null  null
Use, Care, and Installation Guide
www.zephyronline.com
Okeanito
CO K-E36SX
CO K-E42SX
CO K-E48SX
Model number:
Serial number:
Date of Purchase:
Sales Dealer:
MAY07.0101 © Zephyr Corporation.
www.zephyronline.com
2
3
INSTALLATION
Ducting Calculation Sheet ...............................
Mounting Height and Clearance .....................
Ducting ..................................................................
Specifications .......................................................
Internal Blower ....................................................
Preparing Hood for External Blower ..............
Mounting the Hood ............................................
4
5
6
7
8-9
10 - 11
12 - 14
FEATURES & CONTROLS
Controls Overview .............................................. 15 - 16
MAINTENANCE
Cleaning ................................................................. 17
Lights ....................................................................... 18
TROUBLE SHOOTING ...................................... 19
LIST OF ACCESSORIES/PARTS ....................... 20
1
Ta ble of C ontents
SAFETY NOTICE ..............................................
LIST OF MATERIALS .......................................
www.zephyronline.com
Important safety Notice
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE TH E R IS K O F FIR E O R E LE C TR IC SHOC K, DO NOT USE TH IS FAN W ITH ANY S O LID-S TATE
SPE E D CONTROL DEV IC E.
WARNING
TO RE DUCE TH E R IS K O F FIR E, E LE C TR IC SH O C K, O R INJU RY TO P E R SON S, O B S E RVE TH E FO LLO W ING:
a. Use this unit only in the manner intended by the manufacturer, If you have questions, contact the manufacturer.
b. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being
switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a prominentwarning device, such as tag, to the service panel.
CAUTION
For General VentilatingUse Only. Do not Use to Exhaust Hazardous or Explosive Materials and Vapors.
Take care when using cleaning agents or detergents.Suitable for use in household cooking area.
WARNING
TO REDUC E TH E R IS K O F A RA NG E TO P GR E AS E FIR E:
a. Never leave surface units unattendedat high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low
or mediumsettings.
b. Always turn hood ON when cooking at high heat or when cooking flambeing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn
Beef Flambe)
c. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.
d. Use proper pan size. Always use cookware appropriatefor the size of the surface element.
WARNING
TO RE DUC E TH E R IS K O F INJURY TO P ERSON S IN TH E EV E NT O F A RA NG E TO P G R E AS E FIR E, O B S E RVE TH E FO LLOW ING :
a. SM OTHER FLA MES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. B E CARE FUL TO P R EV E NT BUR NS.
If the flames do not go out immediately,E VAC UATE AND CALL TH E FIR E DE PARTME NT.
b. NEV E R PIC K UP A FLAMI NG PAN - You may be burned.
c. DO NOT US E WATE R, includingwet dishcloths or towels - a violentsteam explosion will result.
d. Use an extinguisher ONLY if:
1. You know you have a class AB C extinguisher, and you already know how to operate it.
2. The fire is small and contained in the area where it started.
3. The fire departmentis being called.
4. You can fight the fire with your back to an exit.
5. Based on “Kitchen Fire Sa fety Tips” published by NFPA.
WARNING
TO R E DUC E TH E R IS K O F FIR E, E LE C TR IC SHOC K O R INJURY TO PER SONS, O B S E RVE TH E FO LLOW ING :
a. Installation Work and Electrical Wiring Must be Done by Qualified Person (s) In Accordance with all Applicable Codes and Standards,
Including Fire-Rated Construction.
b. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burningequipmentto prevent back
drafting. Follow the heating equipmentmanufacturer’s guideline and safety standards such as those published by the National Fire Protection
Association (NFPA), and the American S ociety for Heating, Refrigeration, and Air ConditioningEngineers (AS H R AE) and the local code authorities.
c. When cutting or drillinginto wall or ceiling, do not damage electrical wiring and other hidden utilities.
d. Ducted fans must always vent to the outdoors.
WARNING
TO REDUC E TH E R IS K O F FIR E, US E O NLY ME TAL DU C TW O R K.
CAUTION
To reduce risk of fire and to properly exhaust air, be sure to duct air outside - Do not vent exhaust air into spaces within walls or ceilings or into
attics, crawl spaces or garages.
CAUTION
To Reduce the Risk of Fire and Electric Shock, Install This Range Hood Only with Remote Blower Models C B E-1000 Rated
Maximum 6.2 amp, 120 Vac 60Hz or Integral Blowers Manufactured by Zephyr Ventilation, Models C B I-600.
2
1 - Hood
1 - Baffle Filter (2 on 48” model)
2 - 50W 120V Halogen Light Bulbs GU-10
2 - 40W 120V Appliance Bulbs
1 - Utensil Rail
2 - Telescopic Duct Covers
1 - Ceiling Mounting Bracket (pre attached to duct cover)
1 - Wall Mounting Bracket
1 - HARDWARE PACKET
7 - 2” Wood Screws
7 - Anchors
7 - 1/2” Washers
4 - 1/2” Screws 5x15mm
4 - 10mm Washers
1 - SMALL HARDWARE PACKET
1 - T ool
3 - Short Set Screws (4 on 48” Model)
1 - HARDWARE PACKET, EXTERNAL BLOWER KIT
1 - 8” Collar
1 - External Blower Wiring Box with Wires
10 - 1/2” Self Tapping Screws
10 - 4mm Internal Diameter Washers
NO DUCTING IS PROVIDED
EXTERNAL AND INTERNAL BLOWER SOLD SEPARATELY
Make sure to remove the protective film off of the hood before installation in order to make removal of the film
easier. Be careful not to scratch the stainless steel while installing.
3
Lis t of M a teria ls
MODEL: COK-ExxS
Ins ta lla tion - Ductwork C a lcula tion S heet
www.zephyronline.com
Equivalent number
length x used =
Duct pieces
Equivalent number
length x used =
Duct pieces
Total
Total
3 1/4” x 10”
Rect.,
straight
1 Ft.
x(
) =
Ft.
6” Round
30 Ft.
wall cap
with damper
x(
) =
Ft.
7” Round,
straight
1 Ft.
x(
) =
Ft.
6” Round,
roof cap
30 Ft.
x(
) =
Ft.
7” Round,
straight
1 Ft.
x(
) =
Ft.
6” round to
3 1/4” x 10”
rect.
transition
1 Ft.
x(
) =
Ft.
3 1/4” x 10”
Rect. 90 0
elbow
15 Ft.
x(
) =
Ft.
16 Ft.
x(
) =
Ft.
3 1/4” x 10”
Rect. 45 0
elbow
9 Ft.
x(
) =
Ft.
6” round to
3 1/4” x 10”
rect.
transition
90 0 elbow
7” Round,
90 0 elbow
15 Ft.
x(
) =
Ft.
3 1/ 4” x 10”
Rect. 90 0
flat elbow
24 Ft.
7” Round,
45 0 elbow
9 Ft.
x(
) =
Ft.
7” Round
30 Ft.
wall cap
with damper
x(
) =
Ft.
7” Round,
roof cap
30 Ft.
x(
) =
Ft.
7” round to
3 1/4” x 10”
rect.
transition
8 Ft.
x(
) =
Ft.
7” round to
3 1/4” x 10”
rect.
transition
90 0 elbow
15 Ft.
x(
) =
Ft.
x(
) =
Ft.
Ft.
3 1/4” x 10”
30 Ft.
Rect.
wall cap
with damper
x(
3 1/4” x 10”
Rect. to
6” round
transition
5 Ft.
x(
) =
Ft.
3 1/ 4” x 10”
Rect. to
6” round
transition
90 0 elbow
15 Ft.
x(
) =
Ft.
6” Round,
90 0 elbow
15 Ft.
x(
) =
Ft.
6” Round,
45 0 elbow
9 Ft.
x(
) =
Ft.
) =
Subtotal column 1 =
Ft.
Maximum Duct Length: For satisfactory air movement,
the total duct length of a 3 1/4” x 10” rectangular, 6” or 7”
diameter round ductshould not exceed 100 equivalent feet.
4
Subtotal column 2 =
Ft.
Subtotal column 1 =
Ft.
Total ductwork
Ft.
=
Min 32"-Max 52"
Maximum mount height should be no higher than 36".
It is important to install the hood at the proper mounting
height. Hoods mounted too low could result in heat
damage and fire hazard; while hoods mounted too high
will be hard to reach and will loose its performance and
efficiency.
14 1/2"
Min 96"-Max 124”
Min 28"-Max 36"
If available, also refer to range manufacturer's height
clearance requirements and recommended hood
mounting height above range. Always check your local
codes for any differences.
36"
*Minimum ceiling height of 96”. Hood
mounted at 28” above cooking surface.
** Maximum ceiling height of 124". Hood
mounted at 36" above cooking surface.
Minimum Duct Size:
DUCTING
Round - 6” minimum at 600 cfm
Round - 10" to 8” minimum at 1000 cfm
Rect angular - 3 1/4” x 10” minimum only if
using internal blower at 600 cfm. Using
rectangular ductwork will require a transition
adapter (not provided, but readily available at
most hardware stores).
A minimum of 6” round or 3-1/4 x 10"
rectangular duct work must be used to maintain
maximum air flow efficiency with the 600 cfm
internal blower. A minimum of 10"to 8” round must be
used with the 1000 cfm external blower.
Always use rigid type metal duct work only.
Flexible ducts could restrict air flow by up
to 50%.
DAMAGE-SHIPMENT / INSTALLATION:
Use calculation worksheet to compute total
duct work.
• Please fully inspect unit for damage
before installation.
ALWAYS, when possible, reduce the number
or transitions and turns. If a reducer is used,
install a long reducer instead of a pancake
reducer. Reduce duct size as far away from
opening as possible.
• If the unit is damaged in shipment , return
the unit to the store in which it was bought
for repair or replacement.
• If the unit is damaged by the customer ,
repair or replacement is the responsibility
of the customer.
If turns or transitions are required:
Install as far away from opening and as far
apart, between 2, as possible.
• If the unit is damaged by the installer (if
other than the customer), repair of replace
ment must be made by arrangement
between customer and installer.
5
Installation - Mounting Height & Clearance
Minimum mount height between range top to hood bottom should be no less than 28".
Installation - Ducting
www.zephyronline.com
WARNING FIRE HAZARD
NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics, or garages. All exhaust must
be ducted to the outside.
Use single wall rigid Metal ductwork only.
Fasten all connections with sheet metal screws and tape all joints w/ certified Silver Tape or DuctTape.
Some Ducting Options:
External
Blower
Roof Pitch w/
Flashing & Cap
side wall
cap with
gravity
damper
Soffit or crawl space
External
Blower
Soffit or crawl space
6
10”
19 3/4”
16 5/8”
13 3/8”
14 1/2”
LOGO CHENG DESIGN BY ZEPHIR
95°
11 7/8”
36”, 42”, 48”
22 5/8”
5" - 36"
8"- 42"
3 1/2"-48"
6"
15”
1/4”
R
5/
16
”
”
/8
7 3/8”
41
O
R 41
1/32”
15 /32”
1“
8 5/16”
9 3/16”
7
Installation - Specifications
19 3/4”
Ins ta lla tion - Interna l B lower
www.zephyronline.com
ATTENTION
The following are intructions for installing internal blower model CBI-600. For instructions on preparing for external
blower model CBE-1000 please turn to page “10”. Before installing, verify that motor spins freely.
The internal blower kit consists of the blower
and capacitor box with wiring.
1. Position blower as shown.
2. Att ach blower to flange as shown using
the provided 1/2” 5x15mm screws with
washers.
3. P osition capacitor box as shown.
4. Secure capacitor bo x to hood using the
provided 1/2” self tapping screws.
8
6. Re-attach grounding screw to finish
installation of capacitor box. Refer to Fig-A on
previous page.
7. Attach short capacitor connector to blower
connector.
8. Att ach long capacitor connector to control
board connector.
9. Use plastic tie to hold wiring together.
10. Remove wood block
Final view of internal blower install.
Continue to page “12” for hood installation instructions.
9
Installation - Internal Blower
5. Remove existing grounding screw and
attach grounding wire from capacitor box.
Ins ta lla tion - P repa ring E xterna l B lower
www.zephyronline.com
ATTENTION
The following are intructions on preparing your hood for installation with external blower model CBE-1000.
For instructions on installing internal blower model CBI-600 please turn to page “8”.
NOTE: Please refer to the CBE-1000 manual for external blower mounting instructions.
The external blower kit consists of an 8”
collar, and external blower wiring box. The
external blower is purchased separately.
1. Remove screws from internal flange.
2. Remove internal flange from hood.
3. Position 8” collar as shown.
4. Att ach 8” collar to hood as shown using
provided 1/2” self t apping screws.
5. Attach external blower wiring box to top of
hood using provided 1/2” self t apping
screws.
10
7. Secure cover to box with provided screw.
8. Attach connector from external blower
wiring box to control board box connector
inside hood.
9. Attach grounding wire from external blower
wiring box to grounding screw of the junction
box. Refer on Fig-A in diagram below .
10. Final view of external blower preparation
Continue to page “12” for hood installation instructions.
For external blower installation please refer to the manual
included with the external blower.
11
Ins ta lla tion - P repa ring E xterna l B lower
6. Position cover onto external blower
wiring box.
www.zephyronline.com
Installation - Preparing Hood
Duct Cover
Ceiling Bracket
C/L
Duct Cover
Ceiling Bracket
B
C
21”
14 1/2”
7 1/2”
A
min 28”
max 36”
C/L
C/L
Attach screws to
ceiling bracket
1. Measure from cooking surface to hood bottom, level and mark line A.
2. Plum and mark center line.
3. Mark mounting height, line B (14 1/2” from line A). This is the top of the hood.
4. Measure up, 7 1/2” from line A and mark mounting spread from C/L Line C. (21”)
5. Follow center line up to the ceiling, measure and mark 6” from the wall. Make sure the spot you mark is still
on the center line. This is where the center of the duct cover ceiling bracket will mount.
6. Place duct cover ceiling bracket onto ceiling and mark the (2) holes where screws will be attached. If attaching
bracket to drywall only, drill and insert provided anchors into the marked holes. Cut out inside diameter of the
ceiling bracket to fit the 6” or 8” round duct work. Attach bracket to ceiling with (2) screws provided.
ELECTR I CAL - WAR NI NG
7. Prepare duct work and electrical.
All Electrical work must be performed by a qualified electrician or person with similiar
technical know and background.
For personal safety, remore house fuse or open circuit beaker before beginning installation.
Do not use extension cords or adapter plug with this appliance.
Follow National Electrical Codes or prevailing local codes and ordinances.
Electrical Supply:
This appliance requires a 120V 60Hz electrical supply, and connected to an individual, properly grounded branch
circuit, protected by a 15 or 20 ampere cicuit breaker or time delay fuse. Wiring must be 2 wire with ground.
Please refer to Electrical Diagram labeled on product.
12
Ins ta lla tion - M ounting Hood
Top
gap between
bracket and
wall
B
C
A
Bottom
Attach screws to both
sides of the duct cove
rs
and secure to ceilingbracket.
10”
Electrical
1. Place wall bracket on line C. Position top of wall bracket so it is even with the 21” mounting spread. Make
sure bracket is attached to wall as shown in the diagram. The top of the wall bracket should have a gap between
it and the wall. The bottom should be flush against the wall. Use (3) 2” wood screws to attach bracket to wall. Use
anchors if not mountingto studs.
2. Lift hood onto wall bracket, there is a lip on the back of the hood which will rest on the wall bracket. Secure in
place by *screwing (2) screws with washers through hood into the wall. There are two holes at the bottom inside
the hood in which to do this.
3. Place telescopic duct covers on top of hood and extend top duct cover to the ceiling bracket. Attach duct cover to
ceiling bracket with the providedscrews.
4. Run duct work down to top of motor. Attach electrical wiring from ceiling to wiring on top of motor housing. (slide
duct cover up towards ceiling to gain access to the motor housing)
* Note:If installing onto drywall only with no wall studs present, attach E Z anchors (not provided) into the wall.
Please see page 15 for external blower installation instructions.
13
Ins ta lla tion - Atta ching Utens il R a il
www.zephyronline.com
Set
screw
Front
Back
1. Attach utensil rail to hood canopy. A small hole has been pre-drilled into the canopy to provide a starting point
to attach the first utensil rail post. After the first post is lined up with the hole, gently slide the rest of the rail onto
the canopy. (note: be careful not to scratch the stainless steel when performing this step, this is why there is a
starter hole).
2. A ttach a short set screw into eac h post in order to hold utensil rail onto canopy.
14
Features & Controls - Touch Controls & Features
www.zephyronline.com
1 Blower On/Off
5 Display (Speed level, Delay Off Indicator, Filter Clean/Change)
6 Mood Light On/Off
2 Adjust 3 Speed Levels
4 Lights On/Off/Hold to Dim
3
15 Min Delay Off
1. Blower On/Off
By pressing
, the blower is switched On and Off.
2. Speed Selection
The 3 speed levels are selected by pressing
The display indicates level selected.
to decrease and
to increase speed level.
3. Delay Off
This is used for programmed shut down of blower and lights 15 minutes after the function is activated.
Press once, a dot flashes in the lower right hand side of display
indicating the function is on.
The hood will completely shut down in 15 minutes.
4. Lights On/Off/Dim
Switch lights On and Off by pressing
once. To dim lights, press
again.
5. Advance Display Functions
6. Mood Light On/Off
This switch turns the mood lights On and Off. Press IN to turn on, press again to turn OFF.
Filters Clean Reminder (Metal):
After every 30 hours of use, the display will start flashing an
filters from residue and possible clogs.
reminding you to clean the baffle
The standard Baffle Filters are required to be cleaned frequently and as recommended in order to maintain
blower efficiency. If improperly maintained, residue from cooking will sift through filters and cause damage to
hood blowers and other sensitive components; and possibly clog duct work and create a fire hazard.
15
Filter Clean Reminder:
When
flashes on display, the baffle
filters installed are required to be cleaned.
This will occur after every 30 hours of use.
Clean Filters
display <A> flashes
Re-setting Function:
Reset the Filter Clean Reminder timer when
filters are cleaned and re-installed (with
hood off). Press and hold
for approx.
5 seconds, the display will appear; hold for
approximately 5 seconds until
on display disappears
. The Filter Clean
Reminder function is now re-set and a new
30 hours elapse cycle is initiated.
To Reset
hold 5 secs.
16
display from <C> to < >
F ea tures & C ontrols - B a ffle F ilters C ha nge Indica tor
Filter Clean Reminder (Standard Baffle Filters fitted):
A set of baffle filters are fitted by the factory. These Baffle Filters are intended to filter out residue from cooking. They
need not be replaced on a regular basis but are required to be kept clean. The Filter Clean Reminder function in
the microprocessor will automatically indicate by a
flashing when the metal filters need to be cleaned after
every 30 hrs. of use. Filters can be cleaned by hand with non-abrasive soap or in a dishwasher.
M a intena nce - C lea ning
www.zephyronline.com
Surface Maintenance:
Clean periodicallywith hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent , or steel
i h will scratch and damage surface.
wool/scouring pads whic
For heavier soil use liquiddegreaser.
After cleaning, you may use non-abrasive stainless steel polish/ cleaners, topolish and buff out the stainless luster
and grain. Always scrub lightlyy with clean cotton cloth, and with the grain.
Do not use any product containing chlorine bleach. Do not use “orange” cleaners.
Baffle Filters
The Metal Filters fitted by the factory are intended
to filter out residue and grease from cooking. They
need not be replaced on a regular basis but are
required to be kept clean.
Filters should be cleaned after every 30 hours of
use. Use the Filter Clean Reminder function on the
controls to determine when filters require cleaning.
12 3/4””
Handles
Remove filter by sliding towards you and
pullingdown (Fig. 1).
Remove and clean by hand or in dishwasher.
Spray degreasing detergent and leave to soak if
heavily soiled.
15”
Dry filters and re-install before using hood.
ReplacingBaffle Filters
Should filters wear out due to age and prolonged
use, contact Zephyr to purchase replacements.
(Fig. 1)
17
CA UTION: Light bulbs become extremely hot when turned on. DO NOT touch bulbs until switched off
and cooled. Touching hot bulbs may cause serious burns.
Make sure all power is turned off and bulbs are not hot.
Remove bulb by pressing both ends of the metal retaining clip together, the light socket will now protude from the hood
allowing you to remove the bulb. (B e careful when releasing retain clip as it is under pressure to hold it in place)
Replacement halogen bulbs are available at most stores which sell light bulbs. Purchase type G U-10, 120 V, 50 W.
Press together
to release clip
HalogenBulb
To replace mood lightingbulb, remove baffle filter from hood. Lift up the metal plate which is inside the hood on the left
and right sides. It is held on with two philips head screws. Unscrew mood lightingbulb counter-clockwise and replace
with a standard 40W, 125V-1 30V mediumbase bulb.
MetalPlate
MoodLightingBulb
18
M a intena nce - Lights
Replacing Light Bulbs:
Trouble S hooting
www.zephyronline.com
Issue
Cause
What to do
After installation, the unit
doesn’t work?
1. The power source is not turned ON.
1. Make sure the circuit breaker and the unit’s
power is ON.
2. The power line and the cable locking connector is
not connecting properly.
2. Check the power connection with the unit is
connected properly.
3. The switch board and control board wirings
are disconnected.
3. Make sure the wirings between the switch
board and control board are connected properly.
4. On the switch board, Black/White wire of White
wire is disconnected.
4. Make sure the Black/White wire or White wire
connects properly.
5. The switch board or control board is defective.
5. Change the switch board or control board.
1. The motor is defective, possible seized.
1. Change the motor.
2. The thermally protected system detects if the motor
is too hot to operate and shuts the motor down.
2. T he motor will function properly after the
thermally protected system cool down.
3. Damaged capacitor.
3. Change the capacitor.
1. The motor is not secure in place.
1. Tighten the motor in place.
2. Damaged blower wheel/makes noise.
2. Change the motor.
3. The hood is not secured in place.
3. Check the installation of the hood.
The motor is working,
but the lights are not.
1. Defective halogen bulb.
1. Change the halogen bulb.
2. The light bulb is loose.
2. Tighten the light bulb.
The hood is not venting
out properly.
1. T he hood might be hanging too high from the
cook top.
1. Adjust the distance between the cook top
and the bottom of the hood within 24” and
32” range.
2. The wind from the opened windows or opened
doors in the surrounding area are affecting the
ventilation of the hood.
2. Close all the windows and doors to eliminate the
outside wind flow.
3. Blocking in the duct opening or ductwork.
3. Remove all the blocking from the duct work or
duct opening.
4. The direction of duct opening is against the wind.
4. Adjust the duct opening direction.
5. Using the wrong size of ducting.
5. Change the ducting to at least 6” or higher
for the internal blower and 8” or higher for the
external blower.
1. Baffle filter is loose.
1. Remove filter and reinstall it or change the
baffle filter.
1. Control board needs to be reset.
1. Turn circuit breaker which controls the hood off
for at least 15 minutes.
Turn it back on and this should fix the problem.
1. Defective control board.
1. Replace control b oard.
Light works, but motor is
not turning.
The unit is vibrating.
Filter is vibrating.
After hood has been
installed for a period of
time, it stopped working.
19
www.zephyronline.com
List of Parts and Accessories
Part Description
Part#
Halogen Bulb G U-10, 120V, 50W
Z0B-0020
Incadescent Bulb T29 127V 40 W
Z0B-0003
Accessory Description
Part#
Internal Blower, 600 cfm
CBI-600
External Blower, 1000 cfm
CBE-1000
Duct Cover Extension Kit
Z1C-00OK
20
Warranty
www.zephyronline.com
TO OBTAIN SERVICE UNDER WARRANTY
or any Service Related Questions, please call:
1-888-880-8368
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
TO OBTAIN SERVICE UNDER WARRANTY: You must present proof of original purchase date.
Please keep a copy of your dated proof of purchase (sales slip) in order to obtain service under warranty.
One Year Service Repair Warranty:
For one year from date of original purchase, we will provide free of charge, service labor to repair any failed parts or
components due to manufacturing defects.
Two Years Parts Warranty:
For two years from date of original purchase, we will provide free of charge, nonconsumable replacement parts or
components that failed due to manufacturing defects. Consumable parts not covered by this warranty include: Light Bulbs,
Metal and Charcoal Filters.
Who is Covered:
This warranty is extended to the original purchaser for products purchased for ordinary home use in the 48 mainland states,
Hawaii and Washington D.C. In Canada and Alaska, this warranty is Limited.
There might be costs associated with
shipping the products to our designated service locations or you might need to pay service technician's travel costs, to have
the appliance repaired in-home.
This Warranty will be Voided when:
Product damaged through negligence, misuse, abuse, accident. Improper installation and failure to follow installation instructions. When product is used commercially or other than its intended purpose. Damaged because of improper connection with
equipment of other manufacturers. Repaired or modified by anyone other than Zephyr's Authorized Agents.
What is Not Covered:
Consumable parts such as light bulbs, filters, and fuses. Services outside of service area and the labor cost incurred in
connection with the removal, shipping and reinstallation cost, nor does it cover any other contingent expenses. The natural
wear of finish, and wear due to improper maintenance, use of corrosive and abrasive cleaning products, pads, and oven
cleaner products. Chips, dents or cracks due to abuse, misuse, freight damage, or improper installation. Service trips to your
home to teach you how to use the product. Damage of product caused by accident, fire, floods or act of God.
This warranty is valid in the United States and Canada. It is non-transferable and applies only to the original purchaser and
does not extend to subsequent owners of this product. Any applicable implied waranties, including the warranty of
merchantability, are limited in duration to a period of express warranty as provided herein beginning with the date of original
purchase at retail and, no warranties, whether express or implied, shall apply to this product thereafter.
Have your product proof of purchase with date ready for warranty issues.
Or write to:
Zephyr Corporation
Service and Warranty Department
395 Mendell Street
San Francisco, CA 94124
JAN07.0101
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement