Owner’s Manual & Safety Instructions
Save This Manual
Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures� Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number)�
Keep this manual and the receipt in a safe and dry place for future reference� reV 15d
1.5 HOrSepOWer
7" BRIDGE
TILE SAW
note: Stand and Diamond Blade sold separately�
Visit our website at: http://www.harborfreight.com
email our technical support at: [email protected]
When unpacking, make sure that the product is intact and undamaged� If any parts are missing or broken, please call 1-888-866-5797 as soon as possible�
Copyright © 2008 by Harbor Freight Tools ® � All rights reserved�
No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools�
Diagrams within this manual may not be drawn proportionally� Due to continuing improvements, actual product may differ slightly from the product described herein�
Tools required for assembly and service may not be included� read this material before using this product.
Failure to do so can result in serious injury.
SaVe tHiS ManuaL.
table of contents
Safety ��������������������������������������������������������� 3
Setup - Before Use: ������������������������������������ 8
Setup ���������������������������������������������������������� 8
Operation ��������������������������������������������������� 10
Maintenance ���������������������������������������������� 12
Parts Lists and Diagrams �������������������������� 14
Warranty ���������������������������������������������������� 20
WarninG SyMBOLS anD DeFinitiOnS
This is the safety alert symbol� It is used to alert you to potential personal injury hazards� Obey all safety messages that follow this symbol to avoid possible injury or death�
Indicates a hazardous situation which, if not avoided, will result in death or serious injury�
Indicates a hazardous situation which, if not avoided, could result in death or serious injury�
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury�
Addresses practices not related to personal injury�
Page 2 For technical questions, please call 1-888-866-5797.
Item 98265
iMpOrtant SaFety inFOrMatiOn
General tool Safety Warnings
read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
1� KEEP GUARDS IN PLACE and in working order�
2� REMOVE ADJUSTING KEYS AND
WRENCHES� Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on�
3� KEEP WORK AREA CLEAN�
Cluttered areas and benches invite accidents�
11� ALWAYS USE SAFETY GLASSES� Also use face or dust mask if cutting operation is dusty�
Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses�
12� SECURE WORK� Use clamps or a vise to hold work when practical� It’s safer than using your hand and it frees both hands to operate tool�
4� DON’T USE IN DANGEROUS ENVIRONMENT�
Don’t use power tools in damp or wet locations, or expose them to rain� Keep work area well lighted�
13� DON’T OVERREACH�
Keep proper footing and balance at all times�
5� KEEP CHILDREN AWAY� All visitors should be kept safe distance from work area�
14� MAINTAIN TOOLS WITH CARE� Keep tools sharp and clean for best and safest performance� Follow instructions for lubricating and changing accessories�
6� MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter keys�
7� DON’T FORCE TOOL� It will do the job better and safer at the rate for which it was designed�
15� DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like�
8� USE RIGHT TOOL� Don’t force tool or attachment to do a job for which it was not designed�
16� REDUCE THE RISK OF UNINTENTIONAL
STARTING� Make sure switch is in off position before plugging in� table a: recOMMenDeD MiniMuM Wire
GauGe FOr eXtenSiOn cOrDS (120 VOLt)
naMepLate aMpereS
(at full load)
0 – 6
6�1 – 10
10�1 – 12
12�1 – 16
25′ 50′ 100′ 150′
18
18
16
14
eXtenSiOn cOrD
LenGtH
16
16
16
12
16 14
14
14
12
12
Do not use.
9� USE PROPER EXTENSION CORD� Make sure your extension cord is in good condition� When using an extension cord, be sure to use one heavy enough to carry the current your product will draw�
An undersized cord will cause a drop in line voltage resulting in loss of power and overheating�
Table A shows the correct size to use depending on cord length and nameplate ampere rating�
If in doubt, use the next heavier gauge�
The smaller the gauge number, the heavier the cord�
17� USE RECOMMENDED ACCESSORIES�
Consult the owner’s manual for recommended accessories� The use of improper accessories may cause risk of injury to persons�
18� NEVER STAND ON TOOL�
Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted�
19� CHECK DAMAGED PARTS� Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function – check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation� A guard or other part that is damaged should be properly repaired or replaced�
20� DIRECTION OF FEED�
Feed work into a blade or cutter against the direction of rotation of the blade or cutter only�
21� NEVER LEAVE TOOL RUNNING UNATTENDED�
TURN POWER OFF� Don’t leave tool until it comes to a complete stop�
10� WEAR PROPER APPAREL� Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts� Nonslip footwear is recommended�
Wear protective hair covering to contain long hair�
Item 98265 For technical questions, please call 1-888-866-5797.
Page 3
Grounding instructions
tO preVent eLectric SHOcK anD DeatH FrOM incOrrect
GrOunDinG Wire cOnnectiOn reaD anD FOLLOW tHeSe inStructiOnS:
110-120 Vac Grounded tools: tools with three prong plugs
6� Repair or replace damaged or worn cord immediately�
1� In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock�
This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug� The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances�
2� Do not modify the plug provided – if it will not fit the outlet, have the proper outlet installed by a qualified electrician�
3� Improper connection of the equipment-grounding conductor can result in a risk of electric shock�
The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor�
If repair or replacement of the electric cord or plug is necessary, do not connect the equipmentgrounding conductor to a live terminal�
4� Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded�
5� Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool’s plug�
tile Saw Safety Warnings
Grounding pin
125 Vac 3-prong plug and Outlet
(for up to 125 Vac and up to 15 a)
7� This tool is intended for use on a circuit that has an outlet that looks like the one illustrated above in
125 Vac 3-prong plug and Outlet� The tool has a grounding plug that looks like the plug illustrated above in 125 Vac 3-prong plug and Outlet�
8� The outlet must be properly installed and grounded in accordance with all codes and ordinances�
9� Do not use an adapter to connect this tool to a different outlet�
For your Own Safety read instruction
Manual Before Operating Saw
1� Wear eye protection�
2� Use saw-blade guard and spreader for every operation for which it can be used, including all through sawing�
3� Keep hands out of the line of saw blade�
4� Use an appropriate push-stick when required�
5� Know how to reduce risk of kickback�
6� Do not perform any operation freehand�
7� Never reach around or over saw blade�
8� Make sure the workpiece is supported at all times while sawing�
9� To properly understand all safety warnings, be familiar with the following safety terms and equipment: a� Featherboard – A block with “fingers” that hold the workpiece against the fence while sawing� b� Through-sawing – A cut made from one side of a tile to the opposite side, without stopping� c� Freehand – Feeding a workpiece through the saw without using a fence or guided support to guide it� nOt a SaFe MetHOD.
d� Kerf – The gap made by the saw in the workpiece� e� Kickback – A sudden reaction to a pinched, bound, or misaligned blade, causing an uncontrolled workpiece to lift up and out of the saw toward the operator�
Page 4 For technical questions, please call 1-888-866-5797.
Item 98265
f� Spreader – A metal plate that follows the saw blade to keep the kerf (gap) from closing on the saw blade� Spreaders, except riving knives, must be aligned to the blade after blade adjustment to prevent binding� g� Riving Knife – A spreader mounted on the same mechanism as the blade�
Generally more effective than simple spreaders�
10� As noted previously, Kickback is a sudden reaction to a pinched, bound, or misaligned blade, causing an uncontrolled workpiece to lift up and out of the saw toward the operator�
Kickback is usually a result of tool misuse and can be limited or avoided by following the precautions below:
• Fence must be completely parallel to the saw blade�
• Workpiece must be free from flaws and from foreign objects�
11� Do not use a dull or damaged blade�
12� Maintain control of the workpiece� Do not allow the workpiece to rest against the moving blade without holding onto it�
• If the blade binds or a cut is interrupted, turn off the power switch and hold the workpiece still until the blade stops� Correct the cause of blade binding before proceeding�
• Before continuing an unfinished cut, center the blade in the pre-cut kerf and check that the saw is not engaged into the workpiece before turning on the saw�
• Push the tile past the blade prior to release�
13� Check guards for proper operation with saw disconnected from power before each use�
Do not disable any guard� Do not operate saw if any movable guard does not move freely and close instantly� Make sure any movable guard does not touch the blade in all angles, depths of cut, and positions�
14� Keep the guard in place while through-sawing�
Verify that the spreader lines up with the blade to prevent binding�
15� pOSitiOn OF tiLe SaW
1� To avoid the possibility of the tool plug or receptacle getting wet, position tile saw to one side of a wall mounted receptacle to prevent water from dripping onto the receptacle or plug�
The user should arrange a “drip loop” in the cord connecting the saw to a receptacle� The “drip loop” is that part of the cord below the level of the receptacle, or the connector if an extension cord is used, to prevent water traveling along the cord and coming in contact with the receptacle�
2� If the plug or receptacle does get wet, DON’T unplug the cord� Disconnect the fuse or circuit breaker that supplies power to the tool� Then unplug and examine for presence of water in the receptacle� eXtenSiOn cOrDS
3� Use only extension cords that are intended for outdoor use� These extension cords are identified by a marking “Acceptable for use with outdoor tools; store indoors while not in use�” Use only extension cords having an electrical rating not less than the rating of the product� Do not use damaged extension cords� Examine extension cord before using and replace if damaged� Do not abuse extension cords and do not yank on any cord to disconnect� Keep cord away from heat and sharp edges� Always disconnect the extension cord from the receptacle before disconnecting the product from the extension cord�
4� WARNING – To reduce the risk of electrocution, keep all connections dry and off the ground�
Do not touch plug with wet hands�
5� Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s) to be used for the tile saw� Receptacles are available having built-in GFCI protection and may be used for this measure of safety�
6� DO nOt Operate WitH any GuarD
DiSaBLeD, DaMaGeD, Or reMOVeD. Moving guards must move freely and close instantly.
Item 98265 For technical questions, please call 1-888-866-5797.
Page 5
7� The use of accessories or attachments not recommended by the manufacturer may result in a risk of injury to persons�
8� When servicing use only identical replacement parts�
9� Do not depress the spindle lock when starting or during operation�
10� Only use safety equipment that has been approved by an appropriate standards agency� Unapproved safety equipment may not provide adequate protection� Eye protection must be ANSI-approved and breathing protection must be NIOSH-approved for the specific hazards in the work area�
11� Stay alert, watch what you are doing and use common sense when operating a power tool�
Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication�
A moment of inattention while operating power tools may result in serious personal injury�
12� Industrial applications must follow OSHA guidelines�
13� Maintain labels and nameplates on the tool�
These carry important safety information�
If unreadable or missing, contact
Harbor Freight Tools for a replacement�
14� Avoid unintentional starting�
Prepare to begin work before turning on the tool�
15� People with pacemakers should consult their physician(s) before use� Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure�
16� WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm� Some examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement or other masonry products
• Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work� To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles�
(California Health & Safety Code § 25249�5, et seq.)
17� WARNING: The cord of this product contains lead and/or di (2-ethylhexyl) phthalate (DEHP), chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm� Wash hands after handling�
(California Health & Safety Code § 25249�5, et seq.)
18� WARNING: This product contains di (2-ethylhexyl) phthalate (DEHP), a chemical known to the State of California to cause cancer and birth defects or other reproductive harm� (California Health
& Safety Code § 25249�5, et seq.)
19� The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur�
It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator�
Vibration Safety
This tool vibrates during use� Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders�
To reduce the risk of vibration-related injury:
1� Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use� Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool� If you feel any medical or physical symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible�
2� Do not smoke during use� Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury�
3� Use tools with the lowest vibration when there is a choice between different processes�
4� Include vibration-free periods each day of work�
5� Grip workpiece as lightly as possible (while still keeping safe control of it)� Let the tool do the work�
6� To reduce vibration, maintain the tool as explained in this manual� If any abnormal vibration occurs, stop use immediately�
SaVe tHeSe inStructiOnS.
Page 6 For technical questions, please call 1-888-866-5797.
Item 98265
Specifications
Electrical Rating
Motor No Load Speed
120VAC / 60Hz / 10A
5000 RPM
Max� Accessory Diameter 7″
Arbor Size 5/8″
Tilting Head
Water Pump Max� Flow
Stand
Blade Type
45° Left-Tilt only
160 GPH
Sold separately
7″ Diamond Blade (Wet or Dry),
5/8″ arbor, continuous rim
(free of openings and grooves)
(sold separately)
235575
Item 98265 For technical questions, please call 1-888-866-5797.
Page 7
Setup - Before use:
read the entire iMpOrtant SaFety inFOrMatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
tO preVent SeriOuS inJury FrOM acciDentaL OperatiOn: turn the power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section.
note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual�
assembly
1� Attach the Handle (B13) onto the Holder (B09) turned as shown, using the two supplied
Screws (B12) and Washers (B11)� See Figure A�
Screw (B12)
Washer (B11)
2� Check that the water pump (A25) is properly installed within its holding clips� See Figure B�
Handle
(B13)
Figure a
Mounting
1� Mount the tool to a workbench or other stable surface�
Holding clips
Figure B
3� Run the water hose from the pump discharge to the Blade Cover (A30) and connect it�
2� The ideal method is to mount the tile saw on the stand made for it (sold separately)�
Page 8 For technical questions, please call 1-888-866-5797.
Item 98265
Functions
Handle power
Switch
Blade
Fence
Miter Gauge
Water tray
Slide Lock
Knob reset Button
Bevel Lock
Knob
Item 98265 For technical questions, please call 1-888-866-5797.
Page 9
Operating instructions
read the entire iMpOrtant SaFety inFOrMatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
tool Set up
tO preVent SeriOuS inJury FrOM acciDentaL OperatiOn: turn the power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section.
tO preVent SeriOuS inJury:
DO nOt Operate WitH any GuarD DiSaBLeD, DaMaGeD, Or reMOVeD.
Moving guards must move freely and close instantly.
installing a Blade
1� Disconnect the power supply�
2� Push the carriage to the open end of the water tray to the right of where the Worktables end (D06)�
3� Remove the three Screws (A28) that hold the
Clear Guard to the Blade Guard� See Figure C�
4� Put the flat wrench over the Outer Flange (A33) to keep the Blade from turning� Remove the
Arbor Bolt (A32) by turning it counterclockwise�
5� Remove the Blade (if installed) and replace with a new one. The new Blade must be 7″ in diameter with a 5/8″ arbor, free of openings and grooves, and rated to at least 5,000 RPM� Match the arrow on the Blade with the arrow on the Blade cover�
6� With the flat wrench in place again, reinstall the
Arbor Bolt, tightening it securely clockwise�
7� Replace the Clear Guard and secure with the three Screws�
Figure c
Workpiece and Work area Set up
1� Designate a work area that is clean and well-lit�
The work area must not allow access by children or pets to prevent distraction and injury�
2� Route the power cord along a safe route to reach the work area without creating a tripping hazard or exposing the power cord to possible damage� The power cord must reach the work area with enough extra length to allow free movement while working�
3� Secure loose workpieces using a vise or clamps
(not included) to prevent movement while working�
4� There must not be objects, such as utility lines, nearby that will present a hazard while working�
Page 10 For technical questions, please call 1-888-866-5797.
Item 98265
General Operating instructions
1� Make sure that the Switch is in the off-position, then plug in the tool�
2� Turn on the tool�
3� Use two hands and hold workpiece securely against table and fence at all times�
4� When making a flat cut, slide the piece to be cut up against the Fence securely� See Figure E�
5� When making an angled cut, position one end securely at the point where the two Fence halves come together� Use the Clamp Plate to secure it�
The cut-off side of the workpiece must be free to move away from the blade to prevent binding�
6� With the saw and the water pump turned on and operating, pull Handle to move blade through material at a slow and steady pace� cautiOn! Do not attempt to cut on a push stroke, the blade may grab the workpiece.
7� Beveled cuts can also be accomplished by loosening the Knobs on either side of the saw�
Tilt the Sliding Supports, and blade/motor assembly as a unit� There is a scale and indexing pointer on the Sliding Supports indicating angle of tilt� See Figure D�
Sliding Bar
Support
Bevel Scale
Knob
Figure D
8� To prevent accidents, turn off the tool and unplug the tool from its electrical outlet after use� Clean, then store the tool indoors out of children’s reach�
Item 98265
Figure e: Straight cutting
For technical questions, please call 1-888-866-5797.
Page 11
Maintenance and Servicing
procedures not specifically explained in this manual must be performed only by a qualified technician.
tO preVent SeriOuS inJury FrOM acciDentaL OperatiOn: turn the power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section.
tO preVent SeriOuS inJury FrOM tOOL FaiLure:
Do not use damaged equipment. if abnormal noise or vibration occurs, have the problem corrected before further use.
cleaning, Maintenance, and Lubrication
1� BeFOre eacH uSe, inspect the general condition of the tool� Check for:
• loose hardware,
• misalignment or binding of moving parts,
• cracked or broken parts,
• damaged electrical wiring, and
• any other condition that may affect its safe operation�
cleaning the Saw
1� With the saw turned off and the cord pulled out from the outlet, wipe down all of the external parts of the unit with a damp (not dripping wet) sponge�
2� Make sure that the Water Tray is also cleaned and a container of some type is located below the Drain
Plug (E03)� Remove the plug and drain the water and silt accumulated by the cutting operation�
3� Use more water to clean out the residual silt from the water tray�
4� Replace the Drain Plug� Check condition of the O-Ring (E02) and replace if torn or cut�
2� aFter uSe, wipe external surfaces of the tool with clean cloth� Drain water from the water tray and wash out any residue from the sump pump�
3� WarninG! if the supply cord of this power tool is damaged, it must be replaced only by a qualified service technician.
5� The cleaning process is faster and easier if the unit is tipped on end and carefully
(do not wet the motor) hosed down�
6� Wipe the entire unit down including the sides and Sliding Bars (C16)�
7� Clean out the pump by removing the Filter (A26), placing the pump into a container of clean water, and running it to pump out any remaining silt� Back flush the screen Filter (A26) and replace onto the pump�
Page 12 For technical questions, please call 1-888-866-5797.
Item 98265
troubleshooting problem
Tool operates slowly�
possible causes
Tool will not start� 1� Cord not connected�
2� No power at outlet�
3� Tool’s thermal reset breaker tripped (if equipped)�
4� Internal damage or wear� (Carbon brushes or switch, for example�)
1� Extension cord too long or wire size too small�
1� Eliminate use of extension cord�
If an extension cord is needed, use one with the proper diameter for its length and load�
See table a on page 3�
2� Check that shaft spins freely�
3� Have technician service tool�
Performance decreases over time�
Excessive noise or rattling�
Overheating�
2� Arbor shaft binding�
3� Internal damage or wear�
(Carbon brushes, for example�)
1� Accessory dull or damaged�
2� Carbon brushes worn or damaged�
1� Bent or off-balance blade�
2� Bent Arbor Shaft�
3� Internal damage or wear� (Carbon brushes or bearings, for example�)
1� Water flow problem�
2� Not enough water�
3� Running with hot/warm water�
4� Forcing machine to work too fast�
5� Accessory misaligned�
Restricted carriage travel�
6� Accessory dull or damaged�
7� Blocked motor housing vents�
8� Motor being strained by long or small diameter extension cord�
1� Dry or damaged Holder�
2� Bent Sliding Bars�
Likely Solutions
1� Check that cord is plugged in�
2� Check power at outlet� If outlet is unpowered, turn off tool and check circuit breaker�
If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads�
3� Turn off tool and allow to cool�
Press reset button on tool�
4� Have technician service tool�
1� Keep cutting accessories sharp�
Replace as needed�
2� Have qualified technician replace brushes�
1� Replace blade with new one�
2� Check shaft for run-out�
3� Have technician service tool�
1� Check connection�
2� Add proper amount of water�
3� Always run with cold water�
4� Allow machine to work at its own rate�
5� Check and correct accessory to fence and/or table alignment�
6� Keep cutting accessories sharp�
Replace as needed�
7� Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator while blowing dust out of motor using compressed air�
8� Eliminate use of extension cord�
If an extension cord is needed, use one with the proper diameter for its length and load�
See table a on page 3�
1� Lubricate or service Holder components�
2� Replace Sliding Bars�
Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect power supply before service.
Item 98265 For technical questions, please call 1-888-866-5797.
Page 13
parts Lists and Diagrams pLeaSe reaD tHe FOLLOWinG careFuLLy
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY� NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT� IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER� THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO� record product’s Serial number Here:
note: If product has no serial number, record month and year of purchase instead�
note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts�
Page 14 For technical questions, please call 1-888-866-5797.
Item 98265
parts List and Diagram a - Motor part Description
A01 Screw (M5x12)
A02 Hose Connector
A03 Water Tubing
A04 Screw (M5x10)
A05 Inner Flange
A06 Bearing (6202RT)
A07 Washer (14)
A08 Bearing (628-R)
A09 Grounding Wire
A10 Front Motor Cover
A11 Outer Teeth Washer
A12 Screw (M4x8)
A13 Guard
A14 Screw (STS�5x15)
A15 Water Seal
A16 Power Switch
A17 Seal
A18 Cap
Qty
1
1
1
5
1
2
2
2
1
1
1
1
1
1
1
2
5
1
part Description Qty
A19 Switch Body
A20 Thermal Protector
A21 Press Plate
A22 Joint
A23 Cord 1
A24 Water Pump Connector 1
A25 Pump
A26 Filter
2
1
1
1
A27 Clear Guard
A28 Screw (M4x12)
A29 Water Pad
A30 Blade Guard
A31 Rubber Gasket
A32 Arbor Bolt (M8x15)
A33 Outer Flange 1
A34 Blade (sold separately) 1
A35 Bearing Cover
A36 Shaft
1
1
1
1
1
1
1
3
1
1
part Description
A37 Key
A38 Gear
A39 Screw (ST4x30)
A40 Screw (ST3�8x63)
A41 Clip
A42 Stator
A43 Bearing (6001-RT)
A44 Rotor
A45 Bearing (608-RT)
A46 Bearing Cover
A47 Motor Housing
A48 Carbon Brush Cover
A49 Carbon Brush
A50 Brush Housing
A51 Motor Cover
A52 Screw (ST4x15)
Qty
1
4
2
2
1
2
1
1
1
1
1
1
4
1
1
1
Item 98265 For technical questions, please call 1-888-866-5797.
Page 15
parts List and Diagram B - Hanger
part Description
B01 Screw (M4x6)
B02 Screw (M4x20)
B03 Hex Nut (M4)
B04 Linear Bushing
B05 Felt Bushing
B06 Seal
B07 Bearing
B08 Hex Bolt (M6x20)
B09 Holder
B10 Knob
B11 Flat Washer
B12 Screw (M5x12)
B13 Handle
B14 End Cap
2
1
2
1
2
4
1
4
4
2
4
Qty.
3
1
1
Page 16 For technical questions, please call 1-888-866-5797.
Item 98265
parts List and Diagram c - Support
part Description
C01 Steel Support B
C02 Connection Shaft
C03 Set Screw (M4x15)
C04 Flat Washer
C05 Knob
C06 Socket Wrench
C07 Spring Washer
C08 Flat Washer
C09 Wrench Holder
C10 Sliding Bar Support
C11 Screw (M6x8)
C12 Bevel Scale
C13 Flat Washer
C14 Spring Washer
C15 Hex Nut
2
2
1
2
1
4
9
1
1
7
2
2
Qty.
1
2
7 part
C16 Sliding Bar
Description
C17 Tubing Holder
C18 Clip
C19 Wrench
C20 Wrench Holder
C21 Pointer
C22 Sliding Bar Support
C23 Bevel Scale
C24 Screw (M6x15)
C25 Steel Support
C26 Flat Washer
C27 Spring Washer
C28 Hex Bolt (M8x25)
C29 Water Line Scale
8
8
1
1
8
1
4
2
1
1
1
Qty.
2
1
1
Item 98265 For technical questions, please call 1-888-866-5797.
Page 17
parts List and Diagram D - Work table
part Description
D01 Hex Nut (M6)
D02 Spring Washer
D03 Flat Washer
D04 Stainless Steel Frame
D05 Hex Bolt (M6x30)
D06 Table End
D07 Right Fence Cover 1
D08 Scale
D09 Right Fence
D10 Right Fence Cover 2
D11 Left Fence Cover 1
D12 Left Fence
D13 Scale
D14 Left Fence Cover 2
D15 Hex Bolt (M6x15)
1
4
1
1
1
1
1
1
2
1
1
8
Qty.
20
24
24 part Description
D16 Right Worktable
D17 Left Worktable
D18 Miter Gauge
D19 Rivet
D20 Knob
D21 Guide
D22 Knob
D23 Clamp Plate
D24 Clamp Plate Guide
D25 Screw
D26 Table End
D27 Knob
D28 Flat Washer
D29 Table Support
D30 Hex Bolt (M6x25)
4
12
4
8
1
1
1
1
1
1
1
1
Qty.
1
1
1
Page 18 For technical questions, please call 1-888-866-5797.
Item 98265
parts List and Diagram e - Water tray
part
EO1 Water Tray
Description
EO2 O-Ring
EO3 Drain Plug
EO4 Rubber Cap
EO5 Flat Washer
EO6 Set Screw
EO7 Rubber Feet
EO8 Carrying Handle Grip
Qty.
1
1
1
1
7
11
7
2
Item 98265 For technical questions, please call 1-888-866-5797.
Page 19
Limited 90 Day Warranty
Harbor Freight Tools Co� makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase� This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance� We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product� Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you� THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS�
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid� Proof of purchase date and an explanation of the complaint must accompany the merchandise�
If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement� We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product�
This warranty gives you specific legal rights and you may also have other rights which vary from state to state�
3491 Mission Oaks Blvd. • pO Box 6009 • camarillo, ca 93011 • 1-888-866-5797
