GTO/PRO SW-2500 Single Gate Opener

GTO/PRO SW-2500 Single Gate Opener
Installation Manual for the
Automatic Gate Operator
LI
US
STED
WARNING!
This equipment is similar to other gate or door equipment and meets or exceeds
Underwriters Laboratory Standard 325 (UL 325). However, gate equipment has
hazards associated with its use and therefore by installing this product the
installer and user accept full responsibility for following and noting the installation
and safety instructions. Failure to follow installation and safety instructions can
result in hazards developing due to improper assembly. You agree to properly
install this product and that if you fail to do so GTO, Inc. shall in no event be
liable for direct, indirect, incidental, special or consequential damages or loss of
profits whether based in contract tort or any other legal theory during the course
of the warranty or at any time thereafter. The installer and/or user agree to
assume responsibility for all liability and use of this product releasing GTO, Inc.
from any and all liability. If you are not in agreement with this disclaimer or do
not feel capable of properly following all installation and safety instructions you
may return this product for full replacement value.
READ ALL INSTRUCTIONS CAREFULLY AND COMPLETELY before
attempting to install and use this automatic gate opener. This gate opener
produces a high level of force. Stay clear of the unit while it is operating and
exercise caution at all times.
All automatic gate operators are intended for use on vehicular gates only and
should never be used by pedestrians.
rev - 03/29/06
GTO/PRO • 3121 Hartsfield Road • Tallahassee, Florida, USA 32303
Telephone GTO/PRO Sales: 1-800-543-GATE (4283) or (850) 575-0176 • Fax (850) 575-8912
or GTO/PRO Technical Service: 1-800-543-1236 or (850) 575-4144 • Fax (850)575-8950
www.gtopro.com
R2500INST
This product meets and exceeds the requirements of UL 325, the standard which regulates gate opener safety,
as established and made effective March 1, 2000, by Underwriters Laboratories Inc.
©2005 GTO, Inc.
The GTO/PRO SW-2500 Gate Opener is intended for use with vehicular swing gates. The opener can be used in
Class I, Class II, Class III and Class IV applications.
VEHICULAR GATE OPENER CLASS CATEGORIES
Residential Vehicular Gate Opener-Class I: A vehicular gate opener (or system) intended for use in a home of
one-to-four single family dwelling, or a garage or parking area associated therewith.
Commercial/General Access Vehicular Gate Opener-Class II: A vehicular gate opener (or system) intended for
use in a commercial location or building such as a multifamily housing unit (five or more single family units),
hotel, garages, retail store, or other building servicing the general public.
Industrial/Limited Access Vehicular Gate Opener–Class III: A vehicular gate opener (or system) intended for
use in an industrial location or building such as a factory or loading dock area or other locations not intended to
service the general public.
Restricted Access Vehicular Gate Opener–Class IV: A vehicular gate opener (or system) intended for use in a
guarded industrial location or building such as an airport security area or other restricted access locations not
servicing the general public, in which unauthorized access is prevented via supervision by security personnel.
Conversion Chart
Converting Metric Units to English Equivalents
When You Know
Multiply By
To Find
Symbol
centimeters
meters
kilograms
0.3937
3.2808
2.2046
inches
feet
pounds
in. (or ")
ft. (or ')
lb. (or #)
Converting English Units to Metric Equivalents
When You Know
Multiply By
To Find
Symbol
inches
feet
pounds
2.5400
0.3048
0.4535
centimeters
meters
kilograms
cm
m
kg
Converting Temperature
deg. Celsius
deg. Fahrenheit
(ºC x 1.8) + 32 deg. Fahrenheit
(ºF-32) ÷ 1.8
deg. Celsius
ºF
ºC
FOR YOUR RECORDS
Please record the product serial number (located on the control box cover), and the date
and place of purchase in the spaces provided below. Refer to this information when
calling GTO/PRO for service or assistance with your automatic gate opener.
Serial Number ____________________ Date of Purchase ____________________
Place of Purchase ____________________
Remember to keep all receipts for proof of purchase.
Table of Contents
Gate Opener Class Categories ------------------------------------------------------------- inside cover
Units and Standards Conversion Chart --------------------------------------------------- inside cover
PLEASE READ THIS FIRST! ------------------------------------------------- page iii
Important Safety Instructions -------------------------------------------------- page 1
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
Disconnecting the Opener ------------------------------------------------------------- page 1
Important Safety Instructions for the Consumer ----------------------------------- page 2
Secondary Means of Protection Against Entrapment ----------------------------- page 5
Required Safety Precautions for Gates ---------------------------------------------- page 6
Warning Signs and Labels ------------------------------------------------------------ page 7
Installation -------------------------------------------------------------------------- page 8
Parts List ---------------------------------------------------------------------------------page 8
Technical Specifications -------------------------------------------------------------- page 10
Installation Overview ---------------------------------------------------------------- page 11
Installation of the Mounting Hardware ---------------------------------------------- page 12
Mounting the Opener ------------------------------------------------------------------ page 16
Installation of the Closed Position Stop --------------------------------------------- page 16
Mounting the Control Box ------------------------------------------------------------ page 17
Connecting the Power Cable ---------------------------------------------------------- page 18
Powering the System ------------------------------------------------------------- page 19
Solar Chart ------------------------------------------------------------------------------page 19
Connecting the Transformer ---------------------------------------------------------- page 21
Control Board Settings----------------------------------------------------------- page 22
DIP Switches ----------------------------------------------------------------------------page 22
Setting the Closed Position ----------------------------------------------------------- page 23
Obstuction Sensitivity ----------------------------------------------------------------- page 24
Setting Your Personal Transmitter Code ------------------------------------ page 25
Installing the Receiver ----------------------------------------------------------- page 26
Connecting Additional Safety Devices ---------------------------------------- page 27
Connecting Accessories ---------------------------------------------------------- page 29
Push to Open Installation ------------------------------------------------------- page 30
Maintenance & Troubleshooting Guide -------------------------------------- page 33
Repair Service --------------------------------------------------------------------- page 35
Column Installation Information ---------------------------------------------- page 36
Accessory Catalog ----------------------------------------------------------------- page 37
PLEASE READ THIS FIRST!
Thank you for purchasing a GTO/PRO-SW2500 When correctly installed and properly used, your GTO/PROSW2500 Operator will give you many years of reliable service. Please read the following information to ensure you
have the correct system for your particular needs. This manual will enable you to properly install your GTO/PROSW2500 Automatic Gate Operator.
The GTO/PRO-SW2500 Operator is designed for installation on a pull-to-open single leaf gate (gates that open
into the property). By purchasing an accessory bracket, the GTO/PRO-SW2500 Operator can accommodate a pushto-open single leaf gate (gates that open out from the property). The gate must not exceed 16 feet in length (per leaf)
nor weigh more than 500 pounds (per leaf) (please see Technical Specifications on page 10). The GTO/PROSW2500 Operator can be used on vinyl, aluminum, chain link, farm tube, and wrought iron gates. Use on solid
(wood) gates is not recommended. Solid surface gates have a high resistance to the wind. If the wind is strong enough,
the operator will obstruct and stop.
The GTO/PRO-SW2500 Operator accommodates extra transmitters, digital keypads, solar panels, push buttons,
automatic gate locks, and other access control products. These optional accessories (see the enclosed GTO/PRO®
Accessory Catalog) are available.
The GTO/PRO-SW2500 Operator features adjustable obstruction sensing. This safety feature makes the gate stop
and reverse direction within 2 seconds when it comes in contact with an obstruction. MIN is the factory setting;
meaning the gate will exert the minimum force on an obstruction before it stops and reverses direction.
The GTO/PRO-SW2500 Operator also has an adjustable auto-close feature. After the gate reaches the fully open
position, it can be set to remain open up to 120 seconds before automatically closing. Pressing the transmitter button
at any time after the gate opens fully will cause it to close immediately. OFF is the factory setting; meaning the gate
will stay open until you press the transmitter (or keypad, etc.) again.
Please call GTO/PRO at (800) 543-GATE [4283] or (850) 575-0176 for more information about our GTO/PRO®
professional line of gate operators and accessories. Our Sales Department will be glad to give you the name and phone
number of a GTO/PRO® dealer near you.
iii
IMPORTANT SAFETY INSTRUCTIONS
Because automatic gate openers produce high levels of force, consumers need to know the potential hazards associated with
improperly designed, installed, and maintained automated gate opener systems. Keep in mind that the gate opener is just
one component of the total gate operating system. Each component must work in unison to provide the consumer with
convenience, security, and safety.
This manual contains various safety precautions and warnings for the consumer. Because there are many possible
applications of the gate opener, the safety precautions and warnings contained in this manual cannot be completely
exhaustive in nature. They do, however, provide an overview of the safe design, installation, and use of this product.
CAREFULLY READ AND FOLLOW ALL SAFETY PRECAUTIONS, WARNINGS, AND INSTALLATION
INSTRUCTIONS TO ENSURE THE SAFE SYSTEM DESIGN, INSTALLATION, AND USE OF THIS PRODUCT.
Installation Manual for the
Automatic Gate Operator
WARNING!
This equipment is similar to other gate or door equipment and meets or exceeds
Underwriters Laboratory Standard 325 (UL 325). However, gate equipment has
hazards associated with its use and therefore by installing this product the
installer and user accept full responsibility for following and noting the installation
and safety instructions. Failure to follow installation and safety instructions can
result in hazards developing due to improper assembly. You agree to properly
install this product and that if you fail to do so GTO, Inc. shall in no event be
liable for direct, indirect, incidental, special or consequential damages or loss of
profits whether based in contract tort or any other legal theory during the course
of the warranty or at any time thereafter. The installer and/or user agree to
assume responsibility for all liability and use of this product releasing GTO, Inc.
from any and all liability. If you are not in agreement with this disclaimer or do
not feel capable of properly following all installation and safety instructions you
may return this product for full replacement value.
Precautions and warnings in this manual are identified with this
warning symbol. The symbol identifies conditions
that can result in damage to the opener or its components, serious injury, or death.
READ ALL INSTRUCTIONS CAREFULLY AND COMPLETELY before
attempting to install and use this automatic gate opener. This gate opener
produces a high level of force. Stay clear of the unit while it is operating and
exercise caution at all times.
All automatic gate openers are intended for use on vehicular gates only.
rev - 03/02/05
GTO/PRO • 3121 Hartsfield Road • Tallahassee, Florida, USA 32303
Telephone GTO/PRO Sales: 1-800-543-GATE (4283) or (850) 575-0176 • Fax (850) 575-8912
or GTO/PRO Technical Service: 1-800-543-1236 or (850) 575-4144 • Fax (850)575-8950
www.gtopro.com
R2500INST
This product meets and exceeds the requirements of UL 325, the standard which regulates gate opener safety,
as established and made effective March 1, 2000, by Underwriters Laboratories Inc.
©2005 GTO, Inc.
Because GTO/PRO automatic gate openers are only part of the total gate operating system, it is the responsibility of
the consumer to ensure that the total system is safe for its intended use.
To Manually Open and Close the
Gate, Follow the Procedure Below:
CAUTION: The gate will move freely and uncontrolled when the gate operator is
removed from the gate. ONLY disconnect the operator when the operator power switch
is OFF and the gate is NOT moving.
Front or Rear Mount
Disconnecting the operator
1.
2.
Turn operator power switch OFF.
Remove hairpin clip, clevis pin, and bushing
from the front mounting point.
3. Remove the operator from the mount.
The gate can be opened and closed manually
when the operator is disconnected.
Clevis Pin
Gate Bracket
IMPORTANT: NEVER allow operator arm to hang by
the front mount - it will break from the arm weight.
Bushing
CAUTION: Because the GTO/PRO gate operator is
battery powered, disconnect the operator ONLY when the
power switch on the operator is turned OFF. Unplugging
the transformer does not turn power to the operator OFF.
NOTE: Substitute a Pin Lock for the clevis pin on the front
mount of the gate opener to prevent unauthorized removal of the
opener from the gate (see Accessory Catalog).
1
Hairpin Clip
IMPORTANT SAFETY INSTRUCTIONS
For The Consumer
WARNING: To reduce the risk of injury or death:
1.
READ AND FOLLOW ALL INSTRUCTIONS. Failure to meet the requirements set forth in the instruction
manual could cause severe injury and/or death, for which the manufacturer cannot be held responsible.
2.
When designing a system that will be entered from a highway or main thoroughfare, make sure the system is placed
far enough from the road to prevent traffic congestion.
3.
The gate must be installed in a location that provides adequate clearance between it and adjacent structures when
opening and closing to reduce the risk of entrapment. Swinging gates must not open into public access areas.
4.
The gate and gate opener installation must comply with any applicable local codes.
I. Before Installation
1.
Verify this opener is proper for the type and size of gate, its frequency of use and the proper class rating.
2.
Make sure the gate has been properly installed and swings freely in both directions. Repair or replace all worn or
damaged gate hardware prior to installation. A freely moving gate will require less force to operate and will
enhance the performance of the opener and safety devices used with the system.
3.
Review the operation of the system to become familiar with its safety features. Understand how to disconnect the
opener for manual gate operation (see page 1).
4.
This gate opener is intended for vehicular gates ONLY. A separate entrance or gate must be installed for
pedestrian use (see page 6).
5.
Always keep people and objects away from the gate and its area of travel. NO ONE SHOULD CROSS THE
PATH OF A MOVING GATE.
6.
Pay close attention to the diagram below and be aware of these areas at all times.
ZONE 2
ZONE 1
Entrapment
Zones for a
Pull-To-Open
Application
ZONE 5
ZONE 3
ZONE 4
Driveway
2
Gate in the
Open Position
IMPORTANT SAFETY INSTRUCTIONS
Entrapment Zones for a proper Pull-To-Open installation:
Zone 1 – leading edge of the gate and the fence post.
Zone 2 – between the gate and the gate post.
Zone 3 – the path of the gate.
Zone 4 – the space between the gate in the open position and any object such as a wall, fence, tree, etc.
Zone 5 – pinch points between the opener and gate or post.
II. During Installation
1.
Install the gate opener on the inside of the property and fence line. DO NOT install an opener on the outside of the
gate where the public has access to it.
2.
Be careful with moving parts and avoid close proximity to areas where fingers or hands could be pinched.
3.
Devices such as contact sensors (safety edges) and non contact sensors (photo beams) provide additional protection
against entrapment.
4.
If push buttons or key switches are installed, they should be within sight of the gate, yet located at least 10 feet from
any moving part of the gate (see diagram below). Never install any control device where a user will be tempted to
reach through the gate to activate the gate opener.
5.
Do not activate your gate opener unless you can see it and can determine that its area of travel is clear of people,
pets, or other obstructions. Watch the gate through its entire movement.
6.
Secure outdoor or easily accessed gate opener controls in order to prohibit unauthorized use of the gate.
Pull-To-Open
Application
10'
10'
10'
Moving Gate
Area
Driveway
NEVER INSTALL
any control device
within gray area
3
10'
IMPORTANT SAFETY INSTRUCTIONS
III. After Installation
1.
Attach the warning signs (included) to each side of the gate to alert the public of automatic gate operation. It is
your responsibility to post warning signs on both sides of your gate. If any of these signs or warning decals become
damaged, illegible or missing, replace them immediately. Contact GTO/PRO for free replacements.
2.
The gate is automatic and could move at any time, posing a serious risk of entrapment. No one should be in contact
with the gate when it is moving or stationary.
3.
Do not attempt to drive into the gate area while the gate is moving; wait until the gate comes to a complete stop.
4.
Do not attempt to "beat the gate" while the gate is closing. This is extremely dangerous.
5.
Do not allow children or pets near your gate. Never let children operate or play with gate controls. Keep the
remote controls away from children and unauthorized users; store controls where children and unauthorized users do
not have access to them.
6.
KEEP GATES PROPERLY MAINTAINED. Always turn power to opener OFF before performing any
maintenance. Clean the push-pull tube with a soft, dry cloth and apply silicone spray to it at least once per month.
7.
Service the gate and gate opener regularly. Grease hinges and replace the battery every 3-5 years.
8.
To operate this equipment safely, YOU must know how to disconnect the opener for manual gate operation
(see page 1). If you have read the instructions and still do not understand how to disconnect the opener, contact the
GTO/PRO Service Department.
9.
Disconnect the opener ONLY when the power is TURNED OFF and the gate is NOT moving.
10.
Make arrangements with local fire and law enforcement for emergency access.
11.
Distribute and discuss copies of the IMPORTANT SAFETY INSTRUCTIONS section of this manual with all
persons authorized to use your gate.
12.
IMPORTANT: Save these safety instructions. Make sure everyone who is
using or in the vicinity of the gate and gate opener are aware of the dangers
associated with automated gates. In the event you sell the property with the
gate opener or sell the gate opener, provide a copy of these safety instructions
to the new owner.
Should you lose or misplace this manual, a copy can be obtained by
downloading one from the GTO/PRO web site (www.gtopro.com), by
contacting GTO/PRO, at 3121 Hartsfield Road, Tallahassee, Florida 32303 or
by calling 1-800-543-4283 and requesting a duplicate copy. One will be
provided to you free of charge.
4
IMPORTANT SAFETY INSTRUCTIONS
Secondary Means of Protection Against
Entrapment
As specified by Gate Opener Safety Standard, UL 325 (30A.1.1), automatic gate openers shall have an inherent entrapment
sensing system, and shall have provisions for, or be supplied with, at least one independent secondary means to protect
against entrapment. GTO/PRO gate operators utilize Type A, an inherent (i.e., built-in) entrapment sensing system as the
primary type of entrapment protection. Also, the GTO/PRO gate operator has provisions for the connection of Type B2
protection to be used as the secondary type of entrapment protection, if desired.
1. For gate openers utilizing a contact sensor (e.g., safety edge sensor– Type B2) in accordance with UL 325 (51.8.4 [i]):
A. One or more contact sensors shall be located at the leading edge, bottom edge, and post edge, both inside and
outside of a vehicular swing gate system.
B. A hard wired contact sensor shall be located and its wiring arranged so that the communication between the
sensor and the gate opener is not subjected to mechanical damage.
C. A wireless contact sensor such as one that transmits radio frequency (RF) signals to the gate opener for
entrapment protection functions shall be located where the transmission of the signals are not obstructed or
impeded by building structures, natural landscaping or similar obstruction. A wireless contact sensor shall
function under the intended end-use conditions.
Leading Edge Contact Sensor
on both sides of the gate
Vehicular Gate
Post Edge Contact Sensor
on both sides of the gate
Bottom Edge Contact Sensor
on both sides of the gate
ENTRAPMENT ALARM (UL 325; 30A.1.1A)
The GTO/PRO Gate Opener is designed to stop and reverse within 2 seconds when the gate comes in contact with
an obstruction. Additionally, these openers are equipped with an audio entrapment alarm which will activate if the
unit obstructs twice while opening or closing. This alarm will sound for a period of 5 minutes, or until the opener
receives an intended signal from a hardwired entry/exit source (e.g. push button control or keypad) and the gate
returns to a fully open or fully closed position. Turning the power switch on the control box OFF and back ON will
also deactivate the alarm. Wireless controls such as transmitters and wireless keypads will not deactivate the alarm.
5
IMPORTANT SAFETY INSTRUCTIONS
Required Safety Precautions for Gates
Install Warning Signs
Warning signs alert people of automatic gate operation and are required when installing the GTO/PRO gate operator.
Furthermore, a walk-through gate must be installed if pedestrian traffic is expected near the vehicular gate. We recommend
using the GTO/PRO Bulldog Pedestrian Gate Lock (Call the GTO/PRO Sales Department) for controlled access.
Bulldog Pedestrian
Gate Lock
(recommended, not included)
Pedestrian Gate
Contact Sensor
Warning Sign
(recommended, not included)
Vehicular Gate
Contact Sensor
(recommended, not included)
Contact Sensor
(recommended, not included)
Entrapment Protection
GTO/PRO’s inherent obstruction settings, even when properly adjusted, may not be sensitive enough to prevent bodily
injury in some circumstances. For this reason, safety devices such as safety edge sensors (or photoelectric sensors), which
stop and reverse gate direction upon sensing an obstruction, are suggested for enhanced protection against entrapment.
Warning Signs
! WARNING
The warning signs (at right) must
be installed on both sides of the
gate (see page 7 for details).
Moving Gate Can Cause
Injury Or Death
1. KEEP CLEAR! Gate may move at any time.
2. Do not allow children to operate gate or
play in gate area.
3. This gate is for vehicles only. Pedestrians
must use a separate entrance.
6
IMPORTANT SAFETY INSTRUCTIONS
These warning labels should be found at the
locations specified below. If any of them are
missing, immediately contact GTO/PRO for
replacements.
!
DC 2500 Series
US
C
LIS ED
T
#xxxxxxx
Conforms to UL 325 STANDARDS
Maximum Gate: 500 lb. (226.7 kg); 16 ft. (4.8 m)
Voltage: 12 Vdc; Frequency: 0 Hz; Power: 25 W
Class I, II, III and IV Vehicular Swing Gate Operator.
Serial Number: XXXXXXXXXX
TO MANUALLY OPEN AND CLOSE THE GATE:
1. Turn control box power switch OFF.
2. Disconnect front or rear mount from gate bracket.
3. Pull opener away from front or rear mount.
Disconnect operator ONLY when the control box power
switch is OFF and the gate is NOT moving.
GTO, Inc. Tallahassee, Florida USA
Número de identificación y etiqueta de instrucciones para
operación manual (1) ubicados en la cubierta de la caja
de control.
Avisos de advertencia (2 suministrados) que deben instalarse uno
en cada lado de la puerta (entre 90 cm y 1,5 m por encima del borde inferior de la puerta).
El logo y dos (2) etiquetas de advertencia que deben ser instaladas
sobre la caja del abridor, en ambos lados.
7
Single Gate Opener Parts List
Opener and Mounting Hardware
Gate Opener (1)
w/ 6' Power Cable
Closed Position
Stop Plate (1)
Post Bracket (2)
Post Pivot Bracket (1)
®
ER
EN
TE OP
E-Z GA
Customer Support Card (1)
Hardware
3/8" x 8" Bolt (4)
3/8" Washer (9)
3/8" x 3" Bolt (2)
3/8" Lock Washer (7)
3/8" x 2" Bolt (1)
5/16" Washer (1)
5/16" x 1-3/4" Bolt (1)
2" Mounting Screw (5)
8" Nylon Cable Tie (14)
Gate Bracket (1)
3/8" x 1-1/4" Clevis Pin (2)
Hairpin Clip (2)
8
3/8" Nut (7)
5/16" Nut (1)
3/8" Bushings (2)
Single Gate Opener Parts List (continued)
Control Box and Electrical Components
Battery (1)
! WARNING
Receiver (1)
GTO Transmitter(1)
Moving Gate Can Cause
Injury Or Death
1.
KEEP CLEAR! Gate may move at any time.
2.
Do not allow children to operate gate or
play in gate area.
3.
This gate is for vehicles only. Pedestrians
must use a separate entrance.
Warning Signs (2)
Transformer (1)
Control Box (1)
Tools Needed
• Power Drill
• Open End Wrenches — 3/8", 7/16", 1/2", and 9/16"
• 3/8" Drill Bit
• Hacksaw or Heavy Duty Bolt Cutters
• Small (Flat Bladed) Screwdriver
• Phillips Screwdriver
• Tape Measure
• Level
• Wire Strippers
• C-Clamps — small, medium, and large
• Center Punch
• Extra person will be helpful
YOU MAY ALSO NEED THESE ITEMS BEFORE YOU BEGIN THE INSTALLATION
(Some of these items can be found in the Accessory Catalog page 37):
•
Low voltage wire will be needed to run from the transformer to the control box; length depends upon the distance between the
transformer power supply and the control box. See Powering the System on page 19, and the Accessory Catalog.
•
If your gate is more than 1000' away from an ac power source you will need to use at least one GTO/PRO 5 watt Solar Panel to
trickle charge the battery. See the Accessory Catalog.
•
If your fence post is made of wood and is less than 6" in diameter or 6" square, see page 12.
•
If your fence post is larger than 6" in diameter you will need threaded rods or carriage bolts longer than 8". See page 15.
•
PVC conduit.
•
If you have thin walled tube or panel gates, see Recommended Reinforcement Examples on page 12.
•
Depending on the type of gate, a horizontal cross member or mounting plate may be needed to mount the front of the opener
and gate bracket to the gate. See page 11, step 2; page 15, step 10.
•
Surge protection for transformer.
•
Some types of installations require U-Bolts.
•
If the gate is a push-to-open refer to page 36
•
Additional washer or a metal plate may be needeed for wooden post.
9
Technical Specifications
GTO/PRO 2500 GATE OPERATOR
DRIVE
• Low friction screw drive (linear actuator) rated for -5 ºF to +160 ºF (-28 ºC to +71 ºC).
• Powered by a 12 V motor with integral case hardened steel gear reducer. Motor speed reduced to 260 rpm. Generates
680 ft. lb. of torque at 12 V.
• Maximum opening arc of 110º. Approximate opening time (90º): 20 seconds, depending on weight of gate.
POWER
• The system is powered by a 12 Vdc, 7.0 Ah, sealed, rechargeable lead acid battery.
• Battery charge is maintained by a 120 Vac input, 18 Vac output transformer rectified to 14.5 Vdc (40 VA) through the
GTO/PRO control board. One (1) blade-style control board fuse is rated for 25 A.
NOTE: The transformer should not be directly connected to any battery. Do not replace fuses
with higher ampere rated fuses; doing so will void your warranty and may damage your control board.
• Battery charge is maintained by a GTO/PRO Solar Panel Charger: float voltage of 14.5 Vdc output is from a 193/8" x
81/2" silicon alloy panel. Generates a minimum of 5 W at 300 mA. A gated diode on the control board prevents
battery discharge.
CONTROL
• GTO/PRO microprocessor-based control board is set for single leaf, pull-to-open gate installations. DIP switches
can be adjusted to accommodate an optional kit for push-to-open gates (see Accessory Catalog).
• Control board has temperature compensated circuits.
• A circuit on the control board regulates charging. "Sleep draw" is 40 mA; "active draw" is 2 to 5 A.
• Auto-memorization of digital transmitter code.
• GTO/PRO remote-mounted RF receiver tuned to 318 MHz.
• Opener length with push-pull tube fully retracted is 401/4", mounting point to mounting point.
• Adjustable auto-close timer, and obstruction sensitivity.
• Power terminal block accommodates a transformer or solar panels.
• DIP switches simplify setup of gate opener.
• Accessory terminal block is fully compatible with push button controls, digital keypads, safety loops, etc.
• Control board allows connection of safety edge sensors and photoelectric sensors.
• Audio entrapment alarm sounds if unit encounters an obstruction twice while opening or closing.
OPERATIONAL CAPACITY
• The Gate Capacity Chart shows approximate cycles, per day, you can expect from the GTO/PRO SW-2500 Automatic Gate Operator when powered with a transformer. Actual cycles may vary slightly depending upon the type and
condition of gate and installation.
GTO/PRO SW2500 Gate Capacity / Cycle Chart
Estimated number of daily cycles, based on use with a transformer and one(1) 12 Volt battery.
Number of Cycles Per Day
Gate Weight
IMPORTANT: BALL BEARING HINGES SHOULD BE
USED ON ALL GATES
WEIGHING OVER 250 Lbs.
500 lbs.
400 lbs.
300 lbs.
200 lbs.
150 lbs.
100 lbs.
50 lbs.
165
175
185
195
205
215
225
5’ - 6’
155
165
175
185
195
205
215
8’
145
155
165
175
185
195
205
10’
Gate Length
135
145
155
165
175
185
195
12’
125
135
145
155
165
175
185
14’
100
125
135
145
155
165
175
16’
To determine the number of cycles the gate opener will perform using solar panels, please see the specifications
listed on page 19 or call (800) 543-1236 or (850) 575-4144 for more information.
* An operation cycle is one full opening and closing of the gate.
These specifications are subject to change without notice.
10
Installation Overview
Pull-to-Open Gates (Gate Opens into the Property)
The diagram shown below is an example of a pull-to-open installation on a chain link fence and single gate. Mounting the
opener on a masonry column requires special procedures; see Column Installation Information on page 36 if you intend
to mount the opener on a column. Furthermore, if you have a push-to-open gate, you will need to purchase a push-to-open
bracket (see Accessory Catalog) to properly configure your system. See Push to Open Installation on page 30 before
proceeding.
Receiver
Control Box with Battery
Gate Swings Evenly and Freely
Hung Firmly and Plumb
Horizontal Cross Member
Post Bracket Assembly
Single Gate Opener
120 Volt indoor
Transformer
(surge protector
not supplied)
Warning Sign
Power Cable
Gate Bracket
Closed Position Positive Stop Plate
Fence Post Set in Concrete
Run 1000' (max.) of low
voltage wire to control
box from transformer
(wire not included).
PVC conduit (not included)
to protect wire from lawn
mowers and weed eaters.
Preparation of the Gate
Step 1
Horizontal Cross Member
The gate must be plumb, level, and swing freely on its
hinges. Wheels must not be attached to the gate. The
gate must move throughout its arc without binding or
dragging on the ground. Note that gates over 250 lb.
should have ball bearing hinges with grease fittings.
Step 2
The fence post must be secured in the ground with
concrete so it will minimize twist or flex when the
opener is activated. We recommend you position the
opener near the centerline of the gate to keep the gate
from twisting and flexing. The addition of a horizontal
or vertical cross member (if one is not already in place)
to provide a stable area for mounting the gate bracket is
also important.
Vertical Cross Member
11
Installation of Mounting Hardware
The position of the post bracket determines the leverage and efficiency of the opener. The post bracket position also sets the
clearance between the opener and gate in the open and closed positions (minimum 2 inches for safety reasons).
The curved design of the post bracket works well for installations on round and square fence posts. Because the post bracket
carries the entire thrust of the active opener, bolts that completely penetrate the fence post must be used.
On wooden posts, place a metal plate or washer
(not supplied) between the nuts and the fence
post to prevent the thrust of the opener from
pulling the bolts and washers out of the wood.
Metal Plate
Wooden Post
NOTE: A fence post smaller than 6" in diameter
or 6" square should be made of metal instead of
wood so that it will remain stable while the
opener is moving the gate.
Wooden Post
Metal Plate
Post
Bracket
Post Bracket
Post
Pivot Bracket
Post Pivot Bracket
Larger than 6" diameter post
Center of Gate Hinge
On round posts of 6" diameter or larger, the post pivot bracket may
not be necessary for the installation. In this instance, the two post
brackets are mounted by themselves.
Pull-to-Open Installation
IMPORTANT:
We strongly recommend using steel pipe, wood or metal to reinforce thin walled tube gates or wood to reinforce panel gates
as shown. These reinforcement methods will prevent damage to the opener and gate when the opener is installed.
Recommended Reinforcement Examples
Steel Pipe Cut in Half
(not supplied)
Gate Bracket
Gate Bracket
Panel Gate
Gate Bracket
1" x 6" Wood Reinforcement
Thin Walled Tube Gate
Wood or Metal
Reinforcement
(not supplied)
12
Determining the Mounting Position
of the Post Bracket Assembly and the Gate Bracket
Post Bracket Assembly
Step 3
Insert the 3/8" x 2" bolt through
the center hole of the post
brackets and post pivot bracket as
shown. Fasten a 3/8" lock
washer, 3/8" washer and 3/8" nut
on the end of the bolt. DO NOT
overtighten the nut because the
post pivot bracket will have to be
adjusted later.
NOTE: The following steps are
intended for pull-to-open gate
installations. If you are mounting
your opener on a push-to-open gate
(e.g., a gate on a sloped driveway)
you will need to purchase a Push To
Open bracket (see Accessory
catalog). Also, see Push-to-Open
Installation beginning on page 30.
3/8" x 2" Bolt
Post Bracket
Post Pivot Bracket
Post Bracket
3/8" Washer
3/8" Lock Washer
3/8" Nut
Step 4
Attach post bracket assembly and gate bracket to the opener with the clevis pins and bushings. Secure the clevis pins with
hairpin clips.
Front Mount
Clevis Pin
Rear Mount
Bushing
Clevis Pin
Gate Bracket
Opener
Bushing
Hairpin Clip
Post Bracket Assembly
Hairpin Clip
Step 5
With the gate in the open position (up to 110º from its closed position), and the opener fully retracted, adjust the post
bracket assembly and gate bracket until the opener is level. While holding the opener level, use C-clamps to temporarily
keep the post bracket assembly and gate bracket in their respective positions on the fence post and gate.
Post Bracket Assembly
Level Opener
LEVEL hori
zontal cro
ss membe
Gate In Open Position Fence Post
13
r
Gate Bracket
IMPORTANT: While determining the mounting point for the post pivot bracket assembly, be sure that the position allows
for a minimum of 2 inches of clearance between the gate and the opener in both the open and closed positions, as shown in
the diagrams below. This clearance will give the opener the most efficient leverage point for opening and closing the gate and
more importantly provides the least possible pinch area.
Step 6
When you feel that you have the best position for the post pivot bracket in the open position, insert the 5/16" x 1-3/4" bolt
through the aligned holes of the post bracket and post pivot bracket to hold it in place. Remove the clevis pin from the front
mount and while supporting the gate opener, swing the gate and gate opener to the closed position. With the gate and gate
opener in the closed position, check the clearance and be sure that the gate opener is not binding at the post pivot bracket.
If you don't have 2 inches of clearance or the gate opener is binding on the post pivot bracket, remove the 5/16" x 1-3/4" bolt
and readjust the pivot bracket until you can achieve these important clearances.
With the post pivot bracket in the optimum position for clearance and freedom of movement, reattach the opener to the gate
bracket in the open position and recheck the gate opener level and make sure the brackets are clamped securely.
2" minimum
Gate in the
CLOSED POSITION
Pinch Area
Be sure gate opener
and bracket don't bind.
Pinch Area
Gate in the
OPENED POSITION
2" minimum
TIP: Turning the pivot bracket over gives
more hole alignment options for the post
pivot bracket assembly. You can also move
the entire post pivot bracket assembly to
different positions on the gate post to help
achieve the proper clearances.
14
Installing the Post Bracket Assembly and Gate Bracket
Mark fence post through middle of bracket slots
and drill 3/8" holes
Step 7
Mark reference points for bolt holes on the fence post through
middle of bracket slots. Marking reference points in this
manner allows room for adjustment when mounting the post
bracket assembly and gate bracket. After marking your
reference points, remove the opener and brackets from the fence
and gate.
EXAMPLES
TOP VIEW
Step 8
Post Bracket
Assembly
Drill 3/8" holes into fence post as marked.
Round Metal Post
Step 9
Fasten post bracket assembly to the fence post using
(4) 3/8" x 8" bolts, washers, lock washers, and nuts (provided).
Remove excess bolt length extending beyond the tightened nuts
with a hacksaw or bolt cutters.
Square Metal Post
SIDE VIEW
NOTE: In cases where the fence post has a diameter larger than
6", threaded rods or carriage bolts longer than 8"
(not supplied) must be used.
Step 10
Square Wood Post
Remove excess bolt length with hacksaw or bolt cutters
Round Wood Post
Mark reference points for bolt holes on the
gate cross member through middle of gate
bracket slots. Drill 3/8" holes into the gate
cross member as marked.
Gate In Open Position Mount gate bracket using (2)
3/8" x 3" bolts, washers, lock washers, and
nuts (provided). Cut off excess bolt
length extending beyond the tightened
nuts.
LEVEL ho
rizontal cr
oss membe
r
Mark cross member through middle of
gate bracket slots and drill 3/8" holes
Gate Bracket Mounting Examples
FRONT VIEW
SIDE VIEW
FRONT VIEW
SIDE VIEW
Mounting Plate Created for Decorative Gate
(required but not
supplied)
Round Tube & Chain Link Gate
Remove excess bolt length with hacksaw or bolt cutters
Square Tube Gate
15
Mounting the Opener
Step 11
Attach the opener to the securely bolted post bracket assembly and gate bracket using clevis pins, bushings, and hairpin clips,
or optional Pin Locks (see Accessory Catalog). Verify that the opener is level and adjust the post bracket assembly if
necessary.
Post Bracket Assembly
bolted to fence post
Level Opener
LEVEL hori
Gate Bracket bolted
to gate cross member
zontal cros
s member
Clevis Pin, Bushing, and Hairpin Clip
Clevis Pin, Bushing, and Hairpin Clip
Gate In Open Position Fence Post
Installation of the Closed Position Stop
The Mighty Mule® Gate Opener firmly holds the gate in the closed position using the positive stop plate. The
positive stop helps stabilize the gate leaf in the closed position. To further enhance the stability and security of
your gate, install the optional Mighty Mule® Automatic Gate Lock (see Accessory Catalog).
Step 12
Gate Hinge
Remove hairpin, clevis pin, and bushing from front mount
and close the gate (remember to support opener). Fasten the
closed position stop plate to the end of the gate frame on the
gate centerline, but do not tighten it completely. Slide the
stop plate toward the fence post until they touch (see
illustration). Once you have moved the stop plate to the
correct position, tighten its hardware completely.
Closed Position Stop Plate
The gate can open
up to 110º (max.)
Use the appropriate hardware for your type of gate (use
U-bolts if you have a tube or chain link gate; wood or lag
screws for wood gates; etc.). This hardware is not
provided.
SIDE VIEW
Gate Post
Closed Position Stop Plate mounted on metal post with U-bolts.
Fence Post
TOP VIEW
16
At this stage of the installation, the opener should be installed on the
gate and the closed position stop should be in place.
Check List
• The gate is plumb, level, and swings smoothly on its hinges.
• A plate or support was added for the gate bracket (if necessary).
• The opener is level and mounted on the centerline of the gate.
Gate Swings Evenly and Freely
Hung Firmly and Plumb
Horizontal Cross Member
Post Bracket Assembly
Single Gate Opener
Gate Bracket
Closed Position Positive Stop Plate
Fence Post Set in Concrete
Mounting the Control Box
Step 13
Mount the control box using the screws (provided) or another
secure mounting method. The control box must be mounted at
least 3 feet above the ground to protect it from rain splash,
snow, etc., and at least 3 feet from an AC power source to
prevent electrical interference.
Use mounting
holes and screws
provided to mount
control box to a
secure surface.
NOTE: The battery that came with your Mighty
Mule®, MUST be placed in the top (horizontal)
battery slot with the terminals on the RIGHT. The
extra (vertical) battery slot is for an optional second
battery. An optional second battery can be used for
solar and/or high traffic applications, if needed..
17
Connecting Opener Power Cable
Step 14
BLACK
Make sure the control box power switch is in the OFF position.
The ON/OFF Switch is located on the bottom of the control box.
Remove the control box cover and slide the battery into position
with its terminals to the RIGHT (see illustration). Connect the
BLACK battery wire to the NEGATIVE (–) battery terminal.
Connect the RED battery wire to the POSITIVE (+) terminal.
Pay close attention to the color of the wires. If the wires are
connected incorrectly, the control board will be damaged.
NEVER insert the battery with the terminals to the left.
RED
BLACK wire to NEGATIVE (–) terminal
RED wire to POSITIVE (+) terminal
12 Volt Battery
(included)
Step 15
J1
J2
J9
~ ~ + NC RLY-COM NO
18 VAC SOLAR RELAY OUT
WHT
BRN
15
BLUE
J6
BAT+
800-543-GATE
BLK
J21
RED
www.gtoinc.com
ORG
SLAVE INPUTS
FUSE
GTO, Inc.
3121 Hartsfield Rd
Tallahassee, FL 32303
GRN
SWITCH
Strip approximately 3/16" of insulation from each wire of
the opener power cable. Twist each exposed wire tightly
(there are seven [7] wires inside the power cable sheath).
Loosen sealing nut on strain relief hub at bottom of
control box. Insert power cable into control box through
strain relief. Thread approximately 6" of the power cable
into the control box and retighten sealing nut until the
power cable locks into place.
BLUE
J13
ALARM
BRN
ORG
RED
MASTER INPUTS
WHT
BAT–
SWITCH
GRN
Battery wires for
optional second battery.
BLK
J5
COM
J11
COM
CYCLE
CLOSE
SAFETY
J8
EXIT
OPEN
SHADOW
LOOP
3
4
SET
LIMIT
4
5
ON
6
OFF
7
STALL FORCE
RED
OFF
MAX
Strain Relief
2
3
1 2 3 4
1
2
DUAL ON
MODES
1
BLK
1 2 3 4 5 6 7 ON
N
J12
RECEIVER
GRN
MI
LEARN
TRANSMITTER
OPEN
EDGE
MODES ON
CLOSE
EDGE
Space for optional
second 12 Volt battery
(see Accessory Catalog)
Lock Nut
Hub
Strain Relief
Sealing Nut
Operator Power Cable
SWITCH
GRN
Step 16
BRN
ORG
RED
COM
J11
COM
Tighten the set screws against the end of the wires.
A dab of petroleum jelly on each terminal will help
prevent corrosion.
J5
BLK
Power cable from
operator (master) arm
J13
BLUE
MASTER INPUTS
WHT
Insert the stripped power cable wires into the
appropriate terminals on the OPENER terminal
block. The green wire should be inserted into the
GRN terminal, the blue wire into BLU, the orange
wire into ORG, black wire into BLK, and the red
wire into the RED terminal, white wire into WHT,
and brown wire into BRN.
CYCLE
CLOSE
SAFETY
Wrong
Correct
J8
EXIT
OPEN
SHADOW
LOOP
CLOSE
EDGE
Wrong
OPEN
EDGE
STALL FORCE
J12
BLK
RED
RECEIVER
GRN
MIN
MAX
Wire
Terminal Block
Wire
Terminal Block
18
Wire
Terminal Block
Powering the System
Installation of the Transformer
IMPORTANT:
•
The transformer is designed and intended for indoor use. If the transformer can be plugged only into
an outside electrical outlet, a weatherproof cover or housing (available at local electrical supply stores)
must be used.
•
All low voltage wire used with the GTO/PRO Gate Opener must be 16 gauge dual conductor,
multi-stranded, direct burial wire (see page 20 and the Accessory Catalog). Do not run more than
1000 feet of wire.
•
If your gate is more than 1000 ft. from an ac power source, you will need to use at least one 5 watt
Solar Panel to charge the battery (see Accessory Catalog). Refer to the Solar Panels and Gate
Activity chart below.
Optional Solar Panels and Gate Activity
The table and map
illustrate the maximum
number of gate cycles to
expect per day in a
particular area when using
from 5 to 30 watts of solar
charging power. (see
Accessory Catalog). The
figures shown are for
winter (minimum sunlight)
and do not account for the use of any
accessory items. Accessories connected to
your system will draw additional power from
the battery.
Winter Ratings
12 v single gate (5 watts) solar charger
12 v single gate (10 watts) solar charger
12 v single gate (15 watts) solar charger
12 v single gate (20 watts) solar charger
12 v single gate (25 watts) solar charger
12 v single gate (30 watts) solar charger
Zone 1
4
8
11
14
17
20
Zone 2
Zone 3
8
16
20
28
36
44
13
26
30
38
46
54
NOTE: A maximum of 30 watts of solar
charging power can be connected to the
GTO/PRO Gate Opener. Consult Solar Panel
Installation Instructions for further
information.
Step 1
Make sure the power switch is OFF before proceeding to the next step.
Step 2
ON/OFF Switch
Select the electrical outlet iwhere you will plug the transformer.
Measure the distance from this outlet to the control box following the
path where the wire will be laid. After you have measured how much
wire is needed, cut the wire to the appropriate length.
19
IMPORTANT INFORMATION ABOUT LOW VOLTAGE WIRE
The only wire acceptable for use with GTO/PRO products is 16 gauge multi-stranded, low voltage, PVC
sheathed wire. This particular gauge enables the transformer to provide an adequate charge through the
control board to the battery at distances up to 1000 ft.
DO NOT use telephone wire or solid core wire. Unlike multi-stranded wire, these types of wire are
inadequate for use with your gate opener system. Telephone wire and solid core wire do not deliver
enough voltage for your gate opener to function and will cause the system to go into a condition known
as "low voltage lockout."
NEVER splice wires together. Splicing permits corrosion and seriously degrades the wire's ability to
carry an adequate current.
Step 3
Lay the measured length of low voltage wire in a trench following a path from
the selected electrical outlet to the control box. Wires coming up from the
ground should be run through PVC conduit to protect them from lawn mower
blades, weed eaters, and grazing animals. Be sure to bury the wire laid in the
trench.
Step 4
Feed the low voltage wires upward through the strain relief opening on the
lower left of the control box. Pull 6" to 8" of wire into the control box and
tighten the strain relief screw to secure the wires.
WARNING! DO NOT PLUG THE TRANSFORMER
INTO AN OUTLET DURING THIS STEP! THE
TRANSFORMER MUST ONLY BE PLUGGED INTO
AN OUTLET DURING STEP 7!
Low Voltage Wire
from Transformer
PVC Pipe
J1
J2
Low Voltage Wire
from AC Transformer
J9
GRN
WHT
Strip 3/16" off the ends of the low voltage wire and
twist tightly. Attach these ends to the 18VAC
terminals located on the POWER IN terminal block
(see illustration at right). Be certain not to let the
exposed wires touch each other!
~ ~ + NC RLY-COM NO
18 VAC SOLAR RELAY OUT
RED
BLACK
Step 5
Power Cable from
Opener Arm
J6
BLUE
BRN
ORG
BLK
J21
RED
SLAVE INPUTS
Insert one transformer wire into an 18VAC terminal.
Insert the other transformer wire into the remaining
18VAC terminal. The transformer wires can be
connected to the 18VAC terminals regardless of color.
SWITCH
GRN
J13
BRN
ORG
RED
J5
BLK
20
BLUE
MASTER INPUTS
Power Cable
from Operator (master)
WHT
Tighten set screws against exposed end of wires. A
dab of household petroleum jelly on each terminal will
help prevent corrosion.
Step 6
Strip 1/2" of insulation from the ends of the low voltage
wire. Attach these stripped ends to the transformer
terminals.
A dab of household petroleum jelly on each terminal will
help prevent corrosion.
Make sure the exposed wires do not touch each other!
Step 7
Transformer
HINT: Keep a few mothballs in the control box to
discourage insects from entering it and damaging the
control board.
21
SURGE PROTECTOR
Plug the transformer into the electrical outlet.
(Use of a surge protector with the transformer is strongly
recommended.)
CONTROL BOARD SETTINGS
DIP Switches
1 2 3 4 5 6 7 ON
ON
5
6
7
OFF
J8
COM
CYCLE
CLOSE
J11
COM
J12
OPEN
EDGE
4
EXIT
OPEN
3
CLOSE
EDGE
2
SHADOW
LOOP
1
DIP Switch #1 - Soft Start/Stop
The Soft Start/Stop feature slowly starts the gate
as it begins to open and slows the gate as it comes
to the closed position. This saves wear and tear on
the gate and gate opener system.
SAFETY
Main DIP Switch Settings (MODES)
GRN
BLK
RED
RECEIVER
DIP#6 DIP#7 Delay Time for Auto-Close
DIP Switch #2 - Warning Buzzer
The Warning Buzzer alerts you when the gate
opener is beginning to either open or close the
gate. It sounds for the first 2 seconds in each
direction. It also sounds a warning when the gate
obstructs two times in one cycle. Switching this to
OFF only disables the open and close warning not
the obstruction warning.
ON
ON
OFF
OFF*
ON
OFF
ON
OFF*
15 seconds
30 seconds
60 seconds
120 seconds (factory preset)
DIP#5
D1 mode, constant pressure to operate gate.
ON
OFF* B2 mode, momentary contact to operate gate.
DIP Switch #3 - Auto-Close
With the Auto-Close switch in the OFF position
the gate will remain open until it receives another
signal from an activation device such as a
transmitter, keypad, or push button control. With
the Auto-Close switch in the ON position the gate
opener will automatically close the gate. The time
the gate will remain open is determined using DIP
Switches #6 and #7.
DIP#4
ON
Push-to-open operation.
OFF* Pull-to-open operation.
DIP#3
ON
Auto-close enabled.
OFF* Auto-close disabled.
DIP#2
ON* Buzzer warning enabled.
OFF Buzzer warning disabled
(for auto-close and soft start/stop only).
DIP Switch #4 - Push/Pull-to-Open
If your gate opens into the property the DIP
Switch is set to the OFF position (factory setting).
If your gate opens out from the property the DIP
Switch must be set to the ON position. NOTE: if
you have a Push-to-Open gate application you will
need a Push-to-Open bracket (see Push-to-Open
Instructions on page 30).
DIP#1
ON* Soft start enabled.
OFF Soft start disabled.
* Factory preset.
DIP Switch #5 - B2/D1 Mode
This DIP Switch must remain in the OFF position
unless the gate opener is going to be used by a
guard or gate attendant, who can only open the
gate when constant pressure is applied to a push
button control device.
IMPORTANT CONTROL BOARD SETTINGS:
CONTROL BOARD DIP SWITCH #1 is
factory preset in the ON position
and MUST remain in the ON
position. Changing this setting can
damage your gate, gate opener and
possibly void your warranty!
DIP Switches #6 and #7
The combination of these two switches determines
the amount of time the gate will remain open
when DIP Switch #3 is set to the ON position.
22
Setting the Closed Position Limit
TURN CONTROL BOX ON
Your GTO/PRO gate operator has two Limit Settings
1) OPEN Limit setting: (Gate in the OPEN POSITION / the limit is FACTORY SET and NOT ADJUSTABLE) The open
limit setting is the fully open position.
2) CLOSED Limit setting: (Gate in the CLOSED POSITION) To achieve optimum closed position, you are required
to complete the following FOUR STEPS:
Step 1
Confirm that the power switch is in the ON position and the gate is in the OPEN POSITION.
Step 2
COM
J11
COM
Activate your opener by pressing the entry transmitter
button. Your gate should now be moving from the fully
open position toward the closed position. Prepare to
STOP the gate by pressing the entry transmitter button
again when the gate reaches the desired closed position.
This step may be repeated until desired close position is
achieved. Once the desired CLOSED position has been
achieved, proceed to step 3.
CYCLE
CLOSE
SAFETY
J8
EXIT
OPEN
SHADOW
LOOP
2
4
SET
LIMIT
3
5
6
7
RED
OFF
1 2 3 4 5 6 7 ON
1
STALL FORCE
J12
BLK
RECEIVER
MIN
GRN
With the gate in the desired closed position PRESS &
HOLD the “SET LIMIT" button on the control board for
5 seconds.
LEARN
TRANSMITTER
OPEN
EDGE
MODES ON
CLOSE
EDGE
Step 3
MAX
Step 4
Press the transmitter button and allow the gate to return
to the fully open position. YOUR GATE’S CLOSED
POSITION LIMIT IS NOW PROGRAMMED.
Set Limit Button
TESTING YOUR CLOSED LIMIT SETTING:
Press your entry transmitter and allow your gate to close. If the CLOSED position is not correct or needs to be changed, you
will need to CLEAR your CLOSED LIMIT settings and follow Steps 1-4 again.
CLEARING THE PROGRAMMED CLOSED LIMIT SETTING:
If you make a mistake and set the limit at the wrong position – press your transmitter to return the gate to the fully opened
position, then press and hold the "SET LIMIT" button for 10 seconds. This will clear the memory for the closed limit
position. Follow Steps 1-4 again.
23
Obstruction Sensitivity Potentiometer
IMPORTANT: For safety reasons the obstruction
setting or Stall Force on the GTO/PRO control board
comes from the factory set at MIN (minimum). In many
gate installations this setting will need to be adjusted to
overcome the weight and size of the gates.
1
2
3
4
ON
OFF
SET
LIMIT
The Stall Force potentiometer on the
control board operates like a volume
control on a radio. It controls the
obstruction sensitivity (or the amount of
force the opener will apply to an obstruction) before it automatically stops
and reverses direction for approximately
two (2) seconds.
1 2 3 4 5 6 7 ON
MODES ON
1
2
3
4
5
6
7
OFF
LEARN
TRANSMITTER
STALL FORCE
MAX
MIN
STALL FORCE
OPEN
EDGE
J12
CLOSE
EDGE
SAFETY
COM
CYCLE
CLOSE
COM
EXIT
OPEN
J8
J11
SHADOW
LOOP
MIN
MAX
Use a small slotted screwdriver to turn
the arrow in the center of the potentiometer. Adjust the sensitivity from the
MINIMUM position where the gate
operates without obstructing from its
own weight or the wind conditions in
your area.
1 2 3 4
DUAL ON
MODES
GRN
BLK
RED
RECEIVER
NOTE: You may need to increase the
stall force in cold weather due to increased
resistance from gate hinges.
ALWAYS KEEP SAFETY AT THE TOP OF YOUR LIST WHEN ADJUSTING OR
SERVICING YOUR AUTOMATIC GATE OPENER!
24
Setting Your Personal Transmitter Code
All GTO/PRO transmitters are set to a standard code at the factory and are ready to operate your GTO/PRO gate operator.
For your safety and security, however, we strongly recommend that you replace the factory setting with your own personal
code. Follow the directions below:
1. Remove the Transmitter Cover
On the back of the transmitter use a small phillips head screw driver to remove
the two screws on the sides of the visor clip and separate the front cover from the
transmitter. With the front cover removed, the battery and the DIP switches will
be exposed. To set a new code, use a small screwdriver to move the switches.
LE
D
+
1
2
0
3
–
4
5
6
A
A 2
7
8
3S
LK
AL
IN
E
9
12
V
EC
E
BA
TT
ER
Y
2. Set the transmitter DIP Switches
There are nine (9) transmitter DIP switches; each can be placed in three different
positions (+, 0, –). DO NOT set all the switches in the same position, such as all +,
all 0, or all –. Once the DIP switches have been set to a personal code, replace front
cover.
1 2 3 4 5 6 7 8 9
+
0
ECE
WARNING: No other adjustments should be made inside the transmitter.
3. “Teach” the New Code to Control Board Memory
COM
J11
COM
A. Press and hold transmitter button.
B. Press and hold the LEARN TRANSMITTER button on
the control board for 5 seconds.
C. Release LEARN TRANSMITTER button.
D. Release transmitter button. The new code
is stored in control board memory.
CYCLE
CLOSE
SAFETY
J8
EXIT
OPEN
SHADOW
LOOP
4
SET
LIMIT
3
5
6
7
OFF
1 2 3 4 5 6 7 ON
2
MAX
Learn Transmitter Button
25
1
RED
STALL FORCE
J12
BLK
RECEIVER
GRN
MIN
LEARN
TRANSMITTER
OPEN
EDGE
MODES ON
CLOSE
EDGE
Installing the Receiver
Use the transmitter to check the range of the receiver before permanently mounting it.
Consider the following when mounting the receiver:
• Standard receiver cable length is 10 feet (receivers with a longer cable are available as
special order items; call the GTO/PRO Sales Department). NEVER splice receiver
cable!
• Run the cable through PVC conduit to protect it from damage.
• DO NOT run cable through metal conduit because the receiver signal range will be
decreased.
• DO NOT run cable in conduit containing ac wiring.
• The receiver range can vary from 50 to 100 feet depending upon weather, topography,
and external interference.
NOTE: Do not mount upside down.
FCC Regulation
This device complies with FCC rules Part 15. Operation is subject to the following
conditions:
1. This device may not cause harmful interference.
2. This device must accept an interference that may cause undesired operation.
Transmitter distance may vary due to circumstances beyond our control. NOTE: The
manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the
user’s authority to operate the equipment.
26
Connecting Additional Safety Devices
Although GTO/PRO strongly recommends the use of additional safety devices, we do not endorse any
specific brand names. Only use products that are certified and listed to be in compliance with any
applicable UL standards (United Laboratories) and national and regional safety codes.
Call GTO/PRO Sales at 1-800-543-4283 for information on compatible
products for your specific application.
The GTO/PRO SW-2500 will ONLY accept accessory devices with normally open dry contact output.
Contact Sensors (safety edges)
If not installing a contact sensor skip to next section.
PLEASE NOTE: Contact sensors are not included with the GTO/PRO SW-2500.
The GTO/PRO SW-2500 is equipped with built-in obstruction sensitivity. The opener is designed to stop and reverse the gate
within 2 seconds when it comes in contact with an obstruction. However, obstruction sensitivity, although functioning
properly, may not be sensitive enough to prevent bodily injury in some circumstances. To augment your protection against
entrapment, GTO/PRO recommends using some form of additional safety device. When installed, contact sensors must be
mounted in compliance with UL 325, Underwriters Laboratories safety standard for gate openers. Review page 5 for
information about mounting requirements for safety edges ("contact sensors").
Refer to the sensor manufacturer’s instructions for information about installing these devices on a vehicular gate.
STALL FORCE
MIN
J8
OPEN
EDGE
J12
CLOSE
EDGE
EXIT
OPEN
COM
SAFETY
COM
CYCLE
CLOSE
Contact Sensor Input Connection:
SHADOW
LOOP
J11
Connect one of the OPEN EDGE contact sensor wires to the
COMMON (COM) terminal and the other to the OPEN
EDGE terminal on the GTO/PRO SW-2500 control board.
MAX
Make sure the power switch to the opener is turned
off before connecting safety device wiring to the
terminal blocks. Unplugging the transformer does
not turn power to the opener OFF.
GRN
BLK
RED
RECEIVER
Connect one of the CLOSE EDGE contact sensor wires to
the COMMON (COM) terminal and the other to the
CLOSE EDGE terminal on the GTO/PRO SW-2500 control
board.
Activation of a contact sensor while the gate is in motion
will cause the gate to stop and reverse within two (2)
seconds.
Wire from Contact Sensor
(open safety edge)
Wire from Contact Sensor
(close safety edge)
27
Non-Contact Sensors (photo beams)
If not installing a non-contact sensor skip to next section.
PLEASE NOTE: Non-contact sensors are not included with the GTO/PRO SW-2500.
The GTO/PRO SW-2500 can also accept "Safety" input from normally open "dry-contact" output devices such as photo
beams connected to the SAFETY input terminal.
Refer to the sensor manufacturer’s instructions for information
about installing these devices on a vehicular gate.
MIN
J8
OPEN
EDGE
CLOSE
EDGE
J12
SHADOW
LOOP
COM
EXIT
OPEN
COM
Connect one of the non-contact sensor dry contact output wires to
the COMMON (COM) terminal and the other to the SAFETY
terminal on the GTO/PRO SW-2500 control board.
SAFETY
J11
CYCLE
CLOSE
Non-Contact Sensor Connection:
MAX
Make sure the power switch to the opener is turned
off before connecting safety device wiring to the
terminal blocks. Unplugging the transformer does
not turn power to the opener OFF.
STALL FORCE
GRN
BLK
RED
RECEIVER
This input is ONLY monitored when the gate is
closing. Activating the non-contact sensor
(obstructing the safety beam path) will cause the
gate to reverse to the fully open position.
Wire from Non-Contact
Sensor (photo beam)
Shadow Loop
If not installing a shadow loop skip to next section.
PLEASE NOTE: Non-contact sensors are not included with the GTO/PRO SW-2500.
STALL FORCE
MIN
OPEN
EDGE
J12
CLOSE
EDGE
SHADOW
LOOP
EXIT
OPEN
COM
SAFETY
COM
Shadow Loop Connection:
J8
J11
CYCLE
CLOSE
Make sure the power switch to the opener is turned
off before connecting safety device wiring to the
terminal blocks. Unplugging the transformer does
not turn power to the opener OFF.
MAX
Refer to the sensor manufacturer’s instructions for information
about installing these devices on a vehicular gate.
GRN
BLK
RED
RECEIVER
Connect one of the shadow loop wires to the COMMON (COM)
terminal and the other to the SHADOW LOOP terminal on the
GTO/PRO SW-2500 control board.
The SHADOW LOOP is a detector located within the moving
path of the gate to prevent the gate from closing when a vehicle is
in the path.
Wire from Shadow Loop
28
Connecting Accessories
If not connecting accessories skip to next section.
The GTO/PRO SW-2500 can accept NORMALLY OPEN CONTACT accessories, such as; Push Button Entry Devices
and Key Pads.
Refer to the sensor manufacturer’s instructions for information about installing these devices on a vehicular gate.
Make sure the power to the opener is turned off
before connecting safety device wiring to the
terminal blocks. Unplugging the transformer does
not turn power to the opener OFF.
STALL FORCE
MIN
MAX
Accessory Input Connection:
OPEN
EDGE
J12
CLOSE
EDGE
EXIT
OPEN
COM
SAFETY
COM
SHADOW
LOOP
J8
J11
CYCLE
CLOSE
Connect one of the accessory wires to the COMMON (COM)
terminal and the other to the CYCLE CLOSE terminal on the
GTO/PRO SW-2500 control board.
GRN
BLK
RED
RECEIVER
Each activation of the accessory will cause the gate
to cycle as follows:
OPEN
STOP
CLOSE
STOP
Wire from Accessory
(push button, key pad, etc.)
29
Push to Open Installation
Swinging gates shall not open into public access areas!
A "Push-to-Open" gate opens out from the property.
A Push-to-Open Bracket is required for this type of installation (see
Accessory Catalog). If you have a pull-to-open gate (gate opens into the
property), return to page 13; step 3.
In a PUSH-TO-OPEN installation, the openers are installed while the gates
are in the closed position.
Step 1
Post Bracket Assembly
Determining The Mounting Position
of The Post Bracket Assembly
3/8" x 2" Bolt
Post Bracket
Push-To-Open Bracket
(optional accessory)
Post Bracket
3/8" Washer
3/8" Lock Washer
With the gates closed, adjust the post bracket assembly and the gate
bracket until the opener is level. While holding the opener level,
use C-clamps to temporarily keep the post bracket assembly and
gate bracket in their respective positions on the fence post and gate.
3/8" Nut
IMPORTANT: While determining the mounting point for the post
pivot bracket assembly, be sure that the position allows for maximum
clearance between the gate and the opener in both the open and closed
positions, as shown in the diagrams below. This clearance will give the
opener the most efficient leverage point for opening and closing the
gate and more importantly provides the least possible pinch area.
Step 2
After verifying that you have the best position for
the post pivot bracket, insert the 5/16" x 1 3/4" bolt
through the aligned holes of the post bracket and
post pivot bracket and fasten it with the 5/16"
washer and nut.
Gate in the Open Position
Pinch Area (gray)
IMPORTANT: If you loosened the clamp on the
post bracket to achieve the optimum position,
tighten it in its new position and recheck the gate
bracket with the gate in the open position (move the
gate bracket and re-clamp it if necessary).
2" minimum
Gate in the Closed Position
Pinch Area (gray)
2" minimum
30
Step 3
With the gate in the fully closed position and the opener retracted, swing the opener to the gate. Mark reference points for
bolt holes on gate cross member through middle of gate bracket slots. The opener must be level. (Some vertical adjustment is
possible by sliding the post bracket assembly up and down.) Drill 3/8" holes into the gate cross member as marked. Fasten
gate bracket to cross member using (2) 3/8" x 3" bolts, washers, lock washers, and nuts. Attach the opener to the post bracket
assembly and gate bracket using clevis pins, bushings, and hairpins clips.
Fence Post
LEVEL
Gate Post and Gate Cross Member
(In Closed Position)
Operato
r
LEVEL
POST PIVOT BRACKET level with the
horizontal surface of the GATE BRACKET
LEVE
L
Step 4
1 2 3 4 5 6 7 ON
ON
6
7
OFF
COM
Setting the Open Position Limit
COM
OPEN
EDGE
5
EXIT
OPEN
4
CLOSE
EDGE
3
SHADOW
LOOP
2
CYCLE
CLOSE
1
SAFETY
Make sure the control box power switch is OFF. Use a small
screwdriver to move the Number 4 DIP switch from the
factory setting (OFF / Pull-To-Open) to ON for Push-ToOpen. Turn power switch ON. The control board is now
configured to push the gate open.
GRN
BLK
RED
RECEIVER
DIP#4
ON
Push-to-open operation.
OFF Pull-to-open operation (factory setting).
Step 1
Confirm that the power switch is in the ON position, and the gate is in the CLOSED POSITION.
Step 2
Activate your opener by pressing the entry transmitter button. Your gate should now be moving from the closed position
toward the open position. Prepare to STOP gate by pressing the entry transmitter button again when the gate reaches the
desired open position. This step may be repeated until desired open position is achieved. Once the desired OPEN position has
been achieved, proceed to Step 3.
31
Step 3
With the gate in the desired open position PRESS & HOLD the “SET LIMIT" button on the control board for 5 seconds.
Step 4
COM
TESTING YOUR OPEN LIMIT SETTING:
J11
COM
Press the transmitter button and allow the gate to return to
the closed position. YOUR GATE’S OPEN POSITION
LIMIT IS NOW PROGRAMMED.
CYCLE
CLOSE
Press your entry transmitter and allow your gate to open. If
the OPEN position is not correct or need to be changed,
you will need to CLEAR your OPEN LIMIT settings and
follow steps one (1) to four (4) again.
SAFETY
J8
EXIT
OPEN
SHADOW
LOOP
2
4
SET
LIMIT
3
5
6
7
RED
OFF
1 2 3 4 5 6 7 ON
1
STALL FORCE
J12
BLK
RECEIVER
GRN
If you make a mistake and set the limit at the wrong
position – press your transmitter to return the gate to the
fully closed position, then press and hold the "SET LIMIT"
button for 10 seconds. This will clear the memory for the
open limit position. Follow steps one (1) to four (4) again.
MIN
LEARN
TRANSMITTER
OPEN
EDGE
CLEARING PROGRAMMED OPEN LIMIT
SETTING:
MODES ON
CLOSE
EDGE
MAX
Set Limit Button
32
Troubleshooting Guide
If your gate opener does not function properly after it is installed, use this guide before calling the GTO/
PRO Service Department.
Audible Alarm Indications
Symptom
1) Gives one short beep and no operations when you press the remote.
2) Gives a three second tone, 1 second of silence, and then another three second tone repeatedly.
3) Gives a constant tone.
Diagnosis
1) There is a power problem with the Mighty Mule 500/502, PRO-SW2500/2502, PRO-SW3000/3200 and
PRO-SW4000/4200.
- The battery could have a dead cell in it.
- The battery could be low. Disconnect the transformer or solar panel and check the battery voltage. If the
battery is fully charged, the voltage should be between 12.5 vdc to 13.5 vdc. Any voltage reading below
12vdc is low.
- The battery could be dead or disconnected at battery or board. The transformer or solar panel is powering
the board with the charge voltage. Disconnect the transformer or solar panel to see if the board still
powers up.
- The fuse is blown. Replace the fuse.
2) On the Mighty Mule 500/502, PRO-SW2500/2502, PRO-SW3000/3200 and PRO-SW4000/4200, the board
is giving a limit switch error. Check the connections on the power cable. If this does not work, check the
terminal voltages on the circuit board that is supplied to the limit switch. The voltage across the orange and
green and the brown and green should be 5 vdc without the arm connected. If the board is good, the arm will
need repair.
3) Mighty Mule 500/502, PRO-SW2500/2502, PRO-SW3000/3200 and PRO-SW4000/4200
- The battery could be very low at about 10 vdc. Flip the power switch off and back on to see if it will
clear the alarm. If the alarm is not cleared, check to make sure that there is power at the outlet. There
could be a tripped breaker or GFI. The transformer could be unplugged. The transformer could be
blown. If there is no charge power from the transformer, the green light will be off.
- The board has sensed an obstruction two times in a row. If the alarm clears by switching the power off
and on, the board is sensing an obstruction.
o
Something on or about the gate is causing the arm to push too hard to open or close the gate.
Look for something in the path of the gate or something unlevel, out of plumb, or that is binding or
pinching.
o
This can be due to a low battery when the unit is charged with a solar panel. Test the charging
circuit and the solar panel in direct sunlight.
o
If the alarm will clear by switching the power off and on, the board is sensing an obstruction.
Disconnect the arm from the gate. If it is still obstructing, increase the Stall Force. Max it out if you
have to. However, do not leave the Stall Force at this setting when connected to the gate. If the arm
is in the middle of its cycle, it extends a couple of inches, retracts a couple of inches, and the tube
does not hit the limit switch when retracted, the rev counter in the arm is bad.
33
Diagnostic LEDs
Status (Clear LED)
1) The Status LED blinks once whenever there is a change in any of the control inputs. This includes
changes to any of the seven position DIP switches on the board, the Set Limit Button or the Learn
Transmitter button is pressed, the limit switch in the arm is activated, or any of the six accessory inputs
(cycle/close, safety, exit/open, etc.) are used.
2) The Status LED flashes when the board learns a new limit.
3) Use these lights to determine if the circuit board is receiving inputs from the control inputs or the
accessories.
RF (Yellow LED)
1) The RF LED flickers whenever the antenna receiver receives a radio frequency in the 318 MHz range.
2) The RF LED flickers when the remote transmitter or the wireless keypad is activated.
3) Electronic noise that produces a 318 MHz signal will cause the RF LED to flicker. An electric motor
running is one example.
4) When the RF LED flickers, the receiver chip (U8) and the antenna receiver are working properly.
AC Power (Green LED)
1) The AC Power LED stays on whenever the transformer is putting out voltage to the circuit board. If the AC
Power LED is off, there is no power from the transformer.
2) The AC Power LED does not come on when the battery is charged by solar panel without the transformer or
when the transformer is unplugged.
Red LED
1) The Red LED comes on whenever the battery is fully charged. Any time power is drained from the
battery to operate the gate; the light goes off until the battery is fully charged again. Under normal
operations, the light will cycle on and off indicating the charging circuit is keeping the battery charged.
2) If the AC Power LED is on and:
1. Éthe Red LED is on and the unit is not working.
a. The fuse could be blown. The unit will give one short beep when the remote is
pressed or when an accessory is used.
b. The battery is not connected or there is a loose connection. Check the wires that
connect to the battery and where they connect to the circuit board from the
battery. The unit will give one short beep when the remote is pressed or when an
accessory is used.
c. The battery is no longer taking a charge. The battery could have a dead cell.
Unplug the transformer and check the voltage on the battery under a load (try to
operate the gate opener). If the voltage drops more than 1 vdc, the battery has a
dead cell. The unit will give one short beep when the remote is pressed or when
an accessory is used.
2. ...the Red LED is off.
a. The battery is charging if the unit is working. The battery voltage should
increase until it gets to 14.5 vdc.
b. The battery may be low if the unit is not working. Unplug the battery and check
the voltage. The battery should have 12.5 to 13.5 vdc. Any voltage reading
below 12 vdc is a little low and could cause intermittent or no operations.
34
3) If the AC Power LED is off and:
1. Éthe Red LED is on and the unit is not working.
a. If the unit is charging with solar in adequate sunlight, the battery is not
connected or there is a loose connection. Check the wires that connect to the
battery and where they connect to the circuit board from the battery. The unit
will give one short beep when the remote is pressed or when an accessory is
used.
b. The battery is no longer taking a charge. The battery could have a dead cell.
Disconnect the solar panel and check the voltage on the battery under a load (try
to operate the gate opener). If the voltage drops more than 1 vdc, the battery has
a dead cell. The unit will give one short beep when the remote is pressed or
when an accessory is used.
c. The fuse could be blown if the battery is being charged by solar panel. The unit
will give one short beep when the remote is pressed or when an accessory is
used.
2. Éthe Red LED is off.
a. If the unit is working, the battery is charged by a solar panel, and there is
adequate sunlight, the battery is charging.
b. If the unit is not working, the battery may be low. Disconnect the battery and
check to see if there is over 12 vdc on the battery. If not, charge the battery with
a trickle charger at 12 vdc 2 adc for three to four hours.
c. If the unit is not working, the fuse could be blown. The unit will give one short
beep when the remote is pressed or when an accessory is used.
d. If the unit is not working, the battery is not connected or there is a loose
connection. Check the wires that connect to the battery and where they connect
to the circuit board from the battery. The unit will give one short beep when the
remote is pressed or when an accessory is used.
Repair Service
If your GTO/PRO SW-2502 Gate Opener is not operating properly, please follow the steps below:
1. First use the procedures found in the Maintenance & Troubleshooting Guide (see page 33).
2. If you are unable to solve the problem, call the GTO/PRO Service Department at (800) 543-1236, or (850) 575-4144.
Refer to the serial number (located on the control box cover) and date of purchase when calling for assistance.
3. If repair or replacement of your gate opener is necessary, the Service Department will assign a Return Goods
Authorization (RGA) number to you for warranty repair.
4. Securely pack the component(s) authorized for return to the factory. Write the RGA number issued to you on the outside
of the package in LARGE BOLD PRINT. Ship the package(s) freight prepaid to:
GTO/PRO, 3121 Hartsfield Road, Tallahassee, Florida, USA 32303.
NOTE: Products returned to GTO/PRO without a Return Goods Authorization (RGA) number in LARGE
BOLD PRINT on the outside of the package WILL NOT be accepted. Also, items returned to GTO/PRO
freight collect WILL NOT be accepted.
The GTO, Inc. Technical Service Department is open
Monday – Friday 8:00 A.M. – 5:00 P.M. (Eastern Time)
1-800-543-1236 • FAX (850)575-8950
e-mail: [email protected]
35
Column Installation Information
IF THIS OPENER WILL BE USED WITH GATES THAT ARE MOUNTED ON
MASONRY, BRICK, OR ROCK (etc.) COLUMNS:
READ THE FOLLOWING CAREFULLY BEFORE PROCEEDING
A.
The simplest solution is to install the opener in a push-to-open configuration (requires Push-To-Open Bracket,
see Accessory Catalog). The minimum clearance is easier to achieve and clearance is no longer a problem,
since the opener will be pushing the gate away from the column instead of pulling it toward the column. It is
recommended that you place a steel plate between the opener mounting brackets and masonry surface for
additional strength.
B.
If a push-to-open installation is impossible due to traffic hazards, terrain, etc., another option is to re-hang the
gate. You may hang it on a post, either in the center of the column or at the back corner, or move the gate to the
back corner of the columns.
C.
The most difficult solution is to cut a notch in the column to accommodate the opener and power cable. This
job is NOT for the inexperienced!
Column Mount Example
(A + B can not exceed 14 inches)
Example: If A is 2" then B can not exceed 12"
A
Pivot Bracket
B
Gate
Column
Hinge
36
ACCESSORIES
Solar Panel (FM123), (FM122)
The Solar Panel is a 10 watt solar powered battery charger for use with the all GTO/PRO DC gate
operator systems. Particularly suited for remote installations, each Solar Panel comes with tubular
steel support, mounting clips, wire connectors, and 8 ft. of low voltage wire (see Low Voltage Wire
for additional wire). The GTO/PRO® control board has clearly labeled terminal connections for easy
installation of the Solar Panel. Installation in some regions of the world will require multiple solar
panels for adequate charging power. Solar Panel (FM122) is a 5 watt solar powered battery
charger with all the same features as (FM123).
Push Button Control (RB101)
Unlit doorbell button for remote entry or exit control. Wires directly to the control board and uses 16
gauge multi-stranded, dual conductor low voltage wire (sold separately).
Pin Lock (FM345)
The Pin Lock substitutes for the clevis pin at the front end of the GTO/PRO® 1500 gate operator.
Helps prevent theft of the operator from the gate, while allowing quick release of the operator.
Key Chain Mini Transmitter (RB744)
The Key Chain Mini Transmitter is a miniature version of the GTO/PRO® entry transmitter and has
the same adjustable code settings. 12 Volt battery included.
Entry Transmitter (RB741)
The GTO/PRO® entry transmitter, with adjustable code settings, is standard equipment with all
GTO/PRO® systems. 9 Volt battery included.
2
1
3
ABC
DEF
5
4
GHI
6
JKL
MNO
8
7
PRS
9
TUV
WXY
0
Digital Keypad (F300)
The specially designed digital keypad can be easily installed as a wireless or wired keypad. It can be
programmed to use up to fifteen different personal identification number (PIN) codes. Each code is
face programmable with additional security features built in. Wired installations require 16 gauge,
low voltage, multi-stranded, dual conductor, direct burial wire (sold separately). Requires 3 AA
batteries (not included).
GTO/PRO 50' Exit Wand (FM139), 100' Exit Wand (FM140), 150' Exit Wand (FM141)
The GTO/PRO® Exit Wand is designed for residential and agricultural applications and is
compatible with all GTO/PRO® automatic gate operator models. The wand is an electromagnetic
sensor, which offers 'hands free' operation of the GTO/PRO® Gate Operators with a 12 ft. radius of
detection of vehicles in motion.
ATIC®
CKK
TOM
LOLOC
AUTE
ITY
GASEC
UR
CTR
ON
IC
DV
9V
Per Grant
mis
sio
n
AC
CE
SS
1-8 CO
00 NT
-54 RO
3-4L
SY
28 ST
3 EM
S
Ans
wer
Key
Ba pad
tt
Low
POW
ER
ELE
Automatic Gate Lock Pull-to-Open (FM144)
A MUST for added security. Solenoid driven, with a steel housing. Unlocks and locks automatically
as gates open and close. Used with GTO/PRO® DC swing gate operating systems for maximum
stability and security. Comes with a keyed manual release. Recommended for gates over 8 ft. long.
Ideal for animal enclosures or high wind areas.
Wireless Entry Intercom / Keypad (FM136)
Allows owner to screen guest at the gate before allowing access to the property. Keypad also allows
owner to give up to 25 programmable entry codes to family, friends or approved delivery personnel.
Codes can be permanent of temporary. Can be wireless or hard wired up to 1000 feet.
37
ACCESSORIES
Replacement Battery (RB500)
Standard 12 volt, 7.0 amp-hour, maintenance-free battery for the GTO/PRO SW-2000, GTO/PRO SW-2500,
GTO/PRO SW-3000, GTO/PRO SW-4000 gate operator systems. This is the only battery approved for use
with the GTO/PRO gate operator systems. Life expectancy is 3-5 years.
Low Voltage Wire (RB509)
The 16 gauge, multi-stranded, dual conductor Low Voltage Wire is for connecting the AC powered
transformer, or the Solar Panel to the control board. Also used for the connection of accessories, such as locks,
keypads, push buttons and other wired control devices. This specially designed wire is UV treated, PVC coated
and ready for direct burial. Available in 1000' rolls or special lengths.
Push to Open Bracket (347 IH)
Required when GTO/PRO SW-2500 gate operator(s) must push the gate open, such as on a sloping driveway or
where space prevents gate(s) from opening inward (pulled open). Order two PTO brackets for conversion of a dual
swing gate installation.
Column Mount Lock Receiver (433IH)
For mounting the Automatic Gate Lock on brick columns, walls, or for other applications with limited space
between gate and post.
Replacement Transformer (RB570)
Standard 18 volt AC transformer for maintaining the battery included with the GTO/PRO SW-2500 gate operator.
This is the only transformer approved for use with all UL325 GTO/PRO gate operator systems.
HEDDOL
RECUNIV
ERSAL F
MOD
EL EIVE
294 R
Garage Door Receiver (RB709)
The Garage Door Receiver allows you to use the same GTO/PRO entry transmitter (see Dual and Triple
Transmitters) to operate your gate operator and your garage door operator. Compatible with most garage door
operators.
Dual & Triple Button Transmitters (RB742 & RB743)
The Dual (RB742) & Triple (RB743) Button Transmitters are for remote control of multiple separate gate operators,
and/or gate operator(s) and garage door operator(s) (see Garage Door Receiver). 9 Volt battery included.
If you have a question about any special order item,
just call 1-800-543-GATE!
The contents of all material available on this installation manual are copyrighted by GTO, Inc. (“GTO”), unless otherwise indicated. All rights are reserved by GTO, and content may not be reproduced,
downloaded, disseminated, published, or transferred in any form or by any means, except with the prior, written permission of GTO, Inc. Any reprinting of GTO publications is by permission only.
Copyright infringement is a violation of federal law.
GTO/PRO®, GTO/PRO® are registered trademarks of GTO, Inc. and are the exclusive property of GTO, Inc. (“GTO”).
All rights are reserved by GTO, Inc., and these marks may not be used, in any for without the prior, written permission of GTO, Inc.
38
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement