangehood 9
Using the rangehood
Touch control operation
Stainless Steel Surface
Clean stainless steel surfaces using non-abrasive cleaning
products that are specifically for use on stainless steel.
To ensure best results also use an even pressure and follow
the grain of the stainless steel. Use of a soft cloth reduces
the risk of scratching. If the cloth is wet ensure that a dry
soft cloth is used to wipe down the surface again reducing
the risk of any surface rust appearing.
fan
Fan – select speed to suit cooking conditions.
low – light frying/boiling
medium – frying/wok cooking/heavy boiling
high – grilling, intensive frying and wok cooking
To switch Lights ON and OFF
Touch the ‘light’ symbol
to turn the lights ON, if
adjustment to light intensity is required continue to touch
and hold until required brightness is achieved.
Touch ‘light’ symbol
again to turn the lights OFF.
Using the Timer
At the end of cooking, if the timer
is switched on, the
rangehood will continue to run for an additional 5 to 15
minutes, depending on the selected fan speed.
The fan speed is reduced in 5 minute increments until the
rangehood turns itself OFF.
ie. if the fan speed is set on high, it will run for 5 minutes
then reduce to medium for 5 minutes, then reduce to low
for 5 minutes before finally turning itself OFF.
This should ensure the removal of any odours that remain
after cooking.
Filter
This is the indicator/switch
to show when the filter needs
to be cleaned.
Once the filters are cleaned the “Filter” alert can be deactivated
with a single touch.
Maintenance and cleaning
caution
•B
efore maintenance or cleaning is carried out,
the canopy rangehood should be disconnected
from the main power supply. Ensure that the
rangehood is switched off at the wall socket
and the plug removed.
•E
xternal surfaces are susceptible to scratches
and abrasions, so please follow the cleaning
instructions to ensure the best possible result is
achieved without damage.
Control panel surface
The control panel can be cleaned using warm soapy water.
Ensure the cloth is well wrung before cleaning. Use a dry
soft cloth to remove any excess moisture left after cleaning.
Cleaning grease filters
The mesh filters can be cleaned by hand in warm soapy
water. Soak in warm water and some washing up liquid.
For stubborn grease stains use a soft nylon brush to help
remove these stains. After cleaning ensure that the filters
are completely dry before refitting.
Changing the halogen lamps
Ensure lamp is cool before removing
To remove the lamp, apply pressure to the lamp and turn
anti-clockwise to unscrew and remove.
Replace the lamp with one of similar type and voltage.
10 optional ducting accessories electrolux canopy rangehood
Optional ducting accessories
AR150RC
AR150F
AR610FS
AR150WV
AR610RK
AR610CF
NOTE: Accessories are to be purchased separately.
Part Numbers
Description
AR150RC
150mm G/Bond Roof Cowl
AR150F
150mm G/Bond Flue 1200mm
AR150WV
150mm Wall Vent + Flexi Duct
AR610RK
Recirculating kit (tee piece and carbon filter)
AR610CF
Replacement carbon filter
AR610FS
Stainless steel exhaust cover extension 1200mm
electrolux canopy rangehood warranty 11
Warranty
FOR SALES IN AUSTRALIA AND NEW ZEALAND
APPLIANCE: ELECTROLUX CANOPY RANGEHOOD
This document sets out the terms and conditions of product
warranties for the Electrolux canopy rangehood. It is an
important document. Please keep it with your proof of
purchase documents in a safe place for future reference
should you require service for your Electrolux appliance.
General Terms and Conditions
1. In this warranty
(a)‘Electrolux’ means Electrolux Home Products Pty Ltd ABN 51
004 762 341 in respect of Appliances purchased in Australia
and Electrolux (NZ) Limited in respect of Appliances purchased
in New Zealand;
(b)‘Appliance’ means any Electrolux product purchased by you
accompanied by this document;
(c)‘Warranty Period’ means
(i)where you use the Appliance for personal, domestic or
household purposes in Australia the period of “24” months
and in New Zealand the period of “24” months;
(ii)where you use the Appliance for commercial purposes, in
Australia the period of “3” months and in New Zealand the
period of “3” months, (if the period stated is 0 months you
are not covered by this product warranty)
following the date of original purchase of the Appliance;
(d)‘you’ means the purchaser of the Appliance not having
purchased the appliance for re-sale, and ‘your’ has a
corresponding meaning.
2.This warranty only applies to Appliances purchased and used
in Australia or New Zealand and is in addition to (and does not
exclude, restrict, or modify in any way) any non-excludable
statutory warranties in Australia or New Zealand.
3.Electrolux warrants that, when dispatched from an Electrolux
warehouse, the Appliance is free from defects in materials and
workmanship for the Warranty Period.
4. During the Warranty Period Electrolux or its Authorised Service
Centre will, at no extra charge if your appliance is readily
accessible without special equipment, and subject to these terms
and conditions, repair or replace any parts which it considers to
be defective. You agree that any replaced Appliances or parts
become the property of Electrolux. This warranty does not apply
to light globes, batteries, filters or similar perishable parts.
5. Parts and Appliances not supplied by Electrolux are not covered
by this warranty.
6.Where you are within an Electrolux service area, this warranty
covers the cost of transport of the Appliance to and from
Authorised Service Centres of Electrolux and travelling costs for
representatives of the Authorised Service Centre to and from your
home or business. If you are outside an Electrolux service area,
you will bear these costs. For information about whether you
are within an Electrolux service area, please phone 13 13 49 in
Australia, or 0800 10 66 10 in New Zealand.
7. Proof of purchase is required before you can make a claim under
this warranty.
8.You may not make a claim under this warranty unless the defect
claimed is due to faulty or defective parts or workmanship.
Electrolux is not liable in the following situations (which are not
exhaustive):
(a) The Appliance is damaged by:
(i) accident
(ii)misuse or abuse, including failure to properly maintain or
service
(iii)normal wear and tear
(iv)power surges, electrical storm damage or incorrect power
supply
(v)incomplete or improper installation
(vi)incorrect, improper or inappropriate operation
(vii) insect or vermin infestation.
(b)The Appliance is modified without authority from Electrolux in
writing.
(c)The Appliance’s serial number or warranty seal has been
removed or defaced.
(d)The Appliance was serviced or repaired by anyone other than
Electrolux or its Authorised Service Centres.
9.This warranty, the contract to which it relates and the relationship
between you and Electrolux are governed by the law applicable
in the Australian State where the Appliance was purchased or the
law applicable in New Zealand if the Appliance was purchased
in New Zealand. Where the Appliance was purchased in New
Zealand for business purposes the Consumer Guarantee Act
does not apply.
Limitation of Liability
10.To the extent permitted by law:
(a)Electrolux excludes all warranties other than as contained in
this document;
(b)Electrolux shall not be liable for any loss or damage whether
direct or indirect or consequential arising from your purchase,
use or non-use of the Appliance.
11.Provisions of the Trade Practices Act and State consumer
legislation in Australia, and the Consumer Guarantees Act, the
Sale of Goods Act and the Fair Trading Act in New Zealand, imply
warranties or conditions, or impose obligations, upon Electrolux
which cannot be excluded, restricted or modified. To the extent
permitted by law, the liability of Electrolux (if any) arising out of or
in relation to the Appliance or any services supplied by Electrolux
shall be limited (where it is fair and reasonable to do so),:
(a)in the case of Appliances, at its option, to the replacement or
repair of the Appliances or the supply of equivalent products or
the payment of the cost of replacing the Appliances or having
the Appliances repaired or of acquiring equivalent Appliances.
Upon being replaced, parts and Appliances become the
property of Electrolux; or
(b)in the case of services, at its option, to the supply of the
services again or the payment of the cost of having the services
re-supplied;
and in the case of Appliances or services supplied in New
Zealand, loss or damage whether direct or indirect or
consequential that is reasonably foreseeable.
Privacy
You acknowledge that in the event that you make a warranty claim it
will be necessary for Electrolux and its Authorised Service Centres to
exchange information in relation to you to enable Electrolux to meet its
obligations under this warranty.
Important Notice
Before Calling a Service Technician please check carefully the operating instructions, service booklet and the warranty terms and conditions.
FOR SERVICE
or to find the address of your nearest
state service centre in Australia
Please call 13 13 49
For the cost of a local call (Australia only)
FOR SERVICE
or to find the address of your nearest
authorised service centre in New Zealand
Free call 0800 10 66 10
(New Zealand only)
SERVICE AUSTRALIA
ELECTROLUX HOME PRODUCTS
www.electrolux.com.au
SERVICE NEW ZEALAND
ELECTROLUX HOME PRODUCTS
www.electrolux.co.nz
FOR SPARE PARTS
or to find the address of your nearest
state spare parts centre in Australia
Please call 13 13 50
For the cost of a local call (Australia only)
FOR SPARE PARTS
or to find the address of your nearest
state spare parts centre in New Zealand
Free call 0800 10 66 20
(New Zealand only)
Electrolux Home Products
Australia
telephone: 1300 363 640
fax:
1800 350 067
email:
customercare@electrolux.com.au
web:
www.electrolux.com.au
New Zealand
telephone: 09 573 2230
fax:
09 573 2221
email:
customercare@electrolux.co.nz
web:
www.electrolux.co.nz
The Thoughtful Design Innovator.
Do you remember the last time you opened a gift that made you say “Oh! How did
you know? That’s exactly what I wanted!” That’s the kind of feeling that the designers
at Electrolux seek to evoke in everyone who chooses or uses one of our products. We
devote time, knowledge, and a great deal of thought to anticipating and creating the
kind of appliances that our customers really need and want.
This kind of thoughtful care means innovating with insight. Not design for design’s sake,
but design for the user’s sake. For us, thoughtful design means making appliances easier
to use and tasks more enjoyable to perform, freeing our customers to experience that
ultimate 21st century luxury, ease of mind. Our aim is to make this ease of mind more
available to more people in more parts of their everyday lives, all over the world. So when
we say we’re thinking of you, you know we mean just that.
The “Thinking of you” promise from Electrolux goes beyond meeting the needs of
today’s consumers. It also means we’re committed to making appliances safe for the
environment—now and for future generations.
Electrolux. Thinking of you.
Share more of our thinking at
www.electrolux.com.au or
www.electrolux.co.nz
P/No. RH086 - Issue 1
© Copyright 2009 Electrolux Home Products Pty Ltd ABN 51 004 762 341
Print code: EEBONYRANUM
Issue date: Sep 09