Bosch MIC400 PTZ Specifications

MIC-BP4 Bi-Phase Converter Card
for the MIC400 PTZ Camera Series
Bosch Security Systems
EN
Installation and Operation Manual
BP4 Bi-phase card | Installation and Operation Manual
AAAEN| 2
MIC-BP4 Bi-Phase Converter Card
For the MIC400 series camera
Chapters
1. Introduction
2. MIC-BP4 Bi-phase Converter Card
3. Technical Specifications
Bosch Security Systems
Issue 1
BP4 Bi-phase card | Installation and Operation Manual
AAAEN| 3
Introduction............................................................... 1-6
MIC-BP4 Bi-Phase Converter Card….................................................
Versions..............................................................................................
Features..............................................................................................
Unpacking...........................................................................................
Package Contents...............................................................................
1-7
1-7
1-7
1-7
1-7
MIC-BP4 Bi-phase Converter Card………...……….. 2-8
Bi-phase Telemetry Specifications………………………………………
Typical Wiring Example…………………………………………………..
Installation of the MIC-BP4 Bi-phase Converter Card…………………
Setting the MIC400 address (in hardware)……………........................
Troubleshooting……………………………………………………………
MIC Address DIP Switch Settings…………………………...................
2-8
2-9
2-9
2-10
2-10
2-11
Technical Specifications............................................ 3-12
Technical Specifications………………………………………………….
Bosch Security Systems
Issue 1
3-12
Intentionally Blank
BP4 Bi-phase card | Installation and Operation Manual
Safety Precautions
The following symbols are used throughout this manual please pay careful
attention to their meaning.
The lightning flash with an arrowhead symbol within a triangle
is intended to alert the user to the presence of non-insulated
“dangerous voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock
to persons.
The exclamation point within a triangle is intended to alert the
user to the presence of important safety, operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.
AAAEN| 4
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Important Safety Instructions
CAUTION
TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DISCONNECT POWER SUPPLY BEFORE OPENING THE
POWER SUPPLY UNIT.
POWER DISCONNECT: POWER SUPPLY UNITS HAVE
POWER SUPPLIED WHENEVER THE POWER CORD IS
INSERTED INTO THE POWER SOURCE
WARNING
INSTALLATION SHOULD BE CARRIED OUT BY QUALIFIED
PERSONNEL ONLY IN ACCORDANCE WITH THE
APPLICABLE LOCAL CODES.
BOSCH SECURITY SYSTEMS ACCEPTS NO LIABILITY
FOR ANY DAMAGES OR LOSSES CAUSED DUE TO
INCORRECT OR IMPROPER INSTALLATION
Bosch Security Systems
Issue 1
13.
14.
15.
Read all instructions prior to installation.
Keep this manual for future reference.
Heed all warnings.
Install according to manufacturer’s instructions.
Qualified persons only should install this product, if in doubt consult a qualified
installer.
Use correct electrostatic discharge handling procedures when handling printed
circuit boards to avoid damage to electro-sensitive components.
Do not install near any strong heat sources such as furnaces.
Never push objects or pour liquids into the product enclosure as this can cause a
fire or electrical shock hazard.
Only use electronic cleaning solvent in the unlikely event of the card requiring
cleaning.
Ensure that the product is correctly earthed.
Use only the power sources indicated in this user guide and ensure that the
current rating of the supply cable is adequate for the product.
Do not overload power supply sockets as this can be a fire or electrical shock
hazard.
In the event of failure do not attempt to service this product yourself, please
contact Bosch Security Systems for assistance.
Only use approved attachments or accessories specified by the manufacturer. Any
changes or modifications made to the equipment, not expressly approved in writing
by Bosch Security Systems, could prevent proper or safe operation of the product
and will invalidate the warranty.
Please dispose of disused electrical & electronic equipment at an environmentally
compatible recycling facility (contact Bosch Security Systems for further details).
BP4 Bi-phase card | Installation and Operation Manual
This product complies with the following EC directives:EMC Directive (89/336/EC as amended)
Machinery Directive (98/37/EC)
LV Directive (73/23/EC)
RoHS (Restriction of Hazardous substances) 2002/95/EC
WEEE (Waste Electrical & Electronic Equipment) 2002/96/EC
This equipment contains electrical or electronic components
that must be recycled properly to comply with Directive
2002/96/EC of the European Union regarding the disposal of
waste electrical and electronic equipment (WEEE). Contact
your local supplier for procedures for recycling this equipment.
Bosch Security Systems
Issue 1
AAAEN| 5
Reference
Glossary of Terms
PTZ
Bi-phase
PSU
IR
-
MIC-BP4
STP
-
Pan/Tilt/Zoom
Bosch Bi-phase telemetry protocol (see pg8)
Power Supply Unit
Infra Red (MIC cameras with IR lamps MUST use
an IR psu)
Bi-phase converter card for non-IR power supplies
Shielded Twisted Pair cable
BP4 Bi-phase card | Installation and Operation Manual
Intentionally Blank
AAAEN| 6
CHAPTER 1
Introduction
The MIC-BP4 Bi-phase converter card allows translation of the Bosch Bi-phase
protocol signals to RS485, half duplex telemetry signals. This enables Bosch
Security Systems MIC400 series PTZ cameras to interface with Bosch Bi-phase
equipment.
The MIC-BP4 Bi-phase converter card also enables the camera address to be set
through its integrated DIP switch selector.
Bosch Security Systems
Issue 1
BP4 Bi-phase card | Installation and Operation Manual
AAAEN| 7
Versions
MIC-24PSU
-
1 expansion slot; BP3 or BP4
This manual covers the installation and operation of Bosch Security Systems
MIC-BP4 Bi-phase converter card can be fitted in MIC400 power supplies which
have a free expansion slot (header CN2).
MIC-115PSU
-
1 expansion slot; BP3 or BP4
MIC-THERMAL-PSU
-
1 expansion slot; BP3 or BP4
For MIC400IR cameras please refer to the MIC-BP3 Bi-phase converter card
manual.
MDPS PSU’s
-
BP3 or BP4 depending on availability of
expansion slot.
CAUTION: The MIC-BP4 converter card can only be used
with MIC400 Non - IR variant power supplies due to a lack of
an expansion slot in the IR variant power supplies. Please
ensure the correct Bi-phase card for the type of power supply
is used (see below).
For customers requiring RS485 to Bosch Bi-phase protocol translation using other
MIC400 power supply variants; please refer to the following list to select the
correct card for the appropriate power supply:-
Unpacking
•
Check the exterior of the packaging for visible damage. If any items
appear to have been damaged in transit please inform the shipping
company.
•
Unpack the card carefully; this is electronic equipment and should be
handled with care.
•
Do not use if any component appears to be damaged. Please contact
Bosch Security Systems in the event of damaged goods.
•
The shipping carton is the best way to transport the unit, save it and all
other packaging materials for future use. If the part must be returned, use
the original packing materials.
Converter Card Type
MIC-BP3
-
Card is mounted in an external enclosure for PSU’s
Without an expansion slot available (header CN2), can be
used with any MIC-PSU.
MIC-BP4
-
Plug in card for power supplies were the CN2 expansion
slot is available.
MIC PSU
CAUTION: Use proper ESD handling precautions to avoid
electrostatic discharge. Wear a grounded wrist strap to
prevent damage when handling electro-sensitive printed
circuit boards.
BP Converter Card Type
MIC-IR-PSU (all types) -
No expansion slot; BP3 Only
MIC-240PSU
-
1 expansion slot; BP3 or BP4
MIC-12PSU
-
1 expansion slot; BP3 or BP4
Bosch Security Systems
Issue 1
Packaging Contents
Please check for the following contents
•
•
MIC-BP4 Bi-Phase converter card installation manual (this guide)
MIC-BP4 Bi-Phase card
BP4 Bi-phase card | Installation and Operation Manual
CHAPTER 2
MIC-BP4 Bi-phase Converter Card
Picture 1 – The MIC-BP4 Bi-phase converter card for MIC400 series power
supplies.
AAAEN| 8
Bi-phase Telemetry Specifications
Shielded 2-wire, half-duplex, multi-drop, 5000 ft. cable limit, 18AWG gauge needed
for 500ft distance.
Bi-phase is the standard Bosch protocol used to send Pan/Tilt/Zoom control over
2-wire shielded twisted pair (STP) terminated with an 110Ω terminal resistor.
Cable Type
STP - Shielded Twisted Pair
Distance
1524 m (5000 ft) Belden 8760 recommended
Transmission Rate
Gage
31.25 KHz
1.02 mm (18 AWG)
Termination
110 Ω
Terminal Connector
Screw terminals
Voltage
4 Vp-p
Figure 1 below illustrates the connections necessary for Bi-phase operation.
The Bi-phase converter card allows Bosch control systems with Bi-phase output to
control up to eight (8) non-IR MIC400 series camera via their associated power
supply units.
1
2
3
Bi-phase to RS485 Converter PCB
Bi-phase output on Control System
HD2 Screw Terminal Header
Figure 1: Connections for Bi-phase
Bosch Security Systems
Issue 1
BP4 Bi-phase card | Installation and Operation Manual
CAUTION: The shield must be connected to the controller end only
The MIC-BP4 has a 110 Ω termination resistor between the Bi-phase +ve and –ve
terminals which should be removed unless the camera is the last in the daisy chain
of cameras.
Typical Wiring Example
In a daisy chain configuration (as shown in Figure 2 below), a termination resistor
of 110 Ω must be added to the last MIC400 in the series. You can daisy chain a
maximum of eight (8) MIC400’s per Bi-phase output.
AAAEN| 9
Installation of the MIC-BP4 Bi-phase Converter Card
1. The power supply unit should be switched off and unplugged prior to
carrying out any work.
2. Ensure that the four (4) card spacer supports fitted in the power supply are
positioned in the centre and right most mounting holes on the power
supply printed circuit board, so that the MIC-BP4 card is supported in each
corner.
3. To reposition the card spacers first remove the four (4) screws holding the
power supply PCB to the enclosure, turn the PCB over and remove the
two (2) card spacer supports at the right hand positions (labelled A on
Figure 3), these spacers should be re-fixed at the middle positions
(labelled B on Figure 3).
4. Connect the Bi-phase +, Bi-phase - signals in the Shielded Twisted Pair
(STP) cable from the control system to the appropriate HD2 screw
terminals (as shown in Figure 1).
5. Insert the MIC-BP4 card into the connector labelled CN2 (labelled C on
Figure 3) on the PSU, and screw to the card spacer supports using M3x6
screws.
6. Switch on the power supply unit.
7. A status LED will flash (every 3 seconds) indicating the operation of the
BP4 Bi-phase converter.
8. To verify the Bi-phase signal are being received and converted, send a
PTZ commands from the control system. The status LED will flash whilst
commands are being converted to RS485.
Figure 2: Daisy chain configuration for Bi-phase controller
Bosch Security Systems
Issue 1
BP4 Bi-phase card | Installation and Operation Manual
CAUTION: The shield must be connected to the
controller end only
Figure 3 – Layout of a MIC400 Non-IR Power Supply PCB
(MIC-240PSU, MIC-012PSU, MIC-024PSU & MIC-115PSU)
AAAEN| 10
Setting the MIC400 Address (in Hardware)
The MIC-BP4 Bi-phase converter card supports changing the address of the
MIC400 at the pole base through hardware.
It should be noted that the MIC-BP4 converts all Bi-phase data into RS485 data
regardless of the address setting on the DIP switches. The MIC400 will filter and
process commands that match the current address of the MIC400.
The address setting procedure is as follows:
1.
Select the appropriate address (1-255) by setting up the DIP switches. (See
tables below)
2.
Press the push button (SW2) adjacent to the DIP switches to set the address.
3.
The status LED will flash once indicating the start of the address setting
procedure. You should then observe the MIC400 panning this confirms that
the MIC400 has been set to the new address.
4.
The status LED will be illuminated for the duration of this procedure.
Troubleshooting
1. The status LED does not flash when sending commands from the control
system.
a. Check the polarity of Bi-phase signal cables connected on the MIC-BP4.
b. Ensure the power supply is switch on.
Bosch Security Systems
Issue 1
BP4 Bi-phase card | Installation and Operation Manual
1 to 127 DIP Switch Address Settings for MIC400 series cameras
Bosch Security Systems
Issue 1
AAAEN| 11
128 to 255 DIP Switch Address Settings for MIC400 series cameras
BP4 Bi-phase card | Installation and Operation Manual
CHAPTER 3
Technical Specifications
Physical Dimensions and Cable Specification
MIC-BP4 card dimensions
60 mm (W) x 10mm (H) x 70mm (D)
Recommended cable type
Cable Type
Distance
Transmission Rate
STP - Shielded Twisted Pair
1524 m (5000 ft) Belden 8760 recommended
31.25 KHz
Gage
Termination
1.02 mm (18 AWG)
Terminal Connector
Screw terminals
Voltage
4 Vp-p
110 Ω
Bi-phase Specifications: - Shielded 2-wire, half-duplex, multi-drop, 5000 ft cable
limit, 18 AWG gauge wire needed for 5000ft distance.
AAAEN| 12
Contact
Americas
Bosch Security Systems Inc
850 Greenfield Road
Lancaster
Pennsylvania 17601
USA
Telephone
+1 888-289-0096
Fax
+1 585-223-9180
Email: security.sales@us.bosch.com
www.boschsecurity.us
Europe, Middle East, Africa
Bosch Security Systems B.V
P.O Box 80002
5600 JB Eindhoven
The Netherlands
Phone
+31 40 2577 284
Fax
+31 40 2577 330
emea.securitysystems@bosch.com
www.boschsecurity.com
Asia-Pacific
Bosch Security Systems Pte Ltd
38C Jalan Pemimpin
Singapore 577180
Phone
+65 6319 3450
Fax
+65 6319 3499
apr.securitysystems@bosch.com
www.boschsecurity.com
© Bosch Security Systems B.V, 2009, Data subject to change without
Bosch Security Systems
Issue 1