null  null
Paintable Mist
NP-121
5/21/12
Total pages: Page 1 of 6
MATERIAL SAFETY DATA SHEET
1. Product and Company Identification
Product Name: Paintable Mist
Product Code: NP-121
Product Use: Mold Release
Product Type: Aerosol
Manufacturer Plastic Process Equipment, Inc.
Revision Date 5/21/12
8303 Corporate Park Drive
Address
Macedonia, OH 44067
800 535 5053
EMERGENCY:
216-367-7000
NOTE: The information contained herein is accurate to the best of our knowledge. We do not suggest or
guarantee that any hazards listed herein are the only ones which exist. PPE provides this information
as guidance for providing personal protection to your employees. The user has the sole responsibility to
determine the suitability of the materials for any use and the manner of use contemplated. The user must
meet all applicable safety and health standards. PPE provides this information as guidance for
providing personal protection to your employees.
2. Composition / Information on Ingredients
Ingredients
CAS #
Percent
Exposure Limits
Trichloroethylene
79-01-6
60-70%
OSHA (TWA)
ACGIH (TWA)
1,1,1,2-Tetrafluoroethane (134a)
811-97-2
35-40 %
OSHA (TLV)
100 ppm
25 ppm
1000 ppm
3. Hazards Identification
CAUTION!
DANGER:
CONTENTS UNDER PRESSURE
POISON.
Odor/Appearance: Clear mist as dispensed from aerosol can.
Potential health effects
Routes of exposure:
Skin, eyes, inhalation, ingestion.
Eye Contact:
May cause immediate or delayed irritation. Irritation may show up as redness and/or swelling.
May cause corneal damage.
Skin Contact:
Repeated or prolonged contact with skin may produce redness, irritation and/or dryness. May
cause or aggravate dermatitis or other existing skin condition.
1
Paintable Mist
NP-121
5/21/12
Total pages: Page 2 of 6
Inhalation:
Breathing of vapor or mist is possible. Breathing small amounts of this material
during normal handling is not likely to cause harmful effects. Breathing large amounts
may be harmful. Symptoms are not expected at air concentrations below the
recommended exposure limits, if applicable (see Section 8.). Alcohol consumed before or
after exposure may worsen harmful effects
Ingestion:
Swallowing small amounts of this material during normal handling is not likely to
cause harmful effects. Swallowing large amounts may be harmful. This material can get
into the lungs during swallowing or vomiting. This results in lung inflammation and
other lung injury..
Signs or Overexposure:
Signs and symptoms of exposure to this material through breathing, swallowing,
and/or passage of the material through the skin may include:, stomach or intestinal upset
(nausea, vomiting, diarrhea), irritation (nose, throat, airways), cough, central nervous
system depression (dizziness, drowsiness, weakness, fatigue, nausea, headache,
unconsciousness), weakness, lack of coordination, irregular heartbeat, and death
Target Organs:
Persons exposed to trichloroethylene may become intolerant to alcohol with small
quantities causing drunkenness and skin blotches., Studies on trichloroethylene-exposed
workers indicate that overexposure to this chemical may result in involuntary eye
movement, tremors, sleep disturbances, symptoms of central nervous system(CNS)
depression (dizziness, drowsiness, weakness, fatigue, nausea, headache,
unconsciousness), and other CNS effects., Brief or prolonged exposure to
trichloroethylene and its decomposition products (e.g. dichloroacetylene) has been
associated with cranial neuropathy (characterized by facial numbness), although it isn't
clear which agent is responsible for the effect., Overexposure to this material (or its
components) has been suggested as a cause of the following effects in laboratory
animals:, mild, reversible liver effects, effects on hearing, kidney damage.
4. First Aid Measures
Eye Contact:
Flush with warm water for 15 minutes. Seek medical attention.
Skin Contact:
Wash with soap and water. Remove any contaminated clothing and launder before reusing. If
irritation persists, seek medical attention.
Inhalation:
Remove exposed individual to fresh air, protecting yourself. Restore breathing if necessary.
Contact a physician.
Ingestion:
Seek medical attention. If individual is drowsy or unconscious, do not give
anything by mouth; place individual on the left side with the head down. Contact a
physician, medical facility, or poison control center for advice about whether to induce
vomiting. If possible, do not leave individual unattended.
2
Paintable Mist
NP-121
5/21/2012
Total pages: Page 3 of 6
5. Fire Fighting Measures
Flash Point: None
Flammable limits in air, % by volume:
Upper:
No Information
Lower:
No Information
Extinguishing Media:
Dry chemical, carbon dioxide, halon, or foam is recommended. Water spray may be used to cool containers
or structures. Halon may decompose into toxic materials and carbon dioxide will displace oxygen, take
proper precautions when using these materials.
Unusual Fire & Explosion Hazards:
This material may be ignited by extreme heat, sparks, flames or other ignition sources (static electricity).
Vapors are heavier than air and will collect in low areas (sewers) or travel considerable distances. If
containers are not cooled in a fire, they may rupture and ignite.
Special Fire Fighting Procedures:
At elevated temperatures (over 130F) aerosol container may burst, vent or rupture; use equipment or
shielding to protect personnel. Cooling exposed containers with streams of water may be helpful.
Emergency responders should wear self-contained breathing apparatus. Wear other protective gear as
conditions warrant. Keep unauthorized people out and try to contain spills or leaks if it can be done safely.
Material will float on water, avoid spreading the fire.
6. Accidental Release Measures
Spill or Leak Instructions
Contain spill with dikes of soil or nonflammable absorbent to minimize contaminated area. Avoid run-off
into storm sewers and ditches leading to waterways. If required, notify state and local authorities. Place
leaking containers in well-ventilated area. Clean up small spills by using a nonflammable absorbent or
flushing sparingly with water. Contain larger spills with nonflammable diking or absorbent. Clean up by
vacuuming or sweeping.
Keep unnecessary people away; isolate hazard area and deny entry. Stay upwind; keep out of low areas.
Assess the spill situation, as the spill may not evolve large amounts of hazardous airborne contaminants in
many outdoor spill situations. It may be advisable in some cases to simply monitor the situation until
spilled product is removed.
7. Handling and Storage
Handling:
Store below 120°F in cool, dry area, out of direct sunlight and away from strong oxidizers. Do not
puncture or burst. Use in accordance with good work place practices. Use with adequate ventilation. Keep
containers closed when not in use. Always open containers slowly to allow any excess pressure to vent.
Avoid breathing vapor. Avoid contact with eyes, skin or clothing. Wash thoroughly with soap and water
after handling. Decontaminate soiled clothing thoroughly before re-use. Destroy contaminated leather
clothing.
3
Paintable Mist
NP-121
5/21/2012
Total pages: Page 4 of 6
Empty containers may contain residues from the product. Treat empty containers with the same precautions
as the material last contained. Do not cut, weld or apply heat to empty containers Do not incinerate
Storage:
Store in a cool, dry area, away form heat or direct sunlight. Keep containers closed when not in use. Do not
store with incompatible materials
8. Exposure Controls / Personal Protection
Protective Equipment:
Use synthetic gloves if necessary to prevent excessive skin contact. Do not wear contacts and
always use ANSI approved safety glasses or splash shield.
Engineering Controls:
General or dilution ventilation is frequently sufficient as the sole means of controlling employee
exposure. Local ventilation is usually preferred. Use a NIOSH approved respirator if ventilation is
not adequate to maintain exposures below TLV levels.
Respiratory Protection:
Use adequate ventilation to maintain exposure limits. If the exposure limits of the products or
any of its components is exceeded, an approved organic vapor mask should be used (consult your
safety equipment supplier). Above exposure limits an approved self-contained breathing
apparatus or airline respirator with full face-piece is required
Other Suggested Equipment:
Eye wash station and emergency showers should be available. Spill containment equipment should
be available.
Discretion Advised:
Eveready. takes no responsibility for determining what measures are required for personal
protection in any specific application. The general information should be used with discretion.
Exposure guidelines:
Ingredients
CAS #
Percent
Exposure Limits
Trichloroethylene
79-01-6
60-70%
OSHA (TWA)
ACGIH (TWA)
1,1,1,2-Tetrafluoroethane (134a)
811-97-2
35-40 %
OSHA (TLV)
1000 ppm
9. Physical and Chemical Properties
Boiling Point: NA
Specific Gravity: >1
Vapor Density: >1(Air=1)
Water Solubility: Negligible
Odor/Appearance: Cleat mist as dispensed from aerosol can.
Odor of chloroform
Evaporation Rate: Ether = 1 Slower
Volatile Organic Compounds:
wt %: 66.32
g/L: 900.23
4
lbs/Gal. 7.51
100 ppm
25 ppm
Paintable Mist
NP-121
5/21/2012
Total pages: Page 5 of 6
10. Stability and Reactivity
Stability: Stable
Conditions to Avoid: Heat, spark, and open flame
Incompatibility: Strong-Oxidizing Agents
Hazardous Decomposition May form carbon dioxide and carbon monoxide, chlorine, hydrogen chloride,
Phosgene, hydrocarbons.
Hazardous Polymerization: Will not occur
11. Toxicological Information
Component Toxicological Information:
Acute oral toxicity
TRICHLOROETHYLENE LD 50 Rat: 4,920 mg/kg
Acute inhalation toxicity
TRICHLOROETHYLENE LC 50 Rat: 12000 ppm, 4 h
Acute dermal toxicity
TRICHLOROETHYLENE LD 50 Rabbit: > 20 g/kg
12. Ecological Information
N/A
13. Disposal Considerations
Do not puncture or burn containers. Give empty, leaking, or full containers to disposal service equipped to
handle and dispose of aerosol (pressurized) containers. Dispose of spilled material in accordance with state
and local regulations for waste that is non-hazardous by Federal definition. Note that this information
applies to the material as manufactured; processing, use, or contamination may make this information
inappropriate, inaccurate, or incomplete.
Note that this handling and disposal information may also apply to empty containers, liners and rinsate.
State or local regulations or restrictions are complex and may differ from federal regulations. This
information is intended as an aid to proper handling and disposal; the final responsibility for handling and
disposal is with the owner of the waste. See Section 9 - Physical and Chemical Properties.
14. Transport Information
Ground (US DOT) Consumer Commodity
Class ORM-D, ERG 126
Or
5
Paintable Mist
NP-121
5/21/2012
Total pages: Page 6 of 6
Aerosols (limited quantity),
Class 2.2, ERG 126
AIR (IATA)
Aerosols (limited quantity),
Class 2.1, ERG 126, UN No. 1950
Vessel
Aerosol (Limited Quantity), Class 2.1, UN No 1950
15. Regulatory Information
Environmental Regulations
SARA 302/304:
None
SARA 311/312:
Immediate ( x )
Delayed (
) Fire ( x ) Reactive ( ) Sudden Release of Pressure ( x )
Section 313
This product contains:
Trichloroethylene `
76-01-6
48-55%
California Prop. 65
WARNING: This product contains a chemical known in the State of California to cause cancer (Trichloroethylene).
All the chemicals used in this product are TSCA listed.
Check with your local regulators to be sure all local regulations are met.
16. Other Information
Hazard ratings This information is intended solely for the use of individuals trained in the NFPA and/or
HMIS systems.
NFPA: Level 1 Aerosol
HMIS: Health: 2 Flammability: 2 Reactivity: 0
RATING: 4-EXTREME
3-HIGH
2-MODERATE 1-SLIGHT 0-INSIGNIFICANT
Note:
For industrial use only. The information contained herein is accurate to the best of our knowledge. We do
not suggest or guarantee that any hazards listed herein are the only ones which exist. PPE makes no
warranty of any kind, express or implied, concerning the safe use of this material in your process or in
combination with other substances. Effects can be aggravated by other materials and/or this material may
aggravate or add to the effects of other materials. This material may be released from gas, liquid, or solid
materials made directly or indirectly from it. User has the sole responsibility to determine the suitability of
the materials for any use and the manner of use contemplated. User must meet all applicable safety and
health standards. Possession of an MSDS does not indicate that the possessor of the MSDS was a
purchaser or user of the subject product.
6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement