QG 2950
Vigor2950 Series
Security VPN Router
Quick Start Guide
Version: 1.1
Date: 2006/11/20
i
Copyright Information
Copyright
Declarations
Copyright 2006 All rights reserved. This publication contains information that is
protected by copyright. No part may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language without written
permission from the copyright holders.
Trademarks
The following trademarks are used in this document:
z
Microsoft is a registered trademark of Microsoft Corp.
z
Windows, Windows 95, 98, Me, NT, 2000, XP and Explorer are
trademarks of Microsoft Corp.
z
Apple and Mac OS are registered trademarks of Apple Computer Inc.
z
Other products may be trademarks or registered trademarks of their
respective manufacturers.
Safety Instructions and Approval
Safety
Instructions
Warranty
z
z
Read the installation guide thoroughly before you set up the router.
The router is a complicated electronic unit that may be repaired only be
authorized and qualified personnel. Do not try to open or repair the router
yourself.
z
Do not place the router in a damp or humid place, e.g. a bathroom.
z
The router should be used in a sheltered area, within a temperature range
of +5 to +40 Celsius.
z
Do not expose the router to direct sunlight or other heat sources. The
housing and electronic components may be damaged by direct sunlight or
heat sources.
z
Do not deploy the cable for LAN connection outdoor to prevent electronic
shock hazards.
z
Keep the package out of reach of children.
z
When you want to dispose of the router, please follow local regulations on
conservation of the environment.
We warrant to the original end user (purchaser) that the router will be free from
any defects in workmanship or materials for a period of two (2) years from the
date of purchase from the dealer. Please keep your purchase receipt in a safe
place as it serves as proof of date of purchase. During the warranty period, and
upon proof of purchase, should the product have indications of failure due to
faulty workmanship and/or materials, we will, at our discretion, repair or replace
the defective products or components, without charge for either parts or labor, to
whatever extent we deem necessary tore-store the product to proper operating
condition. Any replacement will consist of a new or re-manufactured
functionally equivalent product of equal value, and will be offered solely at our
discretion. This warranty will not apply if the product is modified, misused,
tampered with, damaged by an act of God, or subjected to abnormal working
conditions. The warranty does not cover the bundled or licensed software of
other vendors. Defects which do not significantly affect the usability of the
product will not be covered by the warranty. We reserve the right to revise the
manual and online documentation and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or
changes.
Be a Registered
Owner
Web registration is preferred. You can register your Vigor router via
http://www.draytek.com.
Firmware & Tools
Updates
Due to the continuous evolution of DrayTek technology, all routers will be
regularly upgraded. Please consult the DrayTek web site for more information on
newest firmware, tools and documents.
http://www.draytek.com
i
European Community Declarations
Manufacturer:
Address:
Product:
DrayTek Corp.
No. 26, Fu Shing Road, HuKou County, HsinChu Industrial Park, Hsin-Chu, Taiwan 303
Vigor2950 Series Router
DrayTek Corp. declares that Vigor2950 Series of routers are in compliance with the following essential
requirements and other relevant provisions of R&TTE Directive 1999/5/EEC.
The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive
89/336/EEC by complying with the requirements set forth in EN55022/Class A and EN55024/Class A.
The product conforms to the requirements of Low Voltage (LVD) Directive 73/23/EEC by complying with
the requirements set forth in EN60950.
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the use is encouraged to try to correct the interference
by one of the following measures:
z
Reorient or relocate the receiving antenna.
z
Increase the separation between the equipment and receiver.
z
Connect the equipment into an outlet on a circuit different form that to which the receiver is
connected.
z
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device may accept any interference received, including interference that may cause undesired
operation.
Taiwanese BSMI (Bureau of Standards, Metrology and Inspection) A Warning:
Warning: This device might cause interference of radio frequency under the environment of dwelling. In
such condition, the users might be asked to adopt some proper strategies.
Please visit www.draytek.com/about_us/Regulatory.php.
This product is designed for the 2.4 GHz WLAN network throughout the EC region and Switzerland with
restrictions in France.
This is a class A product. In a domestic environment, this product may cause radio interference in which
case the user may be required to take adequate measures.
ii
Table of Contents
1. Introduction........................................................................................................... 1
1.1 Panel Explanation ...................................................................................................................... 2
1.1.1 For Vigor2950 ............................................................................................................... 2
1.1.2 For Vigor2950G............................................................................................................. 3
1.1.3 For Vigor2950i............................................................................................................... 4
1.1.4 For Vigor2950Gi............................................................................................................ 5
1.2 Package Content........................................................................................................................ 6
2. Installing Your Router........................................................................................... 7
2.1 Hardware Installation.................................................................................................................. 7
3. Configuring Web Pages ....................................................................................... 9
3.1 Basic Configuration .................................................................................................................... 9
3.2 Wireless LAN Settings (for G Series Model Only) ................................................................... 13
3.2.1 Basic Wireless LAN Concept ...................................................................................... 13
3.2.2 General Settings ......................................................................................................... 13
3.2.3 Security Settings ......................................................................................................... 15
4. Trouble Shooting ................................................................................................ 17
4.1 Checking If the Hardware Status Is OK or Not......................................................................... 17
4.2 Checking If the Network Connection Settings on Your Computer Is OK or Not ...................... 17
4.3 Pinging the Router from Your Computer .................................................................................. 20
4.4 Checking If the ISP Settings are OK or Not ............................................................................. 21
4.5 Backing to Factory Default Setting If Necessary...................................................................... 23
4.6 Contacting Your Dealer ............................................................................................................ 24
iii
1. Introduction
Vigor2950 is a broadband router with dual-WAN interface. It provides policy-based
load-balance, fail-over and BoD (Bandwidth on Demand), also it integrates IP layer QoS,
NAT session/bandwidth management to help users control works well with large
bandwidth.
By adopting hardware-based VPN platform, hardware encryption of AES/DES/3DS and
hardware key hash of SHA-1/MD5, the router increases the performance of VPN greatly,
and offers several protocols (such as IPSec/PPTP/L2TP) with up to 200 VPN tunnels.
The object-originated design used in SPI (Stateful Packet Inspection) firewall allows
users to set firewall policy with ease. CSM (Content Security Management) provides
users control and management in IM (Instant Messenger) and P2P (Peer to Peer) more
efficiency than before. By the way, DoS/DDoS prevention and URL/Web content filter
strengthen the secuirty outside and control inside.
With the high performance of SuperGTM in wireless, the router allows the connection rate
up to 108Mbps. Except the encryption methods of WEP/WPA/WPA2 and MAC address
control, it also offers wireless LAN isolation, Wireless VLAN and 802.1x authentication.
WDS (Wireless Distribution System) can help users to expand wireless coverage easily.
Moreover, the wireless rate control can manage the connection rate of wireless station. In
addition, ISDN function provides users a flexible network backup and remote control
ability in a secure way.
Features for Vigor2950
z
Dual WAN: Support policy-based load-balance, bandwidth on demand and internet
connection failover
z
Gigabit Ethernet LAN: 1000Mbps fast LAN traffic switching
z
Object-originated Firewall: Provide SPI, DoS/DDoS prevention, CSM(Content Security
Management)
z
Content Filter: URL and Web (powered by SurfControl Content filtering)
z
VPN: Hardware-based VPN support up to 200 VPN Tunnels
z
z
Bandwidth Management: IP layer QoS and NAT session/bandwidth management
Wireless: 108Mbps SuperGTM supports WEP/WPA/WPA2 and MAC address
control, wireless LAN isolation, Wireless VLAN and 802.1x authentication
ISDN: Internet access backup and remote dial-in
z
1
1.1 Panel Explanation
1.1.1 For Vigor2950
LED
Status
Explanation
ACT (Activity)
Blinking
Off
On
On
On
Off
On
The router is powered on and running normally.
The router is powered off.
DMZ Host is specified in certain site.
LAN traffic monitor is active.
The VPN tunnel is launched.
The VPN tunnel is closed.
The QoS function is active.
On
Off
Blinking
On
Off
Blinking
On
Off
Blinking
On
Off
Blinking
The port is connected with 10Mbps.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is disconnected.
The data is transmitting.
The port is connected with 1000Mbps.
The port is disconnected.
The data is transmitting.
DMZ
Monitor
VPN
QoS
LED on Connector
10
(left LED)
WAN
100
(right LED)
LAN/Monitor
LAN
100
(left LED)
1000
(right LED)
Interface
Description
RST
(Factory Reset)
Restore the default settings.
Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for
more than 5 seconds. When you see the ACT LED begins to blink rapidly than
usual, release the button. Then the router will restart with the factory default
configuration.
Connecter for remote networked devices.
Connecter for local networked devices.
Connecter for local networked devices.
Connecter for a power cord with 100-240VAC (inlet).
WAN(1/2)
LAN/Monitor
LAN (1-4)
Power Switch. “1” is ON; “0” is OFF.
2
1.1.2 For Vigor2950G
LED
Status
Explanation
ACT (Activity)
Blinking
Off
On
On
On
Off
On
The router is powered on and running normally.
The router is powered off.
DMZ Host is specified in certain site.
LAN traffic monitor is active.
The VPN tunnel is launched.
The VPN tunnel is closed.
The QoS function is active.
On
Blinking
Off
Wireless access point is ready.
Ethernet packets are transmitting over wireless LAN.
The WLAN function is inactive.
On
Off
Blinking
On
Off
Blinking
On
Off
Blinking
On
Off
Blinking
The port is connected with 10Mbps.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is disconnected.
The data is transmitting.
The port is connected with 1000Mbps.
The port is disconnected.
The data is transmitting.
DMZ
Monitor
VPN
QoS
WLAN
LED on Connector
10
(left LED)
WAN
100
(right LED)
LAN/Monitor
LAN
100
(left LED)
1000
(right LED)
Interface
Description
RST
(Factory Reset)
Restore the default settings.
Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for
more than 5 seconds. When you see the ACT LED begins to blink rapidly than
usual, release the button. Then the router will restart with the factory default
configuration.
Connecter for remote networked devices.
Connecter for local networked devices.
Connecter for local networked devices.
Connecter for a power cord with 100-240VAC (inlet).
WAN(1/2)
LAN/Monitor
LAN (1-4)
Power Switch. “1” is ON; “0” is OFF.
3
1.1.3 For Vigor2950i
LED
Status
Explanation
ACT (Activity)
Blinking
Off
On
On
On
Off
On
The router is powered on and running normally.
The router is powered off.
DMZ Host is specified in certain site.
LAN traffic monitor is active.
The VPN tunnel is launched.
The VPN tunnel is closed.
The QoS function is active.
On
Blinking
The ISDN service function is active.
A successful connection on the ISDN BRI B1/B2
channel.
On
Off
Blinking
On
Off
Blinking
On
Off
Blinking
On
Off
Blinking
The port is connected with 10Mbps.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is disconnected.
The data is transmitting.
The port is connected with 1000Mbps.
The port is disconnected.
The data is transmitting.
DMZ
Monitor
VPN
QoS
ISDN
LED on Connector
10
(left LED)
WAN
100
(right LED)
LAN/Monitor
LAN
100
(left LED)
1000
(right LED)
Interface
Description
RST
(Factory Reset)
Restore the default settings.
Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for
more than 5 seconds. When you see the ACT LED begins to blink rapidly than
usual, release the button. Then the router will restart with the factory default
configuration.
Connect for NT1 (or NT1+) box provided by ISDN service provider.
Connecter for remote networked devices.
Connecter for local networked devices.
Connecter for local networked devices.
Connecter for a power cord with 100-240VAC (inlet).
ISDN
WAN(1/2)
LAN/Monitor
LAN (1- 4)
Power Switch. “1” is ON; “0” is OFF.
4
1.1.4 For Vigor2950Gi
LED
Status
Explanation
ACT (Activity)
Blinking
Off
On
On
On
Off
On
The router is powered on and running normally.
The router is powered off.
DMZ Host is specified in certain site.
LAN traffic monitor is active.
The VPN tunnel is launched.
The VPN tunnel is closed.
The QoS function is active.
On
Blinking
Off
On
Blinking
Wireless access point is ready.
Ethernet packets are transmitting over wireless LAN.
The WLAN function is inactive.
The ISDN service function is active.
A successful connection on the ISDN BRI B1/B2
channel.
On
Off
Blinking
On
Off
Blinking
On
Off
Blinking
On
Off
Blinking
The port is connected with 10Mbps.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is disconnected.
The data is transmitting.
The port is connected with 1000Mbps.
The port is disconnected.
The data is transmitting.
DMZ
Monitor
VPN
QoS
WLAN
ISDN
LED on Connector
10
(left LED)
WAN
100
(right LED)
LAN/Monitor
LAN
100
(left LED)
1000
(right LED)
Interface
Description
RST
(Factory Reset)
Restore the default settings.
Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for
more than 5 seconds. When you see the ACT LED begins to blink rapidly than
usual, release the button. Then the router will restart with the factory default
configuration.
Connect for NT1 (or NT1+) box provided by ISDN service provider.
Connecter for remote networked devices.
Connecter for local networked devices.
Connecter for local networked devices.
Connecter for a power cord with 100-240VAC (inlet).
ISDN
WAN(1/2)
LAN/Monitor
LAN (1- 4)
Power Switch. “1” is ON; “0” is OFF.
5
1.2 Package Content
nQuick Start Guide
oCD
p Antenna for G models
qRJ-45 Cable (Ethernet)
r RJ-45 to RJ-45 Cable for i models
s The type of the power adapter depends on the country that the router will be installed:
UK-type power cord
EU-type power cord
USA/Taiwan-type power cord
AU/NZ-type power cord
* The maximum power consumption is 17 Watt.
6
2. Installing Your Router
This section will guide you to install the router through hardware connection and
configure the router’s settings through web browser.
2.1 Hardware Installation
Before starting to configure the router, you have to connect your devices correctly.
1.
Connect the power cord to the router’s power port on the rear panel, and the other
side into a wall outlet.
2.
Power on the device by pressing down the power switch on the rear panel.
3.
The system starts to initiate. After completing the system test, the ACT LED will
light up and start blinking.
4.
Connect one end of an Ethernet cable (RJ-45) to one of the LAN ports of the router
and the other end of the cable (RJ-45) into the Ethernet port on your computer (that
device also can connect to other computers to form a small area network). The LAN
LED (Left or Right) will light up according to the network card feature (1000 or 100)
of the device that it connected.
5.
Connect a cable Modem/DSL Modem/Media Converter (depends on your
requirement) to any WAN port of router with Ethernet cable (RJ-45). The
WAN1/WAN2 LED (Left or Right) will light up according to the network card
feature (100 or 10) of the device that it connected.
(For the detailed information of LED status, please refer to section 1.1.)
7
This page is left blank.
8
3. Configuring Web Pages
3.1 Basic Configuration
The Quick Start Wizard is designed for you to easily set up your router for Internet
access. You can directly access the Quick Start Wizard via Web Configurator.
1.
Make sure your PC connects to the router correctly.
Notice: You may either simply set up your computer to get IP dynamically
from the router or set up the IP address of the computer to be the same
subnet as the default IP address of Vigor router 192.168.1.1. For the
detailed information, please refer to the later section - Trouble Shooting of
the guide.
2.
Open a web browser on your PC and type http://192.168.1.1. A pop-up window will
open to ask for username and password. Do not type any word on the window and
click OK for next screen.
Notice: If you fail to access to the web configuration, please go to “Trouble
Shooting” for detecting and solving your problem.
3.
Now, the Main Screen will pop up. Click Quick Start Wizard.
9
4.
Enter the login password on the field of New Password and retype it on the field of
Retype New Password. Then click Next to continue.
5.
On the next page as shown below, please select the WAN interface that you use.
Choose Auto negotiation as the physical type for your router. Then click Next for
next step.
6.
On the next page as shown below, please select the appropriate Internet access type
according to the information from your ISP. For example, you should select PPPoE
mode if the ISP provides you PPPoE interface. Then click Next for next step.
10
PPPoE: if you click PPPoE or PPPoA as the protocol, please manually enter the
Username/Password provided by your ISP. Then click Next.
PPTP: if you click PPTP, you will get the following page. Please type in all the
information originally provided by your ISP. Then click Next for next step.
Static IP: if you click Static IP, you will get the following page. Please type in the IP
address information originally provided by your ISP. Then click Next for next step.
11
DHCP: if you click DHCP, you will get the following page. Simply click Next to
continue.
7.
Now you can see the following screen. It indicates that the setup is complete.
Different types of connection modes will have different summary. Click Finish and
then restart the router. Afterward, you will enjoy surfing on the Internet.
12
3.2 Wireless LAN Settings (for G Series Model Only)
For operating G Series well, it is necessary for you to set the wireless LAN settings for
using wireless function. Please read the following section carefully for configuring the
settings for this router.
(The default value of Frequency Domain was set by factory depends on the reselling
region.)
3.2.1 Basic Wireless LAN Concept
In an Infrastructure Mode of wireless network, Vigor wireless router plays a role as an
Access Point (AP) connecting to lots of wireless clients or Stations (STA). All the STAs
will share the same Internet connection with other wired hosts via Vigor wireless router.
Client
Client
WPA/WPA2
Internet
ADSL2+
AP
3.2.2 General Settings
1.
On the Wireless LAN group, select General Settings. The following page will be
shown.
13
2.
Check the box Enable Wireless LAN to enable the wireless function.
3.
Select an appropriate wireless mode.
The router can connect to IEEE802.11b, IEEE802.11g and
Mixed
(11b+11g+SuperG) SuperG stations simultaneously. Please choose this mode if
your WLAN clients have such features.
The router can connect to IEEE802.11b and IEEE802.11g
Mixed (11b+11g)
stations simultaneously. This is default settings. Choose this
mode if you have no idea to change the mode.
The router can connect to SuperG stations only.
SuperG only
4.
11g-only
The router can connect to IEE802.11g stations only.
11b-only
The router can connect to IEE802.11b stations only.
Type in the name of the SSID and Channel. The default name for SSID is default.
We suggest you change it to a particular name for your necessity.
SSID (service set
identifier)
It is used to name the wireless LAN for this router, and it must
have the same content in client PC/notebook wireless card(s).
SSID can be any text numbers or various special characters.
Channel
It is a wireless channel for the router. The default channel is 6.
You can change it to an appropriate one if the selected
channel is under serious interference.
14
3.2.3 Security Settings
1.
On the Wireless LAN group, select Security Settings.
2.
Select an appropriate encryption mode to improve the security and privacy of your
wireless data packets.
Disable
Turn off the encryption mechanism. For the security of
your network, please select any one of the encryption mode
here.
WEP Only
Accepts only WEP clients and the encryption key should be
entered in WEP Key.
WEP/802.1x Only
Accept WEP clients with 802.1x authentication. Since the
key will be auto-negotiated during authentication, the field
of key setting below will be not available for input.
WEP or WPA/PSK
Accepts WEP and WPA clients with legal key accordingly.
Remember to select WPA type to define either Mixed or
WPA2 only in the field below.
15
WEP/802.1x or
WPA/802.1x
Accept WEP or WPA clients with 802.1x authentication.
Remember to select WPA type to define either Mixed or
WPA2 only in the field below. Since the key will be
auto-negotiated during authentication, the field of key
setting below will be not available for input.
WPA/PSK Only
Accepts WPA clients and the encryption key should be
entered in PSK. Remember to select WPA type to define
either Mixed or WPA2 only in the field below.
WPA/802.1x Only
Accept WPA clients with 802.1x authentication. Remember
to select WPA type to define either Mixed or WPA2 only in
the field below. Since the key will be auto-negotiated
during authentication, the field of key setting below will be
not available for input.
3.
For WPA encryption, type in 8~63 ASCII characters or 64 Hexadecimal digits
leading by 0x, for example "0123456789ABCD...." or "0x321253abcde....." on the
field of Pre-Shared Key (PSK). WPA encrypts each frame transmitted from the
radio using the Pre-Shared Key (PSK) which entered from this panel.
4.
As to WEP encryption, select 64-bit or 128-bit as the encryption mode. For 64bits
WEP key, type in 5 ASCII characters or 10 hexadecimal digitals leading by 0x, for
example, ABCDE or 0x4142434445. And for 128bits WEP key, type in 13 ASCII
characters or 26 hexadecimal digits leading by 0x, for example, ABCDEFGHIJKLM
or 0x4142434445464748494A4B4C4D. Only one WEP key can be selected and
allows user to type in the characters.
5.
Click OK to save settings.
Be aware that for the communication, all wireless devices must support the same
encryption bit length and share the same key. If WEP mode is selected, only one of four
preset keys can be selected at one time.
16
4. Trouble Shooting
This section will guide you to solve abnormal situations if you cannot access into the
Internet after installing the router and finishing the web configuration. Please follow
sections below to check your basic installation status stage by stage.
¾
Checking if the hardware status is OK or not.
¾
Checking if the network connection settings on your computer are OK or not.
¾
Pinging the router from your computer.
¾
Checking if the ISP settings are OK or not.
¾
Backing to factory default setting if necessary.
If all above stages are done and the router still cannot run normally, it is the time for you
to contact your dealer for advanced help.
4.1 Checking If the Hardware Status Is OK or Not
Follow the steps below to verify the hardware status.
1.
Check the power line and WLAN/LAN cable connections.
Refer to “2.1 Hardware Installation” for details.
2.
Turn on the router. Make sure the ACT LED blink once per second and the
correspondent LAN LED is bright.
3.
If not, it means that there is something wrong with the hardware status. Simply back
to “2.1 Hardware Installation” to execute the hardware installation again. And
then, try again.
4.2 Checking If the Network Connection Settings on Your
Computer Is OK or Not
Sometimes the link failure occurs due to the wrong network connection settings. After
trying the above section, if the link is stilled failed, please do the steps listed below to
make sure the network connection settings is OK.
17
For Windows
The example is based on Windows XP. As to the examples for other
operation systems, please refer to the similar steps or find support notes in
www.draytek.com.
1.
Go to Control Panel and then double-click on Network Connections.
2.
Right-click on Local Area Connection and click on Properties.
3.
Select Internet Protocol (TCP/IP) and then click Properties.
18
4.
Select Obtain an IP address automatically and Obtain DNS server address
automatically.
For MacOs
1.
Double click on the current used MacOs on the desktop.
2.
Open the Application folder and get into Network.
3.
On the Network screen, select Using DHCP from the drop down list of Configure
IPv4.
19
4.3 Pinging the Router from Your Computer
The default gateway IP address of the router is 192.168.1.1. For some reason, you might
need to use “ping” command to check the link status of the router. The most important
thing is that the computer will receive a reply from 192.168.1.1. If not, please check
the IP address of your computer. We suggest you setting the network connection as get IP
automatically. (Please refer to the section 4.2)
Please follow the steps below to ping the router correctly.
For Windows
1.
2.
Open the Command Prompt window (from Start menu> Run).
Type command (for Windows 95/98/ME) or cmd (for Windows NT/ 2000/XP). The
DOS command dialog will appear.
3.
Type ping 192.168.1.1 and press [Enter]. It the link is OK, the line of “Reply from
192.168.1.1:bytes=32 time<1ms TTL=255” will appear.
4.
If the line does not appear, please check the IP address setting of your computer.
For MacOs (Terminal)
1.
Double click on the current used MacOs on the desktop.
2.
Open the Application folder and get into Utilities.
3.
Double click Terminal. The Terminal window will appear.
4.
Type ping 192.168.1.1 and press [Enter]. It the link is OK, the line of “64 bytes
from 192.168.1.1: icmp_seq=0 ttl=255 time=xxxx ms” will appear.
20
4.4 Checking If the ISP Settings are OK or Not
Open WAN >> Internet Access page and then check whether the ISP settings are set
correctly. Click Details Page of WAN1/WAN2 to review the settings that you configured
previously.
For PPPoE Users
1.
Check if the Enable option is selected.
2.
Check if Username and Password are entered with correct values that you got from
your ISP.
21
For Static Users
1.
Check if the Enable option for Broadband Access is selected.
2.
Check if WAN IP Network Settings is set appropriately.
3.
Check if IP Address, Subnet Mask and Gateway are set correctly (must identify
with the values from your ISP) if you choose Specify an IP address.
For PPTP Users
1.
Check if the Enable option for PPTP Link is selected.
2.
Check if PPTP Server, Username, Password and WAN IP address are set
correctly (must identify with the values from your ISP).
22
4.5 Backing to Factory Default Setting If Necessary
Sometimes, a wrong connection can be improved by returning to the default settings. Try
to reset the router by software or hardware.
Warning: After pressing factory default setting, you will loose all settings
you did before. Make sure you have recorded all useful settings before you
pressing. The password of factory default is null.
Software Reset
You can reset the router to factory default via Web page.
Go to System Maintenance and choose Reboot System on the web page. The following
screen will appear. Choose Using factory default configuration and click OK. After few
seconds, the router will return all the settings to the factory settings.
Hardware Reset
While the router is running (ACT LED blinking), press the RST button and hold for more
than 5 seconds. When you see the ACT LED blinks rapidly, please release the button.
Then, the router will restart with the default configuration.
After restore the factory default setting, you can configure the settings for the router again
to fit your personal request.
23
4.6 Contacting Your Dealer
If the router still cannot work correctly after trying many efforts, please contact your
dealer for further help right away. For any questions, please feel free to send e-mail to
[email protected]
24
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement