Configuration de syst mes et options de serveurs

Configuration de syst mes et options de serveurs
PRIMERGY RX300 S8
System configurator and order-information guide
October 2014
Contents
Instructions
Configuration diagram
Configurator
0 System software
I
Basic unit
II Processor
III Memory
IV Graphics
V Accessible drives
VI Hard disk drives
VII PCI Controller
VIII Raid Controller and Devices for SAS3.0 (12 Gb/sec)
IX Communication/Network
X System Management Products (RemoteView)
XI Miscellaneous
XII Country specific power cord
Change report
PRIMERGY Server
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
Instructions
This document contains basic product and configuration information that will enable you to configure your system via
PC-/System-Architect.
Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete
PRIMERGY Rack system.
You can configure your individual PRIMERGY server in order to adjust your specific requirements.
The System configurator is divided into several chapters that are identical to the current price list and PC-/SystemArchitect.
Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through
the configurator by following the lines from the top to the bottom.
Section
III
Memory, example
There are X memory slots which can be equipped with XXX MB.
It is permissible to make up to X passes through the memory upgrade options
S26361-XXX-XXX
Memory XXX MB
S26361-XXX-XXX
Memory XXX MB
max. X times per system
max. X times per system
X times
In one chapter you can only select as many components (here 4x) as the arrow indicates.
4x
Please note that there are information symbols which indicate necessary information.
For further information see:
http://ts.fujitsu.com/products/standard_servers/index.html
(internet)
https://partners.ts.fujitsu.com/com/order-supply/configurators/primergy_config/current/Pages/default.aspx (extranet)
Fujitsu PRIMERGY Server
2 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
Configuration diagram PRIMERGY RX300 S8
System unit ( I )
with up to 6x 3.5" Hard disk drives
Motherboard
Memory CPU1
front side
Bay for LocalView LCD
LSD
2 USB
Air channel VGA, LAN
Frontpanel
Bay for 5,25"x 0,5" SATA-BR
or DVD-ROM/RW
( Channel A + B + C )
Bank 1 (4 Modules)
Bank 2 (4 Modules)
Bank 3 (4 Modules)
Xeon DP
Memory CPU2
( Channel D + E + F)
Bank 1 (4 Modules)
Bank 2 (4 Modules)
Bank 3 (4 Modules)
Memory (III )
Xeon DP
Processor ( II )
Accessible drives ( V )
rear side
Fan 1 - Fan 5
1. PSU
2. PSU
Redundant Fans
are standard!
Redundant power
supply option
Needs space for 2
hard disk drives!
3.5"x1,6"
Backup drive option
Modular RAID
Support
Raid Card for IME, Raid 0 / 1E
Raid Card for Raid 5
Low-profile extension slots for:
SCSI Controller for backup( VII )
SAS Disk Array ( VIII )
Communication/Network ( IX )
Miscellaneous ( X )
Hard disk drives ( VI )
3.5" SAS/SATA
3.5"x1" SAS or SATA
Slot 6 PCIe-3 x16, 210mm @ CPU2
3.5"x1" SAS or SATA
Slot 5 PCIe-3 x16, 390mm @ CPU2
Slot 4 PCIe-3 x8, max. 390mm @ CPU1
3.5"x1" SAS or SATA
Possibility to install PCIe x16 cards
Slot 3 PCIe-3 x8, max. 390mm @ CPU1
3.5"x1" SAS or SATA
Slot 2 PCIe-3 x8, max. 312mm @ CPU1
3.5"x1" SAS or SATA
Slot 1 PCIe-3 x8, max. 168mm @ CPU1 white colored
Dedicated for modular on-board LAN-Controller
Slot 7 PCIe-3 x8, max. 168mm @ CPU1
3.5"x1" SAS or SATA
Internal slot for modular RAID-Controller
Key:
Included in basic unit
Option
One CPU, one memory per CPU and one PSU has to be selected for an orderable basic unit.
Fujitsu PRIMERGY Server
3 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
Configuration diagram PRIMERGY RX300 S8
System unit ( I )
with up to 4, 8, 12 or 16x 2.5" Hard disk drives or up to 4 or 8 PCIe SSDs 2.5"
Motherboard
Memory CPU1
front side
Bay for LocalView LCD
LSD
2 USB
Air channel VGA, LAN
Frontpanel
Bay for 5,25"x 0,5" SATA-BR
or DVD-ROM/RW
( Channel A + B + C )
Bank 1 (4 Modules)
Bank 2 (4 Modules)
Bank 3 (4 Modules)
Xeon DP
Memory CPU2
( Channel D + E + F)
Bank 1 (4 Modules)
Bank 2 (4 Modules)
Bank 3 (4 Modules)
Memory (III )
Xeon DP
Accessible drives ( V )
Processor ( II )
rear side
Fan 1 - Fan 5
1. PSU
2. PSU
Redundant Fans
are standard!
Needs space for 4
2.5" hard disk drives!
3.5"x1,6"
Backup drive option 1
Redundant power
supply option
Needs space for 8
2.5" hard disk drives!
5.25"x1,6"
Modular RAID
Support
Raid Card for IME, Raid 0 / 1E
Backup drive option 2
Raid Card for Raid 5
Low-profile extension slots for:
SCSI Controller for backup( VII )
SAS Disk Array ( VIII )
Communication/Network ( IX )
Miscellaneous ( X )
Hard disk drives ( VI )
2.5" SAS/SATA
Up to 4 blocks with 4 HDDs
Slot 6 PCIe-3 x16, 210mm @ CPU2
2.5" SAS or SATA
2.5" SAS or SATA
Slot 5 PCIe-3 x16, 390mm @ CPU2
2.5" SAS or SATA
Slot 4 PCIe-3 x8, max. 390mm @ CPU1
Possibility to install PCIe x16 cards
2.5" SAS or SATA
Slot 3 PCIe-3 x8, max. 390mm @ CPU1
Slot 2 PCIe-3 x8, max. 312mm @ CPU1
2.5" SAS
2.5" SAS
Slot 1 PCIe-3 x8, max. 168mm @ CPU1 white colored
Dedicated for modular on-board LAN-Controller
Slot 7 PCIe-3 x8, max. 168mm @ CPU1
2.5" SAS
2.5" SAS
Internal slot for modular RAID-Controller
Key:
Included in basic unit
Option
One CPU, one memory per CPU and one PSU has to be selected for an orderable basic unit.
Fujitsu PRIMERGY Server
4 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
Start PRIMERGY RX300 S8
I
Section
Basic unit
System unit consisting of:
* 2U Housing without power supply modules
* Basic units with:
- 2 Hot-Plug Power Supply Bays
- 5 Fans (full redundancy)
- 12 memory DIMMs per CPU ( max 768GB ) => Total 24 DIMMs ( max 1536GB ) for two CPU`s
* SAS Backplane for 6x 3.5" HD, SAS Backplanes for 4, 8, 12 or 16x 2.5" HD or PCIe Backplanes for
4 or 8 PCIe SSD with cable connection to on-board, modular RAID Controller
* Drives/Bays
- 6 bays 1" for hot plug 3.5" HD (1" high) or 4, 8, 12 or 16 bays for hot plug 2.5" HD
- 1 bay for 3.5" and 1.6" high Backup device, consumes 2 bays for 3.5" HD for basic unit 6x 3.5" HD
not possible for basic unit with 12 or 16 x 2,5" HD
- 1 bay for 5.25" and 1.6" high Backup device, not possible for basic unit 6x 3.5" HD
for basic unit with 12 or 16 x 2,5" HD
- 1 bay SATA-CD- or DVD-ROM 0,5" height (option)
- 1 bay for opt. LocalView LC-Display
* Integrated ServerView Diagnostics Technology ( Diagnosis LED`s ) for indication of internal
failed components
Systemboard D2939-B with:
* Up to two Xeon DP CPU`s (Socket-R)
with 2 serial QPI links ( Quick Path Interconnect ) and four memory channels per CPU
First CPU has to be selected for an orderable basic unit,
* Chipset Intel® C600 Series (codenamed Patsburg)
* 7 PCI slots:
- 2x PCIe-3 x16 (both slots are connected to CPU 2 and are useable with configured 2nd CPU only!)
- 4x PCIe-3 x8 (one notched to install x16 cards)
- 1x PCIe-3 x8 (for internal modular RAID controller only)
* 24 memory slots for max. 1536GB RAM DDR3 available
- Memory is divided into 12 DIMMs per CPU ( 4 channels with 3 slots per channel )
Possible max. configurations are:
16x 8GB UDIMM (dual rank modules) = 128GB
24x 16GB RDIMM (dual rank modules) = 384GB
24x 32GB LRDIMM (quad rank modules) = 768GB
24x 64GB LRDIMM (eight rank modules) = 1536GB
First Memory ( one module ) has to be selected for an orderable basic unit per CPU
- Memory upgrade is possible module wise
- Memory mirrroring is supported with 2 identical modules in channel A+B CPU 1 or D+E CPU 2
- Hot Spare Memory is supported with 3 identical modules in channel A+B+C CPU 1 or D+E+F CPU 2
- SDDC (Chipkill) is supported for memory modules,
* Dual Port 10/100/1000 x4 PCI Express* Gigabit Ethernet Intel LAN controller Powerville on-board
* iRMC S4 (integrated Remote Management Controller) on-board server management controller with
dedicated 10/100/1000 Service LAN-port and integrated graphics controller.
The Service LAN-port can be switched alternatively on standard Gbit LAN port 1
* Graphics Controller integrated in iRMC S4 (integrated Remote Management Controller):
1600x1200x16bpp 60Hz, 1280x1024x16bpp 60Hz, 1024x768x32bpp 75Hz, 800x600x32bpp 85Hz,
640x480x32bpp 85Hz
(1280x1024x24bpp 60Hz only possible if local monitor or remote video redirection is off)
Interfaces at the rear:
* 1x RS-232-C (serial, 9 pins) (usable for BMC or OS or shared)
* 1x VGA (15 pins)
* 4x USB 2.0 ( UHCI ) with 480MBit/s, no USB wakeup
* 2x LAN RJ45, 1x Service-LAN RJ45
Interfaces on the front:
* 2x USB 2.0 ( UHCI ) with 480MBit/s, no USB wakeup
* 1x VGA (15 pins) as an option
* 1x Service-LAN RJ45 as an option
Interfaces internal:
* 1x released internal USB Interfaces for backup devices,
* 1x USB 2.0 (UHCI) with 480MBit/s for dongle funcionality (uSSD memory), no USB wakeup
* 1x SATA interface for DVD (only usable with 4x 2.5" HDD + DVD Option)
* 4x SATA/SAS interface for 4 SATA/SAS HD`s or SAS Backup device
* 2x USB 2.0 ports for internal USB redirection connected to BMC
Software:
* ServerView Suite Software package incl. ServerStart, ServerBooks, Management Software and Updates
* Documentation engl. (multilingual on CD)
A
Fujitsu PRIMERGY Server
5 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
A
Cables included in basic unit
Connections
Cable
PRIMERGY RX300 S7
1. SATA DVD


2. SAS cables to HDDs


3. 1x cable for SAS signaling


 SAS
 SATA
Note: Rack Mounting kit and Power Cord for RX300S7 is not included in the basic unit and
has to be configured separately
Rack version for 19'' racks with
Basic unit with 2.5" HDD bays is modular expandable with various modules for backup devices
integration or up to 16x 2.5" HDDs.
Details and pictures see Section Va:
Possible configuration options for basic units
No PSU included in Base Unit
Basic unit is without CPU and Memory
For an orderable basic unit one CPU = first CPU and
one memory = first memory has to be selected
Basic unit with
6x 3.5" HDD bays fixed
S26361-K1457-V101
Basic unit with
2.5" HDD bays expandable
S26361-K1457-V401
Basic unit with
8x 2.5" HDD bays fixed
S26361-K1457-V201
Basic unit with
12x 2.5" HDD bays fixed
S26361-K1457-V301
Full redundancy cannot be guaranteed for a max.
config. with e.g. two 135W CPUs with 450W PSUs.
In this case SysArch will generate a warning and
Power Safeguard will throttle CPUs
in case of a PSU failure.
So, power consumption will be limited to 450W.
* 110V range not supported
S26113-F575-E12
450W PSU module platinum
S26113-F574-E12
800W PSU module platinum
S26113-F609-E10
800W PSU module -48V DC gold
S26113-F615-E10 *
800W PSU module titanium
1st or 2nd PSU for redundancy
1st or 2nd PSU for redundancy
1st or 2nd PSU for redundancy
1st or 2nd PSU for redundancy
94% efficiency (platinum)
94% efficiency (platinum)
92% efficiency (gold)
96% efficiency (titanium)
uses hot plug PSU slot
uses hot plug PSU slot
uses hot plug PSU slot
uses hot plug PSU slot
min. 1 / max. 2x per system
min. 1 / max. 2x per system
min. 1 / max. 2x per system
min. 1 / max. 2x per system
as soon as available
S26113-F574-E99 *
For later redundancy upgrade the following kit is available:
Power Supply Dummy
One 450W power supply module hot plug
must be ordered if 1x PSU only
no power cable included!!!
occupies one bay for
One 800W power supply module hot plug
hot plug power supply
no power cable included!!!
max. 1x per system
One 800W -48V DC PSU hot plug
no power cable included!!!
S26113-F609-L10
One 800W power supply module titanium
S26113-F615-L10
S26113-F575-L12
S26113-F574-L12
as soon as available
no power cable included!!!
Please order appropriate power cord additionally:
*For order completeness only
Powercord for rack, 4m, grey, IEC320 C13->C14 connector
T26139-Y1968-L10
Not shown in system architect
Power Cord USA / Canada, 1.8m, grey
T26139-Y1742-L10
Version > V9.2
Power Cord -48V DC, 4m, black
T26139-Y4024-L10
S26361-F3552-E1
TPM Module
Trusted Platform Module on Motherboard
Use according to import restrictions
S26361-F3552-L1
max. 1x per system
TPM Module add-on kit
for later integration (loose delivery)
Trusted Platform Module on Motherboard
Be aware of import restrictions!
Use according to import restrictions
Loose delivery for later
max. 1x per system
integration possible for customer.
B
Fujitsu PRIMERGY Server
6 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
B
PRIMECENTER Rack
S26361-F2735-E145
RMK-F1_DI_CMA_QRL
S26361-F2735-E175
Rack Mount Kit F1-C S7 LV
S26361-F2735-E111
Further information for
No Rackmount-Kit option
rack mounting is available
best choice for PrimeCenter racks
best choice for 3rd party racks
Only for loose deliveries
within the
consisting of
consisting of
No mounting in racks possible
Corporate Partner Portal
vario carrier 714-785mm
vario carrier 559-914mm
telescopic drop-in rails 781mm
telescopic drop-in rails 781mm
with quick release lever support
with quick release lever support
with full extraction
with full extraction
with CMA adapter
with CMA adapter
1x per system
1x per system
max. 1x per system
All "L" no's for loose delivery
S26361-F2735-L10
Adapter angle PC/DC-Rack, till 50Kg
C
S26361-F4530-E11
S26361-F4530-E10
Bracket 1U in asymmetrical racks
Mounting of RMK in symmetrical racks
(no support brackets needed)
necessary for mounting RMKs in
asymmetrical PC racks
S26361-F2735-L145
RMK-F1_DI_CMA_QRL
best choice for PrimeCenter racks
with CMA adapter
S26361-F2735-L175
RMK-F1_DI_CMA_QRL_LV
best choice for 3rd party racks
S26361-F2735-E71
Lateral cable management
S26361-F2735-E82
Rack Cable Management Arm CMA 2U
with CMA adapter
for 2U servers or higher
for 2U Server in racks
S26361-F2735-L176
- for asymmetrical racks
- for symmetrical racks
M1 or 3rd party racks
RMK-F1_DI_QRL_LV
best choice for 3rd party racks
Fujitsu racks
w/o CMA adapter
PRIMECENTER S2 or M1
- 1 bracket PC Rack asym.
1x per system
1x per system
S26361-F2735-L7
Lateral cable management (optionally)
can only be mounted
SNP:SY-F1647E301-P
in asymmetrical PRIMECENTER
S2 or new M1 racks in 1U above RMK
Installation ex works for one
server or subsystem.
Hereby the rack will be delivered
completely pre-mounted and
S26361-F2735-L82
Rack Cable Management Arm CMA 2U
all wired connections are tested.
for 2U Server in racks.
With PCR M1 16U, 24U, 42U:
Systems and components
S26361-F2201-L20
Cable arm 2U PCR M1 S and 3rd p.-racks
will be delivered installed in the rack
"Rack-mounting ex factory"
for L176, has to be mounted above RMK
This service is to be ordered once
per installable server/storage
subsystem, in order to get the
To be ordered only together with
server/storage subsystem
a PRIMECENTER rack
mounted into the racks.
PCR S2 e.g. S26361-K826-V10x
In case of not-installed server and subsystems
new PCR M1 e.g. S26361-K827-Vxxx
this service has to be ordered,
refer PCR S2 or M1 rack configurator
to get the mounting kits and the
max. 1x per System
cables installed.
PRIMERGY Classic 19" rack is not supported
C
Fujitsu PRIMERGY Server
7 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
C
II
Section
Processor
There are 2 processor sockets available.
The first socket must always be equipped with the first CPU which can be selected via configurator
It is also possible to upgrade a dual-processor system later on with a second CPU
Both PCIe-3 x16 slots are connected to CPU 2 and are useable with configured 2nd CPU only!
Two processors with different clock frequencies are not possible
A multi-processor operating system is required for a dual-processor system.
Max. two CPU`s can be selected per basic unit
One of following CPU´s has to be selected as first CPU
for an orderable basic unit
Optional second CPU has to be the same type like the first CPU
Basic 4C CPU's
- 1x 64-bit Intel Xeon (10MB Smart Cache)
1333 MHz DDR3 Bus; 6,40 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2603v2 4C/4T 1.80GHz 10MB 6.40GT/s 1333MHz 80W
Xeon E5-2609v2 4C/4T 2.50GHz 10MB 6.40GT/s 1333MHz 80W
S26361-F3788-E180
S26361-F3788-E250
Standard Turbo 6C/8C CPU's
- 1x 64-bit Intel Xeon (15/20MB Smart Cache); Hyper-Threading (HT);
1600 MHz DDR3 Bus; 7,20 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2620v2 6C/12T 2.10GHz 15MB 7.20GT/s 1600MHz 80W
Xeon E5-2630v2 6C/12T 2.60GHz 15MB 7.20GT/s 1600MHz 80W
Xeon E5-2640v2 8C/16T 2.00GHz 20MB 7.20GT/s 1600MHz 95W
Advanced Turbo+ 8C/10C CPU`s
- 1x 64-bit Intel Xeon (20/25MB Smart Cache); Hyper-Threading (HT);
1866 MHz DDR3 Bus; 8,00 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
S26361-F3789-E210
S26361-F3789-E260
S26361-F3789-E200
Xeon E5-2650v2 8C/16T 2.60GHz 20MB 8.00GT/s 1866MHz 95W
S26361-F3790-E260
Xeon E5-2660v2 10C/20T 2.20GHz 25MB 8.00GT/s 1866MHz 95W
Xeon E5-2670v2 10C/20T 2.50GHz 25MB 8.00GT/s 1866MHz 115W
S26361-F3790-E220
S26361-F3790-E250
Xeon E5-2680v2 10C/20T 2.80GHz 25MB 8.00GT/s 1866MHz 115W
Xeon E5-2690v2 10C/20T 3.00GHz 25MB 8.00GT/s 1866MHz 130W
Segment Optimized CPU`s
- 1x 64-bit Intel Xeon (15/25/30MB Smart Cache); Hyper-Threading (HT);
S26361-F3790-E280
S26361-F3790-E300
Max. DDR3 Bus Speed depends on:
- max. DDR3 Bus Speed from the CPU and
- max. DDR3 Memory Speed and
- max. memory modules on one memory channel
For CPUs which do not offer 1866 MHz support,
(Basic, Standard & Low Power class),
System Architect will not offer memory modules
supporting this frequency.
1866 MHz DDR3 Bus; 8,00 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2637v2 4C/8T 3.50GHz 15MB 8.00GT/s 1866MHz 130W
Xeon E5-2643v2 6C/12T 3.50GHz 25MB 8.00GT/s 1866MHz 130W
Xeon E5-2667v2 8C/16T 3.30GHz 25MB 8.00GT/s 1866MHz 130W
Xeon E5-2695v2 12C/24T 2.40GHz 30MB 8.00GT/s 1866MHz 115W
Xeon E5-2697v2 12C/24T 2.70GHz 30MB 8.00GT/s 1866MHz 130W
Low Power 6C/10C CPU's
- 1x 64-bit Intel Xeon (15/25MB Smart Cache); Hyper-Threading (HT);
1600 MHz DDR3 Bus; 7,20/8,00 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2630Lv2 6C/12T 2.40GHz 15MB 7.20GT/s 1600MHz 60W
Xeon E5-2650Lv2 10C/20T 1.70GHz 25MB 8.00GT/s 1600MHz 70W
S26361-F3791-E350
S26361-F3791-E330
S26361-F3791-E300
S26361-F3791-E240
S26361-F3791-E270
S26361-F3792-E240
S26361-F3792-E170
D
Fujitsu PRIMERGY Server
8 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
D
IV
Section
Graphics
Graphics Controller integrated in iRMC S3 (integrated Remote Management Controller):
1600x1200x16bpp 60Hz, 1280x1024x16bpp 60Hz, 1024x768x32bpp 75Hz, 800x600x32bpp 85Hz, 640x480x32bpp 85Hz
(1280x1024x24bpp 60Hz only possible if local monitor or remote video redirection is off)
S26361-F2571-E26
Optional Front-VGA
for Onboard Controller only
consists of internal cable and
front VGA connector
max. 1x per system
The hight end optional NVIDIA NVS300 graphic card offers dual head operation and fully 3D video support.
The cables for either two times DVI-I or VGA (cable kit) connections are part of the delievery.
Optional Front-VGA S26361-F2571-E26 cannot be ordered if NVS300 is required.
Remote Video direction via iRMC must be disabled.
This PCIe-x1 card can also be installed in any PCIe-x4, x8 or x16 slot.
Only one card per server is allowed.
max. 1x
S26361-F2748-E637
PY VGA LP card 256MB PCI-e x1
NVIDIA NVS300
512 MB PCIe-x1
Connectors: 1x LFH 59
cable kit for 2x DVI or 2x VGA
cable kits included
Dual head + professional 2-D + 3-D
supported for Windows OS
native driver support for Linux OS
low profile bracket
max. 1x per system
PY VGA card must be installed in slot 4 (x8 wired x8)
S26361-F2748-L637
PY VGA LP card 512MB PCI-e x1
for loose delivery
E
Fujitsu PRIMERGY Server
9 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
E
III
Section
Memory
- There are 12 memory slots per CPU for max.
768GB LRDIMM (12x 64GB 8R)
192GB RDIMM (12x 16GB 2R)
64GB UDIMM (8x 8GB) on special Release only
=> max. 1.536GB for two CPU`s (768GB per CPU), using LRDIMM
- The memory area is divided into 4 channels per CPU with 3 slots per channel
- Slot 1 of each channel belongs to memory bank 1, the slot 2 belongs to memory bank 2,
slot 3 belongs to memory bank 3
Registered, LR DIMMs and unbuffered memory modules can be selected
No mix of registered, load reduced and unbuffered modules allowed.
Memory can be operated at 1.5V or 1.35V, even if the modules are of low voltage type.
Memory operating voltage can be set within BIOS (1.5V is default setting for max. speed).
In a single DIMM per channel configuration, following frequencies are supported:
- 1.5V - 1866MHz max (depending on CPU)
- 1.35V - 1600MHz max (depending on CPU, up to two LRDIMM per channel)
- 1.35V - 1333MHz max (up to two UDIMM or RDIMM per channel)
SDDC
In a 3 DIMMs
(Chipkill)
perischannel
supported
configuration,
for registered
memory
/ load
will operate
redueced
at 1.35V
x4 organized
or 1.5V (no
memory
UDIMM
modules
allowed).
only
SSD (Chipkill) is supported for registered / load reduced x4 organized memory modules only.
1.) In the "Independent Channel Mode" is following configuration possible
Channels can be populated in any order in Independent Channel Mode. All four
channels may be populated in any order and have no matching requirements. All
channels must run at the same interface frequency but individual channels may run at
different DIMM timings (RAS latency, CAS latency, and so forth)
No mix of registered, load reduced and unbuffered modules allowed.
2.) "Rank Sparing Mode" configuration
- Within a memory channel, one rank is a spare of the other ranks.
The Spare Rank is held in reserve and is not available as system memory
For the effective memory capacity, please refer to the spreadsheet below.
The BIOS is set to the rank sparing setting.
Minimum configuration is: 2x 1R, 2x 2R or 1x4R DDR3 module per channel
This mode is not supported by unbuffered memory modules
3.) "Performance Mode" configuration
- In this configuration, the memory module population ex factory is spread across all channels.
The BIOS is set to the max. performance for memory.
Minimum configuration is: 4x identical modules
4.) In the "Mirrored Channel Mode" is following configuration possible
- Each memory bank can optionally be equipped with 4x registered or load reduced or unbuffered DDR3 modules
In each memory bank channel A and B / C and D of CPU 1 or channel E and F / G and H of CPU 2 have to be
equipped with identical modules for mirrored channel mode.
In channel B / D is always the mirrored memory of channel A / B of CPU 1
In channel F / H is always the mirrored memory of channel E / G of CPU 2
Minimum configuration is: 4x identical modules
This mode is not supported by unbuffered memory modules
F
Fujitsu PRIMERGY Server
10 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
F
S26361-F3694-E10
Independent Mode
Independent Channel Mode allows all channels to be populated in any order. No specific Memory RAS features are defined
Requires min 1 memory Module per CPU
S26361-F3694-E1
Rank Sparing Mode Installation
BIOS Setup factory preinstalled to this mode. One Rank is spare of other ranks on the same channel. Spare Rank is not shown in System Memory.
For effective capacity within a channel, please have a look below.
1x per CPU
Supported for RDIMM / LRDIMM only.
Requires min 2x 1R/2R or 1x 4R modules per CPU
S26361-F3694-E2
Performance Mode Installation
BIOS Setup factory preinstalled for max. Performance, LV memory might be set to 1.5V operation. Four identical memory modules
will be equipped in one memory bank to achieve highest memory performance. All four modules are active and full capacity can be used.
Multiple of 4 identical modules to be configured per CPU
S26361-F3694-E3
Mirrored Channel Mode Installation
BIOS Setup factory preinstalled to this mode. Four identical memory modules are always equipped in one memory bank to use the
Mirrored channel Mode. Only two modules contain active data, the remain two modules contain mirrored data
Supported for RDIMM / LRDIMM only.
Multiple of 4 identical modules to be configured per CPU
Effective Memory capacity / Rank Sparing Mode, 1 Channel populated
RDIMM
LRDIMM
4GB 1R 8GB 1R 8GB 2R 16GB 2R 32GB 4R 64GB 8R
1DPC
na
na
na
na
24GB
48GB
2DPC
4GB
8GB
12GB
28GB
56GB
112GB
3DPC
8GB
16GB
20GB
44GB
80GB
160GB
Minimum one memory module or order code per CPU = first memory
Note 1.)
Unbuffered Memory (UDIMM) no SDDC (chipkill) support
- one DDR3 unbuffered ECC mem. Module, 1.35V
Choose up to 8 order codes per CPU
8GB (1x8GB) 2Rx8 L DDR3-1600 U ECC
S26361-F3807-E515
special release only
Registered Memory (RDIMM) with SDDC (chipkill) support
- one DDR3 registered ECC mem. Module, 1.35V
Note 1)
1333MHz supported with up to 2DPC (8 modules/CPU) and 1.35V
Max. DDR3 memory speed depends on the memory configuration
1600MHz supported with up to 2DPC (8 modules/CPU) and 1.5V
(No of mem modules per channel) as well as on the CPU type.
Choose up to 12 order codes per CPU
The memory channel with the lowest speed defines the speed
4GB (1x4GB) 1Rx4 L DDR3-1600 R ECC
S26361-F3781-E514
of all CPU channels in the system, also for the channels of the
8GB (1x8GB) 1Rx4 L DDR3-1600 R ECC
16GB (1x16GB) 2Rx4 L DDR3-1600 R ECC
S26361-F3781-E515
S26361-F3781-E516
second CPU if configured.
For real memory speed (depending on memory type / population),
Registered Memory (RDIMM) with SDDC (chipkill) support
8/12x per
- one DDR3 registered ECC mem. Module, 1.5V
CPU, max.
1866MHz supported with up to 2DPC (8 modules/CPU)
2/3 modules
per channel
Choose up to 12 order codes per CPU
16GB (1x16GB) 2Rx4 DDR3-1866 R ECC
please check the spreadsheet "Memory speed" below
S26361-F3793-E516
Registered Memory (RDIMM) no SDDC (chipkill) support
Note 2)
- one DDR3 registered ECC mem. Module, 1.5V
Mix of memory modules is only possible within the same group
No mix with any other types of memory modules possible
1866MHz supported with up to 2DPC (8 modules/CPU)
Choose up to 12 order codes per CPU
8GB (1x8GB) 2Rx8 DDR3-1866 R ECC
S26361-F3793-E515
Load Reduced Memory (LRDIMM) with SDDC (chipkill) support
- one DDR3 load reduced ECC mem. Module, 1.35V
Choose up to 12 order codes per CPU
32GB (1x32GB) 4Rx4 L DDR3-1600 LR ECC
64GB (1x64GB) 8Rx4 L DDR3-1333 LR ECC
S26361-F3782-E517
S26361-F3783-E518
Load Reduced Memory (LRDIMM) with SDDC (chipkill) support
- one DDR3 load reduced ECC mem. Module, 1.5V
1866MHz supported with up to 2DPC (8 modules/CPU)
Choose up to 12 order codes per CPU
32GB (1x32GB) 4Rx4 DDR3-1866 LR ECC
S26361-F3848-E517
G
Fujitsu PRIMERGY Server
11 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
Memory Configuration PRIMERGY RX300 S8
Each CPU offers 12 Slots for DDR3 Memory Modules organised in 3 Banks and 4 Channels.
If you need more than 12 Slots you have to configure the 2nd CPU.
Depending on the amount of memory configured you can decide between 4 basic modes of operation (see explanation below).
There are 3 different kinds of DDR3 Memory Modules available: UDIMM / RDIMM and LRDIMM
UDIMM / RDIMM / LRDIMM offer different functionality. Mix of UDIMM / RDIMM / LRDIMM is not alloved.
If 1.5V and 1.35V DIMMs are mixed, the DIMMs will run at 1.5V
Mode
Configuration
UDIMM RDIMM
RDIMM Application
LRDIMM
x4
x8
x8
SDDC (chipkill) support
any
no
no
yes
Independant Channel
1, 2 or 3 Modules per Bank
yes
yes
yes
Mode
Mirrored Channel Mode *) 4 identical Modules / Bank
no
no
yes
Performance Mode
4 identical Modules / Bank
yes
yes
yes
Rank Sparing Mode *)
min. 2 Ranks / Channel
no
no
yes
*) For the delivery ex works the system will be prepared with dedicated BIOS setting.
Capacity
Min. Memory per CPU
Max. Memory per CPU
Max. Memory per System
Configuration
1 Module / CPU
8/12 Modules / CPU
16/24 Modules / System
detect multi-bit errors
offers max. flexibility, upgradeability, capacity
use UDIMM modules for lowest cost
offers maximum security
offers maximum performance and capacity
balances security and capacity
UDIMM RDIMM LRDIMM
1x4GB
1x4GB
1x32GB
8x4GB 12x16GB 12x64GB
64GB
384GB
1536GB
Notes
with one CPU
with one CPU
if second CPU is configured
Memory-Speed:
Max. DDR3 memory speed depends on the memory configuration on one memory channel and the speed of the CPU
The memory channel with the lowest speed defines the speed of all CPU channels in the system
Mem. Speed provided
by CPU
Real maximum memory-bus speed depending on CPU type, memory configuration (DPC)
and voltage setting (BIOS)
UDIMM 1866MHz
Voltage setting (BIOS)
1.5V [default]
1
2
3
RDIMM 1866MHz
1.35V
1
2
1.5V [default]
3
1
2
3
LRDIMM 4R 1866MHz
1.35V
1
2
1.5V [default]
3
1
2
3
1.35V
1
2
3
DPC
DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC
DPC
CPU with 1866MHz DDR3 Bus
1866
1600
-
1333
1333
-
1866
1866
1066
1333
1333
800
1866
1866
1066
1600
1600
1066
CPU with 1600MHz DDR3 Bus
1600
1600
-
1333
1333
-
1600
1600
1066
1333
1333
800
1600
1600
1066
1600
1600
1066
CPU with 1333MHz DDR3 Bus
1333
1333
-
1333
1333
-
1333
1333
1066
1333
1333
800
1333
1333
1066
1333
1333
1066
1R - Single Rank
2R - Dual Rank
4R - Quad Rank
8R - Eight Rank
1DPC = 1 DIMM per Channel
2DPC = 2 DIMM per Channel
3DPC = 3 DIMM per Channel
Configuration hints:
- The memory sockets on the systemboard offer a color coding:
Bank I
black sockets
Bank II blue sockets
Bank III green sockets
- A so called Bank consits of 1 memory module on every Channel available on one CPU (examples see below)
Bank I on CPU 1/2
up to 4 memory modules connected to Channel A - H on the 1st/2nd CPU
Bank II on CPU 1/2
up to 4 memory modules connected to Channel A - E on the 1st/2nd CPU
Bank III on CPU 1/2
up to 4 memory modules connected to Channel A - E on the 1st/2nd CPU
(can not be populated by UDIMM or 4R RDIMM memory modules)
- See below and next page for a detailed descriptions of the memory configuration supported.
Fujitsu PRIMERGY Server
12 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
1. Independent Channel Mode
required
required if 2nd CPU is configured
Channel C
Ahannel BChannel CChannel D Channel C
Ehannel Channel
F
C
Ghannel H
Bank I
Data
Data
Data
Data
Data
Data
Data
Data
optional, same type in Bank per CPU
(black sockets)
Bank II
Data
Data
Data
Data
Data
Data
Data
Data
optional, any type
(blue sockets)
Bank III Data
Data
Data
Data
Data
Data
Data
Data
-------- not used
(green sockets)
1st XEON CPU (4/6/8 Core)
2nd XEON CPU (4/6/8 Core)
Independent Channel Mode allows all channels to be populated in any order
Can run with differently rated DIMMs and use the settings of the slowest DIMM installed in the system
2. Mirrored Channel Mode
required
required if 2nd CPU is configured
Channel C
Ahannel BChannel CChannel D Channel C
Ehannel Channel
F
Channel
G
H
Bank I
Data
Mirror
Data
Mirror
Data
Mirror
Data
Mirror
optional, same type in Bank per CPU
(black sockets)
Bank II
Data
Mirror
Data
Mirror
Data
Mirror Data
Mirror
-------- not used
(blue sockets)
Bank III Data
Mirror
Data
Mirror
Data
Mirror Data
Mirror
(green sockets)
1st XEON CPU (4/6/8 Core)
2nd XEON CPU (4/6/8) Core)
Mirrored Channel Mode requires identical modules on channel A,B, C, D (1st CPU) or channel E, F, G and H (2nd CPU)
50% of the capacity is used for the mirror => the available memory for applications is only half of the installed memory
If this mode is used, a multiple of 4 identical modules has to be ordered.
3. Performance Channel Mode
required
required if 2nd CPU is configured
Channel Channel
A
BChannel CChannel D Channel C
Ehannel C
F hannel C
Ghannel H
Bank I
Data
Data
Data
Data
Data
Data
Data
Data
optional, same type in Bank per CPU
(black sockets)
Bank II
Data
Data
Data
Data
Data
Data
Data
Data
optional, any type
(blue sockets)
Bank III Data
Data
Data
Data
Data
Data
Data
Data
-------- not used
(green sockets)
1st XEON CPU (4/6/8 Core)
2nd XEON CPU (4/6/8) Core)
Performance Channel Mode requires identical modules on all channels of each Bank per CPU.
If this mode is used, a multiple of 4 identical modules has to be ordered.
Fujitsu PRIMERGY Server
13 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
4. Rank Sparing Mode
1-Rank Memory modules (RDIMM)
required
required if 2nd CPU is configured
Channel C
Ahannel BChannel CChannel D Channel Channel
E
C
F hannel C
Ghannel H
Bank I
Spare
(black sockets)
Bank II
Data
(blue sockets)
Bank III
Data
(green sockets)
Spare
Spare
Spare
Spare
Spare
Spare
Spare
optional, same type in Channel per CPU
Data
Data
Data
Data
Data
Data
Data
optional, any type
Data
Data
Data
Data
Data
Data
Data
1st XEON CPU (4/6/8 Core)
-------- not used
2nd XEON CPU (4/6/8) Core)
2-Rank Memory modules (RDIMM)
Bank I
(black)
Channel Channel
A
BChannel CChannel D Channel Channel
E
Channel
F
C
Ghannel H
R1 Spare Spare
Spare
Spare
Spare
Spare
Spare
Spare
R2 Data
Data
Data
Data
Data
Data
Data
Data
Bank II
(blue)
R1 Data
R2 Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Bank III
(green)
R1 Data
R2 Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
required
required if 2nd CPU is configured
optional, same type in Channel per CPU
optional, any type
-------- not used
1st XEON CPU (4/6/8 Core)
2nd XEON CPU (4/6/8) Core)
4-Rank Memory modules (LRDIMM)
Channel C
Ahannel BChannel CChannel D Channel Channel
E
C
F hannel C
Ghannel H
Bank I
(black)
R1
R2
R3
R4
Spare
Data
Data
Data
Spare
Data
Data
Data
Spare
Data
Data
Data
Spare
Data
Data
Data
Spare
Data
Data
Data
Spare
Data
Data
Data
Spare
Data
Data
Data
Spare
Data
Data
Data
R1
R2
R3
R4
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
R1
R2
R3
R4
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
required
required if 2nd CPU is configured
optional, same type in Channel per CPU
Bank II
(blue)
Bank III
(green)
1st XEON CPU (4/6/8 Core)
optional, any type
-------- not used
2nd XEON CPU (4/6/8) Core)
Rank Sparing Mode requires identical modules (same capacity and technology) within the same channel.
The available memory for applications will vary depending on configuration. Please refer to the spreadsheet above
"Effective Memory capacity with active Rank Sparing Mode". Population rule for Rank sparing mode is to achieve max.
available memory, e.g. 6 DIMMs will be spread across two channels, each with 3DPC
Fujitsu PRIMERGY Server
14 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
G
Va
Section
Possible configuration options for basic units
Config 1: 6x or 4x 3.5” HDD + 3.5" DDS/RDX drive
Is fixed due to selection of basic unit with:
6x 3,5" HDD bays fixed
S26361-K1457-V101
SAS3.0 available since Q2/2014
Basic unit S26361-K1457-V401 with
Config 2: 4x 2.5” HDD
no PCIe SSD SFF
expandable
S26361-F1373-E420
*)
Available Upgrade kits for this configuration option:
Upgrade kit to 8x 2.5" HDD
S26361-F1373-L424
Upgrade kit to 12x 2.5" HDD
S26361-F1373-L427
Upgrade kit to 4x 2.5" HDD + LTO
S26361-F1373-L423
Upgrade kit to 4x + 8x 2.5" SAS3.0
S26361-F1373-L572
Basic unit S26361-K1457-V401 with
Config 3: 4x 2.5” HDD + LTO
expandable
S26361-F1373-E430
expandable
Basic unit S26361-K1457-V401 with
Available Upgrade kits for this configuration option:
Upgrade kit to 8x 2.5" HDD
S26361-F1373-L436
Basic unit S26361-K1457-V201 with
Config. 4: 8x 2,5" HDD bays fixed
S26361-K1457-V201
Available Upgrade kits for this fixed configuration:
Upgrade kit to 12x 2.5" HDD
S26361-F1373-L247
Upgrade kit to 16x 2.5" HDD
S26361-F1373-L248
Basic unit S26361-K1457-V401 with
Config 5: 8x 2.5“ HDD + 3.5“ drive
expandable
S26361-F1373-E450
Config 12: 3.5" drive + 8x SAS3.0
S26361-F1373-E550
No Upgrade kit available!
Basic unit S26361-K1457-V401 with
Config 6: 8x 2.5” HDD + LTO
expandable
S26361-F1373-E460
Config 15: LTO + 8x SAS3.0
no ODD and LSD bay available!
No Upgrade kit available!
S26361-F1373-E560
Basic unit S26361-K1457-V301 with
Config 7: 12x 2,5" HDD bays fixed
S26361-K1457-V301
Basic unit S26361-K1457-V401 with
expandable
Config 10: 4x SAS2.0 + 8x SAS3.0
S26361-F1373-E572
Note: 4x SAS2.0 connected to on-board RAID Ctrl!
Available Upgrade kits for this configurations:
Upgrade kit to 16x 2.5" HDD
S26361-F1373-L378
Basic unit S26361-K1457-V401 with
Config 8: 16x 2.5” HDD
no ODD and LSD bay available!
No Upgrade kit available!
expandable
S26361-F1373-E480
Includes all necessary bezels, cages, backplanes and cables
*) these are the only noHDD/SSD configuration opportunity without needed RAID controller
H
Fujitsu PRIMERGY Server
15 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
H
Vb
Section
Accessible drives
Setup RX300 S7 by ServerStart is supported with following configurations:
no DVD, no CD:
remote installation only ( PXE service & DHCP server required)
built in CD/DVD or USB CD/DVD disk drive:
UNC Network share reachable or USB Floppy connected
USB Floppy, no CD/DVD:
USB CD/DVD connected
If installation is done locally, make sure you have
external FDD available for driver installation.
S26361-F3269-E2
S26361-F3641-E2
DVD-RW supermulti slim SATA
Blu-ray Triple Writer slim SATA
all formats, DUAL/DL, DVD-RAM
6x BD-RW, 8x DVD, 24x CD
1x
BD DL and all CD/DVD formats
0.5 x 5.25", black bezel
0.5 x 5.25"
max. 1x per system
max. 1x per system
USB 3.0 adapter
S26361-F3749-E201
USB3.0 PCIe x1 adapter card lp
Sunrich U-720
The adapter is also available as optional (loose) delivery
with FH and LP bracket included
S26361-F3749-L501
PCIe x1
1 port intern, 1 port extern
USB 3.0 A jacks
max. 1x per system
RDX drives perform better with
USB 3.0 Controller
Only for basic unit
V4xx
S26361-F3750-E5
RDX Drive USB3.0 3.5" internal
100MB/s, USB 3.0
Connector: USB 3.0 "B"
with USB cable
without RDX cartridges
1.6 x 3.5", black bezel
max. 1x per system
Only for basic unit
V1xx
S26361-F3750-E7
RDX Drive USB3.0 3.5" internal
100MB/s, USB 3.0
Connector: USB 3.0 "B"
within tape cage w/ USB cable
without RDX cartridges
1.6 x 3.5", black bezel
max. 1x per system
RDX cartridges must be ordered separately
RDX 320GB = S26361-F3857-L320
RDX 500GB = S26361-F3857-L500
RDX 1TB = S26361-F3857-L600
10x RDX320 = S26361-F3857-L329
The drive is also available as optional (loose) delivery
S26361-F3750-L5/L7 with USB3.0 cable for adapter card.
The USB3.0 Adapter card or the USB2.0 cable set
S26361-F3750-L20 must be ordered with the drive!
H
Fujitsu PRIMERGY Server
16 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
H
SAS Controller for internal Backup Drives
S26361-F3674-E1
Onboard 4 port SAS Controller
For external SAS Backup drives
an additional SAS controller has to be configured
LSI
Only for basic unit
V4xx
Patsburg B
RAID 0, 1 & 10
no controller cache
SAS 1.0 (3Gb/sec)
4 internal ports
PCIe x4
no PCI slot required
max. 1x per system
as soon as available
1x
S26361-F3626-E2
S26361-F3627-E1
S26361-F3787-E1
Tape drive LTO4 HH SAS IBM V2
Tape drive LTO5HH Ultrium SAS
Tape drive LTO6HH Ultrium SAS
800GB, 120MB/s, SAS 6Gb
1500GB, 140MB/s, SAS 6Gb
2500GB, 160MB/s, SAS 6Gb
Connector: mini-SAS
Connector: mini-SAS
Connector: mini-SAS
incl. SAS cable
incl. cleaning cartridge
incl. SAS cable
incl. cleaning cartridge
incl. SAS cable
incl. cleaning cartridge
without data cartridge
without data cartridge
without data cartridge
1.6 * 5.25"
1.6 * 5.25"
1.6 * 5.25"
max. 1x per system
max. 1x per system
max. 1x per system
I
Fujitsu PRIMERGY Server
17 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
I
VI
Section
Hard disks drives
Modular Raid controller is connected to internal HDDs
For basic units V1xx up to 6 SAS 3.5" hard disks can be configured also in mixed configuration.
If the option "Tape drive" is configured only 4 bays for hard disks are available
Mixed configurations with Eco SATA drives and SAS drives are not allowed
3.5" SAS drives and 3.5" BC SATA drives can be mixed, but not used in one logical RAID volume
*) SSD Mainstream Endurance 10DWPD over 5y
SATA Disk Drive 3.5"
HDD SATA 6Gb/s 3.5" with hot plug/hot replace tray
500GB 7200rpm,<9,0ms, 64MB Cache
1TB 7200rpm,<9,0ms, 64MB Cache
2TB 7200rpm,<9,0ms, 64MB Cache
3TB 7200rpm,<9,0ms, 64MB Cache
4TB 7200rpm,<9,0ms, 64MB Cache
6x / 4x with
Backup drive for
basic unit V1xx
S26361-F3670-E500
S26361-F3670-E100
S26361-F3670-E200
S26361-F3670-E300
S26361-F3670-E400
max. 6x per System
SAS Disk Drive 3.5"
HDD SAS 6Gb/s 3.5" with hot plug/hot replace tray
300GB 15000rpm,<4,0ms, 16MB Cache
450GB 15000rpm,<4,0ms, 16MB Cache
600GB 15000rpm,<4,0ms, 16MB Cache
S26361-F4005-E530
S26361-F4005-E545
S26361-F4005-E560
1TB 7200rpm,<9,0ms, 32MB Cache
2TB 7200rpm,<9,0ms, 32MB Cache
3TB 7200rpm,<9,0ms, 32MB Cache
4TB 7200rpm,<9,0ms, 32MB Cache
S26361-F5241-E100
S26361-F5241-E200
S26361-F5241-E300
S26361-F5241-E400
max. 6x per System
Solid State Disk Drive 3.5", Mainstream Endurance*
SSD SATA 6Gb/s 2.5" within 3.5" hot plug/hot replace tray
100GB, Mainstream Performance
200GB, Mainstream Performance
400GB, Mainstream Performance
800GB, Mainstream Performance
SSD SAS 12Gb/s 2.5" within 3.5" hot plug/hot replace tray
200GB, Enterprise Performance
400GB, Enterprise Performance
800GB, Enterprise Performance
1.6TB, Enterprise Performance
max. 6x per System
S26361-F5319-E100
S26361-F5319-E200
S26361-F5319-E400
S26361-F5319-E800
3.5" config: no SAS 3.0 support
S26361-F5315-E200
S26361-F5315-E400
S26361-F5315-E800
S26361-F5315-E160
as soon as available
as soon as available
as soon as available
as soon as available
J
Fujitsu PRIMERGY Server
18 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
J
Solid State Disk 2.5", Mainstream Endurance*
SSD SATA 6Gb/s 2.5" with hot plug/hot replace tray
100GB MLC, Mainstream Performance
200GB MLC, Mainstream Performance
400GB MLC, Mainstream Performance
100GB, Mainstream Performance
200GB, Mainstream Performance
400GB, Mainstream Performance
800GB, Mainstream Performance
S26361-F5225-E100
S26361-F5225-E200
S26361-F5225-E400
S26361-F5303-E100
S26361-F5303-E200
S26361-F5303-E400
S26361-F5303-E800
as long as stock
as long as stock
as long as stock
SSD SAS 6Gb/s 2.5" with hot plug/hot replace tray
100GB MLC, Enterprise Performance
200GB MLC, Enterprise Performance
S26361-F4581-E100
S26361-F4581-E200
as long as stock
as long as stock
max. 8/12/16x per system
Solid State Disk Drive, Mainstream Endurance*
SSD SAS 12Gb/s 2.5" with hot plug/hot replace tray
200GB, Enterprise Performance
400GB, Enterprise Performance
800GB, Enterprise Performance
1.6TB, Enterprise Performance
max. 8/12/16x per system, max. 8x 12Gb/s support
S26361-F5297-E200
S26361-F5297-E400
S26361-F5297-E800
S26361-F5297-E160
Interface SAS12Gb/s and SAS 6Gb/s.
SAS 12Gb/s support only with PRAID
EP400i (Cougar4), *F5243-E1
and max. 8x per System
SAS Disk Drive 2.5"
max 8x for V2xx,
12x for V3xx,
16x for V4xx
HDD SAS 6Gb/s 2.5" with hot plug/hot replace tray
300GB 10000rpm,<4,5ms, 32MB Cache
450GB 10000rpm,<4,5ms, 32MB Cache
600GB 10000rpm,<4,5ms, 32MB Cache
900GB 10000rpm,<4,5ms, 32MB Cache
1,2TB 10000rpm,<4,5ms, 64MB Cache
S26361-F5247-E130
S26361-F5247-E145
S26361-F5247-E160
S26361-F5247-E190
S26361-F5247-E112
146GB 15krpm,<4,5ms, 16MB Cache
300GB 15krpm,<4,5ms, 32MB Cache
S26361-F4482-E514
S26361-F4482-E530
500GB 7.2krpm,<9,5ms, 64MB Cache
1TB 7.2krpm,<9,5ms, 64MB Cache
max. 8/12/16x per system
S26361-F5228-E500
S26361-F5228-E100
SATA Disk Drive 2.5"
HDD SATA 6Gb/s 2.5" with hot plug/hot replace tray
250GB 7.2krpm,<9,5ms, 64MB Cache
500GB 7.2krpm,<9,5ms, 64MB Cache
1TB 7.2krpm,<9,5ms, 64MB Cache
max. 8/12/16x per system
S26361-F3708-E250
S26361-F3708-E500
S26361-F3708-E100
S26361-F3837-L64
SATA DOM 64GB, 3G, Maintream Endurance, non-hot plug
Special Release
PCIe SSD (occupies one PCIe slot)
S26361-F4522-E351
PCIe-SSD 365GB MLC
ioDrive2 365GB
PCIe 2.0
25nm Lithography
PCIe x4, Low Profile
max. 2x per system
max. 2x
S26361-F4522-E781
PCIe-SSD 785GB MLC
ioDrive2 785GB
PCIe 2.0
25nm Lithography
PCIe x4, Low Profile
max. 2x per system
S26361-F4522-E121
PCIe-SSD 1.2TB MLC
ioDrive2 1.2TB
PCIe 2.0
25nm Lithography
PCIe x4, Low Profile
max. 2x per system
loose delivery: S26361-F4522-L351/L781/L121
K
Fujitsu PRIMERGY Server
19 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
K
VII
Section
Modular Raid 0/1, Raid5 for SAS or SATA HD`s. On-board Controller for max. 4x 2.5" SATA or SAS HD`s
On board SATA Controller with 3 Gb/sec and up to 4x 2.5" SATA HDDs (no additional controller required)
For up to 4x 2.5" SAS HDDs with RAID 0/1 functionality a Patsburg Upgrade Kit is required
For all other HDD configurations a modular RAID-controller is required
Following optional onboard SAS RAID can be selected for 4x2.5" HDDs or one SAS Tape device
S26361-F3674-E1
Onboard 4 port SAS Controller
LSI
Patsburg B
RAID 0, 1 & 10
no controller cache
SAS 1.0 (3Gb/sec)
4 internal ports
PCIe x4
no PCI slot required
max. 1x per system
For more than 4 hard disks or 6 Gb/sec one of the following modular RAID-controllers is required
Modular Raid 0/1 controller with IME support for SAS/SATA
This RAID controller supports max. 8 HDDs on internal SAS ports
Modular Raid 5 controller for SAS/SATA
RAID levels 0, 1, 10, 5, 50, 6 and 60
are supported.
This RAID controller supports max. 16 HDDs
combined with internal SAS expander
The FBU is an option for the controller
which can be used once per controller.
If the FBU option has been choosen, the
TFM Module is needed once per FBU.
S26361-F3554-E8
RAID Ctrl SAS 6G 8port internal
Based on chip LSISAS2008
LSI MegaRAID
no Cache, no BBU
RAID 0, 1 & 10
S26361-F3554-E512
RAID Ctrl SAS 6G 8port internal
Based on chip LSISAS2108
LSI MegaRAID
512MB Cache with ECC
RAID 0, 1, 10, 5, 50, 6, 60
S26361-F3669-E4
RAID Ctrl SAS 6G 8port internal
Based on chip LSISAS2208
LSI MegaRAID
1GB Cache with ECC
RAID 0, 1, 10, 5, 50, 6, 60
Support for 3Gb/s and 6Gb/s
optional BBU
optional FBU
SATA and SAS hard drives
PCIe x8
Low-profile MD2 form factor
max. 1x per system
Support for 3Gb/s and 6Gb/s
SATA and SAS hard drives
PCIe x8
Low-profile MD2 form factor
max. 1x per system
Support for 3Gb/s and 6Gb/s
SATA and SAS hard drives
PCIe 3.0 x8
Low-profile MD2 form factor
max. 1x per system
S26361-F3257-E216
Cache Battery Backup Unit
with 16 cm cable set
max. 1x per Controller
S26361-F3669-E660
RAID Advanced Software Options
License Activation Key
for CacheCade 2.0 and FastPath
for 1 Controller
1x
Lose delivery options
S26361-F3669-E100
S26361-F3669-L660
RAID Advanced Software Options
License Activation Key
for CacheCade 2.0 and FastPath
for 1 RAID Ctrl S26361-F3669-xx
S26361-F3669-L100
TFM Module for FBU option
TFM Module for FBU option
(flash and FBU control logic)
max. 1x per Controller
max. 1x per Controller
S26361-F3669-E125
S26361-F3669-L110
Flash Backup Unit
with 25cm, 55cm, 70cm cable set
max. 1x per Controller
Flash Backup Unit
with 25cm cable set
max. 1x per Controller
L
Fujitsu PRIMERGY Server
20 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
L
SAS-/SCSI-/ Fibre-Channel Controller Low Profile
SAS controller for external backup drives or JBOD subsystems (as soon as available)
S26361-F3628-E201
SAS Controller 6Gb/s 8 port LP
LSI SAS9200-8e LP
PCIe 2.0 x4,
ext: 8 port
max. 3x/2x per system
A combination of Emulex and Qlogic
FC / FCoE controller is not supported
All controllers for the connection of external
storage system are delivered without cables.
For the configuration of external cabling see
the configurator for external storage system.
Fibre Channel Controller for external storage systems
For Fibre Channel SAN also other componets like
S26361-F3631-E201
S26361-F3631-E202
switches, SFPs and optical wires are orderable
8GBit/s FC Controller
8GBit/s FC Controller
(for details see price liste)
Qlogic
Qlogic
QLE2560, low profile bracket
QLE2562, low profile bracket
loose delivery:
1 channel 8GBit/sec FC Contr.
2 channel 8GBit/sec FC Contr.
Single channel
S26361-F3631-L201
LC Interface for 50µm Fiber
LC Interface for 50µm Fiber
Dual Channel
S26361-F3631-L202
PCIe2 x8, 170mm
max. 6x per system
PCIe2 x8, 170mm
max. 6x per system
with mounted LP bracket
as soon as available
S26361-F5313-E201
as soon as available
S26361-F5313-E202
16GBit/s FC Controller
16GBit/s FC Controller
Qlogic
Qlogic
QLE2670, low profile bracket
QLE2672, low profile bracket
loose delivery:
1 channel 16GBit/sec FC Contr.
2 channel 16GBit/sec FC Contr.
Single channel
S26361-F5313-L501
LC Interface for 50µm Fiber
LC Interface for 50µm Fiber
Dual Channel
S26361-F5313-L502
PCIe3 x8, 170mm
max. 6x per system
PCIe3 x8, 170mm
max. 6x per system
contains LP and FH brackets.
S26361-F3961-E201
S26361-F3961-E202
8GBit/s FC Controller
8GBit/s FC Controller
Emulex
Emulex
LPe1250, low profile bracket
LPe12002, low profile bracket
loose delivery:
1 channel 8GBit/sec FC Contr.
2 channel 8GBit/sec FC Contr.
Single channel
S26361-F3961-L201
LC Interface for 50µm Fiber
LC Interface for 50µm Fiber
Dual Channel
S26361-F3961-L202
PCIe2 x8, 170mm
max. 6x per system
PCIe2 x8, 170mm
max. 6x per system
with mounted LP bracket
S26361-F4994-E201
16GBit/s FC Controller
Emulex
LPe16000, low profile bracket
1 channel 16GBit/sec FC Contr.
LC Interface for 50µm Fiber
PCIe3 x8, 170mm
max. 6x per system
S26361-F4994-E202
16GBit/s FC Controller
Emulex
LPe16002, low profile bracket
2 channel 16GBit/sec FC Contr.
LC Interface for 50µm Fiber
PCIe3 x8, 170mm
max. 6x per system
FH bracket is not included
6x
FH bracket is not included
loose delivery:
Single channel
S26361-F4994-L501
Dual Channel
S26361-F4994-L502
contains LP and FH brackets.
M
Fujitsu PRIMERGY Server
21 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
M
SAS RAID controller for JBOD subsystems
S26361-F3713-E203
RAID Ctrl SAS 6G 8port external
LSI MegaRAID SAS 9286CV-8e
1GB Cache with ECC
RAID 0, 1, 5, 6, 10, 50 & 60
without FBU
SAS 6Gb/sec
8 port external
Lose delivery options
BBU/FBU max. 2x per system possible
PCIe x8, MD2 form factor
low profile bracket
max. 4x per system
S26361-F3669-E125
S26361-F3669-L110
Flash Backup Unit
Flash Backup Unit
with 25cm cable set
with 25, 55, 70 cable set
max. 1x per Controller
max. 1x per Controller
S26361-F3669-L661
S26361-F3669-E661
RAID Advanced Software Options
RAID Advanced Software Options
License Activation Key
License Activation Key
for CacheCade 2.0 and FastPath
for CacheCade 2.0 and FastPath
for 1 RAID Ctrl S26361-F3713-xxx
for 1 Controller
N
Fujitsu PRIMERGY Server
22 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
N
VIII
Section
Raid Controller and Devices for SAS3.0 (12 Gb/sec)
Modular Raid 5 controller for SAS 12GB/s
RAID levels 0, 1, 10, 5, 50, 6 and 60
are supported.
This RAID controller supports max.
8 HDDs or SSDs
A 12GB/s SAS expander is not available!
Note: This option is possible for:
The FBU is an option for the controller
which can be used once per controller.
If the FBU option has been choosen, the
TFM Module is needed once per FBU.
Config 10: 4x SAS2.0 + 8x SAS3.0
Config 12: 3.5" drive + 8x SAS3.0
Config 15: LTO + 8x SAS3.0
S26361-F5243-E1
PRAID EP400i
Based on chip LSISAS3108
LSI MegaRAID
1GB Cache with ECC
RAID 0, 1, 10, 5, 50, 6, 60
S26361-F5243-E2
PRAID EP420i
Based on chip LSISAS3108
LSI MegaRAID
2GB Cache with ECC
RAID 0, 1, 10, 5, 50, 6, 60
optional FBU
optional FBU
Support for 3Gb/s, 6Gb/s and 12Gb/s
SATA and SAS hard drives
PCIe 3.0 x8
Low / High profile ex factory
max. 1x per system
Support for 3Gb/s, 6Gb/s and 12Gb/s
SATA and SAS hard drives
PCIe 3.0 x8
Low / High profile ex factory
max. 1x per system
S26361-F1373-E572
S26361-F1373-E550
S26361-F1373-E560
Controller supports OOB-RAID including OOB-HDD monitoring
no OOB-HDD cable needed
loose delivery: S26361-F5243-L1 / L2
Loose delivery TFM option
S26361-F5243-E100
for EP400i
TFM Module for FBU option
(flash and FBU control logic)
max. 1x per Controller
1x
S26361-F5243-E125
Flash Backup Unit
with 25cm cable set
max. 1x per Controller
S26361-F5243-E200
for EP420i
TFM Module for FBU option
(flash and FBU control logic)
max. 1x per Controller
The FBU is an option
which can be used once per controller.
If the FBU option has been choosen, the
TFM Module is needed once per FBU.
S26361-F5243-L100 / L200
TFM Module for FBU option
(flash and FBU control logic)
max. 1x per Controller
S26361-F5243-L110
Flash Backup Unit
with 25cm, 55cm, 70cm cable set
max. 1x per Controller
Advanced Software Option
S26361-F5243-E660
RAID Advanced Software Options
License Activation Key
for CacheCade 2.0 and FastPath
for 1 Controller
S26361-F5243-L660
RAID Advanced Software Options
License Activation Key
for CacheCade 2.0 and FastPath
for 1 Controller
O
Fujitsu PRIMERGY Server
23 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
O
X
Section
Communication / Network
2x Gigabit (Dualport) Ethernet Contr.
onboard
Intel LAN I350 (Powerville)
ext: 2x RJ 45 connector
Modular On-Board LAN is a flexible extension of a cost-optimized Motherboard
with basic 2x Gbit LAN on-board.
5 different Upgrade-Kits are offered, which occupies a dedicated PCIe slot and
can be ordered once per system.
If a 1Gb modular LAN Controller is installed, 3 additional 1Gb LAN controllers are possible!
If a 10Gb modular LAN Controller is installed, 2 additional 10Gb LAN controllers is possible!
1Gbit/s Modular On-Board LAN Adapter
S26361-F4610-E802
Upgrade-Kit to 4x 1Gb LAN on-board LP
PLAN CP 2x1Gbit Cu Intel I350-T2 LP
Intel Powerville based 2 port Server Ad.
PCIe x4, Low Profile
ext: for RJ45-plug, Cat 5
max. 1x per system
4x
S26361-F4610-E804
Upgrade-Kit to 6x 1Gb LAN on-board LP
PLAN CP 4x1Gbit Cu Intel I350-T4 LP
Intel Powerville based 4 port Server Ad.
PCIe x4, Low Profile
ext: for RJ45-plug, Cat 5
max. 1x per system
S26361-F3629-E702
Upgrade-Kit to 2xGbit+2x10Gbit LOM
Eth Ctrl 2x10Gbit PCIe x8 D2755 SFP+
Intel Niantic based dual port 10Gb NIC
please refer to 10Gb LAN section
S26361-F4610-E204
(I350-T4)
Gbit Ethernet Controller Quad 1000TX LP
PLAN CP 4x1Gbit Cu Intel I350-T4 LP
Intel Powerville based 4 port Server Ad.
PCIe x4, Low Profile
low profile (LP) bracket
ext: for RJ45-plug, Cat 5
max. 4x per system
S26361-F3516-E201
(Shelter Island)
Gigabit Ethernet Controller 1000TX LP
Eth Ctrl 1x1Gbit PCI-e Gigabit CT DT Cu LP
Intel® Gigabit CT Desktop Adapter
PCIe x1
ext: for RJ45-connector, Cat 5
max. 4x per system
1Gbit/s Ethernet Adapter
S26361-F4610-E202
(I350-T2)
Gbit Ethernet Controller Dual 1000TX LP
PLAN CP 2x1Gbit Cu Intel I350-T2 LP
Intel Powerville based 2 port Server Ad.
PCIe x4, Low Profile
low profile (LP) bracket
ext: for RJ45-plug, Cat 5
max. 4x per system
Loose delivery with FH and LP bracket:
I350-T2
S26361-F4610-L502
I350-T4
S26361-F4610-L504
Loose delivery with LP bracket:
Shelter Island
S26361-F3516-L201
Sheepshead Bay S26361-F3242-L201
6x
P
Fujitsu PRIMERGY Server
24 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
P
If a 10Gb modular LAN Controller is installed, 1 additional 10gb LAN controllers is possible!
10Gbit/s
Ethernet
10GbE
2-Port
SFP+Adapter
for MMF Module
S26361-F3629-E702
(D2755)
Upgrade-Kit to 2xGbit+2x10Gbit LOM
Eth Ctrl 2x10Gbit PCIe x8 D2755 SFP+
Intel Niantic based dual port 10Gb NIC
PCIe x8, Low Profile, Low Profile Bracket
ext: 2x SFP+ cage
max. 1x per system
S26361-F3629-E202
(D2755)
10 Gigabit Ethernet Contr. dual port SFP+
Eth Ctrl 2x10Gbit PCIe x8 D2755 SFP+
Intel Niantic based dual port 10Gb NIC
PCIe x8, Low Profile, Low Profile Bracket
ext: 2x SFP+ cage
max. 2x per system
S26361-F3752-E202
(Intel X540-T2)
Eth Ctrl 2x10GBase-T lp
Intel Twinville based 2 port Server Ad.
PCIe x4, Low Profile
low profile (LP) bracket
ext: for RJ45-plug, Cat 6
max. 2x per system
S26361-F3629-E750
Shared 10Gb Management LAN
Install and configure Management
LAN on 10Gb Shared LAN port
max. 1x per 10Gb upgrade kit
S26361-F3986-E3
SFP+ Module MMF 10GbE LC
SFP+ module for 10 Gbit
S26361-F3986-E4
SFP+ Module SMF 10GbE LC
SFP+ module for 10 Gbit
Ethernet 50µm FO cabling
ext:LC-SR-connector
max. 2x per controller
Ethernet 9µm FO cabling
ext:LC-LR-connector
max. 2x per controller
V:TWX Connector-PY
for all Twinax (FTS,BR,CI)
max. 2x per controller
The SFP+ modules are also available as loose delivery
S26361-F3986-L3
S26361-F3986-L4
Instead SFP+ Modules, SFP+ twinax cables from the switch vendors may be used
S26361-F3989-E600 *)
S26361-F3873-E500 *)
S26361-F4571-E500 *)
*) in SA only
SFP+ active twinax cable
SFP+ active twinax cable
SFP+ passive twinax cable
shown in
customized twinax cable for
customized twinax cable for
customized twinax cable for
cabling view
full rack setup ex factory
full rack setup ex factory
full rack setup ex factory
cable length is selected by
cable length is selected by
cable length is selected by
requirement in the factory
requirement in the factory
requirement in the factory
Fujitsu branded cable
max. 2x per controller
Brocade branded cable
max. 2x per controller
Cisco branded cable
max. 2x per controller
separate orderable 10Gb Ethernet cables
S26361-F3989-L102
SFP+ active Twinax Cable Fujitsu 2m
The controller D2755 is delivered without SFP+ modules for optical
S26361-F3989-L105
SFP+ active Twinax Cable Fujitsu 5m
cables, these must be ordered separately.
S26361-F3989-L110
SFP+ active Twinax Cable Fujitsu 10m
Loose delivery options (FH and LP bracked included)
S26361-F3873-L501
SFP+ active Twinax Cable Brocade 1m
D2755
S26361-F3629-L502
S26361-F3873-L503
SFP+ active Twinax Cable Brocade 3m
X540-T2
S26361-F3752-L502
S26361-F3873-L505
SFP+ active Twinax Cable Brocade 5m
S26361-F4571-L101
SFP+ passive Twinax Cable Cisco 1m
S26361-F4571-L103
SFP+ passive Twinax Cable Cisco 3m
S26361-F4571-L105
SFP+ passive Twinax Cable Cisco 5m
S26361-F4571-L107
SFP+ active Twinax Cable Cisco 7m
S26361-F4571-L110
SFP+ active Twinax Cable Cisco 10m
R
Fujitsu PRIMERGY Server
25 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
R
G) Fibre Channel over Ethernet
while stocks last
S26361-F3592-E202
10GBit/s CNA
Emulex
OCe10102
2 channel 10GBit/sec CNA
SFP+ Cage
PCIe x8, 170mm
max. 4 per system
S26361-F5250-E201
10GBit/s CNA
Emulex
OCe14102
2 channel 10GBit/sec CNA
SFP+ Cage
PCIe x8, 170mm
max. 4 per system
S26361-F3592-E108
SFP+ Module MMF 10GbE LC
SFP+ module for 10 Gbit
Ethernet FO cabling
ext:LC-connector
max. 2x per adapter
4x
A mix of OCe10102 and OCe14102 is
not supported
The controller is delivered without SFP+
modules for optical cables, these must be
ordered separately. Without SFP+ modules
copper twinax cables are supported.
S26361-F5250-E110
SFP+ Module MMF 10GbE LC
SFP+ module for 10 Gbit
Ethernet FO cabling
ext:LC-connector
max. 2x per adapter
Controllers are also available as loose delivery
OCe10102
S26316-F3592-L202
OCe14102
S26361-F5250-L501
contains FH and LP bracket
SFP+ modules are also available as loose delivery
V:TWX Connector-PY
for all Twinax (FTS,BR,CI)
max. 2x per adapter
for OCe10102
for OCe14102
S26316-F3592-L108
S26361-F5250-L110
S26361-F3989-E600 *)
S26361-F3873-E500 *)
S26361-F4571-E500 *)
*) in SA only
SFP+ active twinax cable
SFP+ active twinax cable
SFP+ passive twinax cable
shown in
customized twinax cable for
customized twinax cable for
customized twinax cable for
cabling view
full rack setup ex factory
full rack setup ex factory
full rack setup ex factory
cable length is selected by
cable length is selected by
cable length is selected by
requirement in the factory
requirement in the factory
requirement in the factory
Fujitsu branded cable
max. 2x per controller
Brocade branded cable
max. 2x per controller
Cisco branded cable
max. 2x per controller
separate orderable 10Gb Ethernet cables
S26361-F3989-L102
SFP+ active Twinax Cable Fujitsu 2m
S26361-F3989-L105
SFP+ active Twinax Cable Fujitsu 5m
S26361-F3989-L110
SFP+ active Twinax Cable Fujitsu 10m
S26361-F3873-L501
SFP+ active Twinax Cable Brocade 1m
S26361-F3873-L503
SFP+ active Twinax Cable Brocade 3m
S26361-F3873-L505
SFP+ active Twinax Cable Brocade 5m
S26361-F4571-L101
SFP+ passive Twinax Cable Cisco 1m
S26361-F4571-L103
SFP+ passive Twinax Cable Cisco 3m
S26361-F4571-L105
SFP+ passive Twinax Cable Cisco 5m
S26361-F4571-L107
SFP+ active Twinax Cable Cisco 7m
S26361-F4571-L110
SFP+ active Twinax Cable Cisco 10m
H) InfiniBand HCA's
S26361-F4475-E122/E222
PIB EP QLE7340e/42e
Intel IB HCA 1x / 2x 40Gb
PCIe 2.0 (5,0GT/s)
PCIe x8, low profile
ext: 1x / 2x QSFP-connector
max. 2x per system
S26361-F4475-E103/E203
IB HCA 40Gb
1 and 2 port QDR enhanced
IB HCA 1x / 2x 40Gb
PCIe 3.0 (8,0GT/s)
PCIe x8, low profile
ext: 1x / 2x QSFP-connector
max. 2x per system
S26361-F4533-E102/E202
IB HCA 56Gb 1 and 2 port FDR
IB HCA 1x / 2x 56Gb
PCIe 3.0 (8,0GT/s)
PCIe x8, low profile
ext: 1x / 2x QSFP-connector
max. 2x per system
2x
only within a rack
configuration
S26361-F3996-E203
Intel IB Cu Cable 40Gb
S26361-F3996-E210
Intel IB FO Cable 40Gb
QSFP, 3m
max. 2x per adapter
QSFP, 10m
max. 2x per adapter
loose delivery: S26361-F4475-L122/L222
loose delivery: S26361-F4475-L103/L203
loose delivery: S26361-F4533-L102/L202
Loose delivery with
FH and LP bracket included
Copper cable are also available for loose
delivery as
S26361-F3996-L203, QSFP, 40Gb, 3m
S26361-F3996-L210, QSFP, 40Gb, 10m
S26361-F3996-E556
InfiniBand Cu Cable 56Gb
customized
QSFP, 1m and 3m
max. 2x per adapter
For the US market only:
Due to EMI restrictions, only one IB FDR HCA
might be installed per system
If additional length of copper cable or optical cable are needed,
then they must be ordered from the cable vendor directly
Copper cable are also available for loose delivery as
S26361-F3996-L561, QSFP, 56Gb, 1m
S26361-F3996-L563, QSFP, 56Gb, 3m
S
Fujitsu PRIMERGY Server
26 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
S
XI
Section
System Management Products (RemoteView)
iRMC S4 (integrated Remote Management Controller) onboard server management
Controller with dedicated 10/100/1000 Service LAN-port and integrated graphics.
S26361-F1790-E243
iRMC S4 advanced pack
integrated remote management controller
activation key for
graphical console redirection
and remote media redirection
max. 1x per system
S26361-F2557-E106
Local Service Display incl. mount. kit
Customer Self Service
LSD module incl. mounting kit
0.5" x 5.25"
max. 1x per system
available April 2014
S26361-F1373-E540
HDD&RAID OOB monitoring by iRMC
Out of Band Status Monitoring for HDD
This option enables the out-of-band monitoring function of the HDD by iRMC.
w/o OS running
Cables and 2x HDD BP for 8x 2.5" HDDs
In this case HDD will be monitored without any Server Management agents.
Not necessary for: RAID Ctrl SAS 6G 1GB (D3116C)
max. 1x per system
Note: This option is possible for S26361-K1457-V401 only!
S26361-F2571-E27
Maintenance LAN
Front management LAN Port
In combination with iRMC adv. pack
For local maintenance / console redirection,
Integrated in front (operating panel)
max. 1x per system
XII
Section
Miscellaneous
Options and other peripherals
For other options, refer to SystemArchitect and Pricelist
These options are supplied lose with the shipment
For suitable peripherals for this product, please refer to SystemArcitect
Cool-safe ATD configuration restrictions for RX300S8:
S26361-F3776-E101
Cool-safe® Advanced Thermal Design
related L-numbers as well restricted
Restricts configuration to make
Cache Battery Backup Unit
5-40° possible
no tape drives
Feature is enabled and fixed ex factory
Tape drive LTO4 HH SAS IBM V2
S26361-F3626-E2
max. 1x per system
Tape drive LTO5HH Ultrium SAS
S26361-F3627-E1
Tape drive LTO6HH Ultrium SAS
S26361-F3787-E1
no BBU
S26361-F3257-E216
no PCIe SSDs
PCIe-SSD 365GB MLC
S26361-F4522-E351
PCIe-SSD 785GB MLC
S26361-F4522-E781
PCIe-SSD 1.2TB MLC
S26361-F4522-E121
no 130W CPUs
Xeon E5-2690v2 10C/20T 3.00GHz 25MB 8.00GT/s 1866MHz 130W
S26361-F3790-E300
Xeon E5-2637v2 4C/8T 3.50GHz 15MB 8.00GT/s 1866MHz 130W
S26361-F3791-E350
Xeon E5-2643v2 6C/12T 3.50GHz 25MB 8.00GT/s 1866MHz 130W
S26361-F3791-E330
Xeon E5-2667v2 8C/16T 3.30GHz 25MB 8.00GT/s 1866MHz 130W
Xeon E5-2697v2 12C/24T 2.70GHz 30MB 8.00GT/s 1866MHz 130W
S26361-F3791-E300
S26361-F3791-E270
no 32GB LRDIMM @ 1866 MHz
32GB (1x32GB) 4Rx4 DDR3-1866 LR ECC
S26361-F3848-E517
T
Fujitsu PRIMERGY Server
27 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
T
XIII
Section
Country specific power cord
S26361-F1452-E100
S26361-F1452-E110
S26361-F1452-E130
REGION KIT APAC/EMEA/India
For Shipments to Asia pacific,
EMEA or India regions
1x per system
REGION KIT JP
For Shipments to Japan regions
REGION KIT America
For Shipments to America
1x per system
1x per system
For shipments to India mandatory!
S26361-F3301-E123
Certification for India
Hint: No country specific powercord configurable with Certification for India and China (CCC)
Power cord options (1x per PSU)
max.
2x
T26139-Y1968-E100
Powercord for rack, 4m, grey,
IEC 320 C14 connector
T26139-Y1742-E10
USA, Canada, 1.8m, grey
T26139-Y4024-E10
for -48V DC PSU only, 4m, black
T26139-Y3850-E10
Option "no powercord", for Countries without
specific cable orderable like e.g. China
U
Fujitsu PRIMERGY Server
28 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
U
Section
XVI
CCC exclusions
S26361-F3301-E120
CCC Certification for China
Limits configuration in accordance
with CCC exclusions
max. 1x per system
The following order components out of the specific sections
are NOT allowed together with CCC Certification for China:
Front-VGA Interface
S26361-F2571-E26
PCIe-SSD 365GB MLC
PCIe-SSD 785GB MLC
PCIe-SSD 1.2TB MLC
S26361-F4522-E351
S26361-F4522-E781
S26361-F4522-E121
SAS Ctrl 6G 8ext PCIe lp
S26361-F3628-E201
Shared 10Gb Management LAN Kit
S26361-F3629-E750
Modulare SV 800W titanium hp
Modulare SV DC -48V 800W gold hp
Cable powercord rack, 4m, grey
Ltg Netzanschluss -48V DC, 4m, schwarz
Leitung Netzanschluss (USA), 1,8m, grau
S26113-F615-E10
S26113-F609-E10
T26139-Y1968-E100
T26139-Y4024-E10
T26139-Y1742-E10
TPM Modul
S26361-F3552-E1
End PRIMERGY RX300 S8
Fujitsu PRIMERGY Server
29 of 30
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2014-09-30
Change Report
Date
Order number
Changes
2014-08-04
S26361-F5313-xxx
16Gb Qlogic added
2014-07-03
2014-07-02
2014-06-30
2014-06-16
2014-06-16
2014-06-16
2014-06-10
2014-05-19
2014-05-06
2014-05-02
2014-04-03
2014-03-18
2014-03-17
2014-03-17
2014-03-17
2014-03-05
2014-01-30
2014-01-30
2013-12-12
2013-11-29
2013-11-27
2013-10-28
2013-10-28
2013-10-18
2013-10-16
2013-10-09
2013-10-08
2013-09-19
2013-09-13
2013-09-03
2013-09-01
S26361-F5315-E*
S26361-F3848-E517
S26361-F3301-E123
S26361-F3740-xxx
S26361-F3739-xxx
S26361-F3242-E201 / -L201
S26361-F5319-E*
S26361-F3848-E517
S26361-F53250
Added 3.5" SAS 12G SSDs
No ATD functionality with 32GB LRDIMM @ 1866 MHz
S26361-F3776-E101
Cool-safe ATD restriction changed - 32GB and 64GB LRDIMM no more restricted
SAS3.0 RAID Ctrl updated
phase out
phase out
EOL
HDD&RAID OOB monitoring by iRMC added
New SATA SSDs added.
New SAS 12G SSDs added.
restricted for ATD
SATA DOM (Disk on module) added
S26361-F3739-E201
S26361-F3740-E201
S26361-F3610-E202
S26361-F1373-E540
S26361-F5303-*
S26361-F5297-*
S26361-F3554-E8
S26361-F3837-L64
S26361-F3301-E120
Added certification for India
EOL
EOL
EOL
Added 3.5" SATA 6G SSDs
Added 32 GB LRDIMM 1866 MHz
new CNA OCe14102 added
PCIe SSD SFF options removed
Restrictions CCC Certification for China updated
SSD support with On-Board controller.
restriction for 2.5" BC-SAS HDD with "*F3554-E8" removed.
optional USB Comps
S26361-F4610-E202 / -E204
no longer available
added new 1Gb NICs from Intel
S26113-F615-E10
add comment "110V range not supported"
restrictions for Cool-safe ATD added
Memory hint on CPU page extended
S26361-F5247-E112
RMK
HDD 1.2TB SAS 10K added.
CMA not longer a must component
First Release
Fujitsu PRIMERGY Server
30 of 30
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising