x Permacron® Special Silver MB 560

x Permacron® Special Silver MB 560
293.560
14 V.1
Technical Data Sheet
Permacron® Base Coat Special Silver
Repair Process
Example: Nissan KAB Bluish Silver
®
Permacron Special Effect Base Coat using limited use mixing color MB560 for Nissan code KAB used on
the Nissan GTR.
Special procedures are required for the repair process of these
unique finishes
This product is for professional painting of vehicles only.
Technical Data Sheet No. XXX. Mar. 2014
 2014 Axalta Coating Systems, LLC and all affiliates. All rights reserved.
293.560
14 V.1
Suitable Substrates:
Original or old paintwork (except reversible substrates)
®
Priomat Surfacers
®
Permacron Primer/Surfacers
®
Permahyd Primer/Surfacers
®
Permasolid Surfacers
Substrate pretreatment:
Degrease and sand.
Before further treatment, clean all substrates thoroughly with
Permaloid Silicone Removers 7087 or 7010 Slow, Permahyd Silicone Remover
7085, or Permahyd Silicone Remover 7096.
Application:
Step one
(ground coat):
Apply Ground color to repair area. (See Mixing Information below)
Step Two:
Before applying, see Special Tips on surface preparation. Apply 1 ½ coats of
®
®
Permacron 2K Clear Coat or Permasolid HS Clear Coat over surfacer and entire
panel. Cure the clear coat.
Sand with orbital sander using P1500 – 3000. If necessary, sand edges and
corners by hand with P2000 - 3000. Do not use scuff pads. Carefully remove all
orange peel and dirt nibs. Areas where color is applied should be sanded with
P1000 -1500, areas where no color is applied should be sanded with P1500 or
finer.
Step Three:
Apply Wet-Bed over entire panel.
®
®
Wet-Bed Instructions: Mix Permacron 2K Clear Coat or Permasolid HS Clear
®
Coat as recommended then over reduce with Permacron Reducer 3363 Medium
by 300%.
Step Four
(Mid coat):
Apply Mid-coat color to panel and blend as necessary.
Mixing ratio:
®
100% Permacron Supercryl Reducers 3054 Medium or 3056 Slow.
(See Mixing Information below).
Pot Life:
Unlimited (in sealed container) Pot life for hardened basecoat is 8 hours.
 2014 Axalta Coating Systems, LLC and all affiliates. All rights reserved.
293.560
14 V.1
Application continued):
Method of application
HVLP
Approved Transfer Efficiency
Please refer to gun manufacturer and local legislation for proper spray
pressure recommendations.
Spray Nozzle
Application viscosity 4mm,
68°F/20C, DIN 4
Reducer at 68°F/20C
material temperature
1.3-1.4mm
1.2-1.3mm
approx.17 - 21 seconds
®
Mix ratio for Ground Coat - 2:1 with 15% Permasolid HS Hardener
before reduction.
Mid Coat 1:1. (100% reduction)
2 - 4 coats
Number of coats
Recommended film thickness: 2 coats = 0.6 - 0.8 mil dry film thickness
4 coats = 0.8 - 1.7 mil dry film thickness
Flash-off time (Before Clear Coat)
At 68F/ 20C
Recoat With:
10 - 15 minutes depending on reducer used.
®
®
Permacron or Permasolid Clear Coats.
®
®
Permacron or Permasolid VOC Compliant Clear Coats where required.
Nissan code KAB
Ground coat formula
Toner:
Percentage:
MB557
96.6
MB502
3.0
MB577
0.7
MB555
0.7




Mid coat formula
Toner:
Percentage:
MB560*
97.7
MB574
2.3
MB553
1.2
MB506
0.5
MB547
0.2
MB555
0.2
* Factory Pack – Special Silver
Mix ratio for Ground Coat - When using Permasolid HS Hardeners, add 15% before reduction.
When using Permasolid VHS Hardeners, add 10% before reduction.
®
2:1 with 15% Permasolid HS Hardeners 3310 Fast, 3315 Medium, or 3320 Slow before reduction.
Maximum recoat window for hardened basecoat is 8 hours.
®
Mix Ratio for Mid Coat – 1:1 with Permacron Supercryl Reducers 3054 Medium or 3056 Slow.
 2014 Axalta Coating Systems, LLC and all affiliates. All rights reserved.
293.560
14 V.1
Important Regulatory Information
Please see the appropriate VOC wall chart for compliance for your area. The values depicted below are
“ready to spray.”
VOC Category
VOC (ap/le)
Gallon
Weight
Wt% Volatiles, Water &
Exempts
Vol% Solids
Nissan KAB (293)
600 g/l limit
812 g/l, 812 g/l
7.46 lbs/gal
90.8%, 0.0%, & 0.0%
7.0%


For industrial use only by professional, trained painters. Not for sale to or use by the general
public. Before using, read and follow all label and MSDS precautions. If mixed with other
components, mixture will have hazards of all components. Ready to use paint materials
containing isocyanates can cause irritation of the respiratory organs and hypersensitive
reactions. Asthma sufferers, those with allergies and anyone with a history of respiratory
complaints must not be asked to work with products containing isocyanates. Do not sand,
flame cut, braze or weld dry coating without a NIOSH approved air purifying respirator with
particulate filters or appropriate ventilation, and gloves.
Any analytical results set forth herein do not constitute a warranty of specific product features or of the
product’s suitability for a specific purpose. All products are sold pursuant to our general conditions of
sale. We hereby disclaim all warranties and representations, express or implied, with respect to this
product, including any warranty of merchantability or fitness for a particular purpose. This product is
protected by patent law, trademark law, copyright law, international treaties and/or other applicable law.
All rights reserved. Unauthorized sale, manufacturing or use may result in civil and criminal penalties.
SPIES HECKER, INC.
47818 West Anchor Court
Plymouth, MI 48170
Tel. 800-447-7437 (800-44-SPIES)
Fax 734-354-3405
www.SpiesHeckerUSA.com
 2014 Axalta Coating Systems, LLC and all affiliates. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement