Tarmac Slip-On (2013
Installation Instructions
1.
Make sure the bike is completely cool before starting the
installation. Make sure the bike is secure on a centerstand or
ideally a service lift.
2.
Loosen OEM muffler clamp.
Honda
CBR500R
7.
Tighten barrel clamp at header connection.
8.
Before you run the bike, clean off all fingerprints and dirt, as
any oily residue will etch the metal and become somewhat
permanent when the system gets hot. Run the bike and
enjoy. It is normal for some white smoke to appear the first
time you start the bike. This is packing/manufacturing oil from
inside the pipe burning off. Check for gaps or leaks. If you find
a leak, a little high temperature silicon sealant should fix it.
After 50 to 100 miles, recheck all fasteners for tightness.
V.A.L.E.™ Slip-on Exhaust System with M-2 Exhaust Canister
Part # 005-3950405-T
3.
Remove OEM muffler mounting hardware.
4.
Remove OEM muffler assembly. OEM gasket will not be used
with TBR exhaust.
5.
Apply a thin layer of anti-seize to TBR slip tube outlet and
connect to Tarmac muffler using supplied hook springs.
Loosely install barrel clamp onto slip tube inlet.
6.
Install TBR slip-on assembly onto stock header and attach
muffler bracket to passenger peg mount using supplied bolt,
washer, and nut. Tighten to snug.
IMPORTANT - PLEASE READ CAREFULLY
Two Brothers Racing products are intended for closed course competition
purposes only.
We recommend that this performance part be installed by a qualified motorcycle
technician. If you have any doubts as to your ability to install this performance
part, please consult with your local motorcycle dealer. Read all instructions
first before starting installation. Make sure the motorcycle and exhaust system
are completely cool before starting the installation. Also, make sure the bike is
secure on a centerstand or ideally a service lift during installation. Be sure to save
all stock components for possible use later.
Honda
CBR500R
V.A.L.E.™ Slip-on Exhaust System with M-2 Exhaust Canister
Part # 005-3950405-T
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is completely cool before maintenance.
Qty. Description
Part Number
1
1
1
2
1
1
1
1
1
005-305-10
005-39504S
005-27-59MSH
005-S45
005-W08
005-FN8
005-SH855
005-SP
031-P09175
Tarmac Muffler Canister
Slip-Tube
Clamp
Springs
Washer
Flange Nut
Socket Head Cap Screw
Spring Puller
Anti-Seize
Stainless Header System: Polished stainless steel pipes will turn a light golden hue after a few heat cycles, this is a normal characteristic of high quality stainless steel. Clean using
a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Titanium Header System: Polished titanium pipes will experience color shift ranging from deep blue/purple through amber after a few heat cycles. This is a normal characteristic of
high quality titanium. Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the bright finish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside is in
good condition and not burned out, as exhaust heat inside an empty canister will deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include everything you need to easily do it yourself.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside is in
good condition and not burned out, as exhaust heat inside an empty canister will deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include everything you need to easily do it yourself.
Repack all road canisters every 3,000 miles. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the intense heat and lack of cooling air can quickly burn through the canister material. Two Brothers
Racing does not provide a warranty for burned canisters.
Warranty Information
Two Brothers Racing products are intended for closed course competition purposes only, and therefore are sold “as is” without warranty. Two Brothers Racing specifically disclaims
any warranties of merchantability or fitness for a particular purpose and disclaims all responsibility for consequential and incidental damages or any other losses arising from the use
of these products or parts. Not tested for use with OEM or aftermarket accessories.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement