Torment 2WD SCT Manual English
®
torment
™
ECX03033T1|ECX03026AU|ECX03033IT1
ECX03033T2|ECX03027AU|ECX03033IT2
Instruction Manual
Bedienungsanleitung
Manuel d’utilisation
MANUALE di istruzioni
1/10 Electric
short course Truck
Congratulations on your purchase of the ECX®
Torment™ Short Course Truck. This 1/10-scale
model introduces you to the sport of RC driving.
Herzlichen Glückwunsch zum Kauf des ECX
Torment Short Course Truck. Dieses 1/10 Scale
Model öffnet Ihnen die Welt des RC Car Sports.
Nous vous félicitons pour l’achat de l' ECX
Torment Short Course Truck. Ce modèle 1/10
vous initie à la conduite RC.
Congratulazioni per l’acquisto di questo Torment
Short Course Truck ECX. Questa vettura in scala
1/10 vi introdurrà nel mondo dei modelli RC.
EN
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For
up-to-date product literature, visit http://www.horizonhobby.com and click on the support tab for this product.
Meaning of Special Language:
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility
of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious
injury OR create a high probability of superficial injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.
Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some basic
mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product
or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible
components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains
instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual,
prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
Safety Precautions and Warnings
As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or
result in damage to the product or property of others.
This model is controlled by a radio signal subject to interference
from many sources outside your control. This interference can
cause momentary loss of control, so it is advisable to always
keep a safe distance in all directions around your model as this
margin will help avoid collisions or injury.
• Never operate your model with low transmitter batteries.
• Always operate your model in open spaces away from
full-size vehicles, traffic and people.
• Never operate the model in the street or in populated areas
for any reason.
• Carefully follow the directions and warnings for this and any
optional support equipment (chargers, rechargeable battery
packs, etc.) you use.
• Keep all chemicals, small parts and anything electrical out of
the reach of children.
• Never lick or place any portion of the model in your mouth as
it could cause serious injury or even death.
• Exercise caution when using tools and sharp instruments.
• Take care during maintenance as some parts may have sharp
edges.
• Immediately after using your model, do NOT touch equipment
such as the motor, electronic speed control and battery,
because they generate high temperatures. You may burn
yourself seriously touching them.
• Do not put fingers or any objects inside rotating and moving
parts, as this may cause damage or serious injury.
• Always turn on your transmitter before you turn on the
receiver in the car. Always turn off the receiver before turning
your transmitter off.
• Keep the wheels of the model off the ground when checking
the operation of the radio equipment.
table of contents
Safety Precautions and Warnings.....................................2
Water-Resistant Vehicle
with Waterproof Electronics........................................3
Specifications.................................................................3
Components.....................................................................4
Vehicle Preparations.....................................................4
Charging the Vehicle Battery.............................................4
Initial Charge......................................................................4
Charging Warnings............................................................4
Installing Transmitter Batteries.........................................5
Transmitter Battery Safety Precautions.............................5
Removing the Vehicle Body...............................................5
Installing the Battery in the Vehicle..................................5
Transmitter controls...........................................................6
RF Mode.............................................................................6
Getting Started..................................................................7
Installing the Vehicle Body................................................7
Operation.........................................................................8
When you are Finished..................................................8
Motor Care.......................................................................8
Maintenance...................................................................9
Setting the Gear Mesh......................................................9
Electronic Speed Control (ESC)..........................................9
Electrical Layout.................................................................9
Shock Cleaning..................................................................10
Fasteners............................................................................10
Binding...............................................................................11
Troubleshooting Guide.......................................................11
Limited Warranty............................................................12
Contact Information...........................................................12
FCC Information..............................................................13
IC Information..................................................................13
Compliance Information for the European Union............... 13
Parts Diagrams......................................................................... 50
Parts Lists...........................................................................52
2
Torment
™
EN
Water-resistant Vehicle with Waterproof Electronics
Your new Horizon Hobby vehicle has been designed and built with
a combination of waterproof and water-resistant components to allow you to operate the product in many “wet conditions,” including
puddles, creeks, wet grass, snow and even rain.
While the entire vehicle is highly water-resistant, it is not
completely waterproof and your vehicle should NOT be treated
like a submarine. The various electronic components used in the
vehicle, such as the Electronic Speed Control (ESC) and servo(s)
are waterproof, however, most of the mechanical components are
water-resistant and should not be submerged.
Metal parts, including the bearings, hinge pins, screws and nuts,
as well as the contacts in the electrical cables, will be susceptible
to corrosion if additional maintenance is not performed after running in wet conditions. To maximize the long-term performance
of your vehicle and to keep the warranty intact, the procedures
described in the “Wet Conditions Maintenance” section below
must be performed regularly if you choose to run in wet conditions.
If you are not willing to perform the additional care and maintenance required, then you should not operate the vehicle in those
conditions.
CAUTION: Failure to exercise caution while using this
product and complying with the following precautions
could result in product malfunction and/or void the warranty.
General Precautions
• Read through the wet conditions maintenance procedures and
make sure that you have all the tools you will need to properly
maintain your vehicle.
• Not all batteries can be used in wet conditions. Consult the
battery manufacturer before use. Do not use Li-Po batteries in
wet conditions.
• The included transmitter is not waterproof or water-resistant. If
using a different transmitter than the one included, consult your
transmitter's manual or the manufacturer before operation.
• Never operate your transmitter or vehicle where lightning may
be present.
• Do not operate your vehicle where it could come in contact
with salt water (ocean water or water on salt-covered roads),
contaminated or polluted water. Salt water is very conductive
and highly corrosive, so use caution.
• Even minimal water contact can reduce the life of your motor if
it has not been certified as water-resistant or waterproof. If the
motor becomes excessively wet, apply very light throttle until
the water is mostly removed from the motor. Running a wet
motor at high speeds may rapidly damage the motor.
• Driving in wet conditions can reduce the life of the motor.
The additional resistance of operating in water causes excess
strain. Alter the gear ratio by using a smaller pinion or larger
spur gear. This will increase torque (and motor life) when
running in mud, deeper puddles, or any wet conditions that will
increase the load on the motor for an extended period of time.
Wet Conditions Maintenance
• Remove the battery pack(s) and dry the contacts. If you have an
air compressor or a can of compressed air, blow out any water
that may be inside the recessed connector housing.
• Remove the tires/wheels from the vehicle and gently rinse the
mud and dirt off with a garden hose. Avoid rinsing the bearings
and transmission.
NOTICE: Never use a pressure washer to clean your vehicle.
• Use an air compressor or a can of compressed air to dry the
vehicle and help remove any water that may have gotten into
small crevices or corners.
• Spray the bearings, drive train, fasteners and other metal parts
with a water-displacing light oil or lubricant. Do not spray the
motor.
• Let the vehicle air dry before you store it. Water (and oil) may
continue to drip for a few hours.
• Increase the frequency of disassembly, inspection and
lubrication of the following:
• Front and rear axle hub assembly bearings.
• All transmission cases, gears and differentials.
• Motor—clean with an aerosol motor cleaner and re-oil the
bushings with lightweight motor oil.
Specifications
Transmitter
Frequency2.4GHz
Modulation
DSMR, DSM2
Battery
AA x 4
Servo
Power Supply
Output Torque
Operating Speed
Size
4.8V~6V (shared with receiver)
41.66 oz (3 kg-cm)
0.23sec/60 degrees of travel
55.6 x 18 x 30mm
Electronic Speed Control (ESC)
Input Voltage
Electric Capacity (FET)
Electric Capacity (FET)
PWM Frequency
BEC Voltage
Size
Weight
6.0–8.4 V
Forward 40A/180A
Reverse 20A/90A
1kHz
5V/2A
46.5 x 34 x 28.5mm
65 g
torment
™
3
EN
Components
3
1.ECX® Torment™ 1/10-scale Short Course Truck
2.Spektrum™ DX2E Transmitter
3. AA (4) Batteries
4.200mA Peak Battery Charger
5.Dynamite® Speedpack™ 7.2V
Ni-MH battery (DYN1050EC)
4
2
1
5
Vehicle Preparations
Charging the vehicle Battery
1. Connect the battery pack to the charger.
2. Connect the charger to an AC power source.
3. Allow the battery pack to charge for 9 hours.
CAUTION: If at any time during the charge process the
battery pack(s) becomes hot to the touch, unplug the
battery immediately and discontinue the charge process.
The vehicle battery charger produces 200 milliAmps per hour. Divide
the mAh capacity on the label of a battery by 200 to know how long
battery charging will require. For example, a fully discharged 1800mAh
battery requires 9 hours to charge.
Initial charge
Your Dynamite peak voltage detection charger includes safety circuitry and programming allowing the charger to stop charging after 15
minutes, if it senses any issues that have come up in charging. The
high electrical resistance commonly found in new, unconditioned,
Ni-MH batteries can cause this safety circuit to activate turning the
charger off before a full charging cycle is complete. This is commonly
known as a “false peak” in your battery charge.
Should this occur during your first charge cycle, it does not necessarily indicate a failure of either your charger or battery. Instead it
shows that the charger is functioning properly and that the battery is
not yet fully conditioned.
To complete your first full charging cycle in the event of a false peak,
restart the charger by pressing the Start button again. Repeat this
process until the charge cycle continues to charge past 15 minutes. It
may take as many as 2 to 4 restarts to complete your first one or two
full charge cycles. Once your charger completes a charge cycle longer
than 15 minutes, your battery will be fully charged. A typical first full
charge cycle should run for 9 hours, depending on the self-discharge
condition of the battery since it was shipped from the factory.
Once your battery is properly conditioned through a few full charge and
discharge cycles, you will see normal operation of the charger and a 9
hour charge cycle.
4
Torment
™
CHARGING WARNINGS
WARNING: Failure to exercise caution while using this
product and comply with the following warnings could result
in product malfunction, electrical issues, excessive heat, FIRE, and
ultimately injury and property damage.
• Read all safety precautions and literature prior to use of this
product.
• Never leave the battery and charger unattended during use.
• Never allow children under 14 years of age to charge battery
packs.
• Never attempt to charge dead or damaged batteries.
• Never charge a battery if the cable has been pinched or shorted.
• Never allow batteries or charger to come into contact with
moisture at any time.
• Never charge batteries in extremely hot or cold places
(recommended between 50–80°F (10–26°C)) or place in direct
sunlight.
• Always use only Ni-MH rechargeable batteries. This charger
cannot charge batteries such as “heavy duty”, “alkaline”,
“mercury” or “lithium” battery.
• Always connect to the charger correctly.
• Always disconnect the battery and charger after charging and let
them cool between charges.
• Always inspect the battery before charging.
• Always terminate all processes and contact Horizon Hobby if the
product malfunctions.
• Always make sure you know the specifications of the battery to
be charged or discharged to ensure it meets the requirements of
this charger.
• Always constantly monitor the temperature of the battery pack
while charging.
• Always end the charging process if the charger or battery
becomes hot to the touch or starts to change form during the
charge process.
• Always charge in a well ventilated area.
EN
Installing Transmitter Batteries
We recommend using only alkaline AA batteries in the
transmitter, however, it is possible to use rechargeable NiMH
batteries.
CAUTION: If using rechargeable batteries, charge only
rechargeable batteries. Charging non-rechargeable
batteries may cause the batteries to burst, resulting in injury to
persons and/or damage to property.
1. Slide the panel open on the bottom of the transmitter.
2. Obey the battery plus (+) and minus (-) diagram in the
transmitter to install 4 AA batteries.
3. Slide the panel closed.
Transmitter Battery safety precautions
• Never install damaged batteries.
• Never install batteries of mixed types or of different ages in
the transmitter.
• Always remove exhausted batteries.
• Always remove batteries before storing the transmitter.
• Low battery power can result in loss of control of the RC
vehicle.
removing THE VEHICLE BODY
INSTALLING THE BATTERY IN THE VEHICLE
1.Turn the battery clips (A) clockwise to remove the battery strap (B).
2.Install a fully charged battery.
3. Install the battery strap.
4.Turn the battery clips counterclockwise to secure the battery strap.
If desired, you can put foam blocks (ECX2015) in front of the battery
so the weight of the battery increases rear traction or in back of the
battery to increase steering response.
B
A
torment
™
5
EN
Transmitter Controls
Reverse Switch
Allows you to change the
direction of steering (ST. REV)
and throttle (TH. REV) controls
(default settings are “N” for
steering and “N” for throttle).
STeering rate
Steering Trim
Adjusts the amount the
front wheels move when the
steering wheel is turned left
or right.
Adjust to make the vehicle
drive straight with no input
at the steering wheel.
Steering Wheel
Throttle Trim
Adjusts the neutral point
of the electronic speed
control.
Control steering. Right and
Left steering with ST. REV
Switch on N
(see ST. REV switch).
Power Switch
Power on
or off the
transmitter.
Throttle Trigger
Battery Level
Indicator
Solid Green: Battery
voltage is good (above
4V).
Forward
Stop
(when TH.
REV switch on N).
Flashing Green: Battery
voltage is critically low
(below 4V). Replace
batteries.
Reverse
(when TH.
REV switch
on N).
Controls power to motor for forward
or reverse (see TH. REV switch).
Changing the Travel Adjust Settings
The travel function supports precise endpoint adjustments in
each direction for the steering and throttle channels.
1. Hold the trigger in the full brake position while powering
on the transmitter. The LED flashes rapidly, indicating the
programming mode is active.
2. Throttle End Point: Hold the trigger in the full throttle position.
Turn the TH TRIM knob to adjust the full throttle end point.
3. Brake End Point: Hold the trigger in the full brake position.
Turn the TH TRIM knob to adjust the full brake end point.
Return the trigger to the center position.
6
Torment
™
4. Left Steering End Point: Hold the steering wheel in the full left
position. Turn the ST TRIM knob to adjust the left end point.
5. Right Steering End Point: Hold the steering wheel in the full
right position. Turn the ST TRIM knob to adjust the right end
point. Return the steering wheel to the center position.
6. Power off the transmitter to save the travel adjust settings.
The minimum Travel is 75%, and the Maximum travel is
150%. The default travel settings are 125% steering and
100% throttle.
EN
Getting Started
1.Power on the transmitter.
2. Power on the ESC.
3.Do a test of the transmitter’s control of the vehicle with
the vehicle’s wheels off the ground.
4. Start driving slowly, and, if the vehicle does not go
straight, adjust the steering trim dial on the transmitter.
IMPORTANT: Seat the motor brushes by driving smoothly
on a flat surface during use of the first battery charge.
Properly seating the motor brushes will increase the life and
performance of the motor.
INSTALLING THE VEHICLE BODY
torment
™
7
EN
OperatioN
• ALWAYS turn on your transmitter before you turn on the
receiver in the vehicle. Always power off the receiver before
turning your transmitter off.
• ALWAYS operate your vehicle in a wide open area. Operating
the vehicle in a small space or indoors can cause overheating
at low speeds. Operating at low speed increases heat in the
electronic speed control (ESC). Overheating can damage the
vehicle and failure may result.
when you are finished
1.Power off the Electronic
Speed Control (ESC).
2.Disconnect the battery.
3.Power off the transmitter.
5. Recharge the battery.
4.Remove the battery from the vehicle.
Motor care
• Seat the motor brushes by driving smoothly on a flat surface
during use of the first battery charge. Failing to do so can
greatly reduce motor performance and functional life.
• Prolong motor life by preventing overheating conditions.
Undue motor wear results from frequent turns, stops and
8
Torment
™
starts, pushing objects, driving in deep water and tall grass,
and driving continuously up hill.
• Over-temperature protection is installed on the ESC to
prevent circuit damage, but cannot protect the motor from
driving against heavy resistance.
EN
Maintenance
Setting the gear mesh
The gear mesh has already been set at the factory. Setting the
gear mesh is only necessary when changing motors or gears.
You must remove the vehicle’s gear cover (A) to make this
adjustment.
Proper gear mesh (how the gear teeth meet) is important to the
performance of the vehicle. When the gear mesh is too loose, the
spur gear could be damaged by the pinion gear of the motor. If
the mesh is too tight, speed could be limited and the motor and
ESC will overheat.
Set the gear mesh by following these simple steps:
1. Loosen the 2 motor screws (B).
2. Put a small piece of paper (C) between the pinion and spur
gears.
B
C
A
3. Push the gears together while tightening the motor screws.
4. Rotate the gears to remove the paper. The gearing should
move a small amount.
5. Reinstall the gear cover.
electronic Speed control (esc)
Programming: The ESC comes with two jumpers pre-installed in
the REV: ON and BATT: Ni-MH configurations.
To disable reverse or change battery type to Li-Po, disconnect the
jumper from the default port and connect it to the desired port.
Power off the ESC, then power it back on.
If the jumpers are lost or not installed, the ESC will default to
REV: ON and BATT: Li-Po.
Operation
LED Status
Stop
Forward
Forward (full speed)
Reverse
Brake
Brake (full brake)
Ni-MH/Ni-Cd Battery
2S Li-Po Battery
ESC Ready
Battery Low Voltage
Overheat
OFF
Blinks
Solid
Blinks
Blinks
Solid
Blinks
Blinks
A
Description
A
DYN1172
Motor B
DYN1050EC
Battery 7.2V
C
SPMS603
Waterproof Steering
Servo
D
SPMSR310
Receiver
E
DYNS2211
Waterproof Electronic
Speed Control (ESC)
F
Channel 1
G
Channel 2
Sound at Power UP
1 Short Beep
2 Short Beeps
1 Long Beep
electrical layout
Part #
LED
E
B
EC3
C
EC3
D
G
For correct operation, Channels 1 and 2
must be used as shown in the wiring diagram.
The motor can be disconnected from the ESC
at the connectors in the wiring.
F
torment
™
9
EN
Rear Shock
Rear
shock
Shock Cleaning
Oil-filled shocks will require regular maintenance due to the
oil breaking down or getting dirty. This maintenance should be
performed after about every 3 to 5 hours of use, depending on
the conditions that the vehicle is used in.
• Remove the shock from the vehicle.
• Remove the cap from the shock body and dispose of fluid.
• Disassemble the shock. Clean thoroughly with DYN5505. Dry
parts before assembly.
• Re-assemble the shock and refill the shock body with silicone
fluid (30 weight recommended).
• Slowly move the shaft and piston up and down to remove air
bubbles.
• Move the piston to the midway point of the body and install
the cap.
• Wipe off any overflowing fluid.
• When properly filled, the piston should rebound about 3/8 in
(9.5mm) after being pushed in fully.
• Re-install the shock on the vehicle.
ECX1037
ECX1037
ECX1043
ECX1043
ECX1057
ECX1037
ECX1038
ECX1036
ECX1038
ECX1043
ECX1037
ECX1043
ECX1037
ECX1040
ECX1039
ECX1041
ECX1042
ECX1038
ECX1038
ECX1037
ECX1037
Part #
ECX1036
ECX1037
ECX1038
ECX1039
ECX1040
ECX1041
ECX1042
ECX1043
ECX1057
ECX1038
ECX1036
ECX1038
Ride Height Adjustment
Ride height is an adjustment that affects the way the vehicle
jumps, turns and goes over bumps. Drop one end of the
vehicle from approximately 6 inches (152 mm) in height onto
a flat surface. When dropping the front of the vehicle, after
the vehicle settles, make sure the front arms are equal and
parallel to the flat surface. Do the same with the rear to make
sure both arms are parallel with the flat surface.
Lowering the front ride height increases steering, but
decreases traction. Lowering the rear ride height increases
traction, but decreases steering.
Front Shock
front shock
Description
Shock Body Set Shock Caps, Pistons Shock Parts Set Front Shock Shaft (2) Rear Shock Shaft (2) Front Shock Springs (2) Rear Shock Springs (2) Shock O-Ring Set Fasteners
No.
Description
No.
Description
TAPPING
BINDER HEAD
M3x10mm
TAPPING
BINDER HEAD
M3x12mm
TAPPING
BINDER HEAD
M3x16mm
TAPPING
BINDER HEAD
M3x18mm
TAPPING
FLAT HEAD
M3x10mm
TAPPING
FLAT HEAD
M3x12mm
TAPPING
FLAT HEAD
M3x15mm
10
Torment
Description
No.
Description
TAPPING
FLAT HEAD
M2x16mm
STEP SCREW
M3x0.5x7.4mm
WASHER
5x7x0.5mm
BINDER
HEAD
M3x8mm
STEP SCREW
M3x0.5x13.4mm
WASHER
3x8x0.5mm
BINDER
HEAD
M3x12mm
STEP SCREW
M3x0.5x10.5mm
WASHER
2x7x0.5mm
BINDER
HEAD
M3x20mm
SETSCREW
M3x3mm
FLANGED
LOCK NUT M4
BINDER
HEAD
M3x25mm
SETSCREW
M3x12mm
LOCK NUT M3
BUTTON
HEX
M2.5x4mm
SET SHAFT
SCREW
M3x13mm
E-CLIP E2.5
BUTTON
HEX
M2.5x8mm
™
No.
LOCK WASHER
EN
Binding
Binding is the process of programming the receiver to recognize
the GUID (Globally Unique Identifier) code of a single specific
transmitter. The DX2E and SR310 are bound at the factory. If you
need to rebind, follow the instructions below.
1.With the receiver off, insert the bind plug into the BIND port
on the receiver.
2. Power the receiver through any other port. The orange LED
will flash continuously, indicating the receiver is in bind mode.
3. With the steering wheel and throttle trigger in the failsafe
positions, normally full brakes and straight steering (see the
Failsafe section on this page for more information), press and
hold the bind button and turn on the transmitter. The green
LED on the front of the transmitter will flash within three
seconds, indicating the transmitter is in bind mode.
4.Release the bind button when the green LED flashes.
Continue to hold the steering wheel and throttle trigger in the
failsafe positions until the LED on the receiver glows solid.
Bind Button
5.The LED on the receiver will glow solid when the transmitter
and receiver are bound.
6.Remove the bind plug and store it in a convenient place.
You must rebind when:
• Different failsafe positions are desired e.g., when throttle or
steering reversing has been changed.
• Changing receiver types e.g., changing from a DSMR™
receiver to a DSM2® receiver.
• Binding the receiver to a different transmitter.
Failsafe
In the unlikely event that the radio link is lost during use, the
receiver will drive the servos to their preprogrammed failsafe
positions (normally full brakes and straight steering). If the receiver
is turned on prior to turning on the transmitter, the receiver will
enter failsafe mode, driving the servos to their preset failsafe
positions. When the transmitter is turned on, normal control is
resumed. Failsafe servo positions are set during binding (see
binding a receiver above).
Troubleshooting Guide
Problem
Short Run Time
Sluggish Action
Controls Reversed
Motor/ESC overheat
Doesn’t Operate
Poor Range
The system will not
connect
Possible Cause
• Battery damaged/not charged
• Motor dirty or brushes worn
• Motor dirty or brushes worn
• Bind in drivetrain
• Vehicle battery is not charged
• ST. REV or TH. REV
• Over-geared for the driving environment
• Transmitter batteries low
• Transmitter powered off
• ESC powered off
• Vehicle battery is not charged
• Transmitter batteries low
• Transmitter antenna is damaged or loose
• Receiver antenna damaged
• Transmitter and receiver too near each other
• Transmitter and receiver too near large
metal objects (vehicles, etc.)
• Receiver accidentally put in bind mode so
receiver is no longer bound
• Check the receiver antenna to be sure it is
not cut or damaged
The receiver goes into
failsafe mode a short
distance away from the
transmitter
The receiver quits re• Low battery voltage
sponding during operation • Loose or damaged wires or connectors
between battery and receiver
Receiver loses its bind
• Transmitter accidentally put in bind mode,
ending bind to receiver
Solution
• Check/change battery
• Check/clean/replace
• Check/clean/replace
• Clean/adjust
• Replace/recharge
• Change switch position
• Install smaller pinion
• Replace/recharge
• Power On
• Power On
• Replace/recharge
• Replace/recharge
• Check/tighten
• Check/repair/replace
• Move transmitter 8–12 feet (2.4–3.6m) from
receiver
• Move away from large metal objects (vehicles, etc.)
• Rebind transmitter and receiver
• Contact Horizon Product Support
• Make sure receiver antenna is in an antenna tube
and is above vehicle
• Completely recharge battery
• Do a check of the wires and connection between
battery and receiver. Repair or replace wires and/
or connectors
• Bind transmitter to receiver
torment
™
11
EN
limited Warranty
What this Warranty Covers - Horizon Hobby, LLC (Horizon) warrants to the original purchaser that the product purchased (the "Product") will be free from defects
in materials and workmanship at the date of purchase.
What is Not Covered - This warranty is not transferable and does not cover (i)
cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv) attempted service
by anyone other than a Horizon Hobby authorized service center, (v) Product not
purchased from an authorized Horizon dealer, or (vi) Product not compliant with
applicable technical regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER
WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL
IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE
HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy - Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace,
any Product determined by Horizon to be defective. Horizon reserves the right to
inspect any and all Product(s) involved in a warranty claim. Service or replacement
decisions are at the sole discretion of Horizon. Proof of purchase is required for all
warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability - HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER
SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT
LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the
liability of Horizon exceed the individual price of the Product on which liability is
asserted. As Horizon has no control over use, setup, final assembly, modification
or misuse, no liability shall be assumed nor accepted for any resulting damage or
injury. By the act of use, setup or assembly, the user accepts all resulting liability.
If you as the purchaser or user are not prepared to accept the liability associated
with the use of the Product, purchaser is advised to return the Product immediately
in new and unused condition to the place of purchase.
Law - These terms are governed by Illinois law (without regard to conflict of law
principals). This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state. Horizon reserves the right to change or
modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services - Your local hobby store and/or place of
purchase cannot provide warranty support or service. Once assembly, setup or use
of the Product has been started, you must contact your local distributor or Horizon
directly. This will enable Horizon to better answer your questions and service you
in the event that you may need any assistance. For questions or assistance, please
visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or
call the toll free telephone number referenced in the Warranty and Service Contact
Information section to speak with a Product Support representative.
Inspection or Services - If this Product needs to be inspected or serviced and
is compliant in the country you live and use the Product in, please use the Horizon
Online Service Request submission process found on our website or call Horizon
to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but
are not designed to withstand the rigors of shipping without additional protection.
Ship via a carrier that provides tracking and insurance for lost or damaged parcels,
as Horizon is not responsible for merchandise until it arrives and is accepted at
our facility. An Online Service Request is available at http://www.horizonhobby.
com/content/_service-center_render-service-center. If you do not have internet
access, please contact Horizon Product Support to obtain a RMA number along
with instructions for submitting your product for service. When calling Horizon, you
will be asked to provide your complete name, street address, email address and
phone number where you can be reached during business hours. When sending
product into Horizon, please include your RMA number, a list of the included items,
and a brief summary of the problem. A copy of your original sales receipt must
be included for warranty consideration. Be sure your name, address, and RMA
number are clearly written on the outside of the shipping carton.
NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with
a Li-Po battery, please contact the appropriate Horizon Product Support
office.
Warranty Requirements - For Warranty consideration, you must include
your original sales receipt verifying the proof-of-purchase date. Provided
warranty conditions have been met, your Product will be serviced or replaced free
of charge. Service or replacement decisions are at the sole discretion of Horizon.
Non-Warranty Service - Should your service not be covered by warranty,
service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of
the retail purchase cost. By submitting the item for service you are agreeing to
payment of the service without notification. Service estimates are available upon
request. You must include this request with your item submitted for service. Nonwarranty service estimates will be billed a minimum of ½ hour of labor. In addition
you will be billed for return freight. Horizon accepts money orders and cashier’s
checks, as well as Visa, MasterCard, American Express, and Discover cards. By
submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and
Conditions found on our website http://www.horizonhobby.com/content/_servicecenter_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not
be serviced. Further, the sender will be responsible for arranging return
shipment of the un-serviced Product, through a carrier of the sender’s
choice and at the sender’s expense. Horizon will hold non-compliant
Product for a period of 60 days from notification, after which it will be
discarded.
contact Information
Country of Purchase
Horizon Hobby
Horizon Service Center
(Repairs and Repair Requests)
Horizon Product Support
United States of America (Product Technical Assistance)
Sales
United Kingdom
12
Service/Parts/Sales:
Horizon Hobby Limited
Torment
™
Contact Information
servicecenter.horizonhobby.com/
RequestForm/
www.quickbase.com/db/
bghj7ey8c?a=GenNewRecord
888-959-2306
sales@horizonhobby.com
888-959-2306
sales@horizonhobby.co.uk
+44 (0) 1279 641 097
Address
4105 Fieldstone Rd
Champaign, Illinois, 61822 USA
Units 1–4 , Ployters Rd, Staple Tye
Harlow, Essex, CM18 7NS, United
Kingdom
EN
Country of Purchase
Germany
Horizon Hobby
Horizon Technischer Service
Sales: Horizon Hobby GmbH
France
Service/Parts/Sales:
Horizon Hobby SAS
China
Service/Parts/Sales:
Horizon Hobby – China
Contact Information
service@horizonhobby.de
+49 (0) 4121 2655 100
infofrance@horizonhobby.com
+33 (0) 1 60 18 34 90
info@horizonhobby.com.cn
+86 (021) 5180 9868
Address
Christian-Junge-Straße 1
25337 Elmshorn, Germany
11 Rue Georges Charpak
77127 Lieusaint, France
Room 506, No. 97 Changshou Rd.
Shanghai, China 200060
FCC Information
IC Information
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by
the party responsible for compliance could void the user’s
authority to operate the equipment.
This product contains a radio transmitter with wireless technology
which has been tested and found to be compliant with the applicable
regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz
frequency range.
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Antenna Separation Distance
When operating your Spektrum transmitter, please be sure to maintain
a separation distance of at least 5 cm between your body (excluding
fingers, hands, wrists, ankles and feet) and the antenna to meet RF
exposure safety requirements as determined by FCC regulations.
The following illustrations show the approximate 5 cm RF exposure area
and typical hand placement when operating your Spektrum transmitter.
Compliance Information for the European Union
Declaration of Conformity
(in accordance with ISO/IEC 17050-1)
No. HH2014121009
Product(s):Torment 1:10 Silver/Blue RTR; Torment 1:10 Black/Green
RTR (Spektrum DX2E Transmitter and SR310 Receiver
included)
Item Number(s): ECX03033IT1, ECX03033IT2
Equipment class: 1
The object of declaration described above is in conformity with the
requirements of the specifications listed below, following the provisions
of the European R&TTE directive 1999/5/EC, EMC Directive 2004/108/
EC and LVD Directive 2006/95/EC:
EN 300-328 V1.8.1
EN 301 489-1 V1.9.2: 2012
EN 301 489-17 V2.1.1: 2009
EN 60950-1:2006+A11:2009+A1:2010+A12: 2011
EN 62311: 2008
EN 55022:2010 + AC:2011
EN 55024:2010
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2008
Signed for and on behalf of:
Horizon Hobby, LLC
Champaign, IL USA
12.10.2014
Instructions for disposal of WEEE
by users in the European Union
This product must not be disposed of with other waste. Instead, it is the
user’s responsibility to dispose of their waste equipment by handing it
over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling
of your waste equipment at the time of disposal will help to conserve
natural resources and ensure that it is recycled in a manner that protects
human health and the environment. For more information about where
you can drop off your waste equipment for recycling, please contact
your local city office, your household waste disposal service or where
you purchased the product.
Mike Dunne
Executive Vice President Product Divisions, Horizon Hobby, LLC
torment
™
13
Parts Diagram | explosionszeichnung | vue éclatée des PiÈces |
esploso del modello con referenza pezzi
Recommended Items
Empfohlene Werkzeuge
Outils Recommandés
Attrezzi CONSIGLIATI
M3X10
11
10
30
M3X10
12
M3X10
9
M3X12
45
51 M3X12
1
2 mm
1.5 mm
3
M3X12
51
M3X12
M3X25
12
M3X18
M3X10
M3X12
2
M3X12
4
7
2
44
20
7
2
45
49
M3X10
8
17
2
2
19
2
7
16
19
20
M3X15
20
M3X15
M3X12
M3X10
M3X25
13
46
M3X12
19
Torment
™
7
18
23
M3X15
8
M3X12
21
14
15
15
31
M3X10
8
29
23
31
M3X8
52
5
M3X18
13
22
PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES |
ESPLOSO DEL MODELLO CON REFERENZA PEZZI
The slipper clutch can be adjusted using
this locknut (ECX1060). Fully tighten the
locknut, then loosen the nut two full
turns.
42
M3X3
M2.5X4
Die Rutschkupplung kann durch diese
Stopmutter eingestellt werden (ECX1060).
Ziehen Sie die Mutter an und drehen Sie
dann volle zwei Umdrehungen zurück.
M2.5X8 32
32
41
22 34 34
34
34
32
15
M2.5X8
33 48
Il est possible d’ajuster le sliper par action sur cet écrou de blocage (ECX1060).
Veillez à serrer l’écrou de blocage à fond.
Ensuite, devissez l’écrou de trois tours
complets.
15
6
48
35 15 33 15
39
25
36
38 35 33
M3X18
36
M2X16
33
35
La frizione può essere regolata con
questo dado autobloccante (ECX1060).
Prima avvitate completamente il dado,
poi svitatelo 2 giri.
40 33
15
36
M3X12
39
33
33
35
33 35 33
M2X16
38
25
M3X12
43
M3X15
44
M3X15
45
17
M3X12
52
M3X10
M3X10
43
50
M3X12
47
25
M3X12
M3X18
M3X12
M3X12
47
M3X12
M3X10
52
25
M3X20
47
11
M3X12
M3X10
26
29
13
19
24
M3X15
20
3
29
32
39
49
27
32
M3X12
26
19
13
23
20
28
20
M3X12
M3X12
When installing the wheel, make sure the drive hex is aligned with the drive pin. When
the drive hex is removed, the drive pin can fall out of the axle.
Bitte achten Sie bei der Radmontage darauf, dass die Radachse im Radmitnehmer
sitzt und dass der der Querstift nicht heraus fällt.
Lors de l’installation de la roue, assurez-vous que l'hexagone de roue est aligné avec la goupille
d'entraînement. En cas de démontage de l'hexagone, la goupille peut sortir de l'axe et tomber.
Quando montate le ruote, accertatevi che il trascinatore esagonale sia allineato con la spina
del mozzo ruota. Quando togliete il trascinatore esagonale la spina può sfilarsi dal mozzo.
26
21
27
13
15
15
14
13
22
torment
™
53
Replacement Parts / Ersatzteile / Pièces de rechange / Pezzi di ricambio
Part # | Nummer
Description
Numéro | Codice
Beschreibung
Descrizione
Châssis principal
Sauve servo
Rondelle (6)
Jeu de vis épaulées (8)
Récepteur DSM 3 voies
étanche
Telaio principale
Set salvaservo
Copertura e set montaggio
posteriore
Grani M3x12 (4)
Spugna distanziale
batteria
Viti per il motore/ set di
rondelle
Sfere Uniball (6)
Set viti a doppio stadio (8)
Ricevitore Sport (con
rivestimento protettivo)
Servo digital standard
surface, étanche
Servo standard digitale
car, WP
Fixation pour batterie
Jeu de pare-chocs avant
Jeu de renfort de
suspension
Piastra fermabatteria
Set paraurti ant
1
2
ECX2008
ECX1028
3
ECX2011
4
ECX1050
Chassis
Servo Saver Set
und hinterer
Cover and Rear Mount Set Abdeckung
Halter Set
Setscrew M3x12 (4) Schrauben Set M3x12 (4)
5
ECX2015
Foam Block
Schaum Block
Bloc de mousse
6
ECX1098
Motor Screw/Washer Set
Vis Moteur/Set Rondelles
7
8
ECX1058
ECX1065
9
SPMSR310
Ball Stud (6)
Shoulder Screw Set (8)
3-Ch DSM Sport Receiver
(Coated)
Set Motorschrauben/
Unterlegscheiben
Kugelkopf (6)
Passschrauben Set (8)
3 Kanal DSM Sport
Empfänger (beschichtet)
Standard Digital Surface
Servo Spritzwassergeschützt
Akkuhalter
Vordere Stossstange
10 SPMSS6170
11 ECX231003
12 ECX4005
Main Chassis Servo Saver Set Description
Standard Digital Surface
Servo, WP
13 ECX2006
Battery Hold Down
Front Bumper Set
Suspension Arm Mount
Set
14 ECX4003
Mounted Wheel/Tire (2)
Rad montiert (2)
15 ECX1015
Wheel Bearing Set Radlagersatz Set
16 ECX1018
Front Suspension Arm Set Querlenker Set vorne
17 ECX1020
Shock Tower Set Dämpferbrücke
18 ECX1035
19 ECX1044
Front Axle (2) Hinge Pin Set Radachse vorne (2)
Querlenkerbolzen Set
20 ECX1046
Camber, Toe Link Set Spur- Sturzstangenset
21 ECX1049
Wheel Pins (4) Radmitnehmerstifte (4)
22 ECX1060
M4 Locknut (4)
M4 Stopmutter (4)
23 ECX234000
Steering Block, Rear Hub
Set
Lenk- und Rädträger
hinten
24 ECX1019
Rear Suspension Arm Set Querlenker Set hinten
25 ECX1021
Transmission Case Set Getriebegehäuse
26 ECX232000
27 ECX232005
Driveshafts (2)
Driveshaft Pivot Ball (4) Querlenker Set hinten
32 ECX1027
Antriebswellen (2)
Antriebswellengelenk (4)
Wellenmitnehmer hinten
Rear Axle (2)
(2)
Querlenkerbolzen
Hinge Pin Screws (8) Schrauben (8)
60A Vorwärts/Rückwärts
60A FWD/REV Brushed ESC
Bürstenregler
Stoßdmämpferkappen
Shock Caps, Pistons
Kolben
Gear Cover
Getriebeabdeckung
33 ECX1022
Transmission Gear Set 34 ECX1024
Slipper Clutch Plates, Pads, Rutschkupplung Teilesatz
Spring 35 ECX1025
Transmission Idler Shaft,
Drive Pins 28 ECX232001
29 ECX1045
30 DYNS2210
31 ECX1037
54
Torment
™
Getriebe
Hauptgetriebewelle Set
Capot et fixations arrières
Jeu de vis M3x12 (4)
Supporti braccetti sosp.
Ruote e gomme montate
(2)
Jeu de roulement de roue Set cuscinetti ruote
Jeu de bras de suspension Braccetti delle sospensioni
avant
anteriori
Jeu de support
Supporto ammortizzatori
d’amortisseur
posteriori
Axe de roue avant (2)
Mozzi ruota anteriori (2)
Jeu d'axes de suspension Set perni sospensioni
Jeu de biellettes
Set tiranteria Camber e
de carrossage et de
convergenza
pincement
Pneu monté /jante (2)
Goupilles d'entraînement
(4)
Ecrous de roues M4 (4)
Jeu de fusées avant et
arrière avec étriers portes
fusées avant
Jeu de bras de suspension
arrière
Ensemble carter de
transmission
Cardan (2)
Croisillon de cardan (4)
Spine trascinatori ruote (4)
Dadi autobloccanti M4 (4)
Set blocco sterzo, mozzo
posteriore
Braccetti delle sospensioni
posteriori
Set scatola trasmissione
Semiasse (2)
Snodi semiassi (4)
Attacco a sfera semiasse
Axe de roue arrière
(4)
Vis de fixation de renfort
Viti per perni sospensioni
(8)
(8)
Variateur 60A Marche Av/Arr 60A FWD/REV regolatore a
pour moteur brushed
spazzole
Bouchon, piston et rotules Set tappi e pistoni
d’amortisseur
ammortizzatori
Carter de Réducteur
Copertura per ingranaggi
Couronne et pignons
Set
ingranaggi
intermédiaires,corps et
trasmissione
pignons de différentiel
Garnitures, plateaux et
ressort de slipper
Arbre secondaire de transmission avec goupilles
d'entraînement
Piattelli frizione, disco,
molla
Alberino intermedio con
spina
Part # | Nummer
Description
Numéro | Codice
Beschreibung
36 ECX1026
Transmission Drive Shaft (2) Getreibeausgangswelle (2)
37
38
39
40
41
42
43
Washer Set
Bearings 10x15x4 (2)
M3 Locknut (4)
Spur Gear
19-Tooth Pinion Gear
Motor
Body Clip
Unterlegscheiben Set
Lager 10x15x4 (2)
M3 Stopmutter (4)
Hauptzahnrad
Ritzel 19 Zähne
Motor
Body Clip
44 ECX2010
Body Post Set
Karosseriehalterset
45 ECX2009
Aufnahme
Karosseriehalter
Skid Plate Set
Unterfahrschutz Set
Rear Holder Set
Set Halter hinten
Top Shaft/Spacer
Getriebewelle oben
Setscrew M3x10
Sicherungsschrauben (4)
Rear Bumper Set
Hinterer Stoßfänger Set
Nerf Bar Set
Seitenaufprallschutz
Mud Flap Set
Schmutzfängerset
ECX
Karosserie
Body, Silver/Blue: Torment SilberTorment
/ Blau
Body, Black/Green:
ECX Torment Karosserie
Torment
Schwarz/ Grün
DX2E 2-Channel DSM
DX2E 2-Kanal DSM
Surface Radio
Fernsteuerung
46
47
48
49
50
51
52
ECX1052
ECX1055
ECX1059
ECX1076
ECX1073
DYN1172
ECX1048
ECX2007
ECX2013
ECX1023
ECX1033
ECX4006
ECX4004
ECX4007
ECX230006
ECX230007
SPM2322
Body Mount Set
DYNC2000CA
Prophet™ Sport Ni-MH 35W Prophet Sport 35W Peak
AC Charger
Ni-MH Ladegerät
DYN1050EC
Ni-MH battery
Ni-MH akku
Description
Descrizione
Axe d’arbre de
transmission (2)
Jeu de rondelles
Roulements 10x15x4 (2)
Ecrou auto-freiné M3 (4)
Couronne
Pignon 19 dents
Moteur
Clips Carrosserie
Mozzi Differenziale (2)
Set rondelle
Cuscinetti 10x15x4 (2)
Dadi autobloccanti M3 (4)
Corona
Pignone a 19 denti
Motore
Clippe per carrozzeria
Set di sostegni per la
Set Plots Carrosserie
carrozzeria
di montaggio per la
Set Montage Carrosserie Set
carrozzeria
Set Plaque Chassis
Set pistre di protezione
Set de Maintien Arrière
Set supporto posteriore
Set de Goupilles
Set di spessori
Vis (4)
Viti (4)
Set de pare-choc arrière
Set paraurti posteriore
Set de protection latérales Set protezione laterale
Set de bavettes
Set paraspruzzi
Carrosserie argent/bleue
Carrozz. Blu/Arg Torment
- Torment
Carrosserie noire/verte Carrozz. Nero/Verde
Torment
Torment
DX2E 2-canali DSM
DX2E 2 voies DSMR
radiocomando car
Prophet Sport 35W
Prophet Sport 35W CariChargeur à détection de
cabatterie a rilevamento
pics
di picchi
Batterie Ni-MH
Batteria Ni-MH
torment
™
55
®
ECX03033T1|ECX03026AU|ECX03033IT1
ECX03033T2|ECX03027AU|ECX03033IT2
www.ecxrc.com
© 2015 Horizon Hobby, LLC. ECX, the ECX logo, Torment, Prophet, Dynamite, Speedpack, DSMR, DSM2 and the Horizon Hobby logo are
trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of
Bachmann Industries, Inc.
Revised 11/2014 37873.5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising