Keypad Locks
Programming Guide
23780034
Codes
Programming Code (Six Numbers)
•Used to program the lock.
•DOES NOT unlock the lock.
•If you forget the Programming
Code, you can reset your lock back to factory settings. See the
Keypad Locks User Guide for more information.
•Lock comes preset with a default
Programming Code.
User Codes (Four Numbers)
•Used to unlock the lock.
•Up to 19 possible User Codes can be stored in the lock at a time.
•Lock comes preset with two default User Codes.
Default Programming Code
Código de programación predeterminado
Code du défaut programmation
Place Label Here
Poner la etiqueta aquí
Placer l’autocollant ici
Default User Codes
Códigos de usuario predeterminado
Codes du défaut utilisateur
Functions
See reverse for function descriptions. Beeps sound only when beeper is enabled.
U
Add ser Code
Delete
User Code
Change
Programming
Code
Enable
Vacation Mode
Enable/Disable
Beeper
Delete ALL
User Codes
Enable/Disable
Turn Lock
Feature
Enter
Programming Code
(six numbers)
Waitfor
3 Lights+ 3 Beeps
Press turns blue
Enter
Programming Code
(six numbers)
Waitfor
3 Lights+ 3 Beeps
Enter Current
Programming Code
(six numbers)
Waitfor
3 Lights+ 3 Beeps
Enter
Programming Code
(six numbers)
Waitfor
3 Lights+ 3 Beeps
Enter
Programming Code
(six numbers)
Waitfor
3 Lights+ 3 Beeps
Enter
Programming Code
(six numbers)
Waitfor
3 Lights+ 3 Beeps
Enter
Programming Code
(six numbers)
Waitfor
3 Lights+ 3 Beeps
Press
Keypad turns blue
Press
Keypad turns blue
Press
Press
Keypad turns blue
Press
Keypad turns blue
Press
Keypad turns blue
Press
Waitfor
3 Lights+ 3 Beeps
Press
Waitfor
3 Lights+ 3 Beeps
Press
Waitfor
3 Lights+ 3 Beeps
Press
Success!
1 Light+ 1 Long Beep
Press
Enter Unwanted
User Code
(four numbers)
Waitfor
3 Lights+ 3 Beeps
Enter New
Programming Code
(six numbers)
Waitfor
3 Lights+ 3 Beeps
Disable
Vacation Mode
Success!
Enter New
User Code
(four numbers)
Waitfor
3 Lights+ 3 Beeps
1 Light+ 1 Long Beep
Press
Waitfor
Enter
Programming Code
(six numbers)
Success!
3 Lights+ 3 Beeps
Press
Success!
1 Light+ 1 Long Beep
1 Light+ 1 Long Beep
Enter Same New
User Code
(four numbers)
Success!
1 Light+ 1 Long Beep
Enter Same Unwanted
User Code
(four numbers)
Success!
1 Light+ 1 Long Beep
Enter Same New
Programming Code
(six numbers)
Success!
1 Light+ 1 Long Beep
Enter
Programming Code
(six numbers)
Success!
1 Light+ 1 Long Beep
Function Descriptions
Add User Code
• Adds one User Code to the lock.
Delete User Code
• Deletes one User Code from the lock.
Change Programming Code
• Changes the Programming Code.
Enable/Disable Vacation Mode
• When Vacation Mode is enabled, User Codes will not unlock the lock.
• Used to ensure lock remains secure while you are away from home.
• Disable vacation mode to resume normal operation.
Error Indications
Enable/Disable Beeper
• When the beeper is enabled, the lock will beep once with each key press, and multiple times for other indications.
Delete All User Codes
• Deletes all the User Codes from the lock at once.
Enable/Disable Turn Lock Feature
• Applies to Keypad Deadbolt (BE365) only.
• Enabled by default. Allows easy re-locking of deadbolt from the outside.
• When disabled, a valid user code must be entered to lock the deadbolt from the outside.
Problem
User Code does not unlock lock.
Beeps* Lights Solution
2
1 High,
1 Low then
User Code entered is not a valid User Code.
Vacation Mode is enabled. Disable Vacation Mode.
Nothing happens when numbers are pressed.
There is a delay before unlock after a valid User Code is entered.
blinking but no codes have been entered.
Cannot add a new User Code.
Cannot delete a User Code.
Cannot delete all User Codes.
Cannot change Programming Code.
Lock will not stay in programming mode.
* Beeps sound only when beeper is enabled.
None None
Too many incorrect User Codes have been entered.
Wait 30 seconds and try again.
If keypad does not respond after 30 seconds, then replace battery.
High/
Low, then 1
None
2
2
High/Low
2
2 then
Blinking
Battery is low and should be replaced. See the
Keypad Locks User Guide.
Battery is dead and MUST be replaced. See the
Keypad Locks User Guide.
19 User Codes already exist. Delete a User Code before adding a new one.
Second User Code entered did not match first User
Code entered.
The User Code matches the first four digits of the existing Programming Code.
Second User Code entered did not match first User
Code entered.
Second Programming Code entered did not match first Programming Code entered.
First four digits of new Programming Code match an existing User Code.
Programming Code entered second time is incorrect.
2
Any key other than was pressed immediately after the programming code was entered.
An incorrect entry was made during the programming process.
keypad.schlage.com
Need Help?
Calling From:
U.S.A.: (888) 805-9837
Canada: (800) 997-4734
Mexico: 018005067866
Get the free mobile app at gettag.mobi
©2011 Schlage Lock Company
Printed in U.S.A.
23780034 Rev. 04/11-a
