advertisement
▼
Scroll to page 2
-1- M Consult the dealer or an experienced radio/television technician for help. M Connect the equipment into an outlet on a circuit different from that which the receiver is connected. M Increase the separation between the equipment and receiver. M Reorient or relocate the receiving antenna. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Subpart J of Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -2- PS/2 Keyboard and Mouse ports installed on your computer or KVM switch. System Requirements M For KVM devices that do not provide keyboard and mouse emulation M Non-powered - uses the computer’s keyboard power source M Allow keyboardless/mouseless boot and run - for increased security M Allows hot plugging of the keyboard and mouse M Prevents comptuer lockup due to keyboard signal loss with KVM switches Features Because the CV-100KM’s circuitry allows seamless and fail-safe hot plugging of the keyboard and mouse, you can hot swap the two peripherals among any number of computers at any time. The emulator works with just the keyboard or just the mouse present, as well. Simply plug the emulator into the computer’s keyboard and mouse ports, and the CV-100KM’s state-of-the-art microprocessor appears to the system as if there were an actual keyboard and mouse present. The computer boots and operates normally, with or without the presence of a real keyboard and mouse. The CV-100KM is a PS/2 keyboard and mouse emulator designed to provide a simple, inexpensive solution to common problems associeated with KVM (keyboard, video, mouse), switches. It permanently cures damaging computer lock-up commonly found in those KVM switches that do not provide keyboard and mouse emulation. With those switches, the computers ’lose’ the keyboard and/or mouse when the focus switches to a different system. Overview 1 2 3 -3- M If your keyboard does not have Wake Up capability, pressing this Wake Up switch brings the computer back from power saving mode. M If your keyboard has Wake Up capability, you can bring the computer back from power saving mode, by pressing its Wake Up key, or by tapping the Right Shift key. 1. Wake Up Switch 1 Bottom View These connectors plug into the keyboard and mouse ports of your computer. Each connector is marked with an appropriate icon to indicate which one it is. 3. Mouse and Keyboard Connectors The LEDs light to show that the peripheral has connected to the computer. The corresponding LED flashes when the keyboard or mouse transmits data. 2. Mouse and Keyboard LEDs Note: If you are using a KVM switch, the keyboard and mouse connectors from the KVM cable plug in here. The cables from your PS/ 2 Mouse and PS/ 2 Keyboard plug in here. Each port is marked with an appropriate icon to indicate which one it is. 1. Mouse and Keyboard Ports Top View -4- Installation simply entails plugging the cables into their appropriate sockets as shown in the diagrams below: Installation Static electricity may cause the unit to operate erratically. Erratic Operation 30 cm 0 ~ 50o C -20 ~ 60o C 0 ~ 80% RH Plastic Cable Length Operating Temperature Storage Temperature Humidity Housing -5- The direct vendor also reserves the right to revise or update the device or documentation without obligation to notify any individual or entity of such revisions, or update. For further inquiries, please contact your direct vendor. The direct vendor makes no warranty or representation, expressed, implied, or statutory with respect to the contents or use of this documentation, and especially disclaims its quality, performance, merchantability, or fitness for any particular purpose. IN NO EVENT SHALL THE DIRECT VENDOR’S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, DISK, OR ITS DOCUMENTATION. Limited Warranty 1 x Remote wakeup pushbutton Switches 1 x 6 pin mini-din F (to keyboard) 1 x 6 pin mini-din M (to computer) Mouse 2 1 x 6 pin mini-din F (to keyboard) 1 x 6 pin mini-din M (to computer) Keyboard Specification Unplug the CV-100KM’s cables from the computer’s keyboard and mouse ports, then reinsert them. Action LEDs Connectors Function Specifications Cause Problem Troubleshooting All brand names and trademarks are the registered property of their respective owners. © Copyright 2003 ATEN® International Co., Ltd. Manual Part No. PAPE-1227-1AT Printed in Taiwan 01/2003 If anything is damaged or missing, contact your dealer. M 1 User Manual M 1 CV-100KM PS/2 Keyboard-Mouse Emulator This package contains: Read this manual thoroughly and follow the installation and operation procedures carefully to prevent any damage to the unit, and/or any of the devices connected to it. CV-100KM User Manual
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project