Linear AM-RRR Installation guide

Linear AM-RRR Installation guide
INTRODUCTION
1. TYPICAL INSTALLATION
The AM-RRR remote radio receiver is designed for use with Linear’s AE1000Plus,
AE2000Plus, and AM3Plus access control systems. The AM-RRR functions as
a remote device that extends the radio range control or supplies localized radio
reception for the controller.
Three antenna types can be used with this receiver. The cabinet mounted type
“F” connector is for connection to the antenna. The local whip antenna (supplied)
screws directly on to the receiver’s connector. The directional (EXA-2000) and omnidirectional (EXA-1000) remote antennas wire to the receiver’s antenna connector with
type RG-59 cable.
PRINTER’S INSTRUCTIONS:
INSTR, INSTL, AM-RRR- LINEAR P/N: 212045 C - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - SIDE 1 OF 2
AM-RRR
Remote
Radio
Receiver
An on-board RADIO RANGE knob allows adjustment of the receiver’s gain. It can be
set to limit the maximum radio range that the receiver can achieve. Two indicators
display the receivers performance and operation. The two color red/green STATUS
indicator lights red when the receiver is getting DC power and turns green when
access is granted to a transmitter. The RADIO indicator lights when the receiver
detects a radio signal. It can be used for trouble shooting and verifying system
performance. Receiver test points are provided for listening to the incoming signals.
Installation
Instructions
The AM-RRR remote radio receiver connects to the controller control unit through a
six-wire cable. A rotary switch in the AM-RRR selects the PBUS device address for
the receiver. Each PBUS device connected to the controller must be set to a different
PBUS device address. Power is supplied to the receiver from the PBUS controller.
AM-RRR MOUNTED
OUTSIDE BUILDING
HOMERUN
WIRE EACH
AM-RRR TO
THE CONTROLLER
EACH AM-RRR EQUALS 4 LOAD UNITS
CABLE LENGTH FORMULA FOR EACH AM-RRR USED IN SYSTEM
CABLE RUN
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340
www.linearcorp.com
2. OPEN CASE
The receiver is housed in a weather-resistant enclosure and can be mounted indoors
or outdoors. Gaskets and a weather-tight wiring strain relief seal the unit from the
elements.
3. LOCATE COMPONENTS
RADIO
RANGE
KNOB
OPEN CASE FROM
ANTENNA END
BOARD SLIDES OUT
FROM 3RD SLOT UP
INSIDE CASE
REMOVE FOUR
SCREWS AND WASHERS
BELDEN 9931 (24 AWG)
FEET x LOAD UNITS < 3,000 MAXIMUM
500 FEET MAXIMUM
WEICO 9405 (20 AWG)
FEET x LOAD UNITS < 10,000 MAXIMUM
SET DEVICE
ADDRESS
SELECTOR
PBUS
DEVICE
ADDRESS
SELECTOR
RADIO
INDICATOR
300 FEET MAXIMUM
ANTENNA
CONNECTOR
(HIDDEN)
GND
AUDIO
FORMULA
4. SET PBUS DEVICE ADDRESS
CLOCKWISE
FOR MAXIMUM
RANGE
RADIO
TEST
POINTS
CABLE TYPE
POWER & DATA
TERMINALS
STATUS
(CONNECTS TO AM/II)
INDICATOR
RED = POWER
GREEN = ACCESS
SET TO POSITION 1-6
(MUST BE DIFFERENT
FROM ALL OTHER
PBUS DEVICES)
5. CONNECT AM-RRR TO CONTROLLER
PRINTER’S INSTRUCTIONS:
INSTR, INSTL, AM-RRR - LINEAR P/N: 212045 C - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - SIDE 2 OF 2
PWR
GND
AM-RRR DAT1
TERMINALS DAT0
DVAL
PCLK
INDICATOR
VIEWING
WINDOW
PWR
GND
DAT1
DAT0
DVAL
PCLK
6. CLOSE CASE AND MOUNT UNIT
7. INSTALL ANTENNA
SECURE CASE
WITH FOUR
SCREWS AND
WASHERS
ACCESS CONTROL
SYSTEM PBUS
TERMINALS
CHOOSE AN ANTENNA TO FIT THE INSTALLATION REQUIREMENTS
OMNI-DIRECTIONAL
EXA-1000 ANTENNA
MOUNTED ON POLE
DIRECTIONAL
EXA-2000 ANTENNA
MOUNTED ON POST
TIGHTEN
AFTER
INSTALLATION
WIRING
STRAIN
RELIEF
LOCAL WHIP
ANTENNA
(SUPPLIED)
CONNECTED
DIRECTLY TO
RECEIVER
SLIDE BOARD INTO
3RD SLOT UP
SCREW CONNECTOR
ONTO RECEIVER
ATTACH CASE TO
MOUNTING SURFACE
ROUTE WIRE THROUGH
STRAIN RELIEF BEFORE
WIRING TO TERMINALS
(TIGHTEN LATER)
CONNECT WIRES TO
AM-RRR TERMINALS
8. PROGRAM SYSTEM
USE SCREW ANCHORS
OR APPROPRIATE HARDWARE
FOR MOUNTING
FOLLOW EXA ANTENNA
INSTRUCTIONS WHEN
CONSTRUCTING ANTENNA
9. TEST SYSTEM
PROGRAM THE CONTROLLER
TO CONFIGURE THE PBUS
DEVICE
LINEAR LIMITED WARRANTY
TEST TRANSMITTERS FROM VARIOUS
LOCATIONS TO DETERMINE RADIO RANGE
ADJUST THE INTERNAL RADIO RANGE
KNOB TO LIMIT RADIO RECEPTION
IF REQUIRED
RECEPTION PATTERN WILL VARY
DEPENDING ON ANTENNA USED
AND SUROUNDING STRUCTURES
RADIO INDICATOR WILL
FLICKER AS SIGNAL IS
RECEIVED
STATUS INDICATOR WILL
LIGHT RED WHEN POWER
IS APPLIED AND GREEN WHEN
ACCESS IS GRANTED
REFER TO THE CONTROLLER
PROGRAMMING INSTRUCTIONS
FOR DETAILS
This Linear product is warranted against defects in material and workmanship for
twelve (12) months. This warranty extends only to wholesale customers who
buy direct from Linear or through Linear’s normal distribution channels. Linear
does not warrant this product to consumers. Consumers should inquire from
their selling dealer as to the nature of the dealer’s warranty, if any. There are
no obligations or liabilities on the part of Linear LLC for consequential
damages arising out of or in connection with use or performance of
this product or other indirect damages with respect to loss of property,
revenue, or profit, or cost of removal, installation, or reinstallation.
All implied warranties, including implied warranties for merchantability and
implied warranties for fitness, are valid only until the warranty expires. This
Linear LLC Warranty is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return Product Authorization
Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an
RPA# and other important details
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fill an important
need in portable wireless signalling. However, there are some limitations which
must be observed.
* For U.S. installations only: The radios are required to comply with FCC Rules and Regulations
as Part 15 devices. As such, they have limited transmitter power and therefore limited range.
* A receiver cannot respond to more than one transmitted signal at a time and may be blocked by
radio signals that occur on or near their operating frequencies, regardless of code settings.
* Changes or modifications to the device may void FCC compliance.
* Infrequently used radio links should be tested regularly to protect against undetected
interference or fault.
* A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale
distributor or dealer, and these facts should be communicated to the ultimate users.
Copyright © 2012 Linear LLC
212045 C
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement