AGRF1100
PolySwitch®
PTC Devices
PRODUCT: AGRF1100
DOCUMENT: SCD25238
REV LETTER: D
REV DATE: MARCH 12, 2013
PAGE NO.: 1 OF 2
Overcurrent Protection Device
Specification Status: Released
Electrical Rating
Voltage:
16VDC MAX
Insulating Material:
Cured, Flame Retardant Epoxy Polymer
Lead Material:
20 AWG Tin Plated Copper
(0.8 mm [0.032] nom. diameter)
Part Marking:
Manufacturer’s Mark
G11
and Part Identification
Lot Identification
TABLE I. INSTALLATION ENVELOPE DIMENSIONS:
mm:
in*:
A
B
MIN
MAX
MIN
MAX
-17.5
-26.5
-(0.69)
-(1.04)
*Rounded off approximation
C
MIN
4.3
(0.17)
D
MAX
5.8
(0.23)
MIN
7.6
(0.30)
E
MAX
---
MIN
---
MAX
3.0
(0.12)
F
TYP
1.2
(0.05)
G
MIN
MAX
-7.47
-(0.294)
TABLE II. PERFORMANCE RATINGS:
CURRENT RATINGS
TIME TO
TRIP
INITIAL
RESISTANCE
AMPS
AT 25°C
HOLD HOLD TRIP
AT
AT
R1 MAX RA MAX
11.0
10.5
20.3
SECONDS
AT 25°C, 55 A
MAX
OHMS
AT 25°C
MIN
MAX
Reference Documents:
Precedence:
Effectivity:
CAUTION:
7.5
0.0033
0.0060
R1 MAX
1 HR. POST TRIP
RESISTANCE
STANDARD TRIP
OHMS
AT 25°C
RA MAX
OHMS
AT 25°C
0.0089
0.0093
TRIPPEDSTATE
POWER
DISSIPATION
WATTS AT
25°C
TYP
3.7
PS400, PS300 (reference for R1 MAX)
This specification takes precedence over documents referenced herein.
Reference documents shall be the issue in effect on the date of invitation for bid.
Operation beyond the rated voltage or current may result in rupture, electrical arcing or flame.
Materials Information
ROHS Compliant
ELV Compliant
Pb-Free
Halogen Free*
HF
* Halogen Free refers to: Br≤900ppm, Cl≤900ppm, Br+Cl≤1500ppm.
PolySwitch®
PTC Devices
Overcurrent Protection Device
PRODUCT: AGRF1100
DOCUMENT: SCD25238
REV LETTER: D
REV DATE: MARCH 12, 2013
PAGE NO.: 2 OF 2
TABLE III. AUTOMOTIVE SPECIFIC STRESS TESTS AND TEST CONDITIONS:
ELECTRICAL STRESS TESTS
TEST CONDITIONS (see note 2)
ESD Voltage Withstand
(see note 1)
Short Circuit Fault Current Durability
25kV
Fault Current Durability
350 cycles, 16V/100A
End-of-life Mode Verification
1750 cycles, 16V/100A
Jump Start Endurance
(see note 1)
Load Dump Endurance
(see note 1)
3 cycles, 26V, 1 minute duration
25 cycles, 16V, 200A
10 cycles, 86.5V
Note 1: The PolySwitch devices are tested in series with a load resistance and the voltages specified in the test conditions are
shared between the PolySwitch device and the load resistance as specified in PS400.
Note 2: Please refer to Appendix A of PS400 for the detailed test procedures
© 2004, 2013 Tyco Electronics Corporation, a TE Connectivity Ltd. Company. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement