Maytag MGR5765QD Specifications

Service
This manual is to be used by qualified appliance
technicians only. Maytag does not assume any
responsibility for property damage or personal
injury for improper service procedures done by
an unqualified person.
This Base Manual covers general information
Refer to individual Technical Sheet
for information on specific models
This manual includes, but is
not limited to the following:
Gas
Freestanding
Range
AGR5715QD*
AGR5735QD*
AGR5835QD*
JGR8775QD*
JGR8875QD*
MGR5754QD*
MGR5755QD*
MGR5765QD*
MGR5775QD*
MGR5875QD*
16022498
Revision 0
November 2003
Important Information
Important Notices for Servicers and Consumers
Maytag will not be responsible for personal injury or property damage from improper service procedures. Pride and
workmanship go into every product to provide our customers with quality products. It is possible, however, that during
its lifetime a product may require service. Products should be serviced only by a qualified service technician who is
familiar with the safety procedures required in the repair and who is equipped with the proper tools, parts, testing
instruments and the appropriate service information. IT IS THE TECHNICIANS RESPONSIBLITY TO REVIEW ALL
APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRS.
!
WARNING
To avoid risk of severe personal injury or death, disconnect power before working/servicing on appliance to avoid
electrical shock.
To locate an authorized servicer, please consult your telephone book or the dealer from whom you purchased this
product. For further assistance, please contact:
Customer Service Support Center
CAIR Center
Web Site
Telephone Number
WWW.AMANA.COM ................................................ 1-800-843-0304
WWW.JENNAIR.COM ............................................. 1-800-536-6247
WWW.MAYTAG.COM ............................................. 1-800-688-9900
CAIR Center in Canada ........................................... 1-800-688-2002
Amana Canada Product ........................................... 1-866-587-2002
Recognize Safety Symbols, Words, and Labels
! DANGER
DANGER—Immediate hazards which WILL result in severe personal injury or death.
!
WARNING
WARNING—Hazards or unsafe practices which COULD result in severe personal injury or death.
!
CAUTION
CAUTION—Hazards or unsafe practices which COULD result in minor personal injury, product or property
damage.
2
16022498 Rev. 0
©2003 Maytag Appliances Company
Table of Contents
Important Information .................................................. 2
Safety Information
Safety Practices for Servicer .................................. 5
Servicing .............................................................. 5
Receiving Oven ..................................................... 5
ALL APPLIANCES ................................................ 5
SELF-CLEANING OVEN........................................ 5
OVEN .................................................................. 6
Delayed Ignition .................................................... 6
Precautions .......................................................... 6
In Case of Fire ...................................................... 6
Using the Oven ..................................................... 6
Baking, Broiling, and Roasting ............................... 7
Connecting Range to Gas ...................................... 7
Electrical Requirements ......................................... 8
Extension Cord ..................................................... 8
Grounding ............................................................. 8
Product Safety Devices .......................................... 9
General Information
Cooking Nomenclature ......................................... 10
Rating label ........................................................ 11
Functional Operation ........................................... 11
Specifications ..................................................... 12
Model Identification .............................................. 12
Service ............................................................... 12
Parts and Accessories ........................................ 12
Extended Service Plan ......................................... 12
Troubleshooting Procedures ..................................... 13
Testing Procedures .................................................. 16
H1 Control .......................................................... 20
M1 Control .......................................................... 24
M2 Control .......................................................... 25
©2003 Maytag Appliances Company
Disassembly Procedures
Removing and Replacing Range ........................... 29
Front Control Panel ............................................. 29
Maintop Assembly .............................................. 29
Control Panel ...................................................... 29
Control Board Assembly ...................................... 29
Rocker Switch .................................................... 29
Top Surface Valve and Spark Switch..................... 29
Top of Surface Burner .......................................... 29
Bottom of Surface Burner ..................................... 29
Oven Sensor ....................................................... 30
Convection Fan Assembly .................................... 30
Bake Burner and Ignitor ....................................... 30
Broiler Burner and Ignitor ..................................... 30
Valve / Regulator Assembly ................................. 30
Automatic Oven Door Latch Assembly .................. 30
Spark Module ..................................................... 30
Door Plunger Light Switch.................................... 31
Oven Door Removal ............................................. 31
Oven Door Hinge Receptacle ................................ 31
Side Panel Removal ............................................ 31
Backguard .......................................................... 31
Storage Drawer and
Storage Drawer Panel Removal ......................... 31
Storage Drawer Track Removal ............................. 32
Oven Light Assembly ........................................... 32
Frameless Door Disassembly .............................. 32
Power Cord ......................................................... 32
Appendix A
Gas Conversion .................................................. A-2
Surface Burners to LP/Propane Gas .................... A-3
LP Gas Surface Burner Orifice Configuration ........ A-4
Natural Gas Surface Burner Orifice Configuration .. A-5
Converting Bake Burner Orifice ............................ A-6
Converting Broil Burner Orifice ............................. A-8
Low Flow Conversion For Surface Burner Valves ... A-9
16022498 Rev. 0
3
Safety Information
As with all appliances, there are certain rules to follow for
safe operation. Verify everyone who operates the range is
familiar with the operations and with these precautions.
Use appliance only for its intended purpose as described.
Pay close attention to the safety sections of this manual.
Recognize the safety section by looking for the symbol
or the word safety.
!
WARNING
This gas appliance contains or produces a chemical or
chemicals which are known to the state of California to
cause cancer, birth defects or other reproductive harm.
To reduce the risk from substances in the fuel or from
fuel combustion make sure this appliance is installed,
operated, and maintained according to the instructions
in this manual.
Recognize this symbol as a safety precaution.
Due to the nature of cooking, fires can occur as a
result of overcooking or excessive grease. Although a
fire is unlikely, if one occurs proceed as follows:
!
!
WARNING
If the information in this manual is not followed exactly,
a fire or explosion may result causing property
damage, personal injury or death.
Do not store or use gasoline or other flammable vapors
or liquids in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Extinguish any open flame.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire
department.
Installation and service must be performed by an
authorized installer, service agency or gas supplier.
!
Oven Fires
1. Do not open the oven door.
2. Turn all controls to the OFF position.
3. As an added precaution turn off the electricity at
the main circuit breaker or fuse box and the gas
at the main supply valve.
4. Allow the food or grease to burn itself out in the
oven.
If smoke or fire persist call the local fire department.
To avoid risk of property damage or personal injury do
not obstruct the flow of combustion or ventilation air to
the oven.
To avoid risk of electrical shock, serious personal injury
or death: Verfiy the oven has been properly grounded
and always disconnect the electrical supply before
servicing this unit.
NOTE: The maximum gas supply pressure for these
models must not exceed 14 inches W.C.P.
WARNING
To avoid risk of electrical shock, property damage,
personal injury or death; verify wiring is correct, if
components were replaced. Verify proper and complete
operation of unit after servicing.
4
16022498 Rev. 0
©2003 Maytag Appliances Company
Safety Information
Safety Practices for Servicer
Safe and satisfactory operation of gas ranges depends
upon its design and proper installation. However, there is
one more area of safety to be considered:
Servicing
Listed below are some general precautions and safety
practices which should be followed in order to protect the
service technician and consumer during service and after
service has been completed.
1. Gas smell—Extinguish any and all open flames and
open windows.
2. Turn gas off—Service range with gas turned off
unless testing requires it.
3. Checking for gas leaks—Never check for leaks with
any kind of open flame. Soap and water solution
should be used for this purpose. Apply solution to
suspected area and watch for air bubbles which
indicates a leak. Correct leaks by tightening fittings,
screws, connections, applying approved compound,
or installing new parts.
4. Using lights—Use a hand flashlight when servicing
ranges or checking for gas leaks. Electric switches
should not be operated where leaks are suspected.
This will avoid creating arcing or sparks which could
ignite the gas. If electric lights are already turned on,
they should not be turned off.
5. Do not smoke—Never smoke while servicing gas
ranges, especially when working on piping that
contains or has contained gas.
6. Check range when service is completed—After
servicing, make visual checks on electrical
connection, and check for gas leaks. Inform
consumer of the condition of range before leaving.
7. Adhere to all local regulations and codes when
performing service.
Receiving Range
• Installer needs to show consumer location of the range
gas shut-off valve and how to shut it off.
• Authorized servicer must install the range, in
accordance with the Installation Instructions.
Adjustments and service should be performed only by
authorized servicer.
• Plug range into a 120–volt grounded outlet only. Do not
remove round grounding prong from the plug. If in doubt
about grounding of the home electrical system, it is
consumers responsibility and obligation to have an
ungrounded outlet replaced with a properly grounded
three-prong outlet in accordance with the National
Electrical Code. Do not use an extension cord with this
appliance.
• Insure all packing materials are removed from the range
before operating it, to prevent fire or smoke damage
should the packing material ignite.
©2003 Maytag Appliances Company
• Ensure range is correctly adjusted by a qualified
service technician or installer for the type of gas
(Natural or LP). Some ranges can be converted for use
with Natural or LP gas.
• With prolonged use of a range, high floor temperatures
could result. Many floor coverings will not be able to
withstand this kind of use. Never install range over vinyl
tile or linoleum that cannot withstand high
temperatures. Never install range directly over
carpeting.
ALL APPLIANCES
1. Proper Installation—Be sure your appliance is
properly installed and grounded by a qualified
technician.
2. Never Use Appliance for Warming or Heating the
Room.
3. Do Not Leave Children Alone—Children should not be
alone or unattended in the area where the appliance
is in use. They should never be allowed to sit or stand
on any part of the appliance.
4. Wear Proper Apparel—Loose fitting or hanging
garments should never be worn while using appliance.
5. User Servicing—Do not repair or replace any part of
the appliance unless specifically recommended in the
manual. All other servicing should be referred to a
qualified technician.
6. Storage in or on Appliance—Flammable materials
should not be stored in oven.
7. Do Not Use Water on Grease Fires—Smother fire or
flame, or use dry chemical or foam-type extinguisher.
8. Use Only Dry Potholders—Moist or damp potholders
on hot surfaces may result in burns from steam. Do
not let potholder touch burners. Do not use a towel or
other bulky cloth.
SELF-CLEANING OVEN
1. Do Not Clean Door Gasket—The door gasket is
essential for a good seal. Care should be taken not to
rub, damage, or move the gasket.
2. Do Not Use Oven Cleaners—No commercial oven
cleaner or oven liner protective coating of any kind
should be used in or around any part of the liner.
3. Clean Only Parts Listed in Manual. See Cleaning
section.
4. Before Self-Cleaning the Oven—Remove broiler pan,
oven racks, and other utensils.
5. Remove all items from oven top and backguard.
16022498 Rev. 0
5
Safety Information
OVEN
In Case of Fire
1. Use Care When Opening Door—Let hot air or steam
escape before removing or replacing food.
Fires can occur as a result of over cooking or excessive
grease. Though a fire is unlikely, if one occurs, proceed
as follows:
2. Do Not Heat Unopened Food Containers—Build-up of
pressure may cause container to burst and result in
injury.
3. Keep Oven Vents Ducts Unobstructed.
4. Placement of Oven Racks—Always place oven racks
in desired location while oven is cool. If rack is
removed while oven is hot, do not let potholder
contact hot heating element in oven.
2. Turn oven control to OFF.
3. As an added precaution, turn off gas supply and
power at main circuit breaker or fuse box.
4. Turn on vent to remove smoke.
5. Allow food or grease to burn itself out in oven.
Delayed Ignition
Bake Burner Flame
Allow no more than 40–60 seconds before burner ignites
and heat is felt. To check for heat, open oven door to first
stop and place hand over oven door. If heat is not felt,
cancel bake funtion. If burner repeatedly fails to ignite,
contact an authorized servicer.
Broiler Flame
Allow no more than 40–60 seconds before burner ignites
and flame is seen. If burner does not ignite cancel broil
function. If burner repeatedly fails to ignite within 40–60
seconds contact an authorized servicer.
Radiant screen style broiler flame should appear hazy or
fuzzy. Haze should be no more than 3/8–inch thick. The
radiant screen should begin to glow red within 1–2
minutes.
Precautions
• Do not mix household cleaning products. Chemical
mixtures may interact with objectionable or even
hazardous results.
• Do not put plastic items on warm cooking areas. They
may stick and melt.
• Do not use damp sponge or dishcloth to clean oven
when oven is hot. Steam from sponge or dishcloth can
burn.
• Do not leave fat heating unless you remain nearby. Fat
can ignite if overheated by spilling onto hot surfaces.
6
Oven Fires
1. If you see smoke from oven, do not open oven door.
6. If smoke and fire persist, call fire department.
7. If there is any damage to components, call repair
service before using oven.
If smoke or fire persist call the local fire department.
To avoid the risk of property damage or personal injury do
not obstruct the flow of combustion or ventilation air to
the oven.
To avoid the risk of electrical shock, serious personal
injury or death: Make sure your oven has been properly
grounded and always disconnect the electrical supply
before servicing this unit.
NOTE: The maximum gas supply pressure for these
models must not exceed 14 inches W.C.P.
Using the Oven
• Do not leave children alone or unattended where a
range is hot or in operation. They could be seriously
burned.
• Do not allow anyone to climb, stand or hang on the
door. They could damage the range and cause severe
personal injury.
• Wear proper apparel. Loose fitting or hanging garments
should never be worn when using oven. Flammable
material could ignite if brought in contact with flame or
hot oven surfaces which may cause severe burns.
• Never use range for warming or heating a room. This
may cause burns, injuries, or a fire.
• Do not use water on grease fires.
• Do not let grease or other flammable materials collect
in or around range.
• Do not repair or replace any part of range unless it is
recommended in this manual.
• Use only dry potholders. Moist or damp potholders
used on hot surfaces may result in a burn from steam.
Do not let a potholder touch the flame. Do not use a
towel or a bulky cloth as a potholder.
• Never leave range unattended while cooking. Boilovers
can cause smoking and may ignite.
16022498 Rev. 0
©2003 Maytag Appliances Company
Safety Information
• Only certain types of glass/ceramic, earthenware, or
other glazed utensils are suitable for oven use.
Unsuitable utensils may break due to sudden
temperature change.
• Use care when opening oven door. Let hot air or steam
escape before removing or replacing food.
• Do not heat unopened food containers in oven.
Build-up of pressure may cause a container to burst
and result in injury.
• Keep range vent ducts unobstructed.
• Place oven racks in desired location while oven is cool.
If a rack must be moved while oven is hot, use a dry
potholder.
• Do not use aluminum foil to line oven bottom or racks.
Aluminum foil can cause a fire and will seriously affect
baking results, and damage to porcelain surfaces.
• Do not touch interior surfaces of oven during or
immediately after use. Do not let clothing or other
flammable materials come in contact with bake or broil
burners.
• Other areas of the oven can become hot enough to
cause burns, such as vent openings, window, oven door
and oven racks.
• To avoid steam burns, do not use a wet sponge or cloth
to wipe up spills on hot cooking area.
• Do not store combustible or flammable materials, such
as gasoline or other flammable vapors and liquids near
or in oven.
• Do not clean oven door gasket located on back of the
door. Gasket is necessary to seal the oven and can be
damaged as a result of rubbing or being moved.
• Do not drape towels or any materials on oven door
handles. These items may ignite causing a fire.
!
Baking, Broiling, and Roasting
• Do not use oven area for storage.
• Stand back from range when opening door of a hot
oven. Hot air or steam can cause burns to hands, face,
and eyes.
• Do not use aluminum foil anywhere in the oven. This
could result in a fire hazard and damage the range.
• Use only glass cookware appropriate for use in gas
ovens.
• Always remove broiler pan from oven when finished
broiling. Grease left in pan can catch fire if oven is used
without removing grease from the broiler pan.
• When broiling, meat that is close to the flame, may
ignite. Trim any excess fat to help prevent excessive
flare-ups.
• Make sure broiler pan is placed correctly to reduce any
possibility of grease fires.
• Should a grease fire occur in the broiler pan, turn off
oven, and keep oven door closed until fire burns out.
Connecting Range to Gas
Install manual shut-off valve in gas line for easy
accessibility outside range. Be aware of the location of
the shut-off valve.
CAUTION
Do not store items of interest to children in cabinets
above range. Children may climb on oven to reach
these items and become seriously injured.
©2003 Maytag Appliances Company
16022498 Rev. 0
7
Safety Information
Electrical Requirements
120-volt, 60 Hertz, 15 amp, individual circuit which is
properly grounded, polarized and protected by a circuit
breaker or fuse.
Extension Cord
Due to possible pinching during installation, extension
cords should not be used on products.
Extension cords will adversely affect the performance of
spark system.
Grounding
NOTE: This appliance must be properly grounded, for
personal safety.
Power cord on this appliance is equipped with a threeprong grounding plug. This matches standard three-prong
grounding wall receptacle to prevent possibility of electric
shock from this appliance.
Consumer should have wall receptacle and circuit
checked by qualified electrician to verify receptacle is
properly grounded.
!
WARNING
Attaching adapter ground terminal to wall receptacle
cover screw does not ground appliance unless the
cover screw is metal and not insulated, and wall
receptacle is grounded through the house wiring.
Consumer should have circuit checked by a qualified
electrician to verify receptacle is properly grounded.
When disconnecting power cord from adapter, always
hold adapter with one hand. If this is not done, adapter
ground terminal is very likely to break with repeated use.
Should this happen, DO NOT USE appliance until a
proper ground has been established.
Neutral Wire
Where standard two-prong wall receptacle is
encountered, it is consumers responsibility and
obligation to have it replaced with a properly grounded
three-prong wall receptacle.
Ground
Hot Line
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR
REMOVE THE THIRD (GROUND) PRONG FROM
POWER CORD.
For 15 amp circuits only. Do not use an adapter on 20
amp. circuit. Where local codes permit, a TEMPORARY
CONNECTION may be made to properly grounded twoprong wall receptacle by the use of a UL listed adapter
available at most hardware stores.
Larger slot on adapter must be aligned with larger slot in
the wall receptacle to provide proper polarity.
8
NOTE: Circuit tester can be use to verify voltage is
present at the outlet, connect one lead to hot
line and the other lead to ground, circuit tester
should light.
16022498 Rev. 0
©2003 Maytag Appliances Company
Safety Information
Product Safety Devices
Safety devices and features have been engineered into the product to protect consumer and servicer. Safety devices
must never be removed, bypassed, or altered in such a manner as to defeat the purpose for which they were intended.
Listed below are various safety devices together with the reason each device is incorporated in the gas ranges.
Pressure Regulator
Maintains proper and steady gas pressure for operation of oven controls. Regulator
must be set for the type of gas being used Natural or LP. After servicing regulator,
make certain it is set properly before completing service.
Gas Burner Orifices
These products use a fixed orifice fitting that must be installed for Natural or LP.
After servicing a valve or orifice verify it is properly operating before completing
service.
Oven Safety Valve
Oven valve is designed to be a safety valve. Two basic designs are used in gas
ranges.
Hydraulic type valve
Electric type valve
Both types are safety valves because they are indirectly operated by the oven
thermostat, which controls a pilot flame or electric ignitor, to open and close the oven
valve.
These products use the Electric Type Valve.
Grounded Oven Frame
Ground prong on power cord is connected to the frame, usually a green lead fastened
by a screw. In addition, any part or component capable of conducting an electric
current is grounded by its mounting.
If any ground wire, screw, strap, nut, etc. is removed for service, or any reason, it
must be reconnected to its original position with original fastener before the appliance
is put into operation again.
Failure to do so can create a possible shock hazard.
©2003 Maytag Appliances Company
16022498 Rev. 0
9
General Information
This manual provides basic instructions and suggestions
for handling, installing , and servicing gas ranges.
The directions, information, and warnings in this manual
are developed from experience with, and careful testing of
the product. If the unit is installed according to the
Installation Instructions, it will operate properly and will
require minimal servicing. A unit in proper operating order
ensures the consumer all the benefits provided by
efficient gas cooking.
This manual contains information needed by authorized
service technicians to install and service gas ranges
pertaining to this manual. There maybe, however some
information which needs further explanation. Refer to
individual Installation Instructions, Use and Care,
Technical Sheets, or toll free technical support line to
answer questions from authorized service technicians.
Cooking Nomenclature
A
G
R
5
7
1
5
Q
D
W
Color
A
B
C
H
L
P
Q
S
T
W
F
N
Brand
A
C
G
H
J
M
N
U
Y
Amana
Magic Chief
Graffer &
Sattler
Hardwick
Jenn-Air
Maytag
Norge
Universal
Crosley
Listing
Fuel
B
D
E/J
G
L
M
P
X
W
Almond on Almond
Black
Brushed Chrome
Traditional White
Traditional Almond
Prostyle
Monochromatic Bisque
Stainless
Traditional Bisque
White on White
Frost White (True Color White)
Natural Bisque (True Color Bisque)
A
C
D
G
M
P
Butane
Dual Fuel
Electric
Gas, Natural
Liquid Propane
Microwave
Standing Pilot
No Fuel
Warming Drawer
X
UL/AGA
CSA/CGA/CUL
Dual Listed
220-240 V / 50-60 Hz
Military Model
PSB Approved
(Singapore)
Export 120 V / 60 Hz
Production Code
This identifies which
version of production the
unit is.
Product Type
A
C
D
E
G
L
M
P
Q
R
S
T
V
W
Y
Z
10
Accessory/Cartridge
Cooktop Updraft/Countertop
Downdraft Cooktop or Warming Drawer
Eyelevel Range
Grill
Range (20")
Range (36")
Drop In (24")
Wall Oven (27")
Range, Free-Standing (30")
Slide-In (30")
Range Hood
OTR
Wall Oven
RV Range
RV Top
Feature Content
1000-3999
4000-6999
7000-9999
16022498 Rev. 0
Brands
Maytag/Amana
Jenn-Air
©2003 Maytag Appliances Company
General Information
Rating Label
Model numbers are recorded on the rating label. Rating
label is located on the lower front right corner of the oven
frame. It can be seen by opening the oven door. Before
ordering parts, write down the correct model and serial
number from rating label. This avoids incorrect shipments
and delays. Please refer to parts reference material when
ordering replacement parts.
Functional Operation
The glow bar system is completely reliant upon
electricity. When the oven control is turned on, 120 VAC
is provided to the glow bar ignitor and the gas valve
circuit. The high resistances of the glow bar limits the
current flow through the ignitor/gas valve. Continual
current flow through the circuit causes the glow bar
ignitor to glow brighter and the resistance of the ignitor
decreases, which increases the current flow through the
ignitor/gas valve circuit. This increases the amount of
heat generated by the heater, which causes the bi-metal
to bend.
©2003 Maytag Appliances Company
At a point the ignitor resistance will have increased to
approximately 3.5 amps of current flow through the
ignitor/gas valve circuit. In approximately 45 seconds the
glow bar ignitor temperature will have increased to
approximately 2650°F. the voltage drop across the gas
valve terminals will have increased to about 3 VAC, which
will indicate enough current to flow to provide enough
bi-metal heat to cause the gas valve to open providing
gas flow to the oven burner the heat from the glow bar
ignites the gas. The sensing element of the oven control
then cycles contacts within the oven control, opening and
closing to cycle the glow bar, safety valve, and burner to
maintain the desired temperature.
NOTE: This system cannot operate without electricity.
The primary components of this ignition system are:
electronic control, ignitor, and safety valve. These
components are all wired in series and although the oven
control and glow bar require 120 VAC, 60 Hz. The oven
valve operates on approximately 3 volts.
Therefore, 120 VAC should never be applied directly to
the oven valve terminals. The glow bar is the power
source for the oven valve.
16022498 Rev. 0
11
General Information
Specifications
Parts and Accessories
Refer to individual Technical Sheet for information
regarding specifications.
Purchase replacement parts and accessories over the
phone. To order accessories for your product call:
Model Identification
Complete registration card and promptly return. If
registration card is missing:
• For Amana product call 1-800-843-0304 or visit the
Web Site at www.amana.com
• For Maytag product call 1-800-688-9900 or visit the
Web Site at www.maytag.com
• For Jenn-Air product call 1-800-536-6247 or visit the
Web Site at www.jennair.com
• For product in Canada call 1-866-587-2002 or visit the
Web Sites at www.amana.com or www.maytag.com or
www.jennair.com
When contacting provide product information located on
rating plate. Record the following:
Model Number:
Manufacturing Number:
Serial or S/N Number:
Date of purchase:
Dealer’s name and address:
___________________
___________________
___________________
___________________
___________________
• For Amana product call 1-877-232-6771 or visit the
Web Site at www.amana.com
• For Maytag/Jenn-Air product call 1-800-462-9824 or
visit the Web Site at www.maytag.com or
www.jennair.com
• For product in Canada call 1-866-587-2002 or visit the
Web Sites at www.amana.com or www.maytag.com or
www.jennair.com
Extended Service Plan
We offer long-term service protection for this new oven.
• Asure™ Extended Service Plan is specially designed
to supplement Amana’s strong warranty. This plan
covers parts, labor, and travel charges.
Call 1-866-232-6244 for information.
• Dependability PlusSM Extended Service Plan is
specially designed to supplement Maytag’s and
Jenn-Air’s strong warranty. This plan covers parts,
labor, and travel charges.
Call 1-800-925-2020 for information.
Service
Keep a copy of sales receipt for future reference or in
case warranty service is required. To locate an authorized
servicer:
• For Amana product call 1-800-628-5782 or visit the
Web Site at www.amana.com
• For Maytag/Jenn-Air product call 1-800-462-9824 or
visit the Web Site at www.maytag.com or
www.jennair.com
• For product in Canada call 1-866-587-2002 or visit the
Web Sites at www.amana.com or www.maytag.com or
www.jennair.com
Warranty service must be performed by an authorized
servicer. We also recommend contacting an authorized
servicer, if service is required after warranty expires.
12
16022498 Rev. 0
©2003 Maytag Appliances Company
Troubleshooting Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires it.
Problem
Burners will not ignite; no
spark at top burner.
Possible Cause
Poor ground on burner cap .........................
Weak or failed spark module.......................
Low gas pressure ........................................
No 120 VAC to range ..................................
Micro switch contacts not closing................
Burner will not ignite. No
spark to burner ignitors
when burner knob is rotated
to “LITE” position.
Faulty wiring. Bad connection at burner
electrode and electrode socket ...................
Inoperative spark module............................
Electrode dirty. Burner cap dirty..................
Cracked or broken electrode, electrode
wire or electrode socket ..............................
No spark or only random
spark at one ignitor.
Check for cracked ignitor or pinched ignitor
wire .............................................................
Poor continuity to burner cap ......................
Bad ground connection or lack of continuity
to ground or ignitor ......................................
Cracked or broken ignitor extension lead ...
Shorted valve switch/harness .....................
Unit continues to spark after
knob is turned to OFF
position.
Switch has slipped off the valve ..................
No voltage to control. ..................................
No oven operation in bake or
broil.
No voltage from control ...............................
Loose wire connection or broken wire.........
©2003 Maytag Appliances Company
16022498 Rev. 0
Correction
• Clean burner cap.
• Replace spark module.
• Verify pressure 4” WCP for
natural, 10” WCP for LP.
• Verify voltage at wall outlet.
• Check wiring against appropriate
wiring diagram, Verify all
terminals and connections are
correct and tight. Check micro
switch contacts.
• Check wiring against appropriate
wiring diagram. Verify all
terminals and connections are
correct and tight.
• Check module according to
testing procedures information.
• Clean electrode or burner cap.
• Replace electrode.
• Replace ignitor lead or electrode.
• Clean burner cap and lead.
• Tighten ground connection and
correct any breaks in ground path
from ignitor path to unit ground
path.
• Replace ignitor lead.
• Replace switch/harness. If
shorting is caused by excessive
spillovers, customer education is
advised.
• Carefully reposition switch on
valve and rotate from OFF to
high, several times to verify
switch is not broken.
• Check for 120 VAC at control. If
no voltage check power source.
• Check 120 VAC to ignitor, if no
voltage, replace control.
• Verify all connections are clean
and tight, replace broken wire.
13
Troubleshooting Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires it.
Problem
Possible Cause
Failed ignitor. ...............................................
•
Gas pressure too high .................................
•
Failed gas valve ..........................................
Loose wire connection or broken wire.........
•
•
Ignitor positioned too far from burner ..........
•
Dirt or grease in orifice or burner ................
Insufficient gas pressure .............................
•
•
Power outage ..............................................
•
No gas flows to burner.
Ignitor glows red.
Gas flows to bake/broil
burner, but burner does not
light.
•
Power outage ..............................................
Broil burner shuts off shortly
after the start of self-clean
operation. Bake and broil
functions operate normally.
•
•
•
No power to fan motor.................................
•
Failed fan motor or winding or frozen shaft.
•
Fan motor does not operate.
14
16022498 Rev. 0
Correction
Check ignitor current draw, 3.2 –
3.6 Amps. Replace ignitor, if it
fails test.
Check for correct gas pressure.
Natural gas pressure should be
4" WCP and LP gas pressure
should be 10" WCP.
Check gas valve for continuity.
Verify all connections are clean
and tight, replace broken wire.
Reposition ignitor closer to
bake/broil burner.
Clean orifice or burner.
Check for correct gas pressure.
Natural gas pressure should be
4" WCP and LP gas pressure
should be 10" WCP.
Verify power is present at unit.
Verify that the circuit breaker is
not tripped.
Replace household fuse, but do
not fuse capacity.
Verify power is present at unit.
Verify that the circuit breaker is
not tripped.
Replace household fuse, but do
not fuse capacity.
Refer to Use and Care Manual
“Operating Instructions”, if
continues contact service.
Check for 120 VAC supplied at
fan motor. If no voltage is
present, check for broken or
loose wiring between fan motor
and relay board. If voltage is
present at fan motor, go to the
next step.
Check motor winding for
continuity. Check for a frozen
motor shaft. Check for broken
wiring between motor and neutral
terminal block.
©2003 Maytag Appliances Company
Troubleshooting Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires it.
Problem
Oven light does not operate.
Possible Cause
Failed oven lamp .........................................
•
Failed wiring ................................................
•
Failed light socket........................................
Failed light plunger/switch...........................
•
•
Programming error ......................................
•
Oven is self-cleaning ...................................
Oven is still hot ............................................
•
•
Normal.........................................................
•
Self-clean cycle not working
Oven door will not unlock
Oven smokes/odor first few
times of usage
Failure Codes
©2003 Maytag Appliances Company
•
Electronically Controlled..............................
16022498 Rev. 0
•
Correction
Check lamp and replace is
necessary.
Check for broken, loose or dirty
connections.
Check light socket for continuity.
Check plunger/switch for
continuity. Check wiring diagram
for application.
Shut off power to oven for five
minutes by switching off circuit
breaker. Reset circuit breaker
and try oven again.
Allow cycle to complete.
Door will not unlock until unit has
cooled to safe temperature. Do
not force door open, this will void
warranty. Blow cool air on door
latch area to quicken process.
Minor smoking and/or odor is
normal the first few times of oven
usage.
Ventilate area well and perform
self-clean cycle.
See Testing Procedures for
diagnostic checks.
15
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
Illustration
Component
Oven light socket
Door plunger switch
NC
C
Test Procedure
Test continuity of receptacle terminals.
Results
Indicates continuity with bulb screwed in.
Measure voltage at oven light.
120 VAC, see wiring diagram for terminal
identification.
If no voltage is present at oven light
check wiring.
Remove switch from unit and measure
the following points:
C-NO
Plunger in continuity, Plunger out infinite.
Measure continuity of switch positions:
Closed ..............................................
Open .................................................
Continuity
Infinite
NO
Rocker switch
Door light switch
NC
NO
COM
Autolatch assembly
with switch
Switch connection in following
positions:
Not engaged
Engaged
Disconnect wires and test for
continuity per wiring diagram.
Normally Open
COM-NO=Open, COM-NC=Closed
COM-NO=Closed, COM-NC=Open
See wiring diagram for schematic layout.
Refer to Parts Manual for correct
autolatch switch.
Bake burner
Verify gas is supplied.
Orifice adjusted for Natural or LP.
Check for obstructions, contamination
in ports or damage.
Verify gas is supplied.
Replace if punctured or torn.
Verify proper orifice installed for
Natural or LP.
Clean with hot soapy water and dry
completely.
Replace if punctured or torn.
Ignitor
Check for obstructions, contamination
in ports or damage.
Test for voltage at terminals ...............
Temperature sensor
Test for the amount of amperage in the
circuit..................................................
(Ignitor may glow, but not have
sufficient amperage to open valve).
Measure resistance.
Convection motor fan
Verify supply voltage ........................
120 VAC
Convection element
Measure continuity at the following
points:
Terminal to terminal..........................
Terminal to ground ...........................
Test continuity of terminals...............
Continuity
Infinite
Approximately 14 Ω - cold
Test voltage to terminals ..................
120 VAC
Broil burner
16
Clean with hot soapy water and dry
completely.
16022498 Rev. 0
120 VAC
3.2−3.6 Amps.
Approximately 1100 Ω at room
temperature 80ºF.
©2003 Maytag Appliances Company
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
Illustration
Component
Pressure regulator
Test Procedure
Verify gas pressure (WCP).
If on LP service, verify proper gas
supply conversion.
Spark module
4+0
GND
Test for voltage at terminals
L and N...........................................
Polarity and ground ........................
Input
L or N
Holder orifice
Results
4" Natural
10" LP/Propane
120 VAC
Not subject to polarity
Verify gas pressure (WCP).
4" Natural
10" LP/Propane
Spark ignition
electrode
270° valve
Check orifice for debris.
Clean as needed.
Test for resistance of spark lead ..........
Continuity
Test ignitor to chassis ..........................
No continuity from ignitor to chassis.
Verify gas is supplied.
Verify Orifice for
Natural or LP.
Spark 270° switch
Top surface burner
Adjust set screw for simmer control.
Unplug switch harness at rear of
range. Test for continuity at wire
terminals.
Switch in LITE position .......................
Switch in any other position................
Verify gas is supplied ...........................
Fixed orifices for Natural or LP.
See conversion section.
120 VAC
Continuity
Infinite
Check for obstructions in burner ports.
Verify burner cap is positioned
correctly.
©2003 Maytag Appliances Company
16022498 Rev. 0
17
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
Illustration
Matrix
Control Panel Assembly
Test Procedure
Continuity is indicated as follows:
1000 – 6600 Ω for Cancel pad
1000 – 15000 Ω for All other pads
16
9
8
1
Matrix
Control Panel Assembly
Continuity is indicated as follows:
1000 – 6600 Ω for Cancel pad
1000 – 15000 Ω for All other pads
16
9
8
1
18
16022498 Rev. 0
Results
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Clock
Cook & Hold
Broil
Bake
Clean
Keep Warm
Favorites
Timer
Light
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Clock
Cook & Hold
Broil
Bake
Convect
Clean
Keep Warm
Favorites
Timer
Light
Trace
13 & 15
12 & 15
10 & 15
7 & 13
12 & 13
10 & 12
4 & 13
4 & 12
4 & 10
5 & 12
1&2
5 & 14
15 & 14
4&5
7 & 15
13 & 14
7 & 14
5 & 13
4 & 14
12 & 11
Trace
5 & 14
4 & 14
4 & 13
4 & 12
4 & 10
13 & 14
4&5
5 & 13
5 & 12
5 & 10
1&2
13 & 15
12 & 11
7 & 15
7 & 14
10 & 11
10 & 12
4&7
10 & 15
12 & 13
12 & 15
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
©2003 Maytag Appliances Company
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
Illustration
Matrix
Control Panel Assembly
Test Procedure
Continuity is indicated as follows:
1000 – 6600 Ω for Cancel pad
1000 – 15000 Ω for All other pads
16
9
8
1
Matrix
Control Panel Assembly
Continuity is indicated as follows:
1000 – 6600 Ω for Cancel pad
1000 – 15000 Ω for All other pads
16
9
8
1
©2003 Maytag Appliances Company
16022498 Rev. 0
Results
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Convect Bake
Convect Roast
Keep Warm
Bake
Broil
Clean
Drying
Proofing
Timer
Clock
Cook & Hold
Favorite
Light
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Clock
Cook & Hold
Broil
Bake
CV Bake
CV Roast
Clean
Keep Warm
Favorites
Timer
Light
Trace
13 & 15
12 & 15
10 & 15
7 & 13
12 & 13
10 & 12
4 & 13
4 & 12
4 & 10
5 & 12
1&2
7 & 11
11 & 13
4&7
7 & 15
4&5
5&7
11 & 12
5 & 10
4 & 11
5 & 11
11 & 15
5 & 13
10 & 11
Trace
13 & 15
12 & 13
12 & 15
4 & 11
4 & 12
4 & 10
5 & 13
5 & 12
5 & 10
10 & 12
1&2
4&5
4&7
5&7
10 & 11
4 & 13
7 & 11
7 & 15
11 & 12
13 & 14
5 & 11
7 & 13
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
19
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
Illustration
H1 Controlled
Component
Oven temperature
adjustment
H1 Controlled
Temperature display
H1 Controlled
Clock Display
H1 Controlled
24 Hour Clock
H1 Controlled
Factory Default
H1 Controlled
Twelve hour off
H1 Controlled
Sabbath Mode
Test Procedure
Press BAKE pad.
Enter 550 on the digit-pad.
Immediately press and hold BAKE
pad for 3 seconds.
Oven can be adjusted from -35 to +35
degrees in 5-degree increments by
pressing AUTOSET pad. To avoid
over adjusting the oven, move
temperature 5 degrees each time.
Wait 4 seconds for the data entry timer
to expire to accept the change.
Temperature adjustment will be
retained even through a power failure.
Press and hold Cancel and Bake
pads for 3 seconds.
Press and hold Cancel and Clock
pads for 3 seconds.
Press and hold Cancel and Favorite
pads for 3 seconds.
Press and hold Cancel and Keep
Warm pads for 3 seconds.
Control will automatically cancel any
cooking operation and remove all
relay drives 12 hours after the last pad
touch.
Hold CLOCK pad for 3 seconds to
activate Sabbath mode.
Hold CLOCK pad for 3 seconds to
disable Sabbath mode.
H1 Controlled
H1 Controlled
20
Child lock out
Diagnostic Code
Display
Press and hold Cancel and Cook &
Hold pads for 3 seconds. “OFF” will
display where the temperature
normally appears. “LOCK” will display
flashing while door is locking.
To reactivate the control, press and
hold Cancel and Cook & Hold pads
for 3 seconds.
See “Quick Test Mode”.
Cycle through the codes using the
number pads 1 through 5.
16022498 Rev. 0
Results
While increasing or decreasing oven
temperature, this does not affect selfcleaning temperature.
This mode enables the user to indicate
°F or °C on the display.
Allows clock to be toggled On or OFF.
Allows the time on the clock to be
toggled from 12 hour or 24 hour display.
Allows the clock to be reset to factory
settings.
See Sabbath mode to disable.
“SAb” will be displayed and flash for 5
seconds.
Display will go back to time of day.
All pad inputs are disabled except for
CANCEL and CLOCK pads.
This mode disables the normal 12 hour
shutoff to allow operation of the bake
mode for a maximum of 72 hours.
This is a safety feature that can be used
to prevent children from accidentally
programming the oven. It disables the
electronic oven control.
Child lockout features must be reset after
a power failure.
The last 5 diagnostic codes will be stored
in the non-volatile memory.
See “Description of Error Codes” for
explanation.
©2003 Maytag Appliances Company
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
“Quick Test” Mode for Electronic Range Control
Follow procedure below to use the quick test mode. Entries must be made within 32 seconds of each other or the
control will exit the quick test mode.
1. Press and hold CANCEL and BROIL pads for 3 seconds.
2. Once the control has entered the “Quick Test” mode, release both pads.
3. Press each of the following pads indicated in the table below.
NOTE:
First time one of following pads are pressed it will activate the response.
The second time the pad is pressed it will deactivate the response.
Display will indicate the following:
Pad
Response
BAKE ................................... Bake DLB and Bake relay activated
BROIL.................................. Broil DLB and Broil relay activated
KEEP WARM ...................... Bake DLB and Broil DLB activated
CONVECT BAKE ................ Convection Fan on high speed
CONVECT ROAST ............. Cooling Fan activated
CLEAN ................................ MDL relay activated
COOK & HOLD ................... Displays last diagnostic code
FAVORITE .......................... Displays EEPROM version number
TIMER ................................. Displays main code version number
CLOCK ................................ All display segments illuminated
OVEN LIGHT....................... Oven light activated
CANCEL.............................. Exit Quick Test mode
1........................................... Even segments on
2........................................... Odd segments on
3........................................... Convection Ring activated; Convection Ring DLB activated
4........................................... Bake relay activated
5........................................... Broil relay activated
6........................................... Convection relay activated
7........................................... N/A
8........................................... N/A
9........................................... N/A
AUTOSET ........................... Steps through last 5 diagnostic codes
Description of Error Codes
Error diagnostic codes can only be viewed by entering the Diagnostic Code Display Mode.
Each error code is four digits long and is created based on the following table.
Digit
st
1
nd
2
rd
3
th
4
Description
1 – Local to the control circuit board
3 – Sensor or meat probe
4 – Control input
9 – Door lock
Measurable:
d – Diagnostic: measurable parameter
c – Control related, replace control
Secondary System: Sequential numbering
Oven Cavity:
1 – Upper oven (or single cavity oven)
2 – Lower oven
c – Control specific
Primary System:
Diagnostic Code Display Mode can be activated by pressing and holding the AUTOSET pad for 3 seconds at
power-up. Diagnostic Code Display Mode can only be started while powering up the control.
©2003 Maytag Appliances Company
16022498 Rev. 0
21
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
Diagnostic Code Checking
Code
1c1c
1c2c
1c31
1c32
1c6c
1c7c
1c8c
1d11
1d12
1d21
1d22
3d11
3d12
3d21
3d22
4d11
4d12
4d21
4d31
4d51
4d52
9d11
9d12
9d21
9d22
9d31
9d32
Description
Shorted key
Keyboard tail disconnected
Cancel key circuit problem
Cancel key circuit problem
EEPROM error
Control not calibrated
Cooking program error
Runaway temp (650°F), door unlocked
Runaway temp (650°F), door unlocked
Runaway temp (950°F), door locked
Runaway temp (950°F), door locked
Sensor open
Sensor open
Sensor shorted
Sensor shorted
Door switch position failure
Door switch position failure
No reverse airflow fan rotation (no/low RPM)
Reverse airflow fan state (on when should be off)
Door switch circuit failure
Door switch circuit failure
Latch will not lock
Latch will not lock
Latch will not unlock
Latch will not unlock
Latch state unknown, both locked and unlocked
Latch state unknown, both locked and unlocked
When Checked
Always
Always
Always
Always
When accessing EEPROM
Always
Cook or clean programmed
Latch unlocked
Latch unlocked
Latch locked
Latch locked
Cook or clean active
Cook or clean active
Cook or clean active
Cook or clean active
Clean or keyboard Lockout active
Clean or keyboard Lockout active
Clean or Cook programmed
Suppose to be OFF
Convect, Clean or Keyboard Lockout programmed
Convect, Clean or Keyboard Lockout programmed
Latch should be locked
Latch should be locked
Latch should be unlocked
Latch should be unlocked
Latch should be locked or when lock attempted
Latch should be locked or when lock attempted
Detection
1 minute
1 minute
20 seconds
20 seconds
3 tries
3 tries
3 tries
1 minute
1 minute
1 minute
1 minute
20 seconds
20 seconds
20 seconds
20 seconds
1 minute
1 minute
1 minute
1 minute
1 minute
1 minute
See Note 6
See Note 6
See Note 6
See Note 6
See Note 6
See Note 6
Diagnostic Code Handling
Code
Measurable
What is Displayed
1c1c
Keypress
Nothing
1c2c
Keyboard loop improper value
Nothing
1c31
1c32
1c6c
1c7c
1c8c
1d11
1d12
1d21
1d22
3d11
3d12
3d21
3d22
4d11
4d12
4d21
4d31
4d51
Cancel key improper value
Cancel key improper value
No response from EEPROM
Calibration value out of range
CRC invalid
Sensor resistance > 2237 Ohms
Sensor resistance > 2237 Ohms
Sensor resistance > 2787 Ohms
Sensor resistance > 2787 Ohms
Sensor resistance > Infinite Ohms
Sensor resistance > Infinite Ohms
Sensor resistance > 0 Ohms
Sensor resistance > 0 Ohms
Door switch not closed when door is locked
Door switch not closed when door is locked
No reverse airflow fan rotation (no/low RPM)
Reverse airflow fan state (on when should be off)
Door switch not open or closed
4d52
Door switch not open or closed
9d11
9d12
9d21
9d22
9d31
9d32
Lock switch not closed
Lock switch not closed
Unlock switch not closed
Unlock switch not closed
Latch both locked and unlocked
Latch both locked and unlocked
22
BAKE flashes 3
BAKE flashes 3
Nothing
“CAL” in the time digits
Nothing
BAKE flashes 3
BAKE flashes 3
BAKE flashes 3
BAKE flashes 3
BAKE flashes 3
BAKE flashes 3
BAKE flashes 3
BAKE flashes 3
Nothing
Nothing
Nothing
Nothing
Nothing
Nothing
LOCK flashes 3
LOCK flashes 3
LOCK flashes 3
LOCK flashes 3
LOCK flashes 3
LOCK flashes 3
16022498 Rev. 0
Action Taken By Control
Disables audible for affected key depression
Disables all outputs 1, 2
Disables lights and timers
Disables audible for key depression
Disables all outputs 1
Disables lights and timers
Disables all outputs for cavity 1
Disables all outputs for cavity 1
Disables all outputs 1
Completely disables oven 4
Cancels active cook function
Disables all cook function for cavity
Disables all cook function for cavity
Disables all cook function for cavity
Disables all cook function for cavity
Disables all cook function for cavity
Disables all cook function for cavity
Disables all cook function for cavity
Disables all cook function for cavity
Disables Clean and Lockout functions 5
Disables Clean and Lockout functions 5
Disables all cook function for cavity
No action
Disables Convect, Clean, and Lockout functions 4, 5
Turn off light and disable light from door switch
Disables Convect, Clean, and Lockout functions 4, 5
Turn off light and disable light from door switch
Disables Clean and Lockout functions 4
Disables Clean and Lockout functions 4
Disables Clean and Lockout functions 4
Disables Clean and Lockout functions 4
Disables Clean and Lockout functions 4
Disables Clean and Lockout functions 4
©2003 Maytag Appliances Company
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
NOTES:
1
2
3
4
5
6
“Action Taken” applies as long as the condition exists. If the condition goes away, the control recovers.
If there is a cook function or timer active, the function continues. The user cannot edit the function, and [Cancel] will cancel the cook
mode.
Flash rate: 0.2 seconds on, 0.1 second off. Pressing any key will clear the display until the fault clears and is re-triggered.
“Action Taken” applies until there is a POR (Power On Reset [“hard reset”]).
If the control believes the door is locked, it will attempt to unlock it when the function cancels and the cavity temperature cools.
Special conditions for latch faults (9dxx):
•
A known good unlock position is defined as when the unlock switch reads closed and lock switch reads open.
•
A known good lock position is defined as when the unlock switch reads open and lock switch reads closed.
•
A faulted switch means the switch input is reading an invalid state, neither open nor closed.
•
Once a latch fault occurs, latch movement is disabled until there is a POR. An error tone will sound if a function requiring a
faulted latch is attempted.
•
If at POR, the latch is not at a known good unlock position:
•
If the latch is at a good lock position, it will attempt to unlock when the RTD (Resistance Temperature Device)
temperature is below 400°F.
•
If the latch is not at a good lock position, the control will fault.
•
If a latch fault occurs while the RTD is above the lock temperature, the latch will not try to move, but the fault is still logged
to EEPROM after the first stage of detection.
•
The Display column for latch faults applies 1) If the latch was moving when the fault occurred; 2) If the latch is already in a
known locked state when the fault occurs.
•
LOCK flashes after a fault is detected and until the unlocked position is achieved. The unlock position may be
identified by a successful unlock switch closure, or as the result of timing when the unlock switch is not
functioning properly.
•
If the last known good position was unlock (e.g. baking, or idle) and a latch fault occurs, the motor is never moved. The
fault is logged to EEPROM and is not seen by the user.
•
The detection for latch faults is in two stages. The first stage is to let the control recover without moving the latch. After
this:
•
If the latch was previously at a known good unlock position, the latch will not move and the control will fault.
•
If the control was previously in a known good lock position:
•
•
If the RTD is below 400°F, the latch will attempt to recover to it’s proper position (up to three
revolutions). If it cannot, the control will fault and the latch will move to a calculated unlock position.
•
If the RTD is at or above 400°F, the control will fault. When the RTD cools to below 400°F, the control
will attempt to recover to a good unlock position (up to three revolution). If it cannot, the control will fault
and the latch will move to a calculated unlock position.
•
Note: If the unlock position cannot be found, this may result in a second fault, the first fault occurring
when the latch request was locked, and the second when the latch request is unlocked.
If the latch is moving when the fault occurs, the control will bypass the first stage of detection and immediately try
to find it’s proper position. If it cannot, the control will fault and the latch will move to a calculated unlock position.
•
Affected DLBs (Double Line Breaks) and loads are disabled during detection.
•
If the control is in a known good unlock position and the lock switch becomes faulted:
•
•
The control will not fault.
•
If a function requiring latch movement is attempted while the lock switch is faulted, the control will sound an error
tone and the function will be disabled.
If the control is in a known good lock position and the unlock switch becomes faulted:
•
The control will not fault.
•
After the function is canceled and unlock is attempted, the control will attempt to unlock the latch according to the
procedures in these notes.
©2003 Maytag Appliances Company
16022498 Rev. 0
23
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
Illustration
M1 Controlled
Component
Oven temperature
adjustment
M1 Controlled
Temperature display
M1 Controlled
Clock Display
M1 Controlled
24 Hour Clock
M1 Controlled
Factory Default
M1 Controlled
Twelve hour off
M1 Controlled
Sabbath Mode
Test Procedure
Press BAKE pad.
Enter 550 on the digit-pad.
Immediately press and hold BAKE
pad for 3 seconds.
Oven can be adjusted from -35 to +35
degrees in 5-degree increments by
pressing AUTOSET pad. To avoid
over adjusting the oven, move
temperature 5 degrees each time.
Wait 4 seconds for the data entry timer
to expire to accept the change.
Temperature adjustment will be
retained even through a power failure.
Press and hold Cancel and Bake
pads for 3 seconds.
Press and hold Cancel and Clock
pads for 3 seconds.
Press and hold Cancel and Delay
pads for 3 seconds.
Press and hold Cancel and Keep
Warm pads for 3 seconds.
Control will automatically cancel any
cooking operation and remove all
relay drives 12 hours after the last pad
touch.
Hold CLOCK pad for 3 seconds to
activate Sabbath mode.
Hold CLOCK pad for 3 seconds to
disable Sabbath mode.
M1 Controlled
M1 Controlled
Child lock out
Diagnostic Code
Display
Press and hold Cancel and Cook &
Hold pads for 3 seconds. “OFF” will
display where the temperature
normally appears. “LOCK” will display
flashing while door is locking.
To reactivate the control, press and
hold Cancel and Cook & Hold pads
for 3 seconds.
Press and hold Up Arrow pad and
Power Up the unit.
Cycle through the codes using the
number pads 1 through 5.
24
16022498 Rev. 0
Results
While increasing or decreasing oven
temperature, this does not affect selfcleaning temperature.
This mode enables the user to indicate
°F or °C on the display.
Allows clock to be toggled On or OFF.
Allows the time on the clock to be
toggled from 12 hour or 24 hour display.
Allows the clock to be reset to factory
settings.
See Sabbath mode to disable.
“SAb” will be displayed and flash for 5
seconds.
Display will go back to time of day.
All pad inputs are disabled except for
CANCEL and CLOCK pads.
This mode disables the normal 12 hour
shutoff to allow operation of the bake
mode for a maximum of 72 hours.
This is a safety feature that can be used
to prevent children from accidentally
programming the oven. It disables the
electronic oven control.
Child lockout features must be reset after
a power failure.
The last 5 diagnostic codes will be stored
in the non-volatile memory.
See “Description of Error Codes” for
explanation.
©2003 Maytag Appliances Company
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
Illustration
M2 Controlled
Component
Oven temperature
adjustment
M2 Controlled
Temperature display
M2 Controlled
Clock Display
M2 Controlled
24 Hour Clock
M2 Controlled
Factory Default
M2 Controlled
Twelve hour off
M2 Controlled
Sabbath Mode
Test Procedure
Press BAKE pad.
Enter 550 on the digit-pad.
Immediately press and hold BAKE
pad for 3 seconds.
Oven can be adjusted from -35 to +35
degrees in 5-degree increments by
pressing AUTOSET pad. To avoid
over adjusting the oven, move
temperature 5 degrees each time.
Wait 4 seconds for the data entry timer
to expire to accept the change.
Temperature adjustment will be
retained even through a power failure.
Press and hold Cancel and Bake
pads for 3 seconds.
Press and hold Cancel and Clock
pads for 3 seconds.
Press and hold Cancel and Favorite
pads for 3 seconds.
Press and hold Cancel and Keep
Warm pads for 3 seconds.
Control will automatically cancel any
cooking operation and remove all
relay drives 12 hours after the last pad
touch.
Hold CLOCK pad for 3 seconds to
activate Sabbath mode.
Hold CLOCK pad for 3 seconds to
disable Sabbath mode.
M2 Controlled
M2 Controlled
Child lock out
Diagnostic Code
Display
Press and hold Cancel and Cook &
Hold pads for 3 seconds. “OFF” will
display where the temperature
normally appears. “LOCK” will display
flashing while door is locking.
To reactivate the control, press and
hold Cancel and Cook & Hold pads
for 3 seconds.
Press and hold Up Arrow pad and
Power Up the unit.
Cycle through the codes using the
number pads 1 through 5.
©2003 Maytag Appliances Company
16022498 Rev. 0
Results
While increasing or decreasing oven
temperature, this does not affect selfcleaning temperature.
This mode enables the user to indicate
°F or °C on the display.
Allows clock to be toggled On or OFF.
Allows the time on the clock to be
toggled from 12 hour or 24 hour display.
Allows the clock to be reset to factory
settings.
See Sabbath mode to disable.
“SAb” will be displayed and flash for 5
seconds.
Display will go back to time of day.
All pad inputs are disabled except for
CANCEL and CLOCK pads.
This mode disables the normal 12 hour
shutoff to allow operation of the bake
mode for a maximum of 72 hours.
This is a safety feature that can be used
to prevent children from accidentally
programming the oven. It disables the
electronic oven control.
Child lockout features must be reset after
a power failure.
The last 5 diagnostic codes will be stored
in the non-volatile memory.
See “Description of Error Codes” for
explanation.
25
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
“Quick Test” Mode for Electronic Range Control
Follow procedure below to use the quick test mode. Entries must be made within 32 seconds of each other or the
control will exit the quick test mode.
1. Press and hold CANCEL and BROIL pads for 3 seconds.
2. Once the control has entered the “Quick Test” mode, release both pads.
3. Press each of the following pads indicated in the table below.
NOTE:
First time one of following pads are pressed it will activate the response.
The second time the pad is pressed it will deactivate the response.
NOTE:
This mode can only be entered within the first 5 minutes after power up.
NOTE:
If the temperature sensor is greater than 400°F and the Quick Test mode will be disabled if the
temperature sensor reaches 400°F while under test.
Display will indicate the following:
Key
[Bake]
[Broil]
[Keep Warm]
[Cook&Hold]
[Clean]
[Delay] (M1)
[Favorite] (M2)
[Timer]
[Clock]
[More +]
[Less –]
[Cancel]
Operation
Bake relay activated, DLB relay activated
Broil relay activated, DLB relay activated
DLB relay activated
Last Diagnostic Code displayed
MDL relay activated (lock and unlock)
EEPROM Version Number displayed
EEPROM Version Number displayed
Main Code Version Number displayed
All Segments On
Even Segments On
Odd Segments On
End Factory Test Mode
Description of Error Codes
Error diagnostic codes can only be viewed by entering the Diagnostic Code Display Mode.
Each error code is four digits long and is created based on the following table.
Digit
st
1
nd
2
rd
3
th
4
Description
1 – Local to the control circuit board
3 – Sensor or meat probe
4 – Control input
9 – Door lock
Measurable:
d – Diagnostic: measurable parameter
c – Control related, replace control
Secondary System: Sequential numbering
Oven Cavity:
1 – Upper oven (or single cavity oven)
2 – Lower oven
c – Control specific
Primary System:
Diagnostic Code Display Mode can be activated by pressing and holding the AUTOSET pad for 3 seconds at
power-up. Diagnostic Code Display Mode can only be started while powering up the control.
26
16022498 Rev. 0
©2003 Maytag Appliances Company
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
Diagnostic Code Checking
Code
1c1c
1c2c
1c31
1c6c
1c7c
1c8c
1d11
1d21
3d11
3d21
4d11
Description
Shorted key
Keyboard tail disconnected
Cancel key circuit problem
EEPROM error
Control not calibrated
Cooking program error
Runaway temp (650°F), door unlocked
Runaway temp (950°F), door locked
Sensor open
Sensor shorted
Door switch position failure
4d51
Door switch circuit failure
9d11
9d21
9d31
Latch will not lock
Latch will not unlock
Latch state unknown, both locked and unlocked
When Checked
Always
Always
Always
When accessing EEPROM
Always
Cook or clean programmed
Latch unlocked
Latch locked
Cook or clean active
Cook or clean active
Clean or keyboard Lockout
active
Convect, Clean or Keyboard
Lockout programmed
Latch should be locked
Latch should be unlocked
Latch should be locked or when
lock attempted
Detection
1 minute
1 minute
20 seconds
3 tries
3 tries
3 tries
1 minute
1 minute
20 seconds
20 seconds
1 minute
1 minute
See Note 6
See Note 6
See Note 6
Diagnostic Code Handling
Code
Measurable
What is Displayed
1c1c
Keypress
Nothing
1c2c
Keyboard loop improper value
Nothing
1c31
1c6c
1c7c
1c8c
1d11
1d21
3d11
3d21
4d11
Cancel key improper value
No response from EEPROM
Calibration value out of range
CRC invalid
Sensor resistance > 2237 Ohms
Sensor resistance > 2787 Ohms
Sensor resistance > Infinite Ohms
Sensor resistance > 0 Ohms
Door switch not closed when door is
locked
Door switch not open or closed
4d51
3
BAKE flashes
Nothing
“CAL” in the time digits
Nothing
3
BAKE flashes
3
BAKE flashes
3
BAKE flashes
3
BAKE flashes
Nothing
Nothing
9d11
Lock switch not closed
9d21
Unlock switch not closed
9d31
Lock and unlock switches both closed
©2003 Maytag Appliances Company
LOCK flashes
3
LOCK flashes
3
LOCK flashes
3
16022498 Rev. 0
Action Taken By Control
Disables audible for affected key
depression
1, 2
Disables all outputs
Disables lights and timers
Disables audible for key depression
1
Disables all outputs
Disables lights and timers
1
Disables all outputs for cavity
1
Disables all outputs
4
Completely disables oven
Cancels active cook function
Disables all cook function for cavity
Disables all cook function for cavity
Disables all cook function for cavity
Disables all cook function for cavity
Disables Clean and Lockout
5
functions
Disables Convect, Clean, and
4, 5
Lockout functions
Turn off light and disable light from
door switch
Disables Clean and Lockout
4
functions
Disables Clean and Lockout
4
functions
Disables Clean and Lockout
4
functions
27
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
NOTES:
1
2
3
4
5
6
“Action Taken” applies as long as the condition exists. If the condition goes away, the control recovers.
If there is a cook function or timer active, the function continues. The user cannot edit the function, and [Cancel] will cancel the cook
mode.
Flash rate: 0.2 seconds on, 0.1 second off. Pressing any key will clear the display until the fault clears and is re-triggered.
“Action Taken” applies until there is a POR (Power On Reset [“hard reset”]).
If the control believes the door is locked, it will attempt to unlock it when the function cancels and the cavity temperature cools.
Special conditions for latch faults (9dxx):
•
A known good unlock position is defined as when the unlock switch reads closed and lock switch reads open.
•
A known good lock position is defined as when the unlock switch reads open and lock switch reads closed.
•
A faulted switch means the switch input is reading an invalid state, neither open nor closed.
•
Once a latch fault occurs, latch movement is disabled until there is a POR. An error tone will sound if a function requiring a
faulted latch is attempted.
•
If at POR, the latch is not at a known good unlock position:
•
If the latch is at a good lock position, it will attempt to unlock when the RTD (Resistance Temperature Device)
temperature is below 400°F.
•
If the latch is not at a good lock position, the control will fault.
•
If a latch fault occurs while the RTD is above the lock temperature, the latch will not try to move, but the fault is still logged
to EEPROM after the first stage of detection.
•
The Display column for latch faults applies 1) If the latch was moving when the fault occurred; 2) If the latch is already in a
known locked state when the fault occurs.
•
•
If the last known good position was unlock (e.g. baking, or idle) and a latch fault occurs, the motor is never moved. The
fault is logged to EEPROM and is not seen by the user.
•
The detection for latch faults is in two stages. The first stage is to let the control recover without moving the latch. After
this:
•
If the latch was previously at a known good unlock position, the latch will not move and the control will fault.
•
If the control was previously in a known good lock position:
•
•
If the RTD is below 400°F, the latch will attempt to recover to it’s proper position (up to three
revolutions). If it cannot, the control will fault and the latch will move to a calculated unlock position.
•
If the RTD is at or above 400°F, the control will fault. When the RTD cools to below 400°F, the control
will attempt to recover to a good unlock position (up to three revolutions). If it cannot, the control will
fault and the latch will move to a calculated unlock position.
•
Note: If the unlock position cannot be found, this may result in a second fault, the first fault occurring
when the latch request was locked, and the second when the latch request is unlocked.
If the latch is moving when the fault occurs, the control will bypass the first stage of detection and immediately try
to find it’s proper position. If it cannot, the control will fault and the latch will move to a calculated unlock position.
•
Affected DLBs (Double Line Breaks) and loads are disabled during detection.
•
If the control is in a known good unlock position and the lock switch becomes faulted:
•
28
LOCK flashes after a fault is detected and until the unlocked position is achieved. The unlock position may be
identified by a successful unlock switch closure, or as the result of timing when the unlock switch is not
functioning properly.
•
The control will not fault.
•
If a function requiring latch movement is attempted while the lock switch is faulted, the control will sound an error
tone and the function will be disabled.
If the control is in a known good lock position and the unlock switch becomes faulted:
•
The control will not fault.
•
After the function is canceled and unlock is attempted, the control will attempt to unlock the latch according to the
procedures in these notes.
16022498 Rev. 0
©2003 Maytag Appliances Company
Disassembly Procedures
!
To avoid risk of electrical shock, personal injury, or death:
disconnect electrical and gas supply before servicing.
WARNING
Removing and Replacing Range
Control Board Assembly
1.
2.
3.
4.
5.
1. Remove control panel, see “Control Panel”
procedure, steps 1 through 6.
2. Remove screws securing control board bracket to
control panel.
3. Label and disconnect terminal plug from control
board assembly.
4. Reverse procedure to reinstall control board
assembly.
Turn off power to the range at the circuit breaker.
Turn off gas supply line to unit.
Pull the range forward out of the cabinet opening.
Unplug the power cord leading from unit to outlet.
Replace the range using the installation instructions
and anti-tip bracket(s).
Front Control Panel
1. Open or remove oven door from unit.
2. Remove control knobs from gas valves, by pulling.
3. Remove screws securing front control panel, located
on the bottom edge of the front control panel.
4. Remove control panel by sliding one way or the other
and pulling away from the unit.
5. Reverse procedure to reassemble.
Maintop Assembly
1. Turn power off to unit.
2. Remove front control panel, see "Front Control Panel"
procedure.
3. Remove grates and caps.
4. Remove screws securing top surface burner to
maintop.
5. Lift surface burner off.
6. Raise the front edge of the maintop and pull forward.
7. Lift maintop assembly from the oven chassis.
8. Reverse procedure to reinstall maintop assembly.
Control Panel
1. Remove maintop assembly, see "Maintop Assembly"
procedure, steps 1 through 7.
2. Remove screws securing control panel heat shield.
3. Remove screws securing bottom outside edges of the
control panel.
4. Pull unit out from the wall far enough to allow the
back outside screws to be loosened.
5. Loosen the back outside screws securing control
panel to backguard.
6. Grasp front lower outside edges of the control panel
and push inward on the outside edges of the
backguard to release the control panel front.
Rocker Switch
1. Remove control panel, see "Control Panel" procedure
for removal.
2. Disconnect and label wire terminals from rocker
switch.
3. Squeeze tabs on rocker switch and push outward to
release from control panel.
4 . Reverse procedure to reinstall indicator light.
Top Surface Valve and Spark Switch
1. Remove control panel, see “Front Control Panel
Removal” procedure.
2. Remove spark switch by pulling straight off valve.
3. Remove screw securing valve to front manifold.
4. Replace and reassemble in reverse order.
Top of Surface Burner
1.
2.
3.
4.
Turn off electrical power and gas to the range.
Disconnect gas and power from unit.
Remove grates and caps.
Remove screws securing top surface burner to
maintop.
5. Lift surface burner off.
6. Replace and reassemble in reverse order.
Bottom of Surface Burner
1. Remove maintop assembly, see "Maintop Assembly"
procedure, steps 1 through 7.
2. Remove nut securing burner tubing to surface valve.
3. Replace and reassemble in reverse order.
NOTE: Front edges of the control panel are difficult to
release from backguard.
7. Once the control panel bottom edges are free, pull
control panel forward and raise the control panel
upward to release screws securing top back edges
and allow control panel to tip forward.
8. Reverse procedure to reinstall control panel.
©2003 Maytag Appliances Company
16022498 Rev. 0
29
Disassembly Procedures
!
To avoid risk of electrical shock, personal injury, or death:
disconnect electrical and gas supply before servicing.
WARNING
Oven Sensor
Broil Burner and Ignitor
1. Disconnect power before servicing.
2. Open oven door and remove screws securing sensor
to oven cavity.
1.
2.
3.
4.
NOTE: Gently pull wiring through cavity wall.
3. Disconnect oven sensor at the connector terminal
and remove.
4. Reverse procedure to reinstall sensor.
NOTE: Verify connection is pushed through the
insulation.
Turn off electrical power and gas to the range.
Disconnect gas and power from unit.
Remove oven door, and racks.
Remove screws securing ignitor wire plate cover to
back of the oven cavity.
5. Maneuver ignitor wire terminal plug through the rear
of the oven cavity.
6. Disconnect ignitor wire terminal plug.
7. Remove screws securing broiler to oven cavity.
8. Carefully maneuver burner off of the broiler orifice
spud and remove from cavity.
9. Remove screws securing ignitor to broiler.
10.Remove wing nut securing flame spreader to broiler.
11. Replace and reassemble in reverse order.
Valve / Regulator Assembly
NOTE: Requires removal of range from installation
position.
Convection Fan Assembly
1. Turn off power to unit.
2. Open oven door or remove oven door, see “Door
Removal”.
3. Remove screws securing convection fan cover to
convection fan assembly.
4. Remove screws securing convection fan assembly to
rear of oven cavity.
5. Slide convection fan assembly down and tilt forward
on the top portion to allow assembly to pass through
rear oven cavity.
6. Disconnect and label wires from convection fan
motor.
7. Reverse procedure to reinstall convection fan
assembly.
Bake Burner and Ignitor
1.
2.
3.
4.
5.
Turn off electrical power and gas to the range.
Disconnect gas and power from unit.
Remove oven door and racks.
Remove screws securing bottom bake cover.
Raise the back of the bake burner cover and slide
cover back to release the front edge of cover and lift
out of oven cavity.
6. Remove screws securing bake burner assembly to
the oven chassis.
7. Maneuver bake burner from the burner orifice and out
of the slotted location.
8. Pull forward on assembly to allow the ignitor terminal
plug to pass through the back of the oven cavity.
9. Disconnect terminal plug and remove assembly from
the oven cavity.
10.Remove screws securing ignitor to bake burner.
11. Replace and reassemble in reverse order.
30
1.
2.
3.
4.
5.
6.
7.
Turn off electrical power and gas to the range.
Disconnect gas and power from unit.
Remove nut securing broiler tubing to gas valve.
Remove nut securing bake tuning to gas valve.
Remove screws securing assembly to unit chassis.
Disconnect wires and gas lines to gas valve.
Replace and reassemble in reverse order.
Automatic Oven Door Latch Assembly
NOTE: Requires removal of range from installation
position.
1. Remove maintop assembly, see "Maintop Assembly"
procedure, steps 1 through 7.
2. Remove screws securing latch assembly to the front
of the oven cavity outer shell.
3. Disconnect and label wire terminals from latch
assembly.
4. Remove screws securing upper rear access panel to
the back of the unit.
5. Remove screws securing latch assembly to the back
of the unit chassis.
6. Reverse procedure to reinstall door latch assembly.
Spark Module
NOTE: Requires removal of range from installation
position.
1. Remove screws securing lower rear access panel.
2. Disconnect and label wire connections from the spark
module.
3. Remove screws securing spark module to unit
chassis.
4. Replace and reverse procedure to reassemble.
16022498 Rev. 0
©2003 Maytag Appliances Company
Disassembly Procedures
!
To avoid risk of electrical shock, personal injury, or death:
disconnect electrical and gas supply before servicing.
WARNING
Door Plunger Light Switch
Backguard
1. Remove maintop assembly, see "Maintop Assembly"
procedure, steps 1 through 7.
2. Label and disconnect wire terminals from switch.
3. Slide metal sleeve forward and flex wire the release
from door plunger light switch.
4. Squeeze metal tab and push switch inward to
remove.
5. Reverse procedure to reinstall door plunger light
switch.
NOTE: Requires removal of range from installation
position.
NOTE: Be sure to install door plunger light switch heat
shield on new switch when replacing switch.
Storage Drawer and Storage Drawer Panel
Removal
1. Pull drawer straight out to first stop. Lift front and pull
out to second stop.
2. Let front of door rest on floor. Place hands toward
back of drawer and lift it out.
Oven Door Removal
!
1. Remove maintop assembly, see "Maintop Assembly"
procedure, steps 1 through 7.
2. Remove screws securing upper back panel form unit.
3. Remove screws securing bottom outside edges of the
backguard to unit chassis.
4. Reverse procedure to reinstall backguard.
WARNING
To avoid risk of personal injury or property damage,
do not lift oven door by the handle.
1. Open oven door and place door hinge locking device
into lock position.
2. Place oven door in first stop position, then grasp both
sides and lift up off the hinges.
3. Reverse procedure to reinstall oven door.
Oven Door Hinge Receptacle
1. Turn off power to unit.
2. Remove oven door, see "Oven Door Removal"
procedure.
3. Remove maintop assembly, see "Maintop Assembly"
procedure, steps 1 through 4.
4. Remove side panel, see "Side Panel Removal"
procedures.
5. Remove the top and bottom screws securing hinge
assembly to the front frame.
6. Remove hinge from oven chassis.
7. Reverse procedure to reinstall oven door hinge.
Side Panel Removal
1. Turn off power to unit.
2. Remove oven door, see "Oven Door Removal"
procedure.
3. Remove maintop assembly, see "Maintop Assembly"
procedure, steps 1 through 4.
4. Remove screws securing lower rear galvanized cover
from unit.
5. Remove screws securing top and back of side panel.
6. Pull rear of side panel away from range then slide
side panel forward to release from side panel
spacers.
7. Reverse procedure to reinstall side panel.
©2003 Maytag Appliances Company
3. To replace:
a. Place the set of rollers on the drawer behind the
set of rollers on the oven.
b. Align the guides and push the drawer back into
position.
16022498 Rev. 0
31
Disassembly Procedures
!
To avoid risk of electrical shock, personal injury, or death:
disconnect electrical and gas supply before servicing.
WARNING
Storage Drawer Track Removal
Frameless Door Disassembly
1. Remove the storage drawer by pulling it out to the
fully open or stop position, lifting the drawer at the
rear to disengage the drawer track rollers from the
drawer runners, and sliding the drawer out of the
range.
2. The tracks are mounted to a rear support and the
frame of the range. Remove the two track mounting
screws and remove the track. If the track support is
being replaced, remove the mounting screw securing
it to the side frame and remove the support.
1. Remove oven door, see "Oven Door Removal"
procedure.
2. Place door on a protected surface.
3. Slide outer oven door glass and trim towards the
bottom of the oven door and remove.
4. Detach right and left trim pieces for outer door glass.
Oven Light Assembly
NOTE: Proceed with the following steps for door handle
and inner door disassembly.
Oven Light Bulb/Oven Light Socket
NOTE: Requires removal of unit from cabinet to replace
oven light socket.
1.
2.
3.
4.
Turn off power to unit.
Open oven door to gain access to oven light.
Unscrew (counterclockwise) glass knurled dome.
Unscrew (counterclockwise) oven light bulb.
NOTE: To avoid damaging the new bulb and
decreasing life of the bulb, do not touch new
bulb with bare hands or fingers.
Hold with a cloth or paper towel.
NOTE: Proceed with the following steps for oven light
socket removal.
5. Remove unit from installation position, see
“Removing and Replacing Oven” procedure.
6. Disconnect or unplug the power cord leading from
unit to fuse box or junction box depending on unit.
7. Remove screws securing back cover and remove.
8. Carefully displace fiberglass insulation away from
rear of light socket.
9. Disconnect wires from light socket.
10.Push socket assembly inwards into the oven cavity.
11. Reverse procedure to reinstall light socket.
Reposition insulation around lamp socket.
NOTE: Reposition fiberglass insulation around oven
light socket to eliminate possibility of heat
related problems.
32
NOTE: Proceed with the following steps for door hinge,
door handle, and inner door disassembly.
5. Remove screws securing door hinge to oven door
chassis.
6. Remove screws securing top door handle trim to
oven door chassis.
7. Remove screws securing door handle brackets to
inner door panel.
8. Lift upward on the lower side of the door handle to
release side alignment screws and rotate towards the
top of the oven door to release and remove.
9. Remove screws securing door handle to door handle
brackets.
NOTE: Proceed with the following steps for inner door
disassembly.
10.Remove screws securing lower door glass retainer to
door baffle and remove.
11. Slide inner door glass downward to release from
upper door glass retainers and remove.
12.Remove screws securing door baffle to door lining
and remove.
13.Remove insulation from oven door.
14.Lift inner glass and glass frame from oven door.
15.Reverse procedure to reassemble oven door.
Power Cord
NOTE: Requires removal of range from installation
position.
1.
2.
3.
4.
Turn off electrical power and gas to the range.
Disconnect gas and power cord from unit.
Remove storage drawer.
Disconnect power cord plug located behind storage
drawer.
5. Remove screw securing cord to unit.
6. Replace and reassemble in reverse order.
16022498 Rev. 0
©2003 Maytag Appliances Company
Disassembly Procedures
!
To avoid risk of electrical shock, personal injury, or death:
disconnect electrical and gas supply before servicing.
WARNING
Frameless Oven Door
Glass
frame
Door
baffle
Inner
door
glass
Side
trim
Door
linning
Inner
glass
Door
hinge
Top
trim
Insulation
Door
glass
retainer
Door
handle
Bottom
trim
©2003 Maytag Appliances Company
Tape
Door
handle
bracket
Side
trim
Door
glass
16022498 Rev. 0
33
Appendix A
©2003 Maytag Appliances Company
16022498
A–1
Gas Conversion
*DV &RQYHUVLRQ
d‚‹‚~‰
This range is equipped with fixed orifices on all burners
and a convertible appliance pressure regulator. The unit
serial plate states which gas it was adjusted for at the
factory. To convert the unit to either Natural gas or LP gas
will require replacing the oven orifice hoods, replacement
of top burner orifices, conversion of the appliance
pressure regulator and adjustment of air shutters on both
oven burners.
2. Unscrew the hex shaped conversion cap from the neck
of the regulator. (A wrench may be required to loosen
the cap). See figure 2.
Gas inlet pressure to the appliance pressure regulator
should be as follows for both operation and checking of
appliance pressure regulator setting:
fkibq mobpprob fk
fk`ebp lc t^qbo `lirjk
Minimum
Maximum
k^qro^i
d^p
5
14
im
d^p
11
14
1$785$/ *$6 6(77,1*
´1µ ,6 6+2:1
7851 ,1 &2817(5&/2&.:,6(
',5(&7,21 72 5(029(
),*85( 3. Invert the cap and screw it back into place. See figure
3.
^‰†~‹€‚ m‚’‚ o‚„’‰~‘Œ `Œ‹“‚†Œ‹
The unit appliance pressure regulator must be set to
match the type gas supply used. If converting from
Natural gas to LP gas, the appliance pressure regulator
must be converted to regulate LP gas. If converting from
LP gas to Natural gas, the appliance pressure regulator
must be converted to regulate Natural gas. The regulator
is located at the bottom of the back of the range.
/3 *$6
6(77,1*
´/3µ ,6 6+2:1
Follow the instructions below to convert the regulator for
use with LP gas. (This appliance is shipped from the
factory adjusted for use with Natural gas.)
),*85( 1. Remove plastic cover from pressure regulator neck.
See figure 1.
*$6 35(6685( 5(*8/$725
/2&$7(' $7 %27720 2) 7+( 5($5 2) 7+( 5$1*(
3/$67,& &29(5
),*85( 4. Screw the cap securely back into place in the neck of
the pressure regulator. (The cap need not be wrenchtightened upon replacement. Firm finger tightening will
secure the cap). Replace plastic cover over cap. See
figure 4.
7851 &/2&.:,6(
72 ,167$//
),*85( UNMNmRVUJSM
(07-03-00)
A–2
16022498
©2003 Maytag Appliances Company
Gas Conversion
6XUIDFH %XUQHUV 7R /33URSDQH *DV
`^rqflkW This cooktop is not removable. Do not attempt
to remove this cooktop. Save the natural gas orifices
removed from the appliance for possible future conversion
to natural gas.
cŒ ^‰‰ _’‹‚ iŒ€~‘†Œ‹W
klqbW Surface burner orifices are located in LP
conversion kit plastic bag attached to the back of the
range.
a. Remove the top grates and burner caps.
b. Remove each burner head by removing two screws.
(See figure 1) klqbW Convert one burner at a time to
avoid incorrect installation.
c. fjmloq^kqW Replace these two screws after
removing burner head. The screws will secure orifice
holder and prevent damage to electrode or tubing while
changing orifice.
d. Remove the factory installed natural gas orifices from
the center of the orifice holders using a 7mm nut driver.
(See figure 1). Remember to keep the original natural
gas orifices for possible later conversion to natural gas.
e. Replace the orifice in each of the four or five orifice
holders with the correct LP/Propane gas orifice (see
figure 2).
cfdrob N
klqbW See figure 3 for natural gas orifice size and
information.
fjmloq^kqW Make sure orifice is secured in nut driver
before attempting to install orifice.
TIP: Insert tape into the head of the 7mm nut driver to
help prevent the orifice from falling into the range.
Tighten each orifice until snug. Use caution not to over
tighten.
f. When orifice change is complete, remove two screws
then re-install burner head and secure with same two
screws.
g. Replace the burner caps and grates using caution
when replacing each burner cap so that electrode is not
damaged.
2
©2003 Maytag Appliances Company
16022498
A–3
im d^p proc^`b _rokbo lofcf`b `lkcfdro^qflk
Gas Conversion
3
A–4
16022498
©2003 Maytag Appliances Company
©2003 Maytag Appliances Company
EpfwbF
cfdrob P
k^qro^i d^p proc^`b _rokbo lofcf`b `lkcfdro^qflk
Gas Conversion
16022498
4
A–5
Gas Conversion
&RQYHUWLQJ %DNH %XUQHU 2ULILFH
qŒ `Œ‹“‚‘ _~ˆ‚ _’‹‚ l†ƒ†€‚W
REMOVE SCREW
1. Remove ALL oven racks.
2. Remove two screws in rear of oven
which hold oven bottom in place. See
figure 1.
3. Remove oven bottom by raising rear
of part so that front edge clears front
flange on front frame. Then lift oven
bottom straight up - then forward to
remove. See figure 2.
4. Remove oven burner by removing one
screw in front of burner and two
screws at rear next to ignitor. Raise
rear part of burner up till it clears the
opening in the bake chamber, then
gently lay the burner to the right side
in the bake chamber. It is not
necessary to unplug or remove the
ignitor from the burner. See figure 3.
cfdrob N
OVEN BOTTOM MUST CLEAR THIS
EDGE IN ORDER TO BE REMOVED
OPENING IN
BAKE CHAMBER
SCREW
cfdrob O
cfdrob P
5
A–6
16022498
©2003 Maytag Appliances Company
Gas Conversion
5. Insert 1/2² deep-well socket with extension through the
opening in the bake chamber from which the burner
was removed. Insert tool at a downward angle to the
left till it seats over the hex on the bake orifice.
7. Install LP orifice in same 1/2² socket and attach to bake
burner valve by repeating procedure noted in step #5
above. Turn socket clockwise until resistance is felt,
then another 1/4 turn to fully tighten.
Turn socket counter-clockwise until orifice is loose,
remove orifice and tool through opening in bake
chamber.
8. Before re-installing oven bottom, refer to the section
titled “Range Adjustments” in the unit installation
manual for proper air shutter adjustment on bake
burner.
klqbW The bake orifice can also be viewed under the
range by raising the oven door and removing the
storage drawer. See figure 4.
9. Reverse steps 1 - 4 above to complete the conversion.
6. Locate LP bake burner orifice in LP conversion kit
plastic bag mounted at rear of range. Orifice will be
marked “.049”.
fjmloq^kqW Be sure end of burner is engaged over
burner orifice.
BAKE ORIFICE
LP BAKE ORIFICE IS
LOCATED IN THE LP
CONVERSION KIT AND
IS STAMPED WITH
NUMBERS “.049”.
VIEWING THE BAKE ORIFICE AFTER
THE REMOVAL OF THE STORAGE DRAWER
cfdrob Q
6
©2003 Maytag Appliances Company
16022498
A–7
Gas Conversion
&RQYHUWLQJ %URLO %XUQHU 2ULILFH
qŒ `Œ‹“‚‘ _Œ†‰ _’‹‚ l†ƒ†€‚W
1. Remove ALL oven racks.
6. Reverse step #2 above to re-install broil burner to
complete the conversion.
2. Remove one screw in front of broil burner, then gently
position broil burner assembly against rear wall of oven
cavity. This will expose the broil orifice. See figures 1
and 2.
fjmloq^kqW Be sure end of burner is engaged over
burner orifice.
klqbW Pin attached at radius of bend on burner must
be inserted in embossed hole in top rear wall of oven
cavity.
3. Using 1/2² socket, remove broil orifice by turning
counter-clockwise till orifice is loose from brass fitting.
See figure 2.
4. Locate LP broil burner orifice in LP conversion kit
plastic bag mounted at rear of range. Orifice will be
marked “#57” and colored green.
_Œ†‰ _’‹‚ ^† p…’‘‘‚ ^‡’‘Š‚‹‘
5. Repeat step #3 above to install broil orifice. Turn
socket clockwise until resistance is felt, then another
1/4 turn to fully tighten.
Refer to section titled “Range Adjustments” in installation
manual for proper air shutter adjustment after orifice broil
is changed.
cfdrob N
BROIL ORIFICE
TURN COUNTER CLOCKWISE
TO REMOVE. LP BROIL ORIFICE IS
LOCATED IN THE LP CONVERSION
KIT AND HAS #57 AND GREEN
INDICATOR MARK ON ITS SIDE.
cfdrob O
7
A–8
16022498
©2003 Maytag Appliances Company
Gas Conversion
,03257$17
/RZ )ORZ &RQYHUVLRQ )RU 6XUIDFH %XUQHU 9DOYHV
Complete pressure regulator and orifice conversion before
making valve low flow adjustment.
3. Using pliers, gently hold the valve stem in the low
position. See figure 2.
To convert the surface burner valve from Natural to LP
Gas, the minimum flow MUST be adjusted.
4. Insert a slender, thin-blade screwdriver into the recess
at center of valve stem and engage blade with slot in
adjusting screw.
1. Be sure valve is turned to the “LOW” position as shown
on the knob _bclob making adjustments. See figure
1. Otherwise, the valve could be damaged.
5. Turn center stem adjusting screw to set flame size.
This should require about 1/4 turn, more or less.
6. Replace control knob when adjustment is completed.
2. Remove the knob.
Proper adjustment will produce a stable, steady blue
flame of minimum size. The final adjustment should be
checked by turning knob from high to low several times
without extinguishing the flame.
VALVE MUST BE IN THE “LOW” POSITION
AS SHOWN _bclob MAKING LOW FLOW
ADJUSTMENT ON GAS CONVERSION
This adjustment, at low setting, will automatically provide
the proper flame size at medium setting.
),*85( HOLD VALVE STEM IN “LOW”
POSITION WHILE MAKING
SCREW ADJUSTMENT FOR
GAS CONVERSION
TURN ADJUSTMENT SCREW
ABOUT 1/4 OF A TURN TO
ADJUST FOR LP GAS
),*85( 8
©2003 Maytag Appliances Company
16022498
A–9