JVC XV-SA602SL User Guide Manual Operating Instruction Pdf

JVC XV-SA602SL User Guide Manual Operating Instruction Pdf
DVD AUDIO/VIDEO PLAYER
XV-SA600BK/XV-SA602SL
TV
2
Getting started
6
Basic operations
14
Advanced operations
26
MP3 disc playback
47
JPEG disc playback
51
Changing the initial settings
56
Additional information
69
DVD
STANDBY/ON
OPEN/
CLOSE
TV
TV1
DVD
TV2
1
2
TV4
TV5
TV3
3
4
5
TV7
TV8
TV6
6
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
PAGE
RETURN
T
Introduction
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
N
STROBE
SLOW-
DVD AUDIO/DVD VIDEO/SUPER VCD/VCD/CD PLAYER
SLOW+
0 OPEN/CLOSE
REPEAT SUB TITLE AUDIO
7 STOP
3 PLAY
8 PAUSE
4
SKIP
¢
VFP
STANDBY/ON
fs/Rate PROGRESSIVE
SCAN
DIGEST
3D
PHONIC
ANGLE
ZOOM
STANDBY/ON
AMP VOL
PROGRESSIVE DVD AUDIO
RM-SXV011J
REMOTE CONTROL
INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial No.
which are located on the rear, bottom or
side of the cabinet. Retain this information
for future reference.
Model No.
Serial No
LET0205-001A
[J/UJ]
Downloaded From DvDPlayer-Manual.com JVC Manuals
Warnings, Cautions and Others
Mises en garde, précautions et indications diverses
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended
toalert the user to the presence of
uninsulated “dangerous voltage” within the
product's enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
For U.S.A.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
For Canada/pour le Canada
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS
LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQUAU FOND
For Canada/pour le Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS
B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL
APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING
EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS”,
ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE
BRUITS
RADIOELECTRIQUES
APPLICABLES
AUX
APPAREILS NUMERIQUES DE CLASSE B PRESCRITES
DANS LA NORME SUR LE MATERIEL BROUILLEUR:
“APPAREILS NUMERIQUES”, NMB-003 EDICTEE PAR LE
MINISTRE DES COMMUNICATIONS.
Downloaded From DvDPlayer-Manual.com JVC Manuals
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret
de l’appareil.
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.
Caution –– STANDBY/ON
button!
Disconnect the mains plug to shut the power off completely (the
STANDBY/ON lamp goes off). The STANDBY/ON
button in
any position does not disconnect the mains line.
• When the unit is on standby, the STANDBY/ON lamp lights red.
• When the unit is turned on, the STANDBY/ON lamp lights
green.
The power can be remote controlled.
Attention –– Commutateur STANDBY/ON
!
Déconnectez la prise d’alimentation secteur pour mettre l’appareil
complètement hors tension (le témoin STANDBY/ON
s’éteint). L’interrupteur STANDBY/ON
, sur n’importe quelle
position, ne peut pas déconnecter l’appareil du secteur.
• Quand l’appareil est en mode de veille, le témoin STANDBY/
ON est allumé en rouge.
• Quand l’appareil est sous tension, le témoin STANDBY/ON est
allumé en vert.
L’alimentation peut être télécommandée.
IMPORTANT FOR LASER PRODUCTS
IMPORTANT POUR LES PRODUITS LASER
1. CLASS 1 LASER PRODUCT
2. DANGER: Visible laser radiation when open and interlock
failed or defeated. Avoid direct exposure to beam.
3. CAUTION: Do not open the top cover. There are no user
service-able parts inside the Unit; leave all servicing to
qualified service personnel.
1. PRODUIT LASER CLASSE 1
2. ATTENTION: Radiation laser visible quand l’appareil est
ouvert ou que le verrouillage est en panne ou désactivé. Eviter
une exposition directe au rayon.
3. ATTENTION: Ne pas ouvrir le couvercle du dessus. Il n’y a
aucune pièce utilisable à l’intérieur. Laisser à un personnel
qualifié le soin de réparer votre appareil.
CAUTION
• Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper or
cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted candles,
on the apparatus.
• When discarding batteries, environmental problems must be
considered and local rules or laws governing the disposal of these
batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping or
splashing and that no objects filled with liquids, such as vases,
shall be placed on the apparatus.
ATTENTION
• Ne bloquez pas les orifices ou les trous de ventilation.
(Si les orifices ou les trous de ventilation sont bloqués par un
journal un tissu, etc., la chaleur peut ne pas être évacuée
correctement de l’appareil.)
• Ne placez aucune source de flamme nue, telle qu’une bougie, sur
l’appareil.
• Lors de la mise au rebut des piles, veuillez prendre en
considération les problèmes de l’environnement et suivre
strictement les règles et les lois locales sur la mise au rebut des
piles.
• N’exposez pas cet appareil à la pluie, à l’humidité, à un
égouttement ou à des éclaboussures et ne placez pas des objets
remplis de liquide, tels qu’un vase, sur l’appareil.
English
Table of Contents
Introduction
Changing the language, sound and scene angle.......... 35
Page 2
Supplied accessories..........................................................2
Notes on handling ..............................................................3
Important cautions...................................................................3
Safety precautions ...................................................................3
About discs .........................................................................4
Playable disc types...................................................................4
Non-playable discs...................................................................4
Audio formats...........................................................................4
Disc structure............................................................................5
Video CDs and SVCDs with Playback Control function ........5
Care and handling of discs......................................................5
Getting started
Page 6
Connections ........................................................................6
Before making any connections .............................................6
To connect to a TV ...................................................................6
To connect to a stereo audio amplifier/receiver....................9
To connect to an amplifier/receiver equipped with
5.1-channel inputs.................................................................9
To connect to a digital audio device.....................................10
To connect the power cord ...................................................11
Using the remote control unit.........................................12
To install batteries in the remote control unit .....................12
Remote sensor .......................................................................12
To use the remote control unit for TV operation.................13
To control the volume of a JVC’s amplifier or receiver ......13
Basic operations
Page 14
Before operation...............................................................14
Turning on/off the unit...........................................................14
The initial setup before using the unit .................................15
Basic playback ..................................................................17
Inserting and removing discs................................................17
To start playback ....................................................................18
To stop playback completely ................................................18
To stop playback temporarily ...............................................18
Resuming playback ..........................................................19
To select the subtitle language [SUB TITLE] .......................35
To change the audio language or sound [AUDIO] ..............36
To select a scene angle of DVD VIDEO [ANGLE].................37
Special picture playback and picture/sound effect ...... 38
To display continuous still pictures [STROBE] ....................38
To zoom in/out pictures [ZOOM] ..........................................39
To adjust the picture character [VFP] ...................................39
To simulate surround sound [3D PHONIC] ..........................40
Checking the sampling frequency and bit rate............. 41
Menu bar functions ......................................................... 42
To bring up the menu bar .....................................................42
Basic operation procedure ....................................................42
Menu bar functions for DVD AUDIO ....................................43
Menu bar functions for DVD VIDEO .....................................44
Menu bar functions for SVCD/Video CD/Audio CD .............45
MP3 disc playback
Page 47
About MP3 disc................................................................ 47
Operations........................................................................ 47
Basic operations.....................................................................47
Selecting the desired Group and Track................................48
Direct selection.......................................................................49
Repeat playback .....................................................................49
Checking the sampling frequency and bit rate....................50
JPEG disc playback
Page 51
About JPEG disc .............................................................. 51
Basic operations .............................................................. 52
To see a desired picture ........................................................52
To zoom in/out the picture [ZOOM] .....................................53
To see pictures continuously [slide show mode] ......... 53
To play back pictures from the beginning of the disc.........53
Selecting the start point of the slide show ..........................54
Repeat function ......................................................................55
Changing the initial settings
Page 56
Selecting preferences...................................................... 56
To advance or reverse playback rapidly while monitoring .... 21
To advance a still picture frame-by-frame ...........................21
To play back in slow-motion .................................................21
About the Preference display................................................56
How to set preferences..........................................................56
LANGUAGE page ...................................................................57
PICTURE page ........................................................................59
AUDIO page............................................................................60
SPK.SETTING page ................................................................62
OTHERS page.........................................................................63
To locate the beginning of the scene or song ...............22
Making fine tuning for your speakers............................ 64
To locate a desired selection using 4 or ¢...................22
To locate a desired selection using the numeric buttons ...23
To set the speaker sizes.........................................................64
To set the delay time .............................................................64
To set the speaker level .........................................................65
To memorize the interrupted position .................................19
To resume playback...............................................................20
Variable speed playback ..................................................21
Other convenient functions.............................................24
To check the playback status ................................................24
To move back the playback position while DVD VIDEO
playback [One touch replay function] ...............................25
To change the brightness of the display window ...............25
Advanced operations
Page 26
Playing from a specific position on a disc......................26
To locate a desired scene from the DVD menu ...................26
To locate a desired scene from the menu of the
SVCD/Video CD with PBC...................................................26
To specify a desired title/group ............................................27
To locate a desired position in the current title,
group or track [Time search]..............................................28
To locate a desired scene from the display [DIGEST].........29
To select a still picture on a DVD AUDIO disc [PAGE] ........30
To play back a bonus group of a DVD AUDIO disc .............30
Changing the playback order ..........................................31
To play back in the desired order [Program playback] .......31
To play back in random order [Random playback] .............33
Repeat playback ...............................................................33
To repeat the current selection or all tracks
[Repeat playback]................................................................33
To repeat a desired part [A-B repeat playback] ...................34
Downloaded From DvDPlayer-Manual.com JVC Manuals
Limiting playback by children ........................................ 66
To set Parental Lock for the first time [PARENTAL LOCK].....66
To change the settings [PARENTAL LOCK] .........................67
To temporarily release the Parental Lock
[PARENTAL LOCK]..............................................................68
Additional information
Page 69
Names of parts and controls .......................................... 69
Front panel .............................................................................69
Display window......................................................................69
Rear panel...............................................................................69
Remote control unit ...............................................................70
AV COMPU LINK remote control system...................... 71
Connection and setup............................................................71
Operation ................................................................................71
Troubleshooting .............................................................. 72
Frequently Asked Questions .......................................... 74
Specifications................................................................... 75
Appendix A: Country/Area code list for Parental
Lock ................................................................................ 76
Appendix B: Glossary ...................................................... 77
Appendix C: Index............................................................ 79
1
Introduction
Supplied accessories
• R6P(SUM-3)/AA(15F) battery (x 2)
Introduction
• Audio/video cable (Yellow/White/Red) (x 1)
• AC power cord (x 1)
• Component video cable (Red/Green/Blue) (x 1)
• Audio cable (White/Red) (x 2)
• Remote Control Unit (x 1)
/
M
E E
P S
O LO
C
T
V
1
1
T
V
V
T
3
3
8
T
V
6
6
T
9
9
V
+
G
N
TI
U
M 10
/
LE UP
TITRO
G
O
E
ID EL
/V NC
TV A
C
L+
O
V
MENU
T
X
E
N
T
C
LE
E
S
E
B
O
TR
S
E
TL
TI
+
W
LO
S
FP
V
M
O
E
IV
SS
RE N
G A
O SC
PR
ate O
/R Z
fs
IO
D
U
A
LE
G
N
A
P
M
A
L
C
V
R
1J L
01 RO
V T
X ON
-S E C
M T
R EMO
2
Downloaded From DvDPlayer-Manual.com JVC Manuals
V
V
T
T
0
E
G
PA
0
V
R
E
T
N
E
S
B
SU
T
S
E
IG
D
3D NIC
O
PH
• AV compulink cable (x 1)
D
5
5
V
8
T
H
C+
H
C-
EN
V
T
--
10
-/
V
LO
V
R
P
E U
CHOIC EVIO
R
A
LE
C
W
LO
S
AT
E
P
E
R
ON
SCRE
D
T
U
N
/O D
Y V
B D
D
N
V
T
2
2
7
7
V
V
T
T
TA
S
4
4
LE
G
N
A
TOP MEN
• AC power plug adaptor (x 1)
(for PX model only)
Introduction
English
Notes on handling
Important cautions
Safety precautions
Installation of the unit
• Select a place which is level, dry and neither too hot
nor too cold (between 5oC and 35oC, 41oF and 95oF).
• Leave sufficient distance between the unit and the TV.
• Do not use the unit in a place subject to vibrations.
Avoid moisture, water and dust
Do not place the unit in moist or dusty places.
To prevent malfunction of the unit
• There are no user-serviceable parts inside. If anything
goes wrong, unplug the power cord and consult your
dealer.
• Do not insert any metallic object into the unit.
• Do not use any non-standard shape disc available on
the market, because it may damage the unit.
• Do not use a disc with tape, seals, or paste on it,
because damage to the unit may result.
Note about copyright laws
• Please check the copyright laws in your country before
recording from DVD AUDIO, DVD VIDEO, SVCD, Video
CD, Audio CD, MP3 and JPEG discs. Recording of
copyrighted material may infringe copyright laws.
Introduction
Power cord
• Do not handle the power cord with wet hands!
• A small amount of power (2.0 W, for PX model:3.4 W)
is always consumed while the power cord is connected
to the wall outlet.
• When unplugging the unit from the wall outlet, always
pull the plug, not the power cord.
Avoid high temperatures
Do not expose the unit to direct sunlight or place it near
a heating device.
When you are away
When you are away on travel or otherwise for an
extended period of time, remove the plug from the wall
outlet.
Do not insert foreign objects into the unit
Do not insert wires, hairpins, coins, etc. into the unit.
Do not block the vents
Blocking the vents may damage the unit.
Care of the cabinet
When cleaning the unit, use a soft cloth and follow the
relevant instructions on the use of chemically-coated
cloths. Do not use benzene, thinner or other organic
solvents and disinfectants. These may cause
deformation or discoloring.
If water gets inside the unit
Turn off the power and remove the plug from the wall
outlet, then call the store where you made your
purchase. Using the unit in this state may cause a fire or
electrical shock.
Note about the copyguard system
• The DVD VIDEO disc is protected by the copyguard
system. When you connect the unit to your VCR (or
integrated TV/Video system), the copyguard system
activates and the picture may not be played back
correctly.
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents
and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this
copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and
other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
Manufactured under license from Dolby Laboratories. “Dolby,” “MLP Lossless” and the double-D symbol are
trademarks of Dolby Laboratories.
Confidential unpublished works.
Copyright 1992-1998 Dolby Laboratories. All rights reserved.
Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942, 5,956,674, 5,974,380,
5,978,762, and other world-wide patents issued and pending. “DTS” and “DTS Digital Surround” are registered
trademarks of Digital Theater Systems, Inc. Copyright 1996, 2000 Digital Theater Systems, Inc. All Rights Reserved.
Downloaded From DvDPlayer-Manual.com JVC Manuals
3
Introduction
About discs
Playable disc types
Audio formats
Playable disc types are as follows:
There are some audio formats recorded on discs as
shown below.
DVD AUDIO
DVD VIDEO
VIDEO
AUDIO
Introduction
SVCD
Video CD
Audio CD
The DVD Logo is a trademark.
• CD-R and CD-RW discs recorded with the SVCD, Video
CD, Audio CD, MP3 or JPEG format can be played back,
though some may not be played back because of the
disc characteristics or recording conditions.
Note that unfinalized discs cannot be played back.
• DVD-R discs recorded with the DVD VIDEO format can
be played back, though some may not be played back
because of the disc characteristics or recording
conditions.
Note that unfinalized disc cannot be played back.
• DVD VIDEO players and DVD VIDEO discs have their
own Region Code numbers. This unit can play back
only DVD VIDEO discs whose Region Code numbers
include “1.”
Examples of playable DVD VIDEO discs:
ALL
1
15
1 2
3 4
123
456
This unit accommodates the NTSC system, also can play
back discs recorded with PAL system whose Region
Code numbers include “1.”
Note that the PAL video signal on disc is converted to an
NTSC signal and output.
Non-playable discs
Non-playable disc types are as follows:
DVD-ROM, DVD-RAM, DVD-RW, DVD+RW, CD-ROM,
PHOTO CD, CD-EXTRA, CD-G, CD-TEXT, SACD,
MIX-MODE CD
• Playing back discs listed as “Non-playable discs”
above may generate noise and damage speakers.
• This unit can play back audio signals recorded in CD-G,
CD-EXTRA, CD-TEXT and MIX-MODE CD discs.
• Linear PCM
Uncompressed digital audio, the same format used on
CDs and most studio masters.
DVD AUDIO supports up to six channels at sample
rates of 48/96/192 kHz (also 44.1/88.2/176.4 kHz) and
sample sizes of 16/20/24 bits.
DVD VIDEO supports two channels at sampling rates
of 48/96 kHz and quantization of 16/20/24 bits.
Audio CD/Video CD is limited to two channels,
44.1 kHz at 16 bits.
• Dolby Digital
A surround audio format configured with six
channels. Because the “LFE (Low-Frequency Effect for
sub-woofer, etc.)” channel, one of the six channels, is
an auxiliary channel, this format is called “5.1-channel
system.”
Not all Dolby Digital discs contain six (5.1) channel
information.
• DTS (Digital Theater Systems)
A surround audio format configured with six (5.1)
channels, which is the same as Dolby Digital. Because
the compression ratio is lower than Dolby Digital, it
provides wider dynamic range and better separation.
Not all DTS discs contain six (5.1) channel
information.
• MLP (Meridian Lossless Packing)
A format for DVD AUDIO with the compression ratio
of about 2:1 while allowing the PCM signal to be
completely recreated by the MLP decoder (required in
all DVD AUDIO players). It supports up to 192kHz/24bit.
The associated indicator lights up in the display window
when playing back a disc.
Indicator*
Audio format
LPCM
Linear PCM
DOLBY DIGITAL
Dolby Digital
DTS
DTS (Digital Theater Systems)
* When playing back a DVD AUDIO disc recorded by
MLP (Meridian Lossless Packing; a lossless audio
compression system that can completely recreate the
PCM signal), no indicator lights up in the display
window.
Note that, with some formats and/or depending on the
unit’s “DIGITAL AUDIO OUTPUT” setting, digital audio
signals are not always output from the unit’s DIGITAL
OUT jacks as are recorded on the disc.
See “DIGITAL AUDIO OUTPUT” on page 60 for details.
4
Downloaded From DvDPlayer-Manual.com JVC Manuals
Introduction
English
Disc structure
Press
RETURN.
Press
RETURN.
Press
RETURN.
(For DVD AUDIO)
Moving
picture
Menu
screen
1 2 3
4
Moving
picture
Still
picture
2
1 2
4
Group 2
Introduction
Still
picture
4
Group 1
Moving
picture
1
4
A DVD AUDIO disc is comprised of “groups,” and each
group is comprised of “tracks.” Some DVD AUDIO discs
also contain a “bonus group” that can be played back by
entering the “key number” (a kind of password). Usually
the contents of a “bonus group” are not opened to the
public. Note that most DVD AUDIO discs include other
information in addition to audio, such as still pictures,
movies and text.
Still
picture
Track 1 Track 2 Track 3 Track 4
Track 1 Track 2 Track 3
Care and handling of discs
(For DVD VIDEO)
How to handle discs
A DVD VIDEO disc is comprised of “titles” and each title
may be divided into some “chapters.” For example, if a
DVD VIDEO disc contains some movies, each movie may
have its own title number, and each movie may be
divided into some chapters. In a DVD VIDEO KARAOKE
disc, each song usually has its own title number and
does not have chapters.
Title 1
Title 2
When handling a disc, do not touch the surface of the
disc. Since discs are made of plastic, they are easily
damaged. If a disc gets dirty, dusty, scratched or warped,
the images and sound will not be picked up correctly,
and such a disc may cause the player to malfunction.
Chapter 1 Chapter 2 Chapter 3
Chapter 1 Chapter 2
(For SVCD/Video CD/Audio CD)
An SVCD, Video CD or Audio CD is simply comprised of
“tracks.”
Track 1
Track 2
Track 3
Track 4
Label side
Do not damage the label side, stick paper to or use any
adhesive on its surface.
Storage
Video CDs and SVCDs with Playback
Control function
What is Playback Control (PBC) function?
The Playback Control function, allows you to enjoy
menu-driven operation and high-resolution still images
which have a resolution four times greater than moving
pictures.
• High-resolution still image display
You can display high-quality images four times
clearer than moving pictures.
• Menu-driven playback
A selection menu is displayed when you start
playing an SVCD and Video CD disc with the
Playback Control feature. The selection menu
shows a list of numbers for selection. Some discs
may show moving pictures or a divided screen.
You can interact with the screen using a menu
display to select and play an entry.
See example illustration below about basic feature
of menu-driven playback (for details about PBC, see
also page 26).
Downloaded From DvDPlayer-Manual.com JVC Manuals
Make sure that discs are kept in their cases. If discs are
piled on top of one another without their protective
cases, they can be damaged. Do not put discs in a
location where they may be exposed to direct sunlight,
or in a place where the humidity or temperature is high.
Avoid leaving discs in your car!
Maintenance of discs
If there are fingerprints or other dirt adhering to a disc,
wipe with a soft dry cloth, moving from the center
outwards.
If a disc is difficult to clean, wipe with a cloth moistened
with water. Never use record cleaners, petrol, alcohol or
any anti-static agents.
CAUTION
Sometimes during play images may be garbled or
noisy. This is sometimes due to the disc.
5
Getting started
Connections
*Before using the unit, you have to connect the unit to a TV and/or amplifier.
Before making any connections
• Do not connect the AC power cord until all other connections have been made.
• Connect VIDEO OUT of the unit directly to the video input of your TV. Connecting VIDEO OUT of the unit to a TV via a
VCR may cause a monitor problem when playing back a copy-protected disc. You may also have a monitor problem
when connecting the unit to an integrated TV/Video system.
TV
VCR
Getting started
The unit
Connect directly
NOTES
• In the following description, “TV” may be substituted with “monitor” or “projector.”
• Terminal names used for other components may be different from those used in the following description.
To connect to a TV
Connection to a conventional TV
You can enjoy playback by simply connecting the unit to a TV.
Connect the unit to a TV equipped with stereo audio input and video input jacks using the supplied audio/video cables.
The unit
SUBWOOFER
CENTER RIGHT
REAR
RIGHT LEFT
PCM / STREAM
In this connection, set the
scanning mode selector to
“480i.”
LEFT
AV COMPU LINK
COMPONENT
VIDEO
Y
PB
480p
REMOTE
PR 480i
S-VIDEO
OPTICAL COAXIAL
DIGITAL OUT
AUDIO OUT
Red
TV
VIDEO OUT
Yellow
Scanning mode selector
Audio/video cable (supplied)
White
IN
Yellow
VIDEO
LEFT
White
AUDIO
RIGHT
Red
Connection to a TV equipped with an S-video jack
If your TV has an S-video input, you can get better picture quality by connecting it with the S-VIDEO output of the unit
using the S-video cable instead of connecting the video input of the TV to the VIDEO jack of the unit.
The unit
SUBWOOFER
CENTER RIGHT
PCM / STREAM
LEFT
REAR
RIGHT LEFT
In this connection, set the
scanning mode selector to
“480i.”
AV COMPU LINK
COMPONENT
VIDEO
Y
PB
480p
REMOTE
PR 480i
S-VIDEO
OPTICAL COAXIAL
DIGITAL OUT
AUDIO OUT
VIDEO OUT
Scanning mode selector
TV
IN
S-VIDEO
Red White
S-video cable (not supplied)
White
VIDEO
LEFT
AUDIO
Audio cable (supplied)
6
Downloaded From DvDPlayer-Manual.com JVC Manuals
RIGHT
Red
Getting started
Connection to a TV equipped with component jacks
English
You can enjoy high picture quality by connecting the unit’s COMPONENT VIDEO OUT jacks to the COMPONENT VIDEO IN
jacks of your TV with the video cables.
Blue
Component video cable (supplied)
Green
The unit
SUBWOOFER
CENTER RIGHT
PCM / STREAM
Red
LEFT
REAR
RIGHT LEFT
AV COMPU LINK
COMPONENT
VIDEO
Y
PB
Blue
480p
REMOTE
PR 480i
S-VIDEO
Green
OPTICAL COAXIAL
DIGITAL OUT
Red
AUDIO OUT
White
Red
TV
VIDEO OUT
IN
Scanning mode selector
Audio cable (supplied)
S-VIDEO
White
VIDEO
Y
PB
PR
COMPONENT IN
LEFT
Getting started
AUDIO
RIGHT
Red
• Connect “Y” to “Y,” “PB” to “PB”(CB), “PR” to “PR”(CR) correctly.
The unit supports the Progressive scanning system (480p) as well as the conventional Interlaced scanning system (480i).
If your television or monitor equipped with component jacks support the progressive video input, you can enjoy a high
quality picture by making the Progressive scanning mode active.
• If your television equipped with component jacks does not support the progressive scanning mode
Set the scanning mode selector to “480i.”
• If your television equipped with component jacks supports the progressive scanning mode
Set the scanning mode selector to “480p.”
• If you want to select the scanning mode between the interlaced and progressive modes
(depending on the source condition, or when connecting more than one television etc.)
You can select the mode from the remote control unit. To do this, set the scanning mode selector to “REMOTE.”
(See “To make the Progressive scanning mode selection active from the remote control unit” on page 8 for details
about how to select the scanning mode from the remote control unit when the scanning mode selector is set to
“REMOTE.”)
NOTES
• When the scanning mode is set to the progressive mode, the PROGRESSIVE indicator on the front panel is lit. The color of the
indicator differs depending on the “PROGRESSIVE MODE” setting on the “PICTURE” preference display and the status of the
unit (see pages 8 and 59).
• When connecting to a TV using the VIDEO or S-VIDEO jack, make sure that the PROGRESSIVE indicator on the front panel is
not lit. If it is lit, the VIDEO and S-VIDEO outputs do not feed the correct signals. To turn off the PROGRESSIVE indicator, set the
scanning mode selector on the rear panel to “480i.” Or, while setting the scanning mode selector to “REMOTE,” make the
Progressive scanning mode inactive by following the procedure described on page 8.
• When the component video input jacks on the TV is of the BNC type, use an adapter to convert a pin jack to a BNC jack
(optional).
• Set “ANALOG OUT” in the “AUDIO” preference display to “2-CH STEREO” (see page 61).
• If your TV has a monaural audio input instead of stereo, you need to use an optional audio cable which converts stereo audio
output to monaural.
• To improve audio sound quality, connect the AUDIO OUT jacks to your separate audio equipment (see the following pages).
• If your TV has an AV COMPU LINK terminal, you can use the AV COMPU LINK function. See “AV COMPU LINK remote control
system” on page 71 for details.
Downloaded From DvDPlayer-Manual.com JVC Manuals
7
Getting started
About SCANNING MODE
To display video on the television (monitor) screen, the conventional scanning method is called “Interlaced scanning.”
With this method, only half of the horizontal lines are displayed at a time. So two fields complete a single picture
(frame); i.e., the first field, containing all the odd-numbered lines, is displayed followed by the second field, containing
all the even-numbered lines.
On the other hand, the Progressive scanning system scans all horizontal lines at a time, so you can double the number
of pictures compared with the interlaced scanning, resulting in flicker-free, high-density picture.
Getting started
Depending on the material source format, DVD VIDEO discs can be classified into two types; film source and video
source (note that some DVD VIDEO discs contain both film source and video source). Film sources are recorded as 24frame-per-second information, while (NTSC) video sources are recorded as 30-frame-per-second (60-field-per-second
interlaced) information.
When the unit plays back a film source material, uninterlaced progressive output signals are created using the original
information. When a video source material is played back, the unit interleaves lines between the interlaced lines on
each to create the interpolated picture and outputs as the progressive signal.
To make the Progressive scanning mode selection active from the remote control unit
The unit supports the Progressive scanning system as well as the conventional Interlaced scanning system. If your television
or monitor supports the progressive video input, you can enjoy a high quality picture by making the Progressive scanning
mode active.
If you want to select the scanning mode between the interlace and progressive modes depending on the
480p
source condition or when connecting more than one television, you can select the mode from the remote
REMOTE
480i
control unit. To do this, set the scanning mode selector on the rear panel to “REMOTE.”
¶ When the unit is turned on, and the scanning mode selector on the rear panel is set to “REMOTE.”
Press and hold down VFP - PROGRESSIVE SCAN for a few seconds.
The scanning mode switches between the Progressive scanning and Interlaced scanning modes.
• When the scanning mode is set to the progressive mode, the PROGRESSIVE indicator on the front panel is lit.
Depending on the “PROGRESSIVE MODE” setting on the “PICTURE” preference display and whether the current
DVD VIDEO disc is film-source or video-source, the color of the indicator differs, as shown in the table below
(see also pages 7 and 59).
Source type of DVD VIDEO
Setting of
PROGRESSIVE MODE
Film Source
Video Source
VIDEO
Red
Red
FILM
Green
Green
AUTO
Green
Red
TV
While stopped in the Progressive scanning
mode, the PROGRESSIVE indicator is lit in red
regardless of the “PROGRESSIVE MODE”
selection.
DVD
STANDBY/ON
OPEN/
CLOSE
TV
TV1
DVD
TV2
TV3
1
2
3
TV4
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
PAGE
RETURN
T
Note
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
N
STROBE
DVD AUDIO/DVD VIDEO/SUPER VCD/VCD/CD PLAYER
0 OPEN/CLOSE
7 STOP
3 PLAY
8 PAUSE
4
SKIP
¢
STANDBY/ON
SLOW+
SLOW-
STANDBY/ON
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
3D
PHONIC
ANGLE
ZOOM
AMP VOL
VFP PROGRESSIVE
SCAN
PROGRESSIVE DVD AUDIO
PROGRESSIVE indicator
RM-SXV011J
REMOTE CONTROL
NOTES
• There are some progressive TV and High-Definition TV sets that are not fully compatible with the unit, resulting in the
unnatural picture when playing back a DVD VIDEO disc in the Progressive scanning mode. In such a case, use the Interlaced
scanning mode. To check the compatibility of your TV set, contact your local JVC customer service center.
• All JVC progressive TV and High-Definition TV sets are fully compatible with the unit (Example : AV-61S902).
8
Downloaded From DvDPlayer-Manual.com JVC Manuals
Getting started
English
To connect to a stereo audio amplifier/receiver
You can enjoy high-quality audio by connecting the unit’s audio output to your amplifier or receiver.
Connect the unit’s AUDIO OUT (LEFT/RIGHT) jacks to any line-level inputs (such as AUX, DVD, CD, etc.) of an audio
amplifier or receiver.
The unit
CENTER RIGHT
SUBWOOFER
PCM / STREAM
LEFT
REAR
RIGHT LEFT
AV COMPU LINK
COMPONENT
VIDEO
Y
PB
480p
REMOTE
PR 480i
S-VIDEO
OPTICAL COAXIAL
DIGITAL OUT
AUDIO OUT
Red
VIDEO OUT
Amplifier or receiver
White
White
Audio cable (supplied)
IN
LEFT
AUDIO
Getting started
RIGHT
Red
NOTES
• When using the unit with a stereo amplifier or receiver, set “ANALOG OUT” in the “AUDIO” preference display to “2-CH
STEREO” (see page 61).
• If your stereo amplifier or receiver has an AV COMPU LINK terminal, you can use the AV COMPU LINK function. See “AV
COMPU LINK remote control system” on page 71 for details
To connect to an amplifier/receiver equipped with 5.1-channel inputs
The unit supports the linear PCM multichannel format of DVD AUDIO and can feed multichannel audio output signals
from the six analog AUDIO OUT jacks.
It is also equipped with the DTS and Dolby digital decoders. So you can enjoy any type of the high quality surround
sounds by connecting the unit to an amplifier/receiver equipped with the 5.1-channel inputs.
Connect the unit’s analog AUDIO OUT jacks to the analog 5.1-channel inputs of an amplifier or receiver using the
supplied audio cables.
The unit
CENTER RIGHT
SUBWOOFER
LEFT
AV COMPU LINK
REAR
RIGHT LEFT
PCM / STREAM
COMPONENT
VIDEO
Y
PB
PR
480p
REMOTE
480i
S-VIDEO
OPTICAL COAXIAL
DIGITAL OUT
AUDIO OUT
VIDEO OUT
White
Red
White
Red
Yellow
White
Red
Amplifier or receiver
Audio/video
cable
(supplied)
White
AUDIO IN
FRONT
LEFT
Yellow
RIGHT
Red
White
REAR
LEFT
RIGHT
Audio cable
(supplied)
Red
CENTER
White
SUBWOOFER
Audio cable
(supplied)
Red
• Be sure to connect correctly between corresponding terminals. The order of the 5.1-channel terminals depend on units.
NOTES
• When using the 5.1-channel outputs of the unit, set the “ANALOG OUT” in the “AUDIO” preference display to “MULTI
CHANNEL” (see page 61). If you select “EXPERT” in the “SPK.SETTING” preference display, you can control the audio output
balance of the speakers (see page 62).
Downloaded From DvDPlayer-Manual.com JVC Manuals
9
Getting started
To connect to a digital audio device
You can enhance the sound quality by connecting either of the unit’s DIGITAL OUT jacks to the digital input of an
amplifier, etc. by using an optical or a coaxial digital cable (optional). The digital audio signal from a disc is directly
transferred. If you connect the unit to a Dolby Digital or DTS decoder or an amplifier with a built-in decoder by using an
optional digital cable, you can enjoy high-quality surround sound.
For digital connection, connect the unit’s DIGITAL OUT (OPTICAL or COAXIAL) to the digital input of digital audio device
using an optical or a coaxial digital cable.
When using the DIGITAL OUT (OPTICAL) jack, remove the protection
cap. Do not lose the removed cap.
When the DIGITAL OUT (OPTICAL) jack is not used, fix the protection
cap into the jack.
The unit
Getting started
SUBWOOFER
CENTER RIGHT
PCM / STREAM
LEFT
REAR
RIGHT LEFT
AV COMPU LINK
COMPONENT
VIDEO
Y
PB
480p
REMOTE
PR 480i
S-VIDEO
OPTICAL COAXIAL
DIGITAL OUT
Red
AUDIO OUT
VIDEO OUT
White
Coaxial digital cable (not supplied)
Optical digital cable (not supplied)
Digital equipment
Audio cable (supplied)
White
IN
IN
LEFT
OPTICAL
AUDIO
RIGHT
DIGITAL
COAXIAL
Red
Note that the DIGITAL OUT jacks on the unit have been designed and equipped exclusively for enjoying the digital
surround sound playback through the unit. It is not recommended to use the jacks for digital dubbing. When recording
the sounds (DVD AUDIO, DVD VIDEO, SVCD, Video CD, or Audio CD) played back on the unit, record them through the
analog jacks (in this case, set “ANALOG OUT” in the “AUDIO” preference display to “2-CH STEREO”) (see page 61).
NOTES
• When you connect the unit’s DIGITAL OUT to a digital audio device, before using, set “DIGITAL AUDIO OUTPUT” in the
“AUDIO” preference display correctly according to the connected audio device. If “DIGITAL AUDIO OUTPUT” is not set correctly,
loud noise may be generated from speakers, causing damage to them. See “DIGITAL AUDIO OUTPUT” on page 60.
• When you connect the unit’s DIGITAL OUT to a Dolby Digital or DTS decoder (or amplifier with a built-in decoder) to enjoy
surround sound, the unit’s “D. RANGE COMPRESSION” setting in the “AUDIO” preference display is invalid. Make appropriate
surround audio settings on the decoder.
• If your digital audio device has an AV COMPU LINK terminal, you can use the AV COMPU LINK function. See “AV COMPU LINK
remote control system” on page 71 for details.
10
Downloaded From DvDPlayer-Manual.com JVC Manuals
Getting started
To connect the power cord
English
When all the audio/video connections have been made, insert the smaller plug of the supplied AC power cord to the
unit’s
AC IN connector, then insert the other end to the wall outlet. Make sure that plugs are inserted firmly. The
STANDBY/ON indicator lights in red.
NOTE (only for PX model)
• Use the supplied AC power plug adaptor when inserting the larger plug to the wall outlet.
•
•
•
•
•
Disconnect the power cord if you are not going to use the unit for a long time.
Disconnect the power cord before cleaning the unit.
Disconnect the power cord before moving the unit.
Do not connect or disconnect the power cord with wet hands.
Do not pull the power cord when disconnecting it, as this may damage the cord and cause fire, electric shock, or other
accidents.
Caution
• Do not alter, twist or pull the power cord, or put anything heavy on it, which may cause fire, electric shock, or other
accidents.
• To prevent any accidents or damage caused by an unsuitable AC power cord, only use the supplied power cord. If the
cord is damaged, contact a dealer and get another power cord.
Downloaded From DvDPlayer-Manual.com JVC Manuals
Getting started
Warning
11
Getting started
Using the remote control unit
Using the remote control unit, you can operate not only all the functions of the unit but also basic functions of your TV
and amplifier/receiver.
To install batteries in the remote
control unit
The battery compartment is located on the back of the
remote control unit.
Getting started
1 Press down on the point shown by
the arrow at the top of the
compartment cover, and pull up
the cover to open the
compartment.
Remote sensor
• Operate the remote control unit while pointing it
toward the remote sensor on the unit.
• The remote control unit can be used within a range of
about 5 meters from the remote sensor. If you operate
the remote control unit from a diagonal position,
controllable distance may be shorter.
Remote sensor
2 Place the two supplied R6P (SUM-
DVD AUDIO/DVD VIDEO/SUPER VCD/VCD/CD PLAYER
0 OPEN/CLOSE
7 STOP
3 PLAY
8 PAUSE
4
SKIP
¢
STANDBY/ON
STANDBY/ON
3)/AA(15F) batteries in the remote
control unit according to the
polarity markings (“+” and “–”)
inside the compartment and on the
batteries.
PROGRESSIVE DVD AUDIO
3 Place the cover over the
compartment, and press down
lightly.
TV
TV
TV1
T
DVD
TV2
TV3
1
2
3
TV4
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
+10
PAGE
RETURN
The batteries will last about six months with normal use.
If the functions of the remote control unit become erratic,
replace the batteries. See below for more information.
DVD
STANDBY/ON
OPEN/
CLOSE
OP
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
ME
NU
VOL-
VOL+
ENTER
CH
OIC
E
EN
RE
SC
ON
NEXT
CH
-
PREVIOUS
CLEAR
SELECT
STROBE
SLOW-
Precautions for the safe use of batteries
SLOW+
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
Observe the following precautions for the safe use of
batteries. If they are used improperly their life will be
shortened, they may burst or their contents may leak.
3D
PHONIC
ANGLE
ZOOM
AMP VOL
RM-SXV011J
REMOTE CONTROL
Precaution
• Remove the batteries from the remote control unit if
it is not going to be used for a long period of time.
• Remove dead batteries and dispose of them
properly.
• Never leave dead batteries lying around, take them
apart, mix them with other refuse, or throw them
into an incinerator.
• Never touch liquid that has leaked out of a battery.
• Do not mix new and old batteries, or batteries of
different types, when replacing them.
12
Downloaded From DvDPlayer-Manual.com JVC Manuals
NOTE
• If the remote sensor on the unit is exposed to the
sunshine or strong light, you may not be able to control
the unit from the remote control unit.
Getting started
To use the remote control unit for TV
operation
You can operate your TV from the remote control unit.
Setting the remote control signal for
operating your TV
TV
TV
TV1
1
2
3
TV5
TV6
4
5
6
TV7
TV8
TV9
8
9
TV0
MUTING
0
OP
TV/VIDEO
CANCEL
ME
NU
VOL+
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
TV STANDBY/ON
.
If your TV turns on or off, you have successfully set
the control signal.
The following buttons can be used for operating the
TV.
To use 5/∞ (CH+, CH−), 2/3(VOL−, VOL+), TV/VIDEO CANCEL and numeric buttons for TV control, set the
TV - DVD switch to “TV.”
TV
SELECT
TV/VIDEO CANCEL
Turns the TV on or off.
TV
N
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
VFP
TV/VIDEO
CANCEL
fs/Rate PROGRESSIVE
SCAN
DIGEST
DVD
+10
TITLE/
GROUP
NU CH
ME
+
VOL-
ENTER
Numeric buttons
7
TV-/--
PAGE
6 Try to operate the TV by pressing
TV3
TV4
10
TV - DVD switch
DVD
TV2
RETURN
T
DVD
STANDBY/ON
OPEN/
CLOSE
ANGLE
3D
PHONIC
English
ZOOM
Switches the TV input mode between TV
and VIDEO.
Getting started
TV STANDBY/ON
5 Release TV/VIDEO - CANCEL.
AMP VOL
1 Set the TV - DVD switch to “TV.”
2 Hold down TV/VIDEO - CANCEL until step 4 is
finished.
TV1
1
~
TV-/--
10
TV0
0
3 Enter the manufacturer code of your TV listed below
Selects the TV channels directly.
* For some TVs, pressing “+10” functions
as the “100+,” while “10” functions as
the ENTER button if your TV requires
pressing the ENTER button after
selecting a channel number.
by using the numeric buttons (0 to 9).
Mutes the TV sound.
MUTING
Example:
To enter the manufacturer code “01”: Press “0” then
“1.”
• When the unit is shipped, the manufacturer code is set to
“JVC” (01).
+10
Changes the TV channels.
CH
+
CH
-
VOL-
4 Press ENTER.
VOL+
Adjusts the TV volume.
Manufacturer code list
Manufacturer
No.
Manufacturer
No.
AIWA
36
MIVAR
29
BEIJING
22
NEC
20
CCE
02
NOBLEX
22
CHANGHONG
34
NOKIA
31
DAEWOO
17, 37
PANASONIC
04, 11
FERGUSON
27
PEONY
34, 38, 39
10, 17, 21
FINLUX
30
PHILCO
FUNAI
32
PHILIPS
02
GRADIENTE
15, 20
RCA
05
GRUNDIG
19
SAMSUNG
HITACHI
10
12, 33, 34,
35
ITT
28
SANYO
13, 16
JINXING
38
SEARS
13
JVC
01, 23,
24, 25
SHARP
06
SONY
07
KONKA
40
TCL
41
LG (GOLDSTAR)
18
THOMSON
26
MAGNAVOX
02
TOSHIBA
08,14
MITSUBISHI
03
ZENITH
09
Downloaded From DvDPlayer-Manual.com JVC Manuals
NOTE
• If there is more than one code listed for the
manufacturer of your TV, try them one by one until you
succeed.
To control the volume of a JVC’s
amplifier or receiver
You can control the volume of a JVC’s amplifier or
receiver by using the AMP VOL +/− buttons on the
remote control unit.
AMP VOL
Pressing the + button raises the audio volume of the
amplifier or receiver, while pressing the – button lowers
the volume.
13
Basic operations
In the following description, we assume that the buttons on the remote control unit are mainly used, however, you may
use the corresponding buttons on the front panel if available.
NOTE
TV
Make sure that the TV - DVD switch on the remote control unit is set to “DVD” when using the 5/∞/
2/3 and numeric buttons for controlling the unit.
DVD
Before operation
Turning on/off the unit
Press DVD STANDBY/ON
on the remote control unit or press STANDBY/ON
on the front panel.
When the unit turns on, the STANDBY/ON indicator on the front panel, which illuminates in red during standby, lights in
green.
TV
TV
TV1
Basic operations
DVD
TV2
2
3
TV5
TV6
4
5
TV7
TV8
DVD
STANDBY/ON
TV3
1
TV4
6
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
PAGE
RETURN
T
DVD
STANDBY/ON
OPEN/
CLOSE
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
DVD AUDIO/DVD VIDEO/SUPER VCD/VCD/CD PLAYER
STANDBY/ON
0 OPEN
STANDBY/ON
STANDBY/ON
VOL-
VOL+
ENTER
CH
OIC
E
PROGR
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
N
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
STANDBY/ON indicator
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
3D
PHONIC
ANGLE
ZOOM
AMP VOL
RM-SXV011J
REMOTE CONTROL
• You can turn on the unit by pressing the 3 button. In this case, the unit starts playback if the disc is set in the disc tray.
If no disc is set, “NO DISC” appears on the display window.
• You can turn on the unit by pressing the 0 OPEN/CLOSE button on the front panel. In this case, the disc tray opens.
The opening display shown right appears on the TV screen.
The following message may appear at the bottom of the opening display
depending on the condition.
• NOW READING:The unit is reading the disc information.
• REGION CODE ERROR!:
The region code of the DVD VIDEO disc does not
match the unit. The disc cannot be played back.
• OPEN:
The disc tray is opening.
• CLOSE:
The disc tray is closing.
• NO DISC:
No disc is loaded.
• RESUME STOP: The resume mode is set to “DISC RESUME.”
NOW READING
Message area
When turning on the unit for the first time, the DVD PLAYER SET UP display automatically appears (see page 15).
NOTE
• Even if you press DVD STANDBY/ON
on the remote control unit or STANDBY/ON
on the front panel to turn off the unit,
the unit is not disconnected from the AC power source as long as it is connected to the wall outlet. This state is called the
standby mode. In this state, the unit consumes a very small amount of power.
14
Downloaded From DvDPlayer-Manual.com JVC Manuals
Basic operations
English
The initial setup before using the unit
We recommend you to set the display language, TV monitor type, analog audio output and digital output before using
the unit, depending on circumstances, by following the procedure below.
When turning on the unit for the first time, the DVD PLAYER SET UP display automatically appears. In such a case,
perform the following procedure from step 2.
See “Changing the initial settings” on and after page 56 for details about each setting item.
TV
TV
TV1
ENTER
DVD
TV2
TV3
1
2
3
TV4
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
+10
PAGE
RETURN
T
DVD
STANDBY/ON
OPEN/
CLOSE
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
CHOICE
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
5/∞
N
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
3D
PHONIC
ANGLE
ZOOM
AMP VOL
Basic operations
DIGEST
RM-SXV011J
REMOTE CONTROL
1 Press and hold down CHOICE for a few
seconds to bring up the first page of the DVD
PLAYER SET UP display.
The pull-down menu of the “ON SCREEN
LANGUAGE” is already open.
4 Use 5/∞ to select a desired monitor type.
You can select the monitor type according to your TV.
• For the normal (conventional) TV, select “4:3 LB”
or “4:3 PS.”
• For the wide-screen TV, select “16:9 AUTO” or
“16:9 NORMAL.”
See page 59 for details about each mode.
DVD PLAYER SET UP
MENU LANGUAGE
ENGLISH
AUDIO LANGUAGE
ENGLISH
SUBTITLE
ENGLISH
ON SCREEN LANGUAGE
ENGLISH
ENGLISH
SPANISH
FRENCH
SELECT
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
ENTER
5 Press ENTER.
The third (final) page is shown, in which the pulldown menu of the “ANALOG OUT” is already
open.
ON SCREEN LANGUAGE selection
DVD PLAYER SET UP
DIGITAL AUDIO OUTPUT
2 Use 5/∞ to select a desired language.
ANALOG OUT
SELECT
ENTER
3 Press ENTER.
DVD PLAYER SET UP
MONITOR TYPE
4:3 L.B.
16:9 NORMAL
PROGRESSIVE MODE
AUTO AUTO
16:9
SCREEN SAVER
4:3
ON LB
SELECT
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
ANALOG OUT selection
The second page is shown, in which the pull-down
menu of the “MONITOR TYPE” is already open.
ENTER
DOLBY PROLOGIC
ON
2-CH
STEREO
MULTI CHANNEL
You can select the on-screen language for the
preference displays, etc. from among English,
Spanish and French.
MP3/JPEG
STREAM/PCM
2-CH DOLBY SURROUND
D. RANGE COMPRESSION
4:3 PS
MP3
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
MONITOR TYPE selection
Downloaded From DvDPlayer-Manual.com JVC Manuals
6 Use 5/∞
to select a desired analog output
signal type.
You must set this item correctly when you play back
a DVD VIDEO disc recorded with surround
multichannel audio.
• When connecting with a surround decoder, select
“2-CH DOLBY SURROUND.”
• When connecting with a stereo amplifier/receiver
or television set, select “2-CH STEREO.”
• When connecting the unit’s 5.1 channel audio
outputs to an amplifier equipped with 5.1-channel
input, select “MULTI CHANNEL.”
See page 61 for details.
15
Basic operations
7 Press ENTER.
The pull-down menu of the “DIGITAL AUDIO
OUTPUT” appears.
DVD PLAYER SET UP
DIGITAL AUDIO OUTPUT
DOLBY DIGITAL/PCM
PCM ONLY
ANALOG OUT
DOLBY PROLOGIC
DOLBY
DIGITAL/PCM
D. RANGE COMPRESSION
STREAM/PCM
ON
SELECT
ENTER
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
DIGITAL AUDIO OUTPUT selection
8 Use 5/∞ to select a desired digital output
Basic operations
signal type.
You must set this item correctly when you connect
the unit to an external surround decoder or D/A
convertor (including an amplifier/receiver with
built-in surround decoder or D/A convertor).
(If you do not connect the unit to such a device, you
do not have to set this item.)
• When connecting with a Dolby Digital decoder,
select “DOLBY DIGITAL/PCM.”
• When connecting with a DTS or MPEG
Multichannel decoder, select “STREAM/PCM.”
• When connecting with other digital devices,
select “PCM ONLY.”
See page 60 for details.
9 Press ENTER.
The TV screen returns to show the opening display.
NOTES
• This setting may not be necessary except when turning
on the power after purchasing the unit.
• You can also set these items, as well as other
preferences, by pressing CHOICE briefly to bring up the
preference display. See “Changing the initial settings”
on and after page 56 for details.
16 From DvDPlayer-Manual.com JVC Manuals
Downloaded
Basic operations
English
Basic playback
This section describes basic operations for playback of DVD AUDIO, DVD VIDEO, SVCD, Video CD and Audio CD discs.
For MP3 and JPEG disc playback, see the separate chapter on and after pages 47 and 51.
TV
OPEN/CLOSE
TV
TV1
DVD
TV2
TV3
1
2
3
TV4
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
PAGE
RETURN
T
DVD
STANDBY/ON
OPEN/
CLOSE
7 3 8
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
DVD AUDIO/DVD VIDEO/SUPER VCD/VCD/CD PLAYER
7 STOP
0 OPEN/CLOSE
VOL+
3 PLAY
4
8 PAUSE
SKIP
¢
STANDBY/ON
ENTER
CH
OIC
E
STANDBY/ON
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
7
CLEAR
SELECT
N
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
PROGRESSIVE DVD AUDIO
3
8
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
3D
PHONIC
ANGLE
ZOOM
DVD AUDIO indicator
Disc tray
0OPEN/CLOSE
AMP VOL
RM-SXV011J
Basic operations
REMOTE CONTROL
Inserting and removing discs
1 Press 0 OPEN/CLOSE to open the disc tray.
2 Place a disc in the tray.
3 Press 0 OPEN/CLOSE to close the disc tray.
With the label side up
The unit reads the disc information and the
opening display appears on the TV screen.
4
P¢
SKI
SE
8 PAU
Y
P
3 PLA
7 STO
/CD
CD
D/V
R VC
PE
/SU
EO
D VID
/DV
DIO
D AU
DV
When a DVD AUDIO disc is loaded, the DVD AUDIO
indicator lights in blue.
STAN
DBY/
ER
PLAY
E
LOS
N/C
0 OPE
PRO
E
SSIV
GRE
DVD
IO
AUD
ON
N
Y/O
NDB
STA
If a menu is shown on the TV screen
• To insert an 8-cm disc,
place it in the inner
recess.
When inserting a DVD AUDIO, DVD VIDEO, SVCD, or
Video CD disc, a menu display may be automatically
shown on the TV screen. From a menu, you can select
a desired item to be played back by following the
procedure below.
(for DVD AUDIO/DVD VIDEO)
1 Use 5/∞/2/3 to select a desired item.
2 Press ENTER.
The unit starts playback of the selected item.
(for SVCD/Video CD)
Use the numeric buttons to select a desired item.
The unit starts playback of the selected item.
NOTES
• Do not load a non-playable disc. For details about playable and non-playable disc types, see page 4.
• When loading a disc on the tray, be sure to position the disc inside the recess. Otherwise, the disc may be damaged when the
tray is closed, or the disc may not be removed from the unit.
• Do not use any stabilizer when playing back a disc.
• With some DVD VIDEO discs, the unit starts playback automatically after inserting the disc.
• If you insert a DVD VIDEO disc whose region code does not match the unit, “REGION CODE ERROR!” is shown in the opening
display. For detail about the region code, see page 4.
Downloaded From DvDPlayer-Manual.com JVC Manuals
17
Basic operations
To start playback
Available :
Press 3.
The unit starts playback from the beginning.
About screen saver function
• A television monitor screen may be burned out if a static
picture is displayed for a long time. To prevent this, the unit
automatically activates the screen saver function if a static
picture, such as an on-screen display or menu, is displayed
for over 5 minutes.
While the screen saver
function is not activated
While the screen saver
function is activated
• Pressing any buttons on the unit or the remote control unit
will release the screen saver function and return to the
previous display.
• You can also turn off the screen saver function (see page 60).
Basic operations
About On-screen guide icons
• When you make an operation, you may see the following icons displayed over the picture for about 3 seconds. These have the
following meanings.
You can set the unit not to display these icons below via the preference settings described on page 63.
Icon
Status
Appears at the beginning of playback mode.
Appears at the beginning of pause mode.
Appears at the beginning of fast forward/backward playback with the current speed (see page 21).
Appears at the beginning of slow-motion playback with the current speed (see page 21).
Appears at the beginning of Repeat playback mode (see page 33).
Appears at the beginning of a scene recorded from multiple angles (see page 37).
Appears at the beginning of a scene recorded with multiple audio languages (see page 36).
Appears at the beginning of a scene recorded with multiple subtitle languages (see page 35).
Appears when the unit does not accept your operation because of disc contents, structure, playback status etc.
Note that some operations are occasionally unacceptable even if
when ON SCREEN GUIDE in the preference display is set to OFF.)
is not displayed. (This icon appears even
NOTES
• When the RESUME function is “ON” or “DISC RESUME” and the resume point is memorized, pressing 3 starts playback from
that point instead of the beginning. See page 20.
• During playback, the display window shows the title/chapter, group/track, or track number being played.
• During DVD VIDEO playback, pressing 3 moves back the playback position 10 seconds before the current position. See page 25
for details.
To stop playback completely
Available :
Press 7.
The unit stops playback.
• If you press 0 OPEN/CLOSE during playback, the unit stops playback and opens the disc tray.
To stop playback temporarily
Available :
Press 8.
The unit pauses playback. To resume playback, press 3.
18 From DvDPlayer-Manual.com JVC Manuals
Downloaded
Basic operations
English
Resuming playback
The unit can memorizes the position on a disc where you interrupt playback, and resume playback from that position later.
There are two resume modes (DISC RESUME and ON) you can set on the preference display. See page 63 for details
about how to set the resume mode.
• When purchasing the unit, the resume mode is initially set to “ON”.
• You can deactivate the resume mode by setting “RESUME” on the “OTHERS” preference display to “OFF”.
TV
OPEN/CLOSE
DVD
STANDBY/ON
OPEN/
CLOSE
TV
TV1
TV2
DVD
2
3
TV5
TV6
4
5
6
TV7
TV8
7
8
TV-/--
TV0
10
0
RETURN
PAGE
7 3
TV3
1
TV4
TV9
DVD AUDIO/DVD VIDEO/SUPER VCD/VCD/CD PLAYER
9
0 OPEN/CLOSE
MUTING
7 STOP
3 PLAY
8 PAUSE
4
SKIP
¢
STANDBY/ON
+10
TITLE/
GROUP
STANDBY/ON
TV/VIDEO
CANCEL
T
PROGRESSIVE DVD AUDIO
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
7
CLEAR
SLOW-
SELECT
STROBE
N
3
Disc tray
0OPEN/CLOSE
SLOW+
Basic operations
.
To memorize the interrupted position
Available :
¶ During playback
When the resume mode is set to “DISC RESUME”
Press 7 .
The unit stops playback and memorizes the interrupted position. After pressing 7, the display window on the front
panel shows “----RESUME.”
In this condition, a memory of the interrupted position is not cleared if you press 0 OPEN/CLOSE to open the disc
tray, or press DVD STANDBY/ON
on the remote control unit or STANDBY/ON
on the front panel to turn off the
unit.
• The position interrupted is also memorized by pressing OPEN/CLOSE, DVD STANDBY/ON
on the remote control unit or
0 OPEN/CLOSE, STANDBY/ON
on the front panel. In this case, “----RESUME” is not shown on the display window.
• If you do not want the disc played to resume playback, press 7 while stopped.
• It memorizes positions for the last 30 discs.
• If you interrupt playback of a disc which you resumed playback, the memory is updated to store the new interrupted position.
• When the unit has already memorized positions for 30 discs, memorizing one more position for a disc automatically erases the
oldest memory. On the other hand, if you interrupt playback of a disc which an interrupted position is already memorized, the order
of memorized discs may change. In result, when memorizing a new data, the order of memorized discs to be erased also may
change.
When the resume mode is set to “ON”
Press 7 .
The unit stops playback and memorizes the interrupted position.
In this condition, a memory of the interrupted position is not cleared until you press OPEN/CLOSE,
DVD STANDBY/ON
on the remote control unit or 0 OPEN/CLOSE, STANDBY/ON
on the front panel.
• If you do not want the disc played to resume playback, press 7 while stopped.
Downloaded From DvDPlayer-Manual.com JVC Manuals
19
Basic operations
To resume playback
Available :
When the resume mode is set to “DISC RESUME”
¶ While stopped, or no disc is inserted
1 Press 0 OPEN/CLOSE to insert a disc whose interrupted position is
memorized.
After loading the disc, the display window on the front panel shows “---RESUME” and “RESUME STOP” appears at the bottom of the opening
display.
If a disc for which you want to resume playback is already set in the disc tray,
you need not to follow this step.
RESUME STOP
Basic operations
2 Press 3.
The display window shows “RESUME PLAY” and the unit resumes playback from the position you interrupted
playback.
The unit keeps the memory for the position on a disc where you interrupted playback, even though you remove the
disc from the disc tray and set it back again.
Of course, the unit keeps the memory when the disc remains in the disc tray since the last playback.
• To play back a disc from the beginning (instead of the interrupted position)
After loading the disc, press 7 before pressing 3 to start playback.
Pressing 7 while the disc is stopped clears the memory for the interrupted position.
Every time you interrupt playback, the position is memorized as the “resuming” point.
When the resume mode is set to “ON”
¶ While the disc you interrupted playback last time* is still on the disc tray (*by pressing 7).
Press 3.
The unit resumes playback from the position you interrupted playback.
If you press 3 then 7, the unit starts playback after the display window shows “RESUME PLAY.”
Note that you cannot resume playback if you interrupted playback last time by opening the tray or turning off the
power.
• To play back a disc from the beginning (instead of the interrupted position)
Carry out any of the followings:
* Press 7 while stopped, then press 3.
* Turn off and on the unit by pressing DVD STANDBY/ON
on the remote control unit or STANDBY/ON
front panel then press 3.
on the
NOTES
• If you change the “RESUME” setting on the “OTHERS” preference display to “OFF” or “ON” from “DISC RESUME,” you cannot
resume playback of a disc whose “resuming” position is memorized. However, if you again set “RESUME” to “DISC RESUME,”
you can resume playback of the disc.
• If you open the tray with the RESUME mode set to ON, the “resuming” point clears.
• The resume function cannot be performed with Audio CD, MP3 and JPEG discs.
• In the case of an SVCD/Video CD disc with PBC function, the unit may resume playback from a point slightly earlier or later
than the point you interrupt playback last time.
• The unit may not resume playback exactly from the interrupted point, depending on the point.
• For a double-sided DVD AUDIO/DVD VIDEO disc, the unit regards each side as a different disc. Therefore, when resuming
playback of such a disc, make sure to set the disc with the resumed side down.
• When the unit memorizes the interrupted point of a disc, it also memorizes Audio, Subtitle and Angle settings (regardless of
whether “RESUME” is set to “DISC RESUME” or “ON”).
• If you interrupt playback while the menu for a DVD AUDIO, DVD VIDEO, SVCD or Video CD is shown on the TV screen, the unit
may not memorize the interrupted position correctly, regardless of whether the “RESUME” mode is set to “ON” or “DISC
RESUME.”
20 From DvDPlayer-Manual.com JVC Manuals
Downloaded
Basic operations
English
Variable speed playback
You can play back slowly or fast, or advance a picture frame by frame.
T
RETURN
PAGE
GROUP
NU CH
ME
+
OP
CANCEL
ME
NU
VOL-
8
VOL+
ENTER
4/¢
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
N
DVD AUDIO/DVD VIDEO/SUPER VCD/VCD/CD PLAYER
0 OPEN/CLOSE
7 STOP
3 PLAY
8 PAUSE
4
SKIP
¢
STANDBY/ON
CLEAR
SELECT
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
ANGLE
3D
PHONIC
ZOOM
8
STANDBY/ON
PROGRESSIVE DVD AUDIO
1/¡
4/¢
AMP VOL
To advance or reverse playback rapidly while monitoring
Available :
¶ During playback
Press 1 or ¡.
Each press of 1 or ¡ increases the playback speed. You can select the speed among 2 x, 5 x, 10 x, 20 x and 60 x
the normal speed.
Pressing 3 returns the unit to normal playback.
Method 2
Hold down 4 or ¢.
Holding down ¢ advances playback rapidly, while holding down 4 reverses playback rapidly at five times the
normal speed. Releasing the button returns the unit to normal playback.
NOTES
• During this operation, the sound is muted except when a DVD AUDIO and an Audio CD are played back. When playing back
them in this function, the sound will come out discontinuously.
• This function does not work for an MP3 disc.
To advance a still picture frame-by-frame
Available :
¶ While paused (still)
Press 8.
Each time you press 8, the still picture advances to the next frame.
Pressing 3 returns to normal playback.
To play back in slow-motion
Available :
You can play back the picture in slow-motion. The speed can be selected among 1/32 x, 1/16 x, 1/8 x, 1/4 x and 1/2 x the
normal speed.
¶ During playback
Press 8, then use 1/¡.
To play forward slow-motion, press ¡, and to play reverse slow-motion (for DVD VIDEO discs only), press 1 .
First, the unit plays the slowest speed, and each time you press the button, the playback speed increases.
Pressing 3 returns to normal playback. Pressing 8 pauses slow-motion playback.
NOTES
• The sound is muted during slow-motion playback.
• Reverse slow-motion playback is not possible for an SVCD and Video CD.
Downloaded From DvDPlayer-Manual.com JVC Manuals
21
Basic operations
Method 1 (from the remote control unit only)
Basic operations
To locate the beginning of the scene or song
You can locate the desired group or track (for DVD AUDIO), title or chapter (for DVD VIDEO), or track (for SVCD/Video CD/
Audio CD) from which the unit starts playback.
TV
TV
TV1
Numeric
buttons
DVD
TV2
TV3
1
2
3
TV4
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
PAGE
RETURN
T
DVD
STANDBY/ON
OPEN/
CLOSE
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
4/¢
VOL+
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
N
DVD AUDIO/DVD VIDEO/SUPER VCD/VCD/CD PLAYER
CLEAR
SELECT
STROBE
4/¢
0 OPEN/CLOSE
7 STOP
3 PLAY
8 PAUSE
4
SKIP
¢
STANDBY/ON
STANDBY/ON
SLOW+
SLOW-
PROGRESSIVE DVD AUDIO
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
3D
PHONIC
ANGLE
ZOOM
AMP VOL
Basic operations
RM-SXV011J
REMOTE CONTROL
To locate a desired selection using 4 or ¢
Available :
¶ For DVD AUDIO/Audio CD: During playback or while stopped
For DVD VIDEO:
During playback
For SVCD/Video CD:
During playback without PBC function
Press 4 or ¢.
With a DVD AUDIO, pressing the button skips a group or track depending on the disc configuration. With a DVD
VIDEO, pressing the button skips a chapter or title depending on the disc configuration. With an SVCD, Video CD or
Audio CD, pressing the button skips a track.
The selection number appears in the display window on the front panel.
• To skip forward titles/chapters/groups/tracks, press ¢ as many times as required.
• To skip to the beginning of the current titles/chapters/groups/tracks, press 4 once.
• To skip back titles/chapters/groups/tracks, press 4 as many times as required.
NOTES
• This function may not work with some DVD VIDEO discs.
• This function does not work during SVCD/Video CD playback with PBC function (see pages 5 and 26).
22 From DvDPlayer-Manual.com JVC Manuals
Downloaded
Basic operations
English
To locate a desired selection using the numeric buttons
Available :
.
¶ For DVD AUDIO/DVD VIDEO/Audio CD:
For SVCD/Video CD:
During playback or while stopped
During playback without PBC function or while stopped
Use the numeric buttons to specify the number.
Unit status
While stopped
During playback
Disc type
What is specified
DVD AUDIO
group or track*1
DVD VIDEO
title or chapter*2
SVCD/Video CD/Audio CD
track
DVD AUDIO
track
DVD VIDEO
chapter
SVCD/ Video CD/Audio CD
track
*1 Pressing the numeric buttons simply selects a track. To select a group (When a disc contains more than one group),
press TITLE/GROUP before pressing the numeric buttons.
*2 Pressing the numeric buttons simply selects a chapter when a disc contains only one title, or selects a title when a
disc contains more than one title.
The selected title, group or track number appears in the display window on the front panel.
• To select a number between 1 and 10: Press the corresponding button for the number.
• To select a number higher than 10:
Use the +10 button.
Examples:
To select 13:
+10 → 3
To select 34:
+10 → +10 → +10 → 4
To select 40:
+10 → +10 → +10 → 10
The unit starts playback from the beginning of the selection. The selected title, chapter, group or track number
appears in the display window on the front panel.
NOTES
• You can also specify the desired title during DVD VIDEO playback. See page 27 for details.
• During DVD AUDIO/DVD VIDEO playback, if a menu is shown on the TV screen, the numeric buttons may be used for selecting
an item in the menu.
• When
appears on the TV screen:
The title, chapter, group or track you have selected is not contained in the disc.
• This function does not work during SVCD/Video CD playback with PBC function (see pages 5 and 26).
Downloaded From DvDPlayer-Manual.com JVC Manuals
23
Basic operations
Depending on the disc type and the unit status, what is specified differs.
Basic operations
Other convenient functions
You can check the playback status, as well as change the brightness of the display window.
Also, you can move back the playback position 10 seconds from the current position.
TV
TV
TV1
TV2
TV3
1
2
3
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
T
DVD
TV4
0
PAGE
RETURN
5/∞
DVD
STANDBY/ON
OPEN/
CLOSE
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
N
ON SCREEN
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
VFP
3
fs/Rate PROGRESSIVE
SCAN
DIGEST
3D
PHONIC
ANGLE
ZOOM
AMP VOL
ANGLE
RM-SXV011J
Basic operations
REMOTE CONTROL
To check the playback status
Available :
You can see the current selection number (the group/track number for DVD AUDIO, the title/chapter number for DVD
VIDEO or the track number for SVCD/Video CD/Audio CD), time information (the track, group or chapter time while
stopped, or the elapsed track, group or chapter time during playback) and the transport status (stop, playback, pause etc.)
on the TV screen.
¶ During playback or while stopped
Press ON SCREEN.
The playback status bar appears on the TV screen.
(for DVD AUDIO)
(for DVD VIDEO)
Current track
number
Transfer rate
8.5Mbps
Current transport
status
GROUP 3 TRACK 33
TOTAL 1:25:58
Current group number
Current chapter
number
Transfer rate
8.5Mbps
Current track
time
Current transport
status
TITLE 33 CHAP 33
TOTAL 1:25:58
Current title number Current chapter
time
(for Video CD)
(for SVCD)
Current transport
status
TRACK 33
TIME
Current track number
25:58
Disc elapsed
time
(for Audio CD)
Current transport status
TRACK 33
TIME
Current track number
24 From DvDPlayer-Manual.com JVC Manuals
Downloaded
25:58
Disc elapsed
time
Current transport
status
TRACK 33
Current track number
TIME
25:58
Disc elapsed
time
Basic operations
The indication on the right most of the status bar shows the unit's transport status as follows:
Icon
English
Status
Appears in the playback mode.
Appears in the stop mode.
Appears in the pause mode.
Appears in the fast forward/backward playback mode.
Appears in the slow-motion playback mode.
Note that pressing ON SCREEN again brings up the menu bar under the status bar, from which you can access
various functions.
(Example of the menu bar for DVD VIDEO)
TITLE 33 CHAP 33
8.5Mbps
OFF
CHAP.
1/3
TOTAL 1:25:58
1/5
1/3
See page 42 for details about the menu bar.
NOTES
Basic operations
• To dismiss the status bar:
Press ON SCREEN until the status bar is dismissed.
• The status bar cannot be displayed during MP3/JPEG playback.
To move back the playback position while DVD VIDEO playback
[One touch replay function]
Available :
During playback of a DVD VIDEO disc, you can move back the playback position 10 seconds from the current position.
¶ During DVD VIDEO playback
Press 3.
The playback position moves back 10 seconds before the current position.
Note that this function works only in the same title, though it works between chapters.
If you press 3 within 10 seconds from the beginning of a title, playback starts from the beginning of the title.
NOTES
• This function works only with DVD VIDEO discs.
• When
appears on the TV screen:
Some DVD VIDEO disc may not accept this function because of disc contents.
To change the brightness of the display window
You can dim the brightness of the display window.
Press 5 or ∞ while holding down ANGLE.
You can select the brightness of the display window from among three levels. Each time you press the button, the
brightness changes among low, middle, high, and off.
Downloaded From DvDPlayer-Manual.com JVC Manuals
25
Advanced operations
This chapter describes operations for various advanced
functions of DVD AUDIO, DVD VIDEO, SVCD, Video CD
and Audio CD discs. For MP3 and JPEG disc playback,
see the separate chapters on and after pages 47 and 51.
NOTE
TV
DVD
Make sure that the TV - DVD switch on
the remote control unit is set to “DVD”
when using the 5/∞/2/3, numeric and
TV/VIDEO - CANCEL buttons for
controlling the unit.
About DVD menu
Normally, a DVD AUDIO disc which contains more than one
group may have a “top” menu which lists the groups.
Similarly, a DVD VIDEO disc which contains more than one
title may have a “title” menu which lists the titles. In such a
case, the menu appears on the TV screen by pressing the TOP
MENU button. Some DVD AUDIO/DVD VIDEO discs may also
have a different menu which appears by pressing the MENU
button.
See the instructions of each DVD AUDIO/DVD VIDEO disc for its
particular menu.
Playing from a specific
position on a disc
You can play a disc from the selected track, title, group or
chapter, or from the specified time.
To locate a desired scene from the DVD
menu
Advanced
operations
Available :
DVD AUDIO/DVD VIDEO discs generally have their own
menus which show the disc contents. These menus
contain various items such as titles of movies, names of
songs, or artist information, and display them on the TV
screen. You can locate a desired scene by using the DVD
menu.
TV
• With some discs, you can also select items by entering the
corresponding number using the numeric buttons, which
may cause the unit to automatically start playback.
NOTES
• When
appears on the TV screen by pressing TOP
MENU or MENU in step 1:
The disc does not have an appropriate menu listing the
titles or groups.
• The MENU button does not work while stopped.
To locate a desired scene from the menu
of the SVCD/Video CD with PBC
DVD
TV2
TV3
1
2
3
TV4
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
10
PAGE
Available :
MUTING
0
RETURN
T
The unit starts playback of the selected item.
DVD
TV
TV1
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
ENTER
press ENTER.
STANDBY/ON
OPEN/
CLOSE
TOP
MENU
2 Use 5/∞/2/3 to select a desired item, then
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
N
MENU
5/∞/2/3
Some SVCD/Video CD discs support the PBC function.
PBC is an abbreviation of “PlayBack Control.“ An SVCD/
Video CD disc recorded with PBC has its own menus,
such as a list of the songs of the disc. You can locate a
specific scene by using the PBC menu.
STROBE
SLOW+
SLOW-
TV
REPEAT SUB TITLE AUDIO
DVD
STANDBY/ON
OPEN/
CLOSE
VFP
TV
DVD
fs/Rate PROGRESSIVE
SCAN
DIGEST
3D
PHONIC
ANGLE
ZOOM
TV1
AMP VOL
3
TV6
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
0
PAGE
RETURN
T
RETURN
TV3
2
TV5
4
10
RM-SXV011J
REMOTE CONTROL
TV2
1
TV4
OP
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
ME
NU
+
VOL-
¶ Whenever a DVD AUDIO/DVD VIDEO disc is loaded
1 Press TOP MENU or MENU.
The menu appears on the TV screen.
TOP
MENU
Numeric
buttons
VOL+
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
N
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
3
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
3D
PHONIC
ANGLE
ZOOM
AMP VOL
Example:
RM-SXV011J
REMOTE CONTROL
¶ When an SVCD/Video CD disc with PBC is stopped
26
Downloaded From DvDPlayer-Manual.com JVC Manuals
Advanced operations
1 Press 3 or TOP MENU.
A disc menu appears on the TV screen (the PBC
function is activated).
Example:
To specify a desired title/group
English
Available :
While playing back a DVD AUDIO/DVD VIDEO disc with
more than one title or one group, you can specify a
desired title or group to be played using the numeric
buttons.
TV
TV
TV1
TV2
front panel.
TV3
1
2
3
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
0
PAGE
RETURN
T
TITLE/
GROUP
DVD
TV4
10
“PBC“ is indicated in the display window on the
DVD
STANDBY/ON
OPEN/
CLOSE
Numeric
buttons
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
2 Use the numeric buttons to select the desired
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
item.
CLEAR
SELECT
STROBE
SLOW+
SLOW-
The unit starts playback of the selected item.
You can return to the menu by pressing the
RETURN button.
When something like “NEXT” or “PREVIOUS”
appears on the TV screen, the unit generally works
as follows:
• Pressing ¢ advances to the next page.
• Pressing 4 returns to the previous page.
* The method of the operation is different
depending on the disc.
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
ANGLE
3D
PHONIC
ZOOM
AMP VOL
RM-SXV011J
REMOTE CONTROL
¶ During playback
1 Press TITLE/GROUP.
“--” is shown in the title display area of the display
window.
(Display window example for DVD VIDEO)
LPCM VCDVD
GROUP TITLE TRACK CHAP
MPEG
DOLBY PROGRAM
DIGITAL
RANDOM
DTS
38
Title display area
Advanced
operations
• To select a number between 1 and 10:
Press the corresponding button for the number.
• To select a number higher than 10:
Use the +10 button.
Examples:
To select 13: +10 → 3
To select 34: +10 → +10 → +10 → 4
To select 40: +10 → +10 → +10 → 10
N
1 A-B
Current chapter number
2 Use the numeric buttons to specify a title or
group to be played.
• If you want to playback a PBC-compatible SVCD/Video CD
disc without activating the PBC function, start playback by
using the numeric buttons instead of 3 (see page 23).
• To activate the PBC function when a PBC-compatible SVCD/
Video CD disc is being played back without the PBC
function, carry out any of the followings:
* Press TOP MENU or MENU.
* Press 7 to stop playback, then press 3 .
• To select a number between 1 and 10:
Press the corresponding button for the number.
• To select a number higher than 10:
Use the +10 button.
Examples:
To select 13: +10 → 3
To select 34: +10 → +10 → +10 → 4
To select 40: +10 → +10 → +10 → 10
The unit starts playback from the specified title or
group.
NOTE
• Some DVD AUDIO/DVD VIDEO discs may not accept
this function because of disc contents.
Downloaded From DvDPlayer-Manual.com JVC Manuals
27
Advanced operations
To locate a desired position in the
current title, group or track [Time
search]
Available :
TV
TIME _ : _ _ : _ _
TV2
TV3
1
2
3
TV5
TV6
4
5
TV7
TV8
→
8
9
TV0
MUTING
10
0
+10
PAGE
Numeric
buttons
6
TV9
7
TV-/--
Press “2”.
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
TIME 2 : 3 4 : _ _
VOL+
ENTER
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
ON SCREEN
N
→
CH
-
Press ENTER.
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
VFP
• Example (for SVCD/Video CD/Audio CD)
To play back from 23(M):40(S)
fs/Rate PROGRESSIVE
SCAN
DIGEST
Press “4”.
ME
NU
VOL-
CH
OIC
E
Press “3”.
TIME 2 : 3 _ : _ _
→
T
• Example (for DVD AUDIO/DVD VIDEO)
To play back from 2(H):34(M):00(S)
DVD
TV4
RETURN
Advanced
operations
The unit starts playback from the specified time.
TIME 2 : _ _ : _ _
DVD
TV
TV1
ENTER
4 Press ENTER.
STANDBY/ON
OPEN/
CLOSE
2/3
• You can specify the time in hour/minute/second format for
DVD AUDIO/DVD VIDEO discs, and in minute/second
format for SVCD/Video CD and Audio CD discs.
→
You can play a disc from the desired position by
specifying the elapsed time from the beginning of the
current group (for DVD AUDIO), the current title (for DVD
VIDEO) or the disc (for SVCD/Video CD/Audio CD) using
the time search function.
Note that some DVD VIDEO discs do not contain time
information, and the time search function cannot be
used.
• “10” button works as “0” and “+10” button is not used with
this function.
ANGLE
3D
PHONIC
ZOOM
AMP VOL
TIME
RM-SXV011J
REMOTE CONTROL
__:__
→
¶ For DVD AUDIO/DVD VIDEO/Audio CD:
TIME
1 Press ON SCREEN twice.
TIME
to
Press “3”.
23:__
Press “4”.
23:4_
→
The menu bar appears on the TV screen.
(See page 42 for details about the menu bar.)
2 Use 2/3 to move
TIME
→
In any condition except SVCD/Video CD
playback with PBC
2_:__
→
During playback or while stopped
¶ For SVCD/Video CD:
Press “2”.
Press ENTER.
, then press
You do not have to press “0” to enter the trailing zeros
(for the last two digits in the example above).
The pull-down menu for entering time appears
under the
.
• When you correct a mistake
Use 2 repeatedly to move back to the digit where you
entered a undesired numeral (the leftmost “-” digit),
and reenter the correct time.
ENTER.
(Screen example for DVD VIDEO)
TITLE 33 CHAP 33
8.5Mbps
OFF
CHAP.
TIME
1/3
TOTAL 1:25:58
1/5
1/3
(Example for changing “2:35:__” to “2:34:__.”)
_:__:__
TIME 2 : 3 5 : _ _
TRACK 33
OFF
→
(Screen example for Audio CD)
TIME
25:58
PROG. RND.
__:__
3 Use the numeric buttons (0 to 10) to enter the
desired time.
The specified time is displayed in the pull-down
menu.
28
Downloaded From DvDPlayer-Manual.com JVC Manuals
TIME 2 : 3 _ : _ _
→
TIME
Press 2.
Press “4”.
TIME 2 : 3 4 : _ _
Advanced operations
NOTES
Disc type
Unit status
What is displayed
While stopped
The opening scene of
each title
DVD
VIDEO
During playback
The opening scene of
each chapter in the
current title
SVCD/
Video CD
While stopped or
during playback
The opening scene of
each track
• When a DVD AUDIO disc is stopped, you can specify the
elapsed time from the beginning of group 1.
• When
appears on the TV screen:
The time you have selected is not contained on the disc,
or the time search function does not work on the disc.
Also note that the time search function does not work
during SVCD/Video CD playback with the PBC function.
• To dismiss off the menu bar:
English
Press ON SCREEN.
• The time search function cannot be used during
program playback.
To locate a desired scene from the
display [DIGEST]
2 Use 5/∞/2/3 to move
to the desired
scene.
If there are more than nine scenes, the digest
screen will have more than one page. In this case,
pressing ¢ advances to the next page, and
pressing 4 returns to the previous page.
Available :
The unit can display the opening scene of each title or
chapter on a DVD VIDEO or each track of an SVCD/Video
CD. You can select a desired scene from those displayed
on the TV screen.
Selected scene
TV
DVD
TV2
1
2
TV3
3
TV4
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
PAGE
OP
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
ME
NU
+
VOL-
VOL+
ENTER
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
• When the lower right scene is selected, pressing 3
advances to the next page if available. Similarly, when the
upper left scene is selected, pressing 2 returns to the
previous page (if available).
SELECT
5/∞/2/3
N
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
DIGEST
3D
PHONIC
ANGLE
ZOOM
AMP VOL
Advanced
operations
TV
TV1
RETURN
T
DVD
STANDBY/ON
OPEN/
CLOSE
• Depending on discs, it may take some time until all scenes
of the current page appear on the TV screen. If you want to
turn the page, you do not have to wait to press 4 or ¢
until all scenes appear.
3 Press ENTER.
The unit starts playback from the selected scene.
RM-SXV011J
REMOTE CONTROL
¶ For DVD VIDEO:
During playback or while stopped
For SVCD/Video CD: In any condition except
SVCD/Video CD playback
with PBC
NOTE
• With some discs, depending on the contents, it may
take some time until all the scenes appear on the
screen.
1 Press DIGEST.
Up to nine opening scenes are displayed.
Depending on the disc type and whether the disc is
being played back or not, the contents shown on
the TV screen differ.
Downloaded From DvDPlayer-Manual.com JVC Manuals
29
Advanced operations
To select a still picture on a DVD AUDIO
disc [PAGE]
To play back a bonus group of a DVD
AUDIO disc
Available :
Most DVD AUDIO discs include still pictures, which
usually appear in turn automatically during playback
according to the playback sequence. However, there are
other page(s) of the current still picture and you can
change the picture (turn the page) manually.
• At the beginning of a part where there are selectable
pictures, “PAGE” appears on the TV screen (except when
the “ON SCREEN GUIDE” preference is set to “OFF”). See
page 63 for details about “ON SCREEN GUIDE”
preferences.
TV
DVD
TV
TV1
TV
TV2
TV3
TV
TV1
DVD
TV2
TV3
1
2
3
1
2
3
TV5
TV6
TV4
TV5
TV6
4
5
6
4
5
6
TV7
TV8
TV9
TV7
TV8
TV9
7
8
9
7
8
9
TV-/--
TV0
MUTING
TV-/--
TV0
MUTING
10
0
+10
10
0
+10
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL+
ENTER
PAGE
RETURN
5/∞
T
PAGE
TITLE/
GROUP
VOL-
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
SELECT
SLOW-
ME
NU
VOL-
VOL+
CH
OIC
E
N
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
STROBE
CLEAR
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
VFP
SELECT
3D
PHONIC
ANGLE
SLOW+
DIGEST
AMP VOL
3D
PHONIC
ANGLE
ZOOM
AMP VOL
RM-SXV011J
RM-SXV011J
REMOTE CONTROL
REMOTE CONTROL
1 Press PAGE.
VFP
fs/Rate PROGRESSIVE
SCAN
ZOOM
¶ During playback
(except when the status bar is shown)
N
STROBE
REPEAT SUB TITLE AUDIO
fs/Rate PROGRESSIVE
SCAN
DIGEST
Numeric
buttons
TV/VIDEO
CANCEL
ENTER
PREVIOUS
CLEAR
TITLE/
GROUP
NU CH
ME
+
OP
ENTER
Advanced
operations
DVD
STANDBY/ON
OPEN/
CLOSE
DVD
TV4
RETURN
T
Some DVD AUDIO discs contain a special group called
“bonus group” whose contents are not opened to the
public. The bonus group is always assigned to the last
group of a disc (for example, if a disc contains four
groups including a bonus group, “group 4” is the bonus
group).
To play back a bonus group, you have to enter the
specific “key number” (a kind of password) for the
bonus group. A way of getting the key number depends
on discs.
After getting the key number, you can play back the
bonus group by the following procedure.
STANDBY/ON
OPEN/
CLOSE
PAGE
Available :
¶ While a disc containing a bonus group is stopped
1 Use the numeric buttons to select the bonus
group number (the last group).
The Page selection window appears on the TV
screen.
PAGE 1/32
The display window and on-screen display prompt
you to enter the key number as shown below.
(Display Window)
(TV screen)
1
KEY
2 Use PAGE or 5/∞ to select the desired page.
Each time you press PAGE or 5/∞, the page
number changes.
3 Press ENTER.
The selected page (picture) is shown.
The Page selection window is dismissed.
NOTE
• The Page selection window will automatically
disappear if you do not change the page for several
seconds.
• You can also select the page via the menu bar.
See page 44.
30
Downloaded From DvDPlayer-Manual.com JVC Manuals
____
2 Use the numeric buttons (0 to 9) to enter the
key number.
If you enter the key number correctly, the unit starts
playback of the bonus group.
If you enter a wrong key number, the unit does not
start playback and the display window and TV
screen again prompt you to reenter the key
number.
Advanced operations
NOTE
• Once you enter the correct key number, the unit
memorizes it until you turn off the power or open the
tray.
Changing the playback
order
• If you specify a track in the bonus group when
programming tracks for the program playback, the
display window will also show the above display for
inquiring the key number.
You can play tracks on a DVD AUDIO, SVCD, Video CD or
Audio CD in the desired order or in random order.
• In the random playback mode, tracks in the bonus
group are not played back.
To play back in the desired order
[Program playback]
• To turn off the key number entry display, operate any
one of the following.
* Press 7 .
Available :
* Open the disc tray.
* Turn the power off.
Opening the disc tray or turning the power off also
erases the memory of the key number, while pressing 7
does not erase the memory.
English
By programming tracks, you can play up to 99 tracks in
any order. You may program the same track more than
once.
TV
TV
TV1
2/3
DVD
TV2
TV3
1
2
3
TV4
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
+10
PAGE
RETURN
T
DVD
STANDBY/ON
OPEN/
CLOSE
TITLE/
GROUP
Numeric
buttons
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
7
CLEAR
SELECT
ON SCREEN
N
3
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
Advanced
operations
CH
OIC
E
ENTER
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
ANGLE
3D
PHONIC
ZOOM
AMP VOL
RM-SXV011J
REMOTE CONTROL
¶ While stopped
1 Press ON SCREEN twice.
The menu bar appears on the TV screen.
(See page 42 for details about the menu bar.)
2 Use 2/3 to move
to
PROG.
.
(Screen example for DVD AUDIO)
GROUP 3 TRACK 33
8.5Mbps
O FF
TRACK
PROG. RND.
TOTAL 1:25:58
1/3
PAGE 32/32
3 Press ENTER.
The program table appears instead of the menu bar.
The PROGRAM indicator lights in the display
window on the front panel.
(Program table example for DVD AUDIO)
Total Program Time
PROGRAM
No.
Group
1
2
3
4
5
6
7
8
9
10
00:00:00
Track
-
USE NUMERIC KEYS TO PROGRAM TRACKS.
CANCEL DELETES THE LAST STEP. 7 DELETES ALL.
Downloaded From DvDPlayer-Manual.com JVC Manuals
31
Advanced operations
4 a (for DVD AUDIO)
Specify selections in the desired order by
group and track numbers using the numeric
buttons.
• For each program step, using the numeric
buttons, specify a group first, then specify a track.
• For example, to specify “track 14 in group 2,”
Press 2 → +10 → 4.
4 b (for SVCD/Video CD/Audio CD)
Specify tracks in the desired order using the
numeric buttons.
• To select a number between 1 and 10:
Press the corresponding button for the number.
• To select a number higher than 10:
Use the +10 button.
Examples:
To select 13: +10 → 3
To select 34: +10 → +10 → +10 → 4
To select 40: +10 → +10 → +10 → 10
Advanced
operations
Up to 99 tracks can be programmed. You may
select the same track more than once.
The total program time is shown at the right top of
the program table.
(Program table example for DVD AUDIO)
The total program time
Total Program Time
PROGRAM
No.
1
2
3
4
5
6
7
8
9
10
2
3
7
4
3
5
6
Group
1
5
4
2
3
4
6
00:25:12
TrackDisc
- 9
- 12
- 6
- 8
- 6
- 14
- 20
• To quit program playback
Press 7. Note that the program remains.
• To clear the program
While stopped and the program table is shown on the
TV screen, press 7.
All the programmed tracks are erased.
• To exit the program mode
After clearing all programmed tracks, press ON
SCREEN.
The program table is dismissed and the status bar
appears on the TV screen.
The PROGRAM indicator in the display window
disappears and the unit quits program playback
mode.
NOTES
• During program playback, you cannot edit the program
contents.
• During program playback, pressing ¢ skip to the next
selection of the program. Pressing 4 returns to the
beginning of the current selection.
• If you are going to program a track in the bonus group
of a DVD AUDIO, the unit will ask you to enter the key
number for the bonus group (see page 30).
• To dismiss the program table:
Press ON SCREEN. The program table is dismissed and
the status bar is shown.
• To dismiss the menu bar (and the status bar):
Press ON SCREEN.
USE NUMERIC KEYS TO PROGRAM TRACKS.
CANCEL DELETES THE LAST STEP. 7 DELETES ALL.
Selected group/track number
• If you specify a wrong track
Use 5/∞ to move
to the wrong track, then
press TV/VIDEO - CANCEL. The track is erased
and the subsequent programmed tracks move up.
• To clear the program while programming
Press 7.
5 Press 3 to start program playback.
With a DVD AUDIO/SVCD/Video CD disc, the
program table is automatically dismissed when the
program playback starts.
With an Audio CD disc, the program table remains
on the TV screen during program playback.
However, pressing the ON SCREEN button brings
up the status bar.
When all of the programmed tracks have finished
playback, the unit stops and the program table
appears again.
Note that the program remains.
32
• To check the program contents
During playback, press 7. Playback stops and the
program table is shown.
When the unit is playing back an Audio CD and the
program table is not shown, you can bring up the
table by carrying out steps 1 to 3.
During DVD AUDIO/SVCD/Video CD playback, you
cannot see the program table during playback.
Downloaded From DvDPlayer-Manual.com JVC Manuals
Advanced operations
To play back in random order
[Random playback]
Repeat playback
Available :
You can play tracks on a disc in random order by using
the random function.
TV
2/3
TV
DVD
TV1
TV2
1
2
3
TV4
TV5
TV6
4
5
6
TV8
TV9
8
9
TV0
MUTING
10
0
+10
OP
To repeat the current selection or all
tracks [Repeat playback]
Available :
7
TV-/--
PAGE
You can repeat playback of the current group or track (for
DVD AUDIO), current title or chapter (for DVD VIDEO) or
current or all tracks (for SVCD/Video CD/Audio CD).
You can also repeat playback of a desired part.
TV3
TV7
RETURN
T
DVD
STANDBY/ON
OPEN/
CLOSE
TITLE/
GROUP
TV
TV/VIDEO
CANCEL
NU CH
ME
+
ENTER
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
TV
TV1
VOL+
ENTER
ON SCREEN
N
TV2
TV3
1
2
3
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
PAGE
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
STROBE
T
SELECT
DVD
TV4
RETURN
CLEAR
DVD
STANDBY/ON
OPEN/
CLOSE
ME
NU
VOL-
CH
OIC
E
English
SLOW+
SLOW-
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
REPEAT SUB TITLE AUDIO
VFP
CH
OIC
E
fs/Rate PROGRESSIVE
SCAN
ANGLE
ZOOM
E
RE
SC
ON
NEXT
PREVIOUS
3D
PHONIC
CLEAR
SELECT
STROBE
SLOW+
SLOW-
RM-SXV011J
REPEAT
REMOTE CONTROL
REPEAT SUB TITLE AUDIO
1 Press ON SCREEN twice.
ANGLE
to
AMP VOL
RM-SXV011J
RND.
.
(Screen example for Audio CD)
TRACK 33
PROG.
ZOOM
REMOTE CONTROL
The menu bar appears on the TV screen.
(See page 42 for details about the menu bar.)
2 Use 2/3 to move
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
3D
PHONIC
¶ While stopped
OFF
N
AMP VOL
TIME
25:58
RND.
3 Press ENTER.
The unit starts random playback.
With a DVD AUDIO/SVCD/Video CD disc, the menu
bar is automatically dismissed.
During random playback, the RANDOM indicator
lights in the display window on the front panel.
After playing all tracks of the disc, the unit stops the
disc and quits the random mode.
• The same track will not be played back more than once
during random playback.
• During random playback, if you bring up the menu bar and
carry out steps 1 to 3 above, the unit cancels the random
playback mode and continues playback from the current
selection in the recorded order.
• In the random playback mode with the DVD AUDIO, tracks
in the bonus group are not played back (see page 30).
• To stop and quit random playback
Press 7. The unit stops playback and quits the
random playback mode.
NOTE
• To dismiss the menu bar:
Press ON SCREEN.
Downloaded From DvDPlayer-Manual.com JVC Manuals
¶ For DVD AUDIO/DVD VIDEO:
During playback or while stopped
For SVCD/Video CD/Audio CD:
In any condition except SVCD/
Video CD playback with PBC
Advanced
operations
DIGEST
CH
-
1 Press REPEAT.
Each time you press REPEAT, the repeat mode
switches among All repeat, Repeat 1 and off.
You can see the selected mode by icons in the
display window on the front panel as below.
If you press REPEAT while stopped, you need to
press 3 to start repeat playback.
:
Repeats the current group for DVD AUDIO,
the current title for DVD VIDEO, or all
tracks for SVCD/Video CD/Audio CD.
: Repeats the current track for DVD
AUDIO/SVCD/Video CD/Audio CD or the
current chapter for DVD VIDEO.
No indication:
The repeat mode is off.
(Display window)
LPCM VCDVD
GROUP TITLE TRACK CHAP
MPEG
DOLBY PROGRAM
DIGITAL
RANDOM
DTS
38
1 A-B
Repeat mode indicators
On the TV screen, a window for repeat mode
indication appears. You can check the current
repeat mode from the window.
The mode indication on the window is the same as
the one on the menu bar (see pages 43, 44 and 45).
(Screen example for repeat mode indication window.)
CHAP.
33
Advanced operations
• To stop repeat playback
Press 7.
When a DVD AUDIO, SVCD, Video CD or Audio CD
disc is set, the unit stops playback but does not quit
the repeat mode.
When a DVD VIDEO disc is set, the unit stops playback
and quits the repeat mode.
3 Use 5/∞
to select “A-B.”
Depending on the disc type and unit’s status the
repeat mode changes as follows:
• During DVD AUDIO playback
GROUP 3 TRACK 33
8.5Mbps
TRACK
• To quit repeat playback
Press REPEAT until the repeat mode indicator goes off
in the display window.
TOTAL 1:25:58
1/3
PROG. RND.
PAGE 32/32
A-B
Selected repeat mode
NOTES
TRACK :
current track repeat
GROUP :
current group repeat
A-B :
repeats a desired part
(during playback only)
• You can also select the repeat mode via the menu bar.
See pages 43, 44 and 45.
• When the program playback mode is active with a DVD
AUDIO, SVCD, Video CD or Audio CD, the repeat mode
changes in the same manner.
Note that, however, in the “
” mode the unit repeats all
the programmed tracks, instead of all tracks on the disc.
• During playback in the title/chapter/group/track repeat
mode, if you skip the title/chapter/group/track using
4/¢, etc., the destination title/chapter/group/track is
repeated.
OFF
• During DVD VIDEO playback
• If
appears when pressing REPEAT during DVD VIDEO
playback
Advanced
operations
You cannot repeat the title or chapter because of the disc
contents.
• Repeat playback function cannot be used during SVCD/
Video CD playback with PBC function.
Available :
1/3
TOTAL 1:25:58
1/5
1/3
A-B
Selected repeat mode
TITLE :
current title repeat
A-B :
repeats a desired part
(during playback only)
DVD
STANDBY/ON
OPEN/
CLOSE
TV
TV1
DVD
TV2
TV3
1
2
3
TV4
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
10
OFF
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
• During SVCD/Video CD/Audio CD playback
MUTING
0
PAGE
RETURN
T
CHAP.
CHAPTER :current chapter repeat
To repeat a desired part
[A-B repeat playback]
TV
TITLE 33 CHAP 33
8.5Mbps
SELECT
N
5/∞/2/3
ON SCREEN
(Screen example for Audio CD)
TRACK 33
PROG.
STROBE
TIME
RND.
SLOW+
SLOW-
A-B
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
ANGLE
3D
PHONIC
ZOOM
AMP VOL
Selected repeat mode
TRACK : current track repeat
RM-SXV011J
REMOTE CONTROL
¶ During playback except SVCD/Video CD playback
with PBC
1 Press ON SCREEN twice.
ALL :
all track repeat
A-B :
repeats a desired part
(during playback only)
The menu bar appears on the TV screen.
(See page 42 for details about the menu bar.)
2 Use 2/3 to move
to
, then press
ENTER.
The pull-down menu for repeat mode selection
appears under the
.
34
Downloaded From DvDPlayer-Manual.com JVC Manuals
OFF
25:58
Advanced operations
4 Press ENTER at the beginning of the part you
want to repeat (point A).
The pull-down menu turns off.
A- .
The repeat icon shows
(Screen example for DVD VIDEO)
TITLE 33 CHAP 33
8.5Mbps
A-
CHAP.
1/3
1/5
TOTAL 1:25:58
1/3
Repeat icon
5 Press ENTER at the end of the part you want
to repeat (point B).
A-B .
The repeat icon shows
The unit locates “A” and starts repeat playback
between “A” and “B.”
• To quit A-B repeat playback
Press ENTER. The A-B repeat mode turns off, while the
playback continues.
Changing the language,
sound and scene angle
English
With some DVD AUDIO/DVD VIDEO discs, you can
choose a desired subtitle language and/or audio
language/sound, as well as a desired camera angle.
Some DVD AUDIO discs support more than one audio
language/sound, with some DVD VIDEO discs support
more than one subtitle language and/or audio language/
sound.
Similarly, you can choose a desired audio channel (or
channel combination) of an SVCD/Video CD disc, as well
as a subtitle channel of an SVCD disc.
To select the subtitle language
[SUB TITLE]
Available :
• Selecting “OFF” from the pull-down menu for repeat mode
selection, or pressing 4/¢ quits the A-B repeat mode
and continues playback.
Some DVD AUDIO, DVD VIDEO and SVCD discs for
movies, guides, etc. contain more than one subtitle
language. You can choose a desired one from them.
NOTES
• The A and B points must be set in the same title/
chapter/group/track.
• At the beginning of the part where the subtitle(s) is(are)
recorded,
appears on the TV screen (except when the
“ON SCREEN GUIDE” preference is set to “OFF”). See page
63 for details about “ON SCREEN GUIDE” preference.
Advanced
operations
• You can also stop and quit the A-B repeat mode by pressing
7.
• To dismiss the menu bar:
Press ON SCREEN.
TV
TV
TV1
You cannot repeat the selected portion because of the
disc contents.
DVD
TV2
TV3
1
2
3
TV4
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
+10
PAGE
RETURN
T
DVD
STANDBY/ON
OPEN/
CLOSE
• If
appears when pressing ENTER during DVD VIDEO
playback
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
ENTER
VOL+
5/∞
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
SUB TITLE
N
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
3D
PHONIC
ANGLE
ZOOM
AMP VOL
RM-SXV011J
REMOTE CONTROL
¶ During DVD AUDIO/DVD VIDEO/SVCD playback
(except when the status bar is shown)
1 Press SUB TITLE.
The Subtitle selection window appears on the TV
screen.
1/3
ENGLISH
Downloaded From DvDPlayer-Manual.com JVC Manuals
35
Advanced operations
2 Use SUB TITLE or 5/∞ to select the subtitle.
Each time you press SUB TITLE or 5/∞, the subtitle
language changes.
See the following examples for subtitle selection.
• For DVD AUDIO/DVD VIDEO
Pressing SUB TITLE or 5/∞ cycles among the
subtitles recorded on the disc.
Example:
1/3 ENGLISH
2/3 FRENCH
To change the audio language or sound
[AUDIO]
Available :
By audio selection, you can choose the audio language of
movies or enjoy KARAOKE with or without the vocal.
• At the beginning of the part where multiple audio sounds
are recorded,
appears on the TV screen (except when
the “ON SCREEN GUIDE” preference is set to “OFF”). See
page 63 for details about “ON SCREEN GUIDE” preference.
3/3 SPANISH
TV
-/3 OFF
For SVCD
An SVCD disc can have up to four subtitles.
Pressing 5/∞ cycles among those channels as
follows regardless of whether the subtitles are
recorded or not.
TV
TV1
DVD
TV2
TV3
1
2
3
TV4
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
+10
PAGE
RETURN
T
•
DVD
STANDBY/ON
OPEN/
CLOSE
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
-/4 OFF
SELECT
N
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
Advanced
operations
5/∞
ENTER
3D
PHONIC
1/4
ANGLE
ZOOM
AUDIO-fs/Rate
AMP VOL
RM-SXV011J
REMOTE CONTROL
2/4
3/4
4/4
3 Press ENTER.
¶ During playback
(except when the status bar is shown)
1 Press AUDIO-fs/Rate.
The Audio selection window appears on the TV
screen.
The subtitle in the selected language is shown.
The Subtitle selection window is dismissed.
1/3
ENGLISH
NOTES
• For DVD VIDEO, the selected language may be abbreviated
on the TV screen. See “Table of languages and their
abbreviations” on page 58.
• The Subtitle selection window will automatically
disappear if you do not change the subtitle for several
seconds.
• When
appears on the TV screen (for DVD AUDIO/
DVD VIDEO disc):
You cannot select the subtitle or no subtitle is recorded.
• You can also select the subtitle via the menu bar. See
pages 45 and 46.
2 Use AUDIO-fs/Rate or 5/∞ to select the
desired audio.
Each time you press AUDIO-fs/Rate or 5/∞, the
audio changes.
See the following examples for audio selection.
• For DVD AUDIO/DVD VIDEO
Each time you press AUDIO-fs/Rate or 5/∞, the
audio language or sound changes.
Example:
1/3 ENGLISH
2/3 FRENCH
3/3 SPANISH
36
Downloaded From DvDPlayer-Manual.com JVC Manuals
Advanced operations
• For SVCD/Video CD
Each time you press AUDIO-fs/Rate or 5/∞, the playback
audio changes as follows.
TV
(for Video CD)
ST1
TV
TV1
ST (stereo)
TV2
T
TV3
1
2
3
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
L
DVD
TV4
0
PAGE
RETURN
ST2
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
L-1
DVD
STANDBY/ON
OPEN/
CLOSE
R
CLEAR
SELECT
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
5/∞/2/3
N
3
VFP
fs/Rate PROGRESSIVE
SCAN
R-1
DIGEST
ANGLE
3D
PHONIC
L-2
ANGLE
ZOOM
AMP VOL
RM-SXV011J
REMOTE CONTROL
R-2
From Angle selection window
3 Press ENTER.
You can hear the selected audio.
The audio selection window is dismissed.
NOTES
• For DVD VIDEO, the selected language may be abbreviated
on the TV screen. See “Table of languages and their
abbreviations” on page 58.
¶ During DVD VIDEO playback
(except when the status bar is shown)
1 Press ANGLE.
The Angle selection window appears on the TV
screen.
1/3
• The Audio selection window will automatically
disappear if you do not change the audio for several
seconds.
1
Advanced
operations
(for SVCD)
English
• When
appears on the TV screen (for a DVD AUDIO/
DVD VIDEO disc):
You cannot select the audio.
• If only one audio sound is recorded, you cannot select
the audio.
• You can also select the audio via the menu bar. See
pages 44, 45 and 46.
To select a scene angle of DVD VIDEO
[ANGLE]
2 Use ANGLE or 5/∞ to select the desired
angle.
Each time you press ANGLE or 5/∞, the angle
changes.
Example:
1/3
2/3
Available :
You can enjoy a variety of scene angles if the DVD VIDEO
disc contains “multi-angle” parts, where multiple
cameras were used to shoot the same scene from
different angles.
3/3
3 Press ENTER.
You can see the picture from the selected angle.
The Angle selection window is dismissed.
• At the beginning of a “multi-angle” part,
appears on the
TV screen (except when the “ON SCREEN GUIDE”
preference is set to “OFF”). See page 63 for details about
“ON SCREEN GUIDE” preference.
Downloaded From DvDPlayer-Manual.com JVC Manuals
37
Advanced operations
From the angle list
¶ During DVD VIDEO playback
1 Press and hold ANGLE for more than 1
second.
Up to nine camera angles recorded on a disc
appear on the TV screen.
Special picture playback
and picture/sound effect
You can see continuous still pictures or zoom in (or out) the
picture. You can also adjust the picture character, as well as
simulate surround sound using a stereo system.
To display continuous still pictures
[STROBE]
Available :
The selected camera angle
T
RETURN
2 Use 5/∞/2/3 to select the desired angle.
3 Press ENTER or 3.
The unit starts playback by the selected angle on
the full-sized screen.
Advanced
operations
NOTES
• The Angle selection window will automatically
disappear if you do not change the angle for several
seconds.
• When
appears on the TV screen in step 1:
The current scene is not recorded from multiple angles.
PAGE
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
N
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
8/STROBE
VFP
fs/Rate PROGRESSIVE
SCAN
¶ During playback
DIGEST
ANGLE
ZOOM
1 At the point you want to view as continuous
photographs, press 8/STROBE.
The unit pauses playback.
2 Press and hold 8/STROBE for more than 1
second.
• During the operation from the angle list display, audio is
muted.
Nine same frames (still pictures) appear on the TV
screen.
You can advance frames one by one by the
following step.
• You can also select the angle via the menu bar. See
page 45.
3
Press 8/STROBE once.
The picture in the middle on the top row shows an
advanced frame from one in the left.
Advanced frame
Each press of 8/STROBE advances the frames one
by one.
Pressing 3 instead of 8/STROBE advances each
frame in normal playback speed with a time delay
over the whole nine pictures (while the sound is
muted).
• To return to the normal screen
Press and hold 8/STROBE for more than 1 second.
NOTE
• If you press and hold 8/STROBE for more than 1 second
during playback, nine still pictures also appear but they
advance in normal playback speed (while the sound is
muted).
38
Downloaded From DvDPlayer-Manual.com JVC Manuals
Advanced operations
To zoom in/out pictures [ZOOM]
To adjust the picture character [VFP]
Available :
T
Available :
OP
NU CH
ME
+
ME
NU
VOL-
VOL+
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
5/∞/2/3
N
The VFP (Video Fine Processor) function allows you to
adjust the picture character according to the type of
programming, picture tone or personal preferences.
STROBE
SLOW+
SLOW-
TV
REPEAT SUB TITLE AUDIO
ANGLE
3D
PHONIC
DVD
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
English
ZOOM
STANDBY/ON
OPEN/
CLOSE
ZOOM +/–
TV
TV1
TV2
2
3
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
REMOTE CONTROL
PAGE
1 Press ZOOM + or −.
The unit zooms in by pressing ZOOM + or zooms
out by pressing ZOOM −.
Each time you press ZOOM +, the magnification is
doubled (up to x 1024).
Each time you press ZOOM −, the magnification is
halved (down to x 1/8).
T
RETURN
¶ During playback or while paused
ENTER
TV3
1
TV4
AMP VOL
RM-SXV011J
DVD
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
5/∞/2/3
N
ANGLE
3D
PHONIC
ZOOM
AMP VOL
VFP PROGRESSIVE
SCAN
RM-SXV011J
REMOTE CONTROL
1 Press VFP - PROGRESSIVE SCAN.
The VFP mode selection window appears on the TV
screen.
Advanced
operations
¶ During playback (for DVD VIDEO: During playback
while picture is shown)
2 Use 2/3 to select the desired preset.
ZOOM x 4
Each time you press the button, the VFP mode
changes as follows.
Set the video type most suitable to the current
program or the room conditions.
Selected preset
NORMAL
At the top-left of the screen, the information for the
current magnification appears. While zoomed in,
the indication for the zoomed-in position, which
can be moved by operating the next step, appears
together.
2 Use 5/∞/2/3 to move the zoomed position.
USER 1
GAMMA
+ 0
BRIGHTNESS
+ 0
CONTRAST
+10
SATURATION
+10
TINT
+10
SHARPNESS
+ 0
Y DELAY
+ 0
CINEMA
USER 1
Parameter
USER 2
ZOOM x 4
NOTES
• To return to normal playback
Press ENTER.
“NORMAL” is suitable for watching TV in a general
room. “CINEMA” is suitable for watching a movie
software in a room with suppressed light.
They are factory presets and you cannot change
parameters for them.
While selecting “USER 1” or “USER 2,” you can
adjust parameters that affect the picture character
and store the settings as the user preset. See the
next step.
• While zoomed, the picture may look coarse.
• The zoom information on the screen will disappear if
you do not operate the zoom function for five seconds.
• The zoom information appears again when you press
ZOOM +/−, or 5/∞/2/3.
Downloaded From DvDPlayer-Manual.com JVC Manuals
39
Advanced operations
3 To define a user setting, select a parameter to
be edited using 5/∞ from the followings.
• GAMMA
Controls the brightness of a shaded portion
without changing the brightness of the entire
picture.
This control is optimum when you adjust the
pictures of software which generates subdued
black in a bright room.
The setting range is +4 to -4.
• BRIGHTNESS
Controls the brightness of the screen.
The setting range is +16 to -16.
• CONTRAST
Controls the contrast of the screen.
The setting range is +16 to -16.
NOTES
• The number of setting steps depends on parameters.
• To dismiss the VFP mode selection window:
Press VFP - PROGRESSIVE SCAN.
• The window for VFP mode selection and parameter
setting disappears if no operation is made for about 10
seconds.
• The VFP function cannot be used during JPEG playback.
To simulate surround sound
[3D PHONIC]
Available :
Using the 3D PHONIC function, you can get a simulated
surround effect from your stereo system.
Advanced
operations
• SATURATION
Controls the color depth of the screen.
The setting range is +16 to -16.
STANDBY/ON
OPEN/
CLOSE
TV
TV2
1
2
3
TV4
TV5
TV6
4
5
6
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
0
PAGE
RETURN
T
TV3
TV7
10
• TINT
Controls the tint of the screen.
Use the appearance of a natural complexion as
the guideline.
The setting range is +16 to -16.
DVD
TV1
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
STROBE
SLOW+
SLOW-
• SHARPNESS
Controls the sharpness of the screen.
The setting range is +3 to 0.
• Y DELAY
Controls the color gap of the screen.
The setting range is +2 to -2.
5/∞/2/3
N
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
ANGLE
3D
PHONIC
3D PHONIC
ZOOM
AMP VOL
RM-SXV011J
REMOTE CONTROL
¶ During playback
1 Press 3D PHONIC.
4 Press ENTER.
A window for setting parameters appears instead
of the VFP mode selection window.
The 3D PHONIC window appears on the TV screen.
2 Use 2/3 to select the desired mode.
Each time you press the button, the 3D PHONIC
mode changes as follows:
SATURATION
ACTION
++ 45
DRAMA
Selected parameter
ACTION
+45
5 Use 5/∞ to adjust the level of the parameter.
The higher value enhances the effect.
6 Press ENTER.
The parameter is set and the VFP mode selection
window appears again.
Repeat steps 3 to 6 if you want to set other
parameters.
THEATER
Selected effect mode
NONE
• ACTION
Suitable for action movies and sports programs
in which sounds dynamically move.
• DRAMA
Natural and warm sound. You can enjoy movies
in a relaxed mood.
• THEATER
You can enjoy sound effects like in a major
theater in Hollywood.
40
Downloaded From DvDPlayer-Manual.com JVC Manuals
Advanced operations
3 Press 5/∞ to adjust the effect level.
You can select the effect level among “1” to “5.”
The higher value enhances the effect.
ACTION
+45
Checking the sampling
frequency and bit rate
English
Available :
You can check the sampling frequency and bit rate of
digital audio during playback.
TV
Effect level
.
TV
TV1
NOTES
TV2
T
TV3
1
2
3
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
0
PAGE
RETURN
Press 3D PHONIC.
DVD
TV4
10
• To dismiss the 3D PHONIC window:
DVD
STANDBY/ON
OPEN/
CLOSE
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
• The 3D PHONIC window disappears if no operation is
made for about 10 seconds.
CH
OIC
E
CH
-
CLEAR
• The 3D PHONIC function works correctly only when
playing back a DVD VIDEO disc recorded with the Dolby
Digital. With other sources, you cannot get any effect if
you press the 3D PHONIC button.
• The 3D PHONIC function does not affect the Dolby
Digital bitstream signal from the DIGITAL OUT jacks.
• When you set the 3D PHONIC function is active, the
“ANALOG OUT” and “D. RANGE COMPRESSION”
settings in the “AUDIO” preference display are disabled.
SELECT
N
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
ANGLE
3D
PHONIC
AUDIO-fs/Rate
ZOOM
AMP VOL
RM-SXV011J
REMOTE CONTROL
¶ During playback
1 Press and hold down AUDIO-fs/Rate for a few
seconds.
The sampling frequency and bit rate of the current
digital audio are shown in the display window
temporarily. When the audio is recorded using a
surround audio format, the sampling frequency
and bit rate are shown for the front speakers, then
those for the center and/or rear speakers.
Advanced
operations
• When playing back a DVD VIDEO disc recorded with the
Dolby Digital that does not contain the rear signal, you
cannot get a correct 3D PHONIC sound though you can
change the 3D PHONIC setting.
E
RE
SC
ON
NEXT
PREVIOUS
(Example)
M VCDVD
GROUP TITLE TRACK CHAP
G
BY PROGRAM
TAL
RANDOM
38
Channel
group*
1 A-B
Sampling Bit rate
frequency
* The meanings of the channel group indications
on the display window are as follows.
L•R: Front speakers
SR: Rear speakers
C:
Center speaker
SR•C: Rear and center speakers
The sampling frequencies indicated are as follows:
44.1, 48, 88.2, 96, 176.4, and 192 (kHz). Note that any
figure below the first decimal place is omitted in
the display window.
NOTE
• With some discs, “NO INFO.” may appear instead of the
sampling frequency and bit rate.
Downloaded From DvDPlayer-Manual.com JVC Manuals
41
Advanced operations
Basic operation procedure
Menu bar functions
This section describes the functions you can perform via
the menu bar.
The available menu bar functions differ depending on
the disc type.
TV
TV
TV1
TV2
TV8
TV9
7
8
9
TV-/--
TV0
10
T
RETURN
2
3
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
T
ENTER
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL+
ENTER
CH
OIC
E
2/3
EN
RE
SC
ON
NEXT
CH
-
SELECT
STROBE
SLOW+
SLOW-
VOL+
ENTER
CH
OIC
E
TV/VIDEO
CANCEL
NU CH
ME
+
OP
CLEAR
ME
NU
VOL-
+10
TITLE/
GROUP
PREVIOUS
+10
TITLE/
GROUP
0
PAGE
VOL-
MUTING
0
PAGE
TV3
1
10
TV7
DVD
TV4
RETURN
To bring up the menu bar
DVD
STANDBY/ON
OPEN/
CLOSE
REPEAT SUB TITLE AUDIO
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
ON SCREEN
N
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
3D
PHONIC
ANGLE
ZOOM
AMP VOL
STROBE
SLOW+
SLOW-
RM-SXV011J
REPEAT SUB TITLE AUDIO
VFP
REMOTE CONTROL
fs/Rate PROGRESSIVE
SCAN
DIGEST
ANGLE
3D
PHONIC
ZOOM
AMP VOL
1 Use 2/3 to select the icon you want to work
¶ When a disc is inserted
with.
1 Press ON SCREEN.
The selected icon is pointed by
Advanced
operations
The status bar, according to the disc type, appears
on the TV screen.
See page 24 about the status bar.
(Example of the status bar for DVD VIDEO)
TITLE 33 CHAP 33
8.5Mbps
TOTAL 1:25:58
2 Press ON SCREEN again.
The appropriate menu bar, according to the disc
type, appears together with the status bar. The
menu bar includes some icons which indicate the
associated functions.
GROUP 3 TRACK 33
8.5Mbps
OFF
TRACK
TOTAL 1:25:58
1/3
PROG. RND.
PAGE 32/32
(for DVD VIDEO)
TITLE 33 CHAP 33
8.5Mbps
OFF
CHAP.
1/3
TOTAL 1:25:58
1/5
1/3
(for SVCD)
TRACK 33
OFF
PROG.
RND.
PROG.
RND.
PROG.
RND.
ST1
TIME
25:58
-/4
(for Video CD)
TRACK 33
OFF
TIME
25:58
TIME
25:58
ST
(for Audio CD)
TRACK 33
OFF
NOTE
• To dismiss the menu bar (and status bar):
Press ON SCREEN.
42
2 Press ENTER.
With many icons, an appropriate pull-down
window appears, however, there are some
exceptions.
• See the following pages for details about each
function.
• Note that some functions are not available during
playback. (You cannot move
Downloaded From DvDPlayer-Manual.com JVC Manuals
to the associated
icon when it is not available.)
NOTES
• When
(for DVD AUDIO)
.
appears on the TV screen:
You cannot use the selected function because of disc
contents.
• A mark or text on the menu icon for the function or
mode currently selected is shown in blue.
Advanced operations
English
Menu bar functions for DVD AUDIO
OFF
2
1
TRACK
3
PROG. RND.
4
5
6
TOTAL 1:25:58
1/3
PAGE 32/32
7
8
Selected Icon
1
Time mode selection
(During playback only)
Selects the time mode shown in
the display window on the front
panel and in the status bar.
2
Repeat mode
(During playback only)
Select the repeat mode.
Menu icons
The following table shows the menu bar
functions available for DVD AUDIO.
Note that, in the description of the
operation column, we assume the
associated icon is selected.
Operation
Press ENTER to select the time mode among the
following.
TIME
REM
TOTAL
T.REM
Return to initial
• TIME:
Current track elapsed time
• REM:
Current track remaining time
• TOTAL:
Current group elapsed time
• T.REM:
Current group remaining time
1 Press ENTER to open the pull-down window.
2 Use 5/∞ to select the repeat mode among the
followings.
TRACK j GROUP j A-B j OFF
• TRACK: Current title repeat
• GROUP:
Current group repeat
• A-B:
Repeats a desired part (A-B repeat)
Note
• If the disc has only one group and
one track, “TOTAL” and “TIME” show
the same value.
• If you select “OFF” during repeat
playback, the unit continues playback
without repeating.
• For the subsequent operations for the
A-B repeat, see page 34.
Advanced
operations
GROUP 3 TRACK 33
8.5Mbps
3 Press ENTER to make the selected repeat
function active.
(See pages 33 to 35 for details about repeat function.)
1 Press ENTER to open the pull-down window.
2 Use numeric buttons to enter a desired time.
Time search
3 Press ENTER to play back from the specified
Specifies the elapsed time from the
time.
beginning of the current group,
3
from which the unit starts
playback.
4
TRACK
Track search
(During playback only)
Specifies a desired track to be
played back from.
(See page 28 for details about time search function.)
1 Press ENTER to open the pull-down window.
2 Use numeric buttons to enter a desired track
number.
• For example of entering “12”, press “1” then “2”.
3 Press ENTER to play back from the specified
track.
• The “10” and “+10” buttons are not
used in this function.
• You can also locate a desired track
directly by specifying the track
number using the numeric buttons
during playback. See page 23.
• When the track number is incorrect:
Overwrite the incorrect number with the correct
number.
5
PROG.
Program
(While stopped only)
Specifies the playback order of
tracks.
6
RND.
Random
(While stopped only)
1 Press ENTER to bring up the program table.
2 Specify tracks in the desired order using the
numeric buttons.
3 Press 3 to start program playback.
(See page 31 for details about program playback.)
1 Press ENTER to activate random playback.
(See page 33 for details about random playback.)
Activates random playback.
Downloaded From DvDPlayer-Manual.com JVC Manuals
43
Advanced operations
Selected Icon
Operation
Note
1 Press ENTER to open the pull-down window.
2 Use 5/∞ to select a desired audio language or
sound.
Example:
7
Audio selection
(During playback only)
Selects the audio language or
sound.
1/3 ENGLISH j 2/3 FRENCH j 3/3 SPANISH
3 Press ENTER to play back with the selected
audio.
(See page 36 for details about audio selection.)
8
1 Press ENTER to open the pull-down window.
2 Use 5/∞ to select a desired page number.
3 Press ENTER to play back with the selected page.
PAGE
Page selection
(During playback only)
(See page 30 for details about page selection.)
Selects the page.
Menu bar functions for DVD VIDEO
TITLE 33 CHAP 33
8.5Mbps
OFF
1
2
CHAP.
3
4
1/3
5
TOTAL 1:25:58
1/5
6
1/3
7
Advanced
operations
Selected Icon
1
Time mode selection
(During playback only)
Selects the time mode shown in
the display window on the front
panel and in the status bar.
2
Repeat mode
(During playback only)
Select the repeat mode.
Menu icons
The following table shows the menu bar
functions available for DVD VIDEO.
Note that, in the description of the
operation column, we assume the
associated icon is selected.
Operation
Press ENTER to select the time mode among the
followings.
TOTAL
T.REM
TIME
REM
Return to initial
• TOTAL:
Current title elapsed time
• T.REM:
Current title remaining time
• TIME:
Current chapter elapsed time
• REM:
Current chapter remaining time
1 Press ENTER to open the pull-down window.
2 Use 5/∞ to select the repeat mode among the
following.
CHAPTER j TITLE j A-B j OFF
• CHAPTER:Current chapter repeat
• TITLE:
Current title repeat
• A-B:
Repeats a desired part (A-B repeat)
Note
• If the disc has only one title and one
chapter, “TOTAL” and “TIME” show
the same value.
• If you select “OFF” during repeat
playback, the unit continues playback
without repeating.
• For the subsequent operations for the
A-B repeat, see page 34.
3 Press ENTER to make the selected repeat
function active.
(See pages 33 to 35 for details about repeat function.)
1 Press ENTER to open the pull-down window.
2 Use numeric buttons to enter a desired time.
3 Press ENTER to play back from the specified
Specifies the elapsed time from the
time.
beginning of the current title, from
3
Time search
which the unit starts playback.
4
CHAP.
Chapter search
(During playback only)
Specifies a desired chapter to be
played back from.
(See page 28 for details about time search function.)
1 Press ENTER to open the pull-down window.
2 Use numeric buttons to enter a desired chapter
number.
• For example of entering “12”, press “1” then “2”.
3 Press ENTER to play back from the specified
chapter.
• When the chapter number is incorrect:
Overwrite the incorrect number with the correct
number.
44
Downloaded From DvDPlayer-Manual.com JVC Manuals
• The “10” and “+10” buttons are not
used in this function.
• You can also locate a desired chapter
directly by specifying the chapter
number using the numeric buttons
during playback. See page 23.
Advanced operations
Selected Icon
5
Audio selection
(During playback only)
Selects the audio language or
sound.
Operation
Note
1 Press ENTER to open the pull-down window.
2 Use 5/∞ to select a desired audio language or
sound.
Example:
• For DVD VIDEO, the selected
language may be abbreviated on
the TV screen. See “Table of
languages and their abbreviations”
on page 58.
1/3 ENGLISH j 2/3 FRENCH j 3/3 SPANISH
English
3 Press ENTER to play back with the selected
audio.
(See page 36 for details about audio selection.)
1 Press ENTER to open the pull-down window.
2 Use 5/∞ to select a desired subtitle language.
Example:
6
Subtitle selection
(During playback only)
1/3 ENGLISH j 2/3 FRENCH j 3/3 SPANISH j
-/3 OFF
Selects the subtitle language.
3 Press ENTER to play back with the selected
subtitle.
(See page 35 for details about subtitle selection.)
1 Press ENTER to open the pull-down window.
2 Use 5/∞ to select a scene angle.
Example:
7
Angle selection
(during playback only)
1/3 j 2/3 j 3/3
Selects a desired scene angle in
the multi-angle part.
3 Press ENTER to play back with the selected
scene angle.
(See page 37 for details about angle selection.)
TRACK 33
OFF
1
2
3
PROG.
RND.
4
5
TIME
ST1
1
2
3
PROG.
RND.
4
5
1
2
3
PROG.
RND.
4
5
TIME
25:58
ST
Menu icons
6
TRACK 33
OFF
Menu icons
7
TRACK 33
OFF
25:58
-/4
6
TIME
Time mode selection
Selects the time mode shown in
the display window on the front
panel and in the status bar.
2
Repeat mode
Select the repeat mode.
The following table shows the menu bar
functions available for SVCD/Video CD/
Audio CD.
Note that, in the description of the
operation column, we assume the
associated icon is selected.
25:58
Menu icons
Selected Icon
1
Advanced
operations
Menu bar functions for SVCD/Video CD/Audio CD
Operation
Note
• When you select “REM” while
stopped, you can change the track
by pressing 4 or ¢.
TIME
REM
TOTAL
T.REM
Return to initial
• TIME:
Current track elapsed time
• During stopped, “REM” shows the
recording time of the current track,
• REM:
Current track remaining time
while “T.REM” shows the total time
• TOTAL:
Disc elapsed time
of the disc.
• T.REM:
Disc remaining time
Press ENTER to select the time mode among the
followings.
1 Press ENTER to open the pull-down window.
2 Use 5/∞ to select the repeat mode among the
followings.
OFF j TRACK j ALL j A-B j OFF
• TRACK: Current track repeat
• ALL:
All track repeat
• A-B:
Repeats a desired part (A-B repeat)
• If you select “OFF” during repeat
playback, the unit continues
playback without repeating.
• For the subsequent operations for
the A-B repeat, see page 34.
3 Press ENTER to make the selected repeat
function active.
(See pages 33 to 35 for details about the Repeat
function.)
Downloaded From DvDPlayer-Manual.com JVC Manuals
45
Advanced operations
Selected Icon
3
Time search
(Except during SVCD/Video CD
playback with PBC)
Specifies the elapsed time from
the beginning of the disc, from
which the unit starts playback.
4
PROG.
Program
(While stopped only)
Specifies the playback order of
tracks.
5
RND.
Random
(While stopped only)
Operation
1 Press ENTER to open the pull-down window.
2 Use numeric buttons to enter a desired time.
3 Press ENTER to play back from the specified
time.
(See page 28 for details.)
1 Press ENTER to bring up the program table.
2 Specify tracks in the desired order using the
numeric buttons.
3 Press 3 to start program playback.
(See page 31 for details.)
1 Press ENTER to activate random playback.
(See page 33 for details.)
Activates random playback.
6
Audio selection
(During SVCD/Video CD playback
only)
Advanced
operations
Selects the audio channel(s).
46
7
Subtitle selection
(During SVCD playback only)
Selects the subtitle.
1 Press ENTER to open the pull-down window.
2 Use 5/∞ to select a desired audio channel(s).
3 Press ENTER to play back with the selected
audio channel(s).
(See page 36 for details about audio selection.)
1 Press ENTER to open the pull-down window.
2 Use 5/∞ to select a desired subtitle.
3 Press ENTER to play back with the selected
subtitle.
(See page 35 for details about subtitle selection.)
Downloaded From DvDPlayer-Manual.com JVC Manuals
Note
• This function cannot be used during
program playback.
MP3 disc playback
The unit can play back MP3 files on a private CD-R/RW
disc or commercial CD. We refer to a disc that contains
MP3 file as an “MP3 disc” in this manual.
Though available functions with MP3 discs are limited,
operations for the available functions are similar to those
with Audio CD discs.
Note that, if a disc contains both of MP3 and JPEG files,
you can only play back files of either type selected by the
MP3/JPEG setting in the PICTURE preference display
(see page 60).
“MP3” stands for “MPEG Audio Layer-3,” and is the
part of the MPEG standard. It can store high quality
stereo audio using very little space by only saving the
audible sounds and discarding the sounds your ears
won’t pick up. A CD can store up to around 10 hours of
MP3 audio, which is 10 times as much as Audio CD.
NOTE
English
• Some tracks on an MP3 disc are skipped and may not
be played back normally because of the disc
configuration or characteristics determined by the
writing (encoding) software and hardware used for
recording. Such symptoms may occur regardless of
whether using a disc you recorded or using a
commercially available disc.
English
Make sure that the TV - DVD switch on
the remote control unit is set to “DVD”
when using the 5/∞/2/3 and numeric
buttons for controlling the unit.
About MP3 disc
• The unit does not support the ID3 tag.
• If the disc is recorded with multiple sessions, the unit
supports up to five sessions.
• You cannot play back Tracks in the desired
(programmed) or random order.
• The unit only can play back Tracks with any of the
following file extensions; “.MP3”, “.Mp3”, “.mp3” and
“.mP3”.
• Time required for reading the disc contents differs with
discs, depending on the numbers of Groups (folders)
and Tracks (files) recorded, etc.
• While an MP3 disc is loaded, you cannot bring up any
preference display (see pages 56 and 57).
Operations
Basic operations
Available :
TV-/--
TV0
MUTING
10
0
+10
RETURN
Group 1
Track 1
Group 1'
Group 2
up to 99 Groups
per disc
up to 150 Tracks per Group
NOTES for making a private MP3 disc
using a CD-R/CD-RW disc:
• Select “ISO 9660” as the disc format.
• Finalize the disc after completing recording.
• We recommend to record a material at 44.1-kHz Fs and
at the 128-kbps data transfer rate.
Downloaded From DvDPlayer-Manual.com JVC Manuals
TITLE/
GROUP
TV/VIDEO
CANCEL
ME
NU
VOL-
VOL+
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
• Each file is regarded as a Track.
• A folder which has one or more files (Tracks) is
regarded as a Group.
• A folders’ folder which does not manage any file
directly is ignored.
• Files which do not belong to any folder are grouped
into “Group 1.”
• The unit recognizes up to 150 Tracks per Group, and up
to 99 Groups per disc. It ignores those exceeding the
maximum numbers and cannot play back them. If
there is any type of files other than MP3 files in a
folder. Those files are also counted down from the
total number of 150.
PAGE
NU CH
ME
+
OP
SELECT
N
Basic control
buttons
MP3 disc
playback
On an MP3 disc, each material (song) is recorded on a
file. Files are sometimes grouped into a folder by artist,
album, category, etc. In addition, a folder can be a
member of another folder, creating hierarchical folder
layers. If you are familiar with a personal computer, you
may easily understand the hierarchical file/folder
construction of MP3 discs.
This unit simplifies the hierarchical construction of a disc
and manages files and folders by “Tracks” and “Groups”
in the following manners.
T
DVD
• Some discs may not be played back because of the disc
characteristics or recording condition.
• The unit does not support “packet writing” discs.
What is MP3?
TV
English
NOTES
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
3D
PHONIC
ANGLE
ZOOM
AMP VOL
The following table shows basic functions of basic
control buttons.
Buttons
ENTER
3
7
8
4/¢
Functions
Starts playback while stopped.
Starts playback while stopped or
paused.
Stops playback.
Pauses playback.
Skips back or forward a Track in the
Group* during playback.
Selects the previous or next Track in the
Group* while stopped.
*You can skip a Track across a Group.
• If you press 3 during playback, or press 7 to stop
playback followed by 3, the unit starts playback from
the beginning of the current track.
• The 2/3 buttons work the same as the 4/¢
buttons.
47
MP3 disc playback
2 Use 5/∞ to move the bar to a desired Group.
NOTES
• The current Group and Track numbers are shown on the
display window in the following manner.
LPCM VCDVD
GROUP TITLE TRACK CHAP
MPEG 3 8
DOLBY PROGRAM
DIGITAL
RANDOM
DTS
Current Group
number
1 A-B
On the right column, Tracks in the selected Group
are shown.
When selecting a Group, Track 1 is initially selected
(highlighted).
3 Use 4/¢ to select a desired Track, then
Current Track
number
Current track
elapsed time
• You cannot advance or reverse playback of an MP3 disc
rapidly.
• You cannot see any other time information but the
current track elapsed time.
Selecting the desired Group
and Track
press ENTER or 3.
or
Use the numeric buttons to directly specify a
desired Track number.
• To select a number between 1 and 10:
Press the corresponding button for the number.
• To select a number higher than 10:
Use the +10 button.
Examples:
To select 13: +10 → 3
To select 34: +10 → +10 → +10 → 4
To select 40: +10 → +10 → +10 → 10
Available :
When loading an MP3 disc, after the disc contents are
read, the MP3 CONTROL display automatically appears
on the TV screen.
The unit starts playback from the selected Track.
In the MP3 CONTROL display and the display window
on the front panel, you can see the current Group and
Track numbers, as well as Track elapsed time.
MP3 disc
playback
MP3 CONTROL
Group : 01 / 10
Track : 01 / 06 (Total 28)
spring
sumer
fall
winter
sea
mountain
camp
picnic
skiing
flower
begonia.mp3
german chamomile.mp3
kiwi fruit.mp3
orchard grass.mp3
petunia.mp3
north pole.mp3
Current Track elapsed time
MP3 CONTROL
Time : 00:03:08
Group : 01 / 10
Track : 01 / 06 (Total 28)
spring
sumer
fall
winter
sea
mountain
camp
picnic
skiing
flower
begonia.mp3
german chamomile.mp3
kiwi fruit.mp3
orchard grass.mp3
petunia.mp3
north pole.mp3
You can specify the desired Group/Track from the display
by the following procedure.
TV
TV
TV1
TV2
2
3
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV0
10
MUTING
0
PAGE
TV/VIDEO
CANCEL
ME
NU
VOL-
VOL+
ENTER
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
4/¢
CLEAR
SELECT
ENTER
N
SLOW+
REPEAT SUB TITLE AUDIO
NOTES
3
VFP
fs/Rate PROGRESSIVE
SCAN
ANGLE
3D
PHONIC
• You can also select a desired Track by pressing 3 to move
the black bar to the right (Track) column then using 5/∞.
STROBE
SLOW-
DIGEST
Selected
Track
Numeric
buttons
+10
TITLE/
GROUP
NU CH
ME
+
OP
CH
OIC
E
Track column of the
current Group
TV3
1
TV-/--
T
DVD
TV4
RETURN
5/∞/2/3
Group
column
DVD
STANDBY/ON
OPEN/
CLOSE
ZOOM
AMP VOL
• Up to 32 characters are displayed as a group or track
name on the MP3 CONTROL display.
• If an MP3 file name includes any 2-byte character, the
unit may not show the file name correctly.
• Only MP3 files are shown on the MP3 CONTROL display.
RM-SXV011J
REMOTE CONTROL
¶ When the MP3 CONTROL display is shown.
1 Make sure that the black (cursor) bar is in the
left (Group) column.
If it is in the right column, press 2 to move it to the
left column.
48
Downloaded From DvDPlayer-Manual.com JVC Manuals
• The order of Groups/Tracks shown in the MP3
CONTROL display may differ from the order shown on
your personal computer when you set the disc on your
computer.
MP3 disc playback
Direct selection
English
Repeat playback
English
Available :
Available :
You can select a desired Group directly by specifying the
Group number.
TV-/--
TV0
10
DVD
TV
T
STANDBY/ON
OPEN/
CLOSE
DVD
MUTING
0
PAGE
RETURN
TV
English
You can repeat playback of the current Track, current
Group or all MP3 files on the disc.
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
TV1
TV2
TV3
1
2
3
TV4
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
TV-/--
T
9
TV0
10
MUTING
0
PAGE
RETURN
CH
OIC
E
Numeric
buttons
CLEAR
TV/VIDEO
CANCEL
SELECT
N
STROBE
REPEAT SUB TITLE AUDIO
REPEAT
VOL+
CH
-
E
RE
SC
ON
NEXT
SELECT
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
ENTER
PREVIOUS
SLOW+
SLOW-
TITLE/GROUP
ME
NU
VOL-
CLEAR
E
RE
SC
ON
NEXT
+10
TITLE/
GROUP
NU CH
ME
+
OP
CH
OIC
E
CH
-
PREVIOUS
ANGLE
3D
PHONIC
N
ZOOM
AMP VOL
STROBE
RM-SXV011J
REMOTE CONTROL
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
VFP
¶ During playback or while stopped
fs/Rate PROGRESSIVE
SCAN
DIGEST
3D
PHONIC
ANGLE
ZOOM
AMP VOL
1 Press REPEAT.
RM-SXV011J
¶ During playback or while stopped
1 Press TITLE/GROUP.
“--” is shown in the Group display area of the
display window.
(Example for the indication of window)
LPCM VCDVD
GROUP TITLE TRACK CHAP
MPEG
DOLBY PROGRAM
DIGITAL
RANDOM
DTS
38
1 A-B
Group
Current track
display area number
2 Use the numeric buttons to specify a desired
Group number.
• To select a number between 1 and 10:
Press the corresponding button for the number.
• To select a number higher than 10:
Use the +10 button.
Examples:
To select 13: +10 → 3
To select 34: +10 → +10 → +10 → 4
To select 40: +10 → +10 → +10 → 10
Specify the Group number within several seconds
after pressing TITLE/GROUP (i.e. while the display
window shows “--” for the Group number, instead
of the current Group number).
The unit starts playback from Track 1 of the selected
Group.
3 Use the numeric buttons to specify a desired
Track number.
The unit starts playback from the specified Track.
You can also use 4/¢ or 5/∞ for specifying a
track, instead of the numeric buttons.
Downloaded From DvDPlayer-Manual.com JVC Manuals
Each time you press REPEAT, the repeat mode
changes as follows. You can see the current mode
via the display window as well as the MP3
CONTROL display.
If you press REPEAT while stopped, you need to
press ENTER or 3 to start repeat playback.
MP3 CONTROL
display
Display
Window
Function
REPEAT TRACK
Repeats the current
Track.
REPEAT GROUP
Repeats all Tracks in
the current Group.
REPEAT ALL
Repeats all Tracks on
the disc.
No indication
The repeat mode is off.
(TV screen)
MP3 CONTROL
MP3 disc
playback
REMOTE CONTROL
Selected repeat mode
REPEAT TRACK
Group : 01 / 10
Track : 01 / 06 (Total 28)
spring
sumer
fall
winter
sea
mountain
camp
picnic
skiing
flower
begonia.mp3
german chamomile.mp3
kiwi fruit.mp3
orchard grass.mp3
petunia.mp3
north pole.mp3
(Display window)
LPCM VCDVD
GROUP TITLE TRACK CHAP
MPEG
DOLBY PROGRAM
DIGITAL
RANDOM
DTS
38
1 A-B
Repeat mode indicator
• To stop repeat playback
Press 7. Note that the repeat mode remains.
• To quit repeat playback
During playback, press REPEAT as many times until
no repeat icon is shown on the display window.
While stopped, press REPEAT as many times until
repeat mode indication on the MP3 CONTROL display
goes off.
49
MP3 disc playback
Checking the sampling frequency and
bit rate
Available :
You can check the sampling frequency and bit rate of
digital audio during playback.
TV
TV
TV1
DVD
TV2
TV3
1
2
3
TV4
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
PAGE
RETURN
T
DVD
STANDBY/ON
OPEN/
CLOSE
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
N
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
ANGLE
3D
PHONIC
AUDIO-fs/Rate
ZOOM
AMP VOL
RM-SXV011J
REMOTE CONTROL
¶ During playback
1 Press and hold down AUDIO-fs/Rate for a few
seconds.
MP3 disc
playback
The sampling frequency and bit rate of the current
digital audio are shown in the display window
temporarily.
(Example)
CM VCDVD
GROUP TITLE TRACK CHAP
EG
LBY PROGRAM
GITAL
RANDOM
S
38
Channel
group*
1 A-B
Sampling
frequency
Bit rate
* The meaning of the channel group indication on
the display window is as follows.
L•R: Front speakers
Note that any figure below the first decimal place is
omitted in the display window.
NOTE
• With some discs, “NO INFO.” may appear instead of the
sampling frequency and bit rate.
50
Downloaded From DvDPlayer-Manual.com JVC Manuals
JPEG disc playback
The unit can play back JPEG files on a private CD-R/RW
disc. We refer to a disc that contains JPEG files as a
“JPEG disc” in this manual.
Note that, if a disc contains both of MP3 and JPEG files,
you can only play back files of either type selected by the
MP3/JPEG setting in the PICTURE preference display
(See page 60).
What is JPEG?
“JPEG” is an abbreviation for the Joint Photographic
Experts Group and is an image format that utilizes a
compression technique.
There are three sub-types of the JPEG format as
follows.
• baseline JPEG: used for digital cameras, web, etc.
• progressive JPEG: used for web
• lossless JPEG: an old type and rarely used now
The unit supports only the baseline JPEG type,
therefore, it cannot display pictures of the other types
(progressive and lossless). If a JPEG disc contains
JPEG files of non-baseline type, the unit recognizes
those files as JPEG files, the JPEG CONTROL display
and the display window shows the information of the
contents (file name, file number, etc.), but you cannot
show the still pictures of those files (the TV screen
appears only in black and “NON PLAYABLE FILE” is
shown in the display window).
NOTE
TV
DVD
Make sure that the TV - DVD switch on
the remote control unit is set to “DVD”
when using the 5/∞/2/3, numeric
buttons for controlling the unit.
NOTES for making a private JPEG disc
using a CD-R/CD-RW disc:
English
English
• Select “ISO 9660” as the disc format.
• Finalize the disc after completing recording.
English
• We recommend to record a material at “640 x 480”
resolution.
• The unit supports only the baseline JPEG type,
therefore, it cannot display pictures of the other types
(progressive and lossless). If a JPEG disc contains JPEG
files of non-baseline type, the unit recognizes those
files as JPEG files. the JPEG CONTROL display and the
display window shows the information of the contents
(file name, file number, etc.), but you cannot show the
still pictures of those files (the TV screen appears only
in black).
NOTES
• The unit does not support “packet writing” discs.
• If the disc is recorded with multiple sessions, the unit
supports up to five sessions.
• Some disc may not be played back, or take some time to
open the whole picture because of the disc characteristics
or recording condition.
• You cannot play back files in the desired (programmed)
or random order.
• The screen saver function is activated while same
picture is displayed for more than 5 minutes except
during slide show playback (see page 53).
• The unit only can play back files with any of the
following file extensions; “.jpg”, “.jpeg”, “.JPG”, “.JPEG”
and any uppercase and lowercase combination (such as
“.Jpg”).
About JPEG disc
• When a picture resolution is more than “640 x 480”, it
takes some time to open the whole picture.
On a JPEG disc, each material (still picture) is recorded on a
file. Files may be grouped into a folder by category, etc. In
addition, a folder can be a member of another folder,
creating hierarchical folder layers. If you are familiar with a
personal computer, you may easily understand the
hierarchical file/folder construction of JPEG discs.
This unit simplifies the hierarchical construction of a disc
and manages folders by “Groups” in the following
manners.
• Carry out an operation after opening the whole
picture.The unit does not accept any operation
(Stopping the unit, zooming in/out a picture etc.) while
opening the picture.
• A folder which has one or more files is regarded as a
Group.
• A folders’ folder which does not manage any file
directly is ignored.
• Files which do not belong to any folder are grouped
into “Group 1.”
• The unit recognizes up to 150 files per Group, and up
to 99 Groups per disc. It ignores those exceeding the
maximum numbers and cannot play back them. If
there is any type of files other than JPEG files in a
folder. Those files are also counted down from the
total number of 150.
Group 1
file 1
Group 1'
• Time required for reading the disc contents differs with
discs, depending on the numbers of Groups (folders)
and files recorded, etc.
JPEG disc
playback
• If a JPEG file name includes any 2-byte character, the
unit may not show the file name correctly.
• If you play back a non-baseline JPEG file:
The unit cannot display the still picture of the file. (the
TV screen appears only in black.) In this case, other
operations (such as stopping playback, selecting a file,
etc.) are possible but may take a long time.
• While a JPEG disc is loaded, you cannot bring up any
preference display (see pages 56 and 57).
• The available horizontal resolution of a JPEG file is up to
2,400 lines.
Group 2
up to 99 Groups
per disc
up to 150 files per directory
Downloaded From DvDPlayer-Manual.com JVC Manuals
51
JPEG disc playback
3 Use 4/¢ to select a desired file.
4 Press ENTER.
Basic operations
The selected file (still picture) is shown on the TV.
In the display window, you can see the current
Group and file numbers.
To see a desired picture
Available : JPEG
When loading a JPEG disc, after the disc contents are
read, the JPEG CONTROL display automatically appears
on the TV screen.
JPEG CONTROL
Group : 01 / 10
File : 01 / 06 (Total 28)
spring
sumer
fall
winter
sea
mountain
camp
picnic
skiing
flower
begonia.jpg
german chamomile.jpg
kiwi fruit.jpg
orchard grass.jpg
petunia.jpg
north pole.jpg
JPEG CONTROL
Group : 01 / 10
File : 01 / 06 (Total 28)
spring
sumer
fall
winter
sea
mountain
camp
picnic
skiing
flower
begonia.jpg
german chamomile.jpg
kiwi fruit.jpg
orchard grass.jpg
petunia.jpg
north pole.jpg
Group
column
You can select a desired file for playback via this display.
File column of the
current Group
Selected
file
• You can also select a desired file by pressing 3 to move the
black bar to the right (file) column then using 5/∞.
• To return the black bar to the Group column, press 2.
TV
TV
TV1
DVD
TV2
2
3
TV5
TV6
4
5
TV7
TV8
6
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
PAGE
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
• To play back another picture:
Use 4/¢ or 5/∞ to select the desired picture.
You can select a picture in another Group.
TV3
1
TV4
RETURN
T
DVD
STANDBY/ON
OPEN/
CLOSE
SELECT
5/∞/2/3
N
STROBE
4/¢
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
ANGLE
3D
PHONIC
JPEG disc
playback
• To dismiss the picture:
Press 7 or MENU.
The TV screen returns to the JPEG CONTROL
display.
ZOOM
AMP VOL
RM-SXV011J
REMOTE CONTROL
¶ When the JPEG CONTROL display is shown
1 Make sure that the black (cursor) bar is in the
left (Group) column.
If it is in the right column, press 2 to move it to the
left column.
2 Use 5/∞ to move the bar to a desired Group.
On the right column, files in the selected Group are
shown.
When selecting a Group, file 1 is initially selected
(highlighted).
52 From DvDPlayer-Manual.com JVC Manuals
Downloaded
NOTES
• Up to 32 characters are displayed as a group or file
name on the JPEG CONTROL display.
• The current Group and file number are also shown on
the display window in the following manner.
LPCM VCDVD
GROUP TITLE TRACK CHAP
MPEG 3 8
DOLBY PROGRAM
DIGITAL
RANDOM
DTS
Current Group
number
1 A-B
Current file
number
• Only JPEG files are shown on the display window.
JPEG disc playback
To zoom in/out the picture [ZOOM]
Available :
T
RETURN
OP
PAGE
TITLE/
GROUP
NU CH
ME
+
ME
NU
VOL+
ENTER
CLEAR
CH
-
ON
NEXT
SELECT
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
ANGLE
3D
PHONIC
English
You can see files (still pictures) one after another
automatically in the slide show mode.
In this mode, each file (still picture) is shown on the TV
for approximately 3 seconds and then automatically
changed to the next file one after another.
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
5/∞/2/3
EN
RE
SC
PREVIOUS
English
TV/VIDEO
CANCEL
VOL-
CH
OIC
E
JPEG
To see pictures continuously
[slide show mode]
English
ZOOM
ZOOM +/–
AMP VOL
¶ During JPEG picture is shown on the TV screen
To play back pictures from the
beginning of the disc
1 Press ZOOM + or −.
Available :
The unit zooms in by pressing ZOOM + or zooms
out by pressing ZOOM −.
Each time you press ZOOM +, the magnification is
doubled (up to x 1024).
Each time you press ZOOM −, the magnification is
halved (down to x 1/8).
TV
DVD
STANDBY/ON
OPEN/
CLOSE
TV
TV1
DVD
TV2
TV3
1
2
3
TV4
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
PAGE
RETURN
T
JPEG
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
N
3
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
ANGLE
3D
PHONIC
ZOOM
AMP VOL
RM-SXV011J
REMOTE CONTROL
ZOOM x 4
¶ After inserting a JPEG disc
1 Press 3.
At the top-left of the screen, the information for the
current magnification appears. While zoomed in,
the indication for the zoomed-in position, which
can be moved by operating the next step, appears
together.
2 Use 5/∞/2/3 to move the zoomed position.
JPEG disc
playback
The slide show starts from the beginning of the
disc.
NOTES
• To stop slide show playback (to dismiss the picture) in
the middle of the slide show playback:
Press 7 or MENU.
The TV screen returns to the JPEG CONTROL display.
Pressing 3 resumes slide show playback from the last
picture you opened.
• To keep showing a current picture during the slide show
ZOOM x 4
Press 8 or ENTER.
The picture does not change to the next picture.
Pressing 3 resumes the slide show playback from the
next picture.
• If a black screen appears continuously in the slide show
playback:
NOTES
• Even in the slide show mode, you can zoom in or out a
picture while paused (see the next column).
• To return to normal screen:
The file currently played may be non-baseline JPEG file.
In this case, select a playable file (a baseline JPEG file)
again (e.g., pressing 7 or MENU to open the JPEG
CONTROL display, etc.)
Note that it may take a long time to select another file.
Press ENTER.
• While zoomed, the picture may look coarse.
• The zoom information on the screen will disappear if
you do not operate the zoom function for five seconds.
• The zoom information appears again when you press
ZOOM +/−, or 5/∞/2/3.
Downloaded From DvDPlayer-Manual.com JVC Manuals
53
JPEG disc playback
Direct selection
Selecting the start point of the slide
show
Available :
TV
JPEG
“--” is shown in the Group display area of the
display window.
(Example for the indication of display window)
DVD
TV
TV1
DVD
TV2
TV3
1
2
3
TV4
TV5
TV6
4
5
TV7
TV8
6
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
+10
PAGE
RETURN
T
1 Press TITLE/GROUP.
STANDBY/ON
OPEN/
CLOSE
5/∞
¶ During playback or while stopped
TITLE/
GROUP
Numeric
buttons
LPCM VCDVD
GROUP TITLE TRACK CHAP
MPEG
DOLBY PROGRAM
DIGITAL
RANDOM
DTS
38
TV/VIDEO
CANCEL
NU CH
ME
+
OP
Group
display area
TITLE/GROUP
ME
NU
VOL-
VOL+
1 A-B
Current track
number
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
N
4/¢
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
3
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
ANGLE
3D
PHONIC
ZOOM
AMP VOL
RM-SXV011J
REMOTE CONTROL
From the JPEG CONTROL display
¶ During JPEG CONTROL display is shown
1 Make sure that the black (cursor) bar is in the
left (Group) column.
If it is in the right column, press 2 to move it to the
left column.
2 Use the numeric buttons to specify a desired
Group number.
• To select a number between 1 and 10:
Press the corresponding button for the number.
• To select a number higher than 10:
Use the +10 button.
Examples:
To select 13: +10 → 3
To select 34: +10 → +10 → +10 → 4
To select 40: +10 → +10 → +10 → 10
Specify the Group number within several seconds
after pressing TITLE/GROUP (i.e. while the display
window shows “--” for the Group number, instead
of the current Group number).
3 Use the numeric buttons to specify a desired
Track number.
JPEG disc
playback
JPEG CONTROL
Group : 01 / 10
File : 01 / 06 (Total 28)
spring
sumer
fall
winter
sea
mountain
camp
picnic
skiing
flower
begonia.jpg
german chamomile.jpg
kiwi fruit.jpg
orchard grass.jpg
petunia.jpg
north pole.jpg
You can specify the Track number according to the
order in the JPEG CONTROL display. You must
specify a Track number within 5 seconds after
carrying out step 2.
The unit starts slide show playback from the
specified Track. If you do not specify a Track
number, the unit starts slide show playback from
the first Track in the Group.
• You can skip a file in the slide show by using 4/¢ or
5/∞.
2 Use 5/∞ to move the bar to a desired Group.
On the right column, files in the selected Group are
shown.
When selecting a Group, file 1 is initially selected
(highlighted).
3 Use 4/¢ to select a desired file.
4 Press 3.
The slide show starts from the specified file.
• You can select a file in the current group by using the
numeric buttons.
NOTES
• To stop slide show playback (to dismiss the picture) in
the middle of the slide show playback:
Press 7 or MENU.
The TV screen returns to the JPEG CONTROL display.
Pressing 3 resumes slide show playback from the last
picture you opened.
• To keep showing a current picture during the slide show
Press 8 or ENTER.
The picture does not change to the next picture.
Pressing 3 resumes the slide show playback from the
next picture.
• If a black screen appears continuously in the slide show
playback:
The file currently played may be non-baseline JPEG file.
In this case, select a playable file (a baseline JPEG file)
again (e.g., pressing 7 or MENU to open the JPEG
CONTROL display, etc.).
Note that it may take a long time to select another file.
54 From DvDPlayer-Manual.com JVC Manuals
Downloaded
JPEG disc playback
• To stop repeat playback
Press 7. Note that the repeat mode remains.
Repeat function
English
English
Available :
JPEG
In the slide show mode, you can repeat playback of JPEG
files in a Group or on the disc.
TV
TV
TV1
TV2
TV3
1
2
3
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
PAGE
English
DVD
TV4
RETURN
T
DVD
STANDBY/ON
OPEN/
CLOSE
• To quit repeat playback
During playback, press REPEAT as many times until
no repeat icon is shown on the display window.
While stopped, press REPEAT as many times until
repeat mode indication on the JPEG CONTROL
display goes off.
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
REPEAT
N
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
ANGLE
ZOOM
3D
PHONIC
AMP VOL
RM-SXV011J
REMOTE CONTROL
¶ While the JPEG control display is shown
1 Press REPEAT.
Pressing REPEAT switches the repeat mode.
If you press REPEAT while stopped, you need to
press 3 to start repeat playback.
The mode is shown in the display window by icons,
while on the JPEG CONTROL display by mode
names, as follows.
Display
Window
Function
REPEAT ALL
All tracks on the disc are
repeated.
REPEAT GROUP
All Tracks in the current
Group are repeated.
No indication
The repeat mode is off.
JPEG disc
playback
JPEG
CONTROL
display
(TV Screen)
Selected repeat mode
JPEG CONTROL
REPEAT GROUP
Group : 01 / 10
File : 01 / 06 (Total 28)
spring
sumer
fall
winter
sea
mountain
camp
picnic
skiing
flower
begonia.jpg
german chamomile.jpg
kiwi fruit.jpg
orchard grass.jpg
petunia.jpg
north pole.jpg
(Display window)
LPCM VCDVD
GROUP TITLE TRACK CHAP
MPEG
DOLBY PROGRAM
DIGITAL
RANDOM
DTS
38
1 A-B
Repeat mode indicator
Downloaded From DvDPlayer-Manual.com JVC Manuals
55
Changing the initial settings
NOTE
TV
• OTHERS
Make sure that the TV - DVD switch on
the remote control unit is set to “DVD”
when using the 5/∞/2/3 and numeric
buttons for controlling the unit.
DVD
OTHERS
Selecting preferences
This chapter refers to the settings which are already
made when you purchase the unit. Read this section
when you want to connect this machine to a wide-vision
TV set or change the settings according to the
environment you use this machine.
RESUME
ON
ON SCREEN GUIDE
ON
AUTO STANDBY
OFF
AV COMPULINK MODE
DVD1
PARENTAL LOCK
SELECT
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
ENTER
How to set preferences
About the Preference display
TV
TV1
ENTER
TV2
TV3
1
2
3
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
+10
PAGE
TITLE/
GROUP
NU CH
ME
+
OP
TV/VIDEO
CANCEL
ME
NU
VOL-
• LANGUAGE
DVD
DVD
TV4
RETURN
T
The preference display consists of the LANGUAGE,
PICTURE, AUDIO, SPK.SETTING, and OTHERS setting
displays, each having setting items.
TV
STANDBY/ON
OPEN/
CLOSE
5/∞/2/3
VOL+
ENTER
CHOICE
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
LANGUAGE
MENU LANGUAGE
ENGLISH
AUDIO LANGUAGE
ENGLISH
SUBTITLE
OFF
ON SCREEN LANGUAGE
ENGLISH
SELECT
SELECT
STROBE
1 Press CHOICE.
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
ENTER
CLEAR
¶ While stopped
N
One of the Preference on-screen displays appears
on the TV screen.
You can see five icons at the top right of the onscreen display for the settings.
: Setting menu for language
• PICTURE
: Setting menu for pictures
PICTURE
MONITOR TYPE
4:3 LB
PROGRESSIVE MODE
AUTO
SCREEN SAVER
ON
MP3/JPEG
MP3
SELECT
ENTER
: Setting menu for sound
: Setting menu for speakers
: Setting menu for the systems, etc.
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
The appropriate display appears on the TV screen.
3 Use 5/∞ to move
• AUDIO
Changing the
initial settings
2 Use 2/3 to select the appropriate icon.
to the item you want to
edit by.
The color of the selected item changes.
AUDIO
DIGITAL AUDIO OUTPUT
STREAM/PCM
ANALOG OUT
MULTI CHANNEL
D. RANGE COMPRESSION
AUTO
4 Press ENTER.
The pull-down menu appears over the selected
item.
SELECT
ENTER
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
LANGUAGE
• SPK.SETTING
MENU LANGUAGE
ENGLISH
AUDIO LANGUAGE
ENGLISH
SUBTITLE
ENGLISH
ON SCREEN LANGUAGE
ENGLISH
ENGLISH
SPANISH
FRENCH
SPK.SETTING
MODE
5.1 CH.
SELECT
SIZE
ENTER
USE 5∞ TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
DELAY
LEVEL
Selected item
SELECT
ENTER
USE 5∞ TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
5 Use 5/∞ to select from options and press
ENTER.
The selected option is set.
• For details about each setting, see the following.
56
Downloaded From DvDPlayer-Manual.com JVC Manuals
Changing the initial settings
English
NOTES
• To dismiss a preference display:
Press CHOICE.
• While an MP3 or JPEG disc is loaded, you cannot bring
up any preference display.
• When a preference display is shown on a wide TV
screen, the upper and lower parts of the TV picture
sometimes may be cut off. In such a case, adjust the
picture size control of the TV.
LANGUAGE page
LANGUAGE
MENU LANGUAGE
ENGLISH
AUDIO LANGUAGE
ENGLISH
SUBTITLE
OFF
ON SCREEN LANGUAGE
ENGLISH
This page allows you to select languages concerning with DVD AUDIO/DVD
VIDEO disc playback, as well as the on-screen display language of the unit.
NOTES
• During playback, you can bring up any page of the preference displays, however,
only “ON SCREEN LANGUAGE” can be set on the “LANGUAGE” page.
SELECT
ENTER
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
Menu items
MENU LANGUAGE
You can select the default menu
language to be displayed if it is
contained on a DVD AUDIO/DVD
VIDEO disc.
Setting options
Notes/examples
ENGLISH j SPANISH j FRENCH
j CHINESE j GERMAN j
ITALIAN j JAPANESE j language
code from AA to ZU
• If the selected language is not
recorded, the disc’s default
language is selected.
• For details about language code, see
“Table of languages and their
abbreviations” (see page 58).
SUBTITLE
You can select the default subtitle
language to be displayed if it is
contained on a DVD AUDIO/DVD
VIDEO disc.
OFF j ENGLISH j SPANISH j
FRENCH j CHINESE j GERMAN
j ITALIAN j JAPANESE j
language code from AA to ZU
ON SCREEN LANGUAGE
You can select the on-screen
display language of the unit.
ENGLISH j SPANISH j FRENCH
English
ON SCREEN LANGUAGE
ENGLISH
Spanish
IDIOMA EN PANTALLA
ESPAÑOL
French
LANGUE D' ECRAN
FRANCAIS
• Some on-screen messages are
shown in English regardless of the
setting.
• You cannot change the on-screen
language shown on the MP3 and
JPEG CONTROL displays.
Downloaded From DvDPlayer-Manual.com JVC Manuals
Changing the
initial settings
AUDIO LANGUAGE
You can select the default audio
language to be played if it is
contained on a DVD AUDIO/DVD
VIDEO disc.
57
Changing the initial settings
Table of languages and their abbreviations
Afar
Abkhazian
Afrikaans
Ameharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
Bhutani
Greek
Esperanto
Estonian
Basque
FA
FI
FJ
FO
FY
GA
GD
GL
GN
GU
HA
HI
HR
HU
HY
IA
IE
IK
IN
IS
IW
JI
JW
KA
KK
KL
Persian
Finnish
Fiji
Faroese
Frisian
Irish
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Hebrew
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Changing the
initial settings
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DA
DZ
EL
EO
ET
EU
58
Downloaded From DvDPlayer-Manual.com JVC Manuals
KM
KN
KO
KS
KU
KY
LA
LN
LO
LT
LV
MG
MI
MK
ML
MN
MO
MR
MS
MT
MY
NA
NE
NL
NO
OC
Cambodian
Kannada
Korean (KOR)
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laothian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay (MAY)
Maltese
Burmese
Nauru
Nepali
Dutch
Norwegian
Occitan
OM
OR
PA
PL
PS
PT
QU
RM
RN
RO
RU
RW
SA
SD
SG
SH
SI
SK
SL
SM
SN
SO
SQ
SR
SS
ST
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sangho
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
SU
SV
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Wolof
Xhosa
Yoruba
Zulu
Changing the initial settings
English
PICTURE page
PICTURE
MONITOR TYPE
4:3 LB
PROGRESSIVE MODE
AUTO
SCREEN SAVER
ON
MP3/JPEG
MP3
SELECT
ENTER
This page allows you to select desired options concerning with a picture or
monitor screen.
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
Menu items
Setting options
Notes/examples
MONITOR TYPE
• 16:9 NORMAL (Wide Television
You can select the monitor type to
screen)
match your TV when you playback
Should be selected when you
DVD VIDEO discs recorded for wide
connect the unit to a wide-screen
screen televisions.
(16:9) TV whose aspect ratio is fixed
to 16:9 (the unit automatically
adjusts the screen width of the
output signal correctly when
• If you play back a “4:3” DVD VIDEO
playing back a “4:3” source).
source with the “16:9 NORMAL”
mode, the picture character slightly
• 16:9 AUTO (Wide Television screen)
changes due to the process for
Should be selected when you
converting the picture width.
connect a wide-screen (16:9) TV to
the unit.
• 4:3 PS (Pan Scanning Conversion)
Should be selected when you
connect a normal (4:3) TV to the
unit.
When playing back a DVD VIDEO
disc recorded by the wide picture
format, the picture is automatically
zoomed and the left and right sides
are chopped off.
PROGRESSIVE MODE
When the unit is in the progressive
scanning mode, you can select a
desired mode from three options.
Normally, set to “AUTO.”
• VIDEO
Suitable for playing back a video
source disc.
• FILM
Suitable for playing back a film or
progressive source disc.
• AUTO
Used to play back a disc containing
both video and film source
materials.
The unit recognizes the picture type
(film or video source) of the current
disc according to the disc
information.
Downloaded From DvDPlayer-Manual.com JVC Manuals
• With some discs recorded by the
wide picture format, the picture is
shown in the 4:3 LB mode even if
you select the 4:3 PS mode.
• When progressive scanning mode is
active, the PROGRESSIVE indicator
is lit. Note that the color of indication
changes depending on this setting,
source type and the unit’s status.
(See pages 7 and 8.)
• Some DVD VIDEO discs may not be
played back correctly with the
“AUTO” mode. If the playback
picture is unclear or noisy with a
particular DVD VIDEO disc, try to
change the mode.
Changing the
initial settings
• 4:3 LB (Letter Box Conversion)
Should be selected when you
connect a normal (4:3) TV to the
unit.
When playing back a DVD VIDEO
disc recorded by the wide picture
format, the picture is shown with
black bars at the top and bottom.
59
Changing the initial settings
Menu items
Setting options
Notes/examples
SCREEN SAVER
• ON
You can select the screen saver
The current picture gets dark.
function ON or OFF.
See page 18 for details about screen • OFF
The screen saver function is off.
saver function.
• When a disc contains either MP3 or
MP3/JPEG
• MP3
JPEG files, the unit can play back the
The unit can play back MP3 and
MP3 files can be played back if a disc
JPEG files recorded on a CD-R/CDcontains both of MP3 and JPEG files. files regardless of the setting.
RW disc, however, if a disc contains
both of MP3 and JPEG files, you can • JPEG
JPEG files can be played back if a disc
only play back files of either type
contains both of MP3 and JPEG files.
selected by this menu item.
AUDIO page
This page allows you to select desired options concerning with audio sound.
AUDIO
DIGITAL AUDIO OUTPUT
STREAM/PCM
ANALOG OUT
MULTI CHANNEL
D. RANGE COMPRESSION
AUTO
SELECT
ENTER
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
Menu items
Setting options
Notes/examples
DIGITAL AUDIO OUTPUT
• PCM ONLY
To connect the unit’s digital output to
Should be selected when you
an external device equipped with a
connect the DIGITAL OUT jacks of
digital input, this item must be set
the unit to the linear PCM digital
correctly.
input of other audio equipment.
See the table below for details
• DOLBY DIGITAL/PCM
about the relation between the
Should be selected when you
setting and output signals.
connect the digital input of a Dolby
Digital decoder or an amplifier with
a built-in Dolby Digital decoder.
When this option is selected,
playing back a disc recorded by the
DTS or MPEG Multichannel format
outputs a linear PCM digital signal.
• When playing a DVD VIDEO or
Audio CD disc with DTS, use a DTS
decoder to get correct signals from
your speakers.
• With some DVD VIDEO discs that are
not fully copy-protected, a 20 or 24
bit digital signal may be output.
Changing the
initial settings
• STREAM/PCM
Should be selected when you
connect the digital input of an
amplifier with a built-in DTS, MPEG
Multichannel or Dolby Digital
decoder, or the stand-alone unit of
such a decoder.
Digital output signal chart
Output
Playback discs
PCM ONLY
DVD with 48/44.1 kHz, 16/20/24
bit linear PCM
48/44.1 kHz,16 bit, stereo linear PCM
DVD with 192/176.4/96/88.2 kHz,
16/22/24 bit linear PCM
No output
DVD with DTS
DVD with Dolby Digital
48 kHz, 16 bit, stereo linear PCM
48 kHz, 16 bit, stereo linear PCM
Audio CD/Video CD/SVCD
Audio CD with DTS
CD-R/RW with MP3
60
DOLBY DIGITAL/PCM
Downloaded From DvDPlayer-Manual.com JVC Manuals
STREAM/PCM
DTS bitstream
Dolby Digital bitstream
44.1 kHz,16 bit, stereo linear PCM
44.1 kHz, 16 bit, stereo linear PCM
Linear PCM
DTS bitstream
Changing the initial settings
Menu items
ANALOG OUT
To play back a DVD VIDEO disc
recorded with surround
multichannel audio correctly, this
setting must be properly made
according to your audio system.
Setting options
Notes/examples
English
• 2-CH DOLBY SURROUND
• This function does not work when
the 3D PHONIC function is activated
Should be selected when you enjoy
(see page 40).
multichannel surround audio by
• “2-CH DOLBY SURROUND” and
connecting the unit’s AUDIO OUT
“2-CH STEREO” settings affect only
jacks to a surround decoder.
the output signal from the AUDIO
• 2-CH STEREO
OUT jacks when playing back a DVD
Should be selected when you enjoy
VIDEO disc recorded with surround
conventional 2-channel stereo
multichannel audio.
audio by connecting the unit’s
• Some DVD AUDIO discs prohibit the
AUDIO OUT jacks to a stereo
2-channel down-mix. For such a disc,
amplifier/receiver or television set,
you cannot get the down-mixed
or when you duplicate audio of a
signal even if you set “ANALOG
DVD VIDEO disc recorded with
OUT” to “2-DOLBY SURROUND” or
surround audio to your MD,
“2-CH STEREO.”
cassette, etc.
• MULTI CHANNEL
When you enjoy multichannel
surround audio by connecting the
unit’s 5.1-channel audio outputs to
an amplifier equipped with 5.1channel inputs.
• AUTO
Audio is played back with the
dynamic range compressed.
• ON
Audio is always played back with
the dynamic range compressed.
• This function works only when
playing back a disc recorded with
Dolby Digital. The setting is not
effective for other discs.
• This function does not work when
the 3D PHONIC function is activated
(see page 40).
Changing the
initial settings
D. RANGE COMPRESSION
When enjoying a DVD VIDEO disc
recorded with the Dolby Digital
format at low or middle volume,
this setting makes you hear sound
comfortably.
Downloaded From DvDPlayer-Manual.com JVC Manuals
61
Changing the initial settings
SPK.SETTING page
This setting allows you to select desired options concerning with the speakers.
SPK.SETTING
MODE
5.1 CH.
SIZE
DELAY
LEVEL
SELECT
ENTER
USE 5∞ TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
Menu items
MODE
You can select the speaker
configuration type according to
your speaker systems. Normally,
set to “5.1 CH.”
Setting options
Notes/examples
• 5.1 CH.
When you connect to a 5.1-channel
amplifier and use the front, rear,
center and sub-woofer speakers.
• When selecting “5.1 CH.,” set
“ANALOG OUT” to “MULTI
CHANNEL” in the “AUDIO”
preference display (see page 61).
• The Dolby Digital LEF (Low
• EXPERT
Frequency Effect) signal is always
When you want to make fine tuning
fed from the SUBWOOFER jack on
to match your speakers. The SIZE,
the rear panel of the unit regardless
DELAY, and LEVEL setting items are
of speaker setting.
available.
• If you connect the unit’s digital
output to an external Dolby Digital
or DTS decoder (and set “DIGITAL
AUDIO OUTPUT” to “STREAM/
PCM” in the “AUDIO” preference
display), the speaker settings shown
left is not effective. Make the
speaker settings of the external
decoder properly.
SIZE
You can set the speaker sizes
according to your speakers.
See page 64 for details about the
speaker size setting.
(SIZE display)
SIZE
FRONT SPEAKER
LARGE
CENTER SPEAKER
SMALL
REAR SPEAKER
SMALL
BASS REDIRECT
SUB WOOFER
RETURN
SELECT
ENTER
DELAY
You can set the speaker delay time
according to your speakers.
See page 64 for details about the
speaker delay time setting.
USE 5∞ TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
(DELAY display)
DELAY
CENTER SPEAKER
0.0m/ 0ft
REAR SPEAKER
0.0m/ 0ft
Changing the
initial settings
RETURN
SELECT
ENTER
LEVEL
You can set the speaker output level
according to your speakers.
See page 65 for details about the
speaker output level setting.
USE 5∞ TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
(LEVEL display)
LEVEL
FRONT SPEAKER
0dB
CENTER SPEAKER
0dB
REAR SPEAKER
0dB
SUB WOOFER
0dB
TEST TONE
OFF
RETURN
SELECT
ENTER
62
Downloaded From DvDPlayer-Manual.com JVC Manuals
USE 5∞ TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
Changing the initial settings
English
OTHERS page
This page allows you to select desired options concerning with the system.
OTHERS
RESUME
ON
ON SCREEN GUIDE
ON
AUTO STANDBY
OFF
AV COMPULINK MODE
DVD1
PARENTAL LOCK
SELECT
ENTER
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
Menu items
Setting options
Notes/examples
RESUME
• ON
• See page 20 for details about
You can select the resume playback
resume playback function.
The unit can resume playback of the
mode.
disc from the position you
interrupted playback last time if it is
still on the tray.
• OFF
The resume function is not active.
ON SCREEN GUIDE
The unit can display “on-screen
guide” icons or characters on the
picture, which show what is
happening to the disc or the unit.
• ON
• See page 18 about on-screen guide
icons.
The on-screen guide will be displayed.
• Examples of “on-screen guide”
• OFF
icons or characters:
,
,
The on-screen guide will not be
displayed.
AUTO STANDBY
When the unit is stopped for more
than 30 minutes or 60 minutes, the
unit enters standby mode
automatically.
OFF j 60 j 30
AV COMPULINK MODE
If you use the AV COMPU LINK
system, you must set this item
correctly.
DVD 1j DVD 2 j DVD 3
• See page 71 for details about AV
COMPU LINK function.
PARENTAL LOCK
When selecting this option,
pressing ENTER on the remote
control unit brings up the
“PARENTAL LOCK” display shown
right, in which you can restrict
playback of DVD VIDEO discs for
children.
See page 66 for details about the
Parental Lock setting.
(PARENTAL LOCK display)
PARENTAL LOCK
COUNTRY CODE
US
SET LEVEL
NONE
PASSWORD
____
EXIT
SELECT
Changing the
initial settings
• DISC RESUME
The unit can resume playback of
last 30 discs (the unit keeps
memory positions even if a disc is
removed from the tray).
NEW PASSWORD? ... PRESS 0 ~ 9 KEY
ENTER
Downloaded From DvDPlayer-Manual.com JVC Manuals
63
Changing the initial settings
Making fine tuning for your
speakers
You can make fine tuning to match your speaker system.
This adjustment is available only when “ANALOG OUT”
is set to “MULTI CHANNEL” in the “AUDIO” preference
display and “MODE” is set to “EXPERT” in the “SPK.
SETTING” preference display.
To set the speaker sizes
You can set the speaker sizes according to your
speakers.
CLOSE
TV1
TV2
TV3
1
2
3
TV4
TV5
TV6
5
TV8
7
8
9
TV-/--
TV0
MUTING
10
0
PAGE
T
RETURN
6
TV9
TV/VIDEO
CANCEL
5/∞
ME
NU
VOL-
VOL+
ENTER
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
N
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
ANGLE
3D
PHONIC
ZOOM
1 Use 5/∞ to move
to [SIZE] and press
ENTER.
The SIZE display page appears on the TV screen.
points to [FRONT SPEAKER].
See page 56 for details about how to bring up the
“SPK.SETTING” page.
FRONT SPEAKER
LARGE
CENTER SPEAKER
SMALL
REAR SPEAKER
SMALL
BASS REDIRECT
SUB WOOFER
RETURN
Changing the
initial settings
When you use the small speakers which do not fully
reproduce the low-frequency range, you can boost up
the low-frequency signal of the subwoofer or front
speakers.
1 Use 5/∞ to select [BASS REDIRECT] and
press ENTER.
SUB WOOFER: The low-frequency signal fed from
the subwoofer output is boosted
up.
FRONT L/R:
The low-frequency signals fed from
the front speaker outputs are
boosted up.
The “BASS REDIRECT” setting is effective only
when at least any one of the speaker sizes is set to
“SMALL.” If none of them is set to “SMALL,” this
setting is no activated.
(“NONE” appears in the setting field.)
Please note that the “FRONT L/R” setting is
effective only when playing back a Dolby Digital
encoded DVD VIDEO disc. If the front speaker size is
set to “SMALL,” the “BASS REDIRECT” setting is
fixed to “SUB WOOFER.”
To set the delay time
SIZE
SELECT
BASS REDIRECT function
AMP VOL
¶ While the “SPK.SETTING” page of the preference
display is shown
ENTER
• If you set the “FRONT SPEAKER” to “SMALL”, you
cannot set the other speakers to “LARGE”.
L/R] and press ENTER.
+10
NU CH
ME
+
OP
NOTE
2 Use 5/∞ to select [SUB WOOFER] or [FRONT
4
TV7
TITLE/
GROUP
• To return to the “SPK.SETTING” page
Use 5/∞ to move
to [RETURN] and press ENTER.
USE 5∞ TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
2 Use 5/∞ to select the speaker to be set and
You can adjust the delay time of each speaker.
Selecting each speaker distance, which is on the basis of
the distance between the front speakers and the
listening position, sets an appropriate delay time. Check
that what the distance to each speaker is and set distance
values following the procedure.
press ENTER.
TV
FRONT SPEAKER: Front speakers
CENTER SPEAKER: Center speaker
REAR SPEAKER:
Rear speakers
LARGE: Large speaker(s) which can fully
reproduce the low-frequency range.
SMALL: Small speaker(s) which cannot fully
reproduce the low-frequency range.
NONE: No speaker(s) connected. This option is
only for “CENTER SPEAKER” and “REAR
SPEAKER.”
4 Repeat steps 2 and 3 if you set other
speakers.
64
Downloaded From DvDPlayer-Manual.com JVC Manuals
TV
TV1
TV2
TV3
1
2
3
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
T
DVD
TV4
RETURN
3 Use 5/∞ to select the size and press ENTER.
DVD
STANDBY/ON
OPEN/
CLOSE
0
PAGE
+10
TITLE/
GROUP
NU CH
ME
+
OP
TV/VIDEO
CANCEL
ME
NU
VOL-
VOL+
ENTER
5/∞
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
N
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
3D
PHONIC
ANGLE
ZOOM
AMP VOL
¶ While the “SPK.SETTING” page of the preference
display is shown
Changing the initial settings
1 Use 5/∞ to move
to [DELAY] and press
1 Use 5/∞ to move
to [LEVEL] and press
ENTER.
ENTER.
The DELAY display page appears on the TV screen.
points to [CENTER SPEAKER].
See page 56 for details about how to bring up the
“SPK.SETTING” page.
The LEVEL display page appears on the TV screen.
points to [CENTER SPEAKER].
See page 56 for details about how to bring up the
“SPK.SETTING” page.
English
LEVEL
DELAY
CENTER SPEAKER
0.0m/ 0ft
FRONT SPEAKER
0dB
REAR SPEAKER
0.0m/ 0ft
CENTER SPEAKER
0dB
REAR SPEAKER
0dB
SUB WOOFER
0dB
TEST TONE
OFF
RETURN
RETURN
SELECT
SELECT
USE 5∞ TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
ENTER
ENTER
2 Use 5/∞ to select the speaker to be set and
USE 5∞ TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
2 Use 5/∞ to select the speaker to be set and
press ENTER.
press ENTER.
CENTER SPEAKER: Center speaker
REAR SPEAKER: Rear speakers
FRONT SPEAKER: Front speakers (This item
cannot be selected. The level is
fixed to 0dB.)
CENTER SPEAKER: Center speaker
REAR SPEAKER:
Rear speakers
SUB WOOFER:
Subwoofer speaker
3 Use 5/∞ to select the delay time and press
ENTER.
When you select “CENTER SPEAKER,” you can
select the delay time from “0.0m/0ft” to
“1.5m/5ft” in 1ft units.
When you select “REAR SPEAKER,” you can select
the delay time from “0.0m/0ft” to “4.5m/15ft” in 1ft
units.
4 Repeat steps 2 and 3 if you set other
speakers.
• To return to the “SPK. SETTING” page
Use 5/∞ to move
to [RETURN] and press ENTER.
3 Use 5/∞ to set the level and press ENTER.
When you select “CENTER SPEAKER,” “REAR
SPEAKER” or “SUB WOOFER,” you can select the
level from –6 to 6dB in 1dB units.
4 Repeat steps 2 and 3 if you set other
speakers.
• To return to the “SPK.SETTING” page
Use 5/∞ to move
to [RETURN] and press ENTER.
NOTE
NOTE
• For the speaker(s) whose size is set to “NONE,” the
delay time cannot be set.
• For the speaker(s) whose size is set to “NONE,” the
speaker level cannot be set.
To set the speaker level
You can check the level setting by monitoring the test
tone.
You can adjust the output level of each speaker.
1 Use 5/∞ to select [TEST TONE] and press
TV
STANDBY/ON
OPEN/
CLOSE
TV
TV1
DVD
TV2
2
3
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
10
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
The test tone will be generated when you select the
speaker(s) in the “LEVEL”display.
MUTING
0
PAGE
2 Use 5/∞ to select [ON] and press ENTER.
TV3
1
TV4
RETURN
T
ENTER.
DVD
Changing the
initial settings
To generate test tone signals
5/∞
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
N
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
3D
PHONIC
ANGLE
ZOOM
AMP VOL
RM-SXV011J
REMOTE CONTROL
¶ While the “SPK.SETTING” page of the preference
display is shown
Downloaded From DvDPlayer-Manual.com JVC Manuals
65
Changing the initial settings
This function restricts playback of DVD VIDEO discs
which contain violent (and other) scenes according to the
level set by the user. For example, if a movie which
includes violent scenes supports the parental lock
feature, such scenes which you do not want to let
children view can be cut or replaced with other scenes.
When selecting “PARENTAL LOCK” in the “OTHERS”
page of the preference display (see page 63), pressing
ENTER on the remote control unit brings up the
PARENTAL LOCK sub-page shown below, in which you
can make setting for limiting playback.
To set Parental Lock for the first time
[PARENTAL LOCK]
Available :
TV
DVD
STANDBY/ON
OPEN/
CLOSE
TV
TV1
DVD
TV2
TV3
1
2
3
TV4
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
+10
PAGE
RETURN
T
Limiting playback by
children
TITLE/
GROUP
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
5/∞
N
STROBE
SLOW+
SLOW-
REPEAT SUB TITLE AUDIO
(OTHERS display)
Numeric
buttons
TV/VIDEO
CANCEL
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
3D
PHONIC
ANGLE
ZOOM
AMP VOL
OTHERS
RESUME
ON
ON SCREEN GUIDE
ON
AUTO STANDBY
60
AV COMPULINK MODE
DVD1
RM-SXV011J
REMOTE CONTROL
PARENTAL LOCK
SELECT
ENTER
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
Press ENTER.
(PARENTAL LOCK display)
PARENTAL LOCK
COUNTRY CODE
US
SET LEVEL
NONE
PASSWORD
____
EXIT
¶ While the “OTHERS” page of the preference display is
shown
1 Use 5/∞ to move
to [PARENTAL LOCK]
and press ENTER.
The Parental Lock on-screen display appears on the
TV screen.
points to [COUNTRY CODE].
See page 56 for details about how to bring up the
“OTHERS” page.
2 While
points to [COUNTRY CODE], press
ENTER to bring up the pull-down menu.
3 Use 5/∞ to select the country code.
SELECT
NEW PASSWORD? ... PRESS 0 ~ 9 KEY
Changing the
initial settings
ENTER
The country code whose standards were applied to
rate the DVD VIDEO disc should be selected.
See “Appendix A: Country/Area code list for
Parental Lock” on page 76.
PARENTAL LOCK
COUNTRY CODE
US
UG
SET LEVEL
NONE
UM
PASSWORD
____
EXIT
UZ
VC
SELECT
USE 5∞ TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
4 Press ENTER.
moves to [SET LEVEL].
66
UY
VA
ENTER
Downloaded From DvDPlayer-Manual.com JVC Manuals
US
Changing the initial settings
5 While
points to [SET LEVEL], press ENTER
to bring up the pull-down menu.
In the pull-down menu, “NONE” and level “1”
through “8” are available.
“NONE” does not restrict playback. Level “1” is the
strictest level. Discs rated higher than the selected
level are restricted.
Available :
You can change the Parental Lock settings later.
TV
US
NONE
SET LEVEL
NONE
8
PASSWORD
____
EXIT
6
5
4
USE 5∞ TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
TV2
TV3
1
2
3
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
0
PAGE
RETURN
T
SELECT
DVD
TV4
10
3
ENTER
TV
TV1
7
DVD
STANDBY/ON
OPEN/
CLOSE
PARENTAL LOCK
COUNTRY CODE
English
To change the settings
[PARENTAL LOCK]
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
NU CH
ME
+
OP
ME
NU
VOL-
VOL+
ENTER
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
6 Use 5/∞ to select a desired parental lock
CLEAR
SELECT
5/∞
N
STROBE
SLOW+
SLOW-
level, then press ENTER.
Numeric
buttons
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
moves to [PASSWORD].
DIGEST
3D
PHONIC
7 Enter your 4-digit password using the numeric
ANGLE
ZOOM
AMP VOL
RM-SXV011J
REMOTE CONTROL
buttons (0 to 9).
¶ While the “OTHERS” page of the preference display is
shown
PARENTAL LOCK
COUNTRY CODE
US
SET LEVEL
NONE
PASSWORD
1234
EXIT
1 Use 5/∞ to move
to [PARENTAL LOCK]
and press ENTER.
SELECT
NEW PASSWORD? ... PRESS 0 ~ 9 KEY
ENTER
8 Press ENTER.
The setting is set.
moves to [EXIT].
Pressing ENTER again returns to the “OTHERS”
page of the preference display.
The Parental Lock on-screen display appears on the
TV screen.
points to [PASSWORD].
See page 63 for details about how to bring up the
“OTHERS” page.
PARENTAL LOCK
COUNTRY CODE
US
SET LEVEL
NONE
PASSWORD
____
EXIT
SELECT
NEW PASSWORD? ... PRESS 0 ~ 9 KEY
ENTER
2 Enter your current 4-digit password using the
numeric buttons (0 to 9) and press ENTER.
moves to [COUNTRY CODE] if you enter the
correct password.
If you enter the wrong password, “WRONG!
RETRY...” appears on the TV screen, and you
cannot go to the next step.
Downloaded From DvDPlayer-Manual.com JVC Manuals
Changing the
initial settings
• If you enter an undesired password in step 7, reenter the
password before pressing ENTER.
67
Changing the initial settings
3 To change the “COUNTRY CODE” or
“SET LEVEL”, press ENTER to bring up the
associated pull-down menu while
points
the appropriate item.
To select the item to be set, use 5/∞ when no pulldown menu is shown.
4 Use 5/∞ to select a desired option and press
ENTER.
Note that if you change the country code, you must
reselect the Parental Lock level.
To temporarily release the Parental
Lock [PARENTAL LOCK]
Available :
When you set the parental level strictly, some discs may
not be played back at all. When you insert such a disc
and try to play it, the following Parental Lock on-screen
display appears on the TV screen, asking you whether
you want the Parental Lock to be temporarily released or
not.
5 While
points to [PASSWORD], enter a 4-digit
password using the numeric buttons (0 to 9).
TV
TV
TV1
The password entered in the above step becomes
the new password. If you do not change the
password, enter the same password as in the step 2.
Even if you want to change only the country code
and/or parental level, do not forget to enter the
password after changing the country code and/or
parental level. Otherwise, the new country code
and/or parental level will not become effective.
TV2
2
3
TV5
TV6
4
5
6
TV7
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
10
0
T
SUBTITLE
+10
TITLE/
GROUP
ME
NU
VOL-
VOL+
ENTER
Numeric
buttons
TV/VIDEO
CANCEL
NU CH
ME
+
OP
5/∞
ENTER
CH
OIC
E
CH
-
E
RE
SC
ON
NEXT
PREVIOUS
CLEAR
SELECT
N
STROBE
SLOW+
SLOW-
REPEAT SUBTITLE AUDIO
VFP
PROGRESSSIVE
SCAN
ANGLE
3D
PHONIC
moves to [EXIT].
Pressing ENTER again returns to the “OTHERS”
page of the preference display.
• If you forget your password in step 2
TV3
1
RETURN
6 Press ENTER.
• If you enter the wrong password more than three times
in step 2 above,
moves to [EXIT] automatically and
5/∞ does not work.
DVD
TV4
DIGEST
NOTES
DVD
STANDBY/ON
OPEN/
CLOSE
ZOOM
AMP VOL
RM-SXV008J
REMOTE CONTROL
1 Use 5/∞ to move
to [TEMPORARY
RELEASE], then press ENTER.
moves to the [PASSWORD].
When selecting [NOT RELEASE], press 0 OPEN/
CLOSE to remove the disc.
Enter “8888” The current password is deleted and you
can set a new password.
PARENTAL LOCK
TEMPORARY RELEASE
NOT RELEASE
PASSWORD
Changing the
initial settings
SELECT
ENTER
____
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE
2 Enter your 4-digit password using the numeric
buttons (0 to 9).
The Parental Lock is released, and the unit starts
playback.
If you enter the wrong password, “WRONG!
RETRY...” appears on the TV screen.
Enter the correct password.
NOTE
• When you enter the wrong password more than three
times in step 2 above,
moves to [NOT RELEASE]
automatically and 5/∞ does not work.
68
Downloaded From DvDPlayer-Manual.com JVC Manuals
Additional information
English
Names of parts and controls
Refer to the corresponding pages indicated in () for details.
Front panel
1 2
3
4
5
6
7 STOP
3 PLAY
7
8
DVD AUDIO/DVD VIDEO/SUPER VCD/VCD/CD PLAYER
0 OPEN/CLOSE
8 PAUSE
4
SKIP
¢
STANDBY/ON
STANDBY/ON
PROGRESSIVE DVD AUDIO
9
1
2
3
4
5
6
7
8
9
0
=
STANDBY/ON
button (14)
STANDBY/ON indicator (11, 14)
Disc tray (17, 19, 20)
0 OPEN/CLOSE button (17, 19, 20)
7 STOP button (18, 19, 47)
3 PLAY button (18, 20)
0
-
=
8 PAUSE button (18, 21)
4/¢ SKIP buttons (21, 22)
Display windows (see the illustration below)
Remote sensor (12)
PROGRESSIVE indicator (7, 8, 59)
DVD AUDIO indicator (17)
Display window
1
2
3
LPCM
MPEG
DOLBY
DIGITAL
DTS
VCDVD
38
4
5
1 A-B
GROUP TITLE TRACK CHAP
PROGRAM
RANDOM
7
6
1
2
3
4
5 Repeat mode indicators (33, 49, 55)
6 PROGRAM/RANDOM indicators (31, 33)
7 Multi-information window
Audio format indicators
Disc indicator
3 (play)/8 (pause) indicators
Group/title/track/chapter indicators
Rear panel
2 3
CENTER RIGHT
SUBWOOFER
PCM / STREAM
4
5
6
7
LEFT
REAR
RIGHT LEFT
8
1
AV COMPU LINK
COMPONENT
VIDEO
Y
PB
PR
AC IN
480p
REMOTE
480i
Additional
information
1
S-VIDEO
OPTICAL COAXIAL
DIGITAL OUT
AUDIO OUT
VIDEO OUT
9
1 AUDIO OUT jacks (RIGHT/LEFT/SUBWOOFER/
CENTER/REAR RIGHT/REAR LEFT) (6, 7, 9, 10)
2 VIDEO OUT - VIDEO jack (6)
3 VIDEO OUT - S-VIDEO jack (6)
4 VIDEO OUT - COMPONENT jacks (Y/PB/PR) (7)
5 Scanning mode selector (480i/480p/REMOTE) (6, 7, 8)
Downloaded From DvDPlayer-Manual.com JVC Manuals
6 AV COMPU LINK jacks (71)
7
AC IN connector (11)
8 Region code label (4)
9 DIGITAL OUT jacks (OPTICAL/COAXIAL) (10)
69
Additional information
Remote control unit
%
^
TV
DVD
STANDBY/ON
OPEN/
CLOSE
TV
DVD
1
2
TV1
TV2
1
2
3
TV4
TV5
TV6
4
5
6
TV8
TV9
7
8
9
TV-/--
TV0
MUTING
0
T
RETURN
OP
PAGE
NU
ME
+10
TITLE/
GROUP
TV/VIDEO
CANCEL
ME
NU
CH
+
VOL-
VOL+
ENTER
CH
N
8
TV3
TV7
10
3
4
5
6
7
CH
-
OI
CE
C
NS
RE
E
CLEAR
#
$
¡
™
9
~
!
@
(
)
_
+
O
NEXT
PREVIOUS
0
=
&
*
SELECT
STROBE
£
SLOW-
SLOW+
¢
REPEAT SUB TITLE AUDIO
VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST
ANGLE
3D
PHONIC
§
ZOOM
¶
AMP VOL
•
RM-SXV011J
Additional
information
REMOTE CONTROL
1
2
3
4
5
6
7
8
9
0
=
~
!
@
#
70
OPEN/CLOSE button (17, 19, 20)
Numeric buttons
RETURN button (27)
PAGE button (30)
TOP MENU button (26)
Cursor selection (5 Up, ∞ Down) CH (+/–) buttons (13)
Cursor selection (2 Left, 3 Right) VOL (+/–) buttons (13)
CHOICE button (15, 56)
4/PREVIOUS button (21, 22, 47, 52)
7/CLEAR button (18, 19, 32, 47)
3/SELECT button (18, 20, 25, 26, 47, 53)
1/SLOW– button (21)
REPEAT button (33, 49, 55)
SUBTITLE button (35)
DIGEST button (29)
3D PHONIC button (40)
Downloaded From DvDPlayer-Manual.com JVC Manuals
$
%
^
&
*
(
)
_
+
¡
ANGLE button (25, 37)
Infrared signal-emitting window (12)
TV - DVD switch (13, 14, 26, 47, 51, 56)
TV STANDBY/ON
button (13)
DVD STANDBY/ON
button (14)
TV/VIDEO - CANCEL button (13, 26, 32)
TITLE/GROUP button (27, 49, 54)
MENU button (26)
ENTER button
ON SCREEN button (24, 28, 31, 33, 34, 42)
¢/NEXT button (21, 22, 47, 52)
£ 8/STROBE button (18, 21, 38, 47)
¢ ¡/SLOW+ button (21)
AUDIO-fs/Rate button (36, 41, 50)
VFP - PROGRESSIVE SCAN button (8, 39)
ZOOM +/– buttons (39, 53)
AMP VOL +/– buttons (13)
Additional information
English
AV COMPU LINK remote control system
The JVC AV COMPU LINK system allows you to enjoy video or audio with the simplest
operation.If your video/audio player (such as a DVD player, CD player and VCR) and
television or/and amplifier/receiver support the JVC AV COMPU LINK system and are tied
with the JVC AV COMPU LINK cable(s), when you simply starting the player, all the
necessary settings of the television and/or amplifier/receiver for enjoying playback are
automatically performed.
Connection and setup
To AV COMPU LINK
(II, EX or III)
Using the AV COMPU LINK cable, connect the AV
COMPU LINK terminals of each component to one
another.
• The unit’s AV COMPU LINK setting is operated in the
OTHERS page in the preference display. See page 63
for operation.
• For information on the connection between the TV and
the receiver, refer to the receiver’s Instructions.
TV
Receiver
To AV COMPU LINK
The unit
• If you connect the unit to a television and receiver via
AV COMPU LINK, set the unit’s AV COMPU LINK
setting to DVD1.
IMPORTANT!
To AV COMPU LINK (II, EX or III)
TV
The unit
• If you connect the unit to a television via AV COMPU
LINK, set the unit’s AV COMPU LINK setting as follows.
• When connecting to VIDEO-1 input terminal of
the television: DVD2
• When connecting to VIDEO-2 input terminal of
the television: DVD3
• When you make video connection between the unit and
another device (such as a receiver and TV) via the
composite, S-video or component jacks, as well as AV
COMPU LINK connection, see also the instruction
manual of the other device.
Notes for connection
• If you connect the unit to a receiver via AV COMPU LINK
in a system including a Dolby Digital decoder, some
functions may not be performed automatically.
• Connect the AUDIO OUT jacks of the unit to the audio
input jacks of a receiver that indicating “DVD.”
Otherwise, the system will not work correctly.
• There may be no description about connections to the
unit in the instruction manual of a television or VCR.
However a television or VCR with AV COMPU LINK
terminals indicating “II,” “EX” or “III” can be connected
to the unit.
To AV COMPU LINK
(II, EX or III)
TV
To AV COMPU LINK
VCR
• If you connect the unit to a television and VCR via AV
COMPU LINK, set the VCR’s Remote Control Code and
the unit’s AV COMPU LINK setting as follows.
• When connecting to VIDEO-1 input terminal of
the television:
The unit’s AV COMPU LINK setting: DVD2
VCR’s Remote Control Code: B
• When connecting to VIDEO-2 input terminal of
the television:
The unit’s AV COMPU LINK setting: DVD3
VCR’s Remote Control Code: A
Downloaded From DvDPlayer-Manual.com JVC Manuals
Operation
You can enjoy pictures and/or sound by just putting a
source component (which plays back the pictures and/or
sound such as a DVD player or VCR) into play mode. You
do not have to operate the TV and receiver including not
having to perform power switching.
1 Turn on the main power of the television.
2 Insert a disc (or tape) into the source
Additional
information
The unit
component.
3 Press 3 of the source component.
The following actions are performed automatically:
• Turning on the power for the television.
• Setting the source of the television to the external
input (VIDEO-1 or VIDEO-2).
• Turning on the power for the receiver.
• Setting the source of the receiver to the component
which has started playback.
71
Additional information
Troubleshooting
What appears to be a malfunction may not always be serious. Please go through the following list before requesting service.
POWER
Symptom
Power does not come on.
Possible cause
Power plug is not inserted securely.
Remedy
Plug in securely.
OPERATION
Symptom
The remote control unit does not work.
Possible cause
Remedy
Too far from the unit.
More closer to the unit.
The tip of the remote control unit is not
pointed in the right direction.
Point the infrared light- emitting window
toward the remote sensor on the front
panel (see page 12).
Batteries are exhausted.
Replace the batteries with new ones.
Battery polarity is incorrect.
Take out the batteries and insert them again
in the correct direction.
The remote control unit is not set for
operating your TV.
Set the remote control unit for operating
your TV (see page 14).
The TV/VIDEO - CANCEL, 5/∞/2/3 or
numeric buttons do not work.
The TV - DVD switch is not correctly set.
To control the unit, set the TV - DVD switch
to “DVD.” To control your TV, set the TV DVD switch to “TV” (see page 13).
Operation is not possible.
Microcomputer malfunction due to
lightning or static electricity.
Turn off the power and unplug the power
cord, then connect the power cord again.
Moisture condensation caused by a sudden Turn off the power, then turn it on a few
change of temperature or humidity.
hours later.
Check and replace the disc (see page 4).
The disc does not allow the operation
because of disc contents.
Try to press 7 and select a title using the
numeric buttons on the remote control
unit.
Additional
information
When using the TITLE/GROUP button to
select a title during DVD VIDEO playback,
appears on the TV screen and the title
cannot be selected.
The disc does not allow the operation.
Or a non-playable disc is loaded.
72
Downloaded From DvDPlayer-Manual.com JVC Manuals
Additional information
English
PICTURE
Symptom
No picture is displayed on the monitor.
Possible cause
Remedy
Connection of video cable is incorrect.
Connect the cable correctly.
Input selection of TV is incorrect.
Select correctly.
Disc is not playable.
Use a playable disc (see page 4).
No picture is displayed on the monitor or
the screen is blurred or divided into two
parts.
The unit is in the progressive scanning
mode (i.e. the PROGRESSIVE indicator is
lit) though it is connected to a TV via the
VIDEO or S-VIDEO jack.
Set the Scanning mode selector on the rear
panel to “480i,” or set it to “REMOTE” and
make the Progressive scanning mode
inactive by using the VFP-PROGRESSIVE
SCAN button (see pages 7 and 8).
A picture is noisy or blurred.
The unit is connected to a VCR directly and
the copyguard function is activated.
Connect the unit so that the picture signal
flows directly to the TV.
With some discs, a picture may be blurred
when setting “PROGRESSIVE MODE” to
“FILM” or “AUTO.”
Set “PROGRESSIVE MODE” to “VIDEO”
(see page 59).
“MONITOR TYPE” is not correctly set.
Select monitor type correctly (see page 59).
Television is not correctly set.
Set the television correctly.
It depends on the setting on the TV.
Adjust the TV screen using the control on
the TV.
A picture does not fit the television screen.
The upper and lower parts of the
preference display are cut off when using
wide-aspect TV.
AUDIO
Symptom
No audio is reproduced.
Possible cause
Remedy
Connection is incorrect.
Check the connection.
Input selection of amplifier is incorrect.
Select correctly.
Turn up the volume of the TV or amplifier/
receiver.
Note that you should turn down the volume
before switching back to TV broadcasting,
to prevent outputting the sudden big
sound.
Sound is distorted or noise is generated.
Disc is dirty.
Wipe the disc surface (see page 5).
“MULTI CH” is shown in the display
window when playing back a DVD AUDIO
disc.
The track is prohibited from down-mixing
to 2-channel stereo audio.
Listen in multichannel surround audio.
Additional
information
Audio volume is low when playing back the The audio level recorded on a DVD VIDEO
unit, compared with the TV or VCR.
is lower, compared with TV broadcasting.
Downloaded From DvDPlayer-Manual.com JVC Manuals
73
Additional information
Frequently Asked Questions
Question
Answer
Ref. page
You can play back the DVD VIDEO discs with the Region
Code (local code) containing “ALL” or “1” recorded in
the NTSC or PAL system (PAL disc signals are
reproduced by converting to the NTSC system). You can
also play back the Video CD discs recorded in the NTSC
system. Please check the information on each disc jacket.
4
Can I play back a DVD VIDEO disc without any Region
Code number?
The Region code indicates the conformity of the disc to
the standards.
Any DVD VIDEO not conforming to the standards cannot
be played back.
4
Can I play back a CD-R/RW disc with still pictures in other
than the JPEG format?
No, you cannot play back that disc.
Can I play back audio on a disc labeled “Dolby Digital
EX”?
Yes, you can play back the disc because Dolby Digital EX
is compatible with Dolby Digital. However, to get the
maximum performance of Dolby Digital EX, we
recommend to connect the DIGITAL OUT jack to a
decoder or amplifier/receiver with built-in decoder that
supports Dolby Digital EX. In this case, set “DIGITAL
AUDIO OUTPUT” on the “AUDIO” preference display to
“STREAM/PCM.”
60
Can I play back audio on a disc labeled “DTS ES”?
Is there any difference in the playback settings between
Discrete and Matrix recording systems for DTS ES?
Though you cannot enjoy audio using the analog audio
outputs (AUDIO OUT), you can enjoy DTS ES audio by
connecting the DIGITAL OUT jack to a decoder or
amplifier/receiver with built-in decoder that supports
DTS ES. In this case, set “DIGITAL AUDIO OUTPUT” on
the “AUDIO” preference display to “STREAM/PCM.”
60
Can this unit play back a disc labeled “THX”?
What does “THX” mean?
Yes you can. “THX” is a name of the original standard for
high quality picture/audio recording and playback
established by Lucasfilm Ltd. A disc labeled “THX” is
certified that it passed this standard.
When files of the MP3 and Audio CD formats are
recorded on a same disc, can the unit play back files of
both formats?
The disc is of the data CD format, therefore, the unit can
play back only files of the MP3 format.
Some Dolby Digital discs contain 5.1-ch Surround or
Dolby Surround audio data. What is the difference
between these two types?
Both are surround sound standards developed by Dolby
Laboratories Inc. in the U.S.A.
Dolby Surround records 2-channel surround audio
information are recorded onto the analog stereo (left and
right) channels together with front stereo audio
information. When played back, the surround signals are
separated by a Dolby Surround or Dolby Pro Logic
decoder.
Dolby Digital digitally encodes and records up to six
channel information for left, right, center, rear left, rear
right and LFE (Low-Frequency Effect for Sub-woofer etc.).
When played back, a Dolby Digital decoder decodes data
and outputs signals separately.
Generally, Dolby Digital sounds better.
Additional
information
Can I play back DVD VIDEO and Video CD purchased
abroad?
74
When playing back a DVD VIDEO or Video CD disc,
something like mosaic appears on the TV screen. Is this
because of a malfunction of the unit?
It is a block noise specific to a motion picture recorded in
digital, and is not a malfunction of the unit.
The unit does not function as described in this
Instruction Manual.
The operation of this unit may occasionally be
unacceptable due to the intention of the disc contents
creator and/or structural restrictions.
Can I record DVD VIDEO data on a video tape?
Most of all DVD VIDEO discs are copy-protected so that
you cannot record DVD VIDEO data onto any video tape.
Can this unit record data?
No, you cannot.
Downloaded From DvDPlayer-Manual.com JVC Manuals
4
4, 47
4
3
Additional information
English
Specifications
*Specifications and appearance subject to change without prior notice.
General
Readable discs:
Video format:
DVD AUDIO, DVD VIDEO, DVD-R (Video format), SVCD, Video CD, Audio CD (CD-DA), MP3
Format, JPEG, CD-R/RW (CD-DA, SVCD, Video CD, MP3 Format, JPEG)
NTSC, 480i (Interlaced scan)/480p (Progressive scan) selectable
Other
Power requirements:
Power consumption:
Mass:
Dimensions (W x H x D):
AC 120 V
, 60 Hz*
14 W (POWER ON), 2.0 W (STANDBY mode)
2.5 kg (5.6 lbs)
435 mm x 73 mm x 267.5 mm
(17-3/16 inch x 2-7/8 inch x 10-9/16 inch)
Video outputs
COMPONENT (pin jacks):
VIDEO OUT (pin jack):
S-VIDEO OUT (S jack):
Horizontal resolution:
Y Output:
PB/PR Output:
1.0 Vp-p (75 Ω)
Y Output:
C Output:
500 Lines or more
1.0 Vp-p (75 Ω)
0.7 Vp-p (75 Ω)
1.0 Vp-p (75 Ω)
286 mVp-p (75 Ω)
Audio outputs
ANALOG OUT (pin jack):
DIGITAL OUT: (COAXIAL):
(OPTICAL):
2.0 Vrms (10 kΩ)
0.5 Vp-p (75 Ω termination)
–21 dBm to –15 dBm (peak)
Audio characteristics
Frequency response:
Dynamic range:
Wow and flutter:
Total harmonic distortion:
CD
DVD
(sampling frequency 44.1 kHz):
2 Hz to 20 kHz
(sampling frequency 48 kHz):
2 Hz to 22 kHz
(2 Hz to 20 kHz for DTS and Dolby Digital bitstream signals)
DVD (sampling frequency 96kHz/88.2 kHz): 2 Hz to 44 kHz
DVD (sampling frequency 192kHz/176.4 kHz):2 Hz to 88 kHz
16 bit: More than 98 dB
20/24 bit: More than 110 dB
Unmeasurable (less than ± 0.002%)
16 bit: Less than 0.0018%
20/24 bit: Less than 0.0012%
Additional
information
*Notes for PX model (Check the specification indication on the rear panel.):
Power requirements : AC 110V - 240V
, 50Hz/60Hz
Power consumption : 15W (POWER ON), 3.4W (STANDBY mode)
Downloaded From DvDPlayer-Manual.com JVC Manuals
75
Additional information
Appendix A: Country/Area code list for Parental Lock
This list is used for the Parental Lock operation. For details, see page 66.
Additional
information
AD
AE
AF
AG
AI
AL
AM
AN
AO
AQ
AR
AS
AT
AU
AW
AZ
BA
BB
BD
BE
BF
BG
BH
BI
BJ
BM
BN
BO
BR
BS
BT
BV
BW
BY
BZ
CA
CC
CF
76
Andorra
United Arab Emirates
Afghanistan
Antigua and Barbuda
Anguilla
Albania
Armenia
Netherlands Antilles
Angola
Antarctica
Argentina
American Samoa
Austria
Australia
Aruba
Azerbaijan
Bosnia and Herzegovina
Barbados
Bangladesh
Belgium
Burkina Faso
Bulgaria
Bahrain
Burundi
Benin
Bermuda
Brunei Darussalam
Bolivia
Brazil
Bahamas
Bhutan
Bouvet Island
Botswana
Belarus
Belize
Canada
Cocos (Keeling) Islands
Central African
Republic
CG Congo
CH Switzerland
CI
Cô te d'Ivoire
CK Cook Islands
CL Chile
CM Cameroon
CN China
CO Colombia
CR Costa Rica
CU Cuba
CV Cape Verde
CX Christmas Island
CY Cyprus
CZ Czech Republic
DE Germany
DJ Djibouti
DK Denmark
DM Dominica
DO Dominican Republic
DZ Algeria
EC Ecuador
EE Estonia
EG Egypt
EH Western Sahara
ER Eritrea
ES
ET
FI
FJ
FK
FM
Spain
Ethiopia
Finland
Fiji
Falkland Islands
Micronesia
(Federated States of)
FO Faroe Islands
FR France
FX France, Metropolitan
GA Gabon
GB United Kingdom
GD Grenada
GE Georgia
GF French Guiana
GH Ghana
GI
Gibraltar
GL Greenland
GM Gambia
GN Guinea
GP Guadeloupe
GQ Equatorial Guinea
GR Greece
GS South Georgia and the
South Sandwich
GT Guatemala
GU Guam
GW Guinea-Bissau
GY Guyana
HK Hong Kong
HM Heard Island and
McDonald Islands
HN Honduras
HR Croatia
HT Haiti
HU Hungary
ID
Indonesia
IE
Ireland
IL
Israel
IN
India
IO
British Indian Ocean
Territory
IQ
IR
Iraq
Iran (Islamic Republic
of)
IS
Iceland
IT
Italy
JM Jamaica
JO Jordan
JP Japan
KE Kenya
KG Kyrgyzstan
KH Cambodia
KI
Kiribati
KM Comoros
KN Saint Kitts and Nevis
KP Korea, Democratic
People's Republic of
KR Korea, Republic of
KW Kuwait
KY Cayman Islands
KZ Kazakhstan
LA Lao People’s
Democratic Republic
Downloaded From DvDPlayer-Manual.com JVC Manuals
LB
LC
LI
LK
LR
LS
LT
LU
LV
LY
MA
MC
MD
MG
MH
ML
MM
MN
MO
MP
MQ
MR
MS
MT
MU
MV
MW
MX
MY
MZ
NA
NC
NE
NF
NG
NI
NL
NO
NP
NR
NU
NZ
OM
PA
PE
PF
PG
PH
PK
PL
PM
PN
PR
PT
PW
PY
QA
RE
RO
RU
RW
Lebanon
Saint Lucia
Liechtenstein
Sri Lanka
Liberia
Lesotho
Lithuania
Luxembourg
Latvia
Libyan Arab
Morocco
Monaco
Moldova, Republic of
Madagascar
Marshall Islands
Mali
Myanmar
Mongolia
Macau
Northern Mariana
Islands
Martinique
Mauritania
Montserrat
Malta
Mauritius
Maldives
Malawi
Mexico
Malaysia
Mozambique
Namibia
New Caledonia
Niger
Norfolk Island
Nigeria
Nicaragua
Netherlands
Norway
Nepal
Nauru
Niue
New Zealand
Oman
Panama
Peru
French Polynesia
Papua New Guinea
Philippines
Pakistan
Poland
Saint Pierre and
Miquelon
Pitcairn
Puerto Rico
Portugal
Palau
Paraguay
Qatar
Réunion
Romania
Russian Federation
Rwanda
SA
SB
SC
SD
SE
SG
SH
SI
SJ
Saudi Arabia
Solomon Islands
Seychelles
Sudan
Sweden
Singapore
Saint Helena
Slovenia
Svalbard and Jan
Mayen
SK Slovakia
SL Sierra Leone
SM San Marino
SN Senegal
SO Somalia
SR Suriname
ST Sao Tome and Principe
SV El Salvador
SY Syrian Arab Republic
SZ Swaziland
TC Turks and Caicos
Islands
TD Chad
TF French Southern
Territories
TG
TH
TJ
TK
TM
TN
TO
TP
TR
TT
TV
TW
TZ
Togo
Thailand
Tajikistan
Tokelau
Turkmenistan
Tunisia
Tonga
East Timor
Turkey
Trinidad and Tobago
Tuvalu
Taiwan
Tanzania, United
Republic of
UA Ukraine
UG Uganda
UM United States Minor
Outlying Islands
US United States
UY Uruguay
UZ Uzbekistan
VA Vatican City State
(Holy See)
VC Saint Vincent and the
Grenadines
VE Venezuela
VG Virgin Islands (British)
VI
Virgin Islands (U.S.)
VN Vietnam
VU Vanuatu
WF Wallis and Futuna
Islands
WS Samoa
YE Yemen
YT Mayotte
YU Yugoslavia
ZA South Africa
ZM Zambia
ZR Zaire
ZW Zimbabwe
Additional information
English
Appendix B: Glossary
Aspect ratio
A ratio which defines the shape of the rectangular
picture in a TV. It is the width of the picture relative to
the height. The conventional TV picture is 4:3 in
aspect ratio.
Bitstream
The digital form of multichannel audio data (e.g., 5.1channel) before it is decoded into its various channels.
Channel, CH
Stereo or multichannel audio consists of “channel”
signals. “Stereo” audio consists of left and right
channels, while 5.1-channel Dolby Digital consists of
six channels (front left, front right, rear left, rear right,
center and LFE (Low-Frequency Effect channel for subwoofer, etc.).
Chapter
The smallest division on DVD VIDEO. It is a division of
a title and similar to a track for Audio CD or Video CD.
Component video
Video signals with three channels of separate
information that makes up the picture. There are
some types of component video, such as R/G/B and Y/
CB(PB)/CR(PR).
Composite video
A single video signal commonly used in most
consumer video products that contains all luminance,
color, and synchronization information.
Dolby Digital (AC3)
A six-channel system consisting of left, center, right,
left rear, right rear and LFE (Low-Frequency Effect
channel for sub-woofer, etc.) channels. All processing
is done in the digital domain.
Not all Dolby Digital discs contain six (5.1) channel
information.
Dolby Surround/Dolby Prologic
Dolby Surround is a five-channel system consisting of
left, center, right and left rear, right rear channels. All
processing is done in the digital domain.
Dolby Prologic is a four-channel system consisting of
left, center, right and rear channel (the single rear
channel is usually played through two speakers).
Down-mix
Internal stereo mix of multichannel surround audio by
a DVD player. The down-mix signals are output from
stereo output connectors.
Downloaded From DvDPlayer-Manual.com JVC Manuals
DTS
A Digital Surround audio encoding format configured
with six (5.1) channels, similar to Dolby Digital. It
requires a decoder, either in the player or in an
external receiver. DTS stands for Digital Theater
Systems.
Not all DTS discs contain six (5.1) channel
information.
Dynamic range
The difference between the loudest and softest
sounds.
Dynamic range compression
The dynamic range compression (DRC) reduces the
dynamic range so that you can turn down the volume
to avoid disturbing others yet still hear the detail of
quiet passages.
Extension
Several letters at the end of a file name. File name
extensions usually follow a period and indicate the
type of information stored in the file.
Finalize
When conducting multisession recording, this means
the closing of a session (fixing) by indicating the
halting of writing so as to prevent the addition of any
more sessions.
Fs
See “Sampling frequency.”
Group
The largest division on DVD AUDIO.
ID3 tag
The tag embedded in an MP3 file indicating what
songs, artists, and album they comes from. You can
edit these tags.
Interlaced scan
In the conventional video system, a picture is shown
on the display monitor in two halves. The Interlaced
scanning system places lines of the second half of the
picture in-between lines of the first half of the picture.
ISO 9660 Format
The most common international standard for the
logical format for files and directories on a CD-ROM.
JPEG
A popular file format for still image compression.
JPEG stands for Joint Photographic Experts Group.
There are three sub-types of the JPEG format as
follows.
• baseline JPEG:
used for digital cameras, web,
etc.
• progressive JPEG: used for web.
• lossless JPEG:
an old type and rarely used
now.
Additional
information
480i/480p
Indicates the number of scanning lines and scanning
format of an image signal. 480i indicates 480 scanning
lines with interlace format, and 480p indicates 480
scanning lines with progressive format.
77
Additional information
Letter box
A type of picture playback with the normal (4:3) TV
screen. Black bars are shown at the top and bottom of
the image to allow playing of wide-screen (16:9) DVD
movie without cutting off any sides of the image on a
4:3 TV.
Linear PCM audio
Stands for “pulse code modulation.” Linear PCM is
the usual digital method without compression, used
for audio playback of DVD Video discs, Audio CD
discs, etc.
Menu
Most DVD AUDIO, DVD VIDEO or SVCD/Video CD
discs provide a menu, through which users can select
a desired playback material, condition, etc.
MLP
MLP stands for “Meridian Lossless Packing.” A
lossless audio compression system that can
completely recreate the PCM signal.
MP3
MP3 is an audio data reduction format, which stands
for MPEG-1 Audio Layer 3. Using MP3, you can
achieve a data reduction of about 1:10.
MPEG
A family of Standards for compressing audio-visual
information. “MPEG” standards include MPEG-1,
MPEG-2 and MPEG-4. Video CD and MP3 are based on
MPEG-1, while DVD is based on MPEG-2. MPEG
stands for Moving Picture coding Experts Group.
Multisession
A method of adding data to a CD-R/CD-RW in more
than one recording session using the Track-At-Once
method.
NTSC (National television system committee)
A black & white and color television system format
used in U.S.A., Canada, Mexico and Japan.
Packet Writing
A method of writing data on a CD-R/CD-RW in small
increments. Packets can be of fixed or variable length.
Additional
information
PAL (Phase Alternation by Line)
A color television system format used extensively in
Western Europe.
Pan scanning
A type of picture playback with the normal (4:3) TV
screen, which is panned and zoomed across the wider
movie picture, chopping off the left and right sides.
Parental lock
A DVD function that prevents undesired viewing by
children depending on disc contents. You need a
password to play back a locked disc in the normal
condition. Otherwise, undesirable scenes are
automatically skipped or replaced with other pictures.
78
Downloaded From DvDPlayer-Manual.com JVC Manuals
PBC
PBC stands for “Playback control” and is a method of
controlling disc play for Video CDs (VCD). You are able
to interact with the disc through menus.
Progressive scan
Progressive scanning displays all the horizontal lines
of a picture at one time, as a single frame. A
progressive-scanning DVD player converts the
interlaced (480i) video from DVD into progressive
(480p) format for connection to a progressive display.
It dramatically increases the vertical resolution.
Region code
Code identifying a geographic region of compatibility
for a DVD.
Sampling frequency
The rate at which measurements of an audio signal
are taken during A/D and D/A conversion. The
measure is samples per second.
Surround
An audio system with more than two (left and right)
channels, usually including rear channels, etc.
S-video
A video signal which improves picture quality over
standard composite connections. Used on Super VHS,
DVD, high end TV monitors, etc.
Title
The largest division on DVD VIDEO.
Track
The smallest division on DVD AUDIO, SVCD, Video CD
and Audio CD discs.
Transfer rate
The rate of transferring digital data. Usually the
measure is in baud per second. The DVD system
applies variable transfer rate system for high
efficiency.
Additional information
English
Appendix C: Index
3D PHONIC ................................................................ 40, 41, 61
480i............................................................................ 6, 7, 73, 75
480p .................................................................................... 7, 75
A
A-B repeat...................................................... 34, 35, 43, 44, 45
Angle..................................................................... 18, 37, 38, 45
Audio language.............................................. 18, 36, 44, 45, 57
Auto standby......................................................................... 63
AV COMPU LINK ................................................ 7, 9, 10, 63, 71
AV COMPULINK mode ......................................................... 63
B
Bonus group...................................................................... 5, 30
C
Chapter .................. 5, 22, 23, 24, 25, 26, 29, 33, 34, 35, 43, 44
Chapter search ...................................................................... 44
Component video .................................................... 2, 7, 71, 75
Copyguard system.................................................................. 3
Copy-protected disc................................................................ 6
Country code.............................................................. 66, 68, 76
D
D. range compression ..................................................... 10, 61
Digest..................................................................................... 29
Digital audio output......................................... 4, 10, 15, 16, 60
Direct selection ..................................................................... 49
Disc resume.......................................................... 18, 19, 20, 63
Dolby.................................................................................. 3, 71
Dolby Digital................................... 4, 10, 16, 41, 60, 61, 71, 75
DTS ............................................................... 3, 4, 10, 16, 60, 75
DVD menu ............................................................................. 26
DVD PLAYER SET UP............................................................. 15
Menu language ..................................................................... 57
Monitor type.............................................................. 15, 59, 73
MP3 ............................................................. 4, 47, 48, 49, 51, 60
MP3 CONTROL.......................................................... 48, 49, 57
MP3 disc ................................................................. 3, 20, 47, 57
MPEG .......................................................................... 16, 47, 60
Multi-angle part ............................................................... 37, 45
Multiple session............................................................... 47, 51
N
NTSC.............................................................................. 4, 8, 75
O
One touch replay function.................................................... 25
On-screen guide.............................................................. 18, 63
On-screen language ....................................................... 15, 57
Opening display......................................................... 14, 16, 17
P
Packet writing................................................................... 47, 51
PAL ........................................................................................... 4
Pan scanning ......................................................................... 59
Parental lock ................................................... 63, 66, 67, 68, 76
Playback control (PBC) ...... 5, 20, 22, 23, 26, 27, 28, 29, 33, 34
Preference .......................... 9, 10, 15, 16, 18, 19, 20, 35, 36, 37,
39, 47, 51, 56, 57, 66, 67, 68, 71, 73
Program (playback)................................. 29, 31, 32, 34, 43, 46
Progressive mode.................................................... 7, 8, 59, 73
Progressive scanning .................................. 7, 8, 39, 59, 73, 75
R
Random (playback) ................................................... 33, 43, 46
Region code ................................................................. 4, 14, 17
Repeat (playback)........................ 33, 34, 35, 43, 44, 45, 49, 55
Resume (playback)............................................... 18, 19, 20, 63
E
S
Extension.......................................................................... 47, 51
Sampling rate.......................................................................... 4
Scanning mode.................................................... 6, 7, 8, 59, 73
Screen saver.............................................................. 18, 51, 60
Slide show....................................................................... 53, 54
Slide show mode ............................................................ 53, 55
Slide show playback ....................................................... 53, 54
Slow-motion.............................................................. 18, 21, 25
Status bar ......................... 24, 25, 32, 35, 36, 37, 42, 43, 44, 45
Strobe (playback) .................................................................. 38
Subtitle language................................................ 18, 35, 36, 45
S-video...................................................................... 6, 7, 73, 75
F
Finalize.......................................................................... 4, 47, 51
G
Group....................................... 5, 22, 23, 24, 26, 27, 28, 32, 33,
43, 47, 48, 49, 51, 52, 54, 55
I
ID3 tag.................................................................................... 47
Initial setting............................................................... 15, 16, 56
Initial setup............................................................................. 15
Interlaced scanning ............................................................. 7, 8
ISO 9660 ........................................................................... 47, 51
J
JPEG ...................................................... 4, 47, 51, 52, 55, 57, 60
JPEG CONTROL .................................................. 52, 53, 54, 55
JPEG disc................................................... 3, 20, 51, 52, 53, 57
T
Time search................................................... 28, 29, 43, 44, 46
Transfer rate .................................................................... 24, 47
Transport status .............................................................. 24, 25
V
Additional
information
Numerics
VFP (Video fine prosessor)................................... 8, 39, 40, 73
L
Z
Language code...................................................................... 57
Linear PCM ........................................................................ 4, 60
Zoom (playback) ............................................................. 39, 53
M
Macrovision............................................................................. 3
Manufacturer code ................................................................ 13
Menu......................................... 5, 15, 17, 18, 23, 26, 27, 43, 44,
45, 56, 57, 59, 60, 61, 63, 66, 67, 68
Menu bar .................................... 25, 28, 29, 31, 32, 33, 34, 35,
36, 37, 38, 42, 43, 44, 45
Downloaded From DvDPlayer-Manual.com JVC Manuals
79
Authorized Service Centers
®
QUALITY
SERVICE
HOW TO LOCATE YOUR JVC SERVICE CENTER
TOLL FREE: 1 (800) 537-5722
http://www.jvc.com
Dear Customer,
In order to receive the most satisfaction from your purchase,please read the instruction booklet before
operating the unit.In the event that repairs are necessary, please call 1 (800)537-5722 for your nearest
authorized servicer or visit our website at www.JVC.com
Remember to retain your Bill of Sale for Warranty Service.
Do not service the television yourself
Caution
To prevent electrical shock,do not open the cabinet.There are no user serviceable
parts inside.Please refer to qualified service personnel for repairs.
Accessories
To purchase accessories for your JVC product,please call toll free:1 (800)882-2345 or
on the web at www.JVC.com
BT-51005-5
(0301)
Downloaded From DvDPlayer-Manual.com JVC Manuals
LIMITED WARRANTY
CONSUMER VIDEO 1-90
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE
ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date
of original retail purchase for the period as shown below. ("The Warranty Period")
PARTS
1
LABOR
YR
90
DAYS
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND
IN COMMONWEALTH OF PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner.
Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service
centers. Parts used for replacement are warranted only for the remainder of the Warranty Period. All products and parts
thereof may be brought to a JVC authorized service center on a carry-in basis except for Television sets having a screen
size 25 inches and above which are covered on an in-home basis.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized
service center, please call toll free: (800) 537-5722.
If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with
a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the
name and location of which will be given to you by the toll-free number.
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty
installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by
JVC to render such service, or if affixed to any attachment not provided with the products, or if the model number
or serial number has been altered, tampered with, defaced or removed;
2. Initial installation and installation and removal for repair;
3. Operational adjustments covered in the Owner's Manual, normal maintenance, video and audio head cleaning;
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;
5. Signal reception problems and failures due to line power surge;
6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;
7. Accessories;
8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);
There are no express warranties except as listed above.
THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS
LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER
DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE
TO TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH
OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an
implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific
legal rights and you may also have other rights which vary from state to state.
JVC COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
1700 Valley Road
Wayne, NJ 07470
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OF
REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION
PACKAGED WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. which is located either on the rear, bottom or side of the cabinet. Retain this information
for future reference.
Model No. :
Serial No. :
Purchase data :
Name of dealer :
Downloaded From DvDPlayer-Manual.com JVC Manuals
VICTOR COMPANY OF JAPAN, LIMITED
EN.
Downloaded From DvDPlayer-Manual.com JVC Manuals
V
J
C
0402KTYMDWJSC
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement