GE DPGT650EHMG Profile™ 7.1 Cu. Ft. King-size Capacity High-Efficiency Electric Dryer Installation instructions


Add to my manuals
4 Pages

advertisement

GE DPGT650EHMG Profile™ 7.1 Cu. Ft. King-size Capacity High-Efficiency Electric Dryer Installation instructions | Manualzz

DPGT650EH

GE Profile Harmony Dryer

GE Profile ™ High-Efficiency Electric Dryer

Dimensions and Installation Information (in inches)

Exhaust Options: 4-way via rear, right, left and bottom. Dryer is shipped exhausted to the rear. Right, left or bottom exhaust requires a conversion kit.

NEMA Receptable codes:

3-prong dryer cord/30A/4' long (cat #WX9X2) is for NEMA10-30R receptable

4-prong dryer cord/30A/4' long (cat #WX9X18) is for NEMA14-30R receptacle

Circuit Requirements: An individual properlygrounded branch circuit, protected by a 30 amp circuit breaker or a time-delay fuse is required.

Electric Dryer Rating: 240V, 6000W,

28.5A, 60Hz

Note: Dryer wall outlet must be located within

36" of service cord entry and accessible when dryer is mounted in position.

Installation Information: For complete information, see installation instructions packed with your dryer.

22-1/2 29

26-1/2

3-1/2

Side View

36

43

2-1/2

3

13

27

3-1/2

Rear View

For answers to your Monogram, ® GE Profile ™ or

GE ® appliance questions, visit our website at ge.com or call GE Answer Center ® service,

800.626.2000.

Listed by

Underwriters

Laboratories

Specification Revised 5/09 270194

DPGT650EH

GE Profile ™ High-Efficiency Electric Dryer

For complete information, see installation instructions packed with your dryer.

Ducting Materials:

For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit

WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4” diameter can be maintained throughout the entire length of the transition duct. Please see installation instruction packed with your dryer for complete instructions when using flexible metal

(foil type) ducting.

Exhaust Length Calculation:

1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn.

2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.

Dryers must be exhausted to the outside.

Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.

Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be located at least 12" above the ground or any other obstruction with the opening pointed down.

Dryer Elbow Kit, Pub. No. 14-A003 is available at additional cost. For use with side or bottom exhaust options.

For more information on venting kits and accessories, please call 1-800-GE-CARES.

Specification Revised 5/09 270194

DPGT650EH

GE Profile ™ High-Efficiency Electric Dryer

Dimensions and Installation Information (in inches)

Special Installation Requirements

Alcove or Closet Installation:

• If your dryer is approved for installation in an alcove or closet, it will be stated on a label

on the dryer back.

• The dryer MUST be exhausted to the outside.

• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:

0" either side; 3" front and rear

• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.

• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.

• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.

Bathroom or Bedroom Installation:

• The dryer MUST be exhausted to the outdoors.

• The installation must conform with the local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.

Minimum Clearances other than Alcove or Closet Installation:

• Minimum clearances to combustible surfaces are: 0" both sides; 3" rear

Dryer Exhausting Information : Use metal duct only, vertical and horizontal ducting.

A

A

4

Domestic

B dryer models

2-1/2

7.0, 6.0 and 5.8 cu. ft.

capacity models all electric dryers

Number of

90° turns

0

1

2

3

4

Best performance

Maximum length of 4" dia. rigid metal duct

Exhaust hood type

A

4" opening

90 ft.

60 ft.

45 ft.

35 ft.

25 ft.

B

2-1/2" opening

60 ft.

45 ft.

35 ft.

25 ft.

15 ft.

For answers to your Monogram, ® GE Profile ™ or

GE ® appliance questions, visit our website at ge.com or call GE Answer Center ® service,

800.626.2000.

Listed by

Underwriters

Laboratories

Specification Revised 5/09 270194

DPGT650EH

GE Profile ™ High-Efficiency Electric Dryer

Features and Benefits

• 7.1 Cu. Ft. King-Size Capacity - Large enough to handle anything the washer sends its way

• Sensor Dry Plus - Continually monitors moisture levels to help clothes look better longer

• Push Button Controls with LED Countdown Timer - Simplify cycle selection and provide accurate cycle times

• Delicate Cycle with Extra-Low Heat Setting - Maintains an average fabric temperature of 125 degrees F to protect fine handwashables

• Stainless Steel Drum - Resists rust and won't chip, peel or snag clothes

• 5 Heat Selections - Offer enhanced drying performance and fabric care

• Multiple Dry Cycles - Deliver optimal drying results

• Adaptive Cool-down - Tumbles clothes with cool air to reduce wrinkling

• Speed Dry - Delivers ready-to-go results in minutes

• Wrinkle Care Extended Tumble - Continues to tumble clothes without heat to help prevent wrinkling and creasing

• Delay Start - Lets you do the laundry on your terms

• Variable End-Of-Cycle Signal - Adjustable volume offers added flexibility

• Supreme Quiet Sound Package - GE's quietest sound package ever

• Reverse-A-Door - Offers added installation flexibility

• Model DPGT650EHMG –Champagne

• Model DPGT650EHWW –White on white

P

OWER

Very Dry

More Dry

Normal

Less Dry

Damp Dry

High

Medium

Low

Extra low

60 Mins.

50

40

30

20

L

D

RY

EVEL

T

EMP

T IME

DRY

High

Low

Off

S

IGNAL

S

ENSOR

COTTONS ULTRA DELICATES

EASY CARE

ACTIVE

WEAR

DELICATES

M

ANUAL

D

SPEED DRY

DEWRINKLE

AIR DRY

C

YCLES

S

TART

P AUSE

DPGT650EH/GH/WW

Specification Revised 5/09 270194

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement